Emeryville City Council
June 18, 2024

RESOLUTION NO. 24-80
Resolution Of The City Council Of The City Of Emeryville Authorizing The City Manager To Execute A Contract For The Purchase Of Two Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Fire Engines For Fire Department Usage In Emeryville From Golden State Fire Apparatus For An Amount Not To Exceed $2,325,104
WHEREAS, the City is responsible for the replacement of fire apparatus as needed and has created a Vehicle Replacement Program to establish a routine life span for vehicles that are required for ongoing fire and medical protection operations in the City; and WHEREAS, the City needs to replace two fire engines because they are near their endof-life expectancy and orders take four years to be fulfilled; and WHEREAS, the City of Emeryville owns all of the fire apparatus stationed in the City, and, pursuant to the fire services contract with Alameda County Fire Department (ACFD), ACFD maintains the City' s fire apparatus fleet; and
WHEREAS, ACFD routinely reviews the condition of the City' s fleet to ensure the safety and reliability of the fire apparatus used when firefighters respond to emergency incidents and have recommended that both fire engines be replaced; and WHEREAS, under the Emeryville Municipal Code, the City is exempt from undertaking a formal bid process for the purchase of this equipment if the City “piggybacks” on another state agency’s bid process such as Sourcewell’s Cooperative Purchasing Agreement with the State of California; and
WHEREAS, staff recommends that the two replacement fire engines be purchased through Pierce Manufacturing/Golden Gate Fire Apparatus in order to ensure that the units are built and outfitted to the standard specifications of the other apparatus in the ACFD fleet; now, therefore, be it
RESOLVED, by the City Council of the City of Emeryville that the City Manager is authorized to execute a contract for the purchase of two Pierce Manufacturing, Inc.

Enforcer 1500 GPM Type 1 Fire Engines for the City’s Fire Department from Golden State Fire Apparatus for an amount not to exceed $2,325,104.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 Resolution No. 24-80
Fire Engine Purchase
City Council Meeting | June 18, 2024

ADOPTED, by the City Council of the City of Emeryville at a regular meeting held Tuesday, June 18, 2024, by the following vote:

AYES: 5
Mayor Welch, Vice Mayor Mourra and Council Members Bauters, Kaur and Priforce
NOES: 0
ABSTAIN: 0
ABSENT: 0
MAYOR
ATTEST: APPROVED AS TO FORM:

CITY CLERK SPECIAL COUNSEL

ATTACHMENTS
 Exhibit A – Purchase and Sale contract including proposal package DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 DEPUTY

CALIFORNIA

PURCHASE AND SALE CONTRACT BETWEEN CITY OF

EMERYVILLE AND GOLDEN STATE FIRE APPARATUS

FOR CITY USE ONLY
Contract No. CIP No.

Resolution No. Project No. REV02/2024
THIS PURCHASE AND SALE CONTRACT (“Contract”) is entered by and between THE CITY OF EMERYVILLE, a municipal corporation, (“City”) and GOLDEN STATE FIRE APPARATUS INC., a California corporation (“Seller” or “GSFA”), individually referred to as a “Party” and collectively as the “Parties”. This Contract shall be effective on the date it becomes fully executed by the Parties hereto (“Effective Date”).

WITNESSETH THAT
WHEREAS, the City desires to purchase from GSFA, and GSFA desires to sell to the City, two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines; and WHEREAS, the City finds that GSFA possesses specialized knowledge, skills, and experience as a supplier of fire apparatus and equipment to local agencies in Central and Northern California, and such knowledge, skills, and experience are necessary to carry out the obligations contemplated under this Contract; and WHEREAS, the City has determined that GSFA also specializes in the sales of fire apparatus and equipment manufactured by Pierce Manufacturing, Inc.; and WHEREAS, the City has determined that the products and services contemplated in this Contract are only available from a single source; and WHEREAS, the public interest will be served by this Contract; and NOW, THEREFORE, the Parties hereto do mutually agree as follows:

1. PRODUCT DESCRIPTION, PURCHASE AND SALE OF PRODUCTS, AND

TERMINATION DATE

1.1 Description of Products, Warranties, and Dealer Supplied Products/Services
The City shall purchase from GSFA, and GSFA shall sell to the City, two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines (the “Products”), as described in the Proposal, attached hereto as Exhibit A. The Products shall conform to the Product Specifications in Exhibit B of the Proposal. Warranties for the Products are set forth and shall be governed by Exhibit C of the Proposal. Dealer Supplied Products/Services are identified and defined by Exhibit D of the Proposal. The Proposal and the exhibits attached thereto are incorporated by reference. There shall be no substitutions of products or services without the prior written authorization of the City. 












 DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville | Purchase and Sale Contract REV02/2024

1.2 Purchase and Sale
The City’s purchase, and GSFA’s sale, of the Products shall be subject to and governed by the terms, conditions, and specifications set forth herein, and the terms, conditions, and specifications in the Proposal, attached hereto as Exhibit A, which is incorporated by reference. To the extent there is a conflict between the Proposal, and the terms, conditions, and specifications set forth herein, the terms, conditions, and specifications set forth herein shall govern.

1.3 Termination Date
The termination date of this Contract shall be the earlier of twelve (12) months after the delivery or pick up of the Products or five (5) years from the Effective Date.

2. CHANGE ORDERS

2.1 Change Orders
The City reserves the right to order changes in the Products (“Change Order”) by altering, adding to or deducting from the Proposal. All such changes shall be incorporated in amendments executed by GSFA and the City. Such amendments shall specify the changes ordered and any necessary adjustment of compensation and completion time and shall comply with the requirements in Section 8.a of the Proposal.

The City shall be responsible for any balance due as a result of any Change Order so long as the Maximum Amount allowed to be paid under this Contract, as set forth and defined in Section 3.2 below is not exceeded. For any Change Order that will cause the amount paid by the City to GSFA to exceed the Maximum Amount, GSFA will notify the City in writing and the Parties shall negotiate in good faith to determine responsibility for the amount in excess of the Maximum Amount. The City may increase the Maximum Amount subject to approval by Emeryville City Council and memorialization in a written amendment executed by both Parties. GSFA shall not implement such Change Order until the City has approved the increase to the Maximum Amount and the Parties have executed an amendment reflecting same.

2.2 Additions or Changes
Any additions or changes to this Contract or to the Proposal shall be by an amendment executed under all the applicable conditions of this Contract. No claim for additional compensation or extension of time shall be recognized unless contained in an amendment duly executed on behalf of the City and the Seller.

2.3 City Manager Execution
The City Manager has authority to execute without further action of the Emeryville City Council, any number of amendments so long as their total effect does not materially alter the terms of this Contract or exceed the Maximum Amount, as set forth and defined in Section 3.2 below.













 DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville | Purchase and Sale Contract REV02/2024

3. PURCHASE PRICE AND MAXIMUM AMOUNT OF COMPENSATION

3.1 Purchase Price
The purchase price for the Products shall be TWO MILLION THREE HUNDRED TWENTY FIVE THOUSAND ONE HUNDRED FOUR DOLLARS and no/100 DOLLARS ($2,325,104.00) (“Purchase Price”). Such Purchase Price includes all applicable discounts, sales taxes, fees, and bonds. The Purchase Price may be subject to adjustments or updates as set forth in Section 3.2 below.

The City agrees to pay the Purchase Price to GSFA for the Products no later than the time of delivery or pickup of the Products. All invoices for payment must be transmitted to the City no later than (20) twenty calendar days before the time of delivery or pickup.

The Purchase Price is payable in U.S. dollars.

3.2 Maximum Compensation Amount and Adjustments
The Maximum Amount allowed to be paid under this Contract is TWO MILLION THREE HUNDRED EIGHTY-FIVE THOUSAND DOLLARS AND NO CENTS ($2,385,000.00).

The City’s payment(s) to GSFA under this Contract shall not exceed the Maximum Amount.

The Parties acknowledge and agree if the Producer Price Index of Components for Manufacturing [www.bls.gov Series ID: WPUID6112] (“PPI”) has increased at a compounded annual growth rate of five percent (5.0%) or more, as measured between the month Pierce Manufacturing, Inc. accepts the order for the Products (“Order Month”) and the month that is fourteen (14) months prior to the then-current estimated Product completion date (“Evaluation Month”), then the Purchase Price may be updated in an amount equal to the increase in PPI over 5.0% for each year or fractional year between the Order Month and the Evaluation Month. GSFA shall document any such updated price for the City’s written approval before proceeding and provide an option to the City to cancel its order for the Products and terminate this Contract.

The City shall be responsible for the cost of state sales tax associated with, or attributable to, the Products. The taxes stated in the Proposal are subject to adjustment for the applicable state sales tax rate in effect at the time of delivery. Therefore, the sales tax set forth on the Proposal is only an estimate of such taxes and will be increased or decreased at the time of delivery if a change in the applicable sales tax rate has occurred, in which case the City shall pay GSFA (or be refunded by GSFA) the difference in the applicable sales tax.

For any increase or adjustment that will cause the amount paid by the City to GSFA to exceed the Maximum Amount, GSFA will notify the City in writing. The City may increase the Maximum Amount subject to approval by Emeryville City Council and memorialization in a written amendment executed by both Parties. 












 DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville | Purchase and Sale Contract REV02/2024

4. COVENANTS OF SELLER

4.1 Indemnification
To the fullest extent permitted by law, Seller shall indemnify, defend, and hold harmless City and City’s members, officers, agents, employees and volunteers, from and against any and all claims, losses, liabilities of every kind, nature and description, damages, injury (including without limitation injury to or death of an employee of Seller or subcontractors as well as any claim by any employee, agent, or independent contractor hired or employed by Seller that such persons or individuals are entitled to any benefit otherwise provided to employees of the City, including coverage under the California Public Employee Retirement System), costs and expenses of any kind, whether actual, alleged or threatened, including, without limitation, incidental and consequential damages, court costs, reasonable attorneys’ fees, litigation expenses, and fees of expert contractors or expert witnesses (“Damages”) incurred in connection therewith and the costs of investigation, arising out of, pertaining to, or relating to, directly or indirectly, in whole or in part, GSFA’s breach of the Contract and/or the negligence, recklessness, or willful misconduct of GSFA, any subcontractor, anyone directly or indirectly employed by them or anyone that they control. This indemnification obligation is not limited in any way by any limitation on the amount or type of damages or compensation payable to or for Seller.

If Seller’s obligation to defend, indemnify, and/or hold harmless arises out of Seller’s performance of “design professional” services (as that term is defined under Civil Code section 2782.8), then, and only to the extent required by Civil Code section 2782.8, which is fully incorporated herein, Seller’s indemnification obligation shall be limited to claims that arise out of, pertain to, or relate to the negligence, recklessness, or willful misconduct of the Seller, and, upon Seller obtaining a final adjudication by a court of competent jurisdiction, Seller’s liability for such claim, including the cost to defend, shall not exceed the Seller’s proportionate percentage of fault.

The City shall indemnify, defend, and hold harmless GSFA, its agents, servants, successors and assigns from and against any Damages to the extent such Damages arise out of or in connection with: (i) the City’s breach of the Contract, or (ii) the City’s use, storage, or operation of the Products following delivery, regardless of where, how, and by whom operated (excluding any negligent operation by GSFA).

The indemnification and assumptions of liability and obligations herein provided shall continue in full force and effect notwithstanding the termination of the Contract, whether by expiration of time, by operation of law or otherwise. This Section is not intended to and shall not constitute the exclusive remedy of the Parties under the Contract; the Parties may seek indemnity from one another under other legal principles, whether based in equity or law, so long as they do not nullify or cancel the effects of this Section. 












 DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville | Purchase and Sale Contract REV02/2024

4.2 Independent Contractor
The Seller hereby covenants and declares that it is engaged in an independent business and agrees to perform its obligations under this Contract as an independent contractor and not as the agent or employee of the City. The Seller agrees to be solely responsible for its own matters relating to the time and place its obligations are performed; the instrumentalities, tools, supplies and/or materials necessary to complete its obligations; hiring of contractors, agents or employees to complete its obligations; and the payment of employees, including compliance with Social Security, withholding and all other regulations governing such matters. The Seller agrees to be solely responsible for its own acts and those of its subordinates and employees during the term of this Contract. Nothing herein shall be construed to create a partnership or joint venture between the City and Seller.

4.3 Insurance
Seller shall not perform any of its obligations under this Contract until it has provided evidence satisfactory to the City that it has secured all insurance required under Exhibit B: “Product Specifications” of the Proposal, attached hereto and incorporated herein by reference.

4.4 Records, Reports and Audits

4.4.1 Records

1. Records shall be established and maintained by the Seller in accordance with requirements prescribed by the City with respect to all matters covered by this Contract. Except as otherwise authorized, such records shall be maintained for a period of three years from the date that final payment is made under this Contract.

Furthermore, records that are the subject of audit findings shall be retained for three years or until such audit findings have been resolved, whichever is later.

2. All costs shall be supported by properly executed payrolls, time records, invoices, contracts, or vouchers, or other official documentation evidencing in proper detail the nature and propriety of the charges. All checks, payrolls, invoices, contracts, vouchers, orders or other accounting documents pertaining in whole or in part to this Contract shall be clearly identified and readily accessible.

4.4.2 Reports and Information
Upon request, the Seller shall furnish to the City any and all statements, records, reports, data and information related to matters covered by this Contract in the form requested by the City.













 DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville | Purchase and Sale Contract REV02/2024

4.4.3 Audits and Inspections
At any time during normal business hours and as often as the City may deem necessary, there shall be made available to the City for examination all records with respect to all matters covered by this Contract. The Seller will permit the City to audit, examine, and make excerpts or transcripts from such records, and to audit all contracts, invoices, materials, payrolls, records of personnel, conditions of employment and or data relating to all matters covered by this Contract.

4.5 Conflicts of Interest
The Seller covenants and declares that, other than this Contract, it has no holdings or interests within the City of Emeryville, nor business holdings, contracts or agreements with any official, employee or other representative of the City. For the duration of this Contract, in the event the Seller or its principals, agents or employees acquire such a holding, interest, contract, or agreement within the City of Emeryville or with any official, employee or representative of the City in the future, the Seller will immediately notify the City of such holding, interest, contract, or agreement in writing.

4.6 Discrimination Prohibited
The Seller covenants and agrees that in performing its obligations under this Contract, the Seller shall not discriminate against any person on the basis of race, color, religion, sex, sexual orientation, gender identity, marital status, national origin or ancestry, age or disability, except as provided in section 12940 of the Government Code.

4.7 Licenses, Certifications and Permits
The Seller covenants and declares that it has obtained all diplomas, certificates, licenses, permits or the like required of the Seller by any and all national, state, regional, county, city or local boards, agencies, commissions, committees or other regulatory bodies in order to perform its obligations under this Contract. All work performed by Seller under this Contract shall be in accordance with applicable legal requirements and shall meet the standard of quality ordinarily expected of competent professionals.

4.8 Authority to Contract
The Seller covenants and declares that it has obtained all necessary approvals of its board of directors, stockholders, general partners, limited partners or similar authorities to simultaneously execute and bind Seller to the terms of this Contract, if applicable.

4.9 California Labor Requirements

4.9.1 Prevailing Wage Requirements
Seller is aware of the requirements of California Labor Code Sections 1720 et seq. and 1770 et seq., which require the payment of prevailing wage rates and the performance of other requirements on certain “public works” and “maintenance” projects (“Prevailing Wage Laws”). If the Seller’s obligations are being performed as part of an applicable “public works” or “maintenance” project, as defined by the Prevailing Wage Laws, and if the total compensation is $1,000 or more, Seller agrees to fully comply with such 












 DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville | Purchase and Sale Contract REV02/2024

Prevailing Wage Laws. Seller shall defend, indemnify and hold the City, its officials, officers, employees and agents free and harmless from any claims, liabilities, costs, penalties or interest arising out of any failure or alleged failure to comply with the Prevailing Wage Laws. It shall be mandatory upon the Seller and all subcontractors to comply with all California Labor Code provisions, which include but are not limited to prevailing wages (Labor Code Sections 1771, 1774 and 1775), employment of apprentices (Labor Code Section 1777.5), certified payroll records (Labor Code Sections 1771.4 and 1776), hours of labor (Labor Code Sections 1813 and 1815) and debarment of contractors and subcontractors (Labor Code Section 1777.1). The requirement to submit certified payroll records directly to the Labor Commissioner under Labor Code section 1771.4 shall not apply to work performed on a public works project that is exempt pursuant to the small project exemption specified in Labor Code Section 1771.4.

4.9.2 Registration
If the Seller’s obligations are being performed as part of an applicable “public works” or “maintenance” project, then pursuant to Labor Code Sections 1725.5 and 1771.1, the Seller and all subcontractors performing such obligations must be registered with the Department of Industrial Relations. Seller shall maintain registration for the duration of the Contract and require the same of any subcontractors, as applicable.

Notwithstanding the foregoing, the contractor registration requirements mandated by Labor Code Sections 1725.5 and 1771.1 shall not apply to work performed on a public works project that is exempt pursuant to the small project exemption specified in Labor Code Sections 1725.5 and 1771.1.

4.9.3 Labor Compliance Oversight
This Contract may also be subject to compliance monitoring and enforcement by the Department of Industrial Relations. It shall be Seller’s sole responsibility to comply with all applicable registration and labor compliance requirements. Any stop orders issued by the Department of Industrial Relations against Seller or any subcontractor that affect Seller’s performance of Services, including any delay, shall be Seller’s sole responsibility. Any delay arising out of or resulting from such stop orders shall be considered Seller caused delay and shall not be compensable by the City. Seller shall defend, indemnify and hold the City, its officials, officers, employees and agents free and harmless from any claim or liability arising out of stop orders issued by the Department of Industrial Relations against Seller or any subcontractor.

4.9.4 Workers’ Compensation
Pursuant to the requirements of section 1860 of the California Labor Code, Seller will be required to secure the payment of workers’ compensation to his employees in accordance with the provisions of section 3700 of the Labor Code. By signing this Contract, Seller certifies the following:
“I am aware of the provisions of section 3700 of the California Labor Code which require every employer to be insured against liability for workers’ compensation or to undertake 












 DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville | Purchase and Sale Contract REV02/2024

self-insurance in accordance with the provisions of that code, and I will comply with such provisions before commencing the performance of the work of this contract.”

4.9.5 Event of Default
Failure by Seller to comply with any provision of this Section shall constitute an Event of Default and shall be grounds for termination as provided in this Contract.

5. TERMINATION

5.1 By City
City may terminate a Product order identified in the Proposal or terminate a Change Order by providing written notice to GSFA in accordance with Section 13 below. If the City elects to terminate a Product order, the City shall pay GSFA a cancellation fee as follows: (a) after the Product order is accepted and entered by GSFA, 10% of the portion of the Purchase Price applicable to such Product (including all associated taxes, fees and costs) (such amount, the “Product Price”); (b) after completion of the preconstruction phase of the order process, 20% of the Product Price; and (c) after the requisition of any materials or commencement of any manufacturing or assembly of the Product by either GSFA or Pierce Manufacturing Inc. (“Manufacturer”), 50% of the Product Price.

If the applicable tier of cancellation fee is not sufficient to cover all actual costs and fees incurred by GSFA with Manufacturer in connection with the City’s termination of the Product order (“Manufacturer Termination Fees”), then in addition to such cancellation fee the City shall pay the balance of all Manufacturer Termination Fees. The tier of cancellation fee applicable to any cancellation, as well as the determination of whether a Product has reached substantial completion, shall be at the discretion of GSFA with input from the City. The City may request a fee waiver, and GSFA, in its sole discretion, may agree to waive and/or adjust such fee. GSFA will return the balance of the Purchase Price or Product Price, as applicable, within thirty (30) calendar days of the effective date of the cancellation of the Product order or termination of the Contract.

The City may terminate the Contract for an Event of Default by GSFA (as defined in Section 6 below) after providing GSFA with written notice in accordance with Section 13 below (which notice shall describe with reasonably particularity the Event of Default justifying such termination) and if such Event of Default remains uncured (if capable of cure) thirty (30) calendar days following GSFA’s receipt of such notice; provided, however, that the foregoing cure period shall continue if and for so long as GSFA has commenced and is continuing to undertake commercially reasonable efforts to cure such Event of Default as promptly as reasonably practicable.

5.2 By GSFA
GSFA may terminate the Contract for an Event of Default (as defined in Section 6 below) by the City after providing the City with written notice in accordance with Section 












 DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville | Purchase and Sale Contract REV02/2024

13 (which notice shall describe with reasonably particularity the Event of Default justifying such termination) and if such Event of Default remains uncured (if capable of cure) thirty (30) calendar days following the City’s receipt of such notice; provided, however, that the foregoing cure period shall continue if and for so long as the City has commenced and is continuing to undertake commercially reasonable efforts to cure such Event of Default as promptly as reasonably practicable. Notwithstanding the foregoing, GSFA may terminate the Contract effective immediately upon written notice to the City for the City’s failure to pay any amount owed under the Contract when due.

Notwithstanding any other provision in the Contract, if the City terminates a Product order in accordance with Section 5.1 above, GSFA may elect to instead terminate the Contract upon notice to the City in accordance with Section 13 below; but upon such termination of the Contract by GSFA, the City shall not be liable for any cancellation fees for any Product(s).

5.3 Based on Discontinuation or Cancellation by Manufacturer.

In the event that Manufacturer cancels a Product order (provided that such cancellation is not the result of an act by the City in violation of the Contract) or discontinues the manufacture of a Product prior to its completion and delivery: (i) if such Product is the only Product contemplated under the Contract, then the Contract shall terminate; or (ii) if additional Products are contemplated under the Contract, then only the Product order for the applicable cancelled or discontinued Product shall be terminated. Such Contract termination or Product termination, as applicable, shall be effective upon GSFA’s written notice to the City of such cancellation or discontinuance in accordance with Section 13 below. GSFA’s only obligation to the City in such event shall be the return of any prepayment paid by the City for the cancelled or discontinued Product. For the avoidance of doubt, the cancellation fees contemplated in Section 5.1 above shall not apply in the event of a termination pursuant to this Section 5.3.

6. EVENT OF DEFAULT
The occurrence of one or more of the following events (each, an “Event of Default”) shall constitute a default under the Contract: (a) the City’s failure to pay any amounts due or to perform any of its obligations under the Contract; (b) GSFA’s failure to perform any of its obligations under the Contract; (c) either Party becoming insolvent or becoming subject to bankruptcy or insolvency proceedings; (d) any representation made by either Party under the Contract which is false in any material respect; or (e) any other material breach of the terms of the Contract by a Party.

7. NO PERSONAL LIABILITY
No member, official or employee of the City shall be personally liable to the Seller or any successor in interest in the event of any default or breach by the City or for any amount which may become due to the Seller or successor or on any obligation under the terms of this Contract.













 DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville | Purchase and Sale Contract REV02/2024

8. ENTIRE AGREEMENT
This Contract and its exhibits constitute the complete agreement between the Parties and supersedes any and all other agreements, either oral or in writing, between the Parties with respect to the subject matter of this Contract. No other agreement, statement or promise relating to the subject matter of this Contract not contained in this Contract shall be valid or binding. This Contract may be modified or amended only by a written document signed by representatives of both Parties with appropriate authorization.

9. SUCCESSORS AND ASSIGNS
Subject to the provisions of this Contract regarding assignment, this Contract shall be binding on the heirs, executors, administrators, successors and assigns of the respective Parties.

10. APPLICABLE LAW AND ATTORNEY’S FEES; VENUE
If any action at law or in equity is brought to enforce or interpret the provisions of this Contract, the rules, regulations, statutes and laws of the State of California will control.

The prevailing party shall be entitled to reasonable attorney's fees in addition to any other relief to which said party may be entitled. The exclusive venue for any legal action taken pursuant to this Contract shall be the State of California Superior Court for the County of Alameda or the United States District Court for the Northern District of California

11. SEVERABILITY
The caption or headnote on articles or sections of this Contract are intended for convenience and reference purposes only and in no way define, limit or describe the scope or intent thereof, or of this Contract nor in any way affect this Contract. Should any article(s) or section(s), or any part thereof, later be deemed unenforceable by a court of competent jurisdiction, the remainder of this Contract shall remain in full force and effect to the extent possible.

12. BUSINESS TAX CERTIFICATE
Prior to commencement of the Services to be provided hereunder, Seller shall apply to the City of Emeryville Finance Department for a business tax certificate, pay the applicable business tax and maintain said business tax certificate during the term of this Contract, as provided in Article 1 of Chapter 1 of Title 3 of the Emeryville Municipal Code.

13. NOTICES
Any notices, requests, consents, claims, demands, waivers and other communications required or permitted to be given under this Contract and/or the Proposal must be given in writing at the address of each Party set forth below, or to such other address as either 












 DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville | Purchase and Sale Contract REV02/2024

Party may substitute by written notice to the other in accordance with this Section 13, by one of the following methods: hand delivery; registered, express, or certified mail, return receipt requested, postage prepaid; or nationally recognized private express courier. All such communications will be deemed to have been given: (i) when delivered by hand (with written confirmation of receipt); (ii) on the third (3rd) calendar day after the date mailed, by registered, express or certified mail; or (iii) when delivered by the addressee if sent by a nationally recognized private express courier.

GSFA:

Golden State Fire Apparatus Inc.
7400 Reese Road
Sacramento, CA 95828
Attn: Ryan Wright, President
Phone No: 209-330-1638
E-Mail: [email protected]
CITY OF EMERYVILLE:

Pedro Jimenez
Assistant City Manager
City of Emeryville
1333 Park Avenue
Emeryville, CA 94608
Phone No: 510-596-3770
E-Mail: [email protected]
With copy to:

John I. Kennedy
City Attorney
City of Emeryville
1333 Park Avenue
Emeryville, CA 94608
Phone No: 510-596-4381
E-Mail:

[email protected]

14. COUNTERPARTS
This Contract may be signed in counterparts, each of which shall constitute an original. It is expressly agreed that each Party to this Contract shall be bound by its own telecopied, scanned, electronic or digital signature and shall accept the telecopied, scanned, electronic or digital signature of the other Party to this Contract.

15. NO THIRD-PARTY BENEFICIARIES
Except to the extent expressly provided for herein, there are no intended third-party beneficiaries of any right or obligation assumed by the Parties.

16. NON-EXCLUSIVITY
City reserves right to employ other contractors in connection with the products and services covered under this Contract.













 DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville | Purchase and Sale Contract REV02/2024

17. ASSIGNMENT OR TRANSFER
Neither Party shall assign, hypothecate or transfer, either directly or by operation of law, this Contract or any rights, obligations, or interests herein without the prior written consent of the other Party. Any attempt to do so shall be null and void, and any assignees, hypothecates or transferees shall acquire no right or interest by reason of such attempted assignment, hypothecation or transfer.

18. WAIVER
The City’s failure to enforce any provision of this Contract or the waiver in a particular instance shall not be construed as a general waiver of any future breach or default.

SIGNATURES ON FOLLOWING PAGE













 DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville | Purchase and Sale Contract REV02/2024

19. SIGNATURE PAGE TO PURCHASE AND SALE CONTRACT
IN WITNESS WHEREOF the City and the Seller have executed this Contract, which shall become effective on the date it becomes fully executed by the Parties hereto .

Approved As To Form:

City Attorney
Dated: CITY OF EMERYVILLE
City Manager
Dated: GOLDEN STATE FIRE APPARATUS INC.
(Signature)
Ryan Wright, President
Attach:

W-9 Form
Attach:

Business License Certificate














  
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 PREPARED ESPECIALLY FOR:

CITY OF EMERYVILLE
Two (2) Pierce Manufacturing, Inc.

Enforcer 1500 GPM Type 1 Engines

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 Proposal
Standard Terms and Conditions (Exhibit A)
Product Specifications (Exhibit B)
▪ Supporting Documents (If Applicable)
◦ Electrical Analysis
◦ Turning Radius Report
Product Warranties (Exhibit C)
Dealer Supplied Products and/or Services (Exhibit D)

TABLE OF CONTENTS
1 2
3 4
5 goldenstatefire.com
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 JROGHQVWDWHĆUHFRP
1 PROPOSAL
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 goldenstatefire.com
7400 Reese Road, Sacramento, CA 95828 | 916.330.1638
PRODUCT PROPOSAL FOR:

City of Emeryville 1333 Park Avenue
Emeryville, CA 94608
Sales Consultant
Mike Martinez
[email protected]
Mobile: (916) 704-7755
Golden State Fire Apparatus, Inc. (“GSFA”) is pleased to provide this proposal for the fire apparatus(es) and equipment identified below (the "Product”) to CITY OF EMERYVILLE (“Customer”) for consideration. This proposal (this “Proposal”) includes the following exhibits attached hereto: the Terms and Conditions attached as Exhibit A (the “Terms and Conditions”); the Product Specifications attached as Exhibit B (the “Specifications”); the Product Warranties attached as Exhibit C; and the Dealer Supplied Products and/or Services attached as Exhibit D (the “Dealer Supplied Products/Services List”). This Proposal and its exhibits are intended to serve as “EXHIBIT A” to the PURCHASE AND SALE CONTRACT BETWEEN CITY OF EMERYVILLE AND GOLDEN STATE FIRE APPARATUS (“Contract”).

PAYMENT TERMS – Customer shall pay the total purchase price set forth directly above (the “Grand Total Purchase Price”) to GSFA no later than the time of GSFA’s delivery of the applicable Product to Customer’s address listed above (or Customer’s pick up of such Product at GSFA’s facilities, if approved by GSFA). GSFA shall have no obligation to deliver, or permit pick up of the Product if the Customer does not have full payment ready when the Product is complete and ready to deliver or pick up, as applicable. Customer shall pay any balance due as a result of Change Orders as described in the Terms and Conditions.

MANUFACTURER – Customer acknowledges that GSFA is not an agent of the Product manufacturer identified above (“Manufacturer”) and is not capable of binding Manufacturer. Within five (5) business days of the Effective Date of the Contract, GSFA shall submit an order form to the Manufacturer for the Product. GSFA’s further performance under the Contract is contingent upon Manufacturer’s acceptance of such order form at the price and on the terms GSFA believed to be available when submitting this Proposal to Customer. If Manufacturer rejects such order as submitted or fails to respond to GSFA within a reasonable amount of time, GSFA shall notify Customer in writing, and unless GSFA and Customer otherwise agree in writing, the Contract shall then terminate and have no further force or effect.

SUBMITTED DATE EXPIRATION DATE GSFA PROPOSAL # MANUFACTURER BID # MANUFACTURER CONSORTIUM 03/27/2024 06/30/2024 50327-24B 973 Pierce
Manufacturing,
Inc.

Sourcewell #113021-
PMI, ID #259,
Member #163847

ITEM PRODUCT DESCRIPTION EXTENDED PRICE
A Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 2,215,670.00 B Discount for Sourcewell Consortium Purchase (116,670.00) C SUBTOTAL 2,099,000.00
D 10.50% State Sales Tax 220,395.00
E California Tire Fee 21.00
F 100% Performance Bond 5,688.00
G GRAND TOTAL PURCHASE PRICE 2,325,104.00
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 goldenstatefire.com
7400 Reese Road, Sacramento, CA 95828 | 916.330.1638
PRODUCT COMPLETION – The Product shall be ready for final inspection by Customer at the manufacturing facility within approximately 46.5 to 49.5 MONTHS after the Effective Date. The foregoing estimate is provided as a good faith approximation as of the date of submission of this Proposal and is subject to the Terms and Conditions.

PREDELIVERY SERVICE – If applicable, after transportation from the manufacturing facility and prior to final delivery or pick up, the Product shall receive those additional Products and/or services identified on the Dealer Supplied Products/Services List. It is estimated that such a service will add approximately 0.5 to 1 MONTH(S) to the above Product completion estimate. The foregoing estimate is provided as a good faith approximation as of the date of submission of this Product Proposal and is subject to the Terms and Conditions.

PROPOSAL EXPIRATION – This Proposal supersedes any previous proposal(s) presented to Customer by GSFA.

PURCHASE ORDER – Any PO shall be made out to: Golden State Fire Apparatus, Inc. – 7400 Reese Road – Sacramento, CA 95828.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 JROGHQVWDWHĆUHFRP

STANDARD TERMS

AND CONDITIONS
Exhibit “A”
2 DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 1 TERMS AND CONDITIONS

1. Definitions.
a. “Customer” means the City of Emeryville.
b. “Contract” has the meaning given in the Proposal.
c. “Dealer Preparation,” if applicable, means additional product(s) and/or services added by GSFA after Manufacturer’s completion of the Products and prior to delivery, in accordance with the Dealer Supplied Products/Services List.
d. “Delivery Date” means the Product Completion timeframe plus the Predelivery Service timeframe equals the Delivery Date.
e. “Dealer Supplied Products/Services List” means the Dealer Supplied Products and/or Services List attached to the Proposal as Exhibit D, which reflects all Dealer Preparation under the Contract absent a valid Change Order(s).
f. “Effective Date” has the meaning given in the Contract. g. “Grand Total Purchase Price” means the total purchase price for the Products identified in the Proposal (subject to any adjustments required or permitted by these Terms and Conditions, including by the execution of a valid Change Order(s)).
h. “GSFA” means Golden State Fire Apparatus, Inc., a California corporation. i. “Manufacturer” means Pierce Manufacturing Inc., the corporation identified in the Proposal as responsible for manufacturing the Products.
j. “Party” or “Parties” means GSFA and/or Customer, as applicable. k. “Predelivery Service” means the Products and/or Services that will be provided by GSFA after transportation of the Product(s) from the manufacturing facility and prior to Final Delivery or Pick-Up. l. “Products” means the fire apparatus(es) and any associated equipment listed in the Proposal and further described in the Specifications.
m. “Product Completion” means the fire apparatus(es) in the Proposal and further described in the Specifications being ready for final inspection by Customer at the manufacturing facility. n. “Proposal” means the GSFA proposal to which these Terms and Conditions are attached. o. “Product Warranties” means the Manufacturer warranties for the Products attached to the Proposal as Exhibit C.
p. “Specifications” means the specifications for the Products attached to the Proposal as Exhibit B. q. “Terms and Conditions” means these Terms and Conditions, which are attached to the Proposal as Exhibit A.

2. Purchase and Payment.
a. Purchase. Customer agrees to purchase the Products at the Grand Total Purchase Price (as such amount may be adjusted in accordance with these Terms and Conditions), pursuant to the payment terms set forth in the Contract.
b. Contingency Reserve Fund. The Grand Total Purchase Price may include an amount to be set aside for the purpose of funding any future costs or financial obligations incurred by Customer under the Proposal or any valid Change Order(s) (the “Contingency Reserve Fund”). If applicable, the amount of any required Contingency Reserve Fund will be set forth in either the Proposal or Exhibit D. The Contingency Reserve Fund may be withdrawn against by Customer or GSFA for the purpose of satisfying Customer’s payment obligations under the initial Proposal or any valid Change Order(s) (including, without limitation, a Change Order submitted by GSFA pursuant to Section 8.b). If a Contingency Reserve Fund is required, the amount of such fund is not intended as an estimate of the actual additional costs of contingencies, Change Orders, unforeseen items or other required work that may be incurred under the Contract after submission of the Proposal to Customer, which amounts Customer acknowledges may exceed the Contingency Reserve Fund amount.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 2 The balance of any Contingency Reserve Fund will be credited against Customer’s payment obligations, or otherwise returned to Customer within thirty (30) calendar days of delivery of all Products under the Contract (provided that Customer has paid all amounts owed under the Contract as of such date). c. [RESERVED]
d. [RESERVED]

3. Product Completion Date. Within thirty (30) calendar days of the Effective Date, GSFA shall submit to Customer a tentative Product completion date (which may differ from the Product completion estimate contained in the Product Proposal). Due to global supply chain constraints, any Product completion date contained herein, or in the Product Proposal, or otherwise provided to Customer, is a good faith estimate only as of the date provided to Customer, and merely an approximation based on current information available to GSFA and Manufacturer. GSFA shall have no liability to Customer for a failure by GSFA or Manufacturer to meet any such good faith estimate. All Product completion estimates are subject to modification and, if applicable, GSFA will provide updates to such good faith estimates to Customer when available.

4. [RESERVED]

5. Multiple Unit Purchase. If the Grand Total Purchase Price includes pricing for multiple Products, the Product price stated in the Proposal shall only be valid if the quantity of Products being proposed are purchased at the same time, pursuant to the same purchase agreement/contract. GSFA shall have no obligation to offer the same price for any Product if purchased by Customer pursuant to a later purchase agreement/contract.

6. Late Fee; Storage Fee. It is the responsibility of the Customer to have any outstanding balance due, paid in full to GSFA, prior to or at the time that the Product is complete and ready to deliver. If payment is late or delivery is delayed pending payment, a daily finance charge of $150.00 and a daily storage fee of $50.00 may apply until such payment is received.

7. Delivery; Inspection and Acceptance.
a. Delivery. Subject to Section 3 above, the Products are scheduled to be delivered to the location and within the time period specified in the Proposal. Such delivery date is a good faith estimate, and GSFA is, notwithstanding this Section 7.a, not bound to such date unless it otherwise agrees in a separate writing to complete delivery by a date certain. For the avoidance of doubt, GSFA is not responsible for delivery delays caused by or because of actions, omissions or conduct of Customer, the Manufacturer, or their respective employees, affiliates, suppliers, contractors, and carriers. Risk of loss for the Productsshall pass to Customer at the point and time of delivery (which shall include an attempted delivery by GSFA which cannot be completed due to any act of Customer). However, title to the Products shall only pass to Customer upon delivery if Customer has then fully paid GSFA all amounts due hereunder (including additional amounts due under any valid Change Order). Absent GSFA’s separate written agreement, which it may or may not provide in itssole and absolute discretion, delivery ofthe Products will not occur before Customer has fully paid all amounts due under the Contract and provided proof of insurance reasonably satisfactory to GSFA. If GSFA permits Customer to take possession of the Products, Customer may not mount equipment, conduct training, or place the Products into service until all amounts due under the Contract have been paid. If Customer has ordered multiple Products, GSFA reserves the right to deliver such Products in installments and to separately invoice Customer for such Products.
b. Inspection and Acceptance. Upon delivery, Customer shall have ten (10) calendar days within which to inspect the Products for substantial conformance to the Specifications, and in the event of substantial nonconformance to the Specifications to furnish GSFA with written notice sufficient to permit GSFA to evaluate such non-conformance (“Notice of Nonconformance to Specifications”). Contingent upon part availability and Customer’s cooperation, any Product not in substantial conformance to material Specificationsshall be remedied by GSFA (by repair or replacement, at GSFA’s election) within thirty (30) calendar daysfrom GSFA’sreceipt ofthe Notice of Nonconformance to Specifications. In the event GSFA does not receive a Notice of Nonconformance to DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 3 Specifications within ten (10) calendar days of delivery, the Products will be deemed to be in conformance with Specifications and accepted by Customer.

8. Changes to Contract or Proposal.
a. Change Orders. The Customer may request that GSFA incorporate a change to the Products or the Specifications for the Products, or GSFA may submit changesto the Contract required or permitted to be made by GSFA (pursuant to Section 8.b below or otherwise) by delivering a written Change Order to the other party hereto, which shall include a description of the proposed change sufficient to permit the receiving party to evaluate such change (either, a “Change Order”). For any Change Order submitted by Customer, GSFA will provide Customer a written response (a “Response”) stating (i) whether GSFA will accommodate such Change Order (which GSFA may decide in its sole and absolute discretion); and (ii) the terms of the modification to the order, including any increase or decrease in the Grand Total Purchase Price resulting from such Change Order, a date on which any increase in the Grand Total Purchase Price must be paid, and an estimate of any effect on production scheduling or delivery resulting from such Change Order. Customer shall have seven (7) calendar days after receipt of the Response to notify GSFA as to whether Customer desires to make the changes GSFA has approved in the Response.

In the event Customer countersigns GSFA’s Response, the countersigned response shall be deemed a written amendment to the Contract and this Proposal. Customer shall pay the increase (or be refunded the decrease) in the Grand Total Purchase Price by the date specified in the Response. b. Additional Changes.
i. Component Price Volatility; Increases Imposed by Manufacturer. GSFA shall not be responsible for (i) any unforeseen price increase or surcharge enacted by suppliers of major components of the Products (including but not limited to commercial chassis, engine, transmission, and fire pump); or (ii) price increasesimposed on GSFA by Manufacturer pursuant to Manufacturer’sterms and conditionsforsale ofthe Product (a “Manufacturer Price Increase”), after Customer becomes bound by the Contract. Except where such price increase causes the total amount to be paid by the Customer to GSFA to exceed the Maximum Amount (as such term is defined in the Contract), Customer shall be responsible for all amounts arising from any price increases for major components of the Products (including all associated taxes and fees thereon) for the Products or any Manufacturer Price Increases occurring after the execution of the Contract which increases the cost of the Products to GSFA, and such amounts will be documented on a Change Order adjusting the Grand Total Purchase Price accordingly. Any price increase that will cause the amount paid by Customer to GSFA to exceed the Maximum Amount shall be governed by Section

3.2 of the Contract.

A Manufacturer Price Increase may include, but shall not be limited to, an increase in Product price resulting from an increase in the Producer Price Index of Components for Manufacturing (see www.bls.gov Series ID:

WPUID6112) in excess of a compounded annual growth rate of five percent (5%), as measured between the month Manufacturer acceptsthe applicable Product order and the month that isfourteen (14) months priorto the then-current estimated Product completion date (the foregoing, a “PPI-Based Price Increase”). If, upon Customer’s receipt of a Change Orderreflecting a PPI-Based Price Increase, Customer electsto terminate the applicable Product Orderin accordance with Section 8.b.iii below rather than pay such increase, then the cancellation fees described in Section 5.1 of the Contract shall apply. ii. New Legal Standards. In the event the Product design, materials or specifications require an alteration arising from new regulations issued by any governmental entity or trade association, including, but not limited to, the NFPA, DOT, and EPA, and such alteration increases the cost of the Products to GSFA, Customer shall be responsible for changes to the Grand Total Purchase Price arising from such alteration, except where such price increase causes the total amount to be paid by the Customer to GSFA to exceed the Maximum Amount (as such term is defined in the Contract). GSFA shall promptly notify Customer when it becomes aware of any potential or required change in regulations occurring prior to delivery that would impact the Products purchased. Any price increase that will cause the amount paid by Customer to GSFA to exceed the Maximum Amount shall be governed DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 4 by Section 3.2 of the Contract.
iii. Change Orders. Customershall execute any Change Ordersubmitted by GSFA documenting any ofthe changesrequired or permitted by Sections 8.b.i and 8.b.ii above (which shall, to the extent practicable, itemize any increasesin the Grant Total Purchase Price and specify a commercially reasonable date by which Customer must pay such increase), unless Customer instead elects to terminate the applicable Product order under the Contract within fifteen (15) calendar days of Customer’s receipt of such Change Order and in accordance with Section 5.1 of the Contract. Absent such a termination, failure to execute a Change Order does not alter Customer’s obligations under this Section 8.b.
c. Changes in Commercial Specifications. Specifications for all components of the Products manufactured by companies other than the Manufacturer are subject to change without notice. Specifications for such components will be as available at the time of manufacture of the Products. GSFA shall not be liable for any deviations in such specifications arising from a substitution of components or changes in the design of any component by their original manufacturer.

9. [RESERVED].

10. Customer’s Obligations. Customer shall provide its timely and best efforts to cooperate with GSFA and Manufacturer during the Product manufacturing process. Reasonable and timely cooperation includes, without limitation, Customer’s providing timely information in response to any requests from Manufacturer or GSFA. At Customer’s sole discretion, Customer’s authorized representatives may travel to Manufacturer’s facility for inspections and approval of the Products, including a final approval before any Product leaves Manufacturer’s facility.

11. Representations and Warranties. Customer hereby represents and warrants to GSFA as of the Effective Date that the execution of the Contract and the purchase of the Product(s) and performance of the other obligations of Customer under the Contract have been approved by Customer in accordance with applicable general laws and, as applicable, Customer’s charter, ordinances, purchasing policies, and other governing documents, and executed by the appropriate Customer employees, officials, and/or representatives, and funding for Customer’s performance of its obligations under the Contract has been duly budgeted and appropriated by Customer.

12. Standard Warranty. All applicable Manufacturer warranties are contained in the Product Warranties. Any additional warranties must be expressly approved in a writing signed by GSFA, and Customer acknowledges and agrees that Manufacturer will not be liable for any such additional warranties. a. [RESERVED]
b. [RESERVED]

13. [RESERVED]

14. [RESERVED]

15. Force Majeure. If a Party is totally or partially prevented from performing any of its obligations under this Contract as a result of any act of god or other event beyond the reasonable control of the affected Party(ies), including without limitation, weather, fire, flood, act of public enemy or terrorism, strike or labor dispute, pandemic or epidemic, governmental action or directive or local, regional or national day of mourning (“Force Majeure”), the affected Party shall promptly serve notice on the other Party specifying the matter(s) constituting the Force Majeure event and providing the other Party with its best estimate of the likely extent and duration of the Force Majeure event. Subject to both Parties (acting reasonably and in good faith) agreeing there has been a Force Majeure, the Party prevented from performing its obligations shall be excused performance of such obligations from the date of such notice for so long as the Force Majeure event shall continue provided that:

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 5 (i) throughout the duration of the Force Majeure event, it shall take all reasonable steps to mitigate the effects of the Force Majeure event; and
(ii) upon cessation of the Force Majeure event, it shall promptly serve notice of the other Party of such cessation.

If performance by a Party of its obligations under this Contract is only partially affected by a Force Majeure event, such Party shall nevertheless remain liable for the performance of those obligations not affected by the Force Majeure event and therefore which it can reasonably perform, save where the Parties agree otherwise.

16. [RESERVED]

17. Contradictions. In the event of a conflict between the Contract and any Change Order, or between Change Orders, the terms of the latest executed Change Order shall control.

18. Manufacturer’s Statement of Origin. It is agreed that the manufacturer’s statement of origin (“MSO”) for the Product covered by the Contract, if applicable, shall be retained and remain in the possession of GSFA per California Department of Vehicles (DMV) directives. Notwithstanding the foregoing, GSFA shall provide Customer with the original MSO if the Customer is self-registering, and Customer shall comply with all good-faith Process of Duty and other DMV requirements applicable to the Product and retain its own MSO.

19. [RESERVED]

20. [RESERVED]

21. [RESERVED]

END OF TERMS AND CONDITIONS
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 JROGHQVWDWHĆUHFRP

PRODUCT

SPECIFICATIONS
Exhibit “B”
3 DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 1 of 115
GOLDEN STATE FIRE APPARATUS, INC. is pleased to submit a proposal to City of Emeryville. The following paragraphs will describe in detail the apparatus, construction methods, and equipment proposed. This proposal will indicate size, type, model and make of components parts and equipment, providing proof of compliance with each and every item (except where noted) in the departments advertised specifications.

PIERCE MANUFACTURING was founded in 1913. Since then we have been building bodies with one philosophy, "BUILD THE FINEST". Our skilled craftsmen take pride in their work, which is reflected, in the final product. We have been building fire apparatus since the early "forties" giving Pierce Manufacturing over 75 years of experience in the fire apparatus market. Pierce Manufacturing has built and put into service more than 62,500 apparatus, including more than 33,900 on Pierce custom chassis designed and built specifically for fire and emergency applications. Our Appleton, Wisconsin facility has over 870,000 total square feet of floor space situated on approximately 105 acres of land. Our Bradenton, Florida facility has 300,000 square feet of floor space situated on approximately 38 acres of land.

