Torrance City Council
February 25, 2025

8C
Date: February 25, 2025
To: Honorable Mayor and Members of the City Council
From: Kimberly Turner, Transit Director
By: Art Estrada, Fleet Services Manager | [email protected] Subject: Transit – Authorize Purchase Order for New and Remanufactured Bus Repair Parts.

Expenditure: Not-To-Exceed $1,800,000 (Non-General Fund: $600,000 annually).

RECOMMENDATION
Recommendation of the Transit Director that City Council authorize a sole-source purchase order to Aftermarket Parts CO LLC DBA New Flyer Parts of Manitoba, Canada for an amount not-to-exceed of $1,800,000 ($600,000 annually) to furnish new and remanufactured bus parts and components on an as needed basis for a three-year period beginning February 21, 2025 and ending February 20, 2028.

FUNDING
Funding is available in the fiscal year 2024-2025 Transit Department operating budget and is anticipated to be available in subsequent fiscal years.

DISCUSSION
The Transit Department’s Fleet Services’ Warehouse provides repair parts for the Transit’s bus fleet. Typically, using only NFI Parts’ OEM bus parts and components to maintain the City’s bus fleet, as they are the patent holder and sole-source vendor. Parts are stocked on a continual basis so that maintenance issues can be immediately addressed without adversely affecting daily bus service and revenue.

The Transit Warehouse continues to experience a high demand for OEM parts due to the age of the current fleet. Our bus fleet consists of vehicles with model years: 2010, 2011, 2012, and 2016.

Therefore, placing our vehicles life span between 15 to 9 years, increasing our risk of major component repairs. Additionally, our high demands for OEM parts are due to vehicle warranty expirations and the overall cost of maintaining an alternative fueled transit bus fleet. The division’s goal is to maintain all buses up to par in order to participate in our future 2026 World Cup and 2028 Olympics.
1 City Council
February 25, 2025

A Sole-Source Purchase is allowable under Torrance Municipal Code Section 22.3.100 (b) EXCEPTIONS TO THE COMPETITIVE PROCESS, which states:
(b) Competition does not reasonably exist because only one vendor possesses the unique ability or capability to meet the particular requirements of the solicitation, such as when a good or service is copyrighted, patented or otherwise only available from one license holder, including, for example, proprietary goods of original equipment manufacturers and/or their authorized exclusive distributors. No sole-source purchases may be made where to do so would show favoritism, improvidence, extravagance, fraud or corruption, or result in the waste of public funds, but may be used to only obtain the best economic result for the public.

ATTACHMENTS

1. New Flyer Bus Parts Single Source Affidavit

2. Federal Transit Administration (FTA) Clauses Signed by Vendor

3. New Flyer’s Price Listing

4. Procurement Request Form
2 December 23, 2024
City of Torrance

Subject: Single Source Affidavit of New Flyer Bus Parts

Dear Customer,

The Aftermarket Parts Company branded as NFI Parts is the O.E.M. supplier of customized heavy -duty coach / transit bus parts for the NFI Group Inc branded coaches/buses. Many customized components such as body/chassis, suspension, windows, tubes/ hoses etc. are either manufactured by NFI Parts or procured from vendors under proprietary agreements and specifically manufactured from NFI Group Engineering drawings.

Such procured/manufactured parts can only be purchased from NFI Groups Aftermarket Parts organiz ation, “The Aftermarket Parts Company” branded as NFI Parts.

Our proprietary vendor agreements strictly limit the sale of these items to and through the OEM bus manufacturers NFI Group only. The manufacturing process for said coach body/chassis, suspension, windows, tubes / hoses etc. is unique and critical to NFI Group branded coaches/buses and not utilized by any other coach/bus OEM. No other aftermarket parts distributor would have availability of these proprietary items making NFI Group Inc’s Aftermarket Parts Company branded as NFI Parts the single source for t hese parts.

Thank you for your interest in NFI Parts. If you have any questions or concerns, please do not hesitate to contact Jim Wacker or myself at 1-800-665-2637.

Sincerely,

Eric Bosh
Customer Service Representative
NFI Parts

3 ATTACHMENT 1

Rev. 02/2023 FTA Master Agreement dated November 2, 2022

FEDERAL TRANSIT ADMINISTRATION (FTA) CLAUSES

(Revised 02/2023)

Contractor shall comply with the following FTA requirements. For purposes of these clauses, the AGENCY is the FTA recipient or subrecipient that is entering the Contract with Contractor.

1. NO FEDERAL GOVERNMENT OBLIGATION TO THIRD PARTIES. [These requirements do not apply to micro -purchases ($10,000 or less, except for construction contracts over $2,000).]

The AGENCY and Contractor acknowledge and agree that, notwithstanding any concurrence by the Federal Government in or approval of the solicitation of this Contract, absent the express written consent by the Federal Government, the Federal Government is not a party to this Contract and shall not be subject to any obligations or liabilities to the AGENCY, Contractor or any other party (whether or not a party to that Contract) pertaining to any matter resulting from the Contract. Contractor shall include the above clause in each subcontract financed in whol e or in part with Federal assistance provided by the FTA. It is further agreed that the clause shall not be modified, except to identify the subcontractor who will be subject to its provisions.

2. NOTIFICATION TO FTA. [These requirements apply to all contracts and subcontracts in excess of $25,000.]

If a current or prospective legal matter that may affect the Federal Government emerges, Contractor must promptly notify the AGENCY, which must then promptly notify the FTA Chief Counsel and FTA Regional Counsel for Region 9. Contractor must include an equivalent provision in its subagreements at every tier for any agreement that is a “covered transaction” according to 2 C.F.R. §§ 180.220 and 1200.220.

A. Types of Legal Matter s Requiring Notification. The types of legal matters that require notification include, but are not limited to, a major dispute, breach, default, litigation, or naming the Federal Government as a party to litigation or a legal disagreement in any forum for any reason.

B. Matters Affecting the Federal Government. Matters that may affect the Federal Government include, but are not limited to, the Federal Government’s interests in the Award, the Contract, and any Amendments thereto, or the Federal Government’s administration or enforcement of federal laws, regulations, and requirements.

C. Additional Notice to U.S. DOT Inspector General. Contractor must promptly notify the AGENCY, which must then promptly notify the U.S. DOT Inspector General in addition to the FTA Chief Counsel or Regional Counsel for Region 9 if Contractor has knowledge of potential fraud, waste, or abuse occurring on a Project receiving assistance from FTA. The notification provision applies if a person has or may have submitted a false claim under the False Claims Act, 31 U.S.C. § 3729, et seq., or has or may have committed a criminal or civil violation of law pertaining to such matters as fraud, conflict of interest, bid rigging, misappropriation or embezzlement, bribery, gratuity, or similar misconduct involving federal assistance. This responsibility occurs whether the Project is subject to this Contract or another agreement between the AGENCY and FTA, or an agreement involving a principal, officer, employee, agent, or Third-Party Participant of the AGENCY. It also applies to subcontractors at any tier.

Knowledge, as used in this paragraph, includes, but is not limited to, knowledge of a 4 ATTACHMENT 2

Rev. 02/2023 FTA Master Agreement dated November 2, 2022 criminal or civil investigation by a Federal, state, or local law enforcement or other investigative agency, a criminal indictment or civil complaint, or probable cause that could support a criminal indictment, or any other credible information in the possession of Contractor. In this paragraph, “promptly” means to refer information without delay and without chan ge. This notification provision also applies to all divisions of the AGENCY, including divisions tasked with law enforcement or investigatory functions.

3. PROGRAM FRAUD & FALSE/FRAUDULENT STATEMENTS OR RELATED ACTS. [These requirements do not apply to micro -purchases ($10,000 or less, except for construction contracts over $2,000).]

A. Contractor acknowledges that the provisions of the Program Fraud Civil Remedies Act of 1986, as amended, 31 U.S.C. § 3801 et seq. and U.S. DOT regulations, "Program Fraud Civil Remedies," 49 CFR part 31, apply to its actions pertaining to this Project.

Upon execution of the Contract, Contractor certifies or affirms the truthfulness and accuracy of any statement it has made, it makes, it may make, or causes to be made, pertaining to the Contract or the FTA -assisted project for which this contract work is being performed. In addition to other penalties that may be applicable, Contractor further acknowledges that if it makes, or causes to be made, a false, fictitious, or fraudulent claim, statement, submission, or certification, the Federal Government reserves the right to impose the penalties of the Program Fraud Civil Remedies Act of 1986 on Contractor to the extent the Federal Government deems appropriate.

B. Contractor also acknowledges that if it makes, or causes to be made, a false, fictitious, or fraudulent claim, statement, submission, or certification to the Federal Government under a contract connected with a project that is financed in whole or in part with Federal assistance originally awarded by FTA under the authority of 49 U.S.C. chapter 53, the Government reserves the right to impose the penalties of 18 U.S.C. § 1001 and 49 U.S.C. § 5323(l) on Contractor, to the extent the Federal Government deems appropriate.

C. Contractor shall include the above two paragraphs in each subcontract financed in whole or in part with Federal assistance provided by FTA. It is further agreed that the clauses shall not be modified, except to identify the subcontractor who will be subject to the provisions.

4. ACCESS TO RECORDS, REPORTS, & SITES.

A. Record Retention. Contractor shall retain, and will require its subcontractors of all tiers to retain, complete and readily accessible records related in whole or in part to the contract, including, but not limited to, data, documents, reports, statistics, sub - agreements, leases, subcontracts, arrangements, other third-party agreements of any type, and supporting materials related to those records.

B. Retention Period. Contractor shall comply with the record retention requirements in accordance with 2 CFR § 200.333. Contractor shall maintain all books, re cords, accounts and reports required under this Contract for a period of at not less than three years after the date of termination or expiration of this Contract, except in the event of litigation or settlement of claims arising from the performance of this Contract, in which case records shall be maintained until the disposition of all such litigation, appeals, claims or exceptions related thereto.

C. Access to Records. Contractor shall provide sufficient access to the U.S. Secretary of Transportation, the Comptroller General of the United States, FTA, the Agency, and their duly authorized representatives to inspect and audit records and information 5 Rev. 02/2023 FTA Master Agreement dated November 2, 2022 related to performance of this contract as reasonably may be required.

D. Access to the Sites of Performance. Contractor shall permit FTA, the Agency, and their duly authorized representatives access to the sites of performance under this Contract as reasonably may be required.

5. FEDERAL CHANGES. Contractor shall at all times comply with all applicable federal laws, regulations, requirements, policies, procedures, guidance, and directives, including without limitation those listed directly or by reference in the FTA Master Agreement between the City of Phoenix and the FTA, as they may be amended or promulgated from time to time during the term of the Contract. Contractor’s failure to so comply shall constitute a material breach of the Contract.

6. CIVIL RIGHTS. The AGENCY must comply with applicable federal civil rights laws, regulations, and requirements, and follow ap plicable federal guidance, except as the Federal Government determines otherwise in writing. Therefore, unless an AGENCY or federal program, including any Indian Tribe or Tribal Transit Program, is specifically exempted from a civil rights statute, FTA requires compliance with each civil rights statute, including compliance with equity in service requirements.

A. Nondiscrimination in Federal Public Transportation Programs.

1. Contractor must prohibit: (a) discrimination based on race, color, religion, national origin, sex (including sexual orientation and gender identity), disability, or age; (b) exclusion from participation in employment or a business opportunity for reasons identified in 49 U.S.C. § 5332 ; (c) denial of program benefits in employment or a business opportunity identified in 49 U.S.C. § 5332; and (d) discrimination identified in 49 U.S.C. § 5332, including discrimination in employment or a business opportunity identified in 49 U.S.C. § 5332.

2. Contractor must follow the most recent edition of FTA Circular 4702.1, “Title VI Requirements and Guidelines for Federal Transit Administration Recipients,” to the extent consistent with applicable federal laws, regulations, requirements, and guidance. However, FTA does not require an Indian Tribe to comply with FTA program specific guidelines for Title VI when administering its agreement supported with federal assistance under the Tribal Transit Program.

B. Nondiscrimination – Title VI of the Civil Rights Act. Contractor must:

1. Contractor must prohibit discrimination based on race, color, or national origin,

2. Contractor must comply with: (a) Title VI of the Civil Rights Act of 1964, as amended, 42 U.S.C. § 2000d, et seq.; (b) U.S. DOT regulations, “Nondiscrimination in Federally -Assisted Programs of the Department of Transportation – Effectuation of Title VI of the Civil Rights Act of 1964,” 49 CFR Part 21; and (c) Federal transit law, specifically 49 U.S.C. § 5332; and

3. Contractor must follow: (a) the most recent edition of FTA Circular 4702.1, “Title VI Requirements and Guidelines for Federal Transit Administration Recipients,” to the extent consistent with applicable federal laws, regulations, requirements, and guidance; (b) U.S. DOJ, “Guidelines for the enforcement of Title VI, Civil Rights Act of 1964,” 28 C.F.R. § 50.3; and (c) all other applicable federal guidance that may be issued.

C. Equal Employment Opportunity.

1. Federal Requirements and Guidance. Contractor must prohibit discrimination based on race, color, religion, sex, sexual orientation, gender identity, or national origin. Contractor must also comply with: (a) Title VII of the Civil Rights Act of 1964, as amended, 42 U.S.C. § 2000e, et seq.; (b) Title I of the Americans with 6 Rev. 02/2023 FTA Master Agreement dated November 2, 2022 Disabilities Act of 1990, as amended, 42 U.S.C. §§ 12101, et seq.; (c) Executive Order No. 11246, “Equal Employment Opportunity” September 24, 1965 (42 U.S.C. § 2000e note), as amended by any later Executive Order that amends or supersedes it in part and is applicable to federal assistance programs; (d) federal transit law, specifically 49 U.S.C. § 5332, as provided in section 12 of this Master Agreement; and (e) FTA Circular 4704.1 “Equal Employment Opportunity (EEO) Requirements and Guidelines for Federal Transit Adminis tration Recipients.” Further, Contractor must follow other federal guidance pertaining to EEO laws, regulations, and requirements.

2. Affirmative Action. If required to do so by U.S. DOT regulations (49 CFR Part 21) or U.S. Department of Labor regulations (41 C.F.R. chapter 60), Contractor must take affirmative action that includes, but is not limited to: (a) recruitment advertising, recruitment, and employment; (b) rates of pay and other forms of compensation; (c) selection for training, including apprenticeship, and upgrading; and (d) transfers, demotions, layoffs, and terminations.

3. Indian Tribe. Contractor recognizes that Title VII of the Civil Rights Act of 1964, as amended, exempts Indian Tribes under the definition of “Employer.”

4. Equal Employment Opportun ity for Construction Activities. When undertaking “construction” as recognized by the U.S. Department of Labor (U.S. DOL), Contractor must comply with: (a) U.S. DOL regulations, “Office of Federal Contract Compliance Programs, Equal Employment Opportunity, Department of Labor,” 41 C.F.R. chapter 60; and (b) Executive Order No. 11246, “Equal Employment Opportunity in Federal Employment,” September 24, 1965, 42 U.S.C. § 2000e note (30 Fed. Reg. 12319, 12935), as amended by any later Executive Order that amends or supersedes it, referenced in 42 U.S.C. § 2000e note.

