Agenda — Dinuba City Council, March 28, 2023 (part 1 of 3)

Tuesday, March 28, 2023 / 6:30 PM / City Hall / 405 East El Monte Way, Dinuba District 1
Rachel NerioGuerrero
Vice Mayor
District 2
Maribel Reynosa
Mayor
District 3
Benjamin Prado
Council Member
District 4
Kuldip Thusu
Council Member
District 5
Linda Launer
Council Member
All attendees are advised that electronic devices should be placed on silent upon entering the Council Chambers.

The City Council will take action on all items listed on the agenda.

1. OPENING CEREMONIES

1.1. Welcome and Call to Order

1.2. Invocation

1.3. Pledge of Allegiance

2. AGENDA CHANGES OR DELETIONS
To better accommodate members of the public or convenience in the order of presentation, items on the agenda may not be presented or acted upon in the order listed. Additions to Agenda may be added only pursuant to California Government Code section 54954.2(b).

3. REQUEST TO ADDRESS COUNCIL
This portion of the meeting is reserved for any person who would like to address the Council on any item that is not on the agenda. Please be advised that State law does not allow the City Council to discuss or take any action on any issue not on the agenda. The City Council may direct staff to follow up on such item(s). Speakers are limited to three (3) minutes. If there is any person wishing to address the City Council at this time please approach the podium and state your name and nature of the request.

4. CONSENT CALENDAR
Matters listed under the Consent Calendar are considered routine and will be enacted by one motion and one vote. There will be no separate discussion of these items. If discussion is desired, a member of the audience or a Council Member may request an item be removed from the Consent Calendar and it will be considered separately.

4.1. SUBJECT
Notice of Completion - College Ave. Streetlights Project (JW) a

RECOMMENDATION
Council accept the College Avenue Streetlights Project as complete and authorize the City Engineer to file a Notice of Completion with the Tulare County Recorder's Office.
a

4.2. SUBJECT
Dinuba Chamber of Commerce "Earth Day" Golf Tournament
Sponsorship (DJ)
a

RECOMMENDATION
Council approve Gold Level sponsorship in the amount of $1,000 for the Dinuba Chamber of Commerce "Earth Day" Golf Tournament on April 21, 2023. a

4.3. SUBJECT
Appointments to the City of Dinuba Planning Commission (MA) a

RECOMMENDATION
Council to reappoint Linda Faust (District 3) and Tim Conklin (District 5) to the Dinuba Planning Commission to an additional three-year term from January 1, 2023 to December 31, 2025.
a

4.4. SUBJECT
Approval of City Council Meeting Minutes (MA)
a

RECOMMENDATION
Council to review and approve City Council meeting minutes of March 14, 2023 as presented.
a

4.5. SUBJECT
Resolution No. 2023-18, Authorization to Execute Program Supplement for Construction of the Roadway Segment Safety Improvements Project (IH)
a

RECOMMENDATION
Council adopt Resolution No. 2023-18 authorizing the City Manager or designee to execute the Program Supplement Agreement and future Program Supplement Agreements with the California Department of Transportation (Caltrans) for the Roadway Segment Safety Improvements Project.
a

4.6. SUBJECT
Resolution No. 2023-19 Approving a Budget Amendment in the amount of $1,436,020.29 and Authorization to Purchase a New Fire Ladder Truck (JORW)
a

RECOMMENDATION
Council to taking the following actions by one motion and one vote:

1. Approve Budget Amendment No. 2023-15 budgeting $1,436,020.29 in the FY 2022-23 budget for the acquisition of a new fire ladder truck; and,

2. Authorize staff to order the new fire ladder truck through the Houston-Galveston Area Council (HGACBuy) Purchasing Cooperative; and,

3. Authorize staff to execute any related documents and agreements associated with the purchase of the new fire ladder truck.
a

4.7. SUBJECT
Parks Use Fee Waiver for Blessing of the Bikes and Cars 2023 Event at Rose Ann Vuich Park (SH)
a

RECOMMENDATION
Council approve the use of Rose Ann Vuich Park to Unity Crew for the "Blessing of the Bikes and Cars" event and waive the park rental fee in the amount of $440. a

5. WARRANT REGISTER

5.1. SUBJECT
Warrant Register March 17 & 24, 2023 (KS)
a

RECOMMENDATION
Council to review and approve the Warrant Register as presented. a

6. PUBLIC HEARING

6.1. SUBJECT
Public Hearing to consider a redesign of the previously-approved Montebella Tentative Subdivision Map (Application 2023-01) on 28.8 acres located on the west side of Englehart Avenue, north of the Saginaw Avenue alignment. (KSch)
a

RECOMMENDATION
City Council conduct a public hearing and adopt the following:

1. Resolution No. 2023-15 (Attachment “A”) approving an amendment to the site’s General Plan land use designation.

2. Introduce and conduct the first reading, waive reading in full, of the Ordinance No. 2023-03 (Attachment “B”) approving a zone change to adjust existing zoning designations on the site.

3. Resolution No. 2023-16 (Attachment “C”) approving an amendment for the design of the Tentative Subdivision Map to increase the number of single family lots from 100 to 123 and revise the size and design of a proposed onsite neighborhood park/temporary stormwater ponding basin.

4. Set April 11, 2023 for the second reading of Ordinance No. 23-##. a

6.2. SUBJECT
Public Hearing to consider an application for a Planned Unit Development Tentative Subdivision Map for 27 Single Family Residential lots on a 5.5- acre site south of Kamm Avenue. (KSch)
a

RECOMMENDATION
City Council conduct a public hearing and adopt the following:

1. Resolution No. 2023-17 (Attachment “A”) approving a Vesting Tentative Subdivision Map to create 27 single family residential lots and adoption a Categorical Exemption as the environmental finding for the project. a

7. DEPARTMENT REPORTS

7.1. SUBJECT
Approval of Education and Training Affiliation Agreement between the City of Dinuba and Valley Regional Occupation Program (VROP) and Adoption of Resolution No. 2023-14 Approving a Budget Amendment to Fund the Fire Training Facility in FY 2022-23 (JORW)
a

RECOMMENDATION
Council to take the following actions by one motion and one vote:

1. Approve the Education and Training Affiliation Agreement between the City of Dinuba and Valley Regional Occupational Program and authorizing the City Manager or designee to execute the agreement; and,

2. Adopt Resolution No. 2023-14 approving budget amendment No. 2023-14 allocating $400,000 from the Ambulance Fund for the project in the FY 2022-23 budget.
a

8. MAYOR/COUNCIL REPORTS

9. CITY MANAGER COMMUNICATIONS

10. CITY STAFF COMMUNICATIONS

11. ADJOURNMENT
This agenda was posted at least 72 hours prior to the regular meeting per GC Section 54954.2(a). A Citizens' Packet regarding this meeting is available at the City Clerk's Office located at City Hall, 405 East El Monte Way, Dinuba CA 93618.

In compliance with the Americans with Disabilities Act, if special assistance is needed to participate in the meeting, please contact the City Clerk's Office at 559-591-5900. Please provide at least 48 hours notification prior to the meeting to allow staff to make reasonable arrangements. (28 CFR 35.102-35.104 ADA Title II)
559.591.5900 / FAX 559.591.5902 . e-mail address: [email protected]. www.dinuba.org City Council Staff Report
Department: ENGINEER/PLANNING March 28, 2023
To: Mayor and City Council
From: Jason Watts, City Engineer
Subject: Notice of Completion - College Ave. Streetlights Project (JW)

RECOMMENDATION
Council accept the College Avenue Streetlights Project as complete and authorize the City Engineer to file a Notice of Completion with the Tulare County Recorder's Office.

EXECUTIVE SUMMARY
St. Francis Electric, LLC completed the College Avenue Streetlights Project on March 20, 2023. The project costs with one change order totaled $192,578.07. This project was 100% funded by the Federal Highway Administration. The project consisted of the installation of four streetlights near existing crosswalks at the intersections of College Avenue and M St., College Avenue and Golden Way, College Avenue and San Joaquin Valley Railroad (SJVRR) Crossing, and College Avenue and Uruapan Way. Staff is requesting that the Council accept the project as complete and authorize the City Engineer to file the Notice of Completion with the Tulare County Recorder's Office.

OUTSTANDING ISSUES
None.

DISCUSSION
The City of Dinuba approved the installation of four streetlights near existing crosswalks along College Avenue in order to improve pedestrian and vehicular visibility around the railroad crossing.

The College Avenue Streetlights Project was awarded to St. Francis Electric, LLC on February 8, 2022. The project experienced delays due to PG&E staff not being able to install their facilities in a timely manner. The total project costs were $192,578.07, which included one change order in the amount of $7,578.07.

The only change order on the project was for a change of material on the electrical enclosure from galvanized steel to stainless steel. City Staff has noticed issues with the longevity of galvanized steel enclosures and elected to change the enclosure to stainless steel to lower maintenance costs for the life of the enclosure.

St. Francis Electric did an outstanding job installing the streetlights. Staff was very pleased with their work, professionalism, and responsiveness during construction.

The contractor completed the work on March 20, 2023. A picture of the completed work is shown as Attachment 'B'.

The Public Works Inspector conducted final inspections on the project and determined that the work was completed in compliance with all approved plans and specifications. The final step is for the city to accept the project as complete and file a Notice of Completion with the Tulare County Recorder's Office. Pursuant to industry standards, the city withheld a 5% contract retention on all invoices received.

The retention amount will be released after the Notice of Completion (NOC) is recorded. A copy of the NOC is enclosed as Attachment 'A'.

FISCAL IMPACT
The project totaling $192,578.07 was fully funded by the Federal Highway Administration.

PUBLIC HEARING
None.

ATTACHMENTS:

Description
A. Notice of Completion
B. Picture of Work Completion
1 RECORDING REQUESTED
AND RETURN TO:

CITY OF DINUBA

PUBLIC WORKS DEPARTMENT
405 E. EL MONTE WAY
DINUBA, CA 93618
No Fee per Government Code 6103

N O T I C E O F C O M P L E T I O N
NOTICE IS HERE BY GIVEN:

1. That the City of Dinuba, a Municipal Corporation, whose address is 405 E. El Monte Way, Dinuba, California, is the owner of the real property, public works or structure hereinafter described.

2. That on the 20th of March 2023, a work of improvements on real property hereinafter described was completed pursuant to a Contract to which Chapter 5 of Part I of Division 5, of the Public Contract Code applies.

3. That the name of the Contractor who performed said work of improvements pursuant to said Contract with the City of Dinuba is St. Francis Electric, LLC. The surety is Everest National Insurance Company, a New York insurance company, 461 5th Avenue, 4th Floor, New York, NY,.

4. That the real property or public works or structure is described as follows:

City of Dinuba
College Avenue and SJVRR Crossing Streetlight Improvements Project Federal Project No. STPLR-7500(264)
The project involved the installation of 4 streetlights.

5. That the Nature of the owner’s interest or estate is: In Fee Dated: ___________________________, 2023

CITY OF DINUBA
A Municipal Corporation

By _________________________________
Jason Watts, PE Dinuba City Engineer

2 STATE OF CALIFORNIA )
) SS

COUNTY OF TULARE )
Subscribed and sworn to (or affirmed) before me this _____ day of _______________, 2023, by Jason Watts, City Engineer of the City of Dinuba, a Municipal Corporation, proved to me on the basis of satisfactory evidence to be the person who appeared before me.

_______________________________________
Notary Public in and for the County of Tulare,
State of California
A notary public or other officer completing this certificate verifies only the identity of the individual who signed the document to which this certificate is attached, and not the truthfulness, accuracy, or validity of that document.

City Council Staff Report
Department: CITY MANAGER'S OFFICE March 28, 2023
To: Mayor and City Council
From: Daniel James, Assistant City Manager
Subject:

Dinuba Chamber of Commerce "Earth Day" Golf Tournament
Sponsorship (DJ)

RECOMMENDATION
Council approve Gold Level sponsorship in the amount of $1,000 for the Dinuba Chamber of Commerce "Earth Day" Golf Tournament on April 21, 2023.

EXECUTIVE SUMMARY
The Dinuba Chamber of Commerce holds an annual golf tournament at Dinuba Ridge Creek Golf Course as one of its fundraisers. The City of Dinuba supports the annual Chamber of Commerce golf tournament and hereby requests that the City Council approve a Corporate Champion Sponsorship in the amount of $1,000.

OUTSTANDING ISSUES
None.

DISCUSSION
The Chamber of Commerce will host the 14th annual golf tournament at Ridge Creek Golf Course. The 2022 tournament is scheduled to be held on Friday, April 21, 2023.

The Chamber of Commerce works to promote local businesses and community events. The Chamber actively promotes partnerships between businesses, local government and the community working toward a prosperous and thriving community.

Proceeds from the golf tournament help fund the Chamber's efforts to further these activities.

The City participates annually toward the annual Chamber of Commerce Golf Tournament and has participated at various sponsorship levels, as well as with City teams.

This year there are six (6) sponsorship levels as listed below. Attachment 'A' details further each sponsorship level. Staff recommends that the Council approve a $1,000 Silver level sponsorship for the annual Dinuba Chamber of Commerce golf tournament.

Title Sponsor - $2,500
Clubhouse Sponsor - $1,500
Corporate Champion Sponsor - $1,000
Cart Sponsor - $750
Game Sponsor - $500
Hole Sponsor - $150
The City participates in other golf tournaments for similar organizations and local nonprofits. Staff recommends that the Council approve a $1000 Corporate Champion sponsorship for the annual Dinuba Chamber of Commerce "Earth Day" Golf Tournament.

FISCAL IMPACT
The City's FY 2023-2023 Community Grants / Miscellaneous Fund was budgeted at $10,000 and currently there remains a balance of $6,850 for requests such as this.

PUBLIC HEARING
None required.

ATTACHMENTS:

Description
A. Dinuba Chamber of Commerce Golf Tournament

City Council Staff Report
Department: CITY CLERK March 28, 2023
To: Mayor and City Council
From: Maria Alaniz, City Clerk/Human Resources Director Subject: Appointments to the City of Dinuba Planning Commission (MA)

RECOMMENDATION
Council to reappoint Linda Faust (District 3) and Tim Conklin (District 5) to the Dinuba Planning Commission to an additional three-year term from January 1, 2023 to December 31, 2025.

EXECUTIVE SUMMARY
Commissions Faust and Conklin submitted a request for reappointment to the Dinuba Planning Commission. If the Council elects to reappoint the commissioners, each will serve a term of three (3) years from January 1, 2023 to December 31, 2025.

OUTSTANDING ISSUES
None.

DISCUSSION
The Planning Commission (PC) was established to advise the City Council on planning development. The Dinuba PC is comprised of five (5) members and is considered "quasi-judical".

Commissions Linda Faust (District 3) and Tim Conklin (District 5) have submitted a request for reappointment to serve an additional three (3) year term on the Planning Commission (Attachments 'A' and 'B' respectively). Their current terms will end December 31, 2025. Staff requests that the Council consider appointing Faust and Conklin to the Dinuba Planning Commission for three-year terms respectively beginning January 1, 2023 to December 31, 2025.

FISCAL IMPACT
None.

PUBLIC HEARING
None required.

ATTACHMENTS:

Description
A. Linda Faust Request for Reappointment
B. Tim Conklin Request for Reappointment

City Council Staff Report
Department: CITY CLERK March 28, 2023
To: Mayor and City Council
From: Maria Alaniz, City Clerk/Human Resources Director Subject: Approval of City Council Meeting Minutes (MA)

RECOMMENDATION
Council to review and approve City Council meeting minutes of March 14, 2023 as presented.

EXECUTIVE SUMMARY
None.

OUTSTANDING ISSUES
None.

DISCUSSION
None.

FISCAL IMPACT
None.

PUBLIC HEARING
None required.

ATTACHMENTS:

Description
City Council Meeting Minutes, March 14, 2023
March 14, 2023

MINUTES
COUNCIL MEMBERS PRESENT:

Nero-Guerrero, Reynosa, Launer, Prado, Thusu
COUNCIL MEMBERS ABSENT:

None.

STAFF MEMBERS PRESENT:

Alaniz, Hernandez, Hurtado, Iriarte, James, Montejano, Patlan, Solis, Watts, Yanez

1. OPENING CEREMONIES

1.1. Welcome and Call to Order
Mayor Reynosa called the meeting to order at 6:31 p.m.

1.2. Invocation
The invocation was led by Chaplain Garcia.

1.3. Pledge of Allegiance
The pledge of allegiance was led by Council Member Thusu.

None.

3. PRESENTATIONS/CEREMONIAL MATTERS

3.1. Mid-Year Update from Airica de Oliviera, Tulare County Economic Development Corporation
Airica de Oliviera and Sam Diaz with Tulare County Economic Development Corporation (TCEDC) expressed their excitement and honor to represent the County of Tulare. De Oliviera stated that the Tulare County Economic Development Corporation is a nonprofit 501c4 and led by twenty-six Board of Directors. The Board's vision is to be the premier location in California to live, learn, work, and play. De Oliviera shared that their key activity is hosting a demographic database on their website. De Oliviera reported the City of Dinuba is a prime example in that they have the largest food manufacture in the county which is Ruiz Foods. De Oliviera shared that she had met with City Manager Patlan and Assistant City Manager James to discuss great opportunities of upcoming projects and the vision they have for the current fiscal year to locate and expand business in Dinuba. De Oliviera shared information about the leads and their projects.

Council Member Thusu thanked them for doing a great job for County and Dinuba. Thusu asked how many leads have shown interest in Dinuba. De Oliviera advised that Dinuba is always at the forefront of conversations. Thusu inquired on what can be done to attract development. De Oliviera advised that creative incentives are an option to help generate business.

Council thanked de Oliviera and Diaz for the presentation.

4. REQUEST TO ADDRESS COUNCIL
This portion of the meeting is reserved for any person who would like to address the Council on any item that is not on the agenda. Please be advised that State law does not allow the City Council to discuss or take any action on any issue not on the agenda. The City Council may direct staff to follow up on such item(s). Speakers are limited to three (3) minutes. If there is any person wishing to address the City Council at this time please approach the podium and state your name and nature of the request.

None.

5. CONSENT CALENDAR
Matters listed under the Consent Calendar are considered routine and will be enacted by one motion and one vote. There will be no separate discussion of these items. If discussion is desired, a member of the audience or a Council Member may request an item be removed from the Consent Calendar and it will be considered separately.

5.1. SUBJECT
Authorization to Execute an Agreement with Tulare County for the Extension of Water Facilities (JW)
a

RECOMMENDATION
Council to approve the City of Dinuba Water Main Extension Agreement with Tulare County authorizing the City to include the extension of a water main as part of the Alta/Kamm Avenue Roundabout and authorize the City Manager or designee to execute the agreement, and any related documents.

5.2. SUBJECT
Resolution No. 2023-13 Acquisition of Right of Way for the Kamm/Alta Avenue Roundabout (JW)
a

RECOMMENDATION
Council adopt Resolution No. 2023-13 by one motion for the following action:

1. Accepts the Irrevocable and Perpetual Offer of Dedication for Right-of- Way dedication for Public Street Purposes.

5.3. SUBJECT
Approval of City Council Meeting Minutes (MA)
a

RECOMMENDATION
Council to review and approve City Council meeting minutes of February 28, 2023 as presented.

5.4. SUBJECT
Co-Sponsorship of the Leadership Class of Northern Tulare County Annual Cinco de Mayo (JB)
a

RECOMMENDATION
Council to approve co-sponsorship of the Cinco de Mayo event at Rose Ann Vuich Park on May 3-6, 2023, and the parade downtown on May 6, 2023, hosted by the Leadership Class of Northern Tulare County.

A motion was made by Council Member Launer, second by Council Member Thusu, to review and approve the Consent Calendar as presented.

Ayes: Launer, Nerio-Guerrero, Prado , Reynosa, Thusu

6. WARRANT REGISTER

6.1. SUBJECT
Warrant Register for March 3 & 10 2023 (KS)
a

RECOMMENDATION
Council to review and approve the Warrant Register as presented.

A motion was made by Council Member Thusu, second by Council Member Launer, to review and approve the Warrant Register as presented.

Ayes: Launer, Nerio-Guerrero, Prado , Reynosa, Thusu

7. DEPARTMENT REPORTS

7.1. SUBJECT
Overview of Citywide User Fee Update and Council Discussion (KS) a

RECOMMENDATION
Council to receive, review and provide feedback for the Citywide User Fee Update.

Administrative Services Director Solis presented Tony Thrasher, Project Manager with Wildan Financial Services. Solis stated she wanted to present the study before the public hearing to receive feedback from Council. Thrasher presented an overview of the citywide user fee update. Thrasher stated that the study is meant to determine the full costs incurred that support the various activities for which the City charges user fees. Thrasher advised that city staff provided input and closely evaluated costs. Thrasher shared that these are operational costs for providing services and do not include taxes or impact fees and the study results determined that the city is currently not charging the full cost of service.

Council Member Launer asked if the city was in line with other communities.

Thrasher advised that Dinuba service fees are low. City Manager Patlan advised we have established incentives that subsidize fees.

Solis reported that it is unknown when the last study was performed, there was an ordinance passed in 1992 and rates have been increased by CPI annually. Solis also informed Council that the building and impact fees were re-evaluated in 2019.

Council Member Thusu thanked city staff for the work put into the study. Thusu asked how the study's figures will impact operations in the next 5 or 10 years.

Thrasher advised that the use of a CPI is a valid calculation rate to use as an inflator. Thrasher reported that the industry standard for a revenue vs cost study is 3-5 years.

Mayor Reynosa thanked Thrasher and the city staff for their work.

7.2. SUBJECT
Local Agency Formation Commission (LAFCO) Board Small City Representative Nomination (MA)
a

RECOMMENDATION
Council to recommend a representative to the Local Agency Formation Commission (LAFC) City Selection Committee as a "small city" representative on the LAFCO Board.

City Clerk/Human Resources Director Alaniz presented to the Council the need to nominate a representative to serve on the Local Agency Formation Commission (LAFCO) City Selection Committee as a "small city" representative for the term ending May 2027.

Mayor Reynosa was selected to serve on the board.

A motion was made by Council Member Thusu, second by Council Member Launer, to nominate a representative to serve on the Local Agency Formation Commission (LAFC) City Selection Committee as a "small city" representative.

Ayes: Launer, Nerio-Guerrero, Prado , Reynosa, Thusu

7.3. SUBJECT
First Annual Dinuba BBQ Fest (SH)
a

RECOMMENDATION
Council to consider adopting registration and event fees and allowing craft breweries for the first annual Dinuba BBQ Fest at Rose Ann Vuich Park on August 4th and August 5th.

Parks and Community Services Director Hurtado presented details on the first annual BBQ Fest that is scheduled for August 4th and 5th at Rose Ann Vuich Park. Hurtado shared that this is the first event with Kansas City BBQ in this area and anticipates 20-30 participants for the first year. Hurtado shared that the BBQ competition will be judged by Kansas City BBQ judges. Hurtado stated she is seeking approval from the City Council to permit beer tasting and to set registration and sponsorship fees for this new event.

Mayor Reynosa asked if there would be a beer garden. Hurtado advised, that for now, the city is only selling a passport for beer tasting that includes a tasting glass but is open to working with a nonprofit to run a beer garden with conditions in place.

Council Member Thusu asked what the event will cost to execute. Hurtado did not have a cost at this time. City Manager Patlan advised that advertising will most likely be the highest cost.

Council expressed its approval of the event and believes it is a good opportunity to market Dinuba.

A motion was made by Council Member Launer, second by Council Member Prado , to adopt registration and event fees and allow craft breweries for the first annual Dinuba BBQ Fest at Rose Ann Vuich Park on August 4th and August 5th.

Ayes: Launer, Nerio-Guerrero, Prado , Reynosa, Thusu

8. MAYOR/COUNCIL REPORTS
Council Member Prado reported attending the Parks and Recrecreation basketball finals. Prado asked for prayers for students and family of a former student of Dinuba Unified School District who passed away on Sunday.

Vice Mayor Nerio-Guerrero advised she attended several scheduled meetings, including the Council of Cities General Meeting, the in-person Ethics training, and Friday's Goal Setting.

Council Member Launer reported attending the TCAG training which went over funding and budgeting. Launer thanked Fire Chief Webster for giving her a ride-along tour of the flooded areas. Launer reported that the City's Goal Setting was informative.

Council Member Thusu thanked Public Works, Police and Parks and Recreation staff for their hard work during the storms. Thusu reported that he will attend a morning meeting in Bakersfield on the 17th. Thusu shared that he attended the Women's Club Luncheon today.

Mayor Reynosa reported attending the Council of Cities, the city's Goal Setting, and the Women's Club Luncheon. Reynosa thanked Public Works Director Hernandez for taking her around to see the city's problem areas. Reynosa thanked the Public Works staff for assisting Cutler with their flooding. Reynosa asked that an event center be added to the city goals.

9. CITY MANAGER COMMUNICATIONS
City Manager Patlan shared that there will be an Alta Historical Society Luncheon this Thursday in appreciation of City Staff. Patlan thanked the Council for participating in the City's Goal Setting. Patlan thanked Public Works and Parks and Community Service staff for working to ensure flooding is mitigated. Patlan shared that there will be a poststorm staff meeting to identify areas that have flooded and possibly request reimbursement through FEMA.

10. CITY STAFF COMMUNICATIONS
Assistant City Manager James shared that he has received positive feedback from the pictures posted to social media of Public Works assisting with flooding in the Cutler area. James shared that the façade improvement program is in its second round of participants. James advised that there will be a discussion about the two-hour parking downtown, per the council's request.

Administrative Services Director Solis shared that the March delinquent water turn off's have been postponed due to Public Works staff working on storm issues.

City Attorney Yanez shared a reminder to complete the required training and shared that he is available for any ethics questions if needed.

Fire Chief Webster shared that his department has been busy with the storm. Webster shared that an engine was sent to assist Tulare County with flooding and has spent the day at Lake Success. Webster shared that staff has spent the week preparing with Public Works and attending preparedness meetings. Webster shared that the City of Visalia and the City of Porterville have issued a state of emergency and the Dinuba Memorial Building has been identified as a temporary evacuation point for the north county. Webster advised that the Dinuba Family Resouce Center has been identified as a drop-off location for supplies. Webster shared that the two Battalion Chiefs interviewed the five candidates for Firefighter/EMT B position and will soon be making conditional offers of employment.

Police Chief Iriarte reported that four Reserve Officers will start employment on April 3rd. Iriarte shared that the department is participating in the Fresno State and Reedley College Job Fairs.

Parks and Community Service Director Hurtado thanked the council for approving the First Annual Dinuba BBQ event fees. Hurtado shared that the baseball draft is happening tonight and that the CDBG senior meals grant award will be announced in March.

City Engineer Watts shared that Englehart will close for the installation of sewer and water for the Vineyard Estates subdivision and that all notices have been made. Watts advised that he is busy working through plans, Road 74 bids are ongoing, the Entertainment Plaza restroom project is out to bid and striping around town is in progress.

Public Works Director Hernandez thanked the council for their support. Hernandez gave a brief overview of grant awards and the improvement projects, including safety improvements to pedestrian crossings and sidewalk enhancements. Hernandez announced the award of the 9 million dollar grant that will be used to support Dinuba's groundwater sustainability and provide funding for three to five new wells.

11. ADJOURNMENT
The meeting was adjourned at 8:04 pm
City Council Staff Report
Department: PUBLIC WORKS March 28, 2023
To: Mayor and City Council
From: Ismael Hernandez, Public Works Director
By: Elva Patino, Fiscal Analyst II
Subject:

Resolution No. 2023-18, Authorization to Execute Program Supplement for Construction of the Roadway Segment Safety Improvements Project (IH)

EXECUTIVE SUMMARY
The City was awarded a Highway Safety Improvement Program (HSIP) grant in the amount of $1,325,070 for the Roadway Segment Safety Improvements Project. The Project will improve pedestrian safety by narrowing the street width to promote slower vehicle speeds in the subject areas. A Program Supplement Agreement must be executed in order to commence the project's construction phase.

OUTSTANDING ISSUES
None.

DISCUSSION
Resolution No. 2023-18 (Attachment "A") authorizes City staff to execute a Program Supplement Agreement for the construction of the Roadway Segment Safety Improvements Project.

On December 18, 2018, the City was awarded $1,325,070 in Federal HSIP funds for the Roadway Segment Safety Improvements Project (Attachment "B"). The scope of work includes installing flush median, edge line and center line striping. In addition, the project will include Class II and Class III bicycle facilities to promote slower vehicle speeds at various locations along Alta Avenue, Crawford Avenue, El Monte Way, Saginaw Avenue, Kamm Avenue, Kern Street, Nebraska Avenue, Englehart Avenue, Surabian Drive and Sequoia Drive.

The City must execute a Program Supplement Agreement (Attachment "C'") in order to begin the construction phase of the project. Adoption of Resolution No. 2023-18 will authorize execution of the agreement as required by the Federal HSIP grant.

There is a required match in the amount of $977,676.25 which will be funded by local funds with an estimated project total of 2,302,756.25.

FISCAL IMPACT
Grant funds available for construction are $1,325,070. A local match of $977,676.25 is required and will be funded using local funds.

PUBLIC HEARING
None.

ATTACHMENTS:

Description
A. Resolution 2023-18
B. Award Letter
C. Program Supplement
RESOLUTION NO. 2023-18

A RESOLUTION OF THE CITY COUNCIL OF THE CITY OF DINUBA, CALIFORNIA,

AUTHORIZING THE CITY MANAGER OR PUBLIC WORKS DIRECTOR TO

EXECUTE ALL RELATED PROGRAM SUPPLEMENT AGREEMENTS UNDER THE

MASTER AGREEMENT WITH THE STATE OF CALIFORNIA DEPARTMENT OF TRANSPORTATION FOR PROJECT HSIPL-5143(034) ON BEHALF OF THE CITY WHEREAS, the City of Dinuba is eligible to receive Federal and/or State funding for certain transportation projects, through the California Department of Transportation; and WHEREAS, the Program Supplement Agreement prepared by the California Department of Transportation need to be executed with the State of California Department of Transportation before such funds can be claimed; and
WHEREAS, the City of Dinuba wishes to delegate authorization to the City Manager or the Public Works Director of the City of Dinuba to execute Program Supplement Agreement No.

F022 Rev 1 for Project No. HSIPL-5143 (034) for the Roadway Segment Safety Improvements Project, and future Program Supplement Agreements and/or amendments thereto with the California Department of Transportation.

NOW, THEREFORE, THE CITY COUNCIL OF THE CITY OF DINUBA
HEREBY, finds, orders and resolves as follows:

1. The above recitals are true and correct.

2. Program Supplement F022 Rev. 1 by and between the City of Dinuba and the State of California, Department of Transportation is approved.

3. The City Manager or the Public Works Director is hereby authorized to execute the Program Supplement Agreement and future Program Supplement Agreements on behalf of the City.

THEREFORE BE IT RESOLVED that this resolution is adopted and approved by the City Council of the City of Dinuba on this 28th day of March, 2023 by the following vote:

AYES: NOES:

ABSTAIN: ABSENT:

ATTEST:

By: _______________________________ _________________________________

MAYOR CITY CLERK

F022 Rev. 1
FOR FEDERAL-AID PROJECTS NO 06-5143F15
0619000219
March 15, 2023
06-TUL-0-DBA
HSIPL-5143(034)
5143
This Program Supplement hereby adopts and incorporates the Administering Agency-State Agreement for Federal Aid which was entered into between the Administering Agency and the State on 06/03/2016 and is subject to all the terms and conditions thereof. This Program Supplement is executed in accordance with Article I of the aforementioned Master Agreement under authority of Resolution No. approved by the Administering Agency on (See copy attached).

The Administering Agency further stipulates that as a condition to the payment by the State of any funds derived from sources noted below obligated to this PROJECT, the Administering Agency accepts and will comply with the special covenants or remarks set forth on the following pages.

Various Locations along Alta Ave, Crawford Ave, El Monte Way, Saginaw Ave, Kamm Ave, Kern Street, Nebraska Ave, Englehart Ave, Surbian Drive, adn Sequoia Drive.

Install flush median, edgeline and centeline, and Class II and Class III bicycle facilities.

0.0(MILES)
Estimated Cost Federal Funds Matching Funds
YS70 $1,325,070.00
ZS30 $279,000.00

CITY OF DINUBA
By ________________________________ By ________________________________ Title _______________________________
Date _______________________________
Attest _______________________________ Date _______________________________ Division of Local Assistance
I hereby certify upon my personal knowledge that budgeted funds are available for this encumbrance:

Accounting Officer _______________________ Date _______________ PROGRAM SUPPLEMENT NO.
to

ADMINISTERING AGENCY-STATE AGREEMENT
Adv. Project ID Date:

Location:

Project Number:

E.A. Number:

Locode:

PROJECT LOCATION:

TYPE OF WORK: LENGTH:

LOCAL OTHER
$2,612,756.25 $1,008,686.25 $0.00
Chief, Office of Project Implementation

STATE OF CALIFORNIA
Department of Transportation
$1,604,070.00
Program Supplement 06-5143F15-F022-R1- 1Page of 7
03/15/2023

SPECIAL COVENANTS OR REMARKS
06-TUL-0-DBA
HSIPL-5143(034)

1. A. The ADMINISTERING AGENCY will advertise, award and administer this project in accordance with the current published Local Assistance Procedures Manual.

B. ADMINISTERING AGENCY agrees that it will only proceed with work authorized for specific phase(s) with an "Authorization to Proceed" and will not proceed with future phase(s) of this project prior to receiving an "Authorization to Proceed" from the STATE for that phase(s) unless no further State or Federal funds are needed for those future phase(s).

C. STATE and ADMINISTERING AGENCY agree that any additional funds which might be made available by future Federal obligations will be encumbered on this PROJECT by use of a STATE-approved "Authorization to Proceed" and Finance Letter. ADMINISTERING AGENCY agrees that Federal funds available for reimbursement will be limited to the amounts obligated by the Federal Highway Administration.

D. Award information shall be submitted by the ADMINISTERING AGENCY to the District Local Assistance Engineer within 60 days of project contract award and prior to the submittal of the ADMINISTERING AGENCY'S first invoice for the construction contract.

Failure to do so will cause a delay in the State processing invoices for the construction phase.

Attention is directed to Section 15.7 "Award Package" of the Local Assistance Procedures Manual.

E. ADMINISTERING AGENCY agrees, as a minimum, to submit invoices at least once every six months commencing after the funds are encumbered for each phase by the execution of this Project Program Supplement Agreement, or by STATE's approval of an applicable Finance Letter. STATE reserves the right to suspend future authorizations/obligations for Federal aid projects, or encumbrances for State funded projects, as well as to suspend invoice payments for any on-going or future project by ADMINISTERING AGENCY if PROJECT costs have not been invoiced by ADMINISTERING AGENCY for a six-month period.

If no costs have been invoiced for a six-month period, ADMINISTERING AGENCY agrees to submit for each phase a written explanation of the absence of PROJECT activity along with target billing date and target billing amount.