Our beliefs in high ethical standards are carried through in all of our commitments and to everyone with whom we do business. Honesty, Integrity, Accountability and Citizenship are global tenets by which we all live and work. Consequently, we neither engage in, nor have we ever been convicted of price fixing, bid rigging, or collusion in any domestic or international fire apparatus market.

Pierce has only one brand of fire apparatus "Pierce", ensuring you are receiving top of the line product that meets your specification.

In accordance with the current edition of applicable NFPA standards, this proposal will specify whether the fire department, manufacturer, or apparatus dealership will provide required loose equipment.

Images and illustrative material in this proposal are as accurate as known at the time of publication, but are subject to change without notice. Images and illustrative material is for reference only, and may include optional equipment and accessories and may not include all standard equipment.

GENERAL DESIGN AND CONSTRUCTION
To control quality, ensure compatibility, and provide a single source for service and warranty, the custom cab, chassis, pump module and body will be entirely designed, assembled/welded and painted in Pierce owned manufacturing facilities. This includes, but not limited to the cab weldment, the pumphouse module assembly, the chassis assembly, the body and the electrical system.

QUALITY AND WORKMANSHIP
Pierce has set the pace for quality and workmanship in the fire apparatus field. Our tradition of building the highest quality units with craftsmen second to none has been the rule right from the beginning and we demonstrate that ongoing commitment by: Ensuring all steel welding follows American Welding Society D1.1-2004 recommendations for structural steel welding. All aluminum welding follows American Welding society and ANSI D1.2-2003 requirements for structural welding of aluminum. All sheet metal welding follows American welding Society B2.1-2000 requirements for structural welding of sheet metal. Our flux core arc welding uses alloy rods, type 7000 and is performed to American Welding Society standards A5.20-E70T1. Furthermore, all employees classified as welders are tested DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 2 of 115
and certified to meet the American welding Society codes upon hire and every three (3) years thereafter. Pierce also employs and American Welding Society certified welding inspector in plant during working hours to monitor weld quality.

Pierce Manufacturing operates a Quality Management System under the requirements of ISO 9001.

These standards sponsored by the International Organization for Standardization (ISO) specify the quality systems that are established by the manufacturer for design, manufacture, installation and service. A copy of the certificate of compliance is included with this proposal.

In addition to the Quality Management system, we also employ a Quality Achievement Supplier program to ensure the vendors and suppliers that we utilize meet the high standards we demand. That is just part of our overall "Quality at the Source" program at Pierce.

To demonstrate the quality of our products and services, a list of at least twenty five (25) fire departments/municipalities that have purchased vehicles for a second time is provided.

DELIVERY
The apparatus will be delivered under its own power to ensure proper break-in of all components while the apparatus is still under warranty. A qualified delivery representative shall deliver the apparatus and remain for a sufficient length of time to instruct personnel in proper operation, care and maintenance of the equipment delivered.

MANUAL AND SERVICE INFORMATION
At time of delivery, complete operation and maintenance manuals covering the apparatus will be provided. A permanent plate will be mounted in the driver's compartment specifying the quantity and type of fluids required including engine oil, engine coolant, transmission, pump transmission lubrication, pump primer and drive axle.

SAFETY VIDEO
At the time of delivery Pierce will also provide one (1) 39-minute, professionally produced apparatus safety video, in DVD format. This video will address key safety considerations for personnel to follow when they are driving, operating, and maintaining the apparatus, including the following: vehicle pretrip inspection, chassis operation, pump operation, aerial operation, and safety during maintenance.

PERFORMANCE TESTS
A road test will be conducted with the apparatus fully loaded and a continuous run of no less than ten (10) miles. During that time the apparatus will show no loss of power nor will it overheat. The transmission drive shaft or shafts and the axles will run quietly and be free of abnormal vibration or noise. The apparatus when fully loaded will not have less than 25 percent nor more than 50 percent on the front axle, and not less than 50 percent nor more than 75 percent on the rear axle. The apparatus will meet the current edition of applicable NFPA standards acceleration and braking requirements.

SERVICE AND WARRANTY SUPPORT
Pierce dealership support will be provided by GOLDEN STATE EMERGENCY VEHICLE SERVICE, INC. by operating in conjunction with a Pierce authorized service center. The service center will have factory-trained mechanics on staff versed in Pierce fire apparatus. The service facility will be located within one hundred (100) miles of the fire department.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 3 of 115
In addition to the dealership, Pierce has service facilities located in both, Weyauwega, Wisconsin and Bradenton, Florida. Pierce also maintains a dedicated parts facility of over 100,000 square feet in Appleton, Wisconsin. The parts facility stocks in excess of $5,000,000 in parts dedicated to service and replacement parts. The parts facility employs a staff dedicated solely for the distribution and shipment of service and replacement parts.

Service parts for the apparatus being proposed can be found via Pierceparts.com which, is an interactive online tool that delivers information regarding your specific apparatus as well as the opportunity to register for training classes.

As a Pierce customer you have the ability to view the complete bill of materials for your specific apparatus, including assembly drawings, piece part drawings, and beneficial parts notations. You will also have the ability to search the complete Pierce item master through a parts search function which offers all Pierce SKU's and descriptions offered on all Pierce apparatus. Published component catalogs, which include proprietary systems along with an extensive operator's manual library is available for easy reference.

Pierce Manufacturing maintains a dedicated service and warranty staff of over 35 personnel, dedicated to customer support, which also maintains a 24 hour 7 day a week toll free hot line, four (4) on staff EVTs, and offers hands-on repair and maintenance training classes multiple times a year.

LIABILITY
The successful bidder will defend any and all suits and assume all liability for the use of any patented process including any device or article forming a part of the apparatus or any appliance furnished under the contract.

INSURANCE PROVIDED BY BIDDER

COMMERCIAL GENERAL LIABILITY INSURANCE
The successful bidder will, during the performance of the contract and for three (3) years following acceptance of the product, keep in force at least the following minimum limits of commercial general liability insurance:

Each Occurrence$1,000,000
Products/Completed Operations Aggregate$1,000,000
Personal and Advertising Injury$1,000,000
General Aggregate$2,000,000
Coverage will be written on a Commercial General Liability form. The policy will be written on an occurrence form and will include Contractual Liability coverage for bodily injury and property damage subject to the terms and conditions of the policy. The policy will include Owner as an additional insured when required by written contract.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 4 of 115

COMMERCIAL AUTOMOBILE LIABILITY INSURANCE
The successful bidder will, during the performance of the contract, keep in force at least the following minimum limits of commercial automobile liability insurance and coverage will be written on a Commercial Automobile liability form:

Each Accident Combined Single Limit:$1,000,000

UMBRELLA/EXCESS LIABILITY INSURANCE
The successful bidder will, during the performance of the contract and for three (3) years following acceptance of the product, keep in force at least the following minimum limits of umbrella liability insurance:

Aggregate:$3,000,000
Each Occurrence:$3,000,000
The umbrella policy will be written on an occurrence basis and at a minimum provide excess to the bidder's General Liability and Automobile Liability policies.

The required limits can be provided by one (1) or more policies provided all other insurance requirements are met.

Coverage will be provided by a carrier(s) rated A- or better by A.M. Best.

All policies will provide a 30-day notice of cancellation to the named insured. The Certificate of Insurance will provide the following cancellation clause: Should any of the above described polices be cancelled before the expiration date thereof, notice will be delivered in accordance with the policy provisions.

Bidder agrees to furnish owner with a current Certificate of Insurance with the coverages listed above along with the bid. The certificate will show the purchaser as certificate holder.

INSURANCE PROVIDED BY MANUFACTURER

PRODUCT LIABILITY INSURANCE
The manufacturer will, during the performance of the contract and for three (3) years following acceptance of the product, keep in force at least the following minimum limits of Product Liability insurance:

Each Occurrence$1,000,000
Products/Completed Operations Aggregate$1,000,000
Coverage will be written on a Commercial General Liability form. The policy will be written on an occurrence form. The manufacturer's policy will include the owner as additional insured when required by written contract between the Owner and a Pierce authorized dealer.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 5 of 115

UMBRELLA/EXCESS LIABILITY INSURANCE
The manufacturer will, during the performance of the contract and for three (3) years following acceptance of the product, keep in force at least the following minimum limits of umbrella liability insurance:

Each Occurrence:$25,000,000
Aggregate:$25,000,000
The umbrella policy will be written on an occurrence basis and provide excess to the manufacturer's General Liability/Products policies.

The required limits can be provided by one (1) or more policies provided all other insurance requirements are met.

Coverage will be provided by a carrier(s) rated A- or better by A.M. Best.

All policies will provide a 30-day notice of cancellation to the named insured. The Certificate of Insurance will provide the following cancellation clause: Should any of the above described polices be cancelled before the expiration date thereof, notice will be delivered in accordance with the policy provisions.

Manufacturer agrees to furnish owner with a current Certificate of Insurance with the coverages listed above along with the bid. The certificate will show the purchaser as the certificate holder.

SINGLE SOURCE MANUFACTURER
Pierce Manufacturing, Inc. provides an integrated approach to the design and manufacture of our products that delivers superior apparatus and a dedicated support team. From our facilities, the chassis, cab weldment, cab, pumphouse (including the sheet metal enclosure, valve controls, piping and operators panel) and body will be entirely designed, tested, and hand assembled to the customer's exact specifications. The electrical system either hardwired or multiplexed, will be both designed and integrated by Pierce Manufacturing. The warranties relative to these major components (excluding component warranties such as engine, transmission, axles, pump, etc.) will be provided by Pierce as a single source manufacturer. Pierce's single source solution adds value by providing a fully engineered product that offers durability, reliability, maintainability, performance, and a high level of quality.

Your apparatus will be manufactured in Appleton, Wisconsin.

COMPARISON REPORT
A report will be provided to allow the Sales Representative to compare the options to a previous job.

The report will be provided for job 32365.

SPECIAL INSTRUCTIONS
The apparatus being proposed will be designed and built to match the 34048. However, some variation may be necessary due to changes in our manufacturing processes or our product offering. Revisions in NFPA guidelines and/or other regulations may also affect our ability to match the previous unit.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 6 of 115
NFPA 2024 STANDARDS
This unit will comply with the NFPA standards effective January 1, 2024, except for fire department directed exceptions. These exceptions will be set forth in the Statement of Exceptions.

Certification of slip resistance of all stepping, standing and walking surfaces will be supplied with delivery of the apparatus.

All horizontal surfaces designated as a standing or walking surface that are greater than 48.00" above the ground must be defined by a 1.00" wide line along its outside perimeter. Perimeter markings and designated access paths to destination points will be identified on the customer approval print and are shown as approximate. Actual location(s) will be determined based on materials used and actual conditions at final build. Access paths may pass through hose storage areas and opening or removal of covers or restraints may be required. Access paths may require the operation of devices and equipment such as the aerial device or ladder rack.

A plate that is highly visible to the driver while seated will be provided. This plate will show the overall height, length, and gross vehicle weight rating.

The manufacturer will have programs in place for training, proficiency testing and performance for any staff involved with certifications.

An official of the company will designate, in writing, who is qualified to witness and certify test results.

NFPA COMPLIANCY
Apparatus proposed by the bidder will meet the applicable requirements of the National Fire Protection Association (NFPA) as stated in current edition at time of contract execution. Fire department's specifications that differ from NFPA specifications will be indicated in the proposal as "non-NFPA".

PUMP TEST
Underwriters Laboratory (UL) will test, approved, and certify the pump. The test results and the pump manufacturer's certification of hydrostatic test; the engine manufacturer's certified brake horsepower curve; and the pump manufacturer's record of pump construction details will be forwarded to the Fire Department.

GENERATOR TEST
If the unit has a generator, Underwriters Laboratory (UL) will test, approved, and certify the generator.

The test results will be provided to the Fire Department at the time of delivery.

BREATHING AIR TEST
If the unit has breathing air, Pierce Manufacturing will draw an air sample from the air system and have the sample certified that the air quality meets the requirements of NFPA 1989, Standard on Breathing Air Quality for Fire and Emergency Services Respiratory Protection.

VEHICLE INSPECTION PROGRAM CERTIFICATION
To assure the vehicle is built to current NFPA 1900 standards, the apparatus, in its entirety, will be third-party, independent, audit-certified through Underwriters Laboratory (UL) that it is built and complies to all applicable standards in the current edition. The certification includes: all design, DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 7 of 115
production, operational, and performance testing of not only the apparatus, but those components that are installed on the apparatus.

A placard will be affixed in the driver's side area stating the third party agency, the date, the standard and the certificate number of the whole vehicle audit.

BID BOND NOT REQUESTED
A bid bond will not be included. If requested, the following will apply:

All bidders will provide a bid bond as security for the bid in the form of a 5 percent bid bond to accompany their bid. This bid bond will be issued by a Surety Company who is listed on the U.S.

Treasury Departments list of acceptable sureties as published in Department Circular 570. The bid bond will be issued by an authorized representative of the Surety Company and will be accompanied by a certified power of attorney dated on or before the date of bid. The bid bond will include language, which assures that the bidder/principal will give a bond or bonds as may be specified in the bidding or contract documents, with good and sufficient surety for the faithful performance of the contract, including the Basic One (1) Year Limited Warranty, and for the prompt payment of labor and material furnished in the prosecution of the contract.

Notwithstanding any document or assertion to the contrary, any surety bond related to the sale of a vehicle will apply only to the Basic One (1) Year Limited Warranty for such vehicle. Any surety bond related to the sale of a vehicle will not apply to any other warranties that are included within this bid (OEM or otherwise) or to the warranties (if any) of any third party of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. In the event of any contradiction or inconsistency between this provision and any other document or assertion, this provision will prevail.

PERFORMANCE BOND, 1 YEAR
The successful bidder will furnish a Performance and Payment bond (Bond) equal to 100 percent of the total contract amount within 30 days of the notice of award. Such Bond will be in a form acceptable to the Owner and issued by a surety company included within the Department of Treasury's Listing of Approved Sureties (Department Circular 570) with a minimum A.M. Best Financial Strength Rating of A and Size Category of XV. In the event of a bond issued by a surety of a lesser Size Category, a minimum Financial Strength rating of A+ is required.

Bidder and Bidder's surety agree that the Bond issued hereunder, whether expressly stated or not, also includes the surety's guarantee of the vehicle manufacturer's Basic One (1) Year Limited Warranty period included within this proposal. Owner agrees that the penal amount of this bond will be simultaneously amended to 100% percent of the total contract amount upon satisfactory acceptance and delivery of the vehicle(s) included herein. Notwithstanding anything contained within this contract to the contrary, the surety's liability for any warranties of any type will not exceed one (1) year from the date of such satisfactory acceptance and delivery, or the actual Basic One (1) Year Limited Warranty period, whichever is shorter.

Due to global supply chain constraints, any delivery date contained herein is a good faith estimate as of the date of this order/contract, and merely an approximation based on current information. Delivery updates will be made available, and a final firm delivery date will be provided as soon as possible.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 8 of 115
If the Producer Price Index of Components for Manufacturing [www.bls.gov Series ID: WPUID6112] ("PPI") has increased at a compounded annual growth rate of 5.0% or more between the month Pierce accepts the order ("Order Month") and a month 14 months prior to the then predicted Ready For Pickup date ("Evaluation Month"), then pricing may be updated in an amount equal to the increase in PPI over

5.0% for each year or fractional year between the Order Month and the Evaluation Month.

The seller will document any such updated price for the customer's approval before proceeding and provide an option to cancel the order.

APPROVAL DRAWING
A drawing of the proposed apparatus will be prepared and provided to the purchaser for approval before construction begins. The Pierce sales representative will also be provided with a copy of the same drawing. The finalized and approved drawing will become part of the contract documents. This drawing will indicate the chassis make and model, location of the lights, siren, horns, compartments, major components, etc.

A "revised" approval drawing of the apparatus will be prepared and submitted by Pierce to the purchaser showing any changes made to the approval drawing.

FINAL DRAWING
There will be a revised drawing of the truck with all the changes made during production provided at pickup.

DRAWING, CAB TOP VIEW
On the sales drawing a top view of the cab seating and EMS cabinets will be provided. The top view will be a reference only of the seating and EMS cabinets in the order.

DRAWING, COMPARTMENT LAYOUT
A basic drawing will be provided for the interior body compartments. This drawing will be provided for graphic representation only and will include such things as shelves, trays, reels, dividers, air control panels, air bottle storage bins, poly boxes & etc.

ELECTRICAL WIRING DIAGRAMS
Two (2) electrical wiring diagrams, prepared for the model of chassis and body, will be provided.

ENFORCER CHASSIS
The Pierce Enforcer™ is the custom chassis developed exclusively for the fire service. Chassis provided will be a new, tilt-type custom fire apparatus. The chassis will be manufactured in the apparatus body builder's facility eliminating any split responsibility. The chassis will be designed and manufactured for heavy-duty service, with adequate strength, capacity for the intended load to be sustained, and the type of service required. The chassis will be the manufacturer's first line tilt cab.

MAXIMUM OVERALL HEIGHT
The maximum overall height of the apparatus will be 115.50".

MAXIMUM OVERALL LENGTH
The maximum overall length of the apparatus will be 362.25".

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 9 of 115

WHEELBASE
The wheelbase of the vehicle will be 182.50".

GVW RATING
The gross vehicle weight rating will be 43,500 lbs .

FRAME
The chassis frame will be built with two (2) steel channels bolted to five (5) cross members or more, depending on other options of the apparatus. The side rails will have a 13.38" tall web over the front and mid sections of the chassis, with a continuous smooth taper to 10.75" over the rear axle. Each rail will have a section modulus of 25.992 cubic inches and a resisting bending moment (rbm) of 3,119,040 in-lb over the critical regions of the frame assembly, with a section modulus of 18.96 cubic inches with an rbm of 2,275,200 in-lb over the rear axle. The frame rails will be constructed of 120,000 psi yield strength heat-treated 0.38" thick steel with 3.50" wide flanges.

FRAME REINFORCEMENT
In addition, a mainframe internal liner will be provided. The liner will be an internal "C" design that steps to an internal "L" design over the rear axle. It will be heat-treated steel measuring 12.50" x 3.00" x 0.25" through the front portion of the liner, stepping to 9.38" x 3.00" x 0.25" through the rear portion of the liner. Each liner will have a section modulus of 13.58 cubic inches, yield strength of 110,000 psi, and rbm of 1,494,042 in-lb. Total rbm at wheelbase center will be 4,391,869 in-lb.

The frame liner will be mounted inside of the chassis frame rail and extend the full length of the frame.

FRONT NON DRIVE AXLE
The Oshkosh TAK-4® front axle will be of the independent suspension design with a ground rating of 19,500 lb.

Upper and lower control arms will be used on each side of the axle. Upper control arm castings will be made of 100,000-psi yield strength 8630 steel and the lower control arm casting will be made of 55,000-psi yield ductile iron.

The center cross members and side plates will be constructed out of 80,000-psi yield strength steel.

Each control arm will be mounted to the center section using elastomer bushings. These rubber bushings will rotate on low friction plain bearings and be lubricated for life. Each bushing will also have a flange end to absorb longitudinal impact loads, reducing noise and vibrations.

There will be nine (9) grease fittings supplied, one (1) on each control arm pivot and one (1) on the steering gear extension.

The upper control arm will be shorter than the lower arm so that wheel end geometry provides positive camber when deflected below rated load and negative camber above rated load.

Camber at load will be zero degrees for optimum tire life.

The ball joint bearing will be of low friction design and be maintenance free.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 10 of 115
Toe links that are adjustable for alignment of the wheel to the center of the chassis will be provided.

The wheel ends must have little to no bump steer when the chassis encounters a hole or obstacle.

The steering linkage will provide proper steering angles for the inside and outside wheel, based on the vehicle wheelbase.

The axle will have a turning angle of up to 45 degrees.

FRONT SUSPENSION
Front Oshkosh TAK-4™ independent suspension will be provided with a minimum ground rating of 19,500 lb.

The independent suspension system will be designed to provide maximum ride comfort. The design will allow the vehicle to travel at highway speeds over improved road surfaces and at moderate speeds over rough terrain with minimal transfer of road shock and vibration to the vehicle's crew compartment.

Each wheel will have torsion bar type spring. In addition, each front wheel end will also have energy absorbing jounce bumpers to prevent bottoming of the suspension.

The suspension design will be such that there is at least 10.00" of total wheel travel and a minimum of

3.75" before suspension bottoms.

The torsion bar anchor lock system allows for simple lean adjustments, without the use of shims. One can adjust for a lean within 15 minutes per side. Anchor adjustment design is such that it allows for ride height adjustment on each side.

The independent suspension was put through a durability test that simulated 140,000 miles of inner city driving.

FRONT SHOCK ABSORBERS
KONI heavy-duty telescoping shock absorbers will be provided on the front suspension.

FRONT OIL SEALS
Oil seals with viewing window will be provided on the front axle.

FRONT TIRES
Front tires will be Goodyear 385/65R22.5 radials, 18 ply Armor Max MSA tread, rated for 20,050 lb maximum axle load and 68 mph maximum speed.

The tires will be mounted on Alcoa 22.50" x 12.25" polished aluminum disc type wheels with a ten (10) stud, 11.25" bolt circle.

REAR AXLE
The rear axle will be a Meritor™, Model RS-24-160, with a capacity of 24,000 lb.

TOP SPEED OF VEHICLE
A rear axle ratio will be furnished to allow the vehicle to reach a top speed of 68 mph / 109 kph.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 11 of 115

REAR SUSPENSION
The rear suspension will be Standens, semi-elliptical, 3.00" wide x 52.50" long, with a ground rating of 24,000 lb. The spring hangers will be castings.

The two (2) top leaves will wrap the forward spring hanger pin, and the rear of the spring will be a slipper style end that will ride in a rear slipper hanger.

A steel encased rubber bushing will be used in the spring eye. The steel encased rubber bushing will be maintenance free and require no lubrication.

REAR OIL SEALS
Oil seals will be provided on the rear axle(s).

DRIVER CONTROL DIFFERENTIAL LOCK (DCDL)
A rear axle will be equipped with a driver controlled differential lock (DCDL).

The control will be located within easy reach of the driver. An indicator light will be provided next to the control switch.

REAR TIRES
Rear tires will be four (4) Goodyear 12R22.50 radials, load range H, Endurance RSA highway tread, rated for 27,120 lb maximum axle load and 75 mph maximum speed.

The tires will be mounted on Alcoa 22.50" x 8.25" polished aluminum disc wheels with a ten (10) stud

11.25" bolt circle.

TIRE BALANCE
All tires will be balanced with Counteract balancing beads. The beads will be inserted into the tire and eliminate the need for wheel weights.

TIRE PRESSURE MANAGEMENT
There will be a RealWheels LED AirSecure™ tire alert pressure management system provided, that will monitor each tire's pressure. A sensor will be provided on the valve stem of each tire for a total of six (6) tires.

The sensor will calibrate to the tire pressure when installed on the valve stem for pressures between 10 and 200 psi. The sensor will activate an integral battery operated LED when the pressure of that tire drops 5 to 8 psi.

Removing the cap from the sensor will indicate the functionality of the sensor and battery. If the sensor and battery are in working condition, the LED will immediately start to flash.

HUB COVERS (FRONT)
Stainless steel hub covers will be provided on the front axle.

HUB COVERS (REAR)
A pair of Realwheels, RW7715, foam mounted, stainless steel high hat hub covers will be provided on rear axle hubs.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 12 of 115

MUD FLAPS
Mud flaps with a Pierce logo will be installed behind the front and rear wheels.

WHEEL CHOCKS
There will be one (1) pair of folding Ziamatic, Model SAC-44-E, aluminum alloy, Quick-Choc wheel blocks, with easy-grip handle provided.

Wheel Chock Brackets
There will be one (1) pair of Zico, Model SQCH-44-H, horizontal mounting wheel chock brackets provided for the Ziamatic, Model SAC-44-E, folding wheel chocks. The brackets will be made of aluminum and consist of a quick release spring loaded rod to hold the wheel chocks in place. The brackets will be mounted one (1) forward and one (1) rearward of the left side rear tire.

ELECTRONIC STABILITY CONTROL
A vehicle control system will be provided as an integral part of the ABS brake system from Meritor Wabco.

The system will monitor and update the lateral acceleration of the vehicle and compare it to a critical threshold where a side roll event may occur. If the critical threshold is met, the vehicle control system will automatically reduce engine RPM, engage the engine retarder (if equipped), and selectively apply brakes to the individual wheel ends of the front and rear axles to reduce the possibility of a side roll event.

The system will monitor directional stability through a lateral accelerometer, steer angle sensor and yaw rate sensor. If spinout or drift out is detected, the vehicle control system will selectively apply brakes to the individual wheel ends of the front and rear axles to bring the vehicle back to its intended direction.

ANTI-LOCK BRAKE SYSTEM
The vehicle will be equipped with a Wabco 4S4M, anti-lock braking system. The ABS will provide a four (4) channel anti-lock braking control on both the front and rear wheels. A digitally controlled system that utilizes microprocessor technology will control the anti-lock braking system. Each wheel will be monitored by the system. When any wheel begins to lockup, a signal will be sent to the control unit. This control unit will then reduce the braking of that wheel for a fraction of a second and then reapply the brake. This anti-lock brake system will eliminate the lockup of any wheel thus helping to prevent the apparatus from skidding out of control.

AUTOMATIC TRACTION CONTROL
An anti-slip feature will be included with the ABS. The Automatic Traction Control will be used for traction in poor road and weather conditions. The Automatic Traction Control will act as an electronic differential lock that will not allow a driving wheel to spin, thereby supplying traction at all times. The ABS electronic control unit (ECU) will work with the engine ECU, sharing information concerning wheel slip. Engine ECU will use information to control engine speed, allowing only as much throttle application as required for the available traction, regardless of how much the driver is asking for. An "off road traction" switch will be provided on the instrument panel. Activation of the switch will allow additional tire slip to let the truck climb out and get on top of deep snow or mud.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 13 of 115
BRAKES
The service brake system will be full air type.

The front brakes will be Knorr/Bendix disc type with a 17.00" ventilated rotor for improved stopping distance.

The brake system will be certified, third party inspected, for improved stopping distance.

The rear brakes will be Meritor™, Disc Plus, Model EX225, disc operated with automatic slack adjusters and a 17.00" ventilated rotor for improved stopping distance.

BRAKE SYSTEM AIR COMPRESSOR
The air compressor will be a Cummins/WABCO with 18.7 cubic feet per minute output.

BRAKE SYSTEM
The brake system will include:
• Brake treadle valve
• Heated automatic moisture ejector on air dryer
• Total air system minimum capacity of 4,272 cubic inches • Two (2) air pressure gauges with a red warning light and an audible alarm, that activates when air pressure falls below 60 psi
• Spring set parking brake system
• Parking brake operated by a push-pull style control valve • A parking "brake on" indicator light on instrument panel • Park brake relay/inversion and anti-compounding valve, in conjunction with a double check valve system, with an automatic spring brake application at 40 psi • A pressure protection valve to prevent all air operated accessories from drawing air from the air system when the system pressure drops below 80 psi (550 kPa) • 1/4 turn drain valves on each air tank
The air tank will be primed and painted to meet a minimum 750 hour salt spray test.

The air tanks will be same as frame color.

To reduce the effects of corrosion, the air tank will be mounted with stainless steel brackets.

BRAKE SYSTEM AIR DRYER
The air dryer will be a Bendix AD-9 air dryer, with spin-on coalescing filter cartridge and 100 watt heater.

BRAKE LINES
Color-coded nylon brake lines will be provided. The lines will be wrapped in a heat protective loom in the chassis areas that are subject to excessive heat.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 14 of 115

AIR INLET
One (1) air inlet with a .25" male, Parker B2C, coupling will be provided. It will allow station air to be supplied to the apparatus brake system through a shoreline hose. The inlet will be located on the driver side pump panel. A check valve will be provided to prevent reverse flow of air. The inlet will discharge into the "wet" tank of the brake system. A mating female coupling will also be provided with the loose equipment.

AIR OUTLET
One (1) air outlet will be installed with a female coupling and shut off valve, located on the driver side seat riser. This system will tie into the "wet" tank of the brake system and include an 85-psi pressure protection valve in the outlet line to prevent the brake system from losing all air.

Female coupling and male fitting will be .25" thread.

A mating male fitting will be provided with the loose equipment.

AIR OUTLET SHUT OFF VALVE
A quarter turn shut off valve will be provided next to the air outlet. The shut off valve will be mounted in the same bezel as the outlet coupling.

ADDITIONAL AIR TANK FOR AIR HORN
An additional air tank with 1,454 cubic inch displacement will be provided to increase the capacity of the air system. This tank will be dedicated for air horn use.

The air tank will be primed and painted to meet a minimum 750 hour salt spray test. To reduce the effects of corrosion, the air tank will be mounted with stainless steel brackets.

The air tank(s) will be black #101.

The output flow of the engine air compressor varies with engine rpm. Full compressor output is only achieved at governed engine speed. Engine speed may be limited by generators, pumps and other PTO driven options.

ALL WHEEL LOCK-UP
An all wheel lock-up system will be installed which applies air to the front brakes and uses the spring brake at the rear. System will be operated with battery switched power and the parking brake set.

U-BOLT GUARD OVER PARKING BRAKE KNOB
There will be one (1) U-bolt type protective guard(s) installed over the "Parking Brake" knob to prevent accidental activation of the brake. The guard will be located on the driver's side.

A locking switch will be provided to help prevent accidental activation of the front wheel lock control.

MANUAL MOISTURE EJECTOR(S)
Three (3) manual moisture ejectors will be installed in the brake system.

The moisture ejector will be remote mounted on the driver side of vehicle, as close to the edge of vehicle as possible.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 15 of 115
A loop will be provided at the moisture ejector, to allow for ease of pulling the drain.

Each moisture ejector will have a label directly under the ejector, stating air tank drain.

Air lines will be routed from the air tank to the moisture ejector.

The moisture ejector(s) will be provided on the left side of the vehicle under the forward most position of the body reservoir(s).

COMPRESSION FITTINGS ONLY
Any nylon tube on the apparatus that is pneumatic will be plumbed with compression type fittings where applicable. Push lock fittings will not be acceptable for any pneumatic nylon tube plumbing.

ENGINE
The chassis will be powered by an electronically controlled engine as described below:

Make: Cummins
Model: X10
Power: 450 hp at 2100 rpm
Torque: 1650 lb-ft at 1400 rpm
Governed
Speed:
2200 rpm
Emissions Level: EPA 2027
Fuel: Diesel
Cylinders: Six (6)
Displacement: 606 cubic inches (9.9L)
Starter: Delco 39MT™
Fuel Filters: Spin-on style primary filter with water separator and water-in-fuel sensor.

Secondary spin-on style filter.

The engine will include On-board diagnostics (OBD), which provides self diagnostic and reporting. The system will give the owner or repair technician access to state of health information for various vehicle sub systems. The system will monitor vehicle systems, engine and after treatment. The system will illuminate a malfunction indicator light on the dash console if a problem is detected.

HIGH IDLE
A high idle switch will be provided, inside the cab, on the instrument panel, that will automatically maintain a preset engine rpm. A switch will be installed, at the cab instrument panel, for activation/deactivation.

The high idle will be operational only when the parking brake is on and the truck transmission is in neutral. A green indicator light will be provided, adjacent to the switch. The light will illuminate when the above conditions are met. The light will be labeled "OK to Engage High Idle." DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 16 of 115

ENGINE BRAKE
A Jacobs® engine brake is to be installed with the controls located on the instrument panel within easy reach of the driver.

The driver will be able to turn the engine brake system on/off and have a high, medium and low setting.

The engine brake will activate when the system is on and the throttle is released.

The high setting of the brake application will activate and work simultaneously with the variable geometry turbo (VGT) provided on the engine.

The engine brake will be installed in such a manner that when the engine brake is slowing the vehicle the brake lights are activated.

The ABS system will automatically disengage the auxiliary braking device, when required.

CLUTCH FAN
A fan clutch will be provided. The fan clutch will be automatic when the pump transmission is in "Road" position, and constantly engaged when in "Pump" position.

ENGINE AIR INTAKE
The engine air intake will be located above the engine cooling package. It will draw fresh air from the front of the apparatus through the radiator grille.

The ember separator is designed to prevent road dirt and recirculating hot air from entering the engine.

The ember separator will be easily accessible by tilting the cab.

EXHAUST SYSTEM
The exhaust system will be stainless steel from the turbo to the engine's aftertreatment device. The exhaust system will include an aftertreatment device to meet current EPA standards. An insulation wrap will be provided on all exhaust pipe between the turbo and the aftertreatment device to minimize the transfer of heat to the cab.

The exhaust will terminate horizontally ahead of the right side rear wheels and will be flush with the body rub rail. The exhaust pipes will be aluminized steel.

There will be a stainless steel exhaust diffuser reduced to 5.00" in the center to accommodate the fire department's air recovery system with a standard straight tip on the end provided to reduce the temperature of the exhaust as it exits. Heat deflector shields will be provided to isolate chassis and body components from the heat of the tailpipe diffuser.

RADIATOR
The radiator and the complete cooling system will meet or exceed the current edition of applicable NFPA and engine manufacturer cooling system standards.

For maximum corrosion resistance and cooling performance, the entire radiator core will be constructed using long life aluminum alloy. The radiator core will consist of aluminum fins, having a serpentine design, brazed to aluminum tubes.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 17 of 115
The radiator core will have a minimum front area of 1060 square inches.

Supply tank will be made of heavy duty glass-reinforced nylon and the return tank will be made of aluminum. Both tanks will be crimped onto the core assembly using header tabs and a compression gasket to complete the radiator core assembly. There will be a full steel frame around the inserts to enhance cooling system durability and reliability.

The radiator will be compatible with commercial antifreeze solutions.

The radiator assembly will be isolated from the chassis frame rails with rubber isolators to prevent the development of leaks caused by twisting or straining when the apparatus operates over uneven terrain.

The radiator will include a de-aeration/expansion tank. For visual coolant level inspection, the radiator will have a built-in sight glass. The radiator will be equipped with a 15 psi pressure relief cap.

A drain port will be located at the lowest point of the cooling system and/or the bottom of the radiator to permit complete flushing of the coolant from the system.

Shields or baffles will be provided to prevent recirculation of hot air to the inlet side of the radiator.

COOLANT LINES
Gates® silicone or a combination of silicone and rubber hoses will be used for the radiator and cab heater hoses installed by the chassis manufacturer.

The chassis manufacturer will also use Gates® brand hose on other heater and auxiliary coolant circuits. There will be some areas in which an appropriate Gates product is not available. In those instances a comparable silicone hose from another manufacturer will be used.

Rubber hoses will be used for the overhead defrost/heater system only in the drain tubes of the cab.

Hose clamps will be stainless steel constant torque type to prevent coolant leakage. They will react to temperature changes in the cooling system and expand or contract accordingly while maintaining a constant clamping pressure on the hose.

FUEL TANK
A 65 gallon fuel tank will be provided and mounted at the rear of the chassis. The tank will be constructed of 12-gauge, hot rolled steel. It will be equipped with swash partitions and a vent. To eliminate the effects of corrosion, the fuel tank will be mounted with stainless steel straps.

A 0.75" drain plug will be located in a low point of the tank for drainage.

A fill inlet will be located on the left hand side of the body and is covered with a hinged, spring loaded, stainless steel door that is marked "Ultra Low Sulfur - Diesel Fuel Only." A 0.50" diameter vent will be installed from tank top to just below fuel fill inlet.

The fuel tank will meet all FHWA 393.67 requirements including a fill capacity of 95 percent of tank volume.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 18 of 115
All fuel lines will be provided as recommended by the engine manufacturer.

DIESEL EXHAUST FLUID TANK
A 4.5 gallon diesel exhaust fluid (DEF) tank will be provided and mounted in the driver's side body rearward of the rear axle.

A 0.50" drain plug will be provided in a low point of the tank for drainage.

A fill inlet will be provided and marked "Diesel Exhaust Fluid Only". The fill inlet will be located adjacent to the air bottle storage behind a common door on the driver side of the vehicle.

The tank will meet the engine manufacturers requirement for 10 percent expansion space in the event of tank freezing.

The tank will include an integrated heater unit that utilizes engine coolant to thaw the DEF in the event of freezing.

FUEL PRIMING PUMP
A Cummins automatic electronic fuel priming pump will be integrated as part of the engine.

FUEL SHUTOFF
A fuel line shutoff valve will be installed on both the inlet and outlet of the primary fuel filter.

FUEL COOLER
An air to fuel cooler will be installed in the engine fuel return line.

The fuel filler cap will have a retaining chain and holder provided on the fuel fill door.

FUEL/WATER SEPARATOR
In addition to the standard fuel filters, a Racor 690R1210, 10 micron fuel/water separator with heater will be provided.

TRANSMISSION
An Allison 6th generation, Model EVS 4000P, electronic, torque converting, automatic transmission will be provided.

The transmission will be equipped with prognostics to monitor oil life, filter life, and transmission health.

A wrench icon on the shift selector's digital display will indicate when service is due.

Two (2) PTO openings will be located on left side and top of converter housing (positions 8 o'clock and 1 o'clock).

A transmission temperature gauge with an amber light and buzzer will be installed on the cab instrument panel.

TRANSMISSION SHIFTER
A six (6)-speed push button shift module will be mounted to right of driver on console. Shift position indicator will be indirectly lit for after dark operation.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 19 of 115
The transmission ratio will be:
1st 3.51 to 1.00
2nd 1.91 to 1.00
3rd 1.43 to 1.00
4th 1.00 to 1.00
5th 0.75 to 1.00
6th 0.64 to 1.00
R 4.80 to 1.00

TRANSMISSION COOLER
A Modine plate and fin transmission oil cooler will be provided using engine coolant to control the transmission oil temperature.

TRANSMISSION PROGRAM
The transmission will not shift to neutral when parking brake is set.

TRANSMISSION FLUID
The transmission will be provided with TranSynd, or other Allison approved TES-668 heavy duty synthetic transmission fluid.

DRIVELINE
Drivelines will be a heavy-duty metal tube and be equipped with Spicer® 1810 universal joints.

The shafts will be dynamically balanced before installation.

A splined slip joint will be provided in each driveshaft where the driveline design requires it. The slip joint will be coated with Glidecoat® or equivalent.

STEERING
Dual Sheppard, Model M110, steering gears, with integral heavy-duty power steering, will be provided.

For reduced system temperatures, the power steering will incorporate an air to oil cooler and an Eaton, Model VN20, hydraulic pump with integral pressure and flow control. All power steering lines will have wire braded lines with crimped fittings.

A tilt and telescopic steering column will be provided to improve fit for a broader range of driver configurations.

STEERING WHEEL
The steering wheel will be 18.00" in diameter, have tilting and telescoping capabilities, and a 2-spoke design.

LOGO AND CUSTOMER DESIGNATION ON HORN BUTTON
The steering wheel will have an emblem containing the Pierce logo and customer name. The emblem will have three (3) rows of text for the customer's department name. There will be a maximum of eight (8) characters in the first row, 11 characters in the second row and 11 characters in the third row.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 20 of 115
The first row of text will be: ALAMEDA
The second row of text will be: COUNTY
The third row of text will be: FIRE
BUMPER
A one (1) piece, stainless steel bumper, minimum of 10.00" high, will be attached to the front of the frame.

A 9.00" channel will be mounted directly behind the bumper for additional strength.

The bumper will be extended 10.00" from front face of cab.

Gravel Pan
A gravel pan, constructed of bright aluminum treadplate, will be furnished between the bumper and cab face. The gravel pan will be properly supported from the underside to prevent flexing and vibration of the aluminum treadplate.

HOSE TRAY
A hose tray, constructed of aluminum, will be placed in the center of the bumper extension.

The tray will have a capacity of 30' of 1.50" double jacket cotton-polyester hose.

Black rubber grating will be provided at the bottom of the tray. Drain holes are also provided.

Center Hose Tray Restraint
There will be one (1) pair of hose tray restraint straps located over the center mounted tray.

The restraints will be a pair of 2.00" wide black nylon straps with Velcro® fasteners provided. The strap(s) will be used to secure the hose in the tray.

LIFT AND TOW MOUNTS
Mounted to the frame extension will be lift and tow mounts. The lift and tow mounts will be designed and positioned to adapt to certain tow truck lift systems.

The lift and tow mounts with eyes will be painted the same color as the frame.

TOW HOOKS
No tow hooks are to be provided. This truck will be equipped with a lift and tow package with integral tow eyes.

SWIVEL STOP
Installed on the front bumper extension will be a stainless steel rod to limit the travel of the front outlet swivel. The travel stop will be installed to keep it from hitting the on each side of the swivel. One (1) stainless steel rod will be threaded into the bumper deck.

GRAVEL PAN/TRAY COVERS
The gravel pan and tray covers will be constructed of 0.188" bright aluminum treadplate.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 21 of 115
CAB
The Enforcer cab will be designed specifically for the fire service and manufactured by the chassis builder.

The cab will be built by the apparatus manufacturer in a facility located on the manufacturer's premises.

For reasons of structural integrity and enhanced occupant protection, the cab will be a heavy duty design, constructed to the following minimal standards.

The cab will have 12 main vertical structural members located in the A-pillar (front cab corner posts), Bpillar (side center posts), C-pillar (rear corner posts), and rear wall areas. The A-pillar will be constructed of solid A356-T5 aluminum castings. The B-pillar and C-pillar will be constructed from

0.13" wall extrusions. The rear wall will be constructed of two (2) 2.00" x 2.00" outer aluminum extrusions and two (2) 2.00" x 1.00" inner aluminum extrusions. All main vertical structural members will run from the floor to 4.625" x 3.864" x 0.090" thick roof extrusions to provide a cage-like structure with the A-pillar and roof extrusions being welded into a 0.25" thick corner casting at each of the front corners of the roof assembly.

The front of the cab will be constructed of a 0.13" firewall plate, covered with a 0.090" front skin (for a total thickness of 0.22"), and reinforced with a full width x 0.50" thick cross-cab support located just below the windshield and fully welded to the engine tunnel. The cross-cab support will run the full width of the cab and weld to each A-pillar, the 0.13" firewall plate, and the front skin.

The cab floors will be constructed of 0.125" thick aluminum plate and reinforced at the firewall with an additional 0.25" thick cross-floor support providing a total thickness of 0.375" of structural material at the front floor area. The front floor area will also be supported with two (2) triangular 0.30" wall extrusions that also provides the mounting point for the cab lift. This tubing will run from the floor wireway of the cab to the engine tunnel side plates, creating the structure to support the forces created when lifting the cab.

The cab will be 96.00" wide (outside door skin to outside door skin) to maintain maximum maneuverability.

The centerline of front axle to the rear of the cab will be 70.00" long.

The forward cab section will have an overall height (from the cab roof to the ground) of approximately

99.00". The crew cab section will have a 10.00" raised roof, with an overall cab height of approximately 109.00". The overall height listed will be calculated based on a truck configuration with the lowest suspension weight rating, the smallest diameter tires for the suspension, no water weight, no loose equipment weight, and no personnel weight. Larger tires, wheels, and suspension will increase the overall height listed.

The floor to ceiling height inside the crew cab will be 64.50" in the center and outboard positions.

The crew cab floor will measure 46.00" from the rear wall to the back side of the rear facing seat risers.

The medium block engine tunnel, at the rearward highest point (knee level), will measure 61.50" to the rear wall. The big block engine tunnel will measure 51.50" to the rear wall.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 22 of 115
The crew cab will be a totally enclosed design with the interior area completely open to improve visibility and verbal communication between the occupants.

The cab will be a full tilt cab style.

A 3-point cab mount system with rubber isolators will improve ride quality by isolating chassis vibrations from the cab.

CAB ROOF DRIP RAIL
For enhanced protection from inclement weather, a drip rail will be furnished on the sides of the cab.

The drip rail will be painted to match the cab roof, and bonded to the sides of the cab. The drip rail will extend the full length of the cab roof.

FENDER LINERS
Full circular inner fender liners in the wheel wells will be provided.

PANORAMIC WINDSHIELD
A one (1)-piece safety glass windshield will be provided with over 2,775 square inches of clear viewing area. The windshield will be full width and will provide the occupants with a panoramic view. The windshield will consist of three (3) layers: outer light, middle safety laminate, and inner light. The outer light layer will provide superior chip resistance. The middle safety laminate layer will prevent the windshield glass pieces from detaching in the event of breakage. The inner light will provide yet another chip resistant layer. The cab windshield will be bonded to the aluminum windshield frame using a urethane adhesive. A custom frit pattern will be applied on the outside perimeter of the windshield for a finished automotive appearance.

WINDSHIELD WIPERS
Three (3) electric windshield wipers with washer will be provided that meet FMVSS and SAE requirements.

The washer reservoir will be able to be filled without raising the cab.

ENGINE TUNNEL
Engine hood side walls will be constructed of 0.375" aluminum. The top will be constructed of 0.125" aluminum and will be tapered at the top to allow for more driver and passenger elbow room.

The engine hood will be insulated for protection from heat and sound. The noise insulation keeps the dBA level within the limits stated in the current edition of applicable NFPA standards.

The engine tunnel will be no higher than 17.00" off the crew cab floor.

INTERIOR CAB INSULATION
The cab will include 1.00" insulation in the ceiling, 1.50" insulation in the side walls, a minimum of 1.00" insulation in the crew cab floor, and 2.00" insulation in the rear wall to maximize acoustic absorption and thermal insulation.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 23 of 115

CAB REAR WALL EXTERIOR COVERING
The exterior surface of the rear wall of the cab will be overlaid with bright aluminum treadplate except for areas that are not typically visible when the cab is lowered.

CAB LIFT
A hydraulic cab lift system will be provided consisting of an electric powered hydraulic pump, dual lift cylinders, and necessary hoses and valves.

Hydraulic pump will have a manual override for backup in the event of electrical failure.

Lift controls will be located DS step well center.

The cab will be capable of tilting 43 degrees to accommodate engine maintenance and removal.

The cab will be locked down by a 2-point normally closed spring loaded hook type latch that fully engages after the cab has been lowered. The system will be hydraulically actuated to release the normally closed locks when the cab lift control is in the raised position and cab lift system is under pressure. When the cab is completely lowered and system pressure has been relieved, the spring loaded latch mechanisms will return to the normally closed and locked position.

The hydraulic cylinders will be equipped with a velocity fuse that protects the cab from accidentally descending when the control is located in the tilt position.

For increased safety, a redundant mechanical stay arm will be provided that must be manually put in place on the left side between the chassis and cab frame when the cab is in the raised position. This device will be manually stowed to its original position before the cab can be lowered.

Cab Lift Interlock
The cab lift system will be interlocked to the parking brake. The cab tilt mechanism will be active only when the parking brake is set and the ignition switch is in the on position. If the parking brake is released, the cab tilt mechanism will be disabled.

CAB TILT CIRCUIT
The cab tilt mechanism will be operational with the battery switch on and with parking brake set.

CAB LIFT RESERVOIR LABEL
A label will be provided on the cab lift reservoir to indicate when the reservoir is full. The label will read "full level" with the cab in the raised position.

GRILLE
A bright finished aluminum mesh grille screen, inserted behind a bright finished grille surround, will be provided on the front center of the cab.

STEP RISER SCUFFPLATE
Aluminum treadplate scuffplates will be provided on the vertical surface between the crew cab steps and floor in the crew cab.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 24 of 115

SCUFFPLATE
A bright aluminum treadplate scuffplate will be provided on the entire rear vertical surface of the engine tunnel.

