Item 06 Suspension of Competitive Bidding, Contract Supplements and Budgetary Adjustments for the Martin Luther King Jr. (MLK) Library Renovation Project: (C15000840) (Two-Thirds Vote Required) [Published for 10-Day Review 1/23/2025] PART 3 — Sacramento City Council, February 4, 2025 (part 9 of 9)

www.reliablesprinkler.com
Maintenance
Model G6-56 Concealed Sprinklers should be inspected and maintained in accordance with NFPA 25. Do not clean sprinklers with soap and water, ammonia or any other cleaning fluids.

Remove dust by using a soft brush or gentle vacuuming. Replace any sprinkler or cover plate assembly, which has been painted (other than factory applied) or damaged in any way. A stock of spare sprinklers should be maintained to allow quick replacement of damaged or operated sprinklers. Prior to installation, sprinklers should be maintained in their original cartons and packaging until used to minimize the potential for damage to sprinklers that would cause improper operation or non-operation.

Guarantee
For the Reliable Automatic Sprinkler Co., Inc. guarantee, terms, and conditions, visit www.reliablesprinkler.com.

Ordering Information
Specify:
• Model G6-56 Concealed Quick Response Sidewall Sprinkler • Cover Plate Finish (See Table B)
P/N 9999970467
Notes:

1. Paint or any other coating applied over the factory finish will void all approvals and warranties.

2. Custom color paint is semi-gloss unless specified otherwise.

Standard Finishes Special Application Finishes
White Paint
Chrome
Off-White Paint
Black Paint
Custom Color Paint – Specify(2)
Raw Brass (Lacquered)
Bright Brass
Finished Bronze
Satin Chrome
Custom Printed
Cover Plate Finishes(1) Table B Figure 2Model G6 Wrench Bulletin 050
April 2023

Page 3 of 3 ends

www.reliablesprinkler.com
Thermon • 100 Thermon Dr • PO Box 609 San Marcos, TX 78667-0609 • Phone: 512-396-5801 • 1-800-820-4328 For the Thermon office nearest you visit us at www.thermon.com © Ther mon, Inc. • Printed in U.S.A. • Information subject to change.

Form TEP0128-0621

CONSTRUCTION
1 Pipe-mount expediter 2, glass-reinforced polymer
2 Three-wire RTD sensor (order separately)
3 Junction box, glass-reinforced polymer
4 316 Stainless Steel mountin g bracket

PRODUCT FEATURES
• Encapsulated electronics and control
• One temperature control module for wide range of
temperature control and limiter applications
• Energy saving accurate electronic temperature
control action
• Data highwa y communication capability
• Selectable automatic or manual reset limiter action
• Control/limiter setting in degrees Centigrade or
degrees Fahrenheit
• Combines power junction box and control module
in one unit
• Also available as ambient thermostat (WP mount
only)
• Refer to Form TEP0010, System Accessories - Heat
Tracing Cables for additional accessories.

Notes

1. When located outdoors and subject to solar gain, some current de-rating will be required. Contact Thermon for additional information.

2. The pipe mount expediter has a maximum pipe exposure temperature of 482°F (250°C).

3. The terminal blocks consist of:
(6) 8 AWG line/load/PE terminals
(3) 12 AWG comm. port terminals
(3) 12 AWG alarm relay terminals
(2 x 3) 14 AWG sensor terminals
See installation instructions for maximum wire size.

APPLICATION
The TraceNet ECM is an electronic control module
specifically designed for controlling electric
heat trace circuits used in freeze protection and
temperature maintenance applications. The ECM
serves both the temperature control as well as the
sensor and power connection for a heat trace circuit.

The ECM is housed in a glass reinforced nonmetallic
enclosure with an environmental protection rating
of IP66. Depending on options selected, the ECM
may be used as a combination temperature control
and limiter, a temperature controller with either
low or high temperature alarm, or a temperature
limiter. Rotary switches are provided for adjusting
temperature control and limiter set points. The
standard version of the ECM communicates on a
physical network of RS485 by using a Modbus RTU
communication protocol.

The ECM is approved for use in both ordinary (non-
classified) and hazardous (classified) areas.

The ECM-OS is available in a stainless steel junction
box for use in offshore applications. (Refer to Form
TEP0138)

RATINGS
Operating/control voltage.................................120/208/240 Vac Operating ambient range .......-60°C to 55°C (-76°F to 131°F) Minimum ambient storage range ....................-74°C (-100°F) Control switch type options .............................. SPST and DPST Switching current ratings 1
SPST .....30/30/20 amps 25°C, 40°C, 55°C (77°F, 104°F, 131°F) DPST .....28/23/17 amps 25°C, 40°C, 55°C (77°F, 104°F, 131°F) Alarm output current rating ......................................................... 2 A Electrical connection ...........................................terminal blocks 3 Adjustable temp. control range .......................................................... 0°C to 500°C (32°F to 932°F)
Measurement range ...........-60°C to 500°C (-76°F to 932°F) Measurement accuracy (ambient)
± 1°C (0° C to +55°C) ± 1.8°F (32°F to +131°F)
± 2°C (0°C to -60°C) ± 3.6°F (32°F to +131°F)
Temperature sensor(s) .........100 Ohm three wire Platinum RTD
High temp. alarm/trip ............................................programmable (auto or manual reset)
RTD input circuitry .....................................intrinsically safe (Ex i) Life expectancy .............................................................250,000 cycles II 2 G Ex eb mb [ib] IIC T4 Gb SIRA 12ATEX5239X
II 2 D Ex tb IIIC T135°C IP66 Db
International Electrotechnical Commission
IEC Certification Scheme for Explosive Atmospheres
SIR 12.0103X

CERTIFICATIONS/APPROVALS
1 2
3 Class I Division 2, Groups A, B, C, D
Class II Division 2, Groups F, G; Class III; T4

14.2709489X Ex eb mb [ib] IIC T4
Ex tb IIIC T135°C
Class 1, Zone 1, AEx eb mb [ib] IIC T4
Zone 21, AEx tb IIIC T135°C
4 WP Wall Mount Kit
XP Pipe Mount Kit
TRACENET™ ECM™

PRODUCT DATASHEET

ELECTRONIC CONTROL MODULE

PRODUCT REFERENCE LEGEND
Control Type
C = Controller (with
low temp alarm)
CH = Controller (with
high temp alarm)
CL = Controller and
Limiter
Mounting Options
XP = Pipe-Mount Expediter
WP = Wall Mount Bracket with Expediter
Switch Configuration
SP = Single Pole (120 Vac)
DP = Double Pole (208 or 240 Vac)
Comm. Network
1 = RS485
Nominal Voltage
Range
1 = 120 Vac
2 = 240 Vac
3 = 208 Vac
Cable Profile
P = RSX, VSX-HT, BSX, KSX,

HTSX, FP, HPT, USX
ECM-CL-12-P-XP-SP

TYPICAL WIRING DIAGRAM
(for controller with limiter)
Single Pole
Double Pole

L LN N C
C L
NO NC
Comm. Port Alarm Relay
Main supply Heater output
B
B
A
A
B
BRTD
Limiter Sensor
RTD
Controller Sensor
C-NC = alarm condition
or power off
C 1 2

L LL L C
C L
NO NC
Comm. Port Alarm Relay
Main supply Heater output
B
B
A
A
B
BRTD
Limiter Sensor
RTD
Controller Sensor
C-NC = alarm condition
or power off
C 1 2
TRACENET™ ECM™

PRODUCT DATASHEET

ELECTRONIC CONTROL MODULE
© Ther mon, Inc. • Printed in U.S.A. • Information subject to change.

United States: 100 Thermon Dr • PO Box 609 San Marcos, TX 78667-0609 • Phone: 512-396-5801 • 1-800-820-4328 For the Thermon office nearest you visit us at www.thermon.com

RATINGS
Available Watt densities ..........10, 20 W
/m (3,6 W/ft) at
10°C (50°F)
Nominal supply voltage
1 ....... 100-120 or 208-277 Vac
Maximum maintenan
ce temperature ... 65°
C (149°F)
Maximum continuous exposure temperature
Po
wer-off ................................................................85° C (185°F)
Minimum installation temperature ....... -60
°C (-76°F)
Minimum bend radius
@ -15°
C (59°F) ....................................................10 mm (3/8”) @ -60°
C (-76°F) ..............................................32 mm (1- 1/4”)

BASIC ACCESSORIES
Thermon offers system accessories designed
specifically for rapid, trouble-free installation of
Thermon heat tracing.

All trace heaters require a connection kit to comply
with approval requirements. Information on
accessories to complete a heater circuit installation
can be found in the “Freeze Protection Systems
Accessories” product specification sheet (Form
CPD1017U).

Notes

1. Trace heater may be energised at other voltages; contact Thermon for design assistance.

2. Circuit breaker sizing and earth-fault protection should be based on applicable local codes. Earth-fault protection of equipment should be provided for each branch circuit supplying electric heating equipment.

Contact Thermon for assistance with circuit breaker sizing.

APPLICATION
DLX protects small and medium diameter pipes
from rupture and leakage caused by freezing
conditions in light industrial and commercial
applications.

EASY TO INSTALL
Parallel circuitry allows DLX to be cut to suit any
length required in the field. Flexible materials and
small cross-section provide an excellent bending
radius for wrapping around complex geometries.

ENERGY EFFICIENT
The heat output of DLX varies along the length of
the traced equipment or surface, providing the
optimal heating for colder or warmer spots. As
the temperature drops, heat output increases.

Conversely, when the temperature increases, heat
output decreases
SAFE
DLX self-regulates to prevent overheating, even
when overlapped. Trace heaters are certified for
ordinary (non-classified) areas.

RELIABLE
Built with proven and proprietary compounding,
extrusion, and cross-linking technology, DLX
allows for continuous operation and extended life
expectancy.

Form TEP0250-1123
DLX™

PRODUCT DATASHEET

SELF-REGULATING HEAT TRACING

CONSTRUCTION

1. Nickel-plat
ed copper bus wires 0.6 mm2
(20 AW
G)

2. E-Beam cr
oss-linked semiconductive heating
matrix

3. E-Beam cr
oss-linked dielectric insulation

4. Tinned c
opper braid

5. Polyolefin o
verjacket provides additional
protection to core, insulation, and braid where
exposure to aqueous inorganic chemicals is
expected.

Options

6. Foil and Dr
ain wire configuration available with
standard OJ as an economical alternative to
braid.

CERTIFICATIONS/APPROVALS
1 6
234
5 Metallic Covering
B = Braid
F = Foil
Power Output
3 = 10 W/m (3 W/ft) @ 120/240 Vac
6 = 20 W/m (6 W/ft) @ 120/240 Vac
Outerjacket
OJ =
Polyolefin
Voltage Rating
1 = 100-120 Vac
2 = 208-277 V
ac
DLX–B–3–2–OJ

HOW TO SPECIFY
DLX™

PRODUCT DATASHEET

SELF-REGULATING HEAT TRACING

POWER OUTPUT CURVES
The power outputs shown apply to trace heater
installed on insulated metallic pipe (using the
procedures outlined in IEEE 515.1) at the service
voltages stated below. For use on other service
voltages, contact Thermon.

CIRCUIT BREAKER SIZING AND TYPE
Maximum circuit lengths for various circuit breaker
amperages are shown below. Circuit breaker sizing
and ground-fault protection should be based on
applicable local codes. For information on design
and performance on other voltages, contact
Thermon. Ground-fault protection of equipment
should be provided for each branch circuit
supplying electric heating equipment.
(m) (ft) (m) (ft) (m) (ft)
10 148 486 148 486 148 486
0 135 444 135 444 135 444
-20 135 444 135 444 135 444
-40 133 435 135 444 135 444
10 115 378 115 378 115 378
0 108 355 108 355 108 355
-20 104 342 108 355 108 355
-40 91 298 108 355 108 355
20 A 30 A 40 A
DLX 3-2
DLX 6-2
Type QOB/QO Circuit Breakers
240 Vac Service
Voltage
Max. Circuit Length 3 vs . Breaker Size
meters (feet)
Catalog
Number
Start-Up
Temperature
°C
Notes:

1. For more precise power output values as a function of pipe temperature, refer to CompuTrace®.

2. Based on the trip current characteristic of Type QOB or Type QO equipment protection devices. For devices with other trip current characteristics, contact Thermon.

3. The maximum circuit length is for one continuous length of trace heater, not the sum of segments of cable. Refer to CompuTrace® design software or contact Thermon for current loading of segments.

Product Type
120 Vac Nominal
Product Type
240 Vac Nominal
Power Output at
10°C (50°F) W/m
DLX 3-1 DLX 3-2 10
DLX 6-1 DLX 6-2 20
40 500 30 652010 60
Pipe Temperature °C
W / m
25 0
20 15
10 5
DLX 3
DLX 6
(m) (ft)
10 88 288
0 78 255
-20 77 253
-40 66 216
10 62 204
0 58 190
-20 52 170
-40 46 150
DLX 3-1
DLX 6-1
Type QOB/QO Circuit Breakers
Max. Circuit
Length vs.

Breaker Size
meters (feet)
120 Vac Service
Voltage
Product
Type
Start-Up
Temperature
°C
20 A
Group 4 Architecture Research + Planning CITY OF SACRAMENTO - Martin Luther King, Jr. Library Remodel
PART 1 - Group4 Project No. 23604-01 Back Check Submission November 01, 2024 APENDIX D-1
APPENDIX D:

FIRE ALARM CUT SHEETS
Group 4 Architecture Research + Planning CITY OF SACRAMENTO - Martin Luther King, Jr. Library Remodel
PART 1 - Group4 Project No. 23604-01 Back Check Submission November 01, 2024 APENDIX D-2
This Page Intentionally Left Blank

Submitted By IMEG Engineers

6820EVS
Intelligent Fire Alarm Control Panel with Emergency Voice System The 6820EVS is an intelligent addressable Fire Alarm Control Panel combined with an Emergency Voice System (EVS) and are direct replacements for the 5820XL-EVS FACP.

When the EVS features are enabled, they are integrated with the fire alarm and voice evacuation functions of the control panel.

The emergency voice system operations include an onboard supervised microphone. All-call and non-active call buttons can quickly select all active or non-active output groups. The system also allows for emergency messages over fire.

The 6820EVS FACP has one built-in signaling line circuit (SLC), which can support 159 SK detectors and 159 SK modules, or 127 SD protocol devices. Additional SLC loops can be added for a maximum of 1110 (SK) or 635 (SD) points per panel.

The built-in digital alarm communicator/transmitter (DACT) is dual technology, IP and POTS. The POTS transmits system status (alarms, troubles, AC loss, etc.) to a Central Station via the public switched telephone network. The IP communicator’s internet monitoring capability sends alarm signals over the Internet saving the monthly cost of two dedicated business telephone lines. Although not required, the secondary telephone line may be retained providing backup communication over the public switched telephone line. Optional cellular reporting is available.

The 6820EVS has six onboard Flexput® circuits that can be configured as notification outputs or auxiliary power. The 6820EVS also has a form-C trouble relay, and two programmable form-C relays, along with powerful features such as drift compensation, pre- trouble maintenance alert, a built-in sensor test to comply with NFPA 72 calibration testing requirements, and a calibration trouble alert.

A common communications and annunciation link allows up to 17 panels to be connected via copper or fiber optic cable. A designated panel is configured as the communicator for all panels in the link for convenient single-point communications.

FEATURES AND BENEFITS
• Single enclosure for both fire and
emergency voice components
• Ability to select EVS messages as priority
over fire
• 15 Recordable one-minute messages that
can be mapped to eight EVS buttons
• Capable of producing 520 Hz tones to meet
NFPA 72 requirements
• Support for up to 4 LOC consoles and 8
addressable amplifiers
• Expandable SLC loops to 1110 (SK) or 635
(SD) point capacity
• Six Flexput circuits for NAC outputs or
auxiliary power
• Selectable strobe synchronization for
Amseco®, System Sensor®, Wheelock®, and
Gentex® devices
• Built-in DACT with IP and optional cellular
reporting
• Built-in USB interface for quick and easy
programming
• JumpStart® auto programming reduces
installation time
• 999 software zones & 999 output groups
for flexible design options
• 23 preset notification cadence patterns
(including ANSI® 3.41)
• Allows up to 24 SBUS devices
• Four programmable function keys
• Two programmable relays and one fixed
trouble relay
• Compatible with SWIFT® wireless devices
• Convenient field-upgradeable firmware
• Network support for up to 17 sites
• Network card allows copper network
connection with a multi-mode or single-
mode fiber connection
• Real-time clock/calendar with automatic
daylight savings control
• History file with 1,000 event capacity
The 6820EVS panels and accessories provide
features to meet the requirements for Mass
Notification Systems as described in UL 2572
2nd Edition and UL864 10th Edition.

Page 2 of 4 ends

USER INTERFACE

LED INDICATORS
• General Alarm (Red)
• Supervisory (Yellow)
• System Trouble (Yellow)
• System Silenced (Yellow
• System Power (Green)
KEYPAD
• 12-key numeric pad
•A c k n o w l e d g e
• Alarm Silence
•S y s t e m R e s e t
•D r i l l
• F1-F4 Programmable Function Keys

PROGRAMMING
The 6820EVS system offers several options to simplify and expedite programming. JumpStart® auto programming minimizes
programming required to start a new system. The built-in keypad, or the remote annunciators give on-site access to current system programming. System programming can also be accomplished using the Windows®-based Honeywell Fire Software Suite (HFSS).

ORDERING INFORMATION
6820EVS: Addressable fire alarm control panel with emergency voice system, red

COMPATIBLE EVS EQUIPMENT
EVS-50W: 50 Watt amplifier
EVS-125W: 125 Watt amplifier
EVS-100W: 50/100 Watt amplifier
EVS-100WBU: External backup amplifier
EVS-INT50W: 50 /Watt internal amplifier
EVS-CE4: Provides 4 additional audio circuits
EVS-RVM: Remote voice module
EVS-SW24: 24 switch expander
EVS-VCM: Network voice control module
EVS-LOC: Local operator console

COMPATIBLE SBUS DEVICES
6860: 4x40 LCD remote fire annunciator with four programmable buttons, red
5860: 4x20 LCD remote fire annunciator, gray
5860R: 4x20 LCD remote fire annunciator, red
6855: 4x20 LCD remote fire annunciator, red
5865-3: LED annunciators- display up to 30 LEDs (15 red/15 yellow)
5865-4: LED annunciators- display up to 30 LEDs (15 red/15 yellow). Key switches for silence and reset, and a system trouble LED 5880: LED I/O module with 40 programmable LED outputs and eight supervised dry contact inputs
5883: Relay interface. Provides 10 Form C relays
5824: Serial/Parallel printer interface module for printer connection

SK COMPATIBLE ADDRESSABLE DEVICES
Note: SKand SD devices cannot be mixed in the same fire alarm system.

SK-ACCLIMATE: Multi criteria photoelectric smoke detector with thermal 135°F fixed temperature
SK-BEAM: Reflected beam smoke detector without test feature SK-BEAM-T: Reflected beam smoke detector with test feature OSI-RI-SK: Reflected beam smoke detector, SK protocol
SK-CONTROL: Supervised control module
SK-CONTROL-6: Six circuit supervised control module
SK-DUCT: Photoelectric duct smoke detector with extended air speed range
SK-FIRE-CO: Four criteria fire and carbon monoxide detector SK-FIRE-CO-W: Four criteria fire and carbon monoxide detector, white
SK-HEAT: Fixed thermal detector (135°F)
SK-HEAT-W: Fixed thermal detector (135°F), white
SK-HEAT-ROR: Fixed rate of rise detector
SK-HEAT-HT: Fixed high temperature heat detector (190°F) SK-HEAT-HT-W: Fixed high temperature heat detector (190°F), white
SK-HEAT-ROR-W: Fixed rate of rise detector, white
SK-ISO: Fault isolator module
SK-MINIMON: Mini monitor module
SK-MONITOR: Monitor module
SK-MONITOR-2: Dual input monitor module
SK-MON-10: 10- input monitor module
SK-PHOTO: Photoelectric smoke detector
SK-PHOTO-W: Photoelectric smoke detector, white
SK-PHOTO-R: Photoelectric detector with remote test capability SK-PHOTO-R-W: Photoelectric detector with remote test capability, white
SK-PHOTO-T: Photoelectric smoke detector with fixed heat (135°F) SK-PHOTO-T-W: Photoelectric smoke detector with fixed thermal heat (135°F), white
SK-PTIR-W: Multi criteria photoelectric smoke detector with thermal 135°F fixed temperature, white
SK-PULL-SA Addressable single action pull station
SK-PULL-DA: Addressable dual action pull station
SK-RELAY: Addressable relay module
SK-RELAY-6: Addressable Six relay control module
SK-RELAYMON-2: Addressable Dual relay/monitor module
SK-ZONE: Addressable zone interface module
SK-ZONE-6: Six zone interface module
351606:E • 3/7/2022 — Page 3 of 4

SK BASES
B210LP: 6" mounting base
B501: 4" Flangeless mounting base
B200S: Intelligent sounder base
B200S-LF: Low-frequency intelligent sounder base
B224RB: Relay base
B224BI: Isolator base

SD COMPATIBLE ADDRESSABLE DEVICES
Note: SK and SD devices cannot be mixed in the same fire alarm system.

SD505-6AB: Addressable 6" base
SD505-6IB: Addressable 6" short circuit isolator base
SD505-6RB: Addressable 6" relay base
SD505-6SB: Addressable 6" sounder base
SD500-AIM: Addressable input module (switch input)
SD500-ANM: Addressable notification module
SD500-ARM: Addressable relay module
SD505-DTS-K: Remote test switch/LED indicator for the
SD505-DUCTR
SD505-DUCT: Addressable Duct Smoke Detector
SD505-DUCTR: Addressable Duct Detector housing with relay base SD505-HEAT: Absolute temperature heat detector. Trip point range from 135°F–150°F (0°C–37°C)
SD500-LIM: Addressable Line isolator module
SD500-MIM: Addressable Mini input monitor module (switch input) SD505-PHOTO: Photoelectric smoke detector
SD500-PS/-PSDA: Addressable Single or dual action pull station SD500-SDM: Addressable smoke detector module

SWIFT WIRELESS DEVICES
Note: SWIFT is only compatible with System Sensor (SK) devices. It is not compatible with Hochiki (SD) devices.

WSK-WGI: Wireless gateway
WSK-PHOTO: Wireless photoelectric smoke detector with B501W base
WSK-PHOTO-T: Wireless photoelectric smoke detector with fixed thermal detection (135°F) and B501W base
W-SYNC: Wireless sync module
WSK-HEAT: Wireless, fixed heat detector (135°F) with B501W base WSK-HEAT-ROR: Wireless rate-of-rise heat detector and B501W base
WSK-MONITOR: Wireless monitor module
WSK-RELAY: Wireless relay module
WSK-PULL-DA: Wireless pull station
WAV-RL, WAV-WL, WAV-CRL, WAV-CWL: Wireless AV bases
W-USB: Wireless USB radio/antenna dongle that plugs into the USB port of a PC running SWIFT Tools
SWIFT Tools: Programming and diagnostic utility for the wireless gateway and devices. Available for download from
www.farenhyt.com

SYSTEM EXPANDERS
6815: SLC Expander for IDP or SK devices
5815XL: SLC expander for SD devices
RPS-1000: 6A power supply with 6 Flexput circuits & 2 Form C relays
5496: 6 amp NAC power expander with 4 power-limited output ckts

OPTIONAL COMMUNICATORS
CELL-CAB-SK: Cellular communicator, metal enclosure w/lock & key
CELL-MOD: Cellular communicator, plastic enclosure
IPGSM-4G: Dual path fire alarm communicator, cellular and/or IP (primary or backup, selectable)
SK-IP -2: Remote reporting via the Internet. Requires a VisorALARM® receiver at the central station

MISCELLANEOUS ACCESSORIES
SK-NIC: Network Interface Card. Provides a common
communications link for the IFP-300
SK-NIC-KIT: Installation Accessory Kit
SK-FML: Fiber-Optic Multi Mode, transmitter and receiver SK-FSL: Fiber-Optic Single Mode
RBB: Remote battery box accessory cabinet
SK-SCK: Seismic compliance kit used to fasten batteries to the fire panel

SOFTWARE SOLUTIONS
SKST: Silent Knight Selection Tool provides the installer or design architect with a Windows®-based software system configuration tool to create a detailed bill of material (BOM) and battery calculations
HFSS: Honeywell Fire Software Suite provides remote and local panel programming, detector status, event history and additional data. Databases can be uploaded/downloaded via the panel’s USB port using a flash drive. Requires a PC running Microsoft® Windows®.
6820EVS TECHNICAL SPECIFICATIONS
351606 | E | 04/22
©2022 Honeywell International Inc.

Honeywell Silent Knight
12 Clintonville Road
Northford, CT 06472-1610
203.484.7161
www.silentknight.com

Flexput®, Honeywell®, JumpStart®,
Silent Knight®, SWIFT®, and System
Sensor® are registered trademarks
of Honeywell International Inc.

Amseco® is a registered trademark
of Potter Electric Signal Company,
LLC. Gentex® is a registered
trademark of Gentex Corporation.

Hochiki® is a registered trademark
of Hochiki Corporation. Wheelock®
is a trademark of Cooper
Technologies Company. ANSI® is a
registered trademark of the
American National Standards
Institute, Inc. VisorALARM® is a
registered trademark of the Teldat
Corporation. Microsoft® and
Windows® are registered
trademarks of Microsoft
Corporation.

This document is not intended to be
used for installation purposes. We
try to keep our product information
up-to-date and accurate. We cannot
cover all specific applications or
anticipate all requirements. All
specifications are subject to change
without notice.

Country of origin: USA

SYSTEM CAPACITY
Intelligent Signaling Line Circuits: 1
(expandable)
Addressable device capacity: 1110 (SK) or
635 (SD)
Programmable software zones: 999
Output circuits: 6 (expandable)
SBUS devices: 24 (16 annunciators, 8 LED
modules)
LOC units: 4
Addressable amplifiers (total watts): 8
(1000)

ELECTRICAL
AC Power: 120VAC, 60Hz, 3.3A
Standby Current: 190 mA
Alarm Current: 250 mA
Flexput Circuits: Terminal block provides
connections for (six Class B or three Class A)
NACs or auxiliary power. Power-limited,
supervised circuitry. Maximum current per
circuit: 3 A. Cannot exceed 6A total for all
circuits. End-of-line resistor: 4.7k ohm, ½
watt for Class B NACs
Communication Loop: Supervised and
power-limited, Class A or Class B, 32VDC,
150mA
Two Programmable Relays and One Fixed
Trouble Relay: Contact rating: 2.5 A @ 27.4
VDC (resistive), Form C
Battery: Cabinet holds maximum of two 18
AH batteries
Battery Charger Capacity: 7-35 AH

PHYSICAL
Dimensions: 21.6” W x 28.1” H x 5.1” D
(54.9cm W x 71.4cm H x 13.0cm D)
Weight: 50 lbs. (22.7 kg.)
Color: Red

TEMPERATURE AND HUMIDITY
RANGES
This system meets NFPA requirements for
operation at 0 – 49°C (32– 120°F) and at a
relative humidity 93% ± 2% RH (non-
condensing) at 32°C ± 2°C (90°F ± 3°F).

However, the useful life of the system's
standby batteries and the electronic
components may be adversely affected by
extreme temperature ranges and humidity.

Therefore, it is recommended that this
system and its peripherals be installed in an
environment with a normal room
temperature of 15 – 27° C/60 – 80°F.

STANDARDS AND CODES
The 6820 complies with the following
standards and codes:

NFPA 72
NFPA 13
NFPA 15
NFPA 16
NFPA 70
UL 864 10th Edition
UL2572 2nd Edition
Central station; remote Signaling; Local
Protective Signaling Systems; Auxiliary
Protected Premises Unit; Water Deluge
releasing service. Suitable for automatic,
manual, waterflow, sprinkler supervisory
(DACT non-coded) signaling services

AGENCY LISTINGS AND

APPROVALS
UL Listed: S2766
CSFM: 7165-0559:0500
FDNY: COA# 6249
FM: Approved
Seismic: (CA) VMA-45894-05C:

LISTING No.: 7165-0559:0500
CATEGORY: 7165 - FIRE ALARM CONTROL UNIT (COMMERCIAL)
LISTEE: SILENT KNIGHT SECURITY One Fire-Lite Place, Northford, CT, 06472 Contact: Brant,Lisa (203) 484-6277 (203) 484-7309
Email: [email protected]
DESIGN:

Silent Knight Model 6820 and 6820-EVS, Fire Alarm Control Unit, automatic, manual, local, remote station (PPU), central station (PPU), releasing (water deluge only) and mass notification services (6820- EVS). *The CELL-MOD and CELL-CAB-SK have the option to be configured by a compatible control unit for the following pathways: Cellular only without a backup path, primary Cellular communication path, or secondary Cellular communication path.

Model 6820 System Components:

5860 Remote Annunciator
6855 Remote Annunciator
6860 Remote Annunciator
5496 NAC Expander
5880 LED I/O Module
5865-3 Remote LED Annunciator
5865-4 Remote LED Annunciator
5883 Relay Interface
5824 Serial/Paralell Printer Interface Module
5895XL Power Supply
SK-NIC Network Inerface Card
SK-FML Mulit Mode Fiber Card
SK-FSL Single Mode Fiber Card
CELL-MOD Celullar Communicator in Plastic Enclosure
CELL-CAB-SK Cellular Communicator in Metal Enclosure with Lock & Key RBB Remote Battery Box (16"WX10"HX6"D)
SK-SKC Seismic Complaince Kit
5815XL SLC Expander

Page 1 of 3 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE
6815 SLC Expander

Model 6820EVS System Components:

EVS-50W 50 Watt Amplifier
EVS-100W 100 Watt Amplifier
EVS-125W 125 Watt Amplifier
EVS-100WBU External Backup Amplifier
EVS-INT50W 50 Watt Internal Amplifier
EVS-CE4 Circuit Audio Expander
EVS-SW24 24 Switch Expander
EVS-VCM Voice Control Module
EVS-LOC Local Operator Control
5860 Remote Annunciator
6855 Remote Annunciator
6860 Remote Annunciator
5496 NAC Expander
5880 LED I/O Module
5865-3 Remote LED Annunciator
5865-4 Remote LED Annunciator
5883 Relay Interface
5824 Serial/Paralell Printer Interface Module
5895XL Power Supply
SK-NIC Network Inerface Card
SK-FML Mulit Mode Fiber Card
SK-FSL Single Mode Fiber Card
CELL-MOD Celullar Communicator in Plastic Enclosure
CELL-CAB-SK Cellular Communicator in Metal Enclosure with Lock & Key RBB Remote Battery Box (16"WX10"HX6"D)
SK-SCK Seismic Complaince Kit
5815XL SLC Expander

Page 2 of 3 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE
6815 SLC Expander

SK-NIC-KIT
RATING:

Primary Operating Power Supply:
120VAC, 60HZ, 3.25A

Secondary Operating Power Supply:
24VDC, 750 mA, 55Ah
INSTALLATION:

In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction.

MARKING:

Listee's name, model number, electrical rating, and UL label.

APPROVAL:

Listed as a commercial fire alarm control unit for use with separately listed initiating and indicating devices and for mass notication. Refer to listee’s Installation Instruction Manual for details.

NOTES:

This listing is based upon technical data submitted by the applicant. OSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other suitable information sources.

Date Issued: 05/03/2024 Listing Expires: 06/30/2025
Authorized By: David Castillo, Program Coordinator
Fire Engineering & Investigations Division
*Rev 10-02-19 gt

Page 3 of 3 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE

FEATURES & BENEFITS
• Four line LCD display
wi
th 40 characters per
line; 160 characters
provides ample space
for communicating
operating messages
•
Lar
ger keypad buttons
makes it easier to
maneuver for system
reset and silencing
•
Ini
tiate and end fire
drills with a single key
press
•
Eas ily view current
status by alarms,
supervisories, or
troubles
•
On-
board piezo
sounder audibly
indicates alarms,
troubles, and
supervisories
•
Use
s the RS-485
SBUS to interface with
the panel
•
Fiv e status LEDs make
it easier to monitor
and respond to status
changes. They include:

Alarm, Supervisory,
Silence and AC Power
indicators.
•
Acc
ommodates wiring
lengths up to 6000 ft.
from the control panel
for added design and
install flexibility
•
Sys tem access
through a user code or
firefighter's key
•
Supp
ort for
simultaneous use of
multiple 6860s
•
Can b
e flush or
surface mounted. Trim
ring available for
surface mounting.
•
Fou r programmable
function keys for for
improved efficiencies
and time-savings;
frees-up time spent at
the panel
•
Comf
ortable tactical
feel and clear audible
confirmation supports
accurate
programming and
easy operation
6860
Remote Annunciator
The 6860 remote annunciator can be used to view system status indicators for Honeywell Silent Knight fire alarm control panels (FACPs) from anywhere within the system. It provides a convenient way to view system status indicators.

The 6860 comes in a locked, key controlled cabinet - combining security with easy access. It does not require a code or firefighter's key to silence or reset a panel, and also has convenient separate scroll buttons for alarm, supervisory and trouble conditions. The remote annunciator communicates with the main fire alarm control panel through an RS-485 connection.

The 6860 has a large 160 character, 4 x 40 display and four programmable buttons. These features provide more options for set-up and operation when compared to similar remote annunciators.

The 6860 can be surface or flush mounted. The RA-100TR trim ring can be used for surface mounts.