ADMINISTERING AGENCY agrees to submit the final report documents that collectively constitute a "Report of Expenditures" within one hundred eighty (180) days of PROJECT completion. Failure of ADMINISTERING AGENCY to submit a "Final Report of Expenditures" within 180 days of PROJECT completion will result in STATE imposing sanctions upon ADMINISTERING AGENCY in accordance with the current Local Assistance Procedures Manual.

Program Supplement 06-5143F15-F022-R1- Page 2 of 7

SPECIAL COVENANTS OR REMARKS
06-TUL-0-DBA
HSIPL-5143(034)
F. Administering Agency shall not discriminate on the basis of race, religion, age, disability, color, national origin, or sex in the award and performance of any Federal-assisted contract or in the administration of its DBE Program Implementation Agreement. The Administering Agency shall take all necessary and reasonable steps under 49 CFR Part 26 to ensure nondiscrimination in the award and administration of Federal-assisted contracts. The Administering Agency's DBE Implementation Agreement is incorporated by reference in this Agreement. Implementation of the DBE Implementation Agreement, including but not limited to timely reporting of DBE commitments and utilization, is a legal obligation and failure to carry out its terms shall be treated as a violation of this Agreement. Upon notification to the Administering Agency of its failure to carry out its DBE Implementation Agreement, the State may impose sanctions as provided for under 49 CFR Part 26 and may, in appropriate cases, refer the matter for enforcement under 18 U.S.C. 1001 and/or the Program Fraud Civil Remedies Act of 1986 (31 U.S.C. 3801 et seq.).

G. Any State and Federal funds that may have been encumbered for this project are available for disbursement for limited periods of time. For each fund encumbrance the limited period is from the start of the fiscal year that the specific fund was appropriated within the State Budget Act to the applicable fund Reversion Date shown on the State approved project finance letter. Per Government Code Section 16304, all project funds not liquidated within these periods will revert unless an executed Cooperative Work Agreement extending these dates is requested by the ADMINISTERING AGENCY and approved by the California Department of Finance.

ADMINISTERING AGENCY should ensure that invoices are submitted to the District Local Assistance Engineer at least 75 days prior to the applicable fund Reversion Date to avoid the lapse of applicable funds. Pursuant to a directive from the State Controller's Office and the Department of Finance; in order for payment to be made, the last date the District Local Assistance Engineer can forward an invoice for payment to the Department's Local Programs Accounting Office for reimbursable work for funds that are going to revert at the end of a particular fiscal year is May 15th of the particular fiscal year. Notwithstanding the unliquidated sums of project specific State and Federal funding remaining and available to fund project work, any invoice for reimbursement involving applicable funds that is not received by the Department's Local Programs Accounting Office at least 45 days prior to the applicable fixed fund Reversion Date will not be paid. These unexpended funds will be irrevocably reverted by the Department's Division of Accounting on the applicable fund Reversion Date.

H. As a condition for receiving federal-aid highway funds for the PROJECT, the Administering Agency certifies that NO members of the elected board, council, or other key decision makers are on the Federal Government Exclusion List. Exclusions can be found at www.sam.gov.

Program Supplement 06-5143F15-F022-R1- Page 3 of 7

SPECIAL COVENANTS OR REMARKS
06-TUL-0-DBA
HSIPL-5143(034)

2. A. ADMINISTERING AGENCY shall conform to all State statutes, regulations and procedures (including those set forth in the Local Assistance Procedures Manual and the Local Assistance Program Guidelines, hereafter collectively referred to as "LOCAL ASSISTANCE PROCEDURES") relating to the federal-aid program, all Title 23 Code of Federal Regulation (CFR) and 2 CFR Part 200 federal requirements, and all applicable federal laws, regulations, and policy and procedural or instructional memoranda, unless otherwise specifically waived as designated in the executed project-specific PROGRAM SUPPLEMENT.

B. Invoices shall be formatted in accordance with LOCAL ASSISTANCE PROCEDURES.

C. ADMINISTERING AGENCY must have at least one copy of supporting backup documentation for costs incurred and claimed for reimbursement by ADMINISTERING AGENCY. ADMINISTERING AGENCY agrees to submit supporting backup documentation with invoices if requested by State. Acceptable backup documentation includes, but is not limited to, agency's progress payment to the contractors, copies of cancelled checks showing amounts made payable to vendors and contractors, and/or a computerized summary of PROJECT costs.

D. Indirect Cost Allocation Plan/Indirect Cost Rate Proposals (ICAP/ICRP), Central Service Cost Allocation Plans and related documentation are to be prepared and provided to STATE (Caltrans Audits & Investigations) for review and approval prior to ADMINISTERING AGENCY seeking reimbursement of indirect costs incurred within each fiscal year being claimed for State and federal reimbursement. ICAPs/ICRPs must be prepared in accordance with the requirements set forth in 2 CFR, Part 200, Chapter 5 of the Local Assistance Procedural Manual, and the ICAP/ICRP approval procedures established by STATE.

E. STATE will withhold the greater of either two (2) percent of the total of all federal funds encumbered for each PROGRAM SUPPLEMENT or $40,000 until ADMINISTERING AGENCY submits the Final Report of Expenditures for each completed PROGRAM SUPPLEMENT PROJECT.

F. Payments to ADMINISTERING AGENCY for PROJECT-related travel and subsistence (per diem) expenses of ADMINISTERING AGENCY forces and its contractors and subcontractors claimed for reimbursement or as local match credit shall not exceed rates authorized to be paid rank and file STATE employees under current State Department of Personnel Administration (DPA) rules. If the rates invoiced by ADMINISTERING AGENCY are in excess of DPA rates, ADMINISTERING AGENCY is responsible for the cost difference, and any overpayments inadvertently paid by STATE shall be reimbursed to STATE by ADMINISTERING AGENCY on demand within thirty (30) days of such invoice.

Program Supplement 06-5143F15-F022-R1- Page 4 of 7

SPECIAL COVENANTS OR REMARKS
06-TUL-0-DBA
HSIPL-5143(034)
G. ADMINISTERING AGENCY agrees to comply with 2 CFR, Part 200, Uniform Administrative Requirements, Cost Principles and Audit Requirement for Federal Awards.

H. ADMINISTERING AGENCY agrees, and will assure that its contractors and subcontractors will be obligated to agree, that Contract Cost Principles and Procedures, 48 CFR, Federal Acquisition Regulations System, Chapter 1, Part 31, et seq., shall be used to determine the allowability of individual PROJECT cost items.

I. Every sub-recipient receiving PROJECT funds under this AGREEMENT shall comply with 2 CFR, Part 200, 23 CFR, 48 CFR Chapter 1, Part 31, Local Assistance Procedures, Public Contract Code (PCC) 10300-10334 (procurement of goods), PCC 10335-10381 (non-A&E services), and other applicable STATE and FEDERAL regulations.

J. Any PROJECT costs for which ADMINISTERING AGENCY has received payment or credit that are determined by subsequent audit to be unallowable under 2 CFR, Part 200, 23 CFR, 48 CFR, Chapter 1, Part 31, and other applicable STATE and FEDERAL regulations, are subject to repayment by ADMINISTERING AGENCY to STATE.

K. STATE reserves the right to conduct technical and financial audits of PROJECT WORK and records and ADMINISTERING AGENCY agrees, and shall require its contractors and subcontractors to agree, to cooperate with STATE by making all appropriate and relevant PROJECT records available for audit and copying as required by the following paragraph:

ADMINISTERING AGENCY, ADMINISTERING AGENCY'S contractors and subcontractors, and STATE shall each maintain and make available for inspection and audit by STATE, the California State Auditor, or any duly authorized representative of STATE or the United States all books, documents, papers, accounting records, and other evidence pertaining to the performance of such contracts, including, but not limited to, the costs of administering those various contracts and ADMINISTERING AGENCY shall furnish copies thereof if requested.

All of the above referenced parties shall make such AGREEMENT, PROGRAM SUPPLEMENT, and contract materials available at their respective offices at all reasonable times during the entire PROJECT period and for three (3) years from the date of submission of the final expenditure report by the STATE to the FHWA.

L. ADMINISTERING AGENCY, its contractors and subcontractors shall establish and maintain a financial management system and records that properly accumulate and segregate reasonable, allowable, and allocable incurred PROJECT costs and matching funds by line item for the PROJECT. The financial management system
Program Supplement 06-5143F15-F022-R1- Page 5 of 7

SPECIAL COVENANTS OR REMARKS
06-TUL-0-DBA
HSIPL-5143(034)
of ADMINISTERING AGENCY, its contractors and all subcontractors shall conform to Generally Accepted Accounting Principles, enable the determination of incurred costs at interim points of completion, and provide support for reimbursement payment vouchers or invoices set to or paid by STATE.

M. ADMINISTERING AGENCY is required to have an audit in accordance with the Single Audit Act of 2 CFR 200 if it expends $750,000 or more in Federal Funds in a single fiscal year of the Catalogue of Federal Domestic Assistance.

N. ADMINISTERING AGENCY agrees to include all PROGRAM SUPPLEMENTS adopting the terms of this AGREEMENT in the schedule of projects to be examined in ADMINISTERING AGENCY's annual audit and in the schedule of projects to be examined under its single audit prepared in accordance with 2 CFR, Part 200.

O. ADMINISTERING AGENCY shall not award a non-A&E contract over $5,000, construction contracts over $10,000, or other contracts over $25,000 [excluding professional service contracts of the type which are required to be procured in accordance with Government Code sections 4525 (d), (e) and (f)] on the basis of a noncompetitive negotiation for work to be performed under this AGREEMENT without the prior written approval of STATE. Contracts awarded by ADMINISTERING AGENCY, if intended as local match credit, must meet the requirements set forth in this AGREEMENT regarding local match funds.

P. Any subcontract entered into by ADMINISTERING AGENCY as a result of this AGREEMENT shall contain provisions B, C, F, H, I, K, and L under Section 2 of this agreement.

3. Appendix E of the Title VI Assurances (US DOT Order 1050.2A) During the performance of this agreement, the ADMINISTERING AGENCY, ADMINISTERING AGENCY'S contractors and subcontractor, (hereinafter referred to as the "contractor") agrees to comply with the following nondiscrimination statutes and authorities; including but not limited to:

Pertinent Nondiscrimination Authorities:

A. Title VI of the Civil Rights Act of 1964 (42 U.S.C. 2000d et seq., 78 stat. 252), (prohibits discrimination on the basis of race, color, national origin); and 49 CFR Part 21.

B. The Uniform Relocation Assistance and Real Property Acquisition Policies Act of 1970, (42 U.S.C. 4601), (prohibits unfair treatment of persons displaced or whose property has been acquired because of Federal or Federal-aid programs and projects); C. Federal-Aid Highway Act of 1973, (23 U.S.C. 324 et seq.), (prohibits discrimination on the basis of sex);
D. Section 504 of the Rehabilitation Act of 1973, (29 U.S.C. 794 et seq.), as Program Supplement 06-5143F15-F022-R1- Page 6 of 7

SPECIAL COVENANTS OR REMARKS
06-TUL-0-DBA
HSIPL-5143(034)
amended, (prohibits discrimination on the basis of disability); and 49 CFR Part 27; E. The Age Discrimination Act of 1975, as amended, (42 U.S.C. 6101 et seq.), (prohibits discrimination on the basis of age);
F. Airport and Airway Improvement Act of 1982, (49 U.S.C. 4 71, Section 4 7123), as amended, (prohibits discrimination based on race, creed, color, national origin, or sex); G. The Civil Rights Restoration Act of 1987, (PL 100-209), (Broadened the scope, coverage and applicability of Title VI of the Civil Rights Act of 1964, The Age Discrimination Act of 1975 and Section 504 of the Rehabilitation Act of 1973, by expanding the definition of the terms "programs or
activities" to include all of the programs or activities of the Federal-aid recipients, subrecipients and contractors, whether such programs or activities are Federally funded or not);
H. Titles II and III of the Americans with Disabilities Act, which prohibit discrimination on the basis of disability in the operation of public entities, public and private transportation systems, places of public accommodation, and certain testing entities (42 U.S.C. 12131-12189) as implemented by Department of Transportation regulations at 49 C.F.R. parts 37 and 38; I. The Federal Aviation Administration's Nondiscrimination statute (49 U.S.C. 47123) (prohibits discrimination on the basis of race, color, national origin, and sex); J. Executive Order 12898, Federal Actions to Address Environmental Justice in Minority Populations and Low-Income Populations, which ensures nondiscrimination against minority populations by discouraging programs, policies, and activities with disproportionately high and adverse human health or environmental effects on minority and low-income populations; K. Executive Order 13166, Improving Access to Services for Persons with Limited English Proficiency, and resulting agency guidance, national origin discrimination includes discrimination because of limited English proficiency (LEP). To ensure compliance with Title VI, you must take reasonable steps to ensure that LEP persons have meaningful access to your programs (70 Fed. Reg. at 74087 to 74100);
L. Title IX of the Education Amendments of 1972, as amended, which prohibits you from discriminating because of sex in education programs or activities (20 U.S.C. 1681 et seq).

Program Supplement 06-5143F15-F022-R1- Page 7 of 7
City Council Staff Report
Department: FIRE SERVICES March 28, 2023
To: Mayor and City Council
From: Jordan Webster, Fire Chief
Subject:

Resolution No. 2023-19 Approving a Budget Amendment in the amount of $1,436,020.29 and Authorization to Purchase a New Fire Ladder Truck (JORW)

RECOMMENDATION
Council to taking the following actions by one motion and one vote:

1. Approve Budget Amendment No. 2023-15 budgeting $1,436,020.29 in the FY 2022-23 budget for the acquisition of a new fire ladder truck; and,

2. Authorize staff to order the new fire ladder truck through the Houston-Galveston Area Council (HGACBuy) Purchasing Cooperative; and,

3. Authorize staff to execute any related documents and agreements associated with the purchase of the new fire ladder truck.

EXECUTIVE SUMMARY
The Fire Master Plan identified the need to replace the existing 2004 fire ladder truck in 2024. The fire ladder truck is 20 years old and is at the end of its useful life as a frontline fire vehicle. The city was able to secure a $2.0 million state earmark through Senator Hurtado's office in 2022 for the purchase a new fire ladder truck and associated firefighting equipment. The city has received the funds from the state Office of Emergency Services and is requesting that the City Council approve a budget amendment to include the funds in the current Fiscal Year 2022-23 budget.

OUTSTANDING ISSUES
None.

DISCUSSION
The California Budget Act of 2022 included state appropriations to support State Government for fiscal year 2022/2023. On September 1, 2022, Assembly Bill 179 was passed. In the 2022 State Budget, Senator Hurtado secured $465.75 million dollars to support investments in public safety, water, education and food programs.

The Central Valley received a record $56 million for public safety, the largest amount ever secured for much needed updates to fire personnel safety equipment, new fire and police stations across the district.

One of the State earmarks that Senator Hurtado was able to secure was $2.0 million to the City of Dinuba for the purchase of a new 105' Quint (Ladder Truck) and firefighting equipment for the Dinuba Fire Department. This new fire apparatus will replace the department's current 105' Quint that is nearly 20 years old. Having modern and reliable equipment is critical to the safety of our citizens and the safety of our firefighters.

The Houston-Galveston Area Council (HGACBuy) Purchasing Cooperative allows agencies to make the procurement process more efficient by establishing competitively priced contracts for goods and services. All contracts available through HGACBuy have been awarded through a public competitive procurement process that is compliant with State and local guidelines.

Staff is recommending the purchase of a Spartan/Smeal 105' Quint. This fire apparatus meets the requirements needed to maintain our current ISO rating and is similar in specifications to our current fleet. Maintaining consistency in the fleet will allow for efficiency in the operations of our personnel, which is critical during times of emergency. Specifications of the recommended Smeal 105' Quint can be found in Attachment "B". Due to the prolonged build time and benefit of pre-payment, tools and equipment needed to outfit the new 105' Quint will be included in future budget process.

Staff is recommending that the City Council adopt Resolution No. 2023-15 approving a budget amendment in the amount of $1,436,020.29 as part of the Fiscal Year 2022- 23 budget in order to purchase the new fire ladder truck. A copy of the resolution is enclosed herein as Attachment 'A'.

FISCAL IMPACT
The cost for the new 105' Quint is $1,436,020.29. This cost is comprised of $1,363,537.00 for the 105' Quint, 100% prepayment discount of $45,237.00, a performance bond of $5,221.00 and $112,499.29 for sales tax. The cost for the 105' Quint will be funded directly from a California Office of Emergency Services Passthrough Grant.

PUBLIC HEARING
None.

ATTACHMENTS:

Description
Attachment "A" Resolution 2023-19 for 2022-23 Budget Amendment Exhibit 1, Budget Amendment 2023-15
Attachment "B" Smeal 105' Quint Specifications
RESOLUTION 2023-19

A RESOLUTION OF THE COUNCIL OF THE CITY OF DINUBA

APPROVING AND ADOPTING THE BUDGET AMENDMENT OUTRIGHT PURCHASE OF A NEW FIRE LADDER TRUCK.

WHEREAS, the FY 2022/2023 Annual Budget reflects the City of Dinuba’s ongoing commitment to providing core services to the community, consistent with the strategic goals established by the City Council; and
WHEREAS, the FY 2022/23 Annual Budget was approved by the City Council on June 28, 2022 by Resolution 2022-44, and any subsequent amendments must be approved by Resolution; and
WHEREAS, a budget amendment is necessary to allow for the outright purchase of a new fire ladder truck, which was not included in the 2022/23 fiscal year; NOW, THEREFORE, BE IT RESOLVED, the Dinuba City Council hereby resolves that the FY 2022/2023 Annual Budget be amended to provide for the full purchase price of a new ladder truck.

PASSED, APPROVED AND ADOPTED this 28th day of March 2023, at a regular meeting of the Dinuba City Council by the following vote:

AYES:

NOES:

ABSTAIN:

ABSENT:

BY: ATTEST:
_______________________ __________________________
Mayor of the City of Dinuba City Clerk

REQUEST FOR BUDGET AMENDMENT
Requested by: Jordan Webster
Account Budget Amounts
Numbers Increase Decrease

REVENUES
322 State Fire Suppression Reimbursement Fund Balance 1,436,020.29

APPROPRIATIONS
322.60.601-730.1050 Capital Outlay – Trucks and Other Heavy Vehicles 1,436,020 Reason(s) for Budget Amendment:

Department Director
Signature Date
Approval Required Budget Amendment:

Administrative Services Director
Signature Date
City Manager
Signature Date
City Council: Approved Resolution #__________ Denied
Date
BA No.____________ JE No. _______________ Date Posted ___________ By: ____________________________ *note please have reviewed and presigned prior to council meeting to give to City Clerk Form only for items that are amending the 2020/21 adopted budget.

Fund Name Description
To purchase the 105’ Quint (Fire Ladder Truck) outright at a total cost including tax of $1,436,020.29. Purchasing the fire apparatus outright triggers a cost savings of $45,237.00.

Dinuba Fire Department
Spartan/Smeal 105' Quint
6FRWW%HFN
)LUH$SSDUDWXV6ROXWLRQV
6DOHV0DQDJHU

6FRWWIDVILUH#JPDLOFRP
• Office: (909) 421-2728 • Fax: (909) 421-4150 • https://www.facebook.com/ Fire Apparatus Solutions • Website: FASService.Org
PH: (402)719-1242 Email: [email protected] Address: 66\FDPRUH$YH5LDOWR&$ Gladiator
Fire Apparatus Solutions
2763 S. Vista AVE
Bloomington, CA 92316
Prepared By : TRISH HANSEN
[email protected]
Prepared For :

DINUBA FIRE DEPARTMENT
Monday, September 19, 2022 11:19:22 AM CDT
Table of Contents
Quotation3
Front Lightbar Layout 15
5450M-002 Cab Front Lightbar Layout 15
Panel Layout 17
5020-002 Panel Layout 18
Specification 20
Quotation
Description Qty.

VEHICLE
S 0100-012 MODEL Gladiator 1
O 8012-002 CUSTOMERS / OEMS Smeal (02070)[1002812] 1
S 8011-024 MODEL YEAR Model Year - 2024 1
S 8001-001 COUNTRY OF SERVICE Country of Service United States Of America 1 S 8017-009 CAB AND CHASSIS LABELING

LANGUAGE
Cab and Chassis Labeling Language English w/Innovative
Controls Labels
1 O 8006-011 APPARATUS TYPE Apparatus Type Rear Mount Quint 1 O 8066-018 REAR MOUNT AERIAL DEVICE Rear Mount Aerial Device Smeal S53RL-105 / 105 RearMount Ladder
1 S 8008-001 VEHICLE TYPE Vehicle Type Straight Truck 1 S 8008A000

VEHICLE ANGLE OF APPROACH

PACKAGE
Vehicle Angle of Approach NFPA Minimum 8.00 Degrees 1
O 0104-003 AXLE CONFIGURATION Axle Configuration 6x4 (Rear Tandem Axle Drive Only) 1 O 0101-016 GROSS AXLE WEIGHT RATINGS
FRONT
GAWR Front 23000# 1
O 0102-010 GROSS AXLE WEIGHT RATINGS
REAR
GAWR Rear 52000# 1
S 8010-201 PUMP PROVISION Pump Provision Driveline Midship, Pump Mode Prog w/Auto Park Brake "N"
1 O 8009-004 WATER & FOAM TANK CAPACITY Water & Foam Tank Capacity Up to 750 Gallons 1 CAB
S 1000-004 CAB STYLE Cab Style MFD 10" Raised Roof 1
S 1501-002 CAB FRONT FASCIA Cab Frt Fascia Classic 1
S 1518-025 FRONT GRILLE Cab Frt Grille Hinged Classic Styled 1 S 1551-002 CAB UNDERCOAT Cab Undercoat 1
S 1552-002 CAB SIDE DRIP RAIL Cab Side Drip Rail 1
S 1521-001 CAB PAINT EXTERIOR Cab Paint Exterior Single Color 1 S 1533-002 CAB PAINT MANUFACTURER Cab Paint Manufacturer Sikkens 1 S 1522-001 CAB PAINT PRIMARY/LOWER COLOR Cab Paint Primary/Lower Color No Selection/TBD 1 S 8013-056 CAB PAINT WARRANTY Cab Paint Warranty (10) Year RFW0710 1 S 1334-036 CAB PAINT INTERIOR Cab Paint Int Multi-tone Silver Gray 1 S 1005-001 CAB ENTRY DOORS Cab Entry Doors (4) 1
O 1101-102 CAB ENTRY DOOR TYPE Cab Entry Door Type Barrier Free w/Pollak Switches 1 S 1322-007 CAB INSULATION Cab Insulation Nonwoven Polyester Fiber 1 O 1556-009 LH MID EMS COMPARTMENT LH Mid EMS Compartment 26"H w/Offset to 24"W Chamfered Corner
1 O 1558-007 LH MID EMS COMPARTMENT

EXTERIOR ACCESS
LH Mid EMS Cmpt Ext Access 26"H Hng Dr 1
O 1560-002 LH MID EMS COMPARTMENT

INTERIOR
LH Mid EMS Cmpt Interior Solid Wall No Access 1
O 1566-002 LH MID EMS COMPARTMENT DOOR LH Mid EMS Cmpt Door Hardware D-Ring Latch 1

HARDWARE
O 1557-008 RH MID EMS COMPARTMENT RH Mid EMS Compartment 26"H w/Offset to 24"W Chamfered Corner
1 O 1559-007 RH MID EMS COMPARTMENT

EXTERIOR ACCESS
RH Mid EMS Cmpt Ext Access 26"H Hng Dr 1
O 1561-002 RH MID EMS COMPARTMENT

INTERIOR
RH Mid EMS Cmpt Interior Solid Wall No Access 1
O 1567-002 RH MID EMS COMPARTMENT DOOR

HARDWARE
RH Mid EMS Cmpt Door Hardware D-Ring Latch 1
O 5384-002 MID EMS COMPARTMENT LIGHTING Mid EMS Compartment Lighting LED 2 O 1535-016 MID EMS COMPARTMENT EXTERIOR
FINISH
Mid EMS Cmpt Ext Finish Multi-tone Silver Gray 1
O 1536-018 MID EMS COMPARTMENT INTERIOR
FINISH
Mid EMS Cmpt Interior Finish Multi-tone Silver Gray 1
O 1002-011 CAB ROOF TRENCH Cab Roof Trench 50"W x 13"D 1 S 8004-033 CAB STRUCTURAL WARRANTY Cab Structural Warranty (10) Year RFW0602 1 S 9001-006 CAB TEST INFORMATION Cab Test Information Crash Test ECE-R29/SAE J2420/SAE J2422
1 ELECTRICAL POWER DISTRIBUTION
S 5000-018 ELECTRICAL SYSTEM Elec System 12V DC Multiplex 1 O 5008-072 OEM WIRING OEM Wir Smeal ECM Park Brake Input 1 O 5006-002 APPARATUS WIRING PROVISION Apparatus Wiring Provision (8) Circuit Panel 1 S 5005-200 MULTIPLEX DISPLAY MUX Display Weldon Vista LH Sw Pnl 1 S 5004-002 LOAD MANAGEMENT SYSTEM Load Management System Multiplex 1 S 5622-003 DATA RECORDING SYSTEM Data Recording Sys Vehicle Data Weldon MUX 1 O 5031-013 ACCESSORY POWER Accessory Pwr & Gnd Stud 40A Batt & 15A Ign w/350A Mstr Sw/300A Batt OEM Conn
1 O 5030-037 AUXILIARY ACCESSORY POWER Aux Acc Pwr 10 Fuse Pnl Bhd Off Seat w/40A Fuse Batt Dir 5' Loop
1 S 5011-001 EXTERIOR ELECTRICAL TERMINAL

COATING
Exterior Electrical Terminal Coating Spray On Plasti Dip 1 S 8014-002 ELECTRICAL SYSTEM WARRANTY Electrical System Warranty (2) Year RFW0202 1 ENGINE
O 1701-172 ENGINE Engine Diesel 605HP Cummins X15 - EPA 2021 1 S 1329-002 CAB ENGINE TUNNEL Cab Engine Tunnel Large 1
S 1731-002 DIESEL PARTICULATE FILTER

CONTROLS
DPF Ctrl Regeneration Sw & Inhibit Sw 1
S 1718-002 ENGINE PROGRAMMING HIGH IDLE
SPEED
Engine Programming High Idle Speed 1250 RPM 1
S 1719-005 ENGINE HIGH IDLE CONTROL Engine High Idle Ctrl Manual and Automatic w/MUX 1 S 1710-001 ENGINE PROGRAMMING ROAD

SPEED GOVERNOR
Engine Programming Road Speed Governor Enabled 1
S 1713-010 AUXILIARY ENGINE BRAKE Aux Engine Brake Compression Brake w/VG Turbo 1 O 1708-007 AUXILIARY ENGINE BRAKE

CONTROL
Aux Engine Brake Ctrl Off/Low/High MUX 1
S 1720-003 ELECTRONIC ENGINE OIL LEVEL

INDICATOR
Elec Engine Oil Level Indicator 1
O 1715-004 FLUID FILLS Fluid Fills Fwd For Large Displacement Cap 1 S 1735-001 ENGINE DRAIN PLUG Engine Drain Plug 1
S 8002-001 ENGINE WARRANTY Engine Warranty Cummins (5) Year/100,000 Miles 1 S 1707-116 REMOTE THROTTLE HARNESS Rmt Throttle Harness Cab Harness Only Shift Interlock 1 S 1721-001 ENGINE PROGRAMMING REMOTE

THROTTLE
Engine Program Rmt Throttle Off 1
S 1727-001 ENGINE PROGRAMMING IDLE SPEED Engine Programming Idle Speed 700 RPM 1

AIR INTAKE
S 2801-010 ENGINE AIR INTAKE Engine Air Intake Filtration and Restriction w/Replaceable Element Abv Radiator
1 COOLING
S 2704-016 ENGINE FAN DRIVE Engine Fan Drive Variable Speed 1 S 2701-021 ENGINE COOLING SYSTEM Engine Cooling System Serial Flow w/Package Drop-Out Prov 1 S 2711-005 ENGINE COOLING SYSTEM

PROTECTION
Engine Cooling System Protection Light Duty Skid Plate Paint Frame Color
1 S 2708-001 ENGINE COOLANT Engine Coolant Extended Life 1 O 2707-002 ENGINE COOLANT FILTER Engine Coolant Filter 1 S 2706-003 ELECTRONIC COOLANT LEVEL

INDICATOR
Elec Low Coolant Level Indicator 1
S 2705-002 ENGINE PUMP HEAT EXCHANGER Engine Pump Heat Exchanger 1 S 2709-001 COOLANT HOSES Coolant Hoses Silicone 1
S 2710-005 ENGINE COOLANT OVERFLOW
BOTTLE
Engine Coolant Overflow Expansion Bottle 1

EXHAUST
O 2901-074 ENGINE EXHAUST SYSTEM Eng Exhaust Sys Under Frm RH Single Module Aftertreatment Inboard Inner Frm Mnt
1 S 2907-003 DIESEL EXHAUST FLUID TANK Diesel Exhaust Fluid Tank LH 6 Gal Fill Thru Rr Step 1 S 2902-010 ENGINE EXHAUST ACCESSORIES Engine Exhaust Acc Temp Mitigation 1 S 2906-002 ENGINE EXHAUST WRAP Engine Exhaust Wrap 1
S 8018-002 EMISSIONS SYSTEM WARRANTY Emissions System Warranty (5) Year/100,000 Miles RFW0140 1

TRANSMISSION
O 1801-018 TRANSMISSION Transmission Allison 4000 EVS w/Retarder 1 S 1806-001 TRANSMISSION MODE

PROGRAMMING
Transmission Mode Programming 4th Startup/5th Mode 1
S 1811-004 TRANSMISSION FEATURE

PROGRAMMING
Transmission Feature Programming Allison Gen 5 & 6-E I/O Package 198/Pumper
1 S 1807-005 TRANSMISSION SHIFT SELECTOR Transmission GEN 5 & 6-E Shift Sel Key Pad/Push Button 1 S 1815-002 ELECTRONIC TRANSMISSION OIL

LEVEL INDICATOR
Elec Transmission Oil Level Indicator 1
O 1812-004 TRANSMISSION RETARDER

CONTROL
Trans Ret Ctrl 1/3 Throttle 2/3 Brk On/Off MUX 1
O 1816-004 TRANSMISSION RETARDER

CAPACITY LEVEL
Transmission Retarder Capacity Level High 1
S 1814-002 TRANSMISSION PRE-SELECT WITH

AUXILIARY BRAKE
2nd Gear Pre-Select 1
S 1808-007 TRANSMISSION COOLING SYSTEM Transmission Cooling System 1 S 1817-001 TRANSMISSION DRAIN PLUG Transmission Drain Plug 1 S 8005-001 TRANSMISSION WARRANTY Transmission Warranty Allison (5) Year 1

POWER TAKE OFF
O 2004-004 LH PTO LH PTO Cust Installed 1
O 2001-109 LH PTO MODEL LH PTO Model Chelsea 280-GGFJP-B5XD 1 O 2005-008 PTO LOCATION PTO Location 8:00/1:00 1
O 2015-030 LH PTO CONTROL LH PTO Ctrl Rkr Enable "Aerial Master"/Rkr Actv "Aerial PTO"
1 DRIVELINE
O 3001-017 DRIVELINE Driveline MSI 1810/1710 w/Meritor U-Joints w/Thrust Washers
1 O 3005-074 MIDSHIP PUMP / GEARBOX Midship Pump Jackshaft w/Smeal Aerial Pump Mount Holes 1 S 3008-085 MIDSHIP PUMP / GEARBOX MODEL Midship Pump/Gearbox Model Waterous CSUC20 Fwd 1 O 3048-006 MIDSHIP PUMP GEARBOX DROP Midship Driveline Pump Gearbox Drop Waterous "B" 1 S 3009-007 MIDSHIP PUMP RATIO Midship Pump Ratio 2.27:1 1 O 3010-
1140

MIDSHIP PUMP LOCATION C/L

SUCTION TO C/L REAR AXLE
Midship Pump Location C/L Suction to C/L Rear Axle 114.0" 1 O 5013-005 PUMP SHIFT CONTROLS Pump Shift Ctrl Elec Over Air in Knee Area Pmp Act Up 1 O 3049-003 PUMP SHIFT CONTROL PLUMBING Pump Shift Control Plumbing Pre-Plumb Elec/Air 1

FUEL SYSTEMS
O 3109-064 FUEL FILTER/WATER SEPARATOR Fuel Filter/Wtr Separator Racor GreenMAX 6600R w/Lt & Alarm
1 O 3111-002 FUEL LINES Fuel Lines Wire Braid 1
S 3103-008 ELECTRIC FUEL PRIMER Electric Fuel Primer Engine Sply Electric Lift Pump 1 O 3112-013 FUEL COOLER Fuel Cooler Behind Rear Axle Raised 1 O 3101-102 FUEL TANK Fuel Tank 68 Gallon 1
S 3130-001 FUEL TANK MATERIAL AND FINISH Fuel Tank Material Steel & Finish Painted Frame Components Color
1 S 3131-001 FUEL TANK STRAP MATERIAL AND
FINISH
Fuel Tank Strap Material Steel & Finish Painted Frame
Components Color
1 O 3132-011 FUEL TANK MISCELLANEOUS

OPTIONS
Fuel Tank Miscellaneous Options - Temporarily Mounted 1 O 3102-016 FUEL TANK FILL PORT Fuel Tank Fill Port LH Mid/RH Mid/LH Fwd 1 O 3114-006 FUEL TANK SERVICEABILITY

PROVISIONS
Fuel Tank Serviceability Prov 12' Fuel Line Extension 1 S 3115-002 FUEL TANK DRAIN PLUG Fuel Tank Drain Plug Magnetic 1

FRONT AXLE
O 2401-022 FRONT AXLE Frt Axle Meritor MFS 23000# Beam 1 S 8059-022 FRONT AXLE WARRANTY Front Axle Warranty Meritor 2024 1 S 2405-001 FRONT WHEEL BEARING Frt Wheel Bearing Lube Oil 1

LUBRICATION

FRONT SUSPENSION
S 2502-002 FRONT SHOCK ABSORBERS Frt Shock Absorbers Bilstein 1 O 2501-018 FRONT SUSPENSION Frt Suspension 11 Leaf 23000# 1

STEERING
S 2601-006 STEERING COLUMN/WHEEL Steering Column/Wheel Tilt/Telescopic 18" 4 Spoke 1 S 2609-002 ELECTRONIC POWER STEERING

FLUID LEVEL INDICATOR
Elec Power Steering Fluid Level Indicator 1
S 2603-011 POWER STEERING PUMP Power Steering Pump TRW w/Passive Cooler 1 S 2606-009 FRONT AXLE CRAMP ANGLE Front Axle Cramp Angle 48L/44R Degrees 1 S 2610-005 POWER STEERING GEAR Power Steering Gear TRW TAS 85 w/Assist 1 S 2608-001 CHASSIS ALIGNMENT Chassis Alignment 1

