09.H Report Fire Rescue Vehicle 64 FD262 2026-08-18 — Pismo Beach City Council, August 18, 2026

PISMO BEACH CITY COUNCIL STAF REPOR
Agenda Item #9.H
Meetin Date: September 1, 2026

TITLE:

Purchase of a Type 6 Fire Rescue Squad Vehicle for the Fire Department RECOMMENDATION:

Adopt a Resolution authorizing the purchase of a 2026 Type 6 Fire Rescue Squad Vehicle from Fire Apparatus Solutions in the amount of $450,148.97.

DISCUSSION:

The City’s current Fire Rescue vehicle is a 2010 Ford F-450 XLT Supercab, which has reached the end of its optimal service life after 17 years of emergency response use. The life span of a Fire Rescue vehicle is typically 15 years due to increased maintenance needs, reduced reliability, and diminished operational efficiency, which can impact availability for emergency response. The proposed replacement vehicle (FD262) is a 2026 Ford Super Duty F-550 XLT configured as a Type 6 Fire Rescue Squad. The F-550 platform provides improved performance, enhanced payload capacity, and updated safety and emissions standards compared to the existing F-450, while maintaining the size and maneuverability necessary for a Type 6 response unit. This vehicle enhances the City’s ability to maintain a reliable and modern apparatus capable of meeting current and future operational demands.

The acquisition of a Type 6 Fire Rescue Squad will also provide greater operational flexibility and help ensure that the Fire Department has an appropriate response vehicle available for a wide range of incidents. The vehicle will support personnel and equipment during routine emergency operations while also serving as a valuable resource during larger or prolonged incidents, special events, and periods of increased emergency activity.

Fire Apparatus Solutions (FAS), an authorized Danko dealer, holds a current contract with the Helping Governments Across the Country Buy (HGACBuy) Cooperative Purchasing Program. This contrat was awarded through a competitively solicited process, allowing the City to streamline the procurement while obtaining competitively established pricing. The City’s Purchasing Policy and Procedures permit the use of cooperative purchasing agreements awarded through a competitive process.

Investing in this type of apparatus will complement the Department’s existing fleet, improve response efficiency, and provide a cost-effective means of expanding emergency response capabilities without relying solely on larger, more resource-intensive apparatus.

Staff therefore recommends moving forward with the purchase of a 2026 Ford Super Duty F-550 XLT Type 6 Fire Rescue Squad to support the City’s ongoing commitment to maintaining effective, reliable, and responsive fire and emergency services.

Council Agenda 9-1-2026 9.H-1

Conclusion and Recommendation
Staff recommends that the City Council adopt a resolution (Attachment 1) authorizing the award and purchase of a Type 6 Fire Rescue Squad to replace the existing vehicle from Fire Apparatus Solutions for $450,148.97.

FISCAL IMPACT:

The FY 2027 Motor Vehicle Replacement (MVR) Fund budget includes $500,000 to replace Rescue 64 (Vehicle number FD262) and additional equipment needed to place the vehicle into service.

The available FY 2026 budget and estimated costs are shown in Table 1.

Table 1: Budget and Cost of Proposed Vehicle Replacement Item Fiscal Impact
FY 2027 Bud et $500,000.00
Chassis purchase $425,148.97
Equipment and installation FAS 25,000.00
dditional Misc. equipment 49,851.03
Total Estimated Vehicle and Equipment Cost $500,000.00
Remainin Balance $0
ATTACHMENTS:

1. Resolution

2. Quote from Fire Apparatus Solutions

3. HGACBuy FS12-23 Contract worksheet

4. Sales Drawing
Prepared by:

Michelle Pearson, Analyst
Submitted by: Paul Provence, Battalion Chief
City Manager Approval:

Council Agenda 9-1-2026 9.H-2

RESOLUTION NO. R-2026-XXX

A RESOLUTION OF THE CITY COUNCIL OF THE CITY OF PISMO BEACH, CALIFORNIA AUTHORIZING THE PURCHASE OF A 2026 TYPE 6 FIRE RESCUE

SQUAD VEHICLE FROM FIRE APPARATUS SOLUTIONS IN THE AMOUNT OF $450,148.97
WHEREAS, the Fiscal Year (FY) 2027 Motor Vehicle Replacement (MVR) Fund budget includes $500,000 for the replacement of the Fire Department’s Rescue 64 and additional equipment needed to place the vehicle into service; and WHEREAS, due to the age of the vehicle, diminished operational efficiency, and reduced reliability, staff recommends replacing the current vehicle to enhance operational flexibility, provide updated safety and emissions standards, reduce maintenance costs, and support ongoing departmental needs; and
WHEREAS, staff has identified Fire Apparatus Solutions (FAS), an authorized Danko dealer in California, that holds a current contract with Helping Governments Across the Country Buy (HGACBuy) Cooperative Purchasing Program; this contract was awarded through a competitively solicited process and have been awarded a contract for Fire Rescue Squad vehicle; the City’s Purchasing Policy and Procedures permit the use of cooperative purchasing agreements awarded through a competitive process; and WHEREAS, the cost of the Type 6 Fire Rescue Squad including tax is $450,148.97 and the cost of additional equipment, electronics, decals, etc. needed to place the vehicle in to service is estimated to at $49,851.03, for a total estimated cost of $500,000.

NOW, THEREFORE, BE IT RESOLVED that the City Council of the City of Pismo Beach hereby authorizes the purchase of one 2026 Type 6 Fire Rescue Squad vehicle (FD262) from Fire Apparatus Solutions in the amount of $450,148.97, in accordance with the quotation attached to staff’s report dated September 1, 2026.

UPON MOTION OF Council Member , seconded by Council Member , the foregoing resolution was adopted by the City Council of the City of Pismo Beach this 1st day of September 2026, by the following vote:

AYES:

NOES:

ABSENT:

ABSTAIN:

RECUSED:

Attachment 1
Council Agenda 9-1-2026 9.H-3

________________________ ________________________
Ed Waage, Mayor Erica Kirkwood, City Clerk
IN WITNESS WHEREOF, I have hereunto set my hand and official seal of the City of Pismo Beach on _______________________.
________________________
Erica Kirkwood, City Clerk
Approved: Attest:

Attachment 1
Council Agenda 9-1-2026 9.H-4

Pismo Beach Rescue/Type 6
Sales Rep: Steve Langston
1762 South Sycamore Ave, Rialto, CA 92376
(1) Danko Type 6
(661) 301-7352 [email protected]
Equipment and Mounting
Chasiss Prepayment discount -$6,600.00
$415,842.00 x 1 $415,842.00

8.250%$34,306.97 x 1 $34,306.97
$450,148.97 x 1 $450,148.97
Tax rates are subject to change and the tax will be determined at the time of registration. Any changes to the price will be documented on a Change Order which may increase or decrease the price during the build process.

California Tire Fee is included. FAS will register the Vehicle. Pricing is good for 60 days. Fire Apparatus Agreement and or a Purchase Order needs to be submitted to Fire Apparatus Solutions. Signature below represents agreement to the Pricing and Terms listed above.

PROPOSAL
The expected build completion time is 485 days.

This purcahse will be made via the HGAC Contract# FS12-23.

Pretax Total
Sales Tax @
Total Purchase
$450,148.97
(1) Danko Type 6
Signing this agreement constitutes the purchase of (1) Danko Type 6 for the total cost of:

Pismo Beach Rescue/Type 6 Fire Apparatus Solutions
8/8/2026Steve Langston
Chassis prepayment will be $85,000 dollars,invoiced when delivered to Danko 8/8/2026fàxäx _tÇzáàÉÇ
Attachment 2
Council Agenda 9-1-2026 9.H-5

City of Pismo Beach Fire Department
Prepared For: Pismo Beach, CA
Vehicle: [Fleet] 2026 Ford Super Duty F-550 DRW (W5H) XLT 4WD Crew Cab 179" WB 60" CA Danko Emergency Equipment Co
Snyder, NE 68664
David Knobbe
Note:Photo may not represent exact vehicle or selected equipment.

Selected Model and Options
MODEL

CODE MODEL
W5H 2026 Ford Super Duty F-550 DRW XLT 4WD Crew Cab 179" WB 60" CA Vehicle: [Fleet] 2026 Ford Super Duty F-550 DRW (W5H) XLT 4WD Crew Cab 179" WB 60" CA ( Complete )
Prices, specifications, and availability are subject to change without notice, and do not include certain fees, taxes and charges that may be required by law or vary by manufacturer or region. Performance figures are guidelines only, and actual performance may vary. Photos may not represent actual vehicles or exact configurations. Content based on report preparer’s input is subject to the accuracy of the input provided. Data Version: 29199, Data updated Aug 4, 2026 1:51:00 AM UTC Aug 4, 2026 Page 2
COLORS

CODE DESCRIPTION
PQ Race Red

OPTIONS

CODE DESCRIPTION
99T Engine: 6.7L 4V OHV Power Stroke V8 Turbo Diesel B20 -inc: Operator Commanded Regeneration (OCR), Diesel Exhaust Fluid (DEF) tank and manual push-button engine-exhaust braking, 4.10 Axle Ratio 44G Transmission: TorqShift 10-Speed Automatic -inc: SelectShift, selectable drive modes: normal, tow/haul, eco, slippery roads and off-road and transmission power take-off provision (STD) 663A Order Code 663A -inc: 410 Amp Dual Alternators, 250 Amp + 160 Amp X4L Limited Slip w/4.30 Axle Ratio
64D Wheels: 19.5" x 6" Forged Polished Aluminum -inc: bright hub covers/center ornaments TGK Tires: 225/70Rx19.5G BSW Traction (TGK) -inc: 4 traction tires on the rear and 2 traction tires on the front, Not recommended for over the road applications; could incur irregular front tire wear and/or NVH PQ Race Red
3S Medium Dark Slate, Cloth 40/20/40 Split Bench Seat -inc: 20% center under-seat storage, center armrest, cupholder, storage, 2-way adjustable driver/passenger headrests and driver's side manual lumbar 47J Fire/Rescue Prep Pkg w/EPA Special Emissions -inc: upgraded front springs/GAWR rating, please see Supplemental Order Guide or visit fordbbas.com for complete details, Incomplete vehicle package - requires further manufacture and certification by a final stage manufacturer, Ford urges Fire/Rescue vehicle manufacturers to follow the recommendations of the Ford Incomplete Vehicle Manual and the Ford Truck Body Builders Layout Book (and pertinent supplements), Note 1: Stationary Elevated Idle Control (SEIC) has been integrated into the engine control module, Note 2: Engine calibration significantly reduces the possibility of depower mode when in stationary PTO operation, Note 3: Must meet the definition of an emergency vehicle, an Ambulance or Fire Truck per 40 CFR 86.1803.01 in the federal register, Note 4: California Code of Regulations allows for the sale of federally certified emergency vehicles in California, 410 Amp Dual Alternators, 250 Amp + 160 Amp 41H Engine Block Heater
67B 410 Amp Dual Alternators -inc: 250 Amp + 160 Amp
535 High Capacity Trailer Tow Package -inc: trailer brake wiring kit, Increases GCW from 32,500 lbs, to 40,000 lbs, Note: Salesperson's Portfolio or Trailer Towing Guide should be consulted for specific trailer towing or camper limits and corresponding required equipment, axle ratios and model availability, See Supplemental Reference for vehicle height consideration
86S Low Deflection Spacers -inc: 2" spacer blocks, Recommended for rear-biased loading, such as wrecker/retriever applications
41P Transfer Case Skid Plates
68M GVWR: 19,500 lb Payload Plus Upgrade Package 1 -inc: upgraded frame, upgraded rear-axle and low deflection/high capacity rear springs, Increases max RGAWR to 14,706 lbs, Note: See Order Guide Supplemental Reference for further details on GVWR
67P Extra Heavy-Duty Front End Suspension - 7,500 GAWR -inc: upgraded front axle and max 7,500 lbs, Front springs/GAWR rating for configuration selected, Incomplete vehicle package - requires further manufacture and certification by a final stage manufacturer
Attachment 2
Council Agenda 9-1-2026 9.H-6

OPTIONS

CODE DESCRIPTION
54F PowerScope Trailer Tow Mirrors w/Heat -inc: power-folding w/Autofold, telescoping, power glass, turn signal, high -intensity LED security approach lamps and utility lighting system (LED side-mirror spotlights) 166 Carpet Delete -inc: Replaced w/black flooring
872 Rear View Camera & Prep Kit -inc: Pre-installed content includes cab wiring and frame wiring to the rear most cross member, Upfitters kit includes camera w/mounting bracket, 20' jumper wire and camera mounting/aiming instructions
76C Exterior Backup Alarm (Pre-Installed)
Options Total
Standard Equipment
Mechanical
Engine: 7.3L 2V DEVCT NA PFI V8 Gas -inc: 410 Amp Dual Alternators, 250 Amp + 160 Amp (STD) Transmission: TorqShift 10-Speed Automatic -inc: SelectShift, selectable drive modes: normal, tow/haul, eco, slippery roads and off-road and transmission power take-off provision (STD)

4.88 Axle Ratio (STD)
50-State Emissions System
Transmission w/Driver Selectable Mode and Oil Cooler
Electronic Transfer Case
Part-Time Four-Wheel Drive
68-Amp/Hr 750CCA Maintenance-Free Battery w/Run Down Protection Dual 250 Amp Alternator
Trailer Wiring Harness
Towing Equipment -inc: Brake Controller and Trailer Sway Control 10520# Maximum Payload
GVWR: 18,000 lbs Payload Package
HD Gas-Pressurized Shock Absorbers
Front And Rear Anti-Roll Bars
Firm Suspension
Hydraulic Power-Assist Steering
40 Gal. Fuel Tank
Single Stainless Steel Exhaust
Dual Rear Wheels
Auto Locking Hubs
Vehicle: [Fleet] 2026 Ford Super Duty F-550 DRW (W5H) XLT 4WD Crew Cab 179" WB 60" CA ( Complete )
Prices, specifications, and availability are subject to change without notice, and do not include certain fees, taxes and charges that may be required by law or vary by manufacturer or region. Performance figures are guidelines only, and actual performance may vary. Photos may not represent actual vehicles or exact configurations. Content based on report preparer’s input is subject to the accuracy of the input provided. Data Version: 29199, Data updated Aug 4, 2026 1:51:00 AM UTC Aug 4, 2026 Page 4
Mechanical
Front Suspension w/Coil Springs
Solid Axle Rear Suspension w/Leaf Springs
4-Wheel Disc Brakes w/4-Wheel ABS, Front And Rear Vented Discs, Brake Assist, Hill Hold Control and Electric Parking Brake
Upfitter Switches
Exterior
Wheels: 19.5" x 6" Argent Painted Steel -inc: Hub covers/center ornaments not included (STD) Tires: 225/70Rx19.5G BSW A/P (STD)
Chrome Front Bumper w/Body-Colored Rub Strip/Fascia Accent and 2 Tow Hooks Black Fender Flares
Black Side Windows Trim and Black Front Windshield Trim Black Door Handles
Black Power Heated Side Mirrors w/Convex Spotter, Manual Folding and Turn Signal Indicator Manual Extendable Trailer Style Mirrors
Fixed Rear Window
Variable Intermittent Wipers
Deep Tinted Glass
Aluminum Panels
Front Splash Guards
Chrome Grille
Autolamp Auto On/Off Reflector Halogen Daytime Running Lights Preference Setting Headlamps w/Delay-Off Cab Clearance Lights
Perimeter/Approach Lights
Front Fog Lamps
Entertainment
Radio w/Seek-Scan, Clock, Speed Compensated Volume Control and Aux Audio Input Jack Radio: AM/FM Stereo w/MP3 Player -inc: 6 speakers and auxiliary audio input jack Fixed Antenna
6 Speakers
SYNC 4 w/8" Center Display -inc: wireless phone connection, cloud connected, AppLink w/app catalog, 911 Assist, Apple CarPlay and Android Auto compatibility and digital owner's manual Wireless Phone Connectivity
2 LCD Monitors In The Front
Attachment 2
Council Agenda 9-1-2026 9.H-7