COMPATIBILITY
The 6860 is compatible with the following Honeywell Silent Knight FACPs:
• 682
0: Addressable fire alarm control panel with up to 1,110 addressable points
• 682
0EVS: Addressable fire alarm control panel with an emergency voice system, up to 1,110 addressable points
• 680
8: Addressable fire alarm control panel with up to 198 addressable points
• 670
0: Addressable fire alarm control panel with up to 100 addressable points
6860
For a complete listing of all
compliance approvals and
certifications, please visit
www.silentknight.com .

Microsoft, Windows, and
the Windows Logo are
registered trademarks
or trademarks of
Microsoft Corporation.

Silent Knight® and
Honeywell® are registered
trademarks of Honeywell
International, Inc.

This document is not
intended to be used for
installation purposes. We
try to keep our product
information up-to
date and accurate. We
cannot cover all specific
applications or anticipate
all requirements. All
specifications are subject
to change without notice.

For Technical Support,
call 800-446-6444.
6860 Technical Specifications

PHYSICAL
Flush Mount
Outside wall: 12.25”W x 11.5”H x 7/8”D (31.1W x

29.2H x 2.2D cm)
Inside wall: 9-3/8”W x 8-3/8”H x 2”D (23.8W x

21.3H x 5.1D cm)
Surface Mount: (Including Trim Ring) 12.25”W x

11.5”H x 3”D (31.1W x 29.2H x 2.2D cm)

ENVIRONMENTAL
Operating Temperature: 32°F to 120°F (0°C to
49°C)
Humidity: 0 to 93% relative humidity (non-
condensing)

ELECTRICAL
Operating Voltage: 24VDC
Standby Current: 25mA
Alarm Current: 50mA

ORDERING INFORMATION
6860: Remote Annunciator. Four line (4x40) LCD
annunciator. Red

ACCESSORIES
RA-100TR: Red surface mount trim ring

AGENCY LISTINGS AND APPROVALS
UL listed
CSFM # 7165-0559:0500
NFPA 72
FM approved
FDNY COA approved
351612| A| 11/17
© 2017 Honeywell International Inc.

For more information
Learn more about Silent Knight’s 6860 and other
products available by visiting www.SilentKnight.com
Honeywell Silent Knight
12 Clintonville Road
Northford, CT 06472-1610
800.328.0103
www.honeywell.com
6860 FEATURES
LISTING No.: 7165-0559:0500
CATEGORY: 7165 - FIRE ALARM CONTROL UNIT (COMMERCIAL)
LISTEE: SILENT KNIGHT SECURITY One Fire-Lite Place, Northford, CT, 06472 Contact: Brant,Lisa (203) 484-6277 (203) 484-7309
Email: [email protected]
DESIGN:

Model 6820 System Components:

Page 1 of 3 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE
6815 SLC Expander

Model 6820EVS System Components:

Page 2 of 3 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE
6815 SLC Expander

SK-NIC-KIT
RATING:

Primary Operating Power Supply:
120VAC, 60HZ, 3.25A

Secondary Operating Power Supply:
24VDC, 750 mA, 55Ah
INSTALLATION:

In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction.

MARKING:

Listee's name, model number, electrical rating, and UL label.

APPROVAL:

NOTES:

Date Issued: 05/03/2024 Listing Expires: 06/30/2025
Authorized By: David Castillo, Program Coordinator
Fire Engineering & Investigations Division
*Rev 10-02-19 gt

Page 3 of 3 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE

FEATURES & BENEFITS
• UL Listed for 6 amps
of
notification power
• Pow
er supply’s
advanced switch mode
design reduces
damaging heat and
manages power up to
50% more efficiently
than other systems
•
24 VD
C filtered output
voltage
• Buil t-in
synchronization for
appliances from
Gentex, AMSECO,
System Sensor, and
Wheelock
•
Fou
r power-limited
notification outputs; 2
Class A or 4 Class B, or
1 Class A and 2 Class
B
•
NAC s are
programmable as
notification appliance
circuits, or as auxiliary
power to be used as
constant, resettable,
or door holder power
•
3 amp
s per output
circuit
• Grou
nd fault detector
• CSF
M approved
• Com municates to the
FACP via 4-wire SBUS
(wire runs up to 6000
ft)
•
AC lo
ss delay option
shuts off power to
non-essential high
current accessories
like magnetic door
holders
•
MEA
approved
• Ligh tweight design
adds to ease of
installation and
reduces shipping
costs
•
ANS
I Cadence pattern
output capability
built-in
•
UL 86
4 & 1481 listed
• OSH

PD (CA)
OSP-0065-10 (see
accessories)
5496
Intelligent Power Module
The 5496 intelligent power module is the most cost-effective power supply available today. It delivers 6 amps of notification appliance circuit power and built-in synchronization for appliances from System Sensor®,Gentex®, AMSECO, and Wheelock®. The 5496’s advanced microprocessor design is years ahead of the competition. Its switch mode power supply design is up to 50% more efficient than competitive linear mode power supplies.

The 5496 is a 6 amp notification power expander that provides its own AC power connection, battery charging circuit, and backup battery for use with the Honeywell Farenhyt series fire alarm control panels (FACPs). The 5496 is the cost-effective solution for powering notification appliances required by the Americans with Disabilities Act (ADA). The 5496 has built-in ANSI cadence pattern. The output circuits can be programmed as notification appliance circuits, or as auxiliary power (configurable for constant, resettable, or door holder power).

COMPATIBILITY
The 5496 is compatible with the following FACPs:
• IFP
-2100ECS / IFP-2100ECSB
• IFP
-2100 / IFP-2100B / RFP-2100 / RFP-2100B
• IFP
-2000 / RPS-2000 / IFP-2000ECS
• IFP
-300 / IFP-300B / IFP-300ECS / IFP-300ECSB
• IFP
- 1000 / IFP- 1000ECS
• IFP
-10 0 / IFP-10 0EC S
• IFP
-75
• IFP-
50 5496
For a complete listing of all
compliance approvals and
certifications, please visit
www.farenhyt.com .

Microsoft, Windows, and
the Windows Logo are
registered trademarks
or trademarks of
Microsoft Corporation.

Gentex® is a Registered
Trademark of Gentex
Corporation. Wheelock® is
a Registered Trademark
of Wheelock, Inc.

SWIFT®, Honeywell®,
and System Sensor®are
registered trademarks
of and Farenhyt™ is a
trademark of Honeywell
International, Inc.

For Technical
Support, Please call
800-446-6444.
5496 Technical Specifications

PHYSICAL
Overall Dimensions: 16" H x 12.25" W x 3" D (40.6 x

30.9 x 7.6 cm)
Shipping Weight: 8.7lbs

ENVIRONMENTAL
Operating Temperature: 32°F to 120°F (0°C to
49°C)
Humidity: 10 to 93% relative humidity (non-
condensing)
ELECTRICAL:

AC Input: 120VAC at 2.7A
Output: 24VDC at 6A
Standby & Alarm Current: 10mA
Notification/Aux. Power Circuits: 4
Output Configuration:
2 Class A (Style Z)
4 Class B (Style Y)
1 Class A & 2 Class B
Amps Per Output Circuit: 3.0 (6.0 amps total)
Notification Circuit Output: 20.4 – 27.3VDC @

3.0A each
End-of-Line Resistance: 4.7k W EOL resistor
required on each Class B circuit
Battery Charging Capacity: 7 .0 – 35.0AH

ORDERING INFORMATION
5496: Intelligent Power Module

ACCESSORIES
RBB: Remote Battery Box Accessory Cabinet. 16”
W x 10” H x 6” D (406 mm W x 254 mm H x 152 mm
D)
SK-SCK: Seismic Compliance Kit

AGENCY LISTINGS AND APPROVALS
• CSFM approved
• NFPA
72 • UL li
sted
• FM a
pproved
• Cit
y of NY: 429-90-E Vol XIV
Doc 350302 | Rev G| 11/17
© 2017 Honeywell International Inc.

For more information
Learn more about Honeywell’s Farenhyt Series and
other products available by visiting
www.farenhyt.com
Honeywell Security & Fire
12 Clintonville Road
Northford, CT 06472
800-328-0103

LISTING No.: 7300-0559:0171
CATEGORY: 7300 - FIRE ALARM CONTROL UNIT ACCESSORIES/MISC. DEVICES LISTEE: SILENT KNIGHT SECURITY One Fire-Lite Place, Northford, CT, 06472 Contact: Brant, Lisa 2034846105
Email: [email protected]
DESIGN:

Model 5496 Intelligent power module.

The power module consists of the following:

Model 054960; main board
Model 122599; enclosure
Model SK-F485C; fiber to sbus converter
Refer to listee's data sheet for additional detailed product description and operational considerations.

RATING:
120 VAC
INSTALLATION:

In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction.

MARKING:

Listee's name, model number, electrical rating, and UL label.

APPROVAL:

Listed as a power module for use with listee's Models 5820XL and IFP-1000 (CSFM No. 7165-0559-135), 5808 and IFP-100 (CSFM No. 7165-0559-142), IFP-50 and 5700 (CSFM No. 7165-0559-144), IFP-100ECS and IFP-1000ECS (CSFM No. 7165-0559- 169) fire alarm control units. Refer to listee’s Installation Instruction Manual for details.

NOTES:
03-06-13 gt

Page 1 of 2 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE
This listing is based upon technical data submitted by the applicant. OSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other suitable information sources.

Date Issued: 05/02/2024 Listing Expires: 06/30/2025
Authorized By: Michael Huang, Program Coordinator
Fire Engineering & Investigations Division

Page 2 of 2 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE
EVS-50W
Intelligent 50 Watt Amplifier
Since the EVS-50W is designed as a self-contained distributed amplifier, it can be conveniently located near the area of protection to reduce wiring demands.

Each EVS-50W is capable of producing 50-watts of audio power. Up to four EVS-50W amplifiers can be used on the Emergency Voice System.

The EVS-50W has its own power supply with battery backup and four speaker circuits which can be expanded to eight speaker circuits using the optional EVS-CE4. The EVS-50W is fully supervised by the main panel to identify the trouble conditions.

INSTALLATION
The user-friendly installation does not require special programming or a separate dialer capture module. The EVS-50W can be surface- or flush-mounted.

COMPATIBILITY
The EVS-50W is compatible with the 6820EVS FACP Emergency Voice System.

FEATURES AND BENEFITS
• Complies with UL 864 10th Edition and UL
2572 2nd Edition Standards
• Meets NFPA 72 code compliant for sole,
primary, or backup communications
• Provides SBUS addressable, up to four EVS-
50W amplifiers per system for a total of 500
watts
•E a c h
EVS-50W amplifier is supervised and
has four onboard audio circuits expandable
to eight with the
EVS-CE4 expander for a
system total of 32 audio circuits
• Uses an easy-to-install wire harness to
connect the EVS-CE4 audio circuit
expander
• Extends remote installations up to 6,000
feet away from the EVS-Series panel
• Includes its own power supply and backup
battery
• Selectable for 25V or 70.7V operation
• Provides six-wire connection to the EVS
System:
- Two-wires for the voice bus connections
- Four-wires for the SBUS connections
• Available in a red cabinet can be surface- or
flush-mounted
The EVS-50W is an amplifier compatible with
the Silent Knight Emergency Communication
System. The EVS-50W is used to amplify
audio messages for distribution throughout
entire facilities.

EVS-50W TECHNICAL SPECIFICATIONS
350605 | E | 04-22
©2022 Honeywell International Inc.

Honeywell® and Silent Knight® are
registered trademarks of Honeywell
International, Inc.

Country of origin: U.S.A.

Honeywell Silent Knight
12 Clintonville Road
Northford, CT 06472-1610
203.484.7161
www.silentknight.com

PHYSICAL
Flush Mount Dimensions:

14.05”W x 24.75”H x 3.04”D
(36.08 W x 62.09 H x 8.07 D cm)
Overall Dimensions:

16.0”W x 26.25”H x 4.01”D
(40.06 W x 66.07 H x 10.05 D cm)
Color: Red

ENVIRONMENTAL
Operating Temperature: 32°F to 120°F
(0°C to 49°C)
Humidity:10% to 93% relative humidity
(non-condensing)

ELECTRICAL
Primary AC: 120 VAC @ 60Hz
Standby Current: 85mA @ 25 Vrms;
100mA @ 70.7Vrms
Alarm Current: 525mA @ 25 rms;
580mA @ 70.7Vrm
Total Power: 50W @ 25 Vrms or 70.7Vrms
- Circuit 1-4: Rated at 50W each
- EVS-CE4 Circuits 5-8: Rated at 50W
Main EVS Panel SBUS:

Standby Current: 10mA
Alarm Current: 10mA
Battery Charging Capacity: 7 – 35AH
Battery Size: 18AH max allowed in cabinet.

Use RBB accessory cabinet for larger
batteries up to 35AH per system
Voice Integration Wiring:
-Six conductor
-Two voice bus
-Four SBUS

ORDERING INFORMATION
EVS-50W: Intelligent 50 Watt Amplifier, red

OPTIONAL ACCESSORIES
EVS-CE4: Audio Circuit Expander
RBB: Remote Battery Box accessory
cabinet. Use for backup batteries up to
35AH and too large to fit into a cabinet
SK-SCK: Seismic Compliance Kit

STANDARDS AND CODES
The EVS-50W complies with the following
standards and codes.
• UL 864, 10th Edition: Standard for Control
Units for Fire Alarm Systems
• UL 864, Local Protective and Signaling
Systems
• UL 2572, 2nd Edition: Standard for Mass
Notification Systems
• UL 1711
•N F P A :
- NFPA 13
- NFPA 70
- NFPA 72
• Local Protective Signaling Systems
• Emergency Communication Systems

AGENCY LISTINGS AND

APPROVALS
• UL Listed: S2766
• CSFM Approved: 7165-0559:0500
• FDNY: Approved
LISTING No.: 7165-0559:0500
CATEGORY: 7165 - FIRE ALARM CONTROL UNIT (COMMERCIAL)
LISTEE: SILENT KNIGHT SECURITY One Fire-Lite Place, Northford, CT, 06472 Contact: Brant,Lisa (203) 484-6277 (203) 484-7309
Email: [email protected]
DESIGN:

Model 6820 System Components:

Page 1 of 3 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE
6815 SLC Expander

Model 6820EVS System Components:

Page 2 of 3 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE
6815 SLC Expander

SK-NIC-KIT
RATING:

Primary Operating Power Supply:
120VAC, 60HZ, 3.25A

Secondary Operating Power Supply:
24VDC, 750 mA, 55Ah
INSTALLATION:

In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction.

MARKING:

Listee's name, model number, electrical rating, and UL label.

APPROVAL:

NOTES:

Date Issued: 05/03/2024 Listing Expires: 06/30/2025
Authorized By: David Castillo, Program Coordinator
Fire Engineering & Investigations Division
*Rev 10-02-19 gt

Page 3 of 3 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE
Space Age Electronics, Inc. 2007
ED0142 LT10127 Rev.B 2/2
Ordering Information:

Part # Description
SSU00645 TC2 32 Point Terminal Cabinet
Speciﬁcations:

The TC2 32 Point Terminal Cabinet is constructed of 16 gauge (.062 thk.) cold rolled steel and ﬁnished with a durable red textured, heat-resistant baked-on enamel ﬁnish. The front cover is engineered with a removable formed lift-a-way hinge and displays “FIRE ALARM TERMINAL CABINET” in 2” white screened indelible lettering. A CAT 30 keyed door lock secures the front cover.

The interior of the box has ﬁeld identiﬁcation labels on the inside cover corresponding to the terminal strip’s labeling inside the back box. Overall dimensions measure 14” wide by 14” high by 3 1/4” deep.

The cabinet includes 1/2”, 3/4”, 1”, 1 1/2” and 2” EMT knockout clusters on the top, bottom and left side. Interior dual 16 point high barrier terminal strips are rated for 12 gauge wire and 20 amp max 250V (Class B/UL) 300V (CSA).
3 1/4”
14”
14”
FIRE
ALARM

TERMINA
L

CABINET
Removable formed
lift-a-way hinge
Terminal Point Identification
back box
clearance from back
plate to back box.
back
plate
drill screw
(self-tapping)
1/2”
Back Plate
Detail
1/2” mounting screw
Agency Approvals:

UOXX.S2580 UL Listed Control Unit Accessories
Space Age Electronics, Inc.
www.1sae.com
800.486.1723 Toll Free
508.485.0966 Local
508.485.4740 Fax
This document is subject to change without notice, see doc # ED0479 for legal disclaimer LISTING No.: 7300-0553:0110
CATEGORY: 7300 - FIRE ALARM CONTROL UNIT ACCESSORIES/MISC. DEVICES LISTEE: SPACE AGE ELECTRONICS 58 Chockett Road, Sterling, MA, 01564 Contact: Scholl, Robert (508) 485-0966 (508) 485-4740
Email: [email protected]
DESIGN:

Models TC2-32, TC1-18, TCX/A 64, TCX/D 128, ACE/A, AC2, ACE/D, IF-2, IF1, IFX/A and IFX/D enclosures. Models ACE-11, ACE-12 and ACE-13, *ACE2424, *ACE 3036, *ACE 2436, *ACE 3048 document cabinets. Refer to listee's data sheet for detailed product description and operational considerations.

RATING:

INSTALLATION:

In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction.

MARKING:

Listee's name, model number and UL label.

APPROVAL:

Listed as fire alarm equipment enclosures and document cabinets for use with listee's fire alarm equipment. Refer to listee’s Installation Instruction Manual for details.

NOTES:

Date Issued: 04/10/2024 Listing Expires: 06/30/2025
Authorized By: David Castillo, Program Coordinator
Fire Engineering & Investigations Division
02-09-16 dc

Page 1 of 1 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE

SK-PHOTO-W SERIES
Addressable Photoelectric Smoke Detectors
The Silent Knight® SK-PHOTO-W Series
feature a modern design and expanded color
options support a variety of contemporary
aesthetic demands. In addition, each detector
is constructed for exceptional installation and
maintenance efficiency.

The SK-PHOTO-W Series intelligent plug-in smoke detectors are designed for both performance and aesthetics, and are direct replacements for the SK-PHOTO Series detectors. A new modern, sleek, contemporary design and enhanced optical sensing chamber is engineered to sense smoke produced by a wide range of combustion sources in accordance with more stringent code standards. The SK-PHOTO-W Series detector sensitivity can be programmed in the control panel software. Sensitivity is continuously monitored and reported to the panel. Point ID capability allows each detector’s address to be set with rotary, decimal address switches, providing exact detector location for selective maintenance when chamber contamination reaches an unacceptable level. Dual electronic thermistors add 135°F (57°C) fixed temperature thermal sensing on the SK-PHOTO-T-W.

The SK-PHOTO-R-W is a remote test capable detector for use with DNR Series duct detector housings.

FEATURES AND BENEFITS
• Designed to meet UL 1268 7th Edition
• Sleek and stylish contemporary design
• Stable communication technique with
noise immunity
• Addressable by device
• Rotary, decimal addressing (Refer to the
Silent Knight panel manuals for device
capacity)
• Two-wire SLC connection
• LEDs blink every time the unit is polled
• 360°-field viewing angle of the visual alarm
indicators (two bi-color LEDs); LEDs blink
green in Normal condition and turn on
steady red in Alarm
• Integral communications and built-in
device-type identification
• Remote test feature from the panel
• Built-in functional test switch activated by
external magnet
• Walk test with address display (an address
of 121 will blink the detector LED 12-
(pause)-1)
• Low standby current
• Built-in tamper-resistant feature
• Designed for direct-surface or electrical-
box mounting
• Sealed against back pressure
• Plugs into separate base for ease of
installation and maintenance
• Expanded color options
• SEMS screws for wiring of the separate base
• Optional remote, single-gang LED
accessory
• Optional sounder, relay, and isolator bases

Page 2 of 3 ends

INSTALLATION
The SK-PHOTO-W Series plug-in intelligent thermal detectors use a separate base to simplify installation, service, and maintenance.

Installation instructions are shipped with each detector.

Mount base (all base types) on an electrical backbox which is at least 1.5" (3.81 cm) deep. For a chart of compatible junction boxes, see SK-61045.

Note: Because of the inherent supervision provided by the SLC loop, end-of-line resistors are not required. Wiring “T-taps” or branches are permitted for Style 4 (Class “B”) wiring.

Note: When using relay or sounder bases, consult the SK-ISO installation sheet I56-3627 for device limitations between isolator modules and isolator bases.

OPERATION
Each SK-PHOTO-W Series detector uses one of the panel’s addresses (total limit is panel dependent) on the Signaling Line Circuit (SLC). It responds to regular polls from the control panel and reports its type and the status. If it receives a test command from the panel (or a local magnet test), it stimulates its electronics and reports an alarm. It blinks its LEDs when polled and turns the LEDs on when commanded by the panel. The
SK-PHOTO-W Series offers features and performance that
represent the latest in smoke detector technology.

PRODUCT LINE INFORMATION
Note: “-IV” suffix indicates ivory color.

SK-PHOTO-W: White, low-profile photoelectric sensor
SK-PHOTO-T-W: White, same as SK-PHOTO-W but includes a
built-in 135°F (57°C) fixed-temperature thermal device
SK-PHOTO-R-W: White, low-profile intelligent photoelectric sensor, remote test capable, for use with DNR/DNRW
B300-6: White, standard flanged low-profile mounting base B300-6-BP: Bulk pack of B300-6, package contains 10
B300-6-IV: Ivory, standard flanged low-profile mounting base B501-WHITE: White, standard European flangeless mounting base
B501-BL: Black, standard European flangeless mounting base B501-IV: Ivory, standard European flangeless mounting base B501-WHITE-BP: Bulk pack of B501-WHITE, contains 10
B200S-WH: White, Intelligent, programmable sounder base B200S-IV: Ivory, Intelligent, programmable sounder base B200SR-WH: White, Intelligent sounder base for retrofit applications B200SR-IV: Ivory, Intelligent sounder base for retrofit applications B200S-LF-WH: White, Low Frequency Intelligent, programmable sounder base
B200S-LF-IV: Ivory, Low Frequency Intelligent, programmable sounder base
B200SR-LF-WH: White, Low Frequency Intelligent sounder base for retrofit applications
B200SR-LF-IV: Ivory, Low Frequency Intelligent sounder base for retrofit applications
B224RB-WH: White, plug-in System Sensor® relay base
B224RB-IV: Ivory, plug-in System Sensor relay base
B224BI-WH: White, plug-in System Sensor isolator detector base B224BI-IV: Ivory, plug-in System Sensor isolator detector base

ACCESSORIES
TR300: White, replacement flange for B210LP or B300-6 bases TR300-IV: Ivory, replacement flange for B210LP or B300-6 bases RA100Z(A): Remote 3 – 32 VDC LED annunciator, mounts to a U.S. single-gang electrical box, for use with B501 and B300-6 bases only
M02-04-00: Test magnet
M02-09-00: Test magnet with telescoping handle
CK300: White, detector color kit, pack of 10
CK300-IV: Ivory, detector color kit, pack of 10
CK300-BL: Black, detector color kit, pack of 10

SK-PHOTO-W SERIES TECHNICAL SPECIFICATIONS
351634 | B | 07/19
©2019 Honeywell International Inc.

Honeywell Silent Knight
12 Clintonville Road
Northford, CT 06472-1610
203.484.7161
www.silentknight.com
Silent Knight® and System Sensor®
are registered trademarks of
Honeywell International, Inc.

Country of origin: Mexico

PHYSICAL/ENVIRONMENTAL
Sensitivity:
- UL Applications: 0.5% to 4.0% per foot
obscuration.
- ULC Applications: 0.5% to 3.5% per foot
obscuration
Size: 2.0" (5.3 cm) high; base determines
diameter
- B300-6: 6.1" (15.6 cm) diameter
- B501: 4" (10.2 cm) diameter
For a complete list of detector bases, see
SK-61045.

Shipping weight: 3.4 oz. (95 g)
Operating temperature range:
• SK-PHOTO-W: 32°F to 122°F (0°C to 50°C)
• SK-PHOTO-T-W: 32°F to 100°F(0°C to
38°C)
• SK-PHOTO-R-W installed in a DNR/DNRW:
-4°F to 158°F (-20°C to 70°C)
UL/ULC Listed Velocity Range: 0-4000 ft/
min. (1219.2 m/min.), suitable for
installation in ducts
Relative humidity: 10% – 93% non-
condensing
Thermal ratings: fixed-temperature set
point 135°F (57°C), rate-of-rise detection
15°F (8.3°C) per minute, high temperature
heat 190°F (88°C)

ELECTRICAL SPECIFICATIONS
Voltage range: 15 - 32 volts DC peak
Standby current (max. avg.): 200µA @ 24
VDC (one communication every 5 seconds
with LED enabled)
Max current: 4.5 mA @ 24 VDC (“ON”)

DETECTOR SPACING AND

APPLICATIONS
Silent Knight recommends spacing
detectors in compliance with NFPA 72. In
low airflow applications with smooth ceiling,
space detectors 30 feet (9.1m). For specific
information regarding detector spacing,
placement, and special applications refer to
NFPA 72. A
System Smoke Detector
Application Guide, document A05-1003, is
available at www.systemsensor.com.

AGENCY LISTINGS AND

APPROVALS
These listings and approvals apply to the
modules specified in this document.In some
cases, certain modules or applications may
not be listed by certain approval agencies, or
listing may be in process.

Consult factory for
latest listing status.
• UL Listed: S6173
• FM Approved
• CSFM: 7272-0559:0512
LISTING No.: 7272-0559:0512
PARENT LISTING No.: 7272-0028:0503
CATEGORY: 7272 - SMOKE DETECTOR-SYSTEM TYPE-PHOTOELECTRIC LISTEE: SILENT KNIGHT SECURITY One Fire-Lite Place, Northford, CT, 06472 Contact: Brant, Lisa 2034846105
Email: [email protected]
DESIGN:

Models IDP-PHOTO-W, IDP-PHOTO-R-W, IDP-PHOTO-T-W, SK-PHOTO-W, SK- PHOTO-R-W, and SK-PHOTO-T-W analog addressable, photoelectric smoke detectors for open area and duct installations. Models IDP-PHOTO-T-W and SK-PHOTO-T-W have complementary heat detectors. All models are similar except for population/depopulation of components on the Printed Wiring Board for the intended features. All above models may be followed by two digit Suffix indicating the color of the detector enclosure: no suffix for white, -IV for ivory, -BL for black. Refer to listee's Installation and Maintenance Instruction for additional detailed product description and operational considerations.

RATING:
24 VDC.

INSTALLATION:

In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction.

MARKING:

Listee's name, model number, electrical rating, and UL label.

APPROVAL:

Listed as photoelectric smoke detectors. Detectors are for use with separately listed System Sensor base Models *B224BI and B224RB (CSFM Listing 7300-1653:0126), *B501, *B210LP (CSFM Listing 7300-1653:0109), B200S and B200SR (CSFM Listing 7300-1653:0213), B200S-LF and B200SR-LF (CSFM Listing 7300-1653:0238), B300- 6 and B300-6-IS bases (CSFM Listing 7300-1653:0109), System Sensor duct detector housings Models DNR and DNRW (CSFM listing 3240-1653:0209), and separately listed compatible fire alarm control units. Refer to manufacturer’s Installation Manual for details. *All models comply with the applicable requirements in ANSI/UL 268, Smoke Detectors for Fire Alarm Systems, 7th Edition, January 11, 2016.

NOTES:

The photoelectric type detectors are generally more effective at detecting slow, smoldering fires that smolder for hours before bursting into flame. Sources of these fire may include cigarettes burning in the couched or bedding. The ionization type detectors are generally more effective at detecting fast, flaming fires that consume combustible materials rapidly and spread quickly. Sources of these fires include paper burning in a waste container or a grease fire in the kitchen.

Page 1 of 2 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE
This listing is based upon technical data submitted by the applicant. OSFM Fire Engineering staff has reviewed the test resultsand/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria.Refer to listee's data sheet, installation instructions and/or other suitable information sources.

Date Issued: 05/08/2024 Listing Expires: 06/30/2025
Authorized By: David Castillo , Program Coordinator
Fire Engineering & Investigations Division
*Revision 12-17-
19 VWW

Page 2 of 2 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE

INTELLIGENT BASES
Standard, Relay, Isolator, Sounder, and Low Frequency Sounder Bases B300-6 Standard 6”
Base (White)
B300-6-IV Standard 6”
Base (Ivory)
B200S-WH Sounder
Base (White)
B200S-LF-WH
Low Frequency
Sounder Base (White)
B501-WHITE Flangeless
4” Base (White)
B501-BL Flangeless
4” Base (Black)
To meet local code and application requirements, Silent Knight® offers standard 4" and 6" bases, as well as specialty base designs including relay, isolator, sounder and low frequency sounder bases that are UL listed for low frequency operation and comply with NFPA 72 requirements for sleeping spaces for the new SK-W Series of addressable detectors as well as previous generations.

The standard 4" and 6" bases offer a plug-in detector base intended for use in intelligent systems, with screw terminals provided for power (+ and –), and remote annunciator connections. Communication takes place over the power (+ and –) lines. The 4" base offers a compact design while the 6" base provides compatibility with a wider range of junction boxes.

The specialty bases support application driven requirements. These bases employ a separate mounting plate that installs on various junction box sizes to eliminate unsightly surface-mount boxes. The mounting plate enables pre-wiring of all connections to speed and simplify installation.

Relay bases (B224RB-WH/B224RB-IV) provide one form-C contact relay for control of auxiliary functions, such as door closure and elevator recall. The relay can operate in two different modes (short and long delay). The activation time for the short delay is 60-100 milliseconds, while the activation time for the long delay is 6-10 seconds. A shunt with pin headers, located on the base PC board, is used to set the delay timing.

Isolator bases (B224BI-WH/B224BI-IV) allow the Signaling Line Circuit (SLC) loop to operate under fault conditions created from a short circuit preventing an entire communication loop from being disabled. The base isolates the section of the loop containing the short circuit from the remainder of the circuit and automatically restores when the fault is corrected.

Sounder and low frequency (-LF) sounder bases are designed for new and existing dwelling unit applications. They offer maximum flexibility in installation, configuration, and operation to meet or exceed UL 268 and UL 464 requirements. The low frequency sounder bases are designed to meet the NFPA 72 sleeping space requirement to produce a fundamental frequency of 520 Hz +/- 10% with a square wave or its equivalent. Studies show that a lower frequency, centered around 520 Hz, is the most ideal to wake sleeping occupants, even those with mild to severe hearing loss.

FEATURES AND BENEFITS
• Bases enable quick and secure detector
plug-in
• SEMS Screws provide easy wiring
connection
• UL 268 compliant
• Support for 12-24 AWG provides
installation flexibility
• Multiple base formats meet application
requirements
• Standard white color with ivory and black
options
• Mechanical locking feature restricts
removal of attached sensor head
• Specialty Base Features:
• Pre-wired mounting plate simplifies
installation
• Application driven feature sets
• Sounder bases both UL268 and UL464
compliant

Page 2 of 3 ends

The B200S sounder and LF sounder bases (B200S-WH/B200S-IV/ B200S-LF-WH/B200S-LF-IV) adopt the same address as the
detector, but use a unique device type on the loop. The Fire Alarm Control Panel (FACP) can use that address to command an individual sounder — or a group of sounders — to activate. The command set from the FACP can be tailored to multiple event- driven tone outputs allowing selection of volume (75 or 85 dBA), tone (ANSI Temporal 3, ANSI Temporal 4, or March Time) and group.

In addition, some FACPs will enable custom tone patterns. The B200S series sounder bases recognize the System Sensor
synchronization protocol. This enables them to be used as a component of the general evacuation signal — along with other System Sensor AV appliances — when connected to a power supply or FACP output capable of generating the System Sensor
synchronization pulses.

The B200SR sounder and LF sounder bases (B200SR-WH/
B200SR-IV/B200SR-LF-WH/B200SR-LF-IV) are fully compatible with existing B501BH Series sounder base installations. The device enables users to select one of two B501-supported tones (ANSI Temporal 3 or Continuous) through a jumper.

PRODUCT LINE INFORMATION

INTELLIGENT BASES
“-IV” suffix indicates Ivory color model.
“-BL ” suffix indicates Black color model.
“-WH” and “-WHITE” suffix indicates White color model.

B300-6: White, 6” base, standard flanged low-profile mounting base; replacement base for the B210LP.

B300-6-BP: Bulk pack of B300-6, package contains 10;
replacement for the B210LPBP.

B300-6-IV: Ivory,6” base, standard flanged low-profile mounting base.

B501-WHITE: White, 4” standard European flangeless mounting base. UL/ULC listed
B501-WHITE-BP: Bulk pack of B501-WHITE, contains 10
B501-BL: Black, 4” standard European flangeless mounting base B501-IV: Ivory color, 4” standard European flangeless mounting base
B224RB-WH: White, relay base
B224RB-IV: Ivory, relay base
B224BI-WH: White, isolator detector base
B224BI-IV: Ivory isolator detector base
B200S-WH: White, Intelligent addressable sounder base capable of producing sound output in high or low volume with ANSI Temporal 3, ANSI Temporal 4, continuous tone, marching tone, and custom tone; Uses SK protocol
B200S-IV: Ivory, Intelligent addressable sounder base capable of producing sound output in high or low volume with ANSI Temporal 3, ANSI Temporal 4, continuous tone, marching tone, and custom tone; Uses SK protocol
B200S-LF-WH: White, Low Frequency Intelligent, programmable sounder base, produces a fundamental frequency of 520 Hz +/- 10% with a square wave or its equivalent; designed to meet the NFPA 72 sleeping space requirement
B200S-LF-IV: Ivory, Low Frequency Intelligent, programmable sounder base, produces a fundamental frequency of 520 Hz +/- 10% with a square wave or its equivalent; designed to meet the NFPA 72 sleeping space requirement
B200SR-WH: White, Intelligent sounder base capable of producing sound output with ANSI Temporal 3 or continuous tone; Intended for retrofit applications
B200SR-IV: Ivory, Intelligent sounder base capable of producing sound output with ANSI Temporal 3 or continuous tone; Intended for retrofit applications
B200SR-LF-WH: White, Low Frequency Intelligent, programmable sounder base, produces a fundamental frequency of 520 Hz +/- 10% with a square wave or its equivalent; designed to meet the NFPA 72 sleeping space requirement; intended for retrofit applications B200SR-LF-IV: Ivory, Low Frequency Intelligent, programmable sounder base, produces a fundamental frequency of 520 Hz +/- 10% with a square wave or its equivalent; designed to meet the NFPA 72 sleeping space requirement. Intended for retrofit applications.

