California City City Council
February 10, 2026

4913-7824-0649 v3

CERTIFICATION
I, Leanndrea Weible, Acting City Clerk of the City of California City, hereby certify that the foregoing Resolution was duly adopted at a meeting of the City Council of the City of California City on the 10th day of February 2026, by the following vote, to wit:

AYES:

NOES:

ABSENT:

ABSTAIN:

IN WITNESS WHEREOF, I have hereunto set my hand and affixed the official seal of the City of California City, California, this 10th day of February, 2026.

Leanndrea Weible
Acting City Clerk

4913-7824-0649 v3
EXHIBIT “A”
[Attached]

4898-6870-2602 v2
Agreement for Construction of Splash Pad
This Agreement for the construction of a Splash Pad (“Agreement”) is between the buyer of the Splash Pad (“Client”), on the one hand, and Splash Zone Inc. (“Contractor”), on the other hand. The terms and conditions of the Agreement are set forth below.

RESPONSIBILITY OF CLIENT
Client shall provide Contractor with adequate access and a site free of debris or obstacles prior to the start of the work. Client agrees to pay to Contractor all additional costs reasonably incurred as a result of Client’s failure to so provide.

Client shall be responsible to protect all trees, shrubs and other plants which Client desires to save which occupy space to be used in the construction of the splash pad.

Client agrees to assume all liability for damage to driveway, curbs, walks, shrubs, sewers, sprinkler systems, drip lines, patio, underground utility lines, fences, decomposed granite, lawn or any rerouting of irrigation water, except to the extent that such damage is caused by the gross negligence or willful misconduct of the Contractor.

Contractor is not liable for any damage to any part of the splash pad caused by irrigation water, vandals, or any other persons or things not within the control of the Contractor. Any splash pad equipment or appurtenances subject to this Contract delivered to the job site are the Client’s property and if removed or stolen is Client’s responsibility.

It shall be the responsibility of the Client to furnish a water source and power source for the construction of the splash pad.

Contractor is not responsible for unusual soil conditions including but not limited to the following: caliche, subterranean water, floatation of splash pad due to external water, granite, or other like and unusual sub-surface conditions, mass concrete, unusually large boulders or the like. Client agrees to pay an additional sum for these additional items and/or any associated changes as an additional cost to the contract price.

Grading and drainage beyond the splash pad area is the responsibility of the Client.

Excess soil will NOT be removed and will remain on the property unless otherwise specified in writing by Client before start of excavation.

With the exception of minor grading for the splash pad, Contractor is not responsible for supplying fill dirt or providing excessive grading unless specified in the contract.

Contractor agrees to construct the splash pad diligently, but Contractor shall not be responsible for delays or damages caused by failure to perform work or furnish materials or equipment due to acts of God, conditions created by threat or of inclement weather, war, riot, or other civil disturbance, strike, government prohibition, delays caused by Client, non issuance of all required permits affecting the splash pad, availability of construction material, or other reasons beyond its control.

Requests for any changes or additions to this Agreement desired by the Client shall be made in writing at a price as mutually agreed and signed by both parties and shall become part of this Agreement.

Contractor shall have the right to stop work and keep the job idle if payments are not made when due.

Contractor assumes no responsibility or liability for work performed by the Client, equipment or materials supplied by the Client.

In the event the payments required hereunder are not paid in accordance with the requirements of this Agreement, a credit service charge of one and one-half percent (1-1/2%) per month, which is eighteen percent (18%) corresponding annual percentage rate, will be applied from the date such payment becomes due.

In the event either party shall be required to employ an attorney to enforce any obligation of the other party under this Agreement, the non-prevailing party agrees to pay to the prevailing party a reasonable amount for attorney’s fees although legal action either was not instituted or not completed to judgment.

This Agreement together with the signed Splash Zone Proposal constitutes the full Agreement between the parties. The parties are not bound by any other statements or representations or oral expression by any agent or person purporting to act for or on behalf of either party.

Should any part on this Agreement be declared invalid for any reason, such decision shall not affect the validity of any remaining portions and shall remain in force and affect as if the invalid portion had been eliminated.

Client agrees to allow Contractor to place a Splash Zone sign on Client’s property during construction and use pictures of splash pad taken before, during and after construction in marketing and other material unless otherwise specified in writing.

When the splash pad is completed (surface material applied and start-up orientation), this Agreement shall have been completed.

LIMITED WARRANTY

MATERIALS AND WORKMANSHIP
Contractor warrants to the original Client all labor, materials, and equipment to be free of defects for a period of two (2) years from the date the splash pad is complete, when subject to original Client’s reasonable care and necessary maintenance. Upon written notice to Contractor by the original Client within that two (2) year period, Contractor will remedy any defect in material or workmanship without charge within a reasonable time provided the original Client has complied with all Terms of this Agreement, including payment in full.

LIMITATIONS
No warranty extends to any part of the splash pad, its equipment or appurtenances thereto which are caused by any of the following conditions or events:

1. Defects or failures caused by abuse, lack of reasonable care, lack of necessary maintenance, improper operation, vandalism, acts of God, or normal wear.

2. Damages or failures to plumbing lines, filter, motors and pumps caused by freezing.

3. Damages or failures caused by substituting or addition of equipment or service not expressly authorized which affect the operation or designed use of the splash pad.

4. Discoloration, staining, check cracks, cracks and imperfections inherit in splash pad decks and concrete products. Only cracks exceeding in width the thickness of a dime will be repaired by Contractor at no cost to the original consumer within the limited warranty period.

5. Minor high and/or low spots in the concrete or surface material which accumulate less than ½” inch of standing water.

6. Damages or failures caused by surface or subterranean drainage under or around said splash pad or earth fill movement, explosions, wrecking, expansive soil, and the like, and not occasioned by Contractor.

7. In some locations, expansive soil may exist. Damage caused to the splash pad as a result of expansive soil will be at the Client’s expense, except for the concrete shell, which shall be at Contractor’s expense. Client may secure at his expense an independent soil analysis to determine whether expansive soil exists in the splash pad location. Without a soil analysis, Contractor assumes no liability regarding determination of existence of expansive soil.

8. Contractor expressly denies any responsibility or liability for incidental or consequential damages arising out of or as a result of the use or ownership of the splash pad.

9. Damage by the elements or acts of God, war, civil disturbances, unusual abuse/neglect, incorrect operation or lack of care of the splash pad or equipment.

PERFORMANCE
In the event of defect in materials or workmanship within the above stated warranty period, and upon written notice to Splash Zone Inc. at 7319 S Atwood, Ste 103, Mesa, AZ 85212, by the original Client, Contractor will remedy any defect in material or workmanship without charge to the original Client with exceptions listed here within, within a reasonable amount of time, provided the original Client has complied with all terms of this Agreement, including payment in full.

NOTICE
Client is entitled to a copy of this Agreement at the time it is signed. Client may cancel this Agreement at any time prior to midnight of the third business day after the date of this transaction by faxing a written cancellation request to 866-869-3942. This provision is not allowed if construction of the splash pad has begun or will begin prior to the third business day.

Signed: Date:

Splash Zone Inc. (Contractor)
Signed: Date:

Client (Buyer)
PAGE 1 of 1

4898-6870-2602 v2
SPLASH ZONE INC. 20835 S. Ellsworth Rd., Queen Creek, AZ 85142 T. 800-985-3031 F. 866-869-3942 | www.SplashZone.com

CB 4
4912-4088-7949 v1

COUNCIL AGENDA ITEM
February 10, 2026
TO: Mayor and City Council
FROM: Joe Barragan, Public Works Director
SUBJECT: Direction on the Use of Allocated EIR Funds to Support the Street Reconstruction and Transformation Initiative (SRTI)
BACKGROUND/ DISCUSSION:

On March 25, 2025, the City Council allocated $1,395,263.44 of EIR Funds for the Streets Department and Infrastructure Projects. At the October 14, 2025, City Council meeting, the Council approved the purchase of a new Hotbox to patch potholes. On January 13, 2026, the City Council adopted Resolution 26-3205 establishing the Street Reconstruction and Transformation Initiative (SRTI). At the request of the City Council, staff has compiled a list of equipment that could be purchased with the allocated EIR funds in support of the SRTI.

The additional equipment beyond the Hotbox needed for in-house repaving of roads as contemplated in the SRTI include:
• AP555 Asphalt Paver - $579,577
• Caterpillar Pneumatic Compactor Model: CW16 - $159,410 • CB10 Asphalt Compactor - $214,432
• Asphalt Zipper - $298,691
• Crack Seal Trailer - $82,255
Total: $1,334,365
The prices provided are from quotes obtained and information on each piece of equipment is attached. Should the City Council direct the purchase of any or all of the items, a formal bid process would be initiated to achieve the best prices for each item. Alternatively, the City can rent the needed equipment at a cost of approximately $65,000 monthly should a pilot project be needed or should some or all of the equipment not be readily available to purchase and deploy.

Whether the City purchases or rents the equipment, the City does not have personnel trained on the use of the equipment nor sufficient personnel to operate the equipment given current staffing levels. As such, some of the available funds could be allocated to hire limited term staff from the local community with experience in road reconstruction to pilot the implementation of the SRTI.

CB 4
4912-4088-7949 v1
FISCAL IMPACT:

The Funds are currently in Fund 10-3644; if approved, the funds would be moved to Fund 94- 7000-76X.

RECOMMENDATION:

Staff recommends that the City Council provide direction on the use of EIR funds to support the SRTI.

ATTACHMENTS:

1. Specifications on Crack Sealer Trailer

2. Specifications on AP555 Asphalt Paver

3. Specifications on Caterpillar Pneumatic Compactor Model: CW16

4. Specifications on CB10 Asphalt Compactor

5. Specifications on Asphalt Zipper

M-Series™
Redefining Productivity:

Cimline’s new M1, M2, and M4 crack sealers build on our fifty plus years of innovation. Known for reliability, performance and productivity, contractors rave about the operator ease of use in our Cimline M-Series™ crack sealers, which range from 150 to 410-gallons capacities. Simple and safe operation makes Cimline melter applicators the preferred pavement maintenance choice by contractors and municipalities alike.