7. INCORPORATION OF FTA TERMS. [These requirements do not apply to micro - purchases ($10,000 or less, except for construction contracts over $2,000).]

The preceding provisions include, in part, certain Standard Terms and Conditions required by the U.S. Department of Transportation (DOT ), whether or not expressly set forth in the preceding contract provisions. All contractual provisions required by DOT, as set forth in FTA Circular 4220.1F, and are hereby incorporated by reference. Anything to the contrary herein notwithstanding, all FTA mandated terms shall be deemed to control in the event of a conflict with other provisions contained in the contract. Contractor shall not perform any act, fail to perform any act, or refuse to comply with any requests of the AGENCY that would cause the A GENCY to be in violation of the FTA terms and conditions. Contractor shall include this clause in each subcontract financed in whole or in part with Federal assistance provided by the FTA.

8. FREE SPEECH & RELIGIOUS LIBERTY. All Federal funding must be expe nded in full accordance with the U.S. Constitution, Federal Law, and statutory and public policy requirements, including but not limited to those prohibiting discrimination and protecting free speech, religious liberty, public welfare, and the environment.

9. FEDERAL TERMINATION RIGHTS. The termination rights under this Contract are in addition to, and in no way limit, the Federal Government’s right to terminate as described in 2 CFR § 200.340.

10. DEBARMENT, SUSPENSION, INELIGIBILITY, & VOLUNTARY EXCLUSION. [This requirement does not apply to contracts and subcontracts under $25,000.] 7 Rev. 02/2023 FTA Master Agreement dated November 2, 2022

A. Contractor shall comply and facilitate compliance with U.S. DOT regulations, “Non - procurement Suspension and Debarment,” 2 CFR part 1200, which adopts and supplements the U.S. Off ice of Management and Budget (U.S. OMB) “Guidelines to Agencies on Government -Wide Debarment and Suspension (Non -procurement),” 2 CFR part 180. These provisions apply to each contract at any tier of $25,000 or more, and to each contract at any tier for a f ederally required audit (irrespective of the contract amount), and to each contract at any tier that must be approved by an FTA official irrespective of the contract amount.

B. Contractor shall verify that its principals, affiliates, and subcontractors are eligible to participate in this federally-funded contract (which includes review of SAM at sam.gov, if necessary to comply with U.S. DOT regulations, 2 CFR Part 1200) and are not presently declared by a ny Federal department or AGENCY to be: (1) debarred from participation in any federally-assisted Award; (2) suspended from participation in any federally-assisted Award; (3) proposed for debarment from participation in any federally-assisted Award; (4) declared ineligible to participate in any federally-assisted Award; (5) voluntarily excluded from participation in any federally -assisted Award; or (6) disqualified from participation in any federally-assisted Award.

C. By signing and submitting its bid or proposal, the bidder or proposer certifies as follows:

The certification in this clause is a material representation of fact relied upon by the AGENCY. If it is later determin ed by the AGENCY that Contractor knowingly rendered an erroneous certification, in addition to remedies available to the AGENCY, the Federal Government may pursue available remedies, including but not limited to suspension and/or debarment. Contractor shal l comply with the requirements of 2 CFR part 180, subpart C, as supplemented by 2 CFR part 1200, while this offer is valid and throughout the period of any contract that may arise from this offer. Contractor further agrees to include a provision requiring such compliance in its lower tier covered transactions.

11. TERMINATION. The AGENCY must include provisions in their contracts and subcontracts that allows for termination for cause and for convenience by the AGENCY, including the manner by which it will be e ffected and the basis for settlement. See Appendix II(B) to 2 CFR part 200 —Contract Provisions for Non -Federal Entity Contracts Under Federal Awards, and FTA Circular 4220.1F, Chapter IV, paragraph 2.b.(6)(b)4 – Termination.

12. VIOLATION & BREACH OF CONTRACT . [These requirements are not applicable to contracts and subcontracts under the simplified acquisition threshold (currently set at $250,000).]

Unless otherwise provided for by the AGENCY, the following provisions shall apply:

A. Dispute Resolution. Disputes arising in the performance of this Contract that are not resolved by agreement of the parties shall be decided in writing by the authorized representative of AGENCY. This decision shall be final and conclusive unless within ten calendar days from the date of receipt of its copy, Contractor mails or otherwise furnishes a written appeal to the authorized representative of AGENCY. In connection with any such appeal, Contractor shall be afforded an opportunity to be heard and to offer evidence in support of its position. The decision of the authorized representative of AGENCY shall be binding upon Contractor, and Contractor shall abide by the 8 Rev. 02/2023 FTA Master Agreement dated November 2, 2022 decision.

B. Performance During Disputes. Notwithstanding the existence of any dispute between the parties, insofar as is possible, under the terms of the Contract, Contractor shall continue to perform the obligations required of Contractor during the continuation of any such dispute unless enjoined or prohibited by an Arizona Court of competent jurisdiction.

C. Rights and Remedies. The duties and obligations imposed by the Contract documents and the rights and remedies available thereunder shall be in addition to and not a limitation of any duties, obligations, rights and remedies otherwise imposed or available by law. No action or failure to act by the AGENCY or Contractor shall constitute a waiver of any right or duty afforded any of them under this Contract, nor shall any such action or failure to act constitute an approval of or acquiescence in any breach thereunder, except as may be specifically agreed upon in writing.

13. LOBBYING RESTRICTIONS. [These requirements do not apply to contracts and subcontracts under $100,000.]

Byrd Anti-Lobbying Amendment, 31 U.S.C. 1352, as amended by the Lobbying Disclosure Act of 1995, P.L. 104 -65 [to be codified at 2 U.S.C. § 1601, et seq.] - Contractors who apply or bid for an award of $100,000 or more shall file the certification required by 49 CFR part 20, "New Restrictions on Lobbying." Each tier certifies to the tier above that it will not and has not used Federal appropriated funds to pay any person or organization for influencing or attempting to influence an officer or employee of any agency, a member of Congress, officer or employee of Congress, or an employee of a member of Congress in connection with obtaining any Federal contract, grant or any other award covered by 31 U.S.C. 1352. Each tier shall also disclose the name of any registrant under the Lobbying Disclosure Act of 1995 who has made lobbying contacts on its behalf with non -Federal funds with respect to that Federal contract, grant or award covered by 31 U.S.C. 1352.

Such disclosures are forwarded from tier to tier up to the AGENCY.

14. CARGO PREFERENCE (USE OF U.S.-FLAG VESSELS). [These requirements apply to all contracts involving equipment, material, or commodities that may be transported by ocean vessels.]

A. Contractor shall use privately owned United States-Flag commercial vessels to ship at least 50 percent of the gross tonnage (computed separately for dry bulk carriers, dry cargo liners, and tankers) involved, whenever shipping any equipment, material, or commodities pursuant to the Contract to the extent such vessels are available at fair and reasonable rates for United States-Flag commercial vessels; B. Contractor shall furnish within 20 working days following the date of loading for shipments originating within the United States or within 30 working days following the date of loading for shipments originating outside the United States, a legible copy of a rated, "on-board" commercial ocean bill-of-lading in English for each shipment of cargo described in the preceding paragraph to the Division of National Cargo, Office of Market Development, Maritime Administration, Washington, DC 20590 and to the FTA recipient (through Contractor in the case of a subcontractor's bill-of-lading); and C. Contractor shall include these requirements in all subcontracts issued pursuant to this contract when the subcontract may involve the transport of equipment, material, or commodities by ocean vessel.

15. FLY AMERICA. [These requirements apply to contracts and subcontracts involving the 9 Rev. 02/2023 FTA Master Agreement dated November 2, 2022 transportation of persons or property by air between a place in the United States and a place outside of the United States, or between places outside the United States, when the FTA will participate in the cost of such air transportation.]

A. As used in this clause: (1) “international air transportation” means transportation by air between a place in the United States and a place outside the United States or between two places both of which are outside the United States; (2) “United States” means the 50 States, the District of Columbia, and outlying areas; and (3) “U.S.-flag air carrier” means an air carrier holding a certificate under 49 U.S.C. Chapter 411.

B. When Federal funds are used to fund travel, Section 5 of the International Air Transportation Fair Competitive Practices Act of 1974 (49 U.S.C. 40118) (Fly America Act) requires contractors, recipients, and others use U.S. -flag air carriers for U.S.

Government-financed international air transportation of personnel (and their personal effects) or property, to the extent that service by those carriers is available. It requires the Comptroller General of the United States, in the absence of satisfactory proof of the necessity for foreign -flag air transportation, to disallow expenditures from funds, appropriated or otherwise established for the account of th e United States, for international air transportation secured aboard a foreign -flag air carrier if a U.S. -flag air carrier is available to provide such services.

C. If available, Contractor, in performing work under this contract, shall use U.S. -flag carriers for international air transportation of personnel (and their personal effects) or property.

D. If Contractor selects a carrier other than a U.S. -flag air carrier for international air transportation, then Contractor shall include a statement on vouchers in volving such transportation essentially as follows:

Statement of Unavailability of U.S. - Flag Air Carriers - International air transportation of persons (and their personal effects) or property by U.S. -flag air carrier was not available or it was necessary to use foreign-flag air carrier service for the following reasons. See FAR § 47.403. [State reasons]:

_____________________________________________
(End of statement)

E. Contractor shall include the substance of this clause, including this paragraph (E), in each subcontract or purchase under this contract that may involve international air transportation.

16. EMPLOYEE PROTECTIONS.

A. Prevailing Wage & Anti -Kickback. [These requirements apply to all prime construction, alteration, or repair contracts in excess of $2,000.]

1. For all prime construction, alteration or repair contracts in excess of $2,000 awarded by FTA, Contractor shall comply with the Davis -Bacon Act and the Copeland “Anti -Kickback” Act. Under 49 U.S.C. § 5333(a), prevailing wage protections apply to laborers a nd mechanics employed on FTA assisted construction, alteration, or repair projects. Contractor will comply with the Davis - Bacon Act, 40 U.S.C. §§ 3141 -3144, and 3146 -3148 as supplemented by DOL regulations at 29 CFR part 5, “Labor Standards Provisions Applicable to Contracts Governing Federally Financed and Assisted Construction.” In accordance with the 10 Rev. 02/2023 FTA Master Agreement dated November 2, 2022 statute, Contractor shall pay wages to laborers and mechanics at a rate not less than the prevailing wages specified in a wage determination made by the Secretary of Labor.

2. In addition, Contractor shall pay wages not less than once a week. Contractor shall also comply with the Copeland “Anti -Kickback” Act (40 U.S.C. § 3145), as supplemented by DOL regulations at 29 CFR part 3, “Contractors and Subcontractors on Public Building or Public Work Financed in Whole or in part by Loans or Grants from the United States.” Contractor is prohibited from inducing, by any means, any person employed in the construction, completion, or repair of public work, to give up any part of the compensation to which he or she is otherwise entitled.

B. Contract Work Hours/Safety Standards for Awards Involving Construction. [These requirements apply to all contracts involving construction in excess of $100,000 that involve the employment of mechanics or laborers.]

1. For all contracts in excess of $100,000 that involve the employment of mechanics or laborers, Contractor shall comply with the Contract Work Hours and Safety Standards Act (40 U.S.C. §§ 3701-3708), as supplemented by the DOL regulations at 29 CFR part 5. Under 40 U.S.C. § 3702 of the Act, Contractor shall compute the wages of every mechanic and laborer, including watchmen and guards, on the basis of a standard work week of 40 hours. Work in excess of the standard work week is permissible provided that the worker is compensated at a rate of not less than one and a half times the basic rate of pay for all hours worked in excess of 40 hours in the work week. The requirements of 40 U.S.C. § 3704 are applicable to construction work and provide that no laborer or mechanic be required to work in surroundings or under working conditions which are unsanitary, hazardous or dangerous. These requirements do not apply to the purchase of supplies or materials or articles ordinarily available on the open market, or to contr acts for transportation or transmission of intelligence.

2. In the event of any violation of the clause set forth herein, Contractor and any subcontractor responsible therefor shall be liable for the unpaid wages. In addition, Contractor and subcontractor sh all be liable to the United States (in the case of work done under contract for the District of Columbia or a territory, to such District or to such territory), for liquidated damages. Such liquidated damages shall be computed with respect to each individual laborer or mechanic, including watchmen and guards, employed in violation of this clause in the sum of $10 for each calendar day on which such individual was required or permitted to work in excess of the standard workweek of forty hours without payment of the overtime wages required by this clause.

3. The FTA shall upon its own action or upon written request of an authorized representative of the Department of Labor withhold or cause to be withheld, from any moneys payable on account of work performed by Contractor or subcontractor under any such contract or any other Federal contract with the same prime Contractor, or any other federally -assisted contract subject to the Contract Work Hours and Safety Standards Act, which is held by the same prime Contractor, such sums as may be determined to be necessary to satisfy any liabilities of such Contractor or subcontractor for unpaid wages and liquidated damages as provided in this section.

4. Contractor or subcontractor shall insert in any subcontracts the clauses set forth in this section and also a clause requiring the subcontractors to include these 11 Rev. 02/2023 FTA Master Agreement dated November 2, 2022 clauses in any lower tier subcontracts. The prime Contractor shall be responsible for compliance by any subcontractor or lower tier subcontractor with the clauses set forth in this Contract.

C. Contract Work Hours/Safety Standards for Awards Not Involving Construction. [These requirements apply to all contracts (not involving construction) in excess of $100,000 that involve the employment of mechanics or laborers.]

1. Contractor shall comply with all federal laws, regulations, and requirements providing wage and hour protections for non -construction employees, in accordance with 40 U.S.C. § 3702, Contract Work Hours and Safety Standards Act, and other relevant parts of that Act, 40 U.S.C. § 3701 et seq., and U.S. DOL regulations, “Labor Standards Provisions Applicable to Contracts Covering Federally Financed and Assisted Construction (also Labor Standards Provisions Applicable to Non-construction Contracts Subject to the Contract Work Hours and Safety Standards Act),” 29 CFR part 5.

2. Contractor shall maintain payrolls and basic payroll records during the course of the work and shall preserve them for a period of three years from the completion of the contract for all labo rers and mechanics, including guards and watchmen, working on the contract. Such records shall contain the name and address of each such employee, social security number, correct classifications, hourly rates of wages paid, daily and weekly number of hours worked, deductions made, and actual wages paid.

3. Such records maintained under this paragraph shall be made available by Contractor for inspection, copying, or transcription by authorized representatives of the FTA and the Department of Labor, and Contrac tor will permit such representatives to interview employees during working hours on the job.

4. Contractor shall require the inclusion of the language of this clause within subcontracts of all tiers.

17. SEISMIC SAFETY. [These requirements apply only to contrac ts for the construction of new buildings or additions to existing buildings.]

Contractor shall design and construct any new building or addition to an existing building in accordance with the standards for Seismic Safety required in Department of Transportation (DOT) Seismic Safety Regulations (49 CFR part 41) and will certify its compliance to the extent required by the regulation. Contractor shall ensure that all work performed under this Contract, including work performed by a subcontractor, is in compliance with the standards required by the Seismic Safety regulations and the certification of compliance issued on the project.