MOUNTING KITS AND ACCESSORIES
TR300: White, replacement flange for B300-6 base
TR300-IV: Ivory, replacement flange for B300-6-IV base
RA100Z: Remote LED annunciator, 3 – 32 VDC, mounts to a U.S. single-gang electrical box; For use with B501 and B300-6 M02-04-00: Test magnet
M02-09-00: Test magnet with telescoping handle
CK300: White, detector color kit, pack of 10
CK300-IV: Ivory, detector color kit, pack of 10
CK300-BL: Black, detector color kit, pack of 10

JUNCTION BOX SELECTION GUIDE
Base Models Single Gang Double Gang 3.5 " Oct. 4.0 " Oct. 4.0 " Square 4.0 " Square with 3.0" mud ring 50 mm 60 mm 70 mm 75 mm B200S,B200SR Yes Yes Yes Yes Yes Yes No No No No
B501 No No Yes No No Yes Yes Yes Yes No
B300-6 Yes No Yes Yes Yes Yes No No No No
B224BI, B224RB Yes Yes Yes Yes Yes Yes No No No No
Box depth contingent on base and wire size.

Refer to National Electric Code or applicable local codes for appropriate recommendations.

Applies to all model variants “BL ”, “-LF”, “-IV”, “-WH”, and “-WHITE”. See Product Line Information for detailed model description.

INTELLIGENT BASES TECHNICAL SPECIFICATIONS
SK-61045 | B | 07/19
©2019 Honeywell International Inc.

Honeywell Silent Knight
12 Clintonville Road
Northford, CT 06472-1610
203.484.7161
www.silentknight.com
Silent Knight® and System Sensor®
are registered trademarks of
Honeywell Inc.

Country of origin: Mexico

ELECTRICAL
For B300-6 Series bases:
• Operating voltage: 15 to 32 VDC
• Standby current: 170 µA maximum
For B501 Series bases:
• Operating voltage: 15 to 32 VDC
• Standby current: 150 µA maximum
For B200 Series bases:
• External supply voltage: 16 to 33 VDC (FWR)
• Standby current: 500 µA maximum
• Alarm current for B200S(-IV)(-WH):
35 mA maximum at high-volume setting
15 mA maximum at low-volume setting
• Alarm current for B200S-LF(-IV)(-WH) High-
volume setting:
70 mA maximum @ 33.0 VDC
90 mA maximum @ 24.0 VDC
140 mA maximum @16.0 VDC
• Alarm current for B200S-LF(-IV)(-WH) Low-
volume setting:
15 mA maximum @ 33.0 VDC
20 mA maximum @ 24.0 VDC
25 mA maximum @ 16.0 VDC
• Alarm current for B200SR(-IV)(-WH): 35 mA
maximum
• Alarm current for B200SR-LF(-IV)(-WH):
65 mA maximum @ 33.0 VDC
90 mA maximum @ 24.0 VDC
125 mA maximum @16.0 VDC
SLC operating voltage: 15 to 32 VDC
SLC standby current: See applicable sensor
specification
Sound output: Greater than 85 dBA minimum;
measured in a UL reverberant room at 10 feet,
24 Volts (continuous tone)
For B224BI, B224RB (-IV) (-WH) bases:
• Operating voltage: 15 to 32 VDC (powered by
SLC)
• Standby ratings: <450 µA maximum @ 24 VDC
• Set time: (B224RB(-IV)(-WH) only): short
delay 60-100 msec; long delay 6-10 seconds
• Reset time: (B224RB/-IV/-WH only): 20
milliseconds maximum
• Relay characteristics: (B224RB/-IV/-WH
only):
two-coil latching relay; one Form-C
contact; ratings (UL/CSA): 0.9 A @ 125 VAC,

0.9 A @ 110 VDC, and 3.0 A @ 30 VDC

PHYSICAL
Note: Specifications applies to all model variants
“-BL ”, “-LF”, “-IV”, -WH, -WHITE. See Product Line
Information for detailed model description.

Diameter:
• B501-WHITE: 4" (10.16 cm)
• B300-6, : 6.1" (15.49 cm)
• B224BI, B224RB: 6.2" (15.748 cm)
• B200S, B200SR: 6.875" (17.46 cm)
Wire gauge:
• B224BI, B224RB: 14 to 24 AWG
• B300-6, B501, B200S, B200SR12 to 24 AWG
Temperature range:
• B224BI, B224RB, B200S, B200SR: 32°F to
120°F (0°C to 49°C)
• B300-6, B501: -4°F to 150°F (-20°C to 66°C)
Humidity range: 10% to 93% RH, non-
condensing
System temperature and humidity ranges:

This system meets NFPA requirements for oper-
ation at 0°C to 49°C (32°F to 120°F); and at a
relative humidity (non-condensing) of 85% at
30°C (86°F) per NFPA, and 93% ± 2% at 32°C ±
2°C (89.6°F ± 1.1°F) per ULC. However, the use-
ful life of the system’s standby batteries and the
electronic components may be adversely
affected by extreme temperature ranges and
humidity. Therefore, it is recommended that this
system and all peripherals be installed in an
environment with a nominal room temperature
of 15°C to 27°C (60°F to 80°F).

AGENCY LISTINGS AND

APPROVALS
The listings and approvals below apply to
intelligent bases as noted. In some cases,
certain modules or applications may not be
listed by certain approval agencies, or listing
may be in process. Consult factory for latest
listing status.

UL Listed: S911
FM Approved
CSFM: 7300-1653:0109, 7300-1653:0126,
7300-1653:0213, 7300-1653:0238
LISTING No.: 7300-1653:0109
CATEGORY: 7300 - FIRE ALARM CONTROL UNIT ACCESSORIES/MISC. DEVICES LISTEE: System Sensor, Unincorporated Div of Honeywell Int'l Inc. 3825 Ohio Ave, St. Charles, IL, 60174
Contact: Brant, Lisa 2034846105
Email: [email protected]
DESIGN:

Models B401, B401B, B401R, B401BR, B401BR-750, B401R-750, B402B, B404B, B404BT, B406B, B501, B501B, 14506587-002, B501BH, B501BHT, B401BH, B110LP, B110RLP, B110RLP750, B112LP, B114LP, B114LPBT, B116LP, B210LP, B501-BL, B501- IV, *B501-WHITE, B300-6, B300-6-IV, B300-6-IS detector bases. Refer to listee's data sheet for detailed product description and operational considerations.

RATING:

INSTALLATION:

In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction.

MARKING:

Listee's name, *model number, *electrical rating and UL label.

APPROVAL:

Listed as detector bases for use with separately listed compatible detectors. *Refer to Manufacturers Installation Instruction Manual for details.

NOTES:

Formerly 7300-1209:128
This listing is based upon technical data submitted by the applicant. OSFM Fire Engineering staff has reviewed the test results and/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria. Refer to listee's data sheet, installation instructions and/or other suitable information sources.

Date Issued: 04/30/2024 Listing Expires: 06/30/2025
Authorized By: David Castillo, Program Coordinator
Fire Engineering & Investigations Division
*Rev 04-03-18 gt

Page 1 of 1 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE
Agency Listings
Features
• Plug-in design with minimal intrusion into the back box • Tamper-r
esistant construction
• Automatic selection of 12- or 24-volt operation at 15 and 15/75 candela
• Field-selectable candela settings on ceiling units: 15, 15/75, 30, 75, 95, 110, 115, 135, 150, 177, and 185
• Horn rated at 88+ dBA at 16 volts
• Rotary switch for horn tone and thr
ee volume selections
• Universal mounting plate for ceiling units
• Mounting plate shorting spring feature checks wiring continuity befor
e device installation
• Electrically Compatible with legacy SpectrAlert devices • Compatible with MDL3 sync module
• Listed for ceiling or wall mounting
The SpectrAlert Advance series of
fers the most versatile and
easy-to-use line of horns, strobes, and horn strobes in the industry.

With white and red plastic housings, wall and ceiling mounting options, and plain and FIRE-printed devices, SpectrAlert Advance can meet virtually any application requirement.

Like the entire SpectrAlert Advance product line, ceiling-mount strobes and horn strobes include a variety of features that increase their application versatility while simplifying installation. All devices feature a plug-in design with minimal intrusion into the back box, making installations fast and foolproof while virtually eliminating costly and time-consuming ground faults.

To further simplify installation, SpectrAlert Advance utilizes a universal mounting plate so you can mount them to a wide array of back boxes. With an onboard shorting spring, installers can test wiring continuity before the device is installed.

Installers can also easily adapt devices to a suit a wide range of application requirements using field-selectable candela settings, automatic selection of 12- or 24-volt operation, and a rotary switch for horn tones with three volume selections.

Indoor Selectable-
Output Strobes and
Horn Strobes for

Ceiling Applications
SpectrAlert® Advance audible visible notification products are rich with features guaranteed to cut installation times and maximize profits.

MEA452-05-E3023572
7125-1653:0186 (indoor strobes)
7125-1653:0188 (horn strobes,
chime str
obes)
7135-1653:0189 (horns, chimes)
S4011 (chimes, horn strobes, horns)
S5512 (strobes)

AVDS10101
SpectrAlert Advance Specifications
Architect/Engineer Specifications
General
SpectrAlert Advance strobes and horn strobes shall mount to a standard 4 × 4 × 1½-inch back box, 4-inch octagon back box, or double- gang back box. Two-wire products shall also mount to a single-gang 2 × 4 × 17⁄8-inch back box. A universal mounting plate shall be used for mounting ceiling and wall products. The notification appliance circuit wiring shall terminate at the universal mounting plate. Also, SpectrAlert Advance products, when used with the Sync•Circuit
™ Module accessory, shall be powered from a non-coded notification appliance circuit output and shall operate on a nominal 12 or 24 volts. When used with the Sync•Circuit Module, 12-volt-rated notification appliance circuit outputs shall operate between 8.5 and 17.5 volts; 24-volt-rated notification appliance circuit outputs shall operate between 16.5 and 33 volts. Indoor SpectrAlert Advance products shall operate between 32 and 120 degrees Fahrenheit from a regulated DC or full-wave rectified unfiltered power supply. Strobes and horn strobes shall have field-selectable candela settings including 15, 15/75, 30, 75, 95, 110, 115, 135, 150, 177, and 185.

Strobe
The strobe shall be a System Sensor SpectrAlert Advance Model _______ listed to UL 1971 and shall be approved for fire protective service.

The strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances, flashing at 1 Hz over the strobe’s entire operating voltage range. The strobe light shall consist of a xenon flash tube and associated lens/reflector system.

Horn Strobe Combination
The horn strobe shall be a System Sensor SpectrAlert Advance Model _______ listed to UL 1971 and UL 464 and shall be approved for fire protective service. The horn strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances, flashing at 1 Hz over the strobe’s entire operating voltage range. The strobe light shall consist of a xenon flash tube and associated lens/reflector system. The horn shall have three audibility options and an option to switch between a temporal three pattern and a non-temporal (continuous) pattern. These options are set by a multiple position switch. On four-wire products, the strobe shall be powered independently of the sounder. The horn on horn strobe models shall operate on a coded or non-coded power supply.

Synchronization Module
The module shall be a System Sensor Sync•Circuit model MDL3 listed to UL 464 and shall be approved for fire protective service. The module shall synchronize SpectrAlert strobes at 1 Hz and horns at temporal three. Also, while operating the strobes, the module shall silence the horns on horn strobe models over a single pair of wires. The module shall mount to a 4 11⁄16 × 4 11⁄16 × 2 1⁄8-inch back box. The module shall also control two Style Y (class B) circuits or one Style Z (class A) circuit. The module shall synchronize multiple zones. Daisy chaining two or more synchronization modules together will synchronize all the zones they control. The module shall not operate on a coded power supply.

Physical/Electrical Specifications
Standard Operating Temperature 32°F to 120°F (0°C to 49°C) Humidity Range 10 to 93% non-condensing
Strobe Flash Rate 1 flash per second
Nominal Voltage Regulated 12 DC/FWR or regulated 24 DC/FWR 1 Operating Voltage Range2 8 to 17.5 V (12 V nominal) or 16 to 33 V (24 V nominal) Operating Voltage Range (MDL3) 8.5 to 17.5V (12 V nominal) or 16.5 to 33 V (24V nominal) Input Terminal Wire Gauge 12 to 18 AWG
Ceiling-Mount Dimensions (including lens) 6.8" diameter × 2.5" high (173 mm diameter × 64 mm high) Ceiling-Mount Surface Mount Back Box Skirt Dimensions
(SBBCR, SBBCW)

6.9" diameter x 3.4" high (175 mm diameter x 86 mm high) Notes:

1. Full Wave Rectified (FWR) voltage is a non-regulated, time-var ying power source that is used on some power supply and panel outputs.

2. P, S, PC, and SC products will operate at 12 V nominal only for 15 and 15/75 cd.

AVDS10101
Horn Strobe Output (dBA)
Switch
Position Sound Pattern dB
8–17 .5
Volts
16–33
Volts
24-Volt Nominal
Reverberant Anechoic

DC FWR DC FWR DC FWR DC FWR
1 Temporal High 78 78 84 84 88 88 99 98
2 Temporal Medium 74 74 80 80 86 86 96 96
3 Temporal Low 71 73 76 76 83 80 94 89
4 Non-Temporal High 82 82 88 88 93 92 100 100
5 Non-Temporal Medium 78 78 85 85 90 90 98 98
6 Non-Temporal Low 75 75 81 81 88 84 96 92
7 † Coded High 82 82 88 88 93 92 101 101
8† Coded Medium 78 78 85 85 90 90 97 98
9† Coded Low 75 75 81 81 88 85 96 92
†Settings 7, 8, and 9 are not available on 2-wire horn strobes.

UL Max. Strobe Current Draw (mA RMS)
Candela
8–17 .5 Volts 16–33 Volts

DC FWR DC FWR
Standard Candela Range 15 123 128 66 71
15/75 142 148 77 81
30 NA NA 94 96
75 NA NA 158 153
95 NA NA 181 176
110 NA NA 202 195
115 NA NA 210 205
High
Candela Range
135 NA NA 228 207
150 NA NA 246 220
177 NA NA 281 251
185 NA NA 286 258
UL Max. Current Draw (mA RMS), 2-Wire Horn Strobe, Standard Candela Range (15–115 cd) DC Input
8–17 .5 Volts 16–33 Volts
15 15/75 15 15/75 30 75 95 110 115
Temporal High 137 147 79 90 107 176 194 212 218
Temporal Medium 132 144 69 80 97 157 182 201 210
Temporal Low 132 143 66 77 93 154 179 198 207
Non-Temporal High 141 152 91 100 116 176 201 221 229
Non-Temporal Medium 133 145 75 85 102 163 187 207 216
Non-Temporal Low 131 144 68 79 96 156 182 201 210
FWR Input
Temporal High 136 155 88 97 112 168 190 210 218
Temporal Medium 129 152 78 88 103 160 184 202 206
Temporal Low 129 151 76 86 101 160 184 194 201
Non-Temporal High 142 161 103 112 126 181 203 221 229
Non-Temporal Medium 134 155 85 95 110 166 189 208 216
Non-Temporal Low 132 154 80 90 105 161 184 202 211
UL Max. Current Draw (mA RMS), 2-Wire Horn Strobe, High Candela Range (135–185 cd) DC Input
16–33 Volts
FWR Input
16–33 Volts
135 150 177 185 135 150 177 185
Temporal High 245 259 290 297 Temporal High 215 231 258 265 Temporal Medium 235 253 288 297 Temporal Medium 209 224 250 258 Temporal Low 232 251 282 292 Temporal Low 207 221 248 256 Non-Temporal High 255 270 303 309 Non-Temporal High 233 248 275 281 Non-Temporal Medium 242 259 293 299 Non-Temporal Medium 219 232 262 267 Non-Temporal Low 238 254 291 295 Non-Temporal Low 214 229 256 262 UL Current Draw Data
Horn Strobe Tones and Sound Output Data
3825 Ohio Avenue • St. Charles, IL 60174
Phone: 800-SENSOR2 • Fax: 630-377-6495
©2015 System Sensor.

Product specifications subject to change without notice. Visit systemsensor.com for current product information, including the latest version of this data sheet.

AVDS10102 • 03/15
SpectrAlert Advance Dimensions
Model Description
Ceiling Horn Strobes
PC2R 2-Wire Horn Strobe, Standard cd, Red
PC2R-P 2-Wire Horn Strobe, Standard cd, Red, Plain
(no “FIRE”) marking
PC2RH 2-Wire Horn Strobe, High cd, Red
PC2W 2-Wire Horn Strobe, Standard cd, White
PC2W-P 2-Wire Horn Strobe, Standard cd, White, Plain
(no “FIRE”) marking
PC2W-SP 2-Wire Horn Strobe, Standard cd, White, “Fuego” marking
PC2WH 2-Wire Horn Strobe, High cd, White
PC2WH-P 2-Wire Horn Strobe, High cd, White, Plain
(no “FIRE”) marking
PC2WH-SP 2-Wire Horn Strobe, High cd, White, “Fuego”
PC4R 4-Wire Horn Strobe, Standard cd, Red
PC4RH 4-Wire Horn Strobe, High cd, Red
PC4W 4-Wire Horn Strobe, Standard cd, White
SpectrAlert Advance Ordering Information
Notes:

All -P models have a plain housing (no “FIRE” marking on cover) All -SP models have “FUEGO” marking on cover
“Standard cd” refers to str
obes that include 15, 15/75, 30, 75, 95, 110, and 115 candela settings. “High cd” refers to strobes that include 135, 150, 177, and 185 candela settings.

4.7"

5.6"

6.8"
Dia.

2.5"

5.703"

1.85"

4.8"

6.922"
dia.

2.5"
Ceiling-mount horn strobes Ceiling back box surface mount back box Model Description
Ceiling Strobes
SCR Strobe, Standard cd, Red
SCRH Strobe, High cd, Red
SCW Strobe, Standard cd, White
SCW-P Strobe, Standard cd, White, Plain (no “Fire”) marking SCWH Strobe, High cd, White
Accessories
SBBCR Surface Mount Back Box, Ceiling, Red
SBBCW Surface Mount Back Box, Ceiling, White

LISTING No.: 7125-1653:0186
CATEGORY: 7125 - FIRE ALARM DEVICES FOR THE HEARING IMPAIRED LISTEE: System Sensor, Unincorporated Div of Honeywell Int'l Inc. 3825 Ohio Ave, St. Charles, IL, 60174
Contact: Brant,Lisa (203) 484-6105 (203) 484-7309
Email: [email protected]
DESIGN:

Synchronous type strobe lights, Models SR, SRH, SW, SW-CLR-ALERT, SWH, SCR, SCRH, SCW, SCW-CLR-ALERT and SCWH followed by the suffix -P, -SP, -PG, or none.

Intended for indoor use mounted on the wall or the ceiling. Refer to listee's data sheet for additional detailed product description and operational considerations.

RATING:
8-17.5 or 16-33 VDC/FWR
Candela: 15, 15/75, 30, 75, 95, 110, 115, *135, *150, *177, *185cd INSTALLATION:

In accordance with listee's printed installation instructions, applicable codes and ordinances, and in a manner acceptable to the authority having jurisdiction.

MARKING:

Listee's name, model number, electrical rating and UL label.

APPROVAL:

Listed as strobe lights suitable for hearing impaired application when used with separately listed compatible fire alarm control units. Suitable for indoor use, wall or ceiling mounted. Refer to listee’s Installation Instruction Manual for details.

NOTES:

Date Issued: 05/03/2024 Listing Expires: 06/30/2025
*Rev. 03-11-10 fm

Page 1 of 2 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE
Authorized By: David Castillo, Program Coordinator
Fire Engineering & Investigations Division

Page 2 of 2 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE
Agency Listings
Indoor Selectable-
Output Speaker
Strobes and Dual
Voltage Evacuation
Speakers for Wall
Applications
The SpectrAlert® Advance selectable output speaker
strobes and dual-voltage evacuation speakers can reduce ground faults and enable faster installation.

Features
• Plug-in design and protective cover reduce ground faults • Universal mounting plate with an onboard shorting spring tests wiring continuity before installation
• No extension ring required
• Field selectable candela settings:

Standard: 15, 15/75, 30, 75, 95, 110, 115
High: 135, 150, 177, 185
• Automatic selection of 12- or 24-volt operation at 15 and 15/75 candela
• Rotary switch simplifies field selection of speaker voltage (25 and 70.7 Vrms) and power settings (¼, ½, 1 and 2 watts) • SP speakers offer high fidelity sound output
• SPV speakers offer high volume sound output
• Compatible with System Sensor synchronization protocol • Electrical compatibility with existing SpectrAlert products • Tamper-resistant construction
• Listed for ceiling or wall mounting
The SpectrAlert Advance Series of speakers and speaker
strobes reduce costly ground faults using a plug-in design and universal mounting plate that allow the installer to pre-wire mounting plates, dress the wires, and confirm wiring continuity before plugging in the speakers. In addition, a protective plastic cover prevents nicked wires by covering exposed speaker components.

These devices also enable faster installations by providing instant feedback to ensure that wiring is properly connected, rotary switches to select voltage and power settings, and 11 field-selectable candela settings for both wall and ceiling speaker strobes.

The low total harmonic distortion of the SP speaker offers high fidelity sound output while the SPV speaker offers high volume sound output for use in high ambient noise applications.

SpectrAlert Advance makes installation easy
• Attach a universal mounting plate to a 4 × 4 × 21⁄8 inch back box .

Flush-mount applications do not require an extension ring. • Connect the notification appliance circuit or speaker wiring to the terminals on the mounting plate.
• Attach the speaker or speaker strobe to the mounting plate by inserting the product tabs into the mounting plate grooves. Hinge the device into position to lock the product pins into the mounting plate terminals. The device will temporarily hold in place with a catch until it is secured with a captured mounting screw. 10-08-E7320-1653:201S4048

SpectrAlert Advance Speaker and Speaker Strobe Specifications Architectural/Engineering Specifications
General
SpectrAlert Advance speaker and speaker strobes shall mount to a 4 × 4 × 21⁄8-inch back box. A universal mounting plate shall be used for mounting ceiling and wall products. The notification appliance circuit and amplifier wiring shall terminate at the universal mounting plate. Also, SpectrAlert Advance speaker strobes, when used with the Sync•Circuit™ Module accessory, shall be powered from a non-coded notification appliance circuit output and shall operate on a nominal 12 or 24 volts. When used with the Sync•Circuit Module, 12-volt rated notification appliance circuit outputs shall operate between 8.5 and 17.5 volts; 24-volt rated notification appliance circuit outputs shall operate between

16.5 and 33 volts. Indoor SpectrAlert Advance products shall operate between 32°F and 120°F from a regulated DC, or full-wave rectified, unfiltered power supply. Speaker strobes shall have field-selectable candela settings including 15, 15/75, 30, 75, 95, 110, 115, 135, 150, 177, 185.

Speaker
The speaker shall be a System Sensor SpectrAlert Advance model _______ dual-voltage transformer speaker capable of operating at 25.0 or

70.7 nominal Vrms. It should be listed to UL 1480 and shall be approved for fire protective service. The speaker shall have a frequency range of 400 to 4,000 Hz and shall have an operating temperature between 32°F and 120°F. The speaker shall have power taps and voltage that are selected by rotary switches.

Speaker Strobe combination
The speaker strobe shall be a System Sensor SpectrAlert Advance model __________ listed to UL1480 and UL 1971 and be approved for fire protective signaling systems. The speaker shall be capable of operating at 25.0 or 70.7 nominal Vrms selected via rotary switch, and shall have a frequency range of 400 to 4,000 Hz. The speaker shall have power taps that are selected by rotary switch. The strobe shall comply with the NFPA 72 requirements for visible signaling appliances, flashing at 1 Hz over the strobe’s entire operating voltage range. The strobe light shall consist of a xenon flash tube and associated lens/reflector system.

Synchronization Module
The module shall be a System Sensor Sync•Circuit model MDL3 listed to UL 464 and shall be approved for fire protective service. The module shall synchronize SpectrAlert strobes at 1 Hz. The module shall mount to a 411⁄16 × 411⁄16 × 21⁄8-inch back box. The module shall also control two Style Y (class B) circuits or one Style Z (class A) circuit. The module shall synchronize multiple zones. Daisy chaining two or more synchronization modules together will synchronize all the zones they control. The module shall not operate on a coded power supply.

Physical Specifications
Operating Temperature 32°F to 120°F (0°C to
49°C)
Humidity Range 10 to 93% non-
condensing
Dimensions, Wall-Mount Length Width Depth
SP Speaker 6 in, 152 mm 5 in, 127 mm 2.8 in, 71 mm
SPV Speaker 6 in, 152 mm 5 in, 127 mm 2.9 in, 74 mm
With Surface Mount Back Box 6 in, 152 mm 5.1 in, 130 mm 3.4 in, 86 mm SPS Speaker/Strobe
(including lens and speaker)
6 in, 152 mm 5.1 in, 127 mm 4.7 in, 119 mm
With Surface Mount Back Box 6 in, 152 mm 5.1 in, 130 mm 5.325 in, 135 mm Electrical/Operating Specifications
Nominal Voltage (speakers) 25 Volts or 70.7 Volts
(nominal)
Maximum Supervisory Voltage (speakers) 50 VDC
Strobe Flash Rate 1 flash per second
Nominal Voltage (strobes) Regulated 12 VDC/
FWR or regulated 24
DC/FWR
Operating Voltage Range (includes fire
alarm panels with built in sync)
8 to 17.5 V (12 V
nominal) or 16 to 33V
(24 V nominal)
Operating Voltage with MDL3 Sync Module 8.5 to 17.5 V (12 V nominal) or 16.5 to
33V (24 V nominal)
Frequency Range 400 to 4000 Hz
Power ¼, ½, 1, 2 watts
UL Current Draw Data
UL Max. Strobe Current Draw (mA RMS)
Candela
8 to 17 .5 Volts 16 to 33 Volts

DC FWR DC FWR
Standard
Candela Range
15 123 128 66 71
15/75 142 148 77 81
30 NA NA 94 96
75 NA NA 158 153
95 NA NA 181 176
110 NA NA 202 195
115 NA NA 210 205
High
Candela Range
135 NA NA 228 207
150 NA NA 246 220
177 NA NA 281 251
185 NA NA 286 258
Sound Output
UL Reverberant (dBA @ 10 ft.) 2W 1W ½ W ¼ W
Wall-Mount SP Series 86 83 80 77
Wall-Mount SPV Series 90 87 84 81
Wall-Mount SPS Series 85 82 79 76
Wall-Mount SPSV Series 89 86 83 80
Dimensions

5.00˝ .97˝ 1.84˝

5.98˝

5.00˝ 2.83˝

1.84˝1.60˝

5.97˝
Wall-Mount SP Speaker Wall-Mount SPS Speaker Strobe
3825 Ohio Avenue • St. Charles, IL 60174
Phone: 800-SENSOR2 • Fax: 630-377-6495
www.systemsensor.com
©2015 System Sensor.

Product specifications subject to change without notice. Visit systemsensor.com for current product information, including the latest version of this data sheet.

AVDS11602 • 2/15
Ordering Information for SpectrAlert® Advance Speakers and Speaker Strobes Wall Mount
White Red Description
SPW SPR Speaker only
SPWV SPRV Speaker only, High dB
SPSW SPSR Speaker Strobe, Standard cd
SPSW-P SPSR-P Plain Speaker Strobe, Standard cd
SPSW-ALERT — Speaker Strobe, Standard cd, Amber Lens
SPSW-CLR-ALERT — Speaker Strobe, Standard cd, Clear Lens SPSWH SPSRH Speaker Strobe, High cd
SPSWH-P — Plain Speaker Strobe, High cd
SPSWV SPSRV Speaker Strobe, Standard cd, High dB
SPSWV-P SPSRV-P Plain Speaker Strobe, Standard cd, High dB Accessories
White Red Description
RFPW RFP 7 in × 9.5 in Retrofit Plate
SBBSPW SBBSPR Surface Mount Back Box for Speakers and Speaker Strobes TRW TR Wall Mount Trim Ring
Notes:

All -P models have a plain housing (no “FIRE” marking on the cover) “Standard cd” refers to strobes that include 15, 15/75, 30, 75, 95, 110, and 115 candela settings. “High cd” refers to strobes that include 135, 150, 177, and 185 candela settings.

Surface Mounting
Wall-Mount Speaker Strobe with SBBSPR Surface Mount Back LISTING No.: 7320-1653:0201
CATEGORY: 7320 - SPEAKERS
LISTEE: System Sensor, Unincorporated Div of Honeywell Int'l Inc. 3825 Ohio Ave, St. Charles, IL, 60174
Contact: Brant, Lisa 2034846105
Email: [email protected]
DESIGN:

Models SPR,SPW,SPRV, and SPWV SpectrAlert Speakers - Rectangular enclosure.

Models SPCW, SPCR, SPCWV, and SPCRV SpectrAlert Speakers with round enclosure.

Models SPSR, SPSRH, SPSW, SPSW-ALERT, SPSW-CLR-ALERT, *SPSWK-CLR- ALERT, SPSWH, SPSRV, and SPSWV SpectrAlert Speaker/Strobe with rectangular enclosure. Models SPSCR, SPSCRH, SPSCW, *SPSCWK-CLR-ALERT, SPSCWH, SPSCRV, SPSCRVH, SPSCWV, and SPSCWVH SpectrAlert Speaker/Strobe with round enclosure. Model SPSCW-CLR-ALERT Speaker/Strobe. Model SPSW-ALERT has amber lens and is intended for non-fire use.

All models identified are intended for indoor use mounted on the wall or ceiling. Models with a “K” in the suffix are suitable for indoor or outdoor use with an operating temperature rating of -40°C to +66°C (-40°F to +151°F) and have a NEMA 4X enclosure rating when used with models PWBB, PWBBW (wall) or the model PWBBCW (ceiling) plastic weatherproof back boxes or with Model MWBBW (Wall), MWBB (Wall) or MWBBCW (Ceiling) metal weatherproof back boxes. Models with a “- P” in the suffix have plain housings with no lettering on the enclosure. Models not containing “- P”, in the suffix have English lettering reading “FIRE” on the housing. Refer to listee's data sheet for additional detailed product description and operational considerations.

RATING:

Nominal Voltage: 25 Vrms or 70 Vrms
Power Settings: ¼, ½, 1, 2 Watts
Frequency Range: 400 - 4000 Hz
INSTALLATION:

In accordance with listee's printed installation instructions, NFPA 72, applicable codes & ordinances and in a manner acceptable to the authority having jurisdiction.

MARKING:

Listee's name, model number, electrical rating and UL label.

Page 1 of 2 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE
APPROVAL:

Listed as speaker/strobes when used with separately listed compatible fire alarm control units. Suitable for wall or ceiling mount.

These speaker/strobes do not generate a distinctive three-pulse temporal code pattern (for total evacuation) as required per NFPA 72, 2010 edition. If required, the appliances must be used with a fire alarm control unit that can generate the temporal pattern signal.

NOTES:

Date Issued: 04/29/2024 Listing Expires: 06/30/2025
Authorized By: Michael Huang, Program Coordinator
Fire Engineering & Investigations Division
*Corrected 02-06-
12 bh

Page 2 of 2 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE
Agency Listings
Indoor Selectable-
Output Speaker
Strobes and Dual
Voltage Evacuation
Speakers for Ceiling
Applications
SpectrAlert® Advance selectable-output speaker strobes
and dual-voltage evacuation speakers can reduce ground
faults and enable faster installation.

The low total harmonic distortion of the SP speaker offers high fidelity sound output while the SPV speaker offers high volume sound output for use in high ambient noise applications.

SpectrAlert Advance makes installation easy
• Attach a universal mounting plate to a 4 × 4 × 21⁄8 inch back box .

Speaker
The speaker shall be a System Sensor SpectrAlert Advance model _______ dual-voltage transformer speaker capable of operating at 25.0 or

Synchronization Module
The module shall be a System Sensor Sync•Circuit model MDL3 listed to UL 464 and shall be approved for fire protective service. The module shall synchronize SpectrAlert strobes at 1 Hz. The module shall mount to a 411⁄16 × 411⁄16 × 21⁄8-inch back box. The module shall also control two Style Y (class B) circuits or one Style Z (class A) circuit. The module shall synchronize multiple zones. Daisy chaining two or more synchronization modules together will synchronize all the zones they control. The module shall not operate on a coded power supply.

