This certification is a material representation of fact upon which reliance was placed when this transaction was made or entered into. Submission of this certification is a prerequisite for making or entering into this transaction imposed by section 1352, title 31, U.S. Code. Any person who fails to file the required certification shall be subject to a civil penalty ofnot less than $10,000 and not more than $100,000 for each such failure.
RESTRICTION ON STATE LOBBYING
(applies to subrecipients as well as States)
None of the funds under this program will be used for any activity specifically designed to urge or influence a State or local legislator to favor or oppose the adoption of any specific legislative proposal pending before any State or local legislative body. Such activities include both direct and indirect (e.g., "grassroots") lobbying activities, with one exception. This does not preclude a State official whose salary is supported with NHTSA funds from engaging in direct communications with State or local legislative officials, in accordance with customary State practice, even if such conununications urge legislative officials to favor or oppose the adoption of a specific pending legislative proposal.
CERTIFICATION REGARDING DEBARMENT AND SUSPENSION
(applies to all subrecipients as well as States)
INSTRUCTIONS FOR PRIMARY TIER PARTICIPANT CERTIFICATION (STATES)
1. By signing and submitting this proposal, the prospective primary tier participant is providing the certification set out below and agrees to comply with the requirements of2 CFR parts 180 and 1200.
2. The inability of a person to provide the certification required below will not necessarily result in denial of participation in this covered transaction. The prospective primary tier participant shall submit an explanation of why it cannot provide the certification set out below. The certification or explanation will be considered in connection with the department or agency's determination whether to enter into this transaction. However, failure of the prospective primary tier patiicipant to furnish a certification or an explanation shall disqualify such person from participation in this transaction.
3. The certification in this clause is a material representation of fact upon which reliance was placed when the department or agency determined to enter into this transaction. If it is later determined that the prospective primary tier participant knowingly rendered an erroneous certification, in addition to other remedies available to the Federal Government, the department or agency may terminate this transaction for cause or default or may pursue suspension or debarment.
4. The prospective primary tier participant shall provide immediate written notice to the department or agency to which this proposal is submitted if at any time the prospective primaty tier patiicipant learns its certification was enoneous when submitted or has become erroneous by reason of changed circumstances.
5. The tern1s covered transaction, civil judgment, debarment, suspension, ineligible, participant, person, principal, and voluntarily excluded, as used in this clause, are defined in 2 CFR parts 180 and 1200. You may contact the department or agency to which this proposal is being submitted for assistance in obtaining a copy of those regulations.
6. The prospective primary tier participant agrees by submitting this proposal that, should the proposed covered transaction be entered into, it shall not knowingly enter into any lower tier covered transaction with a person who is proposed for debannent under 48 CFR pati 9, subpart 9.4, debaned, suspended, declared ineligible, or voluntarily excluded from participation in this covered transaction, unless authorized by the department or agency entering into this transaction.
7. The prospective primary tier participant further agrees by submitting this proposal that it will include the clause titled "Instructions for Lower Tier Participant Certification" including the "Certification Regarding Debarment, Suspension, Ineligibility and Voluntary Exclusion-Lower Tier Covered Transaction," provided by the department or agency entering into this covered transaction, without modification, in all lower tier covered transactions and in all solicitations for lower tier covered transactions and will require lower tier participants to comply with 2 CFR parts 180 and 1200.
8. A participant in a covered transaction may rely upon a certification of a prospective participant in a lower tier covered transaction that it is not proposed for debannent under 48 CFR part 9, subpart 9.4, debarred, suspended, ineligible, or voluntarily excluded from the covered transaction, unless it knows that the certification is erroneous. A participant is responsible for ensuring that its principals are not suspended, debarred, or otherwise ineligible to participate in covered transactions. To verify the eligibility of its principals, as well as the eligibility of any prospective lower tier participants, each patiicipant may, but is not required to, check the System for Award Management Exclusions website (https:/lwww.sam.govt).
9. Nothing contained in the foregoing shall be construed to require establishment of a system of records in order to render in good faith the certification required by this clause. The knowledge and information of a participant is not required to exceed that which is nmmally possessed by a prudent person in the ordinary course of business dealings.
10. Except for transactions authorized under paragraph 6 of these instructions, if a participant in a covered transaction knowingly enters into a lower tier covered transaction with a person who is proposed for debarment under 48 CFR part 9, subpart 9.4, suspended, debaned, ineligible, or voluntarily excluded from participation in this transaction, in addition to other remedies available to the Federal Government, the department or agency may terminate the transaction for cause or default.
CERTIFICATION REGARDING DEBARMENT, SUSPENSION, AND OTHER RESPONSIBILITY MATTERS
PRIMARY TIER COVERED TRANSACTIONS
10/3/2023 11 :55:53 AM Page 17 of 22
1. The prospective primary tier participant certifies to the best of its knowledge and belief, that it and its principals:
a. Are not presently debarred, suspended, proposed for debarment, declared ineligible, or voluntarily excluded from participating in covered transactions by any Federal department or agency; b. Have not within a three-year period preceding this proposal been convicted of or had a civil judgment rendered against them for commission of fraud or a criminal offense in connection with obtaining, attempting to obtain, or perfonning a public (Federal, State, or local) transaction or contract under a public transaction; violation of Federal or State antitrust statutes or commission of embezzlement, theft, forgery, bribery, falsification or destruction of records, making false statements, or receiving stolen property; c. Are not presently indicted for or otherwise criminally or civilly charged by a governmental entity (Federal, State, or local) with commission of any of the offenses enumerated in paragraph ( 1 )(b) of this certification; and
d. Have not within a three-year period preceding this application/proposal had one or more public transactions (Federal, State, or local) tenninated for cause or default.
2. Where the prospective prima1y tier participant is unable to certify to any of the Statements in this certification, such prospective participant shall attach an explanation to this proposal.
INSTRUCTIONS FOR LOWER TIER PARTICIPANT CERTIFICATION
1. By signing and submitting this proposal, the prospective lower tier participant is providing the certification set out below and agrees to comply with the requirements of2 CFR parts 180 and 1200.
2. The certification in this clause is a material representation of fact upon which reliance was placed when this transaction was entered into. Ifit is later dete1mined that the prospective lower tier participant knowingly rendered an erroneous certification, in addition to other remedies available to the Federal Government, the department or agency with which this transaction originated may pursue available remedies, including suspension or debatment.
3. The prospective lower tier participant shall provide immediate written notice to the person to which this proposal is submitted if at any time the prospective lower tier participant learns that its certification was erroneous when submitted or has become erroneous by reason of changed circumstances.
4. The terms covered transaction, civil judgment, debarment, suspension, ineligible, participant, person, principal, and voluntarily excluded, as used in this clause, are defined in 2 CFR parts 180 and 1200. You may contact the person to whom this proposal is submitted for assistance in obtaining a copy of those regulations.
5. The prospective lower tier participant agrees by submitting this proposal that, should the proposed covered transaction be entered into, it shall not knowingly enter into any lower tier covered transaction with a person who is proposed for debarment under 48 CFR part 9, subpart 9.4, debarred, suspended, declared ineligible, or voluntarily excluded from participation in this covered transaction, unless authorized by the department or agency with which this transaction originated.
6. The prospective lower tier participant further agrees by submitting this proposal that it will include the clause titled "Instructions for Lower Tier Participant Certification" including the "Certification Regarding Debaiment, Suspension, Ineligibility and Voluntaiy Exclusion-Lower Tier Covered Transaction," without modification, in all lower tier covered transactions and in all solicitations for lower tier covered transactions and will require lower tier participants to comply with 2 CFR parts 180 and 1200.
7. A participant in a covered transaction may rely upon a cettification of a prospective pa1ticipant in a lower tier covered transaction that it is not proposed for deba1ment under 48 CFR part 9, subpart 9.4, debaJTed, suspended, ineligible, or voluntarily excluded from the covered transaction, unless it knows that the certification is erroneous. A participant is responsible for ensuring that its principals are not suspended, debarred, or otherwise ineligible to participate in covered transactions. To verify the eligibility of its principals, as well as the eligibility of any prospective lower tier patticipants, each paiticipant may, but is not required to, check the System for Award Management Exclusions website ( https://www.sam.gov/).
8. Nothing contained in the foregoing shall be construed to require establishment of a system ofrecords in order to render in good faith the certification required by this clause. The knowledge and information of a participant is not required to exceed that which is normally possessed by a prudent person in the ordinary course of business dealings.
9. Except for transactions authorized under paragraph 5 of these instructions, if a participant in a covered transaction knowingly enters into a lower tier covered transaction with a person who is proposed for debarment under 48 CFR part 9, subpatt 9.4, suspended, debarred, ineligible, or voluntarily excluded from patticipation in this transaction, in addition to other remedies available to the Federal Government, the department or agency with which this transaction originated may pursue available remedies, including suspension or debarment.
CERTIFICATION REGARDING DEBARMENT, SUSPENSION, INELIGIBILITY AND VOLUNTARY EXCLUSION
LOWER TIER COVERED TRANSACTIONS
1. The prospective lower tier participant certifies, by submission of this proposal, that neither it nor its principals is presently debarred, suspended, proposed for debarment, declared ineligible, or voluntarily excluded from participating in covered transactions by any Federal department or agency.
10/3/2023 11 :55:53 AM Page 18 of 22
2. Where the prospective lower tier participant is unable to certify to any of the statements in this certification, such prospective participant shall attach an explanation to this proposal.
BUY AMERICA
(applies to subrecipients as well as States)
The State and each subrecipient will comply with the Buy America requirement (23 U.S.C. 313) when purchasing items using Federal funds. Buy America requires a State, or subrecipient, to purchase with Federal funds only steel, iron and manufactured products produced in the United States, unless the Secretaiy of Transportation detemrines that such domestically produced items would be inconsistent with the public interest, that such materials are not reasonably available and of a satisfactory quality, or that inclusion of domestic materials will increase the cost of the overall project contract by more than 25 percent. In order to use Federal funds to purchase foreign produced items, the State must submit a waiver request that provides an adequate basis and justification for approval by the Secretary of Transportation.
CERTIFICATION ON CONFLICT OF INTEREST
(applies to subrecipients as well as States)
GENERAL REQUIREMENTS
No employee, officer, or agent of a State or its subrecipient who is authorized in an official capacity to negotiate, make, accept, or approve, or to take part in negotiating, making, accepting, or approving any subaward, including contracts or subcontracts, in connection with this grant shall have, directly or indirectly, any financial or personal interest in any such subaward. Such a financial or personal interest would arise when the employee, officer, or agent, any member of his or her immediate family, his or her partner, or an organization which employs or is about to employ any of the parties indicated herein, has a financial or personal interest in or a tangible personal benefit from an entity considered for a subaward. Based on this policy:
1. The recipient shall maintain a written code or standards of conduct that provide for disciplinary actions to be applied for violations of such standards by officers, employees, or agents. a. The code or standards shall provide that the recipient's officers, employees, or agents may neither solicit nor accept gratuities, favors, or anything of monetary value from present or potential subawardees, including contractors or parties to subcontracts.
b. The code or standards shall establish penalties, sanctions, or other disciplinary actions for violations, as permitted by State or local law or regulations.
2. The recipient shall maintain responsibility to enforce the requirements of the written code or standards of conduct.
DISCLOSURE REQUIREMENTS
No State or its subrecipient, including its officers, employees, or agents, shall perform or continue to perform under a grant or cooperative agreement, whose objectivity may be impaired because of any related past, present, or currently planned interest, financial or otherwise, in organizations regulated by NHTSA or in organizations whose interests may be substantially affected by NHTSA activities. Based on this policy:
1. The recipient shall disclose any conflict of interest identified as soon as reasonably possible, making an immediate and full disclosure in writing to NHTSA. The disclosure shall include a description of the action which the recipient has taken or proposes to take to avoid or mitigate such conflict.
2. NHTSA will review the disclosure and may require additional relevant information from the recipient. If a conflict of interest is found to exist, NHTSA may (a) terminate the award, or (b) dete11nine that it is otherwise in the best interest of NHTSA to continue the award and include appropriate provisions to mitigate or avoid such conflict.
3. Conflicts of interest that require disclosure include all past, present, or currently planned organizational, financial, contractual, or other interest( s) with an organization regulated by NHTSA or with an organization whose interests may be substantially affected by NHTSA activities, and which are related to this award. The interest( s) that require disclosure include those of any recipient, affiliate, proposed consultant, proposed subcontractor, and key personnel of any of the above. Past interest shall be limited to within one year of the date of award. Key personnel shall include any person owning more than a 20 percent interest in a recipient, and the officers, employees or agents of a recipient who are responsible for making a decision or taking an action under an award where the decision or action can have an economic or other impact on the interests of a regulated or affected organization.
PROHIBITION ON USING GRANT FUNDS TO CHECK FOR HELMET USAGE (applies to all subrecipients as well as States)
The State and each subrecipient will not use 23 U.S.C. Chapter 4 grant funds for programs to check helmet usage or to create checkpoints that specifically target motorcyclists. 10/3/2023 11 :55:53 AM Page 19 of 22
POLICY ON SEATBELT USE
In accordance with Executive Order 13043, Increasing Seat Belt Use in the United States, dated April 16, 1997, the Grantee is encouraged to adopt and enforce on-the-job seat belt use policies and programs for its employees when operating company-owned, rented, or personally-owned vehicles. The National Highway Traffic Safety Administration (NHTSA) is responsible for providing leadership and guidance in support of this Presidential initiative. For information and resources on traffic safety programs and policies for employers, please contact the Network of Employers for Traffic Safety (NETS), a public-private partnership dedicated to improving the traffic safety practices of employers and employees. You can download information on seat belt programs, costs of motor vehicle crashes to employers, and other traffic safety initiatives at www.trafficsafety.org. The NHTSA website (www.nhtsa.gov) also provides information on statistics, campaigns, and program evaluations and references.
POLICY ON BANNING TEXT MESSAGING WHILE DRIVING
In accordance with Executive Order 13513, Federal Leadership On Reducing Text Messaging While Driving, and DOT Order 3902.10, Text Messaging While Driving, States are encouraged to adopt and enforce workplace safety policies to decrease crashes caused by distracted driving, including policies to ban text messaging while driving company owned or rented vehicles, Government-owned, leased or rented vehicles, or privately-owned vehicles when on official Government business or when performing any work on or behalf of the Government. States are also encouraged to conduct workplace safety initiatives in a manner commensurate with the size of the business, such as establishment of new rules and programs or re-evaluation of existing programs to prohibit text messaging while driving, and education, awareness, and other outreach to employees about the safety risks associated with texting while driving. 10/3/2023 11 :55:53 AM Page 20 of 22
State of California -Office of Traffic Safety
OTS-55 Grant Electronic Management System (GEMS) Access Exhibit C
INSTRUCTIONS FOR ADDING OR UPDATING GEMS USERS
1. Each agency is allowed a total of FIVE (5) GEMS Users.
GRANT NUMBER
PT24077
2. GEMS Users listed on this form will be authorized to login to GEMS to complete and submit Quarterly Performance Reports (QPRs) and reimbursement claims.
3. Complete the form if adding, removing or editing a GEMS user(s).
4. The Grant Director must sign this form and return it with the Grant Agreement.
GRANT DETAILS
Grant Number: PT24077
Agency Name: Garden Grove Police Department
Grant Title:
Agreement Total:
Selective Traffic Enforcement Program (STEP)
$370,000.00
Authorizing Official: Lisa L. Kim
Fiscal Official: Patricia Song
Grant Director: John Yergler
I CURRENT GEMS USER(S)
1. Jeremy Morse
Title: Police Officer
Phone: (714) 7 41-5767
Email: [email protected]
2. Selamawit Nigatu
Title: Accountant
Phone: (714) 7 41-5045
Email: [email protected]
3. Royce Wimmer
Title: Sergeant
Phone: (714) 741-5787
Email: [email protected]
4. John Yergler
Title: Police Officer
Phone: (714) 741-5772
Email: [email protected]
10/3/2023 11 :55:53 AM
Media Contact: Yes
Media Contact: No
Media Contact: Yes
Media Contact: Yes
Complete the below information if adding, removing or editing a GEMS user(s) GEMS User 1 Add as a media contact? Yes D No□
Add/Change 0 Remove Access D
Name Job Title
Email address Phone number
GEMS User 2 Add as a media contact? YesO No□
Add/Change 0 Remove Access D
Name Job Title
Email address Phone number
GEMS User 3 Add as a media contact? YesO No□
Add/Change 0 Remove Access D
Name Job Title
Email address Phone number
GEMS User4 Add as a media contact? YesO No□
Add/Change 0 Remove Access D
Name Job Title
Email address Phone number
GEMS User 5 Add as a media contact? Yes D No□
Add/Change 0 Remove Access D
Name Job Title
Email address Phone number
Form completed by: ;,,,,,~'"'""'' Date: Oct 3, 2023
As a signatory I hereby authorize the listed individual(s) to represent and have GEMS user access.
Jol1~~4aron John J. Yergler
Signature Name
Oct 3, 2023 Grant Director
Date Title
10/3/2023 11 :55:53 AM Page 22 of 22
Grant Agreement -PT24077
Final Audit Report
Created:
By:
Status:
Transaction ID:
2023-10-03
Kristen Mickey ([email protected])
Signed
CBJCHBCAABAA 1 dAZmVOA 7K56XPPPi58IyBO0EvXzKECf
"Grant Agreement -PT24077" History
Document created by Kristen Mickey ([email protected]) 2023-10-03 -6:56:09 PM GMT
Document emailed to [email protected] for signature
2023-10-03 -6:56:25 PM GMT
Email viewed by [email protected]
2023-10-03 -7:02:26 PM GMT
Signer [email protected] entered name at signing as John J. Yergler 2023-10-03 -7:46:32 PM GMT
Document e-signed by John J. Yergler [email protected])
2023-10-10
Signature Date: 2023-10-03 -7:46:34 PM GMT-Time Source: server-Signature captured from device with phone number XXXXXXX7002 on
t'RAFF!C
SAH'l'Y
Document emailed to [email protected] for signature
2023-10-03 -7:46:36 PM GMT
Email viewed by [email protected]
2023-10-03 -7:46:57 PM GMT
Signer [email protected] entered name at signing as John J. Yergler 2023-10-03 -7:48:57 PM GMT
Document e-signed by John J. Yergler [email protected])
Signature Date: 2023-10-03 -7:48:59 PM GMT -Time Source: server-Signature captured from device with phone number XXXXXXX7002 Document emailed to [email protected] for signature 2023-10-03 -7:49:01 PM GMT
Email viewed by [email protected]
2023-10-03 -10:14:02 PM GMT
I
Powered by
Adobe
Acrobat Sign
OT$
TRAFFIC
SAH11'Y
Signer [email protected] entered name at signing as Patricia Song 2023-10-04 -8:56:35 PM GMT
Document e-signed by Patricia Song ([email protected]) Signature Date: 2023-10-04 -8:56:37 PM GMT -Time Source: server Document emailed to [email protected] for signature
2023-10-04 -8:56:39 PM GMT
Email viewed by [email protected]
2023-10-04 -9:32:17 PM GMT
Signer [email protected] entered name at signing as Lisa Kim 2023-10-04 -9:32:55 PM GMT
Document e-signed by Lisa Kim ([email protected])
Signature Date: 2023-10-04 -9:32:57 PM GMT -Time Source: server Document emailed to Carolyn Vu ([email protected]) for signature 2023-10-04 -9:32:58 PM GMT
Email viewed by Carolyn Vu ([email protected])
2023-10-04 -9:33:31 PM GMT
Document e-signed by Carolyn Vu ([email protected]) Signature Date: 2023-10-04 -9:33:40 PM GMT -Time Source: server Document emailed to Barbara Rooney ([email protected]) for signature 2023-10-04 -9:33:41 PM GMT
Email viewed by Barbara Rooney ([email protected]) 2023-10-10 -4: 15:42 PM GMT
Document e-signed by Barbara Rooney ([email protected]) Signature Date: 2023-10-10 -4:15:59 PM GMT-Time Source: server Agreement completed.
2023-10-10 -4:15:59 PM GMT
I
Powered by
Adobe
Acrobat Sign
Agenda Item - 4.b.
City of Garden Grove
INTER-DEPARTMENT MEMORANDUM
To: Lisa L. Kim From: Amir El-Farra
Dept.: City Manager Dept.: Police Chief
Subject: Receive and file the 2023
Garden Grove Police
Department Military
Equipment Annual
Report, and Introduce the
first reading of an Ordinance
approving the Military
Equipment Use Policy and
rescinding Ordinance No.
2935
Date: 10/24/2023
OBJECTIVE
For the City Council to receive and file the 2023 Garden Grove Police Department Military Equipment Annual Report, and introduce an Ordinance adopting the Military Equipment Use Policy.
BACKGROUND
Effective January 1, 2022, California Assembly Bill 481 added Chapter 12.8 (commencing with Section 7070) to Division 7 of Title 1 of the Government Code.
These provisions require law enforcement agencies to obtain the approval of their respective governing bodies, by adoption of a military equipment use policy (via ordinance), prior to use of any equipment defined by the Government Code as “military equipment.” Upon approval of an agency’s military equipment use policy, the agency must, thereafter, prepare an annual military equipment use report which must be published to the City’s website as well as hold at least one well publicized and conveniently located community engagement meeting at which the general public may discuss and ask questions regarding the annual military equipment report and the law enforcement agency’s funding, acquisition, and use of military equipment.
The annual report required by Assembly Bill 481 must include a summary of each type of military equipment owned or used by the agency, its intended purpose, how each type of equipment was used by the agency in the preceding year, a summary of any complaints received by the agency concerning the equipment, the results of any internal audits pertaining to violations of the military equipment use policy, the total cost for each type of equipment, and the quantity possessed by the agency.
In addition to the required annual report, AB 481 requires each agency’s governing body to review any ordinance it has approved which adopts a military equipment use policy and to vote on whether to renew the ordinance. The governing body may choose whether to renew the ordinance, disapprove authorization for use of equipment where standards have not been met, or require modifications to the military equipment use policy based on whether the equipment detailed within the annual report complies with policy and meets the standards set forth in California Government Code section 7071(d).
DISCUSSION
On June 14, 2022, the City Council adopted Ordinance No. 2935 approving Garden Grove Police Department General Order 2.29 [Military Equipment]. Pursuant to California Government Code section 7072, the Garden Grove Police Department has prepared an annual report which reflects the following for the preceding calendar year:
1. A summary of how military equipment was used and the purpose of its use;
2. A summary of any complaints or concerns received concerning the military equipment;
3. The results of any internal audits, any information about violations of the military equipment use policy, and any actions taken in response;
4. The total annual cost for each type of military equipment, including acquisition, personnel, training, transportation, maintenance, storage, upgrade, and other ongoing costs, and form what source funds will be provided for the military equipment in the calendar following submission of the annual report;
5. The quantity possessed for each type of military equipment; and
6. If the law enforcement agency intends to acquire additional military equipment in the next year, the quantity sought for each type of military equipment.
A copy of the Garden Grove Police Department’s Annual Military Equipment Use Report for the period from June 2022 to September 2023 is attached hereto as Attachment 1 (hereinafter the “Annual Report”). The Annual Report has been posted on the City’s website, and in accordance with the provisions of AB 481, the Department will publicize and conduct a community engagement meeting regarding the Department’s use of “military equipment” at a date, time and place to be published as appropriate.
On June 14, 2022, the City adopted Ordinance No. 2935 (Attachment 2) which approved the Garden Grove Police Department’s Military Equipment Policy identified as General Order 2.29. Due to the migration of the Police Department’s policies to the Lexipol system, the Department’s Military Equipment Policy will now be identified as Policy No. 706. Apart from the change in numbering and the update of the specific military equipment in possession of the Department for the relevant period, Policy 706 is substantively the same as General Order 2.29; however, because Ordinance No. 2935 specifies approval of Garden Grove Police Department General Order 2.29, an Ordinance is required to be introduced and adopted to reflect Policy No. 706 (Attachment 4). Pursuant to Government Code section 7071, subsection (c), consideration of an ordinance approving a military equipment use policy must take place as an agenda item for an open session of a regular city council meeting which provides an opportunity for public comment. Upon adoption, this ordinance will replace Ordinance No. 2935.