Crack Sealant
Melter Applicators

INNOVATION

IN PRESERVATION
High Quality Heated Hose System:

Cimline’s heated hose is designed and manufactured in house right here in the USA and is built for demanding high use applications in the most challenging environments The higher voltage generator powering the M1, M2, and M4 heated hose, which is now standard, reaches full temperature in just 30 minutes.

Redesigned Trailer and Tank:

A temperature probe mounted inside the pump is now standard, as is a smaller cabinet to house the pump. Both of which results in better temperature control and performance. The addition of a front recirculation port that can be used in transport mode keeps all the components hot resulting in less down time.

Quiet and Uncomplicated:

Contractors around the world give high praise over the lower loading height, low noise operation, simple automated control systems and overall operator comfort of the Cimline M-Series crack sealers.

M4 410 M2 230 M1 150
800-328-3874

CIMLINE.COM

SPECIFICATIONS
Front and rear recirculation ports 19hp Isuzu tier IV diesel power plant M4 with dual pump/dual hose option External heated 20 gpm material pump Variable material pump flow control Convenient control panel and key switch

PRODUCTS FROM CIMLINE
ME2
250 Gallon Mastic Melter Machine
P2 Two-Person Patcher with
DuraPatcher™ Technology
X2 Carry On
80CFM Air Compressor
161768
03-25
Learn more at cimline.com
Phone : 800-328-3874 Email : [email protected]
Material Capacity 150 Gallons 230 Gallons 410 Gallons
Tank Burner Heat Rating 250,000 BTU’s 290,000 BTU’s 290,000 BTU’s Heat Transfer Oil Capacity 21 Gallons 26 Gallons 38 Gallons Tank Insulation Fiberglass, 1.5 Inch Thickness
Heating Method Beckett Diesel Fired Burner
Diesel Fuel Capacity 33 Gallons
Hydraulic Capacity 33 Gallons
Engine Isuzu Tier IV 19HP Diesel
Temperature Gauge Electronic Control and 5 Inch Analog
Material Loading Height 49 Inches 50 Inches 57 Inches
Material Loading Doors Single Curbside Dual (Both Sides) Dual (Both Sides) Material Pump Rate 20 GPM 20 GPM 20 GPM
GVWR 5,515 Lbs. 6,700 Lbs. 9,950 Lbs.

GAWR 7,000 Lbs. 7,000 Lbs. 12,000 Lbs.

Axles 1x7,000 Torsion Type 2x3,500 Torsion Type 2x6,000 Torsion Type Trailer Brake Type Electric Electric Electric
Dimensions (LxWxH) 170 x 83 x 93 Inches 170 x 82 x 91 Inches 189 x 95 x 99 Inches Shipping Weight 4,200 Lbs. 4,750 Lbs. 6,450 Lbs.

Warranty 1 Year Bumper to Bumper
Cimline M-Series M1 #311-001-902 M2 #311-021-902 M4 #315-003-902 Due to continuous improvement, specifications are subject to change without notice. ©2025 Cimline Inc. All rights reserved.

AP400 | AP455
AP500 | AP555

ASPHALT PAVERS
Engine Power
AP400, AP455 90 kW (120 hp)
AP500, AP555 110 kW (148 hp)
Standard Paving Range 2.4 m - 4.7 m (8' - 15' 6")
See Technical Specifications for detailed engine emissions information.

2 AP400 | AP455 | AP500 | AP555 ASPHALT PAVERS

COMPACT ASPHALT PAVERS
The Cat® line of compact asphalt pavers provide easy transport, application versatility, and a wide paving range, making them the perfect match for urban streets, parking lots, rural roads, and many other small to mid-sized applications:
+ COMPACT SIZE
+ SIMPLE OPERATION
+ MORE FLEXIBILITY
Ready to help you make your business stronger, Cat Asphalt Pavers provide new opportunities to get the most work done at the lowest cost—so you can put more money in your pocket.

These models fit the needs of both
small and large contractors with
features that excel in urban and rural
applications.

CAT® MID-SIZED

ASPHALT PAVERS
MOBILE. TRANSPORTABLE. SERVICEABLE.

AP400 | AP455 | AP500 | AP555 ASPHALT PAVERS 3

COMPACT
SIZE
MORE

FLEXIBILITY
SIMPLE

OPERATION
The small footprint of the paver and screed
combinations simplify manueverability in
tight spaces and minimize handwork near
obstacles. In addition, the lighter weight
and optimal width accomodate easier
transport on a variety of trailer types.

Standard paving ranges from 2.4 m to

4.7 m (8' to 15' 6") with a maximum of

6.1 m (20' 6") offers contractor’s versatility
to move between commercial applications
and support work for mainline paving.

In addition, screeds with front or rear
extenders provide contractors more
options to fit their needs.

High-definition displays with short-cut
keys and similar functionality across the
entire Cat Paver and Screed line simplifies
operation. Enhanced all-around visibility
with eliminiation of the exhaust stack, and
swingout seats provide great operational
features.

4 AP400 | AP455 | AP500 | AP555 ASPHALT PAVERS

MORE REASONS TO CHOOSE A
CAT MOBIL-TRAC™

UNDERCARRIAGE

SMOOTH TRANSITIONS
The Mobil-Trac undercarriage combines a large ground
contact area with oscillating front and rear bogie sets that effortlessly crawl over milled cuts and surface irregularities to help limit tow-point movement and deliver smoother asphalt mats.

DURABLE COMPONENTS
When it comes to durability, rubber-coated components
help shed asphalt and prevent accumulation that can cause premature wear. In addition, self-tensioning accumulators, center guide blocks, and rugged internal belt cables promote lasting durability.

EXCEPTIONAL MOBILITY

INCREASES JOBSITE EFFICIENCY
Mobility is one of the keys to jobsite efficiency, maneuvering in confined areas, backing up to curbs and repositioning at the starting point are real advantages of the Cat® Mobil-Trac™ system.
48-MONTH BELT WARRANTY

HIGH SPEED TRAVEL

OSCILLATING BOGIE DESIGN

SMOOTH RIDE

EXCELLENT TRACTION






AP400 | AP455 | AP500 | AP555 ASPHALT PAVERS 5

WHEEL UNDERCARRIAGE
The wheel undercarriage combines high travel speeds with mobility and smooth turning capabilities to efficiently move around the jobsite. In addition, front-wheel assist and all-wheel drive options help maintain consistent traction, while the power turning system helps provide steady speeds through curves and turnouts.

MOBILITY AND MANEUVERABILITY
Exceptional mobility and fast travel speeds provide unmatched maneuverability around the jobsite. Additionally, the high ground clearance helps avoid storm drains, curbs, and other obstacles.

FRONT-WHEEL ASSIST
The adjustable front-wheel assist option (AP400, AP500) delivers power to the rear set of bogie wheels for increased traction to push heavy loads and power up inclines.

ALL-WHEEL DRIVE
All-wheel drive option (AP500) utilizes a flow divider that powers both sets of front bogie wheels for optimal tractive effort.

POWER TURNING SYSTEM
The power turning system utilizes a position sensor located in the left steering cylinder that helps maintain consistent travel speeds when making turns. The adjustable design
modifies the drive speed of the propel motors according to the steering angle of the front wheels, leading to better mat quality and less wear on the drive system.

FAST TRAVEL

WITH SMOOTH TURNING PERFORMANCE

6 AP400 | AP455 | AP500 | AP555 ASPHALT PAVERS
Elimination of the exhaust stack and swing out seats, provide good visibility into the hopper and auger chamber to support good material flow.

The AP400 and AP455 utilize a single sliding console, while the AP500 and AP555 are equipped with dual consoles. Both designs provide good visibility for joint matching or when precision next to obstacles is needed.

Eco-mode and Automatic Engine Speed Control combine to optimize engine speed and reduce sound levels, while the on-demand fan offers lower sound levels and draws ambient air from the side of the machine for enhanced cooling capability.

The standard ventilation system draws
air from the conveyor tunnel as well as
the auger chamber and redirects it away
from the operator for a more comfortable
working environment.

PERFORMANCE

BOOSTING

DESIGN ENHANCEMENTS
Operating conditions can have
a direct effect on performance
and quality outcomes.

ENHANCED VISIBILITY, QUIET OPERATION

AP400 | AP455 | AP500 | AP555 ASPHALT PAVERS 7

SIMILAR

FUNCTIONS

ADDITIONAL

FLEXIBILITY

SHORT-CUT
KEYS
Consistency and familiarity with paver and
screed functions help operators perform
at their best. Whether paving straight-line
rural or urban applications, Cat pavers and
screeds utilize similar functions across the
entire product line that enables personnel
to easily move between crews and train
new members when necessary.

When equipped with Cat Grade Control,
the “AUTO” buttons on the paver console
can activate/deactivate Grade Controls. In
addition, the tow-point adjusters become
target value adjusters enabling easy
modification to existing settings.

High-definition touchscreen displays
utilize simplified menu structures with
short-cut keys that provide single-touch
activation for screed heat, washdown,
and ventilation systems all from the main
menu. As with all Cat pavers, these models
also provide single-touch activation of the
feeder system and hopper fold functions.

FINGER-TIP CONTROL

SIMPLIFIES ADJUSTMENTS

8 AP400 | AP455 | AP500 | AP555 ASPHALT PAVERS

AUTOMATED FUNCTIONS
The versatility of adjustable and automated controls help operators efficiently manage material flow. Adjustable mix height dials assist when nearing obstacles and turnouts, while reversible augers and conveyors help manage material at the end of the pass.

Furthermore, automated functions help provide consistency and fight fatigue when routine conditions exist.

CONSISTENCY DRIVES QUALITY
Consistent material flow is a critical component that can help contractors achieve quality targets. A low truck entry height combines with 355 mm (14”) diameter augers too efficiently move material through the conveyors and auger chamber at both narrow and wide paving widths.

SINGLE-TOUCH ACTIVATION
The single-touch feeder system activates the entire feeder system with a single button push for better efficiency, while auto-fill simplifies starts by alternating the conveyors and augers until the mix height reaches the sensor set point.