Physical Specifications
Operating Temperature 32°F to 120°F (0°C to 49°C)
Humidity Range 10 to 93% non-condensing
Dimensions, Ceiling-Mount
Diameter Depth
SPC Speaker 6.8 in, 173 mm 2.8 in, 71 mm
SPCV Speaker 6.8 in, 173 mm 2.9 in, 74 mm
With Surface Mount Back Box 6.9 in, 175 mm 3.4 in, 86 mm SPSC Speaker Strobe 6.8 in, 173 mm 2.8 in, 71 mm
SPSCV Speaker Strobe 6.8 in, 173 mm 2.9 in, 74 mm
With Surface Mount Back Box 6.9 in, 175 mm 5.325 in, 135 mm Electrical/Operating Specifications
Nominal Voltage (speakers) 25 Volts or 70.7 Volts
(nominal)
Maximum Supervisory Voltage (speakers) 50 VDC
Strobe Flash Rate 1 flash per second
Nominal Voltage (strobes) Regulated 12 V DC/FWR or regulated 24 DC/FWR Operating Voltage Range (includes fire
alarm panels with built in sync)
8 to 17.5 V (12 V nominal) or 16 to 33 V (24 V nominal) Operating Voltage with MDL3 Sync Module 8.5 to 17.5 V (12 V nominal) or 16.5 to 33 V (24 V nominal) Frequency Range 400 to 4,000 Hz
Power ¼, ½, 1, 2 watts
UL Current Draw Data
UL Max. Strobe Current Draw (mA RMS)
Candela
8 to 17 .5 Volts 16 to 33 Volts

DC FWR DC FWR
Standard
Candela Range
15 123 128 66 71
15/75 142 148 77 81
30 NA NA 94 96
75 NA NA 158 153
95 NA NA 181 176
110 NA NA 202 195
115 NA NA 210 205
High
Candela Range
135 NA NA 228 207
150 NA NA 246 220
177 NA NA 281 251
185 NA NA 286 258
Sound Output
UL Reverberant (dBA @ 10 ft.) 2W 1W ½ W ¼ W
Ceiling-Mount SPC Series 86 83 80 77
Ceiling-Mount SPCV Series 90 87 84 81
Ceiling-Mount SPSC Series 85 82 79 76
Ceiling-Mount SPSCV Series 89 86 83 80
Dimensions

6.81˝ .97˝ 1.96˝ 6.81˝ .97˝ 1.84˝

6.81˝ 1.60˝ 1.84˝

2.83˝
Ceiling-Mount SPV Speaker Ceiling-Mount SP Speaker
Ceiling-Mount SPS Speaker Strobe
3825 Ohio Avenue • St. Charles, IL 60174
Phone: 800-SENSOR2 • Fax: 630-377-6495
www.systemsensor.com
©2015 System Sensor.

Product specifications subject to change without notice. Visit systemsensor.com for current product information, including the latest version of this data sheet.

AVDS11102 • 2/15
Ordering Information for SpectrAlert® Advance Speakers and Speaker Strobes Ceiling Mount
White Red Description
SPCW SPCR Speaker only
SPCWV SPCRV Speaker only, High dB
SPSCW SPSCR Speaker Strobe, Standard cd
SPSCW-P — Plain Speaker Strobe, Standard cd
SPSCWH SPSCRH Speaker Strobe, High cd
SPSCWH-P — Plain Speaker Strobe, High cd
SPSCWV SPSCRV Speaker Strobe, Standard cd, High dB
SPSCWV-P — Plain Speaker Strobe, High Volume, Clear Lens, White SPSCWVH SPSCRVH Speaker Strobe, High cd, High dB
SPSCW-CLR-ALERT — Speaker Strobe, Standard cd, Clear Lens Accessories
White Red Description
RFPW RFP 7 in × 9.5 in Retrofit Plate
SBBCW SBBCR Surface Mount Back Box
TRCW TRC Ceiling Mount Trim Ring
Notes:

All -P models have a plain housing (no “FIRE” marking on cover) “Standard cd” refers to strobes that include 15, 15/75, 30, 75, 95, 110, and 115 candela settings. “High cd” refers to strobes that include 135, 150, 177, and 185 candela settings.

Surface Mounting
Ceiling-Mount Speaker with SBBCR/SBBCW Surface Mount Back Box Skirt LISTING No.: 7320-1653:0201
CATEGORY: 7320 - SPEAKERS
LISTEE: System Sensor, Unincorporated Div of Honeywell Int'l Inc. 3825 Ohio Ave, St. Charles, IL, 60174
Contact: Brant, Lisa 2034846105
Email: [email protected]
DESIGN:

Models SPR,SPW,SPRV, and SPWV SpectrAlert Speakers - Rectangular enclosure.

Models SPCW, SPCR, SPCWV, and SPCRV SpectrAlert Speakers with round enclosure.

RATING:

Nominal Voltage: 25 Vrms or 70 Vrms
Power Settings: ¼, ½, 1, 2 Watts
Frequency Range: 400 - 4000 Hz
INSTALLATION:

In accordance with listee's printed installation instructions, NFPA 72, applicable codes & ordinances and in a manner acceptable to the authority having jurisdiction.

MARKING:

Listee's name, model number, electrical rating and UL label.

Page 1 of 2 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE
APPROVAL:

Listed as speaker/strobes when used with separately listed compatible fire alarm control units. Suitable for wall or ceiling mount.

NOTES:

Date Issued: 04/29/2024 Listing Expires: 06/30/2025
Authorized By: Michael Huang, Program Coordinator
Fire Engineering & Investigations Division
*Corrected 02-06-
12 bh

Page 2 of 2 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE
Agency Listings
Outdoor, Selectable-
Output Speaker
Strobes and Dual-
Voltage Evacuation
Speakers for Wall
Applications
SpectrAlert® Advance outdoor, selectable-output speaker strobes and dual-voltage evacuation speakers meet
virtually any outdoor application requirement.

Features
• Weatherproof per NEMA 4X, IP56
• Rated from -40°F to 151°F
• Plug-in design reduces ground faults
• Universal mounting plate with onboard shorting spring that tests wiring continuity befor
e devices are installed
• Field-selectable candela settings: 15, 15/75, 30, 75, 95, 110, 115, 135, 150, 177, and 185
•
Automatic selection of 12- or 24-volt operation at 15 and 15/75 candela
• Rotary switch for speaker voltage (25 and 70.7 Vr
ms) and power
settings (1/4, 1/2, 1 and 2 watts)
• Compatible with System Sensor synchronization protocol and legacy SpectrAler
t products
• Tamper-r
esistant construction
• Listed for ceiling or wall mounting
SpectrAlert Advance of
fers the broadest line of outdoor
speakers and speaker strobes in the industry. From metal and plastic outdoor back boxes, to white and red plastic housings, to wall and ceiling mounting options, SpectrAlert Advance can meet virtually any application requirement.

Wall-mount outdoor speakers and speaker strobes can be used indoors or outdoors in wet or dry applications, and can provide reliable operation from −40°F to 151°F. These speakers provide a broad frequency response range, low harmonic distortion and maintain a high sound pressure level at all tap settings to provide accurate and intelligible broadcast of evacuation messages.

Like the entire SpectrAlert Advance line, wall-mount outdoor speakers and speaker strobes include a variety of features that increase application flexibility and simplify installation. First, field-selectable settings, including candela, speaker voltage and power settings, and automatic selection of 12- or 24-volt operation enable installers to easily adapt devices to meet requirements.

Next, these devices use a universal mounting plate with an onboard shorting spring that ensures wiring continuity before devices are installed, so installers can verify proper wiring without mounting the devices and exposing them to potential construction damage. Once the plates are mounted, all SpectrAlert Advance devices utilize a plug-in design with a single captured screw to speed installation and virtually eliminate costly ground faults.

Outdoor devices ship with weatherproof plastic back boxes (metal back boxes are available separately) that accommodate in-and- out wiring for daisy chaining devices. Plastic back boxes feature removable side flanges and improved resistance to saltwater corrosion. Knock-outs located on the back eliminate the need to drill holes for screw-in mounting. Plastic and metal weatherproof back boxes come with ¾-inch top and bottom conduit entries and ¾-inch knock-outs at the back. A screw-in NPT plug with an O-ring gasket for a watertight seal is included with each back box.
10-08-E7320-1653:20175S0
AVDS11301
SpectrAlert® Advance Outdoor Speaker and Speaker Strobe Specifications Architectural/Engineering Specifications
General
SpectrAlert Advance outdoor speakers and speaker strobes shall mount to a weatherproof back box. A universal mounting plate shall be used for mounting ceiling and wall products. The notification appliance circuit and amplifier wiring shall terminate at the universal mounting plate. Also, SpectrAlert Advance speaker strobes, when used with the Sync•Circuit ™ Module accessory, shall be powered from a non-coded
notification appliance circuit output and shall operate on a nominal 12 or 24 volts. When used with the Sync•Circuit Module, 12-volt-rated notification appliance circuit outputs shall operate between 8.5 and 17.5 volts; 24-volt-rated notification appliance circuit outputs shall operate between 16.5 and 33 volts. Outdoor SpectrAlert Advance products shall operate between –40°F and 151°F from a regulated DC, or full-wave rectified, unfiltered power supply.

Speaker
Speaker shall be a System Sensor SpectrAlert Advance Model ______ dual-voltage transformer speaker capable of operating at 25.0 or 70.7 nominal Vrms. Speaker shall be listed to Underwriters Laboratories Standard S4048 for outdoor fire protective signaling systems. Speaker shall have a frequency range of 400 to 4,000 Hz and shall have an operating temperature from –40°F to 150.8°F. Speaker shall have power taps and wattage settings that are selected by rotary switches. The speaker must be installed with its weatherproof back box in order to remain outdoor approved per UL listing S4048. The speaker shall be suitable for use in air handling spaces and wet environments.

Speaker Strobe Combination
The speaker strobe shall be a System Sensor Model _____ listed to UL 1638 and UL 1480 and be approved for fire protective signaling systems. Speaker shall be capable of operating at 25.0 or 70.7 nominal Vrms and shall have a frequency range of 400 to 4,000 Hz. Speaker shall have power taps that are selected by rotary switch. The strobe shall consist of a xenon flash tube with associated lens/reflector system and operate on either 12 or 24 volts. The strobe shall also feature selectable candela output, providing options for 15 or 15/75 candela when operating on 12 volts and 15, 15/75, 30, 75, 110, 115, 135, 150, 177 or 185 candela when operating on 24 volts. The strobe shall comply with the Americans with Disabilities Act requirement for visible signaling appliances, flashing at 1 Hz over the strobe’s entire operating voltage range. The speaker strobe must be installed with its weatherproof back box in order to remain outdoor approved per UL. The speaker strobe shall be suitable for use in wet environments.

Physical Specifications
Operating Temperature –40°F to 151°F (–40°C to 66°C)
Dimensions, Wall-Mount
SPS Speaker Strobe 6.0˝ L × 5.0˝ W × 4.7˝ D (including lens and speaker) SP Speaker 6.0˝ L × 5.0˝ W × 2.9˝ D
Dimensions, Wall-Mount Weatherproof Back Box 6.5˝ L × 5.5˝ H × 2.9˝ D Electrical/Operating Specifications
Nominal Voltage (speakers) 25 V or 70.7 V (nominal)
Maximum Supervisory Voltage (speakers) 50 VDC
Strobe Flash Rate 1 flash per second
Nominal Voltage (strobes) Regulated 12 VDC/FWR or regulated 24 DC/FWR Operating Voltage Range (includes fire alarm
panels with built in sync)
8 to 17.5 V (12 V nominal) or 16 to 33 V (24 V nominal) Operating Voltage with MDL3 Sync Module 8.5 to 17.5 V (12 V nominal) or 16.5 to 33 V (24 V nominal) Frequency Range 400 to 4,000 Hz
Power ¼, ½, 1, 2 watts
AVDS11301
UL Current Draw Data
UL Max. Strobe Current Draw (mA RMS)
Candela
8 to 17 .5 Volts 16 to 33 Volts

DC FWR DC FWR
Standard
Candela Range
15 123 128 66 71
15/75 142 148 77 81
30 NA NA 94 96
75 NA NA 158 153
95 NA NA 181 176
110 NA NA 202 195
115 NA NA 210 205
High
Candela Range
135 NA NA 228 207
150 NA NA 246 220
177 NA NA 281 251
185 NA NA 286 258
Sound Output
UL Reverberant (dBA @ 10 ft.) 2W 1W ½ W ¼ W
Outdoor Speaker 90 87 84 81
Outdoor Speaker/Strobe 89 86 83 80Dimensions
Candela Derating
For K series products used at low
temperatures, listed candela ratings must be
reduced in accordance with this table.

Strobe Output (cd)
Listed Candela Candela rating at
–40°F
15 Do not use below 32°F15/75
30 75 44
95 70
110 110
115 115
135 135
150 150
177 177
185 185

5.00˝ .97˝ 1.84˝

5.98˝

5.00˝ 2.83˝

1.84˝1.60˝

5.97˝
Wall-Mount Outdoor Speaker Wall-Mount Outdoor Speaker Strobe 3825 Ohio Avenue • St. Charles, IL 60174
Phone: 800-SENSOR2 • Fax: 630-377-6495
©2012 System Sensor.

Product specifications subject to change without notice. Visit systemsensor.com for current product information, including the latest version of this data sheet.

AVDS11301 • 09/12
Ordering Information for SpectrAlert® Advance Outdoor Speakers and Speaker Strobes Wall Mount
White Red Description
SPWK SPRK Outdoor Speaker (includes plastic weatherproof back box) SPWK-R SPRK-R Outdoor Speaker (does not include plastic weatherproof back box) SPSWK SPSRK Outdoor Speaker Strobe, Standard cd (includes plastic weatherproof back box) SPSWK-P SPSRK-P Plain Outdoor Speaker Strobe, Standard cd(includes plastic weatherproof back box) SPSWK-R SPSRK-R Outdoor Speaker Strobe, Standard cd(does not include weatherproof back box) SPSWK-CLR-ALERT — Outdoor Speaker Strobe, Standard cd, Clear Lens, ALERT Printed (includes plastic weatherproof back box)
— SPSRHK Outdoor Speaker Strobe, High cd (135,150,177,185) (includes plastic weatherproof back box) Accessories
White Red Description
MWBBW MWBB Wall, Metal Weatherproof Back Box
Notes:

Surface Mounting
Wall-Mount Speaker Strobe with Plastic Weatherproof Back Box Wall-Mount Speaker Strobe with Metal Weatherproof Back Box Wall-Mount Speaker with Plastic Weatherproof Back Box
Wall-Mount Speaker with Metal Weatherproof Back Box
LISTING No.: 7320-1653:0201
CATEGORY: 7320 - SPEAKERS
LISTEE: System Sensor, Unincorporated Div of Honeywell Int'l Inc. 3825 Ohio Ave, St. Charles, IL, 60174
Contact: Brant, Lisa 2034846105
Email: [email protected]
DESIGN:

Models SPR,SPW,SPRV, and SPWV SpectrAlert Speakers - Rectangular enclosure.

Models SPCW, SPCR, SPCWV, and SPCRV SpectrAlert Speakers with round enclosure.

RATING:

Nominal Voltage: 25 Vrms or 70 Vrms
Power Settings: ¼, ½, 1, 2 Watts
Frequency Range: 400 - 4000 Hz
INSTALLATION:

In accordance with listee's printed installation instructions, NFPA 72, applicable codes & ordinances and in a manner acceptable to the authority having jurisdiction.

MARKING:

Listee's name, model number, electrical rating and UL label.

Page 1 of 2 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE
APPROVAL:

Listed as speaker/strobes when used with separately listed compatible fire alarm control units. Suitable for wall or ceiling mount.

NOTES:

Date Issued: 04/29/2024 Listing Expires: 06/30/2025
Authorized By: Michael Huang, Program Coordinator
Fire Engineering & Investigations Division
*Corrected 02-06-
12 bh

Page 2 of 2 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE

FEATURES & BENEFITS
• Installer can open
st
ation without
causing an alarm
condition
•
Dua
l-color LED is
visible through handle
of station blinks green
to indicate normal
operation and remains
steady red in an alarm
condition
•
Key o perated test and
reset lock using lock
plate actuator
•
Key m
atches
compatible FACP
locks
•
Mee
ts ADA
requirement for 5 lbs
maximum pull force to
active
•
Mee ts the Americans
with Disabilities Act
Accessibility
Guidelines (ADAAG)
controls and operating
mechanisms
guidelines (Section

4.1.3[13])
•
She
ll, door, and handle
molded from durable
LEXAN
®
• Reliable analog
co
mmunications for
trouble-free operation
• Bra
ille text on station
handle
• Rot
ary address
switches for fast
installation
•
Han dle latches in
down position and the
word Activated
appears, clearly
indicating the station
has been pulled
•
UL Li
sted, including
UL 38, Standard of
Manually Actuated
Signaling System
•
CSF
M Listed
• MEA L
isted

SK-PULL-SA / SK-PULL-DA
Intelligent Pull Stations
The SK-PULL -SA is a single action pull station requiring only one motion to activate the station. The SK-PULL -DA is a dual action pull station requiring two motions to active the station. The SK-PULL -SA and SK-PULL -DA are for use with Honeywell Silent Knight Series fire control panel (FACP).

Extremely easy to operate, the SK-PULL -DA and SK-PULL -SA provide a fast and practical means of manually initiating a fire alarm signal. The FACP recognizes each manual pull station by its specific address saving precious seconds in determining the location of an alarm.

INSTALLATION
The SK-PULL -SA and SK-PULL -DA can be surface mounted to an SB-I/O surface back box or semi-flush mounted on a standard single-gang with a minimum depth of 2.13”(5.40 cm) or double gang or 4” (10.61 cm) square electrical box. You can also use the optional (System Sensor® PN BG-TR) trim ring if the station is being semi-flush mounted.

SK-PULL-SA

SK-PULL-DA
For a complete listing of all
compliance approvals and
certifications, please visit
www.silentknight.com .

Microsoft, Windows, and
the Windows Logo are
registered trademarks
or trademarks of
Microsoft Corporation.

Silent Knight®, System
Sensor® and Honeywell®
are registered
trademarks of Honeywell
International, Inc.

For Technical Support,
call 800-446-6444.

SK-PULL -SA / SK-PULL -DA Technical Specifications

PHYSICAL
Dimensions: 5.5” H x 4" W x 1.45" D (14 x 10.2 x
3 .7cm)
Housing Material: LEXAN polycarbonate resin
Bi-Colored LED:

Blinking Green: Normal
Steady Red: Alarm
Switch: Single pole, single throw (SPST) normally
open (N/O) switch which closes upon activation of
the pull station

ELECTRICAL
Operating Voltage: 15 – 32VDC
SLC Standby and Alarm Current: 350μA
Wire Gauge: Up to 12AWG (3.1 mm2)

ENVIRONMENTAL
Operating Temperature: 32ºF – 120ºF (0ºC –
49ºC)
Humidity: 10% – 93% non-condensing

ORDERING INFORMATION
SK-Pull-SA: Single Action Pull Station
SK-Pull-DA: Dual Action Pull Station

ACCESSORIES
BG-TR: Optional trim ring.

SB-I/O: Surface backbox, indoor/outdoor.
* Unless otherwise noted, specifications apply to
SK-Pull-SA and SK-Pull-DA

COMPATIBILITY
The SK-PULL-SA AND SK-PULL-DA are
compatible with the following Honeywell Silent
Knight fire alarm control panels:
6820: Addressable fire alarm control panel
6820EVS: Addressable fire alarm control panel
with an emergency voice system.
6808: Addressable fire alarm control panel
6700: Addressable fire alarm control panel
5700: Addressable fire alarm control panel
5808: Addressable fire alarm control panel
5820XL: Addressable fire alarm control panel
5820XL-EVS: Addressable fire alarm control panel
with an emergency voice system
Doc 350135 | Rev E | 11/17
© 2017 Honeywell International Inc.

For more information
Learn more about Honeywell Silent Knight and other
products by visiting www.silentknight.com
Honeywell Silent Knight
12 Clintonville Road
Northford, CT 06472
800-328-0103
LISTING No.: 7150-0559:0161
PARENT LISTING No.: 7150-0028:0199
CATEGORY: 7150 - FIRE ALARM PULL BOXES
LISTEE: SILENT KNIGHT SECURITY One Fire-Lite Place, Northford, CT, 06472 Contact: Brant, Lisa 2034846105
Email: [email protected]
DESIGN:

Models SK-PULL-SA and SK-PULL-DA single/dual action fire alarm pull boxes. Refer to listee's data sheet for detailed product description and operational considerations.

RATING:

INSTALLATION:

In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction.

MARKING:

Listee's name, model number, rating, and UL label.

APPROVAL:

Listed as fire alarm pull boxes for use with separately listed compatible fire alarm control units. Refer to listee’s Installation Instruction Manual for details.

* These manual pull boxes meet the requirements of UL Standard 38, 1999 Edition with California amendments.

NOTES:

This listing is based upon technical data submitted by the applicant. OSFM Fire Engineering staff has reviewed the test resultsand/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria.Refer to listee's data sheet, installation instructions and/or other suitable information sources.

Date Issued: 05/08/2024 Listing Expires: 06/30/2025
04-16-09

Page 1 of 2 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE
Authorized By: David Castillo , Program Coordinator
Fire Engineering & Investigations Division

Page 2 of 2 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE

FEATURES & BENEFITS
• Single contact monitor
• Sup
port for Class A
and Class B wiring
• Ful
ly supervised
• Pan el controlled
status LED that
flashes green in
normal state and is
solid red in alarm
•
SEM
S screws for easy
wiring
• UL Li sted
• Rot
ary address
switches for fast
installation

SK-MONITOR
Intelligent Monitor Module
The SK-MONITOR is an addressable monitor module for use with Honeywell Silent Knight Series fire alarm control panels (FACPs). The SK-MONITOR is intended for use in intelligent, two-wire systems, where individual address of each module is selected using the built-in rotary switches.

The SK-MONITOR supports Class A supervised or Class B supervised wiring to the load device. Conventional 4-wire smoke detectors can be monitored for alarm and trouble conditions.

INSTALLATION
The SK-MONITOR mounts directly into a 4” square electrical box. The box must have a minimum depth of 2-1/8”. A surface mount electrical box (System Sensor® PN SMB500) is available from Silent Knight. SK-MONITOR For a complete listing of all
compliance approvals and
certifications, please visit
www.silentknight.com .

Microsoft, Windows, and
the Windows Logo are
registered trademarks
or trademarks of
Microsoft Corporation.

Silent Knight®, System
Sensor® and Honeywell®
are registered
trademarks of Honeywell
International, Inc.

For Technical Support,
call 800-446-6444.

SK-MONITOR Technical Specifications

PHYSICAL
Height: 4.5”H x 4” W x 1.25”D (11.4 X 10.2 X 3cm)
Shipping Weight: 6.3 oz (196 g)

ELECTRICAL
Operating Voltage: 15 – 32VDC
Current Draw (LED on): 5.0mA max
Operating Current (LED flashing): 375μA
Standby Current: 400 μ A max @ 24 VDC (one
communication every 5 sec with 47K EOL); 550 μA
max @ 24 VDC (one communication every 5 sec
with EOL <1K)

5.5 mA (with LED latched on)
LED Current: 5.5 mA (with LED latched on)
End-of-Line Resistance: 47K W
Initiating Device Circuit Wiring Resistance: 1,500
W max
SLC Loop Resistance: 40 W max.

ENVIRONMENTAL
Operating Temperature: 32ºF – 120ºF (0ºC –
49ºC)
Humidity: 10% – 93% non-condensing

ORDERING INFORMATION
SK-MONITOR: Monitor Module
ACCESSORIES .

SMB500: 4” Square surface mount electrical box

COMPATIBILITY
The SK-MONITOR is compatible with the
following Honeywell Silent Knight fire alarm
control panels:
6820: Addressable fire alarm control panel
6820EVS: Addressable fire alarm control panel
with an emergency mass notification system.
6808: Addressable fire alarm control panel
6700: Addressable fire alarm control panel
5700: Addressable fire alarm control panel
5808: Addressable fire alarm control panel
5820XL: Addressable fire alarm control panel
5820XL-EVS: Addressable fire alarm control panel
with an emergency mass notification system
Doc 350131 | Rev G | 11/17
© 2017 Honeywell International Inc.

For more information
Learn more about Honeywell Silent Knight and other
products by visiting
www.silentknight.com
Honeywell Silent Knight
12 Clintonville Road
Northford, CT 06472
800-328-0103
LISTING No.: 7300-0559:0155
PARENT LISTING No.: 7300-0028:0219
CATEGORY: 7300 - FIRE ALARM CONTROL UNIT ACCESSORIES/MISC. DEVICES LISTEE: SILENT KNIGHT SECURITY One Fire-Lite Place, Northford, CT, 06472 Contact: Brant, Lisa 2034846105
Email: [email protected]
DESIGN:

Models IDP-Relay-6, SK-Relay-6, relay module, IDP-Control-6, SK -Control-6, supervising control module, IDP-Monitor-10, SK-Mon-10, input monitor module, IDP- Zone-6, SK-Zone-6 six zone interface module, IDP-Monitor, IDP-Minimon, IDP-Zone, SK-Monitor, SK-Minimon, SK-Zone monitor modules, IDP-Control, IDP-Relay, SK- Control, SK-Relay, control modules, IDP-Monitor-2, SK-Monitor-2, dual monitor modules,and *IDP-RELAYMON-2, *SK-RELAYMON-2 with 2 input/2 output relay modules. All devices are intended to be connected between the signaling line circuit of a compatible fire alarm control panel. Refer to listee's data sheet for additional detailed product description and operational considerations.

RATING:
16-33 VDC Primary
INSTALLATION:

In accordance with listee's printed installation instructions, applicable codes & ordinances and in manner acceptable to the authority having jurisdiction.

MARKING:

Listee's name, product number and UL label.

APPROVAL:

Listed as control unit accessories for use with listee's separately listed compatible fire alarm control units.

NOTES:

If an external power supply is used for Model SK-Zone-6 and IDP-Zone-6, the negative of the external power supply is referenced to the negative of the auxiliary supply of the compatible control panel. This is done in order to detect ground faults on the initiating circuit.
*Rev. 10-25-11 mt

Page 1 of 2 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE
This listing is based upon technical data submitted by the applicant. OSFM Fire Engineering staff has reviewed the test resultsand/or other data but does not make an independent verification of any claims. This listing is not an endorsement or recommendation of the item listed. This listing should not be used to verify correct operational requirements or installation criteria.Refer to listee's data sheet, installation instructions and/or other suitable information sources.

Date Issued: 05/08/2024 Listing Expires: 06/30/2025
Authorized By: David Castillo , Program Coordinator
Fire Engineering & Investigations Division

Page 2 of 2 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE
PCVS Series
Control Valve Supervisory Switch
5401526 - REV F • 8/15
PAGE 1 OF 7
Potter Electric Signal Company, LLC • St. Louis, MO • Tech Support: 866-956-0988 / Customer Service: 866-572-3005 • www.pottersignal.com Features
• NEMA 4X* (IP 65) and 6P (IP 67)
*Enclosure is 4X. For additional corrosion protection of mounting hardware, use model PCVS-2 CRH
• -40º to 140º (-40ºC to 60ºC) operating temperature range • Visual Switch Indicators
• Two conduit entrances
• Adjustable length trip rod
• Accomodates up to 12AWG wire
• Switch detects tampering and valve closure
• RoHS compliant
• Two SPDT contacts
Description
The Model PCVS is a weather proof and tamper resistant switch for monitoring the open position of fire sprinkler control valves of the wall and yard post indicator and butterfly types. Two SPDT (Form C) contacts are provided which will operate when the valve position is altered from an open state.

The unit mounts in a 1/2” NPT tapped hole in the post indicator or butterfly valve housing. The devic e is engage d by the indic ating assembly of the post indicator or the operating mechanism of the butterfly valve, actuating switches when the valve is fully open. The unit should be installed where it is accessible for service.

The cover is held in place by two tamper resistant screws that require a special tool to remove. The tool is furnished with each device.

Testing
The operation of the PCVS and its associated protective monitoring system shall be tested upon completion of the installation and in- spected, tested and maintained in accordance with all applicable local and national codes and standards and/or the Authority Having Juris- diction, (manufacturer recommends quarterly or more frequently). A minimum test shall consist of turning the valve operating mechanism towards the closed position. The PCVS shall operate within the first two revolutions of the operating mechanism. Fully close the valve and ensure the PCVS does not restore. Fully open the valve and ensure that the PCVS restores to normal.

Technical Specifications
Dimensions See Fig 10
Weight 1.0 lbs (0,45 kg)
Enclosure
Cover: Die Cast Finish: Red Powder Coat
Base: Die Cast Finish: Black Powder Coat
All parts have corrosion resistant finishes
Cover Tamper Tamper Resistant Screws
Optional Cover Tamper Switch Available
Contact
Ratings
PCVS-2: Two Sets of SPDT (Form C)

10.0 Amps at 125/250 V AC

2.0 Amps at 30VDC Resistive
10 mAmps minimum at 24 VDC
Environmental
Limitations
-40º F to 140ºF (-40ºC to 60ºC)
NEMA 4X (IP 65) and NEMA 6P Enclosure (IP67)
(Use suitably rated conduit and connector)
Indoor or Outdoor Use (See PIVSU-EX Bulletin
5400694 for Hazardous locations)
Conduit
Entrances
Two Knockouts for 1/2” conduit provided
(See Notice on Page 7 and Fig. 11 on Page 6)
Service Use NFPA 13, 13D, 13R, 72
Important: This document contains important information on the installation and operation of PCVS valve supervisory switches. Please read all instructions carefully before beginning installation. A copy of this document is required by NFPA 72 to be maintained on site.

Specifications subject to change without notice
Before any work is done on the fire sprinkler or fire alarm system, the building owner or their authorized representative shall be notified.

Before opening any closed valve, ensure that opening the valve will not cause any damage from water flow due to open or missing sprinklers, piping, etc.
5401526 - REV F • 8/15
PAGE 2 OF 7
Potter Electric Signal Company, LLC • St. Louis, MO • Tech Support: 866-956-0988 / Customer Service: 866-572-3005 • www.pottersignal.com PCVS Series
Control Valve Supervisory Switch
Hood Moves Down as Valve is Shut
Theory Of Operation
The PCVS is a spring loaded switch. It is in normal position when the trip rod is pulling against the spring force. Normal is when the switch is installed on the valve and the valve is fully open. As the valve closes, the valve actuator moves away from the trip rod of the PCVS and the spring on the PCVS pulls the trip rod over and trips the switch.

Alternate Window Installation and Moving Hood Installation If the target is stationary and a hood arrangement is used, such as is shown in Fig. 2, the hood must be drilled with a 23/32” drill and tapped with a 1/2” NPT. The center line of this hole should be 1/8” below the portion of target assembly that strikes the PCVS trip rod.

The 11 3/8” dimension shown is for a Clow V alve. Flexible conduit must be used for this type of installation. (More on pg. 3).

Target Assembly
Shut Marker
Steel Tripping Block
Replaces Open Marker Metal Plate Replaces Glass
Target Moves Up as Valve is Shut
Locknut
Fig 1 Fig 2
Locknut
11 3/8”
(28,9 cm)
Subject to the approval of the “authority having jurisdiction” the alternate method of installation shown in Fig. 1 may be used. In this method, one of the glass windows of the housing is replaced with a 1/4” thick metal plate that is cut to fit in place of the glass and drilled and tapped to recieve 1/2” NPT pipe nipple. In some cases it may be necessary to attach an angle bracket to the target assembly to engage the PCVS trip rod.
5401526 - REV F • 8/15
PAGE 3 OF 7
Potter Electric Signal Company, LLC • St. Louis, MO • Tech Support: 866-956-0988 / Customer Service: 866-572-3005 • www.pottersignal.com PCVS Series
Control Valve Supervisory Switch
NOTE: Before any work is done on the fire sprinkler or fire alarm system, the building owner or their authorized representative shall be notified. Before opening any closed valve, ensure that opening the valve will not cause any damage from water flow due to open or missing sprinklers, piping, etc.

1. Position the valve to fully open (“OPEN” should appear in the window of the housing). Partially close the valve while observing the direction that the target assembly moves.

Reopen the valve. If the valve housing is predrilled with a 1/2” NPT for installation of a monitoring switch, remove the 1/2” plug and fully open the valve. Make sure that “OPEN” appears in the window of the housing. GO TO STEP NO. 6.

2. If the valve is not pre-drilled for 1/2” NPT, remove the head and target assembly (consultation with valve manufacturer is recommended).

3. If the target assembly moved up as the valve was closed, measure the distance from the bottom of the head to the lower part of the target assembly that will contact the trip rod of the PCVS (see Fig. 3). This is usually a plate or bar on the target assembly, on a side adjacent to the “OPEN/SHUT”
plates. Subtract 1/8” from the measurement. If the target moved down as the valve was closed, measure the distance from the bottom of the head to the upper portion of the target assembly that will contact the trip rod of the PCVS (see Fig. 4). Add 1/8” (3,2mm) to this measurement.

4. Mark the housing at the proper location. Using a 23/32” (18,2mm) drill bit, drill and then tap a 1/2” NPT in the housing on the side that coincides with the portion of the target assembly that will engage the trip rod of the PCVS.

5. Replace the head and target assembly.

6. Loosen the socket head screw that holds the nipple in the PCVS and remove the nipple.

7. Screw the locknut that is provided onto the nipple.

8. Screw the nipple into the 1/2” NPT hole in the valve housing hand tighten. Tighten the locknut against the valve housing to secure the nipple firmly in place.

9. Insert a scale or probe thru the nipple to measure the distance from the open end of the nipple to the target assembly.

Subtract 1/2” (12,5mm) from this measurement.

NOTE: In some cases, it may be necessary to attach an
angle bracket to the target assembly to engage the PCVS trip rod.

10. Using the special tool provided, loosen the two cover screws and remove the cover from the PCVS.

11. Loosen the locking screw that holds the trip rod in place and adjust the rod length, from the end of the collar to the end of the rod, using the dimension determined in Step 9. Tighten the locking screw to 5 in-lbs minimum to hold the rod in place and properly seal the enclosure.

