Item 09 2024-01711 Cooperative Purchase Contract - Fire Ambulances — Sacramento City Council, October 22, 2024

City of Sacramento
City Council - 5PM Report
915 I Street Sacramento, CA 95814
www.cityofsacramento.org
File ID: 2024-01711 10/22/2024 Consent Item 9.

Cooperative Purchase Contract: Fire Ambulances
File ID: 2024-01711
Location: Citywide
Recommendation: Pass a Motion: 1) approving the use of the Houston Galveston Area Council of Governments (HGAC) cooperative purchase contract with Braun Northwest, Inc. (Contract AM10-23) for the purchase of two (2) new ambulances for a total amount not to exceed $545,715; and 2) authorizing the City Manager or the City Manager’s designee to take any necessary actions to complete the purchases specified above.

Contact: Alison Kerstetter, Fleet Manager, (916) 808-1163, [email protected]; Department of Public Works
Presenter: None
Attachments:
1-Description/Analysis
2-Contract
Description/Analysis
Issue Detail: The Department of Public Works, Fleet Management Division, is requesting approval to purchase two (2) new ambulances for the Sacramento Fire Department. These ambulances will be critical additions to the department’s emergency response fleet, directly supporting the delivery of critical care services to the citizens of Sacramento.

Policy Considerations: The recommendations in this report are in accordance with Sacramento City Code Chapter 3.56 which requires City Council approval of actions of $250,000or more and which provides for the use of cooperative purchase agreements without competitive bidding (Section

3.56.240).

Economic Impacts: None.

Environmental Considerations:

California Environmental Quality Act (CEQA): No environmental review is necessary

Page 1 of 2 ends

File ID: 2024-01711 10/22/2024 Consent Item 9.
because the recommendations in this report involve the purchase of vehicles and are not considered to be a project in accordance with Section 15378(b)(2) of the California Environmental Quality Act guidelines.

Sustainability: The recommended purchases are consistent with the Fleet Sustainability Policy adopted by City Council on December 12, 2017 (Resolution No. 2017-0478). There are no currently available zero emission options for ambulances that meet the City’s operational requirements.

Commission/Committee Action: None.

Rationale for Recommendation: After reviewing the available purchase options, the Fleet Management Division has determined that the HGAC cooperative purchase agreement with Braun Northwest, Inc. represents the most advantageous purchasing strategy. The contract was competitively bid nationally, and HGAC receives greater discounts from the manufacturer due to a higher purchase volume than the City would receive if issuing its own bid.

In an ongoing effort to maximize cost savings and staff resources, many government agencies share contracting efforts through cooperative purchasing. This procurement method increases pricing competitiveness and lowers operating costs through volume buying. When comparing the administrative costs of procurement, staff considers product research, source selection, specifications, advertising, staff reports, awarding, protest, and administration of the contract.

The City has used both regional and national cooperative purchase agreements to complement its own contracting initiatives. Cooperative purchasing enables City departments to evaluate a broader range of contracting opportunities and to share resources with other jurisdictions. Cooperative purchasing also leverages internal and external resources to maximize cost savings opportunities for the City.

Financial Considerations: The recommended purchase, in a total amount not to exceed $545,715 will be made from the Department of Public Works Fiscal Year (FY) 2024/2025 operating budget (Fleet Fund, Fund 6501) and will be charged to the Fire Department Advanced Life Support Equipment Program (F12000200). Sufficient funding exists in the Department of Public Works FY2024/25 operating budget and the Fire Department Advanced life Support Equipment Program (F12000200) due to savings on previous replacements to support the recommended purchase.

Local Business Enterprise (LBE): Braun Northwest, Inc. is not an LBE. The minimum LBE participation requirement is waived for the City’s use of cooperative purchase agreements that have been competitively bid, evaluated, and awarded by other governmental agencies that may or may not have similar LBE programs.

Page 2 of 2 ends

nnlii.JIV��IVU-u inc.
150 North Star Drive/ PO Box 1204 / Chehalis, WA 98532 I 360.748.0195 I 800.245.6303 I fox 360.748.0256 F.O.B.: Sacramento, CA
Delivery: Approximately 30-90 days, based upon options selected on options page.

Terms: Ninety percent (90%) payment due upon receipt of vehicle. Balance due in thirty (30) days.
*Note: Vehicle offered on first come first served basis and is being offered to other agencies, mileage accruing. *The above pricing includes one (1) round-trip travel charges for two people flying from Sacramento, CA for final inspection.
*The above pricing includes one (1) trip for one person from Braun NW to complete final punch list from City of Sacramento for one (1) vehicles. Punch list must be completed and submitted to Braun NW (7) days after delivery.

Braun NW will send technician for final punch list within (7) days after receipt of punch list. *Sales tax is based upon 8. 75% and NIA on HGAC fee and Delivery of units. (Note: This bid is contingent on use of customer's Government Ford Fleet Identification Number.) Failure to secure a FIN will increase the price by the amount of the GPC chassis discount.

Braun Northwest, Inc. is a California dealer (#16055) with insurance information available upon request.

Braun Northwest, Inc. is a Washington dealer (0991-A) with insurance information available upon request.

Respectfully Submitted by: We agree to accept the above proposal:

Brau orthwest, Inc. City of Sacramento
GQ)�
• McCallum, VP of Sales
Date: £11171 �
Signature Date
Printed Name Title
TM
cc BC/LM
Enclosures: Specifications, drawings.

EMERliENCY VEHICLE§ www.braunnw.com
9/4/2024
Alison Kerstetter Fleet Manager

9/4/2024
Alison Kerstetter Fleet Manager

BraunNW (BLI) 1 of 35 Ford Type-3 Demo
5/8/24 3812-3
BRAUN NORTHWEST, INC.

DETAILED SPECIFICATIONS
FOR

DEMONSTRATOR
E450, GAS, 167” MODULE, TYPE 3

COLOR/WHITE
VEHICLE #3812-3
1 CHASSIS

1.01 OEM CHASSIS
• 2024 Ford E-450, meeting all the specifications of Section 1.01. (Subject to model year changes)
– 3 year/36,000 mile ″Bumper to Bumper″ warranty
– 5 year/60,000 mile Powertrain warranty
– Ambulance Prep. Package 47H
– Dual rear wheels
– Twelve Frame Pucks (559)
– Provided by Braun Northwest

1.01.01 SPECIFIC RATINGS
• Drive – 4 x 2
• G.V.W.R. – 14,500 lb
• Front Axle – 5,000 lb
• Rear Axle – 9,450 lb
• Wheelbase – 158″
• Cab to Axle – 100″
• Curb Weight – 10,000 lb approximate
• Front Spring Capacity – 5,000 lb
• Rear Spring Capacity – 9,450 lb
• Rear Differential – 4.56 ratio, limited slip axle

1.01.02 POWER TRAIN
• Engine – Gasoline
– 7.3L V8 Premium (99N)
– Engine block heater
– Heavy duty dry type air cleaner with flow restriction indicator • Engine Cooling System
– Heavy duty, closed-air, free-liquid state type
– Coolant recovery system
– 50/50 solution Permanent type antifreeze to –40 degrees F • Transmission

BraunNW (BLI) 2 of 35 Ford Type-3 Demo
5/8/24 3812-3
– 6-speed automatic transmission with tow/haul mode
– Auxiliary transmission oil cooler
• Exhaust System
– System complies with Federal Motor Carrier Safety Regulations, Part 393.83 – Suspended using three hangers, excluding manifold attachment – Discharge at right rear side of module
– Tailpipe shall not terminate within twelve inches of the vertical axis of the fuel tank filler opening.
– Two exhaust heat shields mounted in mid -chassis, right -hand side for upfitter installed frame pucks

1.01.03 STEERING
• Power assisted
• Tilt and telescoping steering wheel

1.01.04 SHOCK ABSORBERS/STABILIZER BARS
• Heavy-duty shock absorbers front and rear
• OEM front and rear stabilizer bars

1.01.05 BRAKES
• Four Wheel Disc with Traction Control
– Hill Start Assist
– Traction Control
– Electronic Stability Control

1.01.06 TIRES AND WHEELS
• Seven OEM LT225/75R16E all-season steel belted radials • Seven OEM 16″ painted white steel wheels
• Spare tire and wheel
• Steel valve stems

1.01.07X ELECTRICAL
• Alternators – OEM dual heavy-duty, 397 amps total (63N) • Batteries – OEM dual heavy-duty, 78 amp-HR batteries

1.01.08 INSTRUMENT PANEL AND CONTROLS
• Gauges
– Speedometer
– Tachometer
– Coolant Temperature
– Oil Pressure
– Fuel Level
– Odometer/Trip Odometer
• Cruise Control
• Instrument Panel Message Center
• Dual USB ports in instrument panel
• Audio – Bluetooth-capable AM/FM stereo w/clock display, USB input • Four Speakers

1.01.09 CAB EXTERIOR

BraunNW (BLI) 3 of 35 Ford Type-3 Demo
5/8/24 3812-3
• Exterior Upgrade Package
– Bumper – Front, Chrome
– Grille – Chrome
• License Plate Bracket
• Horn – OEM dual electric
• Windshield wipers – Interval
• Telescopic Trailer Tow Mirrors with manual adjustments – Two black, below eye level, manually telescoping trailer tow – Power adjusted upper glass
• Lights
– Headlamps with Autolamp
– Dual sealed-beam with fixed lens
– Daytime Running Lamps, configurable
• Fuel tank – OEM 55 Gallons

1.01.10 CAB INTERIOR
• Seats – OEM
– Cloth covered high back Captain’s Chairs
– Combination lap and shoulder harness
• Climate Control – OEM
– Heavy duty, fresh air, high-capacity heater/defroster – Dehumidifying air conditioning system
• Auxiliary Heater-Air Conditioning Connector Package
• Airbags
– Driver and right-front passenger front
• Interior Upgrade Package
– High-series door trim panels
– Flooring – black vinyl
– Insulation Package
– Cloth sun visors
• Vinyl headliner
• Power windows & door locks
• Courtesy light switches on all doors
• Key-in-ignition Warning chime
• One 12-volt power point
• Day/Night Interior Rear-view Mirror

1.01.11 COLORS
• Exterior – Oxford White (YZ)
• Interior – Medium Flint Gray

BraunNW (BLI) 4 of 35 Ford Type-3 Demo
5/8/24 3812-3

1.02 CHASSIS MODIFICATIONS
The following modifications will be made to the chassis by Braun Northwest.

1.02.03 VALVE EXTENDERS
Stainless steel wheel simulators shall be installed on all outer wheels, with braided valve stem extenders on all four rear wheels.

1.02.04 EXHAUST HEAT SHIELDS
Shall be formed from 20 ga. galvanized sheet metal with stamped reinforcements and formed edges. Access openings shall be provided for shock absorber, mounting bolts, etc.

Heat shields shall be bolted to chassis frame and extend from back of cab to the frame cross member just behind the rear axle.

1.02.05 RUNNING BOARDS
Running boards made of 0.125″ bright aluminum diamond plate with front splash guards shall be installed on both sides of the cab, flared towards the front corners of t he module, and securely mounted with stainless steel 1/4″-20 truss head bolts.

1.02.07 AUTO THROTTLE
An Intermotive voltage monitor shall be installed to automatically adjust the auto throttle for changes in electrical load and AC loads.

1.02.09 MUD FLAPS
Mud flaps with the ″NORTH STAR″ logo shall be installed behind each rear wheel.

BraunNW (BLI) 5 of 35 Ford Type-3 Demo
5/8/24 3812-3

1.03 MODULE-TO-CHASSIS MOUNTING SYSTEM

1.03.01 MODULE MOUNTING SYSTEM
Module mounting system shall be designed and used as supplied by chassis manufacturer.

It shall consist of twelve rubber puck mounts secured with chassis manufacturer-supplied

0.50″ hardened bolts.

1.03.02D CAB-TO-MODULE ATTACHMENT
The module shall be attached to the cab by twenty 5/16″ Grade 5 plated steel bolts with nylon insert locking nuts. Access plates shall be provided in the bulkhead wall for the servicing of cab-to-module bolts or for remounting of the body.

1.03.03 CAB-TO-MODULE GASKET
A closed-cell, neoprene, weatherproof gasket shall be installed between the cab and module to minimize electrolytic corrosion.

BraunNW (BLI) 6 of 35 Ford Type-3 Demo
5/8/24 3812-3
2 MODULAR CONSTRUCTION
All material utilized shall be of the correct type, alloy, and thickness to withstand the intended usage and provide protection against cracking, corrosion, or metal fatigue. All materials utilized shall be of open stock origin, commonly available through local sources, for rapid and economical repair or modification of the body. Any use of proprietary parts or materials in the construction of the body is unacceptable, due to potential delays or difficulties in future repairs or service. NO EXCEPTIONS TO BE TAKEN IN THIS AREA. This specification has been designed and written to fill specific needs of this agency. Where brand name, make, or model of equipment has been specified, no exceptions shall be allowed. Where compartment and cabinet sizes have been specified, bidder must bid substantially (plus or minus 1″) the size specified.

The module shall have a transferable lifetime structural warranty.

2.01 MATERIAL

EXTRUSIONS SIZE ALLOY
Structural Tubing 1ʺ x 2ʺ x 0.125ʺ sq 6063-T52
Structural Tubing 2ʺ x 2ʺ x 0.125ʺ sq 6063-T52
Structural Angle Cross Members 3ʺ x 3ʺ x 0.375ʺ 6061-T6 Structural Channel Cross Members 1.5ʺ x 3ʺ x 0.25ʺ 6061-T6

FORMED SHEETING SIZE ALLOY
Skin/Roof/Compartments/Subfloors/Doors 0.125ʺ 5052-H32
Interior Cabinets 0.090ʺ 5052-H32
Diamond Plate 0.125ʺ/0.08ʺ 3003-H22
Stainless Steel 16 ga., 20 ga 304 # 4B

2.02 MODULE DIMENSIONS
Overall Vehicle Dimensions (Specifications are listed as minimums.) Length 22 ′ 1.75 ″ 265.75 ″
Width (excluding mirrors) 8 ′ 0 ″ 96.00 ″
Height (Approximate) 8 ′ 11.13 ″ 107.13 ″
Exterior Module Dimensions (Specifications are listed as minimums.) Length 13 ′ 11 ″ 167.00 ″
Width 8 ′ 0 ″ 96.00 ″
Height 7 ′ 4.375 ″ 88.38 ″
Interior Dimensions (Specifications are listed as minimums.) Length Forward Wall to Rear Wall 159.00 ″
Width Left Wall to Right Wall 89.00 ″
Floor Width Left Cabinets to Squad Bench 50.25 ″
Height Floor to Ceiling 72.00 ″
Load Height (Approximate) 33.00 ″

BraunNW (BLI) 7 of 35 Ford Type-3 Demo
5/8/24 3812-3

2.03 STRUCTURAL FRAMING
Side wall and rear wall construction shall consist of 2″ x 2″ x 0.125″ aluminum square tubing extensions welded together with a maximum of 14″ centers. 1″ x 2″ x 0.125″ aluminum tubing may be utilized in addition to 2″ x 2″ tubing to accommodate custom compartment sizes. The bottom of the wall structure shall be sealed with a welded 2″ x 2″ tube, a 2″ x 2″ angle, or a 0.125″ plate depending upon location. The wall structure shall be capped with a 2″ x 4″ x 0.125″ header upon which a 2″ x 2″ x 0.125″ roof st ructure is welded. This process provides a unitized roll cage structure for greater occupant safety.

The front wall structure shall be constructed of formed aluminum channels to allow ample space for wiring raceways, heater hoses, and A/C hoses.

2.04 FOUNDATION SYSTEM
The foundation system shall consist of a 0.125″ aluminum sheet subfloor with foundation members securely welded under the subfloor. Transverse members (laterals) shall consist of 3″ x 3″ x 0.375″ structural angles with 1.5″ x 3″ x 0.25″ channel(s) above the fuel tank.

0.25″ x 1.5″ aluminum stringers shall span longitudinally between the laterals.

2.05 MODULE SEAMS
All body and compartment seams at or below floor level shall be full -seam-welded. The entire perimeter of the subfloor shall be co mpletely sealed with a caulking material, creating a watertight seam.

2.06 EXTERIOR SKIN
A Norton NORBOND closed-cell, polyurethane foam tape with high-performance acrylic adhesive shall be utilized full length on all front and rear wall and roof frame members. A polyurethane adhesive sealant shall be applied to the edges of framing members that are bonded with NORBOND tape. An advanced two -part methacrylate structural adhesive shall be used to bond all side wall tubes to the exterior skin and door frames.

The module shall be constructed utilizing full -size sheet construction to minimize body seams. There shall be no corner or mid-body seams.

2.07 MODULE ROOF
In order to improve module strength and minimize exposed seams, the roof shall be seamed transversely, shall be crowned, shall have a 1.5″ radius along the edges, and shall be welded to 2″ x 4″ wall header tubes 4.75″ below the roof line. The roof shall be supported by positive contact between sidewall framing and roof framing. All seams on the roof surface shall be continuously welded and body -worked on the outside. In order to avoid the possibility of paint and/or weld cracking, no extrusions shall be used in the ex terior construction of the roof or corners of the module.

A contoured, 3/8″ aluminum plate, painted to match the module, shall be welded to the roof structure and project through the center of the roof to serve as anchorage for personal fall arrest equipment. The anchorage is designed and rated for a single person only.

The module roof front and rear edges shall be constructed to allow mounting of recessed lightbars.

BraunNW (BLI) 8 of 35 Ford Type-3 Demo
5/8/24 3812-3

2.08 MODULE EXTERIOR COMPARTMENTS
All compartments shall be constructed from formed 0.125″ aluminum, securely welded to the subfloor and structural framing. A baffled drain hole shall be provided in all exterior compartment bottoms that extend below the floor line. All exterior adjustable shelves shall be mounted on heavy -duty aluminum track, which is securely welded to compartment interiors. Each shelf shall support at least 300 lb of equipment.

COMPARTMENT #1
Interior Dimensions – 55”W x 38”H x 20”D
Doorway Dimensions – 54”W x 38”H
Location – Street side, forward
Shelving – Two adjustable: one bin type 17.5” W, one full width (shipped loose).

Door(s) – Double
Light(s) – One vertical LED strip light
Additional Instructions –

1. The 120VAC Power Box shall be installed in the forward wall (Section 6.21 related), recessed so as not to protrude into the compartment.

2. Compartment will have four vertical strips of heavy-duty aluminum track on the back wall. This will allow the bin shelf to be installed fore or aft in the compartment. The forward wall of the bin shelf shall be notched to allow better access to the 120VAC box.

3. Two vertical strips of heavy-duty aluminum track shall be added to each of the side walls for future installation of a full -length shelf to be shipped loose (Section 8.01 related).

4. A spare tire mount shall be mounted on the back wall of the aft section (Section 4.19 related).

5. A 120VAC GFCI duplex receptacle shall be installed on the forward wall, lower (Section 6.21 related).

6. A vent with MERV 8 polyester filter media and a hex-punched stainless-steel cover shall be installed on the forward wall.

COMPARTMENT #2
Interior Dimensions – 32”W x 77”H x 20”D
Doorway Dimensions – 32”W x 70”H
Location – Street side, rear
Shelving – One full width adjustable shelf
Door(s) – Single
Light(s) – One vertical LED strip light
Additional Instructions –

1. Two heavy-duty aluminum tracks will be installed on back wall to accommodate a bin- type shelf.

2. A slide-out tool board with 20″ slides, grab hole, gas shock, bracket and strap shall be installed by BNW in Compartment #2 for storage of a customer-supplied-and- installed Stryker stair chair.

3. Shall have a spring hanger close out located in forward back corner of the compartment that allows for leaf spring travel.

4. Two vents with MERV 8 polyester filter media and a hex-punched stainless-steel cover shall be installed one each on the forward and aft wall.

BraunNW (BLI) 9 of 35 Ford Type-3 Demo
5/8/24 3812-3
COMPARTMENT #3
Interior Dimensions – 22”W x 77”H x 20D
Doorway Dimensions – 22”W x 70”H
Location – Curbside, rear
Shelving – One 13.5” bin type shelf
Door(s) – Single
Light(s) – One vertical LED strip light
Additional Instructions –

1. This compartment shall have a welded bracket, painted to match the compartment, and three ratcheting straps with UHMW stiffeners set up for stor age of a customer- supplied-and-installed H or M-size cylinder (Section 4.10 related).

2. Two backboard restraining straps shall be installed on the aft wall. A formed stainless- steel gasket cover shall be installed so that backboards do not cut gasket material.

3. A vent with MERV 8 polyester filter media and a hex -punched stainless-steel cover shall be installed on the aft wall.

COMPARTMENT #4
Interior Dimensions – 18”W x 24.75”H x 20”D (16”D at floor) Doorway Dimensions – 16”W x 24.75”H
Location – Curbside aft of wheel well
Shelving – None
Door(s) – Single
Light(s) – One vertical LED strip light
Additional Instructions –

1. Shall have a spring hanger close out located in the back of the compartment that allows for leaf spring travel.

COMPARTMENT #5
Interior Dimensions – 25.75”W x 49.25”H x 27.5”D
Doorway Dimensions – 25.75”W x 49.25”H
Location – Curbside, forward
Shelving – See Interior Cabinet #19
Door(s) – Single
Light(s) – One vertical LED strip light
Additional Instructions –

1. This compartment shall provide inside/outside access to Cabinet #19 with a full width stainless steel threshold on the floor level shelf.

2. The below-floor portion of this compartment shall be for battery storage, with a rollout tray capable of holding two OEM batteries. The area shall be vented to the outside and sealed to prevent battery vapors from entering the patient area (Section 6.24 related).

2.09 MODULE DOORS
The doors shall be box-pan-formed with a total thickness of 2″.

2.09.01 DOOR FRAMES AND SEALS
Each door frame shall have a flange for the installation of an air cell hollow core 360 - degree compression door seal. This seal creates watertight, dust -free compartment integrity. Door seal shall be knock -on type. Door fram es shall be bonded to the adjacent tubes such that no exterior flange is required.

BraunNW (BLI) 10 of 35 Ford Type-3 Demo
5/8/24 3812-3

2.09.02 DOOR HINGES
Compartment and passage doors shall have full -length, piano-type, 2.5″W stainless steel hinges, positioned with 0.25″ rivets at each end. The hinges shall be attached with #12 x

0.75″ stainless steel truss head screws spaced 4″ apart, sealed with Sikaflex. All curbside and streetside side -hinged doors shall be hinged on the forward sides, and all rear side - hinged doors shall be hinged on the outboard sides.

2.09.03 DOOR LATCHES
Exterior door handles shall be semi -flush, chrome -plated Eberhard E Grabber #21 100.

Passage doors shall have release handles on the inside of each door. All exterior doors shall have rotary latches and striker posts that meet FMVSS 206 requirements. Striker posts shall be adjustable and be secured with a nut from behind the door fram e. The striker washer shall not be removed. Doors greater than 45″ tall shall have double rotary latches activated by stainless steel rods. Once final adjustments have been made, threads shall have Loctite or equivalent applied. All double -door compartments shall have an exterior E Grabber handle and rotary latches on each door. Doors shall latch to doorframe -mounted striker posts only and not to one another. Curbside passage and rear curbside doors shall have interior handles with dual-point, rod-actuated, rotary latch systems that are lockable inside and out. All locks shall be keyed J236.

The side and rear passage doors shall all have emergency release levers, one at the top and bottom of each door and accessible from the inside of the module.

2.09.04 COMPARTMENT DOOR CONTROL
A heavy -duty, double -spring door control capable of holding the door open at approximately a 90-degree angle on any road surface shall be installed at the top of each compartment door.

Two 2″ black seatbelt-style straps with footman loops shall be installed, one each at the top and bottom of the door frame, of Compartment #1 forward and aft doors, to protect the doors from excessive overtravel.

2.09.05 CURBSIDE DOOR CONTROL
A heavy-duty, double spring door check capable of holding the door open at approximately a 90-degree angle on any road surface shall be installed at the top of the curbside passage door.

Two 2″ black seatbelt-style straps with footman loops shall be installed, one each at the top and bottom of the door frame, to protect the door from excessive overtravel.

2.09.06 REAR DOOR CONTROL
Rear door controls shall be two grabber -type hold-open devices with replaceable rubber catches.

2.09.07 COMPARTMENT DOOR SKINS
Each compartment door skin shall be made of 0.080″ bright aluminum diamond plate, shall be removable, and have a latch service opening with a 2.25″ x 4.5″ black rubber plug for lubrication and service. Door skins shall be secured with #8 pan head screws and Sikaflex.

Red/white 1.5″ conspicuity tape shall b e installed on the outboard vertical edge of each door.

BraunNW (BLI) 11 of 35 Ford Type-3 Demo
5/8/24 3812-3

2.09.08 ENTRANCE DOOR SKINS
Each entrance doorskin shall be made of 0.080″ bright aluminum diamond plate and be removable to service door hardware. A removable stainless-steel bezel shall be installed at mid-height on the door skin to provide access to the latch hardware and electric lock motors (Section 6.40 related). Red/white 1.5″ conspicuity tape shall be installed on the top, bottom, and vertical edges of the side passage door and curbside rear door. The streetside rear door shall have conspicuity tape on the top and bottom edges.

2.09.09 ENTRANCE DOORWAYS
One curbside and two rear module entrance doors shall be provided. The curbside doorway dimensions shall be 31ʺW x 73.75ʺH. The rear doorway dimensions shall be 49.75ʺW x 66ʺH.

2.09.10 THRESHOLDS
All compartment and module access door frames shall have full-width-formed stainless- steel threshold plates to protect the lower edge of frame.

2.10 MODULE INTERIOR CABINETS
Shall be formed of 0.090″ aluminum and shall be securely welded or mounted to the structural framing. All interior adjustable shelves shall be mounted on 1″ wide aluminum track.

CABINET #1
Dimensions – 39.5”W x 13.75”H x 15.75”D
Location – Street side, upper forward
Shelving – One adjustable, aft of divider
Door(s) – Sliding clear 0.25 ” polycarbonate with felt -lined anodized aluminum track , interlocking aluminum trim, and full extruded aluminum door pulls with integral door latch Lighting – LED under-cabinet strip light (Section 6.14 related) Additional Instructions –

1. Cabinet shall be divided in the center by a vertical fixed divider.

2. An IV Warmer with a 4” surround shall be located in the lower aft corner of this cabinet (Section 6.35 related).

3. One 120VAC GFCI duplex receptacle shall be installed on the back wall of the cabinet (Section 6.21 related).

CABINET #2
Dimensions – 43.5”W x 7”H x 15.75”D
Location – Streetside above CPR seat
Shelving – None
Door(s) – Sliding clear 0.25 ” polycarbonate with felt -lined anodized aluminum track, interlocking aluminum trim, and full extruded aluminum door pulls with integral door latch.

Lighting – None
Additional Instructions – None

BraunNW (BLI) 12 of 35 Ford Type-3 Demo
5/8/24 3812-3
CABINET #3
Dimensions – 26”W x 13.25”H x 15.75”D
Location – Streetside upper rear
Shelving – One adjustable
Door(s) – Sliding clear 0.25 ” polycarbonate with felt -lined anodized aluminum track, interlocking aluminum trim, and full extruded aluminum door pulls with integral door latch.

Additional Instructions – None

CABINET #4
Dimensions –26”W x 13.25”H x 20”D
Location – Streetside center rear
Shelving – One adjustable
Door(s) – Sliding clear 0.25 ” polycarbonate with felt -lined anodized aluminum track, interlocking aluminum trim, and full extruded aluminum door pulls with integral door latch.

Lighting – LED under-cabinet strip light (Section 6.14 related) Additional Instructions – None

CABINET #5
Dimensions – 27”W x 15”H x 20”D
Location – Streetside, open area aft of CPR seat
Shelving – None
Door(s) – None
Additional Instructions –

1. A 120VAC GFCI duplex receptacle shall be located in the lower left area of the back wall (Section 6.21 related).

2. A full depth one-piece 16-gauge, 304 stainless steel countertop with a 0.5″ aluminum retaining lip and aluminum cove trim along the wall shall be installed.

CABINET #6
Dimensions – 26”W x 18”H x 20”D
Location – Streetside lower rear
Shelving – One adjustable
Door(s) – Sliding clear 0.25 ” polycarbonate with felt -lined anodized aluminum track, interlocking aluminum trim, and full extruded aluminum door pulls with integral door latch.

Additional Instructions – None

BraunNW (BLI) 13 of 35 Ford Type-3 Demo
5/8/24 3812-3
CABINET #7 – CPR Seat with Storage
Dimensions – Bench: 26”W x 18.75”H x 20”D
Storage: 26”W x 7.625”H x 20”D
Location – Streetside aft of Action Area
Shelving – None
Door(s) – Hinged aluminum bench lid, with removable high-density foam padding covered with seamless vinyl shall provide access to the storage area. It shall have a 1.5” overhang, an automatic hold-open device, and stainless steel paddle latch.

Additional Instructions –

1. A 4-point, single-buckle seat belt with below-the-bench retractors shall be installed.

2. The CPR 4-point seat back and/or head pads shall have high -density foam padding covered with seamless vinyl.

3. The CPR seat base to be formed from aluminum and securely anchored to sub-floor.

The bottom and unfinished sides of the storage area shall be sprayed with textured polyurea and painted white with gray splatter.

CABINET #8 – Action Area
Dimensions – 59.125”W x 28.75”H x 20”D
Location – Streetside forward of CPR seat
Shelving – None
Door(s) – None
Additional Instructions –

1. It shall contain the following items:
a. One oxygen outlet (Section 5.11 related)
b. Vacuum connection (Section 5.12 related)
c. Suction collector (Section 5.12 related)
d. Attendant control panel (Section 6.13 related)
e. Inverter status panel (Section 6.31 related)
f. Digital thermostat (Section 5.17 related)
g. One 120VAC GFCI duplex receptacle (Section 6.21 related) h. One 12VDC receptacle (Section 6.25 related)

2. One Becton Dickinson 8.2 qt. sharps contain er and one 7 qt. waste container shall be installed at the aft end of the Action Area countertop, with a hinged clear polycarbonate cover with a finger hole.

3. A full depth one-piece 16 gauge, 304 stainless steel countertop with a 0.5″ aluminum retaining lip and aluminum cove trim along the wall shall be installed.

CABINET #9
Dimensions – 36.75”W x 7”H x 9”D
Location – Curbside upper rear
Shelving – None
Door(s) – Sliding clear 0.25 ” polycarbonate with felt -lined anodized aluminum track, interlocking aluminum trim, and full extruded aluminum door pulls with integral door latch.

Additional Instructions – None

BraunNW (BLI) 14 of 35 Ford Type-3 Demo
5/8/24 3812-3
CABINET #10
Dimensions – 36.75”W x 7”H x 9”D
Location – Curbside upper forward
Shelving – None
Door(s) – Sliding clear 0.25 ” polycarbonate with felt -lined anodized aluminum track, interlocking aluminum trim, and full extruded aluminum door pulls with integral door latch.

Additional Instructions – None

CABINET #11
Dimensions – 13”W x 25”H x 5.5”D
Location – Curbside, aisle side of right front stack
Shelving – None
Door(s) – Tip-out bottom-hinged painted aluminum door with a Southco C2 latch and nylon travel stop strap
Additional Instructions –

1. This cabinet shall provide storage for two customer-supplied-and-installed ″D″ oxygen cylinders (Section 5.35 related). A stainless-steel spring with dual flaps shall be installed to prevent cylinder rattling.

CABINET #12 – Squad Bench with Storage
Dimensions – Bench: 70” W x 18.75”H x 20”D
Storage: 39”W x 7.625”H aft, 12.75”H forward x 20”D
Location – Curbside
Shelving – None
Door(s) – Hinged aluminum split lid bench, with high-density foam padding covered with seamless vinyl shall provide access to the storage area. It shall have a 1.5 ” overhang, an automatic hold-open device, and a stainless-steel paddle latch.

