DATE: August 20, 2024
TO: City Council
FROM: Director of Public Works
SUBJECT: Adopt a Resolution Approving the New Update to the Guidelines for Installation of Speed Humps
RECOMMENDATION
That the Council adopts a resolution (Attachment II) approving a new update to the Guidelines for Installation of Speed Humps (Attachment III).
SUMMARY
Staff recommend updating criteria relevant to Hayward’s traffic conditions and street characteristics. Recommended updates include:
Criteria
Existing
Proposed
2) 85th percentile speed
32 mph
30 mph
3) Street classification
Residential
Local and collector
7) Uninterrupted block length
750 feet
300 feet
9) Average daily traffic volume
Must range from 500 to 4,000 vehicles
Should range from 500 to 4,000 vehicles
11) Transit route
Prohibited
Possible, but requires coordination with AC Transit
14) 85th percentile guideline may be waived for schools For streets fronting schools
For streets within school zones defined by California Vehicle Code 16) Placement distance to intersections
250 feet
150 feet. 250 feet from intersection with arterial
20) Distance to driveways
Must be no closer than 10 feet
Should be no closer than 10 feet
21) Number of speed humps
Spacing should allow at least two speed humps on each block One speed hump is acceptable where other requirements preclude two 24) Placement with transit stops
N/A
No closer than 110 feet before and 30 feet after transit stop
BACKGROUND
First adopted by Council in December of 1995, the Guidelines for Installation of Speed Humps were proposed as a strategy to address concerns about speeding on public streets. The California State Traffic Control Devices Committee classifies speed humps as a “roadway design” feature, not a “traffic control" feature, which allows local jurisdictions to establish their own standards for their use. Hayward’s guidelines were developed to be similar to those of other nearby jurisdictions.
In 2001, Council asked Staff to revisit the criteria for minimum block length and maximum turning radius. The Guidelines for Installation of Speed Humps was revisited again in 2002 to provide flexibility for the installation of speed humps along bus routes in appropriate circumstances.
On July 3, 2018, Council adopted the Neighborhood Traffic Calming Program (NTCP) to establish a guide for City Staff, elected officials, and residents to implement proper and effective traffic calming solutions with community outreach and collaboration. Through the NTCP residents can apply for traffic calming treatments such as speed humps.
On April 24, 2024, Staff presented the proposed updates to the Council Infrastructure & Airport Committee who recommended submitting the update to Council for approval.
DISCUSSION
No major changes have been made to the Guidelines for Installation of Speed Humps since 2002. In that time, there have been at least two updates to Institute of Transportation Engineers’ (ITE’s) “Guide to Vertical Deflection Speed Reduction Techniques” with the most recent update in 2022. The ITE update focuses on current state-of-the-practice in the selection, design, and application of speed humps, speed tables, and other vertical deflection tools, based on data collected to evaluate traffic calming effectiveness over the past decade.
The proposed update to the City’s guidelines addresses lessons learned over the last decade and improves the organization of the guidelines. The recommended guidelines are categorized into two sections:
Street Geometry and Physical Characteristics
Speed Hump Placement
Street Geometry and Physical Characteristics
Staff recommend six revisions to the Street Geometry and Physical Characteristics. First, the current 85th percentile speed of traffic guideline requires that speed must be 32 mph or greater. ITE provides new safety-related speed metrics that can be used in place of the current 85th percentile guideline, which is more a measure of vehicle performance than neighborhood livability or safety. ITE states that a street may have a speeding problem if the 85th percentile speed is 5+ mph above the posted speed limit. Because speed humps are only allowed on 25 mph streets, staff is recommending reducing the City guideline to 30 mph. The updated guidelines also permit data collection from methods other than radar speed surveys.
The second revision replaces “residential” streets with “local or collector” streets for consistency with more precisely defined roadway classification systems.
