Hemet City Council
October 25, 2022

15.A

Account # 115-3241-5400

Total= $312,024.91

ATTACHMENT(S):

Attachment 1: Revised Quote Spec for Hemet Patrol 9-22
Attachment 2: Hemet Patrol Sales Drawing 9-22
Attachment 3: BME Form E Published Options June 2022 web Attachment 4: Authorized-Dealer-Distributor-BME Contract #FS12-19-South Coast Fire Equipment, Inc
Attachment 5: Amendment 2 contract extension-Boise Mobile Equipment, Inc FS12-19 Attachment 6: FS12-19 Final
Attachment 7: HGAC FS12-19 9-22 Hemet
Attachment 8: Medic PatrolType VI Resolution 10-2022

15.A

Boise Mobile Equipment
08/30/22
1 City of Hemet, California
Type-6 Medic Patrol

DETERMINATION OF APPARATUS WEIGHT
Boise Mobile Equipment, Inc shall submit estimated "in-service" weight analysis required by applicable NFPA standards. This Excel computer weight analysis shall break down all major components of the apparatus and shall show the impact on percentage-of-load on the front and rear axles, total weight, and weight on each tire set.

The analysis shall evenly distribute the NFPA required minimum payload allowance or estimated equipment payload as provided by the purchaser into the specified compartments. The allowance for personnel, hose loads, water and foam fluids, and required NFPA equipment shall be outlined individually in the analysis and placed on the apparatus in its specific intended position.

CENTER-OF-GRAVITY ANALYSIS
Boise Mobile Equipment, Inc shall perform an estimated center of gravity calculation as required by the

15.A

Boise Mobile Equipment
08/30/22
2 applicable section of NFPA standards. This calculation shall include tilt angles, the estimated right to left load distribution, and load on each axle, including all specified major components.

ELECTRICAL LOAD ANALYSIS
A 12 volt electrical load analysis shall be completed as required by the purchaser.

NFPA COMPLIANCE
The fire apparatus shall be in full compliance to the most current edition of NFPA #1901/1906 except when stated otherwise and as accepted by the customer.

THIRD PARTY FIRE PUMP TESTING
A Boise Mobile Equipment, Inc facility shall be used for testing the fire pump system by Underwriters Laboratories, Inc. The pump test shall be witnessed and certified per applicable sections of NFPA standards, prior to delivery of the completed apparatus. The UL acceptance certificate shall be furnished with required delivery documentation.
12 VOLT ELECTRICAL TESTING
The completed fire apparatus shall undergo a complete 12 volt electrical load and performance testing per applicable sections of NFPA standards with inspection and test sheets included in delivery documentation.

TEST RESULTS
Boise Mobile Equipment Inc. shall provide results of the apparatus testing and shall certify the following:

The weight of the completed apparatus, when loaded to it’s estimated in service weight, does not exceed the GVWR and GAWR of the chassis.

The complete unit, when loaded to its estimated in service weight, meets the weight distribution and vehicle stability requirements, as defined in the current NFPA guidelines.

The unit meets all required federal standards pertaining to the manufacturer and completion of the apparatus and a label tag has been affixed to the apparatus by the manufacturer stating same.

Boise Mobile Equipment Inc. shall provide all testing results, including engine, speed, acceleration, road ability, braking, and auxiliary braking to the Purchaser at the time of delivery.

MATERIAL AND WORKMANSHIP

15.A

Boise Mobile Equipment
08/30/22
3 All equipment provided shall be guaranteed to be new and of current manufacture, and unless specified otherwise, shall meet all requirements of these specifications and prevailing NFPA documents and be in condition at time of delivery for use as specified for this type of apparatus.

All workmanship shall be of the highest quality and accomplished in a professional manner so as to insure a functional apparatus with a high quality aesthetic appearance.

The construction shall be rugged and ample safety factors shall be provided to carry the loads specified to meet both on and off road requirements.

The apparatus shall be designed and the equipment mounted with due consideration to the distribution of load between the front and rear axles, so all specified equipment, with a full complement of personnel, can be carried without damage to the apparatus.

FOAM TANK WARRANTY
The foam tank shall carry a “lifetime” warranty against defects in workmanship and perforation corrosion. The provisions of this warranty shall be provided in the delivery documentation.

PAINT WARRANTY
Boise Mobile Equipment, Inc shall provide a seven (7) year paint warranty which shall cover peeling and/or de-lamination of the top coat and other layers of paint, cracking or checking, loss of gloss caused by cracking, checking or chalking, and any paint failure caused by defective paint materials covered by the paint manufacturer’s material warranty.

CHASSIS WARRANTY
The specified chassis shall be provided with the chassis manufacturer's warranty. The exact provisions of this warranty shall be supplied with the completed apparatus documentation.

CHASSIS OPERATION MANUALS
The apparatus delivery documentation furnished by Boise Mobile Equipment shall include one (1) printed custom chassis manufacturer's operational manual(s).

APPARATUS OPERATION MANUAL(S)
Boise Mobile Equipment shall provide one (1) USB manual.

BODY AND STRUCTURAL WARRANTY

15.A

Boise Mobile Equipment
08/30/22
4 Boise Mobile Equipment shall warrant each new apparatus body, if used in a normal and reasonable manner, against structural defects caused by defects in material, design or workmanship for a period of ten (10) years, covering parts & labor to the original purchaser which shall start on day of acceptance.

This warranty shall not apply to:
· Normal maintenance services or adjustments
· To any vehicle which will have been repaired or altered outside of our factory in any way so as, in the judgment of BME, to affect it's stability, nor which has been subject to misuse, negligence, or accident, nor to any vehicle made by us which will have been operated to a speed exceeding the factory rated speed, or loaded beyond the factory rated load capacity. · Commercial chassis and associated equipment furnished with chassis, signaling devices, generators, batteries, or other trade accessories as they are usually warranted separately by their respective manufacturers.
· Shipping costs of parts or apparatus for purposes of repair or replacement of parts. This warranty is in lieu of all other warranties, expressed or implied. All other representations as to the original purchaser and all other obligations or liabilities, including for incidental or consequential damage on the company's behalf unless made in writing by the company.

DARLEY FIRE PUMP WARRANTY
A three (3) year warranty on the Darley fire pump shall be provided. The provisions of this warranty shall be described in the completed apparatus documentation.

PLUMBING WARRANTY
The stainless steel fire pump plumbing shall carry a ten (10) year parts and labor warranty against defects in workmanship and perforation corrosion.

AKRON VALVE WARRANTY
The Akron valves shall carry a ten (10) year parts and labor manufacturer’s warranty. Provisions of this warranty shall be provided with the completed apparatus documentation.

WATER TANK WARRANTY
The polypropylene water tank that is specified to be supplied with this apparatus shall be warranted by the water tank manufacturer for a "lifetime" period from the date that the apparatus is put into service. The tank

15.A

Boise Mobile Equipment
08/30/22
5 manufacturer shall repair, at no cost to the purchaser, any problems caused by defective materials and/or workmanship. The warranty shall cover the reasonable costs of removing the water tank from the apparatus and reinstalling it after the completion of the covered warranty repairs, but shall not cover any liability for the loss of service or downtime costs of the apparatus.

FOAM TANK WARRANTY
The foam tank shall carry a “lifetime” warranty against defects in workmanship and perforation corrosion. The provisions of this warranty shall be provided in the delivery documentation.

CHASSIS SPECIFICATIONS
One (1) 2023 Diesel Ford F- 550, 4x4, Crew Cab XLT
Cab Type: 4-Door Crew Cab
Wheelbase: 179"
Cab to Axle: 60"
GVWR: 19,000 pounds
Engine: 6.7L Power Stroke Turbo Diesel
Factory exhaust brake
Ten speed Automatic

4.30 Limited Slip Axle
Trailer Tow Package-High Capacity
Power Equipment Group
Extra Heavy Duty Front-End Suspension
Details To Follow:

19.5" Argent Painted Steel Wheels
• Privacy Glass
• Front Wheel Well Liner

15.A

Boise Mobile Equipment
08/30/22
6 • Transmission Power Take-Off Provision
• Skid Plates – Transfer Case
• Exterior Backup Alarm
• Alternator – 332 Amp Dual
• 225/70Rx19.5G BSW A/P Tire
• Manually Telescoping/Folding Trailer Tow with Power/Heated Glass, Heated Convex Spotter Mirror, Integrated Clearance Lamps/Turn Signals Interior
Medium Earth Gray Cloth, 40/20/40 Split Bench, 20% Center Under-Seat Storage, w/Center Armrest, Cupholder and Storage, Four-way Adjustable Driver/Passenger Headrests, Manual Lumbar Seats • Carpet Delete
• Bluetooth
• Cruise Control
• Trailer Brake Controller
• 110V/400W Outlet
• Up fitter Interface Module
• AM/FM Stereo MP3 Player
• SiriusXM RadioSYNC3 Tow Package - High Capacity
• Power Equipment Group

XLT TRIM PACKAGE
The chassis to be equipped with the Ford XLT trim package. This trim package typically includes the following options.
- Bluetooth
- Cruise Control
- Black door handles
- Dual beam jewel effect headlamps
- Rear fixed window
- Solar tinted windows
- Black vinyl floor covering
- Tilt/telescoping steering wheel
- Door trim with armrest, grab handle, and reflector
- Vinyl sun visors: single driver with pocket, single passenger with mirror insert - Interval control windshield wipers
-Dual Sun visors
- Two (2) speed Electric Windshield Wipers, with intermittent control - Dome Light
- Fresh Air Heater and Defroster
- Dual Electric Horns
- Driver and Passenger Air Bags
-The cab grille to be a black high impact plastic with a horizontal/vertical channel design. -The mirrors to be black, power, foldaway type. The heated mirror face to be power controlled, and the mirror head to manually telescope in/out for view adjustment.

CAB SEATING AND WEIGHT ALLOWANCE

15.A

Boise Mobile Equipment
08/30/22
7 A warning label shall be installed in the cab to indicate seating positions for five (5) people. A weight allowance of 250 pounds shall be calculated for each person.

DATA PLAQUE
A data plaque shall be provided and installed on the inside of driver's door. The data plaque shall contain the required information based on the applicable components for the apparatus:
· Engine oil
· Engine coolant
· Chassis transmission fluid
· Drive axle lubricant
· Power steering fluid
· Pump, generator, or other component lubrications
· Other NFPA applicable fluid levels or data as required · Paint manufacturer, type, and color number
· Tire Speed Ratings
Location shall be in the driver's compartment or on driver's door.

DIMENSION DATA LABEL
The cab dash area shall have an apparatus dimension label installed. The label shall be highly visible, indicating the overall height, length, width and weight of the vehicle.

WARNING LABEL -- NO RIDING ON REAR
A warning label stating: "NO RIDING ON REAR OF APPARATUS" shall be installed on rear of the apparatus.

