EZ Liner Proposal (available in the City Clerk's Reading File) — Santa Clarita City Council, August 27, 2024

As part of this proposal the following information is being provided:

1. Proposal Price Sheet for the paint striping body.

2. A copy of EZ Liner's "Sourcewell Contract No. 080521-EZL-Specifications for EZ Liner Model TS-AL110 Base Unit Product Code #18C dated 08/05/2021".

3. A copy of City of Santa Clarita's "Specifications for an Airless Truck Mounted Striping Machine" dated 02/02/2024.

4. Comparison document comparing EZ Liner's Sourcewell specifications and City of Santa Clarita's specifications summarizing the changes.

5. Technical literature packet outlining what EZ Liner is proposing to provide.

This quote includes a one-year limited factory EZ Liner equipment warranty and the standard Isuzu chassis warranty.

The estimated availability of the completed truck shall be 180 days ARO / 90 days ARC (after receipt of chassis). EZ Liner production slots are issued based on receipt date of this executed agreement per the terms and conditions of this proposal. In the current post-pandemic market, global supply disruptions may cause shipment delays. Where the delivery of materials is delayed beyond the control of EZ Liner, EZ Liner shall not be liable for any additional costs or damages associated with such delays.

All prices quoted are valid for 30 days from the date of this proposal. All sales are FOB Orange City, Iowa. Freight quotes provided are estimated and subject to change. If the equipment is shipped, the actual freight cost will be invoiced at the time of shipment. Payment terms are 30% down with full balance due and payable within 30 days after shipment or pick up of the completed unit.

Any applicable federal, state, and local taxes, duties, fees, licenses, and other government charges in connection with this agreement are not included in pricing and are the responsibility of the customer.

Any surcharges imposed upon EZ Liner by its suppliers) may be passed on as additional charges to this agreement and shall fall under the same terms and conditions as this agreement. Such surcharges shall be documented with supplier notices or invoices.

If, during the performance of this agreement, the cost of materials significantly increases, through no fault of EZ Liner, the price of this agreement may be equitability adjusted by a reasonably necessary amount. As used herein, from the date of this quote a significant cost increase shall mean any increase in cost of materials which is abnormal, atypical, and typically would exceed seven percent (7%). Such increases in material cost shall be supported by quotes, invoices, or receipts.

Your signature below will signify that you have read this entire proposal and agree to its price, the equipment as listed and its terms and conditions. Please complete the Customer Approval section below. Send to your sales representative, this signed acknowledgment and, if applicable, your executed purchase order:

Mike Petersen
Territory Sales Manager
[email protected]
712-360-2108
The City's new paint truck will be delivered by lowboy trailer. The City will be responsible for driving their truck off the trailer.

EZ Liner looks forward to working with the City of Santa Clarita by providing quality paint striping equipment supported by superior customer service! Respectfully submitted, CUSTOMER APPROVAL:

Vogel Traffic Services, Inc. dba EZ Liner City of Santa Clarita, CA Signature kole Krammendk Signature
February 14, 2024 Date
Rob Krommendyk Printed Name
Design & Bid Project Manager II Title
EZ Liner • PO Box 140 • Orange City, IA 51041
P: (712) 737-4016 - TF: (800) 373-4016 - ezliner.com
EZ LINER MODEL TS-AL110, Product Code #18C

PAINT STRIPING BODY ONLY
Item Description List Price
18C AL110 Base Unit $ 184,070.00
18C-01-07 Air hose reel with 25' hose $ 1,738.00
18C-02-01 Vacuum bead load system $ 2,360.00
18C-04-01 Add'i paint & bead line with Graco guns $ 5,590.00 18C-04-02 Flex gun w/hose reel & 25' HP Hose $ 3,040.00 18C-04-03 220 gallon SS tank ILO Base $ 12,800.00
18C-04-04 120 gallon SS tank ILO Base $ 9,050.00
18C-04-05 1-1/2" LP SS Diaphragm pump, each $ 10,256.00 18C-06-01 25 gallon poly flush tank $ 2,450.00
18C-07-01 Skip-Line Inc. digital speedometer $ 1,680.00 18C-07-02 Gallon counts, per color $ 778.00
18C-07-03 Eight Light LED Work Light system $ 3,880.00
18C-07-04 1020F-4 Message Board ILO base $ 18,952.00
18C-07-05 Camera guidance system $ 13,680.00
18C-07-06 Laser guidance system $ 10,200.00
18C-07-07 3'6' Arrowboard ILO base TAC8 Arrow Stick $ 4,570.00 18C-08-01 Deduct for Mechanical Line Guide (4,970.00)
18C-08-02 Aluminum toolbox $ 1,119.00
18C-10-05 AL125 Base Unit Recommended Spare Parts Kit $ 9,375.00 F.O.B. FACTORY. TRAINING AND DELIVERY PRICED SEPARATELY.

A 7% DISCOUNT ON BASE UNIT AND ITEMS LISTED ON THIS PRICING PAGE IS AVAILABLE TO SOURCEWELL MEMBERS.

EFFECTIVE DATE: October, 2023.

EZLINER A DIVISION OF VTS
February 14, 2024
City of Santa Clarita "piggy-back" from Madera (Sourcewell Account #27811) 25663 Avenue Stanford
Santa Clarita, CA 91355
Re: Sourcewell Contract No. 080521-EZL (piggy-back) Purchase of EZ Liner Model TS-AL150 Truck Mounted Striping Machine (S/N 1E23556TS)-Price Sheet
Item Description List Price
18C TS-AL110 Base Unit $184,070.00
18C-02-01 Vacuum Bead Load System using Shop Air 2,360.00 18C-04-01 Add'1 paint & bead line with Graco guns 5,590.00 18C-07-01 Skip-Line Digital Speedometer 1,680.00
18C-07-02 Gallon Counts Per Color $778.00 × 3 2,334.00
18C-07-03 Eight Light LED Work Light System 3,880.00
18C-07-06 Laser Guidance System 10,200.00
18C-07-07 3'x6' Arrow Board ILO Base TAC Arrow Stick 4,570.00 18C-08-02 Aluminum toolbox $1,119.00 x2 2,238.00
Subtotal $216,922.00
7% Discount ($15,185.00)
Net Amount Published Pricing $201,737.00
Chassis
2024 Model Year Isuzu NPR HD Gas $52,559.00
Sourced Goods
Skip Line Remote Trigger for SC-12, Each $1,040.00 x 2 2,080.00 Weldex Rearview/Backup Camera System 2,398.00
Dual color plumbing on paint Guns on Left Carriage 1,543.00 (2) Drum Mount Agitator Assemblies, Each $1,960.00 × 2 3,920.00 Black Paint System-40-gal. Tank with agitator, 8.6 GPM Pump; & HP Pump Plumbed to Load Black Paint 4,935.00
Hydraulic 01l Cooler 1,420.00
2n° Model SC-12 Skip Timer 3,000.00
Strobe System California Title 13 Compliant 2,663.00
Three-Day Training Session 6,000.00
Delivery 6,500.00
Total for Sourced Goods $34,459.00
SUBTOTAL AMOUNT $288,755.00
Trade-in-offer for used Windrunner (11 years old) ($4500.00) TOTAL NET AMOUNT S284,255.00
Respectfully submitted, CUSTOMER APPROVAL
'ogel Traffic Services, Inc. dba EZ Line City of Santa Clarita, CA Signature
Date February 14, 2024 Date_
Rob Krommendyk Printed Name
Design & Bid Project Manager Title_
EZ Liner • PO Box 140 • Orange City, IA 51041
P: (712) 737-4016 • TF: (800) 373-4016 - ezliner.com
SOURCEWELL CONTRACT #080521

SPECIFICATIONS FOR ROADWAY MAINTENANCE EQUIPMENT
EZ LINER MODEL TS-AL110 BASE UNIT
18C
08/05/2021
applications speeds shall be from 4 MPH to 10 MPH. Application rates of 12 mil to 15 mil wet film thickness paint for standard formulations of traffic paint and 6 to 8 1bs./gal and Type I glass beads. The unit is designed so that it operates in its own lane of traffic and applies centerline, edge lines and lane lines separately.

Equipment platform: The construction shall be of 3/16" thick smooth aluminum deck plate 88" wide x length as required for components with 4" aluminum long sills, 3" aluminum cross members with integrally formed rub rail.

Walking area surfaces of platform shall be covered with anti-slip material. A canopy shall be provided above the operator stations. Deck shall be installed on chassis frame rails using 8" to 10" steel risers that are bolted to the chassis frame rails and long sills. The railings shall be 42" high with mid rail welded to deck with two (2) 32" high fold up steel ladders with a chrome grab handle each side of ladder openings and rear access. At the operator station the railing shall be 32" high with a mid rail. Steel rear bumper with stair step rear access incorporated into the design with right side hand railing. Removable aluminum rear fenders with aluminum guard forward and to the rear shall be provided.

LED platform lighting. Two (2) 10# fire extinguishers and two (2) cup holders shall also be provided. The auxiliary engine and air compressor shall remain their original factory colors. The underside of the deck will be painted the same color as the top of the deck. All coatings shall be lead free. The Unit shall be prime coated with a two-component urethane primer system. The topcoat shall be a two-component polyurethane coating. White is the standard factory paint color. Black powder coating shall be used on brackets, gun carriages and line

3.0 Operator seats: Two (2) Bostrom air ride high back black vinyl covered seats with seat belts and seat tethers and inside armrest. At the top of the railing at each operator station a black vinyl covered padded armrest 3'x18" shall be provided.

4.0 Gun carriages: Municipal type gun carriage centerline and edge line carriages 1 position and adjustable gun brackets are to be zinc plated. Two (2) paint guns ld two (2) bead guns installed on lett gun carriage and one (1) paint gun ar ne (1) bead gun on the right gun carriag

5.0 Mechanical line guide: A front mount laterally adjustable line guide wit extension 6' to 10' with pneumatic swivel caster and pneumatic lift

6.0 Paint supply: A drum storage area shall be provided capable of holding two (2) 55 gal. paint drums securely held in place with a web strap retention system.

Paint re-circulation shall be provided. A stand tube shall be supplied for each paint suction hose suction tube.

7.0 High pressure paint pumps: Two (2) Titan/Speetlo Model 415-315 paint pumps with a combination of leather/UHMWPE packings rated at 8.6 GPM @ 000 PSI shall be provided. Each pump shall be equipped with an 18 sq. in nigh-pressure stainless-steel paint filter with 40 mesh screens, an ASME certifier high-pressure stainless-steel surge chamber and check valve.

8.0 Low pressure paint filtration: Y type strainers shall be installed in the low- pressure plumbing connecting the paint supply tanks to the High-pressure paint pumps. A removable stainless-steel screen shall include approximately 1/8"

9.0 Paint guns: Three (3) Graco Model 238-377 paint guns with heavy duty reversible spray tips shall be provided. Full length 3/8"ID nylon lined high pressure paint hoses with 3/8" NPT plated female swivel fitting on both ends shall be provided from the surge chambers to the paint guns.

10.0 Bead supply: A 750# bead tank with three (3) 2" sight glasses shall be provided

11.0 Bead guns: Three (3) Graco Model 238-338 bead guns shall be provided. Full length ¾" ID clear poly-spring bead hoses to be provided from the bead manifold under the bead tank to the bead guns.