SMOOTH MATERIAL FLOW

HELPS INCREASE QUALITY

INDEPENDENT CONTROL
Mix height adjustment from the tractor LCD display offers more control, simply use the touchscreen to modify material height in the auger chamber. The ability to control each material feed sensor independently when utilizing cut-off shoes or when paving at narrow widths is a great feature, simply switch to manual and utilize the proportional control dial to modify material flow.

SIMPLIFIED CLEANOUT
The manual fold front hopper apron on the AP400 and AP455 simplifies cleanout, while the optional power folding apron on the AP500 and AP555 goes a step further to reduce effort.

To make cleanout easier, a cleanout/warmup mode activates the augers and conveyors at slow speed, enabling the
application of release agents to help prevent material
build-up.

AP400 | AP455 | AP500 | AP555 ASPHALT PAVERS 9
Lower fuel consumption, reduced sound levels, and easier communication are real advantages of the Advanced
Eco-mode system.

ECO-MODE

ADVANCED ECO-MODE

DELIVERS
FROM 20% TO 30% MORE FUEL SAVINGS*

AUTOMATIC ENGINE

SPEED CONTROL
+ Eco-mode utilizes an engine speed of 1650 rpm and is
well-suited for most applications
+ Automatic Engine Speed Control (AESC) reduces engine
speed to 1000 rpm when the propel lever is moved to
neutral, or 1500 if screed heating is active for better overall conditions
+ Advanced Eco-mode combines Eco-mode and Automatic
Engine Speed Control for optimal fuel efficiency. It
increases engine speed to 1650 rpm when the propel
lever moves from neutral and makes modifications
based on engine load. If the upper power threshold is
exceeded, the speed will increase to 2200 rpm until the load drops below the minimum threshold and remains
there for 30 seconds.

INCREASE FUEL SAVINGS
Activate Eco-mode and Automatic Engine
Speed Control for better engine
efficiency and more fuel savings.
+

FUEL EFFICIENT POWER

BALANCES PERFORMANCE

BETTER FUEL ECONOMY
* Fuel savings may vary by paver model, paving conditions and application. Consult your Cat dealer for more information.

10 AP400 | AP455 | AP500 | AP555 ASPHALT PAVERS
The Cat Grade Control option helps deliver smoother surfaces and control mat thickness for increased performance, lower operating costs, and higher profitability. Text-based user-friendly displays, accurate control, and great reliability can help ensure quality targets are being met.

TEXT-BASED DISPLAYS
User-friendly system with text-based displays allow
operation from the paver or screed consoles (screed display required). Split-screen mode enables a single-side operator to monitor settings for each side of the screed.

QUICK ACCESS
The Grade Control activation button enables operators to toggle between Grade Control and the previous screen. Simply press the Grade Control activation button a second time and the system returns to the previous screen.

EASY SETUP
Simple activation of the 10-point auto-calibration helps eliminate over/under adjustment, while cross-coupling
maintains slope and height when height adjustments
are made.

RELIABLE SYSTEM
The highly reliable system utilizes water-resistant displays and sealed components with-stand heat, moisture, and vibration.

The system is compatible with Cat Electronic Technician (Cat ET) for simplified diagnostics.

CAT GRADE CONTROL

OPTIMIZES YIELD AND QUALITY

AP400 | AP455 | AP500 | AP555 ASPHALT PAVERS 11
The Cat SE47 FM Asphalt Screed features front extenders, multiple berm options, and a small foot print for starting next to curbs and obstacles. The front extenders excel in applications with varying paving widths and enables quick reaction when manuevering around obstacles.
+ Front extenders provide the ability to retract without first clearing material from the extenders, simplifying maneuverability around obstacles
+ Power berm options provide 305 mm (12") or 457 mm (18") wide berms with a variable height up to 102 mm (4")
+ Inner and outer strike-off adjustments are connected
to provide single point modification that ensures equal adjustment across the width of the screed
+ Remote pendents offer mix height adjustments for
complete control from extended positions
The Cat SE47 V Asphalt Screed with rear extenders provides stability, easy set-up, and a versatile paving range. The rear extenders deliver smooth material flow and excellent stability on wide width paving applications.
+ Rear extenders provide effortless material flow to the end gates when increasing paving widths
+ Walkway clearance height of 127 mm (5") enables close starting capability next to curbs and other obstacles
+ Simple, bolt-on extensions offer a maximum paving width of 6.1 m (20')
+ Remote pendents offer mix height adjustments for
complete control from extended positions

ASPHALT SCREEDS

APPLICATION VERSATILITY
Cat Asphalt Screeds come equipped with front or rear extenders that provide high quality results for parking lots, urban streets, and rural roads. The easy-to-use operating consoles and standard remote pendants provide the ability to modify material flow from the screed or remotely. When equipped with Cat Grade Control, conveyor ratio adjustment or conveyor material height can be performed through the displays.

SE47 FM (4B5) ASPHALT SCREED

FRONT-EXTENDER VERSATILITY
SE47 V ASPHALT SCREED

REAR-EXTENDER STABILITY

12 AP400 | AP455 | AP500 | AP555 ASPHALT PAVERS

PARTS AND SERVICE

EXTEND MACHINE LIFE

DOWNLOAD THE PARTS
REFERENCE GUIDE TODAY!
Whether you are a Do-it-myself, Do-it-with-me, or a Do-itfor-me customer, Cat dealers are ready to assist with parts orders to complete rebuilds of your equipment.

DO-IT-MYSELF – If you prefer to do the work in-house, your Cat dealer can help you determine parts needs. One of our experts will utilize Caterpillar Service Information, or can perform a (TA1) visual inspection, or (TA2) technical inspection to help identify parts replacement needs.

DO-IT-WITH-ME – In addition to providing parts, Cat dealers can supplement your repair capabilities with fully trained technicians and specialized tooling.

DO-IT-FOR-ME – Cat dealers can manage the replacement of vital wear parts or a complete rebuild. Ask your dealer about an inspection and a repair option plan to meet your needs.

CERTIFIED PAVER REBUILDS – Take advantage of the extra
value built into Cat equipment. The Cat Certified Rebuild Programs return your end-of-life machines, systems, and components to like-new condition at a fraction of the cost. From single component to complete machine options, we’ve got you covered.

REPAIR WITH GENUINE CAT PARTS

GET FULL ACCESS TO

SERVICE AND REPAIR KITS
The Parts Reference Guide includes diagrams, part descriptions and part number lists for common wear and maintenance
components to make online or in person ordering fast an easy.

AP400 | AP455 | AP500 | AP555 ASPHALT PAVERS 13

ELIMINATE THE GUESSWORK
Cat equipment management technology helps take the complexity out of managing multiple jobsites – by gathering data generated from equipment, materials, as well as people and serving it up in customizable formats.

CAT EQUIPMENT MANAGEMENT TECHNOLOGY
VISIONLINK®

EQUIPMENT MANAGEMENT
Remote Services* is a suite of technologies that help improve jobsite efficiency.
+ Remote Troubleshoot allows Cat dealers to perform
diagnostic testing and pinpoint potential issues on connected machines while in operation. It can also help ensure that technicians arrive with the correct parts and tools the first time, eliminating additional trips to save time and money. + Remote Flash allows updates to onboard software without a technician being present. Enabling the initiation of software updates when convenient can help increase overall
operating efficiency.
* Must be within cell range coverage.

REMOTE SERVICES

EQUIPMENT MANAGEMENT
Caterpillar releases products, services and technologies in each region at different time intervals. Please verify with your local Cat dealer for technology availability and specifications.

VisionLink® takes the guesswork out of managing entire
fleets regardless of size or equipment manufacturer.* Review equipment data from desktop or mobile devices to maximize uptime and optimize assets. With interactive dashboards, VisionLink makes it easier for operations of all sizes to make informed decisions that lower costs and boost productivity.

With various subscription-level options, Cat dealers can help determine what’s needed to connect your fleet and help manage your business.
+ 24/7 Fleet Monitoring
+ Mixed Fleet Management
+ Optimize Fleet Utilization
+ Track Assets by Location
+ View Asset Health Status
+ Review Inspection Reports
+ Assign Maintenance Tasks
+ Schedule Downtime
+ Request Service Parts
Orders
+ Download Summary
Reports

14 AP400 | AP455 | AP500 | AP555 ASPHALT PAVERS

POWERTRAIN
Engine Model Cat C3.6
Emissions U.S. EPA Tier 4 Final
Engine Power @ 2200 rpm (ISO 14396-2002) 90 kW 120 hp
Speed – Paving 61 m/min 200 ft/min
Speed – Travel 16 km/hr 10 mph
Tire Size 15.5 R25
AP400 TECHNICAL SPECIFICATIONS

DIMENSIONS
1 Operating Length w/ SE47 V Screed 5784 mm 19'
Shipping Length w/ SE47 V Screed 5523 mm 18' 1"
1 Operating Length w/ SE47 FM Screed 5740 mm 18' 10"
Shipping Length w/ SE47 FM Screed 5505 mm 18' 1"
2 Operating Width (hoppers lowered) 3281 mm 10' 9"
3 Operating Height (beacon) 3252 mm 11'
4 Operating Platform height 1731 mm 5' 8"
5 Transport Height (steering wheel) 2853 mm 9' 4"
6 Transport Width w/ End Gates 2590 mm 8' 6"
7 Truck Entry Width 3161 mm 10' 4"
8 Truck Entry Height (hopper) 544 mm 21"
Truck Entry Height (apron) 498 mm 20"
Ground Clearance 203 mm 8"
9 Hopper Length 1803 mm 5' 11"
10 Axle to Axle (center drive to front idler) 2372 mm 93" Auger Diameter 355 mm 14"

CAPACITIES
Maximum Throughput Capacity 774 Tonnes 853 US Tons
Hopper Capacity 5.8 m3
205 ft3
Fuel Tank 200 L 53 gal
Cooling System 24 L 6.3 gal
Engine Oil 11 L 2.9 gal
Hydraulic Tank 121 L 32 gal
Diesel Exhaust Fluid (DEF) Tank 19 L 5 gal
Washdown Spray Tank 32 L 8.5 gal

MACHINE WEIGHT
Paver Only (shipping) 10 581 kg 23,327 lb
Operating w/ SE47 V Screed 13 510 kg 29,800 lb
Operating w/ SE47 FM Screed 13 618 kg 30,000 lb
Operating weights are approximate and include coolant, lubricants, full fuel tank , 75 kg (165 lb) operator, and grade control components.