REAR AXLE
O 3401-012 REAR AXLE Rear Axle 54000# Meritor RT-52-185 1 S 3403-001 REAR AXLE DIFFERENTIAL

LUBRICATION
Rear Axle Differential Lubrication Oil 1
S 8061-019 REAR AXLE WARRANTY Rear Axle Warranty Meritor 2024 1 S 3411-001 REAR WHEEL BEARING

LUBRICATION
Rear Wheel Bearing Lubrication Oil 1
O 3407-003 REAR AXLE DIFFERENTIAL

CONTROL
Rear Axle Differential Ctrl Interaxle Lock 1
O 3408-003 VEHICLE TOP SPEED Vehicle Top Speed 60 MPH 1 S 3410-001 REAR AXLE EXTERNAL VENT Rear Axle External Vent OEM Housing Breather 1

REAR SUSPENSION
O 3501-035 REAR SUSPENSION Rear Susp Hendrickson FireMaax Air 48001-54000# 1 O 3503-003 REAR SHOCK ABSORBERS Rear Shock Absorbers Suspension Sply 1 TIRES
S 3625-002 TIRE INTERMITTENT SERVICE
RATING
Tire Intermittent Service Ratings Acceptable 1
O 3601-063 FRONT TIRE Frt Tire 425/65R 22.5 Michelin XZY3 2 O 3602-010 REAR TIRE Rear Tire 12R 22.5 Michelin XZE 8
O 3413-538 REAR AXLE RATIO Rear Axle Ratio 5.38 1
S 3614-030 TIRE PRESSURE INDICATOR Tire Pressure Ind Frt & Rr LED 1 WHEELS
O 3701-034 FRONT WHEEL Frt Wheel Alcoa Dura-Bright 22.5 x 12.25 Alum 2 O 3703-062 REAR WHEEL Rr Whl Alcoa Dura-Bright 22.5 x 8.25 Alum 8 O 3702-018 WHEEL TRIM Wheel Trim Hub & Nut Covers SS Shiploose (2) Sets 1 BRAKES
O 3205-015 BRAKE SYSTEM Brake System ABS/ATC/ESC Tandem Axle MUX Btn 1 S 3206-003 FRONT BRAKES Frt Brakes Meritor EX225 Disc 17" 1 S 3207-005 REAR BRAKES Rr Brakes S-Cam Drum 16.5" x 7" Cast Iron Shoe 1 S 3208-001 PARK BRAKE Prk Brake Rr Wheels Only 1
O 3219-002 SUPPLEMENTAL BRAKE Supplemental Brake Frt Service Brakes Prk Brk Actv 1 S 3204-029 PARK BRAKE CONTROL Prk Brake Ctrl LH Tunnel Mnt, Integrated w/Shift Pod, Adjacent To Trans Shifter
1 O 3214-002 REAR BRAKE SLACK ADJUSTERS Rr Brake Slack Adjusters Haldex 1 S 3202-001 AIR DRYER Air Dryer Wabco System Saver 1200 Bhd RH Step 1 S 3215-004 FRONT BRAKE CHAMBERS Frt Brake Chambers MGM Type 24 Long Stroke 1 S 3210-015 REAR BRAKE CHAMBERS Rr Brake Chambers TSE 30/36 Long Stroke 1

AIR SUPPLY SYSTEMS
S 3320-001 AIR COMPRESSOR Air Compressor Wabco SS318 18.7 CFM 1 S 3339-004 AIR GOVERNOR Air Governor Mnt on Air Dryer Bracket 1 O 3303-002 MOISTURE EJECTORS Moisture Ejectors w/Cable 1 O 3307-001 AIR SUPPLY LINES Air Sply Lines Nylon w/Compression Fittings 1 S 3338-002 REAR AIR TANK MOUNTING Rear Air Tank Mnt Any Bhd Rear Axle Perpendicular w/Frame
1 FRAME
O 2103-
2280
WHEELBASE Wheelbase 228.0" 1
O 2106-
0640
REAR OVERHANG Rear Overhang 64.0" 1
S 2101-002 FRAME Frame Double Channel 35.00" Width 1
O 2111-136 MISC FRAME OPTIONS Misc Frame Options Smeal Aerials 105RM, 100RM, 125RM, 100MM Layout 4
1 O 2117-004 FRAME CLEAR AREA Frame Clear Area Inside/Outside Rail 30" Rwd Back of Cab 1 O 2110-101 FRAME PAINT Frame Paint Powder Coat Black 1
S 8007-036 FRAME ASSEMBLY STRUCTURAL

WARRANTY
Frame Assembly Structural Warranty (50) Year RFW0305 1
O 8019-002 FRAME RAIL CORROSION

WARRANTY
Frame Rail Corrosion Warranty (3) Year RFW0311 1
S 8022-004 FRAME COMPONENTS CORROSION

WARRANTY
Frame Components Corrosion Warranty (3) Year RFW0315 1
BUMPER
O 2201-006 FRONT BUMPER Frt Bumper Formed Steel Special Approach Style 1 O 2202-024 FRONT BUMPER EXTENSION
LENGTH
Frt Bumper Extension Length 12.5" Special Approach Height 1 O 2206-001 FRONT BUMPER PAINT Frt Bumper Paint Primary/Lower Cab Color 1 O 2208-003 FRONT BUMPER APRON Frt Bumper Apron For 12.5" Extension 1 O 2237-004 FRONT BUMPER DISCHARGE Front Bumper Discharge 2.0" LH Frame Mnt Plumbing 1 O 2211-012 FRONT BUMPER COMPARTMENT
CENTER
Frt Bumper Cmpt Ctr For Approach Style Bumper 1
O 5503-021 MECHANICAL SIREN Mechanical Siren Federal Signal Q2B Recess Mnt 1 O 2218-049 MECHANICAL SIREN LOCATION Mech Siren Location Frt Bmpr Face LH Extreme OB 1 S 5501-020 AIR HORN Air Horn (2) 21" Round Hadley E-Tone 1 O 2216-007 AIR HORN LOCATION Air Horn Location (2) Frt Bmpr Face RH 1 S 2232-002 AIR HORN RESERVOIR Air Horn Reservoir (1) 1200 Cu In 1 O 5504-060 ELECTRONIC SIREN SPEAKER Elect Siren Speaker 100W Federal Signal Dynamax w/EF Grille
1 O 2217-003 ELECTRONIC SIREN SPEAKER

LOCATION
Elec Siren Speaker Location Frt Bmpr Face LH IB 1
O 2204-006 FRONT BUMPER TOW EYES Frt Bumper Tow Eyes 2" Chrome Through 1

CAB TILT
S 2301-001 CAB TILT SYSTEM Cab Tilt System 1
O 2302-005 CAB TILT AUXILIARY PUMP Cab Tilt Aux Pump Manual Mnt w/Tilt Pump 1 O 2303-003 CAB TILT LIMIT SWITCH Cab Tilt Limit Sw Preset Limit 1 S 2305-001 CAB TILT CONTROL RECEPTACLE Cab Tilt Ctrl Receptacle Temp 1 S 2306-002 CAB TILT LOCK DOWN INDICATOR Cab Tilt Lock Down Indicator 1

CAB GLASS
S 1401-009 CAB WINDSHIELD Cab Windshield 1
S 1402-005 GLASS FRONT DOOR Glass Frt Dr Roll Down/XDuty Regulator 1 S 1407-001 GLASS TINT FRONT DOOR Glass Tint Frt Dr Automotive Green 1 S 1419-012 GLASS REAR DOOR RIGHT HAND Glass Rr Dr RH Roll Down/XDuty Regulator 1 S 1430-001 GLASS TINT REAR DOOR RIGHT
HAND
Glass Tint Rr Door RH Automotive Green 1
S 1412-013 GLASS REAR DOOR LEFT HAND Glass Rr Dr LH Roll Down/XDuty Regulator 1 S 1431-001 GLASS TINT REAR DOOR LEFT HAND Glass Tint Rr Door LH Automotive Green 1 O 1410-010 GLASS SIDE MID RIGHT HAND Glass Side Mid RH Fxd 16"W x 12"H 1 S 1432-001 GLASS TINT SIDE MID RIGHT HAND Glass Tint Side Mid RH Automotive Green 1 O 1409-010 GLASS SIDE MID LEFT HAND Glass Side Mid LH Fxd 16"W x 12"H 1 S 1433-001 GLASS TINT SIDE MID LEFT HAND Glass Tint Side Mid LH Automotive Green 1

CLIMATE CONTROL
O 1614-115 CLIMATE CONTROL Climate Ctrl Htr Defroster Frt Under Dash/Htr A/C Tunnel Mnt
1 S 1632-002 CLIMATE CONTROL DRAIN Climate Control Drain Gravity 1 O 1617-113 CLIMATE CONTROL ACTIVATION Climate Ctrl Actv Rotary Dash Mnt Ctr Under Dash Defroster/Device Mnt Tunnel A/C
1 O 1603-002 A/C CONDENSER LOCATION A/C Condenser Location Roof Mnt Mid LH 1 O 1601-001 A/C COMPRESSOR A/C Compressor Large Capacity 1 O 1530-103 UNDER CAB INSULATION Under Cab Insulation Eng Tnl w/Removable Alum Overlay 1

CAB INTERIOR
S 1327-001 INTERIOR TRIM FLOOR Interior Trim Floor 1
S 1302-001 INTERIOR TRIM Interior Trim Vinyl 1
S 1368-002 REAR WALL INTERIOR TRIM Rear Wall Interior Trim Vinyl 1 S 1306-006 HEADER TRIM Header Trim XDuty 1
O 1305-020 TRIM CENTER DASH Trim Center Dash XDuty w/Under Dash Htr Defroster Provision
1 O 1339-104 TRIM LEFT HAND DASH Trim LH Dash XDuty w/Htr Defroster Provision 1 O 1321-021 TRIM RIGHT HAND DASH Trim RH Dash XDuty MDT Prov w/Htr Defroster Provision 1 S 1307-002 ENGINE TUNNEL TRIM Eng Tnl Trim Flr Mat 1
O 5040-116 POWER POINT DASH MOUNT Pwr Pnt Dash Mnt Batt Dir (4) Sw Pnl/(2) 2.4A USB Sw Pnl 1 S 1303-038 STEP TRIM Step Trim Embossed & Diamond Cut Lwr Flex-Tred Mid 1 S 1379-003 UNDER CAB ACCESS DOOR Under Cab Access Door Rear Step LH Painted 1 S 1102-013 INTERIOR DOOR TRIM Interior Door Trim Painted 1 S 1323-001 DOOR TRIM CUSTOMER

NAMEPLATE
Door Trim Customer Nameplate 1
S 1105-001 CAB DOOR TRIM REFLECTIVE Cab Dr Trim Reflective Vert Stripe/6" Chevron w/Logo 1 S 1308-001 INTERIOR GRAB HANDLE "A"
PILLAR
Interior Grab Handle 'A' Pillar 11" Molded 1
S 1332-008 INTERIOR GRAB HANDLE FRONT
DOOR
Interior Grab Handle Frt Door Horiz 9" 1
S 1345-002 INTERIOR GRAB HANDLE REAR
DOOR
Int Grab Handle Rr Dr Alum Window Span 30" Black
Powder Coat
1 S 1301-003 INTERIOR SOFT TRIM COLOR Interior Soft Trim Color Gray 1 O 1337-002 INTERIOR TRIM SUNVISOR Interior Trim Sunvisor Tinted 1 S 1304-001 INTERIOR FLOOR MAT COLOR Interior Floor Mat Color Gray 1 S 1335-017 CAB PAINT INTERIOR DOOR TRIM Cab Paint Int Dr Trim Multi-tone Silver Gray 1 S 1371-017 HEADER TRIM INTERIOR PAINT Header Trim Interior Paint Multi-tone Silver Gray 1 S 1370-019 TRIM CENTER DASH INTERIOR
PAINT
Trim Center Dash Interior Paint Multi-tone Silver Gray 1 S 1378-018 TRIM LEFT HAND DASH INTERIOR
PAINT
Trim LH Dash Interior Paint Multi-tone Silver Gray 1
S 1373-018 TRIM RIGHT HAND DASH INTERIOR
PAINT
Trim RH Dash Interior Paint Multi-tone Silver Gray 1
S 1344-002 DASH PANEL GROUP Dash Pnl Group 3-Pnl 1
O 1312-074 SWITCHES CENTER PANEL Switches Ctr Pnl 8 Upr LH 1 O 1313-007 SWITCHES LEFT PANEL Switches Left Pnl 5 (3+2) w/Headlight/Dimmer/Wiper 1 S 1314-001 SWITCHES RIGHT PANEL Switches Right Pnl 0 1

CAB SEATS
S 1225-007 SEAT BELT WARNING Seat Belt Warn Vista Display w/VDR 1 O 1237-004 SEAT MATERIAL Seat Material Turnout Tuff 1
S 1243-001 SEAT COLOR Seat Color Gray/Red Seat Belts 1
S 1249-001 SEAT BACK LOGO Seat Back Logo Spartan 4
O 1201-021 SEAT DRIVER Seat Driver Seats Inc Battalion 10-Way Elect ABTS 1 S 1213-025 SEAT BACK DRIVER Seat Back Driver Non-SCBA ABTS 1 S 1219-001 SEAT MOUNTING DRIVER Seat Mounting Driver 1
O 1202-020 SEAT OFFICER Seat Officer Seats Inc Battalion 6-Way Elect ABTS 1 O 1214-034 SEAT BACK OFFICER Seat Back Officer SCBA IMMI SmartDock 1 O 1220-006 SEAT MOUNTING OFFICER Seat Mounting Officer Fwd 3" 1 S 1297-002 POWER SEAT WIRING Power Seats Wiring Battery Direct 1 S 1273-001 SEAT BELT ORIENTATION CREW Seat Belt Orientation Crew Outboard Shoulder To Inboard Hip
1 S 1266-001 SEAT FORWARD FACING CENTER

LOCATION
Seat FFC Location (2) Ctr 1
O 1206-019 SEAT CREW FORWARD FACING
CENTER
Seat Crew FFC Seats Inc Battalion Flip-Up 2
O 1218-001 SEAT BACK FORWARD FACING
CENTER
Seat Back FFC Non-SCBA ABTS 2
O 1269-107 SEAT FRAME FORWARD FACING Seat Frm Fwd Fcg Short Dual 1 O 1281-112 SEAT FRAME FORWARD FACING

STORAGE ACCESS
Seat Frm Fwd Fcg Strg Acc Dr (2) R/L Sd Short 1
S 1224-002 SEAT MOUNTING FORWARD FACING
CENTER
Seat Mounting Forward Facing Center 1
S 1311-101 CAB FRONT UNDERSEAT STORAGE

ACCESS DOOR
Cab Frt Undrst Strg Acc Dr 1
S 1355-019 SEAT COMPARTMENT DOOR FINISH Seat Compartment Door Finish Multi-tone Silver Gray 1

CAB EXTERIOR
S 1511-200 WINDSHIELD WIPER SYSTEM Windshield Wiper System 1 S 1534-002 ELECTRONIC WINDSHIELD FLUID

LEVEL INDICATOR
Electronic Windshield Fluid Level Indicator 1
O 1103-004 CAB DOOR HARDWARE Cab Door Hardware Chrome w/Scuff Plate 1 O 1111-004 DOOR LOCKS Door Locks Power (4) Entry Doors 1 O 1113-003 DOOR LOCK LH EMS

COMPARTMENT
Door Lock LH EMS Compartment Hng Power 1
O 1114-003 DOOR LOCK RH EMS

COMPARTMENT
Door Lock RH EMS Compartment Hng Power 1
O 1112-003 POWER DOOR LOCK

COMPARTMENT ACTIVATION
Power Door Lock Cmpt Actv MUX 1
S 1503-200 GRAB HANDLES Grab Handles SS 18" 1
O 1504-039 REARVIEW MIRRORS Mirror Bus Style Ramco CRM-310-1750-CHCHR 1 S 1529-003 REARVIEW MIRROR HEAT SWITCH Rearview Mirror Heat Sw MUX 1 O 1513-010 CAB FENDER Cab Fender Alum Wide 1
S 1514-002 MUD FLAPS FRONT Mud Flaps Frt 1
O 1526-031 CAB EXTERIOR FRONT & SIDE

EMBLEMS
Cab Ext Frt & Side Emblems Spartan w/Side Shiploose 1

START / CHARGING SYSTEMS
S 5109-001 IGNITION Ign Mstr Sw w/Keyless Start 1
S 5101-021 BATTERY Batt (6) Group 31 Harris 1
S 5106-003 BATTERY TRAY Batt Tray (2) R/L Steel 1
S 5107-007 BATTERY BOX COVER Batt Box Cover (2) Steel w/Black Handles 1 S 5102-001 BATTERY CABLE Batt Cables 1
S 5108-010 BATTERY JUMPER STUD Batt Jumper Stud Frt LH Lwr Step 8" Apart 1 S 5104-002 ALTERNATOR Alternator Leece-Neville 320A 1
S 5105-001 STARTER MOTOR Starter Motor Delco 1

LINE VOLTAGE ELECTRICAL POWER DISTRIBUTION
O 5202-116 BATTERY CONDITIONER Batt Cond Kussmaul Auto Charge 40 LPC Shiploose w/12' Coil
1 O 5203-003 BATTERY CONDITIONER DISPLAY Batt Cond Display LH Cab Side Fwd 1 O 5209-039 ELECTRICAL INLET LOCATION Elec Inlet Location LH Cab Side Fwd Mid 1 S 5204-055 ELECTRICAL INLET Elec Inlet 120V 20A Auto Eject 1 O 5210-004 ELECTRICAL INLET CONNECTION Elec Inlet Conn to Batt Conditioner 1 O 5206-010 ELECTRICAL INLET COLOR Elec Inlet Color White 1

LIGHTING
S 5301-102 HEADLIGHTS Headlights 4 Headlamps LED 1
S 5337-001 HEADLIGHT LOCATION Headlights Below Frt Warn Lts 1 S 5303-004 FRONT TURN SIGNALS Frt Turn Signals Whelen 600 LED 1 S 5336-015 SIDE TURN/MARKER LIGHTS Side Turn/Marker Lts LED Tecniq S170 1 O 5302-024 MARKER & ICC LIGHTS Marker & ICC Lts Face Mnt LED Tecniq S170 No Bezel 1 O 5350-092 HEADLIGHT AND MARKER LIGHT

ACTIVATION
Hdlt & Mrkr Lt Actv Rkr Sw/DRL Ign Sw 1
O 5426-008 LIGHTBAR SWITCH Lightbar Sw Vista w/Clear Lt Cutoff 1 O 5305-351 INTERIOR OVERHEAD LIGHTS Interior Overhead Lts Weldon Red/Clear Split Lens LED 1 S 5388-003 INTERIOR OVERHEAD LIGHTING

ACTIVATION
Int Ovrhd Lt Actv Resp Dr & MUX 1
O 5403-051 LIGHTBAR PROVISION Lightbar Prov Wire & Mnt (2) Chassis Supply 1 O 5450N006
CAB FRONT LIGHTBAR MODEL Cab Front Lightbar Model Whelen F4NMINI (2) 1 S 5450-999 CAB FRONT LIGHTBAR Cab Front Lightbar - Configured in 5450M Subcategory 1 S 5450M002
FRONT LIGHTBAR LAYOUT Cab Front Lightbar Layout 1
O 5450X003
FRONT LIGHTBAR ORIENTATION Front Lightbar Orientation - Outboard/Aerial Mnt 1 O 5450L2-
002
FRONT LIGHTBAR LIGHT POSITION 2 Cab Front Lightbar Position 2 - Red LH Side 1 O 5450L4-
003
FRONT LIGHTBAR LIGHT POSITION 4 Cab Front Lightbar Position 4 - White 1 O 5450L5-
007
FRONT LIGHTBAR LIGHT POSITION 5 Cab Front Lightbar Position 5 - Red Steady Burn 1 O 5450L12-
003

FRONT LIGHTBAR LIGHT POSITION
12 Cab Front Lightbar Position 12 - White 1
O 5450L13-
002

FRONT LIGHTBAR LIGHT POSITION
13 Cab Front Lightbar Position 13 - Red 1
O 5450L15-
032

FRONT LIGHTBAR LIGHT POSITION
15 Cab Front Lightbar Position 15 - Red RH Side 1
O 5317-243 FRONT SCENE LIGHTS Frt Scene Lts FireTech FT-MB-12-FT-W 12V LED (2) White 1 O 5329-006 FRONT SCENE LIGHT LOCATION Frt Scene Lt Loc (2) Outboard Brow Pos 1 O 5335-003 FRONT SCENE LIGHTS ACTIVATION Frt Scene Lts Actv Vista 1 O 5306-065 SIDE SCENE LIGHTS Side Scene Lts Whelen 900 12V Super 24 LED Clear Gradient 1 O 5318-004 SIDE SCENE LIGHT LOCATION Side Scene Lt Loc Upper Mid Rwd 10" Roof Position 1 O 5316-007 SIDE SCENE ACTIVATION Side Scene Actv Indv Vista Buttons 1 S 5308-300 GROUND LIGHTS Ground Lts Tecniq T44 LED 1
O 5386-011 GROUND LIGHTING ACTIVATION Ground Lt Actv Resp Sd Dr & Rkr Sw 1 S 5309-003 LOWER CAB STEP LIGHTS Lwr Cab Step Lts Tecniq T44 LED 1 O 5382-007 INTERMEDIATE STEP LIGHTS Intermediate Step Lts Tecniq D06 LED 1 O 5310-002 MAP LIGHTS Map Lt Roxter RH Dash 1
S 5312-003 ENGINE COMPARTMENT LIGHT Engine Cmpt Work Lt LED (1) 1

OPTICAL WARNING DEVICES
S 5406-119 DO NOT MOVE APPARATUS LIGHT Do Not Move App Lt Flashing Red Tecniq K50 LED w/Alarm 1 S 5422-002 MASTER WARNING SWITCH Mstr Warn Sw MUX 1
S 5409-002 HEADLIGHT FLASHER Headlight Flasher Alternating 1 O 5425-018 HEADLIGHT FLASHER SWITCH Headlight Flasher Sw Pnl 1 O 5401-002 INBOARD FRONT WARNING LIGHTS Inboard Frt Warn Lts Whelen 600 LED Chrm Bezel 1 O 5413-002 INBOARD FRONT WARNING LIGHTS
COLOR
Inboard Frt Warn Lts Color Red 1
O 5423-003 FRONT WARNING SWITCH Frt Warn Sw Vista 1
O 5404-002 INTERSECTION WARNING LIGHTS Intersection Warn Lts Whelen 600 Super LED 1 O 5419-002 INTERSECTION WARNING LIGHTS
COLOR
Int Warn Lts Color Red 1
O 5420-002 INTERSECTION WARNING LIGHTS

LOCATION
Intersection Warn Lts Location Bumper Tail Rwd 1
O 5402-002 SIDE WARNING LIGHTS Side Warn Lts Whelen 600 Super LED 1 O 5418-002 SIDE WARNING LIGHTS COLOR Side Warn Lts Color Red 1 O 5412-009 SIDE WARNING LIGHTS LOCATION Side Warn Lts Location Lwr Mid Fwd Position 1 O 5424-003 SIDE AND INTERSECTION WARNING
SWITCH
Side & Intersection Warn Sw Vista 1
O 5449-049 REAR WARNING LIGHTS Rr Warn Lts Prewire & Cutout Whelen TACTL5 Traf Advsr Sw Pnl MstrPwr
1 AUDIBLE WARNING DEVICES
O 5510-004 SIREN CONTROL HEAD Siren Ctrl Head Whelen 295HFS2 1 O 5514-002 STEERING WHEEL HORN BUTTON

SELECTOR SWITCH
Horn Btn Sel Sw Elec Horn/Air Horn 1
O 5527-004 AUDIBLE WARNING RH FOOT
SWITCH
Audible Warning RH Foot Switch Siren 1
O 5527C001

MECHANICAL SIREN FOOT SWITCH
RH
Mechanical Siren Foot Switch RH Linemaster 491-S 1
O 5527D001

MECHANICAL SIREN FOOT SWITCH

RH LOCATION
Mechanical Siren Foot Switch RH Location Temporary
Behind Dash Panel Coiled
1 S 5512-042 AIR HORN AUXILIARY ACTIVATION Air Horn Actv PB Sw Pnl 1 O 5513-503 MECHANICAL SIREN

BRAKE/AUXILIARY ACTIVATION
Mech Siren Brk (2) Sws 1
O 5532-001 MECHANICAL SIREN INTERLOCK Mechanical Siren Interlock Master Warn Only 1 S 5505-002 BACK-UP ALARM Back-Up Alarm Ecco 575 1

INSTRUMENTATION
S 5601-041 INSTRUMENTATION Instrumentation Standard 1
S 5624-001 BACKLIGHTING COLOR Backlighting Color Red 1

COMMUNICATIONS SYSTEMS
O 5701-300 RADIO Radio Jensen WB/AM/FM/iPod/Sat/BT 1
O 5736-200 RADIO LOCATION Radio Overhead RH 1
O 5707-003 AM/FM ANTENNA AM/FM Antenna RH Fwd Cab Roof 1 O 5737-200 RADIO SPEAKERS Radio Speakers (4) Front/Rear 1 O 5726-002 CAMERA LEFT HAND Camera LH Teardrop 1
O 5727-002 CAMERA RIGHT HAND Camera RH Teardrop 1
O 5728-009 CAMERA REAR Camera HD Rear Box 1
O 5731-004 CAMERA DISPLAY Camera Display on Vista 1
O 5732-002 CAMERA SPEAKER Camera Speaker 1
O 5702-023 TWO-WAY RADIOS Two-Way Radio Exterior Conduit to Under RH Seat 1 S 5020-002 PANEL LAYOUT Panel Layout 1

ADDITIONAL EQUIPMENT
S 8814-002 CAB EXTERIOR PROTECTION Cab Exterior Protection Front 1 S 8806-001 FIRE EXTINGUISHER Fire Extinguisher Shiploose 1 O 8807-002 ROAD SAFETY KIT Road Safety Kit Shiploose 1
S 8810-001 DOOR KEYS Door Keys for Manual Locks (4) 1

SALES ADMIN
S 8003-197 WARRANTY Warranty Cab and Chassis (2) Year RFW0102 1 S 8030-006 CHASSIS OPERATION MANUAL Chassis Operation Manual Digital Copy (2) 1 S 8031-024 ENGINE & TRANSMISSION

OPERATION MANUAL
Eng & Trans Operation Man Eng Hard Copy/Trans
Digital/Eng Owner Digital
1 O 8032-018 ENGINE SERVICE MANUAL Engine Service Manual Hard Copy Cummins Lg Displacement
1 O 8033-002 TRANSMISSION SERVICE MANUAL Transmission Service Manual Hard Copy Allison 4000 EVS 1 S 8805-007 CAB/CHASSIS AS BUILT WIRING

DIAGRAMS
Cab/Chassis As Built Wiring Diagrams Digital Copy (2) 1 S 8039-001 SALES TERMS Sales Terms 1

ENGINEERING
O 9005-002 DRIVELINE LAYOUT CONFIRMATION Driveline Layout Confirmation Required 1 Front Lightbar Layout
5450M-002 Cab Front Lightbar Layout
Option Description
NO Cab Front Lightbar Position 1 Filter
NO Cab Front Lightbar Position 2 Filter
NO Cab Front Lightbar Position 3 Filter
NO Cab Front Lightbar Position 4 Filter
NO Cab Front Lightbar Position 5 Filter
NO Cab Front Lightbar Position 6 Filter
NO Cab Front Lightbar Position 11 Filter
NO Cab Front Lightbar Position 12 Filter
NO Cab Front Lightbar Position 13 Filter
NO Cab Front Lightbar Position 14 Filter
NO Cab Front Lightbar Position 15 Filter RH Side
NO Cab Front Lightbar Position 16 Filter Rear RH Corner NO Cab Front Lightbar Position 7 Filter RH Side
NO Cab Front Lightbar Position 8 Filter Rear RH Corner
NO Cab Front Lightbar Position 9 Filter Rear LH Corner
NO Cab Front Lightbar Position 10 Filter LH Side
Cab Front Lightbar Position 1 - Blank Rear LH Corner
Cab Front Lightbar Position 2 - Red LH Side
Cab Front Lightbar Position 3 - Red Front LH Corner
Cab Front Lightbar Position 4 - White
Cab Front Lightbar Position 5 - Red Steady Burn
Cab Front Lightbar Position 6 - Red Front RH Corner
Cab Front Lightbar Position 7 - Blank RH Side
Cab Front Lightbar Position 8 - Blank RH Corner
Cab Front Lightbar Position 10 - Blank LH Side
Cab Front Lightbar Position 9 - Blank Rear LH Corner
Cab Front Lightbar Position 11 - Red Front LH Corner
Cab Front Lightbar Position 12 - White
Cab Front Lightbar Position 13 - Red
Cab Front Lightbar Position 14 - Red Front RH Corner
Cab Front Lightbar Position 15 - Red RH Side
Cab Front Lightbar Position 16 - Blank Rear RH Corner

FRONT LIGHTBAR LEGEND INSERT
5020-002 Panel Layout
Option Description

SWITCH PANEL - MISC PANELS

LEGEND LOCATION
SW PNL CENTER 8 SWITCHES UPPER LH 99"

WHELEN TACTL CONTROLLER CUTOUT
SIREN CONTROL HEAD WHELEN 295HFS2

CLIMATE CTRLS DASH ROTARY UNDERDASH HTR DEFROSTER CTR PNL AIR HORN PB 2010 94"
USB POWER POINT DASH MNT (2) BATT DIR 2010 94"
PWR POINT DASH MNT (5) BATT DIR
USB POWER POINT DASH MNT BATT DIR (3)
PWR POINT DASH MNT (4) BATT DIR
POWER POINT DASH MNT (1) BATT DIR
PWR POINT DASH MNT (4) BATT DIR
MUX DISPLAY (1) DRIVER PNL 2010
SWITCH PANEL FAR LH (5) SWITCH 2010

LH PTO 'AERIAL MASTER'

PTO AERIAL CONTROL RKR ACTV 'AERIAL PTO'

GROUND LTS RKR SW MUX

HDLT & MRKR LT ACTV DIMMER SW
HDLT & MRKR LT RKR SW 94/96

HEADLIGHT FLASHER SW

WINDSHIELD WIPER SYSTEM SINGLE MOTOR
Rear Axle Differential Ctrl Interaxle Lock

HORN RING SEL SW ELEC HORN/AIR HORN

MECH SIREN BRK RKR SW

MECH SIREN BRK RKR SW
Specification
0100-012
MODEL
The chassis shall be a Gladiator model. The cab and chassis shall include design considerations for multiple emergency vehicle applications, rapid transit and maneuverability. The chassis shall be manufactured for heavy duty service with the strength and capacity to support a fully laden apparatus, one hundred (100) percent of the time.
8011-024

MODEL YEAR
The chassis shall have a vehicle identification number that reflects a 2024 model year. 8001-001

COUNTRY OF SERVICE
The chassis shall be put in service in the country of United States of America (USA).

The chassis will meet applicable U.S.A. federal motor vehicle safety standards per CFR Title 49 Chapter V Part 571 as clarified in the incomplete vehicle book per CFR Title 49 Chapter V Part 568 Section 4 which accompanies each chassis. The chassis manufacturer is not responsible for compliance to state, regional, or local regulations. Dealers should identify those regulations and order any necessary optional equipment from the chassis manufacturer or their OEM needed to be in compliance with those regulations.
8017-009

CAB AND CHASSIS LABELING LANGUAGE
The cab and chassis shall include the applicable caution, warning, and safety notice labels with text to be written in English. All applicable caution, warning, and safety notice labels shall be Innovative Controls brand. Where applicable to the location within the specific layout and label package of the cab and chassis, the labels shall include decorative chrome bezels. Designs shall include bezels that fit individual labels or packaged configurations of labels in certain common locations.

The following labels shall be Innovative Controls brand, each including a decorative chrome bezel (where applicable):
 Shoreline
 Aerial Stowed
 Aerial Breakers 2
 Air Conditioner
 Cab Tilt Plate
 Air Compressor Breaker
 Battery Conditioner Breaker
 Helmet Caution
 Horn Tag
 Q2B Tag
 Load Center Plate
 Not a Step Label
 Occupancy Tag
 Do Not Move
 Occupants Must Be Seated
 Do Not Stand
 Danger Do Not Weld
 Danger--Untrained Operator
 DEF Fill Access (Including Additional 2907 Optional Labels)  Battery Direct
 Kneeling
 IFS Air Fault
 Engine Brake
 Retarder
 LR 100 Amp Node
 300 Amp EPU
 100 Amp Front O/R Node
 100 Amp T/T Node
 100 Amp RR O/R Node
 10 Amp EPU
 Master Power
 12 Volt Power
 Aerial Hours
 Pump In Drive
Windshield Washer Fluid
8006-011

APPARATUS TYPE
The apparatus shall be a Quint vehicle designed for emergency service use. The apparatus shall include a permanently mounted fire pump which has a minimum rated capacity of 750 gallons per minute (3000 L/min), a water tank, a hose storage area, a compliment of ground ladders, and an aerial ladder or elevating platform with a permanently mounted waterway that shall be rear mounted thus providing the following vehicle benefits:
 Improved mobility vs. mid-ship mounted units, due to shorter overall travel length and wheelbase.
 Increased compartment space, hose load, and water capacity in the body, resulting from ladder being raised to clear the cab.
 Shorter vehicle wheelbase.

Shorter overall length of vehicle.
8008-001

VEHICLE TYPE
The chassis shall be manufactured for use as a straight truck type vehicle and designed for the installation of a permanently mounted apparatus behind the cab. The apparatus of the vehicle shall be supplied and installed by the apparatus manufacturer.
8008A-000

VEHICLE ANGLE OF APPROACH PACKAGE
The angle of approach of the apparatus shall be a minimum of 8.00 degrees.

NFPA1901 Angle of Approach definition:
“To determine the angle of approach, place a thin steel strip against the front of the tires where they touch the ground or stretch a tight string from one front tire to the other at the front where they touch the ground. Determine the lowest point (component or equipment) on the vehicle forward of the front tire that would make the smallest angle of approach. Hang a plumb bob from the lowest point and mark the point on the ground where the point of the plumb bob touches. Measure the vertical distance from the ground to the point where the plumb bob was hung (distance V). Measure the horizontal distance from the plumb bob point to the steel strip or string running from front tire to front tire (distance H). Divide the vertical distance by the horizontal distance. The ratio of V/H is the tangent of the angle of approach.

If the ratio is known, the angle of approach can be determined from a table of trigonometric functions of angles or from a math calculator. The standard requires a minimum angle of approach of 8.00 degrees:
since the tangent of 8.00 degrees is 0.1405, if V divided by H is 0.1405 or larger, the angle of approach is

8.00 degrees or greater.”
0104-003

AXLE CONFIGURATION
The chassis shall feature a 6 x 4 axle configuration consisting of a tandem rear drive axle set with a single front steer axle.
0101-016

GROSS AXLE WEIGHT RATINGS FRONT
The front gross axle weight rating (GAWR) of the chassis shall be 23,000 pounds.