12. Partially close the valve to move the target assembly away (3 to 4 revolutions of the handle/hand wheel).

13. With the PCVS positioned so the spring will pull the trip rod to follow the target as the valve is closing, slide the PCVS over the nipple. Tighten the socket head screw in the collar.

14. Carefully open the valve to the fully open position. As the target moves to the open position it should engage the trip rod and actuate the switch(es). There should be a minimum overtravel of 1/2 revolution of the handle/hand wheel after the switch(es) actuate (a continuity meter connected to each set of contacts is one method that could be used to determine this).

15. Slowly close the valve. The switch must operate during the first two revolutions of the handle/hand wheel or during 1/5 of the travel distance of the valve control apparatus from its normal condition.

NOTE: Small adjustments of the target position may
be necessary (consultation with valve manufacturer is
recommended).

16. Complete the required electrical wiring, connections and tests. The valve should be operated through the entire cycle of fully closed and fully open to determine the integrity of the PCVS installation and the signaling system. Check that all electrical and mechanical connections are secure.

17. Reinstall the cover and tighten the cover screws to 15 in-lbs minimum to properly seal the enclosure.

18. When the installation and testing are complete, return valve to its proper position.

19. Alternative installation for other post indicator valve housing shown in Fig. 1 and 2.

Typical Installations On Post Indicator Valve Housings
Target moves up
as valve is shut.

Target moves down
as valve is shut.

Fig 3 Fig 4
5401526 - REV F • 8/15
PAGE 4 OF 7
Potter Electric Signal Company, LLC • St. Louis, MO • Tech Support: 866-956-0988 / Customer Service: 866-572-3005 • www.pottersignal.com PCVS Series
Control Valve Supervisory Switch
Dresser Indicating Butterfly V alveTypical Indicating Butterfly V alve

1. Remove the 1/2” NPT plug from the gear operator case.

2. Loosen the set screw that holds the nipple in the PCVS and remove the nipple.

3. Screw the locknut that is provided onto the nipple.

4. Screw the nipple into the 1/2” NPT hole in the gear operator-hand tighten. Tighten the locknut against the case, to secure the nipple firmly in place

5. Partially close the valve to move the boss on the gear hub out of the way (3 or 4 revolutions of the hand wheel or crank).

6. Using the special tool provided, loosen the two cover screws and remove the cover from the PCVS.

7. Orient the PCVS so the spring will pull up the trip rod to follow the actuating cam inside the valve.

NOTE: If trip rod length is excessive, loosen the locking screw and remove the trip rod from the trip lever. Using pliers, break off the one (1) inch long notched section (see Fig. 12). Reinstall the trip rod, tightening the screw to 5 in-lbs minimum, and repeat Step 7 procedure.

8. Remove device from nipple and shorten the trip rod 1/32” (0,80mm) (this is to prevent the trip rod from dragging on the gear hub inside the valve). Tighten the locking screw to hold the rod in place. Re-install the device on the nipple. Tighten the screw in the collar against the nipple.

NOTE: In some cases it may be necessary to remove the
gear box cover to ensure correct operation (consultation with the valve manufacturer is recommended).

9. Carefully open the valve to its full open position, as the boss on the gear hub moves to the open position it must engage the PCVS trip rod and actuate the switch(es). There should be a minimum overtravel or revolution of the crank or hand wheel after the switch(es) actuate (a continuity meter connected to each set of contacts is one method that could be used to determine this).

NOTE: Slight adjustment of gear stops may be necessary to prevent overtravel of the trip rod (consultation with valve manufacture is recommended).

10. Carefully close the valve. The switch(es) must operate during the first two revolutions of the crank or hand wheel or during 1/5 of the travel distance of the valve control apparatus from its normal condition.

11. Complete the required electrical wiring, connections and tests.

The valve should be operated through the entire cycle of fully closed and fully open to determine the integrity of the PCVS installation and signaling system.

12. Reinstall the cover and tighten the screws to 15 in-lbs minimum to properly seal the enclosure.

13. When the installation and testing are complete, return valve to its proper position.

Typical Installation on a Butterfly Valve
Valve Partially Closed Valve Open
1/2” (13 mm)
Fig 5 Fig 6
1/32”
(0,8 mm)
5401526 - REV F • 8/15
PAGE 5 OF 7
Potter Electric Signal Company, LLC • St. Louis, MO • Tech Support: 866-956-0988 / Customer Service: 866-572-3005 • www.pottersignal.com PCVS Series
Control Valve Supervisory Switch
This figure shows the Model PCVS mounted on the valve yoke, with a bracket supplied by the valve manufacturer, to supervise a pressure reducer type valve.

NOTE: This application is subject to the approval of the authority having jurisdiction.

Pratt Butterfly V alve Kit as used to mount a PCVS on a Pratt Model IBV V alve.

Kits contain: Bracket, nuts and instructions
NOTE: Due to changes in valves, brackets may need to be modified by installer. This application is subject to the approval of the authority having jurisdiction.

Pratt V alve Kit as used to mount a PCVS on a Pratt Model PIV A V alve.

Kit contains: Instructions, template, screw and nut.

NOTE: This application is subject to the approval of the authority having jurisdiction.

Typical Pressure Reducer Type Valve
Installation
PBK - Butterfly Valve Kit for Valves
with Internal Supervisory Switches
Bracket and
Locknut Supplied
With PBK
Mounting Kit
Locknuts Both Sides
Nipple
1/16” (1,6 mm)
Minimum Gap
PVK - Pratt PIVA Post Indicator Valve
Kit
Machine Screw #8-32
Fig 7
Fig 8
Fig 9
Locknut
5401526 - REV F • 8/15
PAGE 6 OF 7
Potter Electric Signal Company, LLC • St. Louis, MO • Tech Support: 866-956-0988 / Customer Service: 866-572-3005 • www.pottersignal.com PCVS Series
Control Valve Supervisory Switch

3.20 81.26

4.00 101.60

2.79 70.87

7.86 199.53

.85

21.51 .77

19.61 1.52

38.61 2.72

69.05 1.10

27.92 .84

21.44 .12

3.05 5.29
134.39

2.25 57.13

3.05 77.47

2.10 53.34

(2) .886 KNOCKOUTS FOR 1/2" ELECTRICAL CONDUIT CONNECTIONS DIMENSIONS APPEARING IN PARENTHESIS [ ]

REPRESENTS EQUVALENT IN MILLIMETERS

ALL DIMENSIONS FOR REFERENCE ONLY
.XX = ENGLISH
[XX.XX] = METRIC

REVISIONS
REV. ENG. CHG. NO. DESCRIPTION DATE BY CHK.

D
C
B
AA
B
C
D

CAD GENERATED DRAWING,

DO NOT MANUALLY UPDATE
SCALE
SIZE DWG. NO.

D
SHEET 1 OF 1

DATEAPPROVALS
DRAWN

CHECKED

TOLERANCES UNLESS SPECIFIED

DECIMALS ANGLES

DO NOT SCALE DRAWING
12345678
8 7 6 5 4 3 2 1
E
F
E
F
POTTER ELECTRIC SIGNAL CO.
-P. REFIOR
-
9/26/2013
- NONE

DATA CONTAINED HEREIN SHALL NOT BE USED, DUPLICATED OR DISCLOSED IN WHOLE OR PART OUTSIDE POTTER ELECTRIC, INC. WITHOUT WRITTEN PERMISSION OF SAME.

PROPRIETARY DATA
PCVS

SUPERVISORY SWITCH
(OULINE DRAWING)

VENDOR CERTIFIES ALL PARTS SUPPLIED FROM THIS DRAWING HAVE BEEN PRODUCED

TO ITS SPECIFICATIONS AND VENDOR WILL BE RESPONSIBLE FOR ANY REWORK COST WHERE SPECIFICATIONS HAVE NOT BEEN MET.

VENDOR CERTIFICATION
TITLE

3.20 81.26

4.00 101.60

2.79 70.87

7.86 199.53

.85

21.51 .77

19.61 1.52

38.61 2.72

69.05 1.10

27.92 .84

21.44 .12

3.05 5.29
134.39

2.25 57.13

3.05 77.47

2.10 53.34

(2) .886 KNOCKOUTS FOR 1/2" ELECTRICAL CONDUIT CONNECTIONS DIMENSIONS APPEARING IN PARENTHESIS [ ]

REPRESENTS EQUVALENT IN MILLIMETERS

ALL DIMENSIONS FOR REFERENCE ONLY
.XX = ENGLISH
[XX.XX] = METRIC

REVISIONS
REV. ENG. CHG. NO. DESCRIPTION DATE BY CHK.

D
C
B
AA
B
C
D

CAD GENERATED DRAWING,

DO NOT MANUALLY UPDATE
SCALE
SIZE DWG. NO.

D
SHEET 1 OF 1

DATEAPPROVALS
DRAWN

CHECKED

TOLERANCES UNLESS SPECIFIED

DECIMALS ANGLES

DO NOT SCALE DRAWING
12345678
8 7 6 5 4 3 2 1
E
F
E
F
POTTER ELECTRIC SIGNAL CO.
-P. REFIOR
-
9/26/2013
- NONE

DATA CONTAINED HEREIN SHALL NOT BE USED, DUPLICATED OR DISCLOSED IN WHOLE OR PART OUTSIDE POTTER ELECTRIC, INC. WITHOUT WRITTEN PERMISSION OF SAME.

PROPRIETARY DATA
PCVS

SUPERVISORY SWITCH
(OULINE DRAWING)

VENDOR CERTIFIES ALL PARTS SUPPLIED FROM THIS DRAWING HAVE BEEN PRODUCED

TO ITS SPECIFICATIONS AND VENDOR WILL BE RESPONSIBLE FOR ANY REWORK COST WHERE SPECIFICATIONS HAVE NOT BEEN MET.

VENDOR CERTIFICATION
TITLE
Dimensions

3.20 81.26

4.00 101.60

2.79 70.87

7.86 199.53

.85

21.51 .77

19.61 1.52

38.61 2.72

69.05 1.10

27.92 .84

21.44 .12

3.05 5.29
134.39

2.25 57.13

3.05 77.47

2.10 53.34

(2) .886 KNOCKOUTS FOR 1/2" ELECTRICAL CONDUIT CONNECTIONS DIMENSIONS APPEARING IN PARENTHESIS [ ]

REPRESENTS EQUVALENT IN MILLIMETERS

ALL DIMENSIONS FOR REFERENCE ONLY
.XX = ENGLISH
[XX.XX] = METRIC

REVISIONS
REV. ENG. CHG. NO. DESCRIPTION DATE BY CHK.

D
C
B
AA
B
C
D

CAD GENERATED DRAWING,

DO NOT MANUALLY UPDATE
SCALE
SIZE DWG. NO.

D
SHEET 1 OF 1

DATEAPPROVALS
DRAWN

CHECKED

TOLERANCES UNLESS SPECIFIED

DECIMALS ANGLES

DO NOT SCALE DRAWING
12345678
8 7 6 5 4 3 2 1
E
F
E
F
POTTER ELECTRIC SIGNAL CO.
-P. REFIOR
-
9/26/2013
- NONE

DATA CONTAINED HEREIN SHALL NOT BE USED, DUPLICATED OR DISCLOSED IN WHOLE OR PART OUTSIDE POTTER ELECTRIC, INC. WITHOUT WRITTEN PERMISSION OF SAME.

PROPRIETARY DATA
PCVS

SUPERVISORY SWITCH
(OULINE DRAWING)

VENDOR CERTIFIES ALL PARTS SUPPLIED FROM THIS DRAWING HAVE BEEN PRODUCED

TO ITS SPECIFICATIONS AND VENDOR WILL BE RESPONSIBLE FOR ANY REWORK COST WHERE SPECIFICATIONS HAVE NOT BEEN MET.

VENDOR CERTIFICATION
TITLE
Rod retracted
and breakaway
section removed
Rod Fully Extended
Socket Head Screw
Cover Removed
Cover Tamper Switch
(Optional)
Ground Screw
Lock Nut
1/2”-14 NPT Nipple
Trip Rod
(2) ø.886
Knockouts For
1/2” Electrical
Conduit
Connections
Fig 10
Fig 11
Knockout Removal
To remove knockouts: Place screwdriver at inside edge of knockouts, not in the center.

NOTE: Do not drill into the base as this creates metal shavings which can create electrical hazards and damage the device. Drilling voids the warranty.
5401526 - REV F • 8/15
PAGE 7 OF 7
Potter Electric Signal Company, LLC • St. Louis, MO • Tech Support: 866-956-0988 / Customer Service: 866-572-3005 • www.pottersignal.com PCVS Series
Control Valve Supervisory Switch
Model Description Stock No.

PCVS-2 Potter Control Valve Switch (double switch) 1010203 PCVS-2
CRH
Potter Control V alve Switch (double switch). Corrosion resistant 316 stainless steel hardware.
1010211
-- Cover Screw 5490424
-- Hex Key for Cover Screws and Installation Adjustments 5250062 PBK-S Pratt Butterfly V alve Kit - 3” (75mm) to 12” (30mm) 0090133 PBK-M Pratt Butterfly V alve Kit - 14” (355 mm) and 16” (406 mm)
0090146
PBK-L Pratt Butterfly V alve Kit - 18" (457mm) to 24” (610 mm) 0090132 PVK Pratt Valve Kit 1000060
-- Optional Cover Tamper Switch Kit 0090200
KBK Kennedy Butterfly V alve Kit 0090143
TBK Tycho Butterfly V alve Kit 0090150
For pressure reducer type valve installation kits (if required) contact valve manufacturer.

Ordering Information
UL, CUL Listed / FM Approved and CE Marked valve supervisory switches shall be furnished and installed on all post Indicator and Butterfly valves that can be used to shut off the flow of water to any portion of the fire sprinkler system, where indicated on the drawings and plans and as required by applicable local and national codes and standards. The supervisory switch shall be NEMA 4X and 6P rated and capable of being mounted in any position indoors or out and be completely submerged without allowing water to enter the enclosure.

The enclosure shall be held captive by tamper resistant screws. The device shall contain two conduit entrances and two Single Pole Double Throw (SPDT) switches. The device shall contain a removable 1/2” NPT nipple and adjustable trip rod, the trip rod shall be held captive by a set screw accessible upon removal of the cover. The switch contacts shall be rated at 10A, 125/250V AC and 2A, 30VDC. Post Indicator and Butterfly V alve supervisory switch shall be model PCVS-2 manufactured by Potter Electric Signal Company LLC
Engineering Specifications: Post
Indicator & Butterfly Valves
Breaking Excessive Rod Length
Typical Electrical Connections

COM NC NO NO NC COM
EOLR

TO FIRE ALARM PANEL
Fig 12
Fig 13
Fig 14
Outgoing
Incoming
Switch Terminal Connections
Clamping Plate Terminal
All conduit and connectors selected for the installation of this product shall be suitable for the environment for which it is to be used and shall be installed to the manufacturer’s installation instructions. For NEMA 4, 4X, 6, 6P installations, the cover screws are recommended to be tightened to 15 in- lbs minimum and the trip rod locking screw tightened to 5 in-lbs minimum to properly seal the enclosure.

An uninsulated section of a single conductor should not be looped around the terminal and serve as two separate connections. The wire must be severed, thereby providing supervision of the connection in the event that the wire become dislodged from under the terminal. Failure to sever the wire may render the device inoperable risking severe property damage and loss of life. Do not strip wire beyond 3/8" of length or expose an uninsulated conductor beyond the edge of the terminal block. When using stranded wire, capture all strands under the clamping plate.

Supervisory switches have a normal service life of 10-15 years.

However, the service life may be significantly reduced by local environmental conditions.

LISTING No.: 7770-0328:0010
CATEGORY: 7770 - VALVES/SWITCHES
LISTEE: Potter Electric Signal Co 1609 Park 370 Place, Hazelwood, MO, 63042 Contact: Lakomiak, Neil 314-816-8679
Email: [email protected]
DESIGN:

Supervisory switches listed below to monitor pressure, OS&Y, gate, globe/gate, PIV, tank temperature or water level valves. Refer to listee's data sheet for detailed product description and operational considerations.

HLS-B WLS-W WLS-S PS-40A PS-120A OSYSU-2 OSYS-B PMS PTS-B OSYSU-1 GVS PCVS-1 PIVS-B TTS-S TTS-W PCVS- 2 WLS PTS-C PS40 PS120 RBVS *PS15 *PS25 RATING:

INSTALLATION:

In accordance with listee's printed instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction.

MARKING:

Listee's name, model designation and FM or UL label.

APPROVAL:

Listed as sprinkler system supervisory switches.

NOTES:

Formerly 7738-0328:010
*Revision 09-07-
2016 dc

Page 1 of 2 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

Date Issued: 05/02/2024 Listing Expires: 06/30/2025
Authorized By: David Castillo, Program Coordinator
Fire Engineering & Investigations Division

Page 2 of 2 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE
5401525 - REV G • 6/19
page 1 OF 6
Potter Electric Signal Company, LLC • St. Louis, MO • Tech Support: 866-956-0988 / Customer Service: 866-572-3005 • www.pottersignal.com OSYSU Series
Outside Screw and Yoke Valve Supervisory Switch
Description
The OSYSU is used to monitor the open position of an OS&Y (outside screw and yoke) type gate valve. This device is available in two models; the OSYSU-1, containing one set of S
pDT (Form C)

contacts and the OSYSU-2, containing two sets of S pDT (Form C)

contacts. These switches mount conveniently to most OS&Y valves ranging in size from 2” to 12” (50mm to 300mm). They will mount on some valves as small as ½” (12,5mm).

The cover is held in place by two tamper resistant screws that require a special tool to remove. The tool is furnished with each device.

Testing
The operation of the OSYSU and its associated protective monitoring system shall be inspected, tested, and maintained in accordance with all applicable local and national codes and standards and/or the authority Having Jurisdiction (manufacturer recommends quarterly or more frequently). a minimum test shall consist of turning the valve wheel towards the closed position. The OSYSU shall operate within

the first two revolutions of the wheel. Fully close the valve and ensure that the OSYSU does not restore. Fully open the valve and ensure that the OSYSU restores to normal only when the valve is fully opened.

Technical Specifications
Dimensions See Fig 8
Weight 1.6 lbs (0,73 kg)
enclosure
Cover: Die Cast Finish: Red powder Coat
Base: Die Cast Finish: Black powder Coat
All parts have corrosion resistant finishes
Cover Tamper T
amper Resistant Screws
Optional Cover Tamper Switch available
Contact
Ratings
OSYSU-1: One Set of SpDT (Form C)
OSYSU-2:

Two Sets of SpDT (Form C)

10.0 amps at 125/250 VaC

2.0 amps at 30VDC Resistive
10 mamps minimum at 24 VDC
environmental
Limitations
-40º F to 140ºF (-40ºC to 60ºC)
NeMa 4X (Ip 65) and NeMa 6p (Ip 67) enclosure
(Use suitably rated conduit and connector)
Indoor or Outdoor Use (See OSYSU-
eX Bulletin
5400705 for Hazardous locations)
Conduit
entrances
Two Knockouts for 1/2” conduit provided
(See Notice on page 6 and Fig. 9 on page 5)
Service Use NF pa 13, 13D, 13R, 72
Features
• NeMa 4X* (Ip 65) and 6p (Ip 67)
*Enclosure is 4X. For additional corrosion pr
otection of
mounting hardware, use model OSYSU-2 CRH
• -40º to 140º (-40ºC to 60ºC) operating temperature range • Visual switch indicators
• Two conduit entrances
• adjustable length trip rod
• accomodates up to 12aWg wire
• Three position switch detects tampering and valve closure • Knurled mounting bracket prevents slipping
• Fine adjustment feature for fast, easy installation
• RoHS compliant
• One or two SpDT contact models (-1,-2)
Important: This document
contains important information on the installation and operation of OS&Y valve supervisory switches. please read all instructions carefully before beginning installation. a copy of this document is required by NFpa 72 to be maintained on site.

Specifications subject to change without notice
Close the valve fully to determine that the stem threads do not activate the switch. The switch being activated by the stem threads could result in a false valve open indication.

Before any work is done on the fire sprinkler or fire alarm system, the building owner or their authorized representative shall be notified.

Before opening any closed valve, ensure that opening the valve will not cause any damage from water flow due to open or missing sprinklers, piping, etc.

CAUTION

5401525 - REV G • 6/19
page 3 OF 6
Potter Electric Signal Company, LLC • St. Louis, MO • Tech Support: 866-956-0988 / Customer Service: 866-572-3005 • www.pottersignal.com OSYSU Series
Outside Screw and Yoke Valve Supervisory Switch
Small Valve Installation
NOTE: If the valve stem is pre-grooved at 1/8” minimum
depth; proceed to step 7.

1. Remove and discard "e" ring and roller from the trip rod.

2. With the valve in the FULL OpeN position, locate the OSYSU across the valve yoke as far as possible from the

valve gland so that the spring loaded trip rod of the OSYSU is pulled against the non threaded portion of the valve stem. position the OSYSU with the bracket near the handwheel as shown in Fig. 6 if possible to avoid creating a pinch point

between the wheel and the OSYSU.

3. Loosen the locking screw that holds the trip rod in place and adjust the rod length (see Fig. 5). When adjusted properly ,
the rod should extend past the valve screw, but not so far that it contacts the clamp bar. Tighten the locking screw to 5 in-lbs minimum to hold the trip rod in place and properly seal the enclosure.

NOTE:

If trip rod length is excessive, loosen the locking
screw and remove the trip rod from the trip lever. Using pliers, break off the one (1) inch long notched section (see Fig. 10). Reinstall trip rod and repeat Step 3 procedure.

4. Mount the OSYSU loosely with the carriage bolts and clamp bar supplied. On valves with limited clearance use J-hooks supplied instead of the carriage bolts and clamp bar to mount

the OSYSU.

5. Mark the valve stem at the center of the trip rod.

6. Remove the OSYSU. Utilizing a 3/16” or 1/4” diameter straight file, file a 1/8” minimum depth groove centered on the mark on the valve stem. Deburr and smooth the edges

of the groove to prevent damage to the valve packing and to allow the trip rod to move easily in and out of the groove as the valve is operated.

NOTE: a groove depth of up to approximately 3/16” can
make it easier to install the OSYSU so that it does not restore as it rolls over by the threads of the valve stem.

7. Mount the OSYSU on the valve yoke with the spring loaded trip rod of the OSYSU pulled against the valve stem and centered in the groove of the stem. If possible, position the

OSYSU with the flat side of the bracket toward the hand wheel, as shown in Fig. 6, to help avoid creating a pinch point between the wheel and OSYSU. When in this preferred mounting position, it is usually best to use the white indicator visible through the window, as illustrated in Fig. 3, to aid in initially locating the OSYSU in the correct position on the yoke. If the unit must be installed inverted with the white indicator no longer easily visible, use the visual indicators of the actuator buttons on the micro-switches, as illustrated in Fig. 1, or the trip rod alignment mark on the bracket, as illustrated in Fig. 2 , to aid in initially locating the OSYSU.

8. Final adjustment can be made by slightly loosening the two screws on the bracket and using the fine adjustment feature (see Fig. 5).

The adjustment is correct when the plungers
on the switches are depressed by the actuator and there is no continuity between the COM and NO terminals on the
switches.

9. Tighten the adjustment screws and all mounting hardware securely (20 in-lbs minimum). Check to insure that the rod

moves out of the groove easily and that the switches activate within two turns when the valve is operated from the FULL O
peN towards the CLOSeD position.

10. Reinstall the cover and tighten the cover screws to 15 in-lbs minimum to properly seal the enclosure.

Small Valve Installation - 1/2” Through 2 1/2” SizesFig 6 A

MOUNTING BRACKET
B

FLAT SCREWDRIVER

MICROADJUSTMENT

FEATURE

CENTER LINE ON ROD
ROLLER

SLOTTED MOUNTING

HOLES MAY BE USED

FOR FINE ADJUSTMENT

OF SWITCH ASSEMBLY

TO MOUNTING BRACKET

DETAIL A
SCALE 1 : 1

LEVERS ARE SHOWN
IN "SETTING" POSITION

WITH ROLLER LOCATED

IN THE GROOVE ON THE

ACME THREAD SHAFT

DETAIL B
SCALE 1 : 1

WHITE LINE THROUGH THE

RECTANGULAR WINDOW
INDICATES "SETTING" POSITION

WITH ROLLER LOCATED IN THE

GROOVE ON THE ACME THREAD
SHAFT
Slotted mounting holes and micro-adjustment
feature may be used for fine adjustment of
switch assembly to mounting bracket.

Re-tighten screws to 20 in-lbs minimum.

Close the valve fully to determine that the stem threads do not activate the switch. The switch being activated by the stem threads could result in a false valve open indication.

CAUTION
5401525 - REV G • 6/19
page 4 OF 6
Potter Electric Signal Company, LLC • St. Louis, MO • Tech Support: 866-956-0988 / Customer Service: 866-572-3005 • www.pottersignal.com OSYSU Series
Outside Screw and Yoke Valve Supervisory Switch
Close the valve fully to determine that the stem threads do not activate the switch. The switch being activated by the stem threads could result in a false valve open indication.

CAUTION
A

MOUNTING BRACKET
B

FLAT SCREWDRIVER

MICROADJUSTMENT

FEATURE

CENTER LINE ON ROD
ROLLER

SLOTTED MOUNTING

HOLES MAY BE USED

FOR FINE ADJUSTMENT

OF SWITCH ASSEMBLY

TO MOUNTING BRACKET

DETAIL A
SCALE 1 : 1

LEVERS ARE SHOWN
IN "SETTING" POSITION

WITH ROLLER LOCATED

IN THE GROOVE ON THE

ACME THREAD SHAFT

DETAIL B
SCALE 1 : 1

WHITE LINE THROUGH THE

RECTANGULAR WINDOW
INDICATES "SETTING" POSITION

WITH ROLLER LOCATED IN THE

GROOVE ON THE ACME THREAD
SHAFT
Large Valve Installation
NOTE: If the valve stem is pre-grooved at 1/8” minimum
depth; proceed to step 6.

1. With the valve in the FULL OpeN position, locate the OSYSU across the valve yoke as far from the valve gland

as possible so that the spring loaded trip rod of the OSYSU is pulled against the non threaded portion of the valve stem. position the OSYSU with the bracket near the handwheel as shown in Fig. 7 if possible to avoid creating a pinch point

between the wheel and the OSYSU.

2. Mount the OSYSU loosely with the carriage bolts and clamp bar supplied.

NOTE: If trip rod length is ex
cessive, loosen the locking
screw and remove the trip rod from the trip lever. Using pliers, break off the one (1) inch long notched section (see Fig. 10). Reinstall trip rod and repeat Step 3 procedure.

4. Mark the valve stem at the center of the trip rod.

5. Remove the OSYSU. Utilizing a 3/8” or ½” diameter straight file, file a 1/8” minimum depth groove centered on the mark on the valve stem. Deburr and smooth the edges of the

groove to prevent damage to the valve packing and to allow the trip rod to move easily in and out of the groove as the valve is operated.

NOTE: a groove depth of up to approximately 3/16” can
make it easier to install the OSYSU so that it does not restore as it rolls over by the threads of the valve stem.

6. Mount the OSYSU on the valve yoke with the spring loaded trip rod of the OSYSU pulled against the valve stem and centered in the groove of the stem. If possible, position the

OSYSU with the flat side of the bracket toward the hand wheel, as shown in Fig. 7, to help avoid creating a pinch point between the wheel and OSYSU. When in this preferred mounting position, it is usually best to use the white indicator visible through the window, as illustrated in Fig. 3, to aid in initially locating the OSYSU in the correct position on the yoke. If the unit must be installed inverted with the white indicator no longer easily visible, use the visual indicators of the actuator buttons on the micro-switches, as illustrated in Fig. 1, or the trip rod alignment mark on the bracket, as illustrated in Fig. 2 , to aid in initially locating the OSYSU.

7. Final adjustment can be made by slightly loosening the two screws on the bracket and using the fine adjustment feature (see Fig. 5).

The adjustment is correct when the plungers
on the switches are depressed by the actuator and there is no continuity between the COM and NO terminals on the
switches.

8. Tighten the adjustment screws and mounting hardware
securely (minimum 20 in-lbs). Check to insure that the rod

moves out of the groove easily and that the switches activate within two turns when the valve is operated from the FULL O
peN towards the CLOSeD position.

9. Reinstall the cover and tighten the cover screws to 15 in-lbs minimum to properly seal the enclosure.

Fig 7
Slotted mounting holes and micro-
adjustment feature may be used for
fine adjustment of switch assembly to
mounting bracket. Re-tighten screws to
20 in-lbs minimum.

Large Valve Installation - 3” Through 12” Sizes
5401525 - REV G • 6/19
page 5 OF 6
Potter Electric Signal Company, LLC • St. Louis, MO • Tech Support: 866-956-0988 / Customer Service: 866-572-3005 • www.pottersignal.com OSYSU Series
Outside Screw and Yoke Valve Supervisory Switch

3.67 93.26

5.69 144.42

2.79 70.87

3.20 81.26

4.00 101.60

6.19 157.23

1.17 29.72

2.25 57.13

3.05 77.47

2.10 53.34

.XX = ENGLISH
[XX.XX] = METRIC
DIMENSIONS APPEARING IN PARENTHESIS [ ]

REPRESENTS EQUVALENT IN MILLIMETERS

ALL DIMENSIONS FOR REFERENCE ONLY
D
C
B
AA
B
C
D

CAD GENERATED DRAWING,

DO NOT MANUALLY UPDATE
SCALE
SIZE DWG. NO.

D
SHEET 1 OF 1

DATEAPPROVALS
DRAWN

CHECKED

TOLERANCES UNLESS SPECIFIED

DECIMALS ANGLES

DO NOT SCALE DRAWING
12345678
8 7 6 5 4 3 2 1
E
F
E
F
POTTER ELECTRIC SIGNAL CO.
-P. REFIOR
-
9/24/2013
- NONE

DATA CONTAINED HEREIN SHALL NOT BE USED, DUPLICATED OR DISCLOSED IN WHOLE OR PART OUTSIDE POTTER ELECTRIC, INC. WITHOUT WRITTEN PERMISSION OF SAME.

PROPRIETARY DATA
OSYSU

SUPERVISORY SWITCH
(OUTLINE DRAWING)

VENDOR CERTIFIES ALL PARTS SUPPLIED FROM THIS DRAWING HAVE BEEN PRODUCED

TO ITS SPECIFICATIONS AND VENDOR WILL BE RESPONSIBLE FOR ANY REWORK COST WHERE SPECIFICATIONS HAVE NOT BEEN MET.

VENDOR CERTIFICATION
TITLE
Dimensions
Fig 8
Fig 9

3.67 93.26

5.69 144.42

2.79 70.87

3.20 81.26

4.00 101.60

6.19 157.23

1.17 29.72

2.25 57.13

3.05 77.47

2.10 53.34

.XX = ENGLISH
[XX.XX] = METRIC
DIMENSIONS APPEARING IN PARENTHESIS [ ]

REPRESENTS EQUVALENT IN MILLIMETERS

ALL DIMENSIONS FOR REFERENCE ONLY
D
C
B
AA
B
C
D

CAD GENERATED DRAWING,

DO NOT MANUALLY UPDATE
SCALE
SIZE DWG. NO.

D
SHEET 1 OF 1

DATEAPPROVALS
DRAWN

CHECKED

TOLERANCES UNLESS SPECIFIED

DECIMALS ANGLES

DO NOT SCALE DRAWING
12345678
8 7 6 5 4 3 2 1
E
F
E
F
POTTER ELECTRIC SIGNAL CO.
-P. REFIOR
-
9/24/2013
- NONE

DATA CONTAINED HEREIN SHALL NOT BE USED, DUPLICATED OR DISCLOSED IN WHOLE OR PART OUTSIDE POTTER ELECTRIC, INC. WITHOUT WRITTEN PERMISSION OF SAME.

PROPRIETARY DATA
OSYSU

SUPERVISORY SWITCH
(OUTLINE DRAWING)

VENDOR CERTIFIES ALL PARTS SUPPLIED FROM THIS DRAWING HAVE BEEN PRODUCED

TO ITS SPECIFICATIONS AND VENDOR WILL BE RESPONSIBLE FOR ANY REWORK COST WHERE SPECIFICATIONS HAVE NOT BEEN MET.

VENDOR CERTIFICATION
TITLE
Rod fully extended
Rod retracted and
breakaway section removed

5.69 144.48

2.79 70.87

3.20 81.26

4.00 101.60

6.19 157.23

3.67 93.21

1.17 29.72

3.04 77.28
REF
.65

16.39 REF

ROD RETRACTED AND

BREAKAWAY SECTION

REMOVED

2.25 57.13

3.05 77.47

2.10 53.34

(2) .886 KNOCKOUTS FOR 1/2" ELECTRICAL CONDUIT CONNECTIONS

ROD FULLY EXTENDED
.XX = ENGLISH
[XX.XX] = METRIC
DIMENSIONS APPEARING IN PARENTHESIS [ ]

REPRESENTS EQUVALENT IN MILLIMETERS

ALL DIMENSIONS FOR REFERENCE ONLY
D
C
B
AA
B
C
D

CAD GENERATED DRAWING,

DO NOT MANUALLY UPDATE
SCALE
SIZE DWG. NO.

D
SHEET 1 OF 1

DATEAPPROVALS
DRAWN

CHECKED

TOLERANCES UNLESS SPECIFIED

DECIMALS ANGLES

DO NOT SCALE DRAWING
12345678
8 7 6 5 4 3 2 1
E
F
E
F
POTTER ELECTRIC SIGNAL CO.
-P. REFIOR
-
12/6/2013
- NONE

DATA CONTAINED HEREIN SHALL NOT BE USED, DUPLICATED OR DISCLOSED IN WHOLE OR PART OUTSIDE POTTER ELECTRIC, INC. WITHOUT WRITTEN PERMISSION OF SAME.