FINANCIAL IMPACT
At this time, there is only minimal financial impact associated with posting the military equipment use policy and Annual Report on the Department’s website and publicizing and holding the required community engagement meeting.
RECOMMENDATION
It is recommended that the City Council:
Receive and file the Garden Grove Police Department Military Equipment Annual Report for the year 2023; and
Introduce the Ordinance adopting the Military Equipment Use Policy and rescinding Ordinance No. 2935.
By: Vince Vaicaro, Lieutenant
ATTACHMENTS:
Description Upload
Date Type File Name
Ordinance
Adopting
Military
Equipment
Use Policy
706
10/14/2023 Ordinance GG_Ordinance_Adopting_the_GGPD_Military_Equipment_Use_Policy_706.DOCX 2023
Annual
Military
Equipment
Use Report
10/13/2023 Backup
Material 2023_Annual_Military_Equipment_Use_Report_(AB_481).DOCX GGPD Policy
706 10/13/2023 Backup
Material GGPD_Policy_706_-_Military_Equipment_2023_Update_(JMM_Revisions).DOCX
•
•
1794435.1
ORDINANCE NO. _____
AN ORDINANCE OF THE CITY COUNCIL OF THE CITY OF GARDEN
GROVE ADOPTING THE GARDEN GROVE POLICE DEPARTMENT
MILITARY EQUIPMENT USE POLICY PURSUANT TO GOVERNMENT
CODE 7071 AND RESCINDING ORDINANCE NO. 2935.
City Attorney Summary
This Or dinance adopts the Garden Grove Police
Department Military Equipment Use Policy pursuant to
Government Code 7071 and replaces Ordinance No.
2935, which provided the initial approval of the
Department’s Military Equipment Use Policy.
WHEREAS, the mission of the Garden Grove Police Department (Department) is to provide the highest quality police services to the communities it serves; and
WHEREAS, the Department values transparency and public input, and welcomes open dialogue about its practices and operations; and
WHEREAS, the preservation and sustainability of public safety, civil rights, and officer safety is paramount; and
WHEREAS, the Department responds to a wide variety of critical incidents, instances of civil unrest, and life and deat h situations, and operates in numerous unpredictable, dynamic environments; and
WHEREAS, a variety of equipment options is needed for safe and effective resolution of those situations; and
WHEREAS, each situation is evaluated by incident commanders or su pervisors who, based on circumstances and Department directives, determine which equipment should be used; and
WHEREAS, the Department’s diverse catalogue of military equipment, as defined in state law, and associated training gives police officers the co nfidence and capability to deescalate volatile situations, enhance the safety of the public and officers, and bring critical incidents to a safe resolution; and
WHEREAS, from time to time, the Department may be asked to assist or need to be assisted by other law enforcement agencies, which may include use of military equipment, as defined in state law; and
WHEREAS, partnerships with other law enforcement agencies are an integral part of maintaining the continuity of public safety within the region; and
Garden Gove City Council
Ordinance No. _____
1794435.1
WHEREAS, Assembly Bill 481 (AB 481) became effective on January 1, 2022; and
WHEREAS, AB 481 defines military equipment in Government Code section 7070(c) to include a wide range of equipment as described in the Department’s Military Equipment Policy 706; and
WHEREAS, AB 481 requires the Department to obtain the approval of the City Council by an ordinance adopting its Policy 706 prior to requesting military equipment from the federal government, seeking funds for military equipment, including grants and donations, acquiring military equipment, collaborating with another law enforcement agency in the use of military equipment in Garden Grove , using any new or existing military equipment in a manner not previously approved by the City Council, or entering into an agreement for funding, receipt, acquisition, use of, or collaboration in the use of military equipment; and
WHEREAS, to promote public safety, civil rights, and officer safety, the Department desires to continue using, seeking funding for, acquiri ng, and collaborating, when necessary, with other law enforcement agencies, in the use of the military equipment described in its Policy 706; and
WHEREAS, on June 14, 2022, the Council adopted Ordinance No. 2935 approving the Department’s initial Military Use Policy which was, at that time, identified as General Order 2.29 and which is substantively the same as Policy 706; and
WHEREAS, the Department has presented its annual report regarding the Department’s use of military equipment to the Council and th e Council finds that the annual report meets the requirements of Government Code section 7072; and
WHEREAS, the Council has examined the Department’s Policy 706 and finds that the Police Department has submitted all information described in Government Code section 7070(d) and 7072(a) , enabling the City Council to make the findings in this ordinance; and
WHEREAS, pursuant to Government Code section 7071(d), the City Council finds that the military equipment described in Policy 706 is necessary because there is no reasonable alternative that can achieve the same objective of officer and civilian safety; and
WHEREAS, pursuant to Government Code section 7071(d), the City Council further finds that Policy 706 will safeguard the public’s welfare, safety, ci vil rights, and civil liberties; and
Garden Gove City Council
Ordinance No. _____
1794435.1
WHEREAS, pursuant to Government Code section 7071(d), the City Council further finds that continued use of existing military equipment and purchase of military equipment described in Policy 706 is reasonably cost effec tive compared to available alternatives that can achieve the same objective of officer and civilian safety; and
WHEREAS, pursuant to Government Code section 7071(d), the City Council further finds that the Department will ensure use of existing military e quipment described in Policy 706 will comply with the policy in the future; and
WHEREAS, the Department’s Policy 706 has been prepared as its proposed military equipment use policy, and it has been published on the Garden Grove Police Department’s internet website since June 2022.
NOW, THEREFORE, THE CITY COUNCIL OF THE CITY OF GARDEN GROVE HEREBY ORDAINS AS FOLLOWS:
SECTION 1: The foregoing recitals are hereby incorporated in full and adopted as the City Council’s findings pertaining to the Garden Grove Police Department’s Military Equipment Use Policy.
SECTION 2 : Based on the above recitals and findings, and the information provided to the City Council at the public meeting, the City Council determines that Policy No. 706 of the Garden Grove Police Department complies with standards for approval under Government Code section 7071:
1. The identified military equipment is necessary because there is no reasonable alternative that can achieve the same objective of officer and civilian safety.
2. Policy No. 706 will safeguard the public’s welfare, safety, civil rights, and civil liberties.
3. The purchase and use of the identified military equipment is reasonably cost effective compared to available alternatives that can achieve the same objective of officer and civilian safety.
4. All military equipment use prior to the adoption of Policy No. 706 complied with applicable Department policy in effect at that time, and adoption of Policy No. 706 will ensure future compliance.
SECTION 3: Garden Grove Police Department Policy No. 706 pertaining Military Equipment, establishing the Department’s Military Equipment Use Policy is hereby approved and adopted.
Garden Gove City Council
Ordinance No. _____
1794435.1
SECTION 4: The City Council approves seeking funds for military equipment described in Policy No. 706 , including grants and donations, acquiring military equipment described in Policy No. 706 , collaborating as needed with another law enforcement agency in the deployment or use of military equipment in Garden Grove or Orange County, using existing military e quipment as described in Policy No. 706 , and soliciting or entering into an agreement for funds, acquisition, use of, or collaboration for use of military equipment described in Policy No. 706.
SECTION 5: That this approval is not intended to and shall not supersede existing procedures to seek approval for the appropriation and expenditure of specific funds through the bi-annual budget process, or existing processes for the approval and execution of contracts, donations, and grants.
SECTION 6: That the City Council shall review this Ordinance annually and vote whether to renew the Ordinance, consistent with the requirements of state law.
SECTION 7: This Ordinance replaces Ordinance No. 2935 and upon its adoption Ordinance No. 2935 is hereby rescinded.
SECTION 8: If any section, subsection, subdivision, sentence, clause, phrase, word, or portion of this Ordinance is, for any reason, held to be invalid or unconstitutional by the decision of any court of competent jurisdiction, such decision shall not affect the validity of the remaining portions of this Ordinance. The City Council hereby declares that it would have adopted this Ordinance and each section, subsection, subdivision, sentence, clause, phrase, word, or portion thereof, irrespective of the fac t that any one or more sections, subsections, subdivisions, sentences, clauses, phrases, words or portions thereof be declared invalid or unconstitutional.
SECTION 9: The Mayor shall sign and the City Clerk shall certify to the passage and adoption of this Ordinance and shall cause the same, or the summary thereof, to be published and posted pursuant to the provisions of law and this Ordinance shall take effect thirty (30) days after adoption.
PASSED AND ADOPTED by the City Council this ____ day of ________, 2023, by the following vote:
AYES:
NOES:
ABSENT:
ABSTAIN:
Mayor
Garden Gove City Council
Ordinance No. _____
1794435.1
ATTEST:
City Clerk
1794440.1
[GGPD LETTER HEAD]
GARDEN GROVE POLICE DEPARTMENT
ANNUAL MILITARY EQUIPMENT USE REPORT
JUNE 2022 – OCTOBER 2023
1. INTRODUCTION
Garden Grove Police Department Policy 706 [Military Equipment] (formerly General Order 2.29) sets forth the standards and procedures applicable to the Garden Grove Police Department’s (“Department”) acquisition and use of “military equipment” as that term is defined by California Government Code section 7070. The policy additionally provides guidelines for the Department’s use of military equipment, a process to receive and evaluate questions, comments, and/or complaints from the public regarding the Department’s use of military equipment, and for the preparation and publication of an annual report regarding the Department’s acquisition and use of military equipment as required by California Government Code section 7072.
The annual report contemplated by Government Code section 7072 (“Annual Report”) must include the following:
a. A summary of how military equipment was used and the purpose of its use; b. A summary of any complaints or concerns received concerning the military equipment; c. The results of any internal audits, any information about violations of the military equipment use policy, and any actions taken in response; d. The total annual cost for each type of military equipment, including acquisition, personnel, training, transportation, maintenance, storage, upgrade, and other ongoing costs, and form what source funds will be provided for t he military equipment in the calendar following submission of the annual report;
e. The quantity possessed for each type of military equipment; and f. If the law enforcement agency intends to acquire additional military equipment in the next year, the quantity sought for each type of military equipment.
This document shall constitute the Department ’s Annual Report on the use of military equipment for the period of June 2022 through October 2023.
2. SUMMARY OF DEPARTMENT’S USE OF MILITARY EQUIPMENT FROM JUNE 2022 THROUGH OCTOBER 2023
The following are summaries for each incident in which a piece of “military equipment” was utilized by the Department for the period of June 2022 through October 2023.
On 1/23/2023, Garden Grove Police Officers responded to a residence regarding a restrained subject forcing his way into the residence. The subject had previously been arrested for being in possession of a firearm and had an outstanding warrant for that charge.
1794440.1
Officers established containment o f the residence and utilized the Lenco Bearcat G2 Armored Rescue Vehicle ( hereinafter “ARV”) to make announcements from the front of the residence. The suspect later exited the residence and was taken into custody. DR 23004503
On 2/14/2023, Garden Grove Police Officers responded to a call for service regarding a violent suspect who had threatened to stab family members. Upon arrival, the suspect barricaded himself in the residence. After the suspect refused to surrender the SWAT team responded. The ARV was used at the location as ballistic protection as negotiators attempted to convince the suspect to surrender. When the suspect refused to communicate with negotiators, chemical agents (CTS CS Baffled Cannister Grenade and Defense Technologies 40MM CS Ferret Liquid Barricade Penetrating Projectile Rounds) were introduced into the residence and the ARV was used to breach the garage door where the suspect was barricaded. The event came to a safe conclusion when the suspec t was later taken into custody. DR 23009194
On 4/1/2023, Garden Grove Police Officers responded to a residence in reference to shots fired at the location. Upon arrival , officers learned a home invasion had occurred during which the suspects forced their way through a back door, fired a shot from a handgun, and demanded money from the occupants of the home. The ARV was used at the location as ballistic protection as officers requested all occupants of the home to exit. Officers eventually discovered that all suspects had fled prior to their arrival. DR 23018306
On 5/23/2023, the Garden Grove Police SWAT team served a search warrant at the property of a suspect involved in a shooting incident which occurred on 4/1/2023. During execution of the search warrant the ARV was used at the location as ballistic protection.
The suspect was safely taken into custody. DR 23018377
The City of Garden Grove hosted its annual Strawberry Festival from May 26 -29, 2023.
The ARV was used at the festival and for the parade at fixed posts for security purposes during the events. There were no security breaches and the ARV remained parked throughout the event.
On 7/4/2023, the Huntington Beach Police Department hosted its annual 4th of July parade.
The ARV was requested for the parade and was used at a fixed post for security purposes during the event. There were no security breaches and the ARV remained parked throughout the event.
On 8/29/2023, Garden Grove Police Officers responded to a residence in reference to a victim being physically assaulted including having a loaded gun pointed at him by the suspect. The suspect barricaded himself in the residence with his elderly disabled mother.
The ARV was used at the location as ballistic protection and to breach the suspect’s bedroom window after he refused to surrender. The suspect exited the home after his window was breached and he was taken into custody. DR 23050049
1794440.1
On 9/1/2023, Garden Grove Police Officers were flagged down near a hotel in reference to a victim being robbed and pistol whipped. During the investigation officers learned the suspect was in a nearby hotel room. The ARV was used at the location as ballistic protection as officers contacted the suspect. The suspect eventually surrendered and was taken into custody. A handgun was later located in the hotel room. DR 23050699
3. SUMMARY OF COMPLAINTS OR CONCERNS EXPRESSED BY CITIZENS
The Department’s website has information regarding how citizens can submit questions, comments, or concerns regarding the Department’s military equipment policy, or use of military equipment by the Department. Additionally, the Department accepts and inves tigates any complaints received regarding the use of military equipment in the same manner that all personnel complaints are received and investigated.
During the period of June 2022 through October 2023, the Department did not receive any complaints or concerns regarding the Department’s military use policy, nor the manner in which Department personnel utilized military equipment.
4. RESULTS OF INTERNAL AUDITS, INFORMATION REGARDING
VIOLATIONS OF MILITARY EQUIPMENT POLICY AND ACTIONS TAKEN IN
RESPONSE
Use of military equipment by Department personnel is monitored by the Department’s designated Military Equipment Coordinator. During the period of June 2022 through October 2023, there were no identified violations of the Department’s military equipment policy.
5. QUANTITY AND ANTICIPATED ANNUAL COST FOR MILITARY
EQUIPMENT
The following list reflects the military equipment in the possession of , or used by the Department, and/or military equipment which the Department anticipates acquiring in the coming year, along with details regarding the anticipated costs associated with acquisition and maintenance of the equipment.
A. RESCUE VEHICLE
Commercially produced wheeled rescue personnel vehicle utilized for law enforcement purposes.
Current Inventory:
LENCO BEARCAT G2
1794440.1
Description: Rescue vehicle that seats 10 -12 personnel with open floor plan that allows for rescue of downed personnel. It can stop various projectiles, which provides greater safety to citizens and officers beyond the protection level of shield and personal body armor.
Quantity: 1
Purchase Price: $286,000.00
Fiscal Impact: Annual fiscal impact associated with this equipment cannot be determined at this time since the equipment has not been used by the Department for a sufficient amount of time to determine its annual operational costs. Since acquisition there have been no outside costs associated with maintenance of this vehicle, and the only costs associated with its use have been for fuel. The fiscal impact of this piece of equipment will be updated with the Department’s annual review.
B. MOBILE COMMAND POST VEHICLE (MCP)
A vehicle utilized as a mobile office that provides shelter, access to Department computer systems, and restroom facilities during extended events.
Current Inventory:
LDV MCP VEHICLE
Description: The MCP can also be utilized for SWAT/HNT, critical incidents, preplanned large events, searching for missing persons, natural disasters, and community events. The vehicle is currently housed inside an enclosed structure on the property of the department’s Special Services building. The vehicle is the primary command and control platform for the Department’s SWAT team during training and SWAT operations.
Quantity: 1
Purchase Price: $571,791.00
Fiscal Impact: There is no outside costs associated with annual maintenance since the city maintains and services the MCP.
C. RIFLES AND ASSOCIATED AMMUNITION
Firearm designed and intended to be fired from the shoulder and designed to use the energy in a fixed metallic cartridge to fire o nly a single projectile through a rifled bore for each single pull of the trigger.
Current Inventory:
1794440.1
SIG SAUER M400 RIFLE
Description: lightweight, magazine-fed, gas-operated semi-automatic rifle. Caliber 223/5.56, 16-inch barrel.
Quantity: 120
Purchase Price: $1,344.00/firearm
SIG SAUER 716 DMR G2 .308 PRECISION RIFLE
Description: Semi-automatic precision rifle with an 18-inch barrel, chambered in .308 Winchester, with night force 5.5-22x50 power optic
Quantity: 4
Purchase price: $1,977/rifle, $1,936/scope; $3,913 total/system.
REMINGTON 700 LTR .308 PRECISION RIFLE
Description: Bolt-action precision rifle with an 18-inch barrel, chambered in .308 Winchester
Quantity: 2
Purchase Price: $820.00 each
SIG SAUER MCX 5.56 SBR RIFLE
Description: Semi-automatic rifle with an 11-inch barrel, chambered in 5.56, with sound suppressors.
Quantity: 22
Purchase Price: $1,289.00 each
WINCHESTER.223 REMINGTON 55GR SILVER TIP RIFLE ROUND
Description: .223 Remington caliber, Fragmenting Polymer Tip (FPT), 55 grain bullet weight, brass cartridge case material.
Quantity: 10,000
Purchase Price: $894.60/1,000 rounds
1794440.1
WINCHESTER .223 REMINGTON 55GR FRANGIBLE RIFLE ROUND
Description: .223 Remington caliber, frangible, 55 grain bullet weight, brass cartridge case material.
Quantity: 5,000
Purchase Price: $894.60/1,000 rounds
WINCHESTER .223 REMI NGTON 55GR. FULL MET AL JACKET (FMJ) RIFL E ROUND
Description: 5.56 MM caliber, Full Metal Jacket (FMJ), 55 grain bullet weight, brass cartridge case material.
Quantity: 14,000
Purchase Price: $436.60/1,000 rounds
HORNADY .308 WIN 168GR A-MAX TAP PRECISION RIFLE ROUND
Description: .308 caliber, Tactical Application Police precision rifle round, 168 grain bullet weight, used in designated marksmen rifles.
Quantity: 1,600(Current Inventory)
Purchase Price: $1,890.00 per box of 1,400
Fiscal Impact: In addition to the purchase price for each piece of equipment listed above, there are annual maintenance costs of approximately $50 associated with each rifle.
D. NOISE-FLASH DIVERSIONARY DEVICES
A device used to distract a potentially dangerous person or persons.
Current Inventory:
DEFENSE TECHNOLOGY (DEFTEC), MODEL 8922 DIVERSONARY DEVICE Description: This is the standard noise flash diversionary device. It is non-bursting, non-fragmenting single use device that produces a 175db and 6 -8 million candela of light output. It is ideal for distracting potentially dangerous suspects during assaults, hostage rescue, building/room entry or other high-risk arrest situations.
Quantity: 24
1794440.1
Purchase Price: $60.29 each
Fiscal Impact: There are no annual maintenance costs associated with these pieces of equipment, therefore, the only associated costs are reflected in the acquisition costs reflected above.
E. DISTRACTION AND PAIN COMPLIANCE DEVICES
A device used to distract dangerous persons while deploying less lethal munitions.
Current Inventory:
DEFENSE TECHNOLOGY (DEFTEC), MODEL 1087 STINGER GRENADE Description: This is a hand-held, hand-thrown grenade and has an initial 1 second delayed fuse. Once the fuse is discharged at a low speed, the main charge detonates to produce a loud sound and bright flash of light, and the distribution of approximately 180 rubber pellets of .32 caliber size are expelled from the grenade, and the pellets can travel up to 50 ft. from the point of detonation.
Quantity: 96
Purchase Price: $46.86 each
Fiscal Impact: There are no annual maintenance costs associated with these pieces of equipment, therefore, the only associated costs are reflected in the acquisit ion costs reflected above.
F. EXPLOSIVE BREACHING TOOLS
Tools that are used to conduct an explosive breach.
Current Inventory:
KINETIC BREACHING TOOL (KBT) MODEL KIT-ATIKBT3-1000
Description: The KBT is a power actuated kinetic energy forced entry tool. It utilizes a crimped blank explosive charge which drives a captive steel impact plate directed at the breach point. The impact plate extends forward out of the clamshell shroud and impacts against the target with a high level of kinetic energy to defeat the entry point or fortification. The impact plate automatically retracts and is reset in the breaching device. The KBT uses semi-automatic cycling, allowing repeated strikes on hardened or multiple targets. The KBT’s intended use is for forced entry during high-risk operations with secure entry points and is designed to be operated
1794440.1
by a single officer/tactical team member. The KBT weighs 28 lbs. dimensions are 35 in. x 9.9 in. X 9.3 in. and has an audible report of 115dB. The KBT utilizes a proprietary blank cartridge to deliver up to 850 foot pounds of kinetic energy through the steel ram. There is no projectile or explosive energy that leaves the device except for the force of the ram, which is permanently captured in the breaching device.
Quantity: 1
Purchase Price: $10,579.38
Fiscal Impact: There are no annual maintenance costs associated with these pieces of equipment, therefore, the only associated costs are reflected in the acquisition costs reflected above.
KBT3-1100 POWER CARTRIDGES
Description: .45 Caliber crimped blank explosive charge delivering up to 850 ft. /lb. of force through a hardened steel ram. Power Cartridges are used for the Kinetic Breaching Tool (KBT) Model KIT -ATIKBT3-1000. No projectile or explosive energy leaves the device except the force of the ram which is permanently captured in the KBT from an 8-slot cylindrical magazine.
Quantity: 98
Purchase Price: $4.56 each
Fiscal Impact: Annual re-supply for training purposes and use during SWAT deployments estimated to be $454.56 annually.
REMINGTON 870 BREACHING SHOTGUN
Description: The modified short -barreled Remington 870 ballistic breaching shotgun is equipped with a serrated breaching standoff muzzle recoil reducer, rubber grip, plastic side saddle and tactical slinging system which fires a frangible ballistic breaching round. Depending on the constructed material of the door, operators of the Remington 870 Breaching Shotgun shall determine whether Tesar #1 Orange Cap 275 grain compressed copper frangible breaching round rat ed for solid wood doors, light steel, hinges and locks or Tesar #4 Yellow Cap 750 grain compressed copper frangible ballistic breaching round rated for heavy steel, hinges and locks will be used. Range of both Tesar #1 and Tesar #4 shall not exceed in excess of ½ mile. The Remington 870 Breaching Shotgun shall only be used by SWAT operators trained in the use of the Remington 870 ballistic breaching shotgun, with a stand -off of 6” inches less. Effectiveness depends on the constructed material of the door whether wood or steel, locking mechanism, hinges and/or door’s frame.
1794440.1
Quantity: 8
Purchase Price: $409.73 each
Fiscal Impact: Annual maintenance is approximately $50 for each breaching shotgun.
TESAR #1, ORANGE CAP 275 GRAIN COMPRESSED COPPER FRANGIBLE
BALLISTIC BREACHING ROUNDS
Description: Manufactured by Royal Arms, International the Tesar #1 Orange Cap 275 grain compressed copper frangible ballistic breaching round is used for the sole purpose of the immediate defeat of any/all door’s locking mechanisms or padlock hasps, minimizing the potential for ricochet or injury to any individual who operates with this frangible round. The frangible ballistic breaching round is rated for solid wood doors, light steel, hinges and locks.