18. VETERANS EMPLOYMENT. [These requirements apply only to capital projects. See 49 U.S.C. § 5302(3).]

Contractor shall give a hiring preference, to the extent practicable, to veterans (as defined in U.S.C. Section 2108 of title 5) who have the requisite skills and abilities to perform the construction work required under the Contract. This requirement shall not be understood, construed or enforced in any manner that would require an employer to give a preference to any veteran over any equally qualified applicant who is a member of any racial or ethnic minority, female, an individual with a disability, or a former employee.

12 Rev. 02/2023 FTA Master Agreement dated November 2, 2022

19. BONDING. [These requirements are applicable to all construction or facility improvement contracts and subcontracts exceeding the simplified acquisition threshold (currently set at $250,000). See FTA Circular C 4220.1F for specific bonding requirements.]

Bonds are required for all construction or facility improvement contracts and subcontracts exceeding the simplified acquisition threshold. FTA may accept the bonding policy and requirements of the AGENCY if FTA has determined that the Federal interest is adequately protected. If such a determination has not been made, the following minimum requirements apply:

A. A bid guarantee from each bidder equivalent to five percent of the bid price. The “bid guarantee” must consist of a firm commitment such as a bid bond, certified check, or other negotiable instrument accompanying a bid as assurance that the bidder will, upon acceptance of the bid, execute such contractual documents as may be required within the time specified.

B. A performance bond on the part of Contractor for 100 percent of the contract price. A “performance bond” is one executed in connection with a contract to secure fulfillment of all of Contractor's obligations under such contract.

C. A payment bond on the part of Contractor for 100 percent of the contr act price. A “payment bond” is one executed in connection with a contract to assure payment as required by law of all persons supplying labor and material in the execution of the work provided for in the contract.

20. PUBLIC TRANSPORTATION EMPLOYEE PROTECTIVE ARRANGEMENTS. [These requirements apply only to contracts for transit operations performed by employees of contractors and subcontractors recognized by FTA to be a transit operator.]

Contractor shall comply with the following employee protective arrangements of 49 U.S.C. § 5333(b):

A. U.S. DOL Certification. Under this Contract or any Amendments thereto that involve public transportation operations that are supported with federal assistance, a certification issued by U.S. DOL is a condition of the Contract.

B. Special Warranty. When the Contract involves public transportation operations and is supported with federal assistance appropriated or made available for 49 U.S.C. § 5311, U.S. DOL will provide a Special Warranty for its Award, including its Award of federal assistance under the Tribal Transit Program. The U.S. DOL Special Warranty is a condition of the Contract.

C. Special Arrangements. The conditions of 49 U.S.C. § 5333(b) do not apply to Contractors providing public transportation operations pursuant to 4 9 U.S.C. § 5310.

FTA reserves the right to make case-by-case determinations of the applicability of 49 U.S.C. § 5333(b) for all transfers of funding authorized under title 23, United States Code (flex funds), and make other exceptions as it deems appropria te, and, in those instances, any special arrangements required by FTA will be incorporated herein as required.

D. Flow Down. Contractor shall include the substance of this clause in each subcontract that may involve operating public transit services.

21. CHARTER SERVICE. [These requirements apply to contracts for operating public transportation service.]

13 Rev. 02/2023 FTA Master Agreement dated November 2, 2022 A. Contractor shall comply w ith 49 U.S.C. 5323(d), (g), and (r), and 49 CFR part 604, which provides that recipients and subrecipients of FTA assistance are prohibited from providing charter service using federally -funded equipment or facilities if there is at least one private chart er operator willing and able to provide the service, except as permitted under: (1) federal transit laws, specifically 49 U.S.C. § 5323(d); (2) FTA regulations, “Charter Service,” 49 CFR part 604; (3) any other federal Charter Service regulations; or (4) Federal guidance, except as FTA determines otherwise in writing.

B. If Contractor engages in a pattern of violations of FTA’s Charter Service regulations, then FTA may require corrective measures or impose remedies on it. These corrective measures and remedie s may include: (1) barring it or any subcontractor operating public transportation under its Award that has provided prohibited charter service from receiving federal assistance from FTA; (2) withholding an amount of federal assistance as provided by Appendix D to part 604 of FTA’s Charter Service regulations; or (3) any other appropriate remedy that may apply.

C. Contractor should also include the substance of this clause in each subcontract th at may involve operating public transit services.

22. SCHOOL BUS OPERATIONS. [These requirements apply to contracts for operating public transportation service.]

Contractor shall comply with 49 U.S.C. 5323(f) and (g), and 49 CFR part 605, and not engage in s chool bus operations using federally -funded equipment or facilities in competition with private operators of school buses, except as permitted under: (A) federal transit laws, specifically 49 U.S.C. § 5323(f); (B) FTA regulations, “School Bus Operations,” 49 CFR part 605; (C) any other Federal School Bus regulations; or (D) federal guidance, except as FTA determines otherwise in writing. If Contractor violates these school bus requirements, then FTA may bar Contractor from receiving Federal assistance for public transportation or require Contractor to take such remedial meas ures as FTA considers appropriate. When operating exclusive school bus service under an allowable exemption, Contractor may not use federally -funded equipment, vehicles, or facilities.

Contractor should include the substance of this clause in each subcontr act or purchase under this Contract that may operate public transportation services.

23. MOTOR CARRIER SAFETY. [These requirements apply to contracts for operating bus operation service.]

A. Financial Responsibility. Contractor shall comply with the economic and insurance registration requirements of: (1) U.S. Federal Motor Carrier Safety Administration (U.S.

FMCSA) regulations, “Minimum Levels of Financial Responsibility for Motor Carriers,” 49 C.F.R. part 387, if Co ntractor is: (a) engaged in operations requiring compliance with 49 C.F.R. part 387, (b) engaged in interstate commerce, and (c) not within a defined commercial zone; and (2) provisions of 49 U.S.C. § 31138(e)(4), which supersede inconsistent provisions of 49 C.F.R. part 387, and reduce the amount of insurance the Recipient must obtain to the highest amount required by any state in which the public transportation provider operates, if it operates within a public transportation service area located in more t han one state, and receives federal assistance under 49 U.S.C. §§ 5307, 5310, and 5311.

B. U.S. FMCSA Requirements. Contractor shall comply with: (1) safety requirements of U.S. Federal Motor Carrier Safety Administration (U.S. FMCSA) regulations, “Federal Motor Carrier Safety Regulations,” 49 C.F.R. parts 390 – 397, to the extent applicable; and (2) driver’s license requirements of U.S. FMCSA regulations, “Commercial 14 Rev. 02/2023 FTA Master Agreement dated November 2, 2022 Driver’s License Standards, Requirements, and Penalties,” 49 C.F.R. part 383, and “State Compliance with Commercial Driver's License,” 49 C.F.R. part 384, to the extent applicable, with the substance abuse requirements and guidance of U.S. FMCSA’s regulations, “Drug and Alcohol Use and Testing Requirements,” 49 C.F.R. part 382, and implementing federal guidance, to the extent applicable.

24. SAFE OPERATIONS OF MOTOR VEHICLES.

A. Seat Belt Use. Contractor is encouraged to adopt and promote on -the-job seat belt use policies a nd programs for its employees and other personnel that operate company-owned vehicles, company- rented vehicles, or personally operated vehicles.

The terms “company-owned” and “company-leased” refer to vehicles owned or leased either by Contractor or AGENCY.

B. Distracted Driving. Contractor shall adopt and enforce workplace safety policies to decrease crashes caused by distracted drivers, including policies to ban text messaging while using an electronic device supplied by an employer, and driving a vehicle t he driver owns or rents, a vehicle Contactor owns, leases, or rents, or a privately-owned vehicle when on official business in connection with the work performed under this Contract.

C. Subcontracts. Contractor shall insert the substance of this clause, including this paragraph, in all subcontracts that exceed the micro -purchase threshold, as defined in Federal Acquisition Regulation 2.101 on the date of subcontract award.

25. CONTRACTOR POLICIES TO BAN TEXT MESSAGING WHILE DRIVING. [These requirements do not apply to micro -purchases ($10,000 or less, except for construction contracts over $2,000).]

A. Definitions. As used in this clause: (1) "driving" means operating a motor vehicle on an active roadway with the motor running, including while temporarily stationary because of traffic, a traffic light, stop sign, or otherwise ( note: "driving" does not include operating a motor vehicle with or without the motor running when one has pulled over to the side of, or off, an active roadway and has halted in a location where one can safely remain stationary); and (2) “text messaging” means reading from or entering data into any handheld or other electronic device, including for the purpose of short message service texting, e-mailing, instant messaging, obtaining navigational information, or engaging in any other form of electronic data retrieval or electronic data communication (note: “text messaging” does not include glancing at or listening to a navigational device that is secured in a commercially designed holder affixed to the vehicle, provided that the destination and route are programmed into the device either before driving or while stopped in a location off the roadway where it is safe and legal to park).

B. Executive Order. This clause implements Executive Order 13513, Federal Leadership on Reducing Text Messaging While Driving, dated October 1, 2009.

Contractor is encouraged to adopt and enforce policies that ban text messaging while driving company-owned/rented vehicles, Government-owned vehicles, and privately- owned vehicles when on official Government business or when performing any work for or on behalf of the Government. Contractor is also encouraged to conduct initiatives in a manner commensurate with the size of the business, such as: (1) establishment of new rules and programs or reevaluation of existing programs to prohibit text messaging while driving; and (2) education, awareness, and other outreach to employees about the safety risks associated with texting while driving. 15 Rev. 02/2023 FTA Master Agreement dated November 2, 2022 C. Subcontracts. Contractor shall insert the substance of this clause, including this paragraph, in all subcontracts that exceed the micro -purchase threshold, as defined in Federal Acquisition Regulation 2.101 on the date of subcontract award.

26. SUBSTANCE ABUSE (DRUG & ALCOHOL TESTING) . [These requirements apply to contracts with contractors who perform safety -sensitive functions, as defined in 49 CFR Part 655.4, “Definitions.”]

A. Contractor shall establish and implement a drug and alcohol testing program that complies with “Procedures for Transportation Workplace Drug and Alcohol Testing Programs” (49 CFR Part 40) and “Prevention of Alcohol Misuse and Prohibited Drug Use in Transit Operations” (49 CFR Part 655), produce any documentation necessary to establish its compliance with parts 655 and 40, and permit any authorized representative of the United States Department of Transportation or its operating administrations, the State Oversight Agency of Arizona, or the City of Phoenix, to inspect the facilities and records associated with the implementation of the drug and alcohol testing program as required under 49 CFR part 655 and 49 CFR part 40 and review the testing process.

B. Contractor shall also submit for review and approval a copy of its substance abuse prevention policy developed to implement its drug and alcohol testing program.

Further, Contractor shall certify annually its compliance with parts 655 and 40 and to submit the Drug and Alcohol Management Information System (DAMIS) reports before March 15 to Transit Compliance Officer, City of Phoenix Public Transit Department, 302 N. 1st Avenue, Phoenix, AZ 85003. To certify compliance, Contractor shall use the "Substance Abuse Certifications" in the "Annual List of Certifications and Assurances for Federal Transit Administration Grants and Cooperative Agreements," which is published annually in the Federal Register.

C. Contractor shall require the inclusion of the language of this clause within subcontracts of all tiers involving the performance of a safety-sensitive function under the Contract.

27. BUY AMERICA. [These requirements apply to contracts over $150,000 if they involve the purchase of iron, steel, manufactured goods, or rolling stock.]

A. Contractor shall comply with 49 U.S.C. 5323(j) and 49 CFR part 661, which provide that federal funds may not be obligated unless all steel, iron, and manufactured products used in FTA -funded projects are produced in the United States, unless a waiver has been granted by FTA or the product is subject to a general waiver. General waivers are listed in 49 CFR § 661.7 and include final assembly in the United States for 15 passenger vans and 15 passenger wagons produced by Chrysler Corporation, microcomputer equipment, and software. Separate requirements for rolling stock are set out at 49 U.S.C. 5323(j)(2)(C) and 49 CFR § 661.11. Contractor must submit to AGENCY the appropriate Buy America certification with its offer. Offers that are not accompanied by a completed Buy America certification will be rejected as nonresponsive.

B. Construction materials used in FTA -funded projects are subject to the domestic preference requirement of the Build America, Buy America Act, Pub. L. 117 -58, div.

G, tit. IX, §§ 70911 – 70927 (2021), as implemented by the U.S. Office of Management and Budget, the U.S. Department of Transportation, and FTA.

28. PROHIBITED TELECOMMUNICATIONS/SURVEILLANCE SERVICES/EQUIPMENT.

The AGENCY is prohibited from obligating or expending loan or grant funds to: procure or obtain, extend or renew a contract to procure or obtain, or enter into a contract (or 16 Rev. 02/2023 FTA Master Agreement dated November 2, 2022 extend or renew a contract) to procure or obtain equipment, services, or systems that uses covered telecommunications equipment or services as a substantial or essential component of any system, or as critical technology as part of any system. Contractor shall not provide covered telecommunications equipment or services in the performance of the Contract. As described in Public Law 115-232, section 889, covered telecommunications equipment is: (A) telecommunications equipment produced by Huawei Technologies Company or ZTE Corporation (or any subsidiary or affiliate of such entities); (B) video surveillance and telecommunications equipment produced by Hytera Communications Corporation, Hangzhou Hikvision Digital Technology Company, or Dahua Technology Company (or any subsidiary or affiliate of such entities) for the purpose of public safety, security of government facilities, physical security surveillance of critical infrastructure, and other national security purposes; (C) Telecommunications or video surveillance services provided by such entities or using such equipment; and (D) telecommunications or video surveillance equipment or services produced or provided by an entity that the Secretary of Defense, in consultation with the Director of the National Intelligence or the Director of the Federal Bureau of Investigation, reasonably believes to be an entity owned or controlled by, or otherwise connected to, the government of a covered foreign country.

29. AIR POLLUTION & FUEL ECONOMY. [These requirements apply to contracts for the purchase of rolling stock.]

The Contractor agrees to comply with applicable Federal air pollution control and fuel economy regulations, such as: EPA regulations, “Control of Air Pollution from Mobile Sources,” 40 CFR Part 85; EPA regulations, “Control of Air Pollution from New and In-Use Motor Vehicles and New and In-Use Motor Vehicle Engines,” 40 CFR Part 86; and EPA regulations, “Fuel Economy of Motor Vehicles,” 40 CFR Part 600.

30. ROLLING STOCK LIMITATIONS. [These requirements apply to contracts for the purchase of rolling stock.]

Contractor and its subcontractors must comply with the limitation on certain rolling stock procurements at 49 U.S.C. § 5323(u), prohibiting the procurement of rolling stock from specified manufacturers for public transportation use.

31. PRE-AWARD & POST -DELIVERY AUDITS OF ROLLING STOCK PURCHASES. [These requirements apply to contracts for the purchase of rolling stock.]