PROPRIETARY DATA
OSYSU

SUPERVISORY SWITCH
(OUTLINE DRAWING)

VENDOR CERTIFIES ALL PARTS SUPPLIED FROM THIS DRAWING HAVE BEEN PRODUCED

TO ITS SPECIFICATIONS AND VENDOR WILL BE RESPONSIBLE FOR ANY REWORK COST WHERE SPECIFICATIONS HAVE NOT BEEN MET.

VENDOR CERTIFICATION
TITLE
Cover Tamper Switch
(Optional)
ground Screw
1/4”-20 Mounting
Hardware
Trip Rod
(2) ø.886
Knockouts For 1/2”
electrical Conduit
Connections
Clamp Bar
Cover Removed
Knockout Removal
To remove knockouts: place screwdriver at inside edge of knockouts, not in the center.

NOTE: Do n
ot drill into the base as this creates metal shavings which can create electrical hazards and damage the device. Drilling voids the warranty.
5401525 - REV G • 6/19
page 6 OF 6
Potter Electric Signal Company, LLC • St. Louis, MO • Tech Support: 866-956-0988 / Customer Service: 866-572-3005 • www.pottersignal.com OSYSU Series
Outside Screw and Yoke Valve Supervisory Switch
Breaking Excessive Rod Length
Typical Electrical Connections
Model Description Stock No.

OSYSU-1 Outside Screw & Yoke
Supervisory Switch
(Single switch)
1010102
OSYSU-2 Outside Screw & Yoke
Supervisory Switch
(Double switch)
1010202
OSYSU-2
CRH
Outside Screw & Yoke Supervisory
Switch (Double Switch). Corrosion
resistant hardware of 316 stainless steel
1010210
Cover Screw 5490424
Hex Key for Cover Screws and
Installation
adjustments
5250062
Optional Cover T
amper Switch Kit 0090200
Ordering Information
Engineering Specifications: OS&Y
Valves
UL, CUL Listed / FM approved and Ce Marked valve supervisory switches shall be furnished and installed on all OS&Y type valves that can be used to shut off the flow of water to any portion of the fire sprinkler system, where indicated on the drawings and plans and as required by applicable local and national codes and standards.

The supervisory switch shall be N
eMa 4X and 6 p rated and capable
of being mounted in any position indoors or out and be completely submer
ged without allowing water to enter the enclosure.. The enclosure shall be held captive by tamper resistant screws. The device shall contain two ½” conduit entrances and one or two Single pole
Double Throw (S pDT) switches. There shall be a visual indicator to
display the status of the switches. To aid in installation, it shall be possible to make fine adjustments to the position of the switch on the valve without loosening the mounting bracket from the valve. The device shall contain an adjustable length trip rod and roller, the trip rod shall be held captive by a set screw accessible upon removal of the cover. The switch contacts shall be rated at 10
a, 125/250VaC and 2a,
30VDC. OS&Y
Valve supervisory switch shall be model OSYSU-1
for the single switch model and OSYSU-2 for the two switch model manufactured by
potter electric Signal Company LLC

COM NC NO NO NC COM
EOLR

TO FIRE ALARM PANEL
Fig 10
Fig 11
Fig 12
Outgoing
Incoming
Switch Terminal Connections
Clamping Plate Terminal
all conduit and connectors selected for the installation of this product shall be suitable for the environment for which it is to be used and shall be installed to the manufacturer’s installation instructions. For N eMa 4, 4X, 6,
6p installations, the cover screws are recommended to be tightened to 15 in- lbs minimum and the trip rod locking screw tightened to 5 in-lbs minimum to properly seal the enclosure.
an uninsulated section of a single conductor should not be looped around the terminal and serve as two separate connections. The wire must be severed, thereby providing supervision of the connection in the event that the wire become dislodged from under the terminal. Failure to sever the wire may render the device inoperable risking severe property damage and loss of life. Do not strip wire beyond 3/8" of length or expose an uninsulated conductor beyond the edge of the terminal block.

When using
stranded wire, capture all strands under the clamping plate.

Supervisory switches have a normal service life of 10-15 years.

However, the service life may be significantly reduced by local environmental conditions.

HLS-B WLS-W WLS-S PS-40A PS-120A OSYSU-2 OSYS-B PMS PTS-B OSYSU-1 GVS PCVS-1 PIVS-B TTS-S TTS-W PCVS- 2 WLS PTS-C PS40 PS120 RBVS *PS15 *PS25 RATING:

INSTALLATION:

In accordance with listee's printed instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction.

MARKING:

Listee's name, model designation and FM or UL label.

APPROVAL:

Listed as sprinkler system supervisory switches.

NOTES:

Formerly 7738-0328:010
*Revision 09-07-
2016 dc

Page 1 of 2 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

Date Issued: 05/02/2024 Listing Expires: 06/30/2025
Authorized By: David Castillo, Program Coordinator
Fire Engineering & Investigations Division

Page 2 of 2 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE
VSR
Vane Type Waterflow Alarm Switch W/ Retard
5401146 - REV N • 10/21
PAGE 1 OF 5
Potter Electric Signal Company, LLC • St. Louis, MO • Phone: 800-325-3936 • www.pottersignal.com Conduit
Entrances
Two knockouts provided for 1/2" conduit. Individual
switch compartments suitable for dissimilar voltages
Contact
Ratings
Two sets of SPDT (Form C)

10.0 Amps at 125/250V AC

2.0 Amps at 30VDC Resistive
10 mAmps min. at 24VDC
Enclosure
Cover - Weather/UV/Flame Resistant High Impact
Composite
Base - Die-cast aluminum
Environmental
Specifications
NEMA 4/IP54 Rated Enclosure suitable for indoor or
outdoor use with factory installed gasket when used with appropriate conduit fitting.

Temperature Range: 40°F - 120°F, (4.5°C - 49°C) - UL
Non-corrosive sleeve factory installed in saddle.

Flow
Sensitivity
Range for
Signal
4-10 GPM (15-38 LPM) - UL
Maximum
Surge 18 FPS (5.5 m/s)
Service
Pressure 450 PSI (31 BAR) - UL
Service Use
Automatic Sprinkler NFPA-13 One or two family dwelling NFPA-13D Residential occupancy up to four stories NFPA-13R

National Fire Alarm Code NFPA-72
Technical Specifications
• Installation must be performed by qualified personnel and in accordance with all national and local codes and ordinances. • Shock hazard. Disconnect power source before servicing. Serious injury or death could result.
• Risk of explosion. Not for use in hazardous locations. Serious injury or death could result.

Waterflow switches
that are monitoring wet pipe sprinkler systems shall
not be used as the sole initiating device to discharge AFFF, deluge, or chemical suppression systems. Waterflow switches used for this application may result in unintended discharges caused by surges, trapped air, or short retard times.

Description
The Model VSR is a vane type waterflow switch for use on wet sprinkler systems. It is UL Listed for use on a steel pipe; schedules 5 through 40, sizes 2" - 6" and is UL Listed and FM Approved for use on steel pipe; schedules 10 through 40, sizes 2" thru 8" (50 mm thru 200 mm). LPC approved sizes are 2" thru 8" (50 mm thru 200 mm). See Ordering Information chart.

The VSR may also be used as a sectional waterflow detector on large systems. The VSR contains two single pole, double throw, snap action switches and an adjustable, instantly recycling pneumatic retard. The switches are actuated when a flow of 10 GPM (38 LPM) or more occurs downstream of the device. The flow condition must exist for a period of time necessary to overcome the selected retard period.

Enclosure
The VSR switches and retard device are enclosed in a weather/UV/ flame resistant high impact composite plastic. The cover is held in place with two tamper resistant screws which require a special key for removal. A field installable cover tamper switch is available as an option which may be used to indicate unauthorized removal of the cover. See bulletin number 5401103 for installation instructions of this switch.

Specifications subject to change without notice.

Features
• Assembled in USA
• 0-90 seco
nd field replaceable time delay retard
• Easy t
o read retard time delay adjustment knob
• UL Lis
ted models for 2"-6" steel pipe schedules 5 through 40
• UL Lis
ted and FM approved models for 2"-8" steel pipe schedules 10 through 40
• Two S
PDT (form C) contacts
• Wea
therproof
• Easy t
o read wire terminal designations
NOTICE
This document contains important information on the installation and operation of the VSR. Please read all instructions carefully and notify the building owner or their authorized representative before any work is done on the fire sprinkler or fire alarm system. A copy of this document is required by NFPA 72 to be maintained on site.

VSR
Vane Type Waterflow Alarm Switch W/ Retard
5401146 - REV N • 10/21
PAGE 2 OF 5
Potter Electric Signal Company, LLC • St. Louis, MO • Phone: 800-325-3936 • www.pottersignal.com Installation (see Fig. 1)
These devices may be mounted on horizontal or vertical pipe. On horizontal pipe they shall be installed on the top side of the pipe where they will be accessible. The device should not be installed within 6" (15 cm) of a fitting which changes the direction of the waterflow or within 24" (60 cm) of a valve or drain.

NOTE: Do not leave cover off for an extended period of time.

Drain the system and drill a hole in the pipe using a hole saw in a slow speed drill (see Fig. 1). Clean the inside pipe of all growth or other material for a distance equal to the pipe diameter on either side of the hole. Roll the vane so that it may be inserted into the hole; do not bend or crease it.

Insert the vane so that the arrow on the saddle points in the direction of the waterflow. Take care not to damage the non-corrosive bushing in the saddle. The bushing should fit inside the hole in the pipe. Install the saddle strap and tighten nuts alternately to required torque (see the chart in Fig. 1). The vane must not rub the inside of the pipe or bind in any way.

ADAPTER
USE (2) 5180162 ADAPTERS AS SHOWN ABOVE
DN50 ONLY

ADAPTER
50mm
20mm ±2mm MAX.

DWG# 1146-1F
Fig. 1 Retard Adjustment
The delay can be adjusted by rotating the retard adjustment knob from 0 to the max setting (60-90 seconds). The time delay should be set at the minimum required to prevent false alarms(Flowing water activates device in one direction only.)

DO NOT LEAVE COVER OFF FOR

AN EXTENDED PERIOD OF TIME

TIGHTEN NUTS

ALTERNATELY

MOUNT ON PIPE SO

ARROW ON SADDLE

POINTS IN DIRECTION

OF WATERFLOW

ROLL PADDLE IN

OPPOSITE DIRECTION

OF WATERFLOWDIRECTION OF

WATERFLOW
Hole must be drilled perpendicular to the pipe and vertically centered.

Refer to the Compatible Pipe/Installation Requirements chart for size.

Correct Incorrect
Compatible Pipe/ Installation Requirements
Model Nominal Pipe
Size
Nominal Pipe
O.D.

Pipe Wall Thickness Hole Size U-Bolt Nuts
TorqueLightwall Schedule 10 (UL) Schedule 40 (UL) BS-1387 (LPC) DN (VDS) inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm ft-lb n-m VSR-2 2 DN50 2.375 60.3 .065 1.651 0.109 2.77 0.154 3.91 0.142 3.6 0.091 2.3

1.25 + .125/-.062 33.0 ± 2.0
20 27
VSR-2 1/2 2.5 - 2.875 73.0 .084 2.134 0.120 3.05 0.203 5.16 - - - - VSR-2 1/2 - DN65 3.000 76.1 - - - - - - 0.142 3.6 0.102 2.6 VSR-3 3 DN80 3.500 88.9 .083 2.108 0.120 3.05 0.216 5.49 0.157 4.0 0.114 2.9

2.00 ± .125 50.8 ± 2.0
VSR-3 1/2 3.5 - 4.000 101.6 - - 0.120 3.05 0.226 5.74 - - - - VSR-4 4 DN100 4.500 114.3 .084 2.134 0.120 3.05 0.237 6.02 0.177 4.5 0.126 3.2 VSR-5 5 - 5.563 141.3 - - 0.134 3.40 0.258 6.55 - - - - VSR-6 6 DN150 6.625 168.3 .115 2.921 0.134 3.40 0.280 7.11 0.197 5.0 0.157 4.0 VSR-8 8 DN200 8.625 219.1 - - 0.148 3.76 0.322 8.18 0.248 6.3 0.177 4.5 Do not trim the paddle. Failure to follow these instructions may prevent the device from operating and will void the warranty. Do not obstruct or otherwise prevent the trip stem of the flow switch from moving when water flows as this could damage the flow switch and prevent an alarm. If an alarm is not desired, a qualified technician should disable the alarm system.

VSR
Vane Type Waterflow Alarm Switch W/ Retard
5401146 - REV N • 10/21
PAGE 3 OF 5
Potter Electric Signal Company, LLC • St. Louis, MO • Phone: 800-325-3936 • www.pottersignal.com To remove knockouts: Place screwdriver at
inside edge of knockouts, not in the center.

DWG 1146-4
Fig. 2
NOTICE
Do not drill into the base as this
creates metal shavings which can
create electrical hazards and damage
the device. Drilling voids the warranty.

Switch Terminal Connections
Clamping Plate Terminal
Fig. 3
Break out thin section of cover when wiring
both switches from one conduit entrance.

Testing
The frequency of inspection and testing for the Model VSR and its associated protective monitoring system shall be in accordance with applicable NFPA Codes and Standards and/or the authority having jurisdiction (manufacturer recommends quarterly or more frequently).

If provided, the inspector’s test valve shall always be used for test purposes. If there are no provisions for testing the operation of the flow detection device on the system, application of the VSR is not recommended or advisable.

A minimum flow of 10 GPM (38 LPM) is required to activate this device.

Fig. 6 Mounting Dimensions
DWG. 1146-14

3.50 in
(89.0 mm)

2.34 in
(59.4 mm)
PIPE DIA.
+ 5.25 in
(+ 133.4 mm)

5.56 in
(141.2 mm)2.00 in
(50.8 mm)
U-BOLT
NUT
U-BOLT
WASHER
PIPE
SADDLE
PIPE

PLASTIC
PADDLEU-BOLT NOMINAL PIPE DIA. +1.75 in (+44.5 MM) FOR DN 50 – DN 65 2–2.5 in NOMINAL PIPE DIA. +2.125 in (+54.0 MM) FOR DN 80 – DN 200 3–8 in DWG 1146-15

GREEN GROUND
SCREWS
Fig. 7
An uninsulated section of a single conductor should not be looped around the terminal and serve as two separate connections. The wire must be severed, thereby providing supervision of the connection in the event that the wire become dislodged from under the terminal. Failure to sever the wire may render the device inoperable risking severe property damage and loss of life.

Do not strip wire beyond 3/8" of length or expose an uninsulated conductor beyond the edge of the terminal block. When using stranded wire, capture all strands under the clamping plate.

Notes:

1. The Model VSR has two switches, one can be used to operate a central station, proprietary or remote signaling unit, while the other contact

is used to operate a local audible or visual annunciator.

2. For supervised circuits, see “Switch Terminal Connections”

drawing and warning note (Fig. 4).

Typical Electrical Connections

LOAD TO BELL

NEUTRAL FROM BELL

CONNECTOR
EOL (End Of Line Resistor)
BELL

NEUTRAL FROM

BREAKER

LINE FROM BREAKER
NOTE:

When connecting to a UL Listed
control panel, use the panel’s
resistor value for circuit supervision.

Fig. 4
Fig. 5
Advise the person
responsible for testing of
the fire protection system
that this system must be
tested in accordance with
the testing instructions.

NOTICE
VSR
Vane Type Waterflow Alarm Switch W/ Retard
5401146 - REV N • 10/21
PAGE 4 OF 5
Potter Electric Signal Company, LLC • St. Louis, MO • Phone: 800-325-3936 • www.pottersignal.com Fig. 8
Retard/Switch Assembly Replacement (See Fig. 8)

1. Make sure the fire alarm zone or circuit connected to the waterflow switch is bypassed or otherwise taken out of service.

2. Disconnect the power source for local bell (if applicable).

3. Identify and remove all wires from the waterflow switch.

4. Remove the (2) mounting screws holding retard/switch assembly to the base. Do not remove the (2) retard housing screws.

5. Remove the retard assembly by lifting it straight up over the tripstem.

6. Install the new retard assembly. Make sure the locating pins on the retard/switch assembly fit into the locating pin bosses on the base.

7. Re-install the (2) original mounting screws.

8. Reconnect all wires. Perform a flow test and place the system back in service.

Maintenance
Inspect detectors monthly. If leaks are found, replace the detector. The VSR waterflow switch should provide years of trouble-free service. The retard and switch assembly are easily field replaceable. In the unlikely event that either component does not perform properly, please order replacement retard switch assembly stock #1029030 (see Fig. 8). There is no maintenance required, only periodic testing and inspection.

DWG# 1146-10

BREAK OUT THIN SECTION OF COVER

WHEN WIRING BOTH SWITCHES
FROM ONE CONDUIT ENTRANCE.

DO NOT REMOVE
(2) RETARD HOUSING
SCREWS
REMOVE (2) ORIGINAL MOUNTING

SCREWS HOLDING RETARD/SWITCH

ASSEMBLY TO BASE

RETARD/SWITCH ASSEMBLY
(2) ORIGINAL MOUNTING
SCREWS
(2) LOCATING PINS
(2) LOCATING PIN

BOSSES IN BASEBASE
NOTICE
The Retard/Switch Assembly is field-replaceable without draining the system or removing the waterflow switch from the pipe VSR
Vane Type Waterflow Alarm Switch W/ Retard
5401146 - REV N • 10/21
PAGE 5 OF 5
Potter Electric Signal Company, LLC • St. Louis, MO • Phone: 800-325-3936 • www.pottersignal.com Removal of Waterflow Switch
• To prevent accidental water damage, all control valves should be shut tight and the system completely drained before waterflow detectors are removed or replaced.
• Turn off electrical power to the detector, then disconnect wiring. • Loosen nuts and remove U-bolts.
• Gently lift the
saddle far enough to get your fingers under it. With your fingers, roll the vane so it will fit through the hole while continuing to lift the waterflow detector saddle.
• Lift detector clear of pipe.

Model Nominal Pipe Size Part Number
VSR-2 2" DN50 1144402
VSR-2 1/2 2 1/2" DN65 1144425
VSR-3 3" DN80 1144403
VSR-3 1/2 3 1/2" - 1144435
VSR-4 4" DN100 1144404
VSR-5 5" - 1144405
VSR-6 6" DN150 1144406
VSR-8 8" DN200 1144408
Optional: Cover Tamper Switch Kit, stock no. 0090148
FSBS-FLOWSWITCH BYPASS SWITCH, stock no. 3001006
Replaceable Components: Retard/Switch
Assembly, stock no. 1029030
Ordering Information
NOTICE
Flow switches have a normal service life of 10-15 years.

However, the service life may be significantly reduced by local environmental conditions.

LISTING No.: 7770-0328:0001
CATEGORY: 7770 - VALVES/SWITCHES
LISTEE: Potter Electric Signal Co 1609 Park 370 Place, Hazelwood, MO, 63042 Contact: Lakomiak, Neil 314-816-8679
Email: [email protected]
DESIGN:

Vane and pressure type water flow alarm switches listed below. Refer to listee's data sheet for detailed product description and operational considerations.

Vane Types:

VSR-CF VSR-D VSR-F VSR-SF VSR-FE-2 VS-SP VS-F VSR-SFG VSR-SFT VSG VSR VSR-S VSR-C VSR-ST VSR-SG

Pressure Type:

WFS-B WFSR-C WFSPD-B PS10 PS-10A PS-100A WFSR-F PS100 RATING:

INSTALLATION:

In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction.

MARKING:

Listee's name, model number and UL or FM label.

Page 1 of 2 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE
APPROVAL:

Listed as waterflow alarm switches for use with fire sprinkler systems. Vane models may be used in wet pipe systems; pressure models may be used in wet or dry systems. Model VSR-CF is for use on K, L or M copper pipe (2", 2-1/2", 3", 4") and listed CPVC pipe (2", 2-1/2", 3"). Model VSR-SF for use on 1", 1-1/4", 1-1/2" and *2” steel, copper or listed plastic pipe. Model VSG is for low flow rate. Model VSR-SFG and VSR-SFT are for use on 1", 1-1/4", 1-1/2" and *2” plastic pipe. Models VS-F, VSR-F, VSR-FE and VSR-FE-2 is for use on 2", 2-1/2", 3", 3-1/2", 4", 5", 6", 8" and 10" pipe. *Model VSR is for use on steel pipe sizes from 2" through 8". Vane type switches may be used outdoors when the outdoor temperature never falls below 40oF.

NOTES:

Date Issued: 05/02/2024 Listing Expires: 06/30/2025
Authorized By: David Castillo, Program Coordinator
Fire Engineering & Investigations Division
Rev*5-17-2007 jw

Page 2 of 2 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE

LISTING No.: 7135-1653:0217
CATEGORY: 7135 - AUDIBLE DEVICES
LISTEE: System Sensor, Unincorporated Div of Honeywell Int'l Inc. 3825 Ohio Ave, St. Charles, IL, 60174
Contact: Brant,Lisa (203) 484-6105 (203) 484-7309
Email: [email protected]
DESIGN:

Models SSM24-6, -8, -10 and SSV120-6, -8, -10 audible signal devices. Models are AC or DC powered and available in 6", 8" and 10" bells. Refer to listee's data sheet for detailed product description and operational considerations.The units may be employed outdoors when used with NEMA 3R weather resistant back box Model WBB.

RATING:

SSM24-6 Sound output: 82 dBA
SSM24-8 Sound output: 80 dBA
SSM24-10 Sound output: 81 dBA
SSV120-6 Sound output: 85 dBA
SSV120-8 Sound output: 82 dBA
SSV120-10 Sound output: 82 dBA
SSM Series Voltage Range: 16-33 VDC
SSV Series Voltage Range: 96-132 VAC
Temperature Range: -31°F to 150° F (-35°C to 66°C)
INSTALLATION:

In accordance with listee's printed installation instruction, applicable codes & ordinances, and in a manner acceptable to the authority having jurisdiction.

MARKING:

Listee's name, model number and UL label.

APPROVAL:

Listed as audible devices for use with separately listed compatible fire alarm control units. If this appliance is required to produce a distinctive three-pulse Temporal Pattern Fire Alarm Evacuation Signal (for total evacuation) in accordance with NFPA 72, 2002 Edition, the appliance must be used with a fire alarm control unit that can generate the temporal pattern signal. Refer to manufacturer’s Installation Manual for details.

NOTES:
07-30-10 fm

Page 1 of 2 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

Date Issued: 05/03/2024 Listing Expires: 06/30/2025
Authorized By: David Castillo, Program Coordinator
Fire Engineering & Investigations Division

Page 2 of 2 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE
MR-100, 200 SERIES

MULTI-VOLTAGE CONTROL REL AYS

PRODUCT DESCRIPTION
The MR Series Multivoltage Control Relays offer SPDT or DPDT 10 Amp resistive contacts which may be operated by one of four input control voltages. A single relay may be energized from a voltage source of 24VDC, 24VAC, 120VAC or 230VAC by wiring to appropriate input terminals.

Each relay position contains a red LED which indicates the relay coil is energized. Relays may be “snapped apart” from a standard 4 module assembly and used independently. These Devices are Ideal for applications where local contacts are required for system status, remote contacts for control of electrical loads and general purpose switching. They are suitable for use with HVAC, T emperature Control, Fire Alarm, Security, Energy Management and Lighting Control Systems.

FEATURES
❖ Relays may be energized from a voltage source of 18 to 35VDC or VAC, 120VAC or 230VA
C
❖ Each relay position contains a red LED, which illuminates when the coil is energized. This pro
vides a time saving device when checking an installed
system – no metering is required
❖ Single, dual or triple relay modules may be “snapped apart” from standard 4-position master ❖ DC control inputs are polarized
❖ For continuous duty use at 24VAC, 24VDC or 120VAC
(NOTE: Not intended for continuous duty use @ 230VAC)
❖ Available in dust resistant enclosures with LED viewing port(s) ❖ /C versions mounted in enclosures
❖ /C/R versions with red covers for NYC and other uses
❖ /T versions come complete with track mounting hardware which facilitates installation in standard cabinets
❖ UL recognized relays rated at 10,000,000 mechanical operations ❖ UL listed as Control Unit Accessory
WIRING
(TYPICAL FOR ONE

MODULE POSITION)
Distributed By:

Air Products and Controls is
a Brand of Apollo America
25 Corporate Drive
Auburn Hills, MI 48326
(248) 332-3900 Phone
(888) 332-2241 Toll free
(248) 332-8807 Fax
www.ap-c.com

MEA ACCEPTED

CSFM LISTED
You in Control
AND

AIR PRODUCTS

CONTROLS
DS-RL-2 C050831© Air Products and Controls Inc. 2013
NOTICE: The information contained in this document is intended only as a summary and is subject to change without notice. The products described have speciﬁc instructional/installation documentation, which covers various technical, approval, code, limitation and liability information. Copies of this documentation along with any gen- eral
product warning and limitation documents, which also contain important information, are provided with the product and are also available from Air Products and Controls Inc. The information contained in all of these documents should be considered before specifying or using the products. Any example applications shown are subject to the most current enforced local/national codes, standards, approvals, certiﬁcations, and/or the authority having jurisdiction. All of these resources, as well as the speciﬁc manufacturer of any shown or mentioned related equipment, should be consulted prior to any implementation. For further information or assistance concerning the products, contact Air Products and Controls Inc. Air Products and Controls Inc. reserves the right to change any and all documentation without notice.

PRODUCT SPECIFICATIONS

MODEL
NUMBER:

MR-101/T
MR-101/C
MR-101/C/R
MR-104/T
MR-104/C
MR-104/C/R
MR-201/T
MR-201/C
MR-201/C/R
MR-204/T
MR-204/C
MR-204/C/R
COIL VOLTAGE: MR-100: 24(18-35)VDC, 24(18-35)V
AC, 120VAC, 230VAC
MR-200: 24(18-35)VDC, 24VAC, 120VAC, 230VAC
(Pull in voltage: 75% of nominal max. @ 25°C; Drop out voltage: 25% of nominal min. @ 25°C) POLARIZED: DC input only
ENERGIZED LED INDICATOR: One per module position
CURRENT REQUIREMENT: Per module position: MR-100 Series = 18mA / MR-200 Series = 40mA CONTACT RATINGS: 7A @ 28VDC / 10A (NO:1/6HP, NC:1/8HP) @ 120VAC / 7A @ 230VAC CONTACT CONSTRUCTION: Dry Form “C”
ENVIRONMENTAL: 32°F to 120°F (0°C to 49°C) @ 85% RH (@ 32°F), Non-condensing, Non-freezing WIRING: Solid or stranded; #14 to #22
AWG terminals
/T VERSIONS: 3.5” wide, low proﬁle plastic snap track provided with mounting screws /C VERSIONS: Backbox: 18ga CRS, plated with 1/2” conduit knockouts top and bottom *UOXX=Control Unit Accessories, System; 2=Component; 7=Certiﬁed for Canada MODULE

POSITIONS
1 1
1 4
4 4
1 1
1 4
4 4

CONTACT

CONFIGURATION

PER POSITION
SPDT
SPDT
SPDT
SPDT
SPDT
SPDT
DPDT
DPDT
DPDT
DPDT
DPDT
DPDT
TRACK

MOUNTED

H X W X D

3.25” (82mm)

2.125” (54mm)

1.50” (38mm)

3.25” (82mm)

8.50” (215mm)

1.50” (38mm)

3.25” (82mm)

2.125” (54mm)

1.50” (38mm)

3.25” (82mm)

8.5” (215mm)

1.50” (38mm)

ENCLOSURE

MOUNTED

H X W X D

5.125” (130mm)

3.125” (79mm)

2.50” (63mm)

5.125” (130mm)

9.50” (241mm)

2.50” (63mm)

5.125” (130mm)

3.125” (79mm)

2.50” (63mm)

5.125” (130mm)

9.50” (241mm)

2.50” (63mm)
COVER

MATERIAL
Grey
ABS-94VO
Plastic
Red
ABS-94VO
Plastic
Plated
18ga
CRS
Red
18ga
CRS
Grey
ABS-94VO
Plastic
Red
ABS-94VO
Plastic
Plated
18ga
CRS
Red
18ga
CRS
UL*
FILE
S3403
UOXX2
UOXX
UOXX2
UOXX7
UOXX2
UOXX
UOXX2
UOXX7
UOXX2
UOXX
UOXX2
UOXX7
UOXX2
UOXX
UOXX2
UOXX7
MEA
FILE
73-92-E
Vol. 14
Vol. 22
V
ol. 14
Vol. 16
V
ol. 22
Vol. 16
CSFM
FILE
7300-1004
:106
:101
:106
:101
:106
:101
:106
:101
LISTING No.: 7300-1004:0101
CATEGORY: 7300 - FIRE ALARM CONTROL UNIT ACCESSORIES/MISC. DEVICES LISTEE: Apollo America Inc. 30 Corporate Drive, Auburn Hills, MI, 48326 Contact: Howells,Dale (248) 563-8405 (248) 332-8807
Email: [email protected]
DESIGN:

Models MR-101/C, *MR-101/C/R, *MR-101-SSE/C, *MR-101-SSE/C/R, MR-104/C, *MR_104/C/R, *MR- 104-SSE/C, *MR-104-SSE/C/R, MR-201/C, MR-201/C/*R, *MR-201-SSE/C, *MR-201-SSE/C/R, MR- 204/C, MR-204/C/*R, *MR-204-SSE/C, *MR-204-SSE/C/R, PAM-1, PAM-2, PAM-3, PAM-4, PAM-SD, RIC-1, RIC-2, RIC-3, RIC-4, MR-RIC-301/*C, *MR-RIC-301/C/R, MR-RIC-305*/C, * MR-RIC-305/C/R, MR-RIC-401*/C, *MR-RIC-401/C/R, MR-RIC-405*/C and *MR-RIC-405/C/R relay modules. *Models MR- ITM/C and MR-ITM/C/R relay modules (with test mode). Refer to listee's data sheet for detailed product description and operational considerations.

RATING:

INSTALLATION:

In accordance with listee's printed installation instruction, applicable codes & ordinances and in a manner acceptable to the authority having jurisdiction.

MARKING:

Listee's name, electrical rating and UL label.

APPROVAL:

Listed as relay modules for use with separately listed compatible fire alarm control units. Refer to manufacturer’s Installation Manual for details.

NOTES:

1. Formerly Air Products and Controls, Inc.

Date Issued: 06/03/2024 Listing Expires: 06/30/2025
Authorized By: David Castillo, Program Coordinator
Fire Engineering & Investigations Division
*Rev. 04-03-14 gt

Page 1 of 1 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE

Technical Data Sheet
Fire Alarm Cables- Addressable

PART NUMBER: D990

DESCRIPTION: 16/2 Solid bare copper conductors, unshielded with an overall jacket.

NEC RATING: FPLR, NEC Article 760

APPROVALS: (UL) Listed

APPLICATION: Indoor data fire alarm cable for (Data Circuits, Initiating Circuits, Notification Circuits, Addressable Systems)

Construction Parameters:

Conductor 16 AWG Bare Copper
S t r a n d i n g S o l i d
Insulation Material Copolene
Insulation Thickness 0.015'' Nom.

Number of Conductors 2
S h i e l d N o n e
D r a i n N o n e
J a c k e t M a t e r i a l P V C
Jacket Thickness 0.030'' Nom.

Overall Cable Diameter 0.223'' Nom.

Approximate Cable Weight 29 Lbs/1M' Nom.

Flame Rating UL 1666 Riser Flame Test

Electrical & Environmental Properties:

Temperature Rating -20deg C to 60deg C
Operating Voltage 300 V RMS
Max.Capacitance Between Conductors @ 1 KHz 18 pf/ft Nom.

DC Resistance per Conductor @ 20deg C 4.2 Ohms/1M' Nom.

Velocity of Propagation 71% Nom.

Insulation Colors Black, Red
J a c k e t C o l o r R e d
R o H S C o m p l i a n t - -

Mechanical Properties:

Max. Recommended Pull Tension 62.4 lbs.

Min. Bend Radius (Install) 2.25”

Specification Issue Date: 7/06

2833 West Chestnut Street
Washington, PA 15301
Toll Free: (800) 245-4964
Fax: (724) 222-6420
www.westpenn-wpw.com
Standard Lengths are 1000ft.

The Jacket is sequentially footmarked.

The information presented here is, to the best of our
knowledge, is true and accurate. However, since
conditions of use are beyond our control, all
recommendations or suggestions are presented
without guarantee or responsibility on our part. We
disclaim all liability in connection with the use of
information contained herein or otherwise.

This document is the property of West Penn Wire.

The information contained herein is considered
Proprietary and not to be reproduced by any means
Without written consent of West Penn Wire

Technical Data Sheet
Fire Alarm Cables

PART NUMBER:

D991

DESCRIPTION: 16/2 Solid bare copper conductors, shielded with an overall jacket.

NEC RATING: FPLR, NEC Article 760

APPROVALS: (UL) Listed

APPLICATION: Indoor data fire alarm cable for (Data Circuits, Initiating Circuits, Notification Circuits, Addressable Systems)

Construction Parameters:

Conductor 16 AWG Bare Copper
S t r a n d i n g S o l i d
Insulation Material Polyolefin
Insulation Thickness 0.015'' Nom.

Number of Conductors 2
Shield 100% Aluminum Polyester Foil
Drain Stranded Tinned Copper
J a c k e t M a t e r i a l P V C
Jacket Thickness 0.030'' Nom.

Overall Cable Diameter 0.226'' Nom.