Vehicle: [Fleet] 2026 Ford Super Duty F-550 DRW (W5H) XLT 4WD Crew Cab 179" WB 60" CA ( Complete )
Prices, specifications, and availability are subject to change without notice, and do not include certain fees, taxes and charges that may be required by law or vary by manufacturer or region. Performance figures are guidelines only, and actual performance may vary. Photos may not represent actual vehicles or exact configurations. Content based on report preparer’s input is subject to the accuracy of the input provided. Data Version: 29199, Data updated Aug 4, 2026 1:51:00 AM UTC Aug 4, 2026 Page 5
Interior
4-Way Driver Seat -inc: Manual Recline and Fore/Aft Movement 4-Way Passenger Seat -inc: Manual Recline and Fore/Aft Movement 60-40 Folding Split-Bench Front Facing Fold-Up Cushion Rear Seat Manual Tilt/Telescoping Steering Column
Gauges -inc: Speedometer, Odometer, Oil Pressure, Engine Coolant Temp, Tachometer, Transmission Fluid Temp, Engine Hour Meter, Trip Odometer and Trip Computer Power Rear Windows
Front Cupholder
Rear Cupholder
3 12V DC Power Outlets
Compass
Remote Keyless Entry w/Integrated Key Transmitter, Illuminated Entry and Panic Button Cruise Control w/Steering Wheel Controls
Manual Air Conditioning
HVAC -inc: Underseat Ducts
Locking Glove Box
Full Cloth Headliner
Urethane Gear Shifter Material
Interior Trim -inc: Metal-Look Instrument Panel Insert and Chrome Interior Accents Cloth 40/20/40 Split Bench Seat -inc: 20% center under-seat storage, center armrest, cupholder, storage, 2-way adjustable driver/passenger headrests and driver's side manual lumbar Day-Night Rearview Mirror
Driver And Passenger Visor Vanity Mirrors
Full Overhead Console w/Storage, 3 12V DC Power Outlets and 2 Interior 120V AC Power Outlets Front And Rear Map Lights
Full Carpet Floor Covering -inc: Carpet Front And Rear Floor Mats Smart Device Remote Engine Start
Smart Device Integration
Ford Connectivity Package (1-Year Included) -inc: unlimited Wi-Fi hotspot, Included for 1-year from warranty start date, Requires activation via Ford app w/credit card authorization; customer may cancel at any time, Evolving technology/cellular networks/vehicle capability may limit functionality and prevent operation of connected features, Ford may temporarily slow data speeds if such data usage reaches or exceeds 50GB within a billing cycle or due to network limitations, If a customer uses more than 50% of their data usage in a roaming country during a 60-day period, Ford may remove or limit the customer's data plan Instrument Panel Covered Bin, Dashboard Storage, Driver / Passenger And Rear Door Bins and Locking 1st Row Underseat Storage
Vehicle: [Fleet] 2026 Ford Super Duty F-550 DRW (W5H) XLT 4WD Crew Cab 179" WB 60" CA ( Complete )
Prices, specifications, and availability are subject to change without notice, and do not include certain fees, taxes and charges that may be required by law or vary by manufacturer or region. Performance figures are guidelines only, and actual performance may vary. Photos may not represent actual vehicles or exact configurations. Content based on report preparer’s input is subject to the accuracy of the input provided. Data Version: 29199, Data updated Aug 4, 2026 1:51:00 AM UTC Aug 4, 2026 Page 6
Interior
Power 1st Row Windows w/Driver And Passenger 1-Touch Up/Down Delayed Accessory Power
Power Door Locks w/Autolock Feature
Driver Information Center
Trip Computer
Outside Temp Gauge
Digital/Analog Appearance
Front Center Armrest w/Storage
Manual Adjustable Front Head Restraints and Manual Adjustable Rear Head Restraints Seats w/Cloth Back Material
2 Seatback Storage Pockets
Perimeter Alarm
Securilock Anti-Theft Ignition (pats) Immobilizer
Air Filtration
3 12V DC Power Outlets and 2 Interior 120V AC Power Outlets Safety-Mechanical
Driveline Traction Control
Safety-Exterior
Side Impact Beams
Safety-Interior
Dual Stage Driver And Passenger Seat-Mounted Side Airbags Emergency Sos Capability
Pre-Collision Assist with Automatic Emergency Braking (AEB) Lane Departure Warning
Collision Mitigation-Front
Tire Specific Low Tire Pressure Warning
Outboard Front Lap And Shoulder Safety Belts -inc: Height Adjusters Safety Canopy System Curtain 1st And 2nd Row Airbags
Dual Stage Driver And Passenger Front Airbags
Rear Child Safety Locks
Attachment 2
Council Agenda 9-1-2026 9.H-8

WARRANTY
Basic Years: 3
Basic Miles/km: 36,000
Drivetrain Years: 5
Drivetrain Miles/km: 60,000
Corrosion Years: 5
Corrosion Miles/km: Unlimited
Roadside Assistance Years: 5
Roadside Assistance Miles/km: 60,000
Technical Specifications
Powertrain
Transmission
Drivetrain Four Wheel Drive Trans Order Code 44G
Trans Type 10 Trans Description Cont.Automatic w/OD
Trans Description Cont. Again N/A First Gear Ratio (:1)4.62 Second Gear Ratio (:1)2.92 Third Gear Ratio (:1)2.13
Fourth Gear Ratio (:1)1.77 Fifth Gear Ratio (:1)1.52
Sixth Gear Ratio (:1)1.28 Reverse Ratio (:1)4.70
Clutch Size N/A Trans Power Take Off Yes
Final Drive Axle Ratio (:1)N/A Transfer Case Model Electronic Transfer Case Gear Ratio (:1), High N/A Transfer Case Gear Ratio (:1), Low N/A Transfer Case Power Take Off Yes Seventh Gear Ratio (:1)1.00 Eighth Gear Ratio (:1)0.85 Ninth Gear Ratio (:1)N/A
Tenth Gear Ratio (:1)N/A
Mileage
EPA Fuel Economy Est - Hwy N/A Cruising Range - City N/A EPA Fuel Economy Est - City N/A Fuel Economy Est-Combined N/A Cruising Range - Hwy N/A Estimated Battery Range N/A
Engine
Engine Order Code 99T Engine Type Intercooled Turbo
Diesel V-8
Displacement 6.7 L/406 Fuel System Direct Injection
SAE Net Horsepower @ RPM 330 @ 2200 SAE Net Torque @ RPM 950 @ 1800 Engine Oil Cooler No
Vehicle: [Fleet] 2026 Ford Super Duty F-550 DRW (W5H) XLT 4WD Crew Cab 179" WB 60" CA ( Complete )
Prices, specifications, and availability are subject to change without notice, and do not include certain fees, taxes and charges that may be required by law or vary by manufacturer or region. Performance figures are guidelines only, and actual performance may vary. Photos may not represent actual vehicles or exact configurations. Content based on report preparer’s input is subject to the accuracy of the input provided. Data Version: 29199, Data updated Aug 4, 2026 1:51:00 AM UTC Aug 4, 2026 Page 8
Powertrain
Electrical
Cold Cranking Amps @ 0° F (Primary) 750 Cold Cranking Amps @ 0° F (2nd)750 Cold Cranking Amps @ 0° F (3rd)N/A Maximum Alternator Capacity (amps) 250 & 160 Cooling System
Total Cooling System Capacity N/A
Traction Battery
Usable/net Traction Battery Capacity
(kWh)
N/A Gross Traction Battery Capacity (kWh) N/A
Vehicle
Emissions
Tons/yr of CO2 Emissions @ 15K mi/year N/A EPA Greenhouse Gas Score N/A Chassis
Weight Information
Standard Weight - Front 0.00 lbs Standard Weight - Rear 0.00 lbs Base Curb Weight 7438 lbs Gross Axle Wt Rating - Front 7000 lbs Gross Axle Wt Rating - Rear 14706 lbs Curb Weight - Front 4209 lbs Curb Weight - Rear 3189 lbs Option Weight - Front 587.00 lbs Option Weight - Rear 201.00 lbs Reserve Axle Capacity - Front 2204.00 lbs Reserve Axle Capacity - Rear 11316.00 lbs As Spec'd Curb Weight 8186.00 lbs As Spec'd Payload 11314.00 lbs Maximum Payload Capacity 12102.00 lbs Gross Combined Wt Rating 43000 lbs Gross Axle Weight Rating 21706.00 lbs Curb Weight 7398.00 lbs Reserve Axle Capacity 13520.00 lbs Total Option Weight 788.00 lbs Payload Weight Front 0 lbs Payload Weight Rear 0 lbs Gross Vehicle Weight Rating 19500.00 lbs Trailering
Dead Weight Hitch - Max Trailer Wt. 5000 lbs Dead Weight Hitch - Max Tongue Wt. 500 lbs Wt Distributing Hitch - Max Trailer Wt. 18500 lbs Wt Distributing Hitch - Max Tongue Wt. 1850 lbs Fifth Wheel Hitch - Max Trailer Wt.33400 lbs Fifth Wheel Hitch - Max Tongue Wt. 8350 lbs Maximum Trailering Capacity 18500 lbs
Attachment 2
Council Agenda 9-1-2026 9.H-9

Vehicle: [Fleet] 2026 Ford Super Duty F-550 DRW (W5H) XLT 4WD Crew Cab 179" WB 60" CA ( Complete )
Prices, specifications, and availability are subject to change without notice, and do not include certain fees, taxes and charges that may be required by law or vary by manufacturer or region. Performance figures are guidelines only, and actual performance may vary. Photos may not represent actual vehicles or exact configurations. Content based on report preparer’s input is subject to the accuracy of the input provided. Data Version: 29199, Data updated Aug 4, 2026 1:51:00 AM UTC Aug 4, 2026 Page 9
Chassis
Frame
Frame Type N/A Sect Modulus Rails Only N/A
Frame RBM N/A Frame Strength N/A
Frame Thickness N/A
Suspension
Suspension Type - Front Other Suspension Type - Rear Leaf Spring Capacity - Front 7000 lbs Spring Capacity - Rear 14706 lbs Axle Type - Front Non-Independent Axle Type - Rear Rigid Axle Axle Capacity - Front 7500 lbs Axle Capacity - Rear 14706 lbs Axle Ratio (:1) - Front 4.30 Axle Ratio (:1) - Rear 4.30 Shock Absorber Diameter - Front N/A Shock Absorber Diameter - Rear N/A Stabilizer Bar Diameter - Front N/A Stabilizer Bar Diameter - Rear N/A Tires
Front Tire Order Code TGK Rear Tire Order Code TGK
Spare Tire Order Code N/A Front Tire Size LT225/70SR19.5 Rear Tire Size LT225/70SR19.5 Spare Tire Size N/A
Front Tire Capacity 7500 lbs Rear Tire Capacity 15000 lbs Spare Tire Capacity N/A Revolutions/Mile @ 45 mph - Front 645 Revolutions/Mile @ 45 mph - Rear 645 Revolutions/Mile @ 45 mph - Spare N/A Wheels
Front Wheel Size 19.5 X 6 in Rear Wheel Size 19.5 X 6 in Spare Wheel Size N/A Front Wheel Material Forged Aluminum Rear Wheel Material Forged Aluminum Spare Wheel Material N/A Steering
Steering Type Re-Circulating
Ball
Steering Ratio (:1), Overall N/A
Steering Ratio (:1), On Center N/A Steering Ratio (:1), At Lock N/A Turning Diameter - Curb to Curb 51.1 ft Turning Diameter - Wall to Wall N/A Brakes
Brake Type 4-Wheel Disc Brake ABS System 4-Wheel
Vehicle: [Fleet] 2026 Ford Super Duty F-550 DRW (W5H) XLT 4WD Crew Cab 179" WB 60" CA ( Complete )
Prices, specifications, and availability are subject to change without notice, and do not include certain fees, taxes and charges that may be required by law or vary by manufacturer or region. Performance figures are guidelines only, and actual performance may vary. Photos may not represent actual vehicles or exact configurations. Content based on report preparer’s input is subject to the accuracy of the input provided. Data Version: 29199, Data updated Aug 4, 2026 1:51:00 AM UTC Aug 4, 2026 Page 10
Chassis
Brakes
Brake ABS System (Second Line)4-Wheel Disc - Front (Yes or )Yes Disc - Rear (Yes or )Yes Front Brake Rotor Diam x Thickness 15.4 in Rear Brake Rotor Diam x Thickness 15.8 in Drum - Rear (Yes or )N/A Rear Drum Diam x Width N/A
Fuel Tank
Fuel Tank Capacity, Approx 40 gal Aux Fuel Tank Capacity, Approx N/A Fuel Tank Location N/A Aux Fuel Tank Location N/A
Dimensions
Interior Dimensions
Passenger Capacity 6 Front Head Room 40.8 in
Front Leg Room 43.9 in Front Shoulder Room 66.7 in
Front Hip Room 62.5 in Second Head Room 40.4 in
Second Leg Room 43.6 in Second Shoulder Room 65.9 in
Second Hip Room 64.7 in
Exterior Dimensions
Wheelbase 179 in Length, Overall w/o rear bumper N/A
Length, Overall w/rear bumper N/A Length, Overall 265.2 in Width, Max w/o mirrors 80 in Height, Overall 82.8 in
Overhang, Front 38.3 in Overhang, Rear w/o bumper 47.2 in Front Bumper to Back of Cab N/A Cab to Axle 60 in
Cab to End of Frame 107.2 in Ground to Top of Load Floor N/A Ground to Top of Frame N/A Frame Width, Rear 34.2 in
Ground Clearance, Front 8.6 in Ground Clearance, Rear 8.6 in Body Length 0.00 ft Cab to Body N/A
Cargo Area Dimensions
Cargo Box Width @ Top, Rear N/A Cargo Box Width @ Floor N/A Cargo Box Width @ Wheelhousings N/A Cargo Box (Area) Height N/A Tailgate Width N/A Cargo Volume N/A
Ext'd Cab Cargo Volume N/A
Attachment 2
Council Agenda 9-1-2026 9.H-10