The forward lid shall provide access to the storage area. The aft lid shall be fixed. The pad shall be removable.

Additional Instructions –

1. The squad bench back and head pad shall have high -density foam padding covered with seamless vinyl. Two four -point single -click seat belt s with below -the-bench retractors shall be installed. Three two-point automatic locking retractor seat belts shall be installed on the bench with three additional lower receivers, set up for stretcher patients.

2. The squad bench base to be formed from aluminum and securely anchored to sub-floor.

The bottom and unfinished sides of the storage area shall be sprayed with textured gray polyurethane and painted white with gray splatter.

3. An Oxygen window shall be installed in the forward-facing wall at the aft end of the bench.

4. An Oxygen outlet and a momentary rocker switch to activate the dome timer shall be installed on the curbside wall over the bench (Section 6.16 related).

5. A bench end restraint bar shall be installed on the forward end of the squad bench (Section 5.34 related).

BraunNW (BLI) 15 of 35 Ford Type-3 Demo
5/8/24 3812-3
CABINET #13 – HVAC
Dimensions – 34.75”W x 14.5”H x 27.875”D
Location – Front, right upper
Shelving – None
Door(s) – None
Additional Instructions –
• This cabinet shall house the heater/AC unit and the suction pump (Section 5.12 & 5.17 related).

CABINET #14 – Electrical Cabinet
Dimensions – 32”W x 16”H x 10”D
Location – Front, center over pass-thru
Shelving – None
Door(s) – Painted a luminum, top hinged door with a hold -open device, a quarter turn slotted latch, and an automatic cabinet light.

Additional Instructions –

1. This cabinet shall house the electrical component module. An atomic-controlled clock shall be installed on the face of this cabinet (Section 5.24 related).

CABINET #15
Dimensions – 18.75”W x 25”H x 10”D
Location – Front, forward of action area
Shelving – Two adjustable shelves
Door(s) – None
Additional Instructions – None

CABINET #16 – Electronics Cabinet
Dimensions – 16”W x 51”H x 10”D
Location – Front, behind attendant seat
Shelving – None
Door(s) – Aft facing, painted aluminum lift off panel with two SouthCo latches and upper and lower punched areas (Different than shown in drawings) Additional Instructions –

1. Two vertical heavy duty aluminum tracks shall be installed on the back wall. This cabinet is intended for electronic component storage and shall be supplied with access to electrical component panel. Antenna cables shall terminate in this cabinet.

2. The inverter shall be installed in this cabinet, on the back wall, lower (Section 6.31 related).

CABINET #17
Dimensions – 27.25”W x 14”H x 23.875”D
Location – Front, right center
Shelving – One adjustable
Door(s) – Sliding clear 0.25 ” polycarbonate with felt -lined anodized aluminum track, interlocking aluminum trim, and full extruded aluminum door pulls with integral door latch Additional Instructions – None

BraunNW (BLI) 16 of 35 Ford Type-3 Demo
5/8/24 3812-3
CABINET #18 – Drawer
Location – Front, right below Cabinet #17
Additional Instructions –

1. There shall be one 23”W x 5”H x 19”D metal drawer. Drawer shall operate on slides rated at 300 lb. per set and have a gas shock hold open/closed device and non-locking paddle slam latch to ensure drawer does not accidentally open or close during operation of the vehicle. Drawer shall be of formed 0.125 ” aluminum construction, painted to match the interior. Drawer shall have machine-stamped divider supports along the front and back with four removable ABS dividers.

CABINET #19 – Inside/Outside Access
Dimensions – 25.75” W x 33.5”H x 23.875” D
Location – Front, right lower
Shelving – Two adjustable, with 1” x 1” lip down facing doorway. Each shelf shall have a 3” hole for cord access.

Door(s) – Two clear 0.375″ polycarbonate side -hinged doors with paddle latches. Each door shall have two 20 ga stainless steel braces, 0.375″D steel rods, and slam latches rated for 750 lb. each.

Additional Instructions –
– This cabinet shall be accessible from the outside via exterior Compartment #5.

2. One 120VAC GFCI duplex receptacle and one 12VDC receptacle shall be installed in the upper forward portion of the forward wall (Section 6.21 & 6.25 related).

3. The HVAC shall be distributed thru a vertical plenum on the aisle side of the right front stack.

2.11 SIDE DOORSTEP
A recessed curbside doorstep shall be provided which is 11.5″ deep x 31″ wide. There shall be a drain hole and light gray Matéflex floor tile which is removable for cleaning purposes.

Aluminum diamond plate kick panel shall be installed on the sides and face of the doorstep.

2.12 FRONT MODULE WALL RECESS
Shall be recessed 8″ into the module body to provide for maximum adjustment of cab seats.

2.13A CAB TO MODULE PASSAGE
Shall be a walk-thru measuring 18.25″W x 48″H.

A clear 0.375″ polycarbonate sliding door with extruded aluminum right angle door pulls on the cab side shall be installed, to slide behind the driver's seat. The door shall be latchable in the open and closed positions.

2.14 WHEEL WELL LINERS
Wheel well liners made of formed aluminum shall be installed in the module wheel well openings.

2.15 ELECTROLYSIS PREVENTION
All external materials and fasteners shall be selected to prevent electrolysis and corrosion due to dissimilar materials and exposure to the elements. The m odule shall be painted before any exterior items (hinges, latches, door hold opens, etc.) are installed to provide an isolating film between dissimilar materials. Exterior fasteners used for direct connection to painted aluminum surfaces shall be coated with a corrosion inhibitor.

BraunNW (BLI) 17 of 35 Ford Type-3 Demo
5/8/24 3812-3
3 COATINGS AND FINISHES

3.01 MODULE FINISH PREPARATION
The module shall be seam sealed and all imperfections on aluminum surfaces of module shall be sanded smooth. The entire exterior shall be mechanically etched and washed with wax-and-grease-remover to ensure proper primer/sealant adhesion.

3.02 MODULE PRIMER
Module shall be sealed with a two -component, low VOC, direct -to-metal epoxy primer/sealant prior to applying the finish coat of acrylic urethane paint.

3.03 PAINT TYPE
Shall be Sherwin Williams acrylic urethane.

3.04 COLOR SCHEME
Base color to match Oxford White (GLV-11291704)

Stripe #1 Color: Blue Multi Stripe
Width: 6” total, 0.25” pinstripe with 0.25” gap, 5” stripe with

0.25” gap 0.25” pinstripe
Style: Beltline
Material: Vinyl
Location: Streetside, Curbside and rear of module

3.04.01 CHASSIS COLOR
Chassis shall be OEM Oxford White (YZ) (Section 1.01.11 related).

3.05 LETTERING/DECALS

STREET SIDE VIEW DEMO

Item #S1 Decal: “North Star”
Color: Blue
Size: 4” Lettering
Material: Vinyl
Location: Street side of Module centered

Item #S2 Decal: “Emergency Vehicles”
Font: Serpentine bold
Color: Blue
Size: 3”H x 51.25” L
Material: Vinyl
Location: Streetside of module centered below Item #S1

BraunNW (BLI) 18 of 35 Ford Type-3 Demo
5/8/24 3812-3

CURBSIDE VIEW DEMO

Item #C1 Decal: “North Star”
Color: Blue
Size: 4” Lettering
Material: Vinyl
Location: Curbside of module centered

Item #C2 Decal: “Emergency Vehicles”
Font: Serpentine bold
Color: Blue
Size: 3”H x 51.25” L
Material: Vinyl
Location: Curbside of module centered below Item #C1

3.06 COMPARTMENT FINISH
All compartments shall be sanded, etched, washed, primed, coated with textured polyurea thermoplastic elastomer finish and painted white with light gray splatter paint. (G2-33631 Alt 2 / GLV-51748)
All shelves and trays shall be sanded, etched, washed, primed, and painted white with light gray splatter paint. (G2-33631 Alt 2 / GLV-51748)

3.07 INTERIOR CABINETRY FINISH
All interior cabinetry shall be sanded, etched, washed, primed, coated with textured polyurea thermoplastic elastomer, and painted white w ith light gray splatter paint. (G2 - 33631 Alt 2 / GLV-51748)
All drawers, shelves and trays shall be sanded, etched, washed, primed, and painted white with light gray splatter paint. (G2-33631 Alt 2 / GLV-51748)

3.08 MODULE UPHOLSTERY
Module upholstery material shall be Dove Gray Spradling Perform 60 seamless vinyl.

3.09 MODULE FLOORING MATERIAL
Shall be Genome (#TFM2702) Altro Transflor Meta Slip -Retardant Sheet flooring providing durability, ease of maintenance and stain resistance. It shall contain a high concentration of microscopic aluminum oxide particles and colored quartz crystals suspended throughout the thickness with silicon carbide grains in the entire wear surface for slip-retardant performance. It shall have an overall thickness of 0.11″ nominal. Flooring shall be manufactured for Wear Resistance to meet ASTM C 501, indentation resistance in accordance with ASTM F 1303 and ASTM F 970, Grade 1 standards, shall meet ASTM D 2047 Slip Retardant, ASTM F 970 Static Load, ASTM E648, CMVSS, FMVSS 302, CAN ULC S102.2 Fire Data Tests. (Section 5.04 related)
An insulated floor shall be installed over the 0.125″ aluminum subfloor and shall be comprised of 0.75″ thick polyiso insulation between 0.75″ x 0.75″ x 0.063″ square tubing, covered with a 0.125″ aluminum sheet (Section 2.04 related).

Floor covering material shall be seamless and cove up the side walls a minimum of 5″ as a seal.

BraunNW (BLI) 19 of 35 Ford Type-3 Demo
5/8/24 3812-3

3.10 COMPARTMENT LINING
Compartment floors shall be lined with light gray Matéflex floor tile and all shelves with mat.

3.11 CABINET LINING
Interior cabinet shelves shall be lined with easy sweep mats which are removable for ease of cleaning.

3.12 SURFACES AND FINISHES
All patient compartment surfaces and finishes shall be impervious to soap, disinfectants, and water, to permit washing and sanitizing.

BraunNW (BLI) 20 of 35 Ford Type-3 Demo
5/8/24 3812-3
4 MODULE EXTERIOR

4.01 STEP/BUMPER
The rear bumper shall be a welded construction of 3″ x 3″ x 0.375″ aluminum angle and

1.5″ x 0.25″ flat bar and shall be covered by 0.125″ bright aluminum diamond plate. The center section, below the doors, shall have a hex -punched open flow de sign to prevent accumulation of water and snow and provide a 7″ step. Both outermost ends shall be angled to prevent dragging of corners in high angle of departure areas. Diamond plate shall be formed on front and rear edges for channel -type strength, and a formed 0.090″ aluminum closeout shall be welded to the underside of the bumper. The bumper shall be bolted directly to the chassis frame using high strength Grade 5 bolts. Bumper shall be easily removable and replaceable in case of damage. Bumper to be d esigned to accommodate a one-person-style cot.

4.02 RUB RAILS
Bright finished extruded aluminum rub rails of a double channel design shall be installed along the lower streetside and curbside edges of the module. Rub rails shall be 2.5″H x

0.75″W x 0.125″D, with a 0.5ʺH red/white conspicuity reflective tape installed in the insert area.

4.03 FENDER RINGS
Bright polished aluminum fender rings with a rounded outer edge shall be installed on the module, following the full contour of the wheel well opening.

4.04 DRIP RAIL
Extruded, anodized aluminum drip rails shall be installed the full length of the module front, rear, and sides near the roof . Drip rails shall be installed with bonding tape and mechanical fasteners on each end that shall withstand exposure to the elements. They shall be finished with 45-degree angled ends to avoid hooking materials which brush against the vehicle causing damage.

4.05 ROCK GUARDS
Bright aluminum diamond plate rock guards shall cover the front module corners, 24″ up from bottom of module, 2.5″ wrapped around the sides of module, and meet the cab at the front of the module.

4.06 REAR KICK PANEL
A bright aluminum diamond plate rear kick panel shall extend from the bottom edge of the module up to the bottom of the rear doors, full-width formed and wrapped 2.5″ around the sides of the module.

4.07 FUEL FILL
A polished cast aluminum fill well shall be installed on the streetside of the module and be properly vented. Fill and vent hoses shall be installed and protected in accordance with the chassis bodybuilder recommendations.

BraunNW (BLI) 21 of 35 Ford Type-3 Demo
5/8/24 3812-3

4.08 MODULE WINDOWS
All module windows shall have black anodized aluminum frames, rubber gaskets, be dark- tinted and shall be attached with screws for ease of replacement. The side passage door window shall be 18.75″ x 18.75″ with sliding glass, a positive catch, and a screen. The rear door windows shall be 18.75″ x 18.75″ fixed glass to prevent exhaust from entering the module.

4.09 FUEL SPLASH GUARD
A stainless-steel fuel splash guard shall be installed below the fuel fill.

4.10 EXTERIOR CYLINDER STORAGE
Compartment #3 shall have a welded bracket, painted to match the compartment, and three ratcheting straps with UHMW stiffeners set up for storage of a customer-supplied-and- installed H or M-size cylinder.

4.16B REAR LICENSE PLATE
A recessed license plate holder with dual Whelen #0AC0EDCR LED lights with angled chrome bezels shall be installed below rear doors in the rear kick panel (Section 4.06 related).

A hidden unlock switch shall be installed behind the license plate (Section 6.40 related).

4.19A SPARE TIRE MOUNT
An aluminum mounting plate for the OEM spare tire shall be installed in Compartment #1.

The spare tire shall be mounted on the bracket.

4.27 STAIR CHAIR STORAGE
A slide-out tool board with 20″ slides, grab hole, gas shock, bracket and strap shall be installed by BNW in Compartment #2 for storage of a customer-supplied-and-installed Stryker stair chair.

4.34 AUTOMOTIVE UNDERCOATING SEAL
The chassis and module underbodies (excluding the area above the fuel tank, driveline, and exhaust lines, per manufacturer’s specifications) shall be sprayed with undercoating for reduced corrosion and added sound deadening.

BraunNW (BLI) 22 of 35 Ford Type-3 Demo
5/8/24 3812-3
5 MODULE INTERIOR
All interior hangers, suppor ts, fasteners, latches, and hinges shall be of a near -flush-type design. The patient compartment shall be free of sharp projections. Exposed edges and corners shall be broken with a radius or protected with 1″ high-density foam covered with heavy-duty vinyl color-matched upholstery.

5.01 UPPER WALL COVERING
The upper module interior walls shall consist of light gray, heavy-grade, 0.125″ ABS vinyl panels attached to the wall structure with a closed -cell polyethylene foam tape coated on both sides with a permanent acrylic-based pressure-sensitive adhesive.

5.02 HEADLINER
The headliner shall be 0.125″ aluminum which is sanded, etched, washed, primed, and coated with textured polyurea thermoplastic elastomer, and painted white with light gray splatter paint (G2-33631 Alt 2 / GLV-51748).

5.03 HEAD PADS/CUSHIONS
Head pads located over all module access openings shall be 1.5″ foam covered with heavy- duty seamless vinyl upholstery. Head pads and seat backs for seating positions shall be

1.5″ foam covered with heavy-duty seamless vinyl upholstery.

Seat cushions shall be 3″ foam covered with heavy-duty seamless vinyl upholstery (Section

3.08 related).

5.04 LOWER WALL COVERING
The squad bench sides and lower portion of the streetside wall shall be nonporous, color- coordinated material.

5.05 GRAB RAIL(S)
One 75″L x 1.250″D stainless steel grab rail with three support brackets shall be securely mounted to roof structural framing running through centerline.

5.06 ACCESS DOOR GRAB RAILS
Each module access door shall have a 1.250″D L -style stainless steel grab handle which may also be used as an entry assist rail.

5.07 IV HANGER(S)
One retractable dual IV hanger with stabilizers shall be surface-mounted in the ceiling over the primary cot.

BraunNW (BLI) 23 of 35 Ford Type-3 Demo
5/8/24 3812-3

5.08C COT MOUNT
A Stryker #6390-700-001 floor plate shall be installed by BNW, to position the aft end of the cot 11″ forward of the rear doors (Section 8.02 related).

A 20 amp breaker and 10 ga. 12 VDC power and ground prewire shall be installed, running from the electrical cabinet to the frame rail, terminating in a 36″ capped and coiled pigtail forward of the rear axle.

To allow use of non -Power-LOAD, X-frame cots with the Power -LOAD system, a floor plate with plastic cover shall be provided and installed for mounting a customer-supplied- and-installed rear rail clamp.

5.10 ATTENDANT SEAT
A Wise #1655 rear-facing high-back bucket seat, upholstered with heavy grade vinyl, Dove gray, shall be located at the head of the cot position and pr ovide easy access to all action wall controls and outlets, and to the patient. Seat shall have a four-point seat belt and shall be securely anchored to a #1934 swivel base.

5.11 OXYGEN SYSTEM
The entire oxygen system shall be assembled with certified oxyg en hose (1000 PSI burst strength) with brass fittings, be pressure tested, and certified. A 50 PSI regulator shall be included, and one oxygen tank wrench shall be attached to the wall with hook -and-loop tape. A bulkhead connector shall be installed in the ceiling of Compartment #3.

Three Ohio-type outlets shall be installed:

1. One in Action Area #8

2. One on the curbside wall above the squad bench

3. One in ceiling above the primary patient

5.12 SUCTION PUMP
The unit shall have an electric pump as the source of suction, installed in Cabinet #13, and be vented to the outside of the vehicle under the module body. The pump shall be controlled by an on/off switch labeled ″SUCTION″ on the attendant panel in Action Area #8.

5.13 SUCTION COLLECTOR
A Rico model #RS4X-1001B suction regulator and wall-mount bracket with a 1200cc Rico disposable canister shall be installed in the Action Area #8.

5.14A SEAT BELT
Black DOT-compliant seat belts shall be installed at each seating position. Two black four- point, single-buckle energy-absorbing seat belts with below -the-bench retractors shall be installed on the squad bench for sit -up occupants. One four -point single-buckle energy absorbing seat belt with below -the-bench retractors shall be installed on the CPR seat.

Three additional automatic locking retractor seat belts with three lower seat belt buckle ends shall be set up for use with stretcher patients. The attendant seat shall have a four - point, single-buckle seat belt.

5.15 FLUID BARRIER
A formed stainless steel floor mounted fluid barrier which is 0.75″ high shall be provided between the module and cab. This barrier shall prevent fluids from running from the module floor into cab area.

BraunNW (BLI) 24 of 35 Ford Type-3 Demo
5/8/24 3812-3

5.16 INSULATION
The module side, ends, roof, doors, and floor shall be insulated to enhance the interior environment and to restrict heat, cold, and external noise from entering the module. The insulation shall be a non-settling foam plank material of 1.5″, or 0.75″ thickness depending upon location and available space.

Roof, doors, wall, and floor insulation shall be polyisocyanurate.

A 3″ wide, 60-mil, closed cell polyethylene foam tape shall be used as a thermal break on the inside surface of the wall tubes.

5.17 MODULE CLIMATE CONTROL SYSTEM
The module HVAC system shall i ncorporate a combination heating/air conditioning unit with 43,300 BTU/hr. heating and 32,000 BTU/hr. cooling capacity. The unit shall have a 580 CFM fan and controls independent of the cab system. A 12VDC booster pump shall be installed to optimize the heating capacity in the module. A return air path with open area equal to at least twice the blower outlet area shall be incorporated into the evaporator closeout.

The module system shall be controllable by a digital thermostat located on the streetside wall in the Action Area #8.

Four vents shall be installed in a vertical plenum on the aisle side of right front stack, spaced evenly.

A Beam #015715 metal wall port shall be installed in the vertical plenum to provide direct heat to a patient. A hose shall be shipped loose (Section 8.01 related).

5.18 EXTERNAL AIR INTAKE
To supplement heated or cooled air with fresh air, an external air intake shall be provided on the side of the module. The intake shall consist of an opening protected by an aluminum vent cover. The interior chamber of the intake shall be made of aluminum and be formed to prevent the collection of moisture. Washable filter media shall be installed in the intake chamber.

5.19 AIR RETURN
A return air path with an open area equal to at least twice the blower outlet area shall be incorporated into the evaporator closeout.

5.20 EXHAUST VENT
A motor-powered exhaust vent with a chrome Perko cover shall be located in the streetside rear corner of the module. A switch labeled ″VENT″ shall be installed in the Action Area attendant panel to turn on/off the exhaust vent (Section 6.13 related).

5.21 NO SMOKING/FASTEN SEAT BELTS SIGNS
Two ″NO SMOKING/OXYGEN EQUIPPEDʺ and ″FASTEN SEAT BELTS″ signs shall be installed - one set in the cab on the glove box door, and one set in the module above the Action Area oxygen outlet.

5.24 CLOCK
An atomic-controlled clock shall be installed on Cabinet #14 door. The clock shall be LCD display and show hours (12/24 selectable), min utes, seconds, date, day, and temperature.

Clock is powered by two AA alkaline batteries.

BraunNW (BLI) 25 of 35 Ford Type-3 Demo
5/8/24 3812-3

5.26 SHARPS/HAZARDOUS WASTE CONTAINER
One Becton Dickinson 8.2 qt. sharps container and one 7 qt. waste container shall be installed at the aft end of the Action Area #8 countertop, with a hinged clear polycarbonate cover with a finger hole.

A 5 Qt. Sage #85131 biohazard waste/sharps container and a 7 qt. waste container shall be installed on the curbside squad bench end bar (Section 5.34A related).

5.29 OXYGEN WINDOW
A 6″ x 11″ clear polycarbonate oxygen window with knob and self-closing hinges shall be installed.

5.34A BENCH RESTRAINT
A removable bar bench restraint shall be installed on the forward end of the curbside squad bench. The bar shall be 1.25″D satin stainless-steel tubing with 3″ radius bends. The upper removable bar section shall be 15″ across and 21″ high and have welded stainless steel brackets to hold a 5 Qt. Sage #8513 1 biohazard waste/sharps container and a 7 Qt. waste container (Section 5.26 related). One each shall be provided. The bar shall be mounted in

1.25″ satin finish stainless steel post bases attached to the front of the squad bench.

5.35A INTERIOR CYLINDER STORAGE
Tip-out latching storage for two customer -supplied-and-installed D -cylinders shall be provided in Cabinet # 11, with a wedge -shaped stainless-steel spring to prevent cylinder rattling.

BraunNW (BLI) 26 of 35 Ford Type-3 Demo
5/8/24 3812-3
6 ELECTRICAL
All added body and chassis electrical equipment shall be served by circuits separate and distinct from the vehicle chassis circuits. All vehicle wiring shall be copper and conform to all SAE J1128 requirements. The wiring shall be colored, numbered, or function coded every 3″ for permanent identification and correspond with the vehicle schematics.

Solderless, insulated connectors shall be used. Slotted Panduit -style wiring duct shall be used in electrical component module to ensure air circulation throughout power component wiring. The wiring shall be routed in conduit or looms and wiring shall be secured to the underbody or frame with insulated metal cable straps. All power distribution cabling shall be covered with a protective split loom. Where wiring passes over the exhaust, a heat shield shall be installed. The electrical component module shall be equipped with positive locking plugs to provide easy disconnect for remount or repair of body. All wiring devices, switches, outlets, etc., except circuit breakers, shall be rated to carry 125% of the maximum ampere load for which the circuit is protected.

The vehicle electrical system shall be tested and certified to AMD 005 requirements.

6.01 ELECTRICAL LOAD DEVICES
Body electrical wiring shall utilize overload protective devices of the automotive -type circuit breaker. In addition, one single pole, 20-amp circuit breaker shall be provided for future use. The circuit breakers, relays, and other electrical devices shall be included as part of the enclosed electrical component module located in Cabinet #14.

6.02 VOLTMETER/AMMETER
A single display voltmeter/ammeter shall be installed on the side of the console, driver's side, which simultaneously displays voltage and alternator current when the ignition is on.

Display flashes to indicate low voltage.

A buzzer shall indicate low voltage.

6.04 IGNITION CONTROL
Chassis electrical circuits shall be controlled by the ignition switch as provided by the OEM chassis manufacturer. The auxiliary chassis-related functions shall be powered by one 100- amp continuous duty solenoid, triggered by the chassis ignition.

6.05B MODULE POWER
Module power shall be controlled by a driver's console -mounted switch labeled ″MODULE DISC.″ which activates an InPower #SSC42-275 solid state contactor (Section

6.09 related). An ignition interlock shall disconnect module power 15 minutes after the vehicle's ignition is turned off. The interlock shall also allow module power to be reactivated independently for 15 minutes by cycling the ignition switch. The SSC42 -275 shall turn off module power without delay when the module disconne ct switch is turned off.

6.06 WIRING ACCESS
All cabinets and compartments shall have removable panels as needed to access wiring harnesses and hoses.

BraunNW (BLI) 27 of 35 Ford Type-3 Demo
5/8/24 3812-3

6.07 BACK-UP ALARM
An SAE J994-compliant self-adjusting back-up alarm shall be installed, without a disable switch.

6.08 SERVICE LOOP
A 6″ service loop of wire or harness shall be provided at all electrical components, terminals, and connection points.

6.09 DRIVER'S CONSOLE
A driver's console made of black -powder-coated formed aluminum shall be installed between the seats. It shall have a switch panel with the following layout, two cup holders, two armrests and a map holder with six mill-finished aluminum dividers.

1. Passage
Compt.

D/O
Lights

2. 3.

Siren Module
Disc.

Emerg.

Master Blank

4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14.

Blank White
Lights Blank
Blank
(Opticom
Circuit)
Blank Blank Spare Left
Scene
Right
Scene
Rear
Scene
USB
A/C

6.10 SWITCHES
Switches installed in the driver's console and attendant panel(s) shall be rocker -type and permanently marked by function.

BraunNW (BLI) 28 of 35 Ford Type-3 Demo
5/8/24 3812-3

6.12 DOOR AJAR WARNING LIGHT
A flashing LED light with a red lens shall warn the driver of an open module passage door, and a flashing LED light with an amber lens shall warn the driver of an open module compartment door. The lights shall flash only if the ignition is on. Lights shall be installed on the driver's console (Section 6.09 related).

6.13 ATTENDANT CONTROL PANEL
A six-switch attendant control panel shall be located on the streetside wall in the Action Area #8 with the following switch layout:

1. 2. 3. 4. 5. 6.

Left Dome
Hi-Lo-Off
Right Dome
Hi-Lo-Off Suction Vent Attendant
Light USB A/C

A digital thermostat and an inverter status panel shall be located adjacent to the attendant control panel (Sections 5.17 and 6.31 related).

6.14 CABINET LIGHTING
The wall area below Cabinets #1, and #4 shall be lighted utilizing under-cabinet LED strip lighting with an ON/OFF switch labeled ″ATTENDANT LIGHT″ in the attendant panel Section 6.13 related).

6.15A STEP LIGHT
A Whelen #3SC0CDCR Clear Lens Clear 3″ LED light shall be installed on the forward wall of the curbside door stepwell.

6.16B MODULE INTERIOR LIGHTING
Shall be designed to maintain maximum headroom without interfering with the structural integrity of the roof. Module interior lighting shall consist of six Whelen #80C0EHCR dual intensity LED recessed lights:
- One bank of three lights positioned toward the streetside - One bank of three lights positioned toward the curbside There shall be a control switch for each bank of dome lights in the streetside attendant panel (Section 6.13 related). Dome light switches shall be momentary contact HI-LO-OFF switches labeled ″LEFT DOME″ and ″RIGHT DOME″.

Pressing the top of the switches shall increase intensity. Pressing the bottom of the switches shall decrease intensity.

The curbside bank of lights shall be automatically activated when the rear or side doors are opened or by a momentary rocker switch labeled ″DOME TIMER″ mounted on the wall near the curbside passage door, which shall activate a battery hot timer. Pressing the switch once shall initiate 15-minute timed operation of the lights. Pressing the switch again shall cancel the timed operation.

BraunNW (BLI) 29 of 35 Ford Type-3 Demo
5/8/24 3812-3

6.17 BASIC EXTERIOR LIGHTING
Basic lighting shall include headlights, parking lights, directional signal lights, tail and stop lights, license plate light, back -up lights, hazard lights, identification lights, clearance lights, and side marker lights as required by FMVSS 108.

Module identification lights, clearance lights, and side marker lights, unless included on a lightbar, shall be Truck-Lite LED Model 36.

Rear and side reflex reflectors shall be installed in accordance with FMVSS 108 requirements.

Rear stop/tail, turn and back -up lights shall be Truck -Lite Model 45 series LED lights, installed in the rear kick panel, pattern from outboard in: red stop/tail light, amber turn signal, and clear back -up light. The back -up lights shall activate automatically when the vehicle is placed in reverse.

6.19 ANTENNA MOUNTS AND CABLES
Two NMO universal antenna mounts with KHFUD/RG58UD cables, Larsen HyPermaster universal connectors and mini-UHF adapters shall be installed on the module roof. Antenna base access shall be through the dome light openings, and the cables shall terminate in the electronics cabinet #16.

6.20 BLOCK HEATER
A block heater, with circuit breaker in the 120VAC Power Box, shall be wired to the 120VAC shorepower system (Section 1.01.02 related).

6.21 120VAC/SHORELINE CIRCUIT BOX
Utility power shall be furnished from 120VAC shorepower via a Kussmaul 20-amp Super Auto-Eject plug with a white cover on a stainless steel plate with a green indicator light located on the driver's side of vehicle and distributed via a formed aluminum pow er box recessed into the streetside front compartment. 120VAC power box shall be recessed and shall have an easily removable cover.

Circuit breakers shall be installed for overcurrent protection and circuit isolation:
• Block Heater (15 A)
• Inverter (20 A)
• Receptacles (15 A)
All exposed receptacles shall be ground fault circuit interrupting (GFCI) and shall have a power on indicating light.

Five interior 120VAC GFCI duplex receptacles shall be mounted:
• One in Compartment #1
• One in Cabinet #1
• One in Cabinet #5
• One in Action Area #8
• One in Cabinet #19

6.22 BATTERY GROUNDS
In addition to OEM chassis grounds, the following ground circuits shall be added to reduce RF interference:
-A minimum 4 ga. ground cable from the power component panel to the chassis frame. -Two braided ground straps with soldered ends from the module body to the chassis frame.

BraunNW (BLI) 30 of 35 Ford Type-3 Demo
5/8/24 3812-3

6.23 BATTERY CHARGER
A 60-amp battery charger shall be provided as part of the Samlex Pure Sine 1200 -watt inverter system. (Section 6.31 related)

6.24A BATTERY MODIFICATIONS
The two OEM batteries shall be relocated to the curbside forward exterior compartment on a 300 lb battery tray with a locking right slide . The batteries shall be inte rconnected to provide maximum cold cranking amps and reserve capacity at all times.

6.25 12VDC POWER SUPPLY
Two 12VDC, 15-amp lighter-style power point receptacles shall be provided; – One Action Area #8
– One Cabinet #19
Two Kussmaul USB A/C dual charge ports shall be installed:
– One in Action Area #8
– One in the driver’s console
All 12VDC power point receptacles, USB charge ports, 12VDC charging circuits, electric air compressors, and cool cabinets, if present, shall be powered from a 12VDC auxiliar y bus. An InPower LVD20-100-SPC540 low voltage disconnect switch shall deliver power to the auxiliary bus only when the supply voltage to the vehicle batteries is at or above 13.0 VDC.

6.26 COMPARTMENT LIGHTING
LED strip lighting shall be installed in eac h outside compartment, and shall be activated by the respective compartment door switch.