Approximate Cable Weight 33 Lbs/1M' Nom.

Flame Rating UL 1666 Riser Flame Test

Electrical & Environmental Properties:

Temperature Rating -20deg C to 60deg C
Operating Voltage 300 V RMS
Max.Capacitance Between Conductors @ 1 KHz 30 pf/ft Nom.

Capacitance Between Conductors to Shield @ 1 KHz 54 pf/ft Nom.

DC Resistance per Conductor @ 20deg C 4.1 Ohms/1M' Nom.

Velocity of Propagation 71% Nom.

Insulation Colors Black, Red
J a c k e t C o l o r R e d
R o H S C o m p l i a n t - -

Mechanical Properties:

Max. Recommended Pull Tension 76.4 lbs.

Min. Bend Radius (Install) 2.25”

Specification Issue Date: 7/06

2833 West Chestnut Street
Washington, PA 15301
Toll Free: (800) 245-4964
Fax: (724) 222-6420
www.westpenn-wpw.com
Standard Lengths are 1000ft.

The Jacket is sequentially footmarked.

This document is the property of West Penn Wire.

The information contained herein is considered
Proprietary and not to be reproduced by any means
Without written consent of West Penn Wire

Technical Data Sheet
Aquaseal® Communication Cables

PART NUMBER: AQC225

DESCRIPTION: 16/2 Stranded bare copper conductors, unshielded with an Aquaseal tape and overall jacket.

NEC RATING: CM / CL3 / FPL, NEC Article 800, 725, and 760

APPROVALS: (UL) Listed

APPLICATION: Materials suitable for outdoor use, and indoor trays, allows a variety of uses for (Intercom, Security, Sound, Audio, Background music, and Fire Alarm Circuits)

Construction Parameters:

Conductor 16 AWG Bare Copper
Stranding 19x29
Insulation Material PVC
Insulation Thickness 0.010'' Nom.

Number of Conductors 2
S h i e l d N o n e
D r a i n N o n e
Water-Blocking Tape 2 ply water swellable tape
J a c k e t M a t e r i a l S unlight/Moisture Resistance PVC Jacket Thickness 0.025'' Nom.

Overall Cable Diameter 0.242'' Nom.

Approximate Cable Weight 52 Lbs/1M' Nom.

Flame Rating UL 1685 Vertical Tray

Electrical & Environmental Properties:

Temperature Rating -20deg C to 60deg C
Operating Voltage 300 V RMS
Max.Capacitance Between Conductors @ 1 KHz 35 pf/ft Nom.

DC Resistance per Conductor @ 20deg C 4.2 Ohms/1M' Nom.

Insulation Colors Black, Red
J a c k e t C o l o r G r a y
R o H S C o m p l i a n t - -
TIA455-82B Water Infiltration Test Compliant Yes
UL 444 & 13 Compliant Yes

Mechanical Properties:

Max. Recommended Pull Tension 54 lbs.

Min. Bend Radius (Install) 2.4”

Specification Issue Date: 4/12

2833 West Chestnut Street
Washington, PA 15301
Toll Free: (800) 245-4964
Fax: (724) 222-6420
www.westpenn-wpw.com
Standard Lengths are 1000ft.

The Jacket is sequentially footmarked.

This document is the property of West Penn Wire.

The information contained herein is considered
Proprietary and not to be reproduced by any means
Without written consent of West Penn Wire

Technical Data Sheet
Aquaseal® Audio and Alarm

PART NUMBER: AQC294

DESCRIPTION: 16/2 Stranded bare copper conductors, shielded with an Aquaseal tape and overall jacket.

NEC RATING: CM / CL3 / FPL, NEC Article 800, 725, and 760

APPROVALS: (UL) Listed

APPLICATION: Materials suitable for outdoor use, and indoor trays, allows a variety of uses for (Intercom, Security, Sound, Audio, Background music, and Fire Alarm Circuits)

Construction Parameters:

Conductor 16 AWG Bare Copper
Stranding 19x29
Insulation Material PVC
Insulation Thickness 0.010'' Nom.

Number of Conductors 2 (1 Pair)
Shield 100% Aluminum Polyester Foil
Drain 24AWG Stranded Tinned Copper
Water-Blocking Tape 2 ply water swellable tape
J a c k e t M a t e r i a l S unlight/Moisture Resistance PVC Jacket Thickness 0.025'' Nom.

Overall Cable Diameter 0.281'' Nom.

Approximate Cable Weight 55 Lbs/1M' Nom.

Flame Rating UL 1685 Vertical Tray

Electrical & Environmental Properties:

Temperature Rating -20deg C to 60deg C
Operating Voltage 300 V RMS
Max.Capacitance Between Conductors @ 1 KHz 46 pf/ft Nom.

Capacitance Between Conductors to Shield @ 1 KHz 83 pf/ft Nom.

DC Resistance per Conductor @ 20deg C 4.2 Ohms/1M' Nom.

Insulation Colors Black, Red
J a c k e t C o l o r G r a y
R o H S C o m p l i a n t - -
TIA455-82B Water Infiltration Test Compliant Yes
UL 444 & 13 Compliant Yes

Mechanical Properties:

Max. Recommended Pull Tension 67 lbs.

Min. Bend Radius (Install) 2.8”

Specification Issue Date: 4/12

2833 West Chestnut Street
Washington, PA 15301
Toll Free: (800) 245-4964
Fax: (724) 222-6420
www.westpenn-wpw.com
Standard Lengths are 1000ft.

The Jacket is sequentially footmarked.

This document is the property of West Penn Wire.

The information contained herein is considered
Proprietary and not to be reproduced by any means
Without written consent of West Penn Wire
LISTING No.: 7161-0859:0101
CATEGORY: 7161 - CABLES-FIRE PROTECTIVE SIGNALING
LISTEE: West Penn Wire 2200 U.S. Highway 27 South, Richmond, IN, 47374 Contact: Dorna, Gerald (765) 994-9963
Email: [email protected]
DESIGN:

Types FPL and FPLP power limited fire protective signaling cable. Refer to listee's data sheet for detailed product description and operational considerations.

RATING:

INSTALLATION:

In accordance with listee's printed installation instructions, NEC Article 760, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction.

MARKING:

Listee's name, type, NEC rating and UL label.

APPROVAL:

Listed as power-limited fire protective signaling cable.

NOTES:

Date Issued: 05/03/2024 Listing Expires: 06/30/2025
Authorized By: David Castillo, Program Coordinator
Fire Engineering & Investigations Division
Rev. 12-15-23 bh

Page 1 of 1 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE
LISTING No.: 7160-0859:0102
CATEGORY: 7160 - CABLES-OTHERS
LISTEE: West Penn Wire 2200 U.S. Highway 27 South, Richmond, IN, 47374 Contact: Dorna, Gerald (765) 994-9963
Email: [email protected]
DESIGN:

Type NPLF conductor cable. Refer to listee's data sheet for detailed product description and operational considerations.

RATING:

INSTALLATION:

In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction.

MARKING:

Listee's name, type, NEC rating and UL label.

APPROVAL:

Listed as non-power limited conductor cable.

NOTES:

Date Issued: 05/03/2024 Listing Expires: 06/30/2025
Authorized By: David Castillo, Program Coordinator
Fire Engineering & Investigations Division
Rev. 12-15-2023
bh

Page 1 of 1 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE
LISTING No.: 7160-0859:0103
CATEGORY: 7160 - CABLES-OTHERS
LISTEE: West Penn Wire 2200 U.S. Highway 27 South, Richmond, IN, 47374 Contact: Dorna, Gerald (765) 994-9963
Email: [email protected]
DESIGN:

Type NPLFP plenum cable. Refer to listee's data sheet for detailed product description and operational considerations.

RATING:

INSTALLATION:

In accordance with listee's printed installation instructions, applicable codes and ordinances and in a manner acceptable to the authority having jurisdiction.

MARKING:

Type and UL label.

APPROVAL:

Listed as non power-limited plenum cable.

NOTES:

Date Issued: 05/03/2024 Listing Expires: 06/30/2025
Authorized By: David Castillo, Program Coordinator
Fire Engineering & Investigations Division
Rev. 12-15-2023
bh

Page 1 of 1 ends

CALIFORNIA DEPARTMENT OF FORESTRY & FIRE PROTECTION

OFFICE OF THE STATE FIRE MARSHAL

FIRE ENGINEERING & INVESTIGATIONS DIVISION

BUILDING MATERIALS LISTING PROGRAM

LISTING SERVICE
Activity ID Activity Name Original
Duration
Start Finish
Martin Luther King Jr Library Renovation - B05H - 12.08.24Martin Luther King Jr Library Renovation - B05H - 12.08.24 658 10-3-23 A 5-18-26 RFP TimelineRFP Timeline 31 10-3-23 A 1-18-24 A
RFP-1000 Swinerton to Submit Proposal 0 10-3-23 A
RFP-1020 COS Review Proposal and Select Design-Assist Contractor 31 10-4-23 A 12-5-23 A RFP-1050 Interview 0 12-6-23 A
RFP-1030 Notification of Award 0 12-7-23 A
RFP-1060 Preconstruction Notice to Proceed 0 1-18-24 A
Project Summary & MilestonesProject Summary & Milestones 611 1-18-24 A 5-18-26 Summary DurationsSummary Durations 611 1-18-24 A 5-18-26 SUM-100 Preconstruction Duration 212 1-18-24 A 2-14-25
SUM-140 Last day open to the public 0 12-28-24*
SUM-150 Last day branch staff will be in the building 0 1-15-25* SUM-160 Last day SPL support services w ill be in the building 0 2-15-25* SUM-130 Construction Duration 294 2-18-25 4-20-26
MIL-1000 Construction Start 0 2-18-25
SUM-120 Submittals Durations 139 3-4-25 9-17-25
MIL-1020 Grant Funding Deadline (March 2026) 0 3-31-26* MIL-1010 Substantial Completion 0 4-20-26
MIL-1030 Final Completion 0 5-18-26
MLK Jr. Closure MilestonesMLK Jr. Closure Milestones 0
PreconstructionPreconstruction 354 11-6-23 A 3-3-25
DesignDesign 325 11-6-23 A 1-17-25
Schematic DesignSchematic Design 178 11-6-23 A 3-12-24 A DSN-1000 Pre-Design 35 11-6-23 A 12-29-23 A
DSN-1010 Concept / Schematic Design 50 1-2-24 A 3-12-24 A Design DocumentsDesign Documents 60 3-13-24 A 7-31-24 A DSN-1040 Received 100% Design Development Docs. 60 3-13-24 A 6-13-24 A DSN-1060 Design-Assist Review - (DDs) 20 6-14-24 A 7-31-24 A Construction DocumentsConstruction Documents 134 6-14-24 A 1-17-25 DSN-1070 G4 Prepare & Submit 90% CDs 40 6-14-24 A 8-30-24 A DSN-1080 Design Assist & Constructibility Review - CDs 20 8-30-24 A 9-30-24 A DSN-1160 City Plan Check #1 20 8-30-24 A 10-15-24 A
DSN-1150 Architect Back Check #1 15 10-16-24 A 10-30-24 A DSN-1140 Submit 95% CDs 1 10-31-24 A 10-31-24 A
DSN-1130 City Plan Check #2 10 11-1-24 A 11-22-24 A
DSN-1110 Architect Back Check #2 15 11-25-24 A 12-9-24 A DSN-1200 Submit Permit Package #2 1 12-9-24 A 12-9-24 A S Oct N D J F M A M J Jul A S Oct N D J F M Apr M J Jul A S Oct N D J F M A M J Jul A S Oct N D J F 2024 2025 2026 2027
Swinerton to Submit Proposal
COS Review Proposal and Select Design-Assist Contractor Interview
Notification of A ward
Preconstruction Notice to Proceed
Preconstruction Duration
Last day open to the public
Last day branch staff will be in the building
Last day SPL support services w ill be in the building Construction Duration
Construction Start
Submittals Durations
Grant Funding Deadline (March 2026)
Substantial Completion
Final Completion
Pre-Design
Concept / Schematic Design
Received 100% Design Development Docs.

Design-Assist Review - (DDs)
G4 Prepare & Submit 90% CDs
Design Assist & Constructibility Review - CDs
City Plan Check #1
Architect Back Check #1
Submit 95% CDs
City Plan Check #2
Architect Back Check #2
Submit Permit Package #2
Martin Luther King Jr Library Renovation - B05H - 12.08.24

1. GMP Proposal Schedule
Data Date: 12-8-24
Remaining Level of Effort
Actual Level of Effort
Actual Work
Remaining Work
Critical Remaining Work
Milestone

Page 1 of 9 ends

Activity ID Activity Name Original
Duration
Start Finish
DSN-1170 City Plan Check #3 10 12-10-24 A 12-23-24
DSN-1180 Architect Back Check #3 15 12-26-24 1-16-25
DSN-1190 Submit Permit Package #3 1 1-17-25 1-17-25
PermitsPermits 42 12-9-24 2-10-25
PER-1000 Demo & Abatement Permit (90% CDs) 15 12-9-24 12-31-24 PER-1010 COS Issue Permit 15 1-21-25 2-10-25
Trade Buyout & GMPTrade Buyout & GMP 118 9-3-24 A 3-3-25 BUY -130 Subcontractor Bidding & Finalize Scopes 20 9-3-24 A 9-20-24 A BUY -110 Bid Leveling 10 9-23-24 A 10-4-24 A
BUY -170 Prepare GMP 10 10-7-24 A 12-16-24
BUY -210 Finalize & Submit GMP - ( Plan Check #2 Comments ) 5 12-10-24 12-16-24 BUY -200 COS Review GMP f or City Council Approval 25 12-17-24 1-24-25 BUY -220 City Council Review & Approve GMP 15 1-27-25 2-14-25 BUY -190 COS Issue NTP 0 2-14-25
BUY -180 Swinerton Issue Subcontractor W ork Orders 10 2-18-25 3-3-25 Submittals & ProcurementSubmittals & Procurement 241 8-26-24 A 9-17-25 Electrical SwitchboardElectrical Switchboard 234 8-26-24 A 9-17-25 SUB-740 Electrical Switchgear Procurement (by Owner) 234 8-26-24 A 9-17-25 Remianing Electrical EquipmentRemianing Electrical Equipment 105 3-4-25 7-30-25 SUB-760 Prepare & Submit Shop Drawings - Electrical Equipment 20 3-4-25 3-31-25 SUB-810 Swinerton Review - Electrical Equipment 5 4-1-25 4-7-25 SUB-770 Design Team Review Shop Drawings - Electrical Equipment 10 4-8-25 4-21-25 SUB-780 Revise & Resubmit Shop Drawings - Electrical Equipment 5 4-22-25 4-28-25 SUB-790 Design Team Approve Revised Shop Drawings - Electrical Equipment5 4-29-25 5-5-25 SUB-800 Fabricate & Deliver - Electrical Equipment 60 5-6-25 7-30-25 VRF SystemVRF System 105 3-4-25 7-30-25
SUB-100 Prepare & Submit Shop Drawings - VRF System 20 3-4-25 3-31-25 SUB-210 Swinerton Review - VRF System 5 4-1-25 4-7-25
SUB-320 Design Team Review Shop Drawings - VRF System 10 4-8-25 4-21-25 SUB-430 Revise & Resubmit Shop Drawings - VRF System 5 4-22-25 4-28-25 SUB-540 Design Team Approve Revised Shop Drawings - VRF System 5 4-29-25 5-5-25 SUB-650 Fabricate & Deliver - VRF System 60 5-6-25 7-30-25 LightingLighting 105 3-4-25 7-30-25
SUB-140 Prepare & Submit Shop Drawings - Lighting 20 3-4-25 3-31-25 SUB-250 Swinerton Review - Lighting 5 4-1-25 4-7-25
SUB-360 Design Team Review Shop Drawings - Lighting 10 4-8-25 4-21-25 SUB-470 Revise & Resubmit Shop Drawings - Lighting 5 4-22-25 4-28-25 S Oct N D J F M A M J Jul A S Oct N D J F M Apr M J Jul A S Oct N D J F M A M J Jul A S Oct N D J F 2024 2025 2026 2027
City Plan Check #3
Architect Back Check #3
Submit Permit Package #3
Demo & Abatement Permit (90% CDs)
COS Issue Permit
Subcontractor Bidding & Finalize Scopes
Bid Leveling
Prepare GMP
Finalize & Submit GMP - ( Plan Check #2 Comments )
COS Review GMP f or City Council Approval
City Council Review & Approve GMP
COS Issue NTP
Swinerton Issue Subcontractor W ork Orders
Electrical Switchgear Procurement (by Owner)
Prepare & Submit Shop Drawings - Electrical Equipment
Swinerton Review - Electrical Equipment
Design Team Review Shop Drawings - Electrical Equipment Revise & Resubmit Shop Drawings - Electrical Equipment
Design Team Approve Revised Shop Drawings - Electrical Equipment Fabricate & Deliver - Electrical Equipment
Prepare & Submit Shop Drawings - VRF System
Swinerton Review - VRF System
Design Team Review Shop Drawings - VRF System
Revise & Resubmit Shop Drawings - VRF System
Design Team Approve Revised Shop Drawings - VRF System
Fabricate & Deliver - VRF System
Prepare & Submit Shop Drawings - Lighting
Swinerton Review - Lighting
Design Team Review Shop Drawings - Lighting
Revise & Resubmit Shop Drawings - Lighting
Martin Luther King Jr Library Renovation - B05H - 12.08.24

1. GMP Proposal Schedule
Data Date: 12-8-24
Remaining Level of Effort
Actual Level of Effort
Actual Work
Remaining Work
Critical Remaining Work
Milestone

Page 2 of 9 ends

Activity ID Activity Name Original
Duration
Start Finish
SUB-580 Design Team Approve Revised Shop Drawings - Lighting 5 4-29-25 5-5-25 SUB-690 Fabricate & Deliver - Lighting 60 5-6-25 7-30-25 FramesFrames 85 3-4-25 7-1-25
SUB-180 Prepare & Submit Shop Drawings - DFH 20 3-4-25 3-31-25 SUB-290 Swinerton Review - DFH 5 4-1-25 4-7-25
SUB-400 Design Team Review Shop Drawings - DFH 10 4-8-25 4-21-25 SUB-510 Revise & Resubmit Shop Drawings - DFH 5 4-22-25 4-28-25 SUB-620 Design Team Approve Revised Shop Drawings - DFH 5 4-29-25 5-5-25 SUB-730 Fabricate & Deliver - DFH 40 5-6-25 7-1-25
Doors & HardwareDoors & Hardware 85 3-4-25 7-1-25
SUB-820 Prepare & Submit Shop Drawings - DFH 20 3-4-25 3-31-25 SUB-870 Swinerton Review - DFH 5 4-1-25 4-7-25
SUB-830 Design Team Review Shop Drawings - DFH 10 4-8-25 4-21-25 SUB-840 Revise & Resubmit Shop Drawings - DFH 5 4-22-25 4-28-25 SUB-850 Design Team Approve Revised Shop Drawings - DFH 5 4-29-25 5-5-25 SUB-860 Fabricate & Deliver - DFH 40 5-6-25 7-1-25
Wood Slat CeilingsWood Slat Ceilings 105 3-4-25 7-30-25 SUB-130 Prepare & Submit Shop Drawings - W ood Slat Ceilings 20 3-4-25 3-31-25 SUB-240 Swinerton Review - Wood Slat Ceilings 5 4-1-25 4-7-25 SUB-350 Design Team Review Shop Drawings - Wood Slat Ceilings 10 4-8-25 4-21-25 SUB-460 Revise & Resubmit Shop Drawings - W ood Slat Ceilings 5 4-22-25 4-28-25 SUB-570 Design Team Approve Revised Shop Drawings - Wood Slat Ceilings5 4-29-25 5-5-25 SUB-680 Fabricate & Deliver - Wood Slat Ceilings 60 5-6-25 7-30-25 WindowsWindows 125 3-4-25 8-27-25
SUB-150 Prepare & Submit Shop Drawings - Windows 20 3-4-25 3-31-25 SUB-260 Swinerton Review - Windows 5 4-1-25 4-7-25
SUB-370 Design Team Review Shop Drawings - Windows 10 4-8-25 4-21-25 SUB-480 Revise & Resubmit Shop Drawings - Windows 5 4-22-25 4-28-25 SUB-590 Design Team Approve Revised Shop Drawings - Windows 5 4-29-25 5-5-25 SUB-700 Fabricate & Deliver - Windows 80 5-6-25 8-27-25 StorefrontStorefront 125 3-4-25 8-27-25
SUB-110 Prepare & Submit Shop Drawings - Storefront 20 3-4-25 3-31-25 SUB-220 Swinerton Review - Storefront 5 4-1-25 4-7-25
SUB-330 Design Team Review Shop Drawings - Storefront 10 4-8-25 4-21-25 SUB-440 Revise & Resubmit Shop Drawings - Storefornt 5 4-22-25 4-28-25 SUB-550 Design Team Approve Revised Shop Drawings - Storefront 5 4-29-25 5-5-25 SUB-660 Fabricate & Deliver - Storefront 80 5-6-25 8-27-25 S Oct N D J F M A M J Jul A S Oct N D J F M Apr M J Jul A S Oct N D J F M A M J Jul A S Oct N D J F 2024 2025 2026 2027
Design Team Approve Revised Shop Drawings - Lighting
Fabricate & Deliver - Lighting
Prepare & Submit Shop Drawings - DFH
Swinerton Review - DFH
Design Team Review Shop Drawings - DFH
Revise & Resubmit Shop Drawings - DFH
Design Team Approve Revised Shop Drawings - DFH
Fabricate & Deliver - DFH
Prepare & Submit Shop Drawings - DFH
Swinerton Review - DFH
Design Team Review Shop Drawings - DFH
Revise & Resubmit Shop Drawings - DFH
Design Team Approve Revised Shop Drawings - DFH
Fabricate & Deliver - DFH
Prepare & Submit Shop Drawings - W ood Slat Ceilings
Swinerton Review - Wood Slat Ceilings
Design Team Review Shop Drawings - Wood Slat Ceilings
Revise & Resubmit Shop Drawings - W ood Slat Ceilings
Design Team Approve Revised Shop Drawings - Wood Slat Ceilings Fabricate & Deliver - Wood Slat Ceilings
Prepare & Submit Shop Drawings - Windows
Swinerton Review - Windows
Design Team Review Shop Drawings - Windows
Revise & Resubmit Shop Drawings - Windows
Design Team Approve Revised Shop Drawings - Windows
Fabricate & Deliver - Windows
Prepare & Submit Shop Drawings - Storefront
Swinerton Review - Storefront
Design Team Review Shop Drawings - Storefront
Revise & Resubmit Shop Drawings - Storefornt
Design Team Approve Revised Shop Drawings - Storefront
Fabricate & Deliver - Storefront
Martin Luther King Jr Library Renovation - B05H - 12.08.24

1. GMP Proposal Schedule
Data Date: 12-8-24
Remaining Level of Effort
Actual Level of Effort
Actual Work
Remaining Work
Critical Remaining Work
Milestone

Page 3 of 9 ends

Activity ID Activity Name Original
Duration
Start Finish
ACT CeilingsACT Ceilings 105 3-4-25 7-30-25
SUB-170 Prepare & Submit Shop Drawings - ACT Ceilings 20 3-4-25 3-31-25 SUB-280 Swinerton Review - ACT Ceilings 5 4-1-25 4-7-25 SUB-390 Design Team Review Shop Drawings - ACT Ceilings 10 4-8-25 4-21-25 SUB-500 Revise & Resubmit Shop Drawings - ACT Ceilings 5 4-22-25 4-28-25 SUB-610 Design Team Approve Revised Shop Drawings - ACT Ceilings 5 4-29-25 5-5-25 SUB-720 Fabricate & Deliver - ACT Ceilings 60 5-6-25 7-30-25 Bathroom PartitionsBathroom Partitions 95 3-4-25 7-16-25 SUB-200 Prepare & Submit Shop Drawings - Bathroom Partitions 20 3-4-25 3-31-25 SUB-310 Swinerton Review - Bathroom Partitions 5 4-1-25 4-7-25 SUB-420 Design Team Review Shop Drawings - Bathroom Partitions 10 4-8-25 4-21-25 SUB-530 Revise & Resubmit Shop Drawings - Bathroom Partitions 5 4-22-25 4-28-25 SUB-640 Design Team Approve Revised Shop Drawings - Bathroom Partitions5 4-29-25 5-5-25 SUB-750 Fabricate & Deliver - Bathroom Partitions 50 5-6-25 7-16-25 SteelSteel 75 3-4-25 6-17-25
SUB-120 Prepare & Submit Shop Drawings - Steel 20 3-4-25 3-31-25 SUB-230 Swinerton Review - Steel 5 4-1-25 4-7-25
SUB-340 Design Team Review Shop Drawings - Steel 10 4-8-25 4-21-25 SUB-450 Revise & Resubmit Shop Drawings - Steel 5 4-22-25 4-28-25 SUB-560 Design Team Approve Revised Shop Drawings - Steel 5 4-29-25 5-5-25 SUB-670 Fabricate & Deliver - Steel 30 5-6-25 6-17-25
ConstructionConstruction 314 2-18-25 5-18-26
MobilizeMobilize 8 2-18-25 2-27-25
CON-MOB-100 Mobilize & Setup Temperaries (W ater & Temp Power) 5 2-18-25 2-24-25 CON-MOB-110 Relocate Library Books & Furniture (Owner) 5 2-18-25 2-24-25 CON-MOB-120 Protect & Store Whipser Box 2 2-20-25 2-21-25 CON-MOB-130 Safe-off 3 2-25-25 2-27-25
CON-MOB-140 Install Plywood Sub-floor Overlay 2 2-25-25 2-26-25 DemolitionDemolition 44 2-25-25 4-25-25
BasementBasement 38 2-25-25 4-17-25
CON-DEMO-100 Basement Temp. Hoist System (Equipment Demo & Install) 3 2-25-25 2-27-25 CON-DEMO-110 Abatement 20 2-28-25 3-27-25
CON-DEMO-140 Demo Plumbing 5 3-28-25 4-3-25
CON-DEMO-160 Demo Electrical 10 3-28-25 4-10-25
CON-DEMO-170 Demo Mechanical 15 3-28-25 4-17-25
First FloorFirst Floor 21 3-28-25 4-25-25
CON-DEMO-120 1st Floor W all & Ceiling Demo 20 3-28-25 4-24-25 S Oct N D J F M A M J Jul A S Oct N D J F M Apr M J Jul A S Oct N D J F M A M J Jul A S Oct N D J F 2024 2025 2026 2027
Prepare & Submit Shop Drawings - ACT Ceilings
Swinerton Review - ACT Ceilings
Design Team Review Shop Drawings - ACT Ceilings
Revise & Resubmit Shop Drawings - ACT Ceilings
Design Team Approve Revised Shop Drawings - ACT Ceilings Fabricate & Deliver - ACT Ceilings
Prepare & Submit Shop Drawings - Bathroom Partitions
Swinerton Review - Bathroom Partitions
Design Team Review Shop Drawings - Bathroom Partitions
Revise & Resubmit Shop Drawings - Bathroom Partitions
Design Team Approve Revised Shop Drawings - Bathroom Partitions Fabricate & Deliver - Bathroom Partitions
Prepare & Submit Shop Drawings - Steel
Swinerton Review - Steel
Design Team Review Shop Drawings - Steel
Revise & Resubmit Shop Drawings - Steel
Design Team Approve Revised Shop Drawings - Steel
Fabricate & Deliver - Steel
Mobilize & Setup Temperaries (W ater & Temp Power)
Relocate Library Books & Furniture (Owner)
Protect & Store Whipser Box
Safe-off
Install Plywood Sub-floor Overlay
Basement Temp. Hoist System (Equipment Demo & Install)
Abatement
Demo Plumbing
Demo Electrical
Demo Mechanical
1st Floor W all & Ceiling Demo
Martin Luther King Jr Library Renovation - B05H - 12.08.24

1. GMP Proposal Schedule
Data Date: 12-8-24
Remaining Level of Effort
Actual Level of Effort
Actual Work
Remaining Work
Critical Remaining Work
Milestone

Page 4 of 9 ends

Activity ID Activity Name Original
Duration
Start Finish
CON-DEMO-180 Demo Flooring 5 4-4-25 4-10-25
CON-DEMO-200 Demo Interior for Shoring 5 4-4-25 4-10-25 CON-DEMO-210 Shoring 5 4-14-25 4-18-25
CON-DEMO-220 Demo BRG W alls 5 4-21-25 4-25-25
ExteriorExterior 10 3-28-25 4-10-25
CON-DEMO-130 Demo (E) Y ard MEP Equipment 10 3-28-25 4-10-25 CON-DEMO-150 Demo Exterior Sidewalk & Patio 5 3-28-25 4-3-25 CON-DEMO-190 Cap City W ater Tie-in 5 4-4-25 4-10-25
Structural UpgradesStructural Upgrades 79 3-28-25 7-18-25 BasementBasement 52 3-28-25 6-10-25
CON-S-100 Repair W ater Intr usion Is sues - Basement 5 3-28-25 4-3-25 CON-S-190 Repair W ater Intr usion Is sues - Cr awl Space 20 4-18-25 5-15-25 CON-S-110 Footing Layout 1 4-28-25 4-28-25
CON-S-170 Saw Cut & Demo Concrete for New Footings 2 4-29-25 4-30-25 CON-S-180 Footing Excavation 3 5-1-25 5-5-25
CON-S-200 Footing Rebar 1 5-6-25 5-6-25
CON-S-210 Anchor Bolts 1 5-7-25 5-7-25
CON-S-220 Place Concrete Footings 1 5-8-25 5-8-25
CON-S-130 Crawl Space Drywall & Taping 10 5-28-25 6-10-25 First FloorFirst Floor 66 4-11-25 7-15-25
CON-S-160 Remove Plywood Sub-floor (Structural Upgrades & Footings) 5 4-11-25 4-17-25 CON-S-430 Mechanical Penetrations Layout 3 4-11-25 4-15-25 CON-S-150 Frame Mechanical Floor Penetrations 10 4-16-25 4-29-25 CON-S-420 Stem W all HDU's 12 4-18-25 5-5-25
CON-S-390 Sub-floor Blocking & Sheathing 15 5-6-25 5-27-25 CON-S-410 Sub-floor Straps 10 5-6-25 5-19-25
CON-S-370 Shear W all Framing 10 5-20-25 6-3-25
CON-S-330 Install HSS Columns 2 6-18-25 6-19-25
CON-S-350 Jamb Post & Beam Install (Roll-up Door) 5 6-18-25 6-24-25 CON-S-440 W8 W ood Nailer s 2 6-18-25 6-19-25
CON-S-450 W8 Beam Install 5 6-20-25 6-26-25
CON-S-340 Grout Columns 3 6-27-25 7-1-25
CON-S-380 Infill Sub-floor Framing at Steel Columns 5 7-9-25 7-15-25 RoofRoof 42 5-20-25 7-18-25
CON-S-500 Roof Level Straps 10 5-20-25 6-3-25
CON-S-480 Roof HDU's 15 5-28-25 6-17-25
CON-S-510 Diagonal Kickers 10 5-28-25 6-10-25
CON-S-520 Low & High Soffit Wood Framing 12 6-18-25 7-3-25 S Oct N D J F M A M J Jul A S Oct N D J F M Apr M J Jul A S Oct N D J F M A M J Jul A S Oct N D J F 2024 2025 2026 2027
Demo Flooring
Demo Interior for Shoring
Shoring
Demo BRG W alls
Demo (E) Y ard MEP Equipment
Demo Exterior Sidewalk & Patio
Cap City W ater Tie-in
Repair W ater Intr usion Is sues - Basement
Repair W ater Intr usion Is sues - Cr awl Space
Footing Layout
Saw Cut & Demo Concrete for New Footings
Footing Excavation
Footing Rebar
Anchor Bolts
Place Concrete Footings
Crawl Space Drywall & Taping
Remove Plywood Sub-floor (Structural Upgrades & Footings) Mechanical Penetrations Layout
Frame Mechanical Floor Penetrations
Stem W all HDU' s
Sub-floor Blocking & Sheathing
Sub-floor Straps
Shear W all Framing
Install HSS Columns
Jamb Post & Beam Install (Roll-up Door)
W8 W ood Nailer s
W8 Beam Install
Grout Columns
Infill Sub-floor Framing at Steel Columns
Roof Level Straps
Roof HDU's
Diagonal Kickers
Low & High Soffit Wood Framing
Martin Luther King Jr Library Renovation - B05H - 12.08.24

1. GMP Proposal Schedule
Data Date: 12-8-24
Remaining Level of Effort
Actual Level of Effort
Actual Work
Remaining Work
Critical Remaining Work
Milestone