WEIGHT RATINGS
Front Gross Axle Weight Rating:7000 lbs
Rear Gross Axle Weight Rating:14706 lbs
Gross Vehicle Weight Rating:19500.00 lbs
Optional Equipment
ENGINE

CODE DESCRIPTION
99N Engine: 7.3L 2V DEVCT NA PFI V8 Gas -inc: 410 Amp Dual Alternators, 250 Amp + 160 Amp (STD)
99T Engine: 6.7L 4V OHV Power Stroke V8 Turbo Diesel B20 -inc: Operator Commanded Regeneration (OCR), Diesel Exhaust Fluid (DEF) tank and manual push-button engine- exhaust braking, 4.10 Axle Ratio

TRANSMISSION

CODE DESCRIPTION
44G Transmission: TorqShift 10-Speed Automatic -inc: SelectShift, selectable drive modes: normal, tow/haul, eco, slippery roads and off-road and transmission power take-off provision (STD)

OPTION PACKAGE

CODE DESCRIPTION
663A Order Code 663A -inc: 410 Amp Dual Alternators, 250 Amp + 160 Amp

AXLE RATIO

CODE DESCRIPTION
X41 4.10 Axle Ratio
X48 4.88 Axle Ratio (STD)
X4L Limited Slip w/4.30 Axle Ratio
X4N Limited Slip w/4.10 Axle Ratio
X8L Limited Slip w/4.88 Axle Ratio
WHEELS

CODE DESCRIPTION
64D Wheels: 19.5" x 6" Forged Polished Aluminum -inc: bright hub covers/center ornaments 64Z Wheels: 19.5" x 6" Argent Painted Steel -inc: Hub covers/center ornaments not included (STD) TIRES

CODE DESCRIPTION
TGJ Tires: 225/70Rx19.5G BSW A/P (STD)
Vehicle: [Fleet] 2026 Ford Super Duty F-550 DRW (W5H) XLT 4WD Crew Cab 179" WB 60" CA ( Complete )
Prices, specifications, and availability are subject to change without notice, and do not include certain fees, taxes and charges that may be required by law or vary by manufacturer or region. Performance figures are guidelines only, and actual performance may vary. Photos may not represent actual vehicles or exact configurations. Content based on report preparer’s input is subject to the accuracy of the input provided. Data Version: 29199, Data updated Aug 4, 2026 1:51:00 AM UTC Aug 4, 2026 Page 12
TIRES

CODE DESCRIPTION
TGK Tires: 225/70Rx19.5G BSW Traction (TGK) -inc: 4 traction tires on the rear and 2 traction tires on the front, Not recommended for over the road applications; could incur irregular front tire wear and/or NVH
TGM Tires: 225/70Rx19.5G BSW Traction -inc: 4 traction tires on the rear and 2 A/P tires on the front

PRIMARY PAINT

CODE DESCRIPTION
AT Yellow
BY School Bus Yellow
DR Avalanche
E4 Vermillion Red
E9 Argon Blue Metallic
GR Green
JS Iconic Silver Metallic
M7 Carbonized Gray Metallic
MB Orange
PQ Race Red
RR Ruby Red Metallic Tinted Clearcoat
T9 Marsh Gray
UM Agate Black Metallic
W6 Green Gem
Z1 Oxford White

SEAT TYPE

CODE DESCRIPTION
2J Baja, Cloth 40/Console/40 Front Seats -inc: 2-way adjustable driver/passenger headrests and driver's side manual lumbar, Flow-Through Console, Pro Power Onboard - 400W outlet in rear 2S Medium Dark Slate, Cloth 40/Console/40 Front Seats -inc: 2-way adjustable driver/passenger headrests and driver's side manual lumbar, Flow-Through Console, Pro Power Onboard - 400W outlet in rear
3J Baja, Cloth 40/20/40 Split Bench Seat -inc: 20% center under-seat storage, center armrest, cupholder, storage, 2-way adjustable driver/passenger headrests and driver's side manual lumbar
3S Medium Dark Slate, Cloth 40/20/40 Split Bench Seat -inc: 20% center under-seat storage, center armrest, cupholder, storage, 2-way adjustable driver/passenger headrests and driver's side manual lumbar
Attachment 2
Council Agenda 9-1-2026 9.H-11

ADDITIONAL EQUIPMENT - PACKAGE

CODE DESCRIPTION
17V XLT Value Package -inc: Power Adjustable Pedals, Electrochromic Rear View Mirror, Heated Driver's Seat, 8-Way Power Driver's Seat, Remote Start, Autolock/Auto Unlock, Rear Window Defroster
47A Ambulance Prep Package -inc: upgraded front springs/GAWR rating, please see Supplemental Order Guide or visit fordbbas.com for complete details, Incomplete vehicle package - requires further manufacture and certification by a final stage manufacturer, Ford vehicles are suitable for producing ambulances only if equipped w/the Ford Ambulance Prep Package, In addition, Ford urges ambulance manufacturers to follow the recommendations of the Ford Incomplete Vehicle Manual and the Ford Truck Body Builders Layout Book (and pertinent supplements), Using a Ford vehicle without the Ford Ambulance Prep Package to produce an ambulance voids the Ford warranty, Note: Stationary Elevated Idle Control (SEIC) has been integrated into the engine control module, 410 Amp Dual Alternators, 250 Amp + 160 Amp
47J Fire/Rescue Prep Pkg w/EPA Special Emissions -inc: upgraded front springs/GAWR rating, please see Supplemental Order Guide or visit fordbbas.com for complete details, Incomplete vehicle package - requires further manufacture and certification by a final stage manufacturer, Ford urges Fire/Rescue vehicle manufacturers to follow the recommendations of the Ford Incomplete Vehicle Manual and the Ford Truck Body Builders Layout Book (and pertinent supplements), Note 1: Stationary Elevated Idle Control (SEIC) has been integrated into the engine control module, Note 2: Engine calibration significantly reduces the possibility of depower mode when in stationary PTO operation, Note 3: Must meet the definition of an emergency vehicle, an Ambulance or Fire Truck per 40 CFR 86.1803.01 in the federal register, Note 4: California Code of Regulations allows for the sale of federally certified emergency vehicles in California, 410 Amp Dual Alternators, 250 Amp + 160 Amp 47L Ambulance Prep Pkg w/Special Emissions -inc: upgraded front springs/GAWR rating, please see Supplemental Order Guide or visit fordbbas.com for complete details, Incomplete vehicle package - requires further manufacture and certification by a final stage manufacturer, Ford vehicles are suitable for producing ambulances w/special emissions only if equipped w/the Ford Ambulance Prep Package w/EPA Special Emergency Vehicle Emissions, In addition, Ford urges ambulance manufacturers to follow the recommendations of the Ford Incomplete Vehicle Manual and the Ford Truck Body Builders Layout Book (and pertinent supplements), Using a Ford vehicle without the Ford Ambulance Package w/EPA Special Emergency Vehicle Emissions to produce an ambulance w/special emissions voids the Ford warranty, Note 1:

Stationary Elevated Idle Control (SEIC) has been integrated into the engine control module, Note 2: Engine calibration significantly reduces the possibility of depower mode when in stationary PTO operation, Note 3: Must meet the definition of an Emergency Vehicle, an Ambulance or Fire Truck per 40 CFR 86.1803.01 in the Federal Register, Note 4: California Code of Regulations allows for the sale of federally certified emergency vehicles in California, 410 Amp Dual Alternators, 250 Amp + 160 Amp

ADDITIONAL EQUIPMENT - MECHANICAL

CODE DESCRIPTION
41H Engine Block Heater
41P Transfer Case Skid Plates
Vehicle: [Fleet] 2026 Ford Super Duty F-550 DRW (W5H) XLT 4WD Crew Cab 179" WB 60" CA ( Complete )
Prices, specifications, and availability are subject to change without notice, and do not include certain fees, taxes and charges that may be required by law or vary by manufacturer or region. Performance figures are guidelines only, and actual performance may vary. Photos may not represent actual vehicles or exact configurations. Content based on report preparer’s input is subject to the accuracy of the input provided. Data Version: 29199, Data updated Aug 4, 2026 1:51:00 AM UTC Aug 4, 2026 Page 14

ADDITIONAL EQUIPMENT - MECHANICAL

CODE DESCRIPTION
473 Snow Plow Prep Package -inc: pre-selected springs (see order guide supplemental reference for springs/FGAWR of specific vehicle configurations), Note 1: Restrictions apply; see supplemental reference or body builders layout book for details, Note 2: Also allows for the attachment of a winch, Note 3: Highly recommended to add (86M) dual battery on 7.3L gas engine, Adding (67B) 410 amp dual alternators for diesel engine is highly recommended for max power output
535 High Capacity Trailer Tow Package -inc: trailer brake wiring kit, Increases GCW from 32,500 lbs, to 40,000 lbs, Note: Salesperson's Portfolio or Trailer Towing Guide should be consulted for specific trailer towing or camper limits and corresponding required equipment, axle ratios and model availability, See Supplemental Reference for vehicle height consideration 65C Dual Diesel Fuel Tanks -inc: Combines 40 gallon aft-of-axle and 26.5 gallon mid ship tank 65M 26.5 Gallon Mid Ship Fuel Tank -inc: Removes 40 gallon fuel tank 67A 350 Amp Dual Alternators -inc: 190 Amp + 160 Amp
67B 410 Amp Dual Alternators -inc: 250 Amp + 160 Amp
67H Heavy-Service Front Suspension Package -inc: pre-selected heavy-service front springs (see Order Guide Supplemental Reference for springs/FGAWR of specific vehicle configurations), Recommended only on vehicles which will permanently utilize aftermarket equipment such as heavy-duty winches, brush guards or other apparatus which loads the front axle to the specified Gross Axle Weight Rating (GAWR), Note 1: May result in a deterioration of ride quality, Note 2: Vehicle ride height will increase w/the addition of this package 67P Extra Heavy-Duty Front End Suspension - 7,500 GAWR -inc: upgraded front axle and max 7,500 lbs, Front springs/GAWR rating for configuration selected, Incomplete vehicle package - requires further manufacture and certification by a final stage manufacturer 67X Extra Heavy-Service Suspension Package -inc: pre-selected extra heavy-service front springs (see Order Guide Supplemental Reference for springs/FGAWR of specific vehicle configurations), Recommended only on vehicles which will permanently utilize aftermarket equipment such as heavy-duty winches, brush guards or other apparatus which loads the front axle to the specified Gross Axle Weight Rating (GAWR), Note 1: May result in a deterioration of ride quality, Note 2: Vehicle ride height will increase w/the addition of this package 68D GVWR: 17,500 lb Payload Downgrade Package
68H GVWR: 19,550 lb Payload Plus Upgrade Package 2 -inc: upgraded frame, upgraded rear-axle and low deflection/high capacity rear springs, Increases max RGAWR to 14,706 lbs, Note: See Order Guide Supplemental Reference for further details on GVWR 68M GVWR: 19,500 lb Payload Plus Upgrade Package 1 -inc: upgraded frame, upgraded rear-axle and low deflection/high capacity rear springs, Increases max RGAWR to 14,706 lbs, Note: See Order Guide Supplemental Reference for further details on GVWR 86K Programmable Engine Idle Shutdown Timer -inc: Selection of this option enables the driver to select a time period between 1 to 30 minutes before the engine will shut off after idling, There will not be an option to override this timing, Customers needing to idle their vehicles for longer periods should not select this option
86S Low Deflection Spacers -inc: 2" spacer blocks, Recommended for rear-biased loading, such as wrecker/retriever applications
927 Speed Limitation - 75-MPH Governed Top Speed
Attachment 2
Council Agenda 9-1-2026 9.H-12

ADDITIONAL EQUIPMENT - EXTERIOR

CODE DESCRIPTION
153 Front License Plate Bracket
18B Platform Running Boards
512 Spare Tire & Wheel -inc: Excludes carrier, 6-Ton Hydraulic Jack 51D Spare Tire & Wheel Delete *CREDIT*
54F PowerScope Trailer Tow Mirrors w/Heat -inc: power-folding w/Autofold, telescoping, power glass, turn signal, high-intensity LED security approach lamps and utility lighting system (LED side-mirror spotlights)
59H Center High-Mounted Stop Lamp (CHMSL)
61J 6-Ton Hydraulic Jack
61L Front Wheel Well Liner (Pre-Installed)
91G Amber-Wht 360-Deg Dual Beacon LED Warning Strobes -inc: Pre-installed 91S Amber 360-Degree Dual Beacon LED Warning Strobes -inc: Pre-installed 945 Stainless Steel Wheel Covers (Pre-Installed) -inc: Front and rear

ADDITIONAL EQUIPMENT - INTERIOR

CODE DESCRIPTION
166 Carpet Delete -inc: Replaced w/black flooring
16T All-Weather Floor Mats w/o Carpet (Pre-Installed)
21X Vehicle Safe by Console Vault (Pre-Installed)
41A Rapid-Heat Supplemental Cab Heater -inc: 410 Amp Dual Alternators, 250 Amp + 160 Amp 43K Pro Power Onboard - 2kW -inc: dual alternators 12V 250 Amp + 24V 150 Amp, Placement and connection of the aux outlet is the responsibility of the final stage manufacturer 52S Interior Work Surface
76C Exterior Backup Alarm (Pre-Installed)
872 Rear View Camera & Prep Kit -inc: Pre-installed content includes cab wiring and frame wiring to the rear most cross member, Upfitters kit includes camera w/mounting bracket, 20' jumper wire and camera mounting/aiming instructions