12.0 Air supply: Air supply shall be supplied by a belt driven 30 cfm air compressor.

The system shall include a 12-gallon air tank and LaMan 107F extractor/ dryer with auto drain. Two (2) air take off quick disconnect ports shall be provided- one at each gun carriage. A preset regulator shall be provided for carriage down pressure. A liquid filled system air pressure gauge shall be provided at the operators' station along with liquid filled gauges and air pressure regulators for head tank pressure

13.0 Auxiliary engine: A Honda Model GX690 23 hp gas engine shall be provided with controls at the engine. A separate CARB compliant 7-gallon gas tank and battery shall be provided for the Honda gas engine.
2 14.0 Hydraulic power: A 12-gallon hydraulic oil reservoir with sight level/temperature gauge, suction screen and return line filter with condition indicator shall be provided along with a belt driven pressure compensated piston type hydraulic pump. Gun carriages shall be positioned using a power steering system with tilt steering wheel with spinner knob at each operator position and 5' hydraulic cylinder for each carriage. A hydraulic by-pass shall allow a no-load start for the auxiliary engine.

15.0 Electrical system: A chassis cab control console shall be provided in the chassis cab containing the driver's controls for the paint striping body. Each circuit shall be color coded wire and shall have circuit protection. The wiring harnesses between the junction blocks to be protected by protective split loom covering. An LED white/red light with self-contained switch installed above each operator position. The electrical junction blocks and main components of the timer system shall be installed in an above deck weatherproof electrical box.

16.0 Skip line control system: One (1) Skip-Line, Inc. Model SC-12 Skip Timer shall be provided. Each operator position shall be wired to accept the timer, which can be installed at either position. Ground speed signal shall be obtained from a heavy-duty aluminum wrap installed on the chassis driveshaft.

17.0 Intercom system: A three position David Clark Model U3800 intercom system shall be provided with a dual headset port at the driver's position and a single port at each operator position. The following headsets shall be provided-one (1) Model H3492 single muff and two (2) H3432 dual muff design. Three (3) headset storage hooks shall be provided.

18.0 Safety lighting: The following Whelen LED amber strobe lights shall be provided-Four (4) Model L41AP 360° Super-LED beacons, one on each front corner of deck or on a chassis cab roof bracket and one on each corner of the platform at the rear of unit. Two (2) Model LINV2A Super-LED 180° mini strobe lights on gun carriages with one installed on outside edge of each gun carriage.

19.0 Electric actuators: Three (3) electric gun actuators shall be provided to remotely adjust the height of the paint guns. Control switches shall be provided on each respective Model SC-12 Master Control Box to control the height of the paint guns on each respective gun carriage.

20.0 LED Arrow stick: 47.75" long, 8 lamp Whelen Model TAC8 with controller in chassis cab

21.0 Drawings & technical literature: A complete set of drawings shall be submitted. These drawings shall show the deck layout and weight distributions 3 of the proposed unit. Descriptive literature, technical data and photographs shall be included with proposal.

22.0 Technical support: Training is not included in the base price but will be priced out on a case-by-case basis as a "sourced good" as part of the agreement with the individual customer. Two (2) consecutive days of training to instruct customer personnel in the operation and maintenance of the unit are recommended. After the completed truck has been received and accepted by the customer, the training will be scheduled. The customer is responsible for providing the paint and glass beads to be used during the training. Two (2) sets of Operation/Maintenance manuals shall be provided for the paint striping body on flash drives. Chassis manuals to be purchased by customer from their chassis vendor.

23.0 Chassis: Cab and chassis are not included. Specifications for the customer supplied cab and chassis must be approved by EZ Liner Engineering prior to purchase to ensure modification costs will not be incurred.

24.0 Delivery: The estimated delivery time is 120 days ARC (after reccipt of chassis). The completed truck may be driven out for delivery or delivered via lowboy trailer. The production schedule along with the time frame for delivery will be discussed and confirmed at time of order

25.0 Warranty: EZ Liner warrants all equipment manufactured by it and bearing its brand names to be free from defects in material and workmanship at the time of sale by EZ Liner or an authorized distributor. EZ Liner will for a period of twelve months from the date of sale, repair or replace any part of the equipment proven defective.

Specifications for An Airless Truck Mounted Striping Machine City of Santa Clarita, California
02/02/2024

1.0 Performance specification: Unit shall be capable of applying 3" to 8" wide retro-reflective lines with spacing between lines from 0" to 6". Paint applications speeds shall be from 4 MPH to 10 MPH. Application rates of 12 mil to 15 mil

2.0 Equipment platform: The construction shall be of 3/16" thick smooth aluminum deck plate 88" wide x length as required for components with 4" long sills, 3" cross members with integrally formed rub rail. Walking area surfaces of platform shall be covered with anti-slip material. An aluminum canopy shall be provided above the operator stations. Deck shall be installed on chassis frame rails using 8" to 10" steel risers that are bolted to the chassis frame rails and long sills. The railings shall be 42" high with mid rail welded to deck with two (2) 32" high fold up steel ladders with a chrome grab handle on each side of ladder openings and rear access. At the operator station the railing shall be 32" high with a mid rail. Steel rear bumper with stair step rear access incorporated into the design with right side hand railing. Removable aluminum rear fenders with aluminum guard forward and to the rear shall be provided. LED platform lighting. Two (2) 10# fire extinguishers and two (2) cup holders shall also be provided. The auxiliary engine and air compressor shall remain their original factory colors. The underside of the deck will be the same color as the top of the deck. All coatings shall be lead free. The Unit shall be powder coated with a Peridium T75 TGIC Polyester system. White is the standard factory paint color.

Black powder coating shall be used on brackets, gun carriages and line guide.

3.0 Operator seats: Two (2) Bostrom high back black vinyl seats mounted on air- ride suspension with seat belts and seat tethers and inside armrest. At the top of the railing at each operator station a black vinyl covered padded armrest 3"x18" shall be provided.

4.0 Toolboxes: Two (2) 18 X 18 X 24 aluminum diamond plate toolboxes mounted on the rear bumper.

5.0 Gun carriages: Municipal type gun carriage centerline and edge line carriages mounted in front of the rear axle. Each carriage shall be supported by a single outrigger tube retractable structural steel slide with UHMWPE bearing material and a single standard gun carriage tire installed in a center swivel. Carriages shall be supported by auto lock brackets in the transport position and adjustable gun brackets are to be zinc plated. Three (3) paint guns and three (3) bead guns installed on left gun carriage with two paint guns painting yellow or white paint and one paint gun painting white or black paint. One (1) paint gun painting white paint and one (1) bead gun on the right gun carriage.

LEFT CARRIAGE RIGHT CARRIAGE
Y/W W/Bk Y/W

G G G G

6.0 Mechanical line guide: A front mount laterally adjustable line guide with extension 6' to 10' with pneumatic swivel caster and pneumatic lift.

7.0 Paint supply: A drum storage area shall be provided capable of holding two (2) 55 gal. paint drums securely held in place with a web strap retention system.

One drum for yellow paint and one drum for white paint. Paint re-circulation shall be provided. Two (2) hydraulic powered paint agitators shall be provided with one installed in each paint drum. Black paint system with 40-gallon paint tank with hydraulic driven paint agitator and black paint gun on left gun carriage.

Black HP paint pump to be plumbed to load black paint under low pressure.

8.0 High pressure paint pumps: Three (3) Titan/Speeflo Model 415-315 paint pumps with a combination of leather/UHMWPE packings rated at 8.6 GPM @ 2000 PSI shall be provided. One pump for yellow, white, and black paint. Each pump shall be equipped with an 18 sq. in. high-pressure stainless-steel paint filter with 40 mesh screens, an ASME certified high-pressure stainless-steel surge chamber, check valve, and stand tube.

9.0 Low pressure paint filtration: Y type strainers shall be installed in the low- pressure plumbing at the inlets to the high-pressure paint pumps. A removable stainless-steel screen shall include approximately 1/8" diameter holes.

10.0 Paint guns: Four (4) Graco Model 238-377 paint guns with heavy duty reversible spray tips shall be provided, three (3) XHD-545 tips-one for each paint gun on left gun carriage, and one (1) XHD-555 tip for white gun on right gun carriage. Full length 3/8"ID nylon lined high pressure paint hoses with 3/8" NPT plated female swivel fitting on both ends shall be provided from the surge chambers to the paint guns.

11.0 Bead supply: A 750# bead tank with three (3) 2" sight glasses shall be provided. Vacuum bead loading shall be provided using the City's shop air compressor.

12.0 Bead guns: Four (4) Graco Model 238-338 bead guns shall be provided. Full length ¾" ID clear poly-spring bead hoses to be provided from the bead manifold under the bead tank to the bead guns.

13.0 Air supply: Air supply shall be supplied by a belt driven 30 cfm air compressor.

The system shall include a 12-gallon air tank and LaMan 107F extractor/ dryer with auto drain. Two (2) air take off quick disconnect ports shall be provided-one 2 at each gun carriage. A preset regulator shall be provided for carriage down pressure. A liquid filled system air pressure gauge shall be provided at the air compressor, also a liquid filled gauge and air pressure regulator for bead tank pressure shall be installed on the bead tank.

14.0 Auxiliary engine: A Honda Model GX690 23 hp gas engine shall be provided with controls at the engine. A separate CARB compliant 7-gallon gas tank and battery shall be provided for the Honda gas engine.

15.0 Hydraulic power: A 12-gallon hydraulic oil reservoir with sight level/temperature gauge, suction screen and return line filter with condition indicator shall be provided along with a belt driven pressure compensated piston type hydraulic pump. Gun carriages shall be positioned using a power steering system with tilt steering wheel with spinner knob at each operator position and 5' hydraulic cylinder for each carriage. A hydraulic bypass shall allow a no-load start for the auxiliary engine. A hydraulic oil cooler shall be provided.

16.0 Electrical system: A chassis cab control console shall be provided in the chassis cab containing the driver's controls for the paint striping body. Each circuit shall be color coded wire and shall have circuit protection. The wiring harnesses between the junction blocks to be protected by protective split loom covering. An LED white/red light with self-contained switch installed above each operator position. The electrical junction blocks and main components of the timer system shall be installed in an above deck weatherproof electrical box.

Gallon counts with (3) stroke counters one for each HP paint pump. Eight (8) Hella 2000 lumen LED work lights. GL3000-P guidance laser installed on chassis cab roof using a roof bracket. Weldex rearview/backup color camera system using Model WDRV-7057C camera with Model WDRV-7041M 5" monitor.

17.0 Skip line control system: Two (2) Skip-Line, Inc. Model SC-12 Skip Timers shall be provided. Black paint pattern option shall be provided to turn off beads for black paint guns. Two (2) remote triggers with one for each timer. Ground speed signal shall be obtained from a heavy-duty aluminum wrap installed on the chassis driveshaft. A Skip Line digital speedometer shall be installed in the chassis cab near the driver.

18.0 Intercom system: A three position David Clark Model U3800 intercom system shall be provided with a dual headset port at the driver's position and a single port at each operator position. The following headsets shall be provided-one (1) Model H3492 single muff and two (2) H3432 dual muff design. Three (3) headset storage hooks shall be provided

19.0 Safety lighting: The following Whelen LED amber strobe lights shall be provided-Four (4) Model L31HAFCA 360° Super-LED beacons, one on each front corner of deck and one on each corner of the platform at the rear of unit. 3 Two (2) Model IONSVIA Super-LED 180º mini strobe lights on gun carriages with one installed on the outside edge of each gun carriage. The Whelen LED strobe light system shall be California Title 13 compliant.

20.0 Electric actuators: Four (4) electric gun actuators shall be provided to remotely adjust the height of the paint guns. Control switches shall be provided on each respective Model SC-12 Master Control Box to control the height of the paint guns on each respective gun carriage.

21.0 LED Arrow Board: Actuated National Signal 3'×6' 25 light LED arrow board.

Controller to be installed in chassis cab.

22.0 Drawings & technical literature: A complete set of drawings shall be submitted. These drawings shall show the deck layout and weight distributions of the proposed unit. Descriptive literature, technical data and photographs shall be included with the proposal.