6.27 EXTERIOR DOOR SWITCHES
Shall be 1/2″ mechanical door switches.

BraunNW (BLI) 31 of 35 Ford Type-3 Demo
5/8/24 3812-3

6.30 EMERGENCY WARNING SYSTEMS
All emergency lighting shall be controlled by the "EMERG. MASTER" switch on the driver's console (Section 6.09 related). When the switch is on, module power is on, and the vehicle is not in park, all emergency lighting shall be activated, and the hands-free function of the siren shall be enabled. The white lights shall be disabled when the vehicle is shifted into park.

6.30.01 FRONT LIGHTBAR
A 94″ Whelen 4500 Plus Series LED lightbar shall be recessed on the front of the module, pattern curbside to streetside:

Location Lens
Color Model Light
Color Type Light Flash
Pattern Additional
Curbside
Clear 700
Series Red LED Flasher A/F
150
Clear 700
Series Red LED Flasher A/F
150
Clear 700
Series Red LED Flasher A/F
150
Clear 700
Series Clear LED Flasher A/F
150
Center Clear Blank Clear Opticom
Circuit
Streetside
Clear 700
Series Clear LED Flasher A/F
150
Clear 700
Series Red LED Flasher A/F
150
Clear 700
Series Red LED Flasher A/F
150
Clear 700
Series Red LED Flasher A/F
150
The lightbar shall be recess-mounted with the horizontal plane of the roof, and protrude no more than 1/2″ beyond the vertical plane of the front and sides of the module. The LED ICC clearance and identification lamps shall be an integral part of the lightbar.

The rear lightbar shall be controlled by the "EMERG. MASTER" switch in the driver's console. The white flashers shall be disabled when the vehicle is shifted into park.

The white lights shall also be controlled by the ʺWHITE LIGHTSʺ switch in the driver's console.

BraunNW (BLI) 32 of 35 Ford Type-3 Demo
5/8/24 3812-3

6.30.02 REAR LIGHTBAR
A 94″ Whelen 4500 Plus Series LED lightbar shall be recessed on the rear of the module, pattern curbside to streetside:

Location Lens
Color Model Light
Color Type Light Flash
Pattern Additional
Curbside
Clear 700
Series Red LED Flasher A/F
150
Clear 700
Series Red LED Flasher A/F
150
Clear Triple
LR11 Clear LED Load
Light None
(Section

6.30.04 Related)
Clear 700
Series Amber LED Flasher A/F
150
Center Clear 70BTT Red LED BTT Third
Brake
Light
Streetside
Clear 700
Series Amber LED Flasher A/F
150
Clear Triple
LR11 Clear LED Load
Light None
(Section

6.30.04 Related)
Clear 700
Series Red LED Flasher A/F
150
Clear 700
Series Red LED Flasher A/F
150
The lightbar shall be recess-mounted with the horizontal plane of the roof, and protrude no more than 1/2″ beyond the vertical plane of the rear and sides of the module. The bar shall include an LED brake/clearance light over the center lights, and LED clearance lights shall be an integral part of the lightbar.

The rear lightbar shall be controlled by the “EMERG. MASTER” switch in the driver's console.

6.30.03 FLASHERS
Four Whelen #M9RC Clear Lens Red Super-LED flashers shall be mounted two each on the curbside and street side of the module in upper corners.

Two Whelen #M9AC Clear Lens Amber Super-LED flashers shall be mounted on the rear of the vehicle in line with the rear entrance door windows.

Lights shall be controlled by the “EMERG. M ASTER” switch on the driver's console (Section 6.09 related).

Two Whelen #WIONSMCR Clear Lens Red flashers with chrome housings shall be installed on the rear of the module lower , one streetside, and one curbside just above the rear kick panel. Lights shall be controlled by the ″EMERG. MASTER″ switch on the driver's console (Section 6.09 related).

BraunNW (BLI) 33 of 35 Ford Type-3 Demo
5/8/24 3812-3

6.30.04 SCENELIGHTS
Four Whelen #M9LZC Scene Super-LED light heads shall be mounted, two each on the curbside and streetside of the module in upper corners.

The curbside passage door shall activate the curbside scene lights. The scene lights shall also be controlled by the respective switches on the driver's console (Section 6.09 related).

Two Whelen LR-11 LED scene lights shall be included in the rear lightbar. The rear scene lights shall be controlled by the “REAR SCENE” switch on the driver's console (Section

6.09 related), and shall activate when the rear curbside passage door is opened or when the vehicle is placed in reverse.

6.30.05 SPOTLIGHT
A Golight #20204 roof-mounted LED spotlight with white housing and a stainless -steel mounting bracket shall be installed on the center of the cab roof . A hard-wired controller shall be mounted on the OEM coin holder slot on the cab dash.

6.30.06 INTERSECTION LIGHTS
Four Whelen #WIONSMCR Clear Lens Red LED flashers with chrome housings shall be installed, one on each cab fender and one above each module wheel well. Lights shall be controlled by the “EMERG. MASTER ” switch on the driver's console (Section 6.09 related).

6.30.08 GRILLE LIGHTS
Two Whelen #WIONSMCR Clear Lens Red LED flashers with chrome housings shall be installed on the OEM grille. Lights shall be controlled by the “EMERG. MASTER” switch on the driver's console (Section 6.09 related).

A pre-wire shall be provided from the electrical panel to the grille area for future use of White Lights as wig wags.

A pre-wire shall be provided from the electrical panel to the grille area for future use of a grille light as steady red.

6.30.09 SIREN
A Whelen 295SLSA1, 200-watt siren shall be installed in the driver's console (Section 6.09 related). Standard features shall include Radio Rebroadcast, Public Address, Manual, Wail, Yelp, Air horn, and Piercer tones. The siren’s hands-free function shall operate through the OEM horn ring circuit when the sirens rotary selector is in the HF position and the Emergency Master switch is on.

6.30.10 SIREN SPEAKERS
Two Federal Signal Dynamax #ES100C 100 watt speakers with North Star stainless steel grilles shall be installed in the OEM bumper.

6.31 INVERTER
A Samlex Pure Sine 1200-watt inverter with a 60-amp battery charger shall be installed in Cabinet #15. A remote inverter status panel shall be installed in the Action Area #6. The inverter shall be configured to turn on and off with ignition.

6.35 FLUID WARMER
A 120VAC fluid warmer with a 120VAC GFCI duplex receptacle shall be installed in cabinet #1. The warmer shall be thermostatically controlled at 95 to 115 degrees F. Space for 10 one-liter bags of fluids shall be provided with a 4” surround to contain the fluid bags.

BraunNW (BLI) 34 of 35 Ford Type-3 Demo
5/8/24 3812-3

6.40 ELECTRIC DOOR LOCKS
Electric door locks shall be installed on all compartment and module passage doors. Two lock/unlock switches shall be provided in the module: one located on the rear curbside passage door, and one located on the curbside passage door. The door locks for the cab and module shall be interconnected, to allow all doors to be locked/unlocked from either the cab or module.

A hidden unlock switch shall be installed behind the license plate on the rear of the module (Section 4.16 related).

6.46 AUDIO/VIDEO/RECORDING EQUIPMENT
Item #1
Description: A Zorg back-up camera system shall be installed, including a surface - mounted camera and a rear-view mirror/monitor with a 4.3″ screen.

Location: Camera on the rear of the module, centered above the rear passage doors.

Rearview mirror/monitor centered on chassis windshield, upper.

Additional Instructions: Camera shall automatically display on monitor when the vehicle is placed in reverse. The programming remote shall be shipped loose (Section 8.01 related).

6.48 TRAFFIC SIGNAL PREEMPTION
A circuit shall be installed for future installation of a traffic preemption emitter (Opticom) in the front light bar. The Opticom circuit shall be set up to be controlled by a future switch on the driver's console and shall be disabled when the vehicle is shifted into park.

BraunNW (BLI) 35 of 35 Ford Type-3 Demo
5/8/24 3812-3
7 SUPPORTING DOCUMENTATION

7.01 OWNERS MANUAL
Shall be provided with vehicle and consists of the following items:

1. Braun Northwest Contact Information

2. Table of Contents

3. Manufacturers’ Labels

4. Electrical Load Test/Payload/Paint Stickers

5. Braun Northwest Warranties
Lifetime module warranty
Seven-year/75,000-mile limited electrical warranty
Two-year/30,000-mile conversion warranty
Five-year paint warranty
Chemical De-Icer Statement

6. Service and Operations manual

7. Electrical
Wire charts and plug pinouts
Harness layout
Schematics

8. Parts list

9. Paint information

10. Products and Information

11. Second OEM chassis key

8 MISCELLANEOUS EQUIPMENT

8.01 LOOSE EQUIPMENT
The following equipment shall be shipped loose with the vehicle:

1. Touch Up Paint
• White (GLV-11291704)
• White G2-33631 Alt 2
• Gray GLV-51748

1. Spare tire and wheel

2. Antenna Coax Ends

3. Adjustable shelf for compartment #1

4. Road Safety Kit (includes flares, triangle and fire extinguisher) (For BNW Demo period)

5. 12.5'L hose

* * * * * *

BraunNW (BLI) 1 of 36 Ford Type-3 Demo
4/9/24 3878-3
BRAUN NORTHWEST, INC.

DETAILED SPECIFICATIONS
FOR

DEMONSTRATOR
E450, GAS, 167” MODULE, TYPE 3

COLOR/RED
VEHICLE #3878-3
1 CHASSIS

1.01 OEM CHASSIS
• 2024 Ford E-450, meeting all the specifications of Section 1.01. (Chassis subject to model year changes)
– 3 year/36,000 mile ″Bumper to Bumper″ warranty
– 5 year/60,000 mile Powertrain warranty
– Ambulance Prep. Package 47H
– Dual rear wheels
– Twelve Frame Pucks (559)
– Provided by Braun Northwest

1.01.02 POWER TRAIN
• Engine – Gasoline
– 7.3L V8 Premium (99N)
– Engine block heater
– Heavy duty dry type air cleaner with flow restriction indicator • Engine Cooling System
• Heavy duty, closed-air, free-liquid state type
• Coolant recovery system
• 50/50 solution Permanent type antifreeze to –40 degrees F • Transmission

BraunNW (BLI) 2 of 36 Ford Type-3 Demo
4/9/24 3878-3
– 6-speed automatic transmission with tow/haul mode
– Auxiliary transmission oil cooler
• Exhaust System
– System complies with Federal Motor Carrier Safety Regulations, Part 393.83 – Suspended using three hangers, excluding manifold attachment – Discharge at right rear side of module
– Tailpipe shall not terminate within twelve inches of the vertical axis of the fuel tank filler opening.
– Two exhaust heat shields mounted in mid -chassis, right -hand side for upfitter installed frame pucks

1.01.03 STEERING
• Power assisted
• Tilt and telescoping steering wheel

1.01.04 SHOCK ABSORBERS/STABILIZER BARS
• Heavy-duty shock absorbers front and rear
• OEM front and rear stabilizer bars

1.01.05 BRAKES
• Four Wheel Disc with Traction Control
– Hill Start Assist
– Traction Control
– Electronic Stability Control

1.01.06 TIRES AND WHEELS
• Seven OEM LT225/75R16E all-season steel belted radials • Seven OEM 16″ painted white steel wheels
• Spare tire and wheel
• Steel valve stems

1.01.07X ELECTRICAL
• Alternators – OEM dual heavy-duty, 397 amps total (63N) • Batteries – OEM dual heavy-duty, 78 amp-HR batteries

1.01.09 CAB EXTERIOR

BraunNW (BLI) 3 of 36 Ford Type-3 Demo
4/9/24 3878-3
• Exterior Upgrade Package
– Bumper – Front, Chrome
– Grille – Chrome
• License Plate Bracket
• Horn – OEM dual electric
• Windshield wipers – Interval
• Telescopic Trailer Tow Mirrors with manual adjustments – Two black, below eye level, manually telescoping trailer tow – Power adjusted upper glass
• Lights
– Headlamps with Autolamp
– Dual sealed-beam with fixed lens
– Daytime Running Lamps, configurable
• Fuel tank – OEM 55 Gallons

1.01.11 COLORS
• Exterior – Race Red (PQ)
• Interior – Medium Flint Gray

BraunNW (BLI) 4 of 36 Ford Type-3 Demo
4/9/24 3878-3

1.02 CHASSIS MODIFICATIONS
The following modifications will be made to the chassis by Braun Northwest.

1.02.03 VALVE EXTENDERS
Stainless steel wheel simulators shall be installed on all outer wheels, with braided valve stem extenders on all four rear wheels.

Heat shields shall be bolted to chassis frame and extend from back of cab to the frame cross member just behind the rear axle.

1.02.05 RUNNING BOARDS
Running boards made of 0.125″ bright aluminum diamond plate with front splash guards shall be installed on both sides of the cab, flared towards the front corners of the module, and securely mounted with stainless steel 1/4″-20 truss head bolts.

1.02.07 AUTO THROTTLE
An Intermotive voltage monitor shall be installed to automatically adjust the auto throttle for changes in electrical load and AC loads.

1.02.09 MUD FLAPS
Mud flaps with the ″NORTH STAR″ logo shall be installed behind each rear wheel.

BraunNW (BLI) 5 of 36 Ford Type-3 Demo
4/9/24 3878-3

1.03 MODULE-TO-CHASSIS MOUNTING SYSTEM

1.03.01 MODULE MOUNTING SYSTEM
Module mounting system shall be designed and used as supplied by chassis manufacturer.

It shall consist of twelve rubber puck mounts secured with chassis manufacturer -supplied

0.50″ hardened bolts.

1.03.03 CAB-TO-MODULE GASKET
A closed-cell, neoprene, weatherproof gasket shall be installed between the cab and module to minimize electrolytic corrosion.

BraunNW (BLI) 6 of 36 Ford Type-3 Demo
4/9/24 3878-3
2 MODULAR CONSTRUCTION
All material utilized shall be of the corr ect type, alloy, and thickness to withstand the intended usage and provide protection against cracking, corrosion, or metal fatigue. All materials utilized shall be of open stock origin, commonly available through local sources, for rapid and economical repair or modification of the body. Any use of proprietary parts or materials in the construction of the body is unacceptable, due to potential delays or difficulties in future repairs or service. NO EXCEPTIONS TO BE TAKEN IN THIS AREA. This specification ha s been designed and written to fill specific needs of this agency. Where brand name, make, or model of equipment has been specified, no exceptions shall be allowed. Where compartment and cabinet sizes have been specified, bidder must bid substantially (plus or minus 1″) the size specified.

The module shall have a transferable lifetime structural warranty.

2.01 MATERIAL

FORMED SHEETING SIZE ALLOY
Skin/Roof/Compartments/Subfloors/Doors 0.125ʺ 5052-H32
Interior Cabinets 0.090ʺ 5052-H32
Diamond Plate 0.125ʺ/0.08ʺ 3003-H22
Stainless Steel 16 ga., 20 ga 304 # 4B

BraunNW (BLI) 7 of 36 Ford Type-3 Demo
4/9/24 3878-3

2.03 STRUCTURAL FRAMING
Side wall and rear wall construction shall consist of 2″ x 2″ x 0.125″ aluminum square tubing extensions welded together with a maximum of 14″ centers. 1″ x 2″ x 0.125″ aluminum tubing may be utilized in addition to 2″ x 2″ tubing to accommodate custom compartment sizes. The bottom of the wall structure shall be sealed with a welded 2″ x 2″ tube, a 2″ x 2″ angle, or a 0.125″ plate depending upon location. The wall structure shall be capped with a 2″ x 4″ x 0.125″ header upon which a 2″ x 2″ x 0.125″ roof structure is welded. This process provides a unitized roll cage structure for greater occupant safety.

The front wall structure shall be constructed of formed aluminum channels to allow ample space for wiring raceways, heater hoses, and A/C hoses.

0.25″ x 1.5″ aluminum stringers shall span longitudinally between the laterals.

2.05 MODULE SEAMS
All body and compartment seams at or below floor level shall be full -seam-welded. The entire perimeter of the subfloor shall be completely sealed with a caulking material, creating a watertight seam.

2.06 EXTERIOR SKIN
A Norton NORBOND closed-cell, polyurethane foam tape with high-performance acrylic adhesive shall be utilized full length on all front and rear wall and roof frame members. A polyurethane adhesive sealant shall be applied to the edges of framing members that are bonded wit h NORBOND tape. An advanced two -part methacrylate structural adhesive shall be used to bond all side wall tubes to the exterior skin and door frames.

The module shall be constructed utilizing full -size sheet construction to minimize body seams. There shall be no corner or mid-body seams.

2.07 MODULE ROOF
In order to improve module strength and minimize exposed seams, the roof shall be seamed transversely, shall be crowned, shall have a 1.5″ radius along the edges, and shall be welded to 2″ x 4″ wall heade r tubes 4.75″ below the roof line. The roof shall be supported by positive contact between sidewall framing and roof framing. All seams on the roof surface shall be continuously welded and body -worked on the outside. In order to avoid the possibility of pa int and/or weld cracking, no extrusions shall be used in the exterior construction of the roof or corners of the module.

The module roof front and rear edges shall be constructed to allow mounting of recessed lightbars.

BraunNW (BLI) 8 of 36 Ford Type-3 Demo
4/9/24 3878-3

Door(s) – Double
Light(s) – One vertical LED strip light
Additional Instructions –

1. The 120VAC Power Box shall be installed in the forward wall (Section 6.21 related), recessed so as not to protrude into the compartment.

3. Two vertical strips of heavy-duty aluminum track shall be added to each of the side walls for future installation of a full-length shelf to be shipped loose (Section 8.01 related).

4. A spare tire mount shall be mounted on the back wall of the aft section (Section

4.19 related).

5. A 120VAC GFCI duplex receptacle shall be i nstalled on the forward wall, lower (Section 6.21 related).

6. A vent with MERV 8 polyester filter media and a hex -punched stainless -steel cover shall be installed on the forward wall.

1. Two heavy-duty aluminum tracks will be installed on back wall to accommodate a bin-type shelf.

2. A slide-out tool board with 20″ slides, grab hole, gas shock, bracket and strap shall be installed by BNW in Compartment #2 for storage of a customer-supplied-and- installed Stryker stair chair.

3. Shall have a spring hanger close out located in forward back corner of the compartment that allows for leaf spring travel.

4. Two vents with MERV 8 polyester filter media and a hex-punched stainless-steel cover shall be installed one each on the forward and aft wall.

BraunNW (BLI) 9 of 36 Ford Type-3 Demo
4/9/24 3878-3
COMPARTMENT #3
Interior Dimensions – 22”W x 77”H x 20D
Doorway Dimensions – 22”W x 70”H
Location – Curbside, rear
Shelving – One 13.5” bin type shelf
Door(s) – Single
Light(s) – One vertical LED strip light
Additional Instructions –

1. This compartment shall have a welded bracket, painted to match the compartment, and three ratcheting straps with UHMW stiffeners set up for storage of a customer- supplied-and-installed H or M-size cylinder (Section 4.10 related).

2. Two backboard restraining straps shall be installed on the aft wall. A formed stainless-steel gasket cover shall be installed so that backboards do not cut gasket material.

3. A vent with MERV 8 polyester filter media and a hex -punched stainless -steel cover shall be installed on the aft wall.

1. Shall have a spring hanger close out located in the back of the compartment that allows for leaf spring travel.

1. This compartment shall provide inside/outside access to Cabinet # 19 with a full width stainless steel threshold on the floor level shelf.

6.24 related).

2.09 MODULE DOORS
The doors shall be box-pan-formed with a total thickness of 2″.

2.09.01 DOOR FRAMES AND SEALS
Each door frame shall have a flange for the installation of an air cell hollow core 360 - degree compression door seal. This seal creates watertight, dust -free compartment integrity. Door seal shall be knock -on type. Door frames shall be bonded to the adjace nt tubes such that no exterior flange is required.

BraunNW (BLI) 10 of 36 Ford Type-3 Demo
4/9/24 3878-3

BraunNW (BLI) 11 of 36 Ford Type-3 Demo
4/9/24 3878-3

2.09.03 DOOR LATCHES
Exterior door handles shall be semi -flush, chrome -plated Eberhard E Grabber #21100.

Passage doors shall have release handles on the inside of each door. All exterior doors shall have rotary latches and striker posts that meet FMVSS 206 requirements. Striker posts shall be adjustable and be secured with a nut from behind the door frame. The striker washer shall not be removed. Doors greater than 45″ tall shall have double rotary latches activated by stainless steel rods. Once final adjustments have been made, threads shall have Loctite or equivalent applied. All double -door compartments shall have an exterior E Grabber handle and rotary latches on each door. Doors shall latch to doorframe -mounted striker posts only and not to one another. Curbside passage and rea r curbside doors shall have interior handles with dual-point, rod-actuated, rotary latch systems that are lockable inside and out. All locks shall be keyed J236.

The side and rear passage doors shall all have emergency release levers, one at the top and bottom of each door and accessible from the inside of the module.

A grabber-type hold -open device with replaceable rubber catch shall be installed on Compartment #3.

Two 2″ black seatbelt-style straps with footman loops shall be installed, one each at the top and bottom of the door frame, to protect the door from excessive overtravel.

2.09.06 REAR DOOR CONTROL
Rear door controls shall be one grabber -type hold-open device with replaceable rubber catch, per door.

Red/white 1.5″ conspicuity tape shall be installed on the outboard vertical edge of each door.

BraunNW (BLI) 12 of 36 Ford Type-3 Demo
4/9/24 3878-3

2.09.10 THRESHOLDS
All compartment and module access door frames shall have full -width-formed stainless- steel threshold plates to protect the lower edge of frame.

1. Cabinet shall be divided in the center by a vertical fixed divider.

2. An IV Warmer with a 4” surround shall be located in the lower aft corner of this cabinet (Section 6.35 related).

3. One 120VAC GFCI duplex receptacle shall be installed on the back wall of the cabinet (Section 6.21 related).

CABINET #2
Dimensions – 43.5”W x 7”H x 15.75”D
Location – Streetside above CPR seat
Shelving – None
Door(s) – Sliding clear 0.25 ” polycarbonate with felt -lined anodized alumin um track, interlocking aluminum trim, and full extruded aluminum door pulls with integral door latch.

Lighting – None
Additional Instructions – None

BraunNW (BLI) 13 of 36 Ford Type-3 Demo
4/9/24 3878-3
CABINET #3
Dimensions – 26”W x 13.25”H x 15.75”D
Location – Streetside upper rear
Shelving – One adjustable
Door(s) – Sliding clear 0.25 ” polycarbonate with felt -lined anodized aluminum track, interlocking aluminum trim, and full extruded aluminum door pulls with integral door latch.

Additional Instructions – None

Lighting – LED under-cabinet strip light (Section 6.14 related) Additional Instructions – None

CABINET #5
Dimensions – 27”W x 15”H x 20”D
Location – Streetside, open area aft of CPR seat
Shelving – None
Door(s) – None
Additional Instructions –

1. A 120VAC GFCI duplex receptacle shall be located in the lower left area of the back wall (Section 6.21 related).

2. A full depth one -piece 16-gauge, 304 stainless steel countertop with a 0.5″ aluminum retaining lip and aluminum cove trim along the wall shall be installed.

Additional Instructions – None

BraunNW (BLI) 14 of 36 Ford Type-3 Demo
4/9/24 3878-3
CABINET #7 – CPR Seat with Storage
Dimensions – Bench: 26”W x 18.75”H x 20”D
Storage: 26”W x 7.625”H x 20”D
Location – Streetside aft of Action Area
Shelving – None
Door(s) – Hinged aluminum bench lid, with removable high-density foam padding covered with seamless vinyl shall provide access to the storage area. It shall have a 1.5” overhang, an automatic hold-open device, and stainless steel paddle latch.

Additional Instructions –

1. A 4 -point, single -buckle seat belt with below -the-bench retractors shall be installed.

2. The CPR 4-point seat back and/or head pads shall have high-density foam padding covered with seamless vinyl.

3. The CPR seat base to be formed from aluminum and securely anchored to sub - floor. The bottom and unfinished sides of the storage area shall be sprayed with textured polyurea and painted white with gray splatter.

CABINET #8 – Action Area
Dimensions – 59.125”W x 28.75”H x 20”D
Location – Streetside forward of CPR seat
Shelving – None
Door(s) – None
Additional Instructions –

2. One Becton Dickinson 8.2 qt. sharps container and one 7 qt. waste container shall be installed at the aft end of the Action Area countertop, with a hinged clear polycarbonate cover with a finger hole.

3. A full depth one -piece 16 gaug e, 304 stainless steel countertop with a 0.5″ aluminum retaining lip and aluminum cove trim along the wall shall be installed.

Additional Instructions – None

BraunNW (BLI) 15 of 36 Ford Type-3 Demo
4/9/24 3878-3
CABINET #10
Dimensions – 36.75”W x 7”H x 9”D
Location – Curbside upper forward
Shelving – None
Door(s) – Sliding clear 0.25 ” polycarbonate with felt -lined anodized aluminum track, interlocking aluminum trim, and full extruded aluminum door pulls with integral door latch.

Additional Instructions – None

The forward lid shall provide access to the storage area. The aft lid shall be fixed. The pad shall be removable.

Additional Instructions –

1. The squad bench back and head pad shall have high-density foam padding covered with seamless vinyl. Two four-point single-click seat belts with below-the-bench retractors shall be installed. Three two-point automatic locking retractor seat belts shall be installed on the bench with three additional lower receivers, set up for stretcher patients.

2. The squad bench base to be formed from aluminum and securely anchored to sub- floor. The bottom and unfinished sides of the storage area shall be sprayed with textured gray polyurethane and painted white with gray splatter.

3. An Oxygen window shall be installed in the forward-facing wall at the aft end of the bench.

4. An Oxygen outlet and a momentary rocker switch to activate the dome timer shall be installed on the curbside wall over the bench (Section 6.16 related).

5. A bench end restraint bar shall be installed on the forward end of the squad bench (Section 5.34 related).

BraunNW (BLI) 16 of 36 Ford Type-3 Demo
4/9/24 3878-3
CABINET #13 – HVAC
Dimensions – 34.75”W x 14.5”H x 27.875”D
Location – Front, right upper
Shelving – None
Door(s) – None
Additional Instructions –
• This cabinet shall house the heater/AC unit and the suction pump (Section 5.12 & 5.17 related).

Additional Instructions –

1. This cabinet shall house the electrical component module. An atomic -controlled clock shall be installed on the face of this cabinet (Section 5.24 related).

CABINET #15
Dimensions – 18.75”W x 25”H x 10”D
Location – Front, forward of action area
Shelving – Two adjustable shelves
Door(s) – None
Additional Instructions – None

2. The inverter shall be installed in this cabinet, on the back wall, lower (Section 6.31 related).

BraunNW (BLI) 17 of 36 Ford Type-3 Demo
4/9/24 3878-3
CABINET #18 – Drawer
Location – Front, right below Cabinet #17
Additional Instructions –

1. There shall be one 23”W x 5 ”H x 19 ”D metal drawer. Drawer shall operate on slides rated at 300 lb. per set and have a gas shock hold open/closed device and non-locking paddle slam latch to ensure drawer does not accidentally open or close during operation of the vehicle. Drawer shall be of formed 0.125 ” aluminum construction, painted to match the interior. Drawer shall have machine -stamped divider supports along the front and back with four removable ABS dividers.

Door(s) – Two clear 0.375″ polycarbonate side-hinged doors with paddle latches. Each door shall have two 20 ga stainless steel braces, 0.375″D steel rods, and slam latches rated for 750 lb. each.

Additional Instructions –
– This cabinet shall be accessible from the outside via exterior Compartment #5.

2. One 120VAC GFCI duplex receptacle and one 12VDC receptacle shall be installed in the upper forward portion of the forward wall (Section 6.21 & 6.25 related).

3. The HVAC shall be distributed thru a vertical plenum on the aisle side of the right front stack.

Aluminum diamond plate kick panel shall be installed on the sides and face of the doorstep.

2.12 FRONT MODULE WALL RECESS
Shall be recessed 8″ into the module body to provide for maximum adjustment of cab seats.

2.13A CAB TO MODULE PASSAGE
Shall be a walk-thru measuring 18.25″W x 48″H.

2.14 WHEEL WELL LINERS
Wheel well liners made of formed aluminum shall be installed in the module wheel well openings.

2.15 ELECTROLYSIS PREVENTION
All external materials and fasteners shall be selected to prevent electrolysis and corrosion due to dissimilar materials and exposure to the elements. The module shall be painted before any exterior items (hinges, latches, door hold opens, etc.) are installed to provide an isolating film between dissimilar materials. Exterior fasteners used for direct connection to painted aluminum surfaces shall be coated with a corrosion inhibitor.

BraunNW (BLI) 18 of 36 Ford Type-3 Demo
4/9/24 3878-3
3 COATINGS AND FINISHES

3.02 MODULE PRIMER
Module shall be sealed with a two -component, low VOC, direct -to-metal epoxy primer/sealant prior to applying the finish coat of acrylic urethane paint.

3.03 PAINT TYPE
Shall be Sherwin Williams acrylic urethane.

3.04 COLOR SCHEME
Base color to match Race Red (G4-100871777)

Stripe #1 Color: White Multi Stripe
Width: 6” total, 0.25” pinstripe with 0.25” gap, 5” stripe with

0.25” gap 0.25” pinstripe
Style: Beltline
Material: Vinyl
Location: Streetside, Curbside and rear of module

3.04.01 CHASSIS COLOR
Chassis shall be OEM Race Red (PQ) (Section 1.01.11 related).

3.05 LETTERING/DECALS

STREET SIDE VIEW DEMO

Item #S1 Decal: “North Star”
Color: White
Size: 4” Lettering
Material: Vinyl
Location: Street side of Module centered

Item #S2 Decal: “Emergency Vehicles”
Font: Serpentine bold
Color: White
Size: 3”H x 51.25” L
Material: Vinyl
Location: Streetside of module centered below Item #S1

BraunNW (BLI) 19 of 36 Ford Type-3 Demo
4/9/24 3878-3

CURBSIDE VIEW DEMO

Item #C1 Decal: “North Star”
Color: White
Size: 4” Lettering
Material: Vinyl
Location: Curbside of module centered

Item #C2 Decal: “Emergency Vehicles”
Font: Serpentine bold
Color: White
Size: 3”H x 51.25” L
Material: Vinyl
Location: Curbside of module centered below Item #C1

3.07 INTERIOR CABINETRY FINISH
All interior cabinetry shall be sanded, etched, washed, primed, coated with textured polyurea thermoplastic elastomer, and painted white with light gray splatter paint. (G2 - 33631 Alt 2 / GLV-51748)
All drawers, shelves and trays shall be sanded, etched, washed, primed, and painted white with light gray splatter paint. (G2-33631 Alt 2 / GLV-51748)

3.08 MODULE UPHOLSTERY
Module upholstery material shall be Dove Gray Spradling Perform 60 seamless vinyl.

3.09 MODULE FLOORING MATERIAL
Shall be Genome (#TFM2702) Altro Transflor Meta Slip -Retardant Sheet flooring providing durability, ease of maintenance and stain r esistance. It shall contain a high concentration of microscopic aluminum oxide particles and colored quartz crystals suspended throughout the thickness with silicon carbide grains in the entire wear surface for slip-retardant performance. It shall have an overall thickness of 0.11″ nominal. Flooring shall be manufactured for Wear Resistance to meet ASTM C 501, indentation resistance in accordance with ASTM F 1303 and ASTM F 970, Grade 1 standards, shall meet ASTM D 2047 Slip Retardant, ASTM F 970 Static Load, ASTM E648, CMVSS, FMVSS 302, CAN ULC S102.2 Fire Data Tests. (Section 5.04 related)
An insulated floor shall be installed over the 0.125″ aluminum subfloor and shall be comprised of 0.75″ thick polyiso insulation between 0.75″ x 0.75″ x 0.063″ square tubing, covered with a 0.125″ aluminum sheet (Section 2.04 related).