Contractor shall comply with 49 U.S.C. § 5323(m) and FTA's implementing regulation at 49 CFR part 663. Contractor shall comply with the Buy America certification(s) submitted with its offer. Contractor shall participate and cooperate in any pre -award and post -delivery audits performed pursuant to 49 CFR part 663 and related FTA guidance.

32. BUS TESTING. [These requirements apply to contracts for the purchase/lease of any bus model that is new or has any major change in configuration /components to be acquired/leased.]

Contractor [Manufacturer] agrees to comply with the Bus Testing requirements under 49 U.S.C. 5318(e) and FTA' s implementing regulation at 49 CFR part 665 to ensure that the requisite testing is performed for all new bus models or any bus model with a major change in configuration or components, and that the bus model has achieved a passing score. Upon 17 Rev. 02/2023 FTA Master Agreement dated November 2, 2022 completion of the testing, Contractor shall obtain a copy of the bus testing reports from the operator of the testing facility and make that report(s) publicly available prior to final acceptance of the first vehicle by the grantee.

33. ENVIRONMENTAL PROTECTIONS. Contractor shall comply with all applicable environmental and resource use laws, regulations, and requirements, and follow applicable guidance, now in effect or that may become effective in the future, including state and local laws, ordinances, regulations, and requirements and follow applicable guidance.

A. National Environmental Policy Act.

1. Contractor shall comply and facilitate compliance with federal laws, regulations, and requirements, including, but not limited to: (a) federal transit laws, such as 49 U.S.C. § 5323(c)(2), and 23 U.S.C. § 139; (b) the National Environmental Policy Act of 1969 (NEPA), as amended, 42 U.S.C. §§ 4321 et seq., as limited by 42 U.S.C. § 5159, and CEQ’s implementing regulations 40 C.F.R. part 1500 – 1508; (c) joint FHWA and FTA regulations, “Environmental Impact and Relat ed Procedures,” 23 C.F.R. part 771 and 49 C.F.R. part 622; (d) Executive Order No. 11514, as amended, “Protection and Enhancement of Environmental Quality,” March 5, 1970, 42 U.S.C. § 4321 note; and (e) other federal environmental protection laws, regulations, and requirements applicable to Contractor.

2. Contractor shall follow federal guidance to the extent that the guidance is consistent with applicable authorizing legislation, which may include: (a) joint FHWA and FTA final guidance, “Interim Guidance on MAP-21 Section 1319, Accelerated Decision making in Environmental Reviews,” January 14, 2013; (b) joint FHWA and FTA final guidance, “SAFETEA -LU Environmental Review Process (Pub. L. 109-59),” 71 Fed. Reg. 66576, November 15, 2006; and (c) other federal environmental guidance applicable to the Contractor.

B. Environmental Justice. Contractor shall promote environmental justice by following:
(1) Executive Order No. 12898, “Federal Actions to Address Environmental Justice in Minority Populations and Low -Income Populations,” February 11, 1994, 42 U.S.C. § 4321 note, as well as facilitating compliance with that Executive Order; (2) U.S. DOT Order 5610.2, “Department of Transportation Actions To Address Environmental Justice in Minority Populations and Low -Income Populations,” 62 Fed. Reg. 18377, April 15, 1997; and (3) the most recent edition of FTA Circular 4703.1, “Environmental Justice Policy Guidance for Federal Transit Administration Recipients,” August 15, 2012, to the extent consistent with applicable federal laws, regulations, requirements, and guidance.

C. Other Environmental Federal Laws. Contractor shall comply or facilitate compliance with all applicable federal laws, regulations, and requirements, and will follow applicable guidance, including, but not limited to, the Clean Air Act, Clean Water Act, Wild and Scenic Rivers Act of 1968, Coastal Zone Management Act of 1972, the Endangered Species Act of 1973, Magnuson Stevens Fishery Conservation and Management Act, Resource Conservation and Recovery Act, Comp rehensive Environmental Response, Compensation, and Liability Act, Executive Order No. 11990 relating to “Protection of Wetlands,” and Executive Order Nos. 11988 and 13690 relating to “Floodplain Management.”
D. Use of Certain Public Lands. Contractor shall c omply with U.S. DOT laws, specifically 49 U.S.C. § 303 (often referred to as “section 4(f)), and joint FHWA and FTA regulations, “Parks, Recreation Areas, Wildlife and Waterfowl Refuges, and Historic Sites,” 23 C.F.R. part 774, and referenced in 49 C.F.R. part 622. 18 Rev. 02/2023 FTA Master Agreement dated November 2, 2022 E. Historic Preservation. Contractor shall comply with: (1) U.S. DOT laws, including 49 U.S.C. § 303 (often referred to as “section 4(f)”), which requires certain findings be made before an Award may be undertaken if it involves the use of any land from a historic site that is on or eligible for inclusion on the National Register of Historic Places; (2) federal historic and archaeological preservation requirements of section 106 of the National Historic Preservation Act, as amended, 54 U.S.C. § 30610 8; (3) the Archeological and Historic Preservation Act of 1974, as amended, 54 U.S.C. § 312501 et seq.; (4) U.S. Advisory Council on Historic Preservation regulations, “Protection of Historic Properties,” 36 C.F.R. part 800; and (5) other federal requirements and federal guidance to avoid or mitigate adverse effects on historic properties.

F. Indian Sacred Sites. Contractor shall facilitate compliance with federal efforts to promote the preservation of places and objects of religious importance to American Indians, Eskimos, Aleuts, and Native Hawaiians, and facilitate compliance with the American Indian Religious Freedom Act, 42 U.S.C. § 1996, and Executive Order No. 13007, “Indian Sacred Sites,” May 24, 1996, 42 U.S.C. § 3161 note.

34. CLEAN AIR ACT & FEDERAL WAT ER POLLUTION CONTROL ACT. [These requirements do not apply to contracts and subcontracts under $150,000.]

Contractor shall ensure that it: (A) will not use any violating facilities; (B) will report the use of facilities placed on or likely to be placed on the U.S. EPA “List of Violating Facilities;” (C) will report violations of use of prohibited facilities to FTA; and (D) will comply with the inspection and other requirements of the Clean Air Act, as amended (42 U.S.C. §§ 7401 – 7671q); and the Federal Water Pollution Control Act as amended (33 U.S.C. §§ 1251 - 1387).

35. ENERGY CONSERVATION. Contractor shall comply with mandatory standards and policies relating to energy efficiency, which are contained in the state energy conservation plan issued in compliance with the Energy Policy and Conservation Act (42 U.S.C. §§ 6321 et seq.).

36. RECYCLED PRODUCTS (SOLID WASTES). [These requirements apply to all contracts and subcontracts involving the purchase of items designated by the EPA (that contain the highest percentage of recovered materials practicable) in excess of $10,000. See 40 C.F.R part 247 for federal designation of items.]

Contractor shall provide a preference for those products and services that conserve natural resources, protect the environment, and are energy efficient by complying with and facilitating compliance with Section 6002 of the Resource Conservation and Recovery Act, as amended, 42 U.S.C. § 6962, and U.S. En vironmental Protection Agency (U.S. EPA), “Comprehensive Procurement Guideline for Products Containing Recovered Materials,” 40 CFR part 247. The requirements of Section 6002 include: (A) procuring only items designated in guidelines of the U.S. EPA at 40 C.F.R. part 247 that contain the highest percentage of recovered materials practicable, consistent with maintaining a satisfactory level of competition, where the purchase price of the item exceeds $10,000 or the value of the quantity acquired during the preceding fiscal year exceeded $10,000; (B) procuring solid waste management services in a manner that maximizes energy and resource recovery; and (C) establishing an affirmative procurement program for procurement of recovered materials identified in the EPA guidelines.

19 Rev. 02/2023 FTA Master Agreement dated November 2, 2022

37. INTELLECTUAL PROPERTY/PATENT RIGHTS & RIGHTS IN DATA. [These requirements apply to contracts for the performance of experimental, developmental, or research work.]

A. This Project is funded through a Federal award with FTA for experimental, developmental, or research work purposes. As such, certain Patent Rights and Data Rights apply to all subject data first produced in the performance of this Contract.

Contractor shall grant the AGENCY intellectual property access and licenses deemed necessary for the work performed under this Contract and in accordance with the requirements of 37 CFR Part 401, “Rights to Inventions Made by Nonprofit Organizations and Small Business Firms Under Government Grants, Contracts and Cooperative Agreements,” and any implementing regulations issued by FTA or U.S.

DOT. The terms of an intellectual property agreement and software license rights will be finalized prior to execution of this Contract and shall, at a minimum, include the following restrictions: Except for i ts own internal use, Contractor may not publish or reproduce subject data in whole or in part, or in any manner or form, nor may Contractor authorize others to do so, without the written consent of FTA, until such time as FTA may have either released or ap proved the release of such data to the public. This restriction on publication, however, does not apply to any contract with an academic institution. For purposes of this Contract, the term “subject data” means recorded information whether or not copyrighted, and that is delivered or specified to be delivered as required by the Contract. Examples of “subject data” include, but are not limited to computer software, standards, specifications, engineering drawings and associated lists, process sheets, manuals, technical reports, catalog item identifications, and related information, but do not include financial reports, cost analyses, or other similar information used for performance or administration of the Contract.

B. The Federal Government reserves a royalty -free, non -exclusive and irrevocable license to reproduce, publish, or otherwise use, and to authorize others to use for “Federal Government Purposes”: (1) any subject data developed under the Contract, whether or not a copyright has been obtained; and (2) any rights of copyright purchased by Contractor using federal assistance in whole or in part by the FTA. For “Federal Government Purposes,” means use only for the direct purposes of the Federal Government. Without the copyright owner’s consent, the Federal Government may not extend its Federal license to any other party.

C. Unless FTA determines otherwise, Contractor performing experimental, developmental, or research work required as part of this Contract agrees to permit FTA to make available to the public, either FTA’s license in the copyright to any subject data developed in the course of the Contract, or a copy of the subject data first produced under the Contract for which a copyright has not been obtained. If the experimental, developmental, or research work, which is the subject of this Contract, is not completed for any reason whatsoever, all data developed under the Contract shall become subject data a s defined herein and shall be delivered as the Federal Government may direct.

D. Unless prohibited by state law, upon request by the Federal Government, Contractor shall indemnify, save, and hold harmless the Federal Government, its officers, agents, and empl oyees acting within the scope of their official duties against any liability, including costs and expenses, resulting from any willful or intentional violation by Contractor of proprietary rights, copyrights, or right of privacy, arising out of the publication, translation, reproduction, delivery, use, or disposition of any data furnished under that contract. Contractor shall be required to indemnify the Federal Government 20 Rev. 02/2023 FTA Master Agreement dated November 2, 2022 for any such liability arising out of the wrongful act of any employee, official, or agents of the Federal Government.

E. Nothing contained in this clause on rights in data shall imply a license to the Federal Government under any patent or be construed as affecting the scope of any license or other right otherwise granted to the Federal Government under any patent.

F. Data developed by Contractor and financed entirely without using Federal assistance provided by the Federal Government that has been incorporated into work required by the Contract is exempt from the requirements herein, provided t hat Contractor identifies those data in writing at the time of delivery of the Contract work.

G. Contractor shall include these requirements in each subcontract for experimental, developmental, or research work financed in whole or in part with Federal assistance.

38. COMPLIANCE WITH NATIONAL ITS ARCHITECTURE POLICY. [These requirements apply only to contracts for National Intelligent Transportation System projects.]

Contractor shall conform to the National Intelligent Transportation Systems (ITS) Architecture requirements of 23 U.S.C. § 517(d), unless it obtains an exemption from those requirements, and follow FTA Notice, “FTA National ITS Architecture Policy on Transit Projects,” 66 Fed. Reg. 1455, January 8, 2001, and all other applicable federal guidance.

39. NTD REPORTING. As a condition of benefitting from federal assistance for public transportation operations, Contractor and its subcontractors must: (A) facilitate compliance with 49 U.S.C. § 5335(a), which authorizes the National Transit Database (NTD); (B) conform to the NTD reporting system and the Uniform System of Accounts and Records; (C) comply with FTA regulations, “Uniform System of Accounts and Records and Reporting System,” 49 CFR Part 630; (D) report when required to the National Transit Database in accordance with FTA regulation 49 CFR Part 630, “National Transit Database,” and applicable FTA instructions: (1) any information relating to a transit asset inventory or condition assessment; (2) any data on assaults on transit workers; (3) any data on fatalities that result from an impact with a bus; and (4) such other information as FTA may require; (E) comply with any other applicable reporting regulations, and requirements; and (F) follow FTA guidance.

40. TRAFFICKING IN PERSONS. Contractor and its subcontractors or their employees shall not: (A) engage in severe forms of trafficking in persons during the Contract Term; (B) procure a commercial sex act during the Contract Term; or (C) use forced lab or in the performance of the Contract. Contractor shall inform AGENCY immediately of any information Contractor receives from any source alleging a violation of a prohibition in this section. AGENCY may terminate this Contract for any violation of this section; such right of termination is in addition to all other remedies for noncompliance that are available to the AGENCY.

41. DBE REQUIREMENTS.
(DBE requirements to be provided by PTD Compliance Section)

21 Rev. 02/2023 FTA Master Agreement dated November 2, 2022

FTA CERTIFICATIONS

EACH CERTIFICATION PROVIDES

INSTRUCTION DESCRIBING WHEN

THE CERTIFICATION IS APPLICABLE

INAPPLICABLE FTA CERTIFICATIONS

MAY BE LEFT BLANK

OFFERS THAT DO NOT INCLUDE

COMPLETED CERTIFICATIONS,

IF APPLICABLE,
WILL BE REJECTED AS NONRESPONSIVE.

22 Rev.
02 /202
3 FTA Master Agreement dated
November 2
, 202
2 DEBARMENT AND SUSPENSION CERTIFICATION

This certification does not apply to contracts and subcontracts under $25,000. Offers that do

not
include this

completed certification
, if applicable,

will be rejected as nonresponsive.

Check one

box below (and provide explanation if necessary)
:

□

The Proposer certifies that the Proposer and its principals:

1. Are not presently debarred, suspended, proposed for debarment, declared ineligible, or
voluntarily or involuntarily excluded from covered transactions by any federal department or agency;

2. Have not, within the preceding three years, been convicted of or had a civil judgment rendered against them for commission of fraud or a cr
iminal offense in connection with
obtaining, attempting to obtain, or performing a public or private agreement or transaction; violation of federal or state antitrust statutes, including those proscribing price fixing between competitors, allocation of cus
tomers between competitors, and bid
rigging; commission of embezzlement, theft, forgery, bribery, falsification or destruction of records, making false statements, tax evasion, receiving stolen property, making false claims, or obstruction of justice; or c
ommission of any other offense indicating a lack of
business integrity or business honesty;

3. Are not presently indicted for or otherwise criminally or civilly charged by a governmental entity (federal, state, or local) with commission of any offense descr ibed in Paragraph 2
of this certification;

4. Have not, within the preceding three years, had one or more public transactions (federal, state, or local) terminated for cause or default.