23.0 Technical support: Three (3) consecutive days of training to instruct customer personnel in the operation and maintenance of the unit to be provided. After the completed truck has been received and accepted by the customer, the training will be scheduled. The customer is responsible for providing the paint and glass beads to be used during the training. Two (2) sets of Operation/Maintenance manuals shall be provided for the paint striping body on flash drives. Chassis manuals to be purchased by the customer from their chassis vendor.

24.0 Chassis: The chassis shall be a 2024 Isuzu Model NPR-HD gas chassis rated at 14,500# GVWR; 6.6L V8 gas engine 350 hp @ 4500 rpm, 425 #/ft. of torque; 6- speed automatic transmission; 38.6-gallon fuel tank; heat & air conditioning; fire extinguisher, triangle kit; backup alarm; AM/FM/Bluetooth radio; white.

25.0 Delivery: The estimated delivery time is 120 days ARC (after receipt of chassis). The completed truck may be driven out for delivery or delivered via lowboy trailer. The customer is responsible for driving their new paint truck off the trailer. The production schedule along with the time frame for delivery will be discussed and confirmed at the time of order.

26.0 Warranty: EZ Liner warrants all equipment manufactured by it and bearing its brand names to be free from defects in material and workmanship at the time of sale by EZ Liner or an authorized distributor. EZ Liner will for a period of twelve months from the date of sale, repair or replace any part of the equipment proven defective.

27.0 Factory Pre-delivery Inspection Meeting-The customer is not interested in coming to the factory for PDI Meeting per the Customer Questionnaire. NOTE- This meeting is not part of the Sourcewell contract for the Model TS-AL110. 4 EZLINER A DIVISION OF VTS
February 14, 2024
City of Santa Clarita "piggy-back" from Madera (Sourcewell Account #27811) 25663 Avenue Stanford
Santa Clarita, CA 91355
Comparison: Sourcewell Contract No. 080521-EZL Specifications for EZ Liner Model TS-AL110 Base Unit Product Code #18C dated 8/05/2021 To: City of Santa Clarita's Specifications for an Airless Truck Mounted Striping Machine Dated 02/02/2024.

The following items listed in the City's specifications are changes to the contract specifications that come under Published Options:

1. Page 2; 10.0-Vacuum Bead Loading-Page 2; 11.0-Vacuum bead loading using the City's shop air compressor has been added. This change is covered by Option Code 18C-02-01.

2. Page 2; 9.0-Paint guns & 11.0 Bead guns-Page 2; 10.0 & 12.0-An additional paint and bead line with Graco guns has been added to the left carriage. This change is covered by Option Code 18C-04-01.

3. Page 3; 16.0-Digital Speedometer-Page 3; 17.0-A Skip-Line digital speedometer installed in the chassis cab has been added. This change is covered by Option Code 18C-07-01.

4. Page 3; 15.0-Gallon Counts-Page 3; 16.0-Three (3) stroke counters-one for each high- pressure paint pump have been added to the specifications to keep track of gallons painted. This change is covered by Option Code 18C-07-02.

Page 3 ends

2000 lumen work light system has been added. This change is covered by Option Code 18C-07-03.

6. Page 3; 15.0-Laser Guidance System-Page 3; 16.0-The Model GL3000-P remote controlled laser has been added. The laser will be installed on a roof bracket on the chassis cab roof. This change is covered by Option Code 18C-07-06.

7. Page 3; 20.0-3'x6' Arrow Board-Page 4; 21.0-The Whelen Traffic Advisor has been replaced with a 3'x6' actuated 25 LED light arrow board. This change is covered by Option Code 18C-07-07.

8. Page 1; 2.0-Toolboxes-Page 1; 4.0-Two (2) aluminum toolboxes mounted on the surface of the rear step bumper have been added. This change is covered by Option Code 18C- 08-02.

The following items listed in the City's specifications are changes to the contract specifications that come under Sourced Goods:

9. Page 4; 24.0-Chassis-Page 4; 23.0-An Isuzu Model NPR gas chassis has been added to the specifications. An addition has been included for this change.

10. Page 3; 17.0-Remote Triggers for SC-12 Timers-Page 3; 16.0-Two (2) remote triggers have been added to the specifications with one to be provided for each Model SC-12 timer box. An addition has been included for this change.

11. Page 3; 16.0-Weldex Rearview/Backup Camera-Page 3: 15.0-A Weldex color rearview/backup camera with 5" monitor installed in the chassis cab has been added. An addition has been included for this change.

12. Page 2; 5.0-Dual Color Paint Guns-Page 1; 4.0-The two (2) yellow paint guns on the left gun carriage have had white paint added to them to change them to dual color paint guns. An addition has been included for this change.

13. Page 2; 7.0-Drum Mount Paint Agitators-Page 2; 6.0-Two (2) hydraulic powered paint agitators have been added with one for yellow paint and one for white paint. An addition has been included for this change.

14. Page 2; 7.0-Black Paint Svstem-Page 2-A 40-gallon stainless-steel paint tank with hydraulic powered agitator has been added for the black paint system. Also added for the black paint system is a Titan 8.6 gpm paint pump with a Y strainer low-pressure paint filter, a high-pressure paint filter and an ASME surge chamber. This pump will also be used for loading black paint under low pressure. A stand tube to be included with 2"ID x 12' load hose with 1 ½" Ss pipe x 40" load tube with 90°elbow with cam & groove fitting. An addition has been included for these changes.

15. Page 3; 15.0-Hydraulie Oil Cooler-Page 3; 14.0-A hydraulic oil cooler has been added because of the average monthly temperatures for the City of Madera. An addition has been included for this change.

16. Page 3; 17.0-2nd Model SC-12 Timer-Page 3; 16.0-So the operators don't have to switch the timer between operator positions, a second Model SC-12 timer has been added. An addition has been included for this change.

17. Page 3; 19.0-Strobe Light System-Page 3; 18.0-The standard model four (4) 360° strobe lights and two (2) 180° strobes have been replaced with models that are California Title 13 compliant. An addition has been included for these changes.

18. Page 4; 23.0-Technical Support-Training-Page 4; 22.0-Per the City's request a three- day training session has been added. An addition has been included for the training session.

19. Page 4; 25.0-Delivery-Page 4; 24.0-A quote was received for the delivery trip to the City of Madera. An addition has been included for the delivery trip.

EZ Liner • PO Box 140 • Orange City, IA 51047
P: (712) 737-4016 - TF: (800) 373-4016 - ezliner.com

CITY OF SANTA CLARITA, CALIFORNIA
EZ LINER MODEL TS-AL150

TECHNICAL SUPPORT DOCUMENTATION

TABLE OF CONTENTS
EZ Liner Sourcewell Literature
EZ Liner Custom Truck Literature

Page 1 ends

Page 2 ends

Page 3 ends

Page 4 ends

EZLINER®
ZLINER
Sourcewell →
Official Vendor: Contract #080521-EZL
Together, Sourcewell and EZ Liner offer the widest range of products and materials for pavement marking and maintenance.

Sourcewell
Awarded Contract
Contract # 080521-EZL

CUSTOMUINER
The CustomLiner Series products from EZ liner are custom built to meet specific requirements while exceeding expectations. The custom built approach means the equipment is tailored to meet any demand while being dependable, safe, and easy to operate.

AL500+ AL220 AL110
SOURCEWELL CODE: 18A SOURCEWELL CODE: 18B
SOURCEWELL CODE: 18C
AirSpray Stencil Unit TrailRunner
• We offer a variety of paint systems to • Large range of options to fit budget • Unparalleled adaptability, whether meet every need. and project needs. Available in you need to stripe a sports field or a SOURCEWELL CODE: 18G palletized units and trucks.

SOURCEWELL CODE: 18F SOURCEWELL CODE: 18D
EZ Liner • Box 140 • Orange City, IA 51041 • P: (712) 737-4016 • TF: (800) 373-4016 • ezliner.com 3 CUSTOMUNER Paint Trucks
Custom Built Solutions
EZ Liner offers the widest range of custom-built, truck mounted latex paint stripers available today. Our custom-built approach means you will get the striper Under 500 gallons
500 - 1000 gallons
V Base Unit Specifications
• Utilization of components recognized and trusted as • Variety of paint-delivery systems, including airless and professional, durable, dependable and cost effective airspray technologies • Engineering-generated weight-distribution layouts to ensure • Simplified and convenient plumbing, wiring, and controls compliance with vehicle and legal limits for ease of use and efficiency • High-quality welds and strong platform, railing and ladder • Guiding tools options such as highlift mechanical, laser construction and video camera
EZLINER EZ Liner | 1920 Albany Place SE, Orange City, IA 51041 | (800) 373-4016|| ezlinerarrow.com

ZZLINER

A DIVISION OF VTS
Platform Construction
• Heavy duty 3/16" thick smooth aluminum plate platform surface with rolled edges to create a one-piece integrally formed 5 ½" tall rub-rail and capped ends for finished corners.
• Safe, corrosion resistant rolled edges without gaps, cracks, or channels in which debris builds up and moisture can occur over time.
• Structural channel sub frame, 4" longitudinal stringers • 3" cross members on maximum 21" centers
Various metals, dimensions, and designs available
Grade 8 riser bolts, 8" risers
6" wide anti-slip grip tape applied to all open walking areas, spaced 3" apart Safety railings welded to perimeter of deck for stability and rigidity Accept no exceptions or equals!
Descriptive, Not Restrictive. EZ-Liner's continuing quest for improvement make equipment, specifications, and components subject to change without notice.

EZ LINER

A DIVISION OF VTS
High Visibility Rear Operator's Canopy
• Durable high quality 92" wide × 60" deep × 76" high (above the floor of the operator's platform) structure.

Maximum visibility of gun carriages with no obstructions in operator's line of sight.

Padded 32" side railings for operator comfort & safety. • Frame includes center and corner vertical posts constructed of heavy duty walled 2" x 2" square tubing, long base members, and gusseted for added strength. r 10-gauge overhead canopy with rust resistant welded joints, edges, and corners. • Various cost-effective metals, dimensions, and designs available.

ELINER
Accept no exceptions or equals!
Descriptive, Not Restrictive. EZ-Liner's continuing quest for improvement make equipment, specifications, and components subject to change without notice.

EZLINER

A DIVISION OF VTS
Safety Ladder Construction
• Rugged 1 ½" steel square tube construction
• Heavy duty bullet type low profile hinges with rounded ends for safety Flush fitting with platform railing vertical posts when stored upright Fail-safe spring loaded pawl type finger pull pin type latch Folds down at a slight angle for ease of operator use
• 25" long chrome handrail mounted vertically on each side of ladder entrance • Perforated horizontal step rungs for a slip free sure grip Accept no exceptions or equals!
Descriptive, Not Restrictive. EZ-Liner's continuing quest for improvement make equipment, specifications, and components subject to change without notice.

EZLINER

A DIVISION OF VTS
Rear Step Bumper Construction
• Heavy duty "C" channel steel frame rail extensions and step bumper support. • Safe, rust resistant capped ends, rolled edges without gaps, cracks, etc. in which debris builds up and moisture can occur over time.
v 3/16" formed steel channel staircase style steps 6 ½" deep each with rolled bottom edge for finished look and enhanced safety.
• Bottom step bumper standard widths of 88" and 96", with other dimensions and design customization available upon request.

Heavy duty high traction abrasive step surfaces for secure and safe footing.

Full width conspicuity tape facing rear for maximum motorist visibility.

Chrome grab handle(s) for better on and off balance and stability. ~ 18" (approximate) 1s' step height from pavement also offers rear under-ride protection.

Accept no exceptions or equals!
Descriptive, Not Restrictive. EZ-Liner's continuing quest for improvement make equipment, specifications, and components subject to change without notice.