Floor covering material shall be seamless and cove up the side walls a minimum of 5″ as a seal.

BraunNW (BLI) 20 of 36 Ford Type-3 Demo
4/9/24 3878-3

3.10 COMPARTMENT LINING
Compartment floors shall be lined with light gray Matéflex floor t ile and all shelves with mat.

3.11 CABINET LINING
Interior cabinet shelves shall be lined with easy sweep mats which are removable for ease of cleaning.

3.12 SURFACES AND FINISHES
All patient compartment surfaces and finishes shall be impervious to soap, disinfectants, and water, to permit washing and sanitizing.

BraunNW (BLI) 21 of 36 Ford Type-3 Demo
4/9/24 3878-3
4 MODULE EXTERIOR

4.01 STEP/BUMPER
The rear bumper shall be a welded construction of 3″ x 3″ x 0.375″ aluminum angle and

1.5″ x 0.25″ flat bar and shall be covered by 0.125″ bright aluminum di amond plate. The center section, below the doors, shall have a hex -punched open flow design to prevent accumulation of water and snow and provide a 7″ step. Both outermost ends shall be angled to prevent dragging of corners in high angle of departure areas . Diamond plate shall be formed on front and rear edges for channel -type strength, and a formed 0.090″ aluminum closeout shall be welded to the underside of the bumper. The bumper shall be bolted directly to the chassis frame using high strength Grade 5 bo lts. Bumper shall be easily removable and replaceable in case of damage. Bumper to be designed to accommodate a one-person-style cot.

4.02 RUB RAILS
Bright finished extruded aluminum rub rails of a double channel design shall be installed along the lower streetside and curbside edges of the module. Rub rails shall be 2.5″H x

0.75″W x 0.125″D, with a 0.5ʺH red/white conspicuity reflective tape installed in the insert area.

4.03 FENDER RINGS
Bright polished aluminum fender rings with a rounded outer edge shall be installed on the module, following the full contour of the wheel well opening.

4.04 DRIP RAIL
Extruded, anodized aluminum drip rails shall be installed the full length of the module front, rear, and sides near the roof . Drip rails shall be in stalled with bonding tape and mechanical fasteners on each end that shall withstand exposure to the elements. They shall be finished with 45-degree angled ends to avoid hooking materials which brush against the vehicle causing damage.

BraunNW (BLI) 22 of 36 Ford Type-3 Demo
4/9/24 3878-3

4.09 FUEL SPLASH GUARD
A stainless-steel fuel splash guard shall be installed below the fuel fill.

4.16B REAR LICENSE PLATE
A recessed license plate holder with dua l Whelen #0AC0EDCR LED lights with angled chrome bezels shall be installed below rear doors in the rear kick panel (Section 4.06 related).

A hidden unlock switch shall be installed behind the license plate (Section 6.40 related).

4.19A SPARE TIRE MOUNT
An aluminum mounting plate for the OEM spare tire shall be installed in Compartment #1.

The spare tire shall be mounted on the bracket.

BraunNW (BLI) 23 of 36 Ford Type-3 Demo
4/9/24 3878-3
5 MODULE INTERIOR
All interior hangers, supports, fasteners, latches, and hinges shall be of a near -flush-type design. The patient compartme nt shall be free of sharp projections. Exposed edges and corners shall be broken with a radius or protected with 1″ high-density foam covered with heavy-duty vinyl color-matched upholstery.

5.02 HEADLINER
The headliner shall be 0.125 ″ aluminum which is sanded, etched, washed, primed, and coated with textured polyurea thermoplastic elastomer, and painted white with light gray splatter paint (G2-33631 Alt 2 / GLV-51748).

1.5″ foam covered with heavy-duty seamless vinyl upholstery.

Seat cushions shall be 3″ foam covered with heavy-duty seamless vinyl upholstery (Section

3.08 related).

5.04 LOWER WALL COVERING
The squad bench sides and lower portion of the streetside wall shall be nonporous, color - coordinated material.

5.05 GRAB RAIL(S)
One 75″L x 1.250″D stainless steel grab rail with three support brackets shall be securely mounted to roof structural framing running through centerline.

5.06 ACCESS DOOR GRAB RAILS
Each module access door shall have a 1.250″D L -style stainless steel grab handle which may also be used as an entry assist rail.

5.07 IV HANGER(S)
One retractable dual IV hanger with stabilizers shall be surface-mounted in the ceiling over the primary cot.

BraunNW (BLI) 24 of 36 Ford Type-3 Demo
4/9/24 3878-3

5.08C COT MOUNT
A Stryker #6390-700-001 floor plate shall be installed by BNW, to position the aft end of the cot 11″ forward of the rear doors (Section 8.02 related).

5.10 ATTENDANT SEAT
A Wise #1655 rear-facing high-back bucket seat, upholstered with heavy grade vinyl, Dove gray, shall be located at the head of the cot position and provide easy access to all action wall controls and outlets, and to the patient. Seat shall have a four-point seat belt and shall be securely anchored to a #1934 swivel base.

5.11 OXYGEN SYSTEM
The entire oxygen system shall be assembled with certified oxygen hose (1000 PSI burst strength) with brass fittings, be pressure tested, and certified. A 50 PSI regulator shal l be included, and one oxygen tank wrench shall be attached to the wall with hook -and-loop tape. A bulkhead connector shall be installed in the ceiling of Compartment #3.

Three Ohio-type outlets shall be installed:

1. One in Action Area #8

2. One on the curbside wall above the squad bench

3. One in ceiling above the primary patient

5.13 SUCTION COLLECTOR
A Rico model #RS4X-1001B suction regulator and wall-mount bracket with a 1200cc Rico disposable canister shall be installed in the Action Area #8.

5.15 FLUID BARRIER
A formed stainless steel floor mounted fluid barrier which is 0.75″ high shall be provided between the module and cab. This barrier shall prevent f luids from running from the module floor into cab area.

BraunNW (BLI) 25 of 36 Ford Type-3 Demo
4/9/24 3878-3

Roof, doors, wall, and floor insulation shall be polyisocyanurate.

A 3″ wide, 60-mil, closed cell polyethylene foam tape shall be used as a thermal break on the inside surface of the wall tubes.

5.17 MODULE CLIMATE CONTROL SYSTEM
The module HVAC system shall incorporate a combination heating/air conditioning unit with 43,300 BTU/hr. heating and 32,000 BTU/hr. cooling capacity. The unit shall have a 580 CFM fan and controls independent of the cab system. A 12VDC booster pump shall be installed to optimize the heating capacity in the module. A return air path with open area equal to at least twice the blower outlet area shall be inco rporated into the evaporator closeout.

The module system shall be controllable by a digital thermostat located on the streetside wall in the Action Area #8.

Four vents shall be installed in a vertical plenum on the aisle side of right front stack, spaced evenly.

A Beam #015715 metal wall port shall be installed in the vertical plenum to provide direct heat to a patient. A hose shall be shipped loose (Section 8.01 related).

5.19 AIR RETURN
A return air path with an open area equal to at least twice the blower outlet area shall be incorporated into the evaporator closeout.

5.24 CLOCK
An atomic-controlled clock shall be installed on Cabinet #14 door. The clock shall be LCD display and show hours (12/24 selectable), minutes, seconds, date, da y, and temperature.

Clock is powered by two AA alkaline batteries.

BraunNW (BLI) 26 of 36 Ford Type-3 Demo
4/9/24 3878-3

A 5 Qt. Sage #85131 biohazard waste/sharps container and a 7 qt. waste container shall be installed on the curbside squad bench end bar (Section 5.34A related).

5.29 OXYGEN WINDOW
A 6″ x 11″ clear polycarbonate oxygen window with knob and self-closing hinges shall be installed.

1.25″ satin finish stainless steel post bases attached to the front of the squad bench.

BraunNW (BLI) 27 of 36 Ford Type-3 Demo
4/9/24 3878-3
6 ELECTRICAL
All added body and chassis electrical equipment shall be served by circuits separate and distinct from the vehicle chassis circ uits. All vehicle wiring shall be copper and conform to all SAE J1128 requirements. The wiring shall be colored, numbered, or function coded every 3″ for permanent identification and correspond with the vehicle schematics.

The vehicle electrical system shall be tested and certified to AMD 005 requirements.

6.01 ELECTRICAL LOAD DEVICES
Body electrical wiring shall utilize overload protective devices of the automotive -type circuit breaker. In addition, one single pole, 20-amp circuit breaker shall be pro vided for future use. The circuit breakers, relays, and other electrical devices shall be included as part of the enclosed electrical component module located in Cabinet #14.

Display flashes to indicate low voltage.

A buzzer shall indicate low voltage.

6.05B MODULE POWER
Module power shall be controlled by a driver's console -mounted switch labeled ″MODULE DISC.″ which activates an InPower #SSC42-275 solid state contactor (Section

6.06 WIRING ACCESS
All cabinets and compartments shall have removable panels as needed to access wiring harnesses and hoses.

BraunNW (BLI) 28 of 36 Ford Type-3 Demo
4/9/24 3878-3

6.07 BACK-UP ALARM
An SAE J994-compliant self-adjusting back-up alarm shall be installed, without a disable switch.

6.08 SERVICE LOOP
A 6″ service loop of wire or harness shall be provided at all electrical components, terminals, and connection points.

1. Passage
Compt.

D/O
Lights

2. 3.

Siren Module
Disc.

Emerg.

Master Blank

4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14.

Blank White
Lights Blank
Blank
(Opticom
Circuit)
Blank Blank Spare Left
Scene
Right
Scene
Rear
Scene
USB
A/C

6.10 SWITCHES
Switches installed in the driver's console and attendant panel(s) shall be rocker -type and permanently marked by function.

BraunNW (BLI) 29 of 36 Ford Type-3 Demo
4/9/24 3878-3

6.13 ATTENDANT CONTROL PANEL
A six-switch attendant control panel shall be located on the streetside wall in the Action Area #8 with the following switch layout:

1. 2. 3. 4. 5. 6.

Left Dome
Hi-Lo-Off
Right Dome
Hi-Lo-Off Suction Vent Attendant
Light USB A/C

A digital thermostat and an inverter status panel shall be located adjacent to the attendant control panel (Sections 5.17 and 6.31 related).

6.15A STEP LIGHT
A Whelen #3SC0CDCR Clear Lens Clear 3″ LED light shall be installed on the forward wall of the curbside door stepwell.

Pressing the top of the switches shall increase intensity. Pressing the bottom of the switches shall decrease intensity.

BraunNW (BLI) 30 of 36 Ford Type-3 Demo
4/9/24 3878-3

Module identification lights, clearance lights, and side marker lights, unless included on a lightbar, shall be Truck-Lite LED Model 36.

Rear and side reflex reflectors shall be installed in accordance with FMVSS 108 requirements.

6.20 BLOCK HEATER
A block heater, with circuit breaker in the 120VAC Power Box, shall be wired to the 120VAC shorepower system (Section 1.01.02 related).

6.21 120VAC/SHORELINE CIRCUIT BOX
Utility power shall be furnished from 120VAC shorepower via a Kussmaul 20-amp Super Auto-Eject plug with a white cover on a stainless steel plate with a green indicator light located on the driver's side of vehicle and distributed via a formed aluminum power box recessed into the streetside front compartment. 120VAC power box shall be recessed and shall have an easily removable cover.

Five interior 120VAC GFCI duplex receptacles shall be mounted:
• One in Compartment #1
• One in Cabinet #1
• One in Cabinet #5
• One in Action Area #8
• One in Cabinet #19

BraunNW (BLI) 31 of 36 Ford Type-3 Demo
4/9/24 3878-3

6.23 BATTERY CHARGER
A 60-amp battery charger shall be provided as part of the Samlex Pure Sine 1200 -watt inverter system. (Section 6.31 related)

6.24A BATTERY MODIFICATIONS
The two OEM batteries shall be relocated to the curbside forward exterior compartment on a 300 lb battery tray with a locking right slide . The batteries shall be interconnected to provide maximum cold cranking amps and reserve capacity at all times.

6.25 12VDC POWER SUPPLY
Two 12VDC, 15-amp lighter-style power point receptacles shall be provided; – One Action Area #8
– One Cabinet #19
Two Kussmaul USB A/C dual charge ports shall be installed:
– One in Action Area #8
– One in the driver’s console
All 12VDC power point receptacles, USB charge ports, 12VDC charging circuits, electric air compressors, and cool cabinets, if present, shall be powered from a 12VDC auxiliary bus. An InPower LVD20-100-SPC540 low voltage disconnect switch shall deliver power to the auxiliary bus only when the supply voltage to the vehicle batteries is at or above 13.0 VDC.

6.26 COMPARTMENT LIGHTING
LED strip lighting shall be installed in each outside compartment, and shall be activated by the respective compartment door switch.

6.27 EXTERIOR DOOR SWITCHES
Shall be 1/2″ mechanical door switches.

BraunNW (BLI) 32 of 36 Ford Type-3 Demo
4/9/24 3878-3

6.30.01 FRONT LIGHTBAR
A 94″ Whelen 4500 Plus Series LED lightbar shall be recessed on the front of the module, pattern curbside to streetside:

The rear lightbar shall be controlled by the “EMERG. MASTER” switch in the driver's console. The white flashers shall be disabled when the vehicle is shifted into park.

The white lights shall also be controlled by the ʺWHITE LIGHTSʺ switch in the driver's console.

BraunNW (BLI) 33 of 36 Ford Type-3 Demo
4/9/24 3878-3

6.30.02 REAR LIGHTBAR
A 94″ Whelen 4500 Plus Series LED lightbar shall be recessed on the rear of the module, pattern curbside to streetside:

The rear lightbar shall be controlled by the “EMERG. MASTER” switch in the driver's console.

6.30.03 FLASHERS
Four Whelen #M9RC Clear Lens Red Super-LED flashers shall be mounted two each on the curbside and street side of the module in upper corners.

Two Whelen #M9AC Clear Lens Amber Super-LED flashers shall be mounted on the rear of the vehicle in line with the rear entrance door windows.

Lights shall be controlled by the “EMERG. MASTER” switch on the driver's console (Section 6.09 related).

Two Whelen #WIONSMCR Clear Lens Red flashers with chrome housings shall be installed on the rear of the module lower , one streetside, and one c urbside just above the rear kick panel. Lights shall be controlled by the ″EMERG. MASTER″ switch on the driver's console (Section 6.09 related).

BraunNW (BLI) 34 of 36 Ford Type-3 Demo
4/9/24 3878-3

6.30.04 SCENELIGHTS
Four Whelen #M9LZC Scene Super-LED light heads shall be mounted, two each on the curbside and streetside of the module in upper corners.

The curbside passage door shall activate the curbside scene lights. The scene lights shall also be controlled by the respective switches on the driver's console (Section 6.09 related).

Two Whelen LR-11 LED scene lights shall be included in the rear lightbar. The rear scene lights shall be controlled by the “REAR SCENE” switch on the driver's console (Section

6.09 related), and shall activate when the rear curbside passage door is opened or when the vehicle is placed in reverse.

6.30.05 SPOTLIGHT
A Golight # 20204 roof-mounted LED spotlight with white housing and a stainless -steel mounting bracket shall be installed on the center of the cab ro of. A hard-wired controller shall be mounted on the OEM coin holder slot on the cab dash.

6.30.06 INTERSECTION LIGHTS
Four Whelen #WIONSMCR Clear Lens Red LED flashers with chrome housings shall be installed, one on each cab fender and one above each mod ule wheel well. Lights shall be controlled by the “EMERG. MASTER ” switch on the driver's console (Section 6.09 related).

A pre-wire shall be provided from the electrical panel to the grille area for future use of White Lights as wig wags.

A pre-wire shall be provided from the electrical panel to the grille area for future use of a grille light as steady red.

6.30.10 SIREN SPEAKERS
Two Federal Signal Dynamax #ES100C 100 watt speakers with North Star stainless steel grilles shall be installed in the OEM bumper.

BraunNW (BLI) 35 of 36 Ford Type-3 Demo
4/9/24 3878-3

A hidden unlock switch shall be installed behind the license plate on the rear of the module (Section 4.16 related).

6.46 AUDIO/VIDEO/RECORDING EQUIPMENT
Item #1
Description: A Rostra back-up camera kit shall be installed, including a surface-mounted camera and a rear-view mirror/monitor with a 4.3″ screen.

Location: Camera on the rear of the module, c entered above the rear passage doors.

Rearview mirror/monitor centered on chassis windshield, upper.

Additional Instructions: Camera shall automatically display on monitor when the vehicle is placed in reverse. The programming remote shall be shipped loose (Section 8.01 related).

BraunNW (BLI) 36 of 36 Ford Type-3 Demo
4/9/24 3878-3
7 SUPPORTING DOCUMENTATION

7.01 OWNERS MANUAL
Shall be provided with vehicle and consists of the following items:

1. Braun Northwest Contact Information

2. Table of Contents

3. Manufacturers’ Labels

4. Electrical Load Test/Payload/Paint Stickers

5. Braun Northwest Warranties
Lifetime module warranty
Seven-year/75,000-mile limited electrical warranty
Two-year/30,000-mile conversion warranty
Five-year paint warranty
Chemical De-Icer Statement

6. Service and Operations manual

7. Electrical
Wire charts and plug pinouts
Harness layout
Schematics

8. Parts list

9. Paint information

10. Products and Information

11. Second OEM chassis key

8 MISCELLANEOUS EQUIPMENT

8.01 LOOSE EQUIPMENT
The following equipment shall be shipped loose with the vehicle:

1. Touch Up Paint
• Race Red G4-100871777
• White G2-33631 Alt 2
• Gray GLV-51748

2. Spare tire and wheel

3. Antenna Coax Ends

4. Adjustable shelf for compartment #1

5. Road Safety Kit (includes flares, triangle and fire extinguisher) (For BNW Demo period)

6. 12.5'L hose

* * * * * *

H-GAC
Houston-Galveston Area Council
P.O. Box 22777 · 3555 Timmons · Houston, Texas 77227-2777 Cooperative Agreement - Contract - Braun Northwest, Inc. - Public Services - ID: 11091

Page 1 of 13 ends

MASTER GENERAL PROVISIONS

This Master Agreement is made and entered into, by and between the Houston-Galveston Area Council hereinafter referred to as H-GAC having its principal place of business at 3555 Timmons Lane, Suite 120, Houston, Texas 77027 and Braun Northwest, Inc., hereinafter referred to as the Contractor, having its principal place of business at 150 North Star Drive, Chehalis, WA 98532.

WITNESSETH:

WHEREAS, H-GAC hereby engages the Contractor to perform certain services in accordance with the specifications of the Master Agreement; and

WHEREAS, the Contractor has agreed to perform such services in accordance with the specifications of the Master Agreement;

NOW, THEREFORE, H-GAC and the Contractor do hereby agree as follows:

ARTICLE 1: LEGAL AUTHORITY
The Contractor warrants and assures H-GAC that it possesses adequate legal authority to enter into this Master Agreement. The Contractor's governing body, where applicable, has authorized the signatory official(s) to enter into this Master Agreement and bind the Contractor to the terms of this Master Agreement and any subsequent amendments hereto.

ARTICLE 2: APPLICABLE LAWS
The Contractor agrees to conduct all activities under this Master Agreement in accordance with all federal laws, executive orders, policies, procedures, applicable rules, regulations, directives, standards, ordinances, and laws, in effect or promulgated during the term of this Master Agreement, including without limitation, workers’ compensation laws, minimum and maximum salary and wage statutes and regulations, and licensing laws and regulations. When required, the Contractor shall furnish H-GAC with satisfactory proof of its compliance therewith.

ARTICLE 3: PUBLIC INFORMATION
Except as stated below, all materials submitted to H-GAC, including any attachments, appendices, or other information submitted as a part of a submission or Master Agreement, are considered public information, and become the property of H-GAC upon submission and may be reprinted, published, or distributed in any manner by H-GAC according to open records laws, requirements of the US Department of Labor and the State of Texas, and H-GAC policies and procedures. In the event the Contractor wishes to claim portions of the response are not subject to the Texas Public Information Act, it shall so; however, the determination of the Texas Attorney General as to whether such information must be disclosed upon a public request shall be binding on the Contractor. H-GAC will request such a determination only if Contractor bears all costs for preparation of the submission. H-GAC is not responsible for the return of creative examples of work submitted. H-GAC will not be held accountable if material from submissions is obtained without the written consent of the contractor by parties other than H-GAC, at any time during the evaluation process.

ARTICLE 4: INDEPENDENT CONTRACTOR
The execution of this Master Agreement and the rendering of services prescribed by this Master Agreement do not change the independent status of H-GAC or the Contractor. No provision of this Master Agreement or act of H- GAC in performance of the Master Agreement shall be construed as making the Contractor the agent, servant, or employee of H-GAC, the State of Texas, or the United States Government. Employees of the Contractor are DocuSign Envelope ID: E4D77477-E07A-45AE-A42F-916BF5C46EDC

Page 2 of 13 ends

subject to the exclusive control and supervision of the Contractor. The Contractor is solely responsible for employee related disputes and discrepancies, including employee payrolls and any claims arising therefrom.

ARTICLE 5: ANTI-COMPETITIVE BEHAVIOR
Contractor will not collude, in any manner, or engage in any practice which may restrict or eliminate competition or otherwise restrain trade.

ARTICLE 6: SUSPENSION AND DEBARMENT
Debarment and Suspension (Executive Orders 12549 and 12689) – A contract award (2 CFR 180.220) must not be made to parties listed on the government-wide exclusions in the System for Award Management (SAM), in accordance with the OMB guidelines at 2 CFR 180 that implement Executive Orders 12549 (3 CFR Part 1966 Comp. p. 189) and 12689 (3 CFR Part 1989 Comp. p. 235), “Debarment and Suspension.” SAM Exclusions contains the names of parties debarred, suspended, or otherwise excluded by agencies, as well as parties declared ineligible under statutory or regulatory authority other than Executive Order 12549.

Pursuant to the Federal Rule above, Respondent certifies that neither it nor its principals are presently debarred, suspended, proposed for debarment, declared ineligible, or voluntarily excluded from participation by any federal department or agency or by the State of Texas and at all times during the term of the Contract neither it nor its principals will be debarred, suspended, proposed for debarment, declared ineligible, or voluntarily excluded from participation by any federal department or agency or by the State of Texas Respondent shall immediately provide the written notice to H-GAC if at any time the Respondent learns that this certification was erroneous when submitted or has become erroneous by reason of changed circumstances. H-GAC may rely upon a certification of the Respondent that the Respondent is not debarred, suspended, ineligible, or voluntarily excluded from the covered contract, unless the H-GAC knows the certification is erroneous.

ARTICLE 7: GOAL FOR CONTRACTING WITH SMALL AND MINORITY BUSINESSES, WOMEN’S BUSINESS ENTERPRISES, AND LABOR SURPLUS AREA FIRMS (if subcontracts are to be let) H-GAC’s goal is to assure that small and minority businesses, women's business enterprises, and labor surplus area firms are used when possible in providing services under a contract. In accordance with federal procurements requirements of 2 CFR §200.321, if subcontracts are to be let, the prime contractor must take the affirmative steps listed below:

1. Placing qualified small and minority businesses and women’s business enterprises on solicitation lists;

2. Assuring that small and minority businesses and women’s business enterprises are solicited whenever they are potential sources;

3. Dividing total requirements, when economically feasible, into smaller task or quantities to permit maximum participation by small and minority businesses, and women’s business enterprises;

4. Establishing delivery schedules, where the requirement permits, which encourage participation by small and minority businesses, and women’s business enterprises;

5. Using the services and assistance as appropriate, of such organizations as the Small Business Administration and the Minority Business Development Agency of the Department of Commerce.

6. Nothing in this provision will be construed to require the utilization of any firm that is either unqualified or unavailable. The Small Business Administration (SBA) is the primary reference and database for information on requirements related to Federal Subcontracting https://www.sba.gov/federal-contracting/contracting-guide/prime- subcontracting

NOTE: The term DBE as used in this solicitation is understood to encompass all programs/business enterprises such as: Small Disadvantaged Business (SDB), Historically Underutilized Business (HUB), Minority Owned Business Enterprise (MBE), Women Owned Business Enterprise (WBE) and Disabled Veteran Business Enterprise (DVBE) or other designation as issued by a certifying agency.

Contractor agrees to work with and assist HGACBuy customer in meeting any DBE targets and goals, as may be required by any rules, processes, or programs they might have in place. Assistance may include compliance with reporting requirements, provision of documentation, consideration of Certified/Listed subcontractors, provision of documented evidence that an active participatory role for a DBE entity was DocuSign Envelope ID: E4D77477-E07A-45AE-A42F-916BF5C46EDC

Page 3 of 13 ends

considered in a procurement transaction, etc.

ARTICLE 8: SCOPE OF SERVICES
The services to be performed by the Contractor are outlined in an Attachment to this Master Agreement.

ARTICLE 9: PERFORMANCE PERIOD
This Master Agreement shall be performed during the period which begins Oct 01 2023 and ends Sep 30 2027. All services under this Master Agreement must be rendered within this performance period, unless directly specified under a written change or extension provisioned under Article 21, which shall be fully executed by both parties to this Master Agreement.

ARTICLE 10: PAYMENT OR FUNDING
Payment provisions under this Master Agreement are outlined in the Special Provisions. H-GAC will not pay for any expenses incurred prior to the execution date of a contract, or any expenses incurred after the termination date of the contract.

ARTICLE 11: PAYMENT FOR WORK
The H-GAC Customer is responsible for making payment to the Contractor upon delivery and acceptance of the goods or completion of the services and submission of the subsequent invoice.

ARTICLE 12: PAYMENT TERMS/PRE-PAYMENT/QUANTITY DISCOUNTS If discounts for accelerated payment, pre-payment, progress payment, or quantity discounts are offered, they must be clearly indicated in the Contractor’s submission prior to contract award. The applicability or acceptance of these terms is at the discretion of the Customer.

ARTICLE 13: REPORTING REQUIREMENTS
If the Contractor fails to submit to H-GAC in a timely and satisfactory manner any report required by this Master Agreement, or otherwise fails to satisfactorily render performances hereunder, H-GAC may terminate this Master Agreement with notice as identified in Article 29 of these General Provisions. H-GAC has final determination of the adequacy of performance and reporting by Contractor. Termination of this Master Agreement for failure to perform may affect Contractor’s ability to participate in future opportunities with H-GAC. The Contractor's failure to timely submit any report may also be considered cause for termination of this Master Agreement. Any additional reporting requirements shall be set forth in the Special Provisions of this Master Agreement.

ARTICLE 14: INSURANCE
Contractor shall maintain insurance coverage for work performed or services rendered under this Master Agreement as outlined and defined in the attached Special Provisions.

ARTICLE 15: SUBCONTRACTS AND ASSIGNMENTS
Except as may be set forth in the Special Provisions, the Contractor agrees not to assign, transfer, convey, sublet, or otherwise dispose of this Master Agreement or any right, title, obligation, or interest it may have therein to any third party without prior written approval of H-GAC. The Contractor acknowledges that H-GAC is not liable to any subcontractor or assignee of the Contractor. The Contractor shall ensure that the performance rendered under all subcontracts shall result in compliance with all the terms and provisions of this Master Agreement as if the performance rendered was rendered by the Contractor. Contractor shall give all required notices, and comply with all laws and regulations applicable to furnishing and performance of the work. Except where otherwise expressly required by applicable law or regulation, H-GAC shall not be responsible for monitoring Contractor's compliance, or that of Contractor’s subcontractors, with any laws or regulations.

ARTICLE 16: AUDIT
Notwithstanding any other audit requirement, H-GAC reserves the right to conduct or cause to be conducted an independent audit of any transaction under this Master Agreement, such audit may be performed by the H-GAC local government audit staff, a certified public accountant firm, or other auditors designated by H-GAC and will be DocuSign Envelope ID: E4D77477-E07A-45AE-A42F-916BF5C46EDC

Page 4 of 13 ends

conducted in accordance with applicable professional standards and practices. The Contractor understands and agrees that the Contractor shall be liable to the H-GAC for any findings that result in monetary obligations to H- GAC.

ARTICLE 17: TAX EXEMPT STATUS
H-GAC and Customer members are either units of government or qualified non-profit agencies, and are generally exempt from Federal and State sales, excise or use taxes. Respondent must not include taxes in its Response. It is the responsibility of Contractor to determine the applicability of any taxes to an order and act accordingly.

Exemption certificates will be provided upon request.

ARTICLE 18: EXAMINATION OF RECORDS
The Contractor shall maintain during the course of the work complete and accurate records of all of the Contractor's costs and documentation of items which are chargeable to H-GAC under this Master Agreement. H- GAC, through its staff or designated public accounting firm, the State of Texas, and United States Government, shall have the right at any reasonable time to inspect, copy and audit those records on or off the premises by authorized representatives of its own or any public accounting firm selected by H-GAC. The right of access to records is not limited to the required retention period, but shall last as long as the records are retained. Failure to provide access to records may be cause for termination of the Master Agreement. The records to be thus maintained and retained by the Contractor shall include (without limitation): (1) personnel and payroll records, including social security numbers and labor classifications, accounting for total time distribution of the Contractor's employees working full or part time on the work, as well as cancelled payroll checks, signed receipts for payroll payments in cash, or other evidence of disbursement of payroll payments; (2) invoices for purchases, receiving and issuing documents, and all other unit inventory records for the Contractor's stocks or capital items; and (3) paid invoices and cancelled checks for materials purchased and for subcontractors' and any other third parties' charges.

Contractor agrees that H-GAC will have the right, with reasonable notice, to inspect its records pertaining to purchase orders processed and the accuracy of the fees payable to H-GAC. The Contractor further agrees that the examination of records outlined in this article shall be included in all subcontractor or third-party Master Agreements.

ARTICLE 19: RETENTION OF RECORDS
The Contractor and its subcontractors shall maintain all records pertinent to this Master Agreement, and all other financial, statistical, property, participant records, and supporting documentation for a period of no less than seven (7) years from the later of the date of acceptance of the final payment or until all audit findings have been resolved.

If any litigation, claim, negotiation, audit or other action involving the records has been started before the expiration of the retention period, the records shall be retained until completion of the action and resolution of all issues which arise from it, or until the end of the seven (7) years, whichever is later, and until any outstanding litigation, audit, or claim has been fully resolved.

ARTICLE 20: DISTRIBUTORS, VENDORS, RESELLERS
Contractor agrees and acknowledges that any such designations of distributors, vendors, resellers or the like are for the convenience of the Contractor only and the awarded Contractor will remain responsible and liable for all obligations under the Contract and the performance of any designated distributor, vendor, reseller, etc. Contractor is also responsible for receiving and processing any Customer purchase order in accordance with the Contract and forwarding of the Purchase Order to the designated distributor, vendor, reseller, etc. to complete the sale or service.

H-GAC reserves the right to reject any entity acting on the Contractor’s behalf or refuse to add entities after a contract is awarded.

ARTICLE 21: CHANGE ORDERS AND AMENDMENTS
A. Any alterations, additions, or deletions to the terms of this Master Agreement, which are required by changes in federal or state law or by regulations, are automatically incorporated without written amendment hereto, and shall become effective on the date designated by such law or by regulation.

DocuSign Envelope ID: E4D77477-E07A-45AE-A42F-916BF5C46EDC

Page 5 of 13 ends

B. To ensure the legal and effective performance of this Master Agreement, both parties agree that any amendment that affects the performance under this Master Agreement must be mutually agreed upon and that all such amendments must be in writing. After a period of no less than 30 days subsequent to written notice, unless sooner implementation is required by law, such amendments shall have the effect of qualifying the terms of this Master Agreement and shall be binding upon the parties as if written herein.