-

OR
–

□

The Proposer is unable to certify to all of the statements in this certification, and attaches its
explanation to this certification. (In the explanation, the Proposer must certify to those statements that can be certified and explain why the other statements cannot be certified.)

The Proposer shall require that the language of this certification be included in the contract

documents for all
subcontractors and material suppliers

at all tiers, and that all subcontractors
and material suppliers

shall certify and disclose accordingly.

The Proposer certifies or affirms the truthfulness and accuracy of the contents of the statements submitted on or with this certification. In addition, the Proposer understands and agrees that the provisions of 31 U
.

S
.

C
.

§§ 3801 et al. are applicable to t
his certification.

Company:

_________________________________________________________________

Name:
____________________________________________________________________

Title:

_____________________________________________________________________

Signature:

_________________________________________________________________

Date:

_____________________________________________________________________

THE AFTERMARKET PART COMPANY, LLC dba NFI PARTS

12.30.24 John Proven
President, NFI Parts
23 Rev.
02 /202
3 FTA Master Agreement dated
November 2
, 202
2 BUY AMERICA CERTIFICATION

Th
is certification applies to contracts over $150,000 if they involve the purchase of iron, steel, manufactured goods, or rolling stock.

Offers that
do not include this

completed certification
, if
applicable,

will be rejected as nonresponsive.

If this Offer is valued in excess of $150,000 and
involves the procurement of steel, iron, or
manufactured products (as defined in 49 CFR §§ 661.3 and 661.5),

the Proposer hereby
certifies that it:

□

Will comply
with the requirements of 49 U
.

S
.

C
.

§ 5323(j)(1) and the applicable
regulations in 49 CFR part 661
;

OR

□

Cannot comply the requirements of 49 U
.

S
.

C
.

§ 5323(j) (and 49 CFR part 661) but may
qualify for an exception to the requirements pursuant to 49 U .

S
.

C
.

§ 5323(j)(2), as
amended, and the applicable regulations in 49 CFR § 661.7.

If this Offer is valued in excess of $150,000 and
involves

the procurement of buses or other
rolling stock (including associated equipment),

the Proposer hereby certifies that
it:

□

Will comply with the requirements of 49 U
.

S
.

C
.

§ 5323(j) and the applicable regulations
of 49 CFR § 661.11
;

OR

□

Cannot comply with the requirements of 49 § U
.

S
.

C
.

5323(j) (and 49 CFR § 661.11), but
may qualify for an exception to the requirements co
nsistent with 49 U
.

S
.

C
.

§
5323(j)(2)(C), as amended, and the applicable regulations in 49 CFR § 661.7.

The Proposer certifies or affirms the truthfulness and accuracy of the contents of the statements submitted on or with this
certification. In addition, the Proposer understands and agrees that the provisions of 31 U
.

S
.

C
.

§§

3801 et al. are applicable to this certification

Company:

_________________________________________________________________

Name:
____________________________________________________________________

Title:

_____________________________________________________________________

Signature:

_________________________________________________________________

Date
:

_____________________________________________________________________

THE AFTERMARKET PART COMPANY, LLC dba NFI PARTS

12.30.24 John Proven
President, NFI Parts
24 Rev.
02 /202
3 FTA Master Agreement dated
November 2
, 202
2 LOBBYING CERTIFICATION

Th
is

certification

do
es

not apply to contracts and subcontracts under $100,000.

Offers that
do

not
include this

completed certification
, if applicable,

will be r
ejected as nonresponsive.

The Proposer certifies that:

1. No federal appropriated funds have been paid or will be paid, by or on behalf of the Proposer, to any person for influencing or attempting to influence an officer or employee of an agency, a Member of Congress, an officer or employee of Congress, or an emp
loyee of a Member of Congress in connection with the awarding of any federal contract, the making of any federal grant, the making of any federal loan, the entering into of any cooperative agreement, and the extension, continuation, renewal, amendment, or
modification of any federal contract, grant, loan, or cooperative agreement.

2. If any funds other than federal appropriated funds have been paid or will be paid to any person for influencing or attempting to influence an officer or employee of any agen cy, a
Member of Congress, an officer or employee of Congress, or an employee of a Member of Congress in connection with this federal contract, grant, loan, or cooperative agreement, the Proposer shall complete and submit Standard Form -
LLL, “Disclosure
Form

to Report Lobbying,” in accordance with its instructions.

3. The Proposer shall require that the language of this certification be included in the contract

documents for all
subcontractors and material suppliers

at all tiers, and that all
subcontractor
s
and material suppliers

shall certify and disclose accordingly.

This certification is a material representation of fact upon which reliance was placed when this transaction was made or entered into. Submission of this certification is a prerequisite for

making or entering into this transaction imposed by section 1352, title 31, U.S. Code. Any person who fails to file the required certification shall be subject to a civil penalty of not less than $10,000 and not more than $100,000 for each such failure.

The Proposer certifies or affirms the truthfulness and accuracy of the contents of the statements submitted on or with this certification. In addition, the Proposer understands and agrees that the provisions of 31 U
.

S
.

C
.

§§

3801 et al. are applicable to th
is certification.

Company:

_________________________________________________________________

Name:
____________________________________________________________________

Title:

_____________________________________________________________________

Signature:

_________________________________________________________________

Date
:

_____________________________________________________________________

Per paragraph 2 above, compl
ete and submit Standard Form
–
LLL, “Disclosure Form to Report
Lobbying,” if applicable.

THE AFTERMARKET PART COMPANY, LLC dba NFI PARTS

12.30.24 John Proven
President, NFI Parts
25 Rev.
02 /202
3 FTA Master Agreement dated
November 2
, 202
2 CERTIFICATE OF COMPLIANCE WITH BUS TESTING REQUIREMENT

Th
is certification

appl
ies

to contracts for the purchase or lease of any bus model

that is new

or
has
any major change in configuration or components to be acquired or leased.

Offers that
do

not
include this

completed certification
, if applicable,

will be rejected as nonresponsive.

The Proposer certifies that the bus was tested at the Bus Testing Facility and that the bus received a passing test score as required by 49 CFR Part 665. The applicant has received or will receive the appropriate full Bus Testing Report and any applicabl e partial testing reports
before final acceptance of the first vehicle.

The Proposer understands that misrepresenting the testing status of a vehicle acquired with federal financial assistance may subject the undersigned to civil penalties as outlined in the
Department of Transportation’s regulation on Program Fraud Civil Remedies, 49 CFR Part 31.

In addition, the Proposer understands that FTA may suspend or debar a manufacturer under the procedures in 49

CFR Part 29.

The Proposer certifies or affirms the

truthfulness and accuracy of the contents of the statements submitted on or with this certification. In addition, the Proposer understands and agrees that the provisions of 31 U
.

S
.

C
.

§§

3801 et al. are applicable to this certification.

Company:

________
_________________________________________________________

Name:
____________________________________________________________________

Title:

_____________________________________________________________________

Signature:

_________________________________________________________________

Date
:

_____________________________________________________________________

THE AFTERMARKET PART COMPANY, LLC dba NFI PARTS

12.30.24 John Proven
President, NFI Parts
26 Rev.
02 /202
3 FTA Master Agreement dated
November 2
, 202
2 TRANSIT VEHICLE MANUFACTUR
ER

DISADVANTAGED BUSINESS ENTERPRISE

CERTIFICATION

This certificate applies to contracts for the purchase of rolling stock.

Offers that
do not include
this

completed certification
, if applicable,

will be rejected as nonresponsive.

The Proposer, a Transit Vehicle Manufacturer, hereby certifies that it has complied with the requirements of 49 CFR
§

26.49 by submitting an annual DBE goal to the Federal Transit Administration (FTA). The goal has eith
er been
approved

or
is pending approval

by FTA.

The Proposer certifies or affirms the truthfulness and accuracy of the contents of the statements submitted on or with this certification. In addition, the Proposer understands and agrees that the provisions

of 31 U
.

S
.

C
.

§§

3801 et al. are applicable to this certification.

Company:

_________________________________________________________________

Name:
____________________________________________________________________

Title:

_____________________________________________________________________

Signature:

_________________________________________________________________

Date
:

______________________
_______________________________________________

THE AFTERMARKET PART COMPANY, LLC dba NFI PARTS

12.30.24 John Proven
President, NFI Parts
27 Rev.
02 /202
3 FTA Master Agreement dated
November 2
, 202
2 FEDERAL MOTOR VEHICLE SAFETY STANDARDS CERTIFICATION

This certificate applies to contracts for the purchase of rolling stock.

Offers that
do not include
this
completed certification
, if
applicable,

will be rejected as nonresponsive.

The Proposer certifies that it shall submit, if awarded the Contract: (1) the manufacturer’s FMVSS self
-
certification sticker information that the vehicle complies with relevant FMVSS; or (2) the manufacture
r’s certified statement that the contracted buses will not be subject to FMVSS regulations.

The Proposer certifies or affirms the truthfulness and accuracy of the contents of the statements submitted on or with this certification. In addition, the Propose r understands and agrees that the
provisions of 31 U
.

S
.

C
.

§§

3801 et al. are applicable to this certification.

Company:

_________________________________________________________________

Name:
____________________________________________________________________

Title:

_____________________________________________________________________

Signature:

_________________________________________________________________

Date
:

______________________
_______________________________________________

THE AFTERMARKET PART COMPANY, LLC dba NFI PARTS

12.30.24 John Proven
President, NFI Parts
28 Rev.
02 /202
3 FTA Master Agreement dated
November 2
, 202
2 TAX LIABILITY CERTIFICATION

This certificate applies to all contracts.

Offers that
do not include this

completed certification

will
be rejected as nonresponsive.

The Proposer certifies that:

1. I
t has no
unpaid federal tax liability that has been assessed, for which all judicial and administrative remedies have been exhausted or have lapsed, and that is not being paid in a timely manner pursuant to an agreement with the authority responsible for collecting

the tax liability;

2. I
t has not been convicted of a felony criminal violation under any federal law within the preceding 24 months; and

3. I
t shall require that the language of this certification be included in the award documents for all subcontractors and material suppliers at all tiers, and that all subcontractors and material suppliers shall certify and disclose accordingly.

The Proposer
certifies or affirms the truthfulness and accuracy of the contents of the statements submitted on or with this certification. In addition, the Proposer understands and agrees that the provisions of 31 U
.

S
.

C
.

§§

3801 et al. are applicable to this certificat
ion.

Company:

_________________________________________________________________

Name:
____________________________________________________________________

Title:

_____________________________________________________________________

Signature:

_________________________________________________________________

Date
:

