11'-9 3
4 "
6'-3 916 "
0"
3"
9 3
16 "
8"
7 4
1 3 6
8 9
5 6
4 6'-3 116 "
Inside Angle
Power inputs show for 120 V
Installation, for 240 only lower input
will be present and joined with conduit
between upper and lower section.
THE CONCEPTS EXPRESSED AND DETAILS SHOWN ON THIS
DRAWING ARE CONFIDENTIAL AND PROPRIETARY. DO NOT
REPRODUCE BY ANY MEANS WITHOUT THE EXPRESS
WRITTEN CONSENT OF VANTAGE LED OR ITS WHOLLY
OWNED SUBSIDIARIES. COPYRIGHT 2022 VANTAGE LED.
GENERAL NOTES
1. REFER TO INSTALLATION MANUAL FOR
ADDITIONAL INSTALLATION.
2. REMOVAL OF FASTENERS, WELDING TO
ANY AREA OTHER THAN MOUNTING
ANGLES, DRILLING HOLES INTO THE
CABINET OR SECURING OTHER MATERIALS
DIRECTLY TO THE DISPLAY CABINET WILL
VOID WARRANTY COVERAGE.
3. USE ONLY THE HORIZONTAL OR VERTICAL
MOUNTING ANGLES/SQUARE TUBES TO
MOUNT THE DISPLAY DIRECTLY TO THE
MOUNTING STRUCTURE. ALL
INSTALLATIONS, MOUNTING STRUCTURE
DESIGNS AND CONNECTIONS MUST BE
DESIGNED / APPROVED BY A QUALIFIED
STRUCTURAL ENGINEER.
4. DUE TO STRENGTH LIMITATION OF DISPLAY
SUBSTRUCTURE, LARGER DISPLAYS WILL
REQUIRE MULTIPLE DISPLAY SECTIONS.
DISPLAY SECTION SIZE WILL BE OPTIMIZED
FOR PRODUCTION AND SHIPPING AND MAY
VARY WITH EACH DISPLAY.
5. DO NOT BLOCK THE INTAKE OR EXHAUST
VENTS ON THE BACK OF THE DISPLAY
WITH ANY PART OF STRUCTURE.
6. THE LED DISPLAY(S) ARE REAR
VENTILATED. TO MAINTAIN WARRANTY
COVERAGE, AIR MUST BE ALLOWED TO
FLOW UNOBSTRUCTED TO AND FROM ALL
DISPLAY AIR VENTS. AIR DUCTS AND
ADDITIONAL FANS MAY BE REQUIRED TO
PROVIDE AN ACTIVE EXCHANGE OF
OUTSIDE AIR TO THE DISPLAY. THIS
INCLUDES VENTS AND CHANNELS AROUND
THE FACE, THROUGH STRUCTURES THE
DISPLAY IS MOUNTED IN OR WRAPS
AROUND THE DISPLAY.
7. ALLOW A MINIMUM OF 3" BEHIND THE
DISPLAY AND 6" TO 8" WHEN MOUNTED
BACK TO BACK. FOR WALL
INSTALLATIONS, ADD 1" FOR EVERY 10
FEET OF SIGN LENGTH.
8. OPEN VENTILATION SPACE IS REQUIRED
ON THE TOP, BOTTOM AND SIDES OF THE
MOUNTING STRUCTURE. 4 FEET OF LINEAR
SPACE IS REQUIRED PER 10 FEET OF SIGN
LENGTH FOR THE TOP AND BOTTOM. THIS
MUST BE EVENLY SPACED (SEE DIAGRAM
IN INSTALLATION GUIDE)
9. ALLOW A MINIMUM OF 2" AROUND CABINET
WHEN INSTALLING WITH OTHER SIGNS OR
STRUCTURES AND 5" BEHIND THE DISPLAY
FOR RECESSED PROJECTS.
10. AMBIENT AIR TEMPERATURE IN AND
AROUND DISPLAY MUST BE BETWEEN -22 F
AND 120 F TO AVOID DAMAGING THE
DISPLAY COMPONENTS.
11. VANTAGE LED IS NOT RESPONSIBLE FOR
THE MAIN ELECTRICAL DISCONNECT.
12. DESIGN AND DIMENSIONS ARE SUBJECT
TO CHANGE WITHOUT NOTICE.
13. ANY FEATURES NOT DIMENSIONED ARE
NOT CRITICAL TO DESIGN OF MOUNTING
STRUCTURES.
14. DISPLAY FINISH IS BLACK
MOUNTING ANGLE
2 3
VENTILATION INTAKE(s)
VENTILATION EXHAUST(s)
1 4
5 6
7 8
9 12
11 10
COMMUNICATIONS,CONDUIT FITTING,90 ELBOW CABINET CONNECTOR PLATES POWER,CONDUIT FITTING, 90 ELBOW
DATA INTERCONNECT, CONDUIT FITTING, 90 ELBOW
3/4" PICK POINT MOUNTS FOR LIFTING EYES
SQUARE TUBE BRACING - TYP. 2" x 2" x 3/8"
240 VOLT AC
20 AMP
MAX.
AMP LOAD
CIRCUITS
PER FACE
APPROXIMATE WEIGHT PER FACE:
8.3 20 AMP
16.6 2
1 BREAKER
SIZE
120 VOLT AC
INPUT
VOLTAGE
REFER TO ORDER DOCUMENTS FOR INPUT VOLTAGE
MODEL:
FILE:
SCALE: DATE:
DRAWN BY: STATUS:
PAGE:
SIZE:
856 LBS.
Outdoor 10mm RGB 192x360
SD-G6-8-15-STD-10-RGB-192x360-1920-3600-127-F-R-O-A3
1:30 A 8/23/2022
K. Carnes Production
GENERAL DISPLAY | SHEET 1 OF 1
POWER REQUIREMENTS PER FACE
FEATURES LISTED IN GREEN ARE
MODEL DEPENDENT AND MAY NOT
BE REQUIRED
FEATURE
IDENTIFICATION