C. Customers have the right to issue a change order to any purchase orders issued to the Contractor for the purposes of clarification or inclusion of additional specifications, qualifications, conditions, etc. The change order must be in writing and agreed upon by Contractor and the Customer agency prior to issuance of any Change Order. A copy of the Change Order must be provided by the Contractor to, and acknowledged by, H-GAC.

ARTICLE 22: CONTRACT ITEM CHANGES
A. If a manufacturer discontinues a contracted item, that item will automatically be considered deleted from the contract with no penalty to Contractor. However, H-GAC may at its sole discretion elect to make a contract award to the next lowest Respondent for the item, or take any other action deemed by H-GAC, at its sole discretion, to be in the best interests of its Customers.

B. If a manufacturer makes any kind of change in a contracted item which affects the contract price, Contractor must advise H-GAC of the details. H-GAC may allow or reject the change at its sole discretion.

If the change is rejected, H-GAC will remove the item from its program and there will be no penalty to Contractor. However, H- GAC may at its sole discretion elect to make a contract award to the next lowest Respondent for the item, or take any other action deemed by H-GAC, at its sole discretion, to be in the best interests of its Customers.

C. If a manufacturer makes any change in a contracted item which does not affect the contract price, Contractor shall advise H-GAC of the details. If the 'new' item is equal to or better than the originally contracted item, the 'new' item shall be approved as a replacement. If the change is rejected H-GAC will remove the item from its program and there will be no penalty to Contractor. However, H-GAC may at its sole discretion elect to make a contract award to the next lowest Respondent for the item or may take any other action deemed by H-GAC at its sole discretion, to be in the best interests of its Customers.

D. In the case of specifically identified catalogs or price sheets which have been contracted as base bid items or as published options, routine published changes to products and pricing will be automatically incorporated into the contract. However, Contractor must still provide written notice and an explanation of the changes to products and pricing. H-GAC will respond with written approval.

ARTICLE 23: CONTRACT PRICE ADJUSTMENTS
Price Decreases
If Contractor’s Direct Cost decreases at any time during the full term of this award, Contractor must immediately pass the decrease on to H-GAC and lower its prices by the amount of the decrease in Direct Cost. (Direct Cost means Contractor’s cost from the manufacturer of any item or if Contractor is the manufacturer, the cost of raw materials required to manufacture the item, plus costs of transportation from manufacturer to Contractor and Contractor to H-GAC. Contractor must notify H-GAC of price decreases in the same way as for price increases set out below. The price decrease shall become effective upon H-GAC’s receipt of Contractor’s notice. If Contractor routinely offers discounted contract pricing, H-GAC may request Contractor accept amended contract pricing equivalent to the routinely discounted pricing.

Price Increase
Contractors may request a price increase for items priced as Base Bid items and Published Options. The amount of any increase will not exceed actual documented increase in Contractor’s Direct Cost and will not exceed 10% of DocuSign Envelope ID: E4D77477-E07A-45AE-A42F-916BF5C46EDC

Page 6 of 13 ends

the previous bid price. Considerations on the percentage limit will be given if the price increase is the result of increased tariff charges or other governmental actions, or other economic factors. Manufacturer price/contract changes involving the sale of motor vehicles will be considered and may be allowed during the entire contract period subject to submission and verification of the proper documentation required for a contract change as referenced in this section.

Price Changes
Any permanent increase or decrease in offered pricing for a base contract item or published option is considered a price change. Temporary increases in pricing by whatever name (e.g., ‘surcharge’, ‘adjustment’, ‘equalization charge’, ‘compliance charge’, ‘recovery charge’, etc.), are also considered to be price changes.

For published catalogs and price sheets as part of an H-GAC contract, requests to amend the contract to reflect any new published catalog or price sheet must be submitted whenever the manufacturer publishes a new document.

The request must include the new catalog or price sheet. All Products shall, at time of sale, be equipped as required under any then current applicable local, state, and federal government requirements. If, during any contract, changes are made to any government requirements which cause a manufacturer's costs of production to increase, Contractor may increase pricing to the extent of Contractor’s actual cost increase. The increase must be substantiated with support documentation acceptable to H-GAC prior to taking effect. Modifications to a Product required to comply with such requirements which become effective after the date of any sale are the responsibility of the Customer.

Requesting Price Increase/Required Documentation
Contractor must submit a written overview of changes requested and reasons for the request, stating the amount of the increase, along with an itemized list of any increased prices, showing the Contractor’s current price, revised price, the actual dollar difference and the percentage of the price increase by line item. Price change requests must be supported with substantive documentation (e.g., notices from suppliers and manufacturers of pricing changes in products, components, transportation, raw materials or commodities, and/or product availability, copies of invoices from suppliers, etc.) clearly showing that Contractor's actual costs have increased per the applicable line-item bid.

The Producer Price Index (PPI) may be used as partial justification, subject to approval by H-GAC, but no price increase based solely on an increase in the PPI will be allowed. This documentation should be submitted in Excel format to facilitate analysis and updating of the website. The letter and documentation must be sent to Lead Program Coordinator, [email protected].

Review/Approval of Requests
If H-GAC approves the price increase, Contractor will be notified in writing; no price increase will be effective until Contractor receives this notice. If H-GAC does not approve Contractor’s price increase, Contractor may terminate its performance upon sixty (60) days advance written notice to H-GAC, however Contractor must fulfill any outstanding Purchase Orders. Termination of performance is Contractor’s only remedy if H-GAC does not approve the price increase. H-GAC reserves the right to accept or reject any price change request.

ARTICLE 24: DELIVERIES AND SHIPPING TERMS
The Contractor agrees to make deliveries only upon receipt of authorized Customer Purchase Order acknowledged by H-GAC. Delivery made without such Purchase Order will be at Contractor’s risk and will leave H-GAC the option of canceling any contract awarded to the Contractor. The Contractor must secure and deliver any item within five (5) working days, or as agreed to on any corresponding customer Purchase Order.

Shipping must be Freight On Board Destination to the delivery location designated on the Customer purchase order. The Contractor will retain title and control of all goods until delivery is completed and the Customer has accepted the delivery. All risk of transportation and all related charges are the responsibility of the Contractor. The Customer will notify the Contractor and H-GAC promptly of any damaged goods and will assist the Contractor in arranging for inspection. The Contractor must file all claims for visible or concealed damage. Unless otherwise stated in the Master Agreement, deliveries must consist only of new and unused merchandise.

ARTICLE 25: RESTOCKING (EXCHANGES AND RETURNS)
There will be no restocking charge to the Customer for return or exchange of any item purchased under the terms of any award. If the Customer wishes to return items purchased under an awarded contract, the Contractor agrees DocuSign Envelope ID: E4D77477-E07A-45AE-A42F-916BF5C46EDC

Page 7 of 13 ends

to exchange, these items for other items, with no additional charge incurred. Items must be returned to Contractor within thirty (30) days from date of delivery. If there is a difference in price in the items exchanged, the Contractor must notify H-GAC and invoice Customer for increase price or provide the Customer with a credit or refund for any decrease in price per Customer’s preference. On items returned, a credit or cash refund will be issued by the Contractor to Customer. This return and exchange option will extend for thirty (30) days following the expiration of the term of the Contract. All items returned by the Customer must be unused and in the same merchantable condition as when received. Items that are special ordered may be returned only upon approval of the Contractor.

ARTICLE 26: MANUALS
Each product delivered under contract to any Customer must be delivered with at least one (1) copy of a safety and operating manual and any other technical or maintenance manual. The cost of the manual(s) must be included in the price for the Product offered.

ARTICLE 27: OUT OF STOCK, PRODUCT RECALLS, AND DISCONTINUED PRODUCTS H-GAC does NOT purchase the products sold pursuant to a Solicitation or Master Agreement. Contractor is responsible for ensuring that notices and mailings, such as Out of Stock or Discontinued Notices, Safety Alerts, Safety Recall Notices, and customer surveys, are sent directly to the Customer with a copy sent to H-GAC.

Customer will have the option of accepting any equivalent product or canceling the item from Customer’s Purchase Order. Contractor is not authorized to make substitutions without prior approval.

ARTICLE 28: WARRANTIES, SALES, AND SERVICE
Warranties must be the manufacturer's standard and inclusive of any other warranty requirements stated in the Master Agreement; any warranties offered by a dealer will be in addition to the manufacturer’s standard warranty and will not be a substitute for such. Pricing for any product must be inclusive of the standard warranty.

Contractor is responsible for the execution and effectiveness of all product warranty requests and any claims, Contractor agrees to respond directly to correct warranty claims and to ensure reconciliation of warranty claims that have been assigned to a third party.

ARTICLE 29: TERMINATION PROCEDURES
The Contractor acknowledges that this Master Agreement may be terminated for Convenience or Default.

H-GAC will not pay for any expenses incurred after the termination date of the contract.

A. Convenience
H-GAC may terminate this Master Agreement at any time, in whole or in part, with or without cause, whenever H-GAC determines that for any reason such termination is in the best interest of H-GAC, by providing written notice by certified mail to the Contractor. Upon receipt of notice of termination, all services hereunder of the Contractor and its employees and subcontractors shall cease to the extent specified in the notice of termination.

The Contractor may cancel or terminate this Master Agreement upon submission of thirty (30) days written notice, presented to H-GAC via certified mail. The Contractor may not give notice of cancellation after it has received notice of default from H-GAC.

B. Default
H-GAC may, by written notice of default to the Contractor, terminate the whole or any part of the Master Agreement, in any one of the following circumstances:
(1) If the Contractor fails to perform the services herein specified within the time specified herein or any extension thereof; or
(2) If the Contractor fails to perform any of the other provisions of this Master Agreement for any reason whatsoever, or so fails to make progress or otherwise violates the Master Agreements that completion of services herein specified within the Master Agreement term is significantly endangered, and in either of these two instances does not cure such failure within a period of ten (10) days (or such longer period of time as may be authorized by H-GAC in writing) after receiving written notice by certified mail of default from H-GAC.

DocuSign Envelope ID: E4D77477-E07A-45AE-A42F-916BF5C46EDC

Page 8 of 13 ends

(3) In the event of such termination, Contractor will notify H-GAC of any outstanding Purchase Orders and H-GAC will consult with the End User and notify the Contractor to what extent the End User wishes the Contractor to complete the Purchase Order. If Contractor is unable to do so, Contractor may be subject to a claim for damages from H-GAC and/or the End User.

ARTICLE 30: SEVERABILITY
H-GAC and Contractor agree that should any provision of this Master Agreement be determined to be invalid or unenforceable, such determination shall not affect any other term of this Master Agreement, which shall continue in full force and effect.

ARTICLE 31: FORCE MAJEURE
To the extent that either party to this Master Agreement shall be wholly or partially prevented from the performance of any obligation or duty placed on such party by reason of or through strikes, stoppage of labor, riot, fire, flood, acts of war, insurrection, accident, order of any court, act of God, or specific cause reasonably beyond the party's control and not attributable to its neglect or nonfeasance, in such event, the time for the performance of such obligation or duty shall be suspended until such disability to perform is removed. Determination of force majeure shall rest solely with H-GAC.

ARTICLE 32: CONFLICT OF INTEREST
No officer, member or employee of the Contractor or Contractors subcontractor, no member of the governing body of the Contractor, and no other public officials of the Contractor who exercise any functions or responsibilities in the review or Contractor approval of this Master Agreement, shall participate in any decision relating to this Master Agreement which affects his or her personal interest, or shall have any personal or pecuniary interest, direct or indirect, in this Master Agreement.

A. Conflict of Interest Questionnaire: Chapter 176 of the Texas Local Government Code requires contractors contracting or seeking to contract with H-GAC to file a conflict-of-interest questionnaire (CIQ) if they have an employment or other business relationship with an H-GAC officer or an officer’s close family member.

The required questionnaire and instructions are located on the H-GAC website or at the Texas Ethics Commission website https://www.ethics.state.tx.us/forms/CIQ.pdf. H-GAC officers include its Board of Directors and Executive Director, who are listed on this website. Respondent must complete and file a CIQ with the Texas Ethics Commission if an employment or business relationship with H-GAC office or an officer’s close family member as defined in the law exists.

B. Certificate of Interested Parties Form – Form 1295: As required by Section 2252.908 of the Texas Government Code. H-GAC will not enter a Contract with Contractor unless (i) the Contractor submits a disclosure of interested parties form to H-GAC at the time the Contractor submits the contract H-GAC, or (ii) the Contractor is exempt from such requirement. The required form and instructions are located at the Texas Ethics Commission website https://www.ethics.state.tx.us/whatsnew/elf_info_form1295.htm.

Respondents who are awarded a Contract must submit their Form 1295 with the signed Contract to H-GAC.

ARTICLE 33: FEDERAL COMPLIANCE
Contractor agrees to comply with all federal statutes relating to nondiscrimination, labor standards, and environmental compliance. With regards to “Rights to Inventions Made Under a Contract or Master Agreement,” If the Federal award meets the definition of “funding Master Agreement” under 37 CFR § 401.2 (a) and the recipient or subrecipient wishes to enter into a contract with a small business firm or nonprofit organization regarding the substitution of parties, assignment or performance of experimental, developmental, or research work under that “funding Master Agreement,” the recipient or subrecipient must comply with the requirements of 37 CFR Part 401, “Rights to Inventions Made by Nonprofit Organizations and Small Business Firms Under Government Grants, Contracts and Cooperative Master Agreements,” and any implementing regulations issued by the awarding agency. Contractor agrees to be wholly compliant with the provisions of 2 CFR 200, Appendix II.

Additionally, for work to be performed under the Master Agreement or subcontract thereof, including procurement of materials or leases of equipment, Contractor shall notify each potential subcontractor or supplier of the Contractor's federal compliance obligations. These may include, but are not limited to: (a) Title VI of the Civil Rights Act of 1964 (P.L. 88-352) which prohibits discrimination on the basis of race, color or national origin; (b) DocuSign Envelope ID: E4D77477-E07A-45AE-A42F-916BF5C46EDC

Page 9 of 13 ends

Title IX of the Education Amendments of 1972, as amended (20 U.S.C. §§ 1681-1683, and 1685-1686), which prohibits discrimination on the basis of sex; (c) the Fair Labor Standards Act of 1938 (29 USC 676 et. seq.), (d) Section 504 of the Rehabilitation Act of 1973, as amended (29 U.S.C. § 794), which prohibits discrimination on the basis of handicaps and the Americans with Disabilities Act of 1990; (e) the Age Discrimination in Employment Act of 1967 (29 USC 621 et. seq.) and the Age Discrimination Act of 1974, as amended (42 U.S.C. §§ 6101-6107), which prohibits discrimination on the basis of age; (f) the Drug Abuse Office and Treatment Act of 1972 (P.L. 92- 255), as amended, relating to nondiscrimination on the basis of drug abuse; (g) the Comprehensive Alcohol Abuse and Alcoholism Prevention, Treatment and Rehabilitation Act of 1970 (P.L. 91-616), as amended, relating to the nondiscrimination on the basis of alcohol abuse or alcoholism; (h) §§ 523 and 527 of the Public Health Service Act of 1912 (42 U.S.C. 290 dd-3 and 290 ee-3), as amended, relating to confidentiality of alcohol and drug abuse patient records; (i) Title VIII of the Civil Rights Act of 1968 (42 U.S.C. § 3601 et seq.), as amended, relating to nondiscrimination in the sale, rental or financing of housing; (j) any other nondiscrimination provisions in any specific statute(s) applicable to any Federal funding for this Master Agreement; (k) the requirements of any other nondiscrimination statute(s) which may apply to this Master Agreement; (l) applicable provisions of the Clean Air Act (42 U.S.C. §7401 et seq.), the Federal Water Pollution Control Act, as amended (33 U.S.C. §1251 et seq.), Section 508 of the Clean Water Act (33 U.S.C. 1368), Executive Order 11738, and the Environmental Protection Agency regulations at 40 CPR Part 15; (m) applicable provisions of the Davis Bacon Act (40 U.S.C. 276a - 276a- 7), the Copeland Act (40 U.S.C. 276c), and the Contract Work Hours and Safety Standards Act (40 U.S.C. 327- 332), as set forth in Department of Labor Regulations at 20 CPR 5.5a; (n) the mandatory standards and policies relating to energy efficiency which are contained in the state energy conservation plan issued in compliance with the Energy Policy and Conservation Act (P.L. 94-163).

ARTICLE 34: PROHIBITION ON CONTRACTING WITH ENTITIES USING CERTAIN TELECOMMUNICATIONS AND VIDEO SURVEILLANCE EQUIPMENT (EFFECTIVE AUG. 13, 2020 AND AS AMENDED OCTOBER 26, 2020)
Pursuant to 2 CFR 200.216, Contractor shall not offer equipment, services, or system that use covered telecommunications equipment or services as a substantial or essential component of any system, or as critical technology as part of any system. Covered telecommunications equipment or services means 1) telecommunications equipment produced by Huawei Technologies Company or ZTE Corporation (or any subsidiary or affiliate of such entities); 2) for the purpose of public safety, security of government facilities, physical security surveillance of critical infrastructure, and other national security purposes, video surveillance and telecommunications equipment produced by Hytera Communications Corporation, Hangzhou Hikvision Digital Technology Company, or Dahua Technology Company (or any subsidiary or affiliate of such entities); 3) telecommunications or video surveillance services provided by such entities or using such equipment; or 4) telecommunications or video surveillance equipment or services produced or provided by an entity that the Secretary of Defense, in consultation with the Director of National Intelligence or the Director of the Federal Bureau of Investigation, reasonably believes to be an entity owned or controlled by, or otherwise connected to, the government of a covered foreign country. Respondent must comply with requirements for certifications. The provision at 48 C.F.R Section 52.204-26 requires that offerors review SAM prior to completing their required representations. This rule applies to all acquisitions, including acquisitions at or below the simplified acquisition threshold and to acquisitions of commercial items, including commercially available off the-shelf items.

ARTICLE 35: DOMESTIC PREFERENCE
In accordance with 2 CFR 200.322, as appropriate and to the extent consistent with law, when using federal grant award funds H-GAC should, to the greatest extent practicable, provide a preference for the purchase, acquisition, or use of goods, products, or materials produced in the United States (including but not limited to iron, aluminum, steel, cement, and other manufactured products). H-GAC must include this requirement in all subawards including all contracts and purchase orders for work or products under the federal grant award. If Contractor intends to qualify for Purchase Orders using federal grant money, then it shall work with H-GAC to provide all required certifications and other documentation needed to show compliance.

ARTICLE 36: CRIMINAL PROVISIONS AND SANCTIONS
The Contractor agrees to perform the Master Agreement in conformance with safeguards against fraud and abuse as set forth by the H-GAC, the State of Texas, and the acts and regulations of any related state or federal agency.

The Contractor agrees to promptly notify H-GAC of any actual or suspected fraud, abuse, or other criminal activity DocuSign Envelope ID: E4D77477-E07A-45AE-A42F-916BF5C46EDC

Page 10 of 13 ends

through the filing of a written report within twenty-four (24) hours of knowledge thereof. Contractor shall notify H-GAC of any accident or incident requiring medical attention arising from its activities under this Master Agreement within twenty-four (24) hours of such occurrence. Theft or willful damage to property on loan to the Contractor from H-GAC, if any, shall be reported to local law enforcement agencies and H-GAC within two (2) hours of discovery of any such act.

The Contractor further agrees to cooperate fully with H-GAC, local law enforcement agencies, the State of Texas, the Federal Bureau of Investigation, and any other duly authorized investigative unit, in carrying out a full investigation of all such incidents.

The Contractor shall notify H-GAC of the threat of lawsuit or of any actual suit filed against the Contractor pertaining to this Master Agreement or which would adversely affect the Contractor’s ability to perform services under this Master Agreement.

ARTICLE 37: INDEMNIFICATION AND RECOVERY
H-GAC’s liability under this Master Agreement, whether for breach of contract, warranty, negligence, strict liability, in tort or otherwise, is limited to its order processing charge. In no event will H-GAC be liable for any loss of use, loss of time, inconvenience, commercial loss, lost profits, or savings or other incidental, special or consequential damages to the full extent such use may be disclaimed by law. Contractor agrees, to the extent permitted by law, to defend and hold harmless H-GAC, its board members, officers, agents, officials, employees, and indemnities from any and all claims, costs, expenses (including reasonable attorney fees), actions, causes of action, judgements, and liens arising as a result of Contractor’s negligent act or omission under this Master Agreement. Contractor shall notify H-GAC of the threat of lawsuit or of any actual suit filed against Contractor relating to this Master Agreement.

ARTICLE 38: LIMITATION OF CONTRACTOR’S LIABILITY
Except as specified in any separate writing between the Contractor and an END USER, Contractor’s total liability under this Master Agreement, whether for breach of contract, warranty, negligence, strict liability, in tort or otherwise, but excluding its obligation to indemnify H-GAC, is limited to the price of the particular products/services sold hereunder, and Contractor agrees either to refund the purchase price or to repair or replace product(s) that are not as warranted. In no event will Contractor be liable for any loss of use, loss of time, inconvenience, commercial loss, loss of profits or savings or other incidental, special or consequential damages to the full extent such use may be disclaimed by law. Contractor understands and agrees that it shall be liable to repay and shall repay upon demand to END USER any amounts determined by H-GAC, its independent auditors, or any agency of State or Federal government to have been paid in violation of the terms of this Master Agreement.

ARTICLE 39: TITLES NOT RESTRICTIVE
The titles assigned to the various Articles of this Master Agreement are for convenience only. Titles shall not be considered restrictive of the subject matter of any Article, or part of this Master Agreement.

ARTICLE 40: JOINT WORK PRODUCT
This Master Agreement is the joint work product of H-GAC and the Contractor. This Master Agreement has been negotiated by H-GAC and the Contractor and their respective counsel and shall be fairly interpreted in accordance with its terms and, in the event of any ambiguities, no inferences shall be drawn against any party.

ARTICLE 41: PROCUREMENT OF RECOVERED MATERIAL
H-GAC and the Respondent must comply with section 6002 of the Solid Waste Disposal Act, as amended by the Resource Conservation and Recovery Act. The requirements of Section 6002 include: (1) procuring only items designated in guidelines of the Environmental Protection Agency (EPA) at 40 CFR part 247 that contain the highest percentage of recovered materials practicable, consistent with maintaining a satisfactory level of competition, where the purchase price of the item exceeds $10,000 or the value of the quantity acquired during the preceding fiscal year exceeded $10,000; (2) procuring solid waste management services in a manner that maximizes energy and resource recovery; and (3) establishing an affirmative procurement program for procurement of recovered materials identified in the EPA guidelines. Pursuant to the Federal Rule above, as required by the Resource Conservation and Recovery Act of 1976 (42 U.S.C. § 6962(c)(3)(A)(i)), Respondent DocuSign Envelope ID: E4D77477-E07A-45AE-A42F-916BF5C46EDC

Page 11 of 13 ends

certifies that the percentage of recovered materials content for EPA-designated items to be delivered or used in the performance of the Contract will be at least the amount required by the applicable contract specifications or other contractual requirements.

ARTICLE 42: COPELAND “ANTI-KICKBACK” ACT
Contractor shall comply with 18 U.S.C. § 874, 40 U.S.C. § 3145, and the requirements of 29 C.F.R. pt. 3 as may be applicable, which are incorporated by reference into the contract. The contractor or subcontractor shall insert in any subcontracts the clause above and such other clauses as appropriate agency instructions require, and also a clause requiring the subcontractors to include these clauses in any lower tier subcontracts. The prime contractor shall be responsible for the compliance by any subcontractor or lower tier subcontractor with all of these contract clauses. A breach of the contract clauses above may be grounds for termination of the Contract, and for debarment as a contractor and subcontractor as provided in 29 C.F.R. § 5.12.

ARTICLE 43: DISCRIMINATION
Respondent and any potential subcontractors shall comply with all Federal statutes relating to nondiscrimination.

These include, but are not limited to:

a) Title VI of the Civil Rights Act of 1964 (P.L. 88-352), which prohibits discrimination on the basis of race, color, or national origin;
b) Title IX of the Education Amendments of 1972, as amended (20 U.S.C. §§1681-1683, and 1685-1686), which prohibits discrimination on the basis of sex;
c) Section 504 of the Rehabilitation Act of 1973, as amended (29 U.S.C. §794), which prohibits discrimination on the basis of handicaps;
d) The Age Discrimination Act of 1975, as amended (42 U.S.C. §§6101- 6107), which prohibits discrimination on the basis of age;
e) The Drug Abuse Office and Treatment Act of 1972 (P.L. 92-255), as amended, relating to nondiscrimination on the basis of drug abuse;
f) The Comprehensive Alcohol Abuse and Alcoholism Prevention, Treatment and Rehabilitation Act of 1970 (P.L. 91-616), as amended, relating to nondiscrimination on the basis of alcohol abuse or alcoholism;
g) Sections 523 and 527 of the Public Health Service Act of 1912 (42 U.S.C. §§290 dd-3 and 290 ee-3), as amended, relating to confidentiality of alcohol and drug abuse patient records; h) Title VIII of the Civil Rights Act of 1968 (42 U.S.C. §§3601 et seq.), as amended, relating to nondiscrimination in the sale, rental, or financing of housing; i) Any other nondiscrimination provisions in the specific statute(s) under which application for Federal assistance is being made; and
j) The requirements of any other nondiscrimination statute(s) that may apply to the application.

ARTICLE 44: DRUG FREE WORKPLACE
Contractor must provide a drug-free workplace in accordance with the Drug-Free Workplace Act, as applicable.

For the purposes of this Section, “drug-free” means a worksite at which employees are prohibited from engaging in the unlawful manufacture, distribution, dispensation, possession, or use of a controlled substance. H-GAC may request a copy of this policy.

ARTICLE 45: APPLICABILITY TO SUBCONTRACTORS
Respondent agrees that all contracts it awards pursuant to the contract awarded as a result of this Master Agreement will be bound by the foregoing terms and conditions.

ARTICLE 46: WARRANTY AND COPYRIGHT
Submissions must include all warranty information, including items covered, items excluded, duration, and renewability. Submissions must include proof of licensing if using third party code for programming.

ARTICLE 47: DATA HANDLING AND SECURITY
It will always be the responsibility of the selected Contractor to manage data transfer and to secure all data appropriately during the project to prevent unauthorized access to all data, products, and deliverables.

DocuSign Envelope ID: E4D77477-E07A-45AE-A42F-916BF5C46EDC

Page 12 of 13 ends

ARTICLE 48: DISPUTES
All disputes concerning questions of fact or of law arising under this Master Agreement, which are not addressed within the Whole Master Agreement as defined pursuant to Article 4 hereof, shall be decided by the Executive Director of H-GAC or his designee, who shall reduce his decision to writing and provide notice thereof to the Contractor. The decision of the Executive Director or his designee shall be final and conclusive unless, within thirty (30) days from the date of receipt of such notice, the Contractor requests a rehearing from the Executive Director of H-GAC. In connection with any rehearing under this Article, the Contractor shall be afforded an opportunity to be heard and offer evidence in support of its position. The decision of the Executive Director after any such rehearing shall be final and conclusive. The Contractor may, if it elects to do so, appeal the final and conclusive decision of the Executive Director to a court of competent jurisdiction. Pending final decision of a dispute hereunder, the Contractor shall proceed diligently with the performance of the Master Agreement and in accordance with HGAC's final decision.

ARTICLE 49: CHOICE OF LAW: VENUE
This Master Agreement shall be governed by the laws of the State of Texas. Venue and jurisdiction of any suit or cause of action arising under or in connection with the Master Agreement shall lie exclusively in Harris County, Texas. Disputes between END USER and Contractor are to be resolved in accordance with the law and venue rules of the state of purchase. Contractor shall immediately notify H-GAC of such disputes.

ARTICLE 50: ORDER OF PRIORITY
In the case of any conflict between or within this Master Agreement, the following order of priority shall be utilized: 1) General Provisions, 2) Special Provisions, 3) Scope of Work, and 4) Other Attachments.

ARTICLE 51: WHOLE MASTER AGREEMENT
Please note, this is an H-GAC Master Agreement template and is used for all products and services offered in H-GAC Cooperative Purchasing. Any redlines to this Master Agreement may not be reviewed. If this Master Agreement has not been signed by the Contractor within 30 calendar days, this Master Agreement will be automatically voided. The Master General Provisions, Master Special Provisions, and Attachments, as provided herein, constitute the complete Master Agreement between the parties hereto, and supersede any and all oral and written Master Agreements between the parties relating to matters herein. Except as otherwise provided herein, this Master Agreement cannot be modified without written consent of the parties.

ARTICLE 52: UNIVERSAL IDENTIFIER AND SYSTEM FOR AWARD MANAGEMENT (SAM) In accordance with 2 CFR Title 2, Subtitle A, Chapter I, Part 25 as it applies to a Federal awarding agency's grants, cooperative agreements, loans, and other types of Federal financial assistance as defined in 2 CFR 25.406.

Contractor understands and as it relates to 2 CFR 25.205(a), a Federal awarding agency may not make a Federal award or financial modification to an existing Federal award to an applicant or recipient until the entity has complied with the requirements described in 2 CFR 25.200 to provide a valid unique entity identifier and maintain an active SAM registration (www.SAM.gov) with current information (other than any requirement that is not applicable because the entity is exempted under § 25.110). 2 CFR 25.200(b) requires that registration in the SAM prior to submitting an application or plan; and maintain an active SAM registration with current information, including information on a recipient's immediate and highest level owner and subsidiaries, as well as on all predecessors that have been awarded a Federal contract or grant within the last three years, if applicable, at all times during which it has an active Federal award or an application or plan under consideration by a Federal awarding agency; and provide its unique entity identifier in each application or plan it submits to the Federal awarding agency. To remain registered in the SAM database after the initial registration, the applicant is required to review and update its information in the SAM database on an annual basis from the date of initial registration or subsequent updates to ensure it is current, accurate and complete. At the time a Federal awarding agency is ready to make a Federal award, if the intended recipient has not complied with an applicable requirement to provide a unique entity identifier or maintain an active SAM registration with current information, the Federal awarding agency: (1) May determine that the applicant is not qualified to receive a Federal award; and (2) May use that determination as a basis for making a Federal award to another applicant.

ARTICLE 53: PROCUREMENT OF RECOVERED MATERIALS
DocuSign Envelope ID: E4D77477-E07A-45AE-A42F-916BF5C46EDC

Page 13 of 13 ends

In accordance with 2 CFR 200.323, the Houston-Galveston Area Council and the Contractor or Subrecipient must comply with section 6002 of the Solid Waste Disposal Act, as amended by the Resource Conservation and Recovery Act. The requirements of Section 6002 include: (1) procuring only items designated in guidelines of the Environmental Protection Agency (EPA) at 40 CFR part 247 that contain the highest percentage of recovered materials practicable, consistent with maintaining a satisfactory level of competition, where the purchase price of the item exceeds $10,000 or the value of the quantity acquired during the preceding fiscal year exceeded $10,000; (2) procuring solid waste management services in a manner that maximizes energy and resource recovery; and (3) establishing an affirmative procurement program for procurement of recovered materials identified in the EPA guidelines. Pursuant to the Federal Rule above, as required by the Resource Conservation and Recovery Act of 1976 (42 U.S.C. § 6962(c)(3)(A)(i)), the Contractor or Subrecipient certifies that the percentage of recovered materials content for EPA-designated items to be delivered or used in the performance of the Agreement will be at least the amount required by the applicable contract specifications or other contractual requirements.

SIGNATURES:

H-GAC and the Contractor have read, agreed, and executed the whole Master Agreement as of the date first written above, as accepted by:

Braun Northwest, Inc.