_____________________________________________________________________

THE AFTERMARKET PART COMPANY, LLC dba NFI PARTS

12.30.24 John Proven
President, NFI Parts
29 TORRANACE
FEB 2023 Thur Mar 2024
Pricing subject to change

PN DESCRIPTION LEAD TIME PRICE
000502 LATCH-RUBBER 77 $10.22
001567 TAPE-FOIL 20 $0.26
006098 GAS SPRING 50LB 70 $24.80
008443 SPOUT TUBE DRAIN 86 $25.04
009594 SPRING AIR REAR 25 $96.00
010263 BRAKE TREADLE & PLT ASSY 20 $217.09
013480 CLAMP-LOWER RAD TUBE 120 $11.42
015697 SWITCH 126 $6.99
015988 ASSY-RADIUS ROD LO/REAR 95 $415.98
015988NFA RADIUS ROD LOWER REAR 100 $243.47
024598 BELT 2/5V 85 LG 40 $67.59
028889 ELBOW SILICONE 90 2.25 65 $81.64
034528 HOSE-HUMP 2.50 ID 45 $17.53
034530 HOSE-SILICONE 4.00 ID 27 $15.80
038114 NUT-CAPPED LF ALUM DUAL 30 $15.91
038115 NUT-CAPPED LF ALUM SNGL 30 $14.08
038158 ELBOW SILICONE 2.5 1DX90D 45 $60.77
039682 BOLT M8 x 1.25 MM x 25 MM 45 $3.91
039885 KIT-BOLT & STRAP 1810 20 $10.81
049522 ELBOW-90 DEG 1/2TX1/4 FPTSS 10 $43.66
050904 SPACER ROD END 20 $1.99
052165 PAD-SHORT RUBBER 45 $26.29
052949 ASSY-MARK LAMP AMB LED 57 $13.96
055089 BELLOWS AIR W/O STOP 25 $105.93
055699 ADHESIVE SIKA 252 WHITE 35 $9.78
055701 (OBS) SIKA 221 WHITE - FIELD USE ONLY 25 $5.40
058614 INSERT STEEL 5/16" - 18 UNC X .150"-.312" 30 $0.33 058667 PANEL-LWR RH CTR 25 $608.33
060580 SWITCH ASSY REMOTE MIRROR 45 $93.54
064449 WHL-STEERING 18" 2 SPOKE PADDED 40 $95.34
065958 DECAL-EMER FUEL SHT OFF 25 $7.61
066010 ADAPTER-3/8TB - 1/4NPT 10 $20.23
066157 KIT STAND OFF BOLT 17 $34.94
068793 MOUNT-RUBBER 22001 SER. 87 $7.08
070515NFA SOCKET-BALL STUD RH THREAD 110 $28.84
07-10-1415 SIGN ASM-FRONT,HANOVER,17X160, PFLD,AMBER 35 $1,791.96 084687 RECPT-SST SHEREX 5000 25 $546.68
086238 WIPER-ARM ASSY 34.0 WET 95 $191.92
087654KIN FILTER-POLYESTER REAR AC 75 $9.25
089170 LAMP-SIDE TURN LED 18 115 $23.46
089641 FTG-.5" BLKHD FEED THRU 45 $40.93
30 ATTACHMENT 3
092586 CLAMP-P 0.750 30 $0.62
092590 CLAMP-P 1.250 20 $0.95
097016 SCREW-TPG M8 X 25MM 25 $5.72
097485 CLAMP-T-BOLT W/SPRING 30 $8.11
097488 ROLLER-TENSIONING 25 $49.54
1013116 ASSY-MARK LAMP AMB LED 60 $20.61
102264 CYLINDER ASSEMBLY 25 LBS. 80 $31.39
102773 ELBOW-90 DEG SIL .075 ID 55 $27.06
106428 ELBOW-CAC-90 DEG-4 I.D. 57 $178.75
109753 CONNECTOR-9/16ORBX1/2TU 15 $39.14
109863 WASHER-ENGINE REBOUND 87 $19.50
109982 MOUNT-ENG CIRCULAR-45 110 $63.17
10B10088 BOLT-HEX 5/8 UNC X 5.50 35 $2.27
10B12064 BOLT HEX 3/4" 10 UNC X 4" LG 20 $2.02
10B12104 BOLT-HEX 3/4 UNC X 6.50 25 $4.84
111746 (OBS) GAUGE-2IN.PRESS. 0-200 30 $92.58
112218 HANDLE ASSY DOOR CNTR 65 $61.23
115906 ASSY-GROUND WIRE 20 $15.50
116019 MOUNT-ENGINE METACONE60 102 $86.97
116434 SHOCK ABSORBER-KONI LF RR 20 $115.41
117138 BOLT FLEXPLATE C8.3 25 $6.41
117139 BOLT-CRANKSHAFT C8.3 27 $12.45
11S00006 SCREW FH CROSS RECESS SS #10 32 UNF X 3/8" LG. 25 $0.14 122824 ASSY-PROXIMITY SWITCH 35 $201.69
127000 ISOLATOR-EXHAUST 20 $43.79
129033 PANEL-FRANG ENG/SPN 65 $36.62
130733 NUT-LOCK UNITORQUE 3/4 90 $1.23
130985 GAS SPRING-GS 5300 70 $30.16
133695 ELECTRIC-ACTUATOR MOD 17 $245.07
133704 SENSOR GAS W/CLAMP 10 $145.44
138559 ALARM-BACK UP 90 $57.49
145366 CYL-AGENT W/PRSW VH25 47 $1,076.76
149575 CONN-4CCT SHR DT 115 $10.68
149576 CONN-RCPT 6CCT DEUTSCH 115 $17.99
149650 THERMOSTAT-MINI MOD350F 20 $171.70
165544 LOOM-THERM-L WRAP 36" 20 $22.94
172950 BREAKER-6A MEDIUM DELAY 20 $13.83
20-00-0067 WRENCH-ADB22X,CALIPER,27MM 42 $511.43
204845 NUT-SLEEVE 10-32 UNF 35 $4.30
205042 CLAMP-EXH V/BAND 4.75 60 $36.30
20W12000 WASHER FLAT HARDENED 3/4" 20 $0.52
211043 GUARD-PUSHBUTTON MOM 45 $52.60
214266 GAUGE-FUEL 90 $63.61
214862 SENDER-AIR PRESSURE 90 $103.51
215004 CABLE-NGI NETWORK 12 90 $12.99
215540 ASSY-FRT TURN AMB 4 LED 60 $54.10
219013 WHEEL-ALUM DURA-BRIGHT 40 $581.03
31 223196 SPACER-RADIUS ROD MTG 20 $3.15
227822 NOSING-EXIT YL ALTRO MD 30 $141.20
228742 VALVE-LEVELING 8.00 ARM 80 $62.99
236652 CAP-RADIATOR 16 PSIG 43 $3.87
240064 BOLT-M14 X 1.5 X 65 CL10.9 20 $1.90
246775 ASSY-LAMP BACKUP LED 4" 35 $65.30
247103 ASSY-EXT MIRROR,LH 28 $617.42
253748 CHMBR-BK FRT MGM E-STRK 20 $210.54
266142 ASSY-LAMP LED 45 X 10 35 $53.16
273040 GAUGE-CNG HIGH PRESSURE 50 $115.91
278854 GLASS-DEST LAM 56 $282.91
280555 PUMP-AMETEK 6:00 BLAST 103 $1,395.40
282102 ASSY-RH REM MIRROR SW 20 $86.94
282103 ASSY-LH REM MIRROR SW 20 $141.37
282469 RESISTOR-PACK 910 OHM 45 $18.13
284133 PANEL-DISPLAY F&G AVSN 20 $981.83
284169 VALVE-DUMP, ENTR DOOR 45 $114.66
289316 KIT-LINK LEVELING RR 80 $17.74
290882 ROD-RAD UPR RR LF MAN 70 $264.77
292673 ASSY-AMBER/TURN LED DIA 60 $58.63
295635 CLAMP-TWIN .7 DIA 30 $89.63
296483 BOLT-CARRIAGE 316 SST 1/4-20 X 2 20 $0.51
299616 HEADLAMP-LOW BEAM 65 $53.16
299617 HEADLAMP-HIGH BEAM 65 $48.49
303734 BELLOWS-AIR SPRING 1T15L-4 25 $100.86
3049221 SEAL-D RING 62 $3.22
320860 (OBS) SW-ROTARY 5POS 60 $107.75
322542 ELBOW-90D SILICONE 1.00ID 25 $27.64
324446 HOSE-CNG FUEL ISL G -8 60 $274.41
326465 WINDSHIELD-CURB SIDE NO TINT 56 $443.06
327890 HOUSING-BACK BEARING 30 $34.34
329565 TUBE-TRANS FILL 30 $129.12
331992 CLAMP-EXHAUST TURBO 4.0 V-BAND 70 $60.50
332501 COOLER-TRANS ROCORE 80 $2,032.93
332957 GLASS-ENTR AFT FULL GEN4 70 $65.23
332958 GLASS-ENTR FWD FULL GEN4 90 $65.23
334929 PROBALIZER-KST VALVE 20 $24.00
336047 DAMPER-SHORT STEERING W/SLEEVE 140 $417.31
336997 PANEL-SURGE TANK DOOR 20 $72.76
337588 STRIKER-LATCH, SDS ENCL 30 $124.26
345372 PIN-SPRING 3/8 X 1 1/2 LG 20 $1.67
348488 BLOWER-DRIVER BRLS 24V 133 $1,429.69
351229 GLASS-ENTR FWD TOP AMERI 28 $60.60
351232 GLASS-ENTR 72 GRN BOTT AMERI L 49 $96.97
351500 SPACER-DUAL SWIVEL SADDLE 28 $1.75
351515 KNOB 147 $13.01
352644 ASSY-FB DOOR W/ LATCH 20 $421.82
32 352991 BRACKET-ROLLER A/C BELT 30 $26.51
353028 SPACER-TUBE 1.0 OD STL 71 $9.82
354445 ASSY-RAMP PIVOT LH 35 $86.86
354449 ASSY-RAMP PIVOT RH 35 $86.95
354724 WASHER-M14 HARDENED THIN 37 $0.58
355487 BOLT-HEX LK FLG BLK 5/16 30 $0.47
356808 BOLT-M18 X 1.5 X 100 CL10.9 57 $3.86
360078 FENDER-POLYURETHANE 20 $121.26
369382 GASKET-MARMON 4" STD 37 $16.90
370035 STRUT-GAS SPR 10 LBS 7.8 EXT LG 70 $27.79
377370 TUBE-EXHAUST FLEX AND ELBOW 37 $443.51
379615 LATCH-ROTARY RH 50 $54.21
380515 GASKET-SURGE TANK 20 $2.00
382777 BELT-2/5V X 85.00LG EPDM 60 $64.50
384352 REGULATOR-ITT CNG 45 $602.22
386203 ASSY-HOSE 2807-16 FL17 112 $81.25
386671-TFM2729 TMPLT-ALTRO EXIT DOOR 65 $105.25
388164 WASHER-HARDENED 5/8, FLAT 30 $3.86
392167 LOUVER-4.00 IN DIA 164 $34.93
392759 LOUVER-3.00 IN DIA 80 $53.79
393842 ASSY-DRAG LINK DISC 4" JOUNCE 30 $538.59
393842NFA DRAG LINK-ASSY 100 $316.93
395102 ASSY-HOSE 2807-16 FL34 112 $104.10
395859 GASKET-MARMON 3.5" STD 35 $27.83
404482 PIVOT-LOWER EXIT AFT XCELSIOR 65 $156.23
405191 ASSY-LINK LEVELING 20 $45.51
405265 ASSY-LINK,LVLNG RRLH 20 $34.00
411267 HOSE-ASSY EQ1-04 FL32.0 10 $16.67
413254 (OBS) GAUGE-TEMPERATURE 40 $127.66
413313 HOSE-ASSY NOZ2-04 FL35.0 10 $18.03
414830 ASSY-HOSE EQ1T-REX-20 FL24 11 $147.03
414831 ASSY-HOSE EQ1T-REX-20 FL26.5 18 $150.18
415687 PIVOT-ENT FWD LOWER 65 $112.89
417367 CHAIN-ROLLER #41 X 35.5 LG AC 30 $19.67
417370 LINK-CONNECTING #41 AC 37 $2.04
417372 LINK-OFFSET #41 AC 37 $4.06
420598 HOSE-ASSY EQ1HT -12 FL24.5 20 $52.43
421361 ASSY-HOSE NOZ2-04 FL30.0 15 $19.49
424518 BLANKET-EXHAUST TUBE ISL CNG 40 $797.08
425432 (OBS) BELLOW-EXH HUTCHINSON 170 $1,087.66
425568 ASSY-HOSE EQ1T-REX-20 FL31 20 $104.28
425569 ASSY-HOSE EQ1T-REX-20 FL50 20 $113.88
426010 ASSY-LED STRIP LIGHT 90 $117.38
426110 ASSY-HOSE NOZ2-06 FL 29.0 12 $23.44
427554 ASSY-HOSE EQ1T-REX-20 FL19.0 20 $156.40
438921 ASSY-ELECT CHIME (NO BOX) 120 $73.67
439139 ASSY-LAMP RED STT 7 LED CNG 35 $74.56
33 440744 ASSY-STOP/TAIL LED DIAL CNG 57 $43.81
441224 TRIM-JOINER STRIP U/D 64 $9.23
442004 STRIP-JOINER AD PANELS LF 64 $8.39
445282 ASSY-EXT MIRROR, RH 28 $668.21
448548 WINDSHIELD-CURBSIDE, NO SHADE 56 $426.66
449299 (OBS) ASSY-ENGINE DR CLG FAN 65 $220.38
449400 SWITCH-PUSHBUTTON 80 $37.96
450310 ASSY-LICENCE PLT RETAINER BUMPER 20 $118.87
451982 CONN-3/8TBX7/16ORB 15 $31.24
452822 ASSY-POTENTIOMETER 20 $118.37
454108 ASSY-HOSE NOZ2-04 FL14.5 10 $16.15
455736 ASSY-SILENT ALARM SW 50 $135.65
457022 BLANKET-EXHAUST TUBE ISL2010 G 50 $1,180.74
458592 DUCT-INSUL AIR 3.0" DIA 20 $227.51
460194 ASSY-DOUBLE HINGE HIDDEN 150 $32.06
460604 KIT-HANDLE 1.0 UPA3 90 $11.57
460605 SCREW-HEX SOC 5/16X2.00 90 $2.32
460721 ASSY-SENSOR LOW FLUID 122 $152.07
460722 SENSOR-LOW FLUID LEVEL 105 $48.09
466913 ASSY-BUSBAR RESIS 4CCT 90 $34.54
468339 OCU-TWIN VISION DR 25 $1,481.74
478879 ASSY-LAMP STRIP LED RED 18 INCH 35 $63.00
480283 VALVE-SR7 SPRING BRAKE 20 $266.65
482569 HRNS-LH RR CLR LPS XN 30 $445.97
485591 WINDSHIELD-STREET, NO SHADE 40 $432.01
485937 KIT-POTENTIOMETER TEMP 127 $90.72
487858 ASSY-EXT MIRROR,SS 28 $496.83
487885 ASSY-EXT MIRROR,CS 28 $532.31
488399 ASSY-HOSE NOZ2-04 FL25.0 10 $19.30
492756 MOUNT-METACONE 60 HIGH TEMP 137 $106.23
492796 STRUT-GAS 130 LBF .75 STUD 70 $40.07
492838 STRUT-GAS 130 LBF LOCK .75 STUD 70 $51.35
494935 MODULE-VMM 1615 80 $417.70
495287 BELLOW-EXHAUST DURAFLEX BRAIDED 85 $359.13
498794 CAP-SURGE TANK, COOLANT 70 $68.61
499546 MOUNT-ENG CIRC 45 HIGH TEMP 103 $76.91
504048 SW-ROTARY 5POS 60 $115.00
507730 SELECTOR-SHIFT P/BUTTON 15 $1,032.20
507992 MODULE-DISPLAY IP 40' MPH 70 $709.33
510536 BUZZER-PIEZO 3-6 PULSE RATE 20 $27.40
518608 ASSY-HOSE 2807-4 FL19.0 112 $41.77
521196 STRUT-GAS 80 LBF .75 STUD 70 $42.77
521907 STRUT-GAS 80 LBF LOCK .75 STUD 70 $42.44
523585 KIT-FAN REVERSE/DIAGNOSTIC 67 $199.55
526515 ADHESIVE-PLEXUS MA1020 25 $103.20
534426 STANDOFF-SLIDE IN, XCELSIOR LA 23 $182.94
536387 PANEL-FRANG ENG/SPN 70 $25.09
34 554006 HOSE-HUMP 62MM ID 87 $32.94
554114 CLAMP-IDEAL SMARTSEAL .625-2.64 20 $3.81
554252 BRACKET-MTG CS EXT MIRROR 20 $329.48
555540 ELBOW-45D SILICONE 49MM ID 87 $32.96
557063 BUTTON-HORN W/LOGO 40 $14.77
565103 BLOCK-SWAY BAR GIRDLE 70 $96.07
570882 ELBOW-90 DEG 62MM ID 87 $47.07
571154 ELB-SILICONE 90 27MM ID 87 $49.40
571540 ELBOW-SILICONE 21MM ID, 4 PLY 87 $28.30
572074 PANEL-CNG SIDE SCREEN CS RR 27 $703.02
572978 ASSY-FUSE BOX DOOR 30 $1,972.14
574169 ROD-RADIUS UPPER FRONT 110 $372.92
574955 SPACER-SWAY BAR 25 $3.19
575269 BUSHING-STABILIZER BAR 60 $33.57
579382 BLANKET-EXHAUST TUBE ISL G 40 $877.86
579804 NUT-CASTLE M12 X 1.5 25 $2.52
579878 ELBOW-SILICONE CAC 4.0 I.D. 25 $183.85
590097 ASSY-CORNER PILLAR RH 70 $748.40
590888 BUTTON-STOP REQUEST 90 $15.19
5922666 NOZZLE 100 $3.32
5925959 SWITCH-FOOT, TURN SIGNAL/PA MOD 90 $16.16
5946369 HANDLE-T REMOVEABLE 20 $8.05
5951270 SWITCH MASTER 7PRG 20 $28.05
5955564 KNOB MASTER SWITCH 30 $7.03
5955980 ADAPTER-REDUCING 1/8NPT 19 $0.68
5956149 CONNECTOR HS ND 3/8IDX3/8PT 60 $4.21
5957380 TEE 100 $1.52
5959599 CONNECTOR 92 $1.02
5962576 SWITCH MAGN STARTER 30 $18.03
5963353 PERMASTICK .5 WD 20 $0.08
596361 RACK-BIKE TRILOGY SST 30 $2,222.93
5995795 STRAP-GROUND 25" LONG 55 $8.78
606462 PUMP-AMETEK,BARBED,3:00 BLAST 120 $1,431.13
607495 TEE-1/4NPT X 4JIC X 6JIC ORF 35 $299.71
608025 ASSY-HOSE NOZ2-04 FL51.0 15 $25.94
608026 ASSY-HOSE NOZ2-04 FL16.5 15 $17.14
60R02007 RIVET AL 1/8 GRP 12-.31 20 $0.15
615124 ASSY-HOSE NOZ2-06 FL29.0 15 $20.46
617691 ASSY-HOSE NOZONE-12 FL34.0 15 $50.86
618029 VALVE-DUMP ENTR DOOR COMP 65 $155.88
625-2627-001 SIGN,EXT,REAR,HYBRID,AMBER 45 $3,793.19
6303163 SPRING 52 $5.37
6303804 SPRING SASH LATCH 25 $1.09
6308683 KIT CLUTCH MTG 215 $920.56
6308684 SCREW, CLUTCH MTG 17 $25.51
6310782NFA REFILL , WIPER BLADE 26 " 80 $3.27
6312248 BEARING TAPERED ROLLER 100 $116.18
35 6312249 BEARING ROLLER TAPERED 50 $70.18
6312287 WASHER 95 $14.55
6312288 WASHER 80 $19.33
6312406 VALVE-KIT PURGE 20 $223.25
6313274 EXTRACTOR TOOL, BASIC 80 $459.24
6319594 WASHER 25 $5.73
6321887 KIT TILT STOP 40 $57.30
6326698 BOLT, M10 X 1.5 X 35 20 $12.09
6326714 O-RING. INT 15 $6.21
6331005 VALVE-SHUT OFF 21 $46.59
6331009 WATER FILTER-WF2074 CUMMINS 27 $22.26
6331970 FILTER, NG FUEL - SPIN ON 32 $41.22
6333472 CAP DUST 20 $30.90
6333803 CLAMP, T-BOLT W/SPRING 15 $41.09
6334104 SPRING 40 $11.29
6336307 SCREW HEX FLANGE HEAD CAP 20 $8.47
6336780 KIT HANDLES RAKE ADJUSTMENT 20 $28.21
6336781 KIT, RH CONTROL PANEL 20 $388.89
6337081 RELAY 24V 127 $4.82
6338131 SWITCH, HEIGHT CONTROL, DRIVER SEAT 20 $85.54
6338148 POWER SUPPLY 40 $1,243.42
6339089 FILTER ELEMENT FUEL 94 $29.40
6342574 MIRROR, BOTTOM, COVEX W/HEAT, RH 20 $38.59
6344413 BRACKET 5LB FIRE EXTINGUISHER 30 $34.46
6344419 SENSOR-KIT ABS 65 $45.77
6344611 KIT TRACK SEAT 20 $156.78
6344624 KIT SEAT CUSHION 50 $248.95
6344633 KIT HANDWHEEL RECLINE AM80 50 $14.03
6344764 SCREW CYLINDER M22 95 $16.88
6344765 JOINT BALL ASSEMBLY 95 $298.75
6344792 LATCH PIN ASSEMBLY 16 $53.76
6345178 PUMP ASSY., HYDRAULIC (INCL. MOTOR & RESERVOIR) 56 $2,532.73 634-5274 HARNESS, WIRING 30 $293.36
6346289 WASHER THRUST 95 $28.51
6346290 LOCK RING M58X1.5 95 $71.64
6347297 ROTOR-BRAKE FRONT 95 $191.06
634-7302 SPOOL, HAND ASSIST STRAP 21 $6.05
634-8001 LARGE SIGN KEY 40 $26.53
6349551 SPINDLE 80 $186.89
6349568 GLASS TOP FLAT W/SIGNAL 20 $84.43
6350889 BLOWER 24V 127 $1,031.27
6351084 HEEL PIN KIT 60 $23.44
6351463 DIPSTICK TUBE 21 $190.72
6352008 DIAL INDICATOR 37 $534.09
6352730 BUTTON ASSEMBLY PUSH WHEELCHAIR 30 $179.30
6354386 ASSY-SENSOR PNP NO 65 $143.00
6354823 SPACER 10 $33.15
36 6354832 STOPPER 30 $37.97
6356608 SUPPORT ARM ASSEMBLY 20 $185.78
6356986 SCREW, HEX FLANGE HEAD CUP 21 $3.79
6356994 PULLEY, ACCESSARY DRIVE 27 $336.08
6357846 ASSY-SENSOR LEVEL 120 $90.02
6358006 ASSEMBLY, POWER ASSEMBLY, SIDE SIGN 35 $1,352.93 6358265 FILTER-OIL SPIN ON 27 $35.19
6358351 DEPLOYMENT KIT PIVOT PLATE 17 $188.16
6358440 ASSEMBY, AIR COCK 65 $295.19
6358674 TAPESWITCH 24 INCH 20 $153.54
6359347 ROTOR-BRAKE REAR 95 $191.06
6359347NFA ROTOR-BRAKE REAR 35 $137.67
6359408 CLAMP 4" V-BAND 30 $37.65
6359969 SEAL-CRANKCASE 17 $14.48
6360254 SCREW, HEX FLANGE HEAD CAP 25 $4.46
6360285 SOLENOID KIT 20 $28.63
6360361 CYLINDER, GAS SPRING, W/C FLIP UP SEAT (100 LB) 15 $128.32 6360951 CLAMP, MUFFLER SECURING 52 $140.10
6361062 ROUND BOLT, HEX BM18 X 1.5 X 60 95 $9.18
6361067 SENSOR-KIT WEAR W/O HEATSHRINK 80 $163.52
6361068 WEAR SENSOR CABLE 95 $27.74
6361478 SIGN ID BOARD, SMART SIGN SERIES 60 $45.92
6361639 RELEASE HANDLE ASEMBLY 45 $25.46
6361865 AIR COMPRESSOR ASSEMBLY, TWIN 30 $6,829.63
6362698 CABLE, ADAPTER - CUMMINS GENDER BENDER 30 $123.62 6362761 ASSY-SENSOR LOW FLUID AMODEL 65 $326.63
6367021 KIT-PIN AND LANYARD 25 $13.17
6383349 GOVERNOR,AIR D2 @ 130PSI 20 $99.81
6387742 GASKET, STRIP 32 $48.88
6387744 RADIATOR ASSEMBLY, 48 ROW 107 $2,891.10
6387745 GASKET, STRIP 32 $25.19
6387746 GASKET, STRIP 32 $46.42
6388966 RUBBER OVERSHOE W/ TAB WINDOWS 120 $43.28
6389280 VALVE ASSEMBLY 127 $69.93
6389335 T-NUT, PIVOT CABLE, MODIFIED 30 $14.55
6391891 SENSOR, HUMIDITY 37 $508.01
6392084 SENSOR-ABS RH 95 $165.48
6392462 MODULE, CORNER LH BLACK 20 $370.74
6392463 MODULE, CORNER RH BLACK 20 $370.74
6392538 WHEEL HUB, REAR 95 $767.77
6392546 O-RING 95 $8.96
6392547 SEAL-SHAFT 132 X 160 X 10 95 $45.18
6392548 THRUST WASHER 95 $20.46
6392549 NUT, SLOTTED M100 X 1.5 95 $50.48
6394619 MODULE DISPLAY KEYPAD 100 $487.70
6394894 FINGER BOARD WITH FEMALE CONNECTOR 35 $10.12
37 6395568 HOSE 58 $17.16
6396808 HOUSING, BREATHER 35 $103.10
6396883 KIT-MAGNETIC SWITCH W/HARNESS 19 $134.20
6398340 BLANKET, FLEX PIPE TO TURBO 30 $658.57
6398984 EMERGENCY RELEASE BAR ASSEMBLY 28 $53.91
6398987 SASH LATCH 14 $15.78
6398997 SASH LATCH STRIKE 14 $16.40
6399550 SOCKET ASSEMBLY 30 $166.25
6399978 HARNESS, 48.00 LG. 64 $79.01
6403483 SEAL-RING RECTANGLE 20 $2.19
6405511 KIT-PINCH HANDLE BLACK ANODIZE 40 $98.14
6405956 SENSOR ASSEMBLY, ABS 25 $130.38
6406183 HARNESS ASSEMBLY 185 $1,206.33
6406324 BLANKET-EXH TURBO TO FLEX 37 $414.12
6406630 ASM PSB LED BOARD 35 $287.79
6407286 CONTROLLER SYSTEM ASSY 67 $821.32
6407697 CONTROLLER SYSTEM ASSY 67 $821.32
6407713 FAN, CONDENSER 325 $3,007.01
6407720 FILTER, AIR 25 $64.60
6408999 FILTER, HYDRAULIC - CARTRIDGE 17 $11.93
6409387 BUSHING, HINGE BRACKET BIKE RACK 10 $39.81
6410065 LED BOARD-23.0 LG CLEVER PROGRAM TO 100% 35 $56.91 6410067 LED BOARD-19.0 LG BASIC 35 $41.15
6410144 LED BOARD-12.0 LG BASIC 35 $30.78
6410215 BOARD-LED 21.0 LG BASIC 35 $46.81
6410733 KIT, FAN & ACCESSORY PULLEY 50 $290.69
6411505 KIT-SENSOR BRAKE W/HEATSHRINK 90 $159.58
6422025 SEAL, O-RING 30 $7.04
6423625 SEAL 37 $2.48
6424649 SCREW, HEX FLANGE HEAD CA 37 $2.60
6429748 ACTUATOR,CUMMINS 8.9 37 $846.28
6438294 TUBE, CPR WATER OUTLET 27 $142.81
6439994 PCB ASM, TRANSITION BOARD 40 $232.95
6439995 POWER SUPPLY ASM, 3.3V 50 40 $1,057.26
6443252 KIT-BRAKE PAD MARATHON AXLE-SET 60 $119.92
6444399 ACTUATOR - VALVE, COOLANT (SEE 269G9) 94 $587.48 6444514 CLUTCH, ASSEMBLY 101 $2,287.78
6444570 90MM LED HIGH BEAM HEADLAMP 50 $155.93
6446785 NU,T HEX M16 X 1.5 25 $2.07
6447270 CALIPER-BK W/O PADS FCS/RSS 95 $1,369.51
6447272 CALIPER-BK W/O PADS FSS/RCS 95 $1,369.51
6447282 BLOWER ASSEMBLY 127 $586.79
6447295 VALVE ASSEMBLY, HEATER CONTROL 127 $118.60
6447341 KIT, BRAKE PAD W/ N2G ADJUSTER 80 $195.70
6447556 LATCH, QUAD 34MM 80 $10.64
6448354 GASKET, STRIP 1/4" X 3/4" X 63.00" 32 $24.34
38 6448357 SEAL, ANGLE FOLD 3/8" X 40" 37 $46.53
6458565 ELEMENT, PRIMARY AIR FILTER 67 $100.20
6458566 ELEMENT, SECONDARY AIR FILTER 67 $69.19
6459050 CLIP-RETURN SPRING HOPPER (BAG OF 10PCS) 20 $29.95 6459523 RADIATOR ASSEMBLY 107 $1,845.81
6460006 SUPPORT ARM ASSEMBLY, INNER 23 $255.35
6460414 BLANKET, FLEX PIPE TO TURBO 35 $622.92
6460416 RETAINERS, SPRING 15 $3.84
6461992 HARNESS ASSEMBLY, PUSH BUTTON / LED 30" 65 $173.18 6461993 HARNESS ASSEMBLY, MH4 41 $756.21
6461996 CONTROLLER SYSTEM ASSY 67 $821.32
6462153 CLAMP, V BAND 40 $64.19
6466068 LED HEADLAMP KIT - GEN 2 70 $1,291.61
6466163 ASSY-FAIRING CNG CS RR 20 $767.87
6466349 LAMP-ASSY STREETSIDE 70 $645.80
6467408 TUBE, BREATHER 30 $247.91
6467692 COOLER-OIL 35 $1,499.06
6467787 ASSY-SURGE TANK 160 $1,878.40
6468766 SCREW-SOC M12X1.5X25 CL8.8 183-B1 95 $5.65
6468902 SCREW, HEX M16X1,5X40-10.9 80 $8.60
6468986 RESISTOR, 4 SPEED 127 $13.91
6469564 TRIM TOP,IP,TRANS, CLOSEOUT 84 $162.63
6473909 CATCH BAR - EMERGENCY RELEASE 40 $235.24
6474995 VALVE PRESSURE & REGULATOR 20 $1,273.76
6475004 SEATBELT KIT, 3 PT ORANGE ERGO M (AM80), 3-WIRE 20 $414.87 6475382 SEATBELT, 2 PT BLACK 20 $200.02
6477308 TAPE FOIL 20 $37.76
6477704 EXTENSION- IGNITION COIL 35 $139.16
6477944 HARNESS-WIRING ENG CONTROL 30 $3,293.79
6478677 VALVE - COOLANT 24V 57 $572.83
6479122 GAS PROP-BIKE RACK 98 $14.85
6479144 CAP-2.25" TOP VT NO VALVE PL 4"T 80 $9.29
6482309 BEARING-THRUST 60X85X17 STL CAGE 95 $79.37
6482567 RADIATOR ASSEMBLY 107 $1,909.09
6483014 O-RING- N1490/PFTE COATED 21 $0.48
6483582 COOLER-EGR 8.9 20 $2,685.42
6484941 SENSOR-COOLANT LEVEL 117 $48.46
6488746 COIL PACK 15 $263.92
6490776 HUB-ASSY BEARING W/PULSE WHEEL 95 $445.91
6492635U CORE-ABS-ECU E BASIC 24V J1939 45 $327.00
6492635X ABS-ECU E BASIC 24V J1939 45 $1,583.64
6493137 THROTTLE-CUMMINS DUAL ANALOG 140 $285.27
6493305 MODULE-ELECTRONIC CONTROL 52 $0.00
6494137 SPRING ASSY KIT-ERGO AIR 20 $147.51
6494326 BELT-WATER PUMP 27 $85.63
656315 ASSY-WIPER MTR BRKT CS 30 $198.43
709140 HORN-DUAL 90 $19.71
39 715553 ROD-LOWER REAR RADIUS WINDOWED 70 $185.41
715555 ROD-UPPER REAR RADIUS WINDOWED 70 $261.40
7700084 SENSOR-KIT WEAR W/HEATSHRINK 70 $30.33
7700158 CALIPER-FSS/RCS W/CARRIER AND SENSOR 60 $625.35 7700164 CALIPER-FCS/RSS W/CARRIER AND SENSOR 60 $625.35 7700345 PLUG-EXPANSION 25 $3.08
7700830 CLAMP-BREEZE 30 $15.67
7701005 COIL-PACK WITH EXTENDER 32 $134.00
7701006 EXTENSION-COIL IGNITION 32 $53.00
8110904 VALVE DRAIN 26 $5.02
8112361 CABLE DAMPER CONTROL 127 $9.03
8112552NFA2 BLADE-WIPER 26.0 GEN2 90 $9.92
817800 ASSY-WASHER PUMP 130 $39.84
8210211 SWITCH-PUSHBUTTON 85 $509.50
969301 LAMP-LED SIDE CONSOLE 20 $132.88
023083 BATTERY HOLD DOWN 20 $4.69
086452 PIN HITCH 1/2 X 4.5 45 $7.14
217023 SWITCH-WIPER CNTRL 24V 130 $292.87
364782 PIN-DOWEL .156 X 1.5 20 $2.40
6344604 PANEL CONTROL RH FRONT 20 $20.55
6349256 ELBOW-90DEG SILICONE 1.75 MOD 30 $59.23
6329772 KIT GAP HIDER 40 $66.00
591449 VALVE-LEVELING W/ SENSOR 80 $534.78
048922 ELBOW-MALE 20 $88.59
359218 GAS-SPRING-60LB 7.87 STROKE 70 $33.00
295629 ELBOW-SIL 90 DEG 1.38 ID 4 PLY 25 $35.22
6351583 BRAKE TREADLE 90 $161.10
133687 WIRE HAZARD MOD 3' 10 $52.41
6389245 CLAMP 21 $15.22
6307717 VALVE MAG DOOR CYLINDER ENT 65 $127.42
089034 SWITCH-LOW PRESSURE, W/C 65 $132.54
342323 ELB-90 3/8FPT x 3/8FPT SWIVEL 92 $12.80
168228 BUSBAR-12CCT PTC 35 $43.68
6391536 MODULE RESISTER 24V 157 $13.04
6311073 GASKET - NEOPRENE 37 $4.87
608031 ASSY-HOSE NOZ2-06 FL19.5 15 $19.34
6390348 HOSE, ELBOW, COOLANT, SILICONE (1-3/4") 25 $35.40 473943 BLOCK-CHAIN SPACER 20 $44.64
6391384 FITTING, 1/2" HOSE OD X 1/2" NPT 20 $37.51
430027 VALVE-MODULATOR 24 VOLT DIN CONN 89 $135.37
6367197 RELAY VALVE R14 20 $119.45
052142 CAP VENT TUBE END 48 $0.76
6360284 SEAL KIT 22 $44.14
6345456 RESISTOR 183 $11.92
020118 FTG-SOCKETLESS 3/8 MPT 40 $3.30
6403090 BLOCK, FRAME LOCATOR 21 $1.05
6342389 BLOWER ASSEMBLY 24V 127 $1,193.43
40 6341343 CONTROLLER ASSEMBLY, 24V 127 $500.23
6404150 KIT-PROXIMITY SENSOR 10 $178.91
6326718 DIPSTICK 35 $17.47
384986 HOLD DOWN-BATTERY 25 $14.50
6388114 PCB, SIGN DVR 485, CHROMA 1 110 $1,637.91
6394998 ASSEMBLY-FAN PROGRAMMED 67 $470.39
6471495 CLAMP, W/BOLT AND NUT 70 $9.39
365284 ELBOW-SILICONE 90 1.75 25 $46.90
6388696 COUPLING, SILICONE ELEMENT 23 $2,724.89
819783 CONTROLLER-BUS DOOR 5 POS 90 $454.26
571300 PUMP-BOOSTER EMP WP32 3000 RPM 217 $552.52
351231 GLASS-ENTR 72 GRN TOP AMERI 35 $63.21
6387741 CHARGE AIR COOLER ASSEMBLY 107 $966.46
6387743 GASKET, STRIP 32 $7.11
7700019 SWITCH-HEADLIGHT DIM 45 $3.74
222903 ELBOW-90 SILICON 2.0ID 50 $39.51
399298 ASSY-WIPER MTR BRKT SS 150 $440.05
6471208 MOTOR, WIPER WITH HARNESS 30 $143.92
441222 TRIM-JOINER STRIP L/D 64 $7.04
6478315 TUBE-WATER OUTLET 15 $60.30
068196 ELBOW-SILCONE 45 2.5 ID 25 $51.75
6460841 LOOM-THERM-L WRAP 36"x 1.5" ID 40 $39.58
11-08-1069 LANYARD 60 $17.35
322583 BRACKET-BELT GUARD STOP 25 $58.39
6359743 HORN BRUSH KIT 40 $86.80
6348893 KIT-POWER/CONTROL BOARDS 395 $829.80
6310736 RESISTOR - 24 VOLT 126 $9.50
6388749 ENGINE EXHAUST, ASSEMBLY 25 $684.05
6469710 LOWER COOLANT LEVEL SENSOR 20 $395.49
6344055 MOTOR ASSY, 12 V 20 $120.02
6350890 MOTOR 24V 127 $639.77
434434 ASSY-ADAPTER JACKING 30 $1,789.73
259583 ISILATOR-MUFFLER MOUNT 20 $14.50
553566 HOSE VENAIR 62 MM ID 87 $147.43
6312089NFA O-RING 85 $0.54
387427 COVER-LICENSE PLATE LIGHT 30 $60.04
8110728 SWITCH-SPST ON-NONE-OFF 50 $3.83
6353331 VALVE-RELAY BRAKE 45 $233.10
020143 BREAKER-20A ETA MAN 60 $10.14
937141 ASSY-HATCH POLYRIT W/SST 100 $853.75
41 2024-2025