The label shall be applied to the vehicle at the rear step area. The label shall warn personnel that riding in or on these areas, while the vehicle is in motion, are prohibited.

WARNING LABEL -- SEAT BELT USEAGE
A warning label, stating: "DANGER- Personnel Must Be Seated And Seat Belts Must Be Fastened While Vehicle Is In Motion Or DEATH OR SERIOUS INJURY MAY RESULT" shall be provided in the apparatus cab interior. This label shall be located so that it is visible from all seating positions.

VEHICLE FINAL STAGE MANUFACTURER LABEL
A final stage manufacturer label shall be installed by the fire apparatus body manufacturer in compliance with applicable motor vehicle standards.

15.A

Boise Mobile Equipment
08/30/22
8 MANUFACTURER LOGO
The apparatus shall include a Boise Mobile Equipment logo plaque which shall be affixed at the rear of the apparatus.

FRONT TOWING PROVISIONS
Two (2) front towing provisions shall be installed by the chassis manufacturer with a min imum rating of 5000# each.

REAR TOW PLATES
Two (2) painted bolt-on tow plates shall be installed at the rear of the chassis.

EXHAUST TIP
Provide a 4" exhaust tip compatible with the Department station Plymovent exhaust evacuation system.

REAR MUD FLAPS
The chassis shall be supplied with mud flaps with the manufacturer's logo. The mud flaps shall be installed behind the rear wheels.

CAB DOOR REFLECTIVE PANELS
The cab doors shall include black reflective trim installed inside each door. *** Auxiliary Lighting ***

AUXILIARY OFF ROAD LIGHT
There shall be two PIAA 560 LED driving lights installed inset on the front bumper face. location to be determined at pre-construction meeting.

AUXILIARY OFF ROAD LIGHT
There shall be a Rigid Industries, E 20" combo Spot / Flood LED light, model #120313 provided and installed.

A switch control shall be provided on the dash, labeled "AUXILIARY LIGHTS, OFF HIGHWAY USE ONLY".

Exact location shall be determined at the pre-construction meeting.

15.A

Boise Mobile Equipment
08/30/22
9 The scene lights shall be activated by individual buttons or switches on the cab center console. Left, right, and rear scene light controls.

AIR FILTER EMBER PROTECTION SCREEN AND WARNING LABEL
An ember protection screen and warning label, stating: “This apparatus is equipped with an air filter ember protection screen; routine inspection is required,” shall be provided and installed in the apparatus cab interior.

This label shall be located so that it is visible from the driver’s seating position.

AIR FILTER EMBER PROTECTION SCREEN WARNING LABEL
A warning label, stating: “This apparatus is equipped with an air filter ember protection screen; routine inspection is required,” shall be provided and installed in the apparatus cab interior.

EMBER SEPARATOR -- FRESH AIR INTAKE TO CAB
The cabin air filter shall be protected by an ember guard with a maximum mesh opening of 0.039 inches.

EMBER SEPARATOR WARNING LABEL
A final stage manufacturer shall install an applicable warning label for cleaning the NFPA required ember separator screen.

TIRE PRESSURE INDICATOR SYSTEM
There shall be a tire pressure indicator at each tire's valve stem on the vehicle that shall indicate if there is insufficient pressure in the specific tire. This shall be the OEM TPMS.

PORTABLE PUMP
A Darley 1-1/2AGE 24K high pressure portable pump shall be provided on the apparatus. The unit shall have a liquid cooled, 24 HP, Kubota D902 diesel engine equipped with an electric start.

Pump Performance
120 gpm @ 150 psi
75 gpm @ 245 psi
25 gpm @ 375 psi
Diesel Engine
Kubota, D902 Diesel, water-cooled, 24 hp.

15.A

Boise Mobile Equipment
08/30/22
10 Fuel Supply
The engine shall be piped to the chassis fuel system with provisions to prevent fuel drain back to the tank when the engine is shutdown.

Fuel Prime
A fuel re-prime pump shall be provided to assist in fuel delivery to the diesel engine from the chassis tank.

Lubrication
Pressure feed with spin-on filter.

Starter
12-volt electric wired into the chassis battery system
Exhaust
A spark arrestor shall be provided on the engine exhaust system.

Air Intake
An air cleaner shall be provided with easy access to remove the element.

An ember screen shall be provided on the inlet to the air cleaner.

DUAL DARLEY DELUXE PANELS
The auxiliary pump shall be controlled by a dual Darley, Deluxe panel set up. One panel shall be located on the pump panel and one panel shall be located in the cab console.

SKID PUMP PLUMBING- GENERAL
The plumbing system shall utilize stainless steel piping incorporating hosing to allow for flex. The piping shall utilize TIG welding to provide a complete seal. Hard angles shall be avoided when possible to improve water flow characteristics. The piping shall utilize Victaulic couplers whenever possible to allow flex as the body module flexes.

Threaded sections of piping shall be avoided to reduce the leak potential of the system. Victaulic couplers shall be used in place of threading to reduce leak potential. Schedule 10 stainless steel piping shall be used for transport type piping. Schedule 40 stainless steel shall be used for areas requiring threading to provide a stable threading base. Brackets shall be installed to support threading locations thereby reducing the potential for leaks.

All hoses shall be connected directly to the tank due to the different flex ratios of the tank to body. Any front discharges, any rear discharges, and all cross lays shall use hose to reach the actual discharge. The use of hose shall be utilized due to the difference in flex or movement between the discharge location and the pump connection. Drain lines shall be provided at the lowest points in the plumbing system to allow for complete drainage. Bleeders shall be provided for all gauges to relieve pressure after use.

15.A

Boise Mobile Equipment
08/30/22
11 All piping shall be hydrostatically tested to assure structural integrity in accordance with NFPA standards, with the test results submitted to purchaser upon delivery.

AUXILIARY PUMP EXHAUST SYSTEM
The auxiliary fire pump and engine assembly shall have a muffler and exhaust pipe. The exhaust pipe shall be directed out of the compartment and away from the pump operator. An additional guard shall be installed where the pipe is exposed to touch by an operator.

PRIMER ASSEMBLY
There shall be an electric primer assembly shall be installed for the auxiliary fire pump. The electric primer assembly shall be capable of taking suction and discharging water with a lift of 10 feet in not more than 30 seconds with the pump dry, through 20 feet of suction hose of appropriate size. A high capacity, electrically driven rotary vane priming pump shall be provided.

LOW PRESSURE PUMP SHUT-DOWN
If the fire pump runs out of water and the pressure decreases to zero, an automatic pressure switch shall detect the condition, and after 1 minute the device shall turn off the fire pump operation.

LOW OIL PRESSURE / HIGH TEMPERATURE PUMP SHUT-DOWN
If the fire pump has low oil pressure or high engine temperature, automatic pressure switches shall detect the condition, and the device shall turn off the fire pump operation. There shall be an override switch provided and installed on the operators pump panel to allow the system to be disabled when required.

AUXILIARY FUEL SYSTEM
The fuel system for the auxiliary fire pump shall be plumbed to the chassis fuel system. There shall be a separate fuel pickup tube mounted in the chassis fuel tank specifically for a separate engine driven pump assembly utilizing 3//4 fuel supply only. There shall be an electric fuel pump with regulator and fuel hose furnished between the chassis fuel tank and the auxiliary pump.

AUXILIARY FIRE PUMP ELECTRIC START WIRING TO CHASSIS
Properly sized 12 volt positive and negative cables shall be provided from the chassis battery to the auxiliary fire pump.

AUXILIARY PUMP WARNING AND INSTRUCTION LABELS

15.A

Boise Mobile Equipment
08/30/22
12 The auxiliary fire pump installation shall have operating instruction and warnings as required by applicable sections of NFPA standards on the pump panel or in the cab.

MASTER PUMP DRAIN
One (1) Trident, multiple-port drain valve, fabricated from bronze, shall be provided and controlled at the pump operator’s control panel. The valve shall be opened by turning a rotary hand wheel. The valve shall be plumbed to drain both the discharge and intake sides of the pump, the relief valve and other plumbing components as required.

The valve shall be placed as low as possible to provide proper drainage of the components plumbed to it. The valve shall be rated to 600 PSI minimum and suitable for daily valve actuation.

WATER TANK SUPPLY LINE TO FIRE PUMP
A 2.5" water tank to pump line shall be installed with a 2.5" full flow quarter turn ball valve and 2.5" piping.

The line shall be equipped with a hump hose with stainless steel hose clamps and check valve to tank.

The valve shall be equipped with a Innovative Controls manually operated pull rod, with quarter-turn locking feature.

COOLING LINE
A 1/4" pump to tank direct cooling line shall be provided with an in-line check valve to prevent backflow and allow priming. There shall be no valve to control this line. It shall flow water whenever the pump is running. 80 DEGREE FAN SWIVELING NOZZLES
Ground sweeps shall be provided on the front bumper, one (1) nozzle per side - two (2) total. The system shall have a manually operated 1" isolation valve located at the rear pump area. The system will be plumbed to the front bumper using 1" flexible hose. At the bumper, two (2) 12-volt solenoid operated valves shall be provided with a control switch in the cab to start and stop sweep flow at each side. The system shall terminate in two (2) 3/4" Elkhart cone spray nozzles with adjustable flow and pattern, one (1) on each side of the truck.

The specified front spray nozzles shall both be controlled togehter as a pair with one console mounted switch labeled "front sprayers"
1-1/2” DISCHARGE -- REAR
One (1) 1-1/2" discharge shall be installed on the rear of apparatus, controlled by a direct control quarter turn ball valve. The discharge shall have 1-1/2" pipe and valve x 1-1/2" NH male hose threads and cap and nameplate label adjacent the valve control handle.

15.A

Boise Mobile Equipment
08/30/22
13 One (1) Akron 8815 series swing-out style valve(s) shall be supplied and installed. All valves shall be designed to operate under normal conditions up to 500 PSI and shall have dual seats to work in both pressure and vacuum environments. All valves and controls shall be easily accessible for service, repair or replacement.

The specified valve shall have a direct actuated ‘local’ control Akron Model TSC valve handle.

The Class A foam system shall be piped to the specified discharge. 3/4” GHT DISCHARGE
One (1) 3/4" discharge shall be installed on the rear pump control panel, controlled by a quarter turn ball valve on pump panel. The discharge shall have 3/4" male garden hose threads and nameplate label adjacent the valve control handle.

One (1) Class-1 or equal 1/4 turn full flow brass ball valve with hand knob control shall be provides.

The Class A foam system shall be piped to the specified discharge.

HOSE BED PRE-CONNECT - DRIVERS SIDE
A 1-1/2" hose bed pre-connect shall be installed front to rear over the driver’s side compartments. One (1) Akron 8815 series swing-out style valve(s) shall be supplied and installed. All valves shall be designed to operate under normal conditions up to 500 PSI and shall have dual seats to work in both pressure and vacuum environments. All valves and controls shall be easily accessible for service, repair or replacement. The valve shall be equipped with an Innovative Controls manually operated pull rod at the pump panel, with quarter-turn locking feature and 2-1/2" pressure gauge in a common bezel. One (1) chrome plated brass 1.5" NH rocker lug cap with a securing chain or cable shall be installed on the discharge. Hose connection location within hose bed TBD by HFD at “Pre-Con” meeting.