Diamond® Vogel
Peridium® T75
Low Cure Super Durable TGIC Polyester Powder Coatings
Peridium T75 Powder Coatings offer excellent application and performance characteristics. Diamond Vogel's focus on tightly controlled particle size distribution promotes ideal first-pass transfer efficiency. Peridium T75 provides very good exterior durability and overbake resistance. This coating provides a good balance between smoothness and edge coverage while being economical.

TYPICAL APPLICATIONS CURED FILM PROPERTIES
• Agricultural equipment • Construction equipment PCI Powder Smoothness Rating 6 (high gloss) • Recreational equipment • Lawn and garden equipment Specific Gravity (ASTM D792) 1.2 to 1.8 • Electrical enclosures • Patio Furniture Adhesion (ASTM D3359) 5B (100%) • Wheels and rims Gloss (ASTM D523) 55-99
Pencil Hardness (ASTM D3363) 2H+
CURE SCHEDULE Impact (ASTM D2794) up to 160 inch Ibs
Flexibility (ASTM D522) 1/8 inch - No cracking
425
Humidity (ASTM D2247) 1,000+ hours
400 Salt Spray (ASTM B117) 1,000+ hours
*Film properties are dependent on gloss, pigmentation, film thickness, and cure temperature.

Pes Met Temperasure F STORAGE AND HANDLING
325
Diamond Vogel powder coatings should be stored at normal room temperature and humidity (less than 80°F and 50-60% RH). Shelf life will be approximately six months to over a year depending on storage conditions. Always rotate inventories 250% to ensure trouble-free powder application. When storage 10 15 20 25 30
Time (min) conditions are not the same as the application area, allow a 24 hour acclimation period within the application area to prevent • Typical cure schedule 10 minutes @ 320°F moisture condensation in the powder. Always protect virgin and reclaim powder from excessive heat and humidity.
• Non-blooming
• Recommended for coating parts composed of mixed light INDUSTRIAL HYGIENE and heavy gauge metal mass
Powder handling should always be done in conjunction with proper dust collection and personal protective equipment.

Please refer to the Safety Data Sheet for more detailed information.
48389-DV (62397) 12/22
Diamond Vogel| Industrial Coatings
1020 Albany Place SE • Orange City, IA 51041
(712) 737-4993 • [email protected] diamondvogel.com/industrial The technical data and suggestions for use contained in this document are true and correct to the best of our knowledae at the date of issuance. The statements of this document do not constitute a wananty, expressed or implied, as t the perfonnance of these products. Since Diamond Vogel does not control the application of its products or the condition of the surfaces to which they ale applied, Diamond Vogel's liability wili under no circumstances exceed replacement afthe noduck All technical informatlan is subleetto chanas without notice Diamond©Vogel

POWDER COATINGS
Peridium'T
ET13-53554-750 PB White 520 S/D TGIC
Polyester
Lot # 28874-1 Cure Schedule 10 min. @ 390 °F Peak Metal Temp.
50 Lb DANGER!
ET19-53354:730 Nocif en can atle
Manufacture Date: 09/20/2023 PELIGRO! graves. Puede provocar una reaccion alárgica en la piel. Puede provocar defectos locivo en caso de ingestión. Nocivo en caso de inhalación. Provoca leslones oculares Box: 3 Harmful If swallowed. Harmful it Inhaled. Causes serious eye damage, May cause DANGER! an allergic skin reaction. May cause genetic defects. Suspected of causing Appearance: Powder Physical State: Powder Odor: No Information availabie Precautionary Statements • Prevention: Obtain special Instructions before use. Do cancer.

Thoroughly after handing Do not est, drink or smoke when tang til produed skin nated are Contaminate work citing should not be alone a a ne

CULO CHICANO DE HUAL NOONS
or struction: Maintain alonge somperatures befo 80°F (20 ). Protest sign i reclaned powder hots sacessis hear and outiy. Shet ite tanges do t ve Buses a be Diamond Vogel | Industrial Coatings + Orange City, Iowa 51041 • (800) 728 6435 - diamondvogel FOR INDUSTRIAL OR COMMERCIAL USE ONLY

EZLINER

A DIVISION OF VTS
Rear Operator Air Ride Seats
• H.O. Bostrom ergonomically designed air-ride suspension • seat tethers, seat belt, flip-up armrests, and full backrest with lumbar support • 5" fore and aft adjustment range, 6" vertical air suspension range of travel, release lever for reclining back adjustment
• black Duracoat™ vinyl trim offers a cleanable surface protection, stain & abrasion resistance & improved wear
Accept no exceptions or equals!
Descriptive, Not Restrictive. EZ-Liner's continuing quest for improvement make equipment, specifications, and components subject to change without notice.

EZLINER

A DIVISION OF VTS
Toolbox
• heavy duty aircraft grade aluminum with treadbrite finish stainless steel T handle with key lockable recessed latch • interlocking with rubber gasket
standard size is 24" wide, 18" deep and 18" tall each, other sizes also available for custom design
• Mounted in easily accessible locations for operator convenience

LUM-LINE
Accept no exceptions or equals!
Descriptive, Not Restrictive. EZ-Liner's continuing quest for improvement make equipment, specifications, and components subject to change without notice.

EZLINER

A DIVISION OF VTS
Medium Duty Gun Carriage Outriggers
\ 10" diameter tire and center swivel caster same as the mechanical line guide wheel and caster assembly for interchangeability and spare parts inventory consideration.

Zine plated gun holding rods and brackets for durability and ease of overspray clean up. • Compact parallel hinged bar type construction absorbs terrain both horizontally and vertically, yet maintains rigidity from side to side, ensuring the straightest lines and the most consistent gun height relative to the pavement.
• Pneumatic air cylinder to lift the spray gun carriage off the road surface and to apply down pressure when striping.
• Tube in tube retractable structural steel slides with UHMW PE bearing material controlled with hydraulic steering.

Auto-hold transport bracket does not require chains to hold the carriage in place. • Trailing wheel design sets gun bars back behind the outriggers for optimal operator visibility.

Accept no exceptions or equals
Descriptive, Not Restrictive. EZ-Liner's continuing quest for improvement make equipment, specifications, and components subject to change without notice.

EZLINER

A DIVISION OF VTS
Mechanical Line Guidance System
• Rigid 2" square tube construction, powder coated finish for durability • Grease-able hinged block joint connection design for extreme angles Telescoping out to 10' extension with tool-less adjustability Reversible for positioning on either side of the truck
High lift air or hydraulic cylinder controlled from chassis cab Folds completely out of driver's view on front bumper when not in use Pneumatic swivel wheel with spring tension adjustment for stability Accept no exceptions or equals!
Descriptive, Not Restrictive. EZ-Liner's continuing quest for improvement make equipment, specifications, and components subject to change without notice.

EZLINER

A DIVISION OF VTS
Drum Draw Paint Supply System
• Deck space and a web strap retention system with hold downs to accommodate fully loaded 55-gallon paint drums with traffic paint.
• Drums when loaded onto the platform of the striping truck shall act as zero pressure storage containers to supply paint to the system.
• Stainless steel suction tubes and 1 ½" I.D. suction hoses to connect the paint pumps to the paint drums.
• Bleeder tubes from HP paint filter canisters to de-pressurize for cleaning and recirculate pressurized paint back to drums
• Safety chains and latches on each side of platform to ensure the platform side railing does not interfere with side loading of drums with a forklift. • Storage tubes in each storage section to provide a place to store suction and bleeder tubes and hoses when drums are switched.

Accept no exceptions or equals!
Descriptive, Not Restrictive. EZ-Liner's continuing quest for improvement make equipment, specifications, and components subject to change without notice.

EZ LINER

A DIVISION OF VTS
Zero Pressure 40 Gallon Black Paint Tank
• Completely removable bolted top for access with silicone airtight seal v l Rounded corners for safety
Graphite coating on interior walls for ease of end of season cleanup 10-gauge stainless steel walls with automotive exterior finish to match equipment body Heavy duty PVC pressure equalization vent to prevent pressure or vacuum build up v l Integral dipstick with twist off cap and T handle for paint level monitoring 6" × 12" inspection port lid with handle, gasket, and over-the-center latch • Hydraulic agitator with adjustable speed control
Accept no exceptions or equals
Descriptive, Not Restrictive. EZ-Liner's continuing quest for improvement make equipment, specifications, and components subject to change without notice.

EZLINER

A DIVISION OF VTS
Titan Speeflo HP Pump Model 989-120

HYDRAULIC POWERED AIRLESS PUMPS

MOTOR PUMP PUMP PUMP PUMP PUMP PUMP

PUMP TO PUMP OUTPLT OUTPUT OUTPUT OUTPUT /OUTPUT OUTPUT MODEL PUMP OUTLET CYCLE PER @ 40 @50 @ 60 @ 70
SERIES RATIO PRESSURE RATE CYCLE CYCLES CYCLES CYCLES CYCLES | CYCLES 441-315 2000 pai 7/gailorı 18:3 fl. oz 171 gpr 8.6 gpm 1UD gem [8.4 apm 13B bar: 1.8/liter 541 mil 160 269 0 32.6(pm 379|pm 93.2Ipm Accept no exceptions or equals!
Descriptive, not restrictive. EZ Liner's continuing quest for improvement make equipment, specifications, and components subject to change without notice.

EZLINER

A DIVISION OF VTS
ARO Ingersoll Rand
Industrial Technologies
300 STAINLESS STEEL CARTRIDGE MESH SIZE
651422-40 40

MATERIAL FILTER
MAXIMUM INLET PRESSURE 6,000 P.S.I. (414 Bar)
HP RECIRC 13
To include ½" high-pressure relief/bleeder hose back to tank or drums for ease of cleaning Accept no exceptions or equals!
Descriptive, not restrictive. EZ Liner's continuing quest for improvement make equipment, specifications, and components subject to change without notice.

EZLINER

A DIVISION OF VTS
ASME Certified Surge Chamber

EZLINER
immedianon
Accept no exceptions or equals!
Descriptive, not restrictive. EZ Liner's continuing quest for improvement make equipment, specifications, and components subject to change without notice.
054-A010-00
3 ITEM NO. Q TY. PART NUMBER DESCRIPTION
1 1 054-WO 10-00 SURGE CHAMBER, HP
2 1 SS5404-8-8 1/2" HEX NIPPLE, SS HP
3 1 | F12-16-1208 SS BUSHING, 3/4" TO 1/2". HP
Accept no exceptions or equals!
Descriptive, not restrictive. EZ Liner's continuing quest for improvement make equipment, specifications, and components subiect to change without notice.
aroetr

G GRACO EZLINER

A DIVISION OF VTS
Automatic Single Acting Paint Gun
Part Number (Model): 238377
Technical Data
Maximum working pressure 3000 psi (210 bar)
Operating pressure of air actuated trigger: Min 50 psi (3 bar) Max 200 psi (12 bar) Fluid connections two 3/8 npt(f) ports
Air connection 1/4 npt(f) air inlet
Wetted parts 303 & 416 Series Stainless Steel, Tungsten Carbide, Copper, Acetal Homopolymer, Leather
Operating temperature 32° - 120° F (0° - 49° C)
Sound pressure level 84.6 dB
Sound power level 90.9 dB
*Measurements at 2900 psi (200 bar) per ISO 3744
Accept no exceptions or equals!
Descriptive, Not Restrictive. EZ-Liner's continuing quest for improvement make equipment, specifications, and components subject to change without notice.

EZLINER

A DIVISION OF VTS
Glass Bead Tank
• 12 forged steel C-clamps with T handle head bolted lids and airtight gasket seal • A.S.M.E. certification standard on all pressure vessels • Hinged full top opening lid with handle welded to lid Instant glass bead level monitoring featuring large 2" diameter sight glasses installed at ¼, ½, and ¾ full
Heavy duty tank walls with plural component urethane automotive exterior finish • Splitter/strainer screen fits in neck of tank to catch debris while loading manually or with a vacuum bead loading system
Application pressure regulated from the top of the tank Preset safety pressure relief or "pop-off" valves
"LINER
Accept no exceptions or equals!
Descriptive, Not Restrictive. EZ-Liner's continuing quest for improvement make equipment, specifications, and components subject to change without notice.