Quantity: 140
Purchase Price: $4.50 each
Fiscal Impact: Annual re-supply for training purposes and use during SWAT deployments estimated to be $300.
TESAR #4, YELLOW CAP 750 GRAIN COMPRESSED COPPER FRANGIBLE
BALLISTIC BREACHING ROUNDS
Description: Manufactured by Royal Arms, International the Tesar #4 Yellow Cap 750 grain compressed copper frangible ballistic breaching round is used for the sole purpose of the immediate defeat of any/all door’s locking mechanisms or padlock hasps, minimizing the potential for ricochet or injury to any individual who operates with this frangible round. The frangible ballistic breaching round is rated for heavy steel, hinges and locks.
Quantity: 20
Purchase Price: $397.50
Fiscal Impact: Annual re-supply for training purposes and use during SWAT deployments estimated to be $300.
G. CHEMICAL AGENTS AND SMOKE CANISTERS
Canisters/Munitions containing chemical agents that are released when deployed.
Current Inventory:
1794440.1
COMBINE SYSTEMS (CTS), CS BAFFLED CANISTER GRENADE
Description: The design of the CS Baffled Canister Grenade allows the contents to burn within an internally baffled can and disperse the agent safely with reduced risk of fire. The grenade is designed primarily for indoor tactical situations to detect and/or dislodge a barricaded subject. This grenade will deliver 25 grams of agent during its 20-40 seconds burn time. The device is launchable. Part Number 5230B.
Quantity: 81
Purchase Price: $31.25 each
DEFENSE TECHNOLOGY, FLAMELESS TRI-CHAMBER CS GRENADE
Description: The design of the Tri -Chamber Flameless CS Grenade allows the contents to burn within an internal can and disperse the agent safely with reduced risk of fire. The grenade is designed primarily for indoor tactical situations to detect and/or dislodge a barricaded subject. This grenade will deliver 20 grams of agent during its 20 -30 seconds burn time. The device is not launchable. Part Number 1032.
Quantity: 8
Purchase Price: $35.72 each
DEFENSE TECHNOLOGY SPEDE-HEAT CS GRENADE
Description: The Spede -Heat CS Grenade is a high volume, continuous burn munition. It expels a CS payload of 81.2 grams in approximately 20 -40 seconds.
The CS is discharged through four gas ports on top of the canister, three gas ports on the side, and one gas port on the bottom. The device is launchable. Part Number 1072.
Quantity: 11
Purchase Price: $36.71 each
DEFENSE TECHNOLOGY RIOT CONTROL CONTINUOUS DISCHARGE
GRENADE, OC
Description: The Riot Control OC Grenade is designed specifically for outdoor use in crowd control situations with a high -volume continuous burn that expels its payload in approximately 20-40 seconds through four gas ports located on the top of the canister. This grenade can be used to conceal tactical movement or to route a crowd. The volume of smoke and agent is vast and obtrusive. This launchable
1794440.1
grenade is 6.0 in. by 2.6 in. and hold approximately 25g of OC chemical agent. Part Number: 1056.
Quantity: 5
Purchase Price: $44.76 each
DEFENSE TECHNOLOGY POCKET TACTICAL GRENADE, CS
Description: The Pocket Tactical CS Grenade is small, and lightweight. The 25.2g of CS chemical agent will burn approximately 20 -40 seconds. At 4.75 in. by 1.4 inches in size, it easily fits in most tactical pouches. Though this device is slightly over four inches in length, it produces a smoke cloud so fast it appears to be an enveloping screen produced by a full-size tactical grenade. Part Number 1016.
Quantity: 3
Purchase Price: $22.38 each
DEFENSE TECHNOLOGY 40MM CS FERRET LIQUID BARRICADE
PENETRATING PROJECTILE ROUND
Description: The 40MM CS Ferret Liquid munition is a frangible projectile filled with chemical agent. It is designed to deliver chemical agents in barricade situations from a 40mm launcher. Spin stabilization from barrel rifli ng affords maximum stand-off distance and accuracy for safety. The munition is non-burning and suitable for indoor use. It is designed to penetrate barriers, such as windows, hollow core doors, wallboard, and thin plywood. Upon impacting the barrier, the nose cone ruptures and instantaneously delivers 6.9 grams of chemical payload inside of a structure or vehicle. The active CS agent instantaneously discharges on impact. Part Number 2262.
Quantity: 18
Purchase Price: $26.90 each
DEFENSE TECHNOLOGY OC AEROSOL GRENADE 1.3% FOGGER, 6oz
Description: The 1 oz. / 6 oz. OC Aerosol Grenade will deliver its payload of 1/3% MC% OC in 15 -20 seconds. This is an anatomized mist which enhances the pungent 1.3% OC formulation. Ideal for area denial areas like attics, garages, etc.
This device has minimum clean up. The canister may also be handheld to direct the spray pattern. This product is designed to provide room clearing ability with minimum clear up requirements. Part number 56854.
Quantity: 4
1794440.1
Purchase Price: $21.90 each
DEFENSE TECHNOLOGY MILITARY-STYLE BLACK SMOKE GRENADE
Description: The Maximum Smoke Grenade is designed specifically for outdoor use in crowd control situations with a high volume continuous burn that expels its payload in approximately 30-40 seconds through four gas ports located on the top of the canister. This grenade can be used to conceal tactical movement or to reroute a crowd. The volume of smoke is fast and obtrusive. This launchable colored smoke grenade is 6 x 2.35 inches and holds approximately 2.9 ounces of active agent. Part number 1062.
Quantity: 1
Purchase Price: $45.33 each
DEFENSE TECHNOLOGY MILITARY-STYLE SAF-SMOKE GRENADE
Description: The Saf -Smoke Grenade was designed for training, but may also be used in operations. The Saf-Smoke Grenade offer the same approximate burn times as the Spede -Heat Grenade in CN or CS and the Riot Control Grenade in CN or CS. The similar burn times make it the appropriate choice for training or simulation deployment of chemical agent canisters. The Saf-Smoke formulation is considered to be less toxic than Hexachloroethane (HC) smoke. The Saf-Smoke Grenade emits a very white smoke. Part number 1063.
Quantity: 1
Purchase Price: $32.30 each
DEFENSE TECHNOLOGY SKAT SHELL 40MM MULTIPLE PROJECTILE ROUND, CS
Description: The Skat Shell 40mm CS multiple chemical projectile round is designed to deliver multiple CS canisters from a 40mm launcher. It is designed for outdoor use and has a fire-producing capability and has a maximum effective range of 80-100 yards. It is widely used as a crowd management tool for the rapid and broad deployment of a chemical agent by a single grenadier. The Skat Shell contains four separate sub -munitions and provides a wide area of coverage. Part number 6172.
Quantity: 97
Purchase Price: $30.12 each
CTS LC5 CHEMICAL AGENT LAUNCHING CUPS
1794440.1
Description: The chemical agent launching cup is affixed to the barrel end of a Remington 870 shotgun and fastened onto the barrel by a metal band and hand - tightened screw. The launching cup is utili zed to hold launchable OC, CS, and smoke munitions to effectively launch them from a safe distance into the designated target area.
Quantity: 4
Purchase Price: $278.82 each
VULCAN MUNITIONS POLE
Description: The Vulcan Munitions Pole is utilized to safely deploy munitions into doors, windows, and openings of buildings and vehicles to introduce OC, CS, smoke, and diversionary devices to distract, disrupt, or incapacitate subjects barricaded in structures or vehicles. The Vulcan Munitions pole weights less t han 9 pounds and is capable of extending from less than 8 feet in length to 13 feet in length.
Quantity: 2
Purchase Price: $2,412.62 each
CUSTOM METAL CONCEPTS BURN SAFE
Description: The Burn Safe is a double walled container constructed of aluminum.
It is designed to contain the flames inside the inner chamber thereby reducing the probability of starting a fire. The Burn Safe weighs approximately 8 pounds and is hand-deployed by officers. The weight allows the user to successfully penetrate windows, scree ns, and glass doors. The Burn Safe allows the introduction of significant amounts of pyrotechnic chemical agent into the target, which increases the probability of a successful resolution.
Quantity: 2
Purchase Price: $1,812.00 each
CUSTOM METAL CONCEPTS GAS RAM
Description: The Gas Ram is a multi -use tool that can be utilized for forced entry as a door ram or be deployed as a pyrotechnic Chemical Agent delivery system.
The Gas Ram is equipped with a 12 inch or 24 inch metal probe capable of penetrating walls, doors, sheet metal siding and into vehicles. Inserting the longer 24 inch probe allows use through roofs and dead air spaces. Both probes are effective in delivering significant amounts of pyrotechnic chemical agents with a minimal probability of starting fires.
1794440.1
Quantity: 1
Purchase Price: $1,500.00
DEFENSE TECHNOLOGY, 12 -GUAGE MUZZLE BANG/LAUNCHING
CARTRIDGE ROUND
Description: The 1210 12-Gauge Muzzle Bang/Launching Cartridge incorporates an opaque shell and utilizes black powder as the propellant. It has the ability to be used alone as a Muzzle Bang for crowd management or for propelling grenades when equipped with and using a Department authorized launching cup. Part number 1210.
Quantity: 60
Purchase Price: $7.13 each
Fiscal Impact: There are no a nnual maintenance costs associated with these pieces of equipment, therefore, the only associated costs are reflected in the acquisition costs reflected above.
H. PEPPERBALL LAUNCHER AND ASSOCIATED MUNITIONS
A device that discharges irritant projectiles.
Current Inventory:
TIPPMANN PEPPERBALL GUN
Description: A compressed -air powered launcher designed to fire non -lethal PepperBall projectiles.
Quantity: 7
Purchase Price: $316.79 each
PEPPERBALL LIVE-X PROJECTILE
Description: The Live Projectile contains a concentrated amount of PAVA pepper powder. One round of LIVE -X contains the equivalent to 10 PepperBall rounds.
Discharged from a PepperBall Launcher, the projectile has a velocity of 280 -350 FPS. The projectile has a direct impact of 60 ft. and an area of saturation of 150+ft.
The projectile contains 5% PAVA Powder.
Quantity: 2,400
1794440.1
Purchase Price: $928.00/case of 375 projectiles
Fiscal Impact : There are no annual maintenance costs associated with these pieces of equipment, therefore, the only associated costs are reflected in the acquisition costs reflected above.
I. 40 MM LAUNCHER AND ASSOCIATED MUNITIONS
40MM Launchers are utilized by department personnel as a less lethal tool to launch impact rounds.
Current Inventory:
DEFENSE TECHNOLOGY, 40MM SINGLE SHOT LAUNCHER
Description: The 40MM Single Launcher is a tactical single shot launcher. It will fire standard 40mm less lethal ammunition, up to 4.8 inches in cartridge length. It will launch a 40mm less lethal round up to 131 feet.
Quantity: 5
Purchase Price: $888.70 each
DEFENSE TECHNOLOGY, 40MM EXACT IMPACT SPONGE
Description: A less lethal 40mm lightweight plastic and foam projectile fired from a single or multi-round purpose built 40mm grenade launcher with a rifled barrel at 325 FPS. The 30 -gram foam projectile delivers 120 foot pounds of energy on impact. The 40mm Exact Impact Sponge Round provides accurate and effective performance when fired from the approved distance of not less than five (5) feet and as far as 131 feet from the target.
Quantity: 290
Purchase Price: $20.61 each
Fiscal Impact: In addition to the acquisition costs reflected above, there are annual maintenance costs estimated to be approximately $50 for each launcher.
J. LESS LETHAL SHOTGUN AND ASSOCIATED MUNITIONS
Device used to deploy the less lethal 12-gauge Super-Sock Beanbag Round.
Current Inventory:
REMINGTON 870 LESS LETHAL SHOTGUN
1794440.1
Description: The Remington 870 Less Lethal Shotgun is used to deploy the less lethal 12-gauge Super-Sock Beanbag Round up to a distance of 75 feet. The range of the weapon system helps to maintain space between officers and a suspect reducing the immediacy of the threat which is a principle of de-escalation.
Quantity: 65
Purchase Price: $395.75 each
DRAG STABILIZED 12-GAUGE BEANBAG ROUND
Description: A less lethal 2.4-inch 12-gauge shotgun round firing a ballistic fiber bag filled with 40 grams of lead shot at a velocity of 270-290 feet per second (FPS).
Drag Stabilized rounds are discharged from a dedicated 12 -gauge shotgun that is distinguishable by an orange butt stock and fore grip. This round provides accurate and effective performance when fired from the approved distance of not fewer than five (5) feet. The maximum effective range of this munition is up to 75 feet from the target. The Drag Stabiliz ed Model is in its deployed state immediately upon exiting the barrel. It does not require a minimum range to “unfold” or “stabilize.” The Drag Stabilized Model is an aerodynamic projectile. However, accuracy is relative to the shotgun, barrel length, envi ronmental conditions, and the operator.
The Drag Stabilized Model is very accurate. However, effectiveness depends on many variables, such as distance, clothing, stature, and the point where the projectile impacts.
Quantity: 420
Purchase Price: $6.47each
Fiscal Impact: In addition to the acquisition costs reflected above, there are annual maintenance costs estimated to be $50 for each shotgun.
6. ANTICIPATED ACQUISITION OF ADDITIONAL MILITARY EQUIPMENT
Aside from replenishment of fungible munitions describe d in Section 5 above, the Department does not anticipate that it will seek to acquire any additional military equipment in the next calendar year. Should the needs of the Department change, it will seek the authorization of the Garden Grove City Council pr ior to acquisition of such equipment as required by Policy 706 and Government Code section 7070 et seq.
1794447.1
Policy
706
Garden Grove Police Department
Policy Manual
Military Equipment
706.1 PURPOSE AND SCOPE
State
The purpose of this policy is to provide guidelines for the approval, acquisition, and reporting requirements of military equipment (Government Code § 7070; Government Code § 7071; Government Code § 7072). This policy is provided to fulfill the obli gations set forth in Assembly Bill No. 481. These obligations include but are not limited to seeking approval on specific items deemed to be military equipment and requirements related to compliance, annual reporting, cataloging, and complaints regarding these items.
706.1.1 DEFINITIONS
State
Definitions related to this policy include (Government Code § 7070):
Governing body – The elected or appointed body that oversees the Department which, for the purposes of the Department, would be the Garden Grove City Council.
Military equipment – Any of a wide variety of items as defined by California Government Code § 7070, subsections (c)(1) through (c)(16).
Includes but is not limited to the following:
• Unmanned, remotely piloted, powered aerial or ground vehicles.
• Mine-resistant ambush-protected (MRAP) vehicles or armored personnel carriers.
• High mobility multipurpose wheeled vehicles (HMMWV), two-and-one-half-ton trucks, five-ton trucks, or wheeled vehicles that have a breaching or entry apparatus attached.
• Tracked armored vehicles that provide ballistic protection to their occupants.
• Command and control vehicles that are either built or modified to facilitate the operational control and direction of public safety units.
• Weaponized aircraft, vessels, or vehicles of any kind.
• Battering rams, slugs, and breaching apparatuses that are explosive in nature. This does not include a handheld, one-person ram.
• Firearms and ammunition of .50 caliber or greater, excluding standard-issue shotguns and standard-issue shotgun ammunition.
• Specialized firearms and ammunition of less than .50 caliber, including firearms and accessories identified as assault weapons in Penal Code § 30510 and Penal Code § 30515, with the exception of standard-issue service weapons and their ammunition.
• Any firearm or firearm accessory that is designed to launch explosive projectiles.
• Noise-flash diversionary devices and explosive breaching tools.
• Munitions containing tear gas or OC, excluding standard, service-issued handheld pepper spray.
1794447.1
• TASER® Shockwave, microwave weapons, water cannons, and long-range acoustic devices (LRADs).
• Kinetic energy weapons and munitions.
• Any other equipment as determined by a governing body or a state agency to require additional oversight.
Garden Grove Police Department
Policy Manual
Military Equipment
1794447.1
706.2 POLICY
State
It is the policy of the Garden Grove Police Department that members of this Department comply with the provisions of Government Code § 7071 with respect to military equipment.
706.3 MILITARY EQUIPMENT COORDINATOR
Best Practice
The Chief of Police should designate the Professional Standards Division Lieutenant to act as the military equipment coordinator. The responsibilities of the military equipment coordinator include but are not limited to:
(a) Acting as liaison to the Garden Grove City Council for matters related to the requirements of this policy.
(b) Identifying department equipment that qualifies as military equipment in the current possession of the Department, and any equipment the Department intends to acquire that requires approval by the Garden Grove City Council.
(c) Conducting an inventory of all Department military equipment at least annually.
(d) Collaborating with any allied agency that may use military equipment within the jurisdiction of Garden Grove Police Department (Government Code § 7071).
(e) Preparing for, scheduling, and coordinating the annual community engagement meeting to include:
1. Publicizing the details of the meeting.
2. Preparing for public questions regarding the Department’s funding, acquisition, and use of equipment.
(f) Preparing the annual military equipment report for submission to the Chief of Police and ensuring that the report is made available on the Department website (Government Code § 7072).
(g) Providing information on the Department website which details how members of the public can ask questions, raise concerns, or make comments regarding the military equipment policy, or any use of military equipment by members of the Department.
The military equipment coordinator is required to respond to questions, comments, and/or concerns as set forth in requirements of section 706.9 of this policy.
(h) Ensuring that any proposed and/or approved military equipment use policy is made available on the Department website for as long as the military equipment identified in the policy is available for use. (Government Code § 7071(d)(2))
706.4 MILITARY EQUIPMENT USE CONSIDERATIONS
The military equipment acquired and authorized by the Department is:
(a) Necessary because there is no reasonable alternative that can achieve the same objective of officer and civilian safety.
(b) Reasonably cost effective compared to available alternatives that can achieve the same objective of officer and civilian safety.
Garden Grove Police Department
Policy Manual
Military Equipment
1794447.1
706.5 MILITARY EQUIPMENT INVENTORY
State
The following constitutes an inventory of equipment owned and/or in the possession of the Garden Grove Police Department which is deemed to be military equipment as defined by this policy and state law:
See Attachment: 706.5 MILITARY EQUIPMENT INVENTORY
706.6 APPROVAL
State
The Chief of Police or the authorized designee shall obtain approval from the City Council by way of an ordinance adopting the military equipment policy. As part of the approval process, the Chief of Police or the authorized designee shall ensure the propo sed military equipment policy is submitted to the City Council and is available on the Department website at least 30 days prior to any public hearing concerning the military equipment policy at issue (Government Code § 7071).
The military equipment policy must be approved by the governing body prior to engaging in any of the following (Government Code § 7071):
(a) Requesting military equipment made available pursuant to 10 USC § 2576a.
(b) Seeking funds for military equipment, including but not limited to applying for a grant, soliciting or accepting private, local, state, or federal funds, in-kind donations, or other donations or transfers.
(c) Acquiring military equipment either permanently or temporarily, including by borrowing or leasing.
(d) Collaborating with another law enforcement agency in the deployment or other use of military equipment within the jurisdiction of this department.
(e) Using any new or existing military equipment for a purpose, in a manner, or by a person not previously approved by the governing body.
(f) Soliciting or responding to a proposal for, or entering into an agreement with, any other person or entity to seek funds for, apply to receive, acquire, use, or collaborate in the use of military equipment.
(g) Acquiring military equipment through any means not provided above.
706.7 COORDINATION WITH OTHER JURISDICTIONS
State
Military equipment used by other jurisdictions that are providing mutual aid to this Department shall comply with their respective military equipment use policy in rendering mutual aid.
706.8 ANNUAL REPORT
State
Upon approval of a military equipment policy, the Chief of Police or the authorized designee should submit a military equipment report to the governing body for each type of military equipment approved within one year of approval, and annually thereafter for as long as the military equipment is available for use (Government Code § 7072).
Garden Grove Police Department
Policy Manual
Military Equipment
1794447.1
The Chief of Police or the authorized designee should also make each annual military equipment report publicly available on the Department website for as long as the military equipment is available for use. The report shall include all information required by Government Code § 7072 for the preceding calendar year for each type of military equipment in department inventory.
Within 30 days of submitting and publicly releasing an annual report, the Department shall hold at least one well-publicized and conveniently located community engagement meeting, at which the Department should discuss the report and respond to public questions regarding the funding, acquisition, or use of military equipment.
706.9 CITIZEN COMMENTS, QUESTIONS AND CONCERNS
State
(a) Complaints. Any complaint regarding the use of military equipment governed by this policy shall be processed in accordance with the Personnel Complaint Policy.
(b) Questions, Comments, and Concerns. The military equipment coordinator designated by the Chief of Police shall be required to include information on the Department’s website detailing how members of the public can submit questions, comments, or concerns regarding the military equipment use policy, or use of military equipment that is governed by this policy. This information shall include the military use coordinator’s email address and telephone number. The military equipment coordinator must respond, in writing when possible, to any question, comment, or concern raised by a member of the public within 10 days of receipt of the comment, question, or concern. When appropriate, the military equipment coordinator will forward any concern which rises to the level of a citizen complaint to the professional standards division for handling pursuant to the Personnel Complaint Policy. .
706.9 COMPLIANCE AND OVERSIGHT
State
(a) Compliance. All members of the Department are required to comply with this military use policy. Failure of any member to comply with this military use policy may subject that member to discipline as set forth in the Personnel Complaint Policy. . (b) Oversight. The City Council of the City of Garden Grove shall have oversight authority with respect to the provisions of this policy and its implementation.
Garden Grove Police Department
Policy Manual
Military Equipment
1794447.1
ATTACHMENT 706.5 TO GARDEN GROVE POLICE DEPARTMENT
POLICY 706
MILITARY EQUIPMENT INVENTORY
The following constitutes an inventory of equipment owned and/or in the possession of the Garden Grove Police Department which is deemed to be military equipment as defined by this policy and state law:
1. RESCUE VEHICLE
Commercially produced wheeled rescue personnel vehicle utilized for law enforcement purposes.
Current Inventory:
LENCO BEARCAT G2
Description: Rescue vehicle that seats 10 -12 personnel with open floor plan that allows for rescue of down personnel. It can stop various projectiles, which provides greater safety to citizens and officers beyond the protection level of shield and personal body armor. The armored vehicle was purchased by the Department prior to January 1, 2022, and was delivered on April 6, 2022.
Quantity: 1
Purchase Price: $286,000.00
Purpose: To be used in response to critical incidents to enhance officer and community safety, improve scene containment and stabilization, and assist in resolving critical incidents.
Authorized Use: The use of the rescue vehicle shall only be authorized by a watch commander or SWAT commander, based on the specific circumstances of a given critical incident. Rescue vehicles shall be used only by officers trained in their deployment and in a manner consistent with Department policy and training.
Expected Lifespan: 25 years.
Fiscal Impact: Annual fiscal impact cannot be determined at this time since the equipme nt has not been used by the Department for a sufficient amount of time to allow the Department to determine its operational costs . Since acquisition, there have been no outside maintenance costs associated with the vehicle and the only associated costs have been for fuel. The fiscal impact of this piece of equipment will be updated with the Department’s next annual review.
Training: All driver/operators shall attend formalized instruction and be trained in vehicle operations and practical driving instruction.
Garden Grove Police Department
Policy Manual
Military Equipment
1794447.1
Legal and Procedural Rules: It is the policy of the Department to utilize rescue vehicles only for official law enforcement purposes, and pursuant to State and Federal law.
2. MOBILE COMMAND POST VEHICLE (MCP)
A vehicle utilized as a mobile office that provides shelter, access to Department computer systems, and restroom facilities during extended events.
Current Inventory:
LDV MCP VEHICLE
Description: The MCP can also be utilized for SWAT/HNT , critical incidents, preplanned large events, searching for missing persons, natural disasters, and community events. The vehicle is currently housed inside an enclosed structure on the property of the department’s Special Services building. The vehicle is the primary command and control platform for the Department’s SWAT team during training and SWAT operations.