PAVING RANGE
SE47 V
Standard Range 2.4 m - 4.7 m 8' - 15' 6"
Maximum Width w/ Extensions 6.1 m 20'
SE47 FM
Standard range 2.4 m - 4.7 m 8' - 15' 6"
Maximum Width w/ Extensions 5.9 m 19' 6"
8 9
1 10
4 5
3 2
7 6

AP400 | AP455 | AP500 | AP555 ASPHALT PAVERS 15
8 9
1 10
4 5
3 2
7 6

POWERTRAIN
Engine Model Cat C3.6
Emissions U.S. EPA Tier 4 Final
Engine Power @ 2200 rpm (ISO 14396-2002) 90 kW 120 hp
Speed – Paving 61 m/min 200 ft/min
Speed – Travel 11 km/hr 7 mph
AP455 TECHNICAL SPECIFICATIONS

DIMENSIONS
1 Operating Length w/ SE47 V Screed 5784 mm 19'
Shipping Length w/ SE47 V Screed 5523 mm 18' 1"
1 Operating Length w/ SE47 FM Screed 5740 mm 18' 10"
Shipping Length w/ SE47 FM Screed 5505 mm 18' 1"
2 Operating Width (hoppers lowered) 3281 mm 10' 9"
3 Operating Height (beacon) 3275 mm 10' 9"
4 Operating Platform height 1655 mm 5' 5"
5 Transport Height (steering wheel) 2814 mm 9' 3"
6 Transport Width w/ End Gates 2590 mm 8' 6"
7 Truck Entry Width 3161 mm 10' 4"
8 Truck Entry Height (hopper) 567 mm 22"
Truck Entry Height (apron) 525 mm 21"
Ground Clearance 210 mm 8"
9 Hopper Length 1803 mm 5' 11"
10 Axle to Axle (center drive to front idler) 2533 mm 100" Auger Diameter 355 mm 14"

CAPACITIES
Maximum Throughput Capacity 774 Tonnes 853 US Tons
Hopper Capacity 5.8 m3
205 ft3
Fuel Tank 200 L 53 gal
Cooling System 24 L 6.3 gal
Engine Oil 11 L 2.9 gal
Hydraulic Tank 121 L 32 gal
Diesel Exhaust Fluid (DEF) Tank 19 L 5 gal
Washdown Spray Tank 32 L 8.5 gal

MACHINE WEIGHT
Paver Only (shipping) 11 266 kg 24,837 lb
Operating w/ SE47 V Screed 14 194 kg 31,292 lb
Operating w/ SE47 FM Screed 14 303 kg 31,533 lb
Operating weights are approximate and include coolant, lubricants, full fuel tank , 75 kg (165 lb) operator, and grade control components.

PAVING RANGE
SE47 V
Standard Range 2.4 m - 4.7 m 8' - 15' 6"
Maximum Width w/ Extensions 6.1 m 20'
SE47 FM
Standard range 2.4 m - 4.7 m 8' - 15' 6"
Maximum Width w/ Extensions 5.9 m 19' 6"

16 AP400 | AP455 | AP500 | AP555 ASPHALT PAVERS
4 5
3 2
7 6

POWERTRAIN
Engine Model Cat C4.4
Emissions U.S. EPA Tier 4 Final
Engine Power @ 2200 rpm (ISO 14396-2002) 110 kW 148 hp
Speed – Paving 61 m/min 200 ft/min
Speed – Travel 16 km/hr 10 mph
Tire Size 17.5 R25
AP500 TECHNICAL SPECIFICATIONS

DIMENSIONS
1 Operating Length w/ SE47 V Screed 5909 mm 19' 4"
Shipping Length w/ SE47 V Screed 5648 mm 18' 6"
1 Operating Length w/ SE47 FM Screed 5865 mm 19' 3"
Shipping Length w/ SE47 FM Screed 5630 mm 18' 6"
2 Operating Width (hoppers lowered) 3281 mm 10' 9"
3 Operating Height (beacon) 3352 mm 11'
4 Operating Platform height 1731 mm 5' 8"
5 Transport Height (steering wheel) 2890 mm 9' 6"
6 Transport Width w/ End Gates 2590 mm 8' 6"
7 Truck Entry Width 3149 mm 10' 4"
8 Truck Entry Height (hopper) 537 mm 21"
Truck Entry Height (apron) 507 mm 20"
Ground Clearance 197 mm 7.8"
9 Hopper Length 1925 mm 6' 4"
10 Axle to Axle (center drive to front idler) 2338 mm 92" Auger Diameter 355 mm 14"

CAPACITIES
Maximum Throughput Capacity 1000 Tonnes 1100 US Tons
Hopper Capacity 6.1 m3
215 ft3
Fuel Tank 200 L 53 gal
Cooling System 24 L 6.3 gal
Engine Oil 9 L 2.4 gal
Hydraulic Tank 121 L 32 gal
Diesel Exhaust Fluid (DEF) Tank 19 L 5 gal
Washdown Spray Tank 32 L 8.5 gal

MACHINE WEIGHT
Paver Only (shipping) 11 481 kg 25,311 lb
Operating w/ SE47 V Screed 14 409 kg 31,772 lb
Operating w/ SE47 FM Screed 14 518 kg 32,012 lb
Operating weights are approximate and include coolant, lubricants, full fuel tank , 75 kg (165 lb) operator, and grade control components.

PAVING RANGE
SE47 V
Standard Range 2.4 m - 4.7 m 8' - 15' 6"
Maximum Width w/ Extensions 6.1 m 20"
SE47 FM
Standard range 2.4 m - 4.7 m 8' - 15' 6"
Maximum Width w/ Extensions 6.2 m 20' 6"
8 9
1 10

AP400 | AP455 | AP500 | AP555 ASPHALT PAVERS 17
8 9
1 10
4 5
3 2
7 6

POWERTRAIN
Engine Model Cat C4.4
Emissions U.S. EPA Tier 4 Final
Engine Power @ 2200 rpm (ISO 14396-2002) 110 kW 148 hp
Speed – Paving 61 m/min 200 ft/min
Speed – Travel 11 km/hr 7 mph
AP555 TECHNICAL SPECIFICATIONS

DIMENSIONS
1 Operating Length w/ SE47 V Screed 5909 mm 19' 4"
Shipping Length w/ SE47 V Screed 5648 mm 18' 6"
1 Operating Length w/ SE47 FM Screed 5865 mm 19' 3"
Shipping Length w/ SE47 FM Screed 5630 mm 18' 6"
2 Operating Width (hoppers lowered) 3281 mm 10' 9"
3 Operating Height (beacon) 3352 mm 11'
4 Operating Platform height 1731 mm 5' 8"
5 Transport Height (steering wheel) 2890 mm 9' 6"
6 Transport Width w/ End Gates 2590 mm 8' 6"
7 Truck Entry Width 3149 mm 10' 4"
8 Truck Entry Height (hopper) 537 mm 21"
Truck Entry Height (apron) 507 mm 20"
Ground Clearance 197 mm 7.8"
9 Hopper Length 1925 mm 6' 4"
10 Axle to Axle (center drive to front idler) 2338 mm 92" Auger Diameter 355 mm 14"

CAPACITIES
Maximum Throughput Capacity 1000 Tonnes 1100 US Tons
Hopper Capacity 6.1 m3
215 ft3
Fuel Tank 200 L 53 gal
Cooling System 24 L 6.3 gal
Engine Oil 9 L 2.4 gal
Hydraulic Tank 121 L 32 gal
Diesel Exhaust Fluid (DEF) Tank 19 L 5 gal
Washdown Spray Tank 32 L 8.5 gal

MACHINE WEIGHT
Paver Only (shipping) 12 244 kg 26,993 lb
Operating w/ SE47 V Screed 15 172 kg 33,448 lb
Operating w/ SE47 FM Screed 15 281 kg 33,689 lb
Operating weights are approximate and include coolant, lubricants, full fuel tank , 75 kg (165 lb) operator, and grade control components.

PAVING RANGE
SE47 V
Standard Range 2.4 m - 4.7 m 8' - 15' 6"
Maximum Width w/ Extensions 6.1 m 20'
SE47 FM
Standard range 2.4 m - 4.7 m 8' - 15' 6"
Maximum Width w/ Extensions 6.2 m 20' 6"

18 AP400 | AP455 | AP500 | AP555 ASPHALT PAVERS

OPERATOR ENVIRONMENT STANDARD OPTIONAL
Canopy 
Deceleration Pedal 
Dual operating consoles (AP500) 
Heated Seat 
Single Sliding Console (AP400) 
Steering Guide 
Umbrella – tractor or screed 
Ventilation System 
Side Shields 
Windshield – requires canopy 

MATERIAL DELIVERY STANDARD OPTIONAL
Auger Extensions – 0.15 m (6") 
Auger Extensions – 0.46 m (1.5') 
Mainframe Extensions – power 
Mainframe Extensions – manual 
Material Feed Sensors – contact 
Material Feed Sensors – sonic 
Push-roller – adjustable 
Truck Hitch 
Wash-down Pump and Reel 
AP400 / AP500 STANDARD & OPTIONAL EQUIPMENT
Standard and optional equipment may vary. Consult your Cat dealer for details.