One (1) Akron 8815 series swing-out style valve(s) shall be supplied and installed. All valves shall be designed to operate under normal conditions up to 500 PSI and shall have dual seats to work in both pressure and vacuum environments. All valves and controls shall be easily accessible for service, repair or replacement.

The Class A foam system shall be piped to the specified discharge. 1-1/2" BUMPER AREA DISCHARGE
Two (2) 1-1/2" discharge with 1-1/2" quarter turn ball valve with (1) pre-plumbed 90-degree swivel elbow discharge on each driver and passenger corner. Each discharge will have its own on/off control valve in the bumper with ease of access.

15.A

Boise Mobile Equipment
08/30/22
14 Two (2) Akron 8815 series swing-out style valve(s) shall be supplied and installed. All valves shall be designed to operate under normal conditions up to 500 PSI and shall have dual seats to work in both pressure and vacuum environments. All valves and controls shall be easily accessible for service, repair or replacement.

The valve shall be equipped with an Innovative Controls manually operated pull rod at the pump panel, with quarter-turn locking feature and 2-1/2" pressure gauge in a common bezel.

One (1) chrome plated brass 1.5" NH rocker lug cap with a securing chain or cable shall be installed on the discharge.

The Class A foam system shall be piped to the specified discharge.

HOSE REEL
One (1) Hannay #SBEF16.5-30-31 aluminum hose reel shall be installed. The reel shall have leak proof ball bearing swing joint, adjustable friction brake, electric 12 volt rewind and manual crank rewind provisions. The reel shall be plumbed with wire reinforced, high-pressure hose coupled with brass fittings. The reel shall be designed to hold 125% of the specified hose capacity.

The reel shall be provided with a 12 volt electric motor of appropriate size for rewinding. The hose reel shall have provisions for being rewound manually. The pinion shaft for the manual rewind gear shall be equipped with an adjustable tension brake, controlled at the hose reel.

The reel shall be mounted in the driver side rear of the body behind the pump control panel. A 4 sided captured hose roller asssembly shall be provided for the hose to exit the rear of the vehicle.

The reel shall not protrude above the apparatus body.

The reel shall be mounted in the rear compartment.

HOSE REEL DISCHARGE
One (1) 1" discharge shall be piped from the fire pump to the hose reel with flexible high pressure hose. The quarter turn ball valve shall be controlled on pump panel. A nameplate label shall be provided near the valve control handle.

One (1) Akron 8810 series swing-out style valve(s) shall be supplied and installed. All valves shall be designed to operate under normal conditions up to 500 PSI and shall have dual seats to work in both pressure and vacuum environments. All valves and controls shall be easily accessible for service, repair or replacement.

15.A

Boise Mobile Equipment
08/30/22
15 The valve shall be equipped with a Innovative Controls manually operated pull rod, with quarter-turn locking feature.

The Class A foam system shall be piped to the specified discharge.

One (1) push button hose reel rewind control shall be installed on the pump panel.

REEL MOUNTED HOSE
Three (3) 50' foot lengths of 1" water hose shall be installed on the hose reel. The hose shall be equipped with chrome plated pin lug couplings and have an 800 PSI working pressure.

AROUND-THE-PUMP CLASS A FOAM SYSTEM
A Trident Emergency Products Foamate ATP 1.0 around-the-pump foam system shall be installed. It shall be capable of mixing Class A foam concentrate with water. The system shall have a panel mounted metering control. Foam concentrate flow rates through the metering valves shall be user controlled to provide the correct amount of concentrate at the nozzle. The system shall be installed in a water by-pass loop between the pump intake and pump discharge. The flow in this around-the-pump loop shall create suction to draw the foam concentrate into the metering control, mix it with the water, and inject it into the intake side of the pump.

The system shall provide the following features and capabilities:

Desired injection rate selector
Nozzle flow selector
Foam ON -OFF control
Operation Instructions
Class A
Foam concentrate induction rate: 1 GPM maximum
Discharge flow rate: Up to 400 GPM
Proportioning ratio: 1/4 %, 1/2 %, and 1 %

PUMP AREA COVER DOOR
Provide a forward hinged one-piece treadplate cover ove the pump and plumbing space. The cover shall lift up from the rear of the vehicle while standing on the step bumper. Louvered openings shall promote cooling airflow for the pump when running. The door shall utilize gas struts to hold open with an aluminum 2" x 2" x 3/16" square tube support frame. The pump module cover shall be provided with one (1) TecNiq E-10 light. The light shall activate when the door is opened the door shall be wired to the door ajar. The door shall be black duracoated aluminum treadplate and support a minimum of 250lbs each when closed.

PUMP PANEL

15.A

Boise Mobile Equipment
08/30/22
16 The pump panel shall be constructed of 14 gauge #304 matte black powder coat stainless steel bolted to the pump enclosure with stainless steel fasteners.

Pump panel shall be equal to the rear body cargo space opening dimensions with an aluminum square tube support structure.

MASTER PRESURE GAUGES
There shall be one (1) Innovative Controls 3.5” diameter 0-300 PSI master pressure gauge mounted on the pump control panel.

WATER TANK GAUGE
One (1) Fire Research TankVision model WLA300-A00 tank gauge shall be installed on the pump panel. The water tank indicator kit shall include an electronic indicator module, a pressure sensor, and a 10' sensor cable.

The indicator shall show the volume of water in the tank on nine (9) easy to see super bright LEDs.

CAB MOUNTED -- WATER TANK GAUGE
One (1) Fire Research brand mini tank level gauge, shall be provided on the cab center console matching the panel gauge. The gauge shall only light up when pump is engaged.

CLASS A FOAM TANK GAUGE
One (1) Fire Research brand, Model WLA360-A00 tank level gauge shall be provided on the pump operator’s panel to monitor the foam concentrate storage tank level. The gauge shall indicate the foam concentrate storage tank liquid level on an LED bar graph display.

CAB MOUNTED -- CLASS A FOAM TANK GAUGE
A Fire Research TankVision miniature foam tank gauge matching the main gauge shall be installed in the cab console. The gauge shall only light up when pump is engaged.

TEST DATA AND SAFETY PLACARDS
The pump panel shall be provided with labels required by applicable sections of NFPA #1901. The labels shall be installed at the operator's area that provides rated capacities, pressure ratings, and engine speeds as determined by the certification tests. The no-load governed speed of the engine, as stated by the engine manufacturer, shall also be included. The labels shall be provided with all information at the factory and be attached to the apparatus prior to delivery.

15.A

Boise Mobile Equipment
08/30/22
17 PUMP PANEL LIGHT SHIELD
There shall be one (1) stainless steel powder coated matte black light shield assembly provided and installed above the pump panel area. There shall be three (3) TecNiq LED lights installed within the shield. The center light shall illuminate upon main pump engagement.

There shall be a switch at the pump operators panel to activate the lights.

PUMP ENCLOSURE WORK LIGHTS
Two (2) TecNiq LED work lights shall be installed in the pump enclosure. The work lights shall have clear lenses and shall have a control switch which shall be located on the pump panel.

DESIGN AND SCOPE OF MINI PUMPER BODY
The body shall be designed and constructed of commonly available structural components for ease of repair and maintenance. The body shall be of a modular design with the body structure independent of the chassis frame rails. The body module shall be mounted to the chassis frame rails utilizing a unique double spring mounting system for flexibility and durability over the lifetime of the apparatus. The fabrication of the body shall be of welded construction to withstand the rigors of fire service use.

The body shall be designed to incorporate and support the tank, compartments, and all other equipment intended to be stored in or mounted to the body module. The body skeleton and compartment framework shall be designed of tubular members for increased strength and stress resistance. There shall be no sheet metal or extrusions utilized in the foundation or structural components of the body module due to their critical role in assuring lifetime durability, functionality and usability.

Top of body surface shall be even with the top of the cab.

BODY FRAMEWORK
The entire body framework shall be fabricated of 6061-T6 aluminum architectural style tubing. The body framework shall be a completely welded unit, forming a connected, stable frame for strength, longevity and providing the skeleton of the body module. The internal upright members of the framework shall act as support for the top layer of the body module. The external upright members shall act as an exoskeleton providing form and support for compartments while acting as the external surfaces of the module. The framework shall define the compartment openings and provide a rigid mounting location for all compartments and doors.

The foundation cross-members shall be placed perpendicular to the chassis frame rails in the wheel well area extending the full width of the body and shall be constructed of 3 inch high x 2 inch wide x .250 inch tubing.

The foundation members parallel to the chassis frame rails shall be constructed of 3 inch square x .250 inch tubing and shall connect the foundation cross members and extend the full length of the body.

15.A

Boise Mobile Equipment
08/30/22
18 All tank support cross members shall be placed to support the water tank as per the tank manufacture’s recommendation. These supports shall be constructed of 3 inch high x 2 inch wide x .250 inch aluminum tubing.

The tank support angles shall be constructed of 4 inch x 4 inch x .250 inch thick angles and shall be placed at the tank sides parallel to the chassis frame rails to provide lateral support for the tank and protection from debris from the wheels.

The internal upright supports for any ceiling and top component shall be placed to provide support for all components and shall be constructed of aluminum tubing measuring 2 inch square x .250 inch wall thickness.

All front to rear connecting members shall be 3 inches high x 2 inches wide x .125 inch wall thickness and shall be placed in between the interior upright support members to provide rigidity, stability and support to all top layer components. All gussets shall be constructed of 2 inches high x 3 inches wide x .250 inch thick plate which shall be placed on the top and bottom of the foundation cross members where they intersect with the exterior members.

BODY MOUNTING SYSTEM
The mounting assembly shall be designed to isolate and protect the body module from vibration and twisting stresses imparted by the flexing of the chassis frame rails. The body module shall employ spring loaded body mounting assemblies. Each two piece mounting assembly shall be designed to positively position the body on the frame rails while preventing lateral and forward or aft movement. Mounting assemblies shall be placed forward and rearward of the rear axle as necessary to provide a strong and stable mounting of the body module.

Each mounting assembly shall consist of a “male” upper mounting bracket and a “female” lower mounting bracket. The upper mounting brackets shall be fabricated from .250 inch thickness steel plate, with .250 inch painted steel lower mounting brackets. The upper mounting brackets shall be welded directly to the foundation connecting members. The lower mounting brackets shall be bolted to the exterior side facing surface of the chassis frame rails.

The mounting brackets shall be aligned and connected by two (2) 5/8 inch diameter grade 8 bolts equipped with compression springs. The springs shall be of the appropriate tension rating for the weight requirements of the body module. The mounting assembly shall be designed to completely eliminate sheering forces on the mounting bolts.