Quantity: 1
Purchase Price: $571,791.00
Purpose: To be used based on t he specific circumstances of a given critical incident, large event, natural disaster, or community event that is taking place.
Authorized Use: Only officers trained in the deployment and operations in a manner consistent with Department policy and trainin g are authorized to operate the MCP.
Furthermore, only officers who have completed the California State Class B Commercial driving school and become properly licensed will be allowed to drive the MCP. Situations in which the MCP is authorized for use would include, but not be limited to , critical incidents, emergencies, and natural disasters.
Expected Lifespan: The MCP, has a 20-year lifespan on chassis and vehicle structure.
Fiscal Impact: There is no outside costs associated with annual maintenance since the city maintains and services the MCP.
Training: The driver/operator shall receive training in the safe handling of the vehicle on a closed training course. Once the operator has shown competence in vehicle handling, the driver/operator will drive the vehicle throughout the city with an experienced driver.
Driver/operators shall also undergo California Department of Motor Vehicles commercial vehicle testing.
Legal and Procedural Rules: It is the policy of the Department to use the MCP only for official law enforcement purposes, and in accordance with California State law regarding the operation of motor vehicles.
3. RIFLES AND ASSOCIATED AMMUNITION
Garden Grove Police Department
Policy Manual
Military Equipment
1794447.1
Firearm designed and intended to be fired from the shoulder and designed to use the energy in a fixed metallic cartridge to fire only a single projectile through a rifled bore for each single pull of the trigger.
Current Inventory:
SIG SAUER M400 RIFLE
Description: lightweight, magazine-fed, gas-operated semi-automatic rifle. Caliber 223/5.56, 16-inch barrel.
Quantity: 120
Purchase Price: $1,344.00/firearm
SIG SAUER 716 DMR G2 .308 PRECISION RIFLE
Description: Semi-automatic precision rifle with an 18 -inch barrel, chambered in .308 Winchester, with night force 5.5-22x50 power optic
Quantity: 4
Purchase price: $1,977/rifle, $1,936/scope; $3,913 total/system.
REMINGTON 700 LTR .308 PRECISION RIFLE
Description: Bolt-action precision rifle with an 18 -inch barrel, chambered in .308 Winchester
Quantity: 2
Purchase Price: $820.00 each
SIG SAUER MCX 5.56 SBR RIFLE
Description: Semi-automatic rifle with an 11 -inch barrel, chambered in 5.56, with sound suppressors.
Quantity: 22
Purchase Price: $1,289.00 each
WINCHESTER.223 REMINGTON 55GR SILVER TIP RIFLE ROUND
Description: .223 Remington caliber, Fragmenting Polymer Tip (FPT), 55 grain bullet weight, brass cartridge case material.
Quantity: 10,000
Garden Grove Police Department
Policy Manual
Military Equipment
1794447.1
Purchase Price: $894.60/1,000 rounds
WINCHESTER .223 REMINGTON 55GR FRANGIBLE RIFLE ROUND
Description: .223 Remington caliber, frangible, 55 grain bullet weight, brass cartridge case material.
Quantity: 5,000
Purchase Price: $894.60/1,000 rounds
WINCHESTER .223 REMINGTON 55GR. FULL METAL JACKET (FMJ) RIFLE ROUND Description: 5.56 MM caliber, Full Metal Jacket (FMJ), 55 grain bullet weight, brass cartridge case material.
Quantity: 14,000
Purchase Price: $436.60/1,000 rounds
HORNADY .308 WIN 168GR A-MAX TAP PRECISION RIFLE ROUND
Description: .308 caliber, Tactical Application Police precision rifle round, 168 grain bullet weight, used in designated marksmen rifles.
Quantity: 1,600(Current Inventory)
Purchase Price: $1,890.00 per box of 1,400
Purpose: To be used as precision weapons to address a threat with more precision and/or greater distances than a handgun, if present and if use is feasible.
Authorized Use: Only officers who have received training with the specific firearm are authorized to use that rifle.
Expected Life Span: No expiration date.
Fiscal Impact: Annual maintenance is approximately $50 for each rifle.
Training: Prior to using a rifle, officers must be certified by POST instructors in the operation of the rifle. Additionally, all members that operate any rifle are required to pass a range qualification four times a year.
Legal and Procedural Rule: It is the policy of the Garden Grove Police Department to utilize rifles only for official law enforcement purposes, and pursuant to Sta te and Federal law regarding the use of force.
4. NOISE-FLASH DIVERSIONARY DEVICES
Garden Grove Police Department
Policy Manual
Military Equipment
1794447.1
A device used to distract a potentially dangerous person or persons.
Current Inventory:
DEFENSE TECHNOLOGY (DEFTEC), MODEL 8922 DIVERSONARY DEVICE Description: This is the standard noise flash diversionary device. It is non -bursting, non-fragmenting single use device that produces a 175db and 6-8 million candela of light output. It is ideal for distracting potentially dangerous suspects during assaults, hostage rescue, building/room entry or other high-risk arrest situations.
Quantity: 24
Purchase Price: $60.29 each
Purpose: A distraction device is ideal for distracting dangerous suspects during assaults, hostage rescue, room entry or other high -risk arrest situations. To produce atmospheric overpressure and brilliant white light which, as a result, can cause short-term (6 - 8 seconds) physiological/psychological sensory deprivation to give officers a tactical advantage.
Authorized Use: Diversionary Devices shall only be used:
1. By officers who have been trained in their proper use.
2. In hostage and barricaded subject situations.
3. In high-risk warrant (search/arrest) services where there may be extreme hazards to officers.
4. During other high-risk situations where their use would enhance officer safety.
5. During training exercises.
Expected Lifespan: Until used.
Fiscal Impact: No annual maintenance.
Training: Prior to use, officers must attend diversionary device training that is conducted by POST certified instructors.
Legal and Pro cedural Rules: Use is established in the Garden Grove Police Department Special Weapons and Tactics Manual. It is the policy of the GGPD to utilize diversion devices only for official law enforcement purposes, and pursuant to State and Federal law regarding the use of force.
5. DISTRACTION AND PAIN COMPLIANCE DEVICES
Garden Grove Police Department
Policy Manual
Military Equipment
1794447.1
A device used to distract dangerous persons while deploying less lethal munitions.
Current Inventory:
DEFENSE TECHNOLOGY (DEFTEC), MODEL 1087 STINGER GRENADE Description: This is a hand-held, hand-thrown grenade and has an initial 1 second delayed fuse. Once the fuse is discharged at a low speed, the main charge detonates to produce a loud sound and bright flash of light, and the distribution of approximately 180 rubber pellets of .32 caliber size are expelled from the grenade, and the pellets can travel up to 50 ft. from the point of detonation.
Quantity: 96
Purchase Price: $46.86 each
Purpose: To limit the escalation of conflict and decrease use of lethal force when feasible.
Situations for use of the less lethal weapon systems may include, but are not limited to:
1. Self-destructive, dangerous and/or combative individuals.
2. Riot/crowd control and civil unrest incidents.
3. Circumstances where a tactical advantage can be obtained.
4. Potentially vicious animals.
5. Training exercises or approved demonstrations.
Authorized Use: Stinger Grenade Devices shall only be used:
1. Self-destructive, dangerous and/or combative individuals.
2. Riot/crowd control and civil unrest incidents.
3. Circumstances where a tactical advantage can be obtained.
4. Potentially vicious animals.
5. Training exercises.
Expected Lifespan: Until used.
Fiscal Impact: No annual maintenance.
Training: Prior to use, officers must attend diversionary device training that is conducted by POST certified instructors.
Legal and Procedural Rules: It is the policy of the GGPD to utilize Stinger Grenades only for official law enforcement purposes, and pursuant to State and Federal law, including those regarding the use of force.
6. EXPLOSIVE BREACHING TOOLS
Garden Grove Police Department
Policy Manual
Military Equipment
1794447.1
Tools that are used to conduct an explosive breach.
Current Inventory:
KINETIC BREACHING TOOL (KBT) MODEL KIT-ATIKBT3-1000
Description: The KBT is a power actuated kinetic energy forced entry tool. It utilizes a crimped blank explosive charge which drives a captive steel impact plate directed at the breach point. The impact plate extends forward out of the clamshell shroud and impacts against the target with a high level of kinetic energy to defeat the entry point or fortifica tion. The impact plate automatically retracts and is reset in the breaching device. The KBT uses semi -automatic cycling, allowing repeated strikes on hardened or multiple targets. The KBT’s intended use is for forced entry during high-risk operations wi th secure entry points and is designed to be operated by a single officer/tactical team member. The KBT weighs 28 lbs. dimensions are 35 in. x
9.9 in. X 9.3 in. and has an audible report of 115dB. The KBT utilizes a proprietary blank cartridge to deliver u p to 850 foot pounds of kinetic energy through the steel ram. There is no projectile or explosive energy that leaves the device except for the force of the ram, which is permanently captured in the breaching device.
Quantity: 1
Purchase Price: $10,579.38
Purpose: To safely gain entry into a structure.
Authorized Use: Use of the KBT may only occur after the operator gains authorization by the Incident Commander, SWAT Commander in the field, SWAT team leader, SWAT assistant team leader, and/or during training exercises.
Expected Lifespan: Kinetic Breaching Tool (KBT) - 30 years. Blank cartridges – 5 years (preferably rotate rounds within 1 year).
Fiscal Impact: No annual maintenance.
Training: All officers who use explosive breaching tools shall attend and successfully pass a certified course in the use of any breaching or explosive entry tool.
Legal and Procedural Rules: It is the policy of the Garden Grove Police Department to utilize breaching tools only for official law enforcement purposes, and pursuant to State and Federal law.
KBT3-1100 POWER CARTRIDGES
Description: .45 Caliber crimped blank explosive charge delivering up to 850 ft. /lb. of force through a hardened steel ram. Power Cartridges are used for the Kinetic Breaching Tool (KBT) Model KIT-ATIKBT3-1000. No projectile or explosive energy
leaves the device except the force of the ram which is permanently captured in the KBT from an 8-slot cylindrical magazine. Page 307 of 362 Garden Grove Police Department
Policy Manual
Military Equipment
1794447.1
Quantity: 98
Purchase Price: $4.56 each
Purpose: The immediate defeat of any locking mechanism.
Authorized Use: SWAT personnel only who have been trained in the use of the Kinetic Breaching Tool (KBT) Model KIT-ATIKBT3-1000.
Expected Life Span: 5 years, preferably rotate rounds within 1 year.
Fiscal Impact: Annual re-supply for training purposes and use during SWAT deployments $454.56 annually.
Training: All SWAT personnel who have attended and successfully passed a POST approved basic SWAT school are trained quarterly and receive additional training internally.
SWAT operators who utilize the power cartridges shall have completed an approved and certified course in the use of any breaching or explosive entry tool.
Legal and Procedural Rules: It is the policy of the Garden Grove Police Department to utilize breaching tools only for official law enforcement purposes, and pursuant to State and Federal law.
REMINGTON 870 BREACHING SHOTGUN
Description: The modified short barreled Remington 870 ballistic breaching shotgun is equipped with a serrated breac hing standoff muzzle recoil reducer, rubber grip, plastic side saddle and tactical slinging system which fires a frangible ballistic breaching round. Depending on the constructed material of the door, operators of the Remington 870 Breaching Shotgun shall determine whether Tesar #1 Orange Cap 275 grain compressed copper frangible breaching round rated for solid wood doors, light steel, hinges and locks or Tesar #4 Yellow Cap 750 grain compressed copper frangible ballistic breaching round rated for heavy ste el, hinges and locks will be used. Range of both Tesar #1 and Tesar #4 shall not exceed in excess of ½ mile.
The Remington 870 Breaching Shotgun shall only be used by SWAT operators trained in the use of the Remington 870 ballistic breaching shotgun, with a stand-off of 6” inches less. Effectiveness depends on the constructed material of the door whether wood or steel, locking mechanism, hinges and/or door’s frame.
Quantity: 8
Purchase Price: $409.73 each
Purpose: To safely gain entry into a structure and or/interior doors and the immediate defeat of any/all locking mechanisms.
Garden Grove Police Department
Policy Manual
Military Equipment
1794447.1
Authorized Use: Use of the Remington 870 Breaching Shotgun may only occur after the operator gains authorization by the Incident Command er, SWAT Commander in the field, SWAT team leader, SWAT assistant team leader, and/or during training exercises.
Expected Lifespan: Remington 870 Breaching Shotgun- 25 years, Tesar #1 Orange Cap 275 grain compressed copper frangible ballistic breaching ro unds- no listed expiration date.
Tesar #4 Yellow Cap 750 grain compressed copper frangible ballistic breaching rounds- no listed expiration date.
Fiscal Impact: Annual maintenance is approximately $50 for each breaching shotgun.
Training: All SWAT person nel who have attended and successfully passed a POST approved basic SWAT school are training quarterly and receive additional training internally.
SWAT operators who utilize the Remington 870 Breaching Shotgun have completed an approved and certified course in the use of any breaching or explosive entry tool.
Legal and Procedural Rules: It is the policy of the Garden Grove Police Department to utilize breaching tools only for official law enforcement purposes, and pursuant to State and Federal law.
TESAR #1, ORANGE CAP 275 GRAIN COMPRESSED COPPER FRANGIBLE BALLISTIC
BREACHING ROUNDS
Description: Manufactured by Royal Arms, International the Tesar #1 Orange Cap 275 grain compressed copper frangible ballistic breaching round is used for the sole purpose of t he immediate defeat of any/all door’s locking mechanisms or padlock hasps, minimizing the potential for ricochet or injury to any individual who operates with this frangible round. The frangible ballistic breaching round is rated for solid wood doors, light steel, hinges and locks.
Quantity: 140
Purchase Price: $4.50 each
Purpose: The immediate defeat of a door’s locking mechanism.
Authorized Use: SWAT personnel only who have been trained in the use of the Remington 870 Ballistic Breaching Shotgun.
Expected Life Span: No listed expiration date.
Fiscal Impact: Annual re-supply for training purposes and use during SWAT deployments $300 yearly.
Training: All SWAT personnel who have attended and successfully passed a POST approved basic SWAT school are trained quarterly and receive additional training internally.
SWAT operators who utilize the Tesar #1 frangible ballistic breaching round shall have completed an approved and certified course in the use of any breaching or explosive entry tool.
Garden Grove Police Department
Policy Manual
Military Equipment
1794447.1
Legal and Procedural Rules: It is the policy of the Garden Grove Police Department to utilize breaching tools/rounds only for official law enforcement purposes, and pursuant to State and Federal law.
TESAR #4, YELLOW CAP 750 GRAIN COMPRESSED COPPER FRANGIBLE BALLISTIC
BREACHING ROUNDS
Description: Manufactured by Royal Arms, International the Tesar #4 Yellow Cap 750 grain compressed copper frangible ballistic breaching round is used for the sole purpose of the immediate defeat of any/all door’s locking mechanisms or pa dlock hasps, minimizing the potential for ricochet or injury to any individual who operates with this frangible round. The frangible ballistic breaching round is rated for heavy steel, hinges and locks.
Quantity: 20
Purchase Price: $397.50
Purpose: The immediate defeat of a door’s locking mechanism.
Authorized Use: SWAT personnel only who have been trained in the use of the Remington 870 Ballistic Breaching Shotgun.
Expected Life Span: No listed expiration date.
Fiscal Impact: Annual re-supply for train ing purposes and use during SWAT deployments $300 yearly.
Training: All SWAT personnel who have attended and successfully passed a POST approved basic SWAT school are trained quarterly and receive additional training internally.
SWAT operators who utiliz e the Tesar #4 frangible ballistic breaching round shall have completed an approved and certified course in the use of any breaching or explosive entry tool.
Legal and Procedural Rules: It is the policy of the Garden Grove Police Department to utilize breaching tools/rounds only for official law enforcement purposes, and pursuant to State and Federal law.
7. CHEMICAL AGENTS AND SMOKE CANISTERS
Canisters/Munitions containing chemical agents that are released when deployed.
Current Inventory:
COMBINE SYSTEMS (CTS), CS BAFFLED CANISTER GRENADE
Description: The design of the CS Baffled Canister Grenade allows the contents to burn within an internally baffled can and disperse the agent safely with reduced risk of fire. The grenade is designed primarily for indoor tactical situations to detect and/or
Garden Grove Police Department
Policy Manual
Military Equipment
1794447.1
dislodge a barricaded subject. This grenade will deliver 25 grams of agent during its 20-40 seconds burn time. The device is launchable. Part Number 5230B.
Quantity: 81
Purchase Price: $31.25 each
DEFENSE TECHNOLOGY, FLAMELESS TRI-CHAMBER CS GRENADE
Description: The design of the Tri -Chamber Flameless CS Grenade allows the contents to burn within an internal can and disperse the agent safely with reduced risk of fire. The grenade is designed primarily for indoor tact ical situations to detect and/or dislodge a barricaded subject. This grenade will deliver 20 grams of agent during its 20-30 seconds burn time. The device is not launchable. Part Number 1032.
Quantity: 8
Purchase Price: $35.72 each
DEFENSE TECHNOLOGY SPEDE-HEAT CS GRENADE
Description: The Spede -Heat CS Grenade is a high volume, continuous burn munition. It expels a CS payload of 81.2 grams in approximately 20 -40 seconds.
The CS is discharged through four gas ports on top of the canister, three gas port s on the side, and one gas port on the bottom. The device is launchable. Part Number 1072.
Quantity: 11
Purchase Price: $36.71 each
DEFENSE TECHNOLOGY RIOT CONTROL CONTINUOUS DISCHARGE GRENADE, OC Description: The Riot Control OC Grenade is designed specifically for outdoor use in crowd control situations with a high -volume continuous burn that expels its payload in approximately 20 -40 seconds through four gas ports located on the top of the canister. This grenade can be used to conceal tactical movement or to route a crowd.
The volume of smoke and agent is vast and obtrusive. This launchable grenade is
6.0 in. by 2.6 in. and hold approximately 25g of OC chemical agent. Part Number:
1056.
Quantity: 5
Purchase Price: $44.76 each
DEFENSE TECHNOLOGY POCKET TACTICAL GRENADE, CS
Description: The Pocket Tactical CS Grenade is small, and lightweight. The 25.2g of CS chemical agent will burn approximately 20-40 seconds. At 4.75 in. by 1.4 inches in size, it easily fits in most tactical pouches. Though this device is slightly over four
Garden Grove Police Department
Policy Manual
Military Equipment
1794447.1
inches in length, it produces a smoke cloud so fast it appears to be an enveloping screen produced by a full-size tactical grenade. Part Number 1016.
Quantity: 3
Purchase Price: $22.38 each
DEFENSE TECHNOLOGY 40MM CS FERRET LIQ UID BARRICADE PENETRATING
PROJECTILE ROUND
Description: The 40MM CS Ferret Liquid munition is a frangible projectile filled with chemical agent. It is designed to deliver chemical agents in barricade situations from a 40mm launcher. Spin stabilization fro m barrel rifling affords maximum stand -off distance and accuracy for safety. The munition is non-burning and suitable for indoor use. It is designed to penetrate barriers, such as windows, hollow core doors, wallboard, and thin plywood. Upon impacting the barrier, the nose cone ruptures and instantaneously delivers 6.9 grams of chemical payload inside of a structure or vehicle. The active CS agent instantaneously discharges on impact. Part Number 2262.
Quantity: 18
Purchase Price: $26.90 each
DEFENSE TECHNOLOGY OC AEROSOL GRENADE 1.3% FOGGER, 6oz
Description: The 1 oz. / 6 oz. OC Aerosol Grenade will deliver its payload of 1/3% MC% OC in 15-20 seconds. This is an anatomized mist which enhances the pungent
1.3% OC formulation. Ideal for area denial areas like attics, garages, etc. This device has minimum clean up. The canister may also be handheld to direct the spray pattern.
This product is designed to provide room clearing ability with minimum clear up requirements. Part number 56854.
Quantity: 4
Purchase Price: $21.90 each
DEFENSE TECHNOLOGY MILITARY-STYLE BLACK SMOKE GRENADE
Description: The Maximum Smoke Grenade is designed specifically for outdoor use in crowd control situations with a high volume continuous burn that expels its payload in approximately 30-40 seconds through four gas ports located on the top of the canister. This grenade can be used to conceal tactical movement or to reroute a crowd. The volume of smoke is fast and obtrusive. This launchable colored smoke grenade is 6 x 2.35 inches and holds approximately 2.9 ounces of active agent. Part number 1062.
Quantity: 1
Purchase Price: $45.33 each
Garden Grove Police Department
Policy Manual
Military Equipment
1794447.1
DEFENSE TECHNOLOGY MILITARY-STYLE SAF-SMOKE GRENADE
Description: The Saf -Smoke Grenade was designed for training, but may also be used in operations. The Saf-Smoke Grenade offer the same approximate burn times as the Spede-Heat Grenade in CN or CS and the Riot Control Grenade in CN or CS.
The similar burn times make it the appropriate choice for training or simulation deployment of chemical agent canisters. The Saf -Smoke formulation is considered to be less toxic than Hexachloroethane (HC) smoke. The Saf-Smoke Grenade emits a very white smoke. Part number 1063.
Quantity: 1
Purchase Price: $32.30 each
DEFENSE TECHNOLOGY SKAT SHELL 40MM MULTIPLE PROJECTILE ROUND, CS Description: The Skat Shell 40mm CS multiple chemical projectile round is designed to deliver multiple CS canisters from a 40mm launcher. It is designed for outdoor use and has a fire -producing capability and has a maximum eff ective range of 80 -100 yards. It is widely used as a crowd management tool for the rapid and broad deployment of a chemical agent by a single grenadier. The Skat Shell contains four separate sub-munitions and provides a wide area of coverage. Part number 6172.
Quantity: 97
Purchase Price: $30.12 each
CTS LC5 CHEMICAL AGENT LAUNCHING CUPS
Description: The chemical agent launching cup is affixed to the barrel end of a Remington 870 shotgun and fastened onto the barrel by a metal band and hand - tightened screw. The launching cup is utilized to hold launchable OC, CS, and smoke munitions to effectively launch them from a safe distance into the designated target area.
Quantity: 4
Purchase Price: $278.82 each
VULCAN MUNITIONS POLE
Description: The Vulcan Munition s Pole is utilized to safely deploy munitions into doors, windows, and openings of buildings and vehicles to introduce OC, CS, smoke, and diversionary devices to distract, disrupt, or incapacitate subjects barricaded in structures or vehicles. The Vulcan Munitions pole weights less than 9 pounds and is capable of extending from less than 8 feet in length to 13 feet in length.
Quantity: 2
Garden Grove Police Department
Policy Manual
Military Equipment
1794447.1
Purchase Price: $2,412.62 each
CUSTOM METAL CONCEPTS BURN SAFE
Description: The Burn Safe is a double walled container constructed of aluminum. It is designed to contain the flames inside the inner chamber thereby reducing the probability of starting a fire. The Burn Safe weighs approximately 8 pounds and is hand-deployed by officers. The weight allows the user to success fully penetrate windows, screens, and glass doors. The Burn Safe allows the introduction of significant amounts of pyrotechnic chemical agent into the target, which increases the probability of a successful resolution.
Quantity: 2
Purchase Price: $1,812.00 each
CUSTOM METAL CONCEPTS GAS RAM
Description: The Gas Ram is a multi-use tool that can be utilized for forced entry as a door ram or be deployed as a pyrotechnic Chemical Agent delivery system. The Gas Ram is equipped with a 12 inch or 24 inch metal pro be capable of penetrating walls, doors, sheet metal siding and into vehicles. Inserting the longer 24 inch probe allows use through roofs and dead air spaces. Both probes are effective in delivering significant amounts of pyrotechnic chemical agents with a minimal probability of starting fires.