This front gross axle weight rating shall be adequate to carry the weight of the completed apparatus including all equipment and personnel.
0102-010

GROSS AXLE WEIGHT RATINGS REAR
The rear gross axle weight rating (GAWR) of the chassis shall be 52,000 pounds.

This rear gross axle weight rating shall be adequate to carry the weight of the completed apparatus including all equipment and personnel.
8010-201

PUMP PROVISION
The chassis shall include provisions to mount a drive line pump in the middle of the chassis, behind the cab, more commonly known as the midship location. Chassis driveline pump provisions shall include an interlock feature for automatic setting of the park brake when the vehicle is shifted into pump mode while the transmission is in neutral and the transmission output speed translates to less than 1 mph.

When the conditions are met the driver side parking brake valve shall activate. Once shifted to road mode the condition for electric automatic brake engagement is no longer present and the driver’s parking brake control valve shall function normally.
8009-004

WATER & FOAM TANK CAPACITY
The chassis shall include a carrying capacity of up to 750 gallons (2839 liters). The water and/or foam tank(s) shall be supplied and installed by the apparatus manufacturer. 1000-004

CAB STYLE
The cab shall be a custom, fully enclosed, MFD model with a 10.00 inch raised roof over the driver, officer, and crew area, designed and built specifically for use as an emergency response vehicle by a company specializing in cab and chassis design for all emergency response applications. The cab shall be designed for heavy-duty service utilizing superior strength and capacity for the application of protecting the occupants of the vehicle. This style of cab shall offer up to eight (8) seating positions.

The cab shall incorporate a fully enclosed design with side wall roof supports, allowing for a spacious cab area with no partition between the front and rear sections of the cab. To provide a superior finish by reducing welds that fatigue cab metal; the roof, the rear wall and side wall panels shall be assembled using a combination of welds and proven industrial adhesives designed specifically for aluminum fabrication for construction.

The cab shall be constructed using multiple aluminum extrusions in conjunction with aluminum plate, which shall provide proven strength and the truest, flattest body surfaces ensuring less expensive paint repairs if needed. All aluminum welding shall be completed to the American Welding Society and ANSI D1.2-96 requirements for structural welding of aluminum.

All interior and exterior seams shall be sealed for optimum noise reduction and to provide the most favorable efficiency for heating and cooling retention.

The cab shall be constructed of 5052-H32 corrosion resistant aluminum plate. The cab shall incorporate tongue and groove fitted 6061-T6 0.13 & 0.19 inch thick aluminum extrusions for extreme duty situations. A single formed, one (1) piece extrusion shall be used for the “A” pillar, adding strength and rigidity to the cab as well as additional roll-over protection. The cab side walls and lower roof skin shall be 0.13 inch thick; the rear wall and raised roof skins shall be 0.09 inch thick; the front cab structure shall be 0.19 inch thick.

The exterior width of the cab shall be 99.40 inches wide with a minimum interior width of 91.00 inches.

The overall cab length shall be 131.10 inches with 54.00 inches from the centerline of the front of the axle to the back of the cab.

The cab interior shall be designed to afford the maximum usable interior space and attention to ergonomics with hip and legroom while seated which exceeds industry standards. The crew cab floor shall be flat across the entire walking area for ease of movement inside the cab.

The cab shall offer an interior height of 57.50 inches from the front floor to the headliner in the nonraised roof area and a rear floor to headliner height of 65.00 inches in the raised roof area, at a minimum.

The cab shall offer an interior measurement at the floor level from the rear of the engine tunnel to the rear wall of the cab of 49.88 inches. All interior measurements shall include the area within the interior trimmed surfaces and not to any unfinished surface.

The cab shall include a driver and officer area with two (2) cab doors large enough for personnel in full firefighting gear. The front doors shall offer a clear opening of 40.25 inches wide X 53.50 inches high, from the cab floor to the top of the door opening. The cab shall also include a crew area with up to two (2) cab doors, also large enough for personnel in full firefighting gear. The rear doors shall offer a clear opening of 32.25 inches wide X 61.00 inches high, from the cab floor to the top of the door opening.

The cab shall incorporate a progressive two (2) step configuration from the ground to the cab floor at each door opening. The progressive steps are vertically staggered and extend the full width of each step well allowing personnel in full firefighting gear to enter and exit the cab easily and safely.

The first step for the driver and officer area shall measure approximately 11.50 inches deep X 31.13 inches wide. The intermediate step shall measure approximately 8.50 inches deep X 32.50 inches wide.

The height from the first step to the intermediate step and the intermediate step to the cab floor shall not exceed 11.00 inches.

The first step for the crew area shall measure approximately 11.50 inches deep X 20.44 inches wide.

The intermediate step shall measure approximately 10.25 inches deep X 22.75 inches wide. The height from the first step to the intermediate step and the intermediate step to the cab floor shall not exceed

12.80 inches.
1501-002

CAB FRONT FASCIA
The front cab fascia shall be constructed of 5052-H32 Marine Grade, 0.13 of an inch thick aluminum plate which shall be an integral part of the cab.

The cab fascia will encompass the entire front of the aluminum cab structure from the bottom of the windshield to the bottom of the cab and shall be the “Classic” design.

The front cab fascia shall include two (2) molded plastic modules on each side accommodating a total of up to four (4) Hi/Low beam headlights and two (2) turn signal lights or up to four (4) warning lights. A chrome plated molded plastic bezel shall be provided on each side around each set of four lamps. 1518-025

FRONT GRILLE
The front cab fascia shall include a classic box style, 304 stainless steel front grille. The grille shall measure 55.45 wide X 33.50 inches high X 1.50 inches deep. The upper portion of the grille shall be hinged to provide service access behind the grille. The grille shall include a minimum free air intake of 750.00 square inches.
1551-002

CAB UNDERCOAT
There shall be a rubberized undercoating applied to the underside of the cab that provides abrasion protection, sound deadening and corrosion protection.
1552-002

CAB SIDE DRIP RAIL
There shall be a drip rail along the top radius of each cab side. The drip rails shall help prevent water from the cab roof running down the cab side.
1521-001

CAB PAINT EXTERIOR
The cab shall be painted prior to the installation of glass accessories and all other cab trim to ensure complete paint coverage and the maximum in corrosion protection of all metal surfaces.

All metal surfaces on the entire cab shall be ground by disc to remove any surface oxidation or surface debris which may hinder the paint adhesion. Once the surface is machine ground a high quality acid etching of base primer shall be applied. Upon the application of body fillers and their preparation, the cab shall be primed with a coating designed for corrosion resistance and surface paint adhesion. The maximum thickness of the primer coat shall be 2.00 mils.

The entire cab shall then be coated with an intermediate solid or epoxy surfacing agent that is designed to fill any minor surface defects, provide an adhesive bond between the primer and the paint and improve the color and gloss retention of the color. The finish to this procedure shall be a sanding of the cab with 360 grit paper followed by sealing the seams with SEM brand seam sealer.

The cab shall then be painted the specific color designated by the customer with an acrylic urethane type system designed to retain color and resist acid rain and most atmospheric chemicals found on the fire ground or emergency scene. The paint shall have a minimum thickness of 2.00 mils, followed by a clear top coat not to exceed 2.00 mils. The entire cab shall then be baked at 180 degrees for one (1) hour to speed the curing process of the coatings.
1533-002

CAB PAINT MANUFACTURER
The cab shall be painted with Sikkens paint.
1522-001

CAB PAINT PRIMARY/LOWER COLOR
The primary/lower paint color shall be:
8013-056

CAB PAINT WARRANTY
Purchaser shall receive a Paint and Finish (Exterior Clear coated) Ten (10) Years limited warranty in accordance with, and subject to, warranty certificate RFW0710. The warranty certificate is incorporated by reference into this proposal, and included with this proposal or available upon request. 1334-036

CAB PAINT INTERIOR
The visible interior cab structure surfaces shall be painted with a multi-tone silver gray texture finish. 1005-001

CAB ENTRY DOORS
The cab shall include four (4) entry doors, two (2) front doors and two (2) crew doors designed for ease of entering and egress when outfitted with an SCBA. The doors shall be constructed of extruded aluminum with a nominal thickness of 0.13 inch. The exterior skins shall be constructed of 0.13 inch aluminum plate.

The doors shall include a double rolled style automotive rubber seal around the perimeter of each door frame and door edge which ensures a weather tight fit.

All door hinges shall be hidden within flush mounted cab doors for a pleasing smooth appearance and perfect fit along each side of the cab. Each door hinge shall be piano style with a 0.38 inch pin and shall be constructed of stainless steel.
1101-102

CAB ENTRY DOOR TYPE
All cab entry doors shall be barrier clear design resulting in exposed lower cab steps. The doors shall provide approximately 32.00 inches of clearance from the ground to the bottom of the door so cab doors may be opened un-hindered by most obstacles encountered, such as guard rails along interstate highways.

Entry doors shall include Pollak mechanical plunger style switches for electrical component activation. 1322-007

CAB INSULATION
The cab ceiling and walls shall include a nonwoven polyester fiber insulation. The insulation shall act as a barrier absorbing noise as well as assisting in sustaining the desired climate within the cab interior. 1556-009

LH MID EMS COMPARTMENT
The cab shall include a compartment located in the middle of the wall above the left side wheel well.

The inner rear corner of the compartment shall be chamfered at a 45-degree angle to eliminate the square corner. The chamfered corner shall be cut at a width and depth of 7.00 inches the full height of the compartment. This compartment shall be offset and measure 17.00 inches just inside the door opening offset to 24.00 inches wide X 26.00 inches high X 25.00 inches deep. 1558-007

LH MID EMS EXTERIOR ACCESS
The cab shall include a hinged box pan door featuring a full length stainless steel piano style hinge and a bright aluminum tread plate inner panel located in the middle of the wall above the left side wheel well.

The compartment shall have a clear door opening of 15.00 inches wide X 24.00 inches high. 1560-002

LH MID EMS COMPARTMENT INTERIOR
The cab compartment located in the middle of the wall above the left side wheel well shall include solid aluminum walls with no interior access. This compartment shall be finished to customer specification. 1566-002

LH MID EMS COMPARTMENT DOOR HARDWARE
The left side EMS compartment door shall include a locking bent D-ring slam latch. There shall be a switch to activate the open compartment warning light in the cab in the event the door is left ajar. 1557-008

RH MID EMS COMPARTMENT
The cab shall include a compartment located in the middle of the wall above the right side wheel well.

RH MID EMS EXTERIOR ACCESS
The cab shall include a hinged box pan door featuring a full length stainless steel piano style hinge and a bright aluminum tread plate inner panel located in the middle of the wall above the right side wheel well.

The compartment shall have a clear door opening of 15.00 inches wide X 24.00 inches high. 1561-002

RH MID EMS COMPARTMENT INTERIOR
The cab compartment located in the middle of the wall above the right side wheel well shall include solid aluminum walls with no interior access. This compartment shall be finished to customer specification.
1567-002

RH MID EMS COMPARTMENT DOOR HARDWARE
The right side EMS compartment door shall include a locking bent D-ring slam latch. There shall be a switch to activate the open compartment warning light in the cab in the event the door is left ajar. 5384-002

MID EMS COMPARTMENT LIGHTING
The interior portion of each of the mid EMS compartments shall include compartment door activated LED lighting to illuminate all usable surfaces within each compartment. 1535-016

MID EMS COMPARTMENT EXTERIOR FINISH
The mid EMS compartment surfaces that are exposed to the interior of the cab shall be painted with a multi-tone silver gray texture finish.
1536-018

MID EMS COMPARTMENT INTERIOR FINISH
The interior of the mid EMS compartment shall be painted with a multi-tone silver gray texture finish. 1002-011

CAB ROOF TRENCH
The center section of the 10.00 inch raised roof shall include a 50.00 inch wide X 13.00 inch deep trench to accommodate the aerial device.
8004-033

CAB STRUCTURAL WARRANTY
Purchaser shall receive a Cab Structure (Aluminum) Ten (10) Years or 100,000 Miles limited warranty in accordance with, and subject to, warranty certificate RFW0602. The warranty certificate is incorporated by reference into this proposal, and included with this proposal or available upon request. 9001-006

CAB TEST INFORMATION
The cab shall have successfully completed the preload side impact, static roof load application and frontal impact without encroachment to the occupant survival space when tested in accordance with Section 4 of SAE J2420 COE Frontal Strength Evaluation Dynamic Loading Heavy Trucks, Section 5 of SAE J2422 Cab Roof Strength Evaluation Quasi –Static Loading Heavy Trucks and ECE R29 Uniform Provisions Concerning the Approval of Vehicles with regard to the Protection of the Occupants of the Cab of a Commercial Vehicles Annex 3 Paragraph 5.

The above tests have been witnessed by and attested to by an independent third party. The test results were recorded using cameras, high speed imagers, accelerometers and strain gauges. Documentation of the testing shall be provided upon request.
5000-018

ELECTRICAL SYSTEM
The chassis shall include a single starting electrical system which shall include a 12 volt direct current multiplexing system, suppressed per SAE J551. The wiring shall be appropriate gauge cross link with 311 degree Fahrenheit insulation. All SAE wires in the chassis shall be color coded and shall include the circuit number and function where possible. The wiring shall be protected by 275 degree Fahrenheit minimum high temperature flame retardant loom. All nodes and sealed Deutsch connectors shall be waterproof.
5008-072

OEM WIRING
The wiring system shall include a prewire for ECM park brake input and engine ground return circuits located behind the switch panel. The circuits shall include an extra 2.00 feet of wire and shall be labeled “ECM Park Brake Input”.
5006-002

APPARATUS WIRING PROVISION
An apparatus wiring panel shall be installed in the center dash area behind the rocker switch panel which shall include eight (8) open circuits consisting of three (3) 20 amp, one (1) 30 amp, three (3) 10 amp, and one (1) 15 amp circuit, with relays and breakers with trigger wires which shall be routed to the rocker switch panel.
5005-200

MULTIPLEX DISPLAY
The multiplex electrical system shall include a Weldon Vista IV display which shall be located on the left side of the dash in the switch panel. The Vista IV shall feature a full color LCD display screen which includes a message bar displaying the time of day and important messages requiring acknowledgement by the user which shall all be displayed on the top of the screen in the order they are received. There shall be eight (8) push button virtual controls, four (4) on each side of the display for the on-board diagnostics. The display screen shall be video ready for back-up cameras, thermal cameras, and DVD.

The Vista IV display shall offer varying fonts and background colors. The display shall be fully programmable to the needs of the customer and shall offer virtually infinite flexibility for screen configuration options.
5004-002

LOAD MANAGEMENT SYSTEM
The apparatus load management shall be performed by the included multiplex system. The multiplex system shall also feature the priority of sequences and shall shed electrical loads based on the priority list specifically programmed.
5622-003

DATA RECORDING SYSTEM
The chassis shall have a Weldon Vehicle Data Recorder (VDR) system installed. The system shall be designed to meet NFPA 1901 and shall be integrated with the Weldon Multiplex electrical system. The following information shall be recorded:
 Vehicle Speed
 Acceleration
 Deceleration
 Engine Speed
 Engine Throttle Position
 ABS Event
 Seat Occupied Status
 Seat Belt Status
 Master Optical Warning Device Switch Position
 Time
 Date
Each portion of the data shall be recorded at the specified intervals and stored for the specified length of time to meet NFPA 1901 guidelines and shall be retrievable by connecting a laptop computer to the VDR system. The laptop connection shall be a panel mounted female type B USB connection point, remotely mounted in the left side foot well.
5031-013

ACCESSORY POWER
The electrical distribution panel shall include two (2) power studs. The studs shall be size #10 and each of the power studs shall be circuit protected with a fuse of the specified amperage. One (1) power stud shall be capable of carrying up to a 40 amp battery direct load. One (1) power stud shall be capable of carrying up to a 15 amp ignition switched load. The two (2) power studs shall share one (1) #10 ground stud.

An OEM body connections bracket shall be installed on the chassis near the left hand battery box. The bracket shall include one (1) set each of a 350 amp master power switched and 300 amp battery direct power and ground studs. The 300 amp & 350 amp studs will not have any fuse protection and will be the responsibility of anyone using these studs to have fuse protection for each load attached. The studs will be labeled with max available amperage.
5030-037

AUXILIARY ACCESSORY POWER
An auxiliary ten (10) position blade type fuse panel shall be installed behind the officer’s seat. The fuse panel shall be protected by a 40 amp fuse. The panel shall be capable of carrying up to a maximum 40 amp battery direct load. The fuse panel shall include an additional 5.00 feet of coiled wired for permanent relocation by the body builder.
5011-001

EXTERIOR ELECTRICAL TERMINAL COATING
All terminals exposed to the elements will be sprayed with a high visibility protective rubberized coating to prevent corrosion.
8014-002

ELECTRICAL SYSTEM WARRANTY
Purchaser shall receive an Electrical System Two (2) Years or 36,000 Miles limited warranty in accordance with, and subject to, warranty certificate RFW0202. The warranty certificate is incorporated by reference into this proposal, and included with this proposal or available upon request. 1701-172
ENGINE
The chassis engine shall be a Cummins X15 engine. The X15 engine shall be an in-line six (6) cylinder, four cycle diesel powered engine. The engine shall offer a rating of 605 horse power at 1800 RPM and shall be governed at 2100 RPM. The torque rating shall feature 1850 foot pounds of torque at 1000 RPM with 912 cubic inches (14.9 liter) of displacement.

The X15 engine shall feature a VGT™ Turbocharger, a high pressure common rail fuel system, fully integrated electronic controls with an electronic governor, and shall be EPA certified to meet the 2021 emissions standards using cooled exhaust gas recirculation and selective catalytic reduction technology.

The engine shall include an engine mounted combination full flow/by-pass oil filter with replaceable spin on cartridge for use with the engine lubrication system. The engine shall include Citgo brand Citgard 500, or equivalent 15W40 CK-4 low ash engine oil which shall be utilized for proper engine lubrication.

A wiring harness shall be supplied ending at the back of the cab. The harness shall include a connector which shall allow an optional harness for the pump panel. The included circuits shall be provided for a tachometer, oil pressure, engine temperature, hand throttle, high idle and a PSG system. A circuit for J1939 data link shall also be provided at the back of the cab. 1329-002

CAB ENGINE TUNNEL
The cab interior shall include an integrated engine tunnel constructed of 5052-H32 Marine Grade 0.19 of an inch thick aluminum alloy plate. The tunnel shall be a maximum of 46.50 inches wide X 29.00 inches high.
1731-002

DIESEL PARTICULATE FILTER CONTROLS
There shall be two (2) controls for the diesel particulate filter. One (1) control shall be for regeneration and one (1) control shall be for regeneration inhibit.
1718-002

ENGINE PROGRAMMING HIGH IDLE SPEED
The engine high idle control shall maintain the engine idle at approximately 1250 RPM when engaged. 1719-005

ENGINE HIGH IDLE CONTROL
The vehicle shall be equipped with a virtual Vista button and an automatic high-idle speed control. It shall be pre-set so when activated, it will operate the engine at the appropriate RPM to increase alternator output. This device shall operate only when the engine is running and the transmission is in neutral with the parking brake set. The device shall disengage when the operator depresses the brake pedal, or the transmission is placed in gear, and shall be available to manually or automatically re-engage when the brake is released, or when the transmission is placed in neutral. There shall be an indicator on the Vista display and control screen for the high idle speed control. 1710-001

ENGINE PROGRAMMING ROAD SPEED GOVERNOR
The engine shall include programming which will govern the top speed of the vehicle. 1713-010

AUXILIARY ENGINE BRAKE
A compression brake, for the six (6) cylinder engine shall be provided. A cutout relay shall be installed to disable the compression brake when in pump mode or when an ABS event occurs. The engine compression brake shall activate upon 0% accelerator when in operation mode and actuate the vehicle’s brake lights.

The engine shall utilize a variable geometry turbo (VGT) as an integrated auxiliary engine brake to offer a variable rate of exhaust flow, which when activated in conjunction with the compression brake shall enhance the engine's compression braking capabilities.
1708-007

AUXILIARY ENGINE BRAKE CONTROL
An engine compression brake control device shall be included. The electronic control device shall monitor various conditions and shall activate the engine brake only if all of the following conditions are simultaneously detected:
 A valid gear ratio is detected.
 The driver has requested or enabled engine compression brake operation.  The throttle is at a minimum engine speed position.
 The electronic controller is not presently attempting to execute an electronically controlled final drive gear shift.

The compression brake shall be controlled via an off/low/high virtual button through the Vista display and control screen. The multiplex system shall remember and default to the last engine brake control setting when the vehicle is shut off and re-started.
1720-003

ELECTRONIC ENGINE OIL LEVEL INDICATOR
The engine oil shall be monitored electronically and shall send a signal to activate a warning in the instrument panel when levels fall below normal. The warning shall activate in a low oil situation upon turning on the master battery and ignition switches without the engine running. 1715-004

FLUID FILLS
The front of the chassis shall accommodate fluid fill for the engine oil through the grille. This area shall also accommodate a check for the engine oil. The transmission, power steering, and coolant fluid fills and checks shall be under the cab. The windshield washer fill shall be accessible through the front left side mid step.
1735-001

ENGINE DRAIN PLUG
The engine shall include an original equipment manufacturer installed oil drain plug. 8002-001

ENGINE WARRANTY
The Cummins engine shall be warranted for a period of five (5) years or 100,000 miles, whichever occurs first.
1707-116

REMOTE THROTTLE HARNESS
An apparatus interface wiring harness for the engine and transmission pump interlocks shall be supplied with the chassis. The harness shall include a connector for connection to a chassis pump panel harness supplied by the body builder and shall terminate in the left frame rail behind the cab for connection by the body builder. The harness shall include circuits deemed for a pump panel and shall contain circuits for a hand throttle, and a multiplexed gauge. Separate circuits shall also be included for a pump control switch, “Pump Engaged” and “OK to Pump” indicator lights, open compartment ground, start signal, park brake ground, ignition signal, master power, clean power, customer ignition, air horn solenoid switch, high idle switch and high idle indicator light. The harness shall contain interlocks that will prevent shifting to road or pump mode unless the transmission output speed translates to less than 1 mph and the transmission is in neutral. The shift to pump mode shall also require the park brake be set. 1721-001

ENGINE PROGRAMMING REMOTE THROTTLE
The engine ECM (Electronic Control Module) discreet wire remote throttle circuit shall be turned off for use with a J1939 based pump controller or when the discreet wire remote throttle controls are not required.
1727-001

ENGINE PROGRAMMING IDLE SPEED
The engine low idle speed will be programmed at 700 rpm. 2801-010

ENGINE AIR INTAKE
The engine air intake system shall include an ember separator. This ember separator shall be designed to protect the downstream air filter from embers using a combination of unique flat and crimped metal screens packaged in a heavy duty galvanized steel frame. This multilayered screen shall trap embers and allow them to burn out before passing through the pack.

The engine air intake system shall also include an air cleaner mounted above the radiator. This air cleaner shall utilize a replaceable dry type filter element designed to prevent dust and debris from being ingested into the engine. A service cover shall be provided on the housing, reducing the chance of contaminating the air intake system during air filter service.

The air intake system shall include a restriction indicator light in the warning light cluster on the instrument panel, which shall activate when the air cleaner element requires replacement. 2704-016

ENGINE FAN DRIVE
The engine cooling system fan shall incorporate a thermostatically controlled, Horton fully variable type fan drive with SmartClutch J-1939 CAN controller.

The variable speed fan clutch only engages at the amount needed for proper cooling to facilitate improved vehicle performance, cab heating in cold climates, and fuel economy. The fan clutch design shall be fail-safe so that if the clutch drive fails the fan shall engage to prevent engine overheating due to the fan clutch failure. The fan speed shall include a J-1939 CAN clutch controller to receive signal from the engine control module to activate at variable rates of speed. Variable speeds shall be set through thermostatic and engine speed signals to run as efficiently and quietly as required to maintain temperature.
2701-021

ENGINE COOLING SYSTEM
There shall be a heavy-duty aluminum cooling system designed to meet the demands of the emergency response industry. The cooling system shall have the capacity to keep the engine properly cooled under all conditions of road and pumping operations. The cooling system shall be designed and tested to meet or exceed the requirements specified by the engine and transmission manufacturer and all EPA requirements. The complete cooling system shall be mounted to isolate the entire system from vibration or stress. The individual cores of the cooling system shall be mounted in a manner to allow expansion and contraction at various rates without inducing stress into the adjoining cores.

The cooling system shall be comprised of a charge air cooler to radiator serial flow package that provides the maximum cooling capacity for the specified engine as well as serviceability. The main components shall include a surge tank, a charge air cooler bolted to the front of the radiator, recirculation shields, a shroud, a fan, and required tubing.

The radiator shall be a down-flow design constructed with aluminum cores, plastic end tanks, and a steel frame. The radiator shall be equipped with a drain cock to drain the coolant for serviceability.

The cooling system shall include a one piece injected molded polymer fan with a three (3) piece fiberglass fan shroud.

The cooling system shall be equipped with a surge tank that is capable of removing entrained air from the system. The surge tank shall be equipped with a low coolant probe and rearward oriented sight glass to observe coolant in the system. A cold fill and observation line shall be included within the frame mounted translucent recovery bottle to monitor the level of the coolant. The surge tank shall have a dual seal cap that meets the engine manufacturer's pressure requirements and allows for expansion and recovery of coolant into a separate integral expansion chamber.

All radiator tubes shall be formed from aluminized steel tubing. Recirculation shields shall be installed where required to prevent heated air from reentering the cooling package and affecting performance.

The charge air cooler shall be a cross-flow design constructed completely of aluminum with cast tanks.

All charge air cooler tubes shall be formed from aluminized steel tubing and installed with silicone hump hoses and stainless steel “constant torque” style clamps meeting the engine manufacturer's requirements.

The radiator and charge air cooler shall be removable through the bottom of the chassis. 2711-005

ENGINE COOLING SYSTEM PROTECTION
The engine cooling system shall include a recirculation shield designed to act as a light duty skid plate below the radiator to provide additional protection for the engine cooling system from light impacts, stones, and road debris. The skid plate shall be painted to match the frame components. 2708-001

ENGINE COOLANT
The cooling package shall include Extended Life Coolant (ELC). The use of ELC provides longer intervals between coolant changes over standard coolants providing improved performance. The coolant shall contain a 50/50 mix of ethylene glycol and de-ionized water to keep the coolant from freezing to a temperature of -34 degrees Fahrenheit.

Proposals offering supplemental coolant additives (SCA) shall not be considered, as this is part of the extended life coolant makeup.
2707-002

ENGINE COOLANT FILTER
An engine coolant filter with a shut-off valve for the inlet and outlet shall be installed on the chassis. The location of the filter shall allow for easy maintenance.

Proposals offering engines equipped with coolant filters shall be supplied with standard non-chemical type particulate filters.
2706-003

ELECTRONIC COOLANT LEVEL INDICATOR
The instrument panel shall feature a low engine coolant indicator light which shall be located in the center of the instrument panel. An audible tone alarm shall also be provided to warn of a low coolant incident.
2705-002

ENGINE PUMP HEAT EXCHANGER
A single bundle type coolant to water heat exchanger shall be installed between the engine and the radiator. The heat exchanger shall be designed to prohibit water from the pump from coming in contact with the engine coolant. This shall allow the use of water from the discharge side of the pump to assist in cooling the engine.
2709-001

COOLANT HOSES
The cooling systems hose shall be formed silicone hose and formed aluminized steel tubing and include stainless steel constant torque band clamps.
2710-005

ENGINE COOLANT OVERFLOW BOTTLE
A remote engine coolant overflow expansion bottle shall be provided in the case of over filling the coolant system. The overflow bottle shall capture the expansion fluid or overfill rather than allow the fluid to drain on the ground.
2901-074

ENGINE EXHAUST SYSTEM
The exhaust system shall include an end-in end-out horizontally mounted single module after treatment device, and downpipe from the charge air cooled turbo. The single module shall include four temperature sensors, diesel particulate filter (DPF), urea dosing module (UL2), and a selective catalytic reduction (SCR) catalyst to meet current EPA standards. The selective catalytic reduction catalyst utilizes a diesel exhaust fluid solution consisting of urea and purified water to convert NOx into nitrogen, water, and trace amounts of carbon dioxide. The solution shall be mixed and injected into the system through the DPF and SCR.

The system shall utilize 0.07 inch thick stainless steel exhaust tubing between the engine turbo and the DPF. Zero leak clamps seal all system joints between the turbo and DPF.

The single module after treatment through the end of the tailpipe shall be connected with zero leak clamps. The discharge shall terminate horizontally on the right side of the vehicle ahead of the rear tires.

The exhaust system after treatment module shall be mounted below the frame in the inboard position.

The mounting brackets shall be mounted on the inside of the frame. 2907-003

DIESEL EXHAUST FLUID TANK
The exhaust system shall include a molded cross linked polyethylene tank for Diesel Exhaust Fluid (DEF). The tank shall have a capacity of six (6) usable gallons and shall be mounted on the left hand side of the chassis frame behind the batteries below the frame.

The DEF tank shall be designed with capacity for expansion in case of fluid freezing. Engine coolant, which shall be thermostatically controlled, shall be run through lines in the tank to help prevent the DEF from freezing and to provide a means of thawing the fluid if it should become frozen.

The tank fill tube shall be routed under the rear of the cab with the fill neck and splash guard accessible in the top rear step.
2902-010

ENGINE EXHAUST ACCESSORIES
An exhaust temperature mitigation device shall be shipped loose for installation by the body manufacturer on the vehicle. The temperature mitigation device shall lower the temperature of the exhaust by combining ambient air with the exhaust gasses at the exhaust outlet. 2906-002

ENGINE EXHAUST WRAP
The exhaust tubing between the engine turbo and the diesel particulate filter (DPF) shall be wrapped with a thermal cover in order to retain the necessary heat for DPF regeneration. The exhaust wrap shall also help protect surrounding components from radiant heat which can be transferred from the exhaust.

The exhaust flex joint shall not include the thermal exhaust wrap. 8018-002

EMISSIONS SYSTEMS WARRANTY
Purchaser shall receive a Regulated Emissions Systems Five (5) Years or 100,000 Miles limited warranty in accordance with, and subject to, warranty certificate RFW0140. The warranty certificate is incorporated by reference into this proposal, and included with this proposal or available upon request. 1801-018

TRANSMISSION
The drive train shall include an Allison model EVS 4000 torque converting, automatic transmission which shall include electronic controls and an output retarder. The transmission shall feature two (2) 10- bolt PTO pads located on the converter housing.

The transmission shall include two (2) internal oil filters which shall offer Castrol TranSynd™ synthetic TES 295 transmission fluid which shall be utilized in the lubrication of the EVS transmission. An electronic oil level sensor shall be included with the readout located in the shift selector.

The transmission gear ratios shall be:
1st 3.51:1
2nd 1.91:1
3rd 1.43:1
4th 1.00:1
5th 0.74:1
6th 0.64:1 (if applicable)
Rev 4.80:1
1806-001

TRANSMISSION MODE PROGRAMMING
The transmission, upon start-up, will automatically select a four (4) speed operation. The fifth speed over drive shall be available with the activation of the mode button on the shifting pad. 1811-004

TRANSMISSION FEATURE PROGRAMMING
The Allison Gen V/VI-E transmission EVS group package number 127 shall contain the 198 vocational package in consideration of the duty of this apparatus as a pumper. This package shall incorporate an automatic neutral with selector override. This feature commands the transmission to neutral when the park brake is applied, regardless of drive range requested on the shift selector. This requires re-selecting drive range to shift out of neutral for the override.

This package shall be coupled with the use of a split shaft PTO and incorporate pumping circuits. These circuits shall be used allowing the vehicle to operate in the fourth range lockup while operating the pump mode due to the 1 to 1 ratio through the transmission, therefore the output speed of the engine is the input speed to the pump. The pump output can be easily calculated by using this input speed and the drive ratio of the pump itself to rate the gallons of water the pump can provide.

A transmission interface connector shall be provided in the cab. This package shall contain the following input/output circuits to the transmission control module. The Gen V/VI-E transmission shall include prognostic diagnostic capabilities. These capabilities shall include the monitoring of the fluid life, filter change indication, and transmission clutch maintenance.

Function ID Description Wire assignment
Inputs
C PTO Request 142
J Fire Truck Pump Mode (4th Lockup) 122 / 123
Outputs
C Range Indicator 145 (4th)
G PTO Enable Output 130
Signal Return 103
1807-005

TRANSMISSION SHIFT SELECTOR
An Allison pressure sensitive range selector touch pad shall be provided and located to the right of the driver within clear view and easy reach. The shift selector shall have a graphical Vacuum Florescent Display (VFD) capable of displaying two lines of text. The shift selector shall provide mode indication and a prognostic indicator (wrench symbol) on the digital display. The prognostics monitor various operating parameters and shall alert you when a specific maintenance function is required. 1815-002

ELECTRONIC TRANSMISSION OIL LEVEL INDICATOR
The transmission fluid shall be monitored electronically and shall send a signal to activate a warning in the instrument panel when levels fall below normal.
1812-004

TRANSMISSION RETARDER CONTROL
The Allison transmission retarder shall be engaged with the first one-third at 0% throttle and the remaining two-thirds shall be modulated by brake pedal actuation. The system shall include a retarder on/off virtual button on the Vista display and control screen. The engagement of the retarder shall activate the brake lights. The retarder shall be inactive during pump mode. 1816-004

TRANSMISSION RETARDER CAPACITY LEVEL
The transmission retarder shall be programmed so the maximum retardation shall be at the high capacity level.
1814-002

TRANSMISSION PRE-SELECT WITH AUXILIARY BRAKE
When the auxiliary brake is engaged, the transmission shall automatically shift to second gear to decrease the rate of speed assisting the secondary braking system and slowing the vehicle. 1808-007

TRANSMISSION COOLING SYSTEM
The transmission shall include a water to oil cooler system located in the cooling loop between the radiator and the engine. The transmission cooling system shall meet all transmission manufacturer requirements. The transmission cooling system shall feature continuous flow of engine bypass water to maintain uninterrupted transmission cooling.
1817-001

TRANSMISSION DRAIN PLUG
The transmission shall include an original equipment manufacturer installed magnetic transmission fluid drain plug.
8005-001

TRANSMISSION WARRANTY
The Allison EVS series transmission shall be warranted for a period of five (5) years with unlimited mileage. Parts and labor shall be included in the warranty. 2004-004
LH PTO
A PTO shall be installed on the transmission by the OEM. 2001-109

LH PTO MODEL
A ten (10) bolt Chelsea model 280-GGFJP-B5XD heavy duty transmission driven PTO shall be installed. The clutched shifted PTO is designed specifically for the Allison world transmission and provides an intermittent and continuous torque rating of 360 lb. ft. 2005-008

PTO LOCATION
The transmission shall have two (2) power take off (PTO) mounting locations, one (1) in the 8:00 o’clock position and one (1) in the 1:00 o’clock position. 2015-030

LH PTO CONTROL
Switches for the power take off shall be wired to the V-mux node to be used by the OEM. There shall be an on/off rocker switch labeled “Aerial Master” wired to a V-mux input and output with integral light wired to the v-mux input terminal of the switch that shall illuminate when the switch in on and the vmux output is active.