EZLINER

A DIVISION OF VTS
PENBERTHY®
Jet pump
Vacuum Glass Bead Load System

PRESSURE RELIEF VALVE

BEAD SCHEMATIC

BEAD TANK VACUUM
AIR

DRYER SYSTEM

AIR PRESSURE

TANK GAUGE

REGULATOR

TANK DRAIN

VALVE OPEN E ATRSLPELY

VALVE CLOSED

VACUUM JET

SYSTEM PRESSURE- VALVE PUMP
BEAD TANK PRESSURE * ENCHAN

EXHAUST

VALVE BEAD LOAD VALVE

EXHAUST AIR

PRESSURE

VACUUM GAUGE

MUFFLER

BEAD TANK

COMPRESSOR

X BEAD TANK VALVE

I MARC B EZ-LINER INDUSTRIES
BEAD ORANGE CITY. IOWA 51041

MANIFOLD
02/10/2017 BEAD SYSTEM

VISUAL SCHEMATIC VACUUM
107257201s 7 Peak dont witne 101 Tom

GI TANK EXHAUST
Accept no exceptions or equals!
Descriptive, Not Restrictive. EZ-Liner's continuing quest for improvement make equipment, specifications, and components subject to change without notice.

G GRACO EZLINER

A DIVISION OF VTS
Automatic Single Acting Bead Gun
Part Number (Model): 238338
Technical Data
Valve Seat Nozzle Sizes: 0.170, 0.203, 0.234, 0.281, 0.344, 0.420 † † Nozzle size 0.420 is optional; order separately
Maximum working pressure 200 psi (12 bar)
Operating pressure of air actuated trigger: Min 50 psi (3 bar) Max 200 psi (12 bar) Air connection 1/4 npt(f) air inlet
Bead connection 3/4 npt(f) bead inlet
Glass bead output 2-40 Ib/min (0.9-18 kg/min)
Air consumption 1-2 cfm
Spray width 2-12 in. (50-304mm)
Operating temperature 32° - 120° F (0° - 49° C)
Sound pressure level <80 dB
Sound power level <80 dB
*Measurements at 120 psi Air Cylinder, 60 psi Air Bead
Accept no exceptions or equals!
Descriptive, Not Restrictive. EZ-Liner's continuing quest for improvement make equipment, specifications, and components subject to change without notice.

EZLINER

A DIVISION OF VTS
Honda Power Pack
• GX690 23 hp gas engine, 4-stroke, overhead valve, 2 cylinders (90° V-Twin) • Rol-Air K35 belt driven 30 displacement cfm air compressor. • Danfoss belt driven pressure compensated piston type hydraulic pump. • 12-gallon hydraulic reservoir with sight level/temp gauge.

HONDA
Accept no exceptions or equals!
Descriptive, not restrictive. EZ Liner's continuing quest for improvement make equipment, specifications, and components subject to change without notice.

EZLINER

A DIVISION OF VTS
La-Man Extractor/Dryer®
How Extractor/Dryers® Work:
© Compressed air containing tiny particles of dirt, dust, oil and moisture enters the first stage of the
Extractor/Dryer®.
© A coalescing effect occurs as air passes through a
cartridge mesh filter that captures particles and causes moisture to form larger droplets.
3 Air velocity lessens as it enters the extraction chamber allowing particles to collect and moisture to condense on the honeycomb.
4 Particle laden water flows along the bottom and out the drain.
6 Air passes through the second stage, wire supported
fiber, filter cartridge that captures remaining particles down to 5 micron.
® Remaining moisture and contaminates are dried and
filtered in the second stage filter.
© Exhaust air is clean and dry - no dirt, rust, oil or water droplets to disrupt air equipment operation.

MODELS NPT SCFM MAX SERVICE SIZE APPROX
PSI KIT (INCHES) WT. LBS
107F 1/2' 50 250 OSOSKA 8-1/4 × 4x2-1/2 3#
Accept no exceptions or equals!
Descriptive, not restrictive. EZ Liner's continuing quest for improvement make equipment, specifications, and components subject to change without notice.

SPECIFICATIONS
FILTRATION 5 MICRON"
AIR FLOW 50 SCM
MAXIMUM PRESSURE 250 PSIG
DEW POINT 10 TO 35° F @

ATMOSPHERIC PRESSURE
PORT SIZE MODEL 105 1/4" NPT
MODEL 106 3/8" NPT
MODEL 107 1/2" NPT
HEIGHT 9.00°
WIDTH 4.00"
DEPTH 2.50"
BOLT TORQUE 50 INCH POUNDS
MAXIMUM TEMPERATURE 180° F
*SERVICE ITEMS 050SK SERVICE KIT
PATENT NO. RE. 32, 989 - 5,261,946
0420
Accept no exceptions or equals!
Descriptive, not restrictive. EZ Liner's continuing quest for improvement make equipment, specifications, and components subject to change without notice.

HELLA EZLINER

A DIVISION OF VTS
HELLA ValueFit 5 RD LED 2.0
Features:
• Compact round design
• 14 high performance LEDs
• Color temperature: 6500k
Specifications:
• Voltage: 9-33VDC
• Current Draw: 2.08A @ 12V, 1.04A @ 24V
• Power Consumption: 24W
• Luminous Flux (measured): 2000 Im
• Certificate: CE, RoHS, IP67, IP69K, Emark
• Packaging: Blister
• Minimum Order Qty: 1
Technology:
• LED
Accept no exceptions or equals!
Descriptive, Not Restrictive. EZ-Liner's continuing quest for improvement make equipment, specifications, and components subject to change without notice.

Rev: 6-4-21
GL3000 SERIES

GUIDANCE LASERS
The GL3000 Series Guidance Lasers use an ultra-high visibility green laser to establish visual line control
GL3000P GL3000PM
Remote Controlled Laser Manual Adjust Laser
• HIGWAY PAINT STRIPING V GUN CARRIAGE ALIGNMENT

V WATER BLASTER TRUCKS / RUMBLE STRIP MACHINES
/ GRINDERS

V PAVERS

V PROFILERS
For virtually any application requiring vehicle line control! LL LASERLINE MFG, INC.
1810 SE First Street, STE H. Redmond, OR 97756 •
Phone: 541-548-0882 • Email: [email protected] • Web: www.laserlinemfg.com RIAG GL3000P AUTO REMOTE SYSTEM
The driver can adjust the laser spot to the desired reference point on the road surface using the remote control panel located in the cab of the vehicle. The laser spot is impacted directly on the road surface approx. 30 feet ahead, showing the driver-operator exactly where the vehicle is relative to "on line." The laser spot is on the road ahead of the operator so that the reference is in the driving field of view instead of a T.V. screen or boom pointer.

GL3000P ADVANTAGES
It's more versatile, easier, faster and SAFER!
GL3000P-Using centerline as
• You are looking in your natural driving field of view at the reference for laser guidance reference point.
• You can reduce or eliminate pre-marking and the high cost associated with it.
• Eliminates using a boom and the problems associated with it such as bouncing on rough surfaces, safety and the mechanical size and constraint of the mechanism.
/ SAFER! Paint up to intersections without the worry of injury or damage to people or other vehicles caused by a mechanical arm extending out in front of the truck.
• Eliminates having to drive looking at a T.V. screen instead of the road. Reduces or eliminates the problem of "white-out" in low sun conditions.
• Greatly increases the machines maneuverability. You can move your reference on the fly from the cab - aim the laser spot further out, closer in, left or right.

THE GL3000P PACKAGE INCLUDES:

P/N 3000-0001 Main housing is waterproof, purged and dry nitrogen filled, contains optic plate mounting platform, microprocessor electronics, laser, laser mounting assembly, laser driver board, automatic cooling- heating system, X&Y positioning control mechanism, driver motors and optics.

P/N 3000-0008 Interconnect Control Cable: 25 foot waterproof mil spec in line connector mounted between the laser main housing and the control panel mounted in the cab.

P/N 3000-0006 Control Panel: Allows the operator to turn the unit on and off as well as aim the laser toward or away from the vehicle as well as left and right from inside the cab. Includes; 15 feet of 12 volt DC cable running from the control box for connection to 12 volt vehicle power.

P/N 3000-0435 Laser Enhancement Glasses: Cuts down on glare and enhances the visibility of the laser spot for daytime use.

P/N 3000-0080 Owner Operator's Manual (Not shown)
GL3000P SPECIFICATIONS
Laser: 532nm Class Illa Green Laser
Cable length from laser housing to control box: 25'
Power: 12 Volt DC Positive or Negative Ground
Power Draw: 4.00 Amps (Maximum Operating), 0.03 Amps (Sleep Mode) 12 Volt Power cable length from control box: 15' Laser Housing Dimensions:

Height: 7"-1/8 Shipping Weight: 25 Ibs.

Length: 11"-3/4 Enclosure Rating: Waterproof IP68
Housing Width: 6"-1/4 24 Month Warranty
Base Width: 10" Parts and Labor
Color IR Rear View Camera with Audio
WDRV-7057C-HD
•Color camera with infra-red LEDs
• Comes complete with weatherproof camera
•Sunshield
Image sensor
1/3" color SONY Super HAD (270K Pixels) SID Lens: fix 2.45mm lensF: 1.8 Effective pixels PCNZV SUmA (max 200mA)
NTSC (525TVL): 512(H) x 492(V)
PAL (625TVL): 512(H) x 582(V) Dimensions (Inch)
Scanning system 4(W) x 3.5(H) x 2.3(D)
2:1 Interlaced Weight (approx.)
H. resolution 400g (0.88lbs)
NTSC/PAL - 380TVL
Round din 6 pin or 4 pin locking type
Scanning frequency
Horizontal: 15,734Hz, Vertical: 59.94Hz
Video output level
SPECIFICATION 1.0Vp-p (750 composite)
S/N ratio
More than 50dB (AGC off)
Gamma
r=0.45
White balance
2,100°K ~ 9100°K - Auto
Min. illumination

0.5 Lux (IR LED off)
Visible Smm diameter (850nm, 30° x14ea)
Visibility range
Real 7 Meter (approx. 23 Feet)
CDS sensor
IR LED on/off at 5.0 Lux
Auto defog
Auto heater system
Operating temperature
-30°C~ +80°C (-22°F ~ +176°F)
Humidity
10% ~ 95% RH
© 2014 Weldex
6751 Katella Avenue, Cypress, CA 90630 [USA]
weldex.com
[email protected] Broichhof Strasse 5 D-40880 Ratingen, Germany [GER] el: (714) 761-2100 [US.