ADDITIONAL EQUIPMENT - OTHER

CODE DESCRIPTION
56M Ford US National Fleet Incentives *CREDIT*
79V COV Required *PRICE TO FOLLOW*
___ Fleet Advertising Credit *CREDIT*
C09 Priced DORA
Vehicle: [Fleet] 2026 Ford Super Duty F-550 DRW (W5H) XLT 4WD Crew Cab 179" WB 60" CA ( Complete )
Prices, specifications, and availability are subject to change without notice, and do not include certain fees, taxes and charges that may be required by law or vary by manufacturer or region. Performance figures are guidelines only, and actual performance may vary. Photos may not represent actual vehicles or exact configurations. Content based on report preparer’s input is subject to the accuracy of the input provided. Data Version: 29199, Data updated Aug 4, 2026 1:51:00 AM UTC Aug 4, 2026 Page 16

DEALER INSTALLED OPTIONS

CODE DESCRIPTION
___First Aid Kit w/Ford Logo -inc: Shipped separately from the vehicle for dealer installation ___Illuminated Front Emblem -inc: Shipped separately from the vehicle for dealer installation ___Kicker Subwoofer -inc: Shipped separately from the vehicle for dealer installation ___Roadside Assistance Kit w/Ford Logo -inc: Shipped separately from the vehicle for dealer installation
___SecuriCode Wireless Keyless Entry Keypad -inc: Driver's side, Shipped separately from the vehicle for dealer installation
___Smoke Side Window Deflector Kit (Set of 4) -inc: Low profile by Lund, Shipped separately from the vehicle for dealer installation
___Super Duty Tool Kit by AllTrade -inc: Shipped separately from the vehicle for dealer installation ___Windshield Sunshade by Covercraft -inc: Shipped separately from the vehicle for dealer installation

SHIP THRU CODES

CODE DESCRIPTION
311 Ship-Thru: Dejana
312 Ship-Thru: National Fleet Services
313 Ship-Thru: Brice Equipment
314 Ship-Thru: Reading Equipment & Distribution
315 Ship-Thru: Alt Fuel Innovations, LLC (AFI)
319 Ship-Thru: KC Truck Systems Inc.
31A Ship-Thru: Altec
31B Ship-Thru: Reading Equipment
31C Ship-Thru: Zoresco Equipment
31G Ship-Thru: NBC Truck Equipment
31H Ship-Thru: Manning Truck Equipment
31K Ship-Thru: Adrian Steel
31L Ship-Thru: Holman
31M Ship-Thru: Manning Truck Equipment
31N Ship-Thru: Monroe Truck Equipment
31P Ship-Thru: Roush CleanTech
31S Ship-Thru: Reading Equipment
31T Ship-Thru: Bobs Services LLC
31U Ship-Thru: General Truck Body
Attachment 2
Council Agenda 9-1-2026 9.H-13

SHIP THRU CODES

CODE DESCRIPTION
31V Ship-Thru: Knapheide Truck Equipment
31W Ship-Thru: Knapheide - IN
31Y Ship Thru: Zoresco Equipment
31Z Ship-Thru: Knapheide
D9D Built: Ohio Plant
D9E Built: Kentucky Truck Plant

CITY OF PISMO BEACH FIRE DEPARTMENT

PISMO BEACH, CA
08/04/26 Page 1 of 34

DANKO QUICK ATTACK
NFPA 1900 COMPLIANCE
The NFPA 1900 “Standard for Aircraft Rescue and Firefighting Vehicles, Automotive Fire Apparatus, Wildland Fire Apparatus, and Automotive Ambulances" 2024 Edition are hereby adopted and made a part of these specifications, the same as if it were written out in full detail.

Should any area, section or portion of the apparatus not meet the intent and applicable requirements of NFPA 1900; a clearly defined listing or explanation of what and or why compliance was not achieved shall be written within these specifications.

The manufacturer shall provide any equipment written within these specifications to be included with the completed apparatus.

DRAWINGS
A detailed drawing that represents the apparatus as described herein shall be provided with these specifications. Generic layouts or drawings of similar apparatus shall not be acceptable.

VEHICLE STABILITY
The apparatus shall comply with the vehicle stability requirements of the 2024 edition of NFPA 1900 section 7.14.3.

HIGHWAY PERFORMANCE
The apparatus shall be tested at its estimated in-service weight to verify the NFPA 1900 section 7.16 Highway Performance and 7.18 General Pre-Delivery Tests are met for the apparatus prior to delivery.

TIRE PRESSURE INDICATING VALVE CAPS
No pressure indicating valve caps shall be provided.

PERMANENT FLUID PLATE
A permanent plate shall be affixed to the completed apparatus specifying the quantity and type of the following fluids that may be used in the apparatus for normal maintenance. Where a fluid is not applicable to the unit, the plate shall be marked N/A to inform a service technician who may not be familiar with the apparatus.

APPARATUS FLUIDS
Attachment 2
Council Agenda 9-1-2026 9.H-14

CITY OF PISMO BEACH FIRE DEPARTMENT

PISMO BEACH, CA
08/04/26 Page 2 of 34
** Sample label for reference only
NFPA 1900 required safety signs shall be placed as needed on the apparatus to meet compliance.

CHASSIS
The chassis shall be a Ford Super Duty F-550 crew cab.

Any factory parts removed from the chassis and replaced shall not be returned to the customer unless otherwise specified.

The chassis engine shall be diesel powered.

At time of delivery at the factory the completed apparatus shall be full of diesel and DEF (urea) and all fluid levels checked.

CLEAN & DETAIL APPARATUS
At time of delivery at the factory the completed apparatus shall be cleaned and detailed both inside and out.

FUEL FILL
A diesel fuel fill pocket flange shall be supplied and mounted at the rear of the body.

DEF TANK FILL
The DEF (urea) tank fill shall be mounted on the left side of the apparatus at the front of the body.

CHASSIS AUTOMATIC HIGH IDLE
The chassis shall be provided with a SEIC (Stationary Engine Idle Control) system from Ford. The SEIC shall automatically engage high idle when the chassis detects a significant voltage drop and the transmission is in park.

INTERIOR CAB LIGHTING
There shall be two (2) Whelen 70CREGCS combination red/clear dome lights provided and installed in the chassis cab, one above driver seat and one above passenger seat.

The switch to operate each light will be located near light.

BACKUP ALARM
The chassis shall be equipped with a backup alarm. The backup alarm shall be provided and installed on the chassis by the chassis manufacturer. The backup alarm shall provide an audible alert any time the transmission is shifted into reverse.

The back up alarm shall have a "disabled" switch located on the custom console.

OEM PAINTED CHASSIS CAB
The chassis cab shall be painted standard OEM red from the chassis manufacturer.

OEM CHASSIS RIMS
The wheel rims shall be as stated in the chassis specifications unless otherwise noted.

FRONT BUMPER REPLACEMENT
The chassis front bumper shall be replaced with a Fab Four Premium black steel front bumper.

The aftermarket bumper shall be provided with tow hooks.

The Fab Fours bumper shall be provided with a winch plate capable of handling a 16,500 lb winch. The winch plate shall have a gloss black powder coat finish.

WARN 16.5ti WINCH
A Warn 16.5ti heavy weight series winch shall be supplied and installed at the front of the apparatus.

This winch features a gear ratio of 315:1, high strength carrier plates to handle the gear train stresses and a single-line pulling capacity of up to 16,500 lbs. The winch shall be provided with 90 feet of 7/16" wire rope, and fairlead roller to reduce wire wear.

The winch will also be supplied with a 12' controller lead featuring a thermometric indicator.

SPOT/FLOOD LIGHT
There shall be a HiViz model FT-MB-15-F-B black spot/flood combo installed on the front bumper replacement grille and controlled by a switch in the cab.

INVERTER / BATTERY CHARGER
There shall be a Xantrex Freedom XC 1000W inverter/charger model 817-1050-11 installed on the apparatus. The Freedom XC is a compact automatic 3 stage battery charger and 1000 watt continuous/2000 watt surge pure sine wave inverter with 8.4A continuous output and a peak conversion efficiency of 91%. The inverter has an extended 2 second surge rating of 2000W to meet the power needs of all sorts of demanding loads without putting the equipment at risk.

The inverter/charger shall have a built in 30A transfer relay. The transfer relay automatically transfers any connected loads to receive power from either the chassis or the shoreline when it is connected.

There shall be a built in 20A GFCI duplex outlet provided on the inverter/charger.

Attachment 2
Council Agenda 9-1-2026 9.H-15

CITY OF PISMO BEACH FIRE DEPARTMENT

PISMO BEACH, CA
08/04/26 Page 4 of 34

SUPER AUTO EJECT SHORELINE RECEPTACLE
A Kussmaul model 091-55-15-120 Super Auto Eject 120-volt shoreline receptacle shall be installed on the left side of the apparatus and connected to the battery charger.

When the vehicle is started the shoreline shall automatically eject to prevent the vehicle from being moved while still connected.

An industrial grade 120-volt connector designed to function with the super auto eject shall be provided.

DELUXE COVER WITH INDICATOR DISPLAY
The Super Auto Eject shall be supplied with a Deluxe cover that incorporates an OLED display along with a weatherproof cover. The Deluxe cover shall display the volts and amps of the inverter battery and indicate status of the inverter.

The color of the Deluxe cover shall be RED unless otherwise specified. 120 VOLT RECEPTACLE OUTLET STRIP(S)
One (1) outlet strip(s) shall be installed on the apparatus and wired in conjunction with the inverter/charger. Each outlet strip shall have three (3) 15A duplex outlets for a total of six (6) individual outlets.

The outlet strip(s) location shall be as follows:

L3 Compartment on rear bulkhead as high as possible.

RETRACTABLE RUNNING BOARDS
One (1), set of Amp Research PowerStep Xtreme retractable powered running boards shall be supplied and installed on the chassis. These running boards conveniently extend when the cab door is opened and retract when the door is closed.

Featuring heavy duty dual electric motors to quickly deploy and retract the running boards and manufactured with high strength die-cast aluminum components with a military grade PTFE corrosion resistant powder coating these running boards can support up to 600 lbs per side. Includes anti-pinch technology to prevent injury or motor burnout.

Note: The Amp Research running boards will not carry any factory warranty due to them being installed on a F- 550 Super Duty chassis which is not factory approved by Amp research.

APPARATUS BODY
The apparatus body shall be designed to mount on a 60" cab to axle chassis. The body shall have overall dimensions of 96" wide x 120" long with a height of 68".

FRAME AND CROSS MEMBERS
The complete body shall be of a modular design consisting of independent body modules and/or subassemblies and welded to an independent heavy duty support framework. The main body frame rails shall consist of extruded square tubing 2" x 2" x 1/4" wall and extruded angle 2" x 2" x 1/4" thick.

The cross members shall extend the full width of the body to support the compartments. There shall be a minimum of four (4) cross members spaced from front to rear.

This uniform method of construction forms the aluminum into a strong, yet flexible structure.

ELECTRICAL ACCESS PANELS
The rear wall of the rear compartments shall have removable access panels constructed of aluminum treadbrite, to cover and protect all electrical accessories, lights, and wiring mounted at the rear of the apparatus. The panels shall be easily removable to provide access if needed.

GRAVEL SHIELD
There shall be a 1/8" treadbrite aluminum gravel shield attached to the front, outer edges of the apparatus body extending the full height of the body. The gravel shield shall provide protection to help reduce potential damage to the paint from road debris.

RUB RAILS
Aluminum rub rails 1-1/2" wide x 3/8" thick, to be furnished below the front and rear compartment doors on both sides of the apparatus body. The rub rails to be spaced 3/4" from the body enabling shock absorbency and cleaning ease. Spacers shall be nylon, with counter sunk stainless steel bolt fasteners for easy replacement.

REAR FENDER WELLS
The rear fender wells shall be constructed of smooth, painted aluminum with a heavy-duty, extruded aluminum fenderette. A circular smooth aluminum inner wheel liner shall be furnished for each fender providing an easy to clean area. Sufficient clearance shall be provided to allow for the use of tire chains when the apparatus is fully loaded.

BODY FASTENERS
The body shall be fastened to the chassis frame in a minimum of 6 locations. There shall be two (2) spring loaded fastening points at the front to allow flexing as well as two rigid fasteners near the center and two at the rear.

MUD FLAPS
Two (2), mud flaps shall be supplied and mounted one on each side behind the rear wheels.

Attachment 2
Council Agenda 9-1-2026 9.H-16

CITY OF PISMO BEACH FIRE DEPARTMENT

PISMO BEACH, CA

08/04/26 Page 6 of 34

TAILBOARD
The tailboard shall be bolted to the receiver assembly to allow for easy replacement if damaged. The tailboard shall be 8" in depth and 88" wide, with a space between the body and the tailboard to allow for easy cleaning. The framework shall be covered with .125" embossed aluminum treadbrite.

TOW EYES
There shall be two (2) tow eyes located at the rear of the apparatus near the rear receiver. The tow eyes shall be constructed of plate steel.

REAR RECEIVER TUBE
There shall be a 2" class 5 receiver tube located at the rear of the apparatus with two safety chain attachment points. The receiver tube shall be rated at 12,000 .lb gross trailer weight and 1,200 .lb maximum tongue weight.

A label shall be placed near the receiver stating the gross trailer weight, and tongue weight.

TRAILER ELECTRICAL PLUG
One (1), 7-prong blade connector with a weatherproof cover shall be supplied and mounted near the rear receiver tube.

LEFT SIDE RECEIVER TUBE
A 2" receiver tube shall be installed on the left side of the apparatus. The receiver shall be bolted directly to the chassis frame rail. The receiver tube shall not be rated.

No power provided.

RIGHT SIDE RECEIVER TUBE
A 2" receiver tube shall be installed on the left side of the apparatus. The receiver shall be bolted directly to the chassis frame rail. The receiver tube shall not be rated.

No power provided.

BODY & COMPARTMENT CONSTRUCTION- SMOOTH ALUMINUM
The entire body shall be constructed of smooth aluminum with all major structural body supports, panels, and compartment floors being fabricated from 3/16" (.1875) smooth aluminum sheets.

All body compartments shall properly sealed to keep dirt and water from entering and shall have smooth aluminum sweep-out floors.

COMPARTMENT VENTING
Body compartments shall be vented as needed to allow doors to properly open and close. The vents shall be mounted in a manner that will reduce the amount of dirt and water that may enter the compartment.

COMPARTMENT DRAIN HOLES
Each compartment shall be have drain holes to allow standing water to exit the compartment.

COMPARTMENT LIGHTING
Each lighted compartment shall be lit with a rugged LED strip light; running vertically along the compartment door opening and activated by an automatic switch. This style of lighting shall provide uniform and consistent illumination throughout the compartment.

BODY ROOF
The body roof sheet shall be fabricated from NFPA compliant embossed non-skid .125” polished aluminum treadbrite. The roof sheet shall be supported with 3" channel to support the weight of several firefighters, and permanently mounted to insure a weatherproof seal.