There shall be an on/off rocker switch labeled “Aerial PTO” activated by the “Aerial Master” rocker switch with an input to the V-mux node when the switch is on and an integral light activated by an independent V-mux output. The switches shall be located on dash. 3001-017

DRIVELINE
All drivelines shall be heavy duty metal tube and equipped with MSI 1810 series universal joints for the main drivelines, and 1710 series for the inter-axle shaft. The shafts shall be dynamically balanced prior to installation to alleviate future vibration. In areas of the driveline where a slip shaft is required, the splined slip joint shall be coated with Glide Coat®. The drivelines shall include Meritor brand u-joints with thrust washers.
3005-074

MIDSHIP PUMP / GEARBOX
A temporary jackshaft driveline shall be installed by the chassis manufacturer to accommodate the midship split shaft pump as specified by the apparatus manufacturer. Holes shall be provided in the frame as specified by the OEM for mounting a Smeal aerial pump module.

See PDF for specific hole pattern.
3008-085

MIDSHIP PUMP / GEARBOX MODEL
The midship pump/gearbox provisions shall be for a Waterous CSUC20 pump. 3048-006

MIDSHIP PUMP GEARBOX DROP
The Waterous pump gearbox shall have a “B” (short) drop length. 3009-007

MIDSHIP PUMP RATIO
The ratio for the midship pump shall be 2.27:1.
3010-1140

MIDSHIP PUMP LOCATION C/L SUCTION TO C/L REAR AXLE
The midship pump shall be located so the dimension from the centerline of the suction to the centerline of the rear axle is 114.00 inches.
5013-005

PUMP SHIFT CONTROLS
One (1) electric over air pump shift control panel shall be located in the left hand side knee area below the dash. The following shall be provided on the panel: a three (3) position locking toggle switch; an engraved PUMP ENGAGED identification light; and an engraved OK TO PUMP identification light.

The pump shift control panel shall be black with a yellow border outline and shall include pump instructions. An instruction plate describing the transmission shift selector position used for pumping shall be provided and located so it can be read from the driver’s position per NFPA 16.10.1.3. The pump mode shall be selected when the switch is in the up position and road mode shall be selected when the switch is in the down position.

The center switch position shall exhaust air from both pump and road sides of the pump gear box shift cylinder.
3049-003

PUMP SHIFT CONTROL PLUMBING
Air connections shall be provided from the air supply tank to the pump shift control valve and from the pump shift control valve to the frame mounted bracket. The frame mounted bracket shall include labeling identifying the pump and road connection points with threaded 0.25 inch NPT fittings on the solenoid for attaching the customer installed pump. The air supply shall be pressure protected from service brake system.
3109-064

FUEL FILTER/WATER SEPARATOR
The fuel system shall have a Racor GreenMAX 6600R fuel filter/water separator as a primary filter. The fuel filter shall have a drain valve and a see-through cover to allow visual inspection of fuel and filter condition. The Racor 6600R shall meet engine requirements for particulate size, collection capacity, removal efficiency, and water removal efficiency. The filter shall be capable of handling a maximum flow rate of 150 gallons per hour.

A secondary fuel filter shall be included as approved by the engine manufacturer.

An instrument panel lamp and audible alarm which indicates when water is present in the fuel-water separator shall also be included.
3111-002

FUEL LINES
The fuel system supply and return lines installed from the fuel tank to the engine shall be black textile braided lines which are reinforced with braided high tensile steel wire. The fuel lines shall be connected with reusable steel fittings.
3103-008

ELECTRIC FUEL PRIMER
Integral to the engine assembly is an electric lift pump that serves the purpose of pre-filter fuel priming. 3112-013

FUEL COOLER
An aluminum cross flow air to fuel cooler shall be provided to lower fuel temperature allowing the vehicle to operate at higher ambient temperatures. The fuel cooler shall be located behind the rear axle. 3101-102

FUEL TANK
The fuel tank shall have a capacity of sixty-eight (68) gallons and shall measure 35.00 inches in width X

17.00 inches in height X 29.00 inches in length.

The baffled tank shall have a vent port to facilitate venting to the top of the fill neck for rapid filling without "blow-back" and a roll over ball check vent for temperature related fuel expansion and draw.

The tank is designed with dual draw tubes and sender flanges. The tank shall have 2.00 inch NPT fill ports for right or left hand fill. A 0.50 inch NPT drain plug shall be centered in the bottom of the tank.

The fuel tank shall be mounted below the frame, behind the rear axle. Two (2) three-piece strap hanger assemblies with “U” straps bolted midway on the fuel tank front and rear shall be utilized to allow the tank to be easily lowered and removed for service purposes. Rubber isolating pads shall be provided between the tank and the upper tank mounting brackets. Strap mounting studs through the rail, hidden behind the body shall not be acceptable.
3130-001

FUEL TANK MATERIAL AND FINISH
The fuel tank shall be constructed of 12 gauge aluminized steel. The exterior of the tank shall be powder coated black and then painted to match the frame components.

All powder coatings, primers and paint shall be compatible with all metals, pretreatments and primers used. The cross hatch adhesion test per ASTM D3359 Method B, results to be 5B minimum. The pencil hardness test per ASTM D3363 shall have a final post-curved pencil hardness of H-2H. The direct impact resistance test per ASTM D2794, results to be 5B minimum.

Any proposals offering painted fuel tanks with variations from the above process shall not be accepted.

The film thickness of vendor supplied parts shall also be sufficient to meet the performance standards as stated above.
3131-001

FUEL TANK STRAP MATERIAL
The fuel tank straps shall be constructed of ASTM A-36 steel. The fuel tank straps shall be powder coated black and then painted to match the frame components if possible. 3132-011

FUEL TANK MISCELLANEOUS OPTIONS
The fuel tank shall be temporarily mounted, to be permanently relocated by the OEM. The tank and mounting straps as specified shall be included with the chassis along with components for permanent standard installation.
3102-016

FUEL TANK FILL PORT
The fuel tank fill ports shall be provided with two (2) left fill ports located one (1) in the forward position and one (1) in the middle position and the right fill port located in the middle position of the fuel tank.
3114-006

FUEL TANK SERVICEABILTY PROVISIONS
The chassis fuel lines and sender wiring shall have additional length provided so the tank can be easily lowered and removed for service purposes. The additional 12.00 feet of length shall be located above the fuel tank and shall be coiled and secured. The fuel line fittings shall be pointed towards the right side (curbside) of the chassis.
3115-002

FUEL TANK DRAIN PLUG
A 0.5 inch NPT magnetic drain plug shall be centered in the bottom of the fuel tank. 2401-022

FRONT AXLE
The front axle shall be a Meritor Easy Steer Non drive front axle, model number MFS-20. The axle shall include a 3.74 inch drop and a 71.00 inch king pin intersection (KPI). The axle shall include a conventional style hub with a standard knuckle. The weight capacity for the axle shall be rated to 23,000 pounds. This rating shall require special approvals from the wheel manufacturers. 2405-001

FRONT WHEEL BEARING LUBRICATION
The front axle wheel bearings shall be lubricated with oil. The oil level can be visually checked via clear inspection windows in the front axle hubs.
2502-002

FRONT SHOCK ABSORBERS
Two (2) Bilstein inert, nitrogen gas filled shock absorbers shall be provided and installed as part of the front suspension system. The shocks shall be a monotubular design and fabricated using a special extrusion method, utilizing a single blank of steel without a welded seam, achieving an extremely tight peak-to-valley tolerance and maintains consistent wall thickness. The monotubular design shall provide superior strength while maximizing heat dissipation and shock life.

The ride afforded through the use of a gas shock is more consistent and shall not deteriorate with heat, the same way a conventional oil filled hydraulic shock would.

The Bilstein front shocks shall include a digressive working piston assembly allowing independent tuning of the compression and rebound damping forces to provide optimum ride and comfort without compromise. The working piston design shall feature fewer parts than most conventional twin tube and “road sensing” shock designs and shall contribute to the durability and long life of the Bilstein shock absorbers.

Proposals offering the use of conventional twin tube or “road sensing” designed shocks shall not be considered.
2501-018

FRONT SUSPENSION
The front suspension shall include an eleven (11) leaf spring pack in which the longest leaf measures

53.38 inch long and 4.00 inches wide. The springs shall be shot peened for long life and include a military double wrapped front eye. The springs shall be bolted in place with M20 10.9 bolts and have replaceable polyurethane bushings in the spring eyes. The spring capacity shall be rated at 23,000 pounds.
2601-006

STEERING COLUMN/ WHEEL
The cab shall include a Douglas Autotech steering column which shall include a seven (7) position tilt, a

2.25 inch telescopic adjustment, and an 18.00 inch, four (4) spoke steering wheel located at the driver’s position. The steering wheel shall be covered with black polyurethane foam padding.

The steering column shall contain a horn button, self-canceling turn signal switch, four-way hazard switch and headlamp dimmer switch.
2609-002

ELECTRONIC POWER STEERING FLUID LEVEL INDICATOR
The power steering fluid shall be monitored electronically and shall send a signal to activate an audible alarm and visual warning in the instrument panel when fluid level falls below normal. 2603-011

POWER STEERING PUMP
The hydraulic power steering pump shall be a TRW PS and shall be gear driven from the engine. The pump shall be a balanced, positive displacement, sliding vane type. The power steering system shall include an oil to air passive cooler.
2606-009

FRONT AXLE CRAMP ANGLE
The chassis shall have a front axle cramp angle of 48-degrees to the left and 44-degrees to the right. 2610-005

POWER STEERING GEAR
The power steering gear shall be a TRW model TAS 85 with an assist cylinder. 2608-001

CHASSIS ALIGNMENT
The chassis frame rails shall be measured to insure the length is correct and cross checked to make sure they run parallel and are square to each other. The front and rear axles shall be laser aligned. The front tires and wheels shall be aligned and toe-in set on the front tires by the chassis manufacturer. 3401-012

REAR AXLE
The rear axle shall be a Meritor model RT-52-185 tandem drive axle. The axle shall include precision forged, single reduction differential gearing, and shall have a fire service rated capacity of 54,000 pounds.

The axle shall be built of superior construction and quality components to provide the rugged dependability needed to stand up to the fire industry’s demands. The axle shall include rectangular shaped, hot-formed housing with a standard wall thickness of 0.56 of an inch for extra strength and rigidity and a rigid differential case for high axle strength and reduced maintenance.

The axle shall have heavy-duty Hypoid gearing for longer life, greater strength and quieter operation.

Industry-standard wheel ends for compatibility with both disc and drum brakes, and unitized oil seal technology to keep lubricant in and help prevent contaminant damage will be used. 3403-001

REAR AXLE DIFFERENTIAL LUBRICATION
The rear axle differential shall be lubricated with oil. 3411-001

REAR WHEEL BEARING LUBRICATION
The rear axle wheel bearings shall be lubricated with oil. 3407-003

REAR AXLE DIFFERENTIAL CONTROL
The tandem axle chassis shall include an inter-axle differential lock, which shall allow both axles to be engaged as drive axles. The inter-axle differential lock shall be controlled by a locking rocker switch on the switch panel. The light on the switch shall illuminate with positive engagement of the inter-axle differential lock.
3408-003

VEHICLE TOP SPEED
The top speed of the vehicle shall be approximately 60 MPH +/-2 MPH at governed engine RPM. 3501-035

REAR SUSPENSION
The tandem rear axle shall feature a Hendrickson Firemaax™ air suspension. Each axle will be independently suspended for optimum performance. The suspension shall include four optimized air springs mounted to cast structural trailing arms, transverse cross beams for increased roll stability and four heavy duty shock absorbers. Dual air height control valves shall be installed on each axle to ensure equal frame height on both sides of the vehicle regardless of the load. Axle alignment is maintained using four eccentric bushings at each frame bracket. The rear tandem suspension shall have 54.00 inch axle centers.

The rear suspension capacity shall be rated at 48,001 to 54,000 pounds 3503-003

REAR SHOCK ABSORBERS
Shock absorbers shall be supplied by the suspension manufacturer and installed on the rear axle suspension.
3625-002

TIRE INTERMITTENT SERVICE RATING
The chassis shall be rated using Intermittent Service ratings provided to the emergency vehicle market by the tire manufacturers as the basis for determining the maximum vehicle load and speed. 3601-063

FRONT TIRE
The front tires shall be Michelin 425/65R-22.5 20PR "L" tubeless radial XZY3 mixed service tread.

The front tire stamped load capacity shall be 22,800 pounds per axle with a nominal speed rating of 65 miles per hour when properly inflated to 120 pounds per square inch.

The Michelin Intermittent Service Rating maximum load capacity shall be 24,396 pounds per axle with a maximum speed of 65 miles per hour when properly inflated to 120 pounds per square inch.

The Michelin Intermittent Service Rating maximum speed capacity shall be 22,800 pounds per axle with a speed rating of 75 miles per hour when properly inflated to 120 pounds per square inch.

The Michelin Intermittent Service Rating limits the operation of the emergency vehicle to no more than fifty (50) miles of continuous operation under maximum recommended payload, or without stopping for at least twenty (20) minutes. The emergency vehicle must reduce its speed to no more than 50 MPH after the first fifty (50) miles of travel.
3602-010

REAR TIRE
The rear tires shall be Michelin 12R-22.5 16PR "H" tubeless radial XZE regional tread.

The rear tire stamped load capacity shall be 27,120 pounds per axle with a speed rating of 75 miles per hour when properly inflated to 120 pounds per square inch.

The Michelin Tire Intermittent Service Rating load capacity shall be 28,880 pounds per axle with a speed rating of 75 miles per hour when properly inflated to 120 pounds per square inch. The Michelin Intermittent Service Rating limits the operation of the emergency vehicle to one (1) hour of loaded travel with a one (1) hour cool down prior to another loaded run. 3413-538

REAR AXLE RATIO
The rear axle ratio shall be 5.38:1.
3614-030

TIRE PRESSURE INDICATOR
There shall be electronic chrome LED valve caps shipped loose for installation by the OEM which shall illuminate with a red LED when tire pressure drops 8psi provided. The valve caps are self-calibrating and set to the pressure of the tire upon installation.
3701-034

FRONT WHEEL
The front wheels shall be Alcoa hub piloted, 22.50 inch X 12.25 inch aluminum wheels. The outer face of the wheels shall feature Alcoa’s Dura-Bright® finish as an integral part of the wheel surface. Alcoa Dura-Bright® wheels keep their shine without polishing. Brake dust, grime and road debris are easily removed by simply cleaning the wheels with soap and water. The hub piloted mounting system shall provide easy installation and shall include two-piece flange nuts. 3703-062

REAR WHEEL
The rear wheels shall be Alcoa hub piloted, 22.50 inch X 8.25 inch aluminum wheels with a polished outer surface and Alcoa Dura-Bright® wheel treatment as an integral part of the wheel surface. The inner rear wheels shall be Alcoa hub piloted, 22.50 inch X 8.25 inch aluminum wheels with a bright machine finish. The hub piloted mounting system shall provide easy installation and shall include twopiece flange nuts. 3702-018

WHEEL TRIM
The front wheels shall include two (2) sets of stainless steel lug nut covers and stainless steel baby moons shipped loose with the chassis for installation by the apparatus builder. The baby moons shall have cutouts for oil seal viewing when applicable.

The rear wheels shall include two (2) sets of stainless steel lug nut covers and band mounted spring clip stainless steel high hats shipped loose with the chassis for installation by the apparatus builder.

The lug nut covers, baby moons, and high hats shall be RealWheels® brand constructed of 304L grade, non-corrosive stainless steel with a mirror finish. Each wheel trim component shall meet D.O.T. certification.
3205-015

BRAKE SYSTEM
A rapid build-up air brake system shall be provided. The air brakes shall include, at a minimum, a three (3) air tank, four (4) reservoir system with a total of 6236 cubic inch of air capacity. A floor mounted treadle valve shall be mounted inside the cab for graduated control of applying and releasing the brakes.

An inversion valve shall be installed to provide a service brake application in the unlikely event of primary air supply loss. All air reservoirs provided on the chassis shall be labeled for identification.

The tandem rear axle spring brakes shall automatically apply in any situation when the air pressure falls below 25 PSI and shall include a mechanical means for releasing the spring brakes when necessary. An audible alarm shall designate when the system air pressure is below 60 PSI.

A six (6) sensor, six (6) modulator Anti-lock Braking System (ABS) shall be installed on the front and tandem rear axles in order to prevent the brakes from locking or skidding while braking during hard stops or on icy or wet surfaces. This in turn shall allow the driver to maintain steering control under heavy braking and in most instances, shorten the braking distance. The electronic monitoring system shall incorporate diagonal circuitry which shall monitor wheel speed during braking through a sensor and tone ring on each wheel. A dash mounted ABS lamp shall be provided to notify the driver of a system malfunction. The ABS system shall automatically disengage the auxiliary braking system device when required. The speedometer screen shall be capable of reporting all active defaults using PID/SID and FMI standards.

Additional safety shall be accommodated through Automatic Traction Control (ATC) which shall be installed on the tandem rear axle. The ATC system shall apply the ABS when the drive wheels loose traction. The system shall scale the electronic engine throttle back to prevent wheel spin while accelerating on ice or wet surfaces.

A virtual style switch shall be provided and properly labeled “mud/snow”. When the switch is pressed once, the system shall allow a momentary wheel slip to obtain traction under extreme mud and snow conditions. During this condition the ATC light shall blink continuously notifying the driver of activation. Pressing the switch again shall deactivate the mud/snow feature.

The Electronic Stability Control (ESC) unit is a functional extension of the electronic braking system. It is able to detect any skidding of the vehicle about its vertical axis as well as any rollover tendency. The control unit comprises an angular-speed sensor that measures the vehicle’s motion about the vertical axis, caused, for instance, by cornering or by skidding on a slippery road surface. An acceleration sensor measures the vehicle’s lateral acceleration. The Controller Area Network (CAN) bus provides information on the steering angle. On the basis of lateral acceleration and steering angle, an integrated microcontroller calculates a theoretical angular speed for the stable vehicle condition. 3206-003

FRONT BRAKES
The front brakes shall be Meritor EX225 Disc Plus disc brakes with 17.00 inch vented rotors. 3207-005

REAR BRAKES
The rear brakes shall be Meritor 16.50 inch X 7.00 inch S-cam drum type. The brakes shall feature a cast iron shoe.
3208-001

PARK BRAKE
Upon application of the push-pull valve in the cab, the rear brakes will engage via mechanical spring force. This is accomplished by dual chamber rear brakes, satisfying the FMVSS parking brake requirements.
3219-002

SUPPLEMENTAL BRAKE
A supplemental brake engagement shall be supplied that can only be engaged while the rear spring brakes are engaged. In addition to the mechanical rear brake engagement, the front service brakes shall also be engaged via air pressure, providing additional braking capability. Front service brake activation shall be accomplished with activation of the rear mechanical park brake valve. 3204-029

PARK BRAKE CONTROL
A Meritor-Wabco manual hand control push-pull style valve shall operate the parking brake.

The parking brake actuation valve shall be mounted to the left side of the engine tunnel integrated into the transmission shift pod console within easy access of the driver. 3214-002

REAR BRAKE SLACK ADJUSTERS
Haldex rear brake automatic slack adjusters shall be installed on the axle. 3202-001

AIR DRYER
The brake system shall include a Wabco System Saver 1200 air dryer with an integral 100 watt heater with a Metri-Pack sealed connector. The air dryer incorporates an internal turbo cutoff valve that closes the path between the air compressor and air dryer purge valve during the compressor "unload" cycle. The turbo cutoff valve allows purging of moisture and contaminants without the loss of turbo boost pressure.

The air dryer shall be located on the right hand frame rail forward of the front wheel behind the right hand cab step.
3215-004

FRONT BRAKE CHAMBERS
The front brakes shall be provided with MGM type 24 long stroke brake chambers. 3210-015

REAR BRAKE CHAMBERS
The rear axle shall include TSE 30/36 brake chambers which shall convert the energy of compressed air into mechanical force and motion. This shall actuate the brake camshaft, which in turn shall operate the foundational brake mechanism forcing the brake shoes against the brake drum. The TSE Type 36 brake chamber has a 36.00 square inch effective area.
3320-001

AIR COMPRESSOR
The air compressor provided for the engine shall be a Wabco® SS318 single cylinder pass-through drive type compressor which shall be capable of producing 18.7 CFM at 1200 engine RPMs. The air compressor shall feature a higher delivery efficiency translating to more air delivery per horsepower absorbed. The compressor shall include an aluminum cylinder head which shall improve cooling, reduce weight and decrease carbon formation. Superior piston and bore finishing technology shall reduce oil consumption and significantly increasing the system component life. 3339-004

AIR GOVERNOR
An air governor shall be provided to control the cut-in and cut-out pressures of the engine mounted air compressor. The governor shall be calibrated to meet FMVSS requirements. The air governor shall be located on the air dryer bracket.
3303-002

MOISTURE EJECTORS
Manual cable actuated drain valves shall be installed on all reservoirs of the air supply system. The actuation pull cables shall be coiled and tied at each drain valve. The supplied cables when extended shall be sufficient in length to allow each drain to be activated from the side of the apparatus. 3307-001

AIR SUPPLY LINES
The air system on the chassis shall be plumbed with color coded reinforced nylon tubing air lines. The primary (rear) brake line shall be green, the secondary (front) brake line red, the parking brake line orange and the auxiliary (outlet) will be blue.

Brass compression type fittings shall be used on the nylon tubing. All drop hoses shall include fiber reinforced neoprene covered hoses.
3338-002

REAR AIR TANK MOUNTING
If a combination of wheel base, air tank quantity, or other requirements necessitate the location of one or more air tanks to be mounted rear of the fuel tank, these tank(s) will be mounted perpendicular to frame. 2103-2280

WHEELBASE
The chassis wheelbase shall be 228.00 inches.
2106-0640

REAR OVERHANG
The chassis rear overhang shall be 64.00 inches.
2101-002
FRAME
The frame shall consist of double rails running parallel to each other with cross members forming a ladder style frame. The frame rails shall be formed in the shape of a "C" channel, with the outer rail measuring 10.25 inches high X 3.50 inches deep upper and lower flanges X 0.38 inches thick with an inner channel of 9.44 inches high X 3.13 inches deep and 0.38 inches thick. Each rail shall be constructed of 110,000 psi minimum yield high strength low alloy steel. Each double rail section shall be rated by a Resistance Bending Moment (RBM) minimum of 3,213,100 inch pounds and have a minimum section modulus of 29.21 cubic inches. The frame shall measure 35.00 inches in width.

Proposals calculating the frame strength using the “box method” shall not be considered.

Proposals including heat treated rails shall not be considered. Heat treating frame rails produces rails that are not uniform in their mechanical properties throughout the length of the rail. Rails made of high strength, low alloy steel are already at the required yield strength prior to forming the rail.

A minimum of seven (7) fully gusseted 0.25 inch thick cross members shall be installed. The inclusion of the body mounting, or bumper mounting shall not be considered as a cross member. The cross members shall be attached using zinc coated grade 8 fasteners. The bolt heads shall be flanged type, held in place by distorted thread flanged lock nuts. Each cross member shall be mounted to the frame rails utilizing a minimum of 0.25 inch thick gusset reinforcement plates at all corners balancing the area of force throughout the entire frame.
.

Any proposals not including additional reinforcement for each cross member shall not be considered.

All relief areas shall be cut in with a minimum 2.00 inch radius at intersection points with the edges ground to a smooth finish to prevent a stress concentration point. 2111-136

MISCELLANEOUS FRAME OPTIONS
The frame shall include drillings which shall be specific to mounting a Smeal 105RM, 100RM, 125RM, or 100MM substructure.

See PDF for OEM Specified pattern.
2117-004

FRAME CLEAR AREA
The chassis frame shall be left clear of chassis mounted components inside or outside the frame rails within the first 30.00 inches behind the cab to allow space for OEM installed components. Cross members may be installed in the clear area if required for proper frame or driveline configuration. 2110-101

FRAME PAINT
The frame shall be powder coated black prior to any attachment of components.

All powder coatings, primers and paint shall be compatible with all metals, pretreatments and primers used. The cross hatch adhesion test per ASTM D3359 shall not have a fail of more than ten (10) squares. The pencil hardness test per ASTM D3363 shall have a final post-curved pencil hardness of H2H. The direct impact resistance test per ASTM D2794 shall have an impact resistance of 120.00 inches per pound at 2 mils.

Any proposals offering painted frame with variations from the above process shall not be accepted. The film thickness of vendor supplied parts shall also be sufficient to meet the performance standards as stated above.
8007-036

FRAME ASSEMBLY STRUCTURAL
Purchaser shall receive a Frame Assembly Structural Fifty (50) Years or 250,000 Miles limited warranty in accordance with, and subject to, warranty certificate RFW0305. The warranty certificate is incorporated by reference into this proposal, and included with this proposal or available upon request. 8019-002

FRAME RAIL CORROSION
Purchaser shall receive a Frame Rail Corrosion (Powder Coat) Three (3) Years or 48,000 Miles limited warranty in accordance with, and subject to, warranty certificate RFW0311. The warranty certificate is incorporated by reference into this proposal, and included with this proposal or available upon request. 8022-004

FRAME COMPONENTS CORROSION
Purchaser shall receive a Frame Components Corrosion (Powder Coat) Three (3) Years or 48,000 Miles limited warranty in accordance with, and subject to, warranty certificate RFW0313. The warranty certificate is incorporated by reference into this proposal, and included with this proposal or available upon request.
2201-006

FRONT BUMPER
The chassis shall include a special approach style steel front bumper. The bumper shall be constructed of

0.19 inch thick ASTM A-36 formed steel which shall be painted. The bumper shall be 102.63 inches in width with angled corners. The bottom flange of the bumper shall be designed with a 20-degree angle to allow for an increased angle of approach for the vehicle. 2202-024

FRONT BUMPER EXTENSION LENGTH
The front bumper shall be extended approximately 12.50 inches ahead of the cab. The bumper extensions for bumper mounting shall include an angled bottom and designed for a 7.34 inches tall bumper face. Extensions shall be designed to mount to a standard front frame section. 2206-001

FRONT BUMPER PAINT
The front bumper shall be painted the same as the lower cab color. 2208-003

FRONT BUMPER APRON
The 12.50 inch extended front bumper shall include an apron constructed of 0.19 inch thick embossed aluminum tread plate.

The apron shall be installed between the bumper and the front face of the cab affixed using stainless steel bolts attaching the apron to the top bumper flange. 2237-004

FRONT BUMPER DISCHARGE
The chassis shall include frame mounted 2.00 inch diameter plumbed pipe intended for use as a discharge trash line. The discharge pipe shall be routed from the left hand front splay rail area behind the bumper to the area rear of the front axle, ahead of the battery box.

The discharge shall pipe shall be a, 2.00 inch stainless steel schedule 10 tube. The discharge shall include a Victaulic groove for connecting to the pump and discharge hose plumbing on each end of the tube.

The apparatus manufacturer shall plumb the discharge pipe to the pump and shall provide all valves as required.
2211-012

FRONT BUMPER COMPARTMENT CENTER
The front bumper shall include a compartment in the bumper apron located in the center between the frame rails which may be used as a hose well. The compartment shall be constructed of 0.19 thick ASTM A-36 painted steel.
5503-021

MECHANICAL SIREN
The front bumper shall include an electro mechanical Federal Q2B™ siren, which shall be streamlined, chrome-plated and shall produce 123 decibels of sound at 10.00 feet. The Q2B™ siren produces a distinctive warning sound that is recognizable at long distances. A unique clutch design provides a longer coast down sound while reducing the amp draw to 100 amps. The siren shall measure 10.50 inches wide X 10.00 inches high X 14.00 inches deep. The siren shall include mounting hardware designed to recess or flush mount.
2218-049

MECHANICAL SIREN LOCATION
The siren shall be recess mounted on the driver side of the front fascia of the bumper, in the extreme outboard position.
5501-020

AIR HORN
The front bumper shall include two (2) Hadley brand E-Tone air horns which shall measure 21.00 inches long with a 6.00 inch round flare. The air horns shall be trumpet style with a chrome finish on the exterior and a painted finish deep inside the trumpet.
2216-007

AIR HORN LOCATION
The air horns shall be recess mounted in the front bumper face on the right side of the bumper in the inboard and outboard positions relative to the right hand frame rail. 2232-002

AIR HORN RESERVOIR
One (1) air reservoir, with a 1200 cubic inch capacity, shall be installed on the chassis to act as a supply tank for operating air horns. The reservoir shall be isolated with a 90 PSI pressure protection valve on the reservoir supply side to prevent depletion of the air to the air brake system. 5504-060

ELECTRONIC SIREN SPEAKER
There shall be one (1) Federal Signal Inc. Dynamax® model ES100C, 100 watt speaker provided. The speaker shall measure 5.90 inches tall X 5.50 inches wide X 2.30 inches deep. The speaker shall include a Federal Signal “Electric F” style grille which shall measure 6.61 inches tall X 6.78 inches wide. 2217-003

ELECTRONIC SIREN SPEAKER LOCATION
The electronic siren speaker shall be located on the front bumper face on the left side outboard of the frame rail in the inboard position.
2204-006

FRONT BUMPER TOW EYES
The bumper shall include two (2) chrome plated tow eyes shall be installed through the front bumper.

The eyes shall be fabricated from 0.75 inch thick #1020 ASTM-A36 hot rolled steel. The inside diameter of the eye shall be 2.00 inches and include inside/outside chamfered edges. 2301-001

CAB TILT SYSTEM
The entire cab shall be capable of tilting approximately 45-degrees to allow for easy maintenance of the engine and transmission. The cab tilt pump assembly shall be located on the right side of the chassis above the battery box.

The electric-over-hydraulic lift system shall include an ignition interlock and red cab lock down indicator lamp on the tilt control which shall illuminate when holding the “Down” button to indicate safe road operation.

It shall be necessary to activate the master battery switch and set the parking brake in order to tilt the cab. As a third precaution the ignition switch must be turned off to complete the cab tilt interlock safety circuit.

Two (2) spring-loaded hydraulic hold down hooks located outboard of the frame shall be installed to hold the cab securely to the frame. Once the hold-down hooks are set in place, it shall take the application of pressure from the hydraulic cab tilt lift pump to release the hooks.

Two (2) cab tilt cylinders shall be provided with velocity fuses in each cylinder port. The cab tilt pivots shall be 1.90 inch ball and be anchored to frame brackets with 1.25 inch diameter studs.

A steel safety channel assembly, painted safety yellow shall be installed on the right side cab lift cylinder to prevent accidental cab lowering. The safety channel assembly shall fall over the lift cylinder when the cab is in the fully tilted position. A cable release system shall also be provided to retract the safety channel assembly from the lift cylinder to allow the lowering of the cab. 2302-005

CAB TILT AUXILIARY PUMP
A manual cab tilt pump module shall be attached to the cab tilt pump housing. 2303-003

CAB TILT LIMIT SWITCH
A cab tilt limit switch shall be installed. The switch will effectively limit the travel of the cab when being tilted. The limit adjustment of the switch shall be preset by the chassis manufacturer to prevent damage to the cab or any bumper mounted option mounted in the cab tilt arc. Further adjustment to the limit by the apparatus manufacturer shall be available to accommodate additional equipment. 2305-001

CAB TILT CONTROL RECEPTACLE
The cab tilt control cable shall include a receptacle which shall be temporarily located on the right hand chassis rail rear of the cab to provide a place to plug in the cab tilt remote control pendant. The tilt pump shall include 8.00 feet of cable with a six (6) pin Deutsch receptacle with a cap.

The remote control pendant shall include 20.00 feet of cable with a mating Deutsch connector. The remote control pendant shall be shipped loose with the chassis. 2306-002

CAB TILT LOCK DOWN INDICATOR
The cab dash shall include a message located within the dual air pressure gauge which shall alert the driver when the cab is unlocked and ajar. The alert message shall cease to be displayed when the cab is in the fully lowered position and the hold down hooks are secured and locked to the cab mounts.

In addition to the alert message an audible alarm shall sound when the cab is unlocked and ajar and the parking brake is released.
1401-009

CAB WINDSHIELD
The cab windshield shall have a surface area of 2969.88 square inches and be of a two (2) piece wraparound design for maximum visibility.

The glass utilized for the windshield shall include standard automotive tint. The left and right windshield shall be fully interchangeable thereby minimizing stocking and replacement costs.

Each windshield shall be installed using black self locking window rubber. 1402-005

GLASS FRONT DOOR
The front cab doors shall include a window which is 27.00 inches in width X 26.00 inches in height.

These windows shall have the capability to roll down completely into the door housing. This shall be accomplished manually utilizing a crank style handle on the inside of the door. A reinforced window regulator assembly shall be provided for severe duty use.

There shall be an irregular shaped fixed window which shall measure 2.50 inches wide at the top, 8.00 inches wide at the bottom X 26.00 inches in height, more commonly known as “cozy glass” ahead of the front door roll down windows.

The windows shall be mounted within the frame of the front doors trimmed with a black anodized ring on the exterior.
1407-001

GLASS TINT FRONT DOOR
The windows located in the left and right front doors shall have a standard green automotive tint which shall allow seventy-five percent (75%) light transmittance. 1419-012

GLASS REAR DOOR RH
The rear right hand side door shall include a window which is 27.00 inches in width X 26.00 inches in height. This window shall roll up and down manually utilizing a crank style handle on the inside of the door. A reinforced window regulator assembly shall be provided for severe duty use. 1430-001

GLASS TINT REAR DOOR RIGHT HAND
The window located in the right hand side rear door shall include a standard green automotive tint which shall allow seventy-five percent (75%) light transmittance. 1412-013

GLASS REAR DOOR LH
The rear left hand side door shall include a window which is 27.00 inches in width X 26.00 inches in height. This window shall roll up and down manually utilizing a crank style handle on the inside of the door. A reinforced window regulator assembly shall be provided for severe duty use. 1431-001

GLASS TINT REAR DOOR LEFT HAND
The window located in the left hand side rear door shall include a standard green automotive tint which shall allow seventy-five percent (75%) light transmittance. 1410-010

GLASS SIDE MID RH
The cab shall include a window on the right side behind the front and ahead of the crew doors which shall measure 16.00 inches wide X 12.00 inches high. This window shall be fixed within this space and shall be rectangular in shape. The window shall be mounted using self-locking window rubber. The glass utilized for this window shall include a green automotive tint unless otherwise noted. 1432-001

GLASS TINT SIDE MID RIGHT HAND
The window located on the right hand side of the cab between the front and rear doors shall include a standard green automotive tint which shall allow seventy-five percent (75%) light transmittance. 1409-010

GLASS SIDE MID LH
The cab shall include a window on the left side behind the front door and ahead of the crew door and above the wheel well which shall measure 16.00 inches wide X 12.00 inches high. This window shall be fixed within this space and shall be rectangular in shape. The window shall be mounted using selflocking window rubber. The glass utilized for this window shall include a green automotive tint unless otherwise noted.
1433-001

GLASS TINT SIDE MID LEFT HAND
The window located on the left hand side of the cab between the front and rear doors shall include a standard green automotive tint which shall allow seventy-five percent (75%) light transmittance. 1614-115

CLIMATE CONTROL
The cab shall include a front under dash heater/defroster.