Signature $docusign:SignHere::Customer1

Name Tami McCallum

Title V.P. Sales

Date $docusign:DateSigned::Customer1

H-GAC

Signature $docusign:SignHere::InternalSigner

Name Chuck Wemple

Title Executive Director

Date $docusign:DateSigned::InternalSigner

DocuSign Envelope ID: E4D77477-E07A-45AE-A42F-916BF5C46EDC 10/16/2023
10/23/2023
H-GAC
Houston-Galveston Area Council
P.O. Box 22777 · 3555 Timmons · Houston, Texas 77227-2777 Cooperative Agreement - Contract - Braun Northwest, Inc. - Public Services - ID: 11091

Page 1 of 8 ends

MASTER SPECIAL PROVISIONS

Please note, this is an H-GAC Master Agreement template and is used for all products and services offered in H-GAC Cooperative Purchasing. Any redlines to this Master Agreement may not be reviewed.

Incorporated by attachment, as part of the whole Master Agreement, H-GAC and the Contractor do, hereby agree to the Master Special Provisions as follows:

ARTICLE 1: BIDS/PROPOSALS INCORPORATED
In addition to the whole Master Agreement, the following documents listed in order of priority are incorporated into the Master Agreement by reference: Bid/Proposal Specifications and Contractor’s Response to the Bid/Proposal.

ARTICLE 2: END USER MASTER AGREEMENTS (“EUA”)
H-GAC acknowledges that the END USER, which is the HGACBuy customer utilizing the contract (CUSTOMER and END USER may be used interchangeably) may choose to enter into an End User Master Agreement (EUA) with the Contractor through this Master Agreement. A CUSTOMER/END USER is a state agency, county, municipality, special district, or other political subdivision of a state, or a qualifying non-profit corporation (providing one or more governmental function or service that possess legal authority to enter into the Contract. The term of the EUA may exceed the term of the current H-GAC Master Agreement.

H-GAC’s acknowledgement is not an endorsement or approval of the End User Master Agreement’s terms and conditions. Contractor agrees not to offer, agree to or accept from the CUSTOMER/END USER, any terms or conditions that conflict with those in Contractor’s Master Agreement with H-GAC. Contractor affirms that termination of its Master Agreement with H-GAC for any reason shall not result in the termination of any underlying EUA, which shall in each instance, continue pursuant to the EUA’s stated terms and duration.

Pursuant to the terms of this Master Agreement, termination of this Master Agreement will disallow the Contractor from entering into any new EUA with CUSTOMER/END USER. Applicable H-GAC order processing charges will be due and payable to H-GAC on any EUAs, surviving termination of this Master Agreement between H-GAC and Contractor.

ARTICLE 3: MOST FAVORED CUSTOMER CLAUSE
Contractor shall provide its most favorable pricing and terms to H-GAC. If at any time during this Master Agreement, Contractor develops a regularly followed standard procedure of entering into Master Agreements with other governmental customers within the State of Texas, and offers the same or substantially the same products/services offered to H-GAC on a basis that provides prices, warranties, benefits, and or terms more favorable than those provided to H-GAC, Contractor shall notify H-GAC within ten (10) business days thereafter, and this Master Agreement shall be deemed to be automatically retroactively amended, to the effective date of Contractor’s most favorable past Master Agreement with another entity. Contractor shall provide the same prices, warranties, benefits, or terms to H-GAC and its CUSTOMER/END USER as provided in its most favorable past Master Agreement. H-GAC shall have the right and option at any time to decline to accept any such change, in which case the amendment shall be deemed null and void. If Contractor claims that a more favorable price, warranty, benefit, or term that was charged or offered to another entity during the term of this Master Agreement, does not constitute more favorable treatment, than Contractor shall, within ten (10) business days, notify H-GAC in writing, setting forth the detailed reasons Contractor believes the aforesaid DocuSign Envelope ID: E4D77477-E07A-45AE-A42F-916BF5C46EDC

Page 2 of 8 ends

offer is not in fact most favored treatment. H-GAC, after due consideration of Contractor’s written explanation, may decline to accept such explanation and thereupon this Master Agreement between H-GAC and Contractor shall be automatically amended, effective retroactively, to the effective date of the most favored Master Agreement, to provide the same prices, warranties, benefits, or terms to H-GAC and the CUSTOMER/END USER.

EXCEPTION: This clause shall not be applicable to prices and price adjustments offered by a bidder, proposer, or contractor, which are not within bidder's/proposer’s control [example; a manufacturer's bid concession], or to any prices offered to the Federal Government and its agencies.

ARTICLE 4: PARTY LIABILITY
Contractor’s total liability under this Master Agreement, whether for breach of contract, warranty, negligence, strict liability, in tort or otherwise, is limited to the price of the particular products/services sold hereunder.

Contractor agrees either to refund the purchase price or to repair or replace product(s) that are not as warranted.

Contractor accepts liability to repay, and shall repay upon demand to CUSTOMER/END USER, any amounts determined by H-GAC, its independent auditors, or any state or federal agency, to have been paid in violation of the terms of this Master Agreement.

ARTICLE 5: GOVERNING LAW & VENUE
Contractor and H-GAC agree that Contractor will make every reasonable effort to resolve disputes with the CUSTOMER/END USER in accord with the law and venue rules of the state of purchase. Contractor shall immediately notify H-GAC of such disputes.

ARTICLE 6: SALES AND ORDER PROCESSING CHARGE
Contractor shall sell its products to CUSTOMER/END USER based on the pricing and terms of this Master Agreement. H-GAC will invoice Contractor for the applicable order processing charge when H-GAC receives notification of a CUSTOMER/END USER order. Contractor shall remit to H-GAC the full amount of the applicable order processing charge, after delivery of any product or service and subsequent CUSTOMER/END USER acceptance. Payment of the Order Processing Charge shall be remitted from Contractor to H-GAC, within thirty (30) calendar days or ten (10) business days after receipt of a CUSTOMER/END USER’s payment, whichever comes first, notwithstanding Contractor’s receipt of invoice. For sales made by Contractor based on this Master Agreement, including sales to entities without Interlocal Master Agreements, Contractor shall pay the applicable order processing charges to H-GAC. Further, Contractor agrees to encourage entities who are not members of H-GAC’s Cooperative Purchasing Program to execute an H-GAC Interlocal Master Agreement. H-GAC reserves the right to take appropriate actions including, but not limited to, Master Agreement termination if Contractor fails to promptly remit the appropriate order processing charge to H-GAC.

In no event shall H-GAC have any liability to Contractor for any goods or services a CUSTOMER/END USER procures from Contractor. At all times, Contractor shall remain liable to pay to H-GAC any order processing charges on any portion of the Master Agreement actually performed, and for which compensation was received by Contractor.

ARTICLE 7: LIQUIDATED DAMAGES
Contractor and H-GAC agree that Contractor shall cooperate with the CUSTOMER/END USER at the time a CUSTOMER/END USER purchase order is placed, to determine terms for any liquidated damages.

ARTICLE 8: INSURANCE
Unless otherwise stipulated in Section B of the Bid/Proposal Specifications, Contractor must have the following insurance and coverage minimums:

DocuSign Envelope ID: E4D77477-E07A-45AE-A42F-916BF5C46EDC

Page 3 of 8 ends

a. General liability insurance with a Single Occurrence limit of at least $1,000,000.00, and a General Aggregate limit of at least two times the Single Occurrence limit. b. Product liability insurance with a Single Occurrence limit of at least $1,000,000.00, and a General Aggregate limit of at least two times the Single Occurrence limit for all Products except Automotive Fire Apparatus. For Automotive Fire Apparatus, see Section B of the Bid/Proposal Specifications. c. Property Damage or Destruction insurance is required for coverage of End User owned equipment while in Contractor's possession, custody, or control. The minimum Single Occurrence limit is $500,000.00 and the General Aggregate limit must be at least two times the Single Occurrence limit. This insurance may be carried in several ways, e.g. under an Inland Marine policy, as art of Automobile coverage, or under a Garage Keepers policy. In any event, this coverage must be specifically and clearly listed on insurance certificate(s) submitted to H-GAC.
d. Insurance coverage shall be in effect for the length of any contract made pursuant to the Bid/Proposal, and for any extensions thereof, plus the number of days/months required to deliver any outstanding order after the close of the contract period.
e. Original Insurance Certificates must be furnished to H-GAC on request, showing Contractor as the insured and showing coverage and limits for the insurances listed above. f. If any Product(s) or Service(s) will be provided by parties other than Contractor, all such parties are required to carry the minimum insurance coverages specified herein, and if requested by H-GAC, a separate insurance certificate must be submitted for each such party. g. H-GAC reserves the right to contact insurance underwriters to confirm policy and certificate issuance and document accuracy.

ARTICLE 9: PERFORMANCE AND PAYMENT BONDS FOR INDIVIDUAL ORDERS H-GAC’s contractual requirements DO NOT include a Performance & Payment Bond (PPB); therefore, Contractor shall offer pricing that reflects this cost savings. Contractor shall remain prepared to offer a PPB to cover any order if so requested by the CUSTOMER/ END USER. Contractor shall quote a price to CUSTOMER/ END USER for provision of any requested PPB, and agrees to furnish the PPB within ten business (10) days of receipt of CUSTOMER/END USER's purchase order.

ARTICLE 10: ORDER PROCESSING CHARGE
H-GAC will apply an Order Processing Charge for each sale done through the H-GAC contract, with the exception of orders for motor vehicles. Any pricing submitted must include this charge amount per the most current H-GAC schedule. For motor vehicle orders, the Processing Charge is paid by the CUSTOMER/END USER. Contractor will need to refer to the solicitation for the Order Processing Charge.

ARTICLE 11: CHANGE OF STATUS
Contractor shall immediately notify H-GAC, in writing, of ANY change in ownership, control, dealership/franchisee status, Motor Vehicle license status, or name. Contractor shall offer written guidance to advise H-GAC if this Master Agreement shall be affected in any way by such change. H-GAC shall have the right to determine whether or not such change is acceptable, and to determine what action shall be warranted, up to and including cancellation of Master Agreement.

ARTICLE 12: REQUIREMENTS TO APPLICABLE PHYSICAL GOODS
In the case of physical goods (e.g. equipment, material, supplies, as opposed to services), all Products offered must comply with any applicable provisions of the Texas Business and Commerce Code, Title 1, Chapter 2 and with at least the following:

DocuSign Envelope ID: E4D77477-E07A-45AE-A42F-916BF5C46EDC

Page 4 of 8 ends

a. Be new, unused, and not refurbished.
b. Not be a prototype as the general design, operation, and performance. This requirement is NOT meant to preclude the Contractor from offering new models or configurations which incorporate improvements in a current design or add functionality, but in which new model or configuration may be new to the marketplace.
c. Include all accessories which may or may not be specifically mentioned in the Master Agreement, but which are normally furnished or necessary to make the Product ready for its intended use upon delivery.

Such accessories shall be assembled, installed, and adjusted to allow continuous operation of Product at time of delivery.
d. Have assemblies, sub-assemblies and component parts that are standard and interchangeable throughout the entire quantity of a Product as may be purchased simultaneously by any END USER/CUSTOMER. e. Be designed and constructed using current industry accepted engineering and safety practices, and materials.
f. Be available for inspection at any time prior to or after procurement.

ARTICLE 13: TEXAS MOTOR VEHICLE BOARD LICENSING
All Contractors that deal in motor vehicles shall maintain current licenses that are required by the Texas Motor Vehicle Commission Code. If at any time during this Master Agreement term, any required Contractor license is denied, revoked, or not renewed, Contractor shall be in default of this Master Agreement, unless the Texas Motor Vehicle Board issues a stay or waiver. Contractor shall promptly provide copies of all current applicable Texas Motor Vehicle Board documentation to H-GAC upon request.

ARTICLE 14: INSPECTION/TESTING
All Products sold pursuant to this Master Agreement will be subject to inspection/testing by or at the direction of H-GAC and/or the ordering CUSTOMER/END USER, either at the delivery destination or the place of manufacture. In the event a Product fails to meet or exceed all requirements of this Master Agreement, and unless otherwise agreed in advance, the cost of any inspection and/or testing, will be the responsibility of the Contractor.

ARTICLE 15: ADDITIONAL REPORTING REQUIREMENTS
Contractor agrees to submit written quarterly reports to H-GAC detailing all transactions during the previous three (3) month period. Reports must include, but are not limited, to the following information:
a. CUSTOMER/END USER Name
b. Product/Service purchased, including Product Code if applicable c. Customer Purchase Order Number
d. Purchase Order Date
e. Product/Service dollar amount
f. HGACBuy Order Processing Charge amount

ARTICLE 16: BACKGROUND CHECKS
Cooperative customers may request background checks on any awarded contractor’s employees who will have direct contact with students, or for any other reason they so choose, any may require contractor to pay the cost of obtaining any background information requested by the CUSTOMER/END USER.

ARTICLE 17: PROHIBITION ON CONTRACTS WITH COMPANIES BOYCOTTING ISRAEL

CERTIFICATION
As required by Chapter 2271 of the Texas Local Government Code the Contractor must verify that it 1) does not boycott Israel; and 2) will not boycott Israel during the term of the Contract. Pursuant to Section 2271.001, Texas Government Code:

DocuSign Envelope ID: E4D77477-E07A-45AE-A42F-916BF5C46EDC

Page 5 of 8 ends

1. “Boycott Israel” means refusing to deal with, terminating business activities with, or otherwise taking any action that is intended to penalize, inflict economic harm on, or limit commercial relations specifically with Israel, or with a person or entity doing business in Israel or in an Israeli-controlled territory, but does not include an action made for ordinary business purposes; and

2. “Company” means a for-profit sole proprietorship, organization, association, corporation, partnership, joint venture, limited partnership, limited liability partnership, or any limited liability company, including a wholly owned subsidiary, majority-owned subsidiary, parent company or affiliate of those entities or business associations that exist to make a profit.

ARTICLE 18: NO EXCLUDED NATION OR TERRORIST ORGANIZATION CERTIFICATION As required by Chapter 2252 of the Texas Government Code the Contractor must certify that it is not a company engaged in active business operations with Sudan, Iran, or a foreign terrorist organization – specifically, any company identified on a list prepared and maintained by the Texas Comptroller under Texas Government Code §§806.051, 807.051, or 2252.153. (A company that the U.S. Government affirmatively declares to be excluded from its federal sanctions regime relating to Sudan, Iran, or any federal sanctions regime relating to a foreign terrorist organization is not subject to the contract prohibition.)

ARTICLE 19: PROHIBITION ON CONTRACTING WITH ENTITIES USING CERTAIN TELECOMMUNICATIONS AND VIDEO SURVEILLANCE EQUIPMENT (Effective Aug. 13, 2020 and as amended October 26, 2020)
Pursuant to 2 CFR 200.216, Contractor shall not offer equipment, services, or system that use covered telecommunications equipment or services as a substantial or essential component of any system, or as critical technology as part of any system. ‘‘Covered telecommunications equipment or services means 1) telecommunications equipment produced by Huawei Technologies Company or ZTE Corporation (or any subsidiary or affiliate of such entities); 2) for the purpose of public safety, security of government facilities, physical security surveillance of critical infrastructure, and other national security purposes, video surveillance and telecommunications equipment produced by Hytera Communications Corporation, Hangzhou Hikvision Digital Technology Company, or Dahua Technology Company (or any subsidiary or affiliate of such entities); 3) telecommunications or video surveillance services provided by such entities or using such equipment; or 4) telecommunications or video surveillance equipment or services produced or provided by an entity that the Secretary of Defense, in consultation with the Director of National Intelligence or the Director of the Federal Bureau of Investigation, reasonably believes to be an entity owned or controlled by, or otherwise connected to, the government of a covered foreign country.

Contractor must comply with requirements for certifications. The provision at 48 C.F.R Section 52.204-26 requires that Contractors review SAM prior to completing their required representations. This rule applies to all acquisitions, including acquisitions at or below the simplified acquisition threshold and to acquisitions of commercial items, including commercially available off the-shelf items.

ARTICLE 20: BUY AMERICA ACT (National School Lunch Program and Breakfast Program) With respect to products purchased by CUSTOMER/END USER for use in the National School Lunch Program and/or National School Breakfast Program, Contractor shall comply with all federal procurement laws and regulations with respect to such programs, including the Buy American provisions set forth in 7 C.F.R. Part 210.21(d), to the extent applicable. Contractor agrees to provide all certifications required by CUSTOMER/END USER regarding such programs.

In the event Contractor or Contractor’s supplier(s) are unable or unwilling to certify compliance with the Buy American Provision, or the applicability of an exception to the Buy American provision, H-GAC CUSTOMER/END USER may decide not to purchase from Contractor. Additionally, H-GAC DocuSign Envelope ID: E4D77477-E07A-45AE-A42F-916BF5C46EDC

Page 6 of 8 ends

CUSTOMER/END USER may require country of origin on all products and invoices submitted for payment by Contractor, and Contractor agrees to comply with any such requirement.

ARTICLE 21: BUY AMERICA REQUIREMENT (Applies only to Federally Funded Highway and Transit Projects)
With respect to products purchased by CUSTOMER/END USER for use in federally funded highway projects, Contractor shall comply with all federal procurement laws and regulations with respect to such projects, including the Buy American provisions set forth in 23 U.S.C. Section 313, 23 C.F.R. Section 635.410, as amended, and the Steel and Iron Preference provisions of Texas Transportation Code Section 223.045, to the extent applicable. Contractor agrees to provide all certifications required by CUSTOMER/END USER regarding such programs. With respect to products purchased by CUSTOMER/END USER for use in federally funded transit projects, Contractor shall comply with all federal procurement laws and regulations with respect to such projects, including the Buy American provisions set forth in 49 U.S.C. Section 5323(j)(1), 49 C.F.R.

Sections 661.6 or 661.12, to the extent applicable. Contractor agrees to provide all certifications required by CUSTOMER/END USER regarding such programs.

ARTICLE 22: DOMESTIC PREFERENCE
In accordance with 2 CFR 200.322, as appropriate and to the extent consistent with law, a CUSTOMER/END USER using federal grant award funds should, to the greatest extent practicable, provide a preference for the purchase, acquisition, or use of goods, products, or materials produced in the United States (including but not limited to iron, aluminum, steel, cement, and other manufactured products). The CUSTOMER/END USER must include this requirement in all subawards including all contracts and purchase orders for work or products under the federal grant award. If Contractor intends to qualify for Purchase Orders using federal grant money, they shall work with the CUSTOMER/END USER to provide all required certifications and other documentation needed to show compliance.

ARTICLE 23: TITLE VI REQUIREMENTS
H-GAC in accordance with the provisions of Title VI of the Civil Rights Act of 1964 (78 Stat. 252, 42 U.S.C. §§ 2000d to 2000d-4) and the Regulations, hereby notifies all bidders that it will affirmatively ensure that any disadvantaged business enterprises will be afforded full and fair opportunity to submit in response to this Master Agreement and will not be discriminated against on the grounds of race, color, or national origin in consideration for an award.

ARTICLE 24: EQUAL EMPLOYMENT OPPORTUNITY
Except as otherwise provided under 41 CFR Part 60, all Contracts and CUSTOMER/END USER Purchase Orders that meet the definition of “federally assisted construction contract” in 41 CFR Part 60-1.3 shall be deemed to include the equal opportunity clause provided under 41 CFR 60-1.4(b), in accordance with Executive Order 11246, “Equal Employment Opportunity” (30 FR 12319, 12935, 3 CFR Part, 1964-1965 Comp., pg.339), as amended by Executive Order 11375, “Amending Executive Order 11246 Relating to Equal Employment Opportunity,” and implementing regulations at 41CFR Part 60, “Office of Federal Contract Compliance Programs, Equal Employment Opportunity, Department of Labor.”

The equal opportunity clause provided under 41 CFR 60-1.4(b) is hereby incorporated by reference. Contractor agrees that such provision applies to any contract that meets the definition of “federally assisted construction contract” in 41 CFR Part 60-1.3 and agrees that it will comply with such provision.

ARTICLE 25: CLEAN AIR AND WATER POLLUTION CONTROL ACT
CUSTOMER/END USER Purchase Orders using federal funds must contain a provision that requires the Contractor to agree to comply with all applicable standards, orders or regulations issued pursuant to the Clean DocuSign Envelope ID: E4D77477-E07A-45AE-A42F-916BF5C46EDC

Page 7 of 8 ends

Air Act (42 U.S.C. 7401-7671q) and the Federal Water Pollution Control Act as amended (33 U.S.C. 1251- 1387). Violations must be reported to the Federal awarding agency and the Regional Office of the Environmental Protection Agency (EPA).

Pursuant to the Federal Rule above, Contractor certifies that it is in compliance with all applicable provisions of the Clean Air Act (42 U.S.C. 7401-7671q) and the Federal Water Pollution Control Act as amended (33 U.S.C. 1251-1387) and will remain in compliance during the term of the Contract.

ARTICLE 26: PREVAILING WAGE
Contractor and any potential subcontractors have a duty to and shall pay the prevailing wage rate under the Davis-Bacon Act, 40 U.S.C. 276a – 276a-5, as amended, and the regulations adopted thereunder contained in 29 C.F.R. pt. 1 and 5.

ARTICLE 27: CONTRACT WORK HOURS AND SAFETY STANDARDS
As per the Contract Work Hours and Safety Standards Act (40 U.S.C. 3701-3708), where applicable, all CUSTOMER/END USER Purchase Orders in excess of $100,000 that involve the employment of mechanics or laborers must include a provision for compliance with 40 U.S.C. 3702 and 3704, as supplemented by Department of Labor regulations (29 CFR Part 5). Under 40 U.S.C. 3702 of the Act, each contractor must be required to compute the wages of every mechanic and laborer, on the basis of a standard work week of 40 hours. Work in excess of the standard work week is permissible provided that the worker is compensated at a rate of not less than one and a half times the basic rate of pay for all hours worked in excess of 40 hours in the work week. The requirements of 40 U.S.C. 3704 are applicable to construction work and provide that no laborer or mechanic must be required to work in surroundings or under working conditions which are unsanitary, hazardous, or dangerous. These requirements do not apply to the purchases of supplies or materials or articles ordinarily available on the open market, or contracts for transportation or transmission of intelligence.

ARTICLE 28: PROFIT AS A SEPARATE ELEMENT OF PRICE
For purchases using federal funds more than the current Simplified Acquisition Threshold of $250,000, requires negotiation of profit as a separate element of the price. See, 2 CFR 200.324(b). Contractor agrees to provide information and negotiate regarding profit as a separate element of the price for the purchase. Contractor also agrees that the total price, including profit, charged by Contractor will not exceed the awarded pricing, including any applicable discount, under any awarded contract.

ARTICLE 29: BYRD ANTI-LOBBYING AMENDMENT
Byrd Anti-Lobbying Amendment (31U.S.C. 1352) – Contractors that apply or bid for an award exceeding $100,000 must file the required anti-lobbying certification. Each tier must certify to the tier above that it will not and has not used Federal appropriated funds to pay any person or organization for influencing or attempting to influence an officer or employee of any agency, a member of Congress, officer or employee of Congress, or an employee of a member of Congress in connection with obtaining any Federal contract, grant or any other award covered by 31 U.S.C. 1352. Each tier must also disclose any lobbying with non-Federal funds that takes place in connection with obtaining any Federal award. Such disclosures are forwarded from tier to tier, up to the CUSTOMER/END USER. As applicable, Contractor agrees to file all certifications and disclosures required by, and otherwise comply with, the Byrd Anti-Lobbying Amendment (31 USC 1352). Contractor certifies that it is currently in compliance with all applicable provisions of the Byrd Anti-Lobbying Amendment (31 U.S.C. 1352) and will continue to be in compliance throughout the term of the Contract and further certifies that:

1. No Federal appropriated funds have been paid or will be paid by or on behalf of the Contractor, to any person for influencing or attempting to influence an officer or employee of any agency, a Member of Congress, an officer or employee of Congress, or an employee of a Member of Congress in connection DocuSign Envelope ID: E4D77477-E07A-45AE-A42F-916BF5C46EDC

Page 8 of 8 ends

with the awarding of a Federal contract, the making of a Federal Grant, the making of a Federal Loan, the entering into a cooperative Master Agreement, and the extension, continuation, renewal, amendment, or modification of a Federal contract, grant, loan, or cooperative Master Agreement.

2. If any funds other than Federal appropriated funds have been paid or will be paid to any person for influencing, or attempting to influence, an officer or employee of a Member of Congress in connection with a Federal contract, grant, loan, or cooperative Master Agreement, Contractor shall complete and submit Standard Form – LLL, “Disclosure Form to Report Lobbying”, in accordance with its instructions.

3. Contractor shall require that the language of this certification be included in the award documents for all subawards at all tiers (including subcontracts, subgrants, and contracts under grants, loans, and cooperative Master Agreements) and that all subcontractors shall certify and disclose accordingly.

This certification is a material representation of fact upon which reliance was placed when this transaction was made or entered into. Submission of this certificate is a prerequisite for making or entering into this transaction imposed by Section 1352, title 31, U.S. Code. Any person who fails to file the required certification shall be subject to a civil penalty of not less than $10,000 and not more than $100,000 for each such failure.

ARTICLE 30: COMPLIANCE WITH EPA REGULATIONS APPLICABLE TO GRANTS,

SUBGRANTS, COOPERATIVE MASTER AGREEMENTS, AND CONTRACTS Contractor certifies compliance with all applicable standards, orders, regulations, and/or requirements issued pursuant to the Clean Air Act of 1970, as amended (42 U.S.C. 1857(h)), Section 508 of the Clean Water Act, as amended (13 U.S.C. 1368), Executive Order 117389 and Environmental Protection Agency Regulation, 40 CFR Part 15.

ARTICLE 31: COMPLIANCE WITH ENERGY POLICY AND CONSERVATION ACT Contractor certifies that Contractor will be in compliance with mandatory standards and policies relating to energy efficiency which are contained in the state energy conservation plan issued in compliance with the Energy Policy and Conservation Act (Pub. L. 94-163, 89 Stat. 871).

DocuSign Envelope ID: E4D77477-E07A-45AE-A42F-916BF5C46EDC Ambulances, EMS & Special Service Vehicles
Request For Proposal
HGACBuy/Cooperative Purchasing Program
Project ID: AM10-23
Release Date: Friday, June 9, 2023
Due Date: Thursday, August 10, 2023 12:00pm
Posted Friday, June 9, 2023 7:00am
Bid Unsealed Thursday, August 10, 2023 12:03pm
Pricing Unsealed Thursday, August 10, 2023 12:03pm
All dates & times in Central Time

3. Scope of Work / Specifications
This is an indefinite quantity/indefinite delivery offerings contract. The HGACBuy Customer is responsible to ensure adequate competition is performed between the various contractors or contractors outside of HGACBuy to determine price reasonableness that might be required per any funding agency. Customer will need to ensure compliance with any funding agency requirements before proceeding with a purchase order under this contract. Please consult legal counsel regarding questions concerning compliance as a contractor under this solicitation.

3.1. Overview
H-GAC is soliciting responses for selecting qualified manufacturers, dealers, distributors, and service providers of Ambulances, EMS and Other Specialty Vehicles and related services to make these types of products and services available to Customers of the HGACBuy Cooperative Purchasing Program under blanket type contracts. Customers (end users) may require selective acquisitions of equipment and/or services OR full turnkey projects necessitating additional services, training, and maintenance agreements. H-GAC is seeking the broadest possible selection of available ambulances, emergency medical response and specialty vehicles to best serve our customers by providing the largest selection of products/services available to meet their needs. This solicitation may include a request for a discount percent off price catalog, category, or manufacturer, or price list for supplies, materials, or not to exceed hourly rates for installation or repair. Respondents are not required to provide offerings on all categories.

3.2. Categories
This Solicitation is divided into ten (10) separate but related product categories (A-J). When submitting a response, Respondent may choose to submit a response to any of the categories or all of them. No additional weighted value will be assigned to a response that addresses more than one or all categories listed. All equipment must be the manufacturer’s new and current model and must be fully operational upon delivery to the Customer.

Alternative Fuel Vehicles: All responses that include electric, hybrid, or other alternative fuel vehicles must include these vehicles in Category G. If that specific vehicle is also available with an internal combustion engine (ICE), please list the ICE vehicle separately in the appropriate vehicle category. Category G will only include the alternative fuel vehicles, regardless of vehicle function or type.

Product categories are as follows:

DocuSign Envelope ID: E4D77477-E07A-45AE-A42F-916BF5C46EDC

1. Ambulance
Response listings/descriptions must be organized by major sub-categories, which include Manufacturer, Type (I, II, or III), module configurations/dimensions, chassis (make and model), 2WD/4WD, and fuel type.

2. Light/Medium Duty EMS Rescue Vehicle
Response listings/descriptions must be organized by major sub-categories, which include manufacturer, model, type/function, chassis (make and model), dimensions, 2WD/4WD, and fuel type.

3. Other Specialty Vehicle or Equipment
Category includes vehicles or trailers for command, communication, tactical response, or other related emergency response functions. Response listings/descriptions must be organized by major sub-categories, which shall include manufacturer, model, type/function, chassis (make and model), axle configuration, dimensions, 2WD/4WD, and fuel type.

4. EMS Vehicle Conversions
Response listings/descriptions must be organized by major sub-categories, which include manufacturer, model, type/function, chassis, 2WD/4WD, and fuel type.

5. Remount Services Only
Pricing for this service must include the cost of removing an existing body and reinstalling it on a different chassis, only. This service would apply where the chassis was supplied by the end user.

Note: Remounting Services are to be performed by an authorized dealer/remounter. Any specific certifications or warranties that may be requested by an end user regarding remounts is the end user’s responsibility and will be negotiated between the end user and the supplier/contractor when services are quoted.

6. Remount on Contractor Supplied Chassis
Pricing for these items must include the cost of the chassis plus the removal and reinstallation of the body.

7. Electric/Alternative Fuel Ambulance/EMS/Rescue Vehicles Response listings must be organized by manufacturer, model, vehicle type/function, and primary fuel/propulsion type.

8. Ambulance/EMS/Rescue Vehicle Service/Maintenance Plans Response listings must include specific details about which fees are included in costs, including current labor rates, and fee structures.

9. Ambulance/EMS/Rescue Vehicle Parts and Supplies
Response listing must include percentage discount.

10. Ambulance/EMS/Rescue Vehicle Options
Response listing must include percentage discount.

DocuSign Envelope ID: E4D77477-E07A-45AE-A42F-916BF5C46EDC

3.3. General Requirements
All products priced and sold pursuant to this Solicitation must, as applicable:

1. Meet all applicable requirements of federal, state and local laws and regulations.

2. Be manufacturer's normal offering with all standard features and functions and performance levels.

3. Be ready for turn-key operation upon delivery.

4. Respondent must include specifications, brochures, warranty information, and any other relevant product information with solicitation Response.

Note: “Unpriced/unpublished” options cannot be quoted on the Base Pricing List and may not be sold through this contract.

3.4. Additional Requirements
Licenses

1. Contractor must have and maintain the appropriate license(s) as required by the State of Texas, Department of Transportation, Division of Motor Vehicles, Motor Vehicle Commission Code [latest edition], or any other local, state and federal licenses required and which are applicable to the respondent’s operations.

2. The prescribed licenses must include the manufacturer/respondent, and any and all dealers and their representatives as may be required by the Motor Vehicle Division. Contractor must ensure all emergency and specialty vehicles sold are in accordance with the laws of the state where the sale and acquisition are made.

3. Contractor must maintain all licensing required by the State of Texas as applicable to their business operations during the entire contract term. If during the contract period such licensing lapses, Contractor will be in default and become subject to contract termination unless issued a stay or waiver.

Manuals

1. Contractor must supply at the time of delivery, at least two (2) sets of complete operations and service documentation covering the completed emergency vehicles as delivered and accepted (as per latest edition of KKK-A-1822F).