LEAD TIME PRICE NEW PN
30 12.01
20 0.24
70 22.9
86 25.04
30 96
20 220.35
120 11.42
126 7.2
95 415.98
100 243.47
40 72.27
65 81.64
45 17.87
67 16.1
30 16.24
30 14.08
45 60.77
45 3.91
20 10.81
17 49.98
20 1.99
45 26.29
57 13.96
30 105.93
35 9.78
25 5
21 0.41
25 604.44
45 93.54
40 95.34
25 7.61
10 23.18
17 34.94
87 10.7
110 28.84
45 1791.96 799517
25 546.68
95 191.92
130 9.25
115 23.47
45 40.93
42 30 1.38
31 2.12
25 5.72
31 13.24
25 49.54
60 20.61
90 31.39
55 27.06
57 178.75
15 41.49
87 19.47
110 95.24
20 2.25
20 2.1
20 7.07
30 92.58
65 61.23
25 15.5
102 154.72
20 119.75
25 7.34
27 12.27
20 0.19
92 200.4
20 49.41
65 36.62
25 1.21
85 30.16
17 245.07
10 145.44
90 57.49
47 1076.76
115 10.68
115 17.99
20 171.7
35 22.5
20 13.83
50 508.15
31 4.27
60 37.51
44 0.52
37 52.6
90 63.61
90 103.51
90 12.99
60 54.1
40 592.9
43 65 9.33
30 141.2
80 62.99
43 3.86
31 1.9
35 65.32
30 617.42
20 210.54
35 53.16
50 119.61
45 295.64
103 1463.76
20 86.94
20 141.37
45 19.58
20 981.83
67 114.66
80 17.74
70 264.77
60 58.63
30 89.63
31 0.47
45 52.82
45 48.18
25 100.86
62 3.22
60 107.75
27 41.56 308521
60 274.41
45 459.78
35 31.8
42 129.12
70 60.5
97 2032.93 6498993
70 65.23
90 65.23
20 24
140 417.31
20 72.29
30 124.26
20 1.67
133 1429.69
28 60.6
49 96.97
28 1.75
147 13.01
20 484.18
44 30 26.34
63 8.96
35 86.31
55 86.4
37 0.58
31 0.47
20 3.84
20 121.26
37 16.9
90 27.79
37 440.52
50 54.21
20 2
60 67.61
45 602.22
112 81.25
65 105.25
31 3.84
164 34.93
80 53.79
60 538.59
100 316.93
112 107.22
35 27.83
65 156.23
20 45.51
20 34
20 16.67
40 127.66
20 18.03
20 147.03
20 150.18
65 112.89
30 19.67
37 2.04
37 4.06
20 52.43
20 19.49
40 738.04
170 1087.66
20 104.28
20 113.88
90 117.38
20 23.44
20 156.4
120 73.67
35 74.56
45 57 43.81
64 9.23
64 8.39
30 668.21
45 442.62
65 204.06
80 37.72
20 131.22
22 35.78
20 121.58
20 16.15
20 138.08
50 1180.74
55 220.83
150 32.06
90 11.57
90 2.32
122 146.83
105 48.09
90 34.54
27 1590.04
35 63
20 270.65
60 445.97
45 432.01
127 93.44
30 496.83
30 532.31
20 19.3
137 160.17
70 40.07
85 51.35
80 412.37
85 359.13
112 68.17
103 115.96
60 115
15 1025.6
70 709.33
20 27.4
112 43.31
85 42.77
85 38.96
62 272.83
25 102.54
23 182.94
70 25.09
46 87 32.94
31 4.42
20 329.48
87 32.96
40 14.77
70 115.28
87 47.07
87 49.4
87 28.3
35 703.02
35 1972.14
95 372.92
40 2.8
60 33.57
40 877.86
31 2.52
25 187.34
70 543.56
90 15.19
90 3.32
90 16.16
84 13.15
20 28.05
30 7.03
20 0.72
28 4.21
100 1.52
92 1.03
30 19.29
20 0.08
30 2222.93
35 8.78
120 1431.13
37 297.95
20 25.94
20 17.14
224 0.15
20 20.46
20 50.86
65 155.88
45 3768.92
52 5.37
25 1.09
215 920.56
17 25.51
80 3.27
110 133.52
47 50 70.18
80 14.63
80 19.42
20 223.25
80 461.92
25 5.73
40 57.3
20 11.91
15 6.21
21 46.59
27 22.26
32 41.22
20 30.9
15 41.09
40 11.26
20 8.47
20 28.21
20 388.89
127 5.17
35 85.54
#N/A #N/A NO REPLACEMENT
93 29.4
20 38.59
27 31.7
65 45.77
20 156.78
50 248.95
50 14.03
80 16.88
80 301.73
16 53.76
56 2532.73
30 293.36
80 28.76
80 71.64
80 191.06
21 6.05
40 26.53
80 187.96
20 84.43
127 1031.27
60 24.11
21 190.72
37 534.09
30 179.3
65 143
10 33.15
48 30 37.97
20 185.78
21 3.79
27 336.08
120 90.02
#N/A #N/A NO REPLACEMENT
27 35.19
17 188.16
65 295.19
20 153.54
80 191.06
35 137.67
30 50.28
17 14.48
25 4.46
20 28.63
15 128.32
52 140.1
80 9.18
80 163.52
80 27.74
60 45.92
45 25.46
30 6829.63
30 123.62
65 295.15
31 14.22
20 100.31
52 64.98
132 3931.94
52 33.48
52 61.71
120 43
127 72.02
30 14.55
37 544.31
80 165.48
20 389.28
20 370.74
80 767.77
80 8.99
80 45.18
80 20.54
80 50.48
100 487.7
57 9.25
49 20 17.16
35 103.1
19 134.2
30 609.79
28 53.91
14 15.78
14 16.4
30 166.25
64 79.01
20 2.35
40 98.14
25 134.96
52 1649.41
32 414.12
35 287.79
37 847.62
37 847.62
325 3007.01
25 64.6
17 11.93
10 39.81
35 52.36
35 37.86
35 28.32
35 43.07
50 312.62
120 159.58
30 7.04
37 2.48
37 2.6
37 846.28
27 142.81
40 232.95
#N/A #N/A NO REPLACEMENT
60 119.92
94 587.48
101 2287.78
45 154.93
25 2.07
80 1369.51
80 1369.51
127 604.39
127 126.9
80 195.7
80 10.64
52 32.47
50 52 69.64
67 100.2
67 69.19
20 29.95
92 2509.65
23 255.35
35 622.92
15 3.84
67 236.79
52 1033.96
37 847.62
40 64.19
47 1291.61
20 767.19
47 645.8
30 247.91
35 1499.06
160 1972.4
80 5.7
80 8.65
127 14.35
84 162.63
40 235.24
20 1273.76
20 414.87
20 200.02
20 34.96
35 139.16
30 3293.79
57 562.64
98 14.85
80 9.58
80 79.91
102 2587.33
20 0.48
20 2685.42
117 48.46
15 263.92
80 445.91
45 327
45 1583.64
140 283.44
50 6857.4 6493305X
20 147.51 6497457
27 85.63
30 198.43
90 19.71
51 70 185.41
70 261.4
70 30.33
60 625.35
60 625.35
25 2.61
30 15.67
32 134
32 53
20 5.31
127 9.3
90 9.92
130 39.84
85 509.5
27 132.88
20 4.31
45 11.75
130 292.87
20 3.1
20 19.03
30 59.23
40 66
80 534.78
20 87.46
70 33
25 35.89
90 161.1
10 52.41
21 15.22
65 127.42
65 132.54
92 13.04
35 43.68
157 13.44
37 4.87
20 19.34
25 35.4
30 44.35
25 34.73
112 128.13
20 121.24
48 0.76
20 44.14
183 12.29
40 3.37
21 1.05
127 1193.43
52 127 500.23
10 178.91
35 17.47
25 14.41
110 1637.91
47 500.26
70 9.39
25 47.8
23 2942.88
90 454.26
42 597.32
35 63.21
102 1312.94
52 9.45
120 5.04
50 40.27
150 438.5
30 143.92
64 7.04
15 60.3
25 52.73
40 39.58
60 17.35
25 58.02
40 86.8
395 819.21
126 9.8
25 684.05
20 363.85
30 120.02
127 678.15
30 1843.43
20 15.66
87 147.43
85 0.54
30 59.65
50 3.83
45 233.1
60 10.14
90 853.75
53 City of Torrance | Finance Department, Purchasing Division | (310) 618-5820 | [email protected] Procurement Request - Revised 11/04/23