The cab shall also include a combination heater air-conditioning unit mounted on the engine tunnel. This unit shall offer eight (8) adjustable louvers, four (4) forward facing and four (4) rearward facing, a temperature control valve and two (2) blowers offering three (3) speeds which shall be capable of circulating 550 cubic feet of air per minute. The unit shall be rated for 42,500 BTU/Hr of cooling and 36,000 BTU/Hr of heating.

All defrost/heating systems shall be plumbed with one (1) seasonal shut-off valve at the front corner on the right side of the cab.

The air conditioner lines shall be a mixture of custom bend zinc coated steel fittings and Aeroquip flexible hose with Aeroquip EZ clip fittings.
1632-002

CLIMATE CONTROL DRAIN
The climate control system shall include a gravity drain for water management. The gravity drain shall remove condensation from the air conditioning system without additional mechanical assistance. 1617-113

CLIMATE CONTROL ACTIVATION
The defrosting controls shall be located on the lower left portion of the center dash panel, within easy reach of the driver. There shall be additional heating and air conditioning controls located on the engine tunnel mounted climate control unit.
1603-002

A/C CONDENSER LOCATION
A roof mounted A/C condenser shall be installed on the left side of the cab, mid-roof. 1601-001

A/C COMPRESSOR
The air-conditioning compressor shall be a belt driven, engine mounted, open type compressor that shall be capable of producing a minimum of 32,000 BTU at 1500 engine RPMs. The compressor shall utilize R-134A refrigerant and PAG oil.
1530-103

UNDER CAB INSULATION
The underside of the cab tunnel surrounding the engine shall be lined with multi-layer insulation, engineered for application inside diesel engine compartments.

The insulation shall act as a noise barrier, absorbing noise thus keeping the decibel level in the cab well within NFPA recommendations. As an additional benefit, the insulation shall assist in sustaining the desired temperature within the cab interior.

The engine tunnel insulation shall measure approximately 0.30 inch thick including a multi-layer foil faced glass cloth and polyester fiber layer. The foil surface acts as protection against heat, moisture and other contaminants. The insulation shall meet or exceed FMVSS 302 flammability test.

The insulation shall be cut precisely to fit each section and sealed for additional heat and sound deflection. The insulation shall be held in place by acrylic pressure sensitive adhesive. In addition, the insulation shall have a removable aluminum overlay installed to protect the insulation and assist in retaining the insulation tight against the engine tunnel surfaces. 1327-001

INTERIOR TRIM FLOOR
The floor of the cab shall be covered with a multi-layer mat consisting of 0.25 inch thick sound absorbing closed cell foam with a 0.06 inch thick non-slip vinyl surface with a pebble grain finish. The covering shall be held in place by a pressure sensitive adhesive and aluminum trim molding. All exposed seams shall be sealed with silicone caulk matching the color of the floor mat to reduce the chance of moisture and debris retention.
1302-001

INTERIOR TRIM
The cab interior shall include trim on the front ceiling, rear crew ceiling, and the cab walls. It shall be easily removable to assist in maintenance. The trim shall be constructed of insulated vinyl over a hard board backing.
1368-002

REAR WALL INTERIOR TRIM
The rear wall of the cab shall be trimmed with vinyl.
1306-006

HEADER TRIM
The cab interior shall feature header trim over the driver and officer dash constructed of 5052-H32 Marine Grade, 0.13 inch thick aluminum.
1305-020

TRIM CENTER DASH
The main center dash area shall be constructed of 5052-H32 Marine Grade, 0.13 inch thick aluminum plate and include provisions for the front under dash heater defroster. There shall be four (4) holes located on the top of the dash near each outer edge of the electrical access cover for ventilation. 1339-104

TRIM LH DASH
The left hand dash shall be constructed of 5052-H32 Marine Grade, 0.13 inch thick aluminum plate for a perfect fit around the instrument panel. For increased occupant protection the extreme duty left hand dash utilizes patent pending break away technology to reduce rigidity in the event of a frontal crash. The left hand dash shall offer lower vertical surface area to the left and right of the steering column to accommodate control panels. The left hand dash shall also include provisions for the front under dash heater defroster.
1321-021

TRIM RH DASH
The right hand dash trim shall be constructed of 5052-H32 Marine Grade, 0.13 of an inch thick aluminum plate and shall include provisions for the front under dash heater defroster. 1307-002

ENGINE TUNNEL TRIM
The cab engine tunnel shall be covered with a multi-layer mat consisting of 0.25 inch closed cell foam with a 0.06 inch thick non-slip vinyl surface with a pebble grain finish. The mat shall be held in place by pressure sensitive adhesive. The engine tunnel mat shall be trimmed with anodized aluminum stair nosing trim for an aesthetically pleasing appearance.
5040-116

POWER POINT DASH MOUNT
The cab shall include four (4) 12 volt cigarette lighter type receptacles in the cab dash to provide a power source for 12 volt electrical equipment. The cab shall also include two (2) universal serial bus (USB) charging receptacles in the cab dash to provide a power source for USB chargeable electrical equipment.

Each USB port shall be capable of a 12 watt, 2.4 amp fast charge output. The receptacles shall be wired battery direct.
1303-038

STEP TRIM
Each cab entry door shall include a three step entry. The first step closest to the ground shall be constructed of SAE 304 stainless steel with embossed perforations and diamond shaped cutout. The perforations and cutouts shall allow water and other debris to flow through rather than becoming trapped within the stepping surface. The step shall feature a splash guard to reduce water and debris from splashing in to the step. The splash guard shall have drainage holes beneath the back of the step to allow debris and water to flow through rather than becoming trapped within the stepping surface. The stainless steel material shall have a number 8 mirror finish. The lower step shall be mounted to a frame which is integral with the construction of the cab for rigidity and strength. The middle step shall be integral with the cab construction and shall be trimmed with a Flex-Tred® adhesive grit surface material. 1379-003

UNDER CAB ACCESS DOOR
The cab shall include an aluminum access door in the left crew step riser painted to match the cab interior paint with a push and turn latch. The under cab access door shall provide access to the diesel exhaust fluid fill.
1102-013

INTERIOR DOOR TRIM
The interior trim on the doors of the cab shall consist of an aluminum panel constructed of Marine Grade 5052-H32 0.13 of an inch thick aluminum plate. The door panels shall include a painted finish. 1323-001

DOOR TRIM CUSTOMER NAMEPLATE
The interior door trim on the front doors shall include a customer nameplate which states the vehicle was custom built for their Department.
1105-001

CAB DOOR TRIM REFLECTIVE
The interior of each door shall include high visibility reflective tape. A white reflective tape shall be provided vertically along the rear outer edge of the door. The lowest portion of each door skin shall include a reflective tape chevron with red and white stripes and a Spartan logo. The chevron tape shall measure 6.00 inches in height.
1308-001
INTERIOR GRAB HANDLE "A" PILLAR
There shall be two (2) rubber covered 11.00 inch grab handles installed inside the cab, one on each “A” post at the left and right door openings. The left handle shall be located 7.88 inches above the bottom of the door window opening and the right handle shall be located 2.88 inches above the bottom of the door window opening. The handles shall assist personnel in entering and exiting the cab. 1332-008

INTERIOR GRAB HANDLE FRONT DOOR
Each front door shall include one (1) ergonomically contoured 9.00 inch cast aluminum handle mounted horizontally on the interior door panels. The handles shall feature a textured black powder coat finish to assist personnel entering and exiting the cab.
1345-002

INTERIOR GRAB HANDLE REAR DOOR
A black powder coated cast aluminum assist handle shall be provided on the inside of each rear crew door. A 30.00 inch long handle shall extend horizontally the width of the window just above the window sill. The handle shall assist personnel in exiting and entering the cab. 1301-003

INTERIOR SOFT TRIM COLOR
The cab interior soft trim surfaces shall be gray in color. 1337-002

INTERIOR TRIM SUN VISOR
The header shall include two (2) 7.00 inches high X 18.00 inches wide impact resistant, transparent acrylic polycarbonate sun visors with a smoke gray tint shall be provided and installed on the header above the driver and officer.

The see thru visors are designed for maximum flexibility of positioning utilizing an arm with virtually unlimited adjustability with 13.50 inch long lateral travel of the tinted visor at the end of the arm which can be locked in place by a thumbscrew.

The visors are easily adjusted and can be placed into a chosen position with one hand. The sun visors will help protect vehicle occupants from solar glare without obscuring their vision. 1304-001

INTERIOR FLOOR MAT COLOR
The cab interior floor mat shall be gray in color.
1335-017

CAB PAINT INTERIOR DOOR TRIM
The inner door panel surfaces shall be painted with multi-tone silver gray texture finish. 1371-017

HEADER TRIM INTERIOR PAINT
The metal surfaces in the header area shall be coated with multi-tone silver gray texture finish. 1370-019

TRIM CENTER DASH INTERIOR PAINT
The entire center dash shall be coated with multi-tone silver gray texture finish. Any accessory pods attached to the dash shall also be painted this color.
1378-018

TRIM LH DASH INTERIOR PAINT
The left hand dash shall be painted with a multi-tone silver gray texture finish. 1373-018

TRIM RIGHT HAND DASH INTERIOR PAINT
The right hand dash shall be painted with multi-tone silver gray texture finish. 1344-002

DASH PANEL GROUP
The main center dash area shall include three (3) removable panels located one (1) to the right of the driver position, one (1) in the center of the dash and one (1) to the left of the officer position. The center panel shall be within comfortable reach of both the driver and officer. 1312-074

SWITCHES CENTER PANEL
The center dash panel shall include eight (8) standard rocker switch positions in the upper left portion of the panel.

A rocker switch with a blank legend installed directly above shall be provided for any position without a switch and legend designated by a specific option. The non-specified switches shall be two-position, black switches with a green indicator light. Each blank switch legend can be custom engraved by the body manufacturer. All switch legends shall have backlighting provided. 1313-007

SWITCHES LEFT PANEL
The left dash panel shall include five (5) switches in a three (3) over two (2) staggered switch configuration. Two (2) rocker switches, one (1) headlight switch, one (1) windshield wiper/washer control switch and one (1) instrument lamp dimmer switch shall be provided.

A rocker switch with a blank legend installed directly above shall be provided for any position not designated by a specific option. The non-designated switches shall be two-position, black switches with a green indicator light. Each blank switch legend can be custom engraved by the body manufacturer. All switch legends shall have backlighting provided.
1314-001

SWITCHES RIGHT PANEL
The right dash panel shall include no rocker switches or legends. 1225-007

SEAT BELT WARNING
A Weldon seat belt warning system, integrated with the Vehicle Data Recorder system, shall be installed for each seat within the cab. The system shall provide a visual warning indicator in the Vista display and control screen(s).

The warning system shall activate when any seat is occupied with a minimum of 60 pounds, the corresponding seat belt remains unfastened, and the park brake is released. The warning system shall also activate when any seat is occupied, the corresponding seat belt was fastened in an incorrect sequence, and the park brake is released. Once activated, the visual indicators and applicable audible alarm shall remain active until all occupied seats have the seat belts fastened. 1237-004

SEAT MATERIAL
The Seats Inc. 911 Battalion and universal seats shall be covered with Turnout Tuff™ rugged material.

Turnout Tuff material is rip-stop weave nylon laminated with a polyurethane backing and is water repellent to 75 PSI to protect seats from being saturated or contaminated by fluids. The material meets FMVSS 302 flammability requirements.
1243-001

SEAT COLOR
All seats supplied with the chassis shall be gray in color. All seats shall include red seat belts. 1249-001

SEAT BACK LOGO
The seat back shall include the “Spartan” logo. The logo shall be centered on the standard headrest of the seat back and on the left side of a split headrest. 1201-021

SEAT DRIVER
The driver's seat shall be a Seats Inc. 911 Battalion series with a ten-way adjustable seat. The seat shall feature six-way electric adjustability up and down, fore and aft with 7.25 inches of travel, and seat rake.

The seat shall also include lumbar and recline manual adjustment.

The seat shall feature an all belts to seat (ABTS) style of safety restraint. The ABTS feature shall include a three-point shoulder harness with the lap belt, automatic retractor and buckle as an integral part of the seat assembly. The buckle portion of the seat belt shall be mounted on a semi-rigid stalk extending from the seat base within easy reach of the occupant.

The minimum vertical dimension from the seat H-point to the ceiling for this belted seating position shall be 35.00 inches measured with the seat height adjusted to the lowest position of travel.

This model of seat shall have successfully completed the static load tests set forth by FMVSS 207/210.

This testing shall include a simultaneous forward load of 3000 pounds each on the lap and shoulder belts and twenty (20) times the weight through the center of gravity. This model of seat installed in the cab model, as specified, shall have successfully completed the dynamic sled testing using FMVSS 208 as a guide with the following accommodations. In order to reflect the larger size outfitted firefighters, the test dummy used shall be a 95th percentile hybrid III male weighing 225 pounds rather than the 50th percentile male dummy weighing 165 pounds as referenced in FMVSS 208.

The materials used in construction of the seat shall also have successfully completed testing with regard to the flammability of materials used in the occupant compartments of motor vehicles as outlined in FMVSS 302, of which dictates the allowable burning rate of materials in the occupant compartments of motor vehicles.
1213-025

SEAT BACK DRIVER
The driver’s seat shall include a standard seat back incorporating the all belts to seat feature (ABTS).

The seat back shall feature a contoured head rest.
1219-001

SEAT MOUNTING DRIVER
The driver’s seat shall be installed in an ergonomic position in relation to the cab dash. 1202-020

SEAT OFFICER
The officer's seat shall be a Seats Inc. 911 Battalion series. The seat shall feature a tapered and padded seat, cushion. The seat shall feature electric six-way adjustable positioning. The six (6) positions shall include up and down and fore and aft. The control shall be located centered under the front of the seat.

The minimum vertical dimension from the seat H-point to the ceiling for this belted seating position shall be 35.00 inches measured with the seat height adjusted to the lowest position of travel.

This model of seat shall have successfully completed the static load tests by FMVSS 207/210. This testing shall include a simultaneous forward load of 3000 pounds each on the lap and shoulder belts and twenty (20) times the weight through the center of gravity. This model of seat installed in the cab model, as specified, shall have successfully completed the dynamic sled testing using FMVSS 208 as a guide with the following accommodations. In order to reflect the larger size outfitted firefighters, the test dummy used shall be a 95th percentile hybrid III male weighing 225 pounds rather than the 50th percentile male dummy weighing 165 pounds as referenced in FMVSS 208. The model of seats shall also have successfully completed the flammability of materials used in the occupant compartments of motor vehicles as outlined in FMVSS 302, of which decides the burning rate of materials in the occupant compartments of motor vehicles.
1214-034

SEAT BACK OFFICER
The officer’s seat back shall include an IMMI brand SmartDock® Gen 2 hands-free self contained breathing apparatus (SCBA) holder. The hands-free holder shall meet NFPA 1901-03 9G dynamic requirements for cylinder restraint systems for use in crew compartments of emergency response vehicles. The bracket shall accommodate and secure most types of self-contained breathing apparatus cylinders.

The hands-free holder shall consist of a back plate, bottom cradle, non-marring top claws, and claw height adjustment knob. The height adjustment knob shall allow for easy adjustment of the claws to the SCBA. The hands-free holder's claws shall lock from inertial forces to prevent the SCBA from becoming a projectile in the event of a crash to meet the NFPA 1901-03 standard for SCBA retention.

The SCBA holder shall offer single-motion insertion into the claws and hands-free release when the SCBA fitted seat occupant rises.

The seat back shall include a removable padded cover which shall be provided over the SCBA cavity. 1220-006

SEAT MOUNTING OFFICER
The officer’s seat shall offer a special mounting position which is 3.00 inches forward of the standard location offering increased room behind the officer seat position. 1297-002

POWER SEAT WIRING
The power seat or seats installed in the cab shall be wired directly to battery power. 1273-001

SEAT BELT ORIENTATION CREW
The crew position seat belts shall follow the standard orientation which extends from the outboard shoulder extending to the inboard hip.
1266-001

SEAT FORWARD FACING CENTER LOCATION
The crew area shall include two (2) forward facing center crew seats with both located at the center of the rear wall.
1206-019

SEAT CREW FORWARD FACING CENTER
The crew area shall include a seat in the forward facing center position which shall be a Seats Inc. 911 Battalion series. The seat shall feature a tapered and padded seat, and cushion. The seat and cushion shall be hinged and compact in design for additional room and shall remain in the stored position until occupied.

The seat shall feature an all belts to seat (ABTS) style of safety restraint. The ABTS feature shall include a three-point shoulder harness with the lap belt and automatic retractor as an integral part of the seat assembly. The buckle portion of the seat belt shall extend from the seat base towards the driver position within easy reach of the occupant.

The minimum vertical dimension from the seat H-point to the ceiling for each belted seating position shall be 35.00 inches.

SEAT BACK FORWARD FACING CENTER
The seat in the forward facing center position shall include a standard seat back. The seat back shall feature an all belts to seat (ABTS) style safety restraint. The ABTS feature shall include a red, threepoint shoulder harness with the lap belt and automatic retractor as an integral part of the seat assembly.

The buckle portion of the seat belt shall extend from the seat base towards the driver position within easy reach of the occupant. The seat back shall feature a contoured, adjustable head rest. 1269-107

SEAT FRAME FORWARD FACING
The forward facing center seating positions shall include an enclosed seat frame located and installed on the rear wall. The seat frame shall measure 42.38 inches wide X 8.63 inches high X 22.00 inches deep.

The seat frame shall be constructed of Marine Grade 5052-H32 0.19 inch thick aluminum plate. The seat box shall be painted with the same color as the remaining interior. 1281-112

SEAT FRAME FORWARD FACING STORAGE ACCESS
There shall be two (2) access points to the storage area one (1) each side of the seat frame. Each access point shall be covered by a hinged door which measures 15.00 inches wide X 6.88 inches high to allow access for storage in the seat box.
1224-002

SEAT MOUNTING FORWARD FACING CENTER
The forward facing center seats shall be installed facing the front of the cab. 1311-101

CAB FRONT UNDERSEAT STORAGE ACCESS
The left and right under seat storage areas shall have a solid aluminum hinged door with non-locking latch.
1355-019

SEAT COMPARTMENT DOOR FINISH
All underseat storage compartment access doors shall have a multi-tone silver gray texture finish. 1511-200

WINDSHIELD WIPER SYSTEM
The cab shall include a triple arm linkage wiper system which shall clear the windshield of water, ice and debris. There shall be two (2) windshield wipers; each shall be affixed to a radial arm. The wiper motor shall be activated by an intermittent wiper control located within easy reach of the driver’s position.
1534-002

ELECTRONIC WINDSHIELD FLUID LEVEL INDICATOR
The windshield washer fluid level shall be monitored electronically. When the washer fluid level becomes low the yellow “Check Message Center” indicator light on the instrument panel shall illuminate and the message center in the dual air pressure gauge shall display a “Check Washer Fluid Level” message.
1103-004

CAB DOOR HARDWARE
The cab entry doors shall be equipped with exterior pull handles, suitable for use while wearing firefighter gloves. The handles shall be made of aluminum with a chrome plated finish.

The interior exit door handles shall be flush paddle type with a black finish, which are incorporated into the upper door panel.

All cab entry doors shall include locks which are keyed alike. The door locks shall be designed to prevent accidental lockout.

The exterior pull handles shall include a scuff plate behind the handle constructed of polished stainless steel to help protect the cab finish.
1111-004

DOOR LOCKS
The cab entry doors shall include a Controller Area Network (CAN) based electronic door lock system which shall include two (2) external keypads, one (1) located on the left side next to the front grab handle and one (1) on the right side next to the front grab handle. There shall be one (1) red rocker switch provided on the inside of each front cab entry door to actuate the cab door locks. Each door lock may also be manually actuated from the inside of the cab by means of a red knob located on the paddle handle of the respective door. The electronic door lock system shall include four (4) key fobs for actuation with buttons for cab entry door locks and for compartment door locks.

When the doors are unlocked using the external keypad or the key fobs the interior dome lights shall illuminate and remain on for a period of twenty (20) seconds. The interior dome safety feature shall require the interior lighting power to be battery direct.

Wiring shall also be provided for up to four (4) exterior cab compartments and up to four (4) body compartments.
1113-003

DOOR LOCK LH EMS COMPARTMENT
The left hand side EMS compartment shall feature a power door lock actuator. 1114-003

DOOR LOCK RH EMS COMPARTMENT
The right hand side EMS compartment shall feature a power door lock actuator. 1112-003

POWER DOOR LOCK COMPARTMENT ACTIVATION
The power door lock feature shall include activation for exterior compartment door locks through the key fob, keypads and through a virtual switch on the multiplex display. 1503-200

GRAB HANDLES
The cab shall include one (1) 18.00 inch knurled, anti-slip, one-piece exterior assist handle behind each cab door. The grab handle shall be made of SAE 304 stainless steel and be 1.25 inch diameter to enable non-slip assistance with a gloved hand.
1504-039

REARVIEW MIRRORS
Ramco model CRM-310-1750-CHCHR bus style mirrors shall be provided. The mirror heads shall be injection molded chrome plated ABS plastic and shall measure 9.50 inches wide X 17.50 inches high.

The mirrors shall be mounted one (1) on each the driver and officer doors of the cab with polished diecast aluminum arms.

The mirrors shall feature an upper heated remote controlled flat glass and a lower heated manually adjustable convex glass. The mirror control switches shall be located within easy reach of the driver. The mirrors shall be manufactured using the finest quality non-glare glass and shall feature a rigid mounting thereby reducing vibration. The mirrors shall be corrosion free under all weather conditions. 1529-003

REARVIEW MIRROR HEAT SWITCH
The heat for the rearview mirrors shall be controlled through a virtual button on the Vista display and control screen.
1513-010

CAB FENDER
Full width wheel well liners shall be installed on the extruded cab to limit road splash and enable easier cleaning. Each two-piece liner shall consist of an inner liner 16.00 inches wide made of vacuum formed ABS composite and an outer fenderette 5.00 inches wide made of polished aluminum. 1514-002

MUD FLAPS FRONT
The front wheel wells shall have mud flaps installed on them. 1526-031

CAB EXTERIOR FRONT & SIDE EMBLEMS
The cab shall include three (3) Spartan emblems. There shall be one (1) installed on the front air intake grille and two (2) for the exterior sides of the cab shipped loose with the chassis for installation by the body manufacturer.
5109-001

IGNITION
A master battery system with a keyless start ignition system shall be provided. Each system shall be controlled by a one-quarter turn Cole Hersee switch, both of which shall be mounted to the left of the steering wheel on the dash. A chrome push type starter button shall be provided adjacent to the master battery and ignition switches.

Each switch shall illuminate a green LED indicator light on the dash when the respective switch is placed in the “ON” position.

The starter button shall only operate when both the master battery and ignition switches are in the “ON” position.
5101-021

BATTERY
The single start electrical system shall include six (6) Harris BCI 31 925 CCA batteries with a 210 minute reserve capacity and 4/0 welding type dual path starter cables per SAE J541. 5106-003

BATTERY TRAY
The batteries shall be installed within two (2) steel battery trays located on the left side and right side of the chassis, securely bolted to the frame rails. The battery trays shall be coated with the same material as the frame.

The battery trays shall include drain holes in the bottom for sufficient drainage of water. A durable, nonconducting, interlocking mat made by Dri-Dek shall be installed in the bottom of the trays to allow for air flow and help prevent moisture build up. The batteries shall be held in place by non-conducting phenolic resin hold down boards.
5107-007

BATTERY BOX COVER
Each battery box shall include a steel cover which protects the top of the batteries. Each cover shall include flush latches which shall keep the cover secure as well as a black powder coated handle for convenience when opening.
5102-001

BATTERY CABLE
The starting system shall include cables which shall be protected by 275 degree F. minimum high temperature flame retardant loom, sealed at the ends with heat shrink and sealant. 5108-010

BATTERY JUMPER STUD
The starting system shall include battery jumper studs. These studs shall be located in the forward most portion of the driver's side lower step, 8.00 inches apart. The studs shall allow the vehicle to be jump started, charged, or the cab to be raised in an emergency in the event of battery failure. 5104-002

ALTERNATOR
The charging system shall include a 320 amp Leece-Neville 12 volt alternator. The alternator shall include a self-exciting integral regulator.
5105-001

STARTER MOTOR
The single start electrical system shall include a Delco brand starter motor. 5202-116

BATTERY CONDITIONER
A Kussmaul Auto Charge 40 LPC battery conditioner shall be supplied. The battery conditioner shall provide a 40 amp output for the chassis batteries and a 15 amp output circuit for accessory loads. The battery conditioner shall be shipped loose with the cab. The battery conditioner shall include an additional 12.00 feet of coiled wire for relocation by the body manufacturer. This additional wire shall be routed behind the driver’s seat.
5203-003

BATTERY CONDITIONER DISPLAY
A Kussmaul battery conditioner display shall be supplied. The battery conditioner display shall be mounted in front of the left side door just below the windshield. 5209-039

ELECTRICAL INLET LOCATION
An electrical inlet shall be installed on the left hand side of the cab ahead of the front door in the mid position.
5204-055

ELECTRICAL INLET
A Kussmaul 20 amp super auto-eject electrical receptacle shall be supplied. It shall automatically eject the plug when the starter button is depressed.

A single item or an addition of multiple items must not exceed the rating of the electric inlet that it’s connected to.

Amp Draw Reference List:

Kussmaul 40 LPC Charger - 5 Amps
Kussmaul 40/20 Charger - 8.5 Amps
Kussmaul 80 LPC Charger - 13 Amps
Kussmaul EV-40 - 6.2 Amps
Blue Sea P12 7532 - 7.5 Amps
Iota DLS-45/IQ4 - 11 Amps
1000W Engine Heater - 8.33 Amps
1500W Engine Heater - 12.5 Amps
120V Air Compressor - 4.2 Amps
120V Dometic HVAC - 15 Amps
5210-004

ELECTRICAL INLET CONNECTION
The electrical inlet shall be connected to the battery conditioner. 5206-010

ELECTRICAL INLET COLOR
The electrical inlet connection shall include a white cover. 5301-102

HEADLIGHTS
The cab front shall include four (4) rectangular LED headlamps with separate high and low beams mounted in bright chrome bezels. Each lamp shall include a heating system that de-ices the headlight. 5337-001

HEADLIGHT LOCATION
The headlights shall be located on the front fascia of the cab directly below the front warning lights. 5303-004

FRONT TURN SIGNALS
The front fascia shall include two (2) Whelen model 600 4.00 inches X 6.00 inches programmable amber LED turn signals which shall be installed in an outboard position within the front fascia chrome bezel.
5336-015

SIDE TURN/MARKER LIGHTS
The sides of the cab shall include two (2) Tecniq S170 LED side marker lights which shall be provided just behind the front cab radius corners. The lights shall be amber with chrome bezels. 5302-024

MARKER AND ICC LIGHTS
In accordance with FMVSS, there shall be five (5) Tecniq S170 LED cab marker lamps designating identification, center and clearance provided. These lights shall be installed on the face of the cab within full view of other vehicles from ground level. The lights shall be amber in color. 5350-092

HEADLIGHT AND MARKER LIGHT ACTIVATION
The headlights and marker lights shall be controlled through a rocker switch within easy reach of the driver. There shall be a dimmer switch within easy reach of the driver to adjust the brightness of the dash lights. The headlamps shall be equipped with the "Daytime Running" light feature, which shall illuminate the headlights when the ignition switch is in the "On" position and the parking brake is released.
5426-008

LIGHTBAR SWITCH
The light bar shall be controlled through a virtual button on the Vista display and control screen. There shall be an additional button located on the Vista display and control screen to control the clear lights. 5305-351

INTERIOR OVERHEAD LIGHTS
The cab shall include a Weldon LED dome lamp located over each door. The lights shall include push switches on each lamp to activate both the clear and red portions of the light individually. 5388-003

INTERIOR OVERHEAD LIGHTS ACTIVATION
The clear portion of each lamp shall be activated by opening the respective door and via the multiplex display.
5403-051

LIGHTBAR PROVISION
There shall be two (2) light bars installed on the cab roof. The light bars shall be provided and installed by the chassis manufacturer. The light bar installation shall include mounting and wiring to a control switch on the cab dash.
5450N-006

CAB FRONT LIGHTBAR MODEL
The cab shall be provided with two (2) Whelen model F4NMINI light bars. Each light bar shall be 21.50 inches in length and feature eight (8) customizable pods.

See the light bar layout for specific details.
5317-243

FRONT SCENE LIGHTS
The front of the cab shall include two (2) HiViz model Firetech FT-MB-12-FT-W scene lights installed on the brow of the cab.

Each lamp head shall operate on 12 volt DC and incorporate a 12 LED optic that combines both spot and flood lighting. Each lamp head shall draw 5.0 amps, generate 6,336 total lumens, and measure approximately 2.00 inches in height X 16.00 inches in width. The lamp heads and brackets shall be powder coated white.
5329-006

FRONT SCENE LIGHT LOCATION
There shall be two (2) scene lights mounted to the front brow of the cab in the outboard position. 5335-003

FRONT SCENE LIGHTS ACTIVATION
The front scene lighting shall be activated by a virtual button on the Vista display and control screen. 5306-065

SIDE SCENE LIGHTS
The side of the cab shall include two (2) Whelen 900 series 9SC0ENZR model scene lights, one (1) each side which shall be surface mounted with a chrome bezel. The Whelen lights shall offer LED lighting at a gradient 32-degree angle.
5318-004

SIDE SCENE LIGHT LOCATION
The scene lighting located on the left and right sides of the cab shall be mounted rearward of the cab “B” pillar in the 10.00 inch raised roof portion of the cab between the front and rear crew doors. 5316-007

SIDE SCENE ACTIVATION
The scene lights shall be activated by two (2) virtual buttons on the Vista display and control screen(s), one (1) for each light.
5308-300

GROUND LIGHTS
Each door shall include a Tecniq T44 LED ground light mounted to the underside of the cab step below each door. The lights shall include a polycarbonate lens, a housing which is vibration welded and LEDs which shall be shock mounted for extended life.
5386-011

GROUND LIGHTS
The ground lighting shall be activated by the opening of the door on the respective cab side and a rocker switch in the dash panel.
5309-003

LOWER CAB STEP LIGHTS
The middle step located at each door shall include a Tecniq T44 LED light which shall activate with the opening of the respective door. The lights shall include a polycarbonate lens, a housing which is vibration welded and LEDs which shall be shock mounted for extended life. 5382-007

INTERMEDIATE STEP LIGHTS
The intermediate step well area at each door shall include a TecNiq D06 LED light within a chrome housing. The egress step lights shall provide visibility to the step well area for the first step exiting the vehicle. The egress step lights shall activate with entry step lighting. 5310-002

MAP LIGHTS
A Roxter gooseneck style map light shall be provided. The light shall have a clear bulb and a control switch on the base. The light shall be located on the right hand side of the dash. 5312-003

ENGINE COMPARTMENT LIGHT
There shall be a LED NFPA compliant light mounted under the engine tunnel for area work lighting on the engine. The light shall include a polycarbonate lens, a housing which is vibration welded and a bulb which shall be shock mounted for extended life. The light shall activate automatically when the cab is tilted.
5406-119

DO NOT MOVE APPARATUS LIGHT
The front headliner of the cab shall include a flashing red TecNiq K50 LED light clearly labeled "Do Not Move Apparatus". In addition to the flashing red light, an audible alarm shall be included which shall sound while the light is activated.

The flashing red light shall be located centered left to right for greatest visibility.

The light and alarm shall be interlocked for activation when either a cab door is not firmly closed, or an apparatus compartment door is not closed, and the parking brake is released. 5422-002

MASTER WARNING SWITCH
A master switch shall be included, as a virtual button on the Vista display and control screen which shall be labeled “E Master” for identification. The button shall feature control over all devices wired through it. Any warning device switches left in the “ON” position when the master switch is activated shall automatically power up.
5409-002

HEADLIGHT FLASHER
An alternating high beam headlight flashing system shall be installed into the high beam headlight circuit which shall allow the high beams to flash alternately from left to right.

Deliberate operator selection of high beams will override the flashing function until low beams are again selected. Per NFPA, these clear flashing lights will also be disabled “On Scene” when the park brake is applied.
5425-018

HEADLIGHT FLASHER SWITCH
The flashing headlights shall be activated through a rocker switch on the switch panel. The rocker switch shall be clearly labeled for identification.
5401-002

INBOARD FRONT WARNING LIGHTS
The cab front fascia shall include two (2) Whelen 600 series Super LED front warning lights in the left and right inboard positions. The lights shall feature multiple flash patterns including steady burn for solid colors and multiple flash patterns for split colors. The lights shall be mounted to the front fascia of the cab within a chrome bezel.
5413-002

INBOARD FRONT WARNING LIGHTS COLOR
The warning lights mounted on the cab front fascia in the inboard positions shall be red. 5423-003

FRONT WARNING SWITCH
The front warning lights shall be controlled through a virtual control on the Vista display and control screen. This switch shall be clearly labeled for identification. 5404-002

INTERSECTION WARNING LIGHTS
The chassis shall include two (2) Whelen 600 series Super LED intersection warning lights, one (1) each side. The lights shall feature multiple flash patterns including steady burn for solid colors and multiple flash patterns for split colors.
5419-002

INTERSECTION WARNING LIGHTS COLOR
The intersection lights shall be red.
5420-002

INTERSECTION WARNING LIGHTS LOCATION
The intersection lights shall be mounted on the side of the bumper in the rearward position. 5402-002

SIDE WARNING LIGHTS
The cab sides shall include two (2) Whelen 600 series Super LED warning lights, one (1) on each side.

The lights shall feature multiple flash patterns including steady burn for solid colors and multiple flash patterns for split colors. The lights shall be mounted to the sides of the cab within a chrome bezel. 5418-002

SIDE WARNING LIGHTS COLOR
The warning lights located on the side of the cab shall be red. 5412-009

SIDE WARNING LIGHTS LOCATION
The warning lights on the side of the cab shall be mounted over the front wheel well forward from the center of the front axle.
5424-003

SIDE AND INTERSECTION WARNING SWITCH
The side warning lights shall be controlled through a virtual button on the Vista display and control screen. This button shall be clearly labeled for identification. 5449-049

REAR WARNING LIGHTS
The cab shall be prewired and contain a cutout for a Whelen TACTL5 Traffic Advisor control head to be installed by the body builder. The prewire shall be coiled under the center dash panel.