Quantity: 1
Purchase Price: $1,500.00
DEFENSE TECHNOLOGY, 12 -GUAGE MUZZLE BANG/LAUNCHING CARTRIDGE ROUND
Description: The 1210 12-Gauge Muzzle Bang/Launching Cartridge incorporates an opaque shell and utilizes black powder as the propellant. It has the ability to be used alone as a Muzzle Bang for crowd management or for propelling grenades when equipped with and using a Department authorized launching cup. Part number 1210.
Quantity: 60
Purchase Price: $7.13 each
Purpose: To cause a suspect discomfort and/or deny him/her access to certain areas of a structure, vehicle, or area to aid in bringing an event to a successful conclusion. Situations for use of chemical agents may include but are not limited to:
a. To reduce violence, minimize property damage, and protect the public. b. To disperse individuals during riots or incidents of civil disobedience. c. To incapacitate a suspect who is endangering life or property.
Garden Grove Police Department
Policy Manual
Military Equipment
1794447.1
d. To apprehend suspects who refuse to submit to arrest.
Authorized Use: SWAT personnel who have been trained in the use of chemical agents.
Excepted Life Span: Refer to manufacturer’s specifications sheet for each munitions. Life span of most munitions is 5 years from date of manufacturer.
Fiscal Impact: No annual mainten ance. Munitions must be replaced per manufacturer recommendations.
Training: Sworn members utilizing chemical agents are trained in there use by POST certified chemical agent instructors.
Legal and Procedural Rules: Authorized use is established under the Use of Force Policy. It is the policy of the GGPD to utilize chemical agents only for official law enforcement purposes, and pursuant to State and Federal law regarding the use of force.
8. PEPPERBALL LAUNCHER AND ASSOCIATED MUNITIONS
A device that discharges irritant projectiles.
Current Inventory:
TIPPMANN PEPPERBALL GUN
Description: A compressed -air powered launcher designed to fire non -lethal PepperBall projectiles.
Quantity: 7
Purchase Price: $316.79 each
PEPPERBALL LIVE-X PROJECTILE
Description: The Live Projectile contains a concentrated amount of PAVA pepper powder. One round of LIVE -X contains the equivalent to 10 PepperBall rounds.
Discharged from a PepperBall Launcher, the projectile has a velocity of 280-350 FPS.
The projectile has a direct im pact of 60 ft. and an area of saturation of 150+ft. The projectile contains 5% PAVA Powder.
Quantity: 2,400
Purchase Price: $928.00/case of 375 projectiles
Purpose: To limit the escalation of conflict and decrease use of lethal force when feasible.
Situations for use of the less lethal weapon systems may include but are not limited to:
Garden Grove Police Department
Policy Manual
Military Equipment
1794447.1
a. Self-destructive, dangerous and/or combative individuals. b. Riot/crowd control and civil unrest incidents.
c. Circumstances where a tactical advantage can be obtained. d. Potentially vicious animals.
e. Training exercises or approved demonstrations.
9. 40 MM LAUNCHER AND ASSOCIATED MUNITIONS
40MM Launchers are utilized by department personnel as a less lethal tool to launch impact rounds.
Current Inventory:
DEFENSE TECHNOLOGY, 40MM SINGLE SHOT LAUNCHER
Description: The 40MM Single Launcher is a tactical single shot launcher. It will fire standard 40mm less lethal ammunition, up to 4.8 inches in cartridge length. It will launch a 40mm less lethal round up to 131 feet.
Quantity: 5
Purchase Price: $888.70 each
DEFENSE TECHNOLOGY, 40MM EXACT IMPACT SPONGE
Description: A less lethal 40mm lightweight plastic and foam projectile fired from a single or multi-round purpose built 40mm grenade launcher with a rifled barrel at 325 FPS. The 30-gram foam projectile delivers 120 foot pounds of energy on impact. The 40mm Exact Impact Sponge Round provides accurate and effective performance when fired from the approved distance of not less than five (5) feet and as far as 131 feet from the target.
Quantity: 290
Purchase Price: $20.61 each
Purpose: To limit the escalation of conflict and decrease use of lethal force when feasible.
Authorized Use: Situations for use of the less lethal weapon systems may include, but are not limited to:
a. Self-destructive, dangerous and/or combative individuals. b. Riot/crowd control and civil unrest incidents.
c. Circumstances where a tactical advantage can be obtained. d. Potentially vicious animals.
e. Training exercises or approved demonstrations.
Garden Grove Police Department
Policy Manual
Military Equipment
1794447.1
Training: Sworn members utilizing 40mm less lethal chemical agents or impact rounds are trained in there use by POST certified less lethal and chemical agent instructors.
Expected Life Span: Defense Technology Launchers - 25 years, Rounds - 5 years.
Fiscal Impact: Annual maintenance is approximately $50 for each launcher.
Legal and Procedural Rules: Authorized use is established under the Use of Force Policy. It is the policy of the Garden Grove Police Department to utilize the 40mm only for official law enforcement purposes, and pursuant to State and Federal law, including those regarding the use of force.
10. LESS LETHAL SHOTGUN AND ASSOCIATED MUNITIONS
Device used to deploy the less lethal 12-gauge Super-Sock Beanbag Round.
Current Inventory:
REMINGTON 870 LESS LETHAL SHOTGUN
Description: The Remington 870 Less Lethal Shotgun is used to deploy the less lethal 12-gauge Super-Sock Beanbag Round up to a distance of 75 feet. The range of the weapon system helps to maintain space between officers and a suspect reducing the immediacy of the threat which is a principle of de-escalation.
Quantity: 65
Purchase Price: $395.75 each
DRAG STABILIZED 12-GAUGE BEANBAG ROUND
Description: A less lethal 2.4-inch 12-gauge shotgun round firing a ballistic fiber bag filled with 40 grams of lead shot at a velocity of 270-290 feet per second (FPS). Drag Stabilized rounds are discharged from a dedicated 12 -gauge shotgun that is distinguishable by an orange butt stock and fore grip. This round provides accurate and effective performance when fired from the approved distance of not fewer than five (5) feet. The maximum effective range of this munition is up to 75 feet from the target. The Drag Stabilized Model is in its deployed state immediately upon exiting the barrel. It does not require a mini mum range to “unfold” or “stabilize.” The Drag Stabilized Model is an aerodynamic projectile. However, accuracy is relative to the shotgun, barrel length, environmental conditions, and the operator. The Drag Stabilized Model is very accurate. However, effe ctiveness depends on many variables, such as distance, clothing, stature, and the point where the projectile impacts.
Quantity: 420
Purchase Price: $6.47each
Garden Grove Police Department
Policy Manual
Military Equipment
1794447.1
Purpose: To limit the escalation of conflict and decrease use of lethal force when feasible.
Authorized Use: Situations for use of the less lethal weapon systems may include, but are not limited to:
a. Self-destructive, dangerous and/or combative individuals. b. Riot/crowd control and civil unrest incidents.
c. Circumstances where a tactical advantage can be obtained. d. Potentially vicious animals.
e. Training exercises or approved demonstrations.
Expected Life Span: Remington 870 Less Lethal Shotgun - 25 years, Drag Stabilized 12 - gauge beanbag round and Winchester slug rifle rounds - no listed expiration date.
Fiscal Impact: Annual maintenance is approximately $50 for each shotgun.
Training: All officers are trained in the 12 -gauge less lethal shotgun as a less lethal option by in -service training. SWAT personnel receive additional training internally when they transfer to the unit. SWAT operators who utilize these munitions successfully completed a POST approved gas school and/or trained in house by POST certified chemical agent instructors for muzzle blast training.
Legal and Procedural Rules: Authorized use is established under the Use of Force Policy. It is the policy of the Garden Grove Police Department to utilize the less lethal shotgun only for official law enforcement purposes, and pursuant to State and Federal law, including those regarding the use of force.
11. WINCHESTER SEGMENTED SLUG RIFLED ROUNDS
Description: Winchester 12-gauge 2.75-inch segmented shotgun rifles slugs features full bore rifling, so they will have improved accuracy and sectional density when fired out of a smooth bored shotgun. The round segments upon impact as to not over penetrate barriers.
Quantity: 3,500
Purchase Price: $746.00/1,000 round
Purpose: To be used as precision weapons to address a threat with more precision and/or greater distances than a handgun, if present and if use is feasible. This is a standard issued patrol duty round.
Authorized Use: All sworn officers who have graduated from a POST Academy are authorized to use this ammunition.
Expected Life Span: No expiration date.
Fiscal Impact: Annual training with qualification is approximately $947.05.
Garden Grove Police Department
Policy Manual
Military Equipment
1794447.1
Training: Officers must be certified by POST instructors (standard POST Academy trained) in the operation of the shotgun . Additionally, al l members that operate any shotgun are required to pass a range qualification one time a year.
Legal and Procedural Rule: It is the policy of the Garden Grove Police Department to utilize rifles only for official law enforcement purposes, and pursuant to State and Federal law regarding the use of force.
Garden Grove Police Department
Policy Manual
Military Equipment
1794447.1
Agenda Item - 4.c.
City of Garden Grove
INTER-DEPARTMENT MEMORANDUM
To: Lisa Kim From: Ursula Luna-Reynosa
Dept.: City Manager Dept.: Economic Development and
Housing Department
Subject: Authorize the appropriation of
the Encampment Grant
Resolution Funding Round 3
Lookback (ERF-3-L), and
authorize the City Manager to
execute a Memorandum of
Understanding with the
County of Orange. (Cost:
$1,921,500) (Action Item)
Date: 10/24/2023
OBJECTIVE
Authorize the appropriation of the Encampment Grant Resolution Funding Round 3 Lookback (ERF-3-L) (Cost: $1,921,500), and authorize the City Manager to execute a Memorandum of Understanding with the County of Orange ( Action Item)
BACKGROUND
On December 1, 2022, the California Interagency Council on Homelessness (CalICH) released a $237,301,738 Notification of Funding Availability (NOFA) for the second disbursement of the Encampment Resolution Funding Grant Program. This initiative is dedicated to addressing unsheltered homelessness; focusing on the safety, well-being, and housing solutions for individuals residing in encampments. This grant prioritizes activities with clear pathways to permanent housing or directly into permanent housing, using data-informed, non-punitive, low-barrier, person-centered, Housing First, and coordinated approaches.
On February 28, 2023, staff submitted a funding proposal amounting to approximately $3.4 million with the intent to deploy resources to assist homeless encampment individuals at four (4) homeless encampment sites in Garden Grove along the 22 Freeway: 1) Beach Blvd., 2) Euclid St., 3) Newhope St., and 4) Haster St. The proposed allocation of funds was intended to support the Navigation Center operations, bolster street outreach efforts, enhance data collection through the Homeless Management Information System (HMIS), and contribute to the Caltrans Fencing Improvement Project.
DISCUSSION
On June 30, 2023, staff re-submitted a funding proposal totaling $1,921,500, targeting
On June 30, 2023, staff re-submitted a funding proposal totaling $1,921,500, targeting resource allocation to the Beach Blvd. homeless encampment. This encampment was selected due to its substantial size, high population density, rapid influx of transient individuals, and a significant volume of emergency service calls and incidents of violent criminal activity. On September 12, 2023, the City received the full amount of $1,921,500 from the CalICH.
The City intends to allocate the awarded amount of $1,921,500 to enhance the operations of the Navigation Center and to expand street outreach efforts in close coordination with the Garden Grove Police Department Special Resource Team (SRT), BeWell OC Mobile Response Unit, and the County of Orange Office of Care Coordination. $330,000, of the $1,921,500, will be designated to the County for street outreach, individualized support, and case management for chronic homeless individuals residing in the Beach Blvd encampment.
FINANCIAL IMPACT
There is no fiscal impact on the General Fund. The Encampment Resolution Funding Grant (ERF-3-L) Program does not require a match from the City.
The budget summary is as follows:
Services FY 24-25 FY 25-26 FY 26-27
Low-barrier Navigation Center Operations $ 500,000.00 $0.00 $0.00 Special Resource Team (SRT) $ 150,000.00 $ 150,000.00 $150,000.00 OC Office Care Coordination $ 165,000.00 $ 165,000.00 $0.00 BeWell OC Mobile Response Team $ 200,000.00 $ 175,000.00 $ 175,000.00 Total Cost (FY 24-25, 25-26, 26-27) $1,830,000.00
Administrative Cost (5%) $91,500.00
Total Requested Amount $1,921,500.00
RECOMMENDATION
It is recommended that the City Council:
Authorize the Finance Director to appropriate the ERF-3-L awarded amount, not to exceed $1,921,500;
Authorize the City Manager, or her designee(s), to execute a Memorandum of Understanding (MOU) between the County of Orange and the City, and make minor modifications as appropriate thereto including the provision of $330,000 in funding, on behalf of the City; and
Authorize the City Manager, or her designees, to execute any agreements and amendments related to the ERF-3-L or MOU.
By: Christy Le, Homeless Liaison Analyst
•
•
•
ATTACHMENTS:
Description Upload Date Type File Name
ERF-3-L Award Letter 10/13/2023 Cover Memo ERF-3-
L_Award_Letter_City_of_Garden_Grove.pdf
CAL ICH
September 2023
California
lnteragency Council
on Homelessness
City of Garden Grove
Attn: Lisa Kim
11222 Acacia Pkwy
Garden Grove, CA 92840
RE: Award Announcement - City of Garden Grove #23-ERF-3-L- 00004
Award Amount: $1,921,500.00
Dear Lisa Kim:
The Business, Consumer Services and Housing Agency's (BCSH) California Interagency Council on Homelessness (Cal ICH) is pleased to announce that the City of Garden Grove has been awarded an Encampment Resolution Funding Round 3 Lookback (ERF-3-L) grant in the amount of $1,921,500.00. This letter constitutes notice of the award of ERF-3-L funds for use in the City of Garden Grove.
The City of Garden Grove will receive its full disbursement of funds after the Standard Agreement is fully executed. Please be advised that this award is subject to the terms and conditions of the Standard Agreement. Failure to sign and return the Standard Agreement within 30 days ofreceipt from BCSH may result in a delay of disbursement of funds.
Congratulations on your successful application. For further information or if you have any questions, please contact me at [email protected] or [email protected] .
Sincerely,
~e,7'1c,~~
Jeannie McKendry,
Grants Development Section Chief, Cal ICH
BUSINESS, CONSUMER
SERVICES AND
HOUSING AGENCY
Gavin Newsom,
Governor
Lourdes M.
Castro Ramirez,
Secretary
801 Capitol Mall
Suite 601
Sacramento, CA 95814
(916) 651-2820
bcsh.ca.gov/calich
Agenda Item - 4.d.
City of Garden Grove
INTER-DEPARTMENT MEMORANDUM
To: Lisa L. Kim From: William E. Murray
Dept.: City Manager Dept.: Public Works
Subject: Authorize the issuance of a
purchase order to PB Loader
for one (1) new Police
Department Command Post.
(Cost: $1,199,660.40)
(Action Item)
Date: 10/24/2023
OBJECTIVE
To secure City Council authorization to purchase one (1) new Police Department command post from PB Loader through the Sourcewell competitive bid program, Contract #080521-PBL.
BACKGROUND
The Public Works Department has one (1) Police Department command post that currently meets the City’s guidelines for replacement. Funding for the replacement was approved in the FY 2023-24 Fleet Management Fund's budget. The vehicle being replaced is a 2007 Freightliner LDV command post with 6,100 miles VIN# 4UZAASBV17CX75529.
DISCUSSION
Experience has shown that the City’s buying power is enhanced through joining with other public agencies to purchase fleet vehicles and equipment. Sourcewell nationally solicits, evaluates, and awards contracts through a competitive bid process. As a member of Sourcewell, the City is able to utilize bid awards for equipment purchases. Staff recommends piggybacking on the results of a recent Sourcewell competitive bid program, Contract #080521-PBL. The results deemed PB Loader as the lowest responsive bid.
PB Loader $1,199,660.40*
* This price includes all applicable tax and destination charges.
FINANCIAL IMPACT
The cost of replacing the vehicle is $1,199,660.40, and is included in the the Fleet Management Fund's Fiscal Year 2023-24 budget. There is no impact to the General Fund. The surplus equipment will be sold at public auction.
RECOMMENDATION
It is recommended that the City Council:
Authorize the Finance Director to issue a purchase order in the amount of $1,199,660.40 to PB Loader for the purchase of one (1) new Police Department Command Post.
By: Steve Sudduth, Equipment Maintenance Supervisor ATTACHMENTS:
Description Upload Date Type File Name
PB Loader quote 10/11/2023 Backup Material PB_Loader_command_post_quote.pdf Command post specs 10/11/2023 Backup Material Command_Post_specs.pdf
•
PB Loader Corporation
5778 W. Barstow • Fresno, California 93722-5024 • Telephone (559) 277-7370 • Fax (559) 277-7375 Toll free 800-350-8521 • Web www.pbloader.com
QUOTATION
CITY OF GARDEN GROVE - POLICE DEPARTMENT
GARDEN GROVE, CA DATE: 10/5/2023
SOURCEWELL MEMBER ID # 32278 TERMS: NET 30
PROJECT: 26FT MOBILE COMMAND CENTER
QTY PART NO. DESCRIPTION PRICE EXTENSION
PB LOADER CONTRACT NO. 080521-PBL
SOURCEWELL CONTRACT - LISTED PRICES
26FT MOBILE COMMAND CENTER
1 26FT_MCC $1,225,707.00
10% SOURCEWELL DISOUNT: ($122,571.00)
SUB-TOTAL: $1,103,136.00
SALES TAX (8.75%): $96,524.40
TIRE FEE: $10.50
TOTAL PRICE PER UNIT: $1,199,660.40
NOTES:
NO. 11958R
LDV MOBILE COMMAND CENTER 26’ WALK-IN VAN BODY BUILT ON A FREIGHTLINER MT55 FRONT ENGINE WALK-IN VAN CHASSIS WITH:
• 250" WHEELBASE • 431” OVERALL LENGTH OF APPARATUS • 99” OVERALL APPARATUS WIDTH, RUB RAIL TO RUB RAIL • 142” OVERALL HEIGHT OF APPARATUS (LOADED) • 83” RAW INTERIOR WALKWAY HEIGHT • 81.5’ FINISHED INTERIOR WALKWAY HEIGHT • 312” INTERIOR WALKWAY LENGTH • 96” RAW INTERIOR WIDTH • 87” INTERIOR FINISHED WIDTH • CUMMINS B6.7 260HP @ 2400 RPM DIESEL ENGINE • ALLISON 2200 EVS AUTOMATIC TRANSMISSION WITH PARK PAWL WITH PTO PROVISION • DA-RS-17.5-2 17,500# L-SERIES SINGLE REAR AXLE • 18,000# AIRLINER REAR SUSPENSION • DA-F-10.0-3 10,000# FF1 69.0 KPI/3.50DROP SINGLE FRONT AXLE • 10,000# TAPERLEAF FRONT SUSPENSION • 60 GALLON RECTANGULAR STEEL FUEL TANK - BETWEEN RAILS • MICHELIN 255/70R22.5 16 PLY RADIAL TIRES • MAXION STEEL DISC WHEELS • FEDERAL SIGNAL BACK-UP ALARM MODEL 210331 • US DOT TRIANGLE REFLECTOR KIT WITH THREE (3) TRIANGLES • CLASS III RECEIVER HITCH (BALL MOUNT AND BALL NOT INCLUDED) • REESE BRAKEMAN® IV DIGITAL ELECTRONIC TRAILER BRAKE CONTROL • 7 POLE BLADE STYLE TRAILER CONNECTOR • FRONT FRP BULKHEAD WALL BEHIND FRONT DRIVER AND PASSENGER SEATS. • SAMSUNG FLIP 2 WM65R 65 INCH DIGITAL WHITEBOARD • IRIDIUM 9575 EXTREME DOCKING STATION • RJ-45 CAT6 COMPUTER NETWORK FOR THREE (3) WORKSTATIONS, ONE (1) PRINTER, TWO (2) PASSENGER SEAT AREA, TWO (2) EXTERIOR TO TV COMPARTMENT, TWO (2) IN EXTERIOR INPUT BOX.
1. SEE FULL SPECIFICATOINS FOR FULL DESCRIPTION OF COMMAND CENTER.
2. PAYMENT TERMS ARE 50% DOWN PAYMENT, 50% NET 30.
3. QUOTE IS FIRM FOR 30 DAYS FROM DATE ABOVE.
4. THE QUOTED PRICE DOES NOT INCLUDE ANY APPLICABLE FET.
5. TRAILER HITCH IS RATED FOR 5,000 LBS; HOWEVER, TOWING CAPACITY IS LIMITED TO MAXIMUM VEHICLE GROSS COMBINED WEIGHT RATING (GCWR).
6. FINAL MEASUREMENTS ARE DEPENDENT ON BODY BUILDER, CHASSIS COMPONENTS, AXLES, TIRES, FRAME, SUSPENSION, AND ROOF-MOUNTED EQUIPMENT.
\
\
180 Industrial Drive
Burlington, WI 53105 USA
Phone: 800-558-5986
Fax: (262) 767-2529
Direct: +1 (262) 763-0147
www.ldvusa.com
PRELIMINARY
SPECIFICATIONS FOR:
GARDEN GROVE PD (CA)
(VELOCITY TRUCK CENTER)
MOBILE COMMAND CENTER
LDV PROPOSAL # S36MCC-35686-23
August 21, 2023
SEPTEMBER 15, 2023 REV 1
LDVJ)
CUSTOM SPECIALTY VEHICLES
Garden Grove PD (CA) S36MCC-35686-23 CC REV 1
180 Industrial Drive
Burlington, WI 53105 USA
Phone: 800-558-5986
Fax: (262) 767-2529
Direct: +1 (262) 763-0147
www.ldvusa.com
TABLE OF CONTENTS
PRICING PAGE: .........................................................................................................................................................3 CHASSIS: ...................................................................................................................................................................4 BODY: .........................................................................................................................................................................4 PAINT / GRAPHICS: ..................................................................................................................................................7 DRIVER / PASSENGER CAB AREA: ........................................................................................................................8 WALLS, CEILING AND FLOOR: ................................................................................................................................8 GALLEY: .....................................................................................................................................................................9 SEATING: ...................................................................................................................................................................9 CABINETS: .............................................................................................................................................................. 10 HVAC SYSTEM: ...................................................................................................................................................... 11 AC ELECTRICAL SYSTEM: .................................................................................................................................... 11 DC ELECTRICAL SYSTEM: ................................................................................................................................... 15 EMERGENCY LIGHTING / SIRENS: ...................................................................................................................... 17 AUDIO / VIDEO: ...................................................................................................................................................... 18 MAST AND MAST MOUNTED EQUIPMENT: ........................................................................................................ 20 RADIOS: .................................................................................................................................................................. 21 COMPUTER NETWORK AND EQUIPMENT: ........................................................................................................ 22 MISCELLANEOUS ELECTRONICS: ...................................................................................................................... 23 EXTERIOR STORAGE COMPARTMENTS: ........................................................................................................... 23 MISCELLANEOUS OTHER: ................................................................................................................................... 24
LDVJ)
CUSTOM SPECIALTY VEHICLES
Garden Grove PD (CA) S36MCC-35686-23 CC REV 1
180 Industrial Drive
Burlington, WI 53105 USA
Phone: 800-558-5986
Fax: (262) 767-2529
Direct: +1 (262) 763-0147
www.ldvusa.com
Delivery terms: Ask your Sales Representative.
Payment Terms: 50% down payment, 50% net 30.
Quote is firm for 30 days from specification date.
Quoted price does not include any applicable FET, federal, state or local tax unless specified.