Page 5 of 9 ends

Activity ID Activity Name Original
Duration
Start Finish
CON-S-460 Roof Joist Framing to W8 Beams 5 6-27-25 7-3-25 CON-S-470 Remove Scaffolding 2 7-7-25 7-8-25
CON-S-490 Top of W all Blocking 10 7-7-25 7-18-25
CON-S-530 MEPF Supports 10 7-7-25 7-18-25
Basement MEPFBasement MEPF 40 6-11-25 8-6-25
BasementBasement 40 6-11-25 8-6-25
CON-S-320 (N) Plumbing Install - DW & SS 15 6-11-25 7-1-25 CON-S-250 (N) Electrical Install 20 6-11-25 7-9-25
CON-S-240 (N) Mechanical Install 25 7-2-25 8-6-25
First FloorFirst Floor 0
RoofRoof 0
ExteriorExterior 127 4-11-25 10-9-25
BuildingBuilding 127 4-11-25 10-9-25
CON-EXT-1040 Install Site Utilities 15 4-11-25 5-1-25
CON-EXT-1030 Repair Damaged Fascia & Soffits 15 7-21-25 8-8-25 CON-EXT-1050 Exterior CMU Wor k 5 7-21-25 7-25-25
CON-EXT-1110 South Elevation Fiber Cement Board & Batten 12 8-11-25 8-26-25 CON-EXT-1070 South Window R&R 5 8-28-25 9-4-25
CON-EXT-1080 East Doors & Windows R&R 5 9-5-25 9-11-25
CON-EXT-1090 North Doors & Windows R&R 5 9-12-25 9-18-25 CON-EXT-1100 West Doors & Windows R&R 5 9-19-25 9-25-25 CON-EXT-1060 Water T esting Windows & Doors 5 9-26-25 10-2-25 CON-EXT-1120 Paint 5 10-3-25 10-9-25
Mechanical YardMechanical Yard 64 7-10-25 10-8-25
CON-INT-1770 Pull Feeders 10 7-10-25 7-23-25
CON-INT-1570 VRF & Mechanical Y ard Buildout 25 7-31-25 9-4-25 CON-INT-1630 Set (N) Switchboard & Land Wire 5 10-2-25 10-8-25 Interior BuildoutInterior Buildout 180 7-21-25 4-9-26
CON-S-400 Self Leveling Floor Overlay 5 9-4-25 9-10-25
Restrooms / Wellness / Janitors ClosetRestrooms / Wellness / Janitors Closet 91 7-21-25 11-25-25 CON-INT-1650 Metal Stud Framing 15 7-21-25 8-8-25
CON-INT-1000 MEPF Rough-in 10 9-11-25 9-24-25
CON-INT-1710 A V / Security Install 10 9-25-25 10-8-25
CON-INT-1010 Insulation & Drywall 3 10-9-25 10-13-25
CON-INT-1040 Taping 7 10-14-25 10-22-25
CON-INT-1110 Door Frames 1 10-23-25 10-23-25
CON-INT-1120 Paint 3 10-24-25 10-28-25
CON-INT-1140 Tile 10 10-29-25 11-11-25
S Oct N D J F M A M J Jul A S Oct N D J F M Apr M J Jul A S Oct N D J F M A M J Jul A S Oct N D J F 2024 2025 2026 2027
Roof Joist Framing to W8 Beams
Remove Scaffolding
Top of W all Blocking
MEPF Supports
(N) Plumbing Install - DW & SS
(N) Electrical Install
(N) Mechanical Install
Install Site Utilities
Repair Damaged Fascia & Soffits
Exterior CMU Wor k
South Elevation Fiber Cement Board & Batten
South Window R&R
East Doors & Windows R&R
North Doors & Windows R&R
West Doors & Windows R&R
Water T esting Windows & Doors
Paint
Pull Feeders
VRF & Mechanical Y ard Buildout
Set (N) Switchboard & Land Wire
Self Leveling Floor Overlay
Metal Stud Framing
MEPF Rough-in
A V / Security Install
Insulation & Drywall
Taping
Door Frames
Paint
Tile
Martin Luther King Jr Library Renovation - B05H - 12.08.24

1. GMP Proposal Schedule
Data Date: 12-8-24
Remaining Level of Effort
Actual Level of Effort
Actual Work
Remaining Work
Critical Remaining Work
Milestone

Page 6 of 9 ends

Activity ID Activity Name Original
Duration
Start Finish
CON-INT-1230 Doors & Hardware 2 11-12-25 11-13-25
CON-INT-1240 V anities 2 11-12-25 11-13-25
CON-INT-1430 Lighting & Final Trim Out 3 11-14-25 11-18-25 CON-INT-1260 Plumbing Fixtures 5 11-14-25 11-20-25
CON-INT-1320 Bathroom Partitions & Accesaries 3 11-21-25 11-25-25 Staff SpacesStaff Spaces 131 7-30-25 2-9-26
CON-INT-1660 Metal Stud Framing 12 7-30-25 8-14-25
CON-INT-1640 Make Up (N) Electrical Panels 15 9-11-25 10-1-25 CON-INT-1030 MEPF Rough-in 15 9-25-25 10-15-25
CON-INT-1060 Insulation & Drywall 3 10-16-25 10-20-25
CON-INT-1070 IT Room Build-Out 25 10-16-25 11-19-25
CON-INT-1100 Taping 10 10-21-25 11-3-25
CON-INT-1150 Door Frames 3 11-4-25 11-6-25
CON-INT-1180 Paint 5 11-7-25 11-13-25
CON-INT-1720 Build-out A V Room 15 11-7-25 12-1-25
CON-INT-1200 ACT Grid 5 11-14-25 11-20-25
CON-INT-1210 Casework 3 11-14-25 11-18-25
CON-INT-1220 Bathroom Tile 5 11-14-25 11-20-25
CON-INT-1270 Above Ceiling Rough-in 10 11-21-25 12-8-25 CON-INT-1280 Breakroom / Restroom Fixtures 2 11-21-25 11-24-25 CON-INT-1700 A V / Security Install 10 12-9-25 12-22-25 CON-INT-1360 Drop Ceiling Tiles 5 12-23-25 12-31-25
CON-INT-1390 Flooring & Base 5 1-5-26 1-9-26
CON-INT-1410 Doors & Hardware 3 1-12-26 1-14-26
CON-INT-1420 AMHS Install 5 1-12-26 1-16-26
CON-INT-1440 Final Paint 5 1-15-26 1-22-26
CON-INT-1470 Lighting & Final Trim Out 10 1-23-26 2-5-26 CON-INT-1480 Cubicles & Office Furniture 10 1-23-26 2-5-26 CON-INT-1520 Signage 2 2-6-26 2-9-26
Library AreasLibrary Areas 168 8-6-25 4-9-26
CON-INT-1670 Metal Stud Framing 10 8-6-25 8-19-25
CON-INT-1020 MEPF Rough-in 10 9-25-25 10-8-25
CON-INT-1050 Insulation & Drywall 10 10-9-25 10-22-25
CON-INT-1380 Lighting & Cloud Supports 12 10-9-25 10-24-25 CON-INT-1090 Taping 15 10-23-25 11-12-25
CON-INT-1170 Storefront & Door Frames 5 11-13-25 11-19-25 CON-INT-1190 Paint 10 11-20-25 12-5-25
CON-INT-1300 ACT Grid 15 12-8-25 12-30-25
S Oct N D J F M A M J Jul A S Oct N D J F M Apr M J Jul A S Oct N D J F M A M J Jul A S Oct N D J F 2024 2025 2026 2027
Doors & Hardware
V anities
Lighting & Final Trim Out
Plumbing Fixtures
Bathroom Partitions & Accesaries
Metal Stud Framing
Make Up (N) Electrical Panels
MEPF Rough-in
Insulation & Drywall
IT Room Build-Out
Taping
Door Frames
Paint
Build-out A V Room
ACT Grid
Casework
Bathroom Tile
Above Ceiling Rough-in
Breakroom / Restroom Fixtures
A V / Security Install
Drop Ceiling Tiles
Flooring & Base
Doors & Hardware
AMHS Install
Final Paint
Lighting & Final Trim Out
Cubicles & Office Furniture
Signage
Metal Stud Framing
MEPF Rough-in
Insulation & Drywall
Lighting & Cloud Supports
Taping
Storefront & Door Frames
Paint
ACT Grid
Martin Luther King Jr Library Renovation - B05H - 12.08.24

1. GMP Proposal Schedule
Data Date: 12-8-24
Remaining Level of Effort
Actual Level of Effort
Actual Work
Remaining Work
Critical Remaining Work
Milestone

Page 7 of 9 ends

Activity ID Activity Name Original
Duration
Start Finish
CON-INT-1690 A V / Security Install 10 12-22-25 1-8-26
CON-INT-1370 Above Ceiling Rough-in 15 12-31-25 1-23-26 CON-INT-1740 Lighting 15 12-31-25 1-23-26
CON-INT-1460 Drop Ceiling Tiles 10 1-26-26 2-6-26
CON-INT-1310 Wood Ceilings 15 1-26-26 2-13-26
CON-INT-1750 Direct Applied ACT 15 1-26-26 2-13-26
CON-INT-1500 Casework & Custom Circulation Desk 15 2-2-26 2-23-26 CON-INT-1540 Flooring & Base 10 2-24-26 3-9-26
CON-INT-1560 Doors & Hardware 5 3-10-26 3-16-26
CON-INT-1580 Final Paint 5 3-17-26 3-23-26
CON-INT-1590 Lighting & Final Trim Out 10 3-24-26 4-6-26 CON-INT-1600 Reinstall Whisper Box 2 3-24-26 3-25-26
CON-INT-1610 Signage 3 4-7-26 4-9-26
Community Meeting RoomCommunity Meeting Room 130 8-20-25 3-2-26 CON-INT-1760 Metal Stud Framing 10 8-20-25 9-3-25
CON-INT-1080 MEPF Rough-in 15 10-9-25 10-29-25
CON-INT-1130 Insulation & Drywall 5 10-30-25 11-5-25
CON-INT-1160 Taping 10 11-6-25 11-19-25
CON-INT-1250 Door Frames 3 11-20-25 11-24-25
CON-INT-1780 Install Roll-up Door 5 11-20-25 11-26-25
CON-INT-1290 Paint 5 12-1-25 12-5-25
CON-INT-1330 Above Ceiling Rough-in 10 12-8-25 12-19-25 CON-INT-1340 Casework 3 12-8-25 12-10-25
CON-INT-1350 Kitchen Fixtures 2 12-11-25 12-12-25
CON-INT-1680 A V / Security Install 10 12-22-25 1-8-26
CON-INT-1400 Wood Ceilings 10 1-9-26 1-23-26
CON-INT-1450 Flooring & Base 5 1-26-26 1-30-26
CON-INT-1490 Doors & Hardware 3 2-2-26 2-4-26
CON-INT-1510 Final Paint 5 2-5-26 2-11-26
CON-INT-1530 Lighting & Final Trim Out 10 2-12-26 2-26-26 CON-INT-1550 Signage 2 2-27-26 3-2-26
Basement (Mechanical Room)Basement (Mechanical Room) 15 9-5-25 9-25-25 CON-INT-1620 Fire Protection Main & Riser (Basement & Crawl Space) 15 9-5-25 9-25-25 Punch ListPunch List 48 3-3-26 5-7-26
PUNCH-1000 Final Clean & Swinerton Pre-Punch List 5 3-3-26 3-9-26 PUNCH-1010 Owner / Architect Punch List 2 4-10-26 4-13-26 PUNCH-1020 Owner / Architect Punch List Corrections 5 4-10-26 4-16-26 PUNCH-1030 FFE Install & Staff Move-in 15 4-17-26 5-7-26 S Oct N D J F M A M J Jul A S Oct N D J F M Apr M J Jul A S Oct N D J F M A M J Jul A S Oct N D J F 2024 2025 2026 2027
A V / Security Install
Above Ceiling Rough-in
Lighting
Drop Ceiling Tiles
Wood Ceilings
Direct Applied ACT
Casework & Custom Circulation Desk
Flooring & Base
Doors & Hardware
Final Paint
Lighting & Final Trim Out
Reinstall Whisper Box
Signage
Metal Stud Framing
MEPF Rough-in
Insulation & Drywall
Taping
Door Frames
Install Roll-up Door
Paint
Above Ceiling Rough-in
Casework
Kitchen Fixtures
A V / Security Install
Wood Ceilings
Flooring & Base
Doors & Hardware
Final Paint
Lighting & Final Trim Out
Signage
Fire Protection Main & Riser (Basement & Crawl Space)
Final Clean & Swinerton Pre-Punch List
Owner / Architect Punch List
Owner / Architect Punch List Corrections
FFE Install & Staff Move-in
Martin Luther King Jr Library Renovation - B05H - 12.08.24

1. GMP Proposal Schedule
Data Date: 12-8-24
Remaining Level of Effort
Actual Level of Effort
Actual Work
Remaining Work
Critical Remaining Work
Milestone

Page 8 of 9 ends

Activity ID Activity Name Original
Duration
Start Finish
Final Inspections & CommissioningFinal Inspections & Commissioning 130 10-9-25 4-20-26 FIN-1050 Green Tag 1 10-9-25 10-9-25
FIN-1060 Schedule SMUD Power Crews 15 10-10-25 10-30-25 FIN-1080 Permanent Power & Remove Temp Power 5 10-31-25 11-6-25 FIN-1030 Start-up Equipment 10 11-20-25 12-5-25
FIN-1070 Commissioning 15 3-17-26 4-6-26
FIN-1040 TAB Reports 15 3-27-26 4-16-26
FIN-1000 Fire Alarm & Fire Sprinkler Testing 5 4-7-26 4-13-26 FIN-1010 ADA & Final Inspections 5 4-14-26 4-20-26
FIN-1020 TCO 0 4-20-26
Post- ConstructionPost- Construction 20 4-21-26 5-18-26 POST-1000 Closeout 20 4-21-26 5-18-26
S Oct N D J F M A M J Jul A S Oct N D J F M Apr M J Jul A S Oct N D J F M A M J Jul A S Oct N D J F 2024 2025 2026 2027
Green Tag
Schedule SMUD Power Crews
Permanent Power & Remove Temp Power
Start-up Equipment
Commissioning
TAB Reports
Fire Alarm & Fire Sprinkler Testing
ADA & Final Inspections
TCO
Closeout
Martin Luther King Jr Library Renovation - B05H - 12.08.24

1. GMP Proposal Schedule
Data Date: 12-8-24
Remaining Level of Effort
Actual Level of Effort
Actual Work
Remaining Work
Critical Remaining Work
Milestone

Page 9 of 9 ends

Page 1 of 3 ends

RFI
No.

Subject Question RFI
Author
Answer
Co.

Date Response Status
Round 1:
1 Flooring vapor treatment Section 09 6423 calls for vapor treatment on the "basement" slab. We assume this spec applies only at the main floor areas with resilient directly on concrete. Please confirm.

Swin. G4 9/13/24 That is correct. Closed
2 Skylights Spec's include section 08 6213. We assume this is a holdover from DD's and skylights have been deleted. Please confirm.

Swin. G4 9/13/24 Skylights are no longer included in the project. Closed 3 Library shelving and book
stacks
Specs include sections 105613 and 11 5123. We assume shelf and stack systems are furnished and installed by the Owner, and specs are for coordination purposes only. Please confirm.

Swin. G4/
Owner
9/13/24 Library shelf and stack system are to be furnished and installed by the general contractor Closed 4 Alternate D-07 "Brown Act" Please clarify the specific AV systems and components that are to be included in this alternate (info not found in plans and specs).

Swin. G4 9/13/24
On request from the city last week we are moving this out of the base and into and Add alternate. Our A/V is prepareing documents that show the add alternate for Brown Act. Below is a brief summary of the equipment needed for the brown act:

1. Network accessible solid state video recorder\

2. Additional microphone(s) as needed for panel/commission membership/size

2. In the rack: additional programming, possible legistlative management encoder (e.g. Granicus), video distribution/transfer to closed captioning cloud service or other 3rd party post-production/distribution service providers Closed
5 Alternate A-02 AMH system The AMH is noted as "OFCI". Please confirm if installation of the AMH equipment should be included by Swinerton, or if the owner's equipment vendor will install the equipment. (if installation is by Swinerton, please provide product data for coordination purposes).

Swin. G4/
Owner
9/13/24
Confirm with Library. OFOI. Contracter to coordinate exterior wall penetration with equipment vendor.

Closed
6 Gyp-crete spec (1) Please provide a specification for the "Cementitious Self-Levelling Compound" (gyp- crete?) noted on typical floor section details. (2) provide thickness (ex. 4/A9.5-5) Swin. G4 9/13/24 1/2" thickness - Spec is included in division 03 30 00 Cast-in-Place Concrete - 2.04 Accessory Materials - D. Floor Leveling and Fill Materials
Closed
7 Anti-graffiti coating New Spec section 09 9623 calls for anti-graffiti coating on exterior stucco up to 10 feet. The library does not have any new or existing stucco. Please clarify. (Note - prior budgeting did not account for any exterior anti-graffiti coatings).

Swin. G4 9/13/24 No ani-graffiti coating included Closed 8 Floor beam straps Sheet S2.03 calls for "ST2212" straps at 6x12 beams. We assume this should be "ST2122" straps ("2212" not found). Please confirm
Swin. Buehler 9/13/24 Yes, the strap tag should be “ST2122”. We will correct that on the next issue. Closed 9 Alt A-04 - Board/batten
siding
Please provide a product spec the fiber cement product and system. Swin. G4 9/13/24 See new spec section 07 46 46 Closed 10 Alt A-04 - Board/batten
siding
We assume new board and batten will need to be finish painted. Please provide exterior painting spec. We also assume this will result in re-painting most, if not all adjacent exterior elements, except for brick/masonry and roof. (i.e., low roof soffit, entire fascia, upper roof soffits, etc). Please clarify this is the intent for the alternate pricing option.

Swin. G4 9/13/24 The alternate is to only replace the ground level siding (no clerestory) on the south facade, extents shown on 5/A8.0-1. associated trim will be replaced with fiber cement trim to match existing. no painting of soffit, fascia, or other trim is in the scope of this alternate. Fiber Cement Painting section added to 09 9100 - Painting 2.2 Exterior Pinting schedule, E. Fiber Cement Siding and Trim: waterborne 100% acrylic exterior finish: Number of coats per manufacturer

1.Primer: siding and trim factory primed, no additional primer. Prime and paint all cut edges

2.Finish: Exterior semigloss acrylic
Closed
11 Alt A-01 Metal Fence/patio Please provide a product spec for the Metal Fence, or provide details if a custom iron fence is intended. (A manufacturerd fence product will be more cost effective) Swin. G4 9/13/24 See new spec section 32 31 19 Closed
12 Alt A-01 Metal Fence/patio Please provide spec for the new concrete pavers and finish. As an alternative, consider going with placed concrete flatwork instead of pavers.

Swin. G4 9/13/24 Placed concrete flatwork instead of pavers is acceptable Closed 13 Plaster scope Specification include section 09 2400, however, no new plaster is found on architectural plans.

Please cofirm if any new plaster work is required.

Swin. G4 9/13/24 No plaster work Closed
14 Exterior doors Door 005 and 007 are missing on the Door Schedule (shown on window elevations with new storefront). Please provide door hardware info, and update on door schedule.

Swin. G4 9/13/24 Sheet up dated to show doors, see A2.6-1 Closed 15 AISC Certifications The Steel Specifcation requiers AISC Certified Shop and Erector. This will limit bidders.

Please revise to submit shop procedures for review etc.

Swin. Buehler 9/13/24 The requirement for AISC Certification can be waived provided shop procedures are submitted Closed 17 Epoxy Anchors A9.3-1 shows Angle attached to Brick wall at ICL - Tectum Study room. Structural needs to show and call out angle and anchor. Assume occurs at Room 117 as well. Assume Detail 1/S5.24SIM
Swin. Buehler 9/13/24 Drawings updated to show angle and anchor details, Yes, same in room 117. See A9.3-1. See 6/A9.3-2 for metal deck to wood stud wall connection
Closed
18 Round 2:
19 Epoxy Crack Repair Quantify the Cracks to be repaired with Epoxy Injection. Need to get LF and width (1/8", 1/4", etc.) Confirm that there are no cracks being epoxy injected in the crawl space.

Swin. Buehler 9/24/24 Addendum B. The cracks to be repaired are in the west wall of the basement, approximately 25 LF. There is no crack repair specified for the crawl space.

Closed
20 Fire Sprinklers THE MOST REMOTE CALCULATION AREA "HIGH ROOF" HAS A CALCULATION AREA SIZE OF 1573 SQ. FT.

NFPA 13, 2022 EDITION SECTION 19.2.3.2.4 SLOPED CEILINGS REQUIRES A 30% INCREASE IN THE REMOTE AREA IF THE ROOF SLOPE EXCEEDS 2/12 PITCH. THE HIGH ROOF SLOPE IS A 4/12 PITCH, THEREFORE IT APPEARS THE CALCULATION AREA SHOULD BE INCREASED. PLEASE CONFIRM.

Bidder FP Eng. 9/24/24 Addendum B. Increased hydraulic calculation area by 30% per NFPA 13. Closed Swinerton Builders
MKL Library - Preconstruction RFI Log
(Bid Documents: 90% CD Plans/Specs dated 8/29/2024)

Page 2 of 3 ends

RFI
No.

Subject Question RFI
Author
Answer
Co.

Date Response Status
Swinerton Builders
MKL Library - Preconstruction RFI Log
(Bid Documents: 90% CD Plans/Specs dated 8/29/2024)
21 Fire Sprinklers THE G4XLO 11.2K CONCEALED PENDENT SPRINKLER IS SHOWN TO BE INSTALLED AT THE 4/12 PITCHED SLOPED ROOF. PER THE RELIABLE LISTING DATA SHEET FOR THAT PARTICULAR SPRINKLER HEAD, IT IS ONLY LISTED FOR UP TO 2/12 SLOPED CEILINGS.

CAN YOU HAVE THE ENGINEER OF RECORD REVISE THE FIRE SPRINKLER DESIGN LAYOUT TO INCORPORATE THE PROPER HEAD LISTED FOR THIS SPACE? Bidder FP Eng. 9/24/24 Addendum B. The G4XLO 11.2K heads are no longer being used in the design. Now using Reliable G5 for all concealed pendent sprinklers.

Closed
22 Fire Sprinklers THE SPRINKLER SYMBOLS IN THE FIRE SPRINKLER HEAD LEGEND SHOWS ONE SYMBOL FOR 2 DIFFERENT TYPES OF SPRINKLER HEADS.

CAN YOU HAVE THE ENGINEER OF RECORD REVISE THE FIRE SPRINKLER DESIGN SO THAT THE TWO DIFFERENT HEAD TYPES HAVE TWO DIFFERENT SYMBOLS? THIS WILL HELP CLARIFY WHICH SPRINKLER HEAD WILL GO AT EACH LOCATION.

Bidder FP Eng. 9/24/24 Addendum B. Extended coverage sprinklers are no longer being speced for the project, so no revision to sprinkler symbol needed.

Closed
23 Electrical/AV There are no one lines included in the TA 90% CD drawings for audio visual and paging systems. It cannot be determined what the intended system design is for Community Meeting 102 and the Paging system from the floor plans and RCPs. Please provide a detailed system description or one-line documents for these systems.

Bidder Elec. Eng. 9/24/24 Addendum B. Please see revised TA201 Device Plan, and TA601 Reflected Ceiling Plan Delta “B”, 9/24/24; and TA701 (Digital Signage, Group Study, Teen), TA702 (Community Room 102), TA703 (Community Room with Brown Act Bid Alt), and TA704 (Public Address) single line diagrams, added as part of Delta “B”, 9/24/24.

Closed
24 Flooring and carpet
Please provide product specs for all carpet, resilient flooring, and resilient base flooring types.

Specs list manufacturers only.

Bidder G4 9/23/24 Addendum B. All carpet to be Interface - Night Lights collection. Resilient (R-1) - Shaw Contract - Grain Direct Glue.

Resilient (R-2) - Shaw Contract - 4350V Commingle, 50505 Iron. Resilient (R-3) - Interface - Textured Stone LVT A003, dark concrete A00310. See A4.1-1 for updated finish plan.

Closed
25 Crack Repair and
Waterproofing
Clarify if the Surface applied waterproofing in the crawl space is the Bituthene 4000 Membrane with no protection board required? Or do you want the Sikadur 31 Hi-Mod Gel, applied to interior of crawl space and also basement walls with the Sikadur 35 being the injection material? Clarify if the Epoxy Injection is to occur on both sides of wall as called out for on S1.02 which will require excavation on the exterior to accomplish.

Swin. G4 9/23/24 Addendum B. Regarding the epoxy injectio of cracks, refer to EPOXY INJETION CONCRETE CRACK REPAIR on sheet S1.03. At this time it is thought that injection from only the interior face of the wall is required.

Closed
26 Metal Lockers Provide location, quantity, and prodcut type for Staff Lockers referenced in Section 10 5113. Swin. G4 9/24/24 Addendum B. Lockers are not included in the project. Spec section 10 5113 removed. Closed 27 Missing Openings on Door
Schedule
Openings 007, 008 & 009 are missing on the Door Schedule. Please provide door hardware info, and update on door schedule.

Swin. G4 9/24/24 Addendum B. Door schedule updated, See A2.6-1. Hardware groups 22 and 23 added to door hardware spec. Closed 28 LEED Certification Please confirm the Library project is NOT seeking LEED certification. Note - Various specification sections refer to LEED criteria (examples: 087100, 095000, 220500) Swin. G4 9/242024 Addendum B. Library is not seeking LEED certification. Specs sections 08 7100, 09 5000, 22 0500 will be updated to remove LEED requirements.

Closed
29 Deductive Alt D-01 Exterior
Glazing Retrofit
Please provide detail to better understand what is needed for Deductive Alt D-01 Exterior Glazing Retrofit.

Swin. G4 9/24/24 Addendum B. For deductive Alt D-01. All existing exterior storefront to remain, U.N.O. New glazing retrofit system added to inside of existing exterior storefront, see A.8.0-1 for typical detail. Storefront E03 and E34 to be new storefront system per drawings.

Closed
30 Wall Demo A2.4-1 calls wall to remain but on A2.0-0 calls portion of wall on GL 3/ B-C to be demoed.

From our understanding the wall finishes will be removed, faming will stay with new openings made in the wall for the new staff areas.

Swin. G4 9/24/24 Addendum B. Framing to remain, wall finishes to be removed, and new openings created per plans. Closed 31 Room 119 STC rating Please confirm STC rating for door at room 119. Swin. G4 9/24/24 Addendum B. STC 40 Closed 32 Library soffit demo (topside) Top side of soffit in library has extensive damage to the drywall. This should be completely demoed. Should we reinstall drywall or leave drywall off to cut cost. Currently the demo drawings do not say to remove the drywall.

Swin. G4 9/24/24 Addendum B. Drywall removed on top side of soffit, see notes on A2.0-4. No finish on top side of soffit. Provide blocking for all utilities on top side of soffit. See A9.3-3 for typical.

Closed
33 Door frame Grout 2/A8.6-1 - Is grout necessary for HM door frames Swin. G4 9/24/24 Addendum B. Grout is not necessary for HM door frames Closed 34 Top Track Welding Per detail 6/A9.0-2 Can the top track welding be eliminated and use screws instead. Swin. G4 9/24/24 Addendum B. Yes, top track welding can be eliminated. See updated A9.0-2 and A9.0-3. See structural drawings for fastener details
Closed
35 Exterior soffit lighting Confirming that exterior lights and conduits (type E1/C) should be surface mounted, so as to minimize cutting and patching existing plaster soffits.

Swin. G4 9/24/24 Addendum B. Surface mounted conduit and exterior soffit lights, minimize distubing plaster soffits. Closed 36 Wood Floor joists Please confirm if Structural Note 7 under "Wood" on S1.02 is correct, noting that "Joists under and parallel to partitions shall be doubled and nailed together". If correct, please show on structural plan sheets the joists that need to be doubled up.

Swin. Buehler 9/24/24 Addendum B. New partition stud walls over existing floor joists do not require that the joists be doubled and nailed together.

This note will be deleted.

ClosedRound 3:
37 Opening Issues Opening 007 is missing the glass type or it should not be door type D. Opening 110 is door type J and opening 124 is door type E. Please advise what door type J & E are or change the door types.

Swin. G4 9/24/24 Addendum B. Door schedule updated, See A2.6-1. Closed 38 Plumbing 1. Please provide make and model for L-1

2. Please provide make, model, and basin size for SP-1

3. please provide make and model for MV-1
Bidder Plumb.

Eng.
9/24/24 Addendum B. Updated See sheet P4-0-1 Closed

Page 3 of 3 ends

RFI
No.

Subject Question RFI
Author
Answer
Co.

Date Response Status
Swinerton Builders
MKL Library - Preconstruction RFI Log
(Bid Documents: 90% CD Plans/Specs dated 8/29/2024)
39 Plumbing SK-1, 2, & 3 descriptions do not match what is shown on drawings floor plans and do not specify how many stations each sink is. these are generally high dollar sink depending on size, station number, and other factors. Please clarify sink type and locations.

Bidder Plumb.

Eng.
9/23/24 Addendum B. Updated See sheet P4-0-1 Closed
40 Restroom 105 Sink Pipe
Guards
Detail 2/A5.0-4 seems to show sink pipe giards under the sinks, but the drawings do not specify what they are. Please clarify if these sink pipe guards are part of the sinks or if they will be seprate millwork pieces. If they will be seprate millwork pieces, please prvide details, materials, finishes, etc.

Swin. G4 9/24/24 Addendum B. Sink pipe guards at public restrooms to be part of the sinks. Bases of design is Sloan AD-81000 and AD-82000 series. Sink guards to be laminated cabinet-style vertical enclosure from Sloan. See 4/A9.5-3 for other sink locations Closed
Round 4:
41 A/V Brown Act Are the new TA sheets the entirety of the “Brown Act” AV scope? And we are now excluding this from the base scope, and treating it as Alternate ADD price? (instead of Alt. deduct “D- 07”).

Swin. G4. SFMI 9/26/24 Yes, the Brown Act Scope is excluded from the base scope and will be Add Alternate A-05.

TA702 provides the functionality for the Community Room sans Brown Act capabilities (Base Bid).

TA703 provides the functionality for the Community Room with Brown Act capabilities (Bid Alt).

Either TA702 or TA703 will be used depending on whether Bid Alt is accepted (not both).

The Brown Act capabilities provided by TA703 that differ from TA702:

1. Second PTZ camera

2. (8) additional wireless gooseneck microphones

3. Network accessible solid state video/audio recorder/archiver/streamer

4. Integration of OFCI computer for teleconferencing/moderation/agenda/etc Closed
42 Finish Floor Plan
As per RFI 24-flooring and Carpet (1) resilient R-1 Floor is shaw contract but per specificiation section 09 65 00 resilient floorig is calling for forbo marmoleum linoleum sheet. Please confirm (2) RFI calls R-2 also as shaw contract floor but in finish plan R-2 is coved rubber base. (3) rfi also calls for R-3 resilient interface LVT, but in finish plan there is no R-3. Both old and updated sheet A4.1-1 are the same
Bidder G4 9/26/24 RFI 24 is correct. See drawing 1/A4.1-1 for resilient flooring locations, ignore base type marks. Flooring and Base Specification and type marks will be updated to match selections in the next addendum. Wall Base: ASTM F1861, Type TS (rubber, vulcanized thermoset).

1.Manufacturer: Armstrong World Industries, Inc.

2.Group (Manufacturing Method): I (solid, homogeneous).

3.Style:
a.At Hard Floor Surfaces: Cove (with top-set toe).
b.At Soft Floor Surfaces: Straight.

4.Minimum Thickness: 0.125-inch (3.2 mm).

5.Height: 4-inches (102 mm).

6.Lengths: Coils in manufacturer's standard length, but not less than 100 feet.

7.Outside Corners: Premolded.

8.Inside Corners: Premolded.

9.Surface: Smooth.

10.Color: Burke Accord 701 Black.

Closed

SUPPLEMENTAL CONTRACT
(Rev. 11-1-19)
Project Title and Job Number: Martin Luther King Jr. Library Remodel Design Services Date: 6/11/2024 Purchase Order #: 0000073940 Supplemental Contract No.: 3

The City of Sacramento ("City") and Group 4 Architecture, Research + Planning Inc. _("Contractor"), as parties to that certain Professional Services Agreement designated as Contract Number 2023-1466, including any and all prior supplemental contracts modifying the contract (the contract and all supplemental contracts are hereafter collectively referred to as the "Contract"), hereby supplement and modify the Contract as follows:

1. The Scope of Services specified in Exhibit A of the Contract is amended as follows:

Construction Administration and Close Out fee required to complete the project, as set forth in Attachment 3 to Exhibit A, attached hereto and incorporate by reference.

2. In consideration of the additional and/or revised services described in section 1, above, the maximum not -to-exceed amount that is specified in Exhibit B of the Contract for payment of Contractor's fees and expenses, is increased by $245,100.00, and the Contract’s maximum not-to-exceed amount is amended as follows:

Agreement's original not-to-exceed amount: $ 897,000.00 Net change by previous supplemental contracts: $ 40,352.00 Not-to-exceed amount prior to this supplemental contract: $ 937,352.00 Increase by this supplemental contract: $ 245,100.00
New not-to exceed amount including all supplemental contracts: $1,182,452.00

3. Contractor agrees that the amount of increase or decrease in the not -to-exceed amount specified in section 2, above, shall constitute full compensation for the additional and/or revised services specified in section 1, above, and shall fully compensate Contractor for any and all direct and indirect costs that may be incurred by Contractor in connection with such additional and/or revised services, including costs associated with any changes and/or delays in schedules or in the delivery of other services by Contractor.

4. Contractor warrants and represents that the person or persons executing this supplemental contrac t on behalf of Contractor has or have been duly authorized by Contractor to sign this supplemental contract and bind Contractor to the terms hereof.

5. Except as specifically revised herein, all terms and conditions of the Contract shall remain in full force and effect, and Contractor shall perform all of the services, duties, obligations, and conditions required under the Contract, as supplemented and modified by this supplemental contract.

[SIGNATURES ON FOLLOWING PAGE]

SUPPLEMENTAL CONTRACT
(Rev. 11-1-19)
A
pproval Recommended By: Approved As To Form By:

P roject Manager City Attorney
A
pproved By: Attest:
__ __________________________________
C ontractor City Clerk
A
pproved By:

Matt Eierman, Director of Public Works
City of Sacramento

Sacramento City CouncilFebruary 4, 2025

Sacramento City Council
February 4, 2025