2. Respondent must supply the following information with their response: Technical Specifications, Product Brochures, Tear Sheets, Cut Sheets, Strippers, etc. which clearly show all the standard features and capabilities of each listing being bid.

DocuSign Envelope ID: E4D77477-E07A-45AE-A42F-916BF5C46EDC Warranty
Contractors must comply with the minimum warranty and maintenance requirements described below for any products or services provided under this Solicitation.

1. Contractor must furnish with response, and for all equipment sold through this H-GAC contract, the manufacturer's general warranty, which must be honored by all the manufacturer's authorized service locations.

2. All service/maintenance plan listings must clearly indicate the cost structure for such plans, clearly indicating which costs and fees are included (such as: hourly labor rates, shop fees, supply fees, environmental fees).

3. The Contractor will handle all warranty claims and all work must be completed within ten (10) calendar days after receipt of equipment/vehicle by the Contractor without cost to H-GAC or the Customer. Delayed warranties must be available for all vehicles and equipment. Warranty start date will be effective the date that the completed unit is placed into service by the Customer. The Contractor must furnish a delayed warranty card/document for each unit delivered and/or advise the Customer of the procedures to be followed for obtaining the delayed start of warranty coverage. Requests for delayed warranties will not exceed six months after delivery.

4. Any and all documents necessary to effect manufacturer’s warranty must be properly applied for and submitted by the Contractor. The Contractor will provide to H-GAC and the Customer a manufacturer’s warranty which will be honored by any of the manufacturer’s authorized dealers and a complete copy must be provided at the time of delivery. When additional warranties are available as standard, they must be included as a part of the response for the benefit of H-GAC and Customer.

5. The patient compartment, all modifications to the OEM chassis by Contractor on the accepted unit, equipment and parts will be guaranteed for a minimum period of one (1) year against defects in design, materials, and workmanship. The warranty period will begin upon final acceptance of the equipment. This warranty will cover parts and labor expenses.

6. On Type I & III emergency medical service MODULE the warranty period will be fifteen (15) years.

7. This warranty will be upgraded to its original status each time the module is remounted by Contractor, or a Contractor authorized remount facility, not to exceed five (5) years above the original warranty.

8. In the event any component part of equipment or materials furnished under these specifications, or its subsequent contract(s), becomes defective by reason of material or workmanship during said period, and the end user agency immediately notifies Contractor of such defect, Contractor will, at no expense to the End User agency or H-GAC, repair or replace equipment or component with new equipment or component.

9. Warranty of all system equipment is the sole responsibility of the Contractor under contract, but may be performed by their certified, designated agent.

DocuSign Envelope ID: E4D77477-E07A-45AE-A42F-916BF5C46EDC

3.5. Vehicle Requirements
All equipment and vehicles must be new and be the manufacturer’s latest and current model. Each vehicle must be fully assembled, adjusted, serviced and ready for immediate and continuous operation upon delivery. If the equipment or vehicle does not meet the specification requirements upon delivery, Contractor will be responsible for correcting all deficiencies and making any corrections or adjustments needed to attain specification requirements.

All equipment and vehicles must conform to applicable local, state, federal requirements and must comply to all applicable industry standards (examples: National Fire Protection Association (NFPA), Commission on Accreditation of Ambulance Services (CAAS), Federal Specification for the Star-of-Life Ambulance (KKK-A-1822F), Occupational Safety and Health Administration (OSHA)).

3.6. Service / Maintenance Plans and Parts
All service/maintenance plan listings must clearly indicate the cost structure for such plans, clearly indicating which costs and fees are included (ex: hourly labor rates, shop fees, supply fees, environmental fees).

3.7. Labor Hours Definitions
If the awarded contract contains hours for labor related services, the following definitions will apply:

1. “Business Day” Monday through Friday

2. “Business Hours” Standard Business Hours 8 a.m. to 5 p.m.

3. “Regular Time” Work that occurs during standard business hours

4. “Emergency Time” Work that occurs outside standard business hours

3.8. Administrative Fee
For each purchase order processed under an awarded contract, H-GAC will directly invoice the contractor an administrative fee (Order Processing Charge) applicable to the sale of all equipment and services submitted in contractor’s response. It is the contractor’s responsibility to remit the administrative fee within thirty (30) days of processing any customer’s purchase order, even if an invoice is not received from H-GAC. Contractor agrees that H-GAC will have the right, with reasonable notice, to inspect its records pertaining to purchase orders processed and the accuracy of the fees payable to H-GAC. For this solicitation the administrative fee is as follows:

Administrative Fee (per Purchase Order)
Category A – Ambulance: $1,000 per purchase order Category B – Light/Medium Rescue Vehicle: $1,000 per purchase order Category C – Specialty Vehicle/Equipment:

DocuSign Envelope ID: E4D77477-E07A-45AE-A42F-916BF5C46EDC Light Rescue/Special Service $1,000 per purchase order Heavy Rescue/Special Service $2,000 per purchase order All Trailers 2% per purchase order Category D – EMS Vehicle Conversions: $1,000 per purchase order Category E – Remount Services Only: $600 per purchase order Category F – Remount on Contractor Supplied Chassis: $600 per purchase order Category G –Electric/Alternative Fuel Vehicles Determined by category of vehicle Category H –Service/Maintenance Plans: 2% per purchase order Category I - Ambulance/Vehicle Parts and Supplies 2% per purchase order Category J - Ambulance/EMS/Rescue Vehicle Options No separate fee - part of vehicle

3.9. Final Contract Deliverables
Contractor agrees to submit written quarterly reports to H-GAC detailing all transactions during the previous three (3) month period. Reports must include, but are not limited, to the following information:
• Customer Name and address
• HGACBuy confirmation number
• Product/Service purchased, including Product Code, if applicable • Customer Purchase Order Number
• Purchase Order Date
• Product/Service dollar amount
• HGACBuy Order Processing Charge amount
Reports must be provided to H-GAC in Excel or other acceptable electronic format by the 30th day of the month following the quarter being reported. If Contractor defaults in providing Products or Services reporting as required by the contract, recourse may be exercised through cancellation of the contract and other legal remedies as appropriate.

DocuSign Envelope ID: E4D77477-E07A-45AE-A42F-916BF5C46EDC Attachment A
Braun Northwest, Inc.

Ambulances, EMS & Special Service Vehicles
Contract No.: AM10-23
Manufacturer Product Item Description Offered List
Price
HGACBuy
Discount
Category A - Ambulance
Braun
Northwest, Inc. AM23CA01 North Star - Type 1 - Ford F-350 4x4 - Diesel Engine - 147"L x 94"W x 72" HR 212,653.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CA02 North Star - Type 1 - Ford F-350 4x4 - Diesel Engine - 155"L x 94"W x 72" HR 237,613.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CA03 North Star - Type 1 - Ram 3500 4x4 - Diesel Engine - 147"L x 94"W x 72" HR 221,543.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CA04 North Star - Type 1 - GMC K3500 4x4 - Diesel Engine - 147"L x 94"W x 72" HR 211,873.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CA05 North Star - Type 1 - Chevrolet 4500 4x4 - Diesel Engine - 167"L x 94"W x 72" HR 239,292.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CA06 North Star - Type 1 - Ford F-450 4x4 - Diesel Engine - 147"L x 94"W x 72" HR 231,346.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CA07 North Star - Type 1 - Ford F-450 4x4 - Diesel Engine - 167"L x 94"W x 72" HR 235,296.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CA08 North Star - Type 1 - Ram 4500 4x4 - Diesel Engine - 167"L x 94"W x 72" HR 244,557.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CA09 North Star - Type 1 - Medium Duty - Ford F-650 4x2 - Diesel Engine - 167''L x 96''W x 72'' HR 266,552.00$ -$ 1,500.00
Braun
Northwest, Inc. AM23CA10 North Star - Type 1 - Medium Duty - International - Diesel Engine - 167"L x 96''W x 72'' HR 269,771.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CA11 North Star - Type 1 - Medium Duty - Freightliner - Diesel Engine - 167"L x 96''W x 72'' HR 275,270.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CA12 North Star - Type 2 - MB Sprinter Van 156,817.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CA13 North Star - Type 2 - Promaster Van 159,701.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CA14 North Star - Type 2 - Ford Transit AWD Gas 164,638.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CA15 North Star - Type 3 - Ford E-350 - Gas Engine - 147"L x 94"W x 72" HR 192,750.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CA16 North Star - Type 3 - GMC G3500 - Gas Engine - 147"L x 94"W x 72" HR 199,296.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CA17 North Star - Type 3 - Ford E-450 - Gas Engine - 167"L x 94"W x 72" HR 199,690.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CA18 North Star - Type 3 - GMC 4500 - Gas Engine - 167"L x 94"W x 72" HR 204,991.00$ -$ 1,500.00 Category B - Light/Medium EMS Rescue Vehicle
Braun
Northwest, Inc. AM23CB01 North Star - Fire Rescue - Ford F-550 4x4 Crew Cab - Diesel Engine - 116"L x 94"W 199,255.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CB02 North Star - Fire Rescue - Ford F-550 4x4 Regular Cab - Diesel Engine - 116"L x 94"W 191,824.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CB03 North Star - Fire Rescue - Ram 5500 4x4 Crew Cab - Diesel Engine - 116"L x 94"W 207,228.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CB04 North Star - Fire Rescue - Ram 5500 4x4 Regular Cab - Diesel Engine - 116"L x 94"W 199,338.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CB05 North Star - Fire Rescue - Ford F-550 4x4 Crew Cab - Diesel Engine - 147"L x 94"W 200,248.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CB06 North Star - Fire Rescue - Ford F-550 4x4 Regular Cab - Diesel Engine - 147"L x 94"W 193,322.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CB07 North Star - Fire Rescue - Ram 5500 4x4 Crew Cab - Diesel Engine - 147"L x 94"W 208,726.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CB08 North Star - Fire Rescue - Ram 5500 4x4 Regular Cab - Diesel Engine - 147"L x 94"W 200,836.00$ -$ 1,500.00 1 DocuSign Envelope ID: E4D77477-E07A-45AE-A42F-916BF5C46EDC Braun
Northwest, Inc. AM23CB09 North Star - Fire Rescue - Ford F-550 4x4 Regular Cab - Diesel Engine - 167"L x 94"W 198,322.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CB10 North Star - Fire Rescue - Ram 5500 4x4 Regular Cab - Diesel Engine - 167"L x 94"W 205,836.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CB11 North Star - Fire Rescue - Ford F-550 4x4 Regular Cab - Diesel Engine - 192"L x 94"W 220,140.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CB12 North Star - Fire Rescue - Ram 5500 4x4 Regular Cab - Diesel Engine - 192"L x 94"W 226,270.00$ -$ 1,500.00 Category C - Other Specialty Vehicle or Equipment
Braun
Northwest, Inc. AM23CC01 North Star - Prisoner Transport - Ford E-350 - Gas Engine - 138"L x 94"W x 57.875''HR 140,354.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CC02 North Star - Prisoner Transport - Ford F-350 4x4 - Diesel Engine - 143"L x 94"W x

57.75"HR 155,542.00$ -$ 1,500.00
Braun
Northwest, Inc. AM23CC03 North Star - Prisoner Transport - Ford F-450 4x2 Regular Cab - Diesel Engine - 191"L x 94"W x 72.875"HR 196,087.00$ -$ 1,500.00
Braun
Northwest, Inc. AM23CC04 North Star - Prisoner Transport - Ford F-550 4x2 - Regular Cab - Diesel Engine - 197''L x 94''W x 73'' HR 213,909.00$ -$ 1,500.00
Braun
Northwest, Inc. AM23CC05 North Star - Prisoner Transport - Freightliner M2 4x2 - Regular Cab - Diesel Engine - 197''L x 94'' W x 73''HR 245,915.00$ -$ 1,500.00
Braun
Northwest, Inc. AM23CC06 North Star - Prisoner Transport - Ford F-650 4x2 - Super Cab - Diesel Engine - 197''L x 94'' W x 73''HR 246,335.00$ -$ 1,500.00
Braun
Northwest, Inc. AM23CC07 North Star - Prisoner Transport - Ram 4500 4x2 - Regular Cab - Gas Engine - 197"L x 94"W x 72 "HR 217,020.00$ -$ 1,500.00
Braun
Northwest, Inc. AM23CC08 North Star - EOD Command - Ford F-550 4x4 - Regular Cab - Diesel Engine - 191''L x 94'' W x 80'' HR 274,359.00$ -$ 1,500.00
Braun
Northwest, Inc. AM23CC09 North Star - EOD Command - International MV607 4x2 - Crew Cab - Diesel Engine - 222''L x 100''W x 84''HR 364,112.00$ -$ 1,500.00
Braun
Northwest, Inc. AM23CC10 North Star - SWAT Command - Ford F-550 4x4 - Regular Cab - Diesel Engine - 192''L x 94'' W x 78'' HR 234,524.00$ -$ 1,500.00
Braun
Northwest, Inc. AM23CC11 North Star - Hazardous Materials Command - Ford F-550 4x4 - Regular Cab - Diesel Engine - 189''L x 96'' W x 72'' HR 273,464.00$ -$ 1,500.00
Braun
Northwest, Inc. AM23CC12 North Star - Crime Scene Command - Ford F-350 4x4 - Diesel Engine - 147''L x 94''W x 72''HR 228,796.00$ -$ 1,500.00
Braun
Northwest, Inc. AM23CC13 North Star - Mobile Command - Ford F-650 4x2 - Diesel Engine - 196''L x 94''W x 76''HR 290,290.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CC14 North Star - Wildland Crew Body - 198''L x 98''W x 78'' HR 215,849.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CC15 North Star - Command Van - Transit AWD - Gas 152,873.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CC16 North Star - Prisoner Transport - Freightliner M2 106 Plus 4x2 - Diesel Engine - 351"L x 102"W x 117" HR 494,629.00$ -$ 1,500.00
Category E - Remount Services Only
Braun
Northwest, Inc. AM23CE01 North Star - Remount of Northstar Module 56,159.00$ -$ 1,500.00 Category F - Remount on Contractor Supplied Chassis
Braun
Northwest, Inc. AM23CE02 North Star - Remount of Northstar Module - Ford F-350 4x4 - Regular Cab - Diesel Engine 129,926.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CE03 North Star - Remount of Northstar Module - Ford F-450 4x4 - Regular Cab - Diesel Engine 138,950.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CE04 North Star - Remount of Northstar Module - Ford E-350 4x2 - Regular Cab - Gas Engine 102,267.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CE05 North Star - Remount of Northstar Module - Ford E-450 4x2 - Regular Cab - Gas Engine 104,412.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CE06 North Star - Remount of Northstar Module - GMC G3500 4x2 - Regular Cab - Gas Engine 93,569.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CE07 North Star - Remount of Northstar Module - GMC G4500 4x2 - Regular Cab - Gas Engine 94,973.00$ -$ 1,500.00 2 DocuSign Envelope ID: E4D77477-E07A-45AE-A42F-916BF5C46EDC Braun
Northwest, Inc. AM23CE08 North Star - Remount of Northstar Module - Chevrolet 4500 4x4 - Regular Cab - Diesel Engine 139,889.00$ -$ 1,500.00
Braun
Northwest, Inc. AM23CE09 North Star - Remount of Northstar Module - Ram 3500 4x4 - Regular Cab - Diesel Engine 131,139.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CE10 North Star - Remount of Northstar Module - Ram 4500 4x4 - Regular Cab - Diesel Engine 150,204.00$ -$ 1,500.00 Braun
Northwest, Inc. AM23CE11 North Star - Remount of Northstar Module - International MV607 4x2 - Regular Cab - Diesel Engine 175,328.00$ -$ 1,500.00
Braun
Northwest, Inc. AM23CE12 North Star - Remount of Northstar Module - Freightliner M2 4x2 - Regular Cab - Diesel Engine 168,352.00$ -$ 1,500.00
Braun
Northwest, Inc. AM23CE13 North Star - Remount of Northstar Module - Ford F-650 4x2 - Regular Cab - Diesel Engine 168,509.00$ -$ 1,500.00 3 DocuSign Envelope ID: E4D77477-E07A-45AE-A42F-916BF5C46EDC

REQUEST FOR PROPOSAL
AM10-23

AMBULANCES, EMS & SPECIAL SERVICE VEHICLES

Houston-Galveston Area Council
3555 Timmons Ln
Houston, TX 77027

RELEASE DATE: June 9, 2023
DEADLINE FOR QUESTIONS: June 23, 2023
RESPONSE DEADLINE: August 10, 2023, 12:00 pm

RESPONSES MUST BE SUBMITTED ELECTRONICALLY TO:
https://procurement.opengov.com/portal/h-gac
Houston-Galveston Area Council

REQUEST FOR PROPOSAL
Ambulances, EMS & Special Service Vehicles
I. Summary and Timeline ................................ ................................ .........

II. Inquiries / Clarifications / Modifications / Submission ..........................

III. Scope of Work / Specifications ................................ .............................

IV. Additional Resources / Website Links ................................ ...................

V. Solicitation Requirements ................................ ................................ .....

VI. Contract Term / Multiple Awards / Usage................................ .............

VII. Goal for DBE Contracting ................................ ................................ ......

VIII. Submission Contents Details / Required Documents / Uploads ............

IX. Evaluation Criteria ................................ ................................ ................

X. Evaluation / Selection / Tie Bids ................................ ............................

XI. Presentation / Demo/ Interview and Best and Final .............................

XII. Approval / Final and Post Award ................................ ...........................

XIII. Debrief / Protest ................................ ................................ ...................

Attachments:

A - HGACBuy Solicitation T&Cs

Request For Proposal #AM10-23
Title: Ambulances, EMS & Special Service Vehicles
3 1. SUMMARY AND TIMELINE

1.1. Summary
The Cooperative Purchasing Program (HGACBuy) of the Houston-Galveston Area Council of Governments is soliciting offerings for the furnishing of products/services as described in this Solicitation. Texas Local Government Code (Title 7, Chapters 771 and 791) establishes the authority for H-GAC to provide cooperative contract products and services to Texas local governments and in other states if their statutes allow. With that authority, H-GAC makes varied categories of contracted products and services available.

1.2. Background
About the Cooperative
H-GAC is a government agency which provides a Cooperative Purchasing Program as part of its service to other government agencies. The Program currently makes blanket type contracts covering products and services for the use of its membership of more than 9000 local government participants in Texas and other States (Customers) which include cities, counties, emergency services districts, school districts, and non-profit organizations. Any local government or non-profit organization may participate in the Program if their state law allows. There is no cost to join and become a member of the H-GAC Cooperative Purchasing Program.

H-GAC's Cooperative Purchasing Program, known as HGACBuy, was established pursuant to Texas Interlocal Cooperation Act [Texas Local Government Code, Title 7, Chapter 791]. The Act allows local governments and certain non-profits to contract or agree under the terms of the Act to make purchases or provide purchasing services and other administrative functions appropriately established by another government entity. The Interlocal Contract (ILC) is the required legal document that establishes a link between the Customer (local governments and certain non-profits) and HGACBuy and gives the Customer access to HGACBuy contracts.

HGACBuy contracts are established based on the requirements of Texas Local Government Code, Chapter 252 and/or other applicable State of Texas or Federal procurement requirements. Products and services are contracted after having been subjected to either a competitive bid (ITB); competitive proposal (RFP); or Request for Qualification and Pre-Qualification (RFQ) depending on the category type.

Contracts are blanket type, usually for a term of two (2), three (3), or four (4) years. Use of HGACBuy for purchases by any Customer is strictly at the discretion of that entity. Customers issue purchase orders and pay the HGACBuy Contractor directly. The Customer also sends HGACBuy a copy of the purchase order and the Contractor is responsible for reporting the sale to HGACBuy as a contract requirement.

1.3. Timeline
Date Issued: June 9, 2023
Request For Proposal #AM10-23
Title: Ambulances, EMS & Special Service Vehicles
4 Pre-Proposal/Bid Conference Date: (Non-
Mandatory)
June 22, 2023, 2:00pm
The virtual meeting will be held using Zoom,
registration is required. Once registered, applicants
will receive notification and a direct link for
participation. Click on the following link to register:
https://us06web.zoom.us/meeting/register/tZcqcO
-vpjwoH92tAJ9fZvx3HUfEjaMZGZUn

It will be assumed that Respondents attending any
conference have reviewed the Solicitation in detail
and are prepared to raise any substantive
questions which have not already been addressed
by H-GAC in this Solicitation.

Questions Deadline: June 23, 2023, 12:00pm
Closing Date/Submission Deadline: August 10, 2023, 12:00pm Estimated Board Approval Date: September 19, 2023
Estimated Contract Start Date: October 1, 2023

Request For Proposal #AM10-23
Title: Ambulances, EMS & Special Service Vehicles
5 2. INQUIRIES / CLARIFICATIONS / MODIFICATIONS / SUBMISSION Inquiries: Respondents must submit questions by the Questions deadline. Telephone inquiries will not be accepted. H-GAC will respond as completely as possible to each question. Questions and answers will be posted as soon as available. The names of respondents who submit questions will not be disclosed.

Clarifications: All clarifications will be available in the Question and Answer and Addenda Sections in OpenGov, only the information in these sections should be used in preparing a response; verbal communications and other written documents intended to clarify and interpret will not legally bind H- GAC. H-GAC does not assume responsibility for the receipt of any clarifying information. Respondents must periodically check for updates.

Modifications: Each Respondent must carefully examine all Solicitation documents and become thoroughly familiar with all requirements prior to submission to ensure the response meets the intent of this Solicitation. Respondent is responsible for making all investigations and examinations that are necessary to ascertain conditions affecting the requirements of this Solicitation. Failure to make such investigations and examinations will not relieve the Respondent from obligation to comply, in every detail, with all provisions and requirements of the Solicitation.

Submission: Responses may be submitted any time prior to the submission deadline. Respondents may modify submissions that have already been submitted, before the deadline. Recording of proposal submission time and date will occur via OpenGov. To satisfy any required public opening, the respondent list is made available in the OpenGov Public Portal after the deadline.

Request For Proposal #AM10-23
Title: Ambulances, EMS & Special Service Vehicles
6 3. SCOPE OF WORK / SPECIFICATIONS
This is an indefinite quantity/indefinite delivery offerings contract. The HGACBuy Customer is responsible to ensure adequate competition is performed between the various contractors or contractors outside of HGACBuy to determine price reasonableness that might be required per any funding agency. Customer will need to ensure compliance with any funding agency requirements before proceeding with a purchase order under this contract. Please consult legal counsel regarding questions concerning compliance as a contractor under this solicitation.

Category G will only include the alternative fuel vehicles, regardless of vehicle function or type.

Product categories are as follows:

A. Ambulance
Response listings/descriptions must be organized by major sub-categories, which include Manufacturer, Type (I, II, or III), module configurations/dimensions, chassis (make and model), 2WD/4WD, and fuel type.

B. Light/Medium Duty EMS Rescue Vehicle
Response listings/descriptions must be organized by major sub-categories, which include manufacturer, model, type/function, chassis (make and model), dimensions, 2WD/4WD, and fuel type.

Request For Proposal #AM10-23
Title: Ambulances, EMS & Special Service Vehicles
7 C. Other Specialty Vehicle or Equipment
Category includes vehicles or trailers for command, communication, tactical response, or other related emergency response functions. Response listings/descriptions must be organized by major sub-categories, which shall include manufacturer, model, type/function, chassis (make and model), axle configuration, dimensions, 2WD/4WD, and fuel type.

D. EMS Vehicle Conversions
Response listings/descriptions must be organized by major sub-categories, which include manufacturer, model, type/function, chassis, 2WD/4WD, and fuel type.

E. Remount Services Only
Pricing for this service must include the cost of removing an existing body and reinstalling it on a different chassis, only. This service would apply where the chassis was supplied by the end user.

F. Remount on Contractor Supplied Chassis
Pricing for these items must include the cost of the chassis plus the removal and reinstallation of the body.

G. Electric/Alternative Fuel Ambulance/EMS/Rescue Vehicles Response listings must be organized by manufacturer, model, vehicle type/function, and primary fuel/propulsion type.

H. Ambulance/EMS/Rescue Vehicle Service/Maintenance Plans Response listings must include specific details about which fees are included in costs, including current labor rates, and fee structures.

I. Ambulance/EMS/Rescue Vehicle Parts and Supplies
Response listing must include percentage discount.

J. Ambulance/EMS/Rescue Vehicle Options
Response listing must include percentage discount.

3.3. General Requirements
All products priced and sold pursuant to this Solicitation must, as applicable:

A. Meet all applicable requirements of federal, state and local laws and regulations.

B. Be manufacturer's normal offering with all standard features and functions and performance levels.

C. Be ready for turn-key operation upon delivery.

Request For Proposal #AM10-23
Title: Ambulances, EMS & Special Service Vehicles
8 D. Respondent must include specifications, brochures, warranty information, and any other relevant product information with solicitation Response.

Note: “Unpriced/unpublished” options cannot be quoted on the Base Pricing List and may not be sold through this contract.

3.4. Additional Requirements
Licenses
A. Contractor must have and maintain the appropriate license(s) as required by the State of Texas, Department of Transportation, Division of Motor Vehicles, Motor Vehicle Commission Code [latest edition], or any other local, state and federal licenses required and which are applicable to the respondent’s operations.

B. The prescribed licenses must include the manufacturer/respondent, and any and all dealers and their representatives as may be required by the Motor Vehicle Division. Contractor must ensure all emergency and specialty vehicles sold are in accordance with the laws of the state where the sale and acquisition are made.

C. Contractor must maintain all licensing required by the State of Texas as applicable to their business operations during the entire contract term. If during the contract period such licensing lapses, Contractor will be in default and become subject to contract termination unless issued a stay or waiver.

Manuals
A. Contractor must supply at the time of delivery, at least two (2) sets of complete operations and service documentation covering the completed emergency vehicles as delivered and accepted (as per latest edition of KKK-A-1822F).

B. Respondent must supply the following information with their response: Technical Specifications, Product Brochures, Tear Sheets, Cut Sheets, Strippers, etc. which clearly show all the standard features and capabilities of each listing being bid.

Warranty
Contractors must comply with the minimum warranty and maintenance requirements described below for any products or services provided under this Solicitation.

A. Contractor must furnish with response, and for all equipment sold through this H-GAC contract, the manufacturer's general warranty, which must be honored by all the manufacturer's authorized service locations.

B. All service/maintenance plan listings must clearly indicate the cost structure for such plans, clearly indicating which costs and fees are included (such as: hourly labor rates, shop fees, supply fees, environmental fees).

Request For Proposal #AM10-23
Title: Ambulances, EMS & Special Service Vehicles
9 C. The Contractor will handle all warranty claims and all work must be completed within ten (10) calendar days after receipt of equipment/vehicle by the Contractor without cost to H-GAC or the Customer. Delayed warranties must be available for all vehicles and equipment. Warranty start date will be effective the date that the completed unit is placed into service by the Customer.

The Contractor must furnish a delayed warranty card/document for each unit delivered and/or advise the Customer of the procedures to be followed for obtaining the delayed start of warranty coverage. Requests for delayed warranties will not exceed six months after delivery.

D. Any and all documents necessary to effect manufacturer’s warranty must be properly applied for and submitted by the Contractor. The Contractor will provide to H-GAC and the Customer a manufacturer’s warranty which will be honored by any of the manufacturer’s authorized dealers and a complete copy must be provided at the time of delivery. When additional warranties are available as standard, they must be included as a part of the response for the benefit of H-GAC and Customer.

E. The patient compartment, all modifications to the OEM chassis by Contractor on the accepted unit, equipment and parts will be guaranteed for a minimum period of one (1) year against defects in design, materials, and workmanship. The warranty period will begin upon final acceptance of the equipment. This warranty will cover parts and labor expenses.

F. On Type I & III emergency medical service MODULE the warranty period will be fifteen (15) years.

G. This warranty will be upgraded to its original status each time the module is remounted by Contractor, or a Contractor authorized remount facility, not to exceed five (5) years above the original warranty.

H. In the event any component part of equipment or materials furnished under these specifications, or its subsequent contract(s), becomes defective by reason of material or workmanship during said period, and the end user agency immediately notifies Contractor of such defect, Contractor will, at no expense to the End User agency or H-GAC, repair or replace equipment or component with new equipment or component.

I. Warranty of all system equipment is the sole responsibility of the Contractor under contract, but may be performed by their certified, designated agent.

Request For Proposal #AM10-23
Title: Ambulances, EMS & Special Service Vehicles
10 All equipment and vehicles must conform to applicable local, state, federal requirements and must comply to all applicable industry standards (examples: National Fire Protection Association (NFPA), Commission on Accreditation of Ambulance Services (CAAS), Federal Specification for the Star-of-Life Ambulance (KKK-A-1822F), Occupational Safety and Health Administration (OSHA)).

3.7. Labor Hours Definitions
If the awarded contract contains hours for labor related services, the following definitions will apply:

A. “Business Day” Monday through Friday
B. “Business Hours” Standard Business Hours 8 a.m. to 5 p.m.

C. “Regular Time” Work that occurs during standard business hours D. “Emergency Time” Work that occurs outside standard business hours

3.8. Administrative Fee
For each purchase order processed under an awarded contract, H-GAC will directly invoice the contractor an administrative fee (Order Processing Charge) applicable to the sale of all equipment and services submitted in contractor’s response. It is the contractor’s responsibility to remit the administrative fee within thirty (30) days of processing any customer’s purchase order, even if an invoice is not received from H-GAC. Contractor agrees that H-GAC will have the right, with reasonable notice, to inspect its records pertaining to purchase orders processed and the accuracy of the fees payable to H- GAC. For this solicitation the administrative fee is as follows:

Light Rescue/Special Service $1,000 per purchase order Heavy Rescue/Special Service $2,000 per purchase order All Trailers 2% per purchase order Category D – EMS Vehicle Conversions: $1,000 per purchase order Category E – Remount Services Only: $600 per purchase order Category F – Remount on Contractor Supplied Chassis: $600 per purchase order Category G –Electric/Alternative Fuel Vehicles Determined by category of vehicle Request For Proposal #AM10-23
Title: Ambulances, EMS & Special Service Vehicles
11 Category H –Service/Maintenance Plans: 2% per purchase order Category I - Ambulance/Vehicle Parts and Supplies 2% per purchase order Category J - Ambulance/EMS/Rescue Vehicle Options No separate fee - part of vehicle

Request For Proposal #AM10-23
Title: Ambulances, EMS & Special Service Vehicles
12 4. ADDITIONAL RESOURCES / WEBSITE LINKS

4.1. Reference Websites
• HGACBuy Website – www.hgacbuy.org
• HGACBuy Open Solicitations – www.hgacbuy.org/bid-notices • HGACBuy Sample Contract – https://www.hgacbuy.org/bid-notices/solicitation-forms-resources • HGACBuy Customer and Contractor Handbook – https://www.hgacbuy.org/bid- notices/solicitation-forms-resources
• HGACBuy Events – https://www.hgacbuy.org/events
• HGACBuy Marketing – https://www.hgacbuy.org/marketing Note: Sample Contract and Handbook are reference material only, do not constitute a contract, or become incorporated as requirements of this Solicitation. Only information supplied in this Solicitation or by a Letter of Clarification posted to the HGACBuy website should be used in the preparation of a submission.

The actual final contract will be the same or nearly the same as the sample, however H-GAC reserves the right to update the actual contract as required for program or regulation requirements.

Note: Successful Respondents MAY NOT process any purchase orders for sales until all contract documents have been completely executed.