LDVJ)
CUSTOM SPECIALTY VEHICLES
180 Industrial Drive
Burlington, WI 53105 USA
Phone: 800-558-5986
Fax: (262) 763-0156
Direct: +1 (262) 763-0147
www.ldvusa.com
Item Qty
Garden Grove PD (CA) S36MCC-35686-23 CC REV 1
1.00 CHASSIS/BODY DIMENSIONS:
26’ walk-in van
• Wheelbase of chassis: 250"
• Overall length of apparatus: 431"
• Overall apparatus width, rub rail to rub rail: 99"
• Overall height of apparatus (loaded): 142"
• Interior walkway height raw body: 83"
• Interior walkway height finished: 81.5"
• Interior walkway length: 312"
• Interior raw body width: 96"
• Interior finished body width: 87"
Final measurements are dependent on body builder, chassis components, axles, tires, frame, suspension, and roof-mounted equipment.
2.00 CHASSIS:
2.01 1 Customer supplied chassis check in.
Test all chassis equipment before any upgrades are done. - Interior and exterior, structure, locks, lights, electronics, batteries, as applicable. - Chassis fluid levels, batteries
2.02 1 Federal Signal Back-up alarm model 210331.
2.03 1 US DOT triangle reflector kit with three (3) triangles, for compliance with FMCSA regulations.
Includes plastic storage case. Kit will be shipped loose in the vehicle.
2.04 1 Custom fabricated Class III receiver hitch (ball mount and ball not included). Includes:
• Reese Brakeman® IV digital electronic trailer brake control • 7 pole blade style trailer connector.
Note: Trailer hitch is rated for 5,000 lbs; however, towing capacity is limited to maximum vehicle Gross Combined Weight Rating (GCWR).
2.05 1 Stainless steel wheel liners with braided stainless steel valve stem extenders.
2.06 1 Route horizontal exhaust to streetside.
3.00 BODY:
3.01 1 • Load space area shall be 83" high x 96" wide x 26' long all aluminum step van body. • Driver sedan door with slider window, door skin shall be chemically bonded to door frame structure reducing the amount of rivets required. Door shall have continuous stainless steel piano hinge and two (2) nylon straps.
• Passenger sedan door with slider window, door skin shall be chemically bonded to door frame structure reducing the amount of rivets required. Door shall have continuous stainless steel piano hinge and two (2) nylon straps.
• Sedan doors shall have a 0.125" aluminum tread plate step well for 18" skirt depth. • Sedan doors shall have black non-skid tape on all door entry sills. • Sedan doors shall have polished aluminum TriMark flush mounted locking hardware with self - aligning rotary latch and matching key locks. Outside door handles not to exceed 50" from ground.
LDV@
CUSTOM SPECIALTY VEHICLES
180 Industrial Drive
Burlington, WI 53105 USA
Phone: 800-558-5986
Fax: (262) 763-0156
Direct: +1 (262) 763-0147
www.ldvusa.com
Item Qty
Garden Grove PD (CA) S36MCC-35686-23 CC REV 1
• Aluminum alloy double H wall beam, 6005-T5 alloy, 3" x 3" wide at the base, 1.5" wide at the top, 0.125 wall thickness. Studs feature machined wire pass-throughs, and raised adhesive control features on base.
• I-beams shall be chemically bonded to sidewalls eliminating the need for additional rivets.
Buck-rivets will be used to fasten the top, bottom and rub rail. Use of two-sided tape is not acceptable.
• Body shall have 0.125" strain-hardened aluminum alloy 5052-H36 side panels. The upper panels shall be free of rivets allowing for smooth graphics application. • Skirt supports,1.5 x 1.5 x 0.125 angle to reinforce skirt edge and hold bottom edge in a straight line. 0.188 x 1.00" flat braces placed at 4' intervals and riveted to lower wall angle and floor to maintain sidewall skirt rigidity.
• NFPA 1901 embossed 0.125" aluminum tread plate roof attached to 3" x 1 1/2" x 0.125" extruded aluminum roof bows on 16" centers. Bows are 2” skip welded every 12”. Tread plate seams shall be continuous welded. Perimeter of roof shall be chemically sealed . • Lift-up molded fiberglass hood with chrome grill insert. Hood shall have integrated headlamps and turn signal indicators and dual assist gas charged lift shocks. The use of mechanical assist springs is not acceptable.
• Extruded aluminum floor with interlocking planks, 1.88" high x various widths, 0.125" top surface. 6005-T5 alloy and temper. Heavy-duty thick-wall extruded planks fore and aft of all floor cutouts and every 5th plank in all other areas. Planks made of 6005-t5 alloy and temper,
0.250" thick top surface.
• Bright polished front bumper.
• Tinted safety plate glass windshield with driver and passenger sun visors. • Full width 12" deep heavy-duty aluminum rear bumper with center step, painted to match the body.
• Integral cab air conditioning and heating system with dash controls. • Velvac heated remote control rear view mirrors with dash controls. Upper mirror has 62 -sq.in. of flat surface and lower mirror has 30-sq.in. of convex surface. Mirror has a fold-away arm. • Driver seat shall be Seats Inc. Magnum 200 mechanical suspension seat on fixed pedestal.
Seat shall be covered in black cloth and have arm rests, lumbar support, tilt back and 3 -point seat belt.
• Passenger seat shall be black jump seat with 2-point seat belt. • Intermittent windshield wiper/washer with single heavy-duty windshield wiper motor. • Custom front wheel cutouts for tires.
• Aluminum engine box cover with acoustical and thermal insulation. • Acoustical and thermal insulation with heat shield on exterior fire-wall. • Full length skirting. Skirt shall extend 18” down from the bottom of floor extrusions. • All clearance and side marker lights to be LED.
• Standard structural warranty of 5 years or 50,000 miles and standard component warranty of 12 months or 12,000 miles.
• The vehicle shall be fully sanded on all exterior surfaces with no more than 150 grit to assure removal of imperfections in metal surface. All aluminum shall be chemically etched and primed prior to painting. Base body color shall be oven baked and painted to commercial truck standards.
LDV@
CUSTOM SPECIALTY VEHICLES
180 Industrial Drive
Burlington, WI 53105 USA
Phone: 800-558-5986
Fax: (262) 763-0156
Direct: +1 (262) 763-0147
www.ldvusa.com
Item Qty
Garden Grove PD (CA) S36MCC-35686-23 CC REV 1
Note: Specifications are from body manufacturer and are subject to change without notice.
3.02 1 32" wide x 82" high 0.125" aluminum sedan door with 21.5" wide x 25.5" high fixed window.
Door shall have continuous stainless steel piano hinge, two (2) nylon door st raps and an aluminum drip rail.
NOTE:
Interior window covering will be a mini blind.
3.03 3 Exterior heavy-duty knurled aluminum grab handle with chrome plated stanchions, installed at entry door.
3.04 1 Interior heavy-duty knurled aluminum grab handle with chrome plated stanchions, installed at entry door.
3.05 3 Automatic LED courtesy light at entry door.
3.06 1 Courtesy light defeat in Intel-I-Touch™ multiplex control screen. Each entry door courtesy light will be automatically deactivated where the corresponding room has the overhead lighting set to night mode.
3.07 1 Lippert Treadlite 24" wide - single - automatic electric steel entry step mounted under entry door. Product features:
• Automatic LED ground light
• Hold/Cycle switch that allows step to remain extended unless ignition is turned on.
NOTE:
Step light will be tied into courtesy light defeat.
3.08 1 Lippert Treadlite 30" wide - single - automatic electric steel entry step mounted under entry door. Product features:
• Automatic LED ground light
• Hold/Cycle switch that allows step to remain extended unless ignition is turned on.
NOTE:
Step light will be tied into courtesy light defeat.
3.09 1 Whelen Stop/Turn/Tail/Backup light set. Includes two of each of the following:
• Whelen M6FCV4 polished chrome vertical housings for four M6 series lightheads. The fourth light head will be an emergency flasher as specified in the DC Emergency Lighting section. • Whelen M6 series LED arrow shaped amber turn signal, model number M62T. • Whelen M6 series LED brake/tail light heads, model number M62BTT. • Whelen M6 series LED back-up light heads, model number M62BU.
3.10 1 Cast Products LP0004-1-B aluminum license plate mounting frame with LED light.
3.11 1 Entire underside shall be undercoated. Includes floor extrusions, step wells and aluminum compartments.
3.12 1 LDV rear mud flaps. Includes anti-sail brackets when required.
3.13 2 Flat floor slide-out room extension fabricated with a structurally rigid welded aluminum tube design with a fully bonded aluminum shell. During deployment an electronic control system automatically expands the room extension and lowers the floor to flush position.
Features:
• Electric over hydraulic control system programmed to lower the slide out to floor height after full extension.
LDV@
CUSTOM SPECIALTY VEHICLES
180 Industrial Drive
Burlington, WI 53105 USA
Phone: 800-558-5986
Fax: (262) 763-0156
Direct: +1 (262) 763-0147
www.ldvusa.com
Item Qty
Garden Grove PD (CA) S36MCC-35686-23 CC REV 1
• Awning that automatically extends and retracts over the top of the room to protect from weather and debris.
• Full perimeter double rubber bulb seal with an additional seal in the fully extended and fully retracted positions.
• No track or hardware shall be attached to the ceiling of the body.
NOTE:
Slide out up to 96" length x 30" deep (full extension of 26").
3.14 Ignition Interlock to prevent vehicle from starting when any of the external extension devices are deployed.
3.15 4 Flashing warning light for slide out.
NOTE:
Amber LED color.
4.00 PAINT / GRAPHICS:
4.01 Body base color shall be white.
4.02 Body base paint shall be a commercial single stage white color.
4.03 1 4-inch wide reflective stripe on the exterior back and sides of the vehicle.
4.04 1 Custom computer-generated non-reflective vinyl graphics per customer specifications.
Includes up to seventy 8"-10" letters and up to forty-five 3"-6" letters. All lettering can be shaded or outlined.
4.05 5 Custom computer-generated non-reflective vinyl shield. Customer shall supply true vector artwork required to produce shield.
NOTE:
Customer is to supply vector file format artwork (ai, .eps True Vector File) to LDV to produce graphics. LDV will provide printing, material and install of graphics.
5.00 INTERIOR:
• Wall Covering Front/Rear rooms: Chrome carpet
• Wall Covering Middle room: Wilsonart laminate Satin Stainless 483 • Bulkheads - Wilsonart laminate Satin Stainless 483
• Control console cabinet – Black laminate
• Ceiling:
o Center (ductwork) #HAT2-C0111 Charcoal Gray Texture Powder Coated o Outside Silver Mist carpet
• Trim: #HAT2-C0111 Charcoal Gray Texture Powder Coated • Floor Covering: #150 Onyx PVC Flooring
• Office Chairs: Black
• Cabinets: #HAT2-C0111 Charcoal Gray Texture Powder Coated Aluminum • Powdercoat color for slideout valance and interior door panel o #HAT2-C0111 Charcoal Gray Texture Powder Coated
• Vinyl/fabric coverings:
o Seat bottom to be stock Black Vinyl.
o Seat back to be Ultraleather Dwell 570-5635 Basalt back • Counters and Tables: #4879-38 Steel Mesh Laminate with GRAY T-molding Note: Manufacturer reserves the right to substitute equivalent materials.
LDV@
CUSTOM SPECIALTY VEHICLES
180 Industrial Drive
Burlington, WI 53105 USA
Phone: 800-558-5986
Fax: (262) 763-0156
Direct: +1 (262) 763-0147
www.ldvusa.com
Item Qty
Garden Grove PD (CA) S36MCC-35686-23 CC REV 1
6.00 DRIVER / PASSENGER CAB AREA:
6.01 1 Walk-in van custom cab area finishing.
• Cover cab doors with aluminum panels powder coated.
• Heavy-duty rubber grab handle on each door.
• Panels covered with vinyl or fabric above driver and passenger doors. • Vehicle height sign on dash.
• Insulated black rubber mat in driver and passenger toe plate area. • Insulate walls in kick plate area and install black carpeted panels. • Vehicle shall have a Final Stage Vehicle Certification and Altered Vehicle Certification as required by Federal Motor Vehicle Safety Standards (FMVSS) 49 CFR Part 567.5 and 567.7 • Payload sticker in cab area with vehicle axle load ratings and available axle payload as built.
6.02 1 Work area on passenger side covered with laminate to match rear countertops and trimmed with vinyl T-molding.
6.03 1 Custom fabricated console to house electrical distribution components and control panels shall be located in the overhead console above the windshield. The entire console shall be constructed of 3/4" plywood. The face shall be finished with laminate the bottom shall be covered with vinyl.
6.04 1 Red/Clear LED dome light with 3-position switch, red/off/white.
6.05 1 Brigade Backeye 360 Select surround surveillance system with 7" LCD monitor.
6.06 1 AM/FM stereo with Bluetooth and one (1) pair of 6" x 9" speakers.
6.07 1 Blackout curtains with magnetic securement for all cab area windows. Curtain specs:
• Woven fabric made of pigmented and acrylic top coated 45% polyester / 55% cotton fabric • Tensile Strength: 283 lbs. x 214 lbs.
• Manufacturer's 5-year limited warranty
• Seams shall be double stitch/single fold
• Meets California State Fire Marshall requirements for flame retardancy - Title 19, CPAI-84 (Section 6), and FMVSS-302
NOTE:
Blackout curtain color will be Grey
7.00 WALLS, CEILING AND FLOOR:
7.01 Insulate walls with a minimum of 2-1/2" of fiberglass insulation. Cover interior body side posts with 1/2" plywood sub wall.
7.02 Cover sub wall with ribbed loop pile carpet.
7.03 Cover sub wall with Wilsonart laminate.
7.04 Insulate ceiling with a minimum of 2-1/2" of fiberglass with an R-11 rating. • Cover interior roof beams with 1/2" plywood.
• Modular panel design allows for manageable future additions and repairs . • Plywood Panels covered in acoustical fabric.
7.05 Floor underlayment to be 5/8" exterior grade tongue and groove structural plywood, 6 ply, face veneer plugged and sanded.
LDV@
CUSTOM SPECIALTY VEHICLES
180 Industrial Drive
Burlington, WI 53105 USA
Phone: 800-558-5986
Fax: (262) 763-0156
Direct: +1 (262) 763-0147
www.ldvusa.com
Item Qty
Garden Grove PD (CA) S36MCC-35686-23 CC REV 1
7.06 Lonseal Loncoin II Flecks non-skid commercial grade PVC flooring. The flooring shall be continuous, one piece full length, full width, no seams.
7.07 Vinyl cove molding (mop board) at base of wall, 2-1/2” high. Installed where required.
7.08 2 Flush pocket door installed on heavy-duty aluminum c-channel track with two (2) three-wheel roller trucks and soft open/close feature. Pocket door shall have recessed handle and magnetic closure to keep the door open/closed.
7.09 All bulkheads shall be covered with materials to match walls. Trim exposed edges of bulkheads with rounded anodized aluminum trim where applicable.
7.10 1 Cover load space door with powder coated aluminum panel with heavy-duty rubber grab handle.
NOTE:
Interior window covering will be a mini blind.
7.11 1 Hehr Street side mounted 36" wide x 24" high flush mount deep-tint horizontal sliding egress window with screen.
NOTE:
Interior window covering will be a mini blind.
8.00 GALLEY:
8.01 1 Microwave oven, minimum 1.0 cu. ft..1000-watt.
NOTE:
Current model is Panasonic NN-SU656B 1.3 Cu. Ft. Black Countertop Microwave Oven
8.02 1 KEURIG K-Duo Plus Single Serve & Carafe Coffee Maker • 12 Cup Thermal Carafe
• Use Ground Coffee or KCup & Reg Pods
• 14.19" H x 7.68" W x 15.88" D (17.5” top is open)
8.03 1 Norcold model DE105 12Vdc/120Vac combination refrigerator/freezer. Features:
• 3.3-cu.ft. capacity
• Two white powder-coated wire shelves with raised lip
• Dual clear door bins
• LED interior light
9.00 SEATING:
9.01 6 Space Air Grid office chair 5560 black with armrests, five caster spider base, and adjustable height.
9.02 6 Securement strap with buckle installed under counter to secure office chair.
9.03 1 Upgrade from passenger Jump Seat to a Magnum 200 mechanical suspension seat on fixed pedestal. Seat shall be covered in black cloth and have arm rests, lumbar support, tilt back and 3-point seat belt.
9.04 Fabricate and install fixed bench seating with removable cushions as shown on drawing.
Bench seat cushions shall be covered in heavy-duty vinyl.
9.05 BENCH SEAT REQUIREMENTS:
• Foam for seat backs and bottoms shall be firm density. • All bench seating material must meet Federal Motor Vehicle Safety Standards part 571.302 Flammability of Interior Materials.
• Material corners shall be squared or angled to fit precise cut of foam.
LDV@
CUSTOM SPECIALTY VEHICLES
180 Industrial Drive
Burlington, WI 53105 USA
Phone: 800-558-5986
Fax: (262) 763-0156
Direct: +1 (262) 763-0147
www.ldvusa.com
Item Qty
Garden Grove PD (CA) S36MCC-35686-23 CC REV 1
• Foam shall be bonded to plywood backer with industrial grade adhesive. • Attachment of fabric/vinyl to backer shall utilize industrial grade upholstery staples.
10.00 CABINETS:
10.01 Custom fabricated aluminum cabinets located as shown on drawing. Cabinet specifications:
• Base cabinets constructed of 0.080" powder coated aluminum with anodized aluminum frames.
• Base cabinet doors are double shell, formed from a single sheet of 0.080" aluminum, with a
0.040" aluminum door back attached.
• Overhead cabinets constructed of 0.064"powder coated aluminum with anodized alum inum frames.
• Overhead cabinet doors are double shell, formed from a single sheet of 0.064" aluminum, with a 0.040" aluminum door back attached.
• Overhead cabinet doors swing up with gas spring lift supports.
10.02 4 Dry erase writing surface on overhead cabinet door.
10.03 1 LED light with on/off switch, mounted under overhead cabinet.
NOTE:
Galley
10.04 7 Key lock on drawer.
10.05 4 Key lock on cabinet door.
10.06 1 Slide-out printer tray.
10.07 8 Magnetic dry erase board framed in aluminum. Includes aluminum clip frame for easy board replacement, sized as required.
NOTE:
Locate:
(1) Each Street side slide out, side walls
(1) Each on Curb side slide out, side walls
(1) Street side, front facing pocket door bulk head
(1) Curb side, front facing pocket door bulk head
(2) Rear room, Street side above bench seating
(1) Rear room, rear wall
10.08 1 Cut behind framed white dry erase board
10.09 4 FRP shelf up to 24” wide with 2" lip at front edge.
10.10 1 Aluminum box pan shelf up to 36” wide.
NOTE: Shelf for UPS above printer
10.11 Closet shelves shall be infinitely adjustable using mini B-line track and hardware.
NOTE: Street side closet
10.12 Countertops shall be covered in 0.040" Wilsonart laminate. All exposed edges shall be covered with heavy duty flexible PVC T-molding.
10.13 Removable table covered in 0.040" Wilsonart laminate. All exposed edges shall be covered with heavy duty flexible PVC T-molding.
10.14 6 Computer cable pass-thru grommet in counter.
10.15 1 Install a key display board inside overhead cabinet and clearly tag all keys for the vehicle as to their purpose.
LDV@
CUSTOM SPECIALTY VEHICLES
180 Industrial Drive
Burlington, WI 53105 USA
Phone: 800-558-5986
Fax: (262) 763-0156
Direct: +1 (262) 763-0147
www.ldvusa.com
Item Qty
Garden Grove PD (CA) S36MCC-35686-23 CC REV 1
NOTE:
Ship Loose
11.00 HVAC SYSTEM:
11.01 1 Fan-tastic Vent model 1450 3-speed reversible 12" power roof ventilator.
11.02 4 Ducted low profile rooftop air conditioner controlled through multiplex control system. Includes:
• 13,500 nominal Btu/hr air conditioner with condensate pump. • Chill Grille Assembly with 6,000 Btu/hr heat strip
• Louvered Ceiling Vents, as required
NOTE:
Locate:
(2) Front Room
(1) Middle Room
(1) Rear room
11.03 2 Broan model 174 wall mount 5,120 Btu/hr electric heater.
NOTE:
(1) Front room
(1) Rear room
12.00 AC ELECTRICAL SYSTEM:
12.01 1 Power Tech 20-kW 120/240Vac liquid-cooled diesel generator with air bag mounts installed in a custom fabricated compartment. Generator features:
• Tier 4F Emissions
• USTC Certified Manufacturer
• Warranty: 2 years from date of purchase, or 3000 hours whichever comes first, or 36 months from the date of manufacture.
• Four point air bag mounting system
• Four-cycle water cooled diesel engine
• Radiator cooled, direct mounted
• High-coolant temp and low oil pressure shutdown sensors • Spin-on fuel and oil filter
• Single side service
• Typical Gallon Per Hour fuel consumption: 25% load = 0.45, 50% load = 0.90, 100% load =
1.80 Compartment shall be constructed to the following specifications:
• 0.187" aluminum with all welded seams.
• 2" deep 0.125" aluminum box pan doors and 0.125" aluminum frames. • Door frames riveted to the body and welded to the compartments. • Stainless steel door hinges attached with stainless steel machine screws. • Flush mounted door handles with slam latches.
• 0.100" aluminum treadplate panels on interior door surfaces. • Gas charged lift/support cylinders to hold doors open at 90°. • Industrial grade neoprene gasket door seals.
NOTE:
LDV@
CUSTOM SPECIALTY VEHICLES
180 Industrial Drive
Burlington, WI 53105 USA
Phone: 800-558-5986
Fax: (262) 763-0156
Direct: +1 (262) 763-0147
www.ldvusa.com
Item Qty
Garden Grove PD (CA) S36MCC-35686-23 CC REV 1
Generator exhaust shall be routed to the street side of the vehicle.
LDV@
CUSTOM SPECIALTY VEHICLES
180 Industrial Drive
Burlington, WI 53105 USA
Phone: 800-558-5986
Fax: (262) 763-0156
Direct: +1 (262) 763-0147
www.ldvusa.com
Item Qty
Garden Grove PD (CA) S36MCC-35686-23 CC REV 1
12.02 1 ACData surge suppressor for protection of entire AC power system.
Product features:
• UL listed: UL1449 3rd Edition
• LED visual verification of status
12.03 1 LDV exclusive Intel-I-Touch™ vehicle automation control system.
A multiplexed vehicle automation system must be incorporated into a common touch screen(s) that is custom programmed to monitor and control onboard systems as described throughout the specifications. The automation system software must allow simultaneous distribution of information to multiple onboard control/monitoring stations and the software must be updateable and configurable as required. This system is mandatory as it simplifies s tart up procedures, contains fewer operating components, reduces operational start -up time, reduces the total amount of wiring in the vehicle and includes error detection protocols and troubleshooting features.
Features include:
• One (1) 10” LCD touch screen with custom graphics for control and monitoring systems • AC power distribution control and monitoring for the generator with power management • DC power distribution control and monitoring
• Manual or automatic generator control
• HVAC and temperature control.
• Interior and exterior lighting control
• Automatic power transfer switches
• Automated startup and shutdown procedures
• Seamless control of generators, lighting, awnings and additional devices • Mast control
• Safety interlocks
• Battery saver feature
• Generator Service Alerts
The system must be completely upgradeable with power modules located throughout vehicle.
Additional components may be added to system with a simple software modification System capability is not to be achieved with use of multiple monitoring systems design ed for specific use i.e. water monitors, battery monitors etc.
NOTE:
Touch screen located above windshield
12.04 1 Additional 10” LCD touch screen with custom graphics for control and monitoring systems. All touch screens provide complete control and monitoring of vehicle systems.
NOTE:
Locate: Middle room, above entry door
12.05 1 3” Touch panel for dedicated local control and monitoring of specific vehicle automation system features. Includes control layout and indicators where applicable.