DOOR JAMB SCUFFPLATES
All cab door jambs will be furnished with a 1.00" polished stainless steel scuffplate, mounted on the striker side of the jamb.

MIRRORS
One (1) Ramco, Model 8000-PCHR, polished aluminum mirror will be mounted on each of the cab doors. The mirrors will be 9.25" wide x 13.50" high with a convex section. The mirror head will have a highly polished aluminum finish.

The flat glass in each mirror will be heated and adjustable, with remote controls that are convenient to the driver.

The convex section in each mirror will be heated and adjustable, with remote controls that are convenient to the driver.

DOORS
To enhance entry and egress to the cab, the forward cab door openings will be a minimum of 37.50" wide x 63.37" high. The crew cab doors will be located on the sides of the cab and will be constructed in the same manner as the forward cab doors. The crew cab door openings will be a minimum of

34.30" wide x 73.25" high.

The forward cab and crew cab doors will be constructed of extruded aluminum with a nominal material thickness of 0.093". The exterior door skins will be constructed from 0.090" aluminum.

A customized, vertical, pull-down type door handle will be provided on the exterior of each cab door.

The finish of the door handle will be chrome/black. The exterior handle will be designed specifically for the fire service to prevent accidental activation, and will provide 4.00" wide x 2.00" deep hand clearance for ease of use with heavy gloved hands.

Each door will also be provided with an interior flush, open style paddle handle that will be readily operable from fore and aft positions, and be designed to prevent accidental activation. The interior handles will provide 4.00" wide x 1.25" deep hand clearance for ease of use with heavy gloved hands.

The cab doors will be provided with both interior (rotary knob) and exterior (keyed) locks exceeding FMVSS standards. The keys will be Model 751. The locks will be capable of activating when the doors are open or closed. The doors will remain locked if locks are activated when the doors are opened, then closed.

A full length, heavy duty, stainless steel, piano-type hinge with a 0.38" pin and 11 gauge leaf will be provided on all cab doors. There will be double automotive-type rubber seals around the perimeter of the door framing and door edges to ensure a weather-tight fit.

A chrome grab handle will be provided on the inside of each cab door for ease of entry.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 25 of 115
A red webbed grab handle will be installed on the crew cab door stop strap. The grab handles will be securely mounted.

The bottom cab step at each cab door location will be located below the cab doors and will be exposed to the exterior of the cab.

Door Panels
The inner cab door panels will be constructed out of polished stainless steel.

ELECTRIC OPERATED CAB DOOR WINDOWS
All four (4) cab doors will be equipped with electric operated windows with one (1) flush mounted automotive style switch on each door. The driver's door will have four (4) switches, one (1) to control each door window.

Each switch will allow intermittent or auto down operation for ease of use. Auto down operation will be actuated by holding the window down switch for approximately 1 second.

CAB STEPS
The forward cab and crew cab access steps will be a full size two (2) step design to provide largest possible stepping surfaces for safe ingress and egress. The bottom steps will be designed with a grip pattern punched into bright aluminum treadplate material to provide support, slip resistance, and drainage. The bottom steps will be a bolt-in design to minimize repair costs should they need to be replaced. The forward cab steps will be a minimum 25.00" wide, and the crew cab steps will be 21.65" wide with a 10.00" minimum depth. The inside cab steps will not exceed 16.50" in height.

The vertical surfaces of the step well will be aluminum treadplate.

CAB EXTERIOR HANDRAILS
A 1.25" diameter slip-resistant, knurled aluminum handrail will be provided adjacent to each cab and crew cab door opening to assist during cab ingress and egress.

STEP LIGHTS
There will be six (6) white LED step lights with chrome housing installed for cab and crew cab access steps.
• One (1) light for the left access steps.
• Two (2) lights for the left side crew cab access steps. • Two (2) lights for the right side crew cab access steps. • One (1) light for the right side access step.

In order to ensure exceptional illumination, each light will provide a minimum of 25 foot-candles (fc) covering an entire 15" x 15" square placed ten (10) inches below the light and a minimum of 1.5 fc covering an entire 30" x 30" square at the same ten (10) inch distance below the light.

The lights will be activated when the battery switch is on and the adjacent door is opened.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 26 of 115

FENDER CROWNS
Stainless steel fender crowns will be installed at the cab wheel openings. The fender crowns will have a radius outside corner that will allow the fender crown to extend out further than the standard width crown, thus extending beyond the sidewall of the front tires and allow the crew cab doors to open fully.

HANDRAILS BELOW CAB WINDSHIELD
A 10.00" long x 1.25" diameter handrail will be mounted below the front cab windshield, one (1) on each side. The handrails will be extruded aluminum with a ribbed design to provide a positive gripping surface.

GRAB HANDLE(S)
There will be three (3) chrome grab handle(s) mounted in the interior of the cab (1) mounted vertical, high and forward on officer door, and both crew cab doors. (Reference job 36880 officer door location).

The grab handle(s) will be securely mounted.

LEFT SIDE UPPER CREW CAB DOOR WINDOW TINT
The upper window in the left side crew cab door will be tinted medium gray.

RIGHT SIDE ROLLUP CREW CAB DOOR WINDOW TINT
The rollup window in the right side crew cab door will be tinted medium gray.

RIGHT SIDE UPPER CREW CAB DOOR WINDOW TINT
The upper window in the right side crew cab door will be tinted medium gray.

LEFT SIDE ROLLUP CREW CAB DOOR WINDOW TINT
The rollup window in the left side crew cab door will be tinted medium gray.

STORAGE COMPARTMENT
Provided under the forward facing crew cab seats will be a transverse compartment. The compartment will be divided into upper and lower sections by a removable divider located at the cab floor.

The upper section will be 16.25" wide x 9.00" high x full width (transverse) of the crew cab. The lower section will be 15.00" wide x 24.50" high x 15.00" deep on both sides. The compartment will extend from the bottom of the cab to top of the seat riser.

A 4.00" long x 7.50" diameter tube will be recessed below each side of the cab compartment floor. The tube will be angled approximately 10 degrees for ease of removing an extinguisher from the compartment.

There will be two (2) double pan doors painted to match the cab exterior with a locking D-Ring latch with #1250 key, one (1) on each side of the cab with a pneumatic stay arm for each exterior door provided as a door stop. The clear door opening of each compartment door will be 10.25" wide x 32.00" high.

The exterior access will be provided with a polished stainless steel scuffplate on the lower door frame.

There will be one (1) drop down door, painted to match the cab interior with two (2) non-locking flush lift and turn latches with no louvers on the forward face of the seat riser.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 27 of 115
The compartment interior will be painted to match the cab interior.

Compartment Light
There will be four (4) white LED strip lights, one (1) each hinged side of lower and upper exterior compartment door openings. The lights will be controlled by an automatic door switch.

SCUFFPLATE
A full height polished stainless steel scuffplate will be installed on the inside of each of the auxiliary cab compartment door pans.

MATTING IN AUXILIARY COMPARTMENT
Turtle Tile vinyl matting will be provided in three (3) auxiliary compartment(s) located LS and RS aux compartments behind crew cab door. . Tile color will be LS and RS auxiliary compartment floor and tubes, and transverse floor..

The matting will be 0.75" thick and be cross bonded by 0.25" diameter ribbed sections spaced for aeration.

DOOR FRAME SCUFFPLATE
There will be two (2)polished stainless steel scuffplate(s) provided for the latch side of the door frame located LS and RS Aux Exterior Compartments.

DOOR STOP CABLES
Cables will be supplied to keep the crew cab compartment doors from hitting things when the doors are opened. There will be two (2) located in the compartments to the rear of the crew cab doors.

CAB DASH
The driver side dash, switch panel located to the right of the driver, and center console will be constructed of metal and painted gray.

The officer side dash will be a flat top design with an upper beveled edge to provide easy maintenance and will be constructed out of aluminum and painted to match the cab interior.

The instrument gauge cluster will be surrounded with a high impact ABS plastic contoured to the same shape of the instrument gauge cluster.

MOUNTING PLATE ON ENGINE TUNNEL
Equipment installation provisions will be installed on the engine tunnel.

A 0.188" smooth aluminum plate will be bolted to the top surface of the engine tunnel. The plate will follow the contour of the engine tunnel and will run the entire length of the engine tunnel. The plate will be spaced off the engine tunnel .75" to allow for wire routing below the plate.

The mounting surface will be painted to match the cab interior.

CAB INTERIOR
The cab interior will be constructed of primarily metal (painted aluminum) to withstand the severe duty cycles of the fire service.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 28 of 115
The engine tunnel will be padded and covered, on the top and sides, with dark silver gray 36 ounce leather grain vinyl resistant to oil, grease, and mildew.

For durability and ease of maintenance, the cab interior side walls will be painted aluminum. The rear wall will be painted aluminum.

The headliner will be installed in both forward and rear cab sections. Headliner material will be vinyl. A sound barrier will be part of its composition. Material will be installed on an aluminum sheet and securely fastened to interior cab ceiling.

The forward portion of the cab headliner will permit easy access for service of electrical wiring or other maintenance needs.

All wiring will be placed in metal raceways.

CAB INTERIOR UPHOLSTERY
The cab interior upholstery will be 36 oz dark silver gray vinyl.

CAB INTERIOR PAINT
The cab interior metal surfaces, excluding the rear heater panels, will be painted gray, vinyl texture paint.

The rear heater panels will be painted black, vinyl textured paint.

CAB FLOOR
The cab and crew cab flooring will be constructed with bright aluminum treadplate.

DEFROST/AIR CONDITIONING SYSTEM
A ceiling mounted combination heater, defroster and air conditioning system will be installed in the cab above the engine tunnel area.

Cab Defroster
A 54,000 BTU heater-defroster unit with 690 SCFM of air flow will be provided inside the cab. The heater-defrost will be installed in the forward portion of the cab ceiling. Air outlets will be strategically located in the cab header extrusion per the following:
• One (1) adjustable outlet directed towards the left side cab window. • One (1) adjustable outlet directed towards the right side cab window. • Six (6) fixed outlets directed at the windshield.

The defroster will be capable of clearing 98 percent of the windshield and side glass when tested under conditions where the cab has been cold soaked at 0 degrees Fahrenheit for 10 hours, and a 2 ounce per square inch layer of frost/ice has been able to build up on the exterior windshield. The defroster system will meet or exceed SAE J382 requirements.

Cab/Crew Auxiliary Heater
There will be no auxiliary heater provided in the rear facing seat risers.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 29 of 115
Air Conditioning
A condenser will be a 59,644 BTU output that meets and exceeds the performance specification will be mounted on the radiator.

The air conditioning system will be capable of cooling the average cab temperature from 100 degrees Fahrenheit to 75 degrees Fahrenheit at 50 percent relative humidity within 30 minutes. The cooling performance test will be run only after the cab has been heat soaked at 100 degrees Fahrenheit for a minimum of 4 hours.

The evaporator unit will be installed in the rear portion of the cab ceiling over the engine tunnel. The evaporator will include one (1) high performance heating core, one (1) high performance cooling core with (1) plenum directed to the front and one (1) plenum directed to the rear of the cab. The rear plenum will be covered with a metal cover painted to match the cab interior.

The evaporator unit will have a 52,000 BTU at 690 SCFM rating that meets and exceeds the performance specifications.

Adjustable air outlets will be strategically located on the forward plenum cover per the following:
• Four (4) outlets directed towards the seating position on the left side of the cab. • Four (4) outlets directed towards the seating position on the right side of the cab.

Adjustable air outlets will be strategically located on the rear plenum cover per the following:
• Minimum of five (5) outlets directed towards crew cab area.

A high efficiency particulate air (HEPA) filter will be included for the system. Access to the filter cover will be hinged with two (2) thumb latches.

The air conditioner refrigerant will be R-134A and will be installed by a certified technician.

Climate Control
An automotive style controller will be provided to control the heat and air conditioning system within the cab. The controller will have three (3) functional knobs for fan speed, temperature, and air flow distribution (front to rear) control.

The system will control the temperature of the cab and crew cab automatically by pushing the center of the fan speed control knob. Rotate the center temperature control knob to set the cab and crew cab temperature.

The AC system will be manually activated by pushing the center of the temperature control knob.

Pushing the center of the air flow distribution knob will engage the AC for max defrost, setting the fan speeds to 100 percent and directing all air flow to the overhead forward position.

The system controller will be located within panel position #12.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 30 of 115
Gravity Drain Tubes
Two (2) condensate drain tubes will be provided for the air conditioning evaporator. The drip pan will have two (2) drain tubes plumbed separately to allow for the condensate to exit the drip pan. No pumps will be provided.

SUN VISORS
Two (2) smoked Lexan™ sun visors will be provided. The sun visors will be located above the windshield with one (1) mounted on each side of the cab.

There will be no retention bracket provided to help secure each sun visor in the stowed position.

GRAB HANDLES
A black rubber covered grab handle will be mounted on the door post of the driver and officer's side cab door to assist in entering the cab.

An additional black rubber covered grab handle will be mounted on the driver's side door post of the driver's side cab door to assist in entering the cab. The grab handle will be securely mounted directly below the upper grab handle as not to interfere with the steering wheel.

An additional black rubber covered grab handle will be mounted low on the officer's side door post.

The grab handles will be securely mounted to the post area between the door and windshield.

ENGINE COMPARTMENT LIGHT
An engine compartment light will be installed under the engine tunnel, of which the switch is an integral part. Light will have a 0.125" diameter hole in its lens to prevent moisture retention.

ACCESS TO ENGINE DIPSTICKS
For access to the engine oil and transmission fluid dipsticks, there will be a door on the engine tunnel, inside the crew cab. The door will be on the rear wall of the engine tunnel, on the vertical surface.

The engine oil dipstick will allow for checking only. The transmission dipstick will allow for both checking and filling.

The door will have a rubber seal for thermal and acoustic insulation. One (1) flush lift and turn latch will be provided on the access door.

SEATING CAPACITY
The seating capacity of the vehicle (including tiller cab and belted seat positions in the rescue body) will be four (4).

DRIVER SEAT
A H.O. Bostrom, Sierra, air suspension high back seat will be provided in the cab for the driver. For increased convenience, the seat will include a manual control to adjust the horizontal position (5.50" travel). To provide flexibility for multiple driver configurations, the seat will have a reclining back, adjustable from 15 degrees back to 45 degrees forward.

The seat will include no additional zip clean covers.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 31 of 115
The seat will be furnished with a 3-point, shoulder type seat belt.

OFFICER SEAT
A H.O. Bostrom, Sierra, air suspension seat will be provided in the cab for the passenger. The seat back will be a high back style with 9 degree fixed recline angle.

The seat will include no additional zip clean covers.

The seat will be furnished with a 3-point, shoulder type seat belt.

REAR FACING LEFT SIDE CABINET
A rear facing cabinet will be provided in the crew cab at the left side outboard position. The cabinet will be mounted off the edge of the seat riser so that it is even with the crew cab door frame.

The cabinet will be 22.75" wide x 28.00" high x 24.00" deep.

The cabinet will include no adjustable shelves or traysin the cabinet interior.

The cabinet will include no louvers.

There will be 1.00" lip welded in place around the top perimeter of the cabinet. There will not be anything store on the top portions without restraints.

The cabinet will provide access only from outside the cab with one (1) reverse hinged double pan door painted to match the cab exterior with a locking D-ring latch with #1250 key. The door will be located on the side of the cab over the wheelwell. A pneumatic stay arm will be provided as a door stop. The clear door opening will be 17.00" wide x 25.50" high.

The exterior access will be provided with a polished stainless steel scuffplate on the lower door frame.

The cabinet will be constructed of smooth aluminum and painted to match the cab interior.

Cabinet Light
There will be one (1) white LED strip light installed on the right side of the exterior cabinet door opening. The lighting will be controlled by an automatic door switch.

REAR FACING RIGHT SIDE CABINET
A rear facing cabinet will be provided in the crew cab at the right side outboard position. The cabinet will be mounted off the edge of the seat riser so that it is even with the crew cab door frame.

The cabinet will be 22.75" wide x 28.00" high x 23.00" deep.

The cabinet will include no adjustable shelves or traysin the cabinet interior.

The cabinet will include no louvers.

There will be a 1.00" lip welded in place around the top perimeter of the cabinet. There will not be anything store on the top portions without restraints.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 32 of 115
The cabinet will also provide access from outside the cab with one (1) reverse hinged double pan door painted to match the cab exterior with a locking D-ring latch with #1250 key. A pneumatic stay arm will be provided as a door stop. The exterior clear door opening will be 17.00" wide x 25.50" high.

The exterior access will be provided with a polished stainless steel scuffplate on the lower door frame.

The cabinet will be constructed of smooth aluminum, and painted to match the cab interior.

Cabinet Light
There will be one (1) white LED strip light installed on the left side of the exterior cabinet door opening.

The lights will be controlled by an automatic door switch.

FORWARD FACING DRIVER SIDE OUTBOARD SEAT
There will be one (1) forward facing, HO Bostrom Sierra, foldup high back seat provided at the left side outboard in the crew cab. The seat will be mounted 2.75" inboard from the standard location.

For optimal comfort, the seat will be provided with 17.00" deep cushion. The seat back will be a highback style with 90 degree fixed recline angle.

The seat will include no additional zip clean covers.

The seat will be furnished with a 3-point, shoulder type seat belt.

FORWARD FACING CENTER CABINET
A forward facing cabinet will be provided in the crew cab at the center position.

The cabinet will be 32.00" wide x 50.00" high x 18.00" deep with one (1) Amdor rollup door with anodized finish, non-locking. The frame to frame opening of the cabinet will be 29.50" wide x 44.75" high. The minimum clear door opening will be 26.75" wide x 38.87" high.

The cabinet will include two (2) infinitely adjustable shelves with a 0.75" up-turned lippainted to match the cab interior.

The cabinet will include no louvers.

The cabinet will be constructed of smooth aluminum, and painted to match the cab interior.

Cabinet Light
There will be one (1) red Amdor LED strip light installed on the left side of the interior cabinet door opening and one (1) red Amdor LED strip light installed on the right side of the interior cabinet door opening. The lighting will be controlled by an automatic door switch.

FORWARD FACING PASSENGER SIDE OUTBOARD SEAT
There will be one (1) forward facing, HO Bostrom Sierra, foldup high back seat provided at the right side outboard in the crew cab. The seat will be mounted 2.75" inboard from the standard location.

For optimal comfort, the seat will be provided with 17.00" deep cushion. The seat back will be a highback style with 0 degree fixed recline angle.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 33 of 115
The seat will include no additional zip clean covers.

The seat will be furnished with a 3-point, shoulder type seat belt.

RIGHT SIDE REAR FACING OVERHEAD STORAGE CABINET
There will be an overhead rear facing cabinet installed at the raised roof within the crew cab, on the right side of the air conditioner.

The cabinet will be 21.00" wide x 10.00" high x 34.00" deep at the bottom. The cabinet will be notched around the wireway cover.The cabinet will be provided with no false floor.

The cabinet will include one (1) lift up cabinet door. Non-locking latch, paddle handle, and gas operated stay arms will be provided.

The entire bottom of the cabinet will hinge down for better access within the cabinet. The hinge will be at the rear of the cabinet so that when the bottom is dropped and the door is open a large area for access will be provided. The drop down door will be held open with two (2) pneumatic cylinders. The door will be held shut with a quarter turn fastener on each corner.

The cabinet will be constructed of smooth aluminum and painted to match the cab interior.

Cabinet Light
There will be one (1) white LED strip light installed horizontally above each compartment door opening.

The lighting will be controlled by an automatic door switch.

LEFT SIDE REAR FACING OVERHEAD STORAGE CABINET
There will be an overhead rear facing cabinet installed at the raised roof within the crew cab, on the left side of the air conditioner.

The cabinet will be 21.00" wide x 10.00" high x 34.00" deep at the bottom. The cabinet will be notched around the wireway cover.The cabinet will be provided with no false floor.

The cabinet will include one (1) lift up cabinet door. Non-locking latch, paddle handle, and gas operated stay arms will be provided.

The entire bottom of the cabinet will hinge down for better access within the cabinet. The hinge will be at the rear of the cabinet so that when the bottom is dropped and the door is open a large area for access will be provided. The drop down door will be held open with two (2) pneumatic cylinders. The door will be held shut with a quarter turn fastener on each corner.

The cabinet will be constructed of smooth aluminum and painted to match the cab interior.

Cabinet Light
There will be one (1) white LED strip light installed horizontally above each compartment door opening.

The lighting will be controlled by an automatic door switch.

FORWARD FACING OVERHEAD STORAGE COMPARTMENT
There will be an overhead forward facing storage compartment installed at the raised roof within the crew cab. The compartment will be approximately 88.00" wide x 10.00" high x 16.34" deep.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 34 of 115
The compartment will include three (3) lift up compartment doors. Non-locking latch and gas operated stay arms will be provided.

The compartment will be constructed of smooth aluminum and painted to match the cab interior.

Compartment Light
The storage compartment lighting will consist of one (1) red Amdor LED strip light installed horizontally above each compartment door opening.

SEAT UPHOLSTERY
All seat upholstery will be leather grain light gray vinyl resistant to oil, grease and mildew. The cab will have four (4) seating positions.

ACCESS DOOR
An access door will be provided in the front edge of each rear facing seat riser with a drop down door.

The drop down door will be provided with a flush lift and turn latch and painted to match the cab interior.

There will be no louvers.

SEAT BELTS
All cab and tiller cab (if applicable) seating positions will have red seat belts. To provide quick, easy use for occupants wearing bunker gear, the female buckle and seat belt webbing length will meet or exceed the current edition of applicable NFPA and CAN/ULC - S515 standards.

The 3-point shoulder type seat belts will include height adjustment. This adjustment will optimize the belts effectiveness and comfort for the seated firefighter. The 3-point shoulder type seat belts will be furnished with dual automatic retractors that will provide ease of operation in the normal seating position.

The 3-point shoulder type belts will also include the ReadyReach D-loop assembly to the shoulder belt system. The ReadyReach feature adds an extender arm to the D-loop location placing the D-loop in a closer, easier to reach location.

Any flip up seats will include a 3-point shoulder type belts only.

To ensure safe operation, the seats will be equipped with seat belt sensors in the seat cushion and belt receptacle that will activate an alarm indicating a seat is occupied but not buckled.

HELMET STORAGE PROVIDED BY FIRE DEPARTMENT
NFPA 1900, 2024 edition, section 11.1.8.4.1 requires a location for helmet storage be provided.

There is no helmet storage on the apparatus as manufactured. The fire department will provide a location for storage of helmets.

CAB DOME LIGHTS
There will be four (4) dual LED dome lights with grey bezels provided. Two (2) lights will be mounted above the inside shoulder of the driver and officer and two (2) lights will be installed and located, one (1) on each side of the crew cab.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 35 of 115
The color of the LED's will be red and white.

The white LED's will be controlled by the door switches and the lens switch.

The color LED's will be controlled by the lens switch.

In order to ensure exceptional illumination, each white LED dome light will provide a minimum of 10.1 foot-candles (fc) covering an entire 20.00" x 20.00" square seating position when mounted 40.00" above the seat.

ENHANCED SOFTWARE FOR CAB AND CREW CAB DOME LIGHTS
The cab and crew cab dome lights will remain on for 10 seconds for improved visibility after the doors are closed.

The dome lights will dim after 10 seconds or immediately if the vehicle's transmission is put into gear.

PORTABLE HAND LIGHTS PROVIDED BY FIRE DEPARTMENT
The hand lights are not on the apparatus as manufactured. The fire department will provide and mount these hand lights.

CAB INSTRUMENTATION
The cab instrument panel include gauges, an LCD display, telltale indicator lamps, control switches, alarms, and a diagnostic panel. The function of the instrument panel controls and switches will be identified by a label adjacent to each item. Actuation of the headlight switch will illuminate the labels in low light conditions. Telltale indicator lamps will not be illuminated unless necessary. The cab instruments and controls will be conveniently located within the forward cab section, forward of the driver. The gauge assembly and switch panels are designed to be removable for ease of service and low cost of ownership.

Gauges
The gauge panel will include the following ten (10) black faced gauges with black bezels to monitor vehicle performance:
• Voltmeter gauge (volts):
o Low volts (11.8 VDC)
 Amber caution indicator on the information center with intermittent alarm  Amber caution light on gauge assembly
o High volts (15.5 VDC)
 Amber caution indicator on the information center with intermittent alarm  Amber caution light on gauge assembly
o Very low volts (11.3 VDC)
 Red warning indicator on the information center with a steady alarm  Amber caution light on gauge assembly
o Very high volts (16.0 VDC)
 Red warning indicator on the information center with a steady alarm  Amber caution light on gauge assembly
• Engine Tachometer (RPM)
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 36 of 115
• Speedometer MPH (Major Scale), KM/H (Minor Scale)
• Fuel level gauge (Empty - Full in fractions):
o Low fuel (1/8 full)
 Amber caution indicator on the information center with intermittent alarm  Amber caution light on gauge assembly
o Very low fuel (1/32 full)
 Red caution indicator on the information center with steady alarm  Amber caution light on gauge assembly
• Engine Oil pressure Gauge (PSI):
o Low oil pressure to activate engine warning lights and alarms  Red caution indicator on the information center with steady alarm  Amber caution light on gauge assembly
• Front Air Pressure Gauges (PSI):
o Low air pressure to activate warning lights and alarm  Red warning indicator on the information center with a steady alarm  Amber caution light on gauge assembly
• Rear Air Pressure Gauges (PSI):
o Low air pressure to activate warning lights and alarm  Red warning indicator on the information center with a steady alarm  Amber caution light on gauge assembly
• Transmission Oil Temperature Gauge (Fahrenheit):
o High transmission oil temperature activates warning lights and alarm  Amber caution indicator on the information center with intermittent alarm  Amber caution light on gauge assembly
• Engine Coolant Temperature Gauge (Fahrenheit):
o High engine temperature activates an engine warning light and alarms  Amber caution indicator on the information center with intermittent alarm  Amber caution light on gauge assembly
• Diesel Exhaust Fluid Level Gauge (Empty - Full in fractions):
o Low fluid (1/8 full)
 Amber indicator light in gauge dial
All gauges will perform prove out at initial power-up to ensure proper performance.

Indicator Lamps
To promote safety, the following telltale indicator lamps will be located on the instrument panel in clear view of the driver. The indicator lamps will be "dead-front" design that is only visible when active. The colored indicator lights will have descriptive text or symbols.

The following amber telltale lamps will be present:
• Low coolant
• Trac cntl (traction control) (where applicable)
• Check engine
• Check trans (check transmission
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 37 of 115
• Aux brake overheat (Auxiliary brake overheat
• Air rest (air restriction)
• Caution (triangle symbol)
• Water in fuel
• DPF (engine diesel particulate filter regeneration)
• Trailer ABS (where applicable)
• Wait to start (where applicable)
• HET (engine high exhaust temperature) (where applicable) • ABS (antilock brake system)
• MIL (engine emissions system malfunction indicator lamp) (where applicable) • Side roll fault (where applicable)
• Front air bag fault (where applicable)
The following red telltale lamps will be present:
• Warning (stop sign symbol)
• Seat belt
• Parking brake
• Stop engine
• Rack down
The following green telltale lamps will be provided:
• Left turn
• Right turn
• Battery on
The following blue telltale lamp will be provided:
• High beam
Alarms
Audible steady tone warning alarm: A steady audible tone alarm will be provided whenever a warning message is present.

Audible pulsing tone caution alarm: A pulsing audible tone alarm (chime/chirp) will be provided whenever a caution message is present without a warning message being present.

Alarm silence: Any active audible alarm will be able to be silenced by holding the ignition switch at the top position for three (3) to five (5) seconds. For improved safety, silenced audible alarms will intermittently chirp every 30 seconds until the alarm condition no longer exists. The intermittent chirp will act as a reminder to the operator that a caution or warning condition still exists. Any new warning or caution condition will enable the steady or pulsing tones respectively.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 38 of 115
Indicator Lamp and Alarm Prove-Out
A system will be provided which automatically tests telltale indicator lights and alarms located on the cab instrument panel. Telltale indicators and alarms will perform prove-out at initial power-up to ensure proper performance.

Control Switches
For ease of use, the following controls will be provided immediately adjacent to the cab instrument panel within easy reach of the driver. All switches will have backlit labels for low light applications.

Headlight/Parking light switch: A three (3)-position maintained rocker switch will be provided. The first switch position will deactivate all parking and headlights. The second switch position will activate the parking lights. The third switch will activate the headlights.

Panel back lighting intensity control switch: A three (3)-position momentary rocker switch will be provided. Pressing the top half of the switch, "Panel Up" increases the panel back lighting intensity and pressing the bottom half of the switch, "Panel Down" decreases the panel back lighting intensity.

Pressing the half or bottom half of the switch several times will allow back lighting intensity to be gradually varied from minimum to maximum intensity level for ease of use.

Ignition switch: A three (3)-position maintained/momentary rocker switch will be provided. The first switch position will turn off and deactivate vehicle ignition. The second switch position will activate vehicle ignition and will perform prove-out on the telltale indicators and alarms for 3 to 5 seconds after the switch is turned on. A green indicator lamp is activated with vehicle ignition. The third momentary position will temporarily silence all active cab alarms. An alarm "chirp" may continue as long as alarm condition exists. Switching ignition to off position will terminate the alarm silence feature and reset function of cab alarm system.

Engine start switch: A two (2)-position momentary rocker switch will be provided. The first switch position is the default switch position. The second switch position will activate the vehicle's engine.

The switch actuator is designed to prevent accidental activation.

Hazard switch will be provided on the instrument panel or on the steering column.

Heater, defroster, and air conditioning control panel.

Turn signal arm: A self-canceling turn signal with high beam headlight controls will be provided.

Windshield wiper control will have high, low and intermittent modes.

Parking brake control: An air actuated push/pull park brake control valve will be provided.

Chassis horn control: Activation of the chassis horn control will be provided through the center of the steering wheel.

High idle engagement switch: A momentary rocker switch with integral indicator lamp will be provided.

The switch will activate and deactivate the high idle function. The "OK To Engage High Idle" indicator lamp must be active for the high idle function to engage. A green indicator lamp integral to the high idle engagement switch will indicate when the high idle function is engaged.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 39 of 115
"OK To Engage High Idle" indicator lamp: A green indicator light will be provided next to the high idle activation switch to indicate that the interlocks have been met to allow high idle engagement.

Emergency switching will be controlled by multiple individual warning light switches for various groups or areas of emergency warning lights. An Emergency Master switch provided on the instrument panel that enables or disables all individual warning light switches is included.

An additional "Emergency Master" button will be provided on the lower left hand corner of the gauge panel to allow convenient control of the "Emergency Master" system from inside the driver's door when standing on the ground.

Custom Switch Panels
The design of cab instrumentation will allow for emergency lighting and other switches to be placed within easy reach of the operator thus improving safety. There will be positions for up to four (4) switch panels in the lower instrument console and up to six (6) switch panels in the overhead visor console.

All switches have backlit labels for low light conditions.

Diagnostic Panel
A diagnostic panel will be accessible while standing on the ground and located inside the driver's side door left of the steering column. The diagnostic panel will allow diagnostic tools such as computers to connect to various vehicle systems for improved troubleshooting providing a lower cost of ownership.

Diagnostic switches will allow ABS systems to provide blink codes should a problem exist.

The diagnostic panel will include the following:
• Engine diagnostic port
• Transmission diagnostic port
• ABS diagnostic port
• Roll sensor diagnostic port
• Command Zone USB diagnostic port
• ABS diagnostic switch (blink codes flashed on ABS telltale indicator) • Diesel particulate filter regeneration switch (where applicable) • Diesel particulate filter regeneration inhibit switch (where applicable) Cab LCD Display
A digital four (4)-row by 20-character dot matrix display will be integral to the gauge panel. The display will be capable of showing simple graphical images as well as text. The display will be split into three (3) sections. Each section will have a dedicated function. The upper left section will display the outside ambient temperature.

The upper right section will display the following, along with other configuration specific information:
• Odometer
• Trip mileage
• PTO hours
• Fuel consumption
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 40 of 115
• Engine hours
The bottom section will display INFO, CAUTION, and WARNING messages. Text messages will automatically activate to describe the cause of an audible caution or warning alarm. The LCD will be capable of displaying multiple text messages should more than one caution or warning condition exist.

AIR RESTRICTION INDICATOR
A high air restriction warning indicator light LCD message with amber warning indicator and audible alarm will be provided.
"DO NOT MOVE APPARATUS" INDICATOR
There will be a Whelen®, Model VTX609B, blue LED indicator light with chrome trim located in the driving compartment installed over the over head swivel siren harness hole . This light will be illuminated automatically when the ignition is on and per the current NFPA requirements. The light will be labeled "Do Not Move Apparatus" if light is on.

An audible alarm will be provided with the open door indicator light. This alarm will be a Moose, Model MPI-47B, piezo sounder and will be used only as the door open alarm when the parking brake is released.

The piezo sounder will also be wired to the extendable lights and deluge riser when supplied on the unit and wired through the warning system.

NFPA 1900, 2024 edition, Section 10.10.1 requires a red flashing or rotating light located in the driving compartment, to be illuminated automatically whenever an item is not in the stowed position and the parking brake is not fully engaged.

Per the fire department specification, a blue flashing indicator light is required.

Per the fire department specification, the indicator light will be illuminated whenever the ignition switch is on regardless of parking brake status.

The apparatus will be non compliant to NFPA 1900 standards at time of contract execution.

DO NOT MOVE TRUCK MESSAGES
Messages will be displayed on the Command Zone™, color display located within sight of the driver whenever the Do Not Move Truck light is active. The messages will designate the item or items not in the stowed for vehicle travel position (parking brake disengaged).

The following messages will be displayed (where applicable):
• Do Not Move Truck
• DS Cab Door Open (Driver Side Cab Door Open)
• PS Cab Door Open (Passenger's Side Cab Door Open)
• DS Crew Cab Door Open (Driver Side Crew Cab Door Open) • PS Crew Cab Door Open (Passenger's Side Crew Cab Door Open) • DS Body Door Open (Driver Side Body Door Open)
• PS Body Door Open (Passenger's Side Body Door Open)
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 41 of 115
• Rear Body Door Open
• DS Ladder Rack Down (Driver Side Ladder Rack Down)
• PS Ladder Rack Down (Passenger Side Ladder Rack Down) • Deck Gun Not Stowed
• Lt Tower Not Stowed (Light Tower Not Stowed)
• Fold Tank Not Stowed (Fold-A-Tank Not Stowed)
• Aerial Not Stowed (Aerial Device Not Stowed)
• Stabilizer Not Stowed
• Steps Not Stowed
• Handrail Not Stowed
Any other device that is opened, extended, or deployed that creates a hazard or is likely to cause major damage to the apparatus if the apparatus is moved will be displayed as a caution message after the parking brake is disengaged.

SWITCH PANELS
The emergency light switch panel will have a master switch for ease of use plus individual switches for selective control. Each switch panel will contain eight (8) membrane-type switches each rated for one million (1,000,000) cycles. Panels containing less than eight (8) switch assignments will include nonfunctioning black appliqués. The built-in switch panels will be located in the lower console or overhead console of the cab.

Additional switch panel(s) will be located in the overhead position(s) above the windshield or in designated locations on the lower instrument panel layout.

The switches will be membrane-type and also act as an integral indicator light. For quick, visual indication the entire surface of the switch will be illuminated white whenever back lighting is activated and illuminated green whenever the switch is active. An active illuminated switch will flash when interlock requirements are not met or device is actively being load managed. For ease of use, a two (2)-ply, scratch resistant laser engraved Gravoply label indicating the use of each switch will be placed in the center of the switch. The label will allow light to pass through the letters for ease of use in low light conditions.

WIPER CONTROL
Wiper control will consist of a two (2)-speed windshield wiper control with intermittent feature and windshield washer controls. The control will be located on the left side of the center instrument panel.

SPARE CIRCUIT
There will be two (2) pair of wires, including a positive and a negative, installed on the apparatus.

The above wires will have the following features:
• The positive wire will be connected directly to the battery switched power. • The negative wire will be connected to ground.
• Wires will be protected to 40 amps at 12 volts DC.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 42 of 115
• Power and ground will terminate (1) one each side, inside the upper rear facing storage compartment in the crew cab .
• Termination will be with heat shrinkable butt splicing. • Wires will be sized to 125 percent of the protection.

This circuit(s) may be load managed when the parking brake is set.

SPARE CIRCUIT
There will be one (1) pair of wires, including a positive and a negative, installed on the apparatus.

The above wires will have the following features:
• The positive wire will be connected directly to the battery power • The negative wire will be connected to ground
• Wires will be protected to 15 amps at 12 volts DC
• Power and ground will terminate AS PER AD PRINT
• Termination will be a 15 amp power point plug with a rubber cover • Wires will be sized to 125 percent of the protection
There will be a 48W 2-Port USB-C 3.0 Fast Charger Adapter provided.

Battery direct loads cannot be Load Managed

SPARE CIRCUIT
There will be two (2) pair of wires, including a positive and a negative, installed on the apparatus.

The above wires will have the following features:
• The positive wire will be connected directly to the ignition switched power • The negative wire will be connected to ground
• Wires will be protected to 15 amps at 12 volts DC
• Power and ground will terminate TBD at preconstruction • Termination will be with 15 amp, power point plug with rubber cover • Wires will be sized to 125 percent of the protection
The circuit(s) may be load managed when the parking brake is set.

SPARE CIRCUIT
There will be one (1) pair of wires, including a positive and a negative, installed on the apparatus.

The above wires will have the following features:
• The positive wire will be connected directly to the battery switched power • The negative wire will be connected to ground
• Wires will be protected to 20 amps at 12 volts DC
• Power and ground will terminate LS1 lower portion to the rear back corner of the compartment with a 10' loom for customer routing.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 43 of 115
• Termination will be with 3/8" studs and plastic covers • Wires will be sized to 125 percent of the protection
The circuit(s) may be load managed when the parking brake is set.

SPARE CIRCUIT
There will be one (1) sets of spare wires installed in the apparatus routed to behind switch panel #5.

Each set will include the following:
• One (1) 20 amp 12 volt DC battery direct powered wire terminated with a red covered threaded stud.
• One (1) 20 amp 12 volt DC switch battery powered wire terminated with a red covered threaded stud.
• One (1) ground terminated with a black covered threaded stud.

Wires will be sized to 125 percent of the protection.

Battery Direct loads cannot be Load Managed
Switched circuit(s) may be load managed when the parking brake is set. 14 GAUGE 6 CONDUCTOR SPARE WIRE
There will be a 14 gauge 6 conductor wire included in a separate loom installed in the apparatus.

This wire will be routed from the power distribution panel and extended to switch assy #6. NOTE: It should be routed and not hooked up as the customer will do that..

This wire will not be connected to any power source and will not be connected to the vehicle electrical system.

SPARE CIRCUIT
There will be two (2) dual USB fast charge socket mounts installed on the apparatus.

The above wires will have the following features:
• The positive wire will be connected directly to the battery switched power. • The negative wire will be connected to ground.
• Wires will be protected to 4.8 amps at 12 volts DC.
• The USB socket mount will be One (1) in each EMS compartment. • Termination will be a dual USB charger socket.
• Wires will be sized to 125% of the protection.

This circuit(s) may be load managed when the parking brake is applied.

SPARE CIRCUIT
There will be two (2) dual USB fast charge socket mounts installed on the apparatus.

The above wires will have the following features:

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 44 of 115
• The positive wire will be connected directly to the battery power. • The negative wire will be connected to ground.
• Wires will be protected to 4.8 amps at 12 volts DC.
• The USB socket mount will be AS indicated on IP Layout. • Termination will be a dual USB charger socket.
• Wires will be sized to 125 percent of the protection.

This circuit(s) may be load managed when the parking brake is applied.

SPARE CIRCUIT
There will be one (1) sets of spare wires installed in the apparatus Wiring needs to be in the overhead between driver and captain. Customer will be purchasing and installing this GPS opticom hardware as CTF..

Each set shall include the following:
• One (1) 5 amp 12 volt DC emergency master activated wire with butt splice termination. • One (1) 5 amp 12 volt DC parking brake activated wire with butt splice termination. • One (1) 5 amp 12 volt DC right directional activated with butt splice termination. • One (1) 5 amp 12 volt DC left directional activated with butt splice termination. • One (1) ground with butt splice termination.

Wires shall be sized to 125% of the protection.

STEREO RADIO
There will be one heavy duty AM/FM / Weatherband / Bluetooth stereo radio. The radio will be installed within reach of the officer. There will be 5.25" speakers installed one (1) pair of 5.25" speakers in the cab and one (1) pair of 5.25" speakers in the crew cab. The antenna will be a roof-mounted rubber antenna located on the left side of the cab.

The following Jensen features will be included:
• 180 watts max power (45W x 4); 100 watts RMS (25W x 4) • Bluetooth® streaming audio (A2DP/AVRCP)
• Weatherband
• AM/FM tuner with 30 presets
• Audio settings (volume/bass/treble/balance/fade)
• Toggle switch between day and night display
• Daylight-readable, segmented LCD
• Two-wire power with non-volatile memory and clock support • Low battery alert

INFORMATION CENTER
An information center employing a 7.00" diagonal touch screen color LCD display will be encased in an ABS plastic housing.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 45 of 115
The information center will have the following specifications:
• Operate in temperatures from -40 to 158 degrees Fahrenheit • LCD optically bonded to hardened AR glass lens
• Five weather resistant user interface switches
• Grey with black accents
• Sunlight Readable
• Linux operating system
• Minimum of 1000nits rated display
• Display can be changed to an available foreign language • A LCD display integral to the cab gauge panel will be included as outlined in the cab instrumentation area.
• Programmed to read US Customary
General Screen Design
Where possible, background colors will be used to provide "At a Glance" vehicle information. If information provided on a screen is within acceptable limits, a green background will be used.

If a caution or warning situation arises the following will occur:
• An amber background/text color will indicate a caution condition • A red background/text color will indicate a warning condition • The information center will utilize an "Alert Center" to display text messages for audible alarm tones. The text messages will be written to identify the item(s) causing the audible alarm to sound. If more than one (1) text message occurs, the messages will cycle every second until the problem(s) have been resolved. The background color for the "Alert Center" will change to indicate the severity of the "warning" message. If a warning and a caution condition occur simultaneously, the red background color will be shown for all alert center messages. • A label for each button will exist. The label will indicate the function for each active button for each screen. Buttons that are not utilized on specific screens will have a button label with no text or symbol.

Home/Transit Screen
This screen will display the following:
• Vehicle Mitigation (if equipped)
• Water Level (if the water level system includes compatible communications to the information center)
• Foam Level (if the foam level system includes compatible communications to the information center)
• Seat Belt Monitoring Screen
• Tire Pressure Monitoring (if equipped)
• Digital Speedometer
• Active Alarms
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 46 of 115
On Scene Screen
This screen will display the following and will be auto activated with pump engaged (if equipped):
• Battery Voltage
• Fuel
• Oil Pressure
• Coolant Temperature
• RPM
• Water Level (if equipped)
• Foam Level (if equipped)
• Foam Concentration (if equipped)
• Water Flow Rate (if equipped)
• Water Used (if equipped)
• Active Alarms
Virtual Buttons
There will be four (4) virtual switch panel screens that match the overhead and lower lighting and HVAC switch panels.

Page Screen
The page screen will display the following and allow the user to progress into other screens for further functionality:
• Diagnostics
o Faults
 Listed by order of occurrence
 Allows to sort by system
o Interlock
 Throttle Interlocks
 Pump Interlocks (if equipped)
 Aerial Interlocks (if equipped)
 PTO Interlocks (if equipped)
o Load Manager
 A list of items to be load managed will be provided. The list will provide a description of the load.
 The lower the priority numbers the earlier the device will be shed should a low voltage condition occur.
 The screen will indicate if a load has been shed (disabled) or not shed.  "At a glance" color features are utilized on this screen. o Systems
 Command Zone
• Module type and ID number
• Module Version
• Input or output number
• Circuit number connected to that input or output
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 47 of 115
• Status of the input or output
• Power and Constant Current module diagnostic information  Foam (if equipped)
 Pressure Controller (if equipped)
 Generator Frequency (if equipped)
o Live Data
 General Truck Data
• Maintenance
o Engine oil and filter
o Transmission oil and filter
o Pump oil (if equipped)
o Foam (if equipped)
o Aerial (if equipped)
• Setup
o Clock Setup
o Date & Time
 12 or 24 hour format
 Set time and date
o Backlight
 Daytime
 Night time
 Sensitivity
o Unit Selection
o Home Screen
o Virtual Button Setup
o On Scene Screen Setup
o Configure Video Mode
 Set Video Contrast
 Set Video Color
 Set Video Tint
• Do Not Move
o The screen will indicate the approximate location and type of item that is open or is not stowed for travel. The actual status of the following devices will be indicated  Driver Side Cab Door
 Passenger's Side Cab Door
 Driver Side Crew Cab Door
 Passenger's Side Crew Cab Door
 Driver Side Body Doors
 Passenger's Side Body Doors
 Rear Body Door(s)
 Ladder Rack (if applicable)
 Deck Gun (if applicable)
 Light Tower (if applicable)
 Hatch Door (if applicable)
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 48 of 115
 Stabilizers (if applicable)
 Steps (if applicable)
• Notifications
o View Active Alarms
 Shows a list of all active alarms including date and time of the occurrence is shown with each alarm
 Silence Alarms - All alarms are silenced
• Timer Screen
• HVAC (if equipped)
• Tire Information (if equipped)
• Ascendant Set Up Confirmation (if equipped)
Button functions and button labels may change with each screen.

VEHICLE DATA RECORDER
There will be a vehicle data recorder (VDR) capable of reading and storing vehicle information provided.

The information stored on the VDR can be downloaded through a USB port mounted in a convenient location determined by cab model. A USB cable can be used to connect the VDR to a laptop to retrieve required information. The program to download the information from the VDR will be available to download on-line.

The vehicle data recorder will be capable of recording the following data via hardwired and/or CAN inputs:
• Vehicle Speed - MPH
• Acceleration - MPH/sec
• Deceleration - MPH/sec
• Engine Speed - RPM
• Engine Throttle Position - % of Full Throttle
• ABS Event - On/Off
• Seat Occupied Status - Yes/No by Position
• Seat Belt Buckled Status - Yes/No by Position
• Master Optical Warning Device Switch - On/Off
• Internal clock syncs the time and date when a laptop is connected Seat Belt Monitoring System
A seat belt monitoring system (SBMS) will be provided on the Command Zone™ color display and in the center overhead of the cab instrument panel. The SBMS will be capable of monitoring up to 10 seating positions indicating the status of each seat position per the following:
• Seat Occupied & Buckled = Green LED indicator illuminated • Seat Occupied & Unbuckled = Red LED indicator with audible alarm • No Occupant & Buckled = Red LED indicator with audible alarm DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 49 of 115
• No Occupant & Unbuckled = No indicator and no alarm
The seat belt monitoring screen will become active on the Command Zone color display when:
• The home screen is active:
o and there is any occupant seated but not buckled or any belt buckled with an occupant. o and there are no other Do Not Move Apparatus conditions present. As soon as all Do Not Move Apparatus conditions are cleared, the SBMS will be activated.

The SBMS will include an audible alarm that will warn that an unbuckled occupant condition exists and the parking brake is released, or the transmission is not in park.

INTERCOM SYSTEM
There will be a four (4) position David Clark, Model U3800, intercom system with single radio interface capability at the driver and officer positions and remote radio push to talk buttons located Per drawing.

One unit each to the side of shoulder of each seated position.. Two (2) crew cab outboard seats will have intercom only capability.