Request For Proposal #AM10-23
Title: Ambulances, EMS & Special Service Vehicles
13 5. SOLICITATION REQUIREMENTS
Respondent must be compliant with all licensing, permitting, registration or other applicable legal or regulatory requirements imposed by any governmental authority. It is Respondent’s responsibility to ensure that this requirement is met. H-GAC reserves the right to request copies of any license, permit, or other compliance related documentation at any time. Listed below are other requirements of responding to the Solicitation.

5.1. Contractor Orientation and Training
H-GAC believes that Contractor's familiarity with the operational policies and requirements of the Cooperative Purchasing Program is a key factor in achieving Customer satisfaction. The Contact Person listed on Contractor Status and Contact Form or an alternate, will be required to participate in an H-GAC vendor orientation and training as soon as possible after contract execution. In addition, other Contractor's staff who will be involved in any way with the HGACBuy Program should participate in orientation. The orientation may be presented as a teleconference or webinar or may be held in H-GAC's offices as determined by H-GAC and Contractor to be the most efficient and effective form of delivery.

Please visit https://www.hgacbuy.org/events for more information.

5.2. Nationwide Sales Opportunity
HGACBuy contracts provide various products and services to local governments and qualifying non- profits throughout the nation, and desires to make established contracts available to Customers wherever and whenever practicable. Once a contract is executed, Contractor is expected to expand the scope of its marketing effort to include sales to Customers in all areas of the United States. Please also view important guidelines and additional information regarding marketing the program at:
https://www.hgacbuy.org/marketing.

5.3. Corporate/Sales Commitment
Contractor is required to make some basic commitments to ensure the overall success of the HGACBuy program. By submission of a response, Respondent agrees that HGACBuy has the support of senior management and HGACBuy will be the primary government contracting vehicle when offering services/products awarded from this solicitation to eligible Customers nationwide. A further commitment to aggressively market the program, both independently as well in partnership with HGACBuy.

5.4. Manufacturer as Respondent
If Respondent is a manufacturer or wholesale distributor, the response received will be evaluated based on a response made in conjunction with that manufacturer’s authorized dealer/reseller network. Unless stated otherwise, a manufacturer or wholesale distributor Respondent is assumed to have a documented relationship with their dealer/reseller network where that network is informed of, and authorized to accept, purchase orders pursuant to any Contract resulting from this Solicitation on behalf of the manufacturer or wholesale distributor Respondent. Any listed dealer/reseller will be considered a sub-contractor of the Respondent. The relationship between the manufacturer and wholesale distributor Respondent and its dealer/reseller network must be indicated at the time of the submission.

Request For Proposal #AM10-23
Title: Ambulances, EMS & Special Service Vehicles
14 5.5. Dealer/Reseller as Respondent
If Respondent is a dealer/reseller of the products/services proposed, the response will be evaluated based on the Respondent’s authorization to provide those products and services from the manufacturer.

5.6. Approval by Manufacturer
Any awarded contractor must be approved by the manufacturer to sell, install, and service the brand of equipment submitted. Respondents to this solicitation must submit an approval letter from each manufacturer; authorization letters must include the regions in which equipment may be sold or serviced.

5.7. Structure of Response
Depending on the Product or Service, market structures and sales practices can differ substantially. For example, dealers may sell into any market or may be restricted to certain territories, manufacturers may sell direct or be limited by law to selling through independent dealerships, etc. H-GAC’s objective is to ensure that Customers, no matter where located, can buy contracted products/services and receive quality and timely service and support, while allowing for the most appropriate and effective response to this Solicitation. Responses to this Solicitation will only be accepted in conformance with the below scenarios and requirements. Note: Respondent can only be a party to one response structure.

A. Single Respondent Acting Alone Or As "Lead" For A Group: Respondent must complete and sign a Signature Page and all other required forms and, if contracted, will be solely responsible for all contractual requirements including administration, processing of purchase orders and handling of payments for transactions which may involve other dealers/distributors who deliver the products or services. Unless stated otherwise, a manufacturer or wholesale distributor Respondent is assumed to have a documented relationship with their dealer network where that dealer network is informed of, and authorized to accept, purchase orders pursuant to any Contract resulting from this Solicitation on behalf of the manufacturer or wholesale distributor Respondent. Any listed dealer will be considered a sub-contractor of the Respondent. The use of any dealer or reseller is not required if manufacturer or distributor does not employ such.

B. Multiple Respondents Acting Jointly: A single Response will be submitted, and each party to the Response must complete and sign a Signature Page and all other required forms must be included in the single Response. If the Response is successful, each party will sign a separate contract with H-GAC and will be individually responsible for compliance with all terms and conditions. Only those parties which have executed a contract with H-GAC are authorized to process purchase orders for sales and payments under the HGACBuy program.

Contractor may sell through HGACBuy anywhere subject to compliance with applicable laws and regulations. If the market structure in which Contractor operates requires a contract assignment for any sale, in certain limited circumstances, H-GAC may allow the contract to be assigned to a Manufacturer or another Dealer(s). Such assignment must be specific and detailed and must be approved by the Request For Proposal #AM10-23
Title: Ambulances, EMS & Special Service Vehicles
15 Contractor and H-GAC. Once assigned, the Contractor and assignee may NOT sell or service the same product line or category.

Depending on the structure of the network, H-GAC recognizes in some cases it may be necessary for the Purchase Order to be issued in the name of the reseller/dealer, etc., however the reseller, dealer, etc. is recognized only as a sub-contractor and will not receive a separate contract award or be assigned any portion of the contract. Any Lead Respondent utilizing a dealer/reseller network who is awarded a contract will be responsible for the processing of the Purchase Order through the network and the activities of the sale, reporting requirements, and remittance of applicable order processing fees

5.8. Contractor Status
Contractor is required to provide a status form, which is not part of any evaluation, but may be relevant to other state or local procurement requirements that apply to HGACBuy Customers. The following information will need to be captured:

A. Contractor’s status as a minority/woman-owned business enterprise, historically underutilized business, or service-disabled veteran; etc.

B. Whether Contractor or its ultimate parent or majority owner has its principal place of business in Texas or employs at least 500 persons in Texas; and
C. Whether Respondent is a Texas resident or a non-resident business.

5.9. HGACBuy Contractor / HGACBuy Member General Procedures A. Contracts are awarded through fair and open competition in compliance with applicable procurement rules and regulations.

B. The HGACBuy member sends a proposal request to an adequate number of Contractors in the desired Contract Category.

C. The Contractor prepares and sends a proposal/quote to the HGACBuy member. The HGACBuy member conducts an evaluation of cost or price reasonableness, if the HGACBuy member is using $250,000 (or current published Simplified Acquisition Threshold amount) or more of federal funds and an independent cost/price evaluation is necessary.

D. The Contractor and the HGACBuy member agree on a Purchase Order. Purchase Orders/Supplemental Contracts are reported and sent by individual HGACBuy members to the Contractor and to HGACBuy, where pricing is confirmed against the contract, an Order Confirmation is issued to the HGACBuy Member and copies of the Purchase Order/Supplemental Contract are logged and filed.

E. The Contractor delivers product(s)/service(s) directly to the HGACBuy member with a subsequent invoice the HGACBuy member upon completion of the work or delivery of the supplies.

F. The Contractor receives payment directly from HGACBuy member.

Request For Proposal #AM10-23
Title: Ambulances, EMS & Special Service Vehicles
16 G. The Contractor reports and remits the administrative fee to HGACBuy.

H. Reference also HGACBuy Customer and Contractor Handbook - https://www.hgacbuy.org/bid- notices/solicitation-forms-resources

5.10. Licensing and Permitting Requirements for Motor Vehicle Sales Respondent must be a properly franchised dealer authorized to sell and service, including warranty service, all products offered and sold in response to the Solicitation or under any H-GAC contract.

A. Contractor/Supplier will be responsible for securing any and all inspections required by law, including State Inspection stickers. Any fee charged for these inspections is the responsibility of the Contractor/Supplier.

B. At the time of delivery to the Customer, Contractors/Suppliers are required to provide temporary paper license tags/plates for motor vehicles or other equipment required by the State of Texas to be registered for operation on public highways.

C. TEXAS OCCUPATIONS CODE, TITLE 14, CHAPTER 2301 (Formerly known as “The Texas Motor Vehicle Commission Code”):

1. Section 2301.251: License Required: Generally (a) Unless a person holds a license issued under this chapter authorizing the activity, the person may not (1) engage in business as, serve in the capacity of, or act as a dealer, manufacturer, distributor, converter, representative, vehicle lessor, or vehicle lease facilitator in this state.

2. Sec. 2301.252: License required: Sale of New Motor Vehicles:(a) A person may not engage in the business of buying, selling, or exchanging new motor vehicles unless the person: (1) holds a franchised dealer's license issued under this chapter for the make of new motor vehicle being bought, sold, or exchanged; or (2) is a bona fide employee of the holder of a franchised dealer's license.

3. Respondents not submitting a response with a properly licensed Texas Motor Vehicle Dealer will only be eligible to sell motor vehicles on this contract outside of the State of Texas.

D. Licensed Franchised Dealers submitting a Response for new cabs & chassis with installed bodies and other equipment, by this Statute, are required to employ properly licensed converters for the conversions of the new motor vehicles.

E. The Act of Submitting a Response is regarded as doing business, as the entity is soliciting a sale.

Accordingly, each Respondent must be a licensed franchised dealer at the time the Response is submitted.

F. The units bid must be in full and complete compliance with all applicable safety and pollution requirements and regulations in effect at the time of submission. This includes but is not limited to standards established by the United States Department of Transportation, including the Federal Motor Vehicle Safety Standards (FMVSS), the Occupational Safety and Health Request For Proposal #AM10-23
Title: Ambulances, EMS & Special Service Vehicles
17 Administration (OSHA), the Environmental Protection Agency (EPA), the Texas Department of Transportation and the Texas Commission on Environmental Quality (TCEQ).

Request For Proposal #AM10-23
Title: Ambulances, EMS & Special Service Vehicles
18 6. CONTRACT TERM / MULTIPLE AWARDS / USAGE
Contract Term: H-GAC intends to award one or more contracts for the products/services requested under this Solicitation. The term of the resulting contract(s) will be for a period of four (4) years and until any outstanding orders against the contract have been fulfilled. H-GAC may, at its option, extend the contract for up to one (1) additional one-year term. H-GAC reserves the right to extend and/or expand the scope of the contract if deemed to be in the best interest of H-GAC and subject to H-GAC Board of Directors approval.

Multiple Awards: H-GAC reserves the right to award contract(s) for line items or groups of line items, at its sole discretion. H-GAC will not make separate awards for sales in Texas and for sales outside the state of Texas. In the case of acquisitions governed by the Motor Vehicle Division, the dealer is awarded the contract in Texas, and the Manufacturer is awarded the contract outside of Texas.

No Guarantee of Usage: H-GAC makes no guarantee of volume or usage under any contract resulting from this Solicitation. Services will be requested and contracted on an as needed basis and the type and value of each assignment will vary.

Request For Proposal #AM10-23
Title: Ambulances, EMS & Special Service Vehicles
19 7. GOAL FOR DBE CONTRACTING
H-GAC’s goal is to assure that small and minority businesses, women's business enterprises, and labor surplus area firms are used when possible in providing services under a contract. In accordance with federal procurement requirements of 2 CFR §200.321, if subcontracts are to be let, the prime contractor must take the affirmative steps listed below:

A. Placing qualified small and minority businesses and women’s business enterprises on solicitation lists.

B. Assuring that small and minority businesses and women’s business enterprises are solicited whenever they are potential sources.

C. Dividing total requirements, when economically feasible, into smaller task or quantities to permit maximum participation by small and minority businesses, and women’s business enterprises.

D. Establishing delivery schedules, where the requirement permits, which encourage participation by small and minority businesses, and women’s business enterprises.

E. Using the services and assistance as appropriate, of such organizations as the Small Business Administration and the Minority Business Development Agency of the Department of Commerce.

Nothing in this provision will be construed to require the utilization of any firm that is either unqualified or unavailable. The Small Business Administration (SBA) is the primary reference and database for information on requirements related to Federal Subcontracting https://www.sba.gov/federal- contracting/contracting-guide/prime-subcontracting
Contractor agrees to work with and assist HGACBuy customer in meeting any small and minority businesses, women's business enterprises, and labor surplus area firms targets and goals, as may be required by any rules, processes or programs they might have in place. Assistance may include compliance with reporting requirements, provision of documentation, consideration of Certified/Listed subcontractors, provision of documented evidence that an active participatory role for a small and minority businesses, women's business enterprises, and labor surplus area entity was considered in a procurement transaction, etc.

Request For Proposal #AM10-23
Title: Ambulances, EMS & Special Service Vehicles
20 8. SUBMISSION CONTENTS DETAILS / REQUIRED DOCUMENTS /

UPLOADS

8.1. Submission Upload Section

8.1.1. Executive Summary Response*
Provide a summary of key aspects of the contractor’s qualifications and indicate the Respondent’s commitment to provide the services proposed and certify that all statements and information prepared and submitted in the response to this Solicitation are current, complete, and accurate; and that the proposed solution for the project meets all the requirements of this Solicitation.

Maximum response length: 3000 characters
*Response required

8.1.2. Pricing*
Pricing must include Manufacturer’s Suggested Retail Price (MSRP) or List Price and provide a Percentage Discount from MSRP/List Price which clearly indicates the percentage off from MSRP or List price that HGACBuy members would pay if purchasing from this contract. Respondents who are awarded contracts for these products/services will be required to provide HGACBuy comprehensive price lists for all base models and options included in the contract and will be required to provide pricing/product updates to HGACBuy throughout the entire contract period to keep the price lists and product offerings current. All pricing must be clear and easily understandable, and clearly represent the total price to acquire the products/services covered in this contract.

Please download the below documents, complete, and upload. • AM10-23_Base_Response_Price...
*Response required

8.1.3. Customization Category Options*
Due to the highly specialized nature of these types of vehicles, all responses must include Customization Tables. These Customization Tables are meant to encompass those special/custom options that are not classified as the published “Manufacturer Standard Options”, and which may be required to address custom configurations of Ambulance, EMS and Other Specialty Vehicles. Respondent will group these options into broad categories and include specific options they would like to price within each of these customization categories. Respondent may quote as many categories as deemed necessary to cover any customization that may be required when building these custom emergency and specialty vehicles.

Please number and name each category accordingly. Below are some examples of customization categories and options that could be used when configuring these categories. The format shown below illustrates how these categories should be listed on your form. Respondent will provide a price range for each Category, and pricing should specify the low and high price range ($) for that specific category. This price range will apply to all options within the category (i.e. Category 1 – Chassis). Categories and pricing must be submitted on the Customization Category Options Pricing Sheet. Note: The sum of all Customization Category Options cannot exceed 25% of the total price (Base Model items + Published Options) on the HGAC Contractor Pricing Worksheet.

Request For Proposal #AM10-23
Title: Ambulances, EMS & Special Service Vehicles
21 Please download the below documents, complete, and upload. • AM10-23_Customization_Categ...
*Response required

8.1.4. Distinguishing Services*
Please download the below documents, complete, and upload. • Distinguishing_Services_v6....
*Response required

8.1.5. Business Practices and Operations
Please download the below documents, complete, and upload. • Business_Practices_and_Oper...

8.1.6. Licenses / Certifications*
Provide any and all licenses and certificates as required by the Solicitation. *Response required

8.1.7. Geographic Areas Served*
Please download the below documents, complete, and upload. • Geographic-Areas-Served.pdf
*Response required

8.1.8. Planned Authorized Retailers Distributors Dealers* Please download the below documents, complete, and upload. • Authorized-Dealer-Distribut...
*Response required

8.1.9. References*
Please download the below documents, complete, and upload.

Request For Proposal #AM10-23
Title: Ambulances, EMS & Special Service Vehicles
22 • References_v6.5.23.pdf
*Response required

8.1.10. Warranty, Service, and Technical Manuals*
Submit detailed Warranty, Service, Technical Manuals, or other relevant information or booklets with the Response. If Respondent submits a warranty which does not meet any minimum stated requirements in the Solicitation, Respondent agrees by submission of the Response that such warranty is automatically amended to meet the minimums.
*Response required

8.2. Required Documents/Certifications/Confirmations Section

8.2.1. Signature Page*
Please download the below documents, complete, and upload. This form must be returned signed with the response or the submission will be deemed non-responsive and will be rejected. *If submitting a joint response, each party must complete and sign a Signature Page and all other required forms must be included (reference section 6.7. Structure of Response). • Signature_Page_-_HGACBuy.pdf
*Response required

8.2.2. Small and Minority Business, Women's Business Enterprise, and Labor Surplus Affirmation*
• Small-and-Minority-Women-Su...
*Response required

8.2.3. Certification Regarding Debarment, Suspension, Ineligibility and Voluntary Exclusion for Covered Contracts*
Please download the below documents, complete, and upload. • Certification-Regarding-Deb...
*Response required

8.2.4. Certification Regarding Lobbying*
The undersigned certifies, to the best of his or her knowledge and belief, that:
(1) No Federal appropriated funds have been paid or will be paid, by or on behalf of the undersigned, to any person for influencing or attempting to influence an officer or employee of any agency, a Member of Congress, an officer or employee of Congress, or an employee of a Member of Congress in connection with the awarding of any Federal grant, the making of any Federal loan, the entering into of any cooperative agreement, and the extension, continuation, renewal, amendment or modification of any Federal contract, grant, loan, or cooperative agreement. (2) If any funds other than Federal appropriated funds have been paid or will be paid to any person for influencing or attempting to influence an officer or employee of any agency, a Member of Congress, an Request For Proposal #AM10-23
Title: Ambulances, EMS & Special Service Vehicles
23 officer or employee of Congress, or an employee of a Member of Congress in connection with this Federal contract, grant, loan, or cooperative agreement, the undersigned shall complete and submit Standard Form- LLL, "Disclosure of Lobbying Activities," in accordance with its instructions. (3) The undersigned shall require that the language of this certification be included in the award documents of all sub-awards at all tiers (including subcontracts, sub-grants, and contracts under grants, loans, and cooperative agreements) and that all sub- recipients shall certify and disclose accordingly.

This certification is a material representation of fact upon which reliance was placed when this transaction was made or entered into. Submission of this certification is a prerequisite for making or entering into this transaction imposed by section 1352, title 31, United States Code. Any person who fails to file the required certification shall be subject to a civil penalty of not less than $10,000 and not more than $100,000 for each such failure.
☐ Please confirm
*Response required

8.2.5. Certification Regarding Drug-Free Workplace Requirements* The grantee certifies that it will provide a drug-free workplace by: (a) Publishing a statement notifying employees that the unlawful manufacture, distribution, dispensing, possession or use of a controlled substance is prohibited in the grantee’s workplace and specifying the actions that will be taken against employees for violation of such prohibition; (b) Establishing a drug-free awareness program to inform employees about— (1) The dangers of drug abuse in the workplace; (2) The grantee’s policy of maintaining a drug-free workplace; (3) Any available drug counseling, rehabilitation and employee assistance programs, and (4) The penalties that may be imposed upon employees for drug abuse violations occurring in the workplace. (c) Making it a requirement that each employee to be engaged in the performance of the grant be given a copy of the statement required by paragraph (a); (d) Notifying the employee in the statement required by paragraph (a) that, as a condition of employment under the grant, the employee will— (1) Abide by the terms of the statement; and (2) Notify the employer of any criminal drug statute conviction for a violation occurring in the workplace no later than five days after each conviction; (e) Notifying the agency within ten days after receiving notice under subparagraph (d)(2) from an employee or otherwise receiving actual notice of such conviction; (f) Taking one of the following actions, within 30 days of receiving notice under subparagraph (d)(2), with respect to any employee who is so convicted— (1) Taking appropriate personnel action against such an employee, up to and including termination; or (2) Requiring such employee to participate satisfactorily in a drug abuse assistance or rehabilitation program approved for such purposes by a Federal, State, or local health, law enforcement, or other appropriate agency; (g) Making a good faith effort to continue to maintain a drug-free workplace through implementation of paragraphs (a), (b), (c), (d), (e) and (f). ☐ Please confirm
*Response required

8.2.6. Filing Reports Form 1295 Certificate of Interested Parties* Please download the below documents, complete, and upload. Download a blank Form here:
https://www.ethics.state.tx.us/filinginfo/1295/
Request For Proposal #AM10-23
Title: Ambulances, EMS & Special Service Vehicles
24 • 1295.pdf
*Response required

8.2.7. Conflict of Interest Questionnaire*
Chapter 176 of the Texas Local Government Code requires contractors contracting or seeking to contract with H-GAC to file a conflict-of-interest questionnaire (CIQ) if they have an employment or other business relationship with an H-GAC officer or an officer's close family member. H-GAC officers include its Board of Directors and Executive Director, who are listed on the H-GAC website. Respondent must complete and file a CIQ with the Texas Ethics Commission if an employment or business relationship with H-GAC office or an officer's close family member as defined in the law exists. The required questionnaire and instructions are located on the Conflict of Interest page on the Texas Ethics Commission website. https://www.ethics.state.tx.us/forms/conflict/ Please confirm to acknowledge that the form will be filed if applicable. ☐ Please confirm
*Response required

8.2.8. Contractor Status and Contact Form*
Please download the below documents, complete, and upload. • Contractor-Status-and-Conta...
*Response required

8.2.9. No Excluded Nation or Foreign Terrorist Organization Certification* Please download the below documents, complete, and upload. • No-Excluded-Nation-Foreign-...
*Response required

8.2.10. HB89 SB52 Prohibition on Contracts with Companies Boycotting Israel Verification Form*
Please download the below documents, complete, and upload. • HB89-SB52-Verification-Form...
*Response required

8.2.11. Solicitation Terms and Conditions Confirmation* By submitting a response to this Solicitation, respondent agrees that it has read and fully intends to comply with the terms and conditions of this solicitation as applicable to any subsequent contract or funding agency requirements or agreements. Exceptions to these Terms and Conditions are not permitted. Please view the full Terms and Conditions located in the attachments. ☐ Please confirm
*Response required
Request For Proposal #AM10-23
Title: Ambulances, EMS & Special Service Vehicles
25 8.2.12. Company W-9*
Please upload a current company W-9.
*Response required
Request For Proposal #AM10-23
Title: Ambulances, EMS & Special Service Vehicles
26 9. EVALUATION CRITERIA
Submission must be responsive to all material requirements that will enable the evaluation committee to evaluate submissions in accordance with the evaluation criteria to make a recommendation to H-GAC officials. This includes a signed signature page by a person authorized to bind the company to any contract/purchase order that may result from this Solicitation; if subcontracting, may include the completed Small and Minority Business Affirmation Form.

No. Evaluation Criteria Scoring Method Weight (Points)

1. Products and Pricing
Price is competitive and all information is
completed on the pricing sheets as set out in
the submittal section of this solicitation.

Demonstrated ability to deliver services at a
reasonable cost and all elements of cost detail
are provided. If offering services, reasonable
total fee schedule/not to exceed hourly rates.

Any travel associated expenses that may be
incurred for additional offered services are
priced separately and cannot exceed current
U.S. General Services Administration
established rates. For more information please
visit: https://www.gsa.gov/travel-resources
0-5 Points 45
(45% of Total)

2. Distinguishing Services
Completed Distinguishing Services form.

Details outline to what extent Respondent can
demonstrate and document services, and
foster an atmosphere of quality and high
performance in its organization. Practices that
elevate Respondent beyond the
average/minimum standards of other
Respondents.
0-5 Points 20
(20% of Total)
Request For Proposal #AM10-23
Title: Ambulances, EMS & Special Service Vehicles
27 3. Business Practices and Operations
Completed Business Practices and Operations
form. Detailed acceptable information is
provided on Respondent’s history, practices,
and philosophies, demonstrating the ability to
effectively support this contract and HGACBuy
members’ needs; information is provided
related to organizational structure, and
includes key staff responsibilities. All licenses
and certificates are satisfactory and are
provided as required by the Solicitation. Details
are provided on any bankruptcies, plus safety
and insurance claims with which Respondent
has been involved during the past five (5)
years.
0-5 Points 10
(10% of Total)

4. Geographic Areas Served / Authorized
Distributor
Detailed geographic coverage is provided and
demonstrates the ability to meet the needs of
Customers throughout the United States. If
applicable, dealer network (nationwide) is
provided and describes how it will be used to
promote this program and provide
products/services to H-GAC members
nationwide. Approval letter from each
manufacturer is submitted (when applicable);
authorization letters include the regions in
which equipment may be sold or serviced. A
listing of all planned retailers/distributors (if
applicable), etc. that may be used during the
term of this contract to deliver goods or
services is provided.
0-5 Points 10
(10% of Total)
Request For Proposal #AM10-23
Title: Ambulances, EMS & Special Service Vehicles
28 5. Past Performance
An evaluation will be conducted of the
Respondents previous contract performance as
an HGACBuy contractor based on the
performance measured listed below. Those
with no history will receive the maximum for
this criterion. NOTE: For joint responses, each
party will be scored as outlined and an overall
average will be taken of all companies
submitting a signed signature page to
determine the overall score for each joint
submission.

PERFORMANCE MEASURES (2% each)
• Timely and accurate response to
request for information and/or
request for quotes/pricing
• Timely delivery of product or services
(as quoted at time of order
placement)
• Quality of products/service
• Timely and accurate submission of
Contractor’s Activity Report
• Timely payment of order processing
charge
0-5 Points 10
(10% of Total)

6. References
Five (5) adequate references and examples of
previous, similar work for government
customers in comparable size and
requirements are provided.
0-5 Points 5
(5% of Total)

Request For Proposal #AM10-23
Title: Ambulances, EMS & Special Service Vehicles
29 10. EVALUATION / SELECTION / TIE BIDS
Evaluation: An evaluation committee may consist of representatives from H-GAC and other stakeholders. The committee members will individually evaluate and numerically score each submission in accordance with the evaluation criteria section of this Solicitation.

Selection: Submissions will be evaluated based on a total top score of 100. The committee members will individually evaluate and numerically score each submission in accordance with the evaluation criteria section of this Solicitation. Respondents with a score of at least 70 may be eligible for a contract award recommendation, at the sole discretion of H-GAC.

Tie Bids: H-GAC may award a contract for tie bids by drawing lots or by awarding to multiple contractors. If time permits, the bidders involved shall be given an opportunity to attend the drawing.

The drawing must be witnessed by at least three (3) persons and the contract file must contain the names and addresses of the witnesses and the person supervising the drawing. When an award is made by drawing by lot after receipt of equal low bids, the buyer must describe how the tie was broken by providing a written statement that the contract award was made in accordance with the circumstances justifying the priority used to break the tie or select bids for a drawing by lot. This does not prohibit H- GAC from rejecting all bids.

Request For Proposal #AM10-23
Title: Ambulances, EMS & Special Service Vehicles
30 11. PRESENTATION / DEMO/ INTERVIEW AND BEST AND FINAL Presentation / Demonstration / Interview: The evaluation committee reserves the right to request and require that each Respondent provide a final presentation/demonstration/interview regarding submission at a scheduled date and time. No Respondent is entitled to this opportunity, and no Respondent will be entitled to attend the presentation/demonstration/interview of any other Respondent. The purpose of the presentation/demonstration/interview is to inform the work of the evaluation committee. If necessary, Respondents may be required to make more than one presentation/demonstration/interview. Interviews can incorporate clarifying questions of the evaluation committee and H-GAC reserves the right to utilize the information to complete final scoring of proposals after the presentation/demonstration/interview. During this process, the proposer cannot incorporate, or present new information not contained in the original submitted proposal.

Best and Final Offer (BAFO): H-GAC reserves the right to request a Best and Final Offer from finalist Respondent(s), if it deems such an approach necessary. In general, BAFO would consist of updated costs and answers to specific questions that were identified during the evaluation. If H-GAC chooses to invoke this option, Submissions would be re-evaluated by incorporating the information requested in the BAFO document, including costs, and answers to specific questions presented in the document. The specific format for the BAFO would be determined during evaluation discussions. Turnaround time for responding to a BAFO is usually brief (i.e., five (5) business days).

Request For Proposal #AM10-23
Title: Ambulances, EMS & Special Service Vehicles
31 12. APPROVAL / FINAL AND POST AWARD
A recommendation will be presented to the H-GAC Board of Directors for approval to execute a contract. H-GAC reserves the right to award based on the best interests of H-GAC, whether that be single or multiple awards. However, the final approval and selection of award lies with the Board of Directors. H-GAC reserves the right to delay that date as needed and to reject any and all submissions as deemed in its interest.

H-GAC reserves the right to require the awarded Contractor attend a post award meeting with H-GAC staff and/or other designated persons at H-GAC offices in Houston, Texas within thirty (30) calendar days after the award. The purpose of the meeting will be to discuss the terms and conditions and to provide additional information regarding the work tasks and requirements.

Request For Proposal #AM10-23
Title: Ambulances, EMS & Special Service Vehicles
32 13. DEBRIEF / PROTEST
Requesting a Debrief: Requests for a debriefing must be made in writing to HGACBuySolicitations@h- gac.com within five (5) working days after notification of non-selection. H-GAC reserves the right to not conduct debriefings if requests are made after that time. This procedure is NOT available to Respondents who did not participate in the selected Solicitation, to non-responsive or non-timely Respondents, or when all submissions are rejected.

Resolution of Protested Solicitations: Any Respondent who is aggrieved in connection with a purchase transaction may file a grievance. The grievance may be filed at any phase of the procurement, and up to five (5) days after the H-GAC Board of Directors public agenda is posted for action regarding the questioned item. Grievances filed more than five (5) working days after action by the H-GAC Board of Directors will not be deemed timely and will not be considered. In order for a Respondent to enter the grievance process, a written complaint must be sent to the Deputy Assistant Director of H-GAC by certified mail and sent to 3555 Timmons Lane, Houston, Texas 77027, which includes the following:

A. Name, mailing address and business phone number of the complainant.

B. Appropriate identification of the procurement being questioned.

C. A precise statement of the reasons for the protest.

D. Supporting exhibits, evidence, or documents to substantiate any claims.

The grievance must be based on an alleged violation of H-GAC’s Procurement Procedures, a violation of State or Federal Law (if applicable), or a violation of applicable grant or contract agreements to which H- GAC is a party. Failure to receive a procurement award from H-GAC in and of itself does not constitute a valid grievance. Upon receipt of grievance, the Deputy Executive Director will initiate the informal resolution process.

The Procurement and Contracts Department will contact the complainant and all interested parties and attempt to resolve the allegations informally within ten (10) working days from the date of complaint. If the allegations are successfully resolved by mutual agreement, documentation will be forwarded to the Deputy Executive Director of the resolution with specifics on each point addressed in the original complaint.

If the Procurement and Contracts Department is not successful in resolving the allegations, the complaint, along with the comments, will be forwarded to the Deputy Executive Director immediately.

The Deputy Executive Director will review all documentation. All interested parties will be given written notice of the date, time, and place of hearing and an opportunity to present evidence. A written decision will be issued within five (5) working days after the hearing along with notice of appeal rights.

The complainant may appeal the Deputy Executive Director’s decision by submitting a written appeal, within five (5) working days, to the Executive Director of H-GAC. The Executive Director, upon receipt of a written notice of appeal, will contact the complainant and schedule a hearing within ten (10) working days. The Executive Director of H-GAC has the option of appointing a Hearing Officer to preside over the hearing. If appointed, the Hearing Officer will conduct a hearing and forward a summary and recommended resolution to the Executive Director.

Request For Proposal #AM10-23
Title: Ambulances, EMS & Special Service Vehicles
33 The decision reached by the Executive Director or his designee will be final and conclusive. This decision will be forwarded to the complainant in writing within thirty (30) working days.

The Respondent may, if it elects to do so, appeal the final and conclusive decision of the Executive Director to a court of competent jurisdiction.

Sacramento City CouncilOctober 22, 2024

Sacramento City Council
October 22, 2024