NOTE:
Location: Exterior TV compartment
LDV@
CUSTOM SPECIALTY VEHICLES
180 Industrial Drive
Burlington, WI 53105 USA
Phone: 800-558-5986
Fax: (262) 763-0156
Direct: +1 (262) 763-0147
www.ldvusa.com
Item Qty
Garden Grove PD (CA) S36MCC-35686-23 CC REV 1
12.06 1 3” Touch panel with numeric display for dedicated local control and monitoring of specific vehicle automation system features including room HVAC. Display shows current room temperature and HVAC setpoint when adjusted. Includes control layout and indicators where applicable.
NOTE:
Location: Rear room.
12.07 Storage Mode maintains the vehicle in a ready-to-deploy condition. Battery chargers, specified outlets, and other pre-determined equipment is powered. HVAC is maintained at a storage mode setting to prevent freezing in the winter or overheating in the summer. The generator can be set to automatically start in the event of a loss of shore power. Other items as necessary can be made available in Storage Mode.
12.08 Travel Mode places the vehicle in a ready-to-travel condition based on vehicle application and equipment. In most cases this includes: starting the generator and transferring off of shore power, turning on HVAC and adjusting temperature to normal operating setpoints, stowing all equipment for travel, powering up communication gear. Travel Mode is a custom programmed, automated process similar to the Auto Startup and Auto Shutdown.
12.09 Reduced Lighting Mode is white ceiling lighting in each room have the option of All-On or Half-On.
12.10 1 Kussmaul Auto Eject 20, 20A-120Vac shore power inlet with 25-ft. 20A-120Vac shore power cord. #091-20WP-120RD.
NOTE:
Streetside front
12.11 1 Marinco 100A-125/250Vac waterproof shore power inlet, 25-ft. 100A-125/250Vac shore power cord and 6-ft. 100A-125/250Vac pigtail.
NOTE:
Streetside front
12.12 8 20A-125Vac duplex receptacle with dual USB charging ports [one (1) Type A and one (1) Type C]. Receptacle is not dedicated to any installed equipment.
NOTE:
Locate:
(1) at Each workstation [Total 6]
(1) front passenger workstation
(1) at rear street side, lower bench seat base
12.13 3 20A-125Vac GFCI duplex receptacle. These receptacles are not dedicated to any installed equipment.
NOTE:
Locate:
(1) Galley area
(1) in Rear exterior street side pass through box
(1) Exterior TV compartment
12.14 2 30A-120 Vac receptacle in electronics rack for UPS.
NOTE:
(1) Street side rack
(1) Curb side rack
LDV@
CUSTOM SPECIALTY VEHICLES
180 Industrial Drive
Burlington, WI 53105 USA
Phone: 800-558-5986
Fax: (262) 763-0156
Direct: +1 (262) 763-0147
www.ldvusa.com
Item Qty
Garden Grove PD (CA) S36MCC-35686-23 CC REV 1
12.15 2 20A-125Vac exterior GFCI duplex receptacle.
NOTE:
Receptacle will be installed with a weatherproof cover. (1) Rear street side
(1) Rear curb side
12.16 Wire chase wire management raceway system located as shown on drawing. Product features:
• Satin anodized finish. The finish resists rust, corrosion and fading. Material extruded from 6063-T5 aluminum alloy.
• Removable dual cover. Makes wiring easy and accessible and provides maximum flexibility for adding or relocating outlets and circuits.
12.17 2 APC Smart-UPS 3,000VA rack mount UPS, SRT3000RMXLA (or current model). Product features:
• 3,000VA/2,700W output capacity
• 120V output voltage
• (8) NEMA 5-20R and (1) NEMA L5-30R output receptacles • Typical Backup Time at Half Load 19.2 minutes (1125 Watts) • Typical Backup Time at Full Load 5.7 minutes (2250 Watts) • Dimensions: 3.35”H x 17”W x 25”D
NOTE:
Locate:
(1) Curb side SRSR Rack
-UPS to power components in Rack
(1) Street side rack
- UPS to power outlets at workstations for PC's and Monitors and rack components
12.18 6 Red specification grade 20A-125Vac duplex receptacle with stainless steel wall plate located as shown on drawing. These receptacles are dedicated to the UPS/Inverter as specified elsewhere in this document.
NOTE:
Locate:
(1) Each at workstations, below counter top [Total 6]
12.19 AC WIRING REQUIREMENTS:
• All AC main wiring shall be stranded THHN wire and run in non-metallic liquid tight conduit. • All AC branch circuit wiring shall be stranded THHN wire (AWG 12 minimum) and run in non - metallic liquid tight and ENT conduit.
• All electrical circuits and appliances shall conform to applicable national electrical codes.
13.00 DC ELECTRICAL SYSTEM:
13.01 1 • Six (6) Lead acid deep-cycle 6Vdc batteries. Batteries shall be installed underbody in slide out weather resistant compartment. Four (4) batteries will be separated for auxiliary equipment and two (2) batteries will be for communications equipment. • Three (3) electronic converter/chargers, 80 amp minimum output each installed underbody in weather resistant climate controlled. Compartment to draw ambient air from interior of truck and will have thermostatically controlled exhaust fan to circulate warm air to ex terior (no exceptions). Converter/charger features:
LDV@
CUSTOM SPECIALTY VEHICLES
180 Industrial Drive
Burlington, WI 53105 USA
Phone: 800-558-5986
Fax: (262) 763-0156
Direct: +1 (262) 763-0147
www.ldvusa.com
Item Qty
Garden Grove PD (CA) S36MCC-35686-23 CC REV 1
• Charges three banks of batteries at the same time.
• UL listed for safety.
• Manual reset circuit breaker.
• Reverse battery protection.
• Electronic current limiting.
• High voltage protection.
• All DC electrical and metering switched and monitored through the multiplex system.
13.02 18 Light, Orion 6" LED, neutral white with polished bezel and voltage regulation.
13.03 8 Light, Orion 6" LED, neutral white / red with polished bezel and voltage regulation.
13.04 8 Whelen M9LZC Gradient LED Scene Light with chrome flange.
NOTE:
Locate:
(3) Street side
(3) Curb side
(2) Rear
13.05 6 Whelen PEL2C LED light with chrome housing.
NOTE:
Three (3) Street side, Three (3) Curb side
13.06 4 12VDC dual USB power port.
NOTE:
Locate:
(2) at Exterior TV compartment
(1) at drivers area
(1) at Rear curb side exterior pass through box
13.07 12VDC WIRING REQUIREMENTS:
• 2-gauge minimum copper stranded battery cable shall be used for 12Vdc main supply lines.
All cable runs shall be full length, no splices. All cable terminals shall be staked and soldered.
All cable shall be enclosed in convoluted polyethylene tubing and the ends of the cable shall be sealed with color-coded shrink-wrap identifying the function of the cable. • All added electrical branch circuits shall be protected from over-current by resettable circuit breakers appropriately rated for the load. Only circuit breakers shall be used in the installation of added electrical branch circuit wiring (plug type fuses are unacceptable). • Circuit breaker functions shall be identified by engraved or printed labels. • All added wiring for load runs of AWG 10, 12, 14, and 18, shall conform to MIL -W-16878/2 and/or UL1007/1569”
• All added wiring for load runs of AWG 8, shall conform to MIL-W-16878/3 and/or UL1028 • Wire terminals for added circuits must conform to MIL-T-7928. Terminals shall be insulated, insulation grip, TYPE II, CLASS 2 and shall be crimped with tooling recommended by the terminal manufacturer.
• All wiring shall be numbered or lettered on 6" centers minimum. • Wiring shall be protected from chafing and abrasion with convoluted polyethylene tubing (wire loom) as required.
• Where wire passes through sheet metal, bulkheads and structural supports, plastic grommets
LDV@
CUSTOM SPECIALTY VEHICLES
180 Industrial Drive
Burlington, WI 53105 USA
Phone: 800-558-5986
Fax: (262) 763-0156
Direct: +1 (262) 763-0147
www.ldvusa.com
Item Qty
Garden Grove PD (CA) S36MCC-35686-23 CC REV 1
shall be used to protect both wiring and wire looms.
• All wire bundles shall be tied with trimmed nylon ties. • Extreme care shall be exercised to provide for easy serviceability of the system in future years.
• Extreme care must be taken in the installation to avoid the engine manifold, engine exhaust, and muffler, which could expose the wiring to severe overheating during long periods of operation. Proper insulation and heat deflection panels must be installed in such areas. • A high-current 12Vdc system wiring schematic shall be provided. • These are the minimum acceptable 12Vdc wiring requirements.
14.00 EMERGENCY LIGHTING / SIRENS:
14.01 1 Whelen 295SLSA6 siren with 9 low current lighting control switches. California Title 13 compliant.
NOTE:
Slide Bar Positions Control:
1. Rear (Upper and Lower)
2. Rear (Upper and Lower), All Upper, Front Wall or "Light bar"
3. All
14.02 1 Whelen SA315P high performance speaker.
14.03 1 Whelen TLIR ION-T- Series™ Linear Super-LED® Red with clear outer lens & TIONFC chrome flange.
NOTE:
Street side Grille
-Red light to be set to steady burn
14.04 1 Whelen TLIB ION-T- Series™ Linear Super-LED® Blue with clear outer lens & TIONFC chrome flange.
NOTE:
Curb side Grille
14.05 9 Whelen M6 series, M6RC (or current model), Linear Super-LED lighthead with internal flasher, RED LED's with CLEAR outer lens. Includes M6FC chrome flange.
NOTE:
Locate:
(2) Above windshield
(2) Street side
(2) Rear
(1) Tail light housing
(2) Curb
14.06 9 Whelen M6 series, M6BC (or current model), Linear Super-LED lighthead with internal flasher, BLUE LED's with CLEAR outer lens. Includes M6FC chrome flange.
NOTE:
Locate:
(2) Above windshield
(2) Street side
(2) Rear
(1) Tail light housing
LDV@
CUSTOM SPECIALTY VEHICLES
180 Industrial Drive
Burlington, WI 53105 USA
Phone: 800-558-5986
Fax: (262) 763-0156
Direct: +1 (262) 763-0147
www.ldvusa.com
Item Qty
Garden Grove PD (CA) S36MCC-35686-23 CC REV 1
(2) Curb
14.07 1 Custom fabricated bracket to mount M6 series light above windshield, painted to match body.
15.00 AUDIO / VIDEO:
15.01 6 LG 24" Black 720P LED HDTV - 24LM530S-PU Features:
• 720P resolution
• (2) HDMI inputs
• (2) Speakers
NOTE:
Locate:
(1) at each workstation [Total 6]
15.02 6 ASUS ProArt Display PA329CV 32" 16:9 Adaptive-Sync UHD HDR IPS Monitor • 3840 x 2160 UHD Resolution @ 60 Hz
• (2) HDMI, (1) Display port
• Vesa Mount 100 x 100mm
• Dimensions: 16.86" x 28.63" x 2.67"
NOTE:
Locate:
(1) at each workstation [Total 6]
Monitor to be centered in between Tv's located at workstations
15.03 1 Samsung 55" QLED TV (QN60Q60BAF) with wall mount bracket. Product features:
• Resolution 4K
• (3) HDMI, (2) USB
• (2) Speakers
• DTV Tuner/ATSC / Clear QAM
• Dimensions: 53.1"(W) x 30.6"(H) x 1"(D) Weight 41.01lbs NOTE:
Locate:
Exterior curb side TV compartment
15.04 1 Weatherproof single door exterior work station and TV/monitor compartment. Constructed from
0.125" aluminum with all welded seams and hinged at the top.
Includes:
• Internal flip down work surface
• LED strip light (illuminates when door is opened)
• Gas charged lift support and locking latch
NOTE:
• 55” Samsung TV
• 2 HDMI, one input, one output
• 3” intel-I touch pad
• Extron control pad
• (2) Cat6 network ports
• Duplex receptacle
• Dual 12V, with USB charger
• (1) APX8500 radio
LDV@
CUSTOM SPECIALTY VEHICLES
180 Industrial Drive
Burlington, WI 53105 USA
Phone: 800-558-5986
Fax: (262) 763-0156
Direct: +1 (262) 763-0147
www.ldvusa.com
Item Qty
Garden Grove PD (CA) S36MCC-35686-23 CC REV 1
15.05 1 Axis camera station S2208 standalone NVR. All-in-one 8-channel, 4TB, high definition recorder with integrated switch.
15.06 1 Wireless keyboard and mouse combo with USB dongle.
15.07 1 Prewire and make installation provisions for customer owned DSS receiver, does not include rack mount kit.
15.08 1 Axis Communications four camera perimeter surveillance system with T8705 video decoder One (1) F9114 Box connect up to 4 camera sensors:
• Full HD 1080p Video
• Up to 4 Axis Sensor Units Supported
• H.264 Compression
Four (4) F2105-RE camera sensor lens:
• 1080p resolution 1920 x 1080
• Lens F2.0, 3.1mm with 108° horizontal field of view and 58° vertical field of view • Low light performance
• Color
• Fixed iris
• Fixed focal
Mounted on exterior wall.
15.09 1 SD Memory Card for IP camera. The SD card shall record IP camera allowing it to be downloaded and viewable via an IP address.
NOTE:
256 GB SD Card
15.10 1 JACK® model OA8500 Digital HDTV Antenna + Mount with SureLock™ DTV Signal Meter. No crank up, built in Amplifier and 360° rotation for improved reception.
15.11 1 Extron DXP 1616HD 4K PLUS 16X16 HDMI Matrix Switcher. 60-1497-01 NOTE:
INPUTS: (13)
(2) Mast cameras
(1) Perimeter Camera
(1) Future DSS receiver
(1) Extron Sharelink
(6) HDMI Inputs at workstations #1-6
(1) HDMI Input in Exterior workstation
(1) HDMI Input at Exterior input box
OUTPUTS:
(6) 24" TV
(4) 32" Monitor's
(1) 55" Exterior TV
(1) HDMI output at Exterior workstation
(1) HDMI output at Exterior input box
15.12 3 Extron MKP 2000 X-Y Remote Control Panel for Extron Matrix Switchers.
NOTE:
Locate:
(1) Front room
LDV@
CUSTOM SPECIALTY VEHICLES
180 Industrial Drive
Burlington, WI 53105 USA
Phone: 800-558-5986
Fax: (262) 763-0156
Direct: +1 (262) 763-0147
www.ldvusa.com
Item Qty
Garden Grove PD (CA) S36MCC-35686-23 CC REV 1
(1) Rear room
(1) Exterior TV compartment
15.13 1 Extron ShareLink Pro 500 Series Wireless Collaboration Gateway Key Features
• Wirelessly share content from personal mobile devices • Supports Microsoft Windows® and OS X® computers as well as Apple® and Android ™ smartphones and tablets
• Integrated dual band wireless access point at 2.4 GHz or 5 GHz • Provides full screen mirroring for Apple iOS devices1 • Dedicated mobile app, MirrorOp® for Extron ShareLink™, for reliable iOS and Android content sharing
16.00 MAST AND MAST MOUNTED EQUIPMENT:
16.01 1 Fireco 2200 series heavy-duty non-locking telescoping pneumatic mast.
Mast features:
• 265 lb. max top load capacity
• 26' 2" extended height
• 6' 1" nested height
Includes:
• KEY-WAY breakaway nylon key prevents tower rotation. Easily replaceable. • Air safety valve for over pressure release and condensation drainage. • Water drainage holes to avoid freezing at low temperatures. • Interlock to prevent vehicle from being driven with mast raised. • Fireco tower does not require routine lubrication.
• Mast cap covers the top of all tower sections when the tower is in the retracted position keeping dirt and moisture out of the tower when stowed.
16.02 1 Thomas Ultra Air-Pac 1/2-hp compressor with 2 gallon air tank.
16.03 1 Custom fabricated 0.125" aluminum Nycoil cylinder painted to match body color.
16.04 1 Custom fabricated bracket on mast to mount two individual camera systems.
NOTE:
Mast mount
(2) CAT6 for mast cameras
(2) CAT6 Spares
(1) Power for look up light
16.05 1 Mast lookup light mounted on mast.
16.06 1 Weatherproof mast up/down control switch on exterior of vehicle.
16.07 2 AXIS Q6318-LE PTZ Dome Network Camera
• 4K UHD and 31x optical zoom
• Axis Sharpdome technology with Speed Dry
• Optimized IR with power-efficient, long-life 850 nm IR LEDs, range of reach 300 m (984 ft) or more depending on the scene
• Built-in laser that provides laser focus for precise focus and quick-zoom functionality, it allows you to easily follow fast-moving objects
LDV@
CUSTOM SPECIALTY VEHICLES
180 Industrial Drive
Burlington, WI 53105 USA
Phone: 800-558-5986
Fax: (262) 763-0156
Direct: +1 (262) 763-0147
www.ldvusa.com
Item Qty
Garden Grove PD (CA) S36MCC-35686-23 CC REV 1
16.08 2 Axis T8705 Video Decoder
• Enables digital monitors to connect to and display live video from Axis network cameras • HDTV 1080p HDMI video decoder
• Sequence and Multiview (up to 16 cameras)
16.09 2 SD Memory Card for IP camera. The SD card shall record mast camera allowing it to be downloaded and viewable via an IP address.
NOTE:
256GB
17.00 RADIOS:
17.01 Primary 12Vdc power leads for communications radios shall be minimum 2-gauge copper stranded wire with soldered crimp-on end connectors (gauge based on radio requirements).
Cables shall be enclosed in convoluted tubing and function identified with colored shrink-wrap.
Power to radios shall be controlled by a continuous-duty switch actuated by the auxiliary battery disconnect switch.
17.02 8 Prewire and make installation provisions for communications radio. Installation includes:
• NMO-style base on the roof or antenna raceway, as applicable. • LMR195 antenna cable routed to radio transceiver location in Carlon Carflex ENT conduit. • 12Vdc power routed to radio transceiver location.
NOTE:
Customer supplied radios and locations:
Motorola APX-8500 all band single antenna radios
(1) Cab area
(2) at street side workstations
(2) at curb side workstations
(2) at rear curb side workstations
(1) Exterior TV compartment
17.03 Install hinged panels under countertops to conceal radio transceivers where applicable.
17.04 1 Fabricate and install 3" x 3" square aluminum tubing antenna raceway on the roof of the vehicle. Antenna raceway will penetrate the roof on each side of the truck at radio box locations and in the overhead console location. Includes:
• 3" high x 3" long aluminum access cover at each antenna base location on the side of the tubing for access to antenna base and coax cable.
• Access covers with watertight gasket and attached with four (4) stainless steel machine screws. Raceway tube to have nut-serts installed for access cover attachment. • Carlon Carflex ENT conduit routed from antenna raceway penetration location to radio transceiver locations.
17.05 9 Magnetic microphone holder. Magnetic Mic MMSU-1.
LDV@
CUSTOM SPECIALTY VEHICLES
180 Industrial Drive
Burlington, WI 53105 USA
Phone: 800-558-5986
Fax: (262) 763-0156
Direct: +1 (262) 763-0147
www.ldvusa.com
Item Qty
Garden Grove PD (CA) S36MCC-35686-23 CC REV 1
18.00 COMPUTER NETWORK AND EQUIPMENT:
18.01 19 RJ-45 Cat6 computer network jack with Cat6 cable routed through Carlon Flex-Plus ENT conduit or raceway (as applicable).
NOTE:
Network runs will be tagged at each end to facilitate future trouble shooting, expansion, or modification.
Locations:
• Two (2) @ workstations #1-6 (Qty. 12)
• One (1) @ printer
• Two (2) @ the passenger seat area
• Two (2) in exterior TV compartment
• Two (2) in the exterior input box
18.02 1 Leviton 69270-U48 (or current model) 48-port Cat6 rack mount patch panel.
18.03 Certified 18" Cat6 patch cord. As Required.
18.04 Certified 36" Cat6 patch cord. As Required.
18.05 1 Cable Certification Report confirming that network wiring complies with Cat6 specifications.
18.06 1 HP Color LaserJet Pro Multi-Function Printer (MFP) M479FDW Product features:
• Black/white or color print, copy, scan, and fax capable • 1 Hi-Speed USB 2.0; 1 host USB at rear side;Gigabit Ethernet 10/100/1000BASE-T network; 802.3az(EEE) 802.11b/g/n / 2.4 / 5 GHZ Wi-Fi radio
• Dimensions (W X D X H) 16.8 x 25.7 x 16.3 in; 51.6 Lbs.
NOTE:
Located: Curb side
18.07 6 Install customer supplied computers. Install includes mount and Dual USB cables run from computer to wall plate.
NOTE:
Locate: (1) each at Workstations #1-6
18.08 1 Cradlepoint E3000 cellular router with WiFi (5G Modem) and 1-year NetCloud Enterprise Branch Essentials Plus Advanced Plan.
NOTE:
If Cradlepoint brand, info requirement to transfer device support:
• Name of Company/Agency -
• Physical address -
• Persons Name -
• E-mail address
18.09 1 Cradlepoint MC400 5GV Wireless Cellular Modem (BF-MC400-5GB) for E300/E3000 Enterprise Branch Routers.
18.10 1 Cellular modem antenna with GNSS. Airgain CENTURION Next 9 IN 1 High Performance External IP67 Antenna for LTE and 5G. 4x Cellular (600 MHz-6 GHz), 4x WIFI and GNSS, Threaded-Bolt Mount, 15 FT Cabling With SMA Connectors for Cell/GNSS, and RP-SMA for WIFI, Black.
LDV@
CUSTOM SPECIALTY VEHICLES
180 Industrial Drive
Burlington, WI 53105 USA
Phone: 800-558-5986
Fax: (262) 763-0156
Direct: +1 (262) 763-0147
www.ldvusa.com
Item Qty
Garden Grove PD (CA) S36MCC-35686-23 CC REV 1
18.11 1 Cellular modem antenna with GNSS. Airgain CENTURION Next High Performance External IP67 Antenna for LTE and 5G. 4x Cellular (600 MHz-6 GHz), Threaded-Bolt Mount, 15 FT Cabling With SMA Connectors for Cell, Black.
19.00 MISCELLANEOUS ELECTRONICS:
19.01 1 Middle Atlantic Products, Inc. MRK-4026 forty-space 19" wide x 26.5” depth (24” useable depth) open framed electronics equipment rack with caster base. Rack can easily slide out from its fixed position to allow side access to rack equipment.
NOTE:
Rack located street side
19.02 1 Middle Atlantic VFD-40 Vented front door with Thumb Latch (No Key Lock).
19.03 1 Middle Atlantic MW-4FT top fan panel, with two (2) 50 cfm ventilation fans, QFAN.
19.04 3 Middle Atlantic PD-815SC-NS 15 amp power strip with eight (8) outlets. Includes PB-XS rack mounting bracket.
19.05 1 2" box pan door and door frame fabricated from 0.125" aluminum installed in body to allow exterior access to Middle Atlantic equipment rack. Includes key lock and gas spring.
NOTE:
Street side rack
19.06 1 Custom fabricated mounting system to secure Middle Atlantic SRSR-4-18 (or current model) eighteen (18) space 19" wide x 26.5” depth (24” useable depth) open framed EIA electronics equipment rack with sliding rail system and swivel base. Rack to easily slide out and swivel from its fixed position allowing full access to rack mounted equipment. 250lb weight limit.
NOTE:
Rack located curb side.
19.07 1 Middle Atlantic FTA-3 1 space fan tray, with three (3) 69 cfm ventilation fans.
19.08 3 Cast Products EB00013-1 (or current model) cast aluminum box with key lock. The rear of the box will be removed to allow cables to be passed into the vehicle.
NOTE:
Locate:
(1) Street side, workstation #2
(1) Curb side, workstation #4
(1) Curb side, rear workstation #5
19.09 3 Shroud with weatherproof pass-through hatch installed in the door of the input box.