The roof shall be a two piece roof assembly and be removable. The front section shall cover the tank, the rear portion shall cover the plumbing, pump, reel etc.

There shall be access for the fill towers, the pump engine exhaust shall protrude out the top of the rear roof assembly.

The roof shall be provided with provisions for air flow which will be required for the pump engine.

COMPARTMENT LAP DOORS
The compartment doors shall be double panel lap doors. The outside door panel shall be 3/16" (.1875) 3003 alloy smooth aluminum sheeting and the inner stiffener panel shall be 1/8" (.125) 3003 alloy smooth aluminum sheeting.

There shall be a heavy-duty, automotive type, extruded rubber molding installed around the doors to insure a weatherproof seal. Compartment doors shall have a polished stainless steel continuous hinge with a 1/4" diameter stainless steel pin and shall be fastened to the body with 1024 stainless steel bolts.

Door handles shall be 6" diameter stainless steel recessed "D" ring handles. There shall be a polymer film placed between the handle and door to insulate dissimilar metals and protect against galvanic corrosion. The "D" ring compartment latches shall be adjustable with a single point striker pin and double catch.

DRIP RAILS
Drip rails shall be provided above each door of the body.

Attachment 2
Council Agenda 9-1-2026 9.H-17

CITY OF PISMO BEACH FIRE DEPARTMENT

PISMO BEACH, CA
08/04/26 Page 8 of 34

VERTICALLY HINGED SWING-OUT DOORS
All vertically hinged swing-out compartment door(s) shall open from the rear of the body and be spring loaded to hold the door in an open position. The spring loaded door holder shall close the door automatically when the door is positioned over center.

HORIZONTALLY HINGED LIFT-UP DOORS
All horizontally hinged lift-up compartment door(s) shall be furnished with two (2), pressurized, gas filled pneumatic cylinders. There shall be one cylinder on each side of the door to assist in raising and holding the door in the open position. The lift-up door(s) shall swing-up high enough to allow for head clearance.

INNER DOOR PANELS, DA SANDED
All compartment inner door stiffener panels shall be DA sanded in order to create a smooth finish.

COMPARTMENT L1
There shall be a transverse compartment located behind the chassis cab with an approximate door opening of 27" wide x 52" high and a single, vertically hinged swing-out door.

The compartment door handle shall be locking. All locking compartment doors on the apparatus shall be keyed alike.

The compartment under the frame shall have a usable depth of approximately 20".

There shall be one (1) adjustable shelf(ves) located in the compartment. The shelf(ves) will be constructed of 3/16" smooth aluminum with a 2” lip at the front and rear of the shelf.

The shelf(ves) shall be mounted on strut channel to allow them to be adjusted in the compartment.

The shelf shall be center depth.

There shall be matting installed in the adjustable shelf to provide traction and drainage should water enter the compartment.

The shelf front shall be modified to match height of turtle tile (3/4") There shall be a heavy duty, roll out equipment tray installed in the compartment. The tray shall be constructed of 3/16" smooth aluminum with a 4" minimum perimeter and an abraded finish and will extend to the center of the apparatus.

The roller rail system shall be a SlideMaster model SM3-SP steel assembly with a rated distributed load capacity of 1,000 lbs and 100% extension capabilities.

COMPARTMENT L2
There shall be a compartment located above the rear chassis wheels with an approximate door opening of 50" wide x 29" high and a single, horizontally hinged lift-up door.

The compartment door handle shall be locking. All locking compartment doors on the apparatus shall be keyed alike.

The compartment shall have a usable depth of approximately 20".

A permanent aluminum divide shall be provided and mounted 30" rearward of the front bulkhead.

The two roll out trays shall be mounted in the area rearward of the permanent divide.

There shall be vertical struts located in the compartment for the future installation of shelves/trays.

There shall be two (2) roll out tray(s) located in the compartment that are adjustable. The roll-out tray shall be constructed of 3/16" smooth aluminum with a 3" lip around the perimeter of the tray. The tray shall be mounted with a pair of heavy-duty lock-in/lock-out slides with a full width Austin lift-up Front Drawer Release for convenient one handed operation.

The tray shall have a maximum capacity of 500 lbs.

There shall be matting installed in the roll-out tray to provide traction and drainage should water enter the compartment.

There shall be One (1) full height, slide out toolboard(s) provided and mounted in the compartment. The toolboard(s) shall consist of an abraded smooth aluminum sheet with a 90 degree bend on the front edge to provide strength and act as a handle. The aluminum toolboard(s) shall be mounted to heavy- duty lock-in/lock-out slides with a front trigger release.

The toolboard will be mounted 15" rearward of the front bulkhead.

Attachment 2
Council Agenda 9-1-2026 9.H-18

CITY OF PISMO BEACH FIRE DEPARTMENT

PISMO BEACH, CA
08/04/26 Page 10 of 34
There shall be floor matting installed in the compartment to provide traction and drainage should water enter the compartment.

This compartment door opening shall be supplied with two (2) lighting strips, located one on each side of the door opening running vertically.

COMPARTMENT L3
There shall be a compartment located behind the rear chassis wheels with an approximate door opening of 29" wide x 52" high and a single, vertically hinged swing-out door.

The compartment door handle shall be locking. All locking compartment doors on the apparatus shall be keyed alike.

The compartment shall have a usable depth of approximately 20".

There shall be two (2) adjustable shelf(ves) located in the compartment. The shelf(ves) will be constructed of 3/16" smooth aluminum with a 2” lip at the front and rear of the shelf.

The shelf(ves) shall be mounted on strut channel to allow them to be adjusted in the compartment.

The shelf front shall be modified to match height of turtle tile (3/4") There shall be matting installed in the adjustable shelf to provide traction and drainage should water enter the compartment.

There shall be one (1) roll out tray(s) located in the compartment. The roll-out tray shall be constructed of 3/16" smooth aluminum with a 3" lip around the perimeter of the tray. The tray shall be mounted with a pair of heavy-duty lock-in/lock-out slides with a full width Austin lift-up Front Drawer Release for convenient one handed operation.

The tray shall have a maximum capacity of 500 lbs.

There shall be matting installed in the roll-out tray to provide traction and drainage should water enter the compartment.

This compartment door opening shall be supplied with two (2) lighting strips, located one on each side of the door opening running vertically.

HOSE BED
There shall be a hose bed built integral above the left side compartments running the full length of the body. The hose bed shall be approximately 12" in height.

This area shall be equipped with drain holes to allow standing water to exit.

A hinged aluminum embossed treadbrite cover shall be supplied on the hose bed. The cover shall be fastened with stainless steel hinges to the outer-side of the body and equipped with a pressurized gas filled pneumatic cylinder to assist in raising and holding the cover in the open position.

A chrome grab handle shall be mounted on the cover to aid in opening and closing the cover.

A drop down hinged drop down door with latch made of smooth aluminum shall be provided at the rear of the hosebed. The drop down door shall have chevron striping provided.

There shall be matting in the hose bed area(s) to provide traction and drainage should water enter the area.

NOTE: Lighting will not be provided in this area and the door or cover (if applicable) will not be connected to the open door warning light.

COMPARTMENT R1
There shall be a transverse compartment located behind the chassis cab with an approximate door opening of 27" wide x 52" high and a single, vertically hinged swing-out door.

The compartment door handle shall be locking. All locking compartment doors on the apparatus shall be keyed alike.

The compartment area under the frame shall have a usable depth of approximately 20".

There shall be one (1) adjustable shelf(ves) located in the compartment. The shelf(ves) will be constructed of 3/16" smooth aluminum with a 2” lip at the front and rear of the shelf.

The shelf(ves) shall be mounted on strut channel to allow them to be adjusted in the compartment.

The shelf shall be center depth.

There shall be matting installed in the adjustable shelf to provide traction and drainage should water enter the compartment.

There shall be a heavy duty, roll out equipment tray installed in the compartment. The tray shall be constructed of 3/16" smooth aluminum with a 4" minimum perimeter and an abraded finish and will extend to the center of the apparatus.

Attachment 2
Council Agenda 9-1-2026 9.H-19

CITY OF PISMO BEACH FIRE DEPARTMENT

PISMO BEACH, CA
08/04/26 Page 12 of 34
The roller rail system shall be a SlideMaster model SM3-SP steel assembly with a rated distributed load capacity of 1,000 lbs and 100% extension capabilities.

The tray shall be provided with an IMS spring lock. The spring lock is operated with a round red knob, pulling on the knob releases the tray for outward travel and pushing on the knob releases for inward travel. The spring lock automatically locks the tray in the open and closed positions.

There shall be matting installed in the roll-out tray to provide traction and drainage should water enter the compartment.

There shall be floor matting installed in the compartment to provide traction and drainage should water enter the compartment.

This compartment door opening shall be supplied with two (2) lighting strips, located one on each side of the door opening running vertically.

COMPARTMENT R2
There shall be a compartment located above the rear chassis wheels with an approximate door opening of 50" wide x 29" high and a single, horizontally hinged lift-up door.

The compartment door handle shall be locking. All locking compartment doors on the apparatus shall be keyed alike.

The compartment shall have a usable depth of approximately 20".

There shall be one (1) adjustable shelf(ves) located in the compartment. The shelf(ves) will be constructed of 3/16" smooth aluminum with a 2” lip at the front and rear of the shelf.

The shelf(ves) shall be mounted on strut channel to allow them to be adjusted in the compartment.

There shall be matting installed in the adjustable shelf to provide traction and drainage should water enter the compartment.

There shall be floor matting installed in the compartment to provide traction and drainage should water enter the compartment.

This compartment door opening shall be supplied with two (2) lighting strips, located one on each side of the door opening running vertically.

COMPARTMENT R3
There shall be a compartment located behind the rear chassis wheels with an approximate door opening of 29" wide x 52" high and a single, vertically hinged swing-out door.

The compartment door handle shall be locking. All locking compartment doors on the apparatus shall be keyed alike.

The compartment shall have a usable depth of approximately 20".

There shall be one (1) adjustable shelf(ves) located in the compartment. The shelf(ves) will be constructed of 3/16" smooth aluminum with a 2” lip at the front and rear of the shelf.

The shelf(ves) shall be mounted on strut channel to allow them to be adjusted in the compartment. The strut channel shall be full height.

The shelf front shall be modified to match height of turtle tile (3/4") There shall be matting installed in the adjustable shelf to provide traction and drainage should water enter the compartment.

The tray shall have a maximum capacity of 500 lbs.

There shall be matting installed in the roll-out tray to provide traction and drainage should water enter the compartment.

This compartment door opening shall be supplied with two (2) lighting strips, located one on each side of the door opening running vertically.

Attachment 2
Council Agenda 9-1-2026 9.H-20

CITY OF PISMO BEACH FIRE DEPARTMENT

PISMO BEACH, CA
08/04/26 Page 14 of 34

DUNNAGE STORAGE
There shall be a dunnage storage area built integral above the right side compartments running the full length of the body. The dunnage area shall be approximately 12" in height and accessible from the top.

This area shall be equipped with drain holes to allow standing water to exit.

A hinged aluminum embossed treadbrite cover shall be supplied to enclose the dunnage storage area.

The cover shall be fastened with stainless steel hinges to the outer-side of the body and equipped with a pressurized gas filled pneumatic cylinder to assist in raising and holding the cover in the open position.

A chrome grab handle shall be mounted on the cover to aid in opening and closing the cover and an exterior hold-down latch will be provided to prevent the cover from accidentally opening in route to the scene.

There shall be matting in the dunnage storage area(s) to provide traction and drainage should water enter the area.

NOTE: Lighting will not be provided in this area and the door or cover (if applicable) will not be connected to the open door warning light.

REAR UNDER BED COMPARTMENT
There shall be an aluminum storage compartment located under a part of the cargo skid unit floor and accessible from the rear. This compartment shall be approximately 40" W x 12" H (useable) with a depth of 56" with a horizontally hinged drop down smooth aluminum door.

A locking D ring style latch shall be installed at center.

NOTE: Lighting will not be provided in this area.

STEPS
Steps shall be 8" die cast zinc/aluminum alloy folding type and to be mounted with stainless steel bolts.

The surface area shall be at least 35 square inches and withstand a load of at least 500 pounds.

Each folding step shall be provided with an upper and lower LED light to illuminate the stepping areas.

The integral step lighting shall be activated with the ground and surface lighting.

The steps shall be located in the follows areas:

Six (6) folding steps shall be mounted at the rear of the body, three per side.

HANDRAILS
Handrails shall be round extruded aluminum. The handrail brackets shall be brass, chrome plated and fastened to the body with stainless steel bolts. Each handrail shall include a RED LED light backlight.

The handrails shall be located in the following area(s):

Two (2) vertical handrails shall be mounted on the rear of the body, one each side. The handrail shall be approximately 12" in height.

One (1) horizontal handrail shall be mounted on the driver side at the top of the body.

One (1) horizontal handrail shall be mounted on the passenger side at the top of the body.

All handrails to be Hansen brand with lights and knurled finish and no rubber inserts. The lights shall be activated same as ground lights.

HOSE HOOKS
Two (2) Cast Products hose hangers shall be provided for the hose hook brackets, the hose hook brackets shall be mounted between the top and bottom steps, one on each side at the rear of the apparatus.

SCBA CYLINDER STORAGE LEFT SIDE WHEEL WELL
Two (2), single SCBA cylinder storage tubes shall be installed in the rear wheel well area on the driver's side of the body. The tube shall be an aluminum 8" diameter tube with a protective insert to prevent damage to the cylinder. There shall be a drain hole in the rear of the tube and a safety strap installed to secure the cylinder inside the tube.

Two (2), Cast Products hinged access doors shall be provided to enclose the cylinder storage tubes.

NOTE: The customer bottles are 23.5" in height, an extension shall be provided to ensure the bottle storage is adequate.

SCBA CYLINDER STORAGE RIGHT SIDE WHEEL WELL
Two (2), single SCBA cylinder storage tubes shall be installed in the rear wheel well area on the passenger's side of the body. The tube shall be an aluminum 8" diameter tube with a protective insert to prevent damage to the cylinder. There shall be a drain hole in the rear of the tube and a safety strap installed to secure the cylinder inside the tube.

Two (2), Cast Products hinged access doors shall be provided to enclose the cylinder storage tubes.

NOTE: The customer bottles are 23.5" in height, an extension shall be provided to ensure the bottle storage is adequate.

Attachment 2
Council Agenda 9-1-2026 9.H-21

CITY OF PISMO BEACH FIRE DEPARTMENT

PISMO BEACH, CA
08/04/26 Page 16 of 34
12-VOLT ELECTRICAL
All electrical equipment shall be installed using high temperature, copper, multi-strand, crosslink-coated wire. The wiring shall be colored coded and the function labeled every 3” end to end.