The following components will be provided:
• One (1) U3805 Radio Cord Junction Module
• Two (2) U3815 Radio interface modules (Driver, Officer) • Two (2) Remote Push To Talk Button Kits
• One (1) U3800 Master station (1 Crew)
• One (1) U3801 Remote headset intercom station (1 Crew) • One (1) C3820 Power cord
• All necessary station cables and connectors

RADIO / INTERCOM INTERFACE INCLUDED
All radio interfaced stations will have universal radio interfaces installed. The interface wiring will be routed within the cab to Location 5, officer overhead .

UNDER THE HELMET HEADSET
There will be four (4) under the helmet, headset(s) provided adjacent to the seated firefighter.

Each David Clark, Model H3442, headset will feature:
• M-7A noise canceling electret microphone
• Hybrid wire/flex boom assembly, 280Â rotating, for perfect microphone placement on left or right side
• Dynamic earphone elements
• Advanced Undercut Gel Ear Seals for superior comfort
• Microphone on/off switch
• 6 ft. extended coil cord
• Adjustable overhead support assembly
• Carbon steel nape-band spring, black finish, rotates for left or right side mic positioning DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 50 of 115
• Independently Certified NRR: 23dB

HEADSET HANGERS
There will be four (4) headset hanger(s) installed driver's seat, officer's seat, driver's side outboard forward facing seat and passenger's side outboard forward facing seat. The hanger(s) will meet the current edition of applicable NFPA standards for equipment mounting.

RADIO SPEAKER
There will be two (2) Motorola, Model #HSN4040, water resistant radio speaker provided and mounted Speakers to be mounted on the pump[ panel area per photos.Switches will be installed between the speakers.. Cables will terminate Speaker #1 wire to terminate behind switch panel #5 labeled "VHF" and speaker #2 wire to terminate behind switch panel #6 labeled "800". .

RADIO ANTENNA MOUNT
There will be three (3) Laird Technologies, Model MABVT8, NMO style antenna mounting base(s) for variable mounting thickness to 0.50" with weatherproof cap(s) and 17 feet of RG58A/U dual shield coax located on the cab roof two (2) 18" behind the lightbar and spaced 18.00" inboard of each A/C condensor. One (1) 18" behind the front DS stub and spaced 18.00" inboard of A/C condensor (NOTE ONE IS FOR VHF, ONE FOR 800 MHZ AND ONE FOR SPARE). The cable(s) will be routed within the cab to officer side seat box.

VEHICLE CAMERA SYSTEM
There will be a color vehicle camera system provided with the following:
• One (1) Analog High Definition (AHD) camera located on the right side of the apparatus, pointing rearward, displayed automatically with the right side turn signal. • One (1) AHD camera located on the left side of the apparatus, pointing rearward, displayed automatically with the left side turn signal.
• One (1) AHD, white camera located at the rear of the apparatus, pointing rearward, displayed automatically with the vehicle in reverse.

The camera images will be displayed on the left side vehicle information center display. Audio from the microphone on the rear camera will be emitted by an amplified speaker with volume control in the blank panel to the right of the steering column.

The following components will be included:
• One (1) 1080P Rear Camera
• Two (2) 1080P Side Cameras
• All necessary cables
Camera Switcher
There will be one (1), HMU318 HD Image Processor multiplexer, 4 channel camera video switcher with remote control provided to allow single, dual, triplex, quad, trefoil, Y split and PIP view display modes on the vehicle information center display provided. The switcher will have one (1) CVBS, Composite Video Blanking and Sync, standard Definition video output and one (1) AHD, Analog High Definition video output for High Definition cameras.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 51 of 115

RECESS REAR CAMERA
A rear camera recess will be provided in the center at the rear.

ELECTRICAL POWER CONTROL SYSTEM
The primary power distribution will be located forward of the officer's seating position and be easily accessible while standing on the ground for simplified maintenance and troubleshooting. Additional electrical distribution centers will be provided throughout the vehicle to house the vehicle's electrical power, circuit protection, and control components. The electrical distribution centers will be located strategically throughout the vehicle to minimize wire length. For ease of maintenance, all electrical distribution centers will be easily accessible. All distribution centers containing fuses, circuit breakers and/or relays will be easily accessible.

Distribution centers located throughout the vehicle will contain battery powered studs for supplying customer installed equipment thus providing a lower cost of ownership.

Circuit protection devices, which conform to SAE standards, will be utilized to protect electrical circuits.

All circuit protection devices will be rated per NFPA requirements to prevent wire and component damage when subjected to extreme current overload. General protection circuit breakers will be Type-I automatic reset (continuously resetting). When required, automotive type fuses will be utilized to protect electronic equipment. Control relays and solenoid will have a direct current rating of 125 percent of the maximum current for which the circuit is protected per NFPA.

Solid-State Control System
A solid-state electronics based control system will be utilized to achieve advanced operation and control of the vehicle components. A fully computerized vehicle network will consist of electronic modules, electronic control modules to include a see through housing, a power indicator, a status indicator and circuit indicators located near their point of use to reduce harness lengths and improve reliability. The control system will comply with SAE J1939-11 recommended practices.

The control system will operate as a master-slave system whereas the main control module instructs all other system components. The system will contain patented Mission Critical software that maintains critical vehicle operations in the unlikely event of a main controller error. The system will utilize a Real Time Operating System (RTOS) fully compliant with OSEK/VDX™ specifications providing a lower cost of ownership.

For increased reliability and simplified use the control system modules will include the following attributes:
• Green LED indicator light for module power
• Red LED indicator light for network communication stability status • Control system self test at activation and continually throughout vehicle operation • No moving parts due to transistor logic
• Software logic control for NFPA mandated safety interlocks and indicators • Integrated electrical system load management without additional components • Integrated electrical load sequencing system without additional components • Customized control software to the vehicle's configuration DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 52 of 115
• Factory and field programmable to accommodate changes to the vehicle's operating parameters To assure long life and operation in a broad range of environmental conditions, the solid-state control system modules will meet the following specifications:
• Module circuit board will meet SAE J771 specifications • Operating temperature from -40 degrees Celsius to +70 degrees Celsius • Storage temperature from -40 degrees Celsius to +70 degrees Celsius • Vibration to 50g
• IP67 rated enclosure (Totally protected against dust and also protected against the effect of temporary immersion between 15 centimeters and one (1) meter) • Operating voltage from eight (8) volts to 32 volts DC The main controller will activate status indicators and audible alarms designed to provide warning of problems before they become critical.

Circuit Protection and Control Diagram
Copies of all job-specific, computer network input and output (I/O) connections will be provided with each chassis. The sheets will indicate the function of each module connection point, circuit protection information (where applicable), wire numbers, wire colors and load management information.

On-Board Electrical System Diagnostics
The on-board information center will include the following diagnostic information:
• Text description of active warning or caution alarms
• Simplified warning indicators
• Amber caution indication with intermittent alarm
• Red warning indication with steady tone alarm
Advanced diagnostic feature will be provided in this control system. From the Command Zone display or connected wireless device, these features allow the user to monitor the real-time status of every input or output on the vehicle. It also allows users logged in as an administrator to force on inputs or outputs to assist the troubleshooting process.

TCU Module with WiFi
An in cab module will provide WiFi wireless interface and data logging capability. The WiFi interface will comply with IEEE 802.11 b/g/n capabilities while communicating at 2.4 Gigahertz. The module will communicate through a white WiFi antenna allowing a line of site communication range of up to 300 feet with a roof mounted antenna.

The module will transmit a password protected web page to a WiFi enabled device (i.e. most smart phones, tablets or laptops) allowing two levels of user interaction. The firefighter level will allow vehicle monitoring of the vehicle and firefighting systems on the apparatus. The technician level will allow diagnostic access to inputs and outputs installed on the Command Zone™, control and information system.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 53 of 115
The TCU capability will record faults from the engine, transmission, ABS and Command Zone™, control and information systems as they occur. No other data will be recorded at the time the fault occurs. The data TCU will provide up to 2 Gigabytes of data storage.

The TCU will provide a means to download the TCU information and update software in the device.

Indicator Light and Alarm Prove-Out System
A system will be provided which automatically tests basic indicator lights and alarms located on the cab instrument panel.

Voltage Monitor System
A voltage monitoring system will be provided to indicate the status of the battery system connected to the vehicle's electrical load. The system will provide visual and audible warning when the system voltage is below or above optimum levels.

The alarm will activate if the system falls below 11.8 volts DC for more than two (2) minutes.

Dedicated Radio Equipment Connection Points
There will be three (3) studs provided in the primary power distribution center located in front of the officer for two-way radio equipment. The studs will consist of the following:
• 12-volt 40-amp battery switched power
• 12-volt 60-amp ignition switched power
• 12-volt 60-amp direct battery power
There will also be a 12-volt 100-amp ground stud located in or adjacent to the power distribution center.

EMI/RFI Protection
To prevent erroneous signals from crosstalk contamination and interference, the electrical system will meet, at a minimum, SAE J551/2, thus reducing undesired electromagnetic and radio frequency emissions. An advanced electrical system will be used to ensure radiated and conducted electromagnetic interference (EMI) or radio frequency interference (RFI) emissions are suppressed at their source.

The apparatus will have the ability to operate in the electromagnetic environment typically found in fire ground operations to ensure clean operations. The electrical system will meet, without exceptions, electromagnetic susceptibility conforming to SAE J1113/25 Region 1, Class C EMR for 10KHz-1GHz to 100 Volts/Meter. The vehicle OEM, upon request, will provide EMC testing reports from testing conducted on an entire apparatus and will certify that the vehicle meets SAE J551/2 and SAE J1113/25 Region 1, Class C EMR for 10KHz-1GHz to 100 Volts/Meter requirements. Component and partial (incomplete) vehicle testing is not adequate as overall vehicle design can impact test results and thus is not acceptable by itself.

EMI/RFI susceptibility will be controlled by applying appropriate circuit designs and shielding. The electrical system will be designed for full compatibility with low-level control signals and high-powered two-way radio communication systems. Harness and cable routing will be given careful attention to minimize the potential for conducting and radiated EMI/RFI susceptibility.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 54 of 115

ELECTRICAL SYSTEM PROGNOSTICS
There will be a software based vehicle tool provided to predict remaining life of the vehicles critical fluid and events.

The system will send automatic indications to the Command Zone™ information center and/or wireless enabled devices to proactively alert of upcoming service intervals.

Prognostics will include the following:
• Engine oil and filter
• Transmission oil and filter

TELEMATICS SYSTEM
Your vehicle will include a cellular-based vehicle telematics system including a telematic control unit with external cellular Wi-Fi and GPS antenna. Pierce will provide access to a web-based user interface portal that will allow users to access vehicle data collected as part of the system, allow users to configure monitoring tools, provide a global view of the location of each vehicle that has the system, provide a summary of fleet data, etc. The web-based user interface portal or certain features thereof may be provided on a subscription basis.

The telematic control unit will be fully integrated into the electrical system of the vehicle, will monitor the vehicle through the CAN data bus, and will transmit data through a secure AT&T 4G LTE cellular connection, and be provided with a 3 year subscription.

The web-based user interface portal will provide, among other features:
• User defined interval notifications
• User defined fault alerts
• Remote access to Command Zone™ diagnostics
• Vehicle analytics and activity monitoring
• Vehicle system status
The system is activated while building your vehicle and thereafter remains active for a 60-day grace period starting when your vehicle ships from the factory. This means that the system is active at the time of factory acceptance and during the 60-day grace period. By selecting this option, it is agreed that use of the system and the web-based user interface portal will be subject to the terms set forth in the Data Systems Agreement referenced at https://www.piercemfg.com/privacy-statement. Customers will be provided with an initial login at the time of factory acceptance to verify performance of the system and the web-based user interface portal. The term of the subscription, if any, will begin when the vehicle ships from the factory. If customers do not log into the web-based user interface portal and confirm acceptance of the terms before the 60-day grace period ends, the system will be deactivated, and no new data will be collected or retained Pierce. Reactivation can be coordinated through the customer's authorized Pierce Dealer.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 55 of 115

ELECTRICAL
All 12-volt electrical equipment installed by the apparatus manufacturer will conform to modern automotive practices. All wiring will be high temperature crosslink type. Wiring will be run, in loom or conduit, where exposed and have grommets where wire passes through sheet metal. Automatic reset circuit breakers will be provided which conform to SAE Standards. Wiring will be color, function and number coded. Function and number codes will be continuously imprinted on all wiring harness conductors at 2.00" intervals. Exterior exposed wire connectors will be positive locking, and environmentally sealed to withstand elements such as temperature extremes, moisture and automotive fluids.

Electrical wiring and equipment will be installed utilizing the following guidelines:

1. All holes made in the roof will be caulked with silicon. Large fender washers, liberally caulked, will be used when fastening equipment to the underside of the cab roof.

2. Any electrical component that is installed in an exposed area will be mounted in a manner that will not allow moisture to accumulate in it. Exposed area will be defined as any location outside of the cab or body.

3. Electrical components designed to be removed for maintenance will not be fastened with nuts and bolts. Metal screws will be used in mounting these devices. Also a coil of wire will be provided behind the appliance to allow them to be pulled away from mounting area for inspection and service work.

4. Corrosion preventative compound will be applied to all terminal plugs located outside of the cab or body. All non-waterproof connections will require this compound in the plug to prevent corrosion and for easy separation (of the plug).

5. All lights that have their sockets in a weather exposed area will have corrosion preventative compound added to the socket terminal area.

6. All electrical terminals in exposed areas will have silicon applied completely over the metal portion of the terminal.

All lights and reflectors, required to comply with Federal Motor Vehicle Safety Standard #108, will be furnished. Rear identification lights will be recessed mounted for protection. Lights and wiring mounted in the rear bulkheads will be protected from damage by installing a false bulkhead inside the rear compartments.

An operational test will be conducted to ensure that any equipment that is permanently attached to the electrical system is properly connected and in working order.

The results of the tests will be recorded and provided to the purchaser at time of delivery.

BATTERY SYSTEM
There will be six (6) 12 volt Stryten/Exide®, Model 31S950X3W, batteries that include the following features will be provided:
• 950 CCA, cold cranking amps
• 190 amp reserve capacity
• High cycle
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 56 of 115
• Group 31
• Rating of 5700 CCA at 0 degrees Fahrenheit
• 1140 minutes of reserve capacity
• Threaded stainless steel studs
Each battery case will be a black polypropylene material with a vertically ribbed container for increased vibration resistance. The cover will be manifold vented with a central venting location to allow a 45 degree tilt capacity.

The inside of each battery will consist of a "maintenance free" grid construction with poly wrapped separators and a flooded epoxy bottom anchoring for maximum vibration resistance.

BATTERY SYSTEM
There will be a single starting system with an ignition switch and starter button provided and located on the cab instrument panel.

MASTER BATTERY SWITCH
There will be a master battery switch provided within the cab within easy reach of the driver to activate the battery system.

An indicator light will be provided on the instrument panel to notify the driver of the status of the battery system.

BATTERY COMPARTMENTS
Batteries will be placed on non-corrosive mats and be stored in well ventilated compartments located under the cab and bolted directly to the chassis frame. The battery boxes will have reinforced sides.

The battery compartments will be constructed of 0.188" steel plate and be designed to accommodate a maximum of three (3) group 31 batteries in each compartment. The battery hold-downs will be of a non-corrosive material. All bolts and nuts will be stainless steel.

Heavy-duty, 2/0 gauge, color coded battery cables will be provided. Battery terminal connections will be coated with anti-corrosion compound.

Battery solenoid terminal connections will be encapsulated with semi-permanent rubberized compound.

JUMPER STUDS
One (1) set of battery jumper studs with plastic color-coded covers will be included on the battery compartments.

BATTERY CHARGER
There will be a Kussmaul™, Chief Series Smart Charger 6012, product code 091-266-12-60, 60 amp battery charger with build-in touch screen display provided.

The battery charger will be wired to the AC shoreline inlet through a junction box located near the battery charger.

The battery charger will be located in the cab behind the driver seat.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 57 of 115

REMOTE CONTROL PANEL - BATTERY CHARGER
There will be a Kussmaul™, Chief Series Smart Charger remote control panel, product code 091-266- RCP included.

The battery charger indicator will be located on the driver's seat riser.

AUTO EJECT FOR SHORELINE
There will be one (1) Kussmaul™, Model 091-55-20-120, 20 amp 120 volt AC shoreline inlet(s) provided to operate the dedicated 120 volt AC circuits on the apparatus.

The shoreline inlet(s) will include red weatherproof flip up cover(s).

There will be a release solenoid wired to the vehicle's starter to eject the AC connector when the engine is starting.

The shoreline(s) will be connected to the battery charger.

There will be a mating connector body supplied with the loose equipment.

There will be a label installed near the inlet(s) that state the following:
• Line Voltage
• Current Ratting (amps)
• Phase
• Frequency
The shoreline receptacle will be located on the driver side rear bulkhead of body.

ALTERNATOR
There will be a Leece-Neville, Model BLP4003, alternator provided. It will have a rated output current of 420 amp as measured by SAE method J56. The alternator will feature an integral, self diagnostic regulator and rectifier. The alternator will be connected to the power and ground distribution system with heavy-duty cables sized to carry the full rated alternator output.

ELECTRONIC LOAD MANAGER
An electronic load management (ELM) system will be provided that monitors the vehicles 12-volt electrical system, automatically reducing the electrical load in the event of a low voltage condition, and automatically restoring the shed electrical loads when a low voltage condition expires. This ensures the integrity of the electrical system.

For improved reliability and ease of use, the load manager system will be an integral part of the vehicle's solid state control system requiring no additional components to perform load management tasks. Load management systems which require additional components will not be allowed.

The system will include the following features:

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 58 of 115
• System voltage monitoring.
• A shed load will remain inactive for a minimum of five minutes to prevent the load from cycling on and off.
• Sixteen available electronic load shedding levels.
• Priority levels can be set for individual outputs.
• High Idle to not be controlled by the load manager.
o If enabled:
 "Load Man Hi-Idle On" will display on the information center.  Hi-Idle will not activate until 30 seconds after engine start up. • Individual switch "on" indicator to flash when the particular load has been shed. • The information center indicates system voltage.

The information center, where applicable, includes a "Load Manager" screen indicating the following:
• Load managed items list, with priority levels and item condition. • Individual load managed item condition:
o ON = not shed
o SHED = shed

SEQUENCER
A sequencer will be provided that automatically activates and deactivates vehicle loads in a preset sequence thereby protecting the alternator from power surges. This sequencer operation will allow a gradual increase or decrease in alternator output, rather than loading or dumping the entire 12 volt load to prolong the life of the alternator.

For improved reliability and ease of use, the load sequencing system will be an integral part of the vehicle's solid state control system requiring no additional components to perform load sequencing tasks. Load sequencing systems which require additional components will not be allowed.

Emergency light sequencing will operate in conjunction with the emergency master light switch. When the emergency master switch is activated, the emergency lights will be activated one by one at halfsecond intervals. Sequenced emergency light switch indicators will flash while waiting for activation.

When the emergency master switch is deactivated, the sequencer will deactivate the warning light loads in the reverse order.

Sequencing of the following items will also occur, in conjunction with the ignition switch, at half-second intervals:
• Cab Heater and Air Conditioning
• Crew Cab Heater (if applicable)
• Crew Cab Air Conditioning (if applicable)
• Exhaust Fans (if applicable)
• Third Evaporator (if applicable)
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 59 of 115

HEADLIGHTS
There will be four (4) JW Speaker®, Model 8800, 4" x 6" rectangular LED lights mounted in the front quad style, chrome housing on each side of the cab grille:
• the outside light on each side will contain a part number 055***1 low beam module • the inside light on each side will contain a part number 055***1 high beam module • the headlights to include chrome bezels
The low beam lights will be activated when the headlight switch is on.

The high beam and low beam lights will be activated when the headlight switch and the high beam switch is activated.

DIRECTIONAL LIGHTS
There will be two (2) Whelen 600 series, LED combination directional/marker lights provided. The lights will be located on the outside cab corners, next to the headlights.

The color of the lenses will be the same color as the LED's.

INTERMEDIATE LIGHT
There will be two (2) Weldon, Model 9186-8580-29, amber LED turn signal marker lights furnished, one (1) each side, in the rear fender panel. The light will double as a turn signal and marker light.

CAB CLEARANCE/MARKER/ID LIGHTS
There will be two (2) Truck-Lite Model 35200Y, 1.00" high x 4.00" wide x 1.25" deep lights with amber LEDs and amber lenses provided to indicate the presence and overall length of the vehicle in the following locations:
• Two (2) lights installed as front side clearance lights will be installed, one (1) on each side above the cab doors.

The lights will be installed with aluminum guards.

All other forward facing clearance lights will be included with the visor scene light.

FRONT CAB SIDE DIRECTIONAL/MARKER LIGHTS
There will be two (2) Truck-Lite®, Model 19036Y, amber LED lights installed to the outside of the chrome wrap around bezel, one (1) on each side of the cab.

The lights will activate as marker lights with the headlight switch and directional lights with the corresponding directional circuit.

REAR CLEARANCE/MARKER/ID LIGHTING
There will be a three (3) LED light bar used as identification lights located at the rear of the apparatus per the following:
• As close as practical to the vertical centerline
• Centers spaced not less than 6.00" or more than 12.00" apart DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 60 of 115
• Red in color
• All at the same height
There will be two (2) LED lights installed at the rear of the apparatus used as clearance lights located at the rear of the apparatus per the following:
• To indicate the overall width of the vehicle
• One (1) each side of the vertical centerline
• As near the top as practical
• Red in color
• To be visible from the rear
• All at the same height
There will be two (2) LED lights installed on the side of the apparatus used as marker lights as close to the rear as practical per the following:
• To indicate the overall length of the vehicle
• One (1) each side of the vertical centerline
• As near the top as practical
• Red in color
• To be visible from the side
• All at the same height
There will be two (2) red reflectors located on the rear of the truck facing to the rear. One (1) each side, as far to the outside as practical, at a minimum of 15.00", but no more than 60.00", above the ground.

There will be two (2) red reflectors located on the side of the truck facing to the side. One (1) each side, as far to the rear as practical, at a minimum of 15.00", but no more than 60.00", above the ground.

Per FMVSS 108 and CMVSS 108 requirements.

REAR FMVSS LIGHTING
The rear stop/tail and directional lighting included in the rear tail light housing will include the following:
• Two (2) Whelen®, Model M62BTT, 4.30" high x 6.70" wide x 1.40" deep brake/tail lights with red LEDs
• Two (2) Whelen, Model M62T, 4.30" high x 6.70" wide x 1.40" deep directional lights with amber LEDs. The directional lights will be set to Steady On (Arrow) flash pattern. • The lens color(s) to be the same as the LEDs.

There will be two (2) Whelen Model M62BU, LED backup lights provided in the tail light housing.

LICENSE PLATE BRACKET
One (1) license plate bracket constructed of stainless steel will be provided at the rear of the apparatus.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 61 of 115
One (1) white LED light with chrome housing will be provided to illuminate the license plate. A stainless steel light shield will be provided over the light that will direct illumination downward, preventing white light to the rear.

LIGHTING BEZEL
There will be two (2) Whelen, Model M6FCV4P, four (4) place chromed ABS housings with Pierce logos provided for the rear M6 series stop/tail, directional, back up, scene lights or warning lights.

BACK-UP ALARM
A PRECO, Model 1040, solid-state electronic audible back-up alarm that actuates when the truck is shifted into reverse will be provided. The device will sound at 60 pulses per minute and automatically adjust its volume to maintain a minimum ten (10) dBA above surrounding environmental noise levels.

BACK-UP OBSTACLE SENSING SYSTEM
A SenseStat ultrasonic backing sensor system with 4 individual zones and an LED distance display will be provided. The sensors will be mounted under the rear tailboard.

The system will detect objects that are up to eight (8) feet from the rear of the vehicle reading each of four (4) separate sensors, and displaying the distance to the one that is closest to an object.

A 3.5"W x 2.9"L x 1.6"H, four (4) column color LED display located as per AD print will show the direction and location of the obstacle. The display will show the distance from the sensor to the obstacle in meters or in feet & fractions of a foot to the sensor that is closest to an object. There will be an audible alarm with volume control integrated into the display.

WARNING LIGHT FLASH PATTERN
The flash pattern of all the exterior warning lights will be set to meet the certified California, Title XIII flash pattern by either the light manufacturer's default flash pattern or by a conversion change to the certified flash pattern.

CAB PERIMETER SCENE LIGHTS
There will be four (4) Amdor, Model AY-LB-12HW020, 350 lumens each, 20.00" white LED strip lights provided, one (1) for each cab door.

These lights will be activated automatically when the battery switch is on and the exit doors are opened or by the same means as the body perimeter scene lights.

PUMP HOUSE PERIMETER LIGHTS
There will be two (2) Amdor, Model AY-LB-12HW020, 350 lumens each, 20.00" LED weatherproof strip lights with brackets provided under the pump panel running boards, one (1) each side.

If the combination of options in the vehicle does not permit clearance for a 20.00" light, a 12.00" version of the Amdor light will be installed.

The lights will be controlled by the same means as the body perimeter lights.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 62 of 115

BODY PERIMETER SCENE LIGHTS
There will be two (2) Amdor, Model AY-LB-12HW020, 350 lumens, 20.00" long, white LED's, 12 volt DC lights provided at the rear step area of the body, one (1) each side shining to the rear.

The perimeter scene lights will be activated when a switch within reach of the driver is activated, a switch at the driver's side pump panel is activated and a switch at the passenger's side pump panel is activated.

ENHANCED SOFTWARE FOR PERIMETER LIGHTS
All perimeter lights will be deactivated when the parking brake is released unless alternate control is selected.

The cab and crew cab perimeter lights will remain on for ten (10) seconds for improved visibility after the doors closed.

STEP LIGHTS
Four (4) white LED step lights will be provided. One (1) step light will be provided on each side, on the front compartment face and two (2) step lights at the rear to illuminate the tailboard.

In order to ensure exceptional illumination, each light will provide a minimum of 25 foot-candles (fc) covering an entire 15.00" x 15.00" square placed 10.00" below the light and a minimum of 1.5 fc covering an entire 30.00" x 30.00" square at the same 10.00" distance below the light.

These step lights will be actuated with the pump panel light switch.

All other steps on the apparatus will be illuminated per the current edition of applicable NFPA standards.

SCENE LIGHTS
There will be one (1) pair of TecNiq, Model E960, LED scene light(s) with stainless steel housing, installed on the side of the apparatus, over or behind the rear axle wheel well, as space allows, one (1) each side.

A control for the light(s) selected above will be the following:
• a switch at the driver's side switch panel
• no additional switch location
• no additional switch location
• no additional switch location
These lights may be load managed when the parking brake is set.

LED HOODED WORK LIGHT
Additional Model P25 white LED work lights with chrome housing will be provided.

In order to ensure exceptional illumination, each light will provide a minimum of 25 foot-candles (fc) covering an entire 15" x 15" square placed ten (10) inches below the light and a minimum of 1.5 fc covering an entire 30" x 30" square at the same ten (10) inch distance below the light.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 63 of 115
The lights will be activated by the pump operator's panel light switch. The hooded work lights will be installed above the passenger's side pump panel. The quantity of additional hooded work lights is two (2).
12 VOLT LIGHTING
There will be a HiViz®, Model FT-B-72-ML-*, 2.56" high x 72.69" long x 2.45" deep 28,512 raw lumens 12 volt DC light provided on the front cab roof as far forward as practical.

The light will include the following:
• 54 white scene LEDs configured in spot and flood optics • three (3) amber LED identification lights
• two (2) amber LED clearance lights
The painted parts of the light housing and brackets to be white.

The light will be activated by a switch at the driver's side switch panel.

The scene LEDs may be load managed when the parking brake is applied. 12 VOLT DC SCENE LIGHTS
There will be one (1) Whelen® Model P*H2*, 17,750 lumens 12 volt DC powered lights with white LEDs and a combination of flood and spot optics installed on the apparatus located, PS back of cab. Light head shall be just above cab roof and oriented so the light head faces outboard..

The light(s) to be installed on push up side mount outside pole length to be 20.00" long with a handle holder and sensor connecting the pole to the Do Not Move Truck Indicator circuit.

The painted parts of this light assembly to be white.

The lights will be activated by a switch at the driver's side switch panel and by a switch at the left side pump panel.

The light(s) may be load managed when the parking brake is applied. 12 VOLT DC SCENE LIGHTS
There will be one (1) Whelen® Model P*H2*, 17,750 lumens 12 volt DC powered lights with white LEDs and a combination of flood and spot optics installed on the apparatus located, DS back of cab. Light head shall be just above cab roof and oriented so the light head faces outboard..

The light(s) to be installed on pull up side mount outside pole length to be 20.00" long with handle holder and sensor connecting the pole to the Do Not Move Truck Indicator circuit.

The painted parts of this light assembly to be white.

The lights will be activated by a switch at the driver's side switch panel and by a switch at the left side pump panel.

The light(s) may be load managed when the parking brake is applied.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 64 of 115

DECK LIGHTS
There will be two (2) Whelen®, Model MPBW, white 12 volt DC LED floodlights with stud bail mount provided at the rear of the hose bed, one (1) each side.

The lights will be activated by a control from the driver side switch panel.

HOSE BED LIGHT
There will be one (1) Whelen, Model 60COELZR, LED light(s) with a Whelen, Model 6EFLANGE, chrome flange installed at the forward hose bed bulkhead located Front of hose bed. The light(s) will be mounted with an aluminum tread plate bracket and with no guard.

The light(s) will be activated when the parking brake is applied.

HOSE BED LIGHT
There will be one (1) Amdor Model AY-LB-12HW040, 700 lumens, 40.00" LED light located under the cover, closer to the hinge.

The light(s) will be activated when the battery switch is on, and when the hosebed cover is raised.

WALKING SURFACE LIGHT
There will be Model FRP, 4" round black 12 volt DC LED floodlight(s) with bolt mount provided to illuminate the entire designated walking surface on top of the body.

The light(s) will be activated when the body step lights are on.

SWITCH, COMPARTMENT
A door switch will be added to on both doors for the backboard compt. above the pump module compartment door(s). The switch will be connected to the "Door Open Circuit" and the "Do Not Move Apparatus" light in the cab. A quantity of two (2) switches will be provided.

SWITCH, SPARE
There will be an electric horn selector switch installed on the switch panel. When this switch is activated the electric horns will be activated through the steering wheel horn ring.

SPECIAL REAR WARNING LIGHT SWITCHING
The upper rear warning lights and the lower rear warning lights shall be controlled by a single switch on the instrument panel.

WATER TANK
Booster tank will have a capacity of 500 gallons and be constructed of polypropylene plastic by United Plastic Fabricating, Incorporated.

Tank joints and seams will be nitrogen welded inside and out.

Tank will be baffled in accordance with the current edition of applicable NFPA standards.

Baffles will have vent openings at both the top and bottom to permit movement of air and water between compartments.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 65 of 115
Longitudinal partitions will be constructed of .38" polypropylene plastic and will extend from the bottom of the tank through the top cover to allow for positive welding.

Transverse partitions will extend from 4.00" off the bottom of the tank to the underside of the top cover.

All partitions will interlock and will be welded to the tank bottom and sides.

Tank top will be constructed of .50" polypropylene. It will be recessed .38" and will be welded to the tank sides and the longitudinal partitions.

Tank top will be sufficiently supported to keep it rigid during fast filling conditions.

Construction will include 2.00" polypropylene dowels spaced no more than 30.00" apart and welded to the transverse partitions. Two (2) of the dowels will be drilled and tapped (.50" diameter, 13.00" deep) to accommodate lifting eyes.

A sump that will be sized dependent on the tank to pump plumbing will be provided at the bottom of the water tank.

Sump will include a drain plug and the tank outlet.

Tank will be installed in a fabricated cradle assembly constructed of structural steel.

Sufficient crossmembers will be provided to properly support bottom of tank. Crossmembers will be constructed of steel bar channel or rectangular tubing.

Tank will "float" in cradle to avoid torsional stress caused by chassis frame flexing. Rubber cushions, .50" thick x 3.00" wide, will be placed on all horizontal surfaces that the tank rests on.

Stops or other provision will be provided to prevent an empty tank from bouncing excessively while moving vehicle.

Mounting system will be approved by the tank manufacturer.

Fill tower will be constructed of .50" polypropylene and will be a minimum of 8.00" wide x 14.00" long.

Fill tower will be furnished with a .25" thick polypropylene screen and a hinged cover.

An overflow pipe, constructed of 4.00" schedule 40 polypropylene, will be installed approximately halfway down the fill tower and extend through the water tank and exit to the rear of the rear axle.

SLEEVE, PLUMBING, THROUGH TANK
Two (2) sleeves will be provided in the water tank for a 3.00" pipe to the rear.

BODY MODIFICATIONS
The cross divider to the rear of the water and foam tank fill domes will be mounted with 5/16" hex head bolts. Customer has replaced the bolts for this divider on all of there previous units.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 66 of 115

HOSE BED
The hose bed will be fabricated of 12-gauge galvanneal steel.

The sides will not form any portion of the fender compartments.

Upper and rear edges of side panels will have a double break for rigidity.

The upper inside area of the beavertails will be covered with brushed stainless steel to prevent damage to painted surface when hose is removed.

Flooring of the hose bed will be removable aluminum grating with the top surface corrugated to aid in hose aeration. The grating slats will be a minimum of 0.50" x 4.50" with spacing between slats for hose ventilation.

The hose bed interior walls will be painted to match the lower body color.

Hose bed will accommodate shelf area, 800' x 5.00"DJ SYN Angus, 500' x 2.50"DJ, 500' x 2.50",DJ 200' x 1.75" Hi combat. The dimensions that customer is asking dividers to be set to are: from DS wall to centerline of divider (16.00"), 25.00", 11.00", 11.00", 5.00".

HOSE BED DIVIDER
Four (4) hosebed dividers will be furnished for separating hose.

Each divider will be constructed of a 0.25" brushed aluminum sheet. Flat surfaces will be sanded for uniform appearance or constructed of brushed aluminum.

Divider will be fully adjustable by sliding in tracks, located at the front and rear of the hose bed.

Divider will be held in place by tightening bolts, at each end.

Acorn nuts will be installed on all bolts in the hose bed which have exposed threads.

HOSE BED DEFLECTOR
A hose bed wind deflector will be provided at the front of the hose bed.

The cover will be 36.00" long x full width of the hose bed.

The cover will be constructed of .19" bright aluminum treadplate, hinged to the hose bed cross divider with a full length stainless steel piano hinge and resting on the hose bed dividers and side sheets. The cover will have a 1.00" upward "Lazy Bend" at the rear with additional bracing underneath for stiffening.

A chrome grab handle will be provided in the rear center of the cover to assist in opening and closing.

Pneumatic cylinders will be provided to hold the deflector in the open position.

The cover will be labeled "NO STEP" using 3.00" lettering.

Swell latches will be provided at the outboard rearward corners.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 67 of 115
A single pair of black nylon Velcro® straps will be provided towards the rear at the top of the hose bed to retain hose within the hose bed.

A heavy duty 2" black nylon webbing will be installed at the rear of the hose bed with seat belt buckles at the top, mounted 24.00" forward of the rear of the hose bed. The seat belt buckles will be provided with no tether release. At the bottom of the webbing, fixed style seat belt buckle will be provided. If a strap is provided, the color of the strap will be black.

A cross-divider will be provided just behind the fill tower. The divider will be bolted to the side sheet.

SCUFFPLATE/ DEFLECTOR
A 16 ga stainless steel formed deflector will be installed over each flat bar reinforcement located on the inboard wall of the hosebed. The deflector will run the length of the bar covering the entire bar flanging off each edge to prevent hard edges where hose or couplings can get caught especially at the rear of the hosebed. The cover will be flanged to attach to the hosebed wall on each side of the flat bar with flathead screws. The center of the cover will be fastened to the flat bar using the same screw as is used to attach the flat bar to the hosebed wall.

SHELF, HINGED IN HOSE BED
There will be one (1) hinged shelves, constructed of aluminum grating, provided for hose or equipment storage inside the hose bed located on the left side The dimensions of the shelf shall be 14.25" wide with a 11.50" clear opening to the grating. . The shelf will be attached to the hose bed side sheet.

RUNNING BOARDS
Running boards will be fabricated of 0.125" bright aluminum treadplate.

Each running board will be supported by a welded 2.00" square tubing and channel assembly, which will be bolted to the pump compartment substructure.

Running boards will be 12.75" deep and spaced 0.50" away from the pump panel.

A splash guard will be provided above the running board treadplate.

TAILBOARD
The tailboard will also be constructed of .125" bright aluminum treadplate and spaced .50" from the body, as well as supported by a structural steel assembly.

The tailboard area will be 26.00" deep in the center area and 10.00" deep to the rear of the side compartments. The tailboard will be T-shaped.

The exterior side will be flanged down and in for increased rigidity of tailboard structure.

REAR WALL, SMOOTH ALUMINUM/BODY MATERIAL
The rear facing surfaces of the center rear wall will be smooth aluminum.

The bulkheads, the surface to the rear of the side body compartments, will be smooth and the same material as the body.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 68 of 115
Any inboard facing surfaces below the height of the hosebed will be aluminum diamondplate.

REAR TOW EYES
Two (2) tow eyes, which are an integral part of the body mounting substructure, will be installed below the rear of the truck.

The tow eyes will be of adequate strength to allow the truck to be pulled from the eyes.

REAR TOW BAR
One (1) tow bar will be installed under the tailboard, 4.00"-6.00" forward from the rear of the tailboard.

With air ride suspension and a 65 gallon fuel tank, the tow bar will be located .50" further rearward than normal when there is this combination of options.

The tow bar assembly will be designed and positioned to allow up to a 20,000 lb straight horizontal pull in line with the centerline of the vehicle.

The tow bar design will have been tested and evaluated using finite element analysis techniques.

RUNNING BOARD HOSE RESTRAINT
A pair of 2.00" wide black nylon straps with Velcro fasteners will be provided for each hose tray to secure the hose during travel. Two (2) hose trays will be located one (1) in each side running board.

HOSE TRAY
Two (2) hose trays shall be recessed one (1) in each side running board.

33.00"L x 9.00"W x 9.00"D. Tray is to start at the very rear of the pump module and extend forward and stop short of the crosslays so the customer has ample stepping surface below the crosslays. The opening on the top of the running board is to be 9w x 30L, tray shall be notched around the rear runningboard support.

Rubber matting shall be installed on the floor of the tray to provide proper ventilation. Drain holes will be provided.

COMPARTMENTATION
Body and compartments will be fabricated of galvanneal steel.

Side compartments will be an integral assembly with the rear fenders.

Circular fender liners will be provided for prevention of rust pockets and ease of maintenance.

Side compartment flooring will be 12-gauge and of the sweep out design, with the floor higher than the compartment door lip.

The side compartment door opening will be framed by flanging the edges in 1.75" and bending out again 0.75" to form an angle.

Drip protection will be provided above the doors by means of bright aluminum extrusion, formed bright aluminum treadplate, or polished stainless steel.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 69 of 115
The top of the compartment will be covered with bright aluminum treadplate rolled over the edges on the front, rear, and outward side. These covers will have the corners TIG welded.

Side compartment covers will be separate from the compartment tops.

Front facing compartment walls will be covered with bright aluminum treadplate.

All screws and bolts which protrude into a compartment will have acorn nuts on the ends to prevent injury.

UNDERBODY SUPPORT SYSTEM
Due to the severe loading requirements of this pumper, a method of body and compartment support suitable for the intended load will be provided.

The backbone of the support system will be the chassis frame rails, which is the strongest component of the chassis and designed for sustaining maximum loads.

The support system will include 0.375" thick steel vertical angle supports bolted to the chassis frame rails with 0.625" diameter bolts.

Attached to the bottom of the steel vertical angles will be horizontal angles, with gussets welded to the vertical members, which extend to the outside edge of the body.

A steel frame will be mounted on the top of these supports to create a floating substructure, which results in a 500 lb equipment support rating per lower compartment.

The steel frames as well as the steel vertical angles will be treated with an epoxy E-coat to provide resistance to corrosion and chemicals as standard.

The floating substructure will be separated from the horizontal members with neoprene elastomer isolators. These isolators will reduce the natural flex stress of the chassis from being transmitted to the body.

The isolators will have a broad load range, proven viability in vehicular applications, be of a fail safe design and allow for all necessary movement in three (3) transitional and rotational modes.

The neoprene isolators will be installed in a modified V three (3)-point mounting pattern to reduce the natural flex of the chassis being transmitted to the body.

A design with body compartments hanging on the chassis, unsupported, will not be acceptable.

AGGRESSIVE WALKING SURFACE
All exterior surfaces designated as stepping, standing, and walking areas will comply with the required average slip resistance of the current NFPA standards.

LOUVERS
Louvers will be stamped into compartment walls to provide the proper airflow inside the body compartments and to prevent water from dripping into the compartment. Where these louvers are provided, they will be formed into the metal and not added to the compartment as a separate plate.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 70 of 115

TESTING OF BODY DESIGN
Body structural analysis will be fully tested. Proven engineering and test techniques such as finite element analysis, strain gauging, and model analysis will be performed with special attention given to fatigue, life and structural integrity of the cab, body and substructure.

The body will be tested while loaded to its greatest in-service weight.

The criteria used during the testing procedure will include:
• Raising opposite corners of the vehicle tires 9.00", simulating the twisting a truck may experience when driving over a curb.
• Making a 90 degree turn while at 20 mph, simulating aggressive driving conditions. • Driving the vehicle at 35 mph on a washboard road.
• Driving the vehicle at 55 mph on a smooth road.
• Accelerating the vehicle fully, until reaching the approximate speed of 45 mph, on rough pavement.

Evidence of actual testing techniques will be made available upon request.

LEFT SIDE COMPARTMENTATION
The left side compartmentation will consist of three rollup door compartments.

A full height, rollup door compartment ahead of the rear wheels will be provided. The interior dimensions of this compartment will be 27.50" wide x 66.63" high x 25.88" deep in the lower 25.00" of the compartment and 12.00" deep in the remaining upper portion. The clear door opening will be a minimum of 21.75" wide x 56.88" high.

A rollup door compartment over the rear wheels will be provided. The interior dimensions of this compartment will be 66.50" wide x 32.88" high x 12.00" deep. The clear door opening will be a minimum of 58.25" wide x 23.13" high.

A full height, rollup door compartment behind the rear wheels will be provided. The interior dimensions of this compartment will be 47.75" wide x 67.63" high x 25.88" deep in the lower 26.00" of height and

12.00" deep in the remaining upper section of the compartment. The clear door opening will be a minimum of 44.75" wide x 57.88" high.

The interior height of the compartments will be measured from the compartment floor to the ceiling.

The spool of the rollup door at the top of the compartment takes up some usable space. The depth of the compartments will be measured from the back wall to the inside of the door frame.

Closing of the doors will not require releasing, unlocking, or unlatching any mechanism and will easily be accomplished with one hand.

RIGHT SIDE COMPARTMENTATION
The right side compartmentation will consist of two rollup door compartments.

A rollup door compartment ahead of the rear wheels will be provided. The interior dimensions of this compartment will be 27.50" wide x 32.63" high x 25.88" deep in the lower 25.00" of the compartment DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 71 of 115
and 12.00" deep in the remaining upper portion. The clear door opening will be a minimum of 21.75" wide x 22.88" high.

A rollup door compartment behind the rear wheels will be provided. The interior dimensions of this compartment will be 47.75" wide x 33.63" high x 25.88" deep in the lower 26.00" of height and 12.00" deep in the remaining upper section of the compartment. The clear door opening will be a minimum of

44.75" wide x 23.88" high.

The interior height of the compartments will be measured from the compartment floor to the ceiling.

The spool of the rollup door at the top of the compartment takes up some usable space. The depth of the compartments will be measured from the back wall to the inside of the door frame.

Closing of the doors will not require releasing, unlocking, or unlatching any mechanism and will easily be accomplished with one hand.

SIDE COMPARTMENT ROLLUP DOOR(S)
There will be five (5) compartment doors installed on the side compartments. The doors will be double faced aluminum construction, painted one (1) color to match the lower portion of the body and manufactured by Gortite®.

Lath sections will be an interlocking rib design and will be individually replaceable without complete disassembly of door.

Between each slat at the pivoting joint will be a PVC inner seal to prevent metal to metal contact and prevent dirt or moisture from entering the compartments. Seals will allow door to operate in extreme temperatures ranging from 180 to -40 degrees Fahrenheit. Side, top and bottom seals will be provided to resist ingress of dirt and weather and be made of Santoprene.

All hinges, barrel clips and end pieces will be nylon 66. All nylon components will withstand temperatures from 300 to -40 degrees Fahrenheit.

A polished stainless steel lift bar with locking key latches to be provided for each roll-up door. The keys to be Model 1250 for all compartment doors. Lift bar will be located at the bottom of door and have latches on the outer extrusion of the doors frame. A ledge will be supplied over lift bar for additional area to aid in closing the door.

Doors will be constructed from an aluminum box section. The exterior surface of each slat will be flat.

The interior surfaces will be concave to provide strength and prevent loose equipment from jamming the door from inside.

To conserve space in the compartments, the spring roller assembly will not exceed 3.00" in diameter.

The header for the rollup door assembly will not exceed 4.00".

A heavy-duty magnetic switch will be used for control of open compartment door warning lights.

REAR COMPARTMENTATION
A roll-up door compartment above the rear tailboard will be provided.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 72 of 115
The interior dimensions of this compartment will be 40.00" wide x 33.63" high x 25.88" deep. The spool of the rollup door at the top of the compartment takes up some usable space. The depth of the compartment will be calculated with the compartment door closed.

A louvered, removable access panel will be furnished on the back wall of the compartment.

The rear compartment will be open into the rear side compartments.

The clear door opening of this compartment will be a minimum of 33.25" wide x 23.88" high.

Closing of the door will not require releasing, unlocking, or unlatching any mechanism and will easily be accomplished with one hand.

ROLLUP REAR COMPARTMENT DOOR
There will be a rear rollup door. The door will be double faced aluminum construction, painted one (1) color to match the lower portion of the body and manufactured by Gortite®.

Lath sections will be an interlocking rib design and will be individually replaceable without complete disassembly of door.

Between each slat at the pivoting joint will be a PVC inner seal to prevent metal to metal contact and prevent dirt or moisture from entering the compartments. Seals will allow door to operate in extreme temperatures ranging from 180 to -40 degrees Fahrenheit. Side, top and bottom seals will be provided to resist ingress of dirt and weather and be made of Santoprene.

All hinges, barrel clips and end pieces will be nylon 66. All nylon components will withstand temperatures from 300 to -40 degrees Fahrenheit.

A polished stainless steel lift bar with locking key latches to be provided for each roll-up door. The keys to be Model 1250 for all compartment doors. Lift bar will be located at the bottom of door and have latches on the outer extrusion of the doors frame. A ledge will be supplied over lift bar for additional area to aid in closing the door.

Door will be constructed from an aluminum box section. The exterior surface of each slat will be flat.

The interior surface will be concave to provide strength and prevent loose equipment from jamming the door from inside.

To conserve space in the compartments, the spring roller assembly will not exceed 3.00" in diameter.

The header for the rollup door assembly will not exceed 4.00".

A heavy-duty magnetic switch will be used for control of open compartment door warning lights.