TECHNOLOGY STANDARD OPTIONAL
Cat® Grade Control 
Basic Grade Control 
Product Link™ Elite 643 (cellular) 
Product Link Elite 683 (cellular/satellite) 

POWERTRAIN STANDARD OPTIONAL
All-wheel Drive (AP500) 
Ballast – front weights 
Cat C3.6 – four-cylinder (AP400) 
Cat C4.4 – four-cylinder (AP500) 
Cooling Fan – variable speed 
Front-wheel Assist 
Radial Drive Tires 
Sand-rib Drive Tires 

ELECTRICAL SYSTEM STANDARD OPTIONAL
1400 CCA Battery 
150-amp Alternator 
12-volt Charging System 
Automotive-type Fuse System 
Auto-reset Breaker for Material Sensors 
Battery – maintenance-free 
Cat Electronic Technician (Cat ET) 

SAFETY AND SECURITY STANDARD OPTIONAL
Alarm – back-up 
Horn – warning (front and rear) 
Lights – LED Working 
Lights – LED Roading 
Mirror Package 
Warning Beacon – LED 

SERVICE AND MAINTENANCE STANDARD OPTIONAL
Hydraulic Oil – Cat HYDO™ Advanced 
Remote Access Drains 
Remote Flash 
Service Repair Kits 
Sampling Ports for Scheduled Oil Sampling
(S·O·SSM) 
Sight Gauges – engine coolant, hydraulic oil 

AP400 | AP455 | AP500 | AP555 ASPHALT PAVERS 19

OPERATOR ENVIRONMENT STANDARD OPTIONAL
Canopy 
Deceleration Pedal 
Dual operating consoles (AP555) 
Heated Seat 
Single Sliding Console (AP455) 
Steering Guide 
Steering – friction 
Steering – spring return 
Umbrella – tractor or screed 
Ventilation System 
Side Shields 
Windshield – requires canopy 

MATERIAL DELIVERY STANDARD OPTIONAL
Auger Extensions – 0.15 m (6") 
Auger Extensions – 0.46 m (1.5') 
Mainframe Extensions – power 
Mainframe Extensions – manual 
Material Feed Sensors – contact 
Material Feed Sensors – sonic 
Push-roller – adjustable 
Truck Hitch 
Wash-down Pump and Reel 
AP455 / AP555 STANDARD & OPTIONAL EQUIPMENT
Standard and optional equipment may vary. Consult your Cat dealer for details.

TECHNOLOGY STANDARD OPTIONAL
Cat Grade Control 
Basic Grade Control 
Product Link™ Elite 643 (cellular) 
Product Link Elite 683 (cellular/satellite) 

POWERTRAIN STANDARD OPTIONAL
Ballast – front weights 
Cat C3.6 – four-cylinder (AP455) 
Cat C4.4 – four-cylinder (AP555) 
Cooling Fan – variable speed 
Mobil-trac belt™ – smooth belt 

ELECTRICAL SYSTEM STANDARD OPTIONAL
1400 CCA Battery 
150-amp Alternator 
12-volt Charging System 
Automotive-type Fuse System 
Auto-reset Breaker for Material Sensors 
Battery – maintenance-free 
Cat Electronic Technician (Cat ET) 
Remote start charge receptacle (AP455) 

SAFETY AND SECURITY STANDARD OPTIONAL
Alarm – back-up 
Horn – warning (front and rear) 
Lights – LED Working 
Lights – LED Roading 
Mirror Package 
Warning Beacon – LED 

SERVICE AND MAINTENANCE STANDARD OPTIONAL
Hydraulic Oil – Cat HYDO™ Advanced 
Remote Access Drains 
Remote Flash 
Service Repair Kits 
Sampling Ports for Scheduled Oil Sampling
(S·O·SSM) 
Sight Gauges – engine coolant, hydraulic oil 

QEHQ3219 (10/2023)
Build Number: 07A
N Am
For more complete information on Cat products, dealer services and industry solutions, visit us on the web at www.cat.com
Materials and specifications are subject to change without notice. Featured machines in photos may include additional equipment. See your Cat dealer for available options. © 2023 Caterpillar. All Rights Reserved. CAT, CATERPILLAR, LET’S DO THE WORK, their respective logos, “Caterpillar Corporate Yellow”, the “Power Edge” and Cat “Modern Hex” trade dress as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.

VisionLink is a trademark of VisualSite LLC, registered in the United States and in other countries.

The Cat® CW16 is a standard 9-wheel pneumatic roller with an option to increase to 11 wheels. Equipped with an efficient Cat engine, this machine delivers smooth, reliable compaction performance on asphalt and soft base materials.
n Exceptional Visibility and Control with a rotating operating station, LCD display and touch-pad machine functions. ROPS or Sun Canopy options are available.
n Smooth Operating Powertrain with Eco-mode, electronic propel control and smooth braking system. An exclusive two-speed hydrostatic propel system delivers excellent maneuverability with speeds up to 19 km/hr (12 mph). The system shifts smoothly between speed ranges while also providing the ability to coast for a fuel saving enhancement.
n Versatile Compaction Performance is offered by the flexible ballast options, and oscillating front wheels. Ballast options include steel, sand, and water, making it easy to adjust operating weights and match job site requirements. Oscillating front wheels deliver compaction across the entire machine width for excellent results.
n Pickup Prevention provided by the pressurized water spray system, wheel scrapers or cocoa mats, and optional heat retention aprons help keep asphalt and aggregates on the road surface where they belong. n Best Lifetime Value delivered through Eco-mode, efficient engine, and exclusive propel control minimize life-time operating costs and maximize profit.

Top Features
Specifications
Operating Weights Load per Wheel
CW16 w/Standard 9 Wheels
Base machine 5200 kg 11,464 lb 0.58 mt
w/Water 8700 kg 19,180 lb 0.97 mt
w/Wet Sand 12 200 kg 26,896 lb 1.36 mt
w/Steel 8500 kg 18,739 lb 0.94 mt
w/Steel and Water 11 750 kg 25,904 lb 1.31 mt
w/Steel and Wet Sand 15 000 kg 33,069 lb 1.67 mt
CW16 w/11 Wheel Option
Base machine 5300 kg 11,685 lb 0.48 mt
w/Water 8800 kg 19,400 lb 0.80 mt
w/Wet Sand 12 300 kg 27,117 lb 1.11 mt
w/Steel 8600 kg 18,960 lb 0.78 mt
w/Steel and Water 11 750 kg 25,904 lb 1.06 mt
w/Steel and Wet Sand 14 900 kg 32,849 lb 1.35 mt
Cat® C3.4B Engine* 75 kW 101.9 hp (M) 100.5 hp (I)
* Engine meets U.S. EPA Tier 4 Final and EU Stage IV emissions * Turbo-charged
Number of cylinders 4
Rated speed 2200 rpm
Cat C4.4 Engine** 75 kW 101.9 hp (M) 100.5 hp (I)
** Engine meets emissions equivalent to U.S. EPA Tier 3, EU Stage IIIA, and China Stage III.

Number of cylinders 4
Rated speed 2200 rpm
Travel Speed Ranges:
low 0 - 9 km/hr 6 mph
high 0 - 19 km/hr 12 mph
CW16 w/C3.4B Engine
Fuel tank 135 L 35.7 gal
DEF tank 19 L 5 gal
Cooling system 16.6 L 4.4 gal
Engine oil w/filter 6.5 L 1.7 gal
Hydraulic tank 31.9 L 8.4 gal
Water tank 348 L 92 gal
CW16 w/C4.4 Engine
Fuel tank 146 L 38 gal
Cooling system 18.3 L 4.8 gal
Engine oil w/filter 9.5 L 2.5 gal
Hydraulic tank 31.9 L 8.4 gal
Water tank 348 L 92 gal
Weights Service Refill Capacities
Engine – Powertrain
Cat®
CW16
Pneumatic Tire Roller

Weight per Wheel
CW16 Pneumatic Compactor
12-Ply

7.5 x 15
Radial Tire
14-Ply

7.5 x 15
Bias Tire
Tire Pressure
kPa 344 413 482 550 619 688 757 344 413 482 550 619 688 757 826 862 psi 50 60 70 80 90 100 110 50 60 70 80 90 100 110 120 125 Average Wheel Load
545 kg
1,200 lb
GCP kPa 236 266 284 306 317 317 344 243 266 284 295 317 330 344 359 367 psi 34 39 41 44 46 46 50 35 39 41 43 46 48 50 52 53
970 kg
2,145 lb
GCP kPa 250 284 314 343 369 378 410 259 295 321 343 369 388 420 421 427 psi 36 41 46 50 54 55 60 38 43 47 50 54 56 60 61 62
1440 kg
3,180 lb
GCP kPa 280 304 331 358 390 405 607 273 312 336 364 390 413 437 465 475 psi 41 44 48 52 57 59 88 40 45 49 53 57 60 64 68 69
5 Dimensions
1 Overall length 4290 mm 14’ 1"
2 Compaction width
9 wheel - Radial 1728 mm 68”
9 wheel - Bias 1754 mm 69”
11 wheel - Radial 2103 mm 83”
11 wheel - Bias 2132 mm 84”
Tire overlap - Radial 32 mm 1.25"
Tire overlap - Bias 36 mm 1.42”
3 Wheelbase 3340 mm 10’ 11"
4 Ground clearance 267 mm 10.5”
5 Height (steering wheel) 2320 mm 91"
6 Height (ROPS) 3000 mm 9' 10"
QEHQ1965-02 (08-2022)
CW16 Pneumatic Tire Roller
4 3
6 2 1
Ground Contact Pressures
For more information on Cat products, dealer services, and industry solutions visit us on the web at www.cat.com. © 2022 Caterpillar
All rights reserved.

Materials and specifications are subject to change without notice. Featured machines in photos may include additional equipment.

See your Cat dealer for available options.

CAT, CATERPILLAR, LET’S DO THE WORK, their respective logos, “Caterpillar Corporate Yellow,” the “Power Edge” and Cat “Modern Hex” trade dress as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.

CB7 | CB8 | CB10 | CB13 | CB15 | CB16 | CD8 | CD10 TANDEM VIBRATORY ROLLERS 1

TANDEM VIBRATORY ROLLERS
CB7 | CB8 | CB10 | CB13 | CB15 | CB16
CD8 | CD10

2 CB7 | CB8 | CB10 | CB13 | CB15 | CB16 | CD8 | CD10 TANDEM VIBRATORY ROLLERS

TANDEM VIBRATORY ROLLERS
The Cat® line of Tandem Vibratory Rollers offer many technological enhancements that provide better control, more versatility, and increased efficiency:
+ 360º SEAT POSITIONING
+ OSCILLATORY VIBRATION
+ CAT COMPACTION CONTROL
Ready to help you make your business stronger, Cat Tandem Vibratory Rollers give you new ways to get the most work done at the lowest cost—so you put more money in your pocket.