All wiring shall be enclosed in a protective loom throughout the electrical system and rubber grommets shall be used where the wiring passes through module walls.

All wire connections located under the apparatus body shall be weatherproofed with a clear, flexible, protective coating.

CAB CONSOLE
There shall be a custom built console installed in the chassis cab between the front bucket seats. The console shall have a standard layout designed by the manufacturer to accommodate light and siren controls, and other items specific to the apparatus.

The console shall be finished with a black, durable textured coating.

The top of the console shall be tilted up at the front side to allow for better visibility of the controls and help reduce sun glare.

There shall be One (1) open storage pocket(s) provided at the rear of the console. It shall be the same width as the console and extend approximately 2 1/2" from the rear of the console.

There shall be two (2) plastic cup holders provided in the cab console.

There shall be two (2) side mount armrests provided and installed on the cab console.

There shall be two momentary rocker switches located on the custom console.

Rocker switches to be Carling brand.

Customer to provide use and amp draw at pre-construction meeting.

There shall be one (1) Kussmaul USB Dual Port 091-264 installed in the cab console. The USB dual port has one 18 watt max USB-A port & one 45 watt max USB-C port.

It shall be wired to be hot at all times.

WHELEN CENCOM CONTROL SYSTEM
A Whelen CenCom Core system shall be installed on the apparatus. The CenCom Core system shall include a remote head mounted in the chassis cab console. The control head shall have 3 sections.

Section one shall house 8 push button switches. Section two shall house a 4-position slide switch, 7- position rotary knob and push buttons for manual & airhorn. Section three shall house three push buttons to control the traffic advisor (if equipped).

The CenCom Core shall be wired to control the siren and all warning lights, scene lights, and any other specified electrical devices.

APPARATUS BODY 12-VOLT DISCONNECT
One (1), disconnect solenoid with a sufficient amp rating shall be wired from the battery and activated by the chassis ignition to disconnect all electrical accessories added by the body manufacturer. Items such as auxiliary engine starter, winch, booster reel(s), or high amp load items shall be excluded from the disconnect solenoid.

One (1), reset breaker shall be installed between the solenoid output and any electrical load.

One (1), indicator light shall be provided to indicate the apparatus 12-volt system is on. The light shall be located in the chassis cab and be visible from the driver’s positions. The light shall be green in color and labeled "BATTERY ON".

DOOR OPEN WARNING LIGHT
A flashing red LED hazardous warning light shall be mounted in the chassis cab. This light shall indicate any open compartment doors, and/or other items permanently attached to the apparatus that may cause damage should the apparatus be moved.

The warning light shall be marked with a decal that states "DO NOT MOVE APPARATUS WHEN LIGHT IS ON".

Note: Doors without a light strip shall not be connected to the open door warning light.

RADIO CUTOUT AND POWER
Two (2), cutout(s) for a customer installed radio shall be provided on the cab console. There shall be mounting tabs located inside the console to allow for easy mounting of the radio by the customer.

Two (2), 12 volt spare circuit(s), with appropriate breakers and lead wires, shall be provided and routed to a location inside the cab console and tagged. The spare circuit shall be switched on and off with the ignition.

NOTE: Customer is required to provide radio brand and model at time of the pre-construction to ensure the correct cutout.

Attachment 2
Council Agenda 9-1-2026 9.H-22

CITY OF PISMO BEACH FIRE DEPARTMENT

PISMO BEACH, CA

08/04/26 Page 18 of 34

BRAKE/TURN/REVERSE LIGHTS
The apparatus shall be equipped with the following rear tail light package.

The brake/tail lights shall be Whelen M6 series model M6BTT lights. The lights shall have red LED's and a red lens. (top)

The turn arrow lights shall be Whelen M6 model M6T lights. The lights shall have amber LED's and an amber lens. (center)

The reverse lights shall be Whelen M6 model M6BUW lights. The lights shall have clear LED's and a clear lens. (lower)

The lights shall be housed in a Whelen M6FCV4 four (4) light vertical chrome plated housing.

The lower zone C warning lights shall be Whelen M6 model M6RC lights. The lights shall be installed at the bottom of the light flange. The lights shall have red LED's and a clear lens.

CLEARANCE MARKER LIGHTS
There shall be LED clearance marker lights provided to comply with ICC regulations. The clearance marker lights shall be located one on each side and rear corner of the apparatus body and a triple red light cluster recessed at the rear center of the body for a total of seven clearance marker lights.

Reflectors shall be supplied on the perimeter of the apparatus as specified by ICC regulations.

LICENSE PLATE BRACKET
A polished aluminum, LED lighted license plate bracket shall be mounted at the rear of the apparatus.

LED GROUND & SURFACE LIGHTING
LED ground and surface lighting shall be installed in areas where personnel may be expected to climb onto the apparatus and to illuminate all work surfaces, steps, and walkways. These areas shall include cab doors, and the rear step area.

The ground and surface lighting shall be activated when the transmission is in park.

An additional switch shall be provided in the cab to activate or deactivate the ground and surface lighting at any time.

SIREN
The siren shall be built-in as part of the Whelen CenCom system and controlled with the CenCom controller.

SPEAKER
Two (2), Cast Products compact speakers, model SA4201-6B, 100 watt speaker shall be mounted on the apparatus.

UPPER ZONE A LIGHTING
One (1), Whelen Liberty ll customer 54" LED lightbar shall be installed on the apparatus. The lightbar shall be configured as per diagram.

All white forward facing emergency lights in the light bar shall be deactivated when the parking brake is engaged in the Blocking Right of Way mode as required by NFPA.

The lightbar shall be mounted on top of the chassis cab roof.

Two (2) red to meet California steady burn as per lightbar layout.

Functions of lightbar.

1. All whites turn off in front when in park and when you press takedown button.

2. When in park, the alternating white flashing lights at front of lightbar turn off.

UPPER ZONE B/ZONE D LIGHTING
The following perimeter lighting shall be installed in the upper B and D zones of the apparatus.

One (1) Whelen M6RC LED light shall be installed on the front passenger's side of the apparatus.

The light shall have red LEDs and a clear lens cover with a chrome flange.

One (1) Whelen M6RC LED light shall be installed on the rear passenger's side of the apparatus. The light shall have red LEDs and a clear lens cover with a chrome flange.

One (1) Whelen M6RC LED light shall be installed on the front driver's side of the apparatus. The light shall have red LEDs and a clear lens cover with a chrome flange.

One (1) Whelen M6RC LED light shall be installed on the rear driver's side of the apparatus. The light shall have red LEDs and a clear lens cover with a chrome flange.

Attachment 2
Council Agenda 9-1-2026 9.H-23

CITY OF PISMO BEACH FIRE DEPARTMENT

PISMO BEACH, CA
08/04/26 Page 20 of 34

UPPER ZONE C LIGHTING
Two (2) Whelen M6RC series linear super-LED light shall be installed on the outer rear corners of the apparatus, one per side. The lighthead shall have red LEDs and a clear lens cover. The light shall be housed in a chrome flange.

LOWER ZONE A LIGHTING
Two (2), Whelen M2WRC LED lights shall be installed at the front of the apparatus, one on each side with a chrome flange. The light shall have red LEDs and a clear lens.

LOWER ZONE B/ZONE D LIGHTING
The following perimeter lighting shall be installed in the lower B and D zones of the apparatus.

One (1) Whelen M2WRC LED light shall be installed on the front passenger's side of the apparatus.

The light shall have red LEDs and a clear lens cover with a chrome flange.

One (1) Whelen M2WRC LED light shall be installed on the rear passenger's side of the apparatus.

The lighthead shall have red LEDs and a clear lens cover with a chrome flange.

One (1) Whelen M2WRC LED light shall be installed on the front driver's side of the apparatus. The light shall have red LEDs and a clear lens cover with a chrome flange.

One (1) Whelen M2WRC LED light shall be installed on the rear driver's side of the apparatus. The light shall have red LEDs and a clear lens cover with a chrome flange.

LOWER ZONE C LIGHTING
The lower zone C lighting is included in the brake/turn/reverse lighting package which includes a quad flange.

TRAFFIC ADVISOR
There shall be six (6), Whelen model ION T-Series amber LED lights provided and installed at the rear of the apparatus. The six lights shall be programmed and operated through the Whelen Cencom system to create a traffic advisor. Operator can control left to right, split and right to left.

OEM BACKUP CAMERA
There shall be an OEM backup camera supplied with the chassis by the chassis manufacturer. The camera shall be mounted at the rear of the apparatus with the monitor located in the chassis cab. 12 VOLT FUSE BLOCK
There shall be (3) 12 volt fuse blocks with 6 circuits installed on the apparatus and wired to be hot at all times. The fuse block accepts ATO and ATC blade fuses and has a maximum amperage of 100A total and 30A per circuit. The cover for the fuse block incorporates storage for 2 spare fuses and labels are included to identify circuits.

For all blocks, wire side A to battery direct and side B with key switched for battery power.

The fuse block shall be installed in the following location:

One (1), Inside the chassis cab console
One (1), L1 front bulkhead as high as possible
One (1), R1 front bulkhead as high as possible
There shall be (3) each of the following fuses included. 5A, 10A, 15A, 20A, 25A, 30A (Blue Sea ST Blade Bus Part #5032)

SCENE LIGHTS
Whelen 600EZ series gradient LED scene lights with chrome flanges featuring inner optics to direct the light downward shall be provided and mounted at the following locations:

Two (2) Whelen 600EZ LED Scene lights shall be mounted on the left upper side of the apparatus body.

The left side scene lights shall be activated by a switch located in the chassis cab. The switch shall be labeled "LEFT SCENE LIGHTS.”
Two (2) Whelen 600EZ LED Scene lights shall be mounted on the right upper side of the apparatus body.

The right side scene lights shall be activated by a switch located in the chassis cab. The switch shall be labeled "RIGHT SCENE LIGHTS.”
Two (2) Whelen 600EZ LED Scene lights shall be mounted at the rear of the apparatus, one per side.

The rear scene lights shall be activated by a switch (Cencom) located in the chassis cab. The switch shall be labeled "REAR SCENE LIGHTS.”
There shall also be a weather proof switch at the rear to operate the rear scene lights.

The rear scene lights shall be activated when the chassis is placed in the reverse mode.

Attachment 2
Council Agenda 9-1-2026 9.H-24

CITY OF PISMO BEACH FIRE DEPARTMENT

PISMO BEACH, CA
08/04/26 Page 22 of 34

TELESCOPIC LIGHT
Two (2), Whelen Pioneer Plus model #PCH2P LED flood/spot light assembly shall be supplied. The assembly shall incorporate a dual LED flood/spot light with a white powder coated die-cast aluminum housing. The Pioneer flood light shall have 18,520 lumens.

The lighthead(s) shall be mounted to a Fire Research side mount push up telescopic pole. The pole shall be anodized aluminum and have a knurled twist lock mechanism to secure the extension pole in position. The extension pole shall be capable of rotating 360 degrees.

The light(s) shall be controlled with switches mounted inside the chassis cab.

The light(s) shall be located on the front of the apparatus body, one on each side and wired directly to the 12-volt electrical system.

PAINTING
After the apparatus body and components have been fabricated and assembled, the apparatus body shall be completely sanded and deburred for removal of sharp edges. The apparatus and components shall be metal prepped to provide a superior substrate for painting.

The apparatus body and components shall undergo a degreasing/cleaning process, starting with a clear, acidic liquid, designed to remove surface soils and oxidation. This process develops a light phosphate coating, which gives aluminum a superior base for good paint adhesion.

The apparatus body shall be painted to match the OEM chassis paint color:

After the cleaning process, a fast build epoxy primer shall be applied and sanded prior to the top finish coatings. The finish painting process shall consist of applying two (2), coats of high quality, 3.5 VOC polyurethane paint to maintain proper film thickness.

COMPARTMENT INTERIOR PAINT
All compartment interiors shall be painted with a multicolor textured paint. The color shall be "Marblestone" a white and grey finish.

The finish offers exceptional durability for use in apparatus compartments providing a scuff and chemical resistant finish.

ELECTROLYSIS CORROSION CONTROL
The apparatus shall be assembled using ECK or electrolysis corrosion control, on all high corrosion potential areas, such as door latches, door hinges, trim plates, fenderettes, etc. This coating is a high zinc compound that shall act as a sacrificial barrier to prevent electrolysis and corrosion between dissimilar metals. This shall be in addition to any other barrier material that may be used.

All ¼” diameter and smaller screws and bolts shall be stainless steel with a powdered aluminum coating. This coating shall be bonded metallurgically to the stainless screws to prevent peeling and flaking. This coating is designed to reduce the potential for electrolysis and corrosion to occur where items are assembled and attached.

BODY UNDERCOATING
The entire underside of the body shall be coated with a tough, pliable, rubberized coating for protection against abrasion and corrosion. This hybrid undercoating features a water based formula with quick dry capability to achieve early water and weather resistance.

The undercoating shall be applied prior to installation of the body onto the chassis to avoid spraying the product on air lines, cables, or other items that would cause normal maintenance to be hindered.

LETTERING
The lettering shall be provided and installed.

1. PISMO BEACH arched on both front doors (Gold Shadowed)

2. FIRE DEPT. straight in line with stripe on front doors (Gold Shadowed)

3. Truck Number Straight on rear doors. (Gold Shadowed)

4. The door badges will be supplied by the FD.

WHITE REFLECTIVE STRIPING
Reflective striping shall be applied to the exterior of the apparatus in a manner consistent with NFPA. A reflective stripe shall also be applied to the interior of each chassis cab door and body door as well as any equipment such as roll-out trays or frames that protrude beyond the body of the apparatus to indicate a hazard or obstruction. An additional reflective stripe shall be applied to the body's rub rails.

The color of the striping shall be WHITE.

The striping shall be 4" wide and applied to the chassis and body in a straight pattern.

There shall be a 1/4" black reflective stripe applied above and below the center white stripe.There shall be a 3/4" gold stripe above and below the 1/4" black reflective stripe. There shall be a 1/4" black reflective stripe above and below the gold stripe.

Attachment 2
Council Agenda 9-1-2026 9.H-25

CITY OF PISMO BEACH FIRE DEPARTMENT

PISMO BEACH, CA

08/04/26 Page 24 of 34

REAR CHEVRON REFLECTIVE STRIPING - RED/YELLOW
There shall be retro-reflective striping applied in a chevron pattern to the rear facing vertical surfaces of the apparatus.

The striping shall consist of alternating red and fluorescent yellow retro-reflective stripes. Each stripe shall be 6" in width and shall be applied to the apparatus at a 45° angle sloping downward and away from the centerline of the apparatus.