Wiring provisions shall be provided routed to the rear of the frame for OEM installation of up to eight (8) individual traffic advisor warning lights rated at no more than one (1) amp each.

The power to the control head shall be master power switched and activation dependent upon the state of the controllers switched position upon receiving power. 5510-004

SIREN CONTROL HEAD
A Whelen 295HFS2 electronic siren control head with remote amplifier shall be provided and flush mounted in the switch panel with a location specific to the customer’s needs. The siren shall feature 200-watt output, hands free mode and shall be in “standby” mode awaiting instruction. The siren shall offer radio broadcast, public address, wail, yelp, or piercer tones and hands free operation which shall allow the operator to turn the siren on and off from the horn ring if a horn/siren selector switch option is also selected.
5514-002

STEERING WHEEL HORN BUTTON SELECTOR SWITCH
A rocker switch shall be installed in the switch panel between the driver and officer to allow control of either the electric horn or the air horn from the steering wheel horn button. The electric horn shall sound by default when the selector switch is in either position to meet FMCSA requirements. 5527-004

AUDIBLE WARNING RH FOOT SWITCH
A foot switch wired to actuate the mechanical siren(s) shall be supplied for installation in the front section of the cab for officer actuation.
5527C-001

MECHANICAL SIREN FOOT SWITCH RH
The mechanical siren foot switch shall be a Linemaster model 491-S. 5527D-001

MECHANICAL SIREN FOOT SWITCH RH LOCATION
The mechanical siren foot switch shall be temporarily tied up with a coiled wire drop behind the center dash for installation by the customer on the right hand side accessible to the officer. 5512-042

AIR HORN AUXILIARY ACTIVATION
The air horn activation shall be accomplished by a black momentary push button on the switch panel. An air horn activation circuit shall be provided to the chassis harness pump panel harness connector. 5513-503

MECHANICAL SIREN BRAKE/AUXILIARY ACTIVATION
Two (2) red momentary siren brake rocker switches shall be provided in the switch panel on the dash. 5532-001

MECHANICAL SIREN INTERLOCK
The siren shall only be active when master warning switch is on to prevent accidental engagement. 5505-002

BACK-UP ALARM
An ECCO model 575 backup alarm shall be installed at the rear of the chassis with an output level of 107 dB. The alarm shall automatically activate when the transmission is placed in reverse. 5601-041

INSTRUMENTATION
An ergonomically designed instrument panel shall be provided. Each gauge shall be backlit with LED lamps. Stepper motor movements shall drive all gauges. The instrumentation system shall be multiplexed and shall receive ABS, engine, and transmission information over the J1939 data bus to reduce redundant sensors and wiring.

A twenty eight (28) icon lightbar message center with integral LCD odometer/trip odometer shall be included. The odometer shall display up to 999,999.9 miles. The trip odometer shall display 9,999.9 miles. The LCD message center screen shall be capable of custom configuration by the users for displaying certain vehicle status and diagnostic functions.

The instrument panel shall contain the following gauges:

One (1) three-movement gauge displaying vehicle speed, fuel level, and Diesel Exhaust Fluid (DEF) level. The primary scale on the speedometer shall read from 0 to 100 MPH, and the secondary scale on the speedometer shall read from 0 to 160 KM/H. The scale on the fuel and DEF level gauges shall read from empty to full as a fraction of full tank capacity. Red indicator lights in the gauge and an audible alarm shall indicate low fuel or low DEF at 1/8th tank level.

One (1) three-movement gauge displaying engine RPM, and primary and secondary air system pressures shall be included. The scale on the tachometer shall read from 0 to 3000 RPM. The scale on the air pressure gauges shall read from 0 to 150 pounds per square inch (PSI) with a red line zone indicating critical levels of air pressure. Red indicator lights in the gauge and an audible alarm shall indicate low air pressure.

One (1) four-movement gauge displaying engine oil pressure, coolant temperature, voltmeter, and transmission temperature shall be included. The scale on the engine oil pressure gauge shall read from 0 to 100 pounds PSI with a red line zone indicating critical levels of oil pressure. A red indicator light in the gauge and audible alarm shall indicate low engine oil pressure. The scale on the coolant temperature gauge shall read from 100 to 250 degrees Fahrenheit (°F) with a red line zone indicating critical coolant temperatures. A red indicator light in the gauge and audible alarm shall indicate high coolant temperature. The scale on the voltmeter shall read from 9 to 18 volts with a red line zone indicating critical levels of battery voltage. A red indicator light in the gauge and an audible alarm shall indicate high or low system voltage. The low voltage alarm shall indicate when the system voltage has dropped below 11.8 volts for more than 120 seconds in accordance with the requirements of NFPA 1901. The scale on the transmission temperature gauge shall read from 100 to 300 degrees °F with a red line zone indicating critical temperatures. A red indicator light in the gauge and an audible alarm shall indicate a high transmission temperature.

The light bar portion of the message center shall include twenty-eight (28) LED backlit indicators. The lightbar shall be split with fourteen (14) indicators on each side of the LCD message screen. The lightbar shall contain the following indicators and produce the following audible alarms when supplied in conjunction with applicable configurations:

RED INDICATORS
Stop Engine - indicates critical engine fault
Air Filter Restricted - indicates excessive engine air intake restriction Park Brake - indicates parking brake is set
Seat Belt - indicates a seat is occupied and corresponding seat belt remains unfastened Low Coolant - indicates critically low engine coolant
Cab Tilt Lock - indicates the cab tilt system locks are not engaged.

AMBER INDICATORS
Malfunction Indicator Lamp (MIL) - indicates an engine emission control system fault Check Engine - indicates engine fault
Check Transmission - indicates transmission fault
Anti-Lock Brake System (ABS) - indicates anti-lock brake system fault High exhaust system temperature – indicates elevated exhaust temperatures Water in Fuel - indicates presence of water in fuel filter Wait to Start - indicates active engine air preheat cycle Windshield Washer Fluid – indicates washer fluid is low DPF restriction - indicates a restriction of the diesel particulate filter Regen Inhibit-indicates regeneration of the DPF has been inhibited by the operator Range Inhibit - indicates a transmission operation is prevented and requested shift request may not occur.

SRS - indicates a problem in the supplemental restraint system Check Message - indicates a vehicle status or diagnostic message on the LCD display requiring attention.

GREEN INDICATORS
Left and Right turn signal indicators
ATC - indicates low wheel traction for automatic traction control equipped vehicles, also indicates mud/snow mode is active for ATC system
High Idle - indicates engine high idle is active.

Cruise Control - indicates cruise control is enabled
OK to Pump - indicates the pump is engaged and conditions have been met for pump operations Pump Engaged - indicates the pump transmission is currently in pump gear Auxiliary Brake - indicates secondary braking device is active

BLUE INDICATORS
High Beam indicator

AUDIBLE ALARMS
Air Filter Restriction
Cab Tilt Lock
Check Engine
Check Transmission
Open Door/Compartment
High Coolant Temperature
High or Low System Voltage
High Transmission Temperature
Low Air Pressure
Low Coolant Level
Low DEF Level
Low Engine Oil Pressure
Low Fuel
Seatbelt Indicator
Stop Engine
Water in Fuel
Extended Left/Right Turn Signal On
ABS System Fault
5624-001

BACKLIGHTING COLOR
The instrumentation gauges and the switch panel legends shall be backlit using red LED backlighting. 5701-300
RADIO
A Jensen brand radio with weather band, AM/FM stereo receiver, rear RCA input pigtail connector, Bluetooth, satellite radio capability, and a covered front auxiliary mini stereo input with iPod ready front and rear USB inputs shall be installed in a customer specified location. 5736-200

RADIO LOCATION
The radio shall be installed in the right hand overhead position above the officer. 5707-003

AM/FM ANTENNA
A small antenna shall be located on the right hand side of the cab roof for AM/FM and weather band reception.
5737-200

RADIO SPEAKERS
There shall be two (2) speakers installed in the front portion of the cab recessed overhead and two (2) speakers installed on the upper rear wall of the cab. The speakers shall be provided for connection to the sound system.
5726-002

CAMERA LEFT HAND
One (1) Audiovox Voyager heavy duty rearview teardrop shaped chrome plated housing camera shall be mounted on the driver side of the cab below the windshield ahead of the front door at approximately the same level as the cab door handles. The camera display shall activate when the left side turn signal is activated.
5727-002

CAMERA RIGHT HAND
One (1) Audiovox Voyager heavy duty rearview teardrop shaped chrome plated housing camera shall be mounted on the officer side of the cab below the windshield ahead of the front door at approximately the same level as the cab door handles. The camera display shall activate when the right side turn signal is activated.
5728-009

CAMERA REAR
One (1) Audiovox Voyager heavy duty box shaped HD camera shall be shipped loose for OEM installation in the body to afford the driver a clear view to the rear of the vehicle.

The camera system shall include a one-way communication device that shall be an integral part of the rear camera for the use of voice commands directly to the driver. The rear camera display shall activate when the vehicle’s transmission is placed in reverse.
5731-004

CAMERA DISPLAY
The camera system shall be wired to a single Weldon Vista display located on the driver’s side dash. The camera system display can be activated through the Vista display panel. 5732-002

CAMERA SPEAKER
The rear camera shall be wired to speaker(s) in the cab and shall audible to the driver and officer. There shall be a virtual button provided on the Vista display and control panel to deactivate the speaker(s). 5702-023

TWO-WAY RADIOS
A radio wire conduit with a pull wire included shall be installed and routed from behind the dash to under the officer’s seat for radio installation by the customer. The officer’s under seat storage area shall include an access hole for the conduit cut into the rear face of the seat box. The hole shall be approximately 1.00 inch from the bottom and 1.00 from the inner wall of the seat box. 8814-002

CAB EXTERIOR PROTECTION
The cab face shall have a removable plastic film installed over the painted surfaces to protect the paint finish during transport to the body manufacturer.
8806-001

FIRE EXTINGUISHER
A 2.50 pound D.O.T approved fire extinguisher with BC rating shall be shipped loose with the cab. 8807-002

ROAD SAFETY KIT
The cab and chassis shall include one (1) emergency road safety triangle kit. 8810-001

DOOR KEYS
The cab and chassis shall include a total of four (4) door keys for the manual door locks. 8003-197

WARRANTY
Purchaser shall receive a Custom Chassis Two (2) Years or 36,000 Miles limited warranty in accordance with, and subject to, warranty certificate RFW0102. The warranty certificate is incorporated by reference into this proposal, and included with this proposal or available upon request. 8030-006

CHASSIS OPERATION MANUAL
There shall be two (2) digital copies of the chassis operation manual provided with the chassis. The digital data shall include a parts list specific to the chassis model. 8031-024

ENGINE AND TRANSMISSION OPERATION MANUALS
The following manuals specific to the engine and transmission models ordered will be included with the chassis in the ship loose items:
(1) Hard copy of the Engine Operation and Maintenance manual with digital copy (1) Digital copy of the Transmission Operator’s manual
(1) Digital copy of the Engine Owner’s manual
8032-018

ENGINE SERVICE MANUALS
There shall be one (1) printed hard copy set of Cummins engine service reference manuals which shall be provided with the chassis.
8033-002

TRANSMISSION SERVICE MANUALS
There shall be one (1) printed hard copy set of Allison 4000 transmission service manuals included with the chassis.
8805-007

CAB/CHASSIS AS BUILT WIRING DIAGRAMS
The cab and chassis shall include two (2) digital copies of wiring schematics and option wiring diagrams.
8039-001

SALES TERMS
The sale of the chassis shall be governed by the terms contained on the Sales Terms – Acceptance of Purchase Order document, a copy of which is attached to this option. 9005-002

DRIVELINE LAYOUT CONFIRMATION
During the design phase of the chassis the Spartan Chassis driveline engineer shall submit the driveline layout to an OEM engineer to review the chassis design for any potential problems integrating the OEM body to the chassis. The OEM engineer shall provide approval to the driveline engineer prior to driveline bills of materials being released.

Fri Sep 16 2022 Quote #: 0022355 Page 1 of 14
Quote Summary with Notes
Customer: Dinuba Fire Department Dealership: Fire Apparatus Solutions 496 E. Tulare Street 1762 S Sycamore Ave
Dinuba, CA 93618 Rialto, CA 92376
Quote No: 0022355 Quote Name: Dinuba FD 105' Aerial 2022 S.O.#: Unit Type:

Option ID Description
General Info General Info Section
900992 Smeal 105' Rear Mount Aerial Ladder
100973 Smeal Branded Badging and Logo's
911085 Destination, United States
900998 Intent of Specifications, Aerial, Pump
911059 Bidding Prerequisites, United States
911060 Standards Version, NFPA 19012016
911064 Inspection Certificate, NFPA 1901 Compliance
911070 Documentation, NFPA
980016 Owner's Manuals, Electronic, (1) USB Drive
901037 Aerial Operations/Parts/Maintenance Manuals, (1) Printed Copy, (1) USB Drive
121744 Aerial Demonstration, Aerial Ladder, (3) Consecutive Days 911081 Misc. Equipment Allowance, 2,500 Lb.
901080 Tilt Table Test, Not Required, Chassis ESC
980012 Pump Certification, Independent Third Party
911066 Pump Certification Measure, U.S. GPM
911304 Apparatus Production Photos
911073 PreConstruction Meeting, OEM Factory
911074 Final Inspection, OEM Factory, Required
900489 Overall Height, 141" (11'9")
900255 Overall Length, 500 (41'8")
900576 Wheelbase, 228 (19'0")
900653 Angle of Approach, 8 Degrees
900674 Angle of Departure, 8 Degrees
Chassis Chassis Section
910013 Custom Chassis, Spartan, Gladiator
910020 Axles, Tandem
001360 OEM Chassis Preparations, Spartan Metro Star/Gladiator 001200 Mud Flaps, Front Chassis Provided, Rear OEM Provided 910021 Cab Electrical, Multiplex
007487 Extend Chassis Air Tank Drains, Outside of Body
September 16, 2022 Quote #: 0022355 Page 2 of 14
Option ID Description
By: Roy Cobb, 916-677-9837 https://www.smeal.com/ Page 2 of 14 UPOxxxxxxx Grab Handles, (2), Mounted Vertically on Front of Chassis Cab 001379 Heat Exchanger, Chassis Supplied and Installed
100964 Relocate Cab Tilt Pendant, Standard Location
910156 Front Bumper, Chassis Supplied and Installed
UPOxxxxxxx Center Front Bumper Storage Well Cover
UPOxxxxxxx Map Console, 3Slot MultiSpec to Match Cab Interior, (2) Radio Slots (Dinuba)
911113 Map Console Location, Engine Tunnel Mounted, DropIn 008571 Battery Charger, Chassis Supplied, OEM Installed UPO0058220 No Charger Cover
110034 Helmet Brackets (4), Zico, UHH1
UPOxxxxxxx Flashlights, (4) Streamlight SL20XP LED Rechargeable Orange w/ Charger Sleeve
111539 Flashlights (2), Streamlight, ESpot LiteBox, LED, Orange, 45855, Vehicle Mount System
UPOxxxxxxx SCBA Compartment Rear Facing, Behind Driver's Seat (Dinuba) UPOxxxxxxx Gear Compartment Behind Engine Tunnel, (Dinuba) UPOxxxxxxx SCBA Compartment Rear Facing, Behind Officer's Seat (Dinuba) 112100 EMS Finish, MultiSpec to Match Cab Interior, 3 EMS Compartments Water/Foam Tanks Water/Foam Tanks Section
110073 Water Tank, ProPoly, 400 U.S. Gallons
005143 Water Tank Mounting, ProPoly, Aerials
002230 Water Tank Drain, 11/2" Valve, Aerials
910158 Water Tank Fill Tower, ProPoly, Black
003589 Water Tank Level Gauge, Class 1 IntelliTank ITL12093, Pump Operator's Panel
004776 Water Tank Overflow, ProPoly, 4"
005537 Foam Cell, Pro Poly, 40 U.S. Gallon
910172 Foam Cell Type, Class A
910168 Foam Cell Fill Tower, Pro Poly, Black
002929 Foam Cell Level Gauge, Class 1 IntelliTank ITL12105, Class A Foam Hose Bed Hose Bed Section
003506 Hose Bed, EHL, Black Bedliner Coating Finish (105'/125'/RMP) 911300 EHL Hose Load, DoubleJacket Hose, 1000' of 5"
Body / Pump Module Body / Pump Module
002647 Body, 100" Wide, Rear Mount Aerial, TandemAxle, Aluminum, 1/8" (75'/UT 100'/105'/107)
120790 Side Compartment Doors, Lap Doors, Painted
901192 Inner Door Pan, Side Doors, Painted Main Body Color 101229 Compartment Door Handles, Lap Doors, All NonLocking (10), DRing Handle(s)
009818 Rear Compartment Door, (1), Painted Lap Door, Grab Handle 901195 Inner Door Pan, (1) Rear Door, Painted Main Body Color 121085 Compartment Lighting, OnScene, Access Series LED (20) 000934 Compartment Finish, Bedliner Coating, Gray
September 16, 2022 Quote #: 0022355 Page 3 of 14
Option ID Description
By: Roy Cobb, 916-677-9837 https://www.smeal.com/ Page 3 of 14 120482 Flooring, Black Turtle Tiles, All Interior Body Compartment Shelves Only
000474 Air Release and Drain Holes, All Compartments
000440 Sill Protectors, Anodized Aluminum, Lap Door Compartments 112149 Fuel Fill, OEM Brushed Door, Driver's Side
121956 Wheel Well Storage Design, Tandem Axle, Smart Storage 121545 Driver's (Left) Side Body, MidSize RMA, Tandem Axle, L1 Full, L2 Upper, L3 Upper, L4 Upper, L5 Full
L1 L1 Components
Height Height 62
Width Width 28"
Upper Depth Upper Depth 13"
Lower Depth Lower Depth 22"
Divide Height Intermediate Divide Height 30"
900983 Lap Door Hinge, Vertical, Rearward
002743 Shelf (1), Adjustable, Aluminum, Shallow Depth (2 Struts), Bedliner Coating
003437 Tray (1), FloorMounted Roll Out, Innovative Ind., 300# (SM3LP), 100% Extension, Bedliner Coating
120785 Compartment Struts, Vertical, Welded Aluminum
Cmpt. Layout The compartment layout shall be detailed at the preconstruction meeting.

L2 L2 Components
Height Height 32"
Width Width 39"
Upper Depth Upper Depth 13"
Lower Depth Lower Depth 13"
Divide Height Intermediate Divide Height "
900982 Lap Door Hinge, Horizontal, Top
002743 Shelf (1), Adjustable, Aluminum, Shallow Depth (2 Struts), Bedliner Coating
120785 Compartment Struts, Vertical, Welded Aluminum
Cmpt. Layout The compartment layout shall be detailed at the preconstruction meeting.

L3 L3 Components
Height Height 32"
Width Width 39"
Upper Depth Upper Depth 13"
Lower Depth Lower Depth 13"
Divide Height Intermediate Divide Height "
900982 Lap Door Hinge, Horizontal, Top
Cmpt. Layout The compartment layout shall be detailed at the preconstruction meeting.

L4 L4 Components
Height Height 18"
Width Width 53"
Upper Depth Upper Depth 13"
September 16, 2022 Quote #: 0022355 Page 4 of 14
Option ID Description
By: Roy Cobb, 916-677-9837 https://www.smeal.com/ Page 4 of 14 Lower Depth Lower Depth 13"
Divide Height Intermediate Divide Height "
900982 Lap Door Hinge, Horizontal, Top
Cmpt. Layout The compartment layout shall be detailed at the preconstruction meeting.

L5 L5 Components
Height Height 50"
Width Width 27"
Upper Depth Upper Depth 13"
Lower Depth Lower Depth 23"
Divide Height Intermediate Divide Height 23"
900981 Lap Door Hinge, Vertical, Forward
002743 Shelf (1), Adjustable, Aluminum, Shallow Depth (2 Struts), Bedliner Coating
120785 Compartment Struts, Vertical, Welded Aluminum
Cmpt. Layout The compartment layout shall be detailed at the preconstruction meeting.
121926 WL1, Smart Storage, Air Bottle Storage, OEM Brushed SS Door, Triple Triangle Design
121933 WL2, Smart Storage, Open Storage, OEM Brushed SS DropDown Door
121936 WL3, Smart Storage, Air Bottle Storage, OEM Brushed SS Door, Triple Triangle Design
121583 Officer's (Right) Side Body, MidSize RMA, Tandem Axle, R1 Full, R2 Upper, R3 Upper, R4 Upper, R5 Full
R1 R1 Components
Height Height 62
Width Width 28"
Upper Depth Upper Depth 13"
Lower Depth Lower Depth 22"
Divide Height Intermediate Divide Height 25"
900983 Lap Door Hinge, Vertical, Rearward
002743 Shelf (1), Adjustable, Aluminum, Shallow Depth (2 Struts), Bedliner Coating
003437 Tray (1), FloorMounted Roll Out, Innovative Ind., 300# (SM3LP), 100% Extension, Bedliner Coating
120785 Compartment Struts, Vertical, Welded Aluminum
Cmpt. Layout The compartment layout shall be detailed at the preconstruction meeting.

R2 R2 Components
Height Height 32"
Width Width 39"
Upper Depth Upper Depth 13"
Lower Depth Lower Depth 13"
Divide Height Intermediate Divide Height "
900982 Lap Door Hinge, Horizontal, Top
September 16, 2022 Quote #: 0022355 Page 5 of 14
Option ID Description
By: Roy Cobb, 916-677-9837 https://www.smeal.com/ Page 5 of 14 002743 Shelf (1), Adjustable, Aluminum, Shallow Depth (2 Struts), Bedliner Coating
120785 Compartment Struts, Vertical, Welded Aluminum
Cmpt. Layout The compartment layout shall be detailed at the preconstruction meeting.

R3 R3 Components
Height Height 32"
Width Width 39"
Upper Depth Upper Depth 13"
Lower Depth Lower Depth 13"
Divide Height Intermediate Divide Height "
900982 Lap Door Hinge, Horizontal, Top
Cmpt. Layout The compartment layout shall be detailed at the preconstruction meeting.

R4 R4 Components
Height Height 18"
Width Width 53"
Upper Depth Upper Depth 13"
Lower Depth Lower Depth 13"
Divide Height Intermediate Divide Height "
900982 Lap Door Hinge, Horizontal, Top
Cmpt. Layout The compartment layout shall be detailed at the preconstruction meeting.

R5 R5 Components
Height Height 50"
Width Width 51"
Upper Depth Upper Depth 13"
Lower Depth Lower Depth 23"
Divide Height Intermediate Divide Height 23"
900984 Lap Door Hinge, Vertical, Double Doors
002743 Shelf (1), Adjustable, Aluminum, Shallow Depth (2 Struts), Bedliner Coating
002745 Shelf (1), Adjustable, Aluminum, Full Depth (4 Struts), Bedliner Coating 120785 Compartment Struts, Vertical, Welded Aluminum
Cmpt. Layout The compartment layout shall be detailed at the preconstruction meeting.
121942 WR1, Smart Storage, Air Bottle Storage, OEM Brushed SS Door, Triple Triangle Design
121949 WR2, Smart Storage, Open Storage, OEM Brushed SS DropDown Door
121952 WR3, Smart Storage, Air Bottle Storage, OEM Brushed SS Door, Triple Triangle Design
901045 Rear Side Body, Rear Mounts, Torque Box Compartment 008773 Sub Frame Body Mounts, GS36, HotDip Galvanized Steel, Aerial (105')
005118 Rub Rails, "C" Channel Design
000516 Tow Option, Rear, Tow Eye, Two (2), Chrome
September 16, 2022 Quote #: 0022355 Page 6 of 14
Option ID Description
By: Roy Cobb, 916-677-9837 https://www.smeal.com/ Page 6 of 14 UPO0040538 Modifications
121960 Wheel Wells, Rear, Tandem Axle, Black Polymer, Smart Storage 121958 Fenderettes, (4), Tandem Axle, Stainless Steel, Smart Storage 120489 Exhaust Heat Deflector Shield, 4"
002427 License Plate Bracket
006375 Stainless Steel Screws, Aerial
911283 NO Bag of Bolts
900963 Walkways/Overlays/Stepping Surfaces, Tread Plate, NFPA 1901 007906 Turntable Access Ladder, Driver's Side, Grote LED Light, Knurled Aluminum Handrails, Rear Mounts
000505 Overlay, Tread Plate, Vertical Areas of Both Front Compartments 007897 Front Steps and Lighting, Cast Products, Folding Steps (4), Driver's Side, Smeal Logo
007902 Front Steps and Lighting, Cast Products, Folding Steps (4), Officer's Side, Smeal Logo
900960 Handrail Material, Knurled Aluminum
UPOxxxxxxx Front Steps and Lighting, Cast Products, Folding Steps (2), Rear of Front Stabilizers, One Each Side, Smeal Logo
003598 Handrail, Body (Front), Top, Driver's Side, Knurled Aluminum 000521 Handrail, Body (Front), Top, Officer's Side, Knurled Aluminum 120676 Handrails, Pump Module, Above Pump Panel, Horizontal, Both Sides, Knurled Aluminum
001316 Ladder Storage, In Torque Box, (2) Enclosed Compartments (105') 121676 Ground Ladder Package, DuoSafety, (1) 10' Attic (585A), (1) 14' Fresno (701), (1) 16' Roof (875A), (1) 24' TwoSection (900A), (1) 35' ThreeSection (1225A)
009223 Pike Pole Storage, In Upper Portion of Torque Box, (6) Tubes 121692 Pike Pole Package, DuoSafety, Fiberglass, Standard Hooks, (2) 6' Poles (FP6), (2) 8' Poles (FP8), (2) 12' Poles (FP12)
009226 Pike Pole Storage, In Upper Portion of Torque Box, (2) Trays 121263 Pike Poles (2), Fire Hooks Unlimited, 4' Fiberglass, National Hook, Ash Core, DHandle, NHF4 w/D
900953 Wheel Chock Storage, Under Rear of Body, Driver's Side 001204 Wheel Chocks, (1) Pair, Zico SAC44 and Bracket, OEM Installed 002648 Pump Module, Rear Mount Aerial, Independent, 1/8" Aluminum (105')
004731 Pump Compartment Internal Lighting, LED, OnScene 009864 Running Board, Driver's Side, BoltOn, Tread Plate 010108 Running Board, Officer's Side, BoltOn, Tread Plate 009863 PullOut Platforms (2), Both Sides of Pump Module, Innovative Industries
009985 Tread Plate Dunnage, Above Pump Module, Tread Plate Cover 005149 Access Panel, Pump, Front Pump Module, Removable, Tread Plate, Compression Latches, Side Mounts, RMA's
000460 Access Panel, Pump, Officer's Side Pump Module, SideHinged, Tread Plate, Compression Latches
121716 Pump Panels, Rear Mount Aerial and Platform, Controls on Driver's Side, Black Bedliner Coating Finish, IC Bezels/Trim Rings/Labels September 16, 2022 Quote #: 0022355 Page 7 of 14
Option ID Description
By: Roy Cobb, 916-677-9837 https://www.smeal.com/ Page 7 of 14 003659 Pump Panel Lighting, Side Panels, LED, OnScene Night Axe 910612 Pump Panel Lighting Activation, Automatic with Park Brake Engaged UPOxxxxxxx Speaker, University Sound, Left Side Of Pump Module, With Volume Control (D2263021) (DCT22152)
Pump / Foam
System
Pump / Foam System
100157 Pump, Waterous, SingleStage, 2000 GPM, CSUC20, Flame Plated Impeller Hubs
910618 Grafoil Packing, Waterous
002792 Anodes, Waterous, Magnesium, 2 Discharge, 2 Intake 910622 Pump Rating, 1500 GPM
910640 Pump Mounting, Independent Pump Module
100272 Pump Shift, Chassis Sup/Instl, ElectricOverAir, Lights Incorporated with Pres. Gov.
101457 Relocate Chassis Supplied Knee Area Pump Shift
UPOxxxxxxx Governor, Total Pressure Governor (UVTPG), Class 1 UPOxxxxxxx Pump Hour Meter
002210 Intake Relief Valve, Pump, Elkhart, Factory Preset 006588 Primer, Trident, AirPrime (3Barrel), AirOperated Valve (31.001.7) 000112 Master Drain Valve, Trident
000087 Overheat Protection Manager (OPM), Waterous, With Lights 005848 Pump Color Painted Gray Intakes Primary Body Color 901166 Pump Manuals Waterous, (2)
111069 Pump and Engine Cooling System, Inn. Cntrls, 3/8" I.D., Hose, Controls on Pump Panel
100743 Foam System, Eductor, Akron, 3096 Bypass, 95 GPM, Class A, Flush System
Shop Note:

Only one (1) fill tube for the Foam Refill System
980014 Foam System Testing, Single System
006643 Manifold, Waterous, Standard, Side Mounts, NonFoam 910503 Akron 8800/8600 Push/Pull Discharges (RC10 on 3" or Larger) Manual Intakes
910589 Gauge Brand, Thuemling, 21/2" Liquid Filled (No Bezel) PSI 0400 006940 Master Gauges, Thuemling, 41/2", Liquid Filled, PSI 300400 111067 Test Ports, Pressure/Vacuum, Inn. Cntrls, Operators Panel 910527 Hardware Brand, South Park, NH Intake Swivels, NH Discharges, TFT Storz
100377 Drains, Innovative Controls, Manual Lift Handle
Shop Note:

No auto drains will be installed on the front bumper or crosslays. These need to be manual.
911305 Plumbing Labels, OEM Standard
Tank/Pump Plumbing
Labels
Tank/Pump Plumbing Labels See label order form (required) 100349 Pump to Tank Fill, 2", Akron 8800 2" Manual Valve, IC PushPull Handle
September 16, 2022 Quote #: 0022355 Page 8 of 14
Option ID Description
By: Roy Cobb, 916-677-9837 https://www.smeal.com/ Page 8 of 14 100310 Tank to Pump, 3", Akron 8800 3" Manual Valve, IC PushPull Handle
Shop Note:

Reverse the tank lever handle; label "PULL TO CLOSE"
Intakes Intakes
100381 Main Intake, Driver Side, 6", Short Tube, FullBody Pump, MNST UPOxxxxxxx TFT 6" FNST x 5" Storz, Jumbo Ball intake Valve AB3STNX, 5" Storz Cap with Lanyard A01ST
UPO0050330 None
UPO0050331 None
UPO0046300 No Cap
002588 Auxiliary Intake, DriverSide, 21/2", Fully Recessed 007059 Valve, 21/2", Akron, Manual, 8825, Stainless Ball, TS Handle 001246 Plug, NH, 21/2", South Park, HPC3008AC
100385 Main Intake, Officer Side, 6", Short Tube, FullBody Pump, MNST UPOxxxxxxx TFT 6" FNST x 5" Storz, Jumbo Ball intake Valve AB3STNX, 5" Storz Cap with Lanyard A01ST
UPO0046301 No Cap
Intake Labels Intake Labels See label order form (required) Discharges Discharges
002545 Discharge, DriverSide, 21/2", NST (250 GPM NFPA Rated) 910534 Foam Capable Discharge
Shop Note:

This is the only foam capable discharge. There will be special plumbing involved for the Akron Foam Eductor,
111712 Valve, 21/2", Akron, Manual, 8625, Stainless Ball, Innovative Controls Push Pull Controller (Rack and Sector)
005849 Pressure Gauge, 21/2", Thuemling, Liquid Filled psi 0400 100542 Elbow (45 Deg.) 21/2" FNH x 21/2" MNH (SE394505AC) Adapter, 21/2" FNH x 11/2" MNH (A3720AC) NH Cap (HCC2804AC), Chrome, South Park
002545 Discharge, DriverSide, 21/2", NST (250 GPM NFPA Rated) 111712 Valve, 21/2", Akron, Manual, 8625, Stainless Ball, Innovative Controls Push Pull Controller (Rack and Sector)
005849 Pressure Gauge, 21/2", Thuemling, Liquid Filled psi 0400 100542 Elbow (45 Deg.) 21/2" FNH x 21/2" MNH (SE394505AC) Adapter, 21/2" FNH x 11/2" MNH (A3720AC) NH Cap (HCC2804AC), Chrome, South Park
002538 Discharge, OfficerSide, 21/2", NST (250 GPM NFPA Rated) 100659 Valve, 21/2", Akron, Manual, 8825, Stainless Ball, Innovative Controls Push Pull Controller (Operators Panel)
005849 Pressure Gauge, 21/2", Thuemling, Liquid Filled psi 0400 100527 Elbow (30 Deg.) 21/2" FNH x 21/2" MNH (SE393010AC) NH Cap (HCC2808AC), Chrome, South Park
002553 Discharge, OfficerSide, 4", NST (625 GPM NFPA Rated) 100642 Valve, 3", Akron, Gear, 8630, Stainless Ball, 4" Handwheel with Vert.