CAT® TANDEM

VIBRATORY ROLLERS
These models deliver excellent mat
densities, good visibility and comfort,
fuel efficiency with Eco-mode, and
unmatched reliability.

RELIABLE. COMFORTABLE. PRODUCTIVE.

CB7 | CB8 | CB10 | CB13 | CB15 | CB16 | CD8 | CD10 TANDEM VIBRATORY ROLLERS 3

PASS-COUNT AND

TEMPERATURE MAPPING
Helps ensure the mat gets covered completely
when optimal temperatures exist. It combines
infrared temperature sensors with GPS mapping
to keep the operator informed of current asphalt
temperatures, machine position, pass-count, and
layer coverage.

ELIMINATE CONCERNS

CAT COMPACTION CONTROL

IS HERE TO ASSIST
Traffic, haul trucks, paver stops, night-time operation are genuine concerns when operating an asphalt compactor.

The degree to which these become distractions can have a direct affect on the quality of the pavement. Did every part of the mat receive the same number of passes? Was the asphalt temperature conducive for compaction? Was the base
prepared correctly? Where did I stop on the previous pass? Do I have the amplitude set correctly?
The following Cat Compaction Control Technologies can help provide answers to these questions.

COMPACTION METER

VALUE (CMV)
Utilizes a drum-mounted accelerometer to
measure the combined stiffness of the asphalt
layer, base layer, and sub-base layer. It can help
indicate issues with the road structure, even
beneath the asphalt layer.

AUTO-ADJUSTABLE

COMPACTION
Optimizes efficiency by delivering the highest
level of amplitude that the asphalt can receive
without over-compacting. A dedicated
accelerometer on each drum makes sensitivity
adjustments in a fraction of a second for peak
compaction performance. Available on CB10 and
CD10 models only.

MACHINE-TO-MACHINE

COMMUNICATION
Helps keep rolling patterns in sync by sharing
mapped data such as CMV, temperature
mapping, coverage area, and pass-count maps
between the displays of multiple machines.

4 CB7 | CB8 | CB10 | CB13 | CB15 | CB16 | CD8 | CD10 TANDEM VIBRATORY ROLLERS Working in unfavorable conditions is typical in the
paving business, but the operating station helps
keep operators comfortable, safe, and productive.

KEEP MOVING FORWARD
Visibility and comfort are enhanced by the 360°
seat positioning option that enables the operator
to always face the direction of travel. Handwheel
steering technology eliminates the front steering
console, enabling the operator to easily monitor
water spray performance as well as oncoming
obstacles. An optional 8-button control panel
simplies control for efficient performance.
360° SEAT POSITIONING

ENHANCES SAFETY

CB7 | CB8 | CB10 | CB13 | CB15 | CB16 | CD8 | CD10 TANDEM VIBRATORY ROLLERS 5

BECOME MORE VERSATILE

WITH OSCILLATORY VIBRATION
The design combines high-performance vertical
vibration on the front drum with oscillation
technology on the rear drum. The front drum
with vertical vibration is available in two
amplitude, five amplitude, or Versa-Vibe systems
that provide initial compaction, while the rear
drum with oscillation continues the excellent
performance for optimal smoothness and density.
• Proven pod-style eccentric weight technology developed by Caterpillar
• 2 year/2000 hour service interval helps maximize uptime and limit maintenance costs.
• Durable power-transmission delivers 2-times the load capacity of timing belt systems leading to extended life
• Standard drum and optional hardened drum shells offer exceptional long-term life on a variety of mix designs and delivers outstanding mat texture, density, and smoothness. * Refer to the price list for model availability.

UNIQUE FEATURES

6 CB7 | CB8 | CB10 | CB13 | CB15 | CB16 | CD8 | CD10 TANDEM VIBRATORY ROLLERS CD8 CD10
ENGINE
Gross Power 75 kW 102 mhp 100 hp 75 kW 102 mhp 100 hp

MACHINE WEIGHT
Operating Weight with Split Drum 8390 kg 18,497 lb 10 120 kg 22,311 lb Operating Weight – Maximum 9450 kg 20,834 lb 11 440 kg 25,220 lb Static Linear Load 27.9 kg/cm 170 lb/in 29.5 kg/cm 165 lb/in

DIMENSIONS
Overall Length 4284 mm 13 ft 10 in 4322 mm 14 ft 2 in
Overall Width 1664 mm 66 in 1874 mm 74 in
Height 2940 mm 9 ft 8 in 2985 mm 9 ft 9 in
Compaction Width 1500 mm 59 in 1700 mm 67 in
Drum Offset – Optional 1320 mm 51 in 1320 mm 51 in

VIBRATORY SPECIFICATIONS
Amplitude – Maximum 0.65 mm 0.026 in 0.84 mm 0.033 in
Frequency – Minumum/Maximum 42/63.3 Hz – 2,520/3,800 vpm 42/53.3 Hz – 2,520/3,200 vpm Centrifugal Force – Maximum 73.8 kN 16,590 lbF 128.9 kN 28,977 lbF

SERVICE REFILL CAPACITIES
Fuel Tank Capacity 135 L 36 gal 191 L 50 gal
Water Tank Capacity 600 L 159 gal 750 L 198 gal

MANEUVERABILITY MEETS PERFORMANCE
The exclusive drum steer propel system provides a tight turning radius without damaging the hot mat. When turning, the outside drum half rotates faster than the inside drum, eliminating the potential for shoving and tearing that can occur on standard one-peice drum designs.

A TURN FOR THE BETTER

SPLIT DRUMS ELIMINATE TEARING WHEN TURNING

CB7 | CB8 | CB10 | CB13 | CB15 | CB16 | CD8 | CD10 TANDEM VIBRATORY ROLLERS 7 CB7 CB8 CB10
ENGINE
Gross Power 75 kW 102 mhp 100 hp 75 kW 102 mhp 100 hp 98 kW 133 mhp 131 hp

MACHINE WEIGHT
Operating Weight with ROPS 7990 kg 17,615 lb 8520 kg 18,783 lb 9500 kg 20,945 lb Operating Weight – Maximum 8720 kg 19,224 lb 9250 kg 20,343 lb 10 235 kg 22,564 lb Static Linear Load 26.3 kg/cm 147 lb/in 25.1 kg/cm 141 lb/in 27.8 kg/cm 156 lb/in

DIMENSIONS
Overall Length 4565 mm 14 ft 5 in 4565 mm 14 ft 5 in 4565 mm 14 ft 5 in Overall Width 1670 mm 65 in 1862 mm 73 in 1872 mm 74 in Height 2980 mm 9 ft 9 in 2980 mm 9 ft 9 in 2982 mm 9 ft 9 in Compaction Width 1500 mm 59 in 1700 mm 67 in 1700 mm 67 in Drum Offset – Optional 170 mm 6 in 170 mm 6 in 170 mm 6 in

VIBRATORY SPECIFICATIONS
Amplitude – Maximum 0.65 mm 0.026 in 0.56 mm 0.022 in 1.06 mm 0.042 in Frequency – Minimum/Maximum 42/63.3 Hz – 2,520/3,800 vpm 53.3/63.3 Hz – 3200/3800 vpm 42/63.3 Hz – 2520/3800 vpm Centrifugal Force – Maximum 78.3 kN 17,603 lbF 78.3 kN 17,603 lbF 128.9 kN 28,977 lbF

SERVICE REFILL CAPACITIES
Fuel Tank Capacity 208 L 55 gal 208 L 55 gal 208 L 55 gal Water Tank Capacity 742 L 196 gal 742 L 196 gal 837 L 221 gal CB13 CB15 CB16
ENGINE
Gross Power 106 kW 144 mhp 142 hp 106 kW 144 mhp 142 hp 106 kW 144 mhp 142 hp

MACHINE WEIGHT
Operating Weight with ROPS 12 500 kg 27,557 lb 13 135 kg 28,958 lb 14 488 kg 31,941 lb Operating Weight – Maximum 13 150 kg 28,991 lb 13 785 kg 30,391 lb 15 538 kg 34,255 lb Static Linear Load 33 kg/cm 184 lb/in 32 kg/cm 181 lb/in 36 kg/cm 204 lb/in

DIMENSIONS
Overall Length 4742 mm 15 ft 6 in 4742 mm 15 ft 6 in 4742 mm 15 ft 6 in Overall Width 2325 mm 92 in 2325 mm 92 in 2325 mm 92 in Height 3068 mm 10 ft 3068 mm 10 ft 3068 mm 10 ft
Compaction Width 2000 mm 79 in 2130 mm 84 in 2130 mm 84 in Drum Offset – Optional 170 mm 6 in 170 mm 6 in 170 mm 6 in

VIBRATORY SPECIFICATIONS
Amplitude – Maximum 0.096 mm 0.038 in 1.03 mm 0.041 in 1.03 mm 0.041 in Frequency – Minumum/Maximum 42/63.3 Hz – 2520/3800 vpm 42/63.3 Hz – 2520/3800 vpm 42/63.3 Hz – 2520/3800 vpm Centrifugal Force – Maximum 110 kN 24,728 lbF 138 kN 31,069 lbF 138 kN 31,069 lbF

SERVICE REFILL CAPACITIES
Fuel Tank Capacity 250 L 66 gal 250 L 66 gal 250 L 66 gal Water Tank Capacity 1000 L 264 gal 1000 L 264 gal 1000 L 264 gal

TECHNICAL SPECIFICATIONS
See cat.com for complete specifications.

R
For more complete information on Cat products, dealer services and industry solutions, visit us on the web at www.cat.com © 2018 Caterpillar. All Rights Reserved.

VisionLink is a trademark of Trimble Navigation Limited, registered in the United States and in other countries.