BODY STRUCTURE LIMITED WARRANTY
Danko Emergency Equipment Company shall warrant the body structure of the apparatus to be free of defects in design and workmanship for a period of seven (7) years.

ELECTRICAL WARRANTY
Danko Emergency Equipment Company shall warrant to each original purchaser that the Danko supplied electrical equipment are sound and free of all defects of both materials and workmanship, for a period of two (2) years. The warranty shall ensure that the vehicle will be free from defects in the electrical harness and connections under normal use and service within the warranty period.

PAINTED METAL SURFACE WARRANTY
Danko Emergency Equipment Company shall warrant the completed apparatus to be free of blistering, peeling and any other adhesion defect caused by defective manufacturing methods or paint material selection for metal exterior surfaces for a period of seven (7) years.

BASIC LIMITED WARRANTY
Danko Emergency Equipment Company shall warrant to each original purchaser that the apparatus is free of defects in material and workmanship for a period of one (1) year.

LETTERING/STRIPING WARRANTY
Danko Emergency Equipment Company shall warrant to each original purchaser that the apparatus lettering and/or striping shall be free of defects for a period of three (3) years.

MANUALS/DOCUMENTATION
There shall be one (1) 3-ring binder and one (1) electronic copy of the manufacturer operation and maintenance manual provided that covers the completed apparatus.

An additional electronic copy shall be provided inside the chassis in compliance with NFPA 1900.

The manuals shall include chassis documentation, wiring diagrams, and any other documents or technical data referencing the apparatus. Also included shall be any manufacturers warranties and/or guarantees.

DANKO SKID UNIT
UPF Defender Poly Tank

FACTORY INSTALLED SKID UNIT
The skid unit shall be mounted on the above specified fire apparatus and connected to the 12-volt electrical system.

OPERATOR PUMP PANEL
The rear cargo area shall be enclosed with a pump operators panel. The panel shall be constructed of 3/16" aluminum and covered with a black durable finish.

The panel shall be attached to the body on the left and right side, the bottom of the panel shall be attached to the cargo floor. The top of the panel shall terminate at the rear body roof panel.

The panel shall contain instruments, gauges, and optional controls.

The operators panel shall be illuminated with LED lighting and activated when the pump engine starts.

The panel shall be appropriately labeled at all instruments and controls.

The panel shall be provided with slots to provide air flow for the pump engine. A fan with thermostat shall be provided.

PUMP ENGINE RUNNING LIGHT
A green LED light shall be mounted in the chassis cab. This light shall turn on and off with the pump engine ignition to notify the operator when the pump engine is running.

The light shall be labeled "PUMP ENGINE RUNNING".

FIRE PUMP
A Waterous 2515LE pump shall be provided and bolted directly to the specified engine.

The impeller shall be high strength corrosion resistant bronze, fully enclosed, double hubbed to balance hydraulic thrust, and mechanically balanced to eliminate vibration. The volute shall be constructed of high strength aluminum alloy, anodized for superior corrosion resistance. A drain valve shall be located on bottom of the pump volute.

The pump shall have a two (2) year warranty covering material and workmanship. Normal wear items (packing, anodes, mechanical seals, etc.) are not covered by this warranty.

The pump shall be firmly mounted to the skid frame or platform behind the water tank.

Attachment 2
Council Agenda 9-1-2026 9.H-26

CITY OF PISMO BEACH FIRE DEPARTMENT

PISMO BEACH, CA
08/04/26 Page 26 of 34
NOTE: The above performance rating is based on full throttle with a flooded suction and discharge plumbing installed.

PUMP ENGINE
A Kubota D902-E4B vertical 4-cycle water cooled 24.8 HP 3 cylinder diesel engine shall be supplied and mounted to the pump. The engine features easy one-sided maintenance, an automotive style oil filter and oil fill tube with dipstick, heavy duty copper radiator, and a heavy duty air cleaner.

There shall be a rain cap installed on top of the exhaust.

Displacement- 0.898 L (54.8 cu in); Bore x Stroke- 72.0 x 73.6 mm; Output- 24.8 HP @ 3,600 rpm; Torque- 41.4 lbs ft @ 2,600 rpm

PUMP ENGINE START CONTROL MODULE
A Deep Sea DSE3110 manual and auto start control module shall be provided and mounted near the pump engine.

The Deep Sea control module has been designed to provide advanced engine monitoring and protection features. The back-lit icon LCD display provides information to the operator regarding engine speed, frequency, voltage, and engine run hours via simple one button navigation. The Deep Sea also features an engine pre-heat setting which warms the engine to a safe temperature at start-up to increase engine life, a remote start input, and shutdown warning protection for multiple fault conditions.

The Deep Sea is IP65 rated for weather resistance.

PUMP ENGINE THROTTLE
The pump engine shall be supplied with a vernier style throttle mounted near the pump operators position. The operation of the remote throttle shall consist of seven full turns from idle to wide open engine speed. The throttle shall have a red center button to quickly return the engine to idle when depressed.

LED PUMP PANEL LIGHT
The rear pump operator's control panel shall be illuminated with a LED light and a shield shall be installed over the light to protect it from the elements. A properly labeled on/off switch shall be supplied and mounted on the rear operators panel.

The rear panel light shall be activated when the pump engine starts.

DISCHARGE PRESSURE GAUGE
There shall be one (1), discharge pressure gauge installed on the rear operators panel. The gauge shall be a minimum of 2-1/2" in diameter with a white face and black text.

IN CAB PUMP ENGINE START
The pump engine shall have a remote start/stop toggle switch provided and mounted in the chassis cab with a red safety guard.

REMOTE VERNIER THROTTLE CONTROL
The apparatus shall be equipped with an additional vernier style remote throttle control located in the chassis cab. The operation of the remote throttle shall consist of seven full turns from idle to wide open engine speed. The throttle shall have a red center button to quickly return the engine to idle when depressed.

DISCHARGE PRESSURE GAUGE
There shall be one (1), discharge pressure gauge installed in the chassis cab in clear view of the operator. The gauge shall be a minimum of 2-1/2" in diameter with a white face and black text.

PUMP ENGINE OIL DRAIN
An engine oil drain valve shall be provided and installed on the engine. The oil drain valve shall have a nipple to accept 3/8" ID hose to allow draining of the engine oil.

An extension hose shall be provided and terminate under the body.

COMMON FUEL SYSTEM
The pump engine shall be connected directly to the chassis fuel tank with a separate siphon tube and an electric fuel pump so that the pump engine and chassis share the same fuel source.

ENGINE COOLER
There shall be a pump engine cooler installed on the Kubota engine. The cooling system uses water from the discharge side of the pump to cool the engine coolant through the use of a closed heat exchanger. The water from the pump and the engine coolant shall not be intermixed.

OILLESS PRIMER
A Waterous VPOS electric motor driven rotatory vane primer shall be utilized. The primer allows repriming while pumping without reducing engine RPM. All rotating parts are made of corrosion resistant, anodized aluminum, stainless steel and composite materials.

A vacuum activated priming valve shall be supplied to control the primer. The VAP opens automatically during pump priming and closes automatically when the primer is deactivated. The primer switch shall be mounted near the pump.

Attachment 2
Council Agenda 9-1-2026 9.H-27

CITY OF PISMO BEACH FIRE DEPARTMENT

PISMO BEACH, CA
08/04/26 Page 28 of 34

APPARATUS PUMP SYSTEM CERTIFICATION
The pump shall be tested and certified by the apparatus manufacturer after the pump and all its associated piping and equipment have been installed on the fire apparatus.

The testing shall comply with NFPA 1900 section 15.13 Apparatus Pump System Certification and shall be certified by the apparatus manufacturer. Test results shall be provided to the end user at the time of delivery.

A test label shall be provided to indicate the rated discharges and pressures together with the speed of the engine as determined by the certification test and attached to the vehicle prior to delivery.

MASTER DRAIN VALVE
A manual master pump drain valve shall be installed and located on the rear operators control panel.

INDIVIDUAL DRAINS
Four (4) drains with lift up type handles shall be provided for the discharges. The drain controls shall be located at the rear of the apparatus.

PUMP COOLER LINE
There shall be a Class 1 3/8" pump cooling/recirculating line connected from the discharge side of the pump directly into the water tank. The cooler line shall be controlled with a valve on the operators panel, and it shall be clearly labeled.

PUMP COOLER CHECK VALVE
There shall be a check valve installed in the pump cooler line to prevent tank water from back flowing into the pump when it is not in use.

CUSTOM PLUMBING
Plumbing shall be a combination of heavy duty stainless steel pipe and fittings, and high pressure rubber hose.

The high pressure rubber hose is designed to handle air, mild chemicals and water and is resistant to abrasion and UV protected.

The stainless steel pipe and fittings shall have a polished natural mill finish.

A vertical manifold shall be attached to the discharge side of the pump to facilitate all outlets and reduce friction loss. The manifold shall be constructed of stainless steel tubing.

VALVES
All valves, unless otherwise specified, shall be an Akron 8800 heavy duty brass, quarter-turn, full flow, swing out, non-locking valve with a stainless steel ball. The valve body is constructed of high quality brass.

All valves shall be labeled to indicate function.

All Akron 8800 series valves shall be supplied with a TSC handle with a round knob attached.

TANK TO PUMP
The tank to pump shall be equipped with a 2" Akron 8820 full flow, quarter turn ball, swing-out type valve with a flexible hose to reduce vibration of the pump engine.

The valve shall be labeled and controlled at the rear operators panel.

The valve shall be in the open position when pushed IN and shall be closed when in the OUT position.

PUMP TO TANK/RECIRCULATE VALVE
One (1) 1" tank fill/recirculate line with a 1" Akron 8810 full flow, quarter turn ball valve shall be plumbed directly from the pump discharge to tank with a flexible hose to reduce vibration of the pump engine.

The valve with a push/pull handle shall labeled and operated from the rear operators panel.

GATED INTAKE
One (1), 2-1/2" female intake shall be mounted to the pump inlet and controlled with a 2-1/2” Akron 8825 full flow, quarter turn ball valve. The intake shall terminate with a chrome 2-1/2" NPT female x 2- 1/2" NH female swivel fitting with a screen to prevent foreign objects from entering the pump.

A drain shall be provided on the intake valve.

The rear intake shall be controlled at the rear operators panel, the intake shall be labeled.

PLUG WITH CHAIN
One (1), 2-1/2” NH chrome plug with chain shall be supplied for the intake. 1 1/2" PRECONNECT DISCHARGE
There shall be One (1), 1-1/2" NH preconnect with a 1-1/2" Akron 8815 full flow, quarter-turn ball valve. The preconnect shall be located inside of the left side preconnect hose bed and terminate with a 90° stationary elbow directed towards the rear.

The valve shall be labeled and controlled at the rear operators panel.

Attachment 2
Council Agenda 9-1-2026 9.H-28

CITY OF PISMO BEACH FIRE DEPARTMENT

PISMO BEACH, CA

08/04/26 Page 30 of 34

1-1/2” DISCHARGE
One (1) 1-1/2" NH discharge shall be provided with a 1-1/2” Akron 8815 full flow, quarter-turn valve.

The discharge shall terminate with a chrome 1-1/2” NPT male x 1-1/2” NH male fitting and be directed to the rear.

The valve shall be labeled and controlled at the rear operators panel.

CAP WITH CHAIN
One (1), 1-1/2" NH vented chrome cap with chain shall be supplied for the discharge.

FRONT DISCHARGE
One (1), 1-1/2" NH discharge shall be provided with a 1-1/2” Akron 8815 full flow, quarter-turn valve located at the rear manifold. The discharge shall terminate with a chrome 1-1/2” NPT male x 1-1/2” NH male fitting. The discharge shall terminate at the front of the apparatus towards the drivers side of the apparatus.

The valve shall be labeled and controlled at the rear operators panel.

CAP WITH CHAIN
One (1), 1-1/2" NH vented chrome cap with chain shall be supplied for the discharge.

AUTOMATIC DRAIN VALVES
There shall be Class 1 automatic drain valves installed in the lower sections of the front discharge plumbing.The automatic drain valves shall open whenever the pressure in the line drops below 6 PSI.

BOOSTER REEL
One (1), Hannay model EF16.5-30-31 steel electric booster reel, with a capacity of 150' of 1" booster hose shall be supplied. The reel shall be painted graphite in color. The reel shall have a 1" Akron 8810 full flow, quarter turn valve piped from the pump discharge and connected to the booster reel with a flexible hose to reduce vibration from the pump engine.

An auxiliary manual rewind crank shall be supplied with the reel and permanently mounted.

The valve shall be labeled and controlled at the rear operators panel.

One (1), set of enclosed rollers shall be mounted on the rear operators panel. The rollers shall provide assistance in pulling the hose off from the reel and guiding it on after use.

One (1), booster reel rewind switch shall be supplied and mounted on the rear operators panel.

NOZZLE/HOSE BRACKET
One (1), PAC model 1004-2 Handlelok, with a grip range from 1/8" to 1-3/4" and instant release capabilities shall be provided to securely mount the hose and/or nozzle.

The PAC Handlelok shall be mounted below the booster reel rollers on the rear operators panel.

WATER TANK
The water tank shall be a custom built poly tank with a capacity of 200 US gallons.

The tank shall have a LIFETIME WARRANTY as supplied by the tank manufacturer.

The tank shall be manufactured by United Plastics Fabricating Inc. and constructed of black 1/2" thick polypropylene resin. The material shall be of a certified, virgin, high quality, noncorrosive, stress relieved thermo plastic.

All joints and seams shall be fusion welded and electronically and hydrostatically tested for maximum strength. The unit shall incorporate interlocking transverse and longitudinal baffles manufactured of polypropylene completely welded to each other as well as to the inside of the tank.

The exterior of the tank shall be textured poly.

There shall be a minimum of two (2) standard tank connections: one for the tank-to-pump suction line, which shall be sized to provide adequate water flow to the pump; and, one for tank fill line, which shall be sized according to the NFPA minimum size chart for water tanks.

FILL TOWER
The tank shall be equipped with a combination vent/overflow and manual fill tower. The fill tower shall be rectanguler with lift up lid. The cover shall be fastened to the tower.

BOTTOM TANK OVERFLOW
There shall be a vent/overflow installed inside of the fill tower. The vent overflow shall be a polypropylene pipe with a minimum I.D. of 3" that is designed to run through and out the bottom of the tank. The overflow shall be directed to discharge water below the body.

Attachment 2
Council Agenda 9-1-2026 9.H-29

CITY OF PISMO BEACH FIRE DEPARTMENT

PISMO BEACH, CA
08/04/26 Page 32 of 34

INTERNAL SUMP
There shall be an internal sump in the tank. The sump shall be the same depth as the tank floor and shall have an anti-swirl plate located above the suction.