SCUFFPLATE
A stainless steel scuffplate will run from the top of the catwalk 18.00" tall to protect the side sheet from a "D" handle pike pole and pike pole hook.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 73 of 115

DOOR GUARD DRAIN TUBE
There will be one (1) door guard(s) with 0.75" drain tube(s) provided and located LS3, provide a 90 degree elbow so the drain hoes does not extend into the compartment. See photos in stage 7 efolder.

DOOR GUARD
There will be five (5) compartment doors that will include a guard/drip pan designed to protect the rollup door from damage when in the retracted position and contain any water spray. The guard will be fabricated from stainless steel and installed LS1, LS2, RS1, RS2 and B1.

ROLLUP DOOR PULL STRAPS
one (1) compartment door will be provided with pull straps. The pull straps will be 14.00" long and black in color.

The straps will be installed directly to the inside of the rollup door.

The rollup door compartments to have these straps will be LS2.

ROLL-UP DOOR TRIM
The exterior of the aluminum trim around the door opening will be painted job color.

There will be six (6) compartments with the trim painted.

COMPARTMENT LIGHTING
There will be six (6) compartments with Amdor, Model AY-9250, red LED compartment light strips. The strips will be centered vertically along each side of the door framing. The compartments with these strip lights will be located all body compartments. The lights will be mounted with mechanical fasteners.

Any remaining compartments will include 6.00" diameter Truck-Lite, Model: 79384, lights in each enclosed compartment. Each light will have a number 1076 single filament, dual wire bulb.

Opening the compartment door will automatically turn the compartment lighting on.

NFPA 1901 2016 Edition 13.10.5.3 Each enclosed tool and equipment compartment greater than 4 ft cubed (01 m cubed) in volume and having an opening greater than 144 sq in shall have sufficient compartment lighting to provide a minimum of 2 fc (20 lx) at any location on the floor of the compartment without any shelves, dividers, or equipment in the compartment.

The lights tested in this configuration didn't meet this requirement. Per the fire departments specification request the apparatus shall not be compliant to NFPA 1901 standards at time of contract execution.

MOUNTING TRACKS
There will be five (5) sets of tracks for mounting shelf(s) in LS1, LS3, RS1, RS2 and B1. These tracks will be installed vertically to support the adjustable shelf(s). The tracks will be painted to match the compartment interior.

ADJUSTABLE SHELVES
There will be five (5) shelves with a capacity of 500 lb provided.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 74 of 115
The shelf construction will consist of .188" aluminum painted spatter gray with 2.00" sides.

Each shelf will be infinitely adjustable by means of a threaded fastener, which slides in a track.

The shelves will be held in place by .12" thick stamped plated brackets and bolts.

The location(s) will be in RS1 centered between the floor and the ceiling, in RS2 centered between the floor and the ceiling, in B1 centered between the floor and ceiling, in LS3 in the lower third and in LS1 in the lower third to the left of the partition.

SLIDE-OUT FLOOR MOUNTED TRAY
There will be one (1) floor mounted slide-out tray(s) provided in the lower 26" portion of LS1 forward of the vertical partition . A capacity rating will not be available on this tray due to a reduced side height being less than 2.00". The tray(s) will be constructed of a minimum .13" aluminum with welded corners.

The finish will be painted to match compartment interior.

The side height of the tray(s) will be as follows:
• Front: no lip
• Rear: 2.00" high
• Left and Right Sides: 2.00" high
There will be two undermount-roller bearing type slides rated at 250lb each provided. The pair of slides will have a safety factor rating of 2.

To ensure years of dependable service, the slides will be coated with a finish that is tested to withstand a minimum of 1,000 hours of salt spray per ASTM B117.

To ensure years of easy operation, the slides will require no more than a 50lb force for push-in or pullout movement when fully loaded after having been subjected to a 40 hour vibration (shaker) test under full load. The vibration drive file will have been generated from accelerometer data collected from a heavy truck chassis driven over rough gravel roads in an unloaded condition. Proof of compliance will be provided upon request.

Automatic locks will be provided for both the "in" and "out" positions. The trip mechanism for the locks will be located at the front of the tray for ease of use with a gloved hand.

SWING OUT TOOLBOARD
A swing out aluminum toolboard will be provided.

It will be a minimum of 0.188" thick with .203" diameter holes in a pegboard pattern with 1.00" centers between holes.

A 1.00" x 1.00" aluminum tube frame will be welded to the edge of the pegboard.

The board will be mounted on a pivoting device at the back of the compartment on the top and bottom to allow easy movement in and out of the compartment. The maximum tool load will be 400 lb.

The board will have positive lock in the stowed and extended position.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 75 of 115
The board will have a D-ring handle to secure it in the stowed position.

The board will be mounted stationary within the compartment.

One (1) toolboard(s) will be provided. The toolboard(s) will be spatter gray painted and installed LS2 full height and width.

PARTITION, TRANSVERSE REAR COMPARTMENT
Two (2) partitions will be bolted in place to separate the left and right side rear compartments from the rear tailboard compartment. The partition will be body material painted spatter gray.

VERTICAL COMPARTMENT PARTITION
One (1) partition will be provided.

The partition construction will consist of body material painted spatter gray. Each partition will be the full vertical height of the compartment.

The location(s) will be in LS1, 32.00" from the forward door frame.

MATTING, COMPARTMENT FLOOR
Turtle Tile compartment matting will be provided in four (4) compartments on the compartment floor.

The locations are, LS3, B1, RS1 and RS2.

The Turtle Tile will be black and the leading edge of the matting will include the beveled edge. The beveled edge will be black.

MATTING, COMPARTMENT SHELVING
Turtle Tile compartment matting will be provided in six (6) shelves. The locations are, all shelves / trays .

The color of the Turtle Tile will be black.

PLYWOOD LINING
Plywood will be installed on the back wall of one (1) compartments. The locations are LS2.

The plywood will be high quality .75" marine grade without any patches. Stainless steel retainers will be used to mount the plywood. The plywood will be sanded to a smooth finish and painted to match the compartment interior.

STRAP
There shall be one (1) black 1.00" wide nylon strap(s) provided on the rearward end of the hard suction trough. The strap(s) shall be fastened with Velcro in the center.

STRAP
There will be one (1) black 2.00" wide nylon strap(s) provided on the hinged hose bed shelf on the DS from the bottom of the shelf to the top of the hose bed grating. The strap(s) will be fastened with Velcro in the center.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 76 of 115

RUB RAIL
Bottom edge of the side compartments will be trimmed with a bright aluminum extruded rub rail.

Trim will be 2.12" high with 1.38" flanges turned outward for rigidity.

The rub rails will not be an integral part of the body construction, which allows replacement in the event of damage.

BODY FENDER CROWNS
Polished stainless steel fender crowns will be provided around the rear wheel openings with a dielectric barrier will be provided between the fender crown and the fender sheet metal to prevent corrosion.

The fender crowns will be held in place with stainless steel screws that thread directly into a composite nut and not directly into the parent body sheet metal to eliminate dissimilar metals contact and greatly reduce the chance for corrosion. Rubber welting will be provided between the body and crown.

BODY FENDER LINER
A painted to match the lower body color fender liner will be provided. The liners will be removable to aid in the maintenance of rear suspension components.

HARD SUCTION HOSE
One (1) length of 5.00" Kochek Fire Grade clear corrugated hard suction hose, reinforced with a black spiral helix, 10' in length, will be provided. The hose will be equipped with a 4.50" long handle female coupling on one (1) end and a 4.50" rocker lug male coupling on the other end. Couplings will be black anodized hard coated aluminum.

HOSE TROUGH
A quantity of one (1), hard suction hose trough(s) will be side sheet mounted on an adjustable bracket, located on the right side above the ladders.

Trough(s) will be constructed of aluminum painted job color.

The hose(s) will be held in place by hook and loop straps.

A low level strainer will be attached to the hard suction hose. The brand and model of the attached strainer will be Per order. A trough and strap will also be provided to secure the low level strainer.

HANDRAILS
The handrails will be 1.25" diameter knurled aluminum to provide a positive gripping surface.

Chrome plated end stanchions will support the handrail. Plastic gaskets will be used between end stanchions and any painted surfaces.

Drain holes will be provided in the bottom of all vertically mounted handrails.

Handrails will be provided to meet current edition of applicable NFPA standards. The handrails will be installed as noted on the sales drawing.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 77 of 115

HANDRAILS
One (1) vertical handrail will be located on each rear beavertail.

HANDRAIL
One (1) full width horizontal knurled aluminum handrail will be provided below the hose bed at the rear of the apparatus.

ADDITIONAL HANDRAIL
One (1) handrail, 10.00" long, will be mounted Driver side front top of side sheet . The handrail will be constructed out of knurled aluminum.

AIR BOTTLE STORAGE (SINGLE)
A quantity of one air bottle compartment, approximately 7.50" wide x 7.50" tall x 26.00" deep, will be provided on the driver side rearward of the rear wheels. The triangular door will cover the air bottle opening, the DEF tank access, and fuel fill. The compartment will be square with angled corners. A polished stainless steel door with a chrome plated flush lift & turn latch will be provided to contain the air bottle. A dielectric barrier will be provided between the door hinge, hinge fasteners and the body sheet metal.

Inside the compartment, black rubber matting will be provided.

AIR BOTTLE COMPARTMENT STRAP
A strap will be provided in the air bottle compartment to help contain the air bottle when the vehicle is parked on an incline. The strap will wrap around the neck and attach to the wall of the compartment.

AIR PACK STORAGE
A total of three (3) air pack compartment(s) will be provided and located on the left side forward of the rear wheels, on the right side forward of the rear wheels and on the right side rearward of the rear wheels. The air pack compartment(s) will be tapered to match the profile of the space available in the fender. The compartment(s) will be approximately 15.50" wide at the top and 5.00" wide at the bottom for the wheel cutout. The compartment(s) will be 15.50" tall at the body side compartment and 6.00" tall at the wheel cutout. The compartment(s) will be 26.00" deep and have a drain hole.

Inside the compartment, black Dura-Surf friction reducing material will be provided.

A polished stainless steel hinged door with a chrome plated flush lift & turn latch will be provided to contain the air pack. A dielectric barrier will be provided between the door hinge, hinge fasteners and the body sheet metal.

AIR BOTTLE STORAGE BIN
A storage bin will be provided for storage of three (3) air bottles. This storage bin will be installed Floor mount in RS2 compartment. Each separate air bottle storage compartment will be 7.50" square x

23.00" deep. The storage bin will be formed out of aluminum and the flooring lined with Dura-surf.

EXTENSION LADDER PROVIDED BY FIRE DEPARTMENT
There will be one (1) 24', two (2) section, wood, Alaco Series 2300-24 provided and installed by the fire department.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 78 of 115
If using an existing ladder, the following dimensions, including any bolts, pulleys, ropes, butt spurs, etc, are required:
• stored overall length
• overall width
• banking thickness
The dimensions are TO BE CONFIRMED AT PRE-CONSTRUCTION.

If dimensions aren't provided, the mounting provided will accommodate ladders sized per Alaco standard dimensions.

This ladder is non compliant to NFPA 1931, Chapter 4.4.3.1, "Standard on Design of and Design Verification Tests for Fire Department Ground Ladders".

Per Fire Department specification request of this ladder, the apparatus will be non compliant to the current edition of applicable NFPA standards at time of contract execution.

ROOF LADDER PROVIDED BY FIRE DEPARTMENT
There will be one (1) 14' roof, Alaco Series 2304-14 ladder(s) will be provided by the fire department.

The outside width of the ladder will be 14.00" wide.

If using an existing ladder, the following dimensions, including any bolts, pulleys, ropes, butt spurs, etc, are required:
• stored overall length
• overall width
• banking thickness
The dimensions are TO BE CONFIRMED AT PRE-CONSTRUCTION.

If dimensions aren't provided, the mounting provided will accommodate ladders sized per Alaco standard dimensions.

This ladder is non compliant to NFPA 1931, Chapter 4.2.2, "Standard on Design of and Design Verification Tests for Fire Department Ground Ladders".

Per Fire Department specification request of this ladder, the apparatus will be non compliant to the current edition of applicable NFPA standards at time of contract execution.

LADDER BRACKETS
The ladders will be installed on the right side of the hose body in lined brackets and held in place by steel chrome plated, quarter-turn spring loaded clamps with stainless steel rods. The clamps will be such that when the roof ladder is removed, the clamps can be moved a half turn to hold the extension ladder in place. The ladder brackets will be adjustable up and down. The ladder brackets will be spaced at 75.50" on center, 20.00" from the front edge of the body side sheet and 17.75" off the catwalk, to hold Alaco wood ladders.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 79 of 115

FOLDING LADDER PROVIDED BY FIRE DEPARTMENT
The folding ladder is not on the apparatus as manufactured. There will be one (1) 10' Alaco Model 2305-10 wood folding ladder provided by the fire department. The ladder will be installed in a stainless steel trough mounted above the ladders on the ladder brackets.

If using an existing ladder, the following dimensions, including any bolts, pulleys, ropes, butt spurs, etc, are required:
• stored overall length
• overall width
• banking thickness
The dimensions are TO BE CONFIRMED AT PRE-CONSTRUCTION
If dimensions aren't provided, the mounting provided will accommodate ladders sized per Alaco standard dimensions.

FOLDING LADDER STORAGE
One (1) folding ladder will be stored above the ladders on the ladder brackets in a stainless steel Ushaped trough.

SPACERS, NON-ABRASIVE, LADDER SUPPORTS
Four (4) nonabrasive ladder support spacers will be provided on the catwalk below the ladders. These spacers are to be evenly spaced and design to relieve stress from the ladder brackets and provide protection to the ladders from the aluminum treadplate on the catwalks.

BACKBOARD STORAGE
A transverse area over the pump and rearward of the crosslays will hold one (1) storage trough.

A blister will be supplied at each side to enclose the backboards due to their length.

The backboards will be accessible from either side of the vehicle through the aluminum treadplate door(s) with a pair of lift and turn latches. The door(s) will be hinged along the rearward edge.

The size of the backboard(s) to be stored will be 72.00" long x 16.00" wide x 3.00" high. 10' PIKE POLE
One (1) pike pole 10' long Duo Safety with a fiberglass handle, will be provided. 6' PIKE POLE
One (1) pike pole, 6' long DUO Safety with a fiberglass "D" handle will be provided.

PIKE POLE STORAGE
Aluminum tubing will be used for the storage of one (1) pike pole and will be located Behind ladders on side sheet above the other tubes. . If the head of a pike pole can come in contact with a painted surface, a stainless steel scuffplate will be provided. The pike pole tube will be notched to allow a New York style pike pole to fit into the tube.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 80 of 115

PIKE POLE STORAGE
Aluminum tubing will be used for the storage of one (1) pike pole and will be located mounted behind the ladders on the side sheet, passenger's side. If the head of a pike pole can come in contact with a painted surface, a stainless steel scuffplate will be provided.

PIKE POLE STORAGE
Aluminum tubing will be used for the storage of one (1) pike pole and will be located inside of the ladder brackets. See photo's . If the head of a pike pole can come in contact with a painted surface, a stainless steel scuffplate will be provided. A slot will be provided in the tube to store "D" handle pike pole.

BELL
A chrome plated, 12.00" bronze cast bell, complete with an eagle, will be mounted on the passenger side radiused corner of cab face. The cab will be properly reinforced to support the weight of the bell, the reinforcement bracket allow the bell to mount toward the upper corner of the windshield. A rope pull, for the bell, will be installed inside the cab.

INDICATOR LAMP LABEL
There will be a label provided on the back side of the sun visor located driver side. The label will provide brief descriptive text for each indicator lamp that may become visible in the driver side gauge cluster.

FOLDING STEPS FRONT OF BODY
Folding steps will be provided full height on the left side body compartments to provide access to the cargo bed. Steps will be spaced evenly on the sales drawing. Actual quantity may vary due to pump panel interferences but will meet the NFPA required maximum stepping height.

The Trident steps will be bright finished, non-skid with a luminescent tread coating, that is rechargeable from any light source and can hold a charge for up to 24 hours, on the stepping surface.

The step will incorporate an LED light to illuminate the stepping surface.

The steps can be used as a hand hold with two openings wide enough for a gloved hand.

REAR FOLDING STEPS
Bright finished, non-skid folding steps with a luminescent tread coating, that is rechargeable from any light source and can hold a charge for up to 24 hours, on the stepping surface will be provided at the rear. Each step will incorporate an LED light to illuminate the stepping surface. The steps can be used as a hand hold with two openings wide enough for a gloved hand.

One (1) additional folding step will be located one (1) PS rear body.. The step(s) will be bright finished, non-skid with a luminescent tread coating, that is rechargeable from any light source and can hold a charge for up to 24 hours, on the stepping surface. Each step will incorporate an LED light to illuminate the stepping surface. The step(s) can be used as a hand hold with two openings wide enough for a gloved hand.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 81 of 115
There will be one (1) bright aluminum treadplate cover/step/s provided and installed driver side rearward cargo area within the cargo area over the pump. The step will be reinforced for walking.

PUMP COMPARTMENT
The pump compartment will be separate from the hose body and compartments so that each may flex independently of the other. It will be a fabricated assembly of steel tubing, angles and channels which supports both the fire pump and the side running boards.

The pump compartment will be mounted on the chassis frame rails with rubber biscuits in a four point pattern to allow for chassis frame twist.

Pump compartment, pump, plumbing and gauge panels will be removable from the chassis in a single assembly.

PUMP MOUNTING
Pump will be mounted to a substructure which will be mounted to the chassis frame rail using rubber isolators. The mounting will allow chassis frame rails to flex independently without damage to the fire pump.

PUMP CONTROL PANELS (LEFT SIDE CONTROL)
All pump controls and gauges will be located at the left side of the apparatus and properly identified.

Layout of the pump control panel will be ergonomically efficient and systematically organized.

The pump operator's control panel will be removable in two (2) main sections for ease of maintenance:

The upper section will contain sub panels for the mounting of the pump pressure control device, engine monitoring gauges, electrical switches, and foam controls (if applicable). Sub panels will be removable from the face of the pump panel for ease of maintenance. Below the sub panels will be located all valve controls and line pressure gauges.

The lower section of the panel will contain all inlets, outlets, and drains.

All push/pull valve controls will have 1/4 turn locking control rods with polished chrome plated zinc tee handles. Guides for the push/pull control rods will be chrome plated zinc castings securely mounted to the pump panel. Push/pull valve controls will be capable of locking in any position. The control rods will pull straight out of the panel and will be equipped with universal joints to eliminate binding.

IDENTIFICATION TAGS
The identification tag for each valve control will be recessed in the face of the tee handle.

All discharge outlets will have color coded identification tags, with each discharge having its own unique color. Color coding will include the labeling of the outlet and the drain for each corresponding discharge.

All line pressure gauges will be mounted directly above the corresponding discharge control tee handles and recessed within the same chrome plated casting as the rod guide for quick identification.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 82 of 115
The gauge and rod guide casting will be removable from the face of the pump panel for ease of maintenance. The casting will be color coded to correspond with the discharge identification tag.

All remaining identification tags will be mounted on the pump panel in chrome plated bezels.

The pump panel on the right side will be removable with lift and turn type fasteners.

Trim rings will be installed around all inlets and outlets.

CARGO FLOOR, SPLIT
The bright aluminum treadplate flooring in the cargo compartment will be split into two (2) or more pieces for easier access to the pump and plumbing without removing any other items and will support the weight of a fire fighter.

GUARD
An aluminum treadplate guard shall be provided around the electric deck gun control. The guard shall be open at the top to operate the switch.

PUMP
Pump will be a Waterous CSU, 1500 gpm single (1) stage midship mounted centrifugal type.

Pump will be the class "A" type.

Pump will deliver the percentage of rated discharge at pressures indicated below:
• 100 percent of rated capacity at 150 psi net pump pressure. • 70 percent of rated capacity at 200 psi net pump pressure. • 50 percent of rated capacity at 250 psi net pump pressure.

Pump body will be close-grained gray iron, bronze fitted, and horizontally split in two (2) sections for easy removal of the entire impeller shaft assembly (including wear rings).

Pump will be designed for complete servicing from the bottom of the truck, without disturbing the pump setting or apparatus piping.

Pump case halves will be bolted together on a single horizontal face to minimize chance of leakage and facilitate ease of reassembly. No end flanges will be used.

Discharge manifold of the pump will be cast as an integral part of the pump body assembly and will provide a minimum of three (3) 3.50" openings for flexibility in providing various discharge outlets for maximum efficiency.

The three (3) 3.50" openings will be located as follows: one (1) outlet to the right of the pump, one (1) outlet to the left of the pump, and one (1) outlet directly on top of the discharge manifold.

Impeller shaft will be stainless steel, accurately ground to size. It will be supported at each end by sealed, anti-friction ball bearings for rigid precise support. Impeller will have flame plated hubs assuring maximum pump life and efficiency despite any presence of abrasive matter in the water supply.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 83 of 115
Bearings will be protected from water and sediment by suitable stuffing boxes, flinger rings, and oil seals. No special or sleeve type bearings will be used.

Pump will be equipped with a self-adjusting, maintenance-free, mechanical shaft seal.

The mechanical seal will consist of a flat, highly polished, spring fed carbon ring that rotates with the impeller shaft. The carbon ring will press against a highly polished stainless steel stationary ring that is sealed within the pump body.

In addition, a throttling ring will be pressed into the steel chamber cover, providing a very small clearance around the rotating shaft in the event of a mechanical seal failure. The pump performance will not deteriorate, nor will the pump lose prime, while drafting if the seal fails during pump operation.

Wear rings will be bronze and easily replaceable to restore original pump efficiency and eliminate the need to replace the entire pump casing due to wear.

PUMP TRANSMISSION
The pump transmission will be made of a three (3) piece, aluminum, horizontally split casing. Power transfer to pump will be through a high strength Morse HY-VO silent drive chain. By the use of a chain rather than gears, 50% of the sprocket will be accepting or transmitting torque, compared to two (2) or three (3) teeth doing all the work.

Drive shafts will be 2.35" diameter hardened and ground alloy steel and supported by ball bearings.

The case will be designed to eliminate the need for water cooling.

PUMPING MODE
An interlock system will be provided to ensure that the pump drive system components are properly engaged so that the apparatus can be safely operated. The interlock system will be designed to allow stationary pumping only.

AIR PUMP SHIFT
Pump shift engagement will be made by a two (2) position sliding collar, actuated pneumatically (by air pressure), with a three (3) position air control switch located in the cab. A manual back-up shift control will also be located on the left side pump panel.

Two (2) indicator lights will be provided adjacent to the pump shift inside the cab. One (1) green light will indicate the pump shift has been completed and be labeled "pump engaged". The second green light will indicate when the pump has been engaged, and that the chassis transmission is in pump gear.

This indicator light will be labeled "OK to pump".

The pump shift will be interlocked to prevent the pump from being shifted out of gear when the chassis transmission is in gear to meet NFPA requirements.

The pump shift control in the cab will be illuminated to meet NFPA requirements.

TRANSMISSION LOCK-UP
The direct gear transmission lock-up for the fire pump operation will engage automatically when the pump shift control in the cab is activated.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 84 of 115

AUXILIARY COOLING SYSTEM
A supplementary heat exchange cooling system will be provided to allow the use of water from the discharge side of the pump for cooling the engine water. The heat exchanger will be a separate unit. It will be installed in the pump or engine compartment with the control located on the pump operator's control panel. The exchanger will be plumbed to the master drain valve.

PUMP INTAKE RELIEF VALVE
An Akron Style 53 relief valve will be installed on the suction side of the pump preset at 125 psig.

The relief valve will have a working range of 50 psi to 250 psi.

The outlet will terminate below the frame rails with a 2.50" National Standard hose thread adapter and will have a "do not cap" warning tag.

The relief valve pressure control will be located behind the right side pump panel with a stainless steel access door.

PIERCE PRESSURE CONTROLLER
A Pierce electronic pressure controller will be provided.

A pressure transducer will be installed in the discharge side of the water pump. The transducer continuously monitors pump pressure sending a signal to the electronic pressure controller.

The pressure controller can be used in two (2) modes of operation, RPM mode and pressure modes.

The controller will be programmed to turn on/default to No Mode/Default Press Setting mode.

In the RPM mode, the controller can be activated after vehicle parking brake has been set. When in this mode, the controller will maintain the set engine speed, regardless of engine load (within engine operation capabilities).

In the pressure mode, the controller can be activated after vehicle parking brake has been set. When in this mode, the controller will automatically maintain the discharge pressure set by the operator (within the discharge capabilities of the pump and water supply) regardless of flow.

A 2.00" diameter throttle control knob with no mechanical stops, a serrated grip, and a red idle push button in the center will be a integrated/part of the pressure controller. The throttle control knob will be programmed for Clockwise rotation to increase engine speed.

Individual LED indicators for ok to pump, throttle ready, pressure mode and rpm mode will be located on the pressure controller for easy viewing.

A pump cavitation protection feature will also be provided which will return the engine to idle should the pump cavitate. Cavitation is sensed by the combination of pump pressure below 30 psi and engine speed above 2000 rpm for more than five (5) seconds.

Other safety features include recognition of low water and no water conditions with an automatic programmed response and a push button to return the engine to idle.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 85 of 115
The pressure controller LCD screen will be 4.20" in size with a minimum brightness of 750 nits. The LCD screen and LED intensity will be automatically adjust for day and nighttime operation. The LCD screen intensity can also be manually adjusted if needed.

The following information will be provided/displayed on the LCD screen - • Engine RPM
• Check engine and stop engine warning indicators
• Engine oil pressure
• Engine coolant temperature
• Water pump transmission temperature
• Fuel Level
• Water tank level
• Battery voltage
• Operating mode (RPM or pressure)
• Pressure or RPM setting
On screen messaging show diagnostic and warning messages as they occur. It will show apparatus information, stored data, and program options when selected by the operator. It will monitor inputs outputs and support audible and visual warning alarms for the following conditions - • High battery voltage
• Low battery voltage/engine off
• Low battery voltage/engine running
• High water pump temperature
• Low fuel
• Low engine oil pressure
• High engine coolant temperature
• Water tank out of water (visual alarm only)
• No engine response (visual alarm only)
The pressure controller will store the accumulated operating hours for the pump and engine. These items are to be displayed within the pressure controller menu.

The pressure controller will include a USB port on the back of the controller for easy software upgrades if needed.

PRIMING PUMP
The priming pump will be a Trident Emergency Products compressed air powered, high efficiency, multistage venturi based AirPrime System, conforming to standards outlined in the current edition of applicable NFPA standards.

All wetted metallic parts of the priming system are to be of brass and stainless steel construction.

One (1) priming control will open the priming valve and start the pump primer.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 86 of 115

RECIRCULATING LINE WITH CHECK VALVE
A 0.50" diameter recirculating line, from the pump to the water tank, will be furnished with a control installed at the pump operator's control panel. A check valve will be provided in this line to prevent the back flow of water from the tank to the pump if the valve is left in the open position.

PUMP MANUALS
There will be a total of two (2) pump manuals provided by the pump manufacturer and furnished with the apparatus. The manuals will be provided by the pump manufacturer in the form of two (2) electronic copies. Each manual will cover pump operation, maintenance, and parts.

PLUMBING, STAINLESS STEEL AND HOSE
All inlet and outlet lines will be plumbed with either stainless steel pipe, flexible polypropylene tubing or synthetic rubber hose reinforced with hi-tensile polyester braid. All hose's will be equipped with brass or stainless steel couplings. All stainless steel hard plumbing will be a minimum of a schedule 10 wall thickness.

Where vibration or chassis flexing may damage or loosen piping or where a coupling is required for servicing, the piping will be equipped with victaulic or rubber couplings.

Plumbing manifold bodies will be ductile cast iron or stainless steel.

All piping lines are to be drained through a master drain valve or will be equipped with individual drain valves. All drain lines will be extended with a hose to drain below the chassis frame.

All water carrying gauge lines will be of flexible polypropylene tubing.

All piping, hose and fittings will have a minimum of a 500 PSI hydrodynamic pressure rating.

FOAM SYSTEM PLUMBING
All piping that is in contact with the foam concentrate or foam/water solution will be stainless steel. The fittings will be stainless steel or brass. Cast iron pump manifolds will be allowed.

MAIN PUMP INLETS
A 6.00" pump manifold inlet will be provided on each side of the vehicle. The suction inlets will include removable die cast zinc screens that are designed to provide cathodic protection for the pump, thus reducing corrosion in the pump.

SHORT SUCTION TUBE(S)
The suction tube(s) on the water pump will have short suction tube(s) installed to allow for installation of adapters, elbows or intake valves without excessive overhang.

MAIN PUMP INLET CAP PROVIDED BY FIRE DEPARTMENT
NFPA 1900, 2024 edition, section 13.6.8 requires all intakes to be provided with caps or closures capable of withstanding a hydrostatic gauge pressure of 500 psi (3400 kPa).

The caps are not on the apparatus as manufactured. The fire department will provide both caps for the main pump inlets.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 87 of 115
VALVES
There will be Eleven (11) Waterous 2.50" full flow valves. The valves will be used No. 1 left side discharge, No. 2 left side discharge, No. 1 right side discharge, No. 2 right side discharge, No. 3 right side discharge, No. 1 crosslay, No. 2 crosslay, No.1 rear discharge, No. 1 rear pre-connect discharge, hose reel and tank fill .

The Waterous full flow valve will have a 2.50" chromium plated bronze ball forming a hard, durable surface. There will be a hydraulically balanced floating seal assembly that will be self adjusting for wear.

If Waterous valves are desired for outlets 3.00" and larger, that valve will be picked within the specific outlet category.

All remaining discharge valves and auxiliary inlets will be Akron Unibody valves with a stainless-steel ball and a simple two-seat design. No lubrication or regular maintenance is required on the valve.

If an outlet location chosen from above uses a valve smaller than 2.50", that valve will be substituted with a Waterous 2.50" full flow valve. This option will supersede any specific outlet category option that requires a valve smaller than 2.50".

The location of the valve for the two (2) inlets will be recessed behind the pump panel.

INLET CONTROL
The side auxiliary inlet(s) will incorporate a quarter-turn ball valve with the control located at the inlet valve. The valve operating mechanism will indicate the position of the valve.

LEFT SIDE INLET
There will be one (1) auxiliary inlet with a 2.50" valve at the left side pump panel, terminating with a

2.50" (F) National Standard hose thread adapter.

The auxiliary inlet will be provided with a strainer, chrome swivel and plug.

RIGHT SIDE INLET
There will be one (1) auxiliary inlet with a 2.50" valve at the right side pump panel, terminating with a

2.50" (F) National Standard hose thread adapter.

The auxiliary inlet will be provided with a strainer, chrome swivel and plug.

INLET BLEEDER VALVE
A 0.75" bleeder valve will be provided for each side gated inlet.

The valves will be located behind the panel with a "T" swing style handle control extended to the outside of the panel.

The handles will be chrome plated and provide a visual indication of valve position. The swing handle will provide an ergonomic position for operating the valve without twisting the wrist and provides excellent leverage.

The water discharged by the bleeders will be routed below the chassis frame rails.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 88 of 115

TANK TO PUMP
The booster tank will be connected to the intake side of the pump with heavy duty piping and a quarter turn 3.00" full flow line valve with the control remotely located at the operator's panel. The tank to pump line will run straight (no elbows) from the pump into the front face of the water tank and down into the tank sump. A rubber coupling will be included in this line to prevent damage from vibration or chassis flexing.

The control on the pump panel will be "in" when the valve is open and "out" when the valve is closed.

A check valve will be provided in the tank to pump supply line to prevent the possibility of "back filling" the water tank.

TANK REFILL
A 1.50" combination tank refill and pump re-circulation line will be provided, using a quarter-turn full flow ball valve controlled from the pump operator's panel.

DISCHARGE OUTLET CONTROLS
The discharge outlets will incorporate a quarter-turn ball valve with the control located at the pump operator's panel. The valve operating mechanism will indicate the position of the valve.

If a handwheel control valve is used, the control will be a minimum of a 3.9" diameter stainless steel handwheel with a dial position indicator built in to the center of the handwheel.

Any 3.00 inch or larger discharge valve will be a slow-operating valve in accordance with NFPA

16.7.5.3. LEFT SIDE DISCHARGE OUTLETS
There will be Two (2) discharge outlets with a 2.50" valve on the left side of the apparatus, terminating with a 2.50" (M) National Standard hose thread adapter.

LEFT SIDE OUTLET ELBOWS
The 2.50" discharge outlets located on the left side pump panel will be furnished with a 2.50" (F) National Standard hose thread x 2.50" (M) National Standard hose thread, chrome plated, 45 degree elbow.

The elbow will be Pierce VLH, which incorporates an exclusive thread design to automatically relieve stored pressure in the line when disconnected.

RIGHT SIDE DISCHARGE OUTLETS
There will be Two (2) discharge outlets with a 2.50" valve on the right side of the apparatus, terminating with a 2.50" (M) National Standard hose thread adapter.

RIGHT SIDE OUTLET ELBOWS
The 2.50" discharge outlets located on the right side pump panel will be furnished with a 2.50" (F) National Standard hose thread x 2.50" (M) National Standard hose thread, chrome plated, 45 degree elbow.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 89 of 115
The elbow will be Pierce VLH, which incorporates an exclusive thread design to automatically relieve stored pressure in the line when disconnected.

There will be One (1) discharge outlet with a 3.00" valve on the right side of the apparatus, terminating with a 3.00" (M) National Standard hose thread adapter.

Any 3.00 inch or larger discharge valve will be a slow-operating valve in accordance with NFPA

13.7.5.3. ADDITIONAL RIGHT SIDE OUTLET ELBOWS PROVIDED BY FIRE DEPARTMENT NFPA 1900, 2024 edition, section 13.7.7 requires any 2.00" or larger discharge outlet that is located more than 42.00" off the ground and to which hose is to be connected and that is not in a hose storage area will be supplied with a sweep elbow of at least 30 degrees downward.

NFPA 1900, 2024 edition, section 13.7.4 requires all discharge outlet connections, except connections to which a hose will be pre-connected, will be equipped with caps or closures capable of withstanding a hydrostatic gauge pressure of 100 psi over the maximum pump close-off pressure or 500 psi, whichever is greater.

The elbow(s) and cap are not on the apparatus as manufactured. The fire department will provide the elbow(s) and cap.

FRONT DISCHARGE OUTLET
There will be one (1) 1.50" discharge outlet piped to the front of the apparatus and located on the top of the right side of the front bumper.

Plumbing will consist of 2.00" piping and flexible hose with a 2.00" ball valve with control at the pump operator's panel. A fabricated weldment made of stainless steel pipe will be used in the plumbing where appropriate. The piping will terminate with a 1.50" NST with 90 degree stainless steel swivel.

There will be Elkhart push pull drains provided at all low points of the piping.

REAR DISCHARGE OUTLET
There will be Two (2) discharge outlets piped to the rear of the hose bed, one (1) each side, installed so proper clearance is provided for spanner wrenches or adapters. Plumbing will consist of 2.50" piping along with a 2.50" full flow ball valve with the control from the pump operator's panel.

REAR OUTLET ELBOWS
The 2.50" discharge outlets located at the rear of the apparatus will be furnished with a 2.50" (F) National Standard hose thread x 2.50" (M) National Standard hose thread, chrome plated, 45 degree elbow.

The elbow will be Pierce VLH, which incorporates an exclusive thread design to automatically relieve stored pressure in the line when disconnected.

FRONT OF HOSE BED DISCHARGE OUTLET
There will be One (1) discharge outlet discharge(s) piped to the front of the hose bed and located passemnger's side . Plumbing will consist of 2.50" piping with a 2.50" full-flow ball valve controlled at DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 90 of 115
the pump operator's panel. The discharge(s) will terminate with a 2.50" (M) National Standard hose thread adapter.

DISCHARGE CAPS/ INLET PLUGS
Chrome plated, rocker lug, caps with chain will be furnished for all discharge outlets 1.00" thru 3.00" in size, besides the pre-connected hose outlets.

Chrome plated, rocker lug, plugs with chain will be furnished for all auxiliary inlets 1.00" thru 3.00" in size.

The caps and plugs will incorporate a thread design to automatically relieve stored pressure in the line when disconnected.

OUTLET BLEEDER VALVE
A 0.75" bleeder valve will be provided for each outlet 1.50" or larger. Automatic drain valves are acceptable with some outlets if deemed appropriate with the application.

The valves will be located behind the panel with a T swing style handle control extended to the outside of the side pump panel.

The handles will be chrome plated and provide a visual indication of valve position.

The T swing handle will provide an ergonomic position for operating the valve without twisting the wrist and provides excellent leverage.

Bleeders will be located at the bottom of the pump panel. They will be properly labeled identifying the discharge they are plumbed in to.

The water discharged by the bleeders will be routed below the chassis frame rails.

DELUGE RISER
A 3.00" deluge riser will be installed above the pump in such a manner that a monitor can be mounted and used effectively. Piping will be installed securely so no movement develops when the line is charged. This outlet will be located in the cargo area.

The riser will be gated with an electrically actuated 3.00" valve. The valve will be controlled by two (2) Akron 9333 electric valve controllers. One (1) will be provided on the pump operators panel and one (1) will be located near the deluge riser in the cargo area. The electric controls must be of a true position feedback design, requiring no clutches in the motor or current limiting. The units must be completely sealed with momentary open, close as well and an optional one touch full open feature to operate the valve actuator. The controllers will provide position indication on a full color, backlit LCD display. They will have manual adjustment of the brightness as well as an auto dimming option.

TELESCOPIC PIPING
The deluge riser piping will include a manual Task Force Tips XG18 extend-a-gun extension. This extension will be telescopic to allow the deluge gun to be raised 18.00" increasing the range of operation.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 91 of 115
A position sensor will be provided on the telescopic piping that will activate the "do not move vehicle" light inside the cab when the monitor is in the raised position.

The deluge riser controller unit will be located locate as high as possible in the cargo area (not on the support tubing). See photos or final inspection document of previous job #28474.

MONITOR
A customer/dealer supplied and installed make and model Akron Apollo model 3416 with a TFT Extend-A-Gun mount monitor will be properly installed on the deluge riser.

The deluge riser will have a 3.00" four (4)-bolt flange for mounting the monitor.

CROSSLAY HOSE BEDS, 1.50"
Two (2) crosslays with 1.50" outlets will be provided. Each bed to be capable of carrying 7.00" clear openings for each crosslay. The chicksan swivel connection for the forward most crosslay must be located on the PS. The chicksan swivel connection for the rearward most crosslay must be located on the DS and will be plumbed with 2.00" i.d. pipe and gated with a 2.00" quarter turn ball valve.

Outlets to be equipped with a 1.50" National Standard hose thread 90 degree swivel located in the hose bed so that hose may be removed from either side of apparatus.

The crosslay controls will be at the pump operator's panel.

The center crosslay dividers will be fabricated of .25" aluminum and will provide adjustment from side to side. The divider will be unpainted with a brushed finish.

Vertical scuffplates, constructed of stainless steel, will be provided at the front and rear ends of the bed on each side of vehicle.

Crosslay bed flooring will consist of removable perforated brushed aluminum.

CROSSLAY HOSE RESTRAINT
A black 1.00" nylon webbing design restraint will be provided across the ends of two (2) crosslay(s) to secure the hose during travel. The webbing assembly is to be attached at the back side of the hosebed opening with footman loops and straps to loop through the footman loops and latch with cam lock buckles. The webbing will be permanently attached at the front of the hosebed opening between the cab and pump house.

A pair of nylon 2.00" black straps will be secured to the top of the crosslay opening, front to back.

Footman loops will be provided at the front and back side of the opening with Velcro fasteners at the center of the straps. Straps will be positioned so that the they can be opened while standing on the running boards on each side of the apparatus.

CROSSLAY LOCATION
The crosslays will be located to the rear of the telescopic light.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 92 of 115

BOOSTER HOSE REEL
A Hannay electric rewind booster hose reel will be installed over the pump in a recessed open compartment on the right side of the apparatus. The reel will be fabricated of aluminum and have highly polished end discs.

A polished stainless steel roller and guide assembly will be mounted on the reel side of the apparatus.

Discharge control will be provided at the pump operator's panel. Plumbing to the reel will consist of

1.50" Aeroquip hose and a 1.50" valve.

The reel will include NPSH threaded couplings.

Reel motor will be protected from overload with a sized automatic reset circuit breaker.

Three (3) electric rewind control switches will be provided. One (1) will be installed on the officer's side pump panel and two (2) will be installed at the top inside rear corners of the cargo area, one (1) on each side.

Capacity of the hose reel will be 150 feet of 1.00" booster hose.

A check valves will be installed in the hose reel plumbing. A .75" drain will be provided to release the pressure.

HOSE REEL SPROCKET AND DISC
The sprocket on the hose reel will be cadium plated and the discs of the reel will be polished stainless steel.

HOSEREEL ACCESS
A cutout will be provided in the side sheet next to the booster hose reel. This cutout will allow access to the hose and provide a window to view the reel. Stainless steel trim will be mounted horizontally and vertically around the cutout.

There will be one (1) additional polished stainless steel roller and guide assembly mounted opposite of the reel.

PUSH BUTTON SWITCH, REEL
Two (2) push button switches will be installed on the side wall of the cargo compartment on the outward facing left side and right side. The push button will be spaced 1.00" down from the top of the side sheet flange.

HUSKY 3 FOAM PROPORTIONER
A Pierce Husky® 3 foam proportioning system will be provided. The Husky 3 is an on demand, automatic proportioning, single point, direct injection system suitable for all types of Class A and B foam concentrates, including the high viscosity (6000 cps), alcohol resistant Class B foams. Operation will be based on direct measurement of water flow, and remain consistent within the specified flows and pressures. The system will automatically proportion foam solution at rates from .1 percent to 3 percent regardless of variations in water pressure and flow, up to the maximum rated capacity of the foam concentrate pump.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 93 of 115
The design of the system will allow operation from draft, hydrant, or relay operation.

System Capacity
The system will have the ability to deliver the following minimum foam solution flow rates at accuracies that meet or exceed NFPA requirements at a pump rating of 150 psi. • 100 gpm @ 3 percent
• 300 gpm @ 1 percent
• 600 gpm @ 0.5 percent
Class A foam setting in 0.1 percent increments from 0.1 percent to 1 percent. Typical settings of 1 percent, 0.5 percent and 0.3 percent (maximum capacity will be limited to the plumbing and water pump capacity).

Control System
The system will be equipped with a digital electronic control display located on the pump operator's panel. Push button controls will be integrated into the panel to turn the system on/off, control the foam percentage, and to set the operation modes.

The percent of injection will have a preset. This preset can be changed at the fire department as desired. The percent of injection will be able to be easily changed at the scene to adjust to changing demands.

Three (3) .50 tall LEDs will display the foam percentage in numeric characters. Three (3) indicator LEDs will also be included, one (1) green, one (1) red, and one (1) yellow. The LEDs will indicate various system operation or error states.

The indications will be:
• Solid Green - System On
• Solid Red - Valve Position Error
• Solid Yellow - Priming System
• Flashing Green - Injecting Foam
• Flashing Red - Low Tank Level
• Flashing Yellow - Refilling Tank
The control display will house a microprocessor, which receives input from the systems water flow meter while also monitoring the position of the foam concentrate pump. The microprocessor will compare the values of the water flow versus the position/rate of the foam pump, to ensure the proportion rate is accurate. One (1) check valve will be installed in the plumbing to prevent foam from contaminating the water pump.

Hydraulic Drive System
The foam concentrate pump will be powered by an electric over hydraulic drive system. The hydraulic system and motor will be integrated into one (1) unit.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 94 of 115
Foam Concentrate Pump
The foam concentrate pump will be of positive displacement, self-priming; linear actuated design, driven by the hydraulic system. The pump will be constructed of brass body; chrome plated stainless steel shaft, with a stainless steel piston. In order to increase longevity of the pump, no aluminum will be present in its construction.

A relief system will be provided which is designed to protect the drive system components and prevent over pressuring the foam concentrate pump.

The foam concentrate pump will have minimum capacity for 3 gpm with all types of foam concentrates with a viscosity at or below 6000 cps including protein, fluoroprotein, AFFF, FFFP, or AR-AFFF. The system will deliver only the amount of foam concentrate flow required, without recirculating foam back to the storage tank. Recirculating foam concentrate back to the storage tank can cause agitation and premature foaming of the concentrate, which can result in system failure. The foam concentrate pump will be self-priming and have the ability to draw foam concentrate from external supplies such as drums or pails.

External Foam Concentrate Connection
An external foam pick-up will be provided to enable use of a foam agent that is not stored on the vehicle. The external foam pick-up will be designed to allow continued operation after the on-board foam tank is empty, or the use of foam different than the foam in the foam tank.

Panel Mounted External Pick-Up Connection / Valve
A bronze three (3)-way valve will be provided. The unit will be mounted to the pump panel. The valve unit will function as the foam system tank to pump valve and external suction valve. The external foam pick-up will be one (1) 0.75" male connection GHT (garden hose thread) with a cap.

Pick-Up Hose
A 0.75" flexible hose with an end for insertion into foam containers will be provided. The hose will be supplied with a 0.75" female swivel GHT (garden hose thread) swivel connector. The hose will be shipped loose.

Discharges
The foam system will be plumbed to the front of hose bed right side, hose reel in right side of dunnage area, front crosslay, rear crosslay, left side outlet and right side outlet.

System Electrical Load
The maximum current draw of the electric motor and system will be no more than 55 amperes at 12 VDC.

SINGLE FOAM TANK REFILL
The foam system's proportioning pump will be used to fill the foam tank. This will allow use of the auxiliary foam pick-up to pump the foam from pails or a drum on the ground into the foam tank. A foam shut-off switch will be installed in the fill dome of the tank to shut the system down when the tank is full.

The fill operation will be controlled by a mode in the foam system controller. While the proportioner pump is filling the tank, the controller will display a flashing yellow LED to indicate that the tank is filling.

When the tank is full, as determined by the float switch in the tank dome, the pump will stop and the DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 95 of 115
controller will shut the yellow LED off. If it attempted to use tank fill and the refill valve and suction valve are in the wrong position(s), then a red LED will illuminate to indicate the improper valve position(s). When the valves are positioned properly, then filling will commence.

RELOCATE HYDRAULIC RESERVOIR
The Husky 3 foam system hydraulic reservoir is typically located in the cargo area over the pump. The new location will be forward hosebed PS.

FOAM TANK
The foam tank will be an integral portion of the polypropylene water tank. The cell will have a capacity of 20 gallons of foam with the intended use of Class A foam. The foam cell will not reduce the capacity of the water tank. The foam cell will have a screen in the fill dome and a breather in the lid.

FOAM TANK DRAIN
The foam tank drain will be a 1.00" quarter turn drain valve located inside the pump/plumbing compartment.

The following drawing(s) will be provided for approval by the customer. The drawing(s) will be made to match 34048 similar Pierce job number.

PUMP OPERATOR'S PANEL DRAWING
A detailed drawing to scale of the pump operator's panel will be provided for the customer to review.

The drawing will include all of the gauges, controls, switching, etc.., located on the pump operator's panel. The customer will be allowed to make changes and/or mark-ups to this approval drawing. The fire apparatus manufacturer will make revisions (If needed) to the drawing per the customer changes and/or mark-ups as long as the changes are physically possible within a specific product line.

The finalized and signed customer approved pump operator's panel drawing will become part of the contract documents.

Due to the way drain(s), bleeder(s), operational/maintenance tag(s) and NFPA required warning tag(s) are placed on pump panel(s), these items will NOT be shown on any pump panel approval drawing(s).

These item(s) will be placed on pump panel(s) at the fire apparatus manufacturer discretion.