Materials and specifications are subject to change without notice. Featured machines in photos may include additional equipment. See your Cat dealer for available options.

CAT, CATERPILLAR, BUILT FOR IT, their respective logos, “Caterpillar Yellow,” the “Power Edge” trade dress as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission. www.cat.com www.caterpillar.com
QEDQ2418-01 (06/18)

BACKING YOU EVERY DAY
Buy from Caterpillar and you’re buying more than just a piece of equipment. You’re also buying into a service and support operation that no competitor can match. Every Cat dealer knows that all you care about is your machine being there when you need to use it; downtime is not an option. That’s why we have the industry’s best and most reliable dealer network, bringing you the tools, technologies and know-how to keep your machine
productive and efficient.

CAT® FINANCIAL
Cat® Financial is structured to meet your needs.

Because we understand paving, we can offer
better approval rates, more flexible terms and
payments, and solutions that suit you and your
business.

SERVICE AND SUPPORT

WITH ACCU-TRAK ™

WHEEL ASSIST
Packed with technology, yet surprisingly simple to operate, the 480Xi WA harnesses the power and productivity of much larger, self-propelled reclaimers into a very powerful, versatile and affordable loader attachment. Powered by the latest Cummins intercooled turbo-diesel Tier 4 Final Performance Series engine, the 480Xi WA will pulverize up to 12-inch-thick asphalt in a single pass. The innovative upgrades and improvements throughout this new-generation Asphalt Zipper dramatically improve production in thicker asphalt, reliability and longevity of the machine, and ease of use. Full road repairs, base stabilization, street patches, and opening utility trenches in asphalt are just a few of its many uses.

LOADER MOUNT
4' Cutting Width
Reclaimer/Stabilizer
and Utility Trencher
with PATENTED Dual-Frame ZipTec™ Enhanced Pulverizing System and Accu-Trak™ Wheel Assist
480
Shown with optional
150 gallon Wheel Assist Mount
water supply system

Hydraulically activated autoadjusting clutch, remote engage, and loader operator’s safety stop
Improved Z-Pro™ X cutter head
for greater production with better
material gradation
Heavier-duty planetary/gear box
for even greater durability
Hardox®-reinforced steel frames
with greater internal abrasion resistance,
for longer life
Hydraulic safety-chain system
ensures secure connection to host vehicle
Full-range depth adjustment,
independent of the loader
Automatic hydraulic belt
tensioning that is dynamically selfadjusting and releases tension when not in use, for greater longevity
Wireless control box for cab of
host vehicle for quicker, more convenient
installation and disconnection, with
improved display
Improved bucket clamping system
for an easier, more secure connection to an
even wider range of loader buckets
Push cooling for lower under-hood
temperatures
Innovative liquid cooling jacket
for up to 5 improved planetary cooling
Quick-Load™ guiding system on all
custom trailers, for easier loading
And much more …
Integrated ZipTec™
Enhanced Pulverizing System,
with full depth range, contained grinding
chamber, and an adjustable baffle for
controlling material size
Milling sled
for easier leveling
Upgraded control panel and
wireless remote with expanded
functionality
Improved Accu-Trak™ Wheel Assist
system with remote-control steering, for even
more precise maneuvering and fine control of
milling depth, enabling use with smaller host
vehicles
Smart cylinders—
improved depth control that is
independently adjustable for
more precise milling
150 gallon wheel assist mount water supply
system (optional) for an on-board, steady supply of water Hydraulically secured top
hatch with automatic latching
and overload protection
Completely Re-engineered, with New Features and Improvements Throughout Powerful Cummins Tier 4 Final
Performance Series engine for quieter,
cleaner power

Specifications
Model 480Xi-215H WA 480Xi-260H WA
Engine Cummins
215 hp
Turbo-Diesel
Tier 4 Final
Performance Series
Cummins
260 hp
Turbo-Diesel
Tier 4 Final
Performance Series
Torque 670 ft·lb
—
908 N·m
730 ft·lb
—
990 N·m
Weight 13,800 lbs —
6260 kg
13,850 lbs —
6282 kg
Cutting
Width
48 inches (42, 36, 30, 24 inches available)
— 1219 mm (1067, 914, 762, 610 mm available)
Cutting
Depth
0 to 12 inches —
0 to 305 mm
Standard Features
Cutter
Head
Z-Pro™ X
Cutting
Bits
Double-carbide, bullet-head
Containment
System
Dual-Frame ZipTec™
Enhanced Pulverizing System
with active-hydraulic rear
baffle
Planetary Fairfield Magnum-duty
Depth
Control
Hydraulic (infinitely adjustable)
Bit Hatch Hydraulically powered,
top access, with hydraulic shock
absorption
Rear
Baffle
Infinitely adjustable, activehydraulic, remote-controlled Mounting
System
Versa-Mount™
Universal Coupler with chain
tensioning system
Controls
and
Monitoring
• Control Panel (on machine)
• Wireless Control Box
(for host vehicle)
• Wireless Remote Control
(for groundsman)
Transport Tows behind 1½-ton pickup on
tandem-axle trailer.

Additional
Features
• Accu-Trak™ Wheel Assist
• Built-in spray system
• Hydraulic belt tensioning
• Planetary cooling jacket
• Push fan under-hood cooling
Available Options
Side Shift and Tilt
Optional Mounting Systems:
• Quick Coupler
• Versa-Mount™ Quick Coupler
Water Supply Systems:
• Wheel Assist Mount (150 gallon)
Custom Trailer
Toll-free: 888-ZIPPER-8 (947-7378)
310 West 700 South, Pleasant Grove, UT 84062
Main: 801-847-3200 • Fax: 801-847-3250
AsphaltZipper.com
Asphalt Zipper reserves the right to change specifications at any time. U.S. patent nos. 7036252, 7066555, 7144087, 8177456, 10086867. Other U.S. and international patents pending. 224
Custom tandem-axle trailer (optional)
with quick-load guiding system, low center of
gravity, convenient working deck, and built-in
custom toolbox enables the 480Xi WA to be
hauled behind a 1½-ton pickup truck.

NEW Wireless
Control Box with
E-Stop and tachometer
gives host vehicle
operator control over
select Zipper functions.

CB 5

COUNCIL AGENDA ITEM
February 10, 2026
TO: Mayor and City Council
FROM: Joe Barragan, Public Works Director
SUBJECT: Authorization to Release a Request for Proposal (RFP) for Water and Wastewater Rate Study
BACKGROUND/ DISCUSSION:

On October 28, 2025, the City Council considered options for water and wastewater rates. The decision was differed pending further review. Evaluation of the current rate structure and fiscal distress of the City indicates that new, third party established and Proposition 218 compliant rates must be established for the City. Staff intends to release and RFP for a qualified vendor to create the study and present it for appropriate adoption.

The industry standard is to perform comprehensive rate studies every three to five years; our last study was started in 2021 but was never adopted. The last adopted rate study was in 2014. In 2020, the City temporarily reduced rates for water and wastewater to promote water conservation and address concerns from some members of the public. These lower rates were only anticipated to be in effect for six months until the new rate study was completed and adopted. However, the new rate study has not been adopted. This has resulted in an annualized revenue loss of approximately $1.75 million to $2.23 million for the Water Division and $490,000 for the Wastewater Division; not including prison closure. Including the prison closure both divisions have had a revenue loss of $13,000,000 and $3,100,000 respectively, from the time the rates were lowered in 2020 until today. This translates into increased rates the longer short falls are allowed to persist and increased project costs from standard inflation rates. At a rate of 5% per year for construction costs this translates into a 25% increase to project costs. Meaning less is able to be done with the same amount of money allocated if the project had been done earlier. This is also before taking into account increased repair costs for delayed projects due to outdated funding projections and implementation. The longer the delay in approving a rate study continues the larger the rate increases will be in the future and the less will get done due to higher costs. Resulting in higher repair costs due to system age and condition as well as higher standard rates due to water loss.

Which leads to a higher rate for a longer period of time the longer improperly set rate is allowed to continue. The previous presentation on the topic is attached to this staff report.

The scope of the RFP would include:

I. NEW WATER AND SEWER RATE STUDY
a. RATE SETTING STUDIES

CB 5
i. Financial Planning
ii. Demand Projections
iii. Revenue Analysis
iv. Operation and Maintenance Expenses
v. Capital Improvement Funding
vi. Reserve Funding
vii. Cash Flow Projections and Revenue Requirements
viii. Cost of Service Analysis
ix. Functionalized Cost Allocation to Customer Classes
x. Develop Water Rates
xi. Develop Sewer Rates
xii. Evaluate Impacts
xiii. Comparison Survey
xiv. Conduct Sensitivity Analysis
xv. Rate Study Report

1. Respond to any written objections from property owners based on AB 2257 (Government Code Sections 53759.1)
xvi. Rate Implementation

1. Attend Public Meetings

2. Respond to questions from the City Council and Public b. WATER/SEWER CAPACITY FEES
i. Cost of Service Study
ii. Analysis to include the current system value and newly planned capital expenses to 2030
c. DISADVANTAGED COMMUNITY STATUS
i. Proposition 1 Funding Opportunities
II. WAGE AND SALARY STUDY FOR THE WATER AND WASTEWATER SYSTEMS a. Compare Salaries to those of Similarly Sized Utilities by:
i. The Ownership
ii. Population Size
iii. Number of Employees
iv. Job Title
v. Job Duties
b. Reference salary range minimum, mid-point, and maximum levels for each position as well as 50th percentile and company-weighted average pay c. Compare similar jobs, even if you use different titles d. Review recent changes to overall staffing levels, workplace policies, and costcontrol initiatives e. Reference segmented data for all participants, water-only participants, as well as water- and wastewater-participants.

FISCAL IMPACT:

None with this action. The contract with the selected vendor will return to the City Council for approval.

CB 5
RECOMMENDATION:

Authorize the release of an RFP for a water and wastewater rate study.