PROCUREMENT REQUEST FORM
Finance Department, Purchasing Division

Purchase Information
PRF#: 33136 Department: Transit Project Manager: Caballero, Ana Purchase Type: Exception Category: Commodity
Est. Annual Expenditure: Prior PO or Contract # (if any): Anticipated Dates:

Start
Start
Over $250K 2024-00000721 Start: 2/21/2025 End: 2/20/2028 Quote Amt: 600000.00 Proposed Vendor: Aftermarket Parts Co, LLC DBA New Flyer Parts Project Title: New Flyer Bus Parts
Description Summary: Justification for purchase / Timing Considerations / Impact if not approved / Analysis of bid or RFP.

Scope of Work: Provide new and remanufactured OEM bus parts for New Flyer buses (GE40FLR, C40FLR & XN40-Xcelsior) on an as requested basis to the Torrance Transit, Fleet Services Division. Term: 02/21/25- 02/20/28 Annual Expenditure: $600,000.00 Total NTE Expenditure: $1,800,000.00 Exception (if applicable): Competition doesn't reasonably exist (sole source) Exception Description (if applicable):

The Aftermarket Parts company branded as NFI Parts is the O.E.M supplier of customized heavy-duty coach/ transit bus parts for the NFI Group Inc branded coaches/buses.

Please see single source affidavit letter attached.
54 ATTACHMENT 4
City of Torrance | Finance Department, Purchasing Division | (310) 618-5820 | [email protected] Procurement Request Form - Revised 11/04/23
Approvals
Project Manager
•I certify that I do not and will not have conflict of interest, personal or organizational, real or apparent in participating in this procurement.

Action: Caballero, Ana Approve on 1/8/2025 11:58:18
Comments:

Department Manager
•I certify that I do not and will not have conflict of interest, personal or organizational, real or apparent in participating in this procurement.

Action: Estrada, Art Approve on 1/8/2025 14:24:53
Comments:

Department Director
Action: Offoegbu, Godfrey Approve on 1/9/2025 9:16:15
Comments: Godfrey Offoegbu, For Kim Turner
IT Manager
Action: N/A
Comments:

Purchasing
Action: Benjamin, Turquoise Approve on 1/13/2025 12:37:13 Comments: Vendor is the representative reseller
Finance Approver
Action: Pham, Joseph Approve on 1/13/2025 16:28:37
Comments:
55