20.00 EXTERIOR STORAGE COMPARTMENTS:
20.01 1 Double door underbody storage compartment with approximate interior dimensions up to 15" high x up to 72" wide x 25" deep constructed from 0.125" aluminum with all welded seams.
NOTE:
Locate: Street side
LDV@
CUSTOM SPECIALTY VEHICLES
180 Industrial Drive
Burlington, WI 53105 USA
Phone: 800-558-5986
Fax: (262) 763-0156
Direct: +1 (262) 763-0147
www.ldvusa.com
Item Qty
Garden Grove PD (CA) S36MCC-35686-23 CC REV 1
20.02 Compartments listed above will be constructed to the following specifications:
• Sweep out type bottoms with 1/2” drain holes.
• 2" box pan doors and door frames fabricated from 0.125" aluminum. • Door frames shall be riveted to the body and welded to the compartments. • Compartments shall have an LED light that illuminates when the door is opened.
Compartment doors will be constructed to the following specifications:
• Stainless steel hinges attached with stainless machine screws. • Slam latches and flush mounted handles.
• 0.100" bright polished aluminum diamond plate on interior surfaces fastened with stainless hardware.
• All doors shall be sealed with industrial grade neoprene gasket.
21.00 MISCELLANEOUS OTHER:
21.01 1 Girard Nova motorized retractable lateral arm awning. Features:
• Dual-pitch awning with up to three lateral arms for superior strength, • AC electric powered motor with crank handle/manual override • Sensor that will retract the awning to prevent damage from the wind
21.02 1 Rooftop lateral arm awning mounting bracket.
21.03 1 15" wide roof access ladder mounted on rear. Ladder features:
• All welded construction for maximum strength
• 1" diameter X 0.083" brush finished tubular aluminum rails • Aluminum grip-strut rungs
21.04 1 Heavy-duty Quadra Mfg. Bigfoot© four point fully automatic one-touch leveling system.
Includes:
• Four (4) QEII-24 jacks with 17,000-lb. capacity each, 24" long with 18" stroke • Air ride dump valve
• Fully automatic control panel with manual feature
• Safety interlock when jacks are deployed
21.05 1 Set of four (4) Super Dolly Pads high density polypropylene, injection molded yellow colored for use with leveling system jacks. Pads measure 15” x 17” x 1” thick with a grab strap on one side.
21.06 1 5 pound dry chemical fire extinguisher.
21.07 3 Battery powered combination Carbon Monoxide and Smoke alarm.
21.08 1 Complete manual set, including the following (as applicable):
• As-built specifications with interior and exterior drawings as used for production of the vehicle. • Chassis and body owner's manuals.
• 12Vdc and 120Vac legends showing wire gauge, color, number and function. • 12Vdc high current wiring diagram illustrating the battery system, isolators, power converters, alternator, disconnect switches and control panels.
• Roof top antenna placement drawing and legend identifying antenna placements and termination points.
• Audio/Video cabling diagram.
• Chassis and generator maintenance and service logs.
• Battery maintenance information.
LDV@
CUSTOM SPECIALTY VEHICLES
180 Industrial Drive
Burlington, WI 53105 USA
Phone: 800-558-5986
Fax: (262) 763-0156
Direct: +1 (262) 763-0147
www.ldvusa.com
Item Qty
Garden Grove PD (CA) S36MCC-35686-23 CC REV 1
• All individual component manuals and warranty registration cards as provided by component manufacturers. Customer is responsible for completing warranty cards and mailing them to manufacturers.
21.09 1 TRAINING. An LDV representative will provide up to eight (8) hours of orientation on LDV provided systems, as applicable:
• Generator start up and shut down procedure
• Leveling system operation
• AC and DC electrical systems operation
• HVAC systems operation
• Mast operation
• Audio/Video system operation, does not include programming DVR's, TV's, etc. • Awning operation
21.10 LDV warranty of one (1) year/12,000 miles, whichever comes first, for manufacturer’s defects in materials and workmanship. Refer to LDV warranty statement for details of warranty coverage.
21.11 Note: Project scope does not include certain tasks or costs that are the responsibility of the customer unless clearly specified as LDV supplied. These items include, but are not limited to:
• Radio and telephone system programming.
• Activation and service fees for cellular telephones, satellite telephones, satellite TV, satellite internet access.
• Loading and configuring computer software.
In the event of a discrepancy between the drawing and specification, the specification will supersede. LDV reserves the right to make substitutions of equal quality and specifications of those listed in this document.
Some component models change frequently. In the event that a specified component model becomes unavailable at the time LDV attempts to source it, LDV will provide a replacement model with equivalent or better features, as agreed upon with the customer.
LDV@
CUSTOM SPECIALTY VEHICLES
Agenda Item - 5.a.
City of Garden Grove
INTER-DEPARTMENT MEMORANDUM
To: Lisa L. Kim From: Niki Wetzel
Dept.: City Manager Dept.: Community Development
Subject: Second reading and adoption
of Ordinance No. 2943
Date: 10/24/2023
Attached for second reading and adoption is Ordinance No. 2943.
ATTACHMENTS:
Description Upload Date Type File Name
Ordinance No. 2943 10/16/2023 Ordinance 2943_City_Council_Ordinance_(A- 037-2023)_(1).pdf
ORDINANCE NO. 2943
AN ORDINANCE OF THE CITY COUNCIL OF THE CITY OF GARDEN GROVE APPROVING ZONING MAP AMENDMENT NO. A-037-2023 TO REVISE THE CITY’S OFFICIAL ZONING MAP TO IMPLEMENT THE UPDATES TO THE ADOPTED 2021-2029 HOUSING ELEMENT AND TO CLARIFY THE SITES
INTENDED TO BE INCLUDED IN THE INTERNATIONAL WEST MIXED USE OVERLAY AND THE INDUSTRIAL/RESIDENTIAL MIXED USE 1 OVERLAY PURSUANT TO ORDINANCE NO. 2925
CITY ATTORNEY SUMMARY
This Ordinance amends the City’s Of ficial Zoning Map (i) to apply the International West Mixed Use Overlay to one (1) additional parcel and the Industrial/Residential Mixed Use 1 Over lay to ten (10) additional parcels identified in the Sites Inventory of the amended 2021-2029 Housing Element of the General Plan adopted by the Garden Grove City Council on October 10, 2023, and (ii) to clarify the Official Zoning Map to specify fifteen (15) parcels to which the International West Mixed Use Overlay and the Industrial/Residential Mixed Use 1 Overlay are intended to apply, but which, due to a clerical error, were inadvertently not listed on Exhibit E to Ordinance No. 2925, adopted by the Garden Grove City Council on December 14, 2021.
THE CITY COUNCIL OF THE CITY OF GARDEN GROVE FINDS AND DETERMINES AS FOLLOWS:
WHEREAS, Government Code 65584 requires local jurisdictions to encourage, promote, and facilitate the development of housing to accommodate its regional housing need; and
WHEREAS, the State-mandated 6
th Cycle of the Regional Housing Needs
Assessment (RHNA) requires the City of Garden Grove to plan for 19,168 dwelling units for all income level during the 2021-2029 planning period; and
WHEREAS, on November 9, 2021, the Garden Grove City Council adopted Resolution No. 9714-21 (i) adopting a Mitigation Monitoring and Reporting Program, (ii) adopting a Statement of Overriding Consideratio ns, and (iii) certifying the Program EIR for the Focused General Plan Update and Zoning Amendments (“FGPUZA”) project, State Clearinghouse No. 2021060714. The FGPUZA project consisted of (i) General Plan Amendment No. GPA-003-2021, consisting of updates to the General Plan Housing Element, Land Use Element, and the Safety Element, and adoption of a new General Plan Environmental Justice Element to comply with State law provisions, including complying with the 6
th Cycle (2021-2029) of the Regional
Housing Needs Assessment (R HNA) that requires the City to plan for 19,168 residential dwelling units for all income levels during the 2021-2029 planning period; and (ii) Zoning Amendment No. A-031-2021, consisting of text/map amendments to Title 9 of the Municipal Code and to the Zoning Map to implement the Housing Element and Land Use Element Updates; and
Garden Grove City Council
Ordinance No. 2943
WHEREAS, on November 9, 2021, the Garden Grove City Council adopted Resolution No. 9713-21 approving Gene ral Plan Amendmen t No. GPA-003-2021, including adoption of the 2021-2029 Housing Element; and
WHEREAS, on December 14, 2021, the Garden Grove City Council adopted Ordinance No. 2925 approving Zoning Am endment No. A-031-2021 to implement the General Plan Housing Element and Land Use Element updates adopted by the City Council on November 9, 2021. Pursua nt Ordinance No. 2925, the City Council added Section 9.18.190 to the Garden Grove Municipal Code creating the Mixed Use Overlay (MU) Zone, which includes the International West Mixed Use Overlay, the Industrial/Residential Mixed Use 1 Overlay, and the Re sidential/Commercial Mixed Use 2 Residential Overlay; and
WHEREAS, following a public hearing, on October 10, 2023, the City Council of the City of Garden Grove ad opted Resolution No. 9825-23 approving General Plan Amendment No. GPA-002-2023, which incl udes updates to the adopted 2021-2029 Housing Element and an amendment to the Land Use Element to change the Land Use Designation of a property located at 13621 Harbor Boulevard (Assessor’s Parcel No. 100-123-01) from Industrial (I) to International West Mixed Use (IW), in order to comply with State law provisions and resolve comments received from the California Department of Housing and Community Development (“HCD”) on the adopted 2021- 2029 Housing Element, in order to obtain HCD certification of the City’s Housing Element; and
WHEREAS, in conjunction with Gene ral Plan Amendment No. GPA-002-2023, the City of Garden Grove is also proposing to adopt a Zoning Map Amendment (A-037-2023) to revise the Zoning Map to implement the updates to the Housing Element and to clarify the sites intended to be included in the International West Mixed-Use Overlay and the Industrial/Resi dential Mixed Use 1 Ov erlay pursuant to Ordinance No. 2925. Specifically, the proposed Zoning Map Amendment will (i) apply the International West Mixed Use Overlay to one (1) additional parcel and the Industrial/Residential Mixed Use 1 Overlay to ten (10) additional parcels identified in the Sites Inventory of the amended 2021-2029 Housing Element of the General Plan adopted by the Garden Grove City Council on October 10, 2023, and (ii) clarify the Official Zoning Map to specify fifteen (15) parcels to which the International West Mixed Use Overlay and the Industrial/Resi dential Mixed Use 1 Overlay are intended to apply, but which, due to a clerical error, were inadvertently not listed on Exhibit E to Ordinance No. 2925; and
WHEREAS, pursuant to Resolution No . 9825-23, the City Council found that, based on substantial evidence in the record, no further review under the California Environmental Quality Act (“CEQA”) is required for General Plan Amendment No. GPA-002-2023 and Zoning Map Amendmen t No. A-037-2023 pursuant to Public Resources Code Section 21166 and CEQA Guidelines Sections 15168 and 15162 because the proposed General Plan and zoning amendments associated with the revisions to the Housing Element fall within the scope of impacts analyzed in the City of Garden Grove Focused General Pl an Update and Zoning Amendments
Garden Grove City Council
Ordinance No. 2943
Environmental Impact Report, State Clearinghouse No. 2021060714 (“Garden Grove General Plan Update and Focused Zoning Amendments”), and the General Plan and zoning amendments will not result in any new significan t impacts or a substantial increase in the severity of previously identified significant impacts; and
WHEREAS, the Planning Commission of the City of Garden Grove held a duly noticed public hearing on September 21, 2 023 and considered all oral and written testimony presented regarding the proposed General Plan and Zoning Map amendments; and
WHEREAS, on September 21 , 2023, following the public hearing, the Planning Commission adopted (i) Resolution No. 6069-23 recommending that the City Council:
Adopt a General Plan Amendment (GPA-002-2023), and (ii) Resolution No. 6070-23 recommending that the City Council approve Zoning Map Amendment No.
A-037-2023; and
WHEREAS, a duly noticed public hearing regarding General Plan Amendment No. GPA-002-2023 and Zoning Map Amendment No. A-037-2023 was held by the City Council on October 10, 2023, and a ll interested persons were given an opportunity to be heard; and
WHEREAS, the City Council of the City of Garden Grove gave due and careful consideration to the matter during its me eting of October 10, 2023, and considered all oral and written testimony presented.
WHEREAS, the City Council hereby makes the following findings regarding Zoning Map Amendment No. A-037-2023:
A. The proposed zoning map amendments are internally consistent with the goals, policies, and elements of the General Plan. Pursuant to General Plan Amendment No. GPA-002-2023, the City Council has adopted updates to the Housing Element and Land Use Elemen t to comply with the State’s 6 th Cycle (2021-
2029) of the Regional Housing Needs Assess ment (RHNA) that requires the City to plan for 19,168 additional re sidential dwelling units for all income levels during the planning period. The proposed Zoning Map Amendment will revise the City’s Zoning Map to apply the International West Mixed Use Overlay to one (1) additional property and the Industrial/R esidential Mixed Use 1 Overla y to ten (10) additional properties that were added to the Housing Element Sites Inventory through General Plan Amendment No. GPA-002-2023. In a ddition to being listed in the Housing Element Sites Inventory, these eleven (1 1) properties all have an underlying General Plan Land Use Designation that allows residential development at the densities permitted by the Overlay zoni ng. The proposed Zoning Map Amendment will also specify fifteen (15) parcels to which the International West Mixed Use Overlay and the Industrial/Residential Mixed Use 1 Overlay apply, but which, due to a clerical error, were inadvertently not listed on Exhibit E to Ordinance No. 2925.
These fifteen (15) parcels ar e also listed in the Housing Elements Sites Inventory and have an underlying General Plan Land Use Designation that allows residential development at the densities permitted by the Overlay zoning. The focus of the
Garden Grove City Council
Ordinance No. 2943
General Plan and Zoning Map Amendments is to comply with St ate law provisions and resolve comments received from the California Department of Housing and Community Development (“HCD”) on the adopted 2021-2029 Housing Element, in order to obtain HCD certification of the City’s Housing Element.
B. The proposed zoning map amendmen ts will promote the public interest, health, safety, and welfare of the surrounding community. Zoning Map Amendment No. A-037-2023 will implement the goals, policies and programs of the updated Housing Element and facilitate certification of the Housing Element by HCD.
C. The parcels subject to the proposed Zoning Map amendments are physically suitable for the requested land use designation(s), compatible with surrounding land uses, and consistent with the General Plan. The proposed Zoning Map Amendment will revise the City’s Zoning Map to apply the International West Mixed Use Overlay to one (1) additional property and the Indu strial/Residential Mixed Use 1 Overlay to ten (10) addition al properties that were added to the Housing Element Sites Inventory through General Plan Amendment No. GPA-002-2023. These eleven (11) pro perties were evaluated in conjunction with General Plan Amendment No. GPA-002-2023 and determined to be suitable for the development of housing, and they each have an underlying General Plan Land Use Designation that allows residential dev elopment at the densities permitted by the Overlay zoning. The proposed Zoning Map Amendment will al so specify fifteen (15) parcels to which the International West Mixed Use Overlay and the Industrial/Residential Mixed Use 1 Overlay apply, but which, due to a clerical error, were inadvertently not listed on Exhibit E to Ordinance No. 2925. These fifteen (15) parcels were evaluated in conjuncti on with the 2021 FGPUZA project and determined to be suitable for the developme nt of housing, are identified in the Housing Elements Sites Inventory, and ha ve an underlying General Plan Land Use Designation that allows residential devel opment at the densities permitted by the Overlay zoning. All 26 parcels subject to the proposed Zoning Map Amendments are physically suitable for the mixed use ov erlay, given the compatibility with the underlying General Plan Land Use Designations which allows residential development, and permitting the development of residential uses on these parcels will be compatible with the surrounding land uses in their respec tive vicinity, given that adjacent properties also have simila r General Plan Land Use Designations and mixed use overlay zoning.
NOW, THEREFORE, THE CITY COUNCIL OF THE CITY OF GARDEN GROVE DOES ORDAIN AS FOLLOWS:
SECTION 1. The City Council finds that the above recitals are true and correct.
SECTION 2. Zoning Map Amendment No. A-037-2023 is hereby approved pursuant to the findings set forth herein and the facts and reasons stated in Planning Commission Resolution No. 6070-23, a copy of which is on file in the Office of the City Clerk, and which is in corporated herein by refere nce with the same force and effect as if set forth in full.
Garden Grove City Council
Ordinance No. 2943
SECTION 3. The properties shown on the maps and accompanying list of properties with corresponding property Assessor’s Parcel Numbers attached hereto as Exhibit "A” shall be included in the International West Mixed Use Overlay and the Industrial/Residential Mixed Use 1 Overlay, as specified in Exhibit “A.” Exhibit “E” to Ordinance No. 2925 shall be superseded to the extent it is inconsistent with Exhibit “A” attached hereto. The Zoning Map shall be amended accordingly.
SECTION 4. If any section, subsection, subdivision, sentence, clause, phrase, word, or portion of this Ordinance is, for any reason, held to be invalid or unconstitutional by the decision of any court of competent jurisdiction, such decision shall not affect the validity of the remaining portions of this Ordinance. The City Council hereby declares that it would have adopted this Ordinance and each section, subsection, subdivision, sentence, clause, phrase, word, or portion thereof, irrespective of the fact that any one or more sections, subsec tions, subdivisions, sentences, clauses, phrases, words or portions thereof be declared invalid or unconstitutional.
SECTION 5: The Mayor shall sign and the City Clerk shall certify to the passage and adoption of this Ordinance and shall cause the same, or the summary thereof, to be published and posted pursuant to the provisions of law and this Ordinance shall take effect thirty (30) days after adoption.
The foregoing Ordinance was passed by the City Council of the City of Garden Grove on the ___ day of ____________.
ATTEST:
MAYOR
_______________________________
DEPUTY CITY CLERK
STATE OF CALIFORNIA )
COUNTY OF ORANGE ) SS:
CITY OF GARDEN GROVE)
I, LIZABETH VASQUEZ, Deputy City Cler k of the City of Garden Grove, do hereby certify that the foregoing Ordinance was introduced for first reading and passed to second reading on October 10, 2023, with a vote as follows:
AYES: COUNCIL MEMBERS: (6) O’NEILL, TRAN, DOVINH, KLOPFENSTEIN,
NGUYEN-PENALOZA, JONES
NOES: COUNCIL MEMBERS: (1) BRIETIGAM
ABSENT: COUNCIL MEMBERS: (0) NONE
WEST
HARBOR
WESTMINSTER
TRASK
GARDEN GROVE
CITY OF GARDEN GROVE
COMMUNITY DEVELOPMENT DEPARTMENT
PLANNING SERVICES DIVISION
±
EXHIBIT A
MIXED USE OVERLAY ZONE
INTERNATIONAL WEST MIXED USE OVERLAY
SITE AREA MAP 1
LEGENDS
NOTES
1. LAND USE DESIGNATION – INTERNATIONAL WEST MIXED USE
2. ZONING: C-1, C-2, C-3, M-1, HCSP-TS, HCSP-SDS, HCSP-OP Existing parcels
New parcels
EXHIBIT "A"
GARDE IN G R.OVE
. ■ ' '' J
[gJ 1111 jg::JCJ
>-----
-
- I ~
1 1 · ' 1 1· . 1 I -•- ■- - ■- - ■ ------ ■- - ■- -■- ■- ■- - ■- -■- ■-■-■- ■- -■-
CHAPMAN
GARDEN GROVE
HOOVER
LAMPSON
WESTERN
KNOTT
BEACH
CITY OF GARDEN GROVE
COMMUNITY DEVELOPMENT DEPARTMENT
PLANNING SERVICES DIVISION
±
EXHIBIT C
MIXED USE OVERLAY ZONE
INDUSTRIAL/RESIDENTIAL MIXED USE 1 OVERLAY
LEGENDS
NOTES
1. LAND USE DESIGNATION – INDUSTRIAL/RESIDENTIAL MIXED USE 1
2. ZONING: M-P (INDUSTRIAL PARK)
Existing parcels
New parcels
City boundaries
EXHIBIT "A"
GARDE IN G R.OVE
·-·-·-·-·-·-
....... • I 1. ••• .r
..-- , T
'Ii J
I
··-·-·-·-·-·-·-·-· I
I
I
-I
J
!. .•.•.•. !,
I
i. .
w -
,--·-·-·-·-·-·-·-·-~
I
■-■-■-■-■-■-■-■-■-■-■-■-• I
I
·-·-·
.,.
1·•
EXHIBIT E
MIXED USE OVERLAY SITES
THE FOLLOWING PARCELS ARE INCLUDED IN THE INTERNATIONAL WEST MIXED USE OVERLAY:
(NEW PARCELS ADDED IN BOLD-ITALICS)
APN# 101-011-06 APN# 231-561-14 APN# 101-080-63 APN# 100-352-20 APN# 101-080-68 APN# 101-080-64 APN# 100-130-67 APN# 100-130-66 APN# 231-491-12 APN# 231-491-13 APN# 231-491-14 APN# 231-491-15 APN# 231-451-40 APN# 231-451-38 APN# 231-451-37 APN# 231-451-36 APN# 100-130-56 APN# 101-611-78 APN# 100-130-71 APN# 100-345-23 APN# 101-681-22 APN# 101-642-02 APN# 101-452-02 APN# 100-335-25 APN# 101-611-02 APN# 100-335-34 APN# 100-335-37 APN# 100-130-72 APN# 100-335-30 APN# 100-130-74 APN# 100-130-73 APN# 101-642-01 APN# 101-080-71 APN# 101-080-73 APN# 101-080-74 APN# 231-441-36 APN# 100-347-15 APN# 231-405-01 APN# 100-122-33 APN# 101-080-76 APN# 100-345-21 APN# 101-311-25 APN# 101-343-65 APN# 231-441-35 APN# 101-011-02 APN# 101-315-33 APN# 231-422-14 APN# 231-422-07 APN# 231-422-12 APN# 231-422-15 APN# 231-423-09 APN# 231-422-09 APN# 231-423-08 APN# 231-422-08 APN# 231-422-22 APN# 231-422-21 APN# 231-422-20 APN# 231-422-19 APN# 231-422-18 APN# 231-422-17 APN# 231-422-16 APN# 231-422-11 APN# 231-423-15 APN# 231-423-16 APN# 231-423-14 APN# 231-423-13 APN# 231-423-12 APN# 231-423-11 APN# 231-423-10 APN# 231-422-10 APN# 231-423-02 APN# 231-423-01 APN# 231-423-03 APN# 231-423-04 APN# 231-423-05 APN# 231-423-06 APN# 231-423-07 APN# 101-311-17 APN# 101-011-03 APN# 101-311-19 APN# 101-311-24 APN# 101-311-21 APN# 101-311-20 APN# 100-123-01 APN# 100-123-02 APN# 101-611-01 APN# 100-130-79 APN# 101-343-66 APN# 100-130-58 APN# 101-011-04 APN# 100-130-68 APN# 101-011-01 APN# 100-130-69 APN# 101-080-75 APN# 231-323-20 APN# 100-122-32
EXHIBIT "A"
EXHIBIT E
MIXED USE OVERLAY SITES
THE FOLLOWING PARCEL S ARE INCLUDED IN THE INDUSTRIAL/RESIDENTIAL 1 MIXED USE OVERLAY:
(NEW PARCELS ADDED IN BOLD-ITALICS)
APN# 131-671-11 APN# 131-671-09 APN# 131-671-10 APN# 131-671-08 APN# 215-032-01 APN# 131-601-15 APN# 131-601-25 APN# 215-033-01 APN# 215-033-03 APN# 215-141-10 APN# 215-141-09 APN# 215-141-08 APN# 215-141-11 APN# 215-141-12 APN# 215-141-13 APN# 131-671-12 APN# 131-671-07 APN# 131-671-06
EXHIBIT "A"