Position Indicator
005849 Pressure Gauge, 21/2", Thuemling, Liquid Filled psi 0400 September 16, 2022 Quote #: 0022355 Page 9 of 14
Option ID Description
By: Roy Cobb, 916-677-9837 https://www.smeal.com/ Page 9 of 14 100612 Elbow (30 Deg.) 4" FNH x 5" Storz (AH3STNP), Storz Cap (A01ST), TFT
121828 Discharge, Front Bumper DriverSide, 11/2", Chassis Installed Plumbing, Above Gravelshield, NST
Shop Note:

The front bumper shall NOT have any auto drains, they will be manual. 100658 Valve, 21/2", Akron, Manual, 8825, Stainless Ball, Innovative Controls Push Pull Controller
005849 Pressure Gauge, 21/2", Thuemling, Liquid Filled psi 0400 910526 Preconnect Discharge
006998 Crosslays, Above Front Stabilizers, (2) 11/2" and (1) 21/2" 007013 Preconnect Hose Bed Housing Coating, Abraded Finish 007018 Flooring, DuraDek
000205 Crosslay Rollers
009842 Crosslay Dividers (2), Abraded Aluminum, Notched 007020 Crosslay Cover, Hinged Tread Plate, Side Mount
Shop Note:

Non Skid tread plate to be used.
110291 Crosslay End Covers, Vinyl, CRail Top and Footman Loop / JHook on Bottom, Black
910701 Preconnect, Crosslay/Speedlay, 11/2", NST
Shop Note:

The crosslay shall NOT have any auto drains, they will be manual. 910654 Crosslay Load, 200' of 13/4" Hose, Single Stack 100653 Valve, 2", Akron, Manual, 8820, Stainless Ball, Innovative Controls Push Pull Controller
005849 Pressure Gauge, 21/2", Thuemling, Liquid Filled psi 0400 910526 Preconnect Discharge
910701 Preconnect, Crosslay/Speedlay, 11/2", NST
Shop Note:

The crosslay shall NOT have any auto drains, they will be manual. 910654 Crosslay Load, 200' of 13/4" Hose, Single Stack 100653 Valve, 2", Akron, Manual, 8820, Stainless Ball, Innovative Controls Push Pull Controller
005849 Pressure Gauge, 21/2", Thuemling, Liquid Filled psi 0400 910526 Preconnect Discharge
910702 Preconnect, Swivel, Crosslay/Speedlay, 21/2", NST Shop Note:

The crosslay shall NOT have any auto drains, they will be manual. 910651 Crosslay Load, 150' of 21/2" Hose, Single Stack 100658 Valve, 21/2", Akron, Manual, 8825, Stainless Ball, Innovative Controls Push Pull Controller
005849 Pressure Gauge, 21/2", Thuemling, Liquid Filled psi 0400 910526 Preconnect Discharge
100768 Booster Reel, Hannay, Aluminum, Polished, Electric Rewind, 200' of 1" Hose Capacity
910703 Booster Reel Location, Dunnage, Above the Pump
September 16, 2022 Quote #: 0022355 Page 10 of 14
Option ID Description
By: Roy Cobb, 916-677-9837 https://www.smeal.com/ Page 10 of 14 Shop Note:

The booster reel will be mounted on the officers side next to the cord reel.
100648 Valve, 11/2", Akron, Manual, 8815, Stainless Ball, Innovative Controls Push Pull Controller
100809 Booster Hose, 1", 800 lb Test, 200', (2) 100' Sections 100831 Rewind Switches, Booster Reel, (1) Officer's Side Pump Panel, (1) Foot Switch Below Running Board
007596 Discharge, Aerial Waterway, 4" (UT100'/105'/110'/125') 101350 Valve, 4", Akron, Electric, 8940, Composite Ball, 9335 Navigator Pro Controller (Valve, Pressure, Flow)
Discharge Labels Discharge Labels See label order form (required) Low Voltage Low Voltage
002956 Electrical System, Aerial, Weldon VMUX Multiplex, QL12 Harnesses, Sealed Switches
911058 Electrical System Test, 12 Volt
002842 Tail Lights, LED, Whelen, 600 Series, StopTail (Separate) (604BTT)/ Turn (604T)/Warning, 4Light Vertical Casting
002192 Switch, Rear Work Light, At Rear/Reverse
006766 Turn Signals, (2) in Wheel Well Area, LED, TruckLite, Model 21 100958 Ground Lights, LED, T44, Tecniq, Activation by Park Brake 006296 Parking Lights, Rear Fender Wells, LED, Innovative Lighting 007397 Clearance Lights, With Rubber Extension Arms, LED, Grote (65282) and TruckLite (35741R ID), Red
004882 Camera System, BackUp, Chassis Supplied, OEM Installed 100040 Intercom System, Sigtronics US45S, 4 Cab Position, Wired Driver/ Officer (SE8), 2 Wired Crew (SE2)
100060 Additional Intercom Position, (1) Pump Panel, Sigtronics US67S, Headset Extension Cable
100061 Additional Intercom Position, (1) Rear Body, Driver's Side, Sigtronics US67S, Headset Extension Cable
UPOxxxxxxx Radio Interface Cable, Sigtronics, Y Adapter (2) 911317 Upper Zone A, Chassis Supplied and Installed
110409 Upper Zone C, Beacons (2), Whelen, L31 LED
Upper Zone C Light/
Lens Color
Light/Lens Color Red LED's with Clear Lenses
110473 Lower Zone Warning Lights (4 OEM Provided), A (0), B (1), C (2), D (1), Whelen, LED, 600 Series
Lower Zone Light/
Lens Color
Light/Lens Color Red LED's with Clear Lenses
003120 Traffic Advisor, Whelen, 6Light, 5mm LED LowProfile, TAL65, TACTL5 Controller
910738 Traffic Directional Light Location, Rear Body Face, Recess Mounted 000890 Air Horn Activation, Push Button on Pump Panel, Driver's Side 110631 Scene Lights, Pair, 12V, Whelen, Surface Mount, LED 900 Series Gradient OptiScene
910851 Lighting Location, Rear Face of Body, Both Sides September 16, 2022 Quote #: 0022355 Page 11 of 14
Option ID Description
By: Roy Cobb, 916-677-9837 https://www.smeal.com/ Page 11 of 14 110838 Lighting Activation, On VMux Screen and Pump Panel, 'REAR SCENE', Wired to Reverse and Rear Work Light Switch
110589 Scene Lights (2), 12V, FRC, Pedestal Mount, LED Spectra 20,000 Lumen, Switch on Lighthead, Model SPA570Q20ON
910845 Lighting Location, On Top of the Body, Rearward, Both Sides 110848 Lighting Activation, Pair, In Cab and On Pump Panel, 'LEFT SCENE' and 'RIGHT SCENE', Rocker Switches
110589 Scene Lights (2), 12V, FRC, Pedestal Mount, LED Spectra 20,000 Lumen, Switch on Lighthead, Model SPA570Q20ON
910848 Lighting Location, On Top of the Pump Module, Rearward, Both Sides 110848 Lighting Activation, Pair, In Cab and On Pump Panel, 'LEFT SCENE' and 'RIGHT SCENE', Rocker Switches
Line Voltage Line Voltage
UPOxxxxxxx Inverter, GoWISE PS1004, 3000W
UPOxxxxxxx Transfer Switch, InvertertoShoreline
UPOxxxxxxx Inverter Location, Above Pump Module
UPOxxxxxxx Receptacle, 120V, 515R Household, Duplex, Wired to Inverter 910914 Receptacle Location, In L3 Cmpt
UPOxxxxxxx Receptacle, 120V, 515R Household, Duplex, Wired to Inverter 910914 Receptacle Location, In L3 Cmpt
110888 Cord Reel,Hannay, 120V, 200' 10/3 Yellow Cord, Terminate L530 Receptacle, Junction Box with Pigtail, Circle D
901149 Junction Box Option, Powder Coat Silver Hammertone 910860 Junction Box Receptacle, 120V, 515R Household, Duplex 910860 Junction Box Receptacle, 120V, 515R Household, Duplex 910860 Junction Box Receptacle, 120V, 515R Household, Duplex 910860 Junction Box Receptacle, 120V, 515R Household, Duplex 110908 Cord Reel Location, In Pump Module, Terminate Thru Roller Assembly on Side Pump Module, Officer's Side
Aerial Aerial
001481 Construction and Dimensions, Rear Mount Ladder Structure (105') 911154 Ladder Specifications (105')
001837 Aerial Information Specification Plate
121500 Aerial Test, NonDestructive Testing (NDT), Independent Third Party Certification
901000 Aerial Test, Structural Safety Factor, Stability Factor and Testing 911156 Rung Covers
001509 Ladder Travel Support/Cradle, Light, Cradle Interlock System (UT 100'/105'/107)
001514 Elevation System (UT 100'/105')
911166 Extension/Retraction System, Maintenance Free Sheaves (UT 100'/105'/107)
911168 Wear Pads/Bearing Surfaces
911172 Rotation System, Bearing/Gear Box/Interlocks (UT 100'/105') 911175 Cab / Body Damage Protection Interlock System
001632 Aerial Power TakeOff
001636 Hydraulic Pump with "ThruDrive" (75'/100' MMA/UT100'/105'/107) September 16, 2022 Quote #: 0022355 Page 12 of 14
Option ID Description
By: Roy Cobb, 916-677-9837 https://www.smeal.com/ Page 12 of 14 001640 Hydraulic System (UT 100'/105')
111765 Hydraulic Pressure Gauge, Rear Control Station, Inn. Cntrls, 21/2", Brass Case Gauge, psi 05000
001649 Emergency Hydraulic Pump (55'/75'/UT100'/100'MMA/105') 911194 Swivel
001805 Aerial Angle Indicator, Base Section
001807 Aerial Extension Tape
001464 Aerial Tool, Manual Rotation Drive Tool
007719 Torque Box, Painted Black, AkzoNobel #41878 (105'/107) 010207 Stabilizers, Front and Rear "H" Style, 16' Spread, Standard Stroke, WITH Stabilizer Pins (105')
911178 Stabilizer Extension System (105'/UT100'/107)
001594 Stabilizer Angle Level Gauges (2)
001603 Ground Control System, Electric Over Hydraulic Controls, Front and Rear Stabilizers, Lower Center Rear, Horizontal, Brushed Stainless Doors
001597 Stabilizer 1" Auxiliary Pads (4) with Racks Below Body Shop Note:

Mount (2) LS/RS behind rear stabilizers
007609 Stabilizer Cover Warning Lights (4), Whelen, 600 Series SuperLED (60R02FRR), Red, Activated with Aerial Master
008768 Stabilizer Arm Warning Lights (8), Whelen, 5G Series SuperLED (5GR00FRR), Red
003737 Stabilizer Work Lights (4), TruckLiteLED (81380), Clear UPOxxxxxxx Turntable, Standard (105') Bottom Walking Surface to be Black LineX Coated
008307 Turntable Handrails, Ribbed Rubber SS, Standard Turntable, (2) Openings
008344 Turntable Restraints, (2) ManSaver Bars
008037 Turntable Work Lights (4), Whelen LED, 0AC0EDCR
001614 Ladder Hour Meter, At Turntable
007390 Turntable Control Console, Painted, AL11, IC Panel, OnScene Light Under Lid (55'/75'/105'/125')
111973 System Lock Control, Red Mushroom Switch on Turntable Console 008025 Retraction Override Safety System, Switched Through AL11 007407 Load Sensing System, Programmed into AL11
008264 Load Chart (105')
008026 Communication System, 3Way, Pump PanelTurntableTip, FRC Always Clear Talking (ACT) (ICA900213)
111832 Tracking Lights (2), 12V, On Front of Cradle, FRC LED SoBrite (SRA11007A)
111842 Tracking Lights Switch, AL11
001492 Egress, BoltOn, Standard (105'/100' MMA)
007921 Ladder Creeper Controls at Tip, Switched Through AL11 (105'/125') 001505 Folding Steps on Fly Section (55'/75'/100' MMA/105'/107/125') 911157 Load Lifting/Rappelling Eyes on Fly Section
007797 Axe Mounting Bracket (1), Fly Section, WITH Flat Head Axe (FA6) September 16, 2022 Quote #: 0022355 Page 13 of 14
Option ID Description
By: Roy Cobb, 916-677-9837 https://www.smeal.com/ Page 13 of 14 111863 Tip Lights (2), 12V, FRC, LED SoBrite (SRA11007A) 911218 Tip Lights Locations, Ladder Tip, Both Sides
111883 Tip Light(s) Switch, AL11
911201 Waterway System (UT 100'/105')
007925 Positional Waterway, Switched Through AL11 (75'/100' MMA/UT 100'/105')
001713 Waterway Relief Valve / Drain Valve
111770 Flow Meter with Paddle Wheel, FRC Insight Ultimate, 4", Turntable 001717 Waterway Inlet, Rear, 4" Inlet and 4" Plumbing (UT 100'/105'/107) 101347 Valve, 4", Akron, Electric, 8940, Composite Ball, 9333 Navigator Pro Controller (Valve Only)
101250 Intake Relief Valve, Aerial, Elkhart, Factory Preset 007744 Bushing, 4" NST NH Cap (HCC2814AC), Chrome, South Park 112156 Aerial Monitor, Electric, Elkhart, Cobra EXM2 7250X2, WITH Stow Signal Output
112069 Monitor Finish, Elkhart EXM Anodized Gray
003552 Nozzle, Electric, Elkhart XStream 1250 GPM, SM1250E, 31/2" NH 911204 Monitor Sweep, Ladder, Single Monitor
911209 Master Stream Controls, Turntable and Ladder Tip 112116 Valve Under Monitor (VUM), TFT, Electric, (1) 21/2" NST Left Gated Discharge, With Drain, AKE13B181D
008326 Rope Rescue Package
111925 Rung Lighting, Blue LED (105')
111933 Rung Lighting Switch, AL11
007022 Ladder Signs (2), On Base Section
111956 Pike Pole Storage, Officer's Side Fly Section, 6' Pole 111962 Solid Beam Roof Ladder Storage, Driver's Side Fly Section, Special Width Ladder
008200 Ladder (1), DuoSafety, 16' Aluminum Roof (Special Width), 875A Paint / Striping /
Decals
Paint / Striping / Decals
900717 Chassis Paint, Chassis Manufacturer Painted, Single Tone 009165 Body Paint, Single Tone, Aerial, Aluminum Material 008907 Body Paint Color, Aerial, Single Tone, Red, AkzoNobel #32545 008794 Aerial Ladder Paint Color, White, AkzoNobel #41876, 75 RMA, 105', UT 100', 107
901036 Aerial Corrosion Protection
000968 Aerial Egress Paint, Red, AkzoNobel #32035
911225 Ladder Sign Paint, Match Aerial Ladder Structure Color 001170 Under Body Finish, TwoStep Undercoating Process 006089 Corrosion Protection, Electrolysis Corrosion Kontrol (ECK) 900875 Coating Material Technical Specification, Bedliner Coating 001033 Sample Paint Card with Paint Formula
911237 Reflective Lettering, White
004523 Rub Rail Striping, 2", Silver, Reflective, Aerial 008704 Body Striping, Aerial, 1"6"1", High Angle Transition September 16, 2022 Quote #: 0022355 Page 14 of 14
Option ID Description
By: Roy Cobb, 916-677-9837 https://www.smeal.com/ Page 14 of 14 900881 Upper Stripe Color, Black
900900 Main Stripe Color, Blue
900917 Lower Stripe Color, Black
121752 Stabilizer Beam Striping, Front and Rear, (4) Stabilizers, 4" Reflective Striping, White
900935 Chevron Color, Red / Fluorescent YellowGreen, 3M 1172EC & 3983 007383 Chevron Layout, Rear Body Surface, Torque Box Lap Door, Ladder Storage Doors
Warranties Warranties
RFW0002 General Two (2) Years or 36,000 Miles Limited Warranty RFW0502 Body Structure (Aluminum) Ten (10) Years or 100,000 Miles Limited Warranty
RFW0403 Aerial Ladder Structure Twenty (20) Years or 100,000 Miles Limited Warranty
RFW0421 Aerial LeakFree Hydraulics Three (3) Years or 48,000 Miles Limited Warranty
RFW0810 Aerial Waterway Ten (10) Years or 100,000 Miles Limited Warranty RFW0202 Electrical Two (2) Years or 36,000 Miles Limited Warranty RFW0800 Plumbing and Piping (Stainless Steel) Ten (10) Years or 100,000 Miles Limited Warranty
WLF810 Warranty, Water Tank, Pro Poly, Standard Lifetime RFW0710 Paint and Finish (Exterior Clear coated) Ten (10) Years Limited Warranty
W05810A Warranty, Pump, Waterous, Standard 7 Year

Page 1 of 122 ends

Option ID:100973 QTY:1
Smeal Branded Badging and Logo's
Smeal branded badging and Logo's shall be supplied.

Option ID:900998 QTY:1
Intent of Specifications, Aerial, Pump
INTENT OF SPECIFICATIONS
It is the intent of these specifications to cover the furnishing and delivery to the purchaser of a complete apparatus equipped as herein specified. With a view to obtaining the best results and the most acceptable apparatus for service in the fire department, these specifications cover the general requirements as to the type of construction, together with certain details as to finish, equipment, and appliances with which the successful bidder must conform. Minor details of construction and materials where not otherwise specified are left to the discretion of the contractor, who shall be solely responsible for the design and construction of all features.

Bids shall only be considered from companies that have an established reputation in the field of fire apparatus construction and have been in business for a minimum of 50 years.

Each bidder shall furnish satisfactory evidence of his ability to construct the apparatus specified. The bidder shall also show that they are in a position to render prompt service and furnish replacement parts for said apparatus.

Aerials containing load ratings and capabilities of the highest level within the respective model class shall be accepted. Bids submitted containing medium duty or light duty aerial ladders shall not be considered as meeting minimum requirements and will automatically be rejected.

CONTRACTOR'S SPECIFICATIONS
Each bid shall be accompanied by a set of "Contractor's Specifications" consisting of a detailed description of the apparatus and equipment proposed and to which the apparatus furnished under contract shall conform.

These specifications shall indicate size, type, model, and make of all component parts and equipment.

The submitted bids shall clearly describe the capabilities of the aerial device. Items such as safety factor certification, horizontal reach, vertical reach, scrub chart information, load capabilities, flow ratings, monitor capabilities, short set capabilities, safety interlock information, estimated completed weight information and other pertinent information shall be either submitted with the bid or readily available if requested.

TIMELY PROPOSALS
It is the bidder's responsibility to see that their proposals arrive on time. Late proposals, facsimiles, emails, telegram, or telephone bids shall not be considered.

DRAWINGS

Page 2 of 122 ends

A total of six (6) drawings shall be supplied. The provided drawings can be printed to any paper size, but the scale will only be valid when printed to the paper size listed in the title block
•
• Drawings shall show five (5) views: left (drivers), right (officers), front, rear, and top OAL (overall length) in feet and inches. The estimated length shall be rounded up to the nearest inch
•
OAH (overall height) in feet and inches. The estimated height shall be rounded up to the nearest inch
•
• Wheelbase in inches
• Pump house width in inches
• Front of the body to the centerline of the rear axle in inches • Front and rear overhang in inches
• Angle of approach and departure
Roll up doors will be shown in open position. Lap doors will be shown in the closed position
•
Compartment dimensions shall be shown in a table on the drawing. The table shall display
•

1. Clear door opening The width/height of the clear door opening Interior dimensions The interior compartment dimensions excluding any accessories or pockets (i.e. roll up door drums, hard suction hose pans, suspension pockets, etc.)

2. Divide heights The measurement where the compartment changes from full depth to shallow depth

3. 4. Compartment depths Depth of the compartment with the door closed Ground ladders shall be labeled with a letter designation referring to the table for an explanation of the ladder
•
No pump panel or instrument panel controls, discharges or inlets shall be shown. The panel space is to be left blank and labeled "Pump Panel" •
Rear plumbing, such as 21/2" discharges, rear steamers, and direct tank fills, shall be shown
•
• Water tank outline (if applicable)
• Water tank and foam cell fill towers (If applicable)
• Generator outline (if applicable)
• Warning lights
• D.O.T. lights
• Chassis make/model
• Fire pump make/model
• Water tank capacity (if applicable)
• Foam cell capacity (if applicable)
• Body material
• Hose bed capacity in cubic feet (if applicable)
• Total compartment cubic feet
• Utilize an unique bid number
• Drawings shall be printed on white paper with black ink All bid drawings shall be stamped PROPOSAL.

Text Block Items
PURCHASER'S OBLIGATIONS

Page 3 of 122 ends

The purchaser reserves the right to accept or reject any or all bids on such basis as the purchaser deems to be in its best interest. All bidders shall be advised that the purchaser is not bound in any manner to automatically accept the lowest bid. The purchaser shall only be obligated to purchase the lowest bid that meets these detailed specifications as closely as possible.

SPECIALIZATION
Due to the complexity of the apparatus proposed, it is the desire of the purchaser to obtain equipment that is built by companies that specialize in the construction in accordance with NFPA 1901, current edition compliant aerial devices.

The aerial device shall be engineered and fabricated by a manufacturer with a minimum of 40 years of experience in the aerial field. No exceptions shall be allowed.

No prototype devices or aerials without a proven field record shall be acceptable. The aerial device provided shall be of the highest quality available in the industry.

SAFETY REQUIREMENTS
It is required that the bidder shall meet all State and Federal safety standards and laws that are in effect on the date of the bid for the item(s) that are specified and the particular use for which they are meant.

ACQUAINTANCE WITH SPECIFICATIONS
It is the responsibility of the bidder to review all of the bidding requirements. Failure of a bidder to be acquainted with this information shall not relieve them from any obligations of the bid requirements.

QUALITY AND WORKMANSHIP
The design of the apparatus shall embody the latest approved automotive engineering practices. Experimental designs and methods shall not be acceptable.

The workmanship shall be of the highest quality in its respective field. Special consideration shall be given to the following points: accessibility of the various units that require periodic maintenance, ease of operation (including pumping and driving), and symmetrical proportions.

Construction shall be rugged and ample safety factors shall be provided to carry loads as specified.

GENERAL CONSTRUCTION
The complete apparatus, assemblies, subassemblies, component parts etc., shall be designed and constructed with due consideration to the nature and distribution of the load to be sustained and to the general character of service which the apparatus is to be subjected when placed in service.

All parts of the apparatus shall be strong enough to withstand the general service under full load. The apparatus shall be so designed that the various parts are readily accessible for lubrication, inspection, adjustment, and repair.

Page 4 of 122 ends

• NFPA 1901, Current Edition
• American Society for Testing and Materials (ATSM A36) • Society of Automotive Engineers, Inc. (SAE) "SAE Handbook" • American Welding Society (AWS) AWSO 14.477
• American Welding Society (AWS) D1.1 and D1.2
• American Society of NonDestructive Testing (ASNT) "ASNT CP189 The apparatus shall be designed and constructed, and the equipment mounted, with due consideration to the distribution of the load between the front and rear axles, and side to side loading that all specified equipment, including a full complement of specified ground ladders, full water tank, loose equipment, and firefighters; shall be carried without overloading or damaging the apparatus in accordance with NFPA 1901, current edition requirements.

LIABILITY
The bidder, if their bid is accepted, shall defend any and all suits and assume all liability for the use of any patented process, device or article forming a part of the apparatus or any appliance furnished under the contract.

WARRANTY
A copy of the warranties for the chassis, pump, body, paint, water tank (if applicable), aerial device, waterway, and waterway seals shall be furnished with each bidder's proposal.

INFORMATION REQUIRED UPON DELIVERY
The manufacturer shall supply at the time of delivery at least two copies of a complete operation and maintenance manual covering the completed aerial device as delivered.

Parts manuals, where possible, shall be crossreferenced to show the actual manufacturer's name, part number and description on all parts and fittings that are commercially available.

DESIGN / CONSTRUCTION / TESTING CRITERIA
The following criteria shall be applicable to this specification to the extent specified herein:

The aerial ladder shall be designed, fabricated, and tested in accordance with the above codes and specifications, as well as all other applicable codes, standards, and specifications that may be referenced by any of the above.

NONDESTRUCTIVE TESTING
Steel ladders, turntable, stabilizers, and torque box shall have 100% of all welds tested using both magnetic particle method and visual testing method. Aerials that are fabricated of aluminum shall have 100% of all welds tested using dye penetrant method and visual method. All testing shall be performed by certified technicians, which are employees of an independent nationally recognized and certified thirdparty testing company. Manufacturers who rely on visual inspection (either inhouse or by a third party) as the primary method of testing, and magnetic particle or dye penetrant as a secondary or "proving" test method for only suspect areas shall not be acceptable. In

Page 5 of 122 ends

any case, welds shall be tested using two (2) separate NDT inspection methods regardless of the material used to construct the aerial device.

THIRD PARTY CERTIFICATION
All bids shall include copies of the certification of testing of the aerial device. The purchaser desires a device that has been tested by a third party for compliance with the minimum 2 to 1 safety factor specified in accordance with NFPA 1901, current edition.

Devices that have not been certified by a third party engineering firm that is independent of the manufacturer shall not be acceptable, no exceptions.

AERIAL DEVICE SAFETY FACTOR AND RATED CAPACITY
The purchaser desires to purchase, using these specifications, an aerial device with a minimum 2.0:1 Safety Factor as required and defined in accordance with NFPA 1901, current edition. Therefore, the aerial manufacturer shall hereby certify, by submitting a bid for these specifications that the aerial device meets or exceeds all requirements and conditions in these specifications, no exceptions.

BID FORMS / SPECIFICATIONS
All bid forms shall be submitted on the attached bid form. The bid form and/or these specifications shall be filled out by checking either the "YES" or "NO" column for each and every section/paragraph. Failure to use this form and/or these specifications shall be cause for immediate rejection of any bid.

EXCEPTION TO SPECIFICATIONS
The following chassis, pump, and body specifications shall be strictly adhered to.

Exceptions shall be allowed if they are equal to or superior to that specified and provided, they are listed and fully explained on a separate page entitled "EXCEPTIONS TO SPECIFICATIONS". Exception lists shall refer to the specification page number.

Each check in the "NO" column shall be listed and fully explained. Where no check is made in a particular paragraph either "YES" or "NO", it shall be assumed the bidder is taking exception to that paragraph. If a paragraph contains an empty column, where the bidder neglected to check the proper "YES" or "NO" column, it is assumed the bidder is not conforming to the requirements of this paragraph. If no explanation is given in the "EXCEPTIONS TO SPECIFICATIONS" document, the bid is subject to immediate rejection.

PROPOSALS TAKING TOTAL EXCEPTION TO THESE SPECIFICATIONS WILL BE IMMEDIATELY REJECTED.

The buyer is aware that all bidders shall have to take some exceptions, therefore; BIDDERS THAT TAKE NO EXCEPTIONS shall BE REQUIRED TO MEET EVERY PARAGRAPH TO THE FULLEST EXTENT SHOULD THEIR BID BE ACCEPTED. It is the intent of the purchaser to receive bids that do not require telephone calls or other communications to ascertain what a bidder is intending to supply.

Upon delivery, the apparatus shall be inspected against these specifications and not those supplied by the bidder with their proposal. Deviations shall not be acceptable unless noted as exceptions at the time of bid. The apparatus shall be rejected until said deviations are corrected to the satisfaction of the buyer.

Page 6 of 122 ends

• Accelerating from 0 to 35 mph within 25 seconds on a 0 percent grade • Attaining a speed of 50 mph on 0 percent grade
• Maintaining a speed of at least 20 mph on any grade up to and including 6 percent The maximum top speed of the apparatus shall not exceed the tire manufacturer's maximum speed rating for the tires installed on the apparatus •
Decisions regarding equal to or better than shall be the sole responsibility of the recipient of the bids rather than companies submitting bids. All deviations, regardless of significance, must be explained in the "EXCEPTIONS TO SPECIFICATIONS" section of the bid.

When exceptions are not taken but inconsistencies are noted in the submitted detailed specifications, the bid may be rejected.

ROADABILITY
The apparatus, when fully equipped and loaded, shall be capable of the following performance while on dry paved roads that are in good condition:

FAILURE TO MEET TESTS
In the event the apparatus fails to meet the test requirements of these specifications on the first trials, second trials may be made at the option of the bidder within 30 days of the date of the first trials.

Such trials shall be final and conclusive and failure to comply with these requirements shall be cause for rejection. Failure to comply with changes as required to conform to any clause of the specifications within 30 days after notice is given to the bidder of such changes, shall be cause for rejection of the apparatus.

Permission to keep or store the apparatus in any building owned or occupied by the department during the specified period, with the permission of the bidder, shall not constitute acceptance.

PROPOSAL SEQUENCE
Bid specifications shall be submitted in the same sequence as these specifications for ease of checking compliance. No exceptions shall be allowed to this requirement. The apparatus committee intends to be thorough during the evaluation of bids process. In order to maximize efficiency and minimize time to thoroughly evaluate all received bids, this requirement must be strictly enforced.

AWARD OF CONTRACT
All bids submitted shall be valid for a minimum of 30 days during which time bid securities submitted with the proposals shall be held by the purchaser. Criteria for the award shall include, but not be limited to, the following:

Page 7 of 122 ends

• Apparatus Performance And Safety Levels / Considerations • Completeness of proposal
• Accuracy of accompanying data
• Past performance of bidder
• Compliance with the detailed specifications
• Compliance with purchasers request(s) for personnel qualifications or certifications • Exceptions and clarifications
• Financial stability of bidder
• Local representation of the manufacturer
• Serviceability of the proposed apparatus
• Service capabilities of the bidder's local representative • Compliance with NFPA 1901, current edition
• Any other factor the purchaser deems relevant
After the evaluation and award process is complete, all bidders shall be notified of the results and securities shall be returned.

The manufacturer of the apparatus herein specified, shall be wholly owned (100%) and managed by a Company, Corporation, and/or Parent Company that is wholly based and permanently resides in the United States of America. •
The Company, Corporation, and/or Parent Company, and all assets belonging to such, shall be wholly owned and managed (100%) by the entities specified above. •
Option ID:911059 QTY:1
Bidding Prerequisites, United States
PREREQUISITE BIDDING REQUIREMENTS
Any manufacturer submitting a proposal or bid, to these specifications, shall meet the following conditions:

Any proposal, bid, or response to these specifications by any foreign based, owned, or managed (in part or in whole) Company, Corporation, and/or Parent Company shall be cause for immediate rejection. Any proposal, bid, or response to these specifications by any Company, Corporation, and/or Parent Company, that is owned, operated, managed, or held in contract, in part or wholly by a partnership or other agreement, shall be cause for immediate rejection.

Exceptions to these conditions will not be allowed under any circumstances.

Option ID:911060 QTY:1
Standards Version, NFPA 19012016
NFPA 19012016
The National Fire Protection Association "Standard for Automotive Fire Apparatus", 2016 edition, is hereby adopted and made a part of these specifications, the same as if it were written out in full detail, with the exception of the section dealing with "Equipment Recommended for Various Types of Apparatus". Bidders shall provide the equipment requested herein and the buyer shall supply the rest before the apparatus is put into service. It is the intent of the purchaser to purchase an apparatus that meets 100% of the minimum standards defined and outlined in NFPA 19012016 edition. There are to be no exceptions to this requirement.

Page 8 of 122 ends

Ensure that understanding of all parties respective responsibilities have been addressed by the actual referencing of NFPA 1901 and the amendments in these specifications and the purchase contract and documentation. •
Ensure that only structural materials complying with appropriate standards and codes are used for construction.
•
Ensure the applicable standards of design and manufacturing have been met or exceeded.
•
• Ensure that safety factors have been met or exceeded where required.

Ensure that applicable standards for testing and inspection have been met or exceeded by personnel with the appropriate qualifications, experience, and certifications.
•
Ensure that where applicable components, equipment, and loose equipment carry the appropriate characteristics, classifications, and/or certifications. •
Ensure that in general and as a whole, all applicable requirements set forth in NFPA 1901, and those codes, standards, and specifications referenced by said parties are met, exceeded, and/or addressed.
•
Option ID:911064 QTY:1
Inspection Certificate, NFPA 1901 Compliance
INSPECTION CERTIFICATE NFPA 1901 COMPLIANCE
An OEM inspection certificate for the apparatus shall be furnished upon delivery. The purpose of this NFPA 1901 compliance inspection shall be to serve as proof to the customer that all applicable standards have been met or exceeded by the responsible manufacturer.

The following objectives shall be achieved as a result (this listing shall not be construed as being all inclusive):

Option ID:911070 QTY:1
Documentation, NFPA
CONSTRUCTION DOCUMENTATION
The contractor shall supply, at the time of delivery, at least one (1) copy of the following documents:

1. The manufacturer's record of apparatus construction details, including the following information:

Page 9 of 122 ends

• Owners name and address
• Apparatus manufacturer, model, and serial number
• Chassis make, model, and serial number
• GAWR of front and rear axles
• Front tire size and total rated capacity in pounds or kilograms • Rear tire size and total rated capacity in pounds or kilograms Chassis weight distribution in pounds with water and manufacturer mounted equipment (front and rear)
•
Engine make, model, serial number, rated horsepower, related speed, and governed speed
•
• Type of fuel and fuel tank capacity
• Electrical system voltage and alternator output in amps • Battery make, model, and capacity in cold cranking amps (CCA) Chassis transmission make, model, and serial number; and if so equipped, chassis transmission PTO(s) make, model, and gear ratio
•
If applicable, the pump make, model, rated capacity in gallons or liters per minute, and serial number
•
Pump transmission make, model, serial number, and gear ratio, if unit is equipped with a pump
•
If applicable, the auxiliary pump make, model, rated capacity in gallons or liters per minute, and serial number
•
• Water tank certified capacity in gallons or liters
On aerial apparatus, the device type, rated vertical height in feet or meters, rated horizontal reach in feet or meters, and rated capacity in pounds or kilograms •
• Paint manufacturer and paint number(s)
• Company name and signature of responsible company representative

2. Certification of slip resistance of all stepping, standing, and walking surfaces

3. If the apparatus has a fire pump, a copy of the following shall be provided: pump manufacturers certification of suction capability, apparatus manufacturers approval for stationary pumping applications, engine manufacturers certified brake horsepower curve showing the maximum governed speed, pump manufacturers certification of the hydrostatic test, and the certification of inspection and test for the fire pump

4. If the apparatus has an aerial device, the certification of inspection and test for the aerial device, and all the technical information required for inspections to comply with NFPA 1914, Standard for Testing Fire Department Aerial Devices

5. If the apparatus has a fixed line voltage power source, the certification of the test for the fixed power source

6. If the apparatus is equipped with an air system, test results of the air quality, the SCBA fill station, and the air system installation

7. Weight documents from a certified scale showing actual loading on the front axle, rear axle(s), and overall fire apparatus (with the water tank full but without personnel, equipment, and hose)

8. Written load analysis and results of the electrical system performance tests

9. When the apparatus is equipped with a water tank, the certification of water tank

Page 10 of 122 ends

• Manufacturers name and address
• Country of manufacturer
• Source of service and technical information
• Parts and replacement information
• Descriptions, specifications, and ratings of the chassis, pump, and aerial device Wiring diagrams for low voltage and line voltage systems to include the following information: representations of circuit logic for all electrical components and wiring, circuit identification, connector pin identification, zone location of electrical components, safety interlocks, alternatorbattery power distribution circuits, and input/ output assignment sheets or equivalent circuit logic implemented in multiplexing systems
•
• Lubrication charts
Operating instructions for the chassis, any major components such as a pump or aerial device, and any auxiliary systems
•
• Precautions related to multiple configurations of aerial devices, if applicable • Instructions regarding the frequency and procedure for recommended maintenance • Overall apparatus operating instructions
• Safety considerations
• Limitations of use
• Inspection procedures
• Recommended service procedures
• Troubleshooting guide
• Apparatus body, chassis, and other component manufacturers warranties • Special data required by this standard
Copies of required manufacturer test data or reports, manufacturer certifications, and independent thirdparty certifications of test results
•
A material safety data sheet (MSDS) for any fluid that is specified for use on the apparatus
•
• One (1) copy of the FAMA Safety Guide
capacity
OPERATION AND SERVICE DOCUMENTATION
The contractor shall supply at the time of delivery, at least two (2) sets of complete operation and service documentation covering the completed apparatus as delivered and accepted. The documentation shall address at least the inspection, service, and operations of the fire apparatus and all major components thereof. The contractor shall also provide documentation of the following items for the entire apparatus and each major operating system or major component of the apparatus:

The contractor shall deliver with the apparatus all manufacturers operations and service documents supplied with components and equipment that are installed or supplied by the contractor.

STATEMENT OF EXCEPTIONS
The proposed apparatus as described in this specification document and all related material with the bid package shall meet or exceed all applicable sections for the category of apparatus as defined by NFPA 1901 unless specifically noted within this specification or other official documents associated with this bid.

Should any area, section or portion of the apparatus not meet the intent and applicable

Page 11 of 122 ends

Dinuba City CouncilMarch 28, 2023

Dinuba City Council
March 28, 2023