The foundation connecting members shall be placed on top of the chassis frame rails for added strength and stability. The foundation members shall be isolated from the steel chassis frame rails by .25 inch thickness steel plates which have .5 inch thick 80 durometer rubber pads vulcanized to the bottom surface of each plate. The steel plates shall be welded to the bottom of the foundation, doubling as additional gussets at foundation cross member joints.

BODY MATERIAL

15.A

Boise Mobile Equipment
08/30/22
19 All materials utilized shall be of the correct type, alloy, and thickness to withstand the intended usage and provide protection against cracking, corrosion or metal fatigue. The body compartments shall be fabricated using .125 inch 5052-H32 aluminum for most compartments unless otherwise stated. Any use of proprietary parts or materials in the construction of the body shall be unacceptable, due to potential delays or difficulties in an event of future repairs or when service becomes necessary.

All external upright supports for integral compartments shall incorporate a second set of upright supports constructed of 3 inch wide x 2 inch deep x .250 inch wall thickness and shall be located outboard of the internal upright supports to provide a rigid structure for the compartments to be mounted to. The compartment openings shall be constructed of 3 inch high x 2 inch wide x .125 inch wall thickness cross members and shall be placed in between the external upright supports to define the openings of all enclosed body compartments again, providing a rigid mounting location for compartments.

COMPARTMENT FLOOR-SWEEP OUT STYLE
Each compartment shall feature a raised floor sufficient enough so the lip of the compartment shall clear the frame rail of the body module to allow debris to be removed easily from the compartment. A hat shaped support shall be placed under the floor to improve stability and prevent bowing of the floor with use and age.

COMPARTMENTATION
All compartments shall be constructed of smooth aluminum and welded for strength and shall be sealed from the elements. The compartments shall be attached to the aluminum superstructure only, in order to maintain a truly modular design. Each compartment shall include ventilation louvers which shall be provided on each side panel of the compartment to maximize moisture evacuation for the protection of the equipment and the compartment itself. Louvers shall be placed in the ventilation holes to prevent debris transfer to and from the inside of the body module. Each compartment shall feature a smooth edges and surfaces from the walls to each weld without sharp edges in the material.

WILDLAND VEHICLE - 60" CA - SLIP IN, TYPE 6

COMPARTMENT DFF
One full height compartment shall be provided on the driver's side of the apparatus body, forward of the rear wheels. This compartment shall span from the front of the body to the front of the rear wheel well quarter panel in width and from below the horizontal compartment walkway to the rub rail in height.

Approximate compartment dimensions: 29" wide x 53" high x 22" deep. The compartment shall include four (4) adjustable tracks which shall be installed, with two (2) tracks on each side wall.

There shall be PAC-TRAC installed on all three (3) walls.

15.A

Boise Mobile Equipment
08/30/22
20 This compartment shall have an isolated group 27 battery to provide power for equipment. The air compressor for the air horn shall also be mounted next to the group 27 battery. There shall be a floor installed above listed items to provid a floor for the compartment.

COMPARTMENT VENTILATION LOUVERS
The specified compartments shall be provided with ventilation louvers. These units shall be approximately 4" to 6" in size to allow exterior air or interior air movement.

COMPARTMENT FLOOR DRAIN
The compartment shall be provided with rear corner floor drains to the underside of the body.

COMPARTMENT SILL PLATE
The compartment shall feature a polished stainless steel sill plate protecting the painted surface of the compartment when items are accessed.

ADJUSTABLE TRACKING -- COMPARTMENT EQUIPMENT MOUNTING
Adjustable Uni-Strut equipment mounting tracks shall be installed inside the compartment with two (2) channels on the left wall and two (2) channels on the right wall. The tracks shall be positioned to provide support for equipment mounting. The length of the tracks shall be sized to allow for optimum use of the compartment interior.

COMPARTMENT GRATING
The compartments shall be fitted with removable interlocking vinyl Dri-Dek grating. This material shall be resistant to heat, cold, ultra-violet radiation, mechanical impacts, chemical actions and is corrosion resistant.

COMPARTMENT DCU
One horizontal compartment shall be provided above the rear wheel well on the driver's side of the apparatus body. This compartment shall span between the rescue style compartment forward of the rear wheel well to the rear of the body in width and from below the horizontal compartment walkway to the top of the rear wheel well quarter panel in height. Approximate compartment dimension: 73"wide x 24" high x 22" deep.

The compartment shall include four (4) adjustable tracks which shall be installed, with two (2) tracks on each side wall.

The compartment shall get PAC-TRAC on all three (3) walls and the compartment floor.

15.A

Boise Mobile Equipment
08/30/22
21 COMPARTMENT VENTILATION LOUVERS
The specified compartments shall be provided with ventilation louvers. These units shall be approximately 4" to 6" in size to allow exterior air or interior air movement.

COMPARTMENT FLOOR DRAIN
The compartment shall be provided with rear corner floor drains to the underside of the body.

COMPARTMENT SILL PLATE
The compartment shall feature a polished stainless steel sill plate protecting the painted surface of the compartment when items are accessed.

COMPARTMENT DRF
One compartment shall be provided on the driver's side of the apparatus body aft of the rear wheels. This compartment shall span from behind the rear wheel well quarter panel to the rear of the body in width and from below the horizontal compartment above the rear wheel well quarter panel to the rub rail in height. Approximate compartment dimensions: 22" wide x 15" high x 22" deep. The compartment shall include four (4) adjustable tracks which shall be installed, with two (2) tracks on each side wall.

COMPARTMENT VENTILATION LOUVERS
The specified compartments shall be provided with ventilation louvers. These units shall be approximately 4" to 6" in size to allow exterior air or interior air movement.

COMPARTMENT FLOOR DRAIN
The compartment shall be provided with rear corner floor drains to the underside of the body.

COMPARTMENT SILL PLATE
The compartment shall feature a polished stainless steel sill plate protecting the painted surface of the compartment when items are accessed.

ADJUSTABLE TRACKING -- COMPARTMENT EQUIPMENT MOUNTING
Adjustable Uni-Strut equipment mounting tracks shall be installed inside the compartment with two (2) channels on the left wall and two (2) channels on the right wall. The tracks shall be positioned to provide

15.A

Boise Mobile Equipment
08/30/22
22 support for equipment mounting. The length of the tracks shall be sized to allow for optimum use of the compartment interior.

ADJUSTABLE SHELF
There shall be one (1) adjustable shelf installed; and the shelf shall be constructed of .125" thick smooth aluminum plate and be mounted in the specified compartment with double bolt aluminum shelf brackets. The shelf shall have a broken front edge, and a broken rear edge for added strength and reinforcement.

COMPARTMENT SHELF GRATING
The specified compartment shelf shall be fitted with removable interlocking vinyl Dri-Dek grating. This material shall be resistant to heat, cold, ultra-violet radiation, mechanical impacts, chemical actions and is corrosion resistant.

The compartment shelf and or shelves shall have a red and white 3M Diamond Grade reflective stripe applied horizontally on the front edge. The stripe shall be a 1-1/2" minimum in width. 500# ROLL OUT TRAY
There shall be one (1) 500# capacity roll out tray(s) provided and installed in the specified compartments. The tray(s) shall be constructed of .188” smooth aluminum with a 2” lip on all four sides. The tray(s) shall roll fully out of the compartment, and shall be equipped with a locking device to hold the tray in both the in and out positions.

COMPARTMENT SLIDE OUT TRAY GRATING
The specified compartment slide out tray shall be fitted with removable interlocking vinyl Dri-Dek grating. This material shall be resistant to heat, cold, ultra-violet radiation, mechanical impacts, chemical actions and is corrosion resistant.

The roll out slide tray and or trays shall have a red and white 3M Diamond Grade reflective stripe applied horizontally on the front and side edges of the tray. The stripe shall be a 1-1/2" minimum in width.

COMPARTMENT PFF
One full height compartment shall be provided on the passenger's side of the apparatus body forward of the rear wheels. This compartment shall span from the front of the body to the front of the rear wheel well quarter panel in width and from below the horizontal compartment walkway to the rub rail in height. Approximate compartment dimensions: 29" wide x 53" high x 22" deep.

15.A

Boise Mobile Equipment
08/30/22
23 The compartment shall include four (4) adjustable tracks shall be installed, with two (2) tracks on each side wall.

The compartment shall get PAC-TRAC on all three (3) walls.

COMPARTMENT VENTILATION LOUVERS
The specified compartments shall be provided with ventilation louvers. These units shall be approximately 4" to 6" in size to allow exterior air or interior air movement.

COMPARTMENT FLOOR DRAIN
The compartment shall be provided with rear corner floor drains to the underside of the body.

COMPARTMENT SILL PLATE
The compartment shall feature a polished stainless steel sill plate protecting the painted surface of the compartment when items are accessed.

ADJUSTABLE TRACKING -- COMPARTMENT EQUIPMENT MOUNTING
Adjustable Uni-Strut equipment mounting tracks shall be installed inside the compartment with two (2) channels on the left wall and two (2) channels on the right wall. The tracks shall be positioned to provide support for equipment mounting. The length of the tracks shall be sized to allow for optimum use of the compartment interior.

COMPARTMENT GRATING
The compartments shall be fitted with removable interlocking vinyl Dri-Dek grating. This material shall be resistant to heat, cold, ultra-violet radiation, mechanical impacts, chemical actions and is corrosion resistant.

COMPARTMENT PCU
One horizontal compartment shall be provided above the rear wheel well quarter panel on the passenger's side of the apparatus body. This compartment shall span between the rescue style compartment forward of the rear wheel well to the rear compartment in width and from below the horizontal compartment walkway to the top of the rear wheel well quarter panel in height. Approximate compartment dimension: 48"wide x 24" high x 22" deep. The compartment shall include four (4) adjustable tracks which shall be installed, with two (2) tracks on each side wall.

COMPARTMENT VENTILATION LOUVERS

15.A

Boise Mobile Equipment
08/30/22
24 The specified compartments shall be provided with ventilation louvers. These units shall be approximately 4" to 6" in size to allow exterior air or interior air movement.

COMPARTMENT FLOOR DRAIN
The compartment shall be provided with rear corner floor drains to the underside of the body.

COMPARTMENT SILL PLATE
The compartment shall feature a polished stainless steel sill plate protecting the painted surface of the compartment when items are accessed.

ADJUSTABLE TRACKING -- COMPARTMENT EQUIPMENT MOUNTING
Adjustable Uni-Strut equipment mounting tracks shall be installed inside the compartment with two (2) channels on the left wall and two (2) channels on the right wall. The tracks shall be positioned to provide support for equipment mounting. The length of the tracks shall be sized to allow for optimum use of the compartment interior.

ADJUSTABLE SHELF
There shall be one (1) adjustable shelf installed; and the shelf shall be constructed of .125" thick smooth aluminum plate and be mounted in the specified compartment with double bolt aluminum shelf brackets. The shelf shall have a broken front edge, and a broken rear edge for added strength and reinforcement.