Fax:(714) 761-3811 [USA] WELDEX
Tel:+49 (0)2102 52B 2803 [GER]
Fax:+49 (0)2102 528 2804 (GER]
Upgrade from Black & White CRT
to Color LCD Monitor WDRV-7041M
• Weatherproof high resolution 7" TFT LCD monitor
• 3 view color monitoring system
• 1 camera inputs
• Wide range input voltage (DC12V ~ 32V)
- Selectable mirror image mode
• Anti-Glare / anti-scratch protective
lens and sunshield (option)
•OSD for AV source
(Color, brightness, contrast, tint & volume control)
• Dual compatibility for NTSC/PAL video signals
WELDEN • Integrated audio speaker
EnGE • Dot map display
• Auto scan function
• Auto power on
Screen size

7.0" (Diagonal) 5.9"
Display resolution
800(W) × 480(H)
Contrast ratio
500:1
Brightness
Max 350cd/m
Dot pitch (mm)

0.045(W) x 0.135(H)
Active area (mm)
108.0(W) x 64.8(H) WELDEX

SPECIFICATION
Viewing angle 00000000
Left 70° / Right 70° / Up 50° / Down 70°
Dimensions (Inch)

5.9"(W) × 4.9"(H)x1.3"(D) -1.3"-
Color system 1.3"

NTSC / PAL
Video output
1Vp-p (75 ohm impedance)
Connectors [7 Inch Series]
Locking cable & lead wire
Power consumption
DC12 ~ 32volt, max 7.2W
Operating temperature
-20°C~ +70°C (-4°F ~+158°F)
© 2014 Weldex
6751 Katella Avenue, Cypress, CA 90630 [USA]
weldex.com
[email protected] Broichhof Strasse 5 D-40880 Ratingen, Germany [GER) Tel: (714) 761-2100 [USA]
Fax: (714) 761-3811 [USA] WELDEX
Tel:+49 (0)2102 528 2803 [GER]
Fax:+49 (0)2102 528 2804 (GER)
SKIP-LINE® SC-12 CONTROL SYSTEM
Product Overview
The SC-12 Road Marking Vehicle Control System is the most Main
advanced skip timer on the market. Featuring a full-color, Stripe 10,0
sunlight-readable display, the SC-12 is perfect for long-line 11.0 Cycle
road marking vehicles. Exlend 10%
Ofiset -0,5 19.0 18.9
mils mils
Da Pore note Faer
The SC-12 delivers a superior operator experience by
presenting the most relevant striping information right on YELLOW AlF BEADS WITHHOLD
116
the main screen. Monitor application rates, preview a pattern before it's applied, and get system alert messages at a glance.

ADV
- SKIP-LINE
Seasoned stripers will find a similar feel and operation to previous Skip-Line systems. The new menu capabilities make START even the best crews more efficient by reducing time spent on calibration, configuration, and errors.

The SC-12 is the successor to our SM-5 legacy system, the most prevalent and recognizable skip timer in the industry.

Standard Features
Quick Setup • Pattern Preview
Start On (Index): Paint Gap • LED and Software Diagnostics Bead Guns: On Off
• Guided Calibration Procedures
Mode: Black
Counter Channels • Instant and Average Application Rates Guns Tup Pumps
Pg • High-Current Driver Outputs
Solid Skip 1/2
21(4.0): 7231
• Rugged Sealed Toggle Switches
2(4.0"): 272' 112'
14(4.0"): 0' 120° • Individual Gun Distance Offsets & On/Off Time Factor 14 (8.0"): 113' 40°
564.001
• AutoCycle and Advance/Retard
Setup
Gun Setup • Metric Unit Options
Gua Colors Gun Withs Paint Gun Offsets
Left Gun #1: Yellow • Datum Point (Delayed Start)
Left Gun #2: Yellow
• Remote Software Update Capability
Left Gun #3: White
Left Gun #4: Black
Pg Many custom & premium features available!
1/1
CALL US TODAY!
(541) 963-0111 www.skipline.com E, SKIP-LINE
SC-12 CONTROL SYSTEM

IN ACTION

EVERY ROAD MARKING VEHICLE IS UNIQUE
THE SC-12 CONTROL SYSTEM IS FLEXIBLE
ENOUGH TO WORK WITH ANY OPERATION.

Network Hub
Conveniently place hubs near SC-12 Control System devices to reduce network wiring. Hubs provide voltage dip & spike protection and ensure clean, robust communications. The network hub also shows advanced diagnostics on each device port and has LED verification of proper network operation.

Point-of-Load Driver Boxes
Place output boxes on or near carriages
to reduce wiring. Output indicators help
with installation and diagnostics. LED lights
indicate activated channels, greatly reducing
troubleshooting time. High-current driver
outputs with short circuit protection eliminate
the need for relays.

SC-12 Master (switchbox)
An SC-12 Master provides operator stations with system
control. Command the road marking operation with 0000
industry-familiar toggle switch functions. Change pattern configuration and custom settings using a simple navigation menu.
• Copyright 2021 Skip-Line, LLC. All Rights Reserved.

Core Skipper
The Core Skipper calculates and implements the striping pattern as dictated by the operator. This dedicated hardware ensures the most accurate striping at any speed.

THE
US

I SKIP-LINE
PHONE: 541.963.0111 | EMAIL: [email protected] | WEB: www.skipline.com CRPB-818 Remote Trigger Quick Start T, SKIP-LINE
VERY "HANDY" WHEN
Avoid operator fatigue when retracing with the CRPB-818 Rework PRECISION Remote Trigger. The ergonomic design significantly reduces strain IS CRITICAL over flipping toggles when repainting inconsistent skips.

Remote Trigger Functions
• The activity light will blink steadily at 1/2 second intervals when there is CAN activity.

MAICAL
• The left/right switch allows you to quickly and easily toggle the remote between controlling the right side guns and the left side guns. • Semi-Auto allows the operator to paint one full stripe length with one pull and release of the trigger.
© Note: When paired with Align Solids, Semi-Auto mode will withhold solid guns until the first trigger press.

Off will disable the remote.

Manual allows the operator to pull and hold the trigger to achive full control of all guns in SKIP.

The trigger allows for easy and comfortable operator control.

Console Installation Start/Stop Capabilities
The CRPB-818 Remote Trigger can be plugged directly into Alternatively, you may use the CRPB-818 as a way to the BUS-012 or Core Hub. If your hub is in a difficult to reach start or end an entire pattern, not just individual skips. location, you can use a 13/16" drill bit or a d-punch to create a Turn the Remote Start to ON in the Quick Setup menu mounting hole on the side of your console to allow for easier to control the start and stop points of the pattern just plug and play. Simply connect your coupler to your hub with like using the Start/Stop switch. a Cat cable.

Quick Setup
Profile On Off
HUB Remote Start On Off
Remote Trigger Seni
Plug into
any 1-8 port
207
CATS
• Semi, click the trigger to start, and click again to stop.

CONSOLE INTERIOR
Manual, start is on while the trigger is held.
• Auto, normal painting, ignores the remote trigger.
• RJ45 Panel Mount Coupler
FOR MORE DETAILED INFORMATION PLEASE REFER TO MANUAL.

Skip-Line is a registered trademark of Skip-Line, LLC., for pavement marking controls and related products & services.
, SKIP-LINE®
bY SPEC-RITE
Accessories:

Speedometer/Counter:

Remote speedometer/counter, commonly called "speedo" for driver use • CSPD-712 - Simple, large-digit speed readout
CSPD-712
MONE

CERTAL CO A KG

ODOMETER
6281
Pg. 1/13
SITE

EZLINER
& Bark
Clark A DIVISION OF VTS
Vehicle Intercom System
Modular Design - Rugged and serviceable. Reduces downtime or module replacement, cost effective.

Weather Tight - All system components are designed for use in severe weather. All modules are manufactured using rugged, heavy gauge, polycarbonate (-80°F to +212°F) housings with integral mounting feet.

Industry Standard - In use by thousands of emergency service departments, an extremely versatile "workhorse" able to accommodate most vehicle and system design requirements.

U3800: Master Station (installed in chassis cab)

TECHNICAL DATA
Heavy-gauge polycarbonate (-80°
to +212°F
included
Weight 28.5oz. /808g
Dimensions 8-%L × 5-% W × 4-40
H3492: Headset-Mic

TECHNICAL DATA
Worm cord 9.4oz./266g
B' extended coil cord, with %
hertified NRI
(3 party
Dome Type Lightweight, ABS composite
Hardware Carbon steel, chrome finish
Ear Impedance 3000
Ear Sensitivity 900B SPL re 1mW@ 1KHZ
Ear Freq Response
Mic Impedance 1502 nominal
Mic Sensitivity 400mV+/-6dB into 1502 load
@ 1kHz for 114 dB SPL input
8-16V, 4702., not polarity
U3801: Remote Headset Station (installed at rear operator position)

TECHNICAL DATA
over Regiments 12 or 24 VDC (via U3800)
o ay gauge polycarbonate (-80°
Volume Control
Headset interface
System Connection
Installation
included)

9.2oz. /261g
H3432: Headset-Mic

TECHNICAL DATA
Neigh
stereo plug.

Certified NRR 23 dB
(3" party)
Dome Type
Hardware
Ear Impedance
Ear Sensitivity 90d8 SPL re 1m@ 1kHz
Ear Freg Response 200-5,500 Hz
Mic Impedance 500 nomir
Mic Sensitivity 00mv+/-5dB into 1500 loa
@ 1kHz for 114 dB SPL input
ic Freq Respons 300-3,500 Hz
ic DC Supply 8-16V, 4700, not polarity
U3802: Remote Headset Station (installed at rear operator position)

TECHNICAL DATA
Power Requirement 12 or 24 VDC (via U3800)
Enclosure To +212 auge polycarionate (-80%
Volume Control
Headset Interface
system Connectior
nstallatio
included)
Welght 11.6oz/329g
Dimensions 5-3/8 L x 4-% W×30
H3432: Headset-Mic

TECHNICAL DATA
Neight 14.1 oz/400 g
omm Cor ' extended coil cord, with
stereo plug
stified NI 23 dB
(3 party
Hardwar Carbon ste, some inste
Ear Impedance 000 each. wired in serie
Ear Sensitivit
Ear Freq Response 200-5.500 Hz
Mic Impedance 150m to as into 150n load
Mic Sensitivity
@ 1kHz for 114 dB SPL input
Mic Freq Response 300-3,500 Hz
Mic DC Supply V. 8-16V, 4700, not polarity
raphone Coral sensitive
On/off switch, SPDI
L31 & L32 Series
5YR 332 CLASS
ISOLO
Features available across product family. May not apply to every model. *Please contact Whelen for specific photometric information regarding CA Title 13 lighthead and configurable lightbar product conformance. i Spares as Santons
L31HAF L32LAF

FEATURES
•Super-LED® beacon •Alternately or simultaneously flash multiple patterns •Powder-coated die-cast base with up to 8 Whelen Super-LED 360° beacons • Conformal coated electronics for moisture and vibration (permanent mount) resistance •Smooth polycarbonate outer dome
• Virtually no RFI/EMI radiation
Model Mount Profile | LED Color Amps VDC Patterns Control Compliance Dimensions L31H F Permanent Hi/Low Control
L31H*M Amber
Magnetic 12
or SAE
L31H V Magnetic/ White Class 1
Suction
L31HAF4 24 Permanent Mount
Permanent 4.0/Peak, 69 Built-In Hi/Low Control 4" (102mm) H x L31HAFCA High Scan-Lock™ Flash

1.6/Avg 7.19" (182mm) Dia.

L31HAMCA Magnetic Amber Patterns Plus
CA T13
Magnetic/ 4 Simulated
L31HAVCA 12
Suction Rotating Patterns
L31HMF Amber/Blue
L31HPF Permanent Amber/Green Magnetic Mount
SignalAlert" 75
L32L'F Only Hi/Low Control
Amber SAE
L32L'M Magnetic
or Class 1 2.63" (67mm) x
Low 2.O/Peak, 24
Magnetic/ White 0.8/Avg 7.19" (182mm) Dia.

L32LV
Suction
L32LAF4 Permanent Amber Hi/Low Control
a use of a magnetic or suction mounted beacon on the roof of a vehicle in motion Is not recommended, and is at the sole discretion and risk of the u sult current price list for full list of available options at whelen com/literat

OPTIONS
MIRROR20 Mirror BBKT30 L360BGB L360PMKT
Mount Bracket Shelf Mount Bracket Branch Guard Pipe Mount Kit 6 WHELEN
WARNING: This product may contain chemicals known to the State of Califor MANUFACTURED IN AMERICA cause cancer and birth defects or other reproductive harm. For mo information, visit whelen.com/regulatory.