ATTACHMENTS:

Previous Rate Setting Presentation

WATER AND

WASTEWATER

RATE STUDY

DISCUSSION

NEED FOR

WASTEWATER RATE
STUDY

IMPLEMENTATION

1. End of Equipment Life Cycle

2. Increased Tertiary Treatment Costs

3. Significant General Fund Costs For Recycled
Water Usage.

4. Reduced Costs With New Configuration

5. Ability To Accept Sludge and Increase Revenue
2

END OF EQUIPMENT

LIFE CYCLE
3

INCREASED

EXPENSES
Costs to operate the tertiary system have increased. Chlorine cots have tripled.

Laboratory costs have gone up 10x
Recycled Water Charges
Compliance Difficulties and violations
Upgrade capacity and replacing equipment

INCREASED

CAPABILITIES AND NEW

OPPORTUNITIES

WITHOUT TERTIARY DISCHARGE WE
CAN:
5 1. Operate with a lower license level

2. Take sludge trucks as an additional revenue stream

3. Reduction of extremely burdensome regulations

4. Save around 10% on the budget annually

5. Can get flows of 1.5 mgd

WHY A RATE

INCREASE IS NEEDED

FOR THE WATER
SYSTEM.

Water Losses
Lack of Water Pressure for Fighting Fires
Steel Pipes that have Failed
Down to Three Active Wells
New Regulations and Codes
6

WATER LOSSES

LACK OF WATER

PRESSURE FOR

FIGHTING FIRES
The Fire Department needs more pressure
and flow to fight fires in the first community.

STEEL PIPES THAT

HAVE FAILED
Total Miles of Water Lines 310
173 miles of Steel Pipes
Over 99% of Steel Pipes are in the First Community
Current Cost for Replacement
9

DOWN TO THREE

ACTIVE WELLS
Well 3 and Well 10 are currently offline. Well 16 needs to be switched to the Transmission Line
10

NEW REGULATIONS AND CODES
Regulations related to Water
Conservation:
• Limiting water usage
• Reducing water losses to 3 to 5
percent
• Water Reports
• Lead and Copper Inventory and
eventual replacement
Cross-Connection Prevention:
• New CA Cross-Connection Policy
Handbook
• Implementing Cross-Connection
Control Plan for the City
• Cross-Connection Control Specialist
• City’s Backflow Prevention
Assemblies
11

FINAL TAKEAWAYS
The Water and Wastewater rates were lower in 2020,
temporarily, which was only supposed to last for six months while the new water rate study was completed.
• The current temporary rates are not sustainable.

Water Standy Fee (WSF)
• The WSF was reduced and has now been eliminated.
• The loss in funds to the water system is approximately $500,000 per year, which now needs to be made up by
rate payers.

Reduced Staff
• The water department has not increased the number of
employees working in the department since the rates were temporarily reduced.

1. 30% Water Losses

2. 15 PSI on Barron

3. 172 miles of Pipe to
replace

4. Only three Active Wells

5. Water Conservation
and Cross-connection
Plan
12

THANK YOU
Joe Barragan
760-373-7162
[email protected]
www. californiacity-ca.gov

NB 1
4908-7847-4125 v1

COUNCIL AGENDA ITEM
February 10, 2026
TO: Mayor and City Council
FROM: Joe Barragan, Public Works Director
SUBJECT: A Resolution Approving the Remaining Community Benefit Funds to Be Used for the Existing Site Lights at the Major/ Little League Field BACKGROUND/ DISCUSSION:

The City received a donation from Bellefield 2/AES Green Energy Corp for $2.7 million. This donation was to benefit the community of California City (Community Benefit Fund). The City has used some of the funds for the purchase of emergency vehicles, the T-Bar Ceiling at City Hall, Security Camera System at the PW Yard, new HVAC units at the PD, helmets for PD, gas masks for PD, Thermal Imaging Cameras, SCBA Fill Station, and liability insurance.

On November 25, 2024, the City Council approved the repair of the existing field lights at the Major/Minor Little League Field a project appropriate for the funds. Currently, there is $267,744 left in the fund. Staff seeks City Council direction to use the funds to fix the existing field lights at the Major/Minor Little League Fields on CCB.

FISCAL IMPACT:
$267,744 to be paid from the Community Benefit Fund (60-6000-752).

RECOMMENDATION:

Staff recommends that the City Council approve the resolution authorizing City staff to use the remaining funds from the Community Benefit Fund to fix the existing field lights at the Major/Minor Little League Field.

ATTACHMENTS:

Community Benefit Fund Expenses
Resolution 26-3210

RESOLUTION NO. 26-3210
4916-6759-3101 v1 Page 1 of 2

A RESOLUTION OF THE CITY COUNCIL OF THE CITY OF

CALIFORNIA CITY APPROVING THE REMAINING COMMUNITY

BENEFIT FUNDS TO BE USED FOR THE EXISTING SITE LIGHTS AT

THE MAJOR/MINOR LITTLE LEAGUE FIELD
The City Council of the City of California City (hereafter referred to as the “City”) does resolve as follows:

WHEREAS, the City has received a donation from Bellefield 2/AES Green Energy Corp for 2.7 million dollars; and
WHEREAS, this donation was to benefit the community of California City (Community Benefit Fund); and
WHEREAS, there is $267,744 left in the fund after previously approved projects have been completed; and
WHEREAS, the existing field lights at the Major/Minor Little League Field on California City Boulevard are in need of repair.

NOW, THEREFORE BE IT RESOLVED, DETERMINED, AND ORDERED BY THE CITY COUNCIL OF THE CITY OF CALIFORNIA CITY, CALIFORNIA, AS FOLLOWS:

SECTION 1: The above recitals are true and correct and incorporated by this reference.

SECTION 2. The City Council hereby authorizes City staff to use the remaining funds from the Community Benefit Fund , in the amount of $267,744, to fix the existing field lights at the Mayor/Minor Little League Field.

SECTION 3. The Interim City Manager is authorized to execute any contracts necessary to facilitate the repairs authorized in this Resolution.

SECTION 4: The City Clerk shall certify to the passage and adoption of this Resolution.

PASSED, APPROVED, AND ADOPTED by the City Council of the City of California City, this 10th day of February 2026.
__________________________
Marquette Hawkins
Mayor

RESOLUTION NO. 26-3210
4916-6759-3101 v1 Page 2 of 2

ATTEST: APPROVED AS TO FORM:
___________________________ __________________________
Leanndrea Weible Victor M. Ponto,
Acting City Clerk City Attorney

CERTIFICATION
I, Leanndrea Weible, Interim City Clerk of the City of California City, California, hereby certify that the foregoing resolution was duly adopted at a meeting of the City Council of said City at its meeting held on the 10TH of February 2026, by the following vote, to wit:

AYES:

NOES:

ABSENT:

ABSTAIN:

IN WITNESS WHEREOF, I have hereunto set my hand and affixed the official seal of the City of California City, California, this 10th day of February 2026.

__________________________
Leanndrea Weible
Acting City Clerk

Bellefield 2 / AES Green Energy Corp
Community Benefit Funding Donation $2.7MM
Restricted Donations Expense
Anticipated GL Dept Qty Asset ID Description Budgeted Cost Actual Cost Diff 60-6000-752 Parks 1 601 Replace site lights on Major/minor league field 95,000.00 $ - 95,000.00 60-6000-752 Parks 1 602 New Site light lights at Softball Little League Field 175,000.00 $ - 175,000.00 60-6000-752 Parks 1 603 New Site lights at Junior little league field 175,000.00 $ 6,565.00 168,435.00 60-6000-752 PW 1 604 Site lights at Public Works yard 125,000.00 $ 22,035.00 102,965.00 60-6000-752 PW 1 605 Security Camera system at Public Works 25,000.00 $ 20,315.00 4,685.00 60-6000-752 PW 1 606 Commercial grade forklift (used) 60,000.00 $ - 60,000.00 60-6000-752 Planning 1 607 Ford Ranger truck 45,000.00 $ 46,021.83 (1,021.83) 60-6000-752 City Hall 1 608 Security Camera system at City Hall 25,000.00 $ - 25,000.00 60-6000-752 City Hall 1 609 Covered Solar Parking at City Hall 58,000.00 $ - 58,000.00 60-6000-752 City Hall 1 610 Flooring 10,000.00 $ - 10,000.00 60-6000-752 City Hall 1 611 Ceiling tile replacement 150,000.00 $ 7,018.87 142,981.13 60-6000-752 CE 2 612 Ford Ranger Truck with graphics and amber light package 100,000.00 $ 101,184.96 (1,184.96) 60-6000-752 PD 1 613 Housing 220,000.00 $ - 220,000.00
60-6000-752 PD 1 614 Air Conditioning 95,000.00 $ 77,700.00 17,300.00 60-6000-752 PD 2 615 Ford F150 Pursuit package w/ graphics and upfit 160,000.00 $ 164,803.85 (4,803.85) 60-6000-752 PD 2 616 Ford Expeditions Pursuit Package w/ graphics and upfit 180,000.00 $ 179,640.11 359.89 60-6000-752 PD 3 617 Ford Explorers Pursuit package w/ graphics and upfit 228,000.00 $ 228,780.60 (780.60) 60-6000-752 PD 30 618 Badge redesign to reflect California City 7,000.00 $ 2,232.52 4,767.48 60-6000-752 PD 15 619 Helmets 10,000.00 $ 8,162.56 1,837.44 60-6000-752 PD 15 620 Gas masks 6,000.00 $ 5,517.06 482.94 60-6000-752 FD 1 621 Fire Training tower 650,000.00 $ - 650,000.00 60-6000-752 FD 2 622 Thermal Imaging Cameras 21,000.00 $ 20,002.12 997.88 60-6000-752 FD 1 623 SCBA Fill Station 60,000.00 $ 59,052.39 947.61 60-6000-752 FD 4 624 Radios 20,000.00 $ 9,852.35 10,147.65 60-6000-752 City Hall 1 625 George Peterson Liability Insurance - $ 1,473,372.23 Totals 2,700,000.00 $ 2,432,256.45 267,743.55
E:\Cal City Flashdrive\Staff Report\2026\02-10-2026\Bellefield Donations\2.7M Donation Reconciliation Bellefield 1/27/202610:21 AM