COMPARTMENT SHELF GRATING
The specified compartment shelf shall be fitted with removable interlocking vinyl Dri-Dek grating. This material shall be resistant to heat, cold, ultra-violet radiation, mechanical impacts, chemical actions and is corrosion resistant.

The compartment shelf and or shelves shall have a red and white 3M Diamond Grade reflective stripe applied horizontally on the front edge. The stripe shall be a 2" minimum in width.

COMPARTMENT GRATING
The compartments shall be fitted with removable interlocking vinyl Dri-Dek grating. This material shall be resistant to heat, cold, ultra-violet radiation, mechanical impacts, chemical actions and is corrosion resistant.

COMPARTMENT PRL

15.A

Boise Mobile Equipment
08/30/22
25 One compartment shall be provided on the passenger's side of the apparatus body aft of the rear wheels. This compartment shall span from behind the rear wheel well quarter panel to the rear of the body in width and from below the horizontal compartment above the rear wheel well quarter panel to the rub rail in height. Approximate compartment dimensions: 22" wide x 46" high x 22" deep. The compartment shall include four (4) adjustable tracks which shall be installed, with two (2) tracks on each side wall.

COMPARTMENT FLOOR DRAIN
The compartment shall be provided with rear corner floor drains to the underside of the body.

COMPARTMENT SILL PLATE
The compartment shall feature a polished stainless steel sill plate protecting the painted surface of the compartment when items are accessed.

ADJUSTABLE TRACKING -- COMPARTMENT EQUIPMENT MOUNTING
Adjustable Uni-Strut equipment mounting tracks shall be installed inside the compartment with two (2) channels on the left wall and two (2) channels on the right wall. The tracks shall be positioned to provide support for equipment mounting. The length of the tracks shall be sized to allow for optimum use of the compartment interior.

ADJUSTABLE SHELVES
There shall be two (2) adjustable shelves installed; and the shelves shall be constructed of .125" thick smooth aluminum plate and be mounted in the specified compartment with double bolt aluminum shelf brackets. Each shelf shall have a broken front edge, and a broken rear edge for added strength and reinforcement.

The compartment shelf and or shelves shall have a red and white 3M Diamond Grade reflective stripe applied horizontally on the front edge. The stripe shall be a 2" minimum in width.

WATER TANK CARGO DOOR
Provide a single piece aluminum tread plate cover over the water tank. The cover shall be forward hinged. The door shall open to the front of the vehicle. The door shall utilize gas struts to hold open. The tank cover shall be provided with one (1) TecNiq E-10 light. The light shall activate when the door is opened the door shall be wired to the door ajar. The door shall be black duracoated aluminum treadplate and support a minimum of 250lbs each when closed.

REAR COMPARTMENT

15.A

Boise Mobile Equipment
08/30/22
26 The apparatus shall have a 5" high rear compartment (BCF) which shall be located along the frame rails and centered. The compartment shall measure approximately 30" wide x 5" high x 72" deep. An aluminum treadplate drop down slab door with two flush thumb latches shall be provided.

COMPARTMENT FLOOR DRAIN
The compartment shall be provided with rear corner floor drains to the underside of the body.

COMPARTMENT SILL PLATE
The compartment shall feature a polished stainless steel sill plate protecting the painted surface of the compartment when items are accessed.

LEFT SIDE -- HOSE BED COMPARTMENTS
There shall be a back board compartment above the drivers side compartments. On top of the BB compartment, there shall be a hose bed with a 1.5" pre-connect. There shall be an embossed diamond plate door on top of the hose bed.

WHEEL WELL LINERS
Wheel well liners designed to protect the body from impact resulting from road debris thrown by the tires shall be installed. The removable liners shall be constructed from UHMW material to encompass the entire inner wheel well area. The liners shall be secured with threaded fasteners.

REAR WHEEL FENDERETTES
Polished stainless steel fenderettes shall be installed at each rear wheel opening. The fenderettes shall be positioned outside of the wheel well panel to cover the tire area that extends past the body. The fenderettes shall be secured with threaded fasteners.

FUEL FILL ACCESS
An access opening designed to accommodate the OEM fuel fill assembly and angled insert shall be provided in the driver's side wheel well area.

RIGHT SIDE BODY -- SCBA CYLINDER STORAGE PROVISIONS
A storage area for an SCBA cylinder shall be provided in the forward area of the passenger’s side wheel well.

Dimensions shall be 8" diameter x 26” deep. A BME brushed stainless steel door and frame assembly shall be installed.

15.A

Boise Mobile Equipment
08/30/22
27 The SCBA cylinder storage tube shall be made from plastic.

SCBA CYLINDER STRAPS
There shall be a 1" nylon tether installed to secure the bottle in the storage tube.

RIGHT SIDE BODY -- SCBA CYLINDER STORAGE PROVISIONS
A storage area for an SCBA cylinder shall be provided in the rearward area of the officer's side wheel well.

Dimensions shall be 8" diameter x 26" deep. A BME brushed stainless steel door and frame assembly shall be installed.

The SCBA cylinder storage tube shall be made from plastic.

SCBA CYLINDER STRAPS
There shall be a 1" nylon tether installed to secure the bottle in the storage tube.

WHEEL CHOCK STORAGE -- LEFT SIDE
A storage compartment of composite construction shall be provided for a wheel chock in the forward area of the left side wheel well. The compartment door shall be brushed stainless steel with SouthCo latch assembly.

RUB RAILS
The sides of the lower body area fore and aft of the wheel well area shall be provided with 3" x 1.5" x .250" extruded aluminum rub rails, with end caps or angle corners. The rub rails shall be equipped with red and white DOT type reflective striping.

FRONT OF BODY -- PROTECTIVE SURFACE
The entire front of the apparatus body shall include a protective surface, constructed of aluminum tread plate material. This panel shall be covered with a black protective coating.

FRONT CORNERS OF BODY -- PROTECTIVE SURFACES
The front corners of the apparatus body shall include a protective surface installed. The surface shall be constructed of mirror finish stainless steel material.

REAR BODY PANELS

15.A

Boise Mobile Equipment
08/30/22
28 The rear panels of the apparatus body shall be made from smooth aluminum for easy application of the chevron graphics.

OUTER REAR BODY PANELS -- PROTECTIVE COVERING
The rear outer panels of the body shall have protective surfaces installed on the corners. The protective covering shall be constructed of mirror finish stainless steel material.

TOP OF BODY COMPARTMENTS -- PROTECTIVE SURFACES
The top of the side compartments shall have a protective surfaces installed. The surface shall be constructed of embossed aluminum tread plate material.

ANODIZED ALUMINUM DRIP RAIL
All enclosed compartment doors shall be provided with an anodized aluminum drip rail above the doors.

COMPARTMENT DOORS
All compartment doors to have locking D handle latches with 1250 key.

ALUMININUM – COMPARTMENT DOOR, HINGED OVERLAP
Four (4) single, vertically hinged doors shall be provided and shall be fabricated of aluminum. The frame of the door shall be constructed of 1.75” x 1.75” x .125” aluminum tubing to prevent corrosion and provide structural support. The spacing created by the frame tubing shall be filled with Styrofoam for added insulation and noise reduction. The exterior surface shall be .125” aluminum for durability. The interior surface shall be .080” aluminum. There shall be no mechanical fasteners, such as bolt heads or rivets on the inside or outside of the doors.

The exterior of the door shall overlap the opening of the compartment. A .75” lip shall be constructed around the opening of the compartment and the exterior of the door. A rubber seal shall be installed on the .75” lip on both the compartment and the door to provide for a double seal against water and dust. A rain gutter shall be mounted above the door creating a third layer of water protection.

The door shall be designed utilizing a D-ring style latch system. A 6” stainless steel D-ring latch, large enough to accommodate a gloved hand, shall be mounted on the exterior of the door. A stainless steel bezel shall be installed to house and protect the D-ring latch mechanism. The easily serviced bezel shall be mounted utilizing stainless steel screws. The D-ring latch mechanism shall be a double catch design. The first catch shall engage to secure the door in the event of improper closure. The second catch shall seal the door from water and other elements once the door has been properly closed.

15.A

Boise Mobile Equipment
08/30/22
29 The door shall be mounted using a stainless steel piano style hinge and a .250” diameter hinge pin for stability.

The vertical hinge shall be mounted to the body frame with threaded inserts and stainless steel screws.

A gas strut shall be utilized to hold the door in the open position and to prevent the door from slamming during closing. The gas strut shall be mounted directly to the door with a stainless steel bracket assembly for stability and ease of maintenance. The gas strut shall be mounted to the interior of the compartment with a fully adjustable assembly.

The exterior of the compartment doors and the door frames shall be painted to match the body in quality and tone. The interior surface shall not be painted, it shall be sanded utilizing a dual orbital technique.

ALUMININUM – COMPARTMENT DOOR, LIFT UP HINGED OVERLAP
Two (2) single, horizontally hinged doors shall be provided and shall be fabricated of aluminum. Each door shall feature exterior surfaces which overlap the opening of the compartment. The exterior surface shall be .125” aluminum. The interior surface shall be .080” aluminum. The frame of the door shall be constructed of aluminum tubing to provide structural support. The spacing created by the frame tubing shall be filled with Styrofoam for insulation, and noise reduction.

A .75” lip shall be constructed around the opening of the compartment and the exterior of the door. A rubber seal shall be installed on the .75” lip of both the compartment and the door to provide for a double seal against water and dust. A rain gutter shall be mounted above the latch type door for an added third layer of water protection.

The door shall be designed utilizing a D-ring latch system. A 6” large D-ring latch will be provided to accommodate a gloved hand. A stainless steel bezel shall be installed to house and protect the D-ring latch mechanism. The easily serviced bezel shall be mounted utilizing stainless steel screws for added stability of the mechanism and ease of maintenance in the event of damage. The door shall be mounted with a stainless steel hinge with .25” diameter hinge pin for stability. The horizontal hinge shall be mounted to the body frame with threaded inserts, and stainless steel screws to preserve functionality with use or age and ease of maintenance in the event of damage.

Gas struts shall be utilized to hold the door in the open position and to prevent the door from slamming during closing. The gas struts are mounted directly to the door with a stainless steel bracket assembly for stability and ease of maintenance. The gas struts shall be mounted to the interior of the compartment with fully adjustable assembly for ease of adjustment and maintenance while increasing stability.

The exterior of the compartment doors and the door jams shall be painted to match the body in quality and tone.

The interior of the door shall not be painted due to lack of exposure and inherent resistance to corrosion. The interior of the door shall be sanded utilizing a dual orbital technique.

TOP SIDE BODY COMPARTMENT DOOR DS

15.A

Boise Mobile Equipment
08/30/22
30 The top side body compartment on the drivers side shall be provided with full length embossed aluminum textured tread plate doors hinged along the outboard edge and held open by gas struts.