REMAINING PUMP PANEL(S)
Detailed drawing(s) to scale of the remaining pump panel(s) will be provided for the customer to review.

The drawing(s) will include all of the gauges, controls, switching, etc.., located on the pump panel(s).

The customer will be allowed to make changes and/or mark-ups to these approval drawing(s). The fire apparatus manufacturer will make revisions (If needed) to the drawing(s) per the customer changes and/or mark-ups as long as the changes are physically possible within a specific product line.

The finalized and signed customer approved pump panel drawing(s) will become part of the contract documents.

Due to the way drain(s), bleeder(s), operational/maintenance tag(s) and NFPA required warning tag(s) are placed on pump panel(s), these items will NOT be shown on any pump panel approval drawing(s).

These item(s) will be placed on pump panel(s) at the fire apparatus manufacturer discretion.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 96 of 115

COLOR CODED TAGS
A detailed drawing/chart of the colors used on all of the inlet(s) and outlet(s) will be provided for the customer to review. The customer will be allowed to make changes and/or mark-ups to this approval drawing/chart. The fire apparatus manufacturer will make revisions (If needed) to the drawing per the customer changes and/or mark-ups as long as the changes are physically possible within a specific product line.

The finalized and signed customer approved drawing/chart of the colors will become part of the contract documents.

SPECIAL TEXT/VERBIAGE TAGS
A detailed drawing/chart of the text/verbiage used on all of the inlet(s) and outlet(s) will be provided for the customer to review. The customer will be allowed to make changes and/or mark-ups to this approval drawing/chart. The fire apparatus manufacturer will make revisions (If needed) to the drawing per the customer changes and/or mark-ups as long as the changes are physically possible within a specific product line.

The finalized and signed customer approved drawing/chart of the text/verbiage will become part of the contract documents.

PUMP PANEL CONFIGURATION
The pump panel configuration will be arranged and installed in an organized manner that will provide user-friendly operation.

PUMP AND GAUGE PANEL
The pump and gauge panels will be constructed of aluminum with a black vinyl finish. A polished aluminum trim molding will be provided around each panel.

PUMP ACCESS
Right Side Panel
The right side pump panel will be removable.

Panel Fastener
The right side removable panel will be secured using a chrome flush lift and turn latch .

The left side pump panels will be attached with screws.

The right side lower panel (drain bank) will be secured using screws.

PUMP COMPARTMENT LIGHT
A pump compartment light will be provided inside the right side pump enclosure and accessible through a door on the pump panel.

A 0.125" weep hole will be provided in each light lens, preventing moisture retention.

Engine monitoring graduated LED indicators will be incorporated with the pressure controller.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 97 of 115

THROTTLE READY GREEN INDICATOR LIGHT
There will be a green indicator light integrated with the pressure governor and/or engine throttle installed on the pump operators panel that is activated when the pump is in throttle ready mode.

OK TO PUMP INDICATOR LIGHT
There will be a green indicator light installed on the pump operators panel that is activated when the pump is in Ok To Pump mode.

COMPARTMENT, CAB LIFT CONTROL PANEL
A compartment will be provided at the pump panel, right side. This compartment will be large enough to house the control panel for the cab lift. A stainless steel door will be provided.

PUMP PANEL INFORMATION
The cab lift door must be hinged toward the rear of the truck so that it does not hit the push up light pole. Ref. photo's for changes at PU to the PS panel. Mount Electric control valve as high as possible in the cargo area #7 on 31366.
switch order from top to bottom: PANEL LIGHTS, OK TO PUMP, DS FLOODLIGHT, PS FLOODLIGHT, PERIMETER LIGHTS.

There will be a switch at the pump operators panel that can deactivate the warning light in that vicinity.

This switch will only be active when the parking brake is applied and the pump is shifted into gear.

VACUUM AND PRESSURE GAUGES
The pump vacuum and pressure gauges will be liquid filled and manufactured by Class 1 Incorporated ©.

The gauges will be a minimum of 6.00" in diameter and will have white faces with black lettering, with a pressure range of 30.00"-0-600#.

The pump pressure and vacuum gauges will be installed adjacent to each other at the pump operator's control panel.

Test port connections will be provided at the pump operator's panel. One will be connected to the intake side of the pump, and the other to the discharge manifold of the pump. They will have 0.25 in. standard pipe thread connections and polished stainless steel plugs. They will be marked with a label.

PRESSURE GAUGES
The individual "line" pressure gauges for the discharges will be interlube filled and manufactured by Class 1©.

The gauges will be a minimum of 3.50" in diameter and will have white faces with black lettering.

Gauges will be compound type with a vacuum/pressure range of 30.00"-0-600#.

The individual pressure gauge will be installed as close to the outlet control as practical.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 98 of 115

WATER LEVEL GAUGE
An electric water level gauge will be incorporated in the pressure controller that registers water level by means of 9 LEDs. They will be at 1/8 level increments with a tank empty LED. The LEDs will be a bright type that is readable in sunlight, and have a full 180-degree of clear viewing.

To further alert the pump operator, the gauge will have a warning flash when the tank volume is less than 25%, and will have "Down Chasing LEDs when the tank is almost empty.

The level measurement will be ascertained by sensing the head pressure of the fluid in the tank or cell.

CLASS "A" FOAM LEVEL GAUGE
A Fire Research TankVision Pro model WLA360-A00 cell/tank level indicator kit will be installed behind pump panel in DS front corner on a bracket so gauge can be serviced and calibrated . The kit will include an electronic indicator module, a pressure sensor, a 10' sensor cable and a tank vent. The indicator will show the volume of Class "A" foam concentrate in the cell/tank on nine (9) easy to see super bright RGB LEDs. A wide view lens over the LEDs will provide for a viewing angle of 180 degrees. The indicator case will be waterproof, manufactured of Polycarbonate/Nylon material and have a distinctive green label.

The program features will be accessed from the front of the indicator module. The program will support self-diagnostics capabilities, self-calibration, six (6) programmable colored light patterns to display cell/tank volume, adjustable brightness control levels and a data link to connect remote indicators. Low foam level warnings will include flashing LEDs at 1/4 cell/tank and down chasing LEDs when the cell/tank is almost empty.

The indicator will receive an input signal from an electronic pressure sensor. The sensor will be mounted from the outside of the foam cell/tank near the bottom. No probe will be placed on the interior of the cell/tank. Wiring will be weather resistant and have automotive type plug-in connectors.

CLASS "A" MINI SLAVE UNIT
Fire Research TankVision model WLA265-A00 miniature cell/tank indicator will be installed on DS pump panel to the left of the pressure governor. top of gauge to be in line with discharges . The indicator will show the volume of Class "A" foam concentrate in the cell/tank on five (5) easy to see super bright LEDs. A wide view lens over the LEDs will provide for a viewing angle of 180 degrees. The indicator case will be manufactured of Polycarbonate material with an integrated lens and have a distinctive green label.

LIGHT SHIELD
There will be a polished, 16 gauge stainless steel light shield installed over the pump operator's panel. • There will be 12 volt DC white LED lights installed under the stainless steel light shield to illuminate the controls, switches, essential instructions, gauges, and instruments necessary for the operation of the apparatus. These lights will be activated by the pump panel light switch.

Additional lights will be included every 18.00" depending on the size of the pump house. • One (1) pump panel light will come on when the pump is in ok to pump mode.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 99 of 115
There will be a light activated above the pump panel light switch when the parking brake is set. This is to afford the operator some illumination when first approaching the control panel.

AIR HORN SYSTEM
Two (2) Hadley®, eTone, chrome air horns will be recessed in the front bumper. The air horn system will be piped to the air brake system wet tank utilizing 0.38" tubing. A pressure protection valve will be installed to prevent the loss of air in the brake system.

Air Horn Location
The air horns will be located on the left side of the bumper, outside of the frame rail.

Air Horn Control
The air horn(s) will be activated by the following:
• Right side chrome push button switch
• Steering wheel horn ring with electric/air horn selector switch • Left side foot switch

AIR HORN SWITCHING
The air horns will be the default from the horn ring when the battery switch is turned on. The electric chassis horns will be secondary.

ELECTRONIC SIREN
A Whelen, Model 295HFS2, electronic remote siren with noise canceling microphone will be provided.

This siren to be active when the battery switch is on and that emergency master switch is on.

Electronic siren head will be recessed in the passenger side center switch panel.

SIREN CONTROL
The electronic siren will be controllable on the siren head and horn ring only. No foot switches will be required.

The driver will have the option to control the siren or the chassis horns from the horn button by means of a selector switch located on the instrument panel.

SPEAKER
There will be one (1) Whelen®, Model SA315P, black nylon composite, 100-watt, speaker with through bumper mounting brackets and polished stainless steel grille provided. The speaker will be connected to the siren amplifier.

The speaker will be recessed in the right side of the front bumper, inside of the frame rail.

AUXILIARY MECHANICAL SIREN
There will be a Federal Signal Model Q2B mechanical siren furnished and installed in the front of the apparatus.

The Q2B siren will be chrome finish.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 100 of 115
The siren will have a 2-gauge cable connected to a Littelfuse part number 24213 power solenoid that is connected by a 2-gauge cable ran battery direct to the primary chassis batteries and will be labeled Q2B+ at the battery. The power solenoid will only be enabled when the emergency master switch is on.

The siren will have a 2-gauge ground wire connected to the chassis battery stud. The cable will be labeled Q2B- at the battery.

The mechanical siren will be recessed in the front bumper on the right side. The siren will be properly supported using the bumper framework.

MECHANICAL SIREN CONTROL
The mechanical siren will be activated by the following:
• Right side push button switch.
• Left side foot switch.

A momentary red switch will be included in the left side overhead switch panel to activate the siren brake.

A momentary chrome push button switch will be included in the right side dash panel to activate the siren brake.

FRONT ZONE UPPER WARNING LIGHTS
There will be one (1) 81.00" Whelen® Freedom™ IV LED lightbar mounted on the cab roof.

The lightbar will include the following:
• One (1) red flashing LED module in the driver's side end position. • One (1) red flashing LED module in the driver's side front corner position. • One (1) red flashing LED module in the driver's side first front position. • One (1) red flashing LED module in the driver's side second front position. • One (1) white flashing LED module in the driver's side third front position. • One (1) red flashing LED module in the driver's side fourth front position. • One (1) red flashing LED module in the driver's side fifth front position. • Open in the driver's side sixth front position.
• One (1) 795 LED traffic light controller set to national standard high priority in the center positions.
• Open in the passenger's side sixth front position.
• One (1) red flashing LED module in the passenger's side fifth front position. • One (1) red flashing LED module in the passenger's side fourth front position. • One (1) white flashing LED module in the passenger's side third front position. • One (1) red flashing LED module in the passenger's side second front position. • One (1) red flashing LED module in the passenger's side first front position.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 101 of 115
• One (1) red flashing LED module in the passenger's side front corner position. • One (1) red flashing LED module in the passenger's side end position.

There will be clear lenses included on the lightbar.

The following switches may be a installed in the cab on the switch panel to control the lightbar:
• a switch to control the flashing LED modules.
• the traffic light controller by a cab switch with emergency master control. • no momentary switch to activate the traffic light controller.

The white flashing LED modules and the traffic light controller will be disabled when the parking brake is applied.

The eight (8) red flashing LED modules in the front positions may be load managed when the parking brake is applied.

FRONT ZONE LOWER LIGHTS
There will be four (4) Whelen®, 4.31" high x 6.75" wide x 1.37" deep lights installed on the cab face above the headlights, in a common bezel matching the one for the headlamps per the following. • One (1) Model M6** flashing light installed in the left side outside position. The left side outside warning light to include red LEDs.
• One (1) Model M6RS steady burning light installed in the left side inside position. The light will include red LEDs.
• One (1) Model M6RS steady burning light installed in the right side inside position. The light will include red LEDs.
• One (1) Model M6** flashing light installed in the right side outside position. The right side outside warning light to include red LEDs.
• The lens color(s) to be the same as the LEDs.
• The housing to be polished and the trim shall be chrome.

There will be a switch in the cab on the switch panel to control the lights.

DAYTIME RUNNING LIGHTS (HEADLIGHTS)
The low-beam headlights used as daytime running lights will be activated with the following measures:
• Ignition switch is turned on
• Parking brake is released
These lights will be deactivated with any one of the following measures:
• Headlight switch is turned on
• High-beam flash is turned on
• Parking brake is set

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 102 of 115

HEADLIGHT FLASHER
The high beam headlights will flash alternately between the left and right side.

There will be a switch installed in the cab on the switch panel to control the high beam flash. This switch will be live when the battery switch and the emergency master switches are on.

The flashing will automatically cancel when the headlight (high or low beam) switch is activated or when the parking brake is set.

SIDE ZONE LOWER FRONT WARNING
There will be two (2) Whelen®, Model M6#, 4.31" high x 6.75" long x 1.37" deep flashing split color LED warning lights with chrome trim installed per the following:
• There will be one (1) each side on the front custom cab corner in a polished stainless steel bracket.
• The left side front light to include red LEDs to the front with white LEDs to the rear. • The right side front light to include red LEDs to the front with white LEDs to the rear. • The lens color will be clear.

The lights will be activated with a switch in the cab on the switch panel.

SIDE ZONE LOWER MIDDLE WARNING
There will be two (2) Whelen®, Model M6**, 4.31" high x 6.75" long x 1.37" deep flashing LED warning lights with chrome trim installed per the following:
• There will be one (1) each side of cab rearward of crew cab doors. • The left side, side middle light to include red warning LEDs. • The right side, side middle light to include red warning LEDs. • The warning light lens colors to be the same as the LEDs.

The lights will be activated with a switch in the cab on the switch panel.

SIDE ZONE LOWER REAR WARNING
There will be two (2) Whelen®, Model M6**, 4.31" high x 6.75" long x 1.37" deep flashing LED warning lights with chrome trim installed per the following:
• There will be one (1) each side on the rear fender panel. • The left side, side rear light to include red warning LEDs. • The right side, side rear light to include red warning LEDs. • The warning light lens colors to be the same as the LEDs .

The lights will be activated with a switch in the cab on the switch panel.

REAR ZONE LOWER LIGHTING
There will be two (2) Whelen®, Model M6*, LED flashing warning lights will be located at the rear of the apparatus.
• The driver's side rear light to be red
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 103 of 115
• The passenger's side rear light to be red
Both lights will include a lens that is the same color as the LED's.

There will be a switch located in the cab on the switch panel to control the lights.

REAR/SIDE ZONE UPPER WARNING LIGHTS
There will be two (2) Whelen®, Model L31H*FN, LED warning beacons provided at the rear of the truck, located one (1) each side. There will be a switch located in the cab on the switch panel to control the beacons.

The color of the lights will be red LEDs with both domes red.

The rear warning lights will be mounted on polished stainless steel brackets with all wiring totally enclosed. These brackets will also support clearance/marker lights. The rear deck lights will be mounted on the beavertail flange to keep the overall height as low as possible.

TRAFFIC DIRECTING LIGHT
There will be one (1) Whelen® Model TAM65, 36.00" long x 2.87" high x 2.25" deep, amber LED traffic directing light installed at the rear of the apparatus.

The Whelen Model TACTL5 control head will be included with this installation.

The control head will be energized when the battery switch is on.

The auxiliary flash to be activated when the emergency master switch is on.

This traffic directing light will be recessed with a stainless steel trim plate at the rear of the apparatus as high as practical.

The traffic directing light control head will be located in the driver side overhead switch panel in the center panel position.
120 VOLT RECEPTACLE
There will be one (1), 15/20 amp 120 volt AC three (3) wire straight blade duplex receptacle(s) with interior stainless steel wall plate(s), installed located in RS1 on the tank wall low towards the floor in the front corner. . The NEMA configuration for the receptacle(s) will be 5-20R.

The receptacle(s) will be powered from the shoreline inlet.

There will be a label installed near the receptacle(s) that state the following:
• Line Voltage
• Current Ratting (amps)
• Phase
• Frequency

LOOSE EQUIPMENT
The following equipment will be furnished with the completed unit:

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 104 of 115
• One (1) bag of chrome, stainless steel, or cadmium plated screws, nuts, bolts and washers, as used in the construction of the unit.

NFPA LOOSE EQUIPMENT
NFPA Required Loose Equipment Provided by Fire Department The following loose equipment as outlined in NFPA 1900, 2024 edition, table 8.1 will be provided by the fire department:
• One (1) traffic vest for each seating position, each vest to comply with ANSI/ISEA 207, Standard for High Visibility Public Safety Vests, and have a five-point breakaway feature that includes two (2) at the shoulders, two (2) at the sides, and one (1) at the front. • Five (5) fluorescent orange traffic cones not less than 28.00" (711 mm) in height, each equipped with a 6.00" (152 mm) retro-reflective white band no more than 4.00" (152 mm) from the top of the cone, and an additional 4.00" (102 mm) retro-reflective white band 2.00" (51 mm) below the

6.00" (152 mm) band.
• Five (5) illuminated warning devices such as highway flares, unless the five (5) fluorescent orange traffic cones have illuminating capabilities.

NFPA Loose Equipment That Shall be Considered:

The following loose equipment as outlined in NFPA 1900, 2024 edition, appendix table A.8.4 (a) should be considered:
• 800 ft (60 m) of 2.50" (65 mm) or larger fire hose.
• 400 ft (120 m) of 1.50" (38 mm), 1.75" (45 mm), or 2.00" (52 mm) fire hose. • One (1) handline nozzle, 200 gpm (750 L/min) minimum. • Two (2) handline nozzles, 95 gpm (360 L/min) minimum. • One (1) smooth bore or combination nozzle with shutoff and with 2.50" (65 mm) inlet that flows a minimum of 250 gpm (950 L/min).
• Four (4) SCBA apparatus
• Four (4) SCBA spare cylinders
• One (1) first aid kit.
• Four (4) combination spanner wrenches.
• Two (2) hydrant wrenches.
• One (1) double female 2.50" (65 mm) adapter with national hose (NH) threads. • One (1) double male 2.50" (65 mm) adapter with national hose (NH) threads. • One (1) rubber mallet, for use on suction hose connections. • Two (2) salvage covers each a minimum size of 12 ft × 18 ft (3.7 m × 5.5 m). • One (1) automatic external defibrillator (AED).

SOFT SUCTION HOSE PROVIDED BY FIRE DEPARTMENT
Hose is not on the apparatus as manufactured. The fire department will provide suction or supply hose. - One (1)-4.50" National Standard hose thread barrel strainer, chrome plated DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 105 of 115

DRY CHEMICAL EXTINGUISHER PROVIDED BY FIRE DEPARTMENT
The extinguisher is not on the apparatus as manufactured. The fire department will provide and mount the extinguisher.

WATER EXTINGUISHER PROVIDED BY FIRE DEPARTMENT
The extinguisher is not on the apparatus as manufactured. The fire department will provide and mount the extinguisher.

FLATHEAD AXE PROVIDED BY FIRE DEPARTMENT
The axe is not on the apparatus as manufactured. The fire department will provide and mount the axe.

PICKHEAD AXE PROVIDED BY FIRE DEPARTMENT
The axe is not on the apparatus as manufactured. The fire department will provide and mount the axe.

PAINT PROCESS
The exterior custom cab and body painting procedure will consist of a seven (7) step finishing process as follows:

1. Manual Surface Preparation - All exposed metal surfaces on the custom cab and body will be thoroughly cleaned and prepared for painting. Imperfections on the exterior surfaces will be removed and sanded to a smooth finish. Exterior seams will be sealed before painting. Exterior surfaces that will not be painted include; chrome plating, polished stainless steel, anodized aluminum and bright aluminum treadplate.

2. Chemical Cleaning and Pretreatment - All surfaces will be chemically cleaned to remove dirt, oil, grease, and metal oxides to ensure the subsequent coatings bond well. The aluminum surfaces will be properly cleaned and treated using a high pressure, high temperature 4 step Acid Etch process. The steel and stainless surfaces will be properly cleaned and treated using a high temperature 3 step process specifically designed for steel or stainless. The chemical treatment converts the metal surface to a passive condition to help prevent corrosion.

3. Surfacer Primer - The Surfacer Primer will be applied to a chemically treated metal surface to provide a strong corrosion protective basecoat. A minimum thickness of 2 mils of Surfacer Primer is applied to surfaces that require a Critical aesthetic finish. The Surfacer Primer is a two-component high solids urethane that has excellent sanding properties and an extra smooth finish when sanded.

4. Finish Sanding - The Surfacer Primer will be sanded with a fine grit abrasive to achieve an ultrasmooth finish. This sanding process is critical to produce the smooth mirror like finish in the topcoat.

5. Sealer Primer - The Sealer Primer is applied prior to the Basecoat in all areas that have not been previously primed with the Surfacer Primer. The Sealer Primer is a two-component high solids urethane that goes on smooth and provides excellent gloss hold out when topcoated.

6. Basecoat Paint - Two coats of a high performance, two component high solids polyurethane basecoat will be applied. The Basecoat will be applied to a thickness that will achieve the proper color match. The Basecoat will be used in conjunction with a urethane clear coat to provide protection from the environment.

7. Clear Coat - Two (2) coats of Clear Coat will be applied over the Basecoat color. The Clear Coat is a two-component high solids urethane that provides superior gloss and durability to the DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 106 of 115
exterior surfaces. Lap style and roll-up doors will be Clear Coated to match the body. Paint warranty for the roll-up doors will be provided by the roll-up door manufacturer.

After the cab and body are painted, the color will be verified to make sure that it matches the color standard. Electronic color measuring equipment will be used to compare the color sample to the color standard entered into the computer. Color specifications will be used to determine the color match. A Delta E reading will be used to determine a good color match within each family color.

All removable items such as brackets, compartment doors, door hinges, and trim will be removed and painted separately if required, to ensure paint behind all mounted items. Body assemblies that cannot be finish painted after assembly will be finish painted before assembly.

The paint finish quality levels for critical areas of the apparatus (cab front and sides, body sides and doors, and boom lettering panels) are to meet or exceed Cadillac/General Motors GMW15777 global paint requirements. Orange peel levels are to meet or exceed the #6 A.C.T. standard in critical areas.

The manufacture's written paint standards will be available upon request.

Environmental Impact
Contractor will meet or exceed all current state regulations concerning paint operations. Pollution control will include measures to protect the atmosphere, water and soil. Controls will include the following conditions:
• Topcoats and primers will be chrome and lead free.
• Metal treatment chemicals will be chrome free. The wastewater generated in the metal treatment process will be treated on-site to remove any other heavy metals. • Particulate emission collection from sanding operations will have a 99.99 percent efficiency factor.
• Particulate emissions from painting operations will be collected by a dry filter or water wash process. If the dry filter is used, it will have an efficiency rating of 98 percent. Water wash systems will be 99.97 percent efficient
• Water from water wash booths will be reused. Solids will be removed on a continual basis to keep the water clean.
• Paint wastes are disposed of in an environmentally safe manner. • Empty metal paint containers will be recycled to recover the metal. • Solvents used in clean-up operations will be recycled on-site or sent off-site for distillation and returned for reuse.

Additionally, the finished apparatus will not be manufactured with or contain products that have ozone depleting substances. Contractor will, upon demand, present evidence that the manufacturing facility meets the above conditions and that it is in compliance with his state EPA rules and regulations.

TWO-TONE CAB PAINT
The cab will be painted two-tone with the upper section painted #10 white and the lower section painted #80 red. There will be a standard two-tone cab paint break provided.

There will be a standard cab shield provided.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 107 of 115

BODY PAINT
The body will be painted to match the lower section of the cab.

PAINT CHASSIS FRAME ASSEMBLY
The chassis frame assembly will be finished with a single system black top coat before the installation of the cab and body, and before installation of the engine and transmission assembly, air brake lines, electrical wire harnesses, etc.

Components that are included with the chassis frame assembly that will be painted are:
• Frame rails
• Frame liners
• Cross members
• Axles
• Suspensions
• Steering gear
• Battery boxes
• Bumper extension weldment
• Frame extensions
• Body mounting angles
• Rear Body support substructure (front and rear)
• Pump house substructure
• Steel fuel tank
• Castings
• Individual piece parts used in chassis and body assembly Components treated with epoxy E-coat protection prior to paint:
• Two (2) C-channel frame rails
• Two (2) frame liners
The E-coat process will meet the technical properties shown.

AXLE HUB PAINT
All axle hubs will be painted black #101.

COMPARTMENT INTERIOR PAINT
The interior of all compartments will be painted with a gray spatter finish for ease of cleaning and to make it easier to touch up scratches and nicks.

REFLECTIVE BAND
A 6.00" white reflective band will be provided across the front of the vehicle and along the sides of the body.

The reflective band provided on the cab face will be at the headlight level.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 108 of 115

CHEVRON STRIPING, REAR
There will be alternating chevron striping located on the rear-facing vertical surface of the apparatus.

The rear surface, excluding the rear bulkhead and rear compartment door, will be covered.

The colors will be red and fluorescent yellow green diamond grade.

Each stripe will be 6.00" in width.

This will meet the requirements of NFPA 1901, 2009 edition, which states that 50% of the rear surface will be covered with chevron striping.

CHEVRON STRIPING ON REAR ROLLUP COMPARTMENT
There will be alternating chevron striping located on the rear rollup door.

The colors will be red and fluorescent yellow green diamond grade.

Each stripe will be 6.00" in width.

CAB DOOR REFLECTIVE STRIPE
A 6.00" x 16.00" white reflective stripe will be provided across the interior of each cab door. The stripe will be located approximately 1.00" up from the bottom, on the door panel.

This stripe will meet the NFPA 1901 requirement.

CAB STRIPE
There will be a genuine gold leaf stripe provided on both sides of the cab in place of the chrome molding.

CAB STRIPE
There will be a genuine gold leaf stripe on each side of the cab, low and over the fender.

CAB FACE STRIPE
There will be a genuine gold leaf striped corner on each front corner of the cab.

LETTERING
The lettering will be totally encapsulated between two (2) layers of clear vinyl.

LETTERING
Twenty-one (21) to forty (40) genuine gold leaf lettering, 3.00" high, with outline and shade will be provided.

BODY STRIPE
There will be a genuine gold leaf stripe provided on each side of the body, located along the top of the side compartmentation.

BODY STRIPE
There will be a genuine gold leaf stripe provided on each side of the body, low and over the fender along the bottom of the compartment doors.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 109 of 115

LETTERING
There will be non-reflective vinyl lettering, 2.00" high, with no outline or shade provided. There will be six (6) letters provided.

LETTERING
There will be non-reflective vinyl lettering, 18.00" high, with no outline or shade provided. There will be three (3) letters provided.

LETTERING
There will be non-reflective vinyl lettering, 7.00" high, with outline and shade provided. There will be three (3) letters provided.

LETTERING
There will be non-reflective vinyl lettering, 10.00" high, with outline and shade provided. There will be three (3) letters provided.

LETTERING
There will be genuine gold leaf lettering, 2.00" high, with outline and shade provided. There will be nine (9) letters provided.

LETTERING
There will be non-reflective vinyl lettering, 14.00" high, with no outline or shade provided. There will be three (3) letters provided.

LETTERING
Sixty-one (61) to eighty (80) genuine gold leaf lettering, 2.00" high, with outline and shade will be provided.

LETTERING
There will be genuine gold leaf lettering, 4.00" high, with outline and shade provided. There will be ten (10) letters provided.

REFLECTIVE LETTERING
18 letters, 5.00" high will be cut into the reflective stripe to allow the painted surface to form the letter.

The letters will be "PARAMEDIC" on the D1 and P1 compartment doors per LSP.

MALTESE CROSS INSTALLATION
There will be one (1) pair of maltese crosses, comprised of genuine gold leaf material, provided and installed cab doors..

LETTERING/NUMERAL ON CAB GRILLE
One (1) painted letter/numeral, as determined by the fire department, will be provided on the cab grille.

MANUAL, FIRE APPARATUS PARTS
Two (2) custom parts manuals for the complete fire apparatus will be provided in hard copy with the completed unit.

The manual will contain the following:

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 110 of 115
- Job number
- Part numbers with full descriptions
- Table of contents
- Parts section sorted in functional groups reflecting a major system, component, or assembly - Parts section sorted in Alphabetical order
- Instructions on how to locate a part
The manual will be specifically written for the chassis and body model being purchased. It will not be a generic manual for a multitude of different chassis and bodies.

SERVICE PARTS INTERNET SITE
The service parts information included in this manual is also available on the Pierce website. The website offers additional functions and features not contained in this manual, such as digital photographs and line drawings of select items. The website also features electronic search tools to assist in locating parts quickly.

MANUALS, CHASSIS SERVICE
Two (2) chassis service manuals containing parts and service information on major components will be provided with the completed unit.

The manuals will contain the following sections:
- Job number
- Table of contents
- Troubleshooting
- Front Axle/Suspension
- Brakes
- Engine
- Tires
- Wheels
- Cab
- Electrical, DC
- Air Systems
- Plumbing
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 111 of 115
- Appendix
The manual will be specifically written for the chassis model being purchased. It will not be a generic manual for a multitude of different chassis and bodies.

MANUALS, CHASSIS OPERATION
Two (2) chassis operation manuals will be provided.

ONE (1) YEAR MATERIAL AND WORKMANSHIP
A Pierce basic apparatus limited warranty certificate, WA0008, is included with this proposal.

ENGINE WARRANTY
A Cummins five (5) year limited engine warranty will be provided. A limited warranty certificate, WA0181, is included with this proposal.

STEERING GEAR WARRANTY
A Sheppard three (3) year limited steering gear warranty will be provided. A copy of the warranty certificate will be submitted with this proposal.

FIFTY (50) YEAR STRUCTURAL INTEGRITY
The Pierce custom chassis frame limited warranty certificate, WA0013, is included with this proposal.

FRONT AXLE THREE (3) YEAR MATERIAL AND WORKMANSHIP WARRANTY The Pierce TAK-4 suspension limited warranty certificate, WA0050, is included with this proposal.

SINGLE REAR AXLE FIVE (5) YEAR MATERIAL AND WORKMANSHIP WARRANTY A Meritor™ Axle 5 year limited warranty will be provided.

ABS BRAKE SYSTEM THREE (3) YEAR MATERIAL AND WORKMANSHIP WARRANTY A Meritor Wabco™ ABS brake system limited warranty certificate, WA0232, is included with this proposal.

TEN (10) YEAR STRUCTURAL INTEGRITY
The Pierce custom cab limited warranty certificate, WA0012, is included with this proposal.

TEN (10) YEAR PRO-RATED PAINT AND CORROSION
A Pierce cab limited pro-rated paint warranty certificate, WA0055, is included with this proposal.

FIVE (5) YEAR MATERIAL AND WORKMANSHIP
The Pierce Command Zone electronics limited warranty certificate, WA0014, is included with this proposal.

CAMERA SYSTEM WARRANTY
A Pierce fifty four (54) month warranty will be provided for the camera system.

COMPARTMENT LIGHT WARRANTY
The compartment lights will not offer an extended warranty.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 112 of 115

TRANSMISSION WARRANTY
The transmission will have a five (5) year/unlimited mileage warranty covering 100 percent parts and labor. The warranty will be provided by Allison Transmission.

Note: The transmission cooler is not covered under any extended warranty you may be getting on your Allison Transmission. Please review your Allison Transmission warranty for coverage limitations.

TRANSMISSION COOLER WARRANTY
The transmission cooler will carry a five (5) year parts and labor warranty (exclusive to the transmission cooler). In addition, a collateral damage warranty will also be in effect for the first three (3) years of the warranty coverage and will not exceed $10,000 per occurrence. A copy of the warranty certificate will be included with this proposal.

WATER TANK WARRANTY
A UPF poly water tank limited warranty certificate, WA0195, is included with this proposal.

TEN (10) YEAR STRUCTURAL INTEGRITY
The Pierce apparatus body limited warranty certificate, WA0009, is included with this proposal.

ROLL UP DOOR MATERIAL AND WORKMANSHIP WARRANTY
A Gortite roll-up door limited warranty will be provided. The mechanical components of the roll-up door will be warranted against defects in material and workmanship for the lifetime of the vehicle. A six (6) year limited warranty will be provided on painted and satin roll up doors.

The limited warranty certificate, WA0190, is included with this proposal.

PUMP WARRANTY
The Waterous pump will be provided with a seven (7) year material and workmanship limited warranty.

A copy of the warranty certificate will be included with this proposal.

TEN (10) YEAR PUMP PLUMBING WARRANTY
The Pierce apparatus plumbing limited warranty certificate, WA0035, is included with this proposal.

FOAM SYSTEM WARRANTY
The Husky 3 foam system limited warranty certificate, WA0231, is included with this proposal.

TEN (10) YEAR PRO-RATED PAINT AND CORROSION
A Pierce body limited pro-rated paint warranty certificate, WA0057, is included with this proposal.

THREE (3) YEAR MATERIAL AND WORKMANSHIP
The Pierce Goldstar gold leaf lamination limited warranty limited warranty certificate, WA0018, is included with this proposal.

VEHICLE STABILITY CERTIFICATION
The fire apparatus manufacturer will provide a certification stating the apparatus complies with NFPA 1900, current edition, section 7.14, Vehicle Stability. The certification is included with this proposal.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 113 of 115

ENGINE INSTALLATION CERTIFICATION
The fire apparatus manufacturer will provide a certification, along with a letter from the engine manufacturer stating they approve of the engine installation in the bidder's chassis. The certification will be provided at the time of delivery.

POWER STEERING CERTIFICATION
The fire apparatus manufacturer will provide a certification stating the power steering system as installed meets the requirements of the component supplier. The certification is included with this proposal.

CAB INTEGRITY CERTIFICATION
The fire apparatus manufacturer will provide a cab crash test certification with this proposal. The certification will state that a specimen representing the substantial structural configuration of the cab has been tested and certified by an independent third party test facility. Testing events will be documented with photographs, real-time and high-speed video, vehicle accelerometers, cart accelerometers, and a laser speed trap. The fire apparatus manufacturer will provide a state licensed professional engineer to witness and certify all testing events. Testing will meet or exceed the requirements below:
• SAE J2422 Cab Roof Strength Evaluation - Quasi-Static Loading Heavy Trucks. • European Occupant Protection Standard ECE Regulation No.29. • SAE J2420 COE Frontal Strength Evaluation - Dynamic Loading Heavy Trucks.

Side Impact
The cab will be subjected to dynamic preload where a 14,320-lb moving barrier is slammed into the side of the cab at 5.50 mph, striking with an impact of 13,000 ft-lb of force. This test is part of the SAE J2422 test procedure and more closely represents the forces a cab will see in a rollover incident.

Frontal Impact
The same cab will withstand a frontal impact of 32,600 ft-lb of force using a moving barrier in accordance with SAE J2420.

Additional Frontal Impact
The same cab will withstand a frontal impact of 65,098 ft-lb of force using a moving barrier. (Twice the force required by SAE J2420)
Roof Crush
The cab will be subjected to a roof crush force of 22,500 lb. This value meets the ECE 29 criteria, and is equivalent to the front axle rating up to a maximum of ten (10) metric tons.

Additional Roof Crush
The same cab will be subjected to a roof crush force of 110,000 lbs. (Four and a half times the load criteria of ECE 29)
The same cab will withstand all tests without any measurable intrusion into the survival space of the occupant area.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 114 of 115
There will be no exception to any portion of the cab integrity certification. Nonconformance will lead to immediate rejection of bid.

CAB DOOR DURABILITY CERTIFICATION
Robust cab doors help protect occupants. Cab doors will survive a 200,000 cycle door slam test where the slamming force exceeds 20 G's of deceleration. The bidder will certify that the sample doors similar to those provided on the apparatus have been tested and have met these criteria without structural damage, latch malfunction, or significant component wear.

WINDSHIELD WIPER DURABILITY CERTIFICATION
Visibility during inclement weather is essential to safe apparatus performance. Windshield wipers will survive a 3 million cycle durability test in accordance with section 6.2 of SAE J198 Windshield Wiper Systems - Trucks, Buses and Multipurpose Vehicles. The bidder will certify that the wiper system design has been tested and that the wiper system has met these criteria.

ELECTRIC WINDOW DURABILITY CERTIFICATION
Cab window roll-up systems can cause maintenance problems if not designed for long service life. The window regulator design will complete 30,000 complete up-down cycles and still function normally when finished. The bidder will certify that sample doors and windows similar to those provided on the apparatus have been tested and have met these criteria without malfunction or significant component wear.

SEAT BELT ANCHOR STRENGTH
Seat belt attachment strength is regulated by Federal Motor Vehicle Safety Standards and should be validated through testing. Each seat belt anchor design will withstand 3000 lb of pull on both the lap and shoulder belt in accordance with FMVSS 571.210 Seat Belt Assembly Anchorages. The bidder will certify that each anchor design was pull tested to the required force and met the appropriate criteria.

SEAT MOUNTING STRENGTH
Seat attachment strength is regulated by Federal Motor Vehicle Safety Standards and should be validated through testing. Each seat mounting design will be tested to withstand 20 G's of force in accordance with FMVSS 571.207 Seating Systems. The bidder will certify, at time of delivery, that each seat mount and cab structure design was pull tested to the required force and met the appropriate criteria.

PERFORMANCE CERTIFICATIONS
Cab Air Conditioning
Good cab air conditioning temperature and air flow performance keeps occupants comfortable, reduces humidity, and provides a climate for recuperation while at the scene. The cab air conditioning system will cool the cab from a heat-soaked condition at 100 degrees Fahrenheit to an average of 78 degrees Fahrenheit in 30 minutes. The bidder will certify that a substantially similar cab has been tested and has met these criteria.

Cab Defroster
Visibility during inclement weather is essential to safe apparatus performance. The defroster system will clear the required windshield zones in accordance with SAE J381 Windshield Defrosting Systems DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 City of Emeryville
Two (2) Pierce Manufacturing, Inc. Enforcer 1500 GPM Type 1 Engines 115 of 115
Test Procedure And Performance Requirements - Trucks, Buses, And Multipurpose Vehicles. The bidder will certify that the defrost system design has been tested in a cold chamber and passes the SAE J381 criteria.

Cab Auxiliary Heater
Good cab heat performance and regulation provides a more effective working environment for personnel, whether in-transit, or at a scene. An auxiliary cab heater will warm the cab 77 degrees Fahrenheit from a cold-soak, within 30 minutes when tested using the coolant supply methods found in SAE J381. The bidder will certify, at time of delivery, that a substantially similar cab has been tested and has met these criteria.

AMP DRAW REPORT
The bidder will provide, at the time of bid and delivery, an itemized print out of the expected amp draw of the entire vehicle's electrical system.

The manufacturer of the apparatus will provide the following:
• Documentation of the electrical system performance tests. • A written load analysis, which will include the following:
o The nameplate rating of the alternator.
o The alternator rating under the conditions specified per:
 Current edition of applicable NFPA standards.
o The minimum continuous load of each component that is specified per:
 Current edition of applicable NFPA standards.
o Additional loads that, when added to the minimum continuous load, determine the total connected load.
o Each individual intermittent load.

All of the above listed items will be provided by the bidder per the current edition of applicable NFPA standards.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 Option Description Type* Minimum
Load
Intermittent
Load
Total
Connected
0001244 High Idle w/Electronic Engine, Custom 0.00 1.20 0.00 0002526 Light, Engine Compt, All Custom Chassis 0.00 1.60 0.00 0005945 Light, Pump Compt 0.00 1.80 0.00
0072153 Primer, Trident, Air Prime, Air Operated 0.00 0.00 0.00 0079211 Batteries, (6) Stryten/Exide Grp 31, 950 CCA each, Threaded Stud 0.00 3.00 0.00 0549333 Indicators, Engine, Included with Pressure Controller 0.00 0.35 0.00 0589905 Alarm, Back-up Warning, PRECO 1040 0.00 0.50 0.00 0622582 Cab Lift, Elec/Hyd, Manual Override, Control Loc Feature, Sab FR/Enf

0.00 180.00 0.00
0624939 Foam Sys, Husky 3, Single Agent, Multi Select Feature 0.00 55.00 0.00 0630636 Controls, Electric Roll-Up Windows, 4dr, 4 Driver Controls, Saber FR/Enforcer

0.00 26.00 0.00
0644461 Wiring, Spare, 40 A 12V DC, 20A Bat, 20A Sw Bat, Grnd 0.00 0.00 40.00 0652818 Speaker, Motorola, Model #HSN4040, Each 0.00 0.00 0.00 0683542 Reel, Booster, Aluminum - Over Pump, Right Side, NPSH Fittings 0.00 36.00 0.00 0687994 Engine Brake, Jacobs Compression Brake, Cummins Engine 0.00 0.42 0.00 0734904 Wiring, Spare, 20 A 12V DC, 5A EM, 5A Prk Brk, 5A Right Dir, 5A Left Dir, Gnd

0.00 0.00 20.00
0735006 Intercom, David Clark, 4-Pos, 2-Radio, (D, O, RPTT), 2obC, U3805

0.00 0.00 0.50
0743527 Light, Roof Mt, HiViz, FT-B-72-ML-*, Cnt Feature MUX 0.00 0.00 21.70 0768541 Light, Hose Bed, Amdor AY-LB-12HW040, 40" LED 0.00 0.00 0.60 0774308 Lights, Wln, P*H2* Pioneer, 12 VDC, 2nd 0.00 0.00 13.00 0774309 Lights, Wln, P*H2* Pioneer, 12 VDC, 1st 0.00 0.00 13.00 0806466 Lights, Backup, Wln M62BU, LED, For Tail Lt Housing 0.00 3.20 0.00 0816158 Camera, Pierce, LS Mux, RS, LS, R, Cameras, AHD 0.00 1.20 0.00 0819040 Light, Do Not Move Apparatus, Wln VTX609B, MPI-47B Piezo, PB Non-NFPA 2024

0.00 2.80 0.00
0819994 Radio, Jensen, AM/FM/WB, Bluetooth 0.00 0.00 2.00 0820509 ESC/ABS/ATC Wabco Brake System, Single Rear Axle, NFPA 1900

0.00 6.00 0.00
0821192 Wiring, Spare, 20 A 12V DC 1st NFPA1900 0.00 0.00 20.00 0821452 Wiring, Spare, 40 A 12V DC 1st NFPA1900 0.00 0.00 80.00 0821470 Wiring, Spare, 4.8 A 12V DC, USB Termination 1st NFPA1900 0.00 0.00 9.60 0821473 Wiring, Spare, 4.8 A 12V DC, USB Term Batt Dir 1st NFPA1900 0.00 0.00 9.60 0892635 Light, P25 LED Hooded Light, PP Lt Sw 0.00 0.00 0.50 0895281 Siren, Federal Q2B, Littelfuse 24213 Sol 0.00 100.00 0.00 0032189 Mirrors, Ramco, 8000PCHR, Heated/Remote, w/Heated/Remote Convex, Door Mount
Load Managed 0.00 0.00 8.00
0696870 Lights, Side Scene, TecNiq, E960 LED, Stainless 1st Pr Load Managed 0.00 0.00 1.20 0722696 HVAC, Standard-Duty, Enforcer, CARE Load Managed 0.00 0.00 100.00 0820906 Wiring, Spare, 15 A 12V DC 2nd NFPA1900 Load Managed 0.00 0.00 30.00 0821438 Wiring, Spare, 15 A 12VDC Power Point, Dual USB-C Batt Dir NFPA1900 1st
Load Managed 0.00 0.00 15.00
0002758 Amp Draw, NFPA/ULC Radio Allowance NFPA 5.00 0.00 0.00 0013671 Compt, Rear, Rollup, 30.75" FF, 25.88" D NFPA 0.90 0.00 0.90 0088745 Light, Rear Zone Up, Wln L31HRFN LED Beacon, Red LED NFPA 3.20 4.80 0.00 0092582 Load Manager/Sequencer, MUX NFPA 0.56 0.56 0.00 0536401 Gauges, Engine, Included With Pierce Pressure Controller NFPA 0.30 0.00 0.00 0536428 Gauge, Water Level, Pierce, In pressure Controller NFPA 1.23 0.00 0.00 0550598 Siren, Wln 295HFS2 Remote, Single Amp NFPA 1.40 12.60 0.00 0556360 Lights, Step, P25 LED 4lts, Pump Pnl Sw NFPA 1.00 0.00 0.00 0564654 Lights, Rear Zn Lwr, Wln M6*, Colored Lens, For Tail Light Housing
NFPA 1.80 2.70 0.00
0590517 LS 145" Rollup, Full Height Front & Rear, FDLER, 5" Longer than STD Short Body
NFPA 4.50 0.00 4.50
0593161 Light Shield, S/S LED NFPA 3.00 0.00 0.00
* UDMC = User Defined Mission Critical, LM = User Defined Load Managed, S = Electrical Amperage Supply 1 Electrical Analysis 5/7/2024
Bid #: 707
Alameda County Enforcer Pumper (City of Emeryville) Sales Rep:

Organization:

Martinez, Mike
Golden State Fire Apparatus, Inc
Desc:

Job #:

Customer: Alameda Co. FD
Option: Pierce Command Zone, Advanced Electronics & Control System, Enforcer, WiFi CZT
Type: Multiplexed
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 Option Description Type* Minimum
Load
Intermittent
Load
Total
Connected
0605126 Pump Shift, Air Mnl Override, Split Shaft, Interlocked, Waterous NFPA 1.00 0.00 0.00 0619421 Compt, Storage, Forward Facing, Overhead, 88 W x 10 H x 16.34 D, Saber FR/Enf
Load Managed 0.44 0.44 0.00
0620054 Light, Directional/Marker, Intermediate, Weldon 9186-8580-29 LED 2lts
NFPA 0.10 0.90 0.00
0622803 Cab Instruments, Black Gauges, Black Bezels, Enforcer MUX NFPA 1.26 0.00 0.00 0625953 Light, Directional, Wln 600 Cmb, Cab Crn, Wrp Bzl Out HD Lts, Enf, Sab FR
NFPA 0.70 0.70 0.00
0627282 Lights, Clearance/Marker/ID, Rear, FRP LED Bar & P25 LED 4Lts NFPA 1.75 0.00 0.00 0630489 Air Dryer, Bendix, AD-9, With Wet Tank, Heated, Saber FR/Enforcer
NFPA 7.81 0.00 0.00
0645667 Lights, Front of Hose Bed, Wln 60C0ELZR LED NFPA 2.00 0.00 0.00 0647647 Lights, Dome, FRP Dual LED 4 Lts NFPA 0.80 0.80 0.00 0647929 Lights, Directional/Marker, Cab Front Side, Truck-Lite 19036YLED,AXT/EnfMUX/DCF
NFPA 0.12 0.00 0.00
0648332 Cab, Enforcer, 7010 NFPA 6.80 10.20 0.00
0653937 Flasher, Headlight Alternating NFPA 0.08 0.00 0.00 0662965 DEF Tank, 4.5 Gallon, DS Fill, Rear of Axle, Common Air Bottle Door
NFPA 0.60 11.40 0.00
0672327 Lights, Deck, Wln (2) MPBW Micro Pioneer LED Rear Flood Lights NFPA 7.00 0.00 0.00 0709438 Lights, Walk Surf, FRP Flood, LED NFPA 2.00 0.00 0.00 0721609 Controller, Pressure, Pierce LCD, Custom Chassis NFPA 1.70 0.00 0.00 0734710 Lights, Clearance/Marker, Side, Truck-Lite 35200Y 2 Lts, Others With Visor Lt
NFPA 0.49 0.00 0.00
0736472 Cabinet, Rr Facing, RS, 22.75 W x 28 H x 23 D, Ext Acc Only, Sp Mtg, Lip,SFR/Enf
NFPA 0.28 0.28 0.00
0736474 Cabinet, Rr Facing, LS, 22.75 W x 28 H x 24 D, Ext Acc Only, Sp Mtg, Lip,SFR/Enf
NFPA 0.28 0.28 0.00
0739224 Indicator Light @ Pump Panel, Throttle Ready, Incl w/Pressure Gov/Throttle,Green
NFPA 0.10 0.00 0.00
0745568 Indicator Light, Pump Panel, Ok To Pump, Green NFPA 0.10 0.00 0.00 0769420 Lights, Perimeter Cab, Amdor AY-LB-12HW020 LED 4Dr NFPA 1.20 0.00 0.00 0769572 Lights, Perimeter Pump House, Amdor AY-LB-12HW020 LED 2lts NFPA 0.58 0.00 0.00 0770056 Lights, Perimeter Body, Amdor AY-LB-12HW020 LED 2lts, Rear Step
NFPA 0.60 0.00 0.00
0781245 RS 145" Rollup, Low, FDLER, 5" Longer than Standard Short NFPA 1.80 0.00 1.80 0783153 Headlights, Rect LED, JW Spkr Evo 2, AXT/DCF/Enf/Imp/Sab/Vel NFPA 4.20 4.20 0.00 0789486 Lightbar, Wln, Freedom IV-Q, 81", RRRRWRR_Opt_RRWRRRR NFPA 6.48 2.68 9.92 0791493 Light, Traffic Directing, Wln TAM65 36" Long LED NFPA 1.26 2.52 0.00 0804514 Lights, Tail, Wln M62BTT* Red Stop/Tail & M62T* Amber Dir Arw For Hsg
NFPA 0.83 2.49 0.00
0807112 Cabinet, Forward Facing, Center, 32 W x 50 H x 18 D, Roll, SFR/Enf
NFPA 0.50 0.50 0.00
0810947 Engine, Cummins X10, 450 hp, 1650 lb-ft, W/OBD, EPA 2027, Saber FR/Enforcer
NFPA 1.00 0.00 0.00
0813539 Cabinet, Rear Facing, RS, Overhead, 21 W x 10 H x 34 D, Drop Btm, SFR/Enf
NFPA 0.11 0.11 0.00
0814201 Vehicle Information Center, 7" Color Display, Touchscreen, MUX, CL714
NFPA 1.20 0.00 0.00
0816093 ClearSky Telematics, Remote Fleet & On-scene Management, AT&T Commercial
NFPA 1.61 0.00 0.00
0887546 Trans, Allison 6th Gen, 4000 EVS P, w/Prognostics, Imp/Vel/SFR/Enf
NFPA 2.00 2.00 0.00
0889577 Bracket, License Plate & Light, P25 LED, Stainless Brkt NFPA 0.07 0.00 0.00 0891663 Cabinet, Rear Facing, LS, Overhead, 21 W x 10 H x 34 D, Drop Btm, SFR/Enf
NFPA 0.11 0.11 0.00
0892638 Lights, Cab & Crw Cab Acs Stps, P25, LED w/Bezel, 6lts NFPA 1.00 0.00 0.00 0894096 Lights, Side Zone Lower Front, Wln M6# NFPA 0.88 1.32 0.00 0895777 Lights, Side Zone Lower Rear, Wln M6** NFPA 1.80 2.70 0.00 0895781 Lights, Side Zone Lower Middle, Wln M6* NFPA 1.80 2.70 0.00 0898690 Compt, Transverse Crew Cab, Dbl Pan, Rec Tube, 70" SFR/Enf NFPA 0.65 0.65 0.00 0899300 Lights, Front Zone, Wln M6** M6RS M6RS M6**, Inside Steady Burn, 4lts Q Bez
NFPA 3.60 5.40 0.00
0764491 Alternator, 420 amp, Leece-Neville BLP4003 S 0.00 0.00 0.00 Load Totals: 91.58 492.11 401.82
* UDMC = User Defined Mission Critical, LM = User Defined Load Managed, S = Electrical Amperage Supply 2 Electrical Analysis 5/7/2024
Bid #: 707
Alameda County Enforcer Pumper (City of Emeryville) Sales Rep:

Organization:

Martinez, Mike
Golden State Fire Apparatus, Inc
Desc:

Job #:

Customer: Alameda Co. FD
Option: Pierce Command Zone, Advanced Electronics & Control System, Enforcer, WiFi CZT
Type: Multiplexed
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 Minimum Continuous Load
Supply: 231.00
Demand: 91.58
Variance: 139.42
Total Connected Load
Supply: 342.00
Demand: 339.20
Variance: 2.80
Note: Minimum Continous Load is in "Blocking Right of Way" mode.(Reference current edition of NFPA 1901) Note: Intermittent Load items are not factored in on any alternator load comparisons. These items are included on the report for reference only and should be looked at as amp draw exclusion items. (Reference current edition of NFPA 1901) Note: Total Connected Load "Demand" represents Total Connected Load minus any Load Managed items Alternator Output at Idle: 231.00 Alternator Output at Governed Speed: 342.00 * UDMC = User Defined Mission Critical, LM = User Defined Load Managed, S = Electrical Amperage Supply 3 Electrical Analysis 5/7/2024
Bid #: 707
Alameda County Enforcer Pumper (City of Emeryville) Sales Rep:

Organization:

Martinez, Mike
Golden State Fire Apparatus, Inc
Desc:

Job #:

Customer: Alameda Co. FD
Option: Pierce Command Zone, Advanced Electronics & Control System, Enforcer, WiFi CZT
Type: Multiplexed
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 Turning Performance Analysis
Bid Number: 707 Chassis: Enforcer Chassis
Department: Alameda Co. FD Body: Pumper, Short, Galvanneal, 2nd Gen Parameters:
*Inside Cramp Angle: 45°
Axle Track: 82.92 in.