Third, staff recommend reducing the minimum uninterrupted block length from 750 feet to 300 feet, unless the block intersects an arterial, in which case the minimum is 500 feet. Residential blocks in Hayward range from 250 to 1,200 feet and it is common in some neighborhoods to have sequential blocks under 500 feet in length. Restricting speed humps to longer blocks limits the City’s ability to reduce speeding in some neighborhoods and is inconsistent with practices used in other jurisdictions.
The fourth revision changes the language of the average daily traffic volume from “must” range from 500 to 4,000 vehicles per day to “should.” This allows flexibility for streets that meet all other guidelines but have slightly higher or lower traffic volume.
While AC Transit has demonstrated openness to context-appropriate traffic calming, speed humps can in some circumstances impact bus routes and transit riders. The fifth recommended update is to include a guideline for Staff to coordinate with AC Transit staff in these situations.
The last recommendation under this section replaces the 85th percentile speed requirement from “requests fronting schools” to “requests within a school zone as defined by the California Vehicle Code.” This provides consistency with other school traffic control measures and acknowledges that even streets that aren’t directly adjacent to schools can be important for school travel.
Speed Hump Placement
Under the Speed Hump Placement section, staff recommend four revisions. First, staff recommend reducing the minimum speed hump placement distance from local and collector street intersections from 250 feet to 150 feet. For streets that intersect with an arterial street, the minimum distance will stay at 250 feet. This is consistent with ITE recommendations to place speed humps 100 feet away from an intersection with a collector street and 250 feet from an intersection with a traffic signal. Arterial intersections present challenges for the safe and effective deployment of speed humps due to the higher posted speeds. However not every arterial intersection is signalized, so staff recommend expanding this guideline to apply to all arterial intersections, not only signalized intersections.
Second, staff recommend making the distance to driveways flexible by changing the language from “must” be no closer than 10 feet to “should” and including “when possible” to allow the use of speed humps on streets that meet all other guidelines but have an abundance of driveways without the required distance between them.
Third, staff recommend adding the phrase “it is preferable to install two humps on the same block but where other requirements would preclude two humps, one is acceptable” to clarify that a street may qualify if it can only fit one hump but that more than one is more effective in reducing speeding.
The last update includes distance requirements to bus stops as suggested by AC Transit for safe bus operations on streets with speed humps
ECONOMIC IMPACT
There will be no economic impact associated with this action.
FISCAL IMPACT
The expanded guidelines will result in more streets being eligible for speed humps. However, the existing Neighborhood Traffic Calming Program fund and Pavement Improvement Program fund is sufficient to accommodate this. Priority ranking of applications will be conducted if funding is not sufficient and staff will return to Committee and Council if necessary.
STRATEGIC ROADMAP
This agenda item supports the Strategy Priority of Invest in Infrastructure. Specifically, this update relates to Project N1: Continue to implement major corridor traffic calming initiatives.
SUSTAINABILITY FEATURES
There are no sustainability features associated with this action.
PUBLIC CONTACT
This update to the Guidelines for Installation of Speed Humps will expand the range of qualifying applications for speed humps that the City receives through the Neighborhood Traffic Calming Program. Applications are submitted by residents and require signatures from 25 percent of the residents fronting that street segment. Once the application is approved a petition for speed hump installation requires signatures from two-thirds of the residents on that street segment.
NEXT STEPS
If Council approves this update, more traffic calming applications will be eligible for speed humps.
Prepared by: Colin Patterson, Associate Transportation Planner Hugh Louch, Deputy Director of Public Works - Transportation Recommended by: Alex Ameri, Director of Public Works
Approved by:
_________________________________________
Dustin Claussen, Interim City Manager
https://hayward.legistar.com/LegislationDetail.aspx?ID=3542604&GUID=CD3CE8D9-375E-407D-9B82-C395D07B687A&Options=&Search= https://hayward.legistar.com/LegislationDetail.aspx?ID=6643502&GUID=5C9063A5-0471-4102-BCD3-152AF715BBD6&Options=&Search=