Provide each door with two (2) chrome plated grab handle and thumb latches to secure when closed.

REAR STEP BUMPER
The rear step bumper shall be constructed of steel channel providing a minimum of 12" stepping surface shall be mounted to the chassis frame rails with two (2) combination rear body and bumper supports. The rear tow eyes shall be above the rear step bumper.

The rear step shall be painted with the top surfaces of the rear step which shall feature black Dura-coat. The step shall be mounted 2” higher than that of the body. Smooth eye tie-off ponits shall be provided on each side of the bumper frame structure rated for 9000#.

REAR VERTICAL RAILINGS
Two (2) knurled type non-slip handrails, approximately 24” in length, shall be vertically installed, one each side rear of body.

WATER TANK SPECIFICATIONS
The water tank shall have a capacity of 250 gallons with an intergrated 10 gallon foam tank.

The water tank shall be designed with four (4) walls coming up to the height of the body to provide a storage area.

There shal be a polished aluminum diamond plate protective panel that shall extend from the floor up to the tank cover, across the rear of the tank and attached to the body cargo inside panels with aluminum angle and stainless hardware. Provide the panel with a minimum 1" break for added strength.

DIRECT TANK FILL 3/4"
One (1) 3/4" GHT direct tank fill valve shall be installed in a location that will be able to fill the tank from normal house pressure.

Tank Fill Valve -- Left Rear
A valve for direct filling of the tank shall be supplied. The 1/4 turn valve shall be configured with 2-1/2" NH female threads, debris screen, threaded plug with retention chain and lever handle. The valve shall be located on the rear of the pump panel.

15.A

Boise Mobile Equipment
08/30/22
31 One (1) Akron 8825 series swing-out style valve(s) shall be supplied and installed. All valves shall be designed to operate under normal conditions up to 500 PSI and shall have dual seats to work in both pressure and vacuum environments. All valves and controls shall be easily accessible for service, repair or replacement.

The specified valve shall have a direct actuated ‘local’ control Akron Model TSC valve handle.

One (1) chrome brass 2-1/2" NH rocker lug plug with a securing chain or cable shall be installed on the intake.

PAC-TRAC ADJUSTABLE TRACKING -- COMPARTMENT MOUNTING
The compartments {will/shall} be equipped with triple track Performance Advantage vertically mounted equipment mounting PAC-TRAC tracks. The aluminum adjustable mounting tracks {will/shall} be installed inside the compartments with two (2) channels on the left wall and two (2) channels on the right wall.

12 VOLT ELECTRICAL SPECIFICATIONS
The following describes the low voltage electrical system on the apparatus including all panels, electrical components, switches and relays, wiring harnesses and other electrical components. The apparatus manufacturer shall conform to the latest Federal DOT standards, current automotive electrical system standards and the applicable requirements of NFPA.

Wiring shall be stranded copper or copper alloy conductors of a gauge rated to carry 125 percent of the maximum current for which the circuit is protected. Voltage drops shall not exceed 10 percent in all wiring from the power source to the using device. The wiring and wiring harness and insulation shall be in conformance with SAE and NFPA standards. The wiring harness shall conform to SAE J-1128 with GXL temperature properties.

Exposed wiring shall be run in a loom with a 290 degree Fahrenheit rating. Wiring looms shall be properly supported and attached to body members. Electrical conductors shall be constructed in accordance with applicable SAE standards, except when good engineering practice requires special construction.

All wiring connections and terminations shall provide positive mechanical and electrical connections and be installed in accordance with the device manufacturer's instructions. When wiring passes through metal panels, electrical connections shall be with mechanical type fasteners and rubber/plastic grommets Wiring between the cab and body shall be split using Deutsche type connectors or enclosed in a terminal junction panel allowing body removal with minimal impact on the apparatus electrical system. Connections shall be insulated with heat shrink tubing to resist moisture and foreign debris such as grease and road grime.

Weather resistant connectors shall be provided throughout the system.

Electrical junction or terminal boxes shall be weather resistant and located away from water spray conditions.

When required, automatic reset breakers and relays shall be housed in the main body junction panel.

15.A

Boise Mobile Equipment
08/30/22
32 There shall be no exposed electrical cabling, harnesses, or terminal connections located in compartments, unless enclosed in an electrical junction box or covered with a removable electrical panel. Wiring shall be secured in place and protected against heat, liquid contaminants and damage and shall be uniquely identified at least every six inches (6") by color coding or permanent marking with a circuit function code and identified on a reference chart or electrical wiring schematic per requirements of applicable NFPA standards.

Low voltage protective devices shall be provided for the electrical circuits. The devices shall be accessible and located in required terminal connection locations or weather resistant enclosures. Over current protection devices shall be automatic reset type suitable for electrical equipment and shall meet SAE standards. All electrical equipment, switches, relays, terminals, and connectors shall have a direct current rating of 125 percent of maximum current for which the circuit is protected. Electro-magnetic interference suppression shall be provided in the system as required in applicable SAE standards.

The electrical system shall include the following:

Electrical terminals in weather exposed areas shall have a non-conductive grease or spray applied. All terminal plugs located outside of the cab or body shall be treated with a corrosion preventative compound.

All electrical wiring shall be placed in a protective loom or be harnessed.

Exposed connections shall be protected by heat shrink and or a sealed connector.

Large fender washers shall be used when fastening equipment to the underside of the cab roof and all holes made in the roof shall utilize a weatherproof strain relief.

Electrical components installed in exposed areas shall be mounted in a manner that will not allow moisture to accumulate inside.

A service loop shall be provided behind all electrical appliances to allow them to be pulled away from their mounting area for inspection and service work.

Warning lights shall be switched in the chassis cab with labeled rocker type switches located in an accessible location. Individual rocker switches shall be provided only for warning lights provided exceeding the minimum level of warning lights in either the stationary or moving modes. All electrical equipment switches shall be appropriately identified as to their function. For easy nighttime operation, an integral indicator light shall be provided to indicate when a circuit is energized.

A single warning light switch shall activate all required warning lights. This switch will allow the vehicle to respond to an emergency "calling for the right of way". When the parking brake is activated, a "blocking the right of way" system shall be automatically activated per NFPA requirements. All "clear warning lights" shall be automatically shed on actuation of parking brake.

15.A

Boise Mobile Equipment
08/30/22
33 Upon completion of the vehicle and prior to delivery, the apparatus shall be electrically tested and the electrical testing, certifications, and test results shall be submitted with delivery documentation per the requirements of NFPA.

ELECTRICAL WIRING HARNESS
The electrical system shall be divided into separate harnesses. The individual harnesses shall be connected with Deutsch type quick connectors. The electrical power to all apparatus lighting and accessories shall be supplied by an ignition activated solenoid.

CAB CONSOLE
The cab shall be equipped with an operator's control console located between the driver's and officer's seats.

This console shall be designed to be of sufficient size to allow for the installation of the switches and controls listed below. The console shall be designed to have removable panels to allow for access to the internally mounted electrical components and wiring. This console shall be powder coated with a non-glare black finish.

Cencom Carbide siren controller
Department supplied radio faceplate
The rear section of the console will have a removable top & side door for access to all 12v electric equipment, wiring & controls for the entire fire body & equipment. A total of three (3) USB ports and one (1) 12 volt port will be installed. (Placement to be confirmed by department).

Two cup holders will integrated also. There will be wiring for two (2) mobile radios in the cab console. There will also be space to mount 2 portable radios on top two (2) 2.5” x console width map box on the rear of the console.
12 VOLT ACCESSORY CIRCUIT-CAB CONSOLE
One (1) dedicated circuit; 12 volt, 40 Amp, power and ground on 3/8 stud and fused at battery shall be provided in the cab console. The circuit shall be for future installation of radios or accessories.

CUP HOLDER
The console shall have two (2) cup holders installed. Exact location to be determined at the preconstruction meeting.

CONSOLE ARM REST

15.A

Boise Mobile Equipment
08/30/22
34 Two (2) Troy arm rest model: AC-SIDEARM-9 shall be provided and installed on each side of the console.

BATTERY SWITCH - MASTER DISCONNECT
A battery disconnect switch controlling the 12 volt power supply from the battery system shall be located on the dash, to the left of the steering wheel.

The rocker switch shall be labled and light up when battery power is on.

BATTERY CHARGER
Provide one (1) Pro Mariner 1240P 40 amp battery charger. 120 VOLT SHORE POWER RECEPTACLE
A Kussmaul "Super Auto-Eject with deluxe cover" shore power receptacle shall be provided with an enclosure for protection from road dirt and damage. The shore power plug shall be "ejected" when the chassis's engine starter is engaged and the receptacle shall be wired to any 120 volt equipment requiring shore power.

Provide Auto Eject with a hinged black weatherproof cover with integral display There will be a label installed near the inlet(s) that state the following:
· Line Voltage
· Current Ratting (amps)
· Phase
· Frequency
Engine block heater will not be connected.

Location: Driver side front chassis fender.

IDENTIFICATION LIGHTS
Nine (9) LED identification lights shall be installed on the vehicle as required by applicable highway regulations. Product as follows
· Three (3) TecNiq S37-RC09-1 grommet mount rear center of body, RED/CLEAR lense · Four (4) TecNiq S15-RC0P-1 grommet mount rear lower side and upper rear of body, RED/CLEAR lense
· Two (2) TecNiq S15-AC0P-1 grommet mount front lower side of body, AMBER/CLEAR lense

15.A

Boise Mobile Equipment
08/30/22
35 LICENSE PLATE BRACKET AND LIGHT
One (1) Weldon brand, Model #9186-23882-30 clear light fixture, with a cast aluminum license plate mounting bracket, shall be provided at the rear of the body above the driver side DOT lights.

STOP AND TAIL LIGHTS
Two (2) Whelen Model #M6BTT, 4" x 6" LED stop and tail lights with red lenses shall be provided. The light shall be furnished with a optic polycarbonate lens for maximum light spread and furnished with a 6" wire pigtail.

TURN SIGNALS
Two (2) Whelen M-Series 4" x 6" LED directional lights shall be provided. The turn signal lights shall incorporate amber LED's for a maximum population configuration with an amber non-optic polycarbonate lens.

The light head shall have six (6) flash patterns. The encapsulated housing shall be moisture and vibration resistant and furnished with a 6" wire pigtail.

BACK-UP LIGHTS
Two (2) Whelen M-Series, 4" x 6" rear LED back-up lights shall be installed.

TAILLIGHT BEZELS
Two (2) Whelen M Series housings shall be installed at the rear of the apparatus for four (4) Whelen M-Series stop-tail-turn-backup and warning lights.

Each assembly shall consist of the following, top to bottom. * One (1) M6BUW clear back-up light
* One (1) M6T amber turn indicator with arrow
* One (1) M6BTT red stop/tail light
* One (1) M6RR red warning light with red lense.