ION™ V-Series™
Features available across product family. May not apply to every model.

Above: ION V-Series profile
Below: IONSV profile (for comparison)

IONSVIA

IONSVIC

FEATURES
•Available in 3-in-1 combination warning, spotlight, and ground •Black, White, or Chrome housing illumination light or in single-color warning-only models •Available with Smoked lenses •Single-color models have combination 180° and TIR™
directional warning
Model Technology Mount LED Color Housing Amps VDC Patterns Compliance Dimensions IONV3* Universal Black Surface Mount:

IONSV3* Amber or Black
Linear 5.94" (150mm) Wx
White with White Warning .77 33 Scan-Lock™
IONSV3"W Super-LED® Surface White 1.69" (43mm) H x
Illumination Alley. 31
IONSV3*C Chrome SA Class 1 250mm D
Ground 12
IONV1" Universal Black R65 Class 1 Universal mount:

Linear and TIR Illumination
IONSV1* Black .12 4.06" (104mm) W x
Super-LED with Amber or White 25 Scan-Lock
Directional Light Surface 1" (25mm) Hx
IONSV1°C Chrome 2.189" (56mm) D
•• • Replace symbol in model number with letter indicating desired color: A=Amber, C=White Consult current price list for full list of available options at whelen. com/literature

OPTIONS
IONK1B IONGROM IONBKT1 IONBKT5
Swivel Mount Bracket Grommet Mount Bracket License Plate Bracket Universal Mount, Reversed 52 WHELEN

MANUFACTURED IN AMERICA

EZLINER

A DIVISION OF VTS
WHELEN®
IONSVIA Lighthead
• V-Series Surface Mount -Black housing includes flange • Single Color, Amber 180° wide-angle warning light
• 12 VDC, draws 1.147 amps (avg)
Size: 1.69" (43mm) H × 2" (50mm) D × 5.94" (150mm) L
California Title 13 compliant
Accept no exceptions or equals!
Descriptive, Not Restrictive. EZ-Liner's continuing quest for improvement make equipment, specifications, and components subject to change without notice.

EZLINER

A DIVISION OF VTS
Electric Gun Elevator/Actuator
• Bearing Grade stainless steel constructed 1/2" diameter round L shaped gun holding rod • Stainless steel block slide bearing support
• Lightweight aluminum shield protecting the vertical shaft from overspray • (2) adjustable 2 ½" long handle aluminum cam lever positional locks • Dependable DC 12 V cylinder with a 6" stroke and 100 lb. load capacity • Slim design for easy adjustment of line widths (paint and bead gun compatible) • Stable and secure slide tube for vibration resistant operation v Gun raiser switch controls in gun controller boxes
Stripe:

40.0 0.0
Extend (
Ollset 0.0 14.9 9.8

EZ-LINER
Accept no exceptions or equals!
Descriptive, Not Restrictive. EZ-Liner's continuing quest for improvement make equipment, specifications, and components subject to change without notice.

NATIONAL
signal incorporated
Directional Display
Arrow Board Series

ABOUT OUR SIGN
The Directional Display™ Panel from National Signal provides advance warning and directional information.

The system assists in diverting and controlling traffic around construction or maintenance activities.

Features Applications
Powered by 12VDC with manual and automatic
dimming TRAFFIC
an be easily maneuevered, set up an
Meets the MUTCD ontrolled to work effectively in most traffic setting Rent operator control with touch sensitive CONSTRUCTION fitting option for construction conditior
here reliable messaging is neede
LED mode display
MINING
• Rugged construction
Works well, both in function and sustainability
in many mining scenarios
Automotive style fuse w/ spares
• Built-in battery indicator w/ auto shut down protects UTILITIES vehicle battery from discharge
Multipurpose us for wite organizations that
V Slimline control saves valuable dash space

SECURITY
Available in wireless Ideal for temporary locations
2440 Artesia Avenue • [email protected]
Access our website by
Fullerton, CA 92833 @ www.nationalsignalinc.net
United States of America scanning our QR code
1-888-994-0300
• SCAN ME
Display Panel
Control System
> The front and back panels are made from aluminum.
> Sealed, touch sensitive membrane switches
Perimeter frame and internal vertical members
> Power ON/OFF with LED indicator manufactured from extruded aluminum channel. > Manual/Automatic dimming
> Lamps are 4 in. amber, PAR 36 LED high brightness/low > Automotive style fuses (20A) with extra replacements power with three indicator lamps located on the rear; 5 in. > LED display on control indicates mode PAR 46 lamps for 48 x 96 panels > LED battery condition indicator > Lamp hoods (retainers) are formed of high impact plastic > Built-in low voltage shut-off protects from excessive with three indexing mounting holes; four indexing holes battery discharge for PAR 46 lamps
> Test mode illuminates all lamps allowing user to spot > Panels are etched, painted, and baked using non glare burned out lamps black powder paint. A photo resistor is built into the bottom > Remote keypad: 3"x 7.5"x 1" of the panel to measure the ambient light. > Main control: Under seat or remote location
Cables
Automatic/Manual Dimming
> Standard power cable is 9: Standard control cable is 15:
> Full lamp voltage above approximately 100 foot candles. Other cable lengths are optional.

Below 20 foot candles, lamp voltage set by photo cell > Multi-conductor with abrasion resistant jacket located under the panel to protect from vehicle head lights, street lights, etc. Lamp intensity is set by ambient light conditions.

Electric Lift
> Four manual brightness settings
> 12VDC high torque motor with automatic clutch
Panel Size Number of Lamps
24x48 13
30 x 60' 15,25
'Optional; Available in
power lift fold down version
36x721 15,25 optional double face panels
available on some models.
48 × 96 15,25
36×72180° 15,25
Specifications subject to change any time without notice. Copyright 2021 National Signal, inc. All rights reserved. Printed in the United States. 2440 Artesia Avenue [email protected]
Fullerton, CA 92833 Access our website by
www.nationalsignalinc.net
United States of America scanning our QR code
1-888-994-0300

C SCAN ME
-133 WHEELBASE

TOOLBOX
18X18X24

NHITE SS GALLON

HIGH BACK SEAT

MOUNTED ON A

AIR RIDE SUSPENSION
GERRY OVER A 88
YELOW 55 GALLON C

DRUM WITH

AGITATOR
18X1824
LETHAFCA L31HAFCA
56- 29- -180-
-296 ‡ 4 OVERALL ARROWBOARD UP
312 + 4 OVERALL ARROWBOARD DOWN-

ESTIMATED WEIGHT DISTRIBUTION FEDERAL PROPRIETARY

EMPTY FULL RATED BRIDGE
FRONT 5,109 5,758 6,630 20,000
REAR 5,188 7,540 11,020 20,000
TOTAL E LINER®
10,297 13,298| 14,500 40,000
drawn
CHECK YOUR STATE LAWS FOR STATE WEIGHT CAB ORANGE CITY, IOWA 5104] LIMITS AS THEY VARY BY STATE date createc SANTA CLARITA 2024 2/1/24 MODEL TS-AL150
date revised
- PROPOSED COMPONENT LAYOUT
-133 WHEELBASE -42 AF-
26 61 CLEAR.

CLEAR
IONSVIA →

TOOLBOX
18X18X24

BATTERY
FUEL
00 c
TANK
1001824

IONSVIA-
87 26

CLEAR CLEAR

PROPRIETARY
EZLINER®
drawn
CAB ORANGE CITY, IOWA 51041
date created SANTA CLARITA 2024
2/1/24 MODEL TS-AL150
date revised

PROPOSED COMPONENT LAYOUT
2024 ISUZUŃSÈRIES CĄS
ISUZU
ISUZU
ISUZU

ISUZU ISUZU ISTATE ISUZU TRUCK SIOUX FALLS
TRUCK TRUCK Nicholas Maltaverne | 605-310-5734 | [email protected] 2024 NPR HD GAS STOCK (2024 NPR-HD Gas Cab Chassis, 1F2 132.5"WB, 110"CA, 14,500 GVWR.

White, Standard model specifications with power windows and door locks Weight Distribution
CA Driver/Passenger Weight 350.0 Ibs.

BOC Wheelbase (WB) 132.5 inches
Cab-to-Axle (CA) 110 inches
Body Length
Body Weight
Back of Cab (BOC) 7.7 inches
** You must fill in body length and weight to enable body and payload weight calculations.

Weight (lbs.) Front Rear Total
WB Chassis 3,528.00 2,105.00 5,633.00
Chassis Equipment 19.00 0.00 19.00
Front Wt. 3,897.00 lbs. 65% Subtotal 3,547.00 2,105.00 5,652.00 Rear Wt. 2,105.00 Ibs. 35% Driver/Passengers 350.00 0.00 350.00 GVWR 14,500.00 Ibs. Body/Body 0.00 0.00 0.00
Equipment
6,002.00 Ibs. Payload 0.00 0.00 0.00
Remaining Payload Weight 8,498.00 Ibs. Total 3,897.00 2,105.00 6,002.00 GAWR/GWR 6,630.00 11,020.00 14,500.00
GOWR 20,500.00
Chassis Equipment:

Center of Front Rear
Code Item Gravity Axle Axle Total
04 White, Standard model specifications with power windows and door locks 0.00 Ibs. 0.00 Ibs. . 0.00 Ibs.

IF6 on crewinguisher and Triangle kit mounted in rear organizer on standard cab and under rear seal 19.00 Ibs. 0.00 lbs. 19.00 Ibs.

Driver/Passengers:

Center of Gravity Front Axle Rear Axle Total
Driver front axle 350.00 Ibs. 0.00 Ibs. 350.0 Ibs.

Current report content is based on data as of 2022-10-28 06:25:47. Any performance-related calculations are offered solely as guidelines. Actual vehicle

Page 2 ends

ISUZU ISUZU ISTATE ISUZU TRUCK SIOUX FALLS
TRUCK TRUCK Nicholas Maltaverne | 605-310-5734 | [email protected] 2024 NPR HD GAS STOCK (2024 NPR-HD Gas Cab Chassis, 1F2 132.5"WB, 110"CA, 14,500 GVWR.

White, Standard model specifications with power windows and door locks Selected Model and Options
Code Description Weight
Model
1F2 NPR-HD Gas Cab Chassis 132.5"WB, 110"CA
04 White, Standard model specifications with power
windows and door locks
Vehicle Application
RQ2 Truck Application 0.0 Ibs.

Tires
I5H LRR (low rolling resistance) 0.0 Ibs.

Engine
L8T GMPT 6.6L (400 CID) V8 gasoline engine; 350 HP at 0.0 Ibs. 4500 RPM; 425 Ib-ft torque at 3800 RPM; precise
fuel control direct injection technology; electronic
throttle control; overhead valves with variable valve
timing; heavy duty cast-iron cylinder block with six-
bolt main-bearing cap; cast aluminum cylinder
heads; forged steel crankshaft; stainless steel
exhaust manifold.

Transmission
MYD 6L90-E Hydra-Matic, 6-speed automatic with lock-up 0.0 Ibs. converter and overdrive. Ratios: Gear and Ratios

4.027, 2.364,1.532, 1.152, 0.0852, 0.667, Rev.

3.064:1
Wheelbase
1A9 132.5 inches, includes ladder type channel frame. 0.0 Ibs.

Full C section straight frame 33.5 inches wide. Yield
strength 44,000 psi; section modulus 7.20 in3 RBM
316,800 Ib./ft./in. per rail. 110"CA
Air Cleaner
KNX Dry paper single element. Air cleaner canister 0.0 Ibs. standard with air restriction gauge.

Alternator
KW7 170 Amp. output with integral regulator. 0.0 Ibs.

Battery
IL3 Single Delco 12-V maintenance free 750 CCA frame 0.0 Ibs. mounted battery box
Exhaust
141 Single horizontal aluminized steel with catalytic 0.0 Ibs. converter and oxygen sensor devices.