TANK DRAIN
There shall be a 1" FNPT female tank drain located under the tank with a 1" stainless steel plug accessible from under the body.

TANK COVER MOUNTING BLOCKS
The water tank cover shall incorporate two (2) mounting blocks that can accommodate sliding nut fasteners. These mounting blocks shall be welded to the tank cover and used to mount a booster reel or other equipment if selected.

WATER LEVEL GAUGE
The apparatus shall be equipped with one (1) Fire Research Tankvision LED electronic water level gauge. This level gauge utilizes ultra bright LEDs for sunlight readability and two wide-viewing lens for 180 degrees of clear viewing.

The water level gauge shall be located at the rear operators panel.

There shall be one (1) Fire Research cab miniature TANKVISION LED electronic water level display located inside the chassis cab.

FOAMPRO 1601 FOAM PROPORTIONING SYSTEM
The apparatus shall be equipped with an electronic, fully automatic, variable speed, direct injection, and discharge side FoamPro model 1601 foam proportioning system. A full flow check valve shall be provided in the discharge piping to prevent foam contamination of fire pump and water tank.

A simulated flow feature shall be incorporated into the motor driver to simulate an approximate flow value of 100 gpm. This feature is to be engaged or disengaged with a momentary switch and will automatically disengage when the main system switch is turned off.

A 12-volt electric motor driven positive displacement plunger pump shall be provided that has the capacity to pump from 0.1 gpm (0.38 L/min) to 1.0 gpm (3.8 L/min) at 200 psi (13.8 BAR) with a maximum operating pressure up to 400 psi (27.6 BAR). The system has a simulated flow feature incorporated into the motor driver to simulate an approximate flow value of 100 gpm.

Foam Concentration
1601 Maximum Water Flow
GPM (L/min)

FOAM CELL
One (1), twelve (12) gallon foam cell shall be constructed an integral part of the polypropylene water tank. The foam cell can be used for either Class A or Class B foam and shall be completely resistant to any reaction caused by the foam or any additives that may be used under normal circumstances. The seams shall be nitrogen welded and spark tested for maximum strength. The foam tank shall have a manual fill tower with lid.

The tower shall be located as indicated by the apparatus manufacturer and have a 1/4" thick removable polypropylene screen and a molded cover.

A pressure vacuum vent shall be provided in the lid of the fill tower.

FOAM CELL CLASSIFICATION
The foam cell shall be labeled for Class A foam.

SHUT OFF VALVE
A 1/2" shut-off valve shall be installed between the foam cell and the foam system for ease of maintenance.

FOAM LEVEL GAUGE
There shall be one (1) Fire Research Standard Tankvision LED electronic foam level gauge supplied with the apparatus. This level gauge utilizes ultra bright LEDs for sunlight readability. and two wide- viewing lens for 180 degrees of clear viewing. The foam level gauge shall be located on the rear operators panel.

There shall be one (1) Fire Research cab miniature TANKVISION LED electronic foam level slave display located inside the chassis cab.

Attachment 2
Council Agenda 9-1-2026 9.H-30

CITY OF PISMO BEACH FIRE DEPARTMENT

PISMO BEACH, CA

08/04/26 Page 34 of 34

POLY WATER TANK MOUNTING
The polypropylene water tank shall be an under mount design.

ALUMINUM PUMP FRAME
An aluminum frame shall be constructed with square aluminum tubing and angle supports. The frame will provide a secure means of mounting the fire pump to the apparatus deck.

12-VOLT ELECTRICAL
All electrical components of the unit shall be wired to two terminal stud blocks (hot/ground) with high temperature, copper, multi-strand, crosslink-coated wire enclosed in a protective loom.

The terminal stud blocks shall provide a single location to connect wiring from the chassis to provide power to all electrical components on the skid unit.

WORK LIGHT
One (1), 12-Volt LED work light shall be mounted on the back side of the rear operators control panel to light up the work area. An ON/OFF switch shall be located at the rear outside area of the rear operators panel.

BASIC LIMITED WARRANTY
Danko Emergency Equipment Company shall warrant to each original purchaser that the apparatus is free of defects in material and workmanship for a period of one (1) year.

STAINLESS STEEL PLUMBING WARRANTY
Danko Emergency Equipment Company shall warrant to each original purchaser that the apparatus stainless steel plumbing shall be free of defects for a period of ten (10) years.

EQUIPMENT

WHEEL CHOCKS
One (1), pair of Zico AC-1 aluminum wheel chocks with QCH-1 horizontal holders shall be supplied and mounted rearward of chassis rear wheels under body.

SALES DRAWING
Attachment 2
Council Agenda 9-1-2026 9.H-31

SALES DRAWING
Attachment 2
Council Agenda 9-1-2026 9.H-32

&RQWUDFW
1R
)6'DWH
3UHSDUHG

%X\LQJ
$JHQF\
&RQWUDFWRU

&RQWDFW
3HUVRQ

3UHSDUHG
%\

3KRQH
3KRQH

)D[
)D[

(PDLO
(PDLO

3URGXFW
'HVFULSWLRQ $4XLFN5HVSRQVH

&RVW &RVW

6XEWRWDO%

&RVW &RVW

6XEWRWDO&

6XEWRWDO'

6XEWRWDO(

&RVW &RVW

6XEWRWDO)

'HOLYHU\'DWH
*7RWDO3XUFKDVH3ULFH
'()

)7UDGH,QV6SHFLDO'LVFRXQWV2WKHU$OORZDQFHV)UHLJKW,QVWDOODWLRQ0LVFHOODQHRXV&KDUJHV 'HVFULSWLRQ 'HVFULSWLRQ
&DOLIRUQLDVDOHVWD[
(+*$&2UGHU3URFHVVLQJ&KDUJH
$PRXQW3HU&XUUHQW3ROLF\

&RPSDUWPHQW&XVWRPL]DWLRQV 3XPSDQG7DQN
(TXLSPHQW 6XEWRWDO)URP$GGLWLRQDO6KHHW
V

&KHFN
7RWDOFRVWRI&XVWRPL]DWLRQ&DWHJRULHV
&
FDQQRWH[FHHGRIWKHWRWDORIWKH%DVH
8QLW3ULFHSOXV3XEOLVKHG2SWLRQV
$%
)RUWKLVWUDQVDFWLRQWKHSHUFHQWDJHLV

'7RWDO&RVW%HIRUH$Q\$SSOLFDEOH7UDGH,Q2WKHU$OORZDQFHV'LVFRXQWV $%&

4XDQWLW\2UGHUHG
;6XEWRWDORI$%&

'HVFULSWLRQ 'HVFULSWLRQ
(5HPRWH(QJLQH&RQWUROV (;9DOYH&RQWUROVRQ3DQHO (9%RRVWHU5HHO5HFHVVHGLQ%RG\37HOHVFRSLQJ3ROH/LJKW [

3%DFN8S&DPHUD 6XEWRWDO)URP$GGLWLRQDO6KHHW V

37UDIILF$GYLVRUDW5HDURI$SSDUDWXV
&&XVWRPL]DWLRQ&DWHJRU\7RWDOV,WHPL]HEHORZ$WWDFKDGGLWLRQDOVKHHW V
LIQHFHVVDU\

1RWH
&XVWRPL]DWLRQRSWLRQVDUHPDQXIDFWXUHUQRQVWDQGDUGRSWLRQVZKLFKZHUHVXEPLWWHGDQGSULFHGLQ&RQWUDFWRUV VSURSRVDO

(
(OHFWULF3ULPHU *&XVWRP0DQLIROG
.
&XVWRP7DQN +)RDP3UR)RDP6\VWHP
*%RRVWHU5HHO (<(QFORVHG3XPS$UHD
:)URQW%XPSHU5HSODFHPHQW :3HUPDQHQW:LQFK '&&XVWRP%RG\&RQILJXUDWLRQ '
'XDO'LUHFWLRQDO5ROO2XW7UD\DQG0DWWLQJ
36WDQGDUG/LJKW3DFNDJHWR/DUJHU0RGHO/LJKWV (.XERWD+3GLHVHOHQJLQH &'LHVHOHQJLQHZLWKFKDVVLV :&UHZ&DE&KDVVLV
GNQREEH#GDQNRQHW
)RUGGUJDVFKDVVLV[)XOODOXPLQXPSDLQWHGERG\JDOORQZDWHU+3%ULJJVHQJLQH $3URGXFW,WHP%DVH8QLW3ULFH3HU&RQWUDFWRU
V+*$&&RQWUDFW

%3XEOLVKHG2SWLRQV,WHPL]HEHORZ$WWDFKDGGLWLRQDOVKHHW V
LIQHFHVVDU\

1RWH
3XEOLVKHG2SWLRQVDUHPDQXIDFWXUHUVWDQGDUGRSWLRQVZKLFKZHUHVXEPLWWHGDQGSULFHGLQ&RQWUDFWRU VSURSRVDO

'HVFULSWLRQ 'HVFULSWLRQ
&2175$&735,&,1*:25.6+((7
)RU027259(+,&/(62QO\
'XHWRJOREDOVXSSO\FKDLQFRQVWUDLQWVDQ\GHOLYHU\GDWHFRQWDLQHGKHUHLQLVDJRRGIDLWKHVWLPDWHDVRIWKHGDWHRIWKLV RUGHUFRQWUDFW$VQHHGHGGHOLYHU\XSGDWHVZLOOEHSURYLGHGDVVRRQDVSRVVLEOH &LW\RI3LVPR%HDFK 'DQNR(PHUJHQF\(TXLSPHQW&R
3DXO3URYHQFH 'DYLG.QREEH
Attachment 3
Council Agenda 9-1-2026 9.H-33

&RQWUDFW
1R
)6'DWH
3UHSDUHG

%X\LQJ
$JHQF\
&RQWUDFWRU

&RQWDFW
3HUVRQ

3UHSDUHG
%\

3KRQH
3KRQH

)D[
)D[

(PDLO
(PDLO

3URGXFW
'HVFULSWLRQ $4XLFN5HVSRQVH
&RVW &RVW

6XEWRWDO%

&RVW &RVW
6XEWRWDO&

6XEWRWDO'

6XEWRWDO(

&RVW &RVW
6XEWRWDO)

'HOLYHU\'DWH
*7RWDO3XUFKDVH3ULFH
'()

)7UDGH,QV6SHFLDO'LVFRXQWV2WKHU$OORZDQFHV)UHLJKW,QVWDOODWLRQ0LVFHOODQHRXV&KDUJHV 'HVFULSWLRQ 'HVFULSWLRQ
(+*$&2UGHU3URFHVVLQJ&KDUJH
$PRXQW3HU&XUUHQW3ROLF\

6XEWRWDO)URP$GGLWLRQDO6KHHW
V

4XDQWLW\2UGHUHG
;6XEWRWDORI$%&

'HVFULSWLRQ 'HVFULSWLRQ
'6&%$&\OLQGHU6WRUDJH
[
+(OHFWURQLF:DWHU/HYHO*DXJH
*$GGLWLRQDO5ROOHU$VVHPEO\
6XEWRWDO)URP$GGLWLRQDO6KHHW
V

&&XVWRPL]DWLRQ&DWHJRU\7RWDOV,WHPL]HEHORZ$WWDFKDGGLWLRQDOVKHHW V
LIQHFHVVDU\

1RWH
&XVWRPL]DWLRQRSWLRQVDUHPDQXIDFWXUHUQRQVWDQGDUGRSWLRQVZKLFKZHUHVXEPLWWHGDQGSULFHGLQ&RQWUDFWRUV VSURSRVDO

63DLQW'RRU-DPV 8&XVWRP5HIOHFWLYH6WULSH/D\RXW (3XPS(QJLQH)XHO&RQQHFWHGWRIXHOWDQN *$NURQ9DOYHV *3UHFRQQHFW'LVFKDUJH *
5'LUHFW)LOO
3
%URZ/LJKWRQ)URQWRI&KDVVLV&DE 3+LJK/XPHQ/('6FHQH/LJKWV 7:&XVWRP/HWWHULQJ 38SSHU=RQH%DQG'/LJKWLQJ 1&HQFRP6\VWHP '5ROO2XW7UD\VZLWKPDWWLQJ [

5%DWWHU\&KDUJHU,QYHUWHU 3&XVWRP/LJKWEDU
GNQREEH#GDQNRQHW
)RUGGUJDVFKDVVLV[)XOODOXPLQXPSDLQWHGERG\JDOORQZDWHU+3%ULJJVHQJLQH $3URGXFW,WHP%DVH8QLW3ULFH3HU&RQWUDFWRU
V+*$&&RQWUDFW

%3XEOLVKHG2SWLRQV,WHPL]HEHORZ$WWDFKDGGLWLRQDOVKHHW V
LIQHFHVVDU\

1RWH
3XEOLVKHG2SWLRQVDUHPDQXIDFWXUHUVWDQGDUGRSWLRQVZKLFKZHUHVXEPLWWHGDQGSULFHGLQ&RQWUDFWRU VSURSRVDO

,-------7

I I I I I I I I I I I I I I I I I I
,-------------7
I I I I I I I I I I I I L_ _______ I ______ J
r-------7
I I I I I I �� i� (51 I

TELESCOPIC LIGHTS
(WHELEN PCH2P LED)
1 ________ 1 _______________ _ 1 _______ _ : r"j I I I I I I [ _______ ] 15• ES TIMATEDANGLE OF DEPAR TURE
t----��--[-llil'-L --'--c:_.,....,=� -g-·""""'4---/...,._ _ _ LJ '.t�Y IC

ZONE B/O LIGHTS
(WHELEN M2WRC RED LED)
----------120' ________ __,
119' ---------
L3 II I
I��---��
--� _____ J i �i 'r---------1 I '\ I
./ :I:___
i--- 4 7' ---------------179' l,/HEELBASE------------i-------74'-----i 300' [25'] APPROXIMATE OVERALL LENGTH

LIGHTBAR
(\,/HELEN LIBERTY II LED)

GRILLE LIGHTS
22' 22'
96' BODY 1,/IDTH [B'J 102' [8'-6'] APPROXIMATE OVERALL 1,/IDTH 95' [7'-11'] APPROXIMATEOVERALL HEIGHT

UPPER ZONE WARNING LIGHTS
(WHELEN M6RC

RED LED)

LOWER ZONE WARNING LIGHTS
(WHELEN M6RC

RED LED)
Attachment 4
Council Agenda 9-1-2026 9.H-35

SALES DRAWING
Attachment 4
Council Agenda 9-1-2026 9.H-36

Pismo Beach City CouncilAugust 18, 2026

Pismo Beach City Council
August 18, 2026