MAP LIGHT
One (1) flexible LED map light shall be provided on the cab center console. The switch for the map light shall shall go from RED to OFF to WHITE.

CAB GROUND LIGHTS
Four (4) Tecniq E10, LED ground lights shall be installed under the cab step area in compliance with NFPA standards; and activate with the parking brake.

15.A

Boise Mobile Equipment
08/30/22
36 GROUND LIGHTS - FRONT BODY
Two (2) Tecniq E10, LED ground lights shall be installed under the front body compartments, one on each side of the body, the lights shall be wired to the cab door switch, and the switch on the cab console. The lights shall turn on automatically when the cab doors are open and the park brake is engaged.

GROUND LIGHTS - UNDER REAR SIDE COMPARTMENT FLOORS
Two (2) Tecniq E10, LED ground lights shall be installed under the rear side body compartment floors, one on each side of the apparatus, wired to parking brake circuit.

GROUND LIGHTS - UNDER REAR STEP
Two (2) Tecniq E10, LED ground lights shall be installed under the rear step area, one on each side of the apparatus, wired to parking brake circuit.

REAR STEP LIGHTS
Two (2) TecNiq D07 LED step lights with clear lens shall be installed at the rear of the apparatus body to light the rear step, to activate with the ground perimeter lights.

L.E.D. WORK/SCENE LIGHT
A Whelen Pioneer Micro Series, Super-LED flood light model MPR15B shall be provided in the designated location(s).

COMPARTMENT LIGHTING
Two (2) Code 3 800 Series Corner LED lights shall be installed in each of the specified compartment(s).

COMPARTMENT LIGHT SWITCHES
Each interior compartment light shall be automatically controlled by a door activated "On-Off" switch.

DOOR OPEN WARNING LIGHT
A door open warning light with audible alarm shall be installed on cab dash. The light shall be a flashing jumbo LED light with a red lens. The light shall include a label, “Do Not Move Apparatus When Light is ON”.

BACK UP ALARM

15.A

Boise Mobile Equipment
08/30/22
37 One (1) solid state back up alarm shall be provided at the rear of the apparatus. The back up alarm shall be wired to the reverse circuit of the transmission, and shall provide an audible alarm to the rear of the apparatus when reverse gear is selected. The alarm shall have a volume of 87 to 112 db while in operation.

HEADLIGHT FLASHER
One (1) Whelen brand, Model #UHF 2150A solid state headlight flasher shall be installed and wired for daytime operation. The flasher shallbe a multipurpose type with a high beam-activated cut out option. The flasher shall be wired to the “Wig Wag” switch on the cab center console, through the parking brake, so that it is disabled when the parking brake is applied.

ELECTRONIC SIREN
Whelen CenCom Carbide, electronic siren shall be provided. The siren control head shall have a 3-position slide switch and 18 push button control head with amplifier control module with pigtails, traffic advisor module and microphone with CCMICX20
Siren head to control all warning and scene lights.

SIREN SPEAKER
One (1) Whelen Model #SA314A siren speaker shall be provided. The 100 watt siren speaker shall be designed with an aluminum housing; with 123 decibel rating.

AIR HORN
One (1) Vlair 12 volt compressor system for air horn operation shall be installed and mounted in a safe, serviceable and low heat area. Air lines shall be routed, secured and covered in split loom.

Part numbers-45050, 91025, 90111, 90007, and 95901. One (1) Wilkerson air regulator model R03-01-000, and One (1) Grover model 1510 air horn and air solenoid model 1132-12V, shall be installed.

ZONE A FRONT UPPER -- LIGHTBAR
One (1) Whelen Liberty II DUO 54" LED lightbar with clear lenses equipped as follows.

Center - Two (2) forward white takedown, One (1) Traffic Emitter Outer, forward facing each side - One (1) steady red, remainder flashing red Corners, Forward each side - One (1) flashing red/white, white disabled with park brake Corners, Rear each side - One (1) flashing red
Sides - One (1) white alley light each side

15.A

Boise Mobile Equipment
08/30/22
38 ZONE A -- LOWER FRONT WARNING LIGHTS
Two (2) Whelen M2 Series wide angle red warning lights with clear lens shall be installed in the front grill of the cab. The warning lights shall incorporate Linear-Super LED and Smart LED technology. The light shall be mounted in a chrome plastic flange bezels assembly.

The specified Whelen M2 lights shall be equipped with chrome plastic flange type light bezel mountings.

ZONE B AND D -- INTERSECTION LIGHTS
Two (2) Whelen M4 Series Model # M4RC red warning light with clear lens shall be provided.

The specified Whelen M4 lights shall be equipped with chrome plastic flange type light bezel mountings.

ZONE B AND D -- LOWER MID BODY WARNING LIGHTS
Two (2) Whelen M4-Series 3" x 5" warning lights shall be installed. The warning lights shall be located one (1) each side, lower mid body. The warning lights shall incorporate Linear-Super LED and Smart LED technology.

The light heads shall have six (6) red Super-LEDs with a clear non-optic polycarbonate lens for maximum light spread. The light head assemblies shall have internal flasher eleven (11) Scan-Lock flash patterns, including steady burn and synchronize power functions. The lights shall have clear lens and chrome plastic bezels.

Mounted above rear wheels.

The specified Whelen M4 lights shall be equipped with chrome plastic flange type light bezel mountings.

ZONE B AND D -- UPPER SIDE FRONT WARNING LIGHTS
Two (2) Whelen M4-Series 3" x 5" warning lights shall be installed. The warning lights shall be located one (1) each side high on the body, as far forward as possible. The warning lights shall incorporate Linear-Super LED and Smart LED technology. The light head configuration shall be designed with eight (8) red Super-LEDs with a clear optic polycarbonate lens. The light heads shall utilize a hybrid TIR optic reflector and chrome vacuum metalized reflector for maximum illumination. The light head shall include fourteen (14) internal Scan-Lock flash patterns including steady burn and High/Low power functions. The lights shall have clear lens and chrome plastic bezels.

Mounted on upper forward body side.

The specified Whelen M4 lights shall be equipped with chrome plastic flange type light bezel mountings.

ZONE B AND D -- UPPER SIDE REAR WARNING LIGHTS

15.A

Boise Mobile Equipment
08/30/22
39 Two (2) Whelen M4-Series 3" x 5" warning lights {will/shall} be installed. The warning lights {will/shall} be located one (1) each side high on the body, as far rearward as possible. The warning lights {will/shall} incorporate Linear-Super LED and Smart LED technology. The light head configuration {will/shall} be designed with eight (8) red Super-LEDs with a clear optic polycarbonate lens. The light heads {will/shall} utilize a hybrid TIR optic reflector and chrome vacuum metalized reflector for maximum illumination. The light head {will/shall} include fourteen (14) internal Scan-Lock flash patterns including steady burn and High/Low power functions. The lights {will/shall} have clear lens and chrome plastic bezels.

Mounted on upper rear body side.

The specified Whelen M4 lights shall be equipped with chrome plastic flange type light bezel mountings.

ZONE C -- UPPER REAR WARNING LIGHTS
Two (2) Whelen M6-Series 4" x 6" flashing warning lights shall be installed. The warning lights shall be located one (1) each side upper rear of body. The warning light shall incorporate Linear-Super LED technology. The lights shall have clear lenses, and chrome plastic bezels.

The specified Whelen M6 lights shall be equipped with chrome plastic flange type light bezel mountings.

ZONE C -- LOWER REAR WARNING LIGHTS
Two (2) Whelen M-Series 4" x 6" warning lights shall be installed. The warning lights shall be located one (1) each side, rear lower area of body. The warning lights shall incorporate Linear-Super LED and Smart LED technology. The light head configuration shall be designed with eight (8) red Super-LEDs with a clear optic polycarbonate lens. The light heads shall utilize a hybrid TIR optic reflector and chrome vacuum metalized reflector for maximum illumination. The light head shall include fourteen (14) internal Scan-Lock flash patterns including steady burn and High/Low power functions. The lights shall have clear lens.

The specified Whelen M6 lights shall be equipped with chrome plastic flange type light bezel mountings.

TRAFFIC ADVISOR
Whelen Model #TANF85, traffic advisor shall be provided. The 47" traffic advisor shall have six (6), 2" x 5", 3/16", (5mm) amber LED light heads with clear optic polycarbonate lenses for maximum light spread. The light heads shall be fully encapsulated to protect against moisture and vibration. The lights shall be mounted within extruded aluminum housing with a black powder coat finish. The traffic advisor shall include a remote control head, Model #TACTLD1, which shall operate the unit. The control head shall have a LED direction indicator and shall be back lit for greater visibility. There shall be high and low power functions available with use of a three-position rocker switch. The traffic advisor functions shall include: right, left, split, and flash activated

15.A

Boise Mobile Equipment
08/30/22
40 through the use of a rotary knob. Easily accessible dip switches at the rear of the control head shall give the operator the choice of eight (8) flash patterns.

The traffic advisor shall have 20' of 9 conductor cable for wiring purposes and shall be surface mounted to the vehicle. The control head shall have a bail bracket included in the installation kit for mounting. The traffic advisor shall have total dimensions of 2-7/8" high x 2-1/4" wide x 47" long.

Location shall be centered in the upper pump panel.

Traffic advsor shall be disabled with pump ignition "ON"..

LED TELELIGHT HEADS

LED SCENE LIGHT
Two (2) Whelen Pioneer Plus PCH1P1 LED Scene Light with telescoping pole mount shall be provided.

Location of lights shall be: One each side of front of body.

REAR RECEIVER HITCH
One (1) Class 4 type trailer hitch, rated at approximately 12,000 lbs. shall be installed on the rear of the apparatus attached to the frame assembly.

TRAILER HITCH POWER PLUG
Wiring shall be provided at the rear of the apparatus for the towing of an auxiliary trailer. A 12 volt seven (7) pin electrical connector shall be wired to the chassis stop, running, and turn lights.

Body Painting Specifications
The body shall feature a single-color paint configuration which involves a two-step process thereby ensuring a durable, high gloss finish.

Paint process shall feature Sikkens high solid LV products and be performed in the following steps:

· Corrosion Prevention - all aluminum surfaces shall be pre-treated with the Alodine 5700 conversion coating to provide superior corrosion resistance and excellent adhesion of the base coat.

15.A

Boise Mobile Equipment
08/30/22
41 · Sikkens Sealer/Primer LV - acrylic urethane sealer/primer shall be applied to guarantee excellent gloss hold-out, chip resistance and a uniform base color.

· Sikkens High Solid LVBT650 (Base coat) - a lead-free, chromate-free high solid acrylic urethane base coat shall be applied, providing excellent coverage and durability. A minimum of two (2) coats shall be applied.

· Sikkens High Solid LVBT650 (Clear coat) - high solid LV clear coat shall be applied as the final step in order to ensure full gloss and color retention and durability. A minimum of two (2) coats shall be applied.