Wheel Offset: 4.68 in.

Tread Width: 15.9 in.

Chassis Overhang: 65.95 in.

Additional Bumper Depth: 10 in.

Front Overhang: 75.95 in.

Wheelbase: 182.5 in.

Calculated Turning Radii:

Inside Turn: 14 ft. 2 in.

Curb to curb: 27 ft. 11 in.

Wall to wall: 31 ft. 8 in.

Notes:
*Actual Inside cramp angle may be less than shown.

Curb to Curb turning radius calculated for 9.00 inch curb. 05/07/2024
Category Option Description
Bumpers 0606569 Bumper, 10" Extended, S/S, Saber FR/Enforcer Tires, Front 0802633 Tires, Front, Goodyear, Armor Max MSA, 385/65R22.50, 18 ply, Fire Ser. Load Rtg
Axle, Front, Custom 0630705 Axle, Front, Oshkosh TAK-4, Non Drive, 19,500 lb, Enforcer Wheels, Front 0019611 Wheels, Front, Alcoa, 22.50" x 12.25", Aluminum, Hub Pilot DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 Definitions:

Inside CrampAngle Maximum turning angle of the front inside fire.

Axle Track King-pin to King-pin distance of front axle.

Wheel Offset Offset from the center line of the wheel to the King-pin.

Tread Width Width of the tire tread.

Chassis Overhang Distance of the center line of the front axle to the front edge of the cab. This does not include the bumper depth.

Additional Bumper Wheel Depth that the bumper assembly adds to the front overhang.

Wheelbase Distance between the center lines of the vehicles front and rear axles.

Inside Turning Radius Radius of the smallest circle around which the vehicle can turn.

Curb to Curb Turning Radius Radius of the smallest circle around which the vehicle's tires can turn. This measures assumes a curb height of 9 inches.

Wall to Wall Turning Radius Radius of the smallest circle around which the vehicle's tires can turn. This measures takes into account any front overhang due to chassis , bumper extensions and or aerial devices.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 JROGHQVWDWHĆUHFRP

PRODUCT

WARRANTIES
Exhibit “C”
4 DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 2/8/2010 WA0008

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.

This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

No specific exclusions apply
Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4
Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

Fire and Rescue Apparatus
Coverage:

One (1) Year Material and Workmanship
Basic Apparatus
Twelve (12) months. Warranty Period
Ends After:

The date the apparatus is placed in service, or 60 days from the original buyer invoice date, whichever comes first. Warranty Begins:

Portions of the apparatus manufactured by Pierce shall be free from defects in material and workmanship
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.

Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.

3. BUYER'S EXCLUSIVE REMEDY.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 Cummins Warranty
Worldwide
Fire Apparatus/Crash Trucks
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 Coverage
Products Warranted
This Warranty applies to new diesel Engines sold by
Cummins and delivered to the first user on or after
April 1, 2007, that are used in fire apparatus truck and crash truck* applications Worldwide.

Base Engine Warranty
The Base Engine Warranty covers any failures of the
Engine which result, under normal use and service,
from a defect in material or factory workmanship
(Warrantable Failure). This Coverage begins with the
sale of the Engine by Cummins and ends five years or
100,000 miles (160,935 kilometers), whichever occurs
first, after the date of delivery of the Engine to the first user.

Engine aftertreatment components included in the
Cummins Critical Parts List (CPL) and marked with a
Cummins part number are covered under Base Engine
Warranty.

Additional Coverage is outlined in the Emission
Warranty section.

These Warranties are made to all Owners in the
chain of distribution and Coverage continues to all
subsequent Owners until the end of the periods of
Coverage.

Cummins
Responsibilities
Cummins will pay for all parts and labor needed to
repair the damage to the Engine resulting from a
Warrantable Failure.

Cummins will pay for the lubricating oil, antifreeze,
filter elements, belts, hoses and other maintenance
items that are not reusable due to the Warrantable
Failure.

Cummins will pay for reasonable labor costs for
Engine removal and reinstallation when necessary to
repair a Warrantable Failure.

Cummins will pay reasonable costs for towing a
vehicle disabled by a Warrantable Failure to the
nearest authorized repair location. In lieu of the towing expense, Cummins will pay reasonable costs for
mechanics to travel to and from the location of the
vehicle, including meals, mileage and lodging when
the repair is performed at the site of the failure.

Owner
Responsibilities
Owner is responsible for the operation and
maintenance of the Engine as specified in Cummins
Operation and Maintenance Manuals. Owner is also
responsible for providing proof that all recommended
maintenance has been performed.

Before the expiration of the applicable Warranty,
Owner must notify a Cummins distributor, authorized
dealer or other repair location approved by Cummins
of any Warrantable Failure and make the Engine
available for repair by such facility. Except for Engines disabled by a Warrantable Failure, Owner must also
deliver the Engine to the repair facility.

Service locations are listed on the Cummins Worldwide
Service Locator at cummins.com.

Owner is responsible for the cost of lubricating oil,
antifreeze, filter elements and other maintenance items provided during Warranty repairs unless such items
are not reusable due to the Warrantable Failure.

Owner is responsible for communication expenses,
meals, lodging and similar costs incurred as a result of a Warrantable Failure.

Owner is responsible for non-Engine repairs and for
‘‘downtime’’ expenses, cargo damage, fines, all
applicable taxes, all business costs and other losses
resulting from a Warrantable Failure.

Owner is responsible for a $100 (U.S. Dollars)
deductible per each service visit under this plan in the 3rd, 4th and 5th years of Base Engine Warranty. The
deductible will not be charged during the first 2 years of the Base Engine Warranty.

Limitations
Cummins is not responsible for failures or damage
resulting from what Cummins determines to be abuse
or neglect, including, but not limited to: operation
without adequate coolants or lubricants; overfueling;
overspeeding; lack of maintenance of lubricating,
cooling or intake systems; improper storage, starting,
warm-up, run-in or shutdown practices; unauthorized
modifications of the Engine.

Any unauthorized modifications to the aftertreatment
could negatively effect emissions certification and void Warranty.

Cummins is also not responsible for failures caused by
incorrect oil, fuel or diesel exhaust fluid or by water, dirt or other contaminants in the fuel, oil or diesel
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 exhaust fluid.

This Warranty does not apply to accessories supplied
by Cummins which bear the name of another
company. Such non-warranted accessories include, but
are not limited to: alternators, starters, fans, air
conditioning compressors, clutches, filters,
transmissions, torque converters, vacuum pumps,
power steering pumps, fan drives and air compressors.

Cummins branded alternators and starters are covered
for the first two years from the date of delivery of the Engine to the first user, or the expiration of the Base Engine Warranty, whichever occurs first.

Failures resulting in excessive oil consumption are not covered beyond the duration of the Coverage or
100,000 miles (160,935 kilometers) or 7,000 hours from
the date of delivery of the Engine to the first user,
whichever of the three occurs first. Before a claim for excessive oil consumption will be considered, Owner
must submit adequate documentation to show that
consumption exceeds Cummins published standards.

Failures of belts and hoses supplied by Cummins are
not covered beyond the first year from the date of
delivery of the Engine to the first user or the duration of the Warranty, whichever occurs first.

Parts used to repair a Warrantable Failure may be new
Cummins parts, Cummins approved rebuilt parts or
repaired parts. Cummins is not responsible for failures resulting from the use of parts not approved by
Cummins.

A new Cummins or Cummins approved rebuilt part
used to repair a Warrantable Failure assumes the
identity of the part it replaced and is entitled to the remaining Coverage hereunder.

Cummins Inc. reserves the right to interrogate
Electronic Control Module (ECM) data for purposes of
failure analysis.

CUMMINS DOES NOT COVER WEAR OR WEAROUT
OF COVERED PARTS.

CUMMINS IS NOT RESPONSIBLE FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES.

THIS WARRANTY AND THE EMISSION WARRANTY

SET FORTH HEREINAFTER ARE THE SOLE

WARRANTIES MADE BY CUMMINS IN REGARD TO
THESE ENGINES. CUMMINS MAKES NO OTHER

WARRANTIES, EXPRESS OR IMPLIED, OR OF

MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE.

This Warranty gives you specific legal rights, and you
may also have other rights which vary from state to
state.

Emission
Warranty
Products Warranted
This Emission Warranty applies to new Engines
marketed by Cummins that are used in the United
States** in vehicles designed for transporting persons
or property on a street or highway. This Warranty
applies to Engines delivered to the first user on or after September 1, 1992.

Coverage
Cummins warrants to the first user and each
subsequent purchaser that the Engine is designed,
built and equipped so as to conform at the time of sale by Cummins with all U.S. federal emission regulations
applicable at the time of manufacture and that it is free from defects in material or factory workmanship which
would cause it not to meet these regulations within the longer of the following periods: (A) Five years or
100,000 miles (160,935 kilometers) of operation,
whichever occurs first, as measured from the date of
delivery of the Engine to the first user or (B) The Base Engine Warranty.

If the vehicle in which the Engine is installed is
registered in the state of California, a separate
California Emission Warranty also applies.

Limitations
Failures, other than those resulting from defects in
material or factory workmanship, are not covered by
this Warranty.

Cummins is not responsible for failures or damage
resulting from what Cummins determines to be abuse
or neglect, including, but not limited to: operation
without adequate coolants or lubricants; overfueling;
overspeeding; lack of maintenance of lubricating,
cooling or intake systems; improper storage, starting,
warm-up, run-in or shutdown practices; unauthorized
modifications of the Engine.

Any unauthorized modifications to the aftertreatment
could negatively effect emissions certification and void Warranty.

Cummins is also not responsible for failures caused by
incorrect oil, fuel or diesel exhaust fluid or by water, dirt or other contaminants in the fuel, oil or diesel
exhaust fluid.

Cummins is not responsible for non-Engine repairs,
‘‘downtime’’ expenses, cargo damage, fines, all
applicable taxes, all business costs or other losses
resulting from a Warrantable Failure.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 Cummins Inc.

Box 3005
Columbus, IN 47202-3005
U.S.A.

Bulletin 3381161
Printed in U.S.A. Rev. 08/09
©2001 Cummins Inc.

CUMMINS IS NOT RESPONSIBLE FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES.
* Airport operated crash trucks and fire department
operated trucks employed to respond to fires,
hazardous material releases, rescue and other
emergency-type situations.
** United States includes American Samoa, the
Commonwealth of Northern Mariana Islands, Guam,
Puerto Rico and the U.S. Virgin Islands.

Cummins Inc.

Box 3005
Columbus, IN 47202-3005
U.S.A.

Bulletin 3381161
Printed in U.S.A. Rev. 08/09 2001 Cummins Inc.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 2/8/2010 WA0013

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.

This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This warranty does not apply to damage caused by corrosion.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4
Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

Fire and Rescue Apparatus
Coverage:

Lifetime Fifty (50) Year Structural Integrity
Custom Chassis Frame
Fifty (50) Years
(Expected Life of Apparatus)
Warranty Period
Ends After:

The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:

Custom chassis frame rail manufactured by Pierce shall be free from defects in material and workmanship
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.

Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.

3. BUYER'S EXCLUSIVE REMEDY.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This limited warranty excludes brake pads, brake rotors, seal boots and shock absorbers.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE
POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.

Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.

3. BUYER'S EXCLUSIVE REMEDY.
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce.

Three (3) Years
-or30,000 Miles
Warranty Period
Ends After:

Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 12/16/2013 WA0050
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES

ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.

Fire and Rescue Apparatus
Coverage:

Three (3) Year Material and Workmanship
TAK-4 Independent Front Suspension
Limited Warranty
Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

The TAK-4 Front Independent Suspension and Steering
Gears shall be free from defects in material and
workmanship.

1. LIMITED WARRANTY
(b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 Fire and Rescue Apparatus
Coverage:

SUPPLIER
Limited Warranty
Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

The Meritor axle shall be covered by Meritor as indicated in the attached Meritor warranty coverage description

1. LIMITED WARRANTY
(b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the purchaser who first puts the product in service ("Buyer"):
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:

This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

The exclusions listed in the attached Meritor warranty
description shall apply.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.

Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.

3. BUYER'S EXCLUSIVE REMEDY.
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce.

Five (5) Years Warranty Period
Ends After:

Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 6/29/2020 WA0384
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67

CUMMINS-MERITOR

COMMERCIAL

VEHICLE SYSTEMS

WARRANTY

COVERAGE FOR THE

UNITED STATES AND CANADA
MODEL YEAR 2024 VEHICLES
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 2 WARRANTY INFORMATION

TABLE OF CONTENTS
EFFECTIVE MODEL YEAR 2024 VEHICLES
Linehaul.......................................................................................................3 General Service ...........................................................................................6 Heavy Service/Specialty Vehicle ..................................................................9 Fire and Emergency................................................................................... 12 Transit Bus ................................................................................................ 14 Off-highway Service................................................................................... 15 Terms and Conditions................................................................................ 17 How to Read Warranty Coverage
Number of Years Mileage (in thousands)
Unl = Unlimited
P = Parts Only
P&L = Parts and Labor
Notice:

Models or components that are approved for use by Cummins-Meritor’s vocational guidelines contained in Cummins-Meritor publication TP-9441 for axles, SP-8320 for trailer axles and TP-12126 for drivelines, or any other products that have an application approval completed with Cummins-Meritor which are not specifically listed, are warranted for one year, unlimited miles, parts only (1/Unl/P).

Products purchased on an incomplete vehicle (glider) are limited to one year, unlimited miles, parts only (1/Unl/P).

Advantage Program
Purchasing additional coverage on select components will continue to safeguard your investment against major repair costs after the initial base coverage expires. You can find out more about the Advantage Program by visiting meritor.com or by contacting Cummins-Meritor at 866-OnTrac1 (866-668-7221).

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 3 Linehaul Vehicles
Auto Hauler1
Bulk Hauler1
Chip Hauler1,2
Doubles
Flatbed
General Freight
Grain Hauler1
Livestock Hauler
Moving Van
Pipe Hauler
Refrigerated Freight
Tanker1
Triples
1 Cummins-Meritor classifies these vehicle types as high center of gravity, which require special axle housing considerations. 2 Chip Hauler vehicles require specific axle models listed below and Linehaul condition to be eligible for Linehaul warranty consideration.

Linehaul Typically Is:

High mileage operation (over 60,000 miles/year)
Greater than 30 miles between starts and stops
Maximum grades of 12%
Well maintained highways of concrete or asphalt construction (100% on-road)
Category A job sites, terminals, docks and transfer sites (defined as pavement, concrete or maintained and hard packed gravel).

Note:Category B job sites, terminals, docks, transfer sites (defined as loose or unmaintained sand, dirt or gravel; landfill; farm field; mud; or other similar surfaces) are NOT approved for certain linehaul axle models.

Front Non-Drive Steer Axles – 5/750/P&L
FD-965
FF-941
FF-942
FF-943
FF-944
FF-961
FF-966
FF-967
FG-941
FG-943
MFS-10-122A
MFS-10-143A-N
MFS-10-144A-N
MFS-12-122A-N
MFS-12-122B-N
MFS-12-122C-N
MFS-12E-122A-N
MFS-12E-122B-N
MFS-12E-122C-N
MFS-12-124A-N
MFS-12-132B-N
MFS-12-132C-N
MFS-12E-132B-N
MFS-12E-132C-N
MFS-12-143A-N
MFS-12E-143A-N
MFS-12-144A-N
MFS-13-122A-N
MFS-13-122B-N
MFS-13-122C-N
MFS-13-132B-N
MFS-13-132C-N
MFS-13-143A-N
MFS-13-144A-N
MFS-13B-122B-N
MFS-13B-122C-N
MFS-13B-132B-N
MFS-13B-132C-N
MFS-14-122A-N
MFS-14-122B-N
MFS-14F-122B-N
MFS-14G-122B-N
MFS-14-122C-N
MFS-14F-122C-N
MFS-14G-122C-N
MFS-14-124A-N
MFS-14-132B-N
MFS-14F-132B-N
MFS-14G-132B-N
MFS-14-132C-N
MFS-14F-132C-N
MFS-14G-132C-N
MFS-14-142B-N
MFS-14F-142B-N
MFS-14G-142B-N
MFS-14-142C-N
MFS-14F-142C-N
MFS-14G-142C-N
MFS-14-143A-N
MFS-14-144A-N
Rear Drive Single Axles – 5/750/P&L
MS-19-14X
RS-21-160
MS-23-17H1,2
MS-23-17X2
RS-23-160
RS-23-161
RS-23-185
RS-23-186
Coverage under Cummins-Meritor’s warranty require that
the application of products be properly approved pursuant to OEM and Cummins-Meritor approvals. Refer to TP-9441
for axles, SP-8320 for trailer axles, TP-12126 for drivelines and/or contact Cummins-Meritor regarding specific
application approval questions on any product line.

LINEHAUL

WARRANTY INFORMATION
Vocational Definition of Linehaul
Long distance hauling of food, goods and finished materials Not included are raw ferrous materials, minerals (except oil), sand, gravel, stone, rocks, topsoil, waste or logs Linehaul includes turnpike and hub & spoke
1 Not approved for use in any Category B job sites, terminals, docks or transfer sites. 2 Recommend 11 mm minimum wall thickness for these models used in combination with high center of gravity vehicles and trailing arm suspensions or vehicles operating mainly in Canada.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 4 Trailer Axles1
Beam and Brackets 5/500/P, 1/100/L
TPX3000 Axle Series2 10/Unl/P, 1/Unl/L
Wheel End Systems3
Standard System4 1/100/P&L
AxlePak5 5/Unl/P&L
AxlePak75 7/Unl/P&L
1 For brake components and ABS coverage, refer to appropriate product warranties. 2 Structural components only excluding spindle wear. Spindle wear is 5/Unl/P, 1/Unl/L.
3 Includes hub, wheel seals and wheel bearings—all systems require annual inspections and proper documentation to ensure full coverage. 4 When installed by Cummins-Meritor. 5
When specified with AxlePak7 wheel end system, coverage on Meritor Tire Inflation System (MTIS) thru-tee and stator is 7/Unl/P, 1/Unl/L.

TAG/Pusher Axles1
TQ, TR Beam and Brackets 5/750/P&L
1 For brake components and ABS coverage, refer to appropriate product warranties.

Trailer Mechanical Suspension
Systems1
IMS40 (Integrated Mechanical Suspension – Tandem)2 1/Unl/P&L IMS20 (Integrated Mechanical Suspension – Single)2 1/Unl/P&L 1 For axle coverage, refer to appropriate product warranties. 2 All other suspension components refer to appropriate manufacturer’s warranty.

Trailer Air Suspension Systems
MPA40 (Tandem Axle Parallelogram)1
Major Structural Components 5/500/P, 1/100/L
Curbing Damage Warranty2 5/500/P, 1/100/L
Height Control Valve 1/100/P&L
Shock Absorbers 2/200/P&L
Air Springs 2/200/P, 1/100/L
Bushings 5/Unl/P, 3/Unl/L
PinLoc Air Controls 1/100/P&L
PinLoc Actuator 3/300/P&L
MPA20 (Single Axle Parallelogram)
Major Structural Components 5/500/P, 1/100/L
Height Control Valve 1/100/P&L
Shock Absorbers 2/200/P&L
Air Springs 2/200/P, 1/100/L
Bushings 5/Unl/P, 3/Unl/L
MTA and MTA-Tec6 Trailing Arm Suspension System
Major Structural Components 5/500/P, 1/100/L
Height Control Valve 1/100/P&L
Air Springs 2/200/P, 1/100/L
Bushings 5/500/P, 3/300/L
Shock Absorbers 2/200/P&L
Lift Kit System 1/100/P&L
1 Fastener torque coverage is limited to 2/Unl/P&L when torqued by CumminsMeritor (For axle and ABS coverage, refer to appropriate product warranties.) 2 “Curbing damage” is defined as deformation (bending, buckling or breakage), caused by sudden impact with a curb or similar fixed object. Damage to the RideSentry slider box (the suspension sliding sub-frame consisting of the frame rails, cross-members and central A-frame assembly), caused by accidental trailer impact with a curb or similar fixed object, is eligible for warranty coverage. Damage to other components or resulting from collision with another vehicle, rollover or fire is not covered under this provision. Warranty is not transferable to another trailer VIN and coverage does not apply if the trailer is deemed to be a total loss, scrapped or otherwise not salvageable.

LINEHAUL

WARRANTY INFORMATION
Rear Drive Tandem/Tridem Axles – 5/750/P&L
RT-40-160/P1,2
RT-46-160/P1,2
RT-46-164/P1,2
RZ-1662
RT-50-160/P1,2
MA-40-165
MA-40-17H3
RZ-188
MA-40-175
MT-34-14X/P4
MT-40-14T/P
MT-40-14X/P4
MT-40-14X/P4
MT-40-14H/E3,4
1 These models required for Chip Hauler and Linehaul warranty consideration. 2 Each vehicle must have a Request for Application Recommendation (RAR) approved by Cummins-Meritor prior to vehicle build. All RARs must identify the chassis number or VIN. Refer to Product Information Letter #303 and #396 for further details. 3 Not approved for use in any Category B job sites, terminals, docks or transfer sites. 4 Recommend 11 mm minimum wall thickness for these models used in combination with high center of gravity vehicles and trailing arm suspensions or vehicles operating mainly in Canada.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 5 LINEHAUL

WARRANTY INFORMATION
Brake Components
Cam Q Series Trailer Brakes 5/500/P, 1/100/L
Q+ Drum Brake™1 5/500/P, 1/Unl/P&L
ASA 5/500/P, 1/Unl/P&L
Hubs/Cast Drums and Other Wheel-End Components 1/Unl/P
Hydraulic Disc Brakes 1/Unl/P
All Other Brakes 1/Unl/P
STEELite X30 Drum Brake™2 12-Years or Wearable Life/P
EX+ L and EX+LS Air Disc Brake™3 5/500/P, 1/Unl/L
EX+L Air Disc Brake Extended Standard Warranty3,4 5/500/P&L 1 For Trailer only, 3/300/P against rust jacking when equipped with Platinum Shield III. 2
Based on stamped wear diameter max. 3
Warranty coverage for boots, seals, caps, bushings and pins is 2/200/P.

Warranty coverage for pads is 1/100/P. 4
Applies only to calipers using friction: MA9300 (EX225LXXXCGXXX).

Drivelines
RPL 5/500/P, 1/Unl/P&L
MXL 3/350/P, 1/Unl/P&L
92N 1/Unl/P
Meritor Tire Inflation System
(MTIS)
MTIS Components 5/Unl/P, 1/Unl/L
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 6 General Service Vehicles
Auto Hauler
Beverage Truck
Bulk Hauler
Chip Hauler
Cross Country Coach
Flatbed
Front Engine Commercial
Chassis
Front Engine Integral Coach
General Freight
Grain Hauler
Intercity Coach
Intermodal Chassis
Livestock Hauler
Meat Packer
Moving Van
Municipal Truck
Newspaper Delivery
Pick-Up and Delivery
Pipe Hauler
Platform Auto Hauler
Rear Engine Integral Coach
Recreational Vehicles
Refrigerated Freight
School Bus
Stake Truck
Tanker
Tanker Trailer
Tour Bus
Wrecker
General Service Typically Is:

Typically, moderate mileage operation (less than 60,000 miles/year) An average of 3 to 30 miles between starts and stops
Maximum grades of 12%
Generally, on-road service (less than 10% off-road allowed) Category A job sites, terminals, docks and transfer sites (defined as pavement, concrete or maintained and hard packed gravel) or Category B job sites, terminals, docks and transfer sites (defined as loose or unmaintained sand, dirt or gravel; landfill; farm field; mud, or other similar surfaces)
Front Non-Drive Steer Axles – 2/Unl/P&L
FD-965
FF-941
FF-942
FF-943
FF-944
FF-946
FF-961
FF-966
FF-967
FG-941
FH-941
FH-9461
FL-941
FL-943
MFS-6-151A-N
MFS-6-153B-N
MFS-6-162B-N
MFS-6-153C-N
MFS-6-162C-N
MFS-7-113C-N
MFS-7-153C-N
MFS-7-163C-N
MFS-8-113B-N
MFS-8-143A-N
MFS-8-153B-N
MFS-8-163B-N
MFS-10-122A
MFS-10-143A-N
MFS-10-144A-N
MFS-12-122A-N
MFS-12E-122A-N
MFS-12-122B-N
MFS-12E-122B-N
MFS-12-122C-N
MFS-12E-122C-N
MFS-12-124A-N
MFS-12-132B-N
MFS-12E-132B-N
MFS-12-132C-N
MFS-12E-132C-N
MFS-12-143A-N
MFS-12-144A-N
MFS-12E-143A-N
MFS-13-122A-N
MFS-13-122B-N
MFS-13B-122B-N
MFS-13-122C-N
MFS-13B-122C-N
MFS-13-132B-N
MFS-13-132C-N
MFS-13B-132B-N
MFS-13B-132C-N
MFS-13-143A-N
MFS-13-144A-N
MFS-14-122A-N
MFS-14-122B-N
MFS-14F-122B-N
MFS-14G-122B-N
MFS-14-122C-N
MFS-14F-122C-N
MFS-14G-122C-N
MFS-14-124A-N
MFS-14-132B-N
MFS-14F-132B-N
MFS-14G-132B-N
MFS-14-132C-N
MFS-14F-132C-N
MFS-14G-132C-N
MFS-14-142B-N
MFS-14F-142B-N
MFS-14G-142B-N
MFS-14-142C-N
MFS-14F-142C-N
MFS-14G-142C-N
MFS-14-143A-N
MFS-14-144A-N
MFS-16-122A-N
MFS-16-133A-N
MFS-16-135A-N
MFS-16-143A-N
MFS-18-133A-N
MFS-18-135A-N
MFS-18-193A-N
MFS-20-133A-N
MFS-20-135A-N
MFS-20-192A-N
MFS-20-193A-N
MFS-22-135A-N
MFS-22H-135A-N
MFS-22-193A-N
MFS-22H-193A-N
1 Can also be used with reduced steer angles in tag position in Coach applications.

GENERAL SERVICE

WARRANTY INFORMATION
Coverage under Cummins-Meritor’s warranty require that
the application of products be properly approved pursuant to OEM and Cummins-Meritor approvals. Refer to TP-9441
for axles, SP-8320 for trailer axles, TP-12126 for drivelines and/or contact Cummins-Meritor regarding specific
application approval questions on any product line.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 7 GENERAL SERVICE

WARRANTY INFORMATION
Rear Drive Tandem/Tridem Axles – 2/Unl/P&L
MT-34-14X/P
MT-40-14T/P
MT-40-14X/P
MT-44-14X/P
RT-46-169
MT-52-616
RT-52-1851
MT-58-616
RT-58-1851
MT-70-380
RZ-188
1 Each vehicle must have a Request for Application Recommendation (RAR) approved by Cummins-Meritor prior to vehicle build. All RARs must identify the chassis number or VIN. Refer to Product Information Letter #303 and #396 for further details.

Rear Drive Tandem/Tridem – 3/Unl/P&L
RT-40-160/P RT-46-160/P RT-46-164/P RT-50-160/P RZ-166
Rear Drive Axles – 1/Unl/P&L
RND-14H RND-16A
PTO – 1/Unl/P&L
MPT-170
MPT-180
MPT-185
MPT-309
MPT-500
MPT-518
MPT-1702
Brake Components
Cam Q Series Trailer Brakes1 3/Unl/P, 1/Unl/L
Cam P2 2/200/P
Cam 3/Unl/P
Q+ Drum Brake™ 3/Unl/P&L
Q+ Drum Brake™1,2 2/200/P&L
ASA 3/Unl/P
ASA2 2/200/P
Hubs/Cast Drums and Other Wheel-End Components 1/Unl/P
Hydraulic Disc Brakes 1/Unl/P
All Other Brakes 1/Unl/P
STEELite X30 Drum Brake™3 12-Years or Wearable Life/P
EX+ Air Disc Brake™4 2/Unl/P&L
1 For Trailer only, 3/300/P against rust jacking when equipped with Platinum Shield III or Chassis Protect. 2
Applies to Tour Bus and Cross Country Coach only. 3
Based on stamped wear diameter max. 4
Warranty coverage for boots, seals, caps, bushings and pins is 2/200/P.

Warranty coverage for pads is 1/100/P.

Drivelines
RPL 4/400/P, 1/Unl/P&L
MXL 3/350/P, 1/Unl/P&L
92N 1/Unl/P
Rear Drive Single Axles – 2/Unl/P&L
MS-17-13X
MS-17-14X
MS-19-13X
MS-19-14X
MS-21-13X
MS-21-14X
MS-23-17X
RS-21-160
RC-23-160
RC-23-161
RC-23-1621
RC-23-1651
RS-23-160
RS-23-161
RS-23-185
RS-23-186
RS-24-160
RC-25-160
RS-26-185
MS-26-616
MS-26-616-SP
RS-30-185
MS-30-616
MS-30-616-SP
RS-35-380
1 3/Unl/P&L if PreSet by Cummins-Meritor.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 8 Trailer Axles1
Beam and Brackets2 5/Unl/P, 1/Unl/L
TPX4000 Axle Series3 10/Unl/P, 1/Unl/L
Wheel End Systems4
Standard System5 1/Unl/P&L
AxlePak5 5/Unl/P&L
AxlePak76 7/Unl/P&L
AxlePak107 10/Unl/P&L
1 For brake components and ABS coverage, refer to appropriate product warranties.
2 9000 Series is 3/Unl/P, 1/Unl/L
3 Structural components only excluding spindle wear. Spindle wear 5/Unl/P, 1/Unl/L. 4
Includes hub, wheel seals and wheel bearings—all systems require annual inspections and proper documentation to ensure full coverage. 5 When installed by Cummins-Meritor. 6
When specified with AxlePak7 wheel end system, coverage on Meritor Tire Inflation System (MTIS) thru-tee and stator is 7/Unl/P, 1/Unl/L. 7 AxlePak10 is limited to Intermodal Chassis applications equipped with TPX4000 series axles.

TAG/Pusher Axles1
TQ, TR Beam and Brackets 3/Unl/P, 1/Unl/L
MC14002, MC16003, FH9462 2/Unl/P&L
1 For brake components coverage, refer to appropriate product warranties. 2 3/Unl/P&L if sold with PreSet by Cummins-Meritor.

Meritor Tire Inflation System
(MTIS)
MTIS Components 5/Unl/P, 1/Unl/L
Trailer Mechanical Suspension
Systems1
IMS40 (Integrated Mechanical Suspension – Tandem)2 1/Unl/P&L IMS20 (Integrated Mechanical Suspension – Single)2 1/Unl/P&L 1 For axle coverage, refer to appropriate product warranties. 2 All other suspension components refer to appropriate manufacturer’s warranty.

Trailer Air Suspension Systems1
MPA40 (Tandem Axle Parallelogram)2
Major Structural Components 5/Unl/P, 1/Unl/L
Curbing Damage Warranty3 5/500/P, 1/100/L
Height Control Valve 1/Unl/P&L
Shock Absorbers 2/Unl/P&L
Air Springs 2/Unl/P, 1/Unl/L
Bushings 5/P, 3/L
PinLoc Air Controls 1/Unl/P&L
PinLoc Actuator 3/Unl/P&L
MPA20 (Single Axle Parallelogram)
Major Structural Components 5/Unl/P, 1/Unl/L
Height Control Valve 1/Unl/P&L
Shock Absorbers 2/Unl/P&L
Air Springs and Rebound Straps 2/Unl/P, 1/Unl/L
Bushings 5/P, 3/L
MTA and MTA-Tec6 Trailing Arm Suspension System
Major Structural Components 5/Unl/P, 1/Unl/L
Height Control Valve 1/Unl/P&L
Air Springs 2/Unl/P, 1/Unl/L
Bushings4 5/Unl/P, 3/Unl/L
Shock Absorbers 2/Unl/P&L
Lift Kit System 1/Unl/P&L
1 For axle coverage, refer to appropriate product warranties. 2 Fastener torque coverage is limited to 2/Unl/P&L when torqued by CumminsMeritor. 3 “Curbing damage” is defined as deformation (bending, buckling or breakage), caused by sudden impact with a curb or similar fixed object. Damage to the RideSentry slider box (the suspension sliding sub-frame, consisting of the frame rails, cross-members and central A-frame assembly), caused by accidental trailer impact with a curb or similar fixed object, is eligible for warranty coverage. Damage to other components or damage resulting from collision with another vehicle, rollover or fire is not covered under this provision. Warranty is not transferable to another trailer VIN and coverage does not apply if the trailer is deemed to be a total loss, scrapped or otherwise not salvageable. 4 Raw wood applications 3/Unl/P, 1/Unl/L

GENERAL SERVICE

WARRANTY INFORMATION
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 9 Heavy Service/Specialty Vehicles
Airport Rescue Fire
Fighting (ARFF)
Airport Shuttle1
Asphalt Truck
Block Truck
Bottom Dump Trailer
Combination
Cementing Vehicle
Commercial Pick-Up
Concrete Pumper
Construction Material Hauler
Mixer
Demolition
Drill Rig
Dump
Equipment Hauling
Flatbed Trailer Hauler
Flatbed Truck
Fracturing Truck
Front Loader
Geophysical Exploration
Hopper Trailer Combinations
Landscaping Truck
Liquid Waste Hauler
Log Hauling
Lowboy
Michigan Special Gravel
Train
Michigan Special Log Hauler
Michigan Special Steel
Hauler
Michigan Special Waste
Vehicle
Municipal Dump
Rear Loader (Refuse)
Recycling Truck
Residential Pick-Up (Refuse)
Rigging Truck
Roll-Off
Scrap Truck
Semi-End Dump
Sewer/Septic Vacuum
Shuttle Bus1
Side Loader
Snowplow/Snowblower
Steel Hauling
Tanker
Tank Truck
Tractors with Pole Trailers
Tractor/Trailer with Jeeps
Transfer Dump
Transfer Vehicle
Utility Truck
Winch Truck
1 Commercial chassis only
Heavy Service/Specialty Vehicle
Typically Is:

Moderate mileage operation (less than 60,000 miles per year) On/off-road vocations (10% or more off-road)
Moderate to frequent stops/starts (up to 10 stops per mile) An average of three (3) miles between starting and stopping Front Non-Drive Steer Axles – 2/Unl/P&L
FD-965
FF-941
FF-942
FF-943
FF-944
FF-946
FF-961
FF-966
FF-967
FG-941
FG-943
FH-941
FH-946
FL-941
FL-943
MFS-6-151A-N
MFS-6-153B
MFS-6-162B
MFS-6-162C
MFS-7-113C-N
MFS-7-153C-N
MFS-7-163C-N
MFS-8-113B-N
MFS-8-153B-N
MFS-8-163B-N
MFS-10-122A
MFS-10-143A-N
MFS-10-144A-N
MFS-12-122
MFS-12E-122
MFS-12-122B-N
MFS-12E-122B-N
MFS-12-122C-N
MFS-12E-122C-N
MFS-12-124A-N
MFS-12-132B-N
MFS-12E-132B-N
MFS-12-132C-N
MFS-12E-132C-N
MFS-12-143A-N
MFS-12-144A-N
MFS-12-155
MFS-13-122
MFS-13-122B-N
MFS-13B-122B-N
MFS-13-122C-N
MFS-13B-122C-N
MFS-13-132B-N
MFS-13B-132B-N
MFS-13-132C-N
MFS-13B-132C-N
MFS-13-143A-N
MFS-13-144A-N
MFS-13-155
MFS-14-122
MFS-14-122B-N
MFS-14F-122B-N
MFS-14G-122B-N
MFS-14-122C-N
MFS-14F-122C-N
MFS-14G-122C-N
MFS-14-124A-N
MFS-14-132B-N
MFS-14F-132B-N
MFS-14G-132B-N
MFS-14-132C-N
MFS-14F-132C-N
MFS-14G-132C-N
MFS-14-142B-N
MFS-14F-142B-N
MFS-14G-142B-N
MFS-14-142C-N
MFS-14F-142C-N
MFS-14G-142C-N
MFS-14-143A-N
MFS-14-144A-N
MFS-16-122A-N
MFS-16-133A-N
MFS-16-135A-N
MFS-16-143A-N
MFS-18-133A-N
MFS-18-135A-N
MFS-18-192A-N
MFS-18-193A-N
MFS-20-133A-N
MFS-20-135A-N
MFS-20-192A-N
MFS-20-193A-N
MFS-22-135A-N
MFS-22H-135A-N
MFS-22-193A-N
MFS-22H-193A-N
RF-16-145
RF-21-160

HEAVY SERVICE/SPECIALTY VEHICLE

WARRANTY INFORMATION
Coverage under Cummins-Meritor’s warranty require that
the application of products be properly approved pursuant to OEM and Cummins-Meritor approvals. Refer to TP-9441
for axles, SP-8320 for trailer axles, TP-12126 for drivelines and/or contact Cummins-Meritor regarding specific
application approval questions on any product line.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 10 Rear Drive Axles – 2/Unl/P&L
MS-17-14X
MS-19-14X
MS-21-14X
RS-21-160
RC-23-160
RH-23-160
RS-23-160
RC-23-161
RS-23-161
RS-23-185
RS-23-186/380
RS-24-160
RC-25-160
RS-25-160
MS-26-616
MS-26-616-SP
RS-26-185/380
RC-26-633
MS-30-616
MS-30-616-SP
RS-30-185/380
MS-35-380
RS-38-380
MT-58-616
MT-58-616-SP
Rear Drive Axles – 1/Unl/P&L
RND-14H RND-16A
Rear Drive Tandem/Tridem Axles – 2/Unl/P&L
MT-34-14X/P
MT-40-14T/P
MT-40-14X/P
MT-44-14X/P
RT-46-169
RT-58-160
MT-52-616
MT-52-616-SP
RT-52-185/3801,2
MT-58-616
MT-58-616-SP
RT-58-185/3801,2
RT-70-380
MT-70-380
RZ-188
1 Axle model designated will vary according to options and variations specified on these axles. Contact Cummins-Meritor Axle Applications Engineering for details. 2 Each vehicle must have a Request for Application Recommendation (RAR) approved by Cummins-Meritor prior to vehicle build. All RARs must identify the chassis number or VIN. Refer to Product Information Letter #303 and #396 for further details.

Rear Drive Tandem/Tridem – 3/Unl/P&L
RT-40-160/P/A3 RT-46-160/P/A1,3 RT-46-164/P2,3 RT-50-160/P/A3 RZ-166 1 U.S. only. Canadian warranty = 1/Unl/P for combination vehicles only. 2 Axle model designated will vary according to options and variations specified on these axles. Contact Cummins-Meritor Axle Applications Engineering for details. 3 Each vehicle must have a Request for Application Recommendation (RAR) approved by Cummins-Meritor prior to vehicle build. All RARs must identify the chassis number or VIN. Refer to Product Information Letter #303 and #396 for further details.

Front Drive Steer Axles – 1/Unl/P&L
MX-08-130-FV (FSD-08A)
MX-10-130-FV (FSD-10A)
MX-12-130-FV (FSD-12A)
MX-13-130-FV (FSD-13A)
MX-14-130-FV (FSD-14A)
MX-16-130-FV (FSD-16A)
MX-18-130-FV (FSD-18A)
MX-18-130-SD (SDA-1800)
MX-20-130-FV (FSD-20A)
MX-21-130-FV (FSD-21A)
MX-21-130-SD (SDA-2100)
MX-23-130-FV (FSD-23A)
MX-23-130-SD (SDA-2300)

HEAVY SERVICE/SPECIALTY VEHICLE

WARRANTY INFORMATION
MX-10-120
MX-10-120 EVO
MX-12-120
MX-12-120 EVO
MX-14-120
MX-14-120 EVO
MX-16-120
MX-18-120
MX-17-140
MX-19-140
MX-21-140
MX-21-160
MX-23-160
MX-23-810
Front Drive Steer Axles – 2/Unl/P&L
MPT-170
MPT-180
MPT-185
MPT-309
MPT-500
MPT-518
MPT-1702
PTO – 1/Unl/P&L
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 11 Drivelines
RPL 3/Unl/P, 1/Unl/P&L
92N 1/Unl/P&L
MXL 1/Unl/P&L
Transmission – 1/Unl/P&L
FAT 30
Brake Components
Cam P 3/Unl/P
Cam P 2/100/P
Cam Cast Plus™ 2/100/P&L
Q+ Drum Brake™1 3/Unl/P&L
Q+ Drum Brake™2 2/100/P&L
ASA 3/Unl/P
ASA2 2/100/P
Hubs/Cast Drums and Other Wheel-End Components3 1/Unl/P Hydraulic Disc Brakes 1/Unl/P
All Other Brakes 1/Unl/P
EX+ Air Disc Brake4 2/100/P&L
1 For Trailer only, 3/300/P against rust jacking when equipped with Platinum Shield III. 2
Applies to City Bus, Trolley, Shuttle Bus and Airport Shuttle only. 3 Based on stamped wear diameter max. 4
Warranty coverage for boots, seals, caps, bushings and pins is 2/100/P.

Warranty coverage for pads is 1/100/P.

Trailer Axles1
Beam and Brackets2 5/Unl/P, 1/Unl/L
Wheel End Systems3
Standard System4 1/Unl/P&L
1 For brake components coverage, refer to appropriate product warranties. 2 9000 Series is 3/Unl/P, 1/Unl/L 3 Includes hub, wheel seals and wheel bearings—all systems require annual inspections and proper documentation to ensure full coverage. 4 When installed by Cummins-Meritor.