Front Axle
ID2 ""-beam rated at 6,830 Ibs. Includes integral 0.0 Ibs. hydraulic power steering. Ratio 18.8-20.9:1.

Front Suspension
ID4 6,830 Ib. capacity. Semi-elliptical tapered leaf 0.0 Ibs. springs. Includes shock absorbers and stabilizer bar.

Front Wheels
1B9 19.5" x 6", 6-hole disc, painted white 0.0 Ibs.

Front Tires
18B 225/70R19.5G (14 ply) tubeless Radial, all season 0.0 Ibs. tread
Current report content is based on data as of 2022-10-28 06:25:47. Any performance-related calculations are offered solely as guidelines. Actual vehicle performance will depend on your operating conditions. All Information, specifications and pricing in this application are based on the latest information vailable. Isuzu Commercial Truck of America, Inc. reserves the right to discontinue or change, at any time, without prior notice, the pricin pecifications, options, materials, equipment, design and model

Page 3 ends

ISUZU ISUZU ISTATE ISUZU TRUCK SIOUX FALLS
TRUCK TRUCK Nicholas Maltaverne | 605-310-5734 | [email protected] 2024 NPR HD GAS STOCK (2024 NPR-HD Gas Cab Chassis, 1F2 132.5"WB, 110"CA, 14,500 GVWR.

White, Standard model specifications with power windows and door locks Selected Model and Options
Code Description Weight
Rear Suspension
18J 12,900 Ibs. Capacity semi elliptical; main and 0.0 Ibs. auxiliary multi- leaf spring. Includes shock absorbers.

Rear Axle
ID3 Single-speed, 14,550 Ib. capacity with oil lubricated 0.0 Ibs. rear wheel bearings.

Ratio
092 4.300:1 0.0 Ibs.

Rear Wheels
IC1 19.5" × 6", 6-hole disc, painted white 0.0 Ibs.

Rear Tires
19B 225/70R19.5G (14 ply) tubeless Radial, all season 0.0 Ibs. tread.

Fuel Tank
A17 38.6 gal. rectangular fuel tank. Mounted between 0.0 Ibs. frame rail with electric type fuel pump (mounted in
tank). Through the rail fuel fill.

Seat
AQB Driver seat is reclining high back. Two single 0.0 Ibs. occupant fold down seats with tray backs.

Brakes
1E1 Vacuum + Power Assist; hydraulic 4-wheel disc 0.0 Ibs. brakes with 4-channel ABS. Mechanical.
transmission mounted parking brake. Non-asbestos
semi metallic linings are standard.

Air Conditioning
C60 Air conditioner 0.0 Ibs.

Power Windows & Door Locks
ILO Yes 0.0 Ibs.

Model Option
04 White, Standard model specifications with power 0.0 Ibs. windows and door locks
Additional Options
1F6 Fire Extinguisher and Triangle Kit mounted in rear 19.0 Ibs. organizer on standard cab and under rear seat on
crew cab
Accessories
1x2 Rear body dome lamp switch 0.1 Ibs.
8RP AM/FM/CD radio with Aux input/USB port and 0.0 Ibs.

Bluetooth RPO
Current report content is based on data as of 2022-10-28 06:25:47. Any performance-related calculations are offered solely as guidelines. Actual vehicle performance will depend on your operating conditions. All Information, specifications and pricing in this application are based on the latest information vailable. Isuzu Commercial Truck of America, Inc. reserves the right to discontinue or change, at any time, without prior notice, the pricing specifications, options, materials, equipment, design and model

Page 4 ends

ISUZU ISUZU ISTATE ISUZU TRUCK SIOUX FALLS
TRUCK TRUCK Nicholas Maltaverne | 605-310-5734 | [email protected] 2024 NPR HD GAS STOCK (2024 NPR-HD Gas Cab Chassis, 1F2 132.5"WB, 110"CA, 14,500 GVWR.

White, Standard model specifications with power windows and door locks Standard Equipment Summary
Code Description
Vehicle Application
RQ2 Truck Application
Tires
15H LRR (low rolling resistance)
Engine
L8T GMPT 6.6L (400 CID) V8 gasoline engine; 350 HP at 4500 RPM; 425 Ib-ft torque at 3800 RPM; precise fuel control direct injection technology; electronic throttle control; overhead valves with variable valve timing; heavy duty cast-iron cylinder block with six-bolt main-bearing cap; cast aluminum cylinder heads; forged steel crankshaft; stainless steel exhaust manifold.

Transmission
MYD 6L90-E Hydra-Matic, 6-speed automatic with lock-up converter and overdrive. Ratios: Gear and Ratios 4.027, 2.364, 1.532,

1.152, 0.0852, 0.667, Rev. 3.064:1
Wheelbase
1A9 132.5 inches, includes ladder type channel frame. Full C section straight frame 33.5 inches wide. Yield strength 44,000 psi; section modulus 7.20 in3 RBM 316,800 lb./ft./in. per rail. 110"CA Air Cleaner
KNX Dry paper single element. Air cleaner canister standard with air restriction gauge.

Alternator
KW7 170 Amp. output with integral regulator.

Battery
IL3 Single Delco 12-V maintenance free 750 CCA frame mounted battery box Exhaust
141 Single horizontal aluminized steel with catalytic converter and oxygen sensor devices.

Front Axle
ID2 "I'-beam rated at 6,830 Ibs. Includes integral hydraulic power steering. Ratio 18.8-20.9:1.

Front Suspension
ID4 6,830 Ib. capacity. Semi-elliptical tapered leaf springs. Includes shock absorbers and stabilizer bar.

Front Wheels
1B9 19.5" × 6", 6-hole disc, painted white
Front Tires
18B 225/70R19.5G (14 ply) tubeless Radial, all season tread Rear Suspension
18J 12,900 Ibs. Capacity semi elliptical; main and auxiliary multi- leaf spring. Includes shock absorbers.

Rear Axle
ID3 Single-speed, 14,550 lb. capacity with oil lubricated rear wheel bearings.

Ratio
092 4.300:1
Rear Wheels
IC1 19.5" × 6", 6-hole disc, painted white
Rear Tires
19B 225/70R19.5G (14 ply) tubeless Radial, all season tread.

Fuel Tank
A17 38.6 gal. rectangular fuel tank. Mounted between frame rail with electric type fuel pump (mounted in tank). Through the rail fuel fill.

Seat
AQB Driver seat is reclining high back. Two single occupant fold down seats with tray backs.

Brakes
1E1 Vacuum + Power Assist; hydraulic 4-wheel disc brakes with 4-channel ABS. Mechanical, transmission mounted parking Current report content is based on data as of 2022-10-28 06:25:47. Any performance-related calculations are offered solely as guidelines. Actual vehicle performance will depend on your operating conditions. All Information, specifications and pricing in this application are based on the latest information avalable. suzu Commercial Truck of Americations: estons, thaterase duiment, or an and madany time, without prior notice, the pricing.

Page 5 ends

ISUZU ISUZU ISTATE ISUZU TRUCK SIOUX FALLS

TRUCK TRUCK
Nicholas Maltaverne | 605-310-5734 | [email protected] 2024 NPR HD GAS STOCK (2024 NPR-HD Gas Cab Chassis, 1F2 132.5"WB, 110"CA, 14,500 GVWR.

White, Standard model specifications with power windows and door locks Standard Equipment Summary
Code Description
brake. Non-asbestos semi metallic linings are standard
Air Conditioning
C60 Air conditioner
Power Windows & Door Locks
Model Option
04 White, Standard model specifications with power windows and door locks Accessories
IX2 Rear body dome lamp switch
8RP AM/FM/CD radio with Aux input/USB port and Bluetooth RPO Current report content is based on data as of 2022-10-28 06:25:47. Any performance-related calculations are offered solely as guidelines. Actual vehicle performance will depend on your operating conditions. All Information, specifications and pricing in this application are based on the latest information available. Isuzu Commercial Truck of America, Inc. reserves the right to discontinue or change, at any time, without prior notice, the pricing, specifications, options, materials, equipment, design and models.

Page 6 ends

EZ-LINER LIMITED WARRANTY
EZ-Liner warrants all equipment manufactured by it and bearing its brand names to be free from defects in materi and workmanship at the time of sale by EZ-Liner or an authorized EZ-Liner distributor. EZ-Liner will for a period or twelve months from the date of sale, repair or replace any part of the equipment proven defective. Repair or replacement under this warranty shall be purchaser's sole remedy for breach of the warranty. Products furnished by but not manufactured by EZ-Liner (such as chassis, engines, compressor, etc.) will carry only the warranty of the original equipment manufacturer.

In addition, EZ-Liner extends this warranty to weight or load bearing major structure, not including the chassis, for an additional 48 months from the date of sale. EZ Liner warrants the major structure will be free from defective workmanship or materials. EZ-Liner will repair, reinforce or replace defective structural elements originally manufactured by EZ Liner for an additional 48 months from the date of sale. After the initial 12 months from date of sale, the costs of repair, reinforcement or replacement shall be prorated* for the remaining 48 months.

This warranty shall not apply if the product has been subject to misuse, negligence, accident or tampering or has not been operated in accordance with EZ-Liner's recommendations. This warranty does not cover and EZ-Liner shall not be liable for any damage, wear or malfunction caused by improper or inadequate maintenance, or substitution of components not supplied by EZ-Liner. Warranty does not apply to normal wear and tear due to equipment operation or to consumable replacement parts.

This warranty applies only to the original purchaser and only when the equipment is operated and maintained in accordance with EZ-Liner's written recommendations or instructions. Purchaser must, with transportation prepaid, return the equipment claimed to be defective to EZ-Liner for verification of the claimed defect. If the alleged defect is verified, EZ-Liner will, at EZ-Liner's option, repair or replace any defective parts. The equipment will be returned including prepayment of transportation charges to the original purchases. Expedited fees will be paid by the customer if requested. If no defects in material and workmanship are found, repairs will be made by EZ-Liner at a reasonabl charge. Charges may include the cost of parts, labor and freight.

EZ-LINER DISCLAIMS TO THE FULL EXTENT PERMITTED BY LAW ALL WARRANTIES, EXPRESSED

OR IMPLIED INCLUDING ANY WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR

A PARTICULAR PURPOSE AND ANY NON CONTRACTUAL LIABILITIES INCLUDING PRODUCT LIABILITY BASED ON NEGLIGENCE OR STRICT LIABILITIES. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION OF THE FACE HEREOF.

Every form of liability is expressly excluded and denied for direct, indirect, special or consequential damages or loss.

The warranty shall be in lieu of any other warranty expressed or implied. The terms of this warranty constitute purchaser's sole and exclusive remedy. In no case shall EZ-Liner liability exceed the amount of the purchase price.

Any action for breach of warranty must be brought within one (1) year of the date of sale or in service date.

The following list is intended to act only as an example of these warranties, which are subject to change without notice but may not be limited to only the following:

Industrial/Commercial engines carry a one year limited warranty Air compressors carry a one year limited warranty
ASME pressure pots are pressure tested, certified and carry a one year limited warranty Bead guns carry a one year limited warranty
Hydraulic pumps carry a one year warranty
Paint pumps carry a one year limited warranty
Paint guns carry a one year limited warranty
Air solenoids carry a one year warranty
Electronic controllers carry a one year limited warranty For a list of wearable items, see AD-0002-DOC - EZ-Liner Warranty-Wearable Parts. *Structural Coverage: Months12- 24- 80% ; Months 25-36- 60%; Months 37-48-40%; Months 49-60- 20% over 60- no coverage AD-0001-DOC, Rev B -EZ-Liner Warranty 8/1/21

Santa Clarita City CouncilAugust 27, 2024

Santa Clarita City Council
August 27, 2024