Trailer Air Suspension Systems1
MTA and MTA-Tec6 Trailing Arm Suspension System
Major Structural Components2 5/500/P, 1/100/L
Height Control Valve 1/100/P&L
Air Springs 2/200/P, 1/100/L
Bushings2 5/500/P, 3/300/L
Shock Absorbers 2/200/P&L
Lift Kit System 1/100/P&L
1 For axle coverage, refer to appropriate product warranties. 2 Raw wood applications 3/Unl/P, 1/Unl/L
Meritor Tire Inflation System
(MTIS)
MTIS Components 5/Unl/P, 1/Unl/L
Gearboxes – 1/Unl/P&L
MGX-402
MGX-423
MGX-450
MGX-451
MGX-466
MGX-479
MGX-538
Transfer Cases – 1/Unl/P
MTC-2212-CV (306)
MTC-3106-FV (TC-137)
MTC-3111 (T-2111)
MTC-3112-CV (548C)
MTC-3116 (T-2111 through-shaft)
MTC-3118-FV (TC-180 and TC-180-23)
MTC-3118-CV (358)
MTC-3120-FV (TC-143)
MTC-3124 (T-2119)
MTC-3203
MTC-3205-GV (MTC-25/RTC-25)
MTC-3206-FV (TC-237)
MTC-3206-CS (544)
MTC-3208-GV (RTC-50)
MTC-3209-GV (MTC-60/RTC-60)
MTC-3212-CV (315 and 548B)
MTC-3312-FV (TC-270)
MTC-3220-FC (TC-142)
MTC-4206-FV (TC-38)
MTC-4208
MTC-4210
MTC-4213

HEAVY SERVICE/SPECIALTY VEHICLE

WARRANTY INFORMATION
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 12 Fire and Emergency Vehicles
Aerial Ladder Truck
Aerial Platform
Ambulance
Command Vehicle
Crash Fire Rescue
Pumper
Rapid Intervention
Vehicle (RIV)
Tanker
Fire and Emergency Typically Is:

Lower mileage operations (less than 20,000 miles/year)
Generally, on-road service (less than 10% off-road)
An average of three (3) miles between starting and stopping Front Non-Drive Steer Axles – 5/Unl/P&L
FL-941
FL-943
MFS-18-133A-N
MFS-18-135A-N
MFS-18-193A-N
MFS-20-133A-N
MFS-20-135A-N
MFS-20-193A-N
MFS-22-135A-N
MFS-22H-135A-N
MFS-22-193A-N
MFS-22H-193A-N
Rear Drive Single Axles – 5/Unl/P&L
RC-23-160
RS-23-160
RS-23-161
RS-23-185
RS-23-186
RS-24-160
RC-25-160
RS-26-185
RS-30-185
RS-35-1851
RS-25-160
1 2/Unl/P&L if PreSet by Cummins-Meritor.

Rear Drive Tandem/Tridem Axles – 5/Unl/P&L
MT-40-14X/P
RT-40-160/P
MT-44-14X/P
RT-46-160/P
RT-46-164/P
RT-46-169
RT-50-160/P
MT-52-616
RT-52-1851
MT-58-616
RT-58-1851
MT-70-3802
1 Each vehicle must have a Request for Application Recommendation (RAR) approved by Cummins-Meritor prior to vehicle build. All RARs must identify the chassis number or VIN. Refer to Product Information Letter #303 and #396 for further details. 2 2/Unl/P&L Front Drive Steer Axles – 2/Unl/P&L
MX-19-140 MX-21-140 MX-21-160 MX-23-160 MX-23-810

FIRE AND EMERGENCY

WARRANTY INFORMATION
Coverage under Cummins-Meritor’s warranty require
that the application of products be properly approved
pursuant to OEM and Cummins-Meritor approvals.

Refer to TP-9441 for axles, TP-12126 for drivelines
and/or contact Cummins-Meritor regarding specific
application approval questions on any product line.

Transfer Cases – 1/Unl/P
MTC-2212-CV (306)
MTC-3106-FV (TC-137)
MTC-3111 (T-2111 through-shaft)
MTC-3112-CV (548C)
MTC-3118-FV (TC-180 and TC-180-23)
MTC-3118-CV (358)
MTC-3120-FV (TC-143)
MTC-3124 (T-2119)
MTC-3206-FV (TC-237)
MTC-3206-CS (544)
MTC-3208-GV (RTC-50)
MTC-3209-GV (MTC-60/RTC-60)
MTC-3212-CV (315 and 548B)
MTC-3312-FV (TC-270)
MTC-3220-FC (TC-142)
MTC-4206-FV (TC-38)
MTC-4208
MTC-4210
MTC-4213
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 13 PTO – 1/Unl/P&L
MPT-170
MPT-180
MPT-185
MPT-309
MPT-500
MPT-518
MPT-1702

FIRE AND EMERGENCY

WARRANTY INFORMATION
Brake Components
Cam 3/Unl/P
Q+ Drum Brake™ 3/Unl/P&L
ASA 3/Unl/P
Hubs/Cast Drums and Other Wheel-End Components 1/Unl/P
Hydraulic Disc Brakes 1/Unl/P
All Other Brakes 1/Unl/P
EX+ Air Disc Brake™1 2/Unl/P&L
1 Warranty coverage for boots, seals, caps, bushings and pins is 2/200/P.

Warranty coverage for pads is 1/100/P.

Drivelines
RPL 4/400/P, 1/Unl/L
MXL 3/350/P, 1/Unl/L
92N 1/Unl/P
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 14 Transit Bus Vehicles
Airport Shuttle
City Bus
Commuter Coach
Shuttle Bus
Transit Bus Trolley
Transit Bus Typically Is:

Moderate mileage operation (less than 50,000 miles per year) Moderate to frequent stops/starts (up to 10 stops per mile) Front Non-Drive Steer Axles – 5/300/P&L
FH-946 FH-9411 MFS-12-155 MFS-13-155
1 Commuter coach only – 2/Unl/P&L
Tag Axles – 2/Unl/P&L
Brake Components
Cam Cast Plus™ 2/100/P&L
Q+ Drum Brake™1 2/100/P&L
ASA1 2/100/P
Hubs/Cast Drums and Other Wheel-End Components 1/Unl/P
All Other Brakes 1/Unl/P
EX+ Air Disc Brake2 2/100/P&L
1 Applies to City Bus, Trolley, Shuttle Bus and Airport Shuttle only. 2 Warranty coverage for boots, seals, caps, bushings and pins is 2/100/P.

Warranty coverage for pads is 1/100/P.

Drivelines
RPL 3/Unl/P, 1/Unl/L
92N 1/Unl/P&L
MXL 1/Unl/P&L
1 Commuter coach only – 2/Unl/P&L
Rear Drive Single Axles – 5/300/P&L
RS-23-160
RC-23-161
71163
79163
RC-23-1621
RC-23-1651
RS-21-160
MC-14002 MC-16003 FH-946
Center Non-drive Axles – 5/300/P&L
MC-26000 71063 79063
Gearboxes – 1/Unl/P&L
MGX-450 MGX-451 MGX-538

TRANSIT BUS

WARRANTY INFORMATION
Coverage under Cummins-Meritor’s warranty require
that the application of products be properly approved
pursuant to OEM and Cummins-Meritor approvals.

Refer to TP-9441 for axles, TP-12126 for drivelines
and/or contact Cummins-Meritor regarding specific
application approval questions on any product line.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 15 Industrial and Off-Highway Service Vehicles
Load-On/Load-Off
Port Tractor
Rail Yard Spotter
Roll-On/Roll-Off
Stevedoring Tractor
Trailer Spotter
Yard Jockey
All and Rough
Terrain Cranes
Forestry
Material Handling
Specialized Heavy
Haul
Excavator
Compactor
Fertilizer Spreader
Snow Blower
Mining and
Specialized Mining
Rail Car Mover
Loader
Tow Tractor
Pushback Tractor
Industrial and Off-Highway Service Typically Is:

Low mileage operation
Low speed vehicle speed restriction
Vehicles are not typically licensed for highway use
Six (6) starts/stops per mile (typical)
Front Non-Drive Steer Axles – 1/Unl/P
FF - 941
FF - 943
FF - 961
FF - 966
FG - 941
FG - 943
FL - 941
FL - 943
FN - 951
FS-25
MFS-20-133A-N
MFS-20-135A-N
MFS-20-192A-N
MFS-20-193A-N
MFS-22-135A-N
MFS-22H-135A-N
MFS-22-193A-N
MFS-22H-193A-N
MON-Z0 FAMILY
Gearboxes – 1/Unl/P&L
MGX-402
MGX-423
MGX-450
MGX-451
MGX-466
MGX-479
MGX-538
PTO – 1/Unl/P&L
MPT-170
MPT-180
MPT-185
MPT-309
MPT-500
MPT-518
MPT-1702
1 2/Unl/P for LO/LO Terminal Tractor applications
Planetary Axles – 1/Unl/P
MOB
MOC
MOD
MOE
MOF
MOG
MOH
MOR
MOS
MOT
MOX
MOY
MOZ
Rear Drive Axles – 1/Unl/P
MT-14X1
RS-23-186
RS-23-380
RS-24-160
RS-30-185
RS-30-380
RT-1451
RT-1601

OFF-HIGHWAY SERVICE

WARRANTY INFORMATION
Coverage under Cummins-Meritor’s warranty require that the application of products be properly approved pursuant to OEM and Cummins-Meritor approvals. Contact Cummins-Meritor regarding specific application approval questions on any product line.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 16 Drivelines – 1/Unl/P

RPL MXL
Transmission – 1/Unl/P&L
FAT 30
Brake Components
Cam 3/Unl/P
Q+ Drum Brake™ 3/Unl/P&L
ASA 3/Unl/P
Hubs/Cast Drums and Other Wheel-End Components 1/Unl/P
Hydraulic Disc Brakes 1/Unl/P
All Other Brakes 1/Unl/P

OFF-HIGHWAY SERVICE

WARRANTY INFORMATION
Transfer Cases – 1/Unl/P
MTC-2212-CV (306)
MTC-3106-FV (TC-137)
MTC-3111 (T-2111 through-shaft)
MTC-3112-CV (548C)
MTC-3116 (T-2111)
MTC-3118-FV (TC-180 and TC-180-23)
MTC-3118-CV (358)
MTC-3120-FV (TC-143)
MTC-3124 (T-2119)
MTC-3206-FV (TC-237)
MTC-3208-GV (RTC-50)
MTC-3209-GV (MTC-60/RTC-60)
MTC-3220-FC (TC-142)
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 17 Coverage Exclusions
Product Description
All
The cost of any repairs, replacements or adjustments to a covered component (1) associated with noise; (2) resulting from the use or installation of non-genuine Cummins-Meritor components or materials; (3) due to vibration associated with improper operation or misapplication of drivetrain components; and (4) damage resulting from corrosion.

For axle assemblies supplied by Cummins-Meritor with suspension and interface brackets designed and/or attached by nonCummins-Meritor parties, Cummins-Meritor warranty coverage does not apply to the brackets, bracket attachment methods and field issues caused by brackets or bracket attachments to any covered component unless specified in a separate OEM agreement.

Front Axles1
Linehaul – King Pin Bushings 1yr/Unl P&L
All Other Vocations – King Pin Bushings Excluded
1 King Pin Bushing wear excluded for all vocations.

Rear Axles
Self-contained traction equalizers and oil filters. The use of NoSPIN differentials will result in the exclusion of axle shafts from warranty considerations. NoSPIN is a product of Eaton.

ASA
Boot and bushing. Bent, broken, over-torqued, missing or otherwise damaged pawl assemblies.

Cam Brake
Brake lining wear and brake shoe “rust-jacking.”
Disc Brake
Pad wear, rotor wear.

Coverage Limitations
Product Description
All
Any claim beyond 60 days from date of repair will not be accepted or honored under this warranty program. Products purchased on an incomplete vehicle (glider) are limited to one year, unlimited miles parts only (1/Unl/P).

Warranty coverage on vehicles with 1,850 lb-ft engine torque and over may be reduced on individual drivetrain components. Contact your Cummins-Meritor representative for specific details.

Front Axles
Tie rod and tie rod ends limited to 3-year/300,000-mile or published vocational coverage, whichever is less. Wheel seals, gaskets and wheel bearings are covered for 1 year/unlimited miles if the wheel end equipment is supplied and assembled by Cummins-Meritor.

Rear Axles
Pinion and through shaft seals limited to 3-year/300,000-mile or published vocational coverage, whichever is less, if yoke is installed by Cummins-Meritor. If yoke is not installed by CumminsMeritor, then Cummins-Meritor does not warrant pinion seals.

Wheel seals, gaskets and wheel bearings are covered for 1 year/unlimited miles if the wheel end equipment is supplied and assembled by Cummins-Meritor.

Rear Axles
The Cummins-Meritor breather part number A-2297-C-8765 with A-3196-J-1336 hose must be used for eligibility of any potential warranty consideration relating to contamination and/or loss of lube in axles.

Cam Brake
Limited to bracket, brake spider and camshaft structural integrity.

STEELite X30
Wearable life is up to the discard diameter of the drum.

Terms and Conditions
(1) What is Covered by this Commercial Warranty?
Meritor Heavy Vehicle Systems, LLC warrants to the owner (“Owner”) that the components listed in this publication, which have been installed by an Original Equipment Manufacturer (“OEM”) as original equipment in vehicles licensed for on-highway use, will be free from defects in material and workmanship. This warranty coverage begins only after the expiration of the OEM’s vehicle warranty for the applicable covered components. Warranty coverage ends at the expiration of the applicable time period from the date of vehicle purchase by the first Owner or the applicable mileage limitation, whichever occurs first. Duration of coverage varies by component and vocation as detailed elsewhere in this warranty statement.

Some components are warranted for parts only and the Owner must pay any labor costs associated with the repair or replacement of the component.

Other components are warranted for both parts and reasonable labor to repair or replace the subject component. Components (whether new, used or remanufactured) installed as replacements under this warranty are warranted only for the remainder of the original period of time or mileage under the original warranty.

For certain components, coverage requires the use of specific extended drain interval or synthetic lubricants. For further information about lubrication and maintenance, see Cummins-Meritor publication Maintenance Manual Number l and the applicable Cummins-Meritor maintenance manual for the product in question. Other conditions and limitations applicable to this warranty are detailed below.

TERMS AND CONDITIONS
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 Product models, brands, names and trademarks depicted herein are the property of their respective owners and, except where otherwise indicated, are not in any way associated with Meritor Heavy Vehicle Systems, LLC, or any parent or affiliate, thereof. (2) Designation of Vocational Use Required
To obtain warranty coverage, each Owner must notify Cummins-Meritor through the OEM new truck and/or trailer dealer of the intended vocational use of the vehicle into which the Cummins-Meritor components have been incorporated prior to the vehicle in-service date. This notification may be accomplished by registering the vehicle through your OEM new truck and/or trailer dealer or with Cummins-Meritor directly. Failure to notify CumminsMeritor of (I) the intended vocational use of the vehicle or (II) a change in vocational use from that which was originally designated, will result in the application of a one year, unlimited mileage, parts only warranty (1/Unl/P) from the initial in-service date.

A second Owner and each subsequent Owner must also notify CumminsMeritor as to the intended vocational use of the vehicle. This notification can be sent directly to Cummins-Meritor or through the OEM new truck and/ or trailer dealer. The duration and mileage coverage of this warranty cannot exceed the coverage extended to the first Owner after his or her initial designation of vocational use.

Coverage under Cummins-Meritor’s warranty requires that the application of products be properly approved pursuant to OEM and Cummins-Meritor approvals. Refer to TP-9441 for axles, SP-8320 for trailer axles, TP-12126 for drivelines and/or contact Cummins-Meritor regarding specific application approval questions on any product line.
(3) What is the Cost of this Warranty?
There is no charge to the Owner for this warranty.
(4) What is not Covered by this Warranty?
This warranty does not cover normal wear and tear; nor does it cover a component that fails, malfunctions or is damaged as a result of (I) improper installation, adjustment, repair or modification (including the use of unauthorized attachments or changes or modification in the vehicle’s configuration, usage or vocation from that which was originally approved by Cummins-Meritor), (II) accident, natural disaster, abuse or improper use (including loading beyond the specified maximum vehicle weight or altering engine power settings to exceed the axle and/or driveline capacity) or (III) improper or insufficient maintenance (including deviation from approved lubricants, change intervals or lube levels). This warranty does not cover any component or part that is not branded by Cummins-Meritor. For vehicles that operate full or part time outside of the United States and Canada, a one year, unlimited mileage, parts only warranty (1/Unl/P) will apply.
(5) Remedy
The exclusive remedy under this warranty shall be the repair or replacement of the defective component at Cummins-Meritor’s option. Cummins-Meritor reserves the right to require that all applicable failed materials are available and/or returned to Cummins-Meritor for review and evaluation. (6) Disclaimer of Warranty

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES

OR CONDITIONS, EXPRESSED, IMPLIED OR STATUTORY INCLUDING

ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
PARTICULAR PURPOSE.
(7) Limitation of Remedies
In no event shall Cummins-Meritor be liable for special, incidental, indirect or consequential damages of any kind or under any legal theory, including, but not limited to, towing, downtime, lost productivity, cargo damage, taxes or any other losses or costs resulting from a defective covered component. (8) To Obtain Service
If the Owner discovers within the applicable coverage period a defect in material or workmanship, the Owner must promptly give notice to either Cummins-Meritor or the dealer from which the vehicle was purchased. To obtain service, the vehicle must be taken to any participating OEM new truck and/or trailer dealer or authorized Cummins-Meritor service location. The dealer will inspect the vehicle and contact Cummins-Meritor for an evaluation of the claim. When authorized by Cummins-Meritor, the dealer will repair or replace during the term of this warranty any defective Cummins-Meritor component covered by this warranty.
(9) Entire Agreement
This is the entire agreement between Cummins-Meritor and the Owner about warranty and no Cummins-Meritor employee or dealer is authorized to make any additional warranty on behalf of Cummins-Meritor. This agreement allocates the responsibilities for component failure between Cummins-Meritor and the Owner.

TERMS AND CONDITIONS
Cummins Inc.

Box 3005
Columbus, IN 47202-3005
U.S.A.
cummins.com
SP-95155
Bulletin 6451105 Produced in U.S.A. Rev. 1/24
©2024 Meritor, Inc.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 )LUHDQG5HVFXH$SSDUDWXV
Coverage:
7KUHH

<HDU0DWHULDODQG:RUNPDQVKLS
0HULWRU:DEFR$%6%UDNH6\VWHP
Limited Warranty
Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

The Meritor Wabco ABS brake system shall be covered by
Meritor Wabco as indicated in the attached Meritor Wabco warranty coverage description
/,0,7(':$55$17<
(b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce.

Three (3) Year Warranty Period
Ends After:

The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

The exclusions listed in the attached Meritor Wabco warranty description shall apply.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4
(;&/86,212)&216(48(17,$/$1',1&,'(17$/'$0$*(6
Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE
POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.

Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.
%8<(5
6(;&/86,9(5(0('<
Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 2/25/2013 WA0232
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES

ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.
',6&/$,0(562):$55$17,(6
capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67

WARRANTY
Warranty coverage is essential to protecting your investment. But understanding the full details of your coverage can be challenging. This straightforward approach allows you, our valued customer, to better understand how your specific vehicle applications will be covered in your region. Our component warranty coverage is provided according to vocation/usage categories listed below. • Linehaul covers high mileage operation (over 60,000 miles/year) on well-maintained major highways of concrete or asphalt construction.
• General Service covers moderate mileage operations (less than 60,000 miles/year) on well-maintained public roads (less than 10 percent off-road) typically with less than three (3) stops per mile. • Heavy Service (Vocational) covers vehicles with more than 10 percent off-road OR moderate to frequent starts/stops typically with more than three (3) stops per mile.
• Off-Highway Service covers lower mileage operations. Vehicles are not typically licensed for highway use. • The standard aftermarket warranty for WABCO products - including WABCO Original parts, WABCO Reman Solutions, ProVia quality aftermarket parts and WABCO retrofit solutions - is one year, parts only from in-service date when purchased from ZF distributor networks or its affiliates and/or subsidiaries.

MODEL YEAR 2021 VEHICLES
How to Read Warranty Coverage (Example)
Number of Years Mileage (in thousands) Unl=Unlimited P=Parts Only P&L=Parts & Labor 3 300 P
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 WARRANTY - MODEL YEAR 2021 VEHICLES
¹ ZF and WABCO branded components. 2
WABCO compressors installed on Cummins, Mercedes, and DDC engines are not warranted or serviced by ZF. Please contact your respective dealer/distributor of those engines for warranty and servicing. 3 An extended warranty of 4/400/P will apply when a WABCO Trailer Control Line Filter is used in combination with a WABCO Trailer ABS valve.
• Aerial Ladder Truck
• Aerial Platform
• Ambulance
• Auto Hauler
• Beverage Truck
• Bulk Hauler
• Chip Hauler (Truck)
• Cross Country Coach
• Doubles
• Flatbed
• Front Engine Commercial
Chassis
• Front Engine Integral
Coach
• General Freight
• Grain Hauler
• Intercity Coach
• Intermodal Chassis
• Livestock Hauler
• Meat Packer
• Moving Van
• Municipal Truck
• Pipe Hauler
• Platform Auto Hauler
• Pumper
• Rear Engine Integral Coach
• Recreational Vehicles
• Refrigerated Freight
• School Bus
• Stake Truck
• Tanker
• Tanker Truck
• Triples
• Tour Bus
• Wrecker

LINEHAUL/GENERAL SERVICE VEHICLES

LINEHAUL/GENERAL SERVICE WARRANTY INFORMATION

LINEHAUL TYPICALLY IS
• High mileage operation (over 60,000 miles/year)
• Well maintained major highways of concrete or
asphalt construction

GENERAL SERVICE TYPICALLY IS
• Moderate mileage operations (less than 60,000 miles/year) • Well maintained public roads (less than 10% off-road) • Less than three (3) stops per mile
WABCO Components1
Air Management
Air Brake Valves
Trailer Lift Axle Control Valve 1/100/P&L
Trailer Control Line Filter3
Air Compressors (ALL)2 2/200/P&L
Air Dryers (ALL) 3/300/P&L
Aerodynamics
OptiFlow® TrailerSkirt 2/UnU/P
OptiFlow® Trailer Tail and AutoTail 2/UnI/P
Braking Systems
ABS (Anti-Lock Braking System) Air
3/300/P&L
ABS (Anti-Lock Braking System) Hydraulic
Electronic Braking System (EBS)
Electronic Stability Control (ESC)
Roll Stability Control (RSS)
Trailer Roll Stability Support (RSS)
Trailer ABS (Anti-Lock Braking System)3
Driveline Suspension Control
Clutch Controls 2/200/P&L
Leveling Valves
1/100/P&L
OptiRide® Automated Manual Transmission (AMT)
OptiRide® Electronically Controlled Air Suspension
(ECAS) 3/300/P&L
WABCO Components1 (cont.)
Safety
OnGuardACTIVE®
3/300/P&L
OnLane®
OnLaneALERT®
OnSide®
Trailer SafeStart™
Trailer TailGUARD™
Telematics
TrailerCAST™ Telematics Device 3/300/P&L
Wheel End Solutions
EasyFit™ Slack Adjuster 6/600/P
MAXXUS™ Truck Air Disc Brake 5/500/P&L
IVTM - Wheel Module 6/P
IVTM - All Other Products 2/P
Pan 17 and 19 Air Disc Brake 2/Unl/P and
1/Unl/L
Pan 22 Air Disc Brake 5/500/P and 1/L
TRISTOP™ D Actuator w/ IBV or IRB 6/600/P
TRISTOP™ D Actuator 3/300/P
UNISTOP™ Actuator 2/200/P
Trailer MAXX22T™ Air Disc Brake 5/500/P and 1/L
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 1 ZF and WABCO branded components. 2 WABCO compressors installed on Cummins, Mercedes, and DDC engines are not warranted or serviced by ZF. Please contact your respective dealer/distributor of those engines for warranty and servicing. 3 An extended warranty of 4/400/P will apply when a WABCO Trailer Control Line Filter is used in combination with a WABCO Trailer ABS valve.

WABCO Components1
Air Management
Air Brake Valves
1/100/P&L Air Compressors (ALL)2
Air Dryers (ALL)
Trailer Control Line Filter3
Braking Systems
ABS (Anti-Lock Braking System) Air 3/300/P&L
ABS (Anti-Lock Braking System) Hydraulic 2/200/P&L
Electronic Braking System (EBS)
3/300/P&L
Electronic Stability Control (ESC)
Trailer ABS Valve3
Roll Stability Control (RSS)
Trailer Roll Stability Support (RSS)
Driveline Suspension Control
OptiRide® Electronically Controlled Air Suspension
(ECAS) 2/200/P&L
Leveling Valves 1/100/P&L
Clutch Controls 2/200/P&L
Safety
OnGuardACTIVE®
3/300/P&L
OnLane®
OnLaneALERT®
OnSide®
Trailer SafeStart™
Trailer TailGUARD™
Telematics
TrailerCAST™ Telematics Device 3/300/P&L
Wheel End Solutions
EasyFit™ Slack Adjuster 2/200/P
MAXXUS™ Air Disc Brake 1/Unl/P&L
IVTM - Wheel Module 6/P
IVTM - All Other Products 2/P
Pan 22, 19 and 17 Air Disc Brake 1/Unl/P&L
Trailer MAXX22T™ 1/Unl/P&L
TRISTOP™ D Actuator w/ IBV 3/Unl/P
TRISTOP™ D Actuator 2/200/P
UNISTOP™ Actuator 1/100/P
• Airport Rescue Fire (ARF)
• Airport Shuttle
• Asphalt Truck
• Block Truck
• Bottom Dump Trailer
Combination
• Cementing Vehicle
• City Bus
• Commercial Pick-Up
• Concrete Pumper
• Construction Material Hauler
• Crash Fire Rescue (CFR)
• Mixer
• Demolition
• Drill Rig
• Dump
• Emergency Service
• Equipment Hauling
• Flatbed Trailer Hauler
• Flatbed Truck
• Fracturing Truck
• Front Loader
• Geophysical Exploration
• Hopper Trailer Combinations
• Landscaping Truck
• Liquid Waste Hauler
• Log Hauling
• Lowboy
• Michigan Special
Gravel Trains
• Michigan Special
Log Hauler
• Michigan Special
Steel Hauler
• Michigan Special
Waste Vehicle
• Municipal Dump
• Newspaper Delivery
• Package Delivery
• Pick-up and Delivery
• Rapid Intervention
Vehicle (RIV)
• Rear Loader
• Recycling Truck
• Residential Pick-Up/Waste
• Rigging Truck
• Roll-Off
• Scrap Truck
• Semi-End Dump
• Sewer/Septic Vacuum
• Shuttle Bus
• Side Loader
• Snowplow/Snowblower
• Steel Hauling
• Tanker
• Tank Truck
• Tractors with Pole Trailers
• Tractor/Trailer with Jeeps
• Transfer Dump
• Transfer Vehicle
• Transit Bus
• Trolley
• Utility Truck
• Winch Truck

HEAVY SERVICE VEHICLES

HEAVY SERVICE (VOCATIONAL) WARRANTY INFORMATION

HEAVY SERVICE TYPICALLY IS
• On/Off road vocations (10% or more off-road) OR
• Moderate to frequent starts/stops typically more than three (3) stops per mile
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 WARRANTY - MODEL YEAR 2021 VEHICLES

INDUSTRIAL AND OFF-HIGHWAY SERVICE

TYPICALLY IS
• Low mileage operation3
• Vehicles are not typically licensed for highway use
¹ ZF and WABCO branded components. 2 WABCO compressors installed on Cummins, Mercedes, and DDC engines are not warranted or serviced by ZF. Please contact your respective dealer/distributor of those engines for warranty and servicing. 3 Equivalent hours of service limit: 2,000 hours for all components.

INDUSTRIAL/OFF-HIGHWAY SERVICE WARRANTY INFORMATION
WABCO Components1
Air Management
Air Brake Valves
Air Compressors (ALL)2 2/Unl/P
Air Dryers (ALL)
Brake Actuation
Air/Hydraulic Actuators
2/Unl/P
Master Cylinders
Remote Actuators
Slave and Wheel Cylinders
Two Fluid Actuators
Brake Locks
Brake Locks (ALL)
Electric Brake Locks 2/Unl/P
Lever Locks
Braking Systems
ABS (Anti-Lock Braking System) Air 1/100/P&L
ABS (Anti-Lock Braking System) Hydraulic
Driveline Suspension Control
Clutch Controls
1/100/P&L
Leveling Valves
Electrohydraulics & Controls
Electronic Pedals
Electrohydraulic Brake Valves (EBV) 2/Unl/P
Pressure Switches
Hydraulic Braking Solutions
Accumulator Charging Valves
Hydraulic Throttle Controls and Switches 2/Unl/P
Modulating Brake Valves
Wheel End Solutions
EasyFit™ Slack Adjuster 2/200/P
Caliper Disc Brakes 2/Unl/P
MAXXUS™ Air Disc Brake 1/Unl/P&L
Multiple Disc Brakes 2/Unl/P
IVTM - Wheel Module 6/P
IVTM - All Other Products 2/P
Pan 22, 19 and 17 Air Disc Brake 1/Unl/P&L
TRISTOP™ D Actuator w/ IBV 3/Unl/P
TRISTOP™ D Actuator 2/200/P
UNISTOP™ Actuator 1/100/P
Market Common Application Types
Agriculture
Fertilizer Spreader, Tractor, Heavy Duty Ag
Trailers, Harvester, Sprayer, Skid Loader, Silage
Bagger, Slurry Wagons, Grain Cart
Airport Support
Pushback Tractor, Towing Tugs, Aircraft Tow
Tractor, Refueling Trucks, Food Service Trucks,
Baggage Tractors, De-Icing Equipment,
Runway Clearing Equipment
Construction
All-Terrain Crane, Rough Terrain Crane,
Excavator, Compactor, Wheel Loader, Road
Roller, Motor Grader, Articulated Dump Truck,
Rubber Tire Road Roller, Backhoe Loaders,
Haul Trucks, Scraper Rough Terrain Forklifts,
Trenchers, Drills
Forestry Logging Forwarder, Kidder, Loaders, Yard
Forklifts, Harvesters Fellers
Material Handling
Port Tractor, Rail Yard Spotter, Stevedoring
Tractor, Trailer Spotter, Yard Jockey, Scissor
Lift, Straddle Carrier, Manlift, Forklift, Boom Lift
Telebandlers, Aerial Work Platforms
Mining
Specialized Mining, Excavator, Haul Truck,
Underground Loader, Service Trucks, Wheel
Loaders, Scrapers, Load Haul Dumps,
Personnel Transports, Bolters, Scalers
Municipal
Street Sweeper, Utility Tractor, Utility Trucks,
Tree Trimmers, Dump Trucks, Tow Trucks, Flat
Bed Trucks, Winch Applications
Oil & Gas
Fracturing Trailer, Injecter Heads, Top Drives,
Jack/Lift Boats, Wireline Trucks, Load-On /
Load-Off
Rail
Railcar Mover, Track Layers, Grinders, Platform
Crane, Locomotive Railcars, Ballast Equipment,
Winch Applications
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67

ABS, ELECTRONIC STABILITY CONTROL (ESC),
ROLL STABILITY CONTROL (RSC), OPTIRIDE®,
ONGUARD® AND ONLANE®, COLLECTIVELY
“ELECTRONICS”
Failure of electronic components due to overvoltage
condition, improper grounding, electrostatic discharge
(ESD), improper shielding, electromagnetic interference (EMI), or other wiring or installation issues. Malfunctions and failure codes caused by other electronic subsystem failures (data bus, engine, transmission, dashboard, etc.)

HYDRAULIC COMPONENTS
For certain components, brake fluid DOT3 or DOT4 is
used as the operating medium. Use of any other fluid will void all warranties associated with that component. For hydraulic braking applications the brake fluid is considered a maintenance item. Maintenance intervals are listed in TB1367.

COVERAGE LIMITATIONS

PRODUCT DESCRIPTION

ALL PRODUCTS
Any claim beyond 60 days from date of repair will not be accepted or honored under this warranty program.

Products purchased on an incomplete vehicle (glider) are limited to one year, 1/Unl/P.

For vehicles that operate full- or part-time outside of the United States and Canada, a 1-Year/Unlimited Miles parts only (1/Unl/P) will apply.

TOOLBOX PLUS™ DIAGNOSTIC SOFTWARE
Proper diagnostics of WABCO Electronics may require the latest version of TOOLBOX PLUS™. Additional labor due
to use of an outdated version of TOOLBOX™ software
and/or the time to purchase or install the latest version of TOOLBOX PLUS™ are not covered under product
warranty.

TERMS AND CONDITIONS

COVERAGE EXCLUSIONS

PRODUCT DESCRIPTION

ALL PRODUCTS
This Warranty shall not apply to the following, but not limited to: (1) damage to the product or its component
parts caused by incorrect use, installation, maintenance or repair, including without limitation (a) improper fit of mating components or brackets, damaged threads, cut, broken,
chafed, pinched or otherwise damaged wiring (sensors,
harnesses and connectors), (b) sensors damaged during
removal when seized in block, or associated with sensor adjustments/ alignments, and (c) damage resulting from the use or installation of non-genuine WABCO components or
materials; (2) damage to the product, its component parts, or diminished product or component part performance due to incorrect operation, deviation from approved conditions or misapplication; (3) any unauthorized disassembly of the product or its component parts including without limitation (a) obliterated, defaced or missing WABCO or WABCO
name plate, serial numbers or label identifying the device as a ZF product or WABCO component, (b) changes to sealed
adjusting screws, and (c) opening or attempted repair of non-serviceable components; (4) malfunction
of the component due to internal contamination of the
vehicle system including without limitation (a) water and other contamination damage that is due to the use of a
non-genuine air dryer cartridge or (b) valve failures due to contamination in air system, (5) complaints associated
with noise, (6) damage resulting from corrosion (including oxidation of electrical devices and connections).

AIR DRYERS
Mounting brackets (see vehicle OEM). Desiccant cartridge housing only.

AIR SYSTEM COMPONENTS
Normal wear items; Gladhand seals, dash valve knobs,
valve actuation handles, treadles, pedals.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 WARRANTY - MODEL YEAR 2021 VEHICLES
(1) What is Covered by this Commercial Warranty?
ZF CV Systems North America LLC and its North American
subsidiaries and affiliates (ZF) warrant to the owner (“Owner”) that the components listed in this publication, which have been installed by an Original Equipment Manufacturer (“OEM”) as original equipment will be free from defects in material and workmanship. This warranty coverage begins from the original in-service date to the limits provided and runs concurrently with any warranties provided by OEMs and/or any distribution agreements and/or any service contracts that cover the components listed in this publication, if any. If the components listed in this publication are covered by an OEM warranty and/or service contract, then the OEM’s warranty and/ or service contract shall supersede ZF’s warranty and Owner shall comply with all OEM’s warranty and/or service contract requirements for claims under such OEM’s warranty and/or service contract until those agreements expire.

Once those agreements expire and provided the ZF warranty has not expired under the terms stated above, the ZF warranty will be in effect until its expiration date.

Warranty coverage ends at the expiration of the applicable time period from the date of vehicle purchase by the first Owner, or, the applicable mileage limitation, whichever occurs first. Duration of coverage varies by component and vocation as detailed previously in this publication.

Some components are warranted for parts only and the Owner must pay any labor costs associated with the repair or replacement of the component. Other components are warranted for both parts and reasonable labor to repair or replace the subject component.

Additional diagnostic time due to use of an outdated version of TOOLBOX™, time to purchase or install latest version of TOOLBOX™ are the responsibility of the authorized ZF distributor networks and are not covered under product warranty. Components installed as replacements under this warranty are warranted only for the remainder of the original period of time or mileage under the original warranty. (2) Designation of Vocational Use Required. To obtain warranty coverage, each Owner must notify ZF through the OEM new truck and/or trailer dealer of the intended vocational use of the vehicle into which the WABCO components have been incorporated prior to the vehicle inservice date. This notification may be accomplished by registering the vehicle through your OEM new truck and/or trailer dealer or with ZF directly. Failure to notify ZF of (I) the intended vocational use of the vehicle or (II) a change in vocational use from that which was originally designated, will result in the application of a one year, unlimited mileage, parts only warranty (1/Unl/P) from the initial inservice date. A second Owner and each subsequent Owner must also notify ZF as to the intended vocational use of the vehicle. This notification can be sent directly to ZF or through
the OEM new truck and/or trailer dealer. The duration and mileage coverage of this warranty cannot exceed the coverage extended to the first Owner after his or her initial designation of vocational use. Coverage under ZF’s warranty requires that the application of products be properly approved pursuant to OEM and ZF, approvals. (3) What is the Cost of this Warranty? There is no charge to the Owner for this warranty.
(4) What is not Covered by this Warranty? In addition to the items listed on "Coverage Exclusions," this warranty does not cover normal wear and tear, or service items; nor does it cover a component that fails, malfunctions or is damaged as a result of (a) improper handling, storage, installation, adjustment, repair or modification including the use of unauthorized attachments or changes or modification in the vehicle’s configuration, usage, or vocation from that which was originally approved by ZF, (b) accident, fire or other casualty, natural disaster, road debris, negligence, misuse, abuse, or improper use (including loading beyond the specified maximum vehicle weight or altering engine power settings to exceed the brake system capacity), or (c) improper or insufficient maintenance (including deviation from maintenance intervals, approved lubricants, or lube levels). This warranty does not cover any component or part that is not sold by ZF. (5) To obtain service. If the owner discovers within the applicable coverage period a defect in material or workmanship, the Owner must promptly give notice to either ZF or the dealer from which the vehicle was purchased. To obtain service, the vehicle must be taken to any participating OEM dealer or ZF distributor networks' servicer. The dealer or ZF authorized servicer will inspect the vehicle and contact ZF for an evaluation of the claim. When authorized by ZF, the dealer or ZF authorized servicer will repair or replace during the term of this warranty any defective WABCO component covered by this warranty. (6) Disclaimer of Warranty and Limitation of remedies. TO THE MAXIMUM

EXTENT PERMITTED BY LAW, THE LIMITED WARRANTY SET

FORTH HEREIN IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER

WARRANTIES, EXPRESS OR IMPLIED, ARISING BY OPERATION OF

LAW OR OTHERWISE, INCLUDING, WITHOUT LIMITATION, ANY

IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE AND/OR WARRANTY FOR HIDDEN OR

LATENT DEFECTS, AND IN NO EVENT WILL ZF OR ANY OF ITS

AFFILIATES BE LIABLE FOR DIRECT, INDIRECT, INCIDENTAL,

PROGRESSIVE, SPECIAL, OR CONSEQUENTIAL DAMAGES OF ANY
KIND.

TERMS AND CONDITIONS
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 (7) Legal action. Any legal action or claim arising from or related to this Warranty, in contract or otherwise, must be commenced within one year from the accrual of that cause of action, or be barred forever. Any dispute arising in connection with this agreement shall be governed by and construed according to the laws of the State of Michigan and be brought, heard and determined exclusively in either the Circuit Court for the County of Oakland, State of Michigan or the United States District Court for the Eastern District of Michigan. The parties stipulate that the referenced venues are convenient.
(8) Remedy. The exclusive remedy under this warranty shall be the repair or replacement of the defective component at ZF's option. ZF reserves the right to require that all applicable covered components are available and/or returned to ZF for review
and evaluation. THE MAXIMUM LIABILITY, IF ANY, OF ZF FOR ALL

DAMAGES, INCLUDING WITHOUT LIMITATION CONTRACT

DAMAGES, BREACH OF WARRANTY, NEGLIGENCE, STRICT

LIABILITY, OR OTHER TORT, IS LIMITED TO AN AMOUNT NOT TO EXCEED THE PURCHASE PRICE OF THE PRODUCT and where
indicated in the product and application warranty information above, the inclusion of labor is limited to the standard repair time. THE

PARTIES ACKNOWLEDGE AND AGREE THAT THE LIMITATION

OF DAMAGES PROVISION SET FORTH IN THIS PARAGRAPH

SURVIVES BETWEEN THE ORIGINAL END USER AND ZF EVEN IF

THE EXCLUSIVE REMEDY SET FORTH ABOVE IS DEEMED TO FAIL
OF ITS ESSENTIAL PURPOSE. ZF may change the design or make improvements to its Products without incurring any warranty obligation for previously manufactured Product .
(9) Entire Agreement. This is the entire agreement between ZF and the Owner about warranty and no, ZF employee, or dealer is authorized to make any additional warranty on behalf of ZF unless in writing and signed by an authorized representative of ZF.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 About ZF Friedrichshafen AG
ZF is a global technology company and supplies systems for passenger cars, commercial vehicles and industrial technology, enabling the next generation of mobility. ZF allows vehicles to see, think and act. In the four technology domains Vehicle Motion Control, Integrated Safety, Automated Driving, and Electric Mobility, ZF offers comprehensive solutions for established vehicle manufacturers and newly emerging transport and mobility service providers. ZF electrifies different kinds of vehicles. With its products, the company contributes to reducing emissions and protecting the climate.

ZF, which acquired WABCO Holdings Inc. on May 29, 2020, now has 160,000 employees worldwide with approximately 260 locations in 41 countries. In 2019, the two then-independent companies achieved sales of €36.5 billion (ZF) and $3.4 billion (WABCO). For more information, visit: www.wabco-na.com
© 2021 ZF CV Systems North America LLC - All rights reserved - SP1375 / 2.2021 For further product details contact your distributor or the WABCO Customer Care Center at 855-228-3203.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 2/8/2010 WA0012

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.

This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This warranty applies only to the cab tubular support and mounting structures and other structural components of the cab of the vehicle model, as identified in the Pierce
specifications for the Fire and Rescue Apparatus.

This warranty does not apply to damage caused by corrosion.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4
Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

Fire and Rescue Apparatus
Coverage:

Ten (10) Year Structural Integrity
Custom Cab
Ten (10) Years
- or -
100,000 Miles
Warranty Period
Ends After:

The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:

The Pierce Custom Cab shall be free from structural failures caused by defects in material and workmanship
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.

Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.

3. BUYER'S EXCLUSIVE REMEDY.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.

Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.

3. BUYER'S EXCLUSIVE REMEDY.

Fire and Rescue Apparatus
Coverage:

Ten (10) Year Pro-Rated Paint and Corrosion
Cab
Ten (10) Years Warranty Period
Ends After:

The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:

Exterior surfaces of the cab painted by Pierce shall be free from blistering, peeling, corrosion or any other adhesion defect caused by defective manufacturing methods or paint material selection.
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 2/8/2010 WA0055

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.

This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This limited warranty is applicable to the vehicle in the following percentage costs of warranty repair, if any:

Topcoat Durability & Appearance: Gloss, Color Retention & Cracking
0-72 months 100%
73-96 months 50%
97-120 months 25%
Integrity of Coating System: Adhesion, Blistering/Bubbling 0-36 months 100%
37-84 months 50%
85-120 months 25%
Corrosion: Dissimilar Metal and Crevice
0-36 months 100%
37-48 months 50%
49-72 months 25%
73-120 months 10%
Corrosion Perforation
0-120 months 100%
This limited warranty applies only to exterior paint. Paint on the vehicle's interior is warranted only under the Pierce Basic One Year Limited Warranty.

Items not covered by this warranty include:
(a) Damage from lack of maintenance and cleaning (proper cleaning and maintenance procedures are detailed in the Pierce operation and maintenance manual).
(b) UV paint fade.
(c) Any cab not manufactured by Pierce.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4
DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 2/8/2010 WA0014

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.

This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This limited warranty applies to all of the control modules for the Command Zone system, including the full color graphic displays. Related wire harnesses, cables and connectors are not covered under this limited warranty and are instead covered under the Pierce One Year Basic Apparatus Limited Warranty.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4
Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

Fire and Rescue Apparatus
Coverage:

Five (5) Year Material and Workmanship
Command Zone Electronics
Five (5) Years Warranty Period
Ends After:

The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:

Command Zone control modules shall be free from failures caused by defects in material and workmanship
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.

Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.

3. BUYER'S EXCLUSIVE REMEDY.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67 Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 1/11/2011 WA0188

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.

This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This limited warranty does not apply to related wire
harnesses, cables, and connectors, which are covered by the Pierce one (1) year basic apparatus limited warranty.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4
Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

Fire and Rescue Apparatus
Coverage:
54 Months Material and Workmanship
Camera System
Fifty - Four (54) months Warranty Period
Ends After:

Warranty Begins: The date of delivery.

This limited warranty covers repairs to correct any defect related to materials or workmanship of the Sharpvision
camera system installed on the apparatus occuring during the warranty period.
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.

Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.

3. BUYER'S EXCLUSIVE REMEDY.

DocuSign Envelope ID: 2876A489-3607-49CB-849A-7754D02FCD67

NEW PRODUCT WARRANTY

PARTICIPATING OEM SALES

DISTRIBUTOR SALES

LIMITED WARRANTY ON NEW ALLISON AUTOMATIC TRANSMISSIONS

USED IN EMERGENCY VEHICLE APPLICATIONS
Allison Transmission will provide for repairs or replacement, at its option, during the warranty period of each new Allison transmission listed below that is installed in an Emergency Vehicle in accordance with the following terms, conditions, and limitations.

WHAT IS COVERED
 WARRANTY APPLIES — This warranty is for new Allison transmission models listed below installed in an Emergency Vehicle and is provided to the original and any subsequent owner(s) of the vehicle during the warranty period.  REPAIRS COVERED — The warranty covers repairs or replacement, at Allison Transmission’s option, to correct any transmission malfunction resulting from defects in material or workmanship occurring during the warranty period. Needed repairs or replacements will be performed using the method Allison Transmission determines most appropriate under the circumstances.  TOWING — Towing is covered to the nearest Allison Transmission Distributor or authorized Dealer only when necessary to prevent further damage to your transmission.
 PAYMENT TERMS — Warranty repairs, including parts and labor, will be covered per the schedule shown in the chart contained in section “APPLICABLE MODELS, WARRANTY LIMITATIONS, AND ADJUSTMENT SCHEDULE.”  OBTAINING REPAIRS — To obtain warranty repairs, take the vehicle to any Allison Transmission Distributor or authorized Dealer within a reasonable amount of time and request the needed repairs. A reasonable amount of time must be allowed for the Distributor or Dealer to perform necessary repairs.
 TRANSMISSION REMOVAL AND REINSTALLATION — Labor costs for the removal and re-installation of the transmission, when necessary to make a warranty repair, are covered by this warranty.  WARRANTY PERIOD — The warranty period for all coverages shall begin on the date the transmission is delivered to the first retail purchaser, with the following exception:

Demonstration Service - A transmission in a new truck or bus may be demonstrated to a total of 5000 miles (8000 kilometers).

If the vehicle is within this limit when sold to a retail purchaser, the warranty start date is the date of purchase. Normal warranty services are applicable to the demonstrating Dealer. Should the truck or bus be sold to a retail purchaser after these limits are reached, the warranty period will begin on the date the vehicle was first placed in demonstration service and the purchaser will be entitled to the remaining warranty.

APPLICABLE MODELS, WARRANTY LIMITATIONS, AND ADJUSTMENT SCHEDULE

WARRANTY LIMITATIONS
(Whichever occurs first)

ADJUSTMENT CHARGE TO BE

APPLICABLE PAID BY THE CUSTOMER
MODELS
Months
Transmission Miles
Or Kilometers Parts Labor
MT, MD
3000, 3200, 3500, 3700 0–24 No Limit No Charge No Charge HT with Hydraulic Controls 0–24 No Limit No Charge No Charge AT, 1000 Series, 2000 Series,
2400 Series 0–36 No Limit No Charge No Charge
HT with Electronic Controls 0–60 No Limit No Charge No Charge HD
1000 EVS, 2100 EVS, 2200 EVS
2350 EVS, 2500 EVS, 2550 EVS,
3000 EVS, 3500 EVS, 4000,
4000 EVS, 4500, 4500 EVS, 4700,
4700 EVS, 4800, 4800 EVS
0–60 No Limit No Charge No Charge