Any location where the material is penetrated after painting, for the purpose of mounting steps, hand rails, doors, lights, or other specified components shall be treated at the point of penetration with a corrosion inhibiting pre-treatment (ECK Corrosion Control). The pretreatment shall be applied to the aluminum sheet metal or aluminum extrusions in all locations where the aluminum has been penetrated. All hardware used in mounting steps, hand rails, doors, lights, or other specified components shall be individually treated with the corrosion inhibiting pre-treatment.

After the paint process is complete, the gloss rating of the unit shall be tested with a 20degree gloss meter.

Coating thickness shall be measured with a digital MIL gauge and the orange peel with a digital wave scan device.

The body shall be painted using a single color to match the cab primary color, and then shall be buffed to a high gloss finish.

Pump, plumbing and tank cargo space to be finished in Black truck bed liner.

15.A

Boise Mobile Equipment
08/30/22
42 PAINTING SPECIFICATIONS

PAINTING -- EXTERIOR CAB
The commercial cab exterior shall be finish painted over the original OEM paint with a Sikkens system, single color, to match the Purchaser's furnished paint code. RED FLNA 3225

Repainted areas to include door and hood jambs

BODY PAINTING SPECIFICATIONS
The body shall feature a single-color paint configuration which involves a two-step process thereby ensuring a durable, high gloss finish.

Paint process shall feature Sikkens high solid LV products and be performed in the following steps:

· Corrosion Prevention - all aluminum surfaces shall be pre-treated with the Alodine 5700 conversion coating to provide superior corrosion resistance and excellent adhesion of the base coat.

· Sikkens Sealer/Primer LV - acrylic urethane sealer/primer shall be applied to guarantee excellent gloss hold-out, chip resistance and a uniform base color.

· Sikkens High Solid LVBT650 (Base coat) - a lead-free, chromate-free high solid acrylic urethane base coat shall be applied, providing excellent coverage and durability. A minimum of two (2) coats shall be applied.

· Sikkens High Solid LVBT650 (Clear coat) - high solid LV clear coat shall be applied as the final step in order to ensure full gloss and color retention and durability. A minimum of two (2) coats shall be applied.

Any location where the material is penetrated after painting, for the purpose of mounting steps, hand rails, doors, lights, or other specified components shall be treated at the point of penetration with a corrosion inhibiting pre-treatment (ECK Corrosion Control). The pretreatment shall be applied to the aluminum sheet metal or aluminum extrusions in all locations where the aluminum has been penetrated. All hardware used in mounting steps, hand rails, doors, lights, or other specified components shall be individually treated with the corrosion inhibiting pre-treatment.

After the paint process is complete, the gloss rating of the unit shall be tested with a 20degree gloss meter.

Coating thickness shall be measured with a digital MIL gauge and the orange peel with a digital wave scan device.

15.A

Boise Mobile Equipment
08/30/22
43 The body shall be painted using a single color to match the cab primary color, and then shall be buffed to a high gloss finish.

Pump, plumbing and tank cargo space to be finished in Black truck bed liner.

INTERIOR COMPARTMENT FINISH
The interior of the compartments shall be finish painted with Multispec #7251 Gray Stone scuff resistant paint to provide a protective application over all of the compartment interior surfaces.

TOUCH-UP PAINT
Touch-up paint and activator shall be furnished with the completed truck at final delivery.

CAB GOLD LEAF LETTERING
The cab lettering shall be gold leaf material, shaded in black and encapsulated in clear Mylar. Letters shall be placed on the cab.

LETTERING, STRIPING, SCOTCH-LITE PACKAGE

LETTERING ON FRONT CAB DOORS
Gold leaf, "Real Gold" vinyl, with drop shadow lettering shall be provided on the cab drivers and officer's doors per the fire department requirements.

The design of the lettering on the cab doors shall be designed to fit in the 496 sq. inches available.

3" LETTERING ON FRONT CAB DOORS
Lettering provided on the driver's and officer's cab doors shall be 3" high.

FRONT CAB DOOR TEXT LINE 1 - CITY OF HEMET FRONT CAB DOOR TEXT LINE 2 - FIRE

DEPARTMENT FRONT CAB DOOR LETTERING TOP LINE ARCED

LETTERING ON REAR CAB DOORS
Gold leaf, "Real Gold" vinyl, with drop shadow lettering shall be provided on the cab drivers and officer's doors per the fire department requirements.

The design of the lettering on the cab doors shall be designed to fit in the 496 sq. inches available.

REAR CAB DOOR TEXT LINE 1 - ###
REAR CAB DOOR TEXT LINE 2 - PARAMEDIC
3" LETTERING ON REAR CAB DOOR
Lettering provided on the front of cab shall be 3" high.

15.A

Boise Mobile Equipment
08/30/22
44 LETTERING ON REAR BODY
Scotch-Lite with drop shadow lettering shall be provided on the rear body panel per the fire department requirements.

The design of the lettering on the rear of the body shall be designed to fit in the 167 sq. inches available.

3" LETTERING ON REAR BODY
Lettering provided on the rear body panel shall be 3" high.

REAR BODY TEXT LINE 1 - HMT
REAR BODY TEXT LINE 2 - REAR BODY
TEXT LINE 3 –

CAB ROOF LETTERING
Scotch-Lite without drop shadow lettering shall be provided on the cab roof per the fire department requirements.

The design of the lettering on the cab roof shall be designed to fit in the 2500 sq. inches available. 24" LETTERING ON CAB ROOF
Lettering provided on the cab roof shall be 24" high per Hemet Fire Department and engineering design.

CAB ROOF TEXT LINE 1 - HMT ###
CAB ROOF TEXT LINE 2 –

SCOTCH-LITE STRIPE
A four (4) inch high "Scotch-Lite" stripe shall be provided.

The stripe shall be applied on a minimum of 60 percent of each side of the unit, 60 percent on the rear of the unit and 40 percent on the front of the unit.

The Scotch-Lite stripe layout shall be determined by the Hemet Fire Department.

BLACK SCOTCH-LITE
The Scotch-Lite shall be black in color.

4" SCOTCH-LITE "Z" IN STRIPE
A four (4) inch simple "Z" effect shall be incorporated into the Scotch-Lite scheme on the body.

Final layout of this configuration shall be determined by the Hemet Fire Department.

COMPARTMENT DOOR EDGE STRIPING
The hinged compartment doors shall have a red and white 3M Diamond Grade reflective stripe applied on the edges. The stripe shall be a 1-1/2" minimum in width.

15.A

Boise Mobile Equipment
08/30/22
45 CHEVRON STRIPING
The entire rear of the truck shall be covered with alternating strips of reflective striping.

SUCTION HOSE
Three (3) 2.5” x 8 foot lengths of Kochek PVC flexible suction hose shall be provided and equipped with lightweight couplings.

WHEEL CHOCKS
Two (2) Zico Model AC-1, aluminum wheel chocks shall be provided on the apparatus. 5# DRY CHEMICAL FIRE EXTINGUISHER
One (1) 5# ABC dry chemical fire extinguisher and mounting bracket shall be provided on the apparatus. The extinguisher shall have a pressure gauge and shall be filled with a dry chemical extinguishing agent.

REFLECTOR
A set of three (3) triangular reflectors shall be provided.

UNDERBODY CORROSION TREATMENT
Upon apparatus completion, underside of the apparatus, from the pump enclosure-back, shall have anti corrosion film applied to help inhibit rust and the corrosion process. The semi-firm wax film shall be applied by air spray method. The film shall be applied as a minimum to the following areas: body substructure, underside of all body compartments, running board supports and rear step supports. No film shall be applied directly to the exhaust system or wheel wells.

NOTE: The film shall remain semi-firm to promote self-sealing. The film may leave a light tinted color to those areas treated.

Concession

15.A

18.4°
24-3/4"
90-1/4"

28.5°
ASSY
3 L
H
11 C
G
14 10 71 12
D
2 F
5 J
9 B
6 13 4 15
A
E
K
8 54 8 13 6 71 12 2 11 9 15 3 10 14
B
H
C
A
E
L
F
D
K
G
J
16 16
17 17
18 18
19 19
20 20
21 21
22 22
23 23
MM
NN
PP
QQ
MATERIAL:

BME FIRE TRUCKS
4600 S. APPLE ST, BOISE, ID 83716
---
ENG APPR:

XX/XX/XX
ES
MDL'D BY:
06/15/2022
DRWN BY:

AG
AG
49028.98
02/04/2022
DATE DESCRIPTION: INITIALS
MFG APPR:

WWW.BMEFIRE.COM (800) 445-8342
ASHEET 1 OF 1
AP-00-014655

DO NOT SCALE DRAWING
.005 THREE PLACE DECIMAL
.020 TWO PLACE DECIMAL
1 TRUCKS.

WEIGHT: THICKNESS:

MATERIAL SIZE:

PART NO:

REV:

WRITTEN CONSENT OF BME FIRE

ILLUSTRATED WITHOUT THE

UNLESS OTHERWISE SPECIFIED

DIMENSIONS ARE IN INCHES
TOLERANCES:

FRACTIONAL 1/16
ANGULAR: MACH .5 BEND

PROPRIETARY AND CONFIDENTIAL

THIS DRAWING IS THE PROPERTY
OF BME FIRE TRUCKS. ITS

SUBMISSION DOES NOT INCLUDE

OR CARRY THE RIGHT TO MAKE,

USE OR SELL WHAT IS
TYPE 6 - GLENDALE
(SUMTER) TOP LEVEL
MTL P/N:

DRIVER'S STORAGE COMPARTMENTS

LETTER WIDTH (W) HEIGHT (H) DEPTH (D) CAPACITY
D1 26.00 44.00 20.00 15.17
D2 72.00 22.00 20.00 20.10
D3 23.00 17.00 20.00 5.51

0.00 TOTAL (CUBIC FEET) 40.78

PASSENGER'S STORAGE COMPARTMENTS

LETTER WIDTH (W) HEIGHT (H) DEPTH (D) CAPACITY
P1 26.00 44.00 20.00 15.17
P2 44.00 22.00 20.00 12.62
P3 23.00 44.00 20.00 13.61

0.00 TOTAL (CUBIC FEET) 41.40
D1
96"

BODY WIDTH
P2 P1 P3
111-1/4"

BODY LENGTH
59"

BODY HEIGHT
D2
D3
173-1/2"
60-1/4"
274-3/4"
104"

15.A

FORM E - PUBLISHED OPTIONS Procurement No.:

Offeror Name:
1) Bid each Option on a single separate line. Bidder is responsible to identify each item with a specific code or part number.
2) Use a single Form E for ALL items. Add/Insert additional lines as necessary. 3) Completely describe each option, including manufacturer's code or part numbers as appropriate. Each item listed MUST have a unique code or part number.
4) Options which replace standard equipment on a base bid Item on Form D should be priced net of any credit due for the replaced item.
5) Options which are shown as upgrades/downgrades of a base bid item on Form D should be priced at the differential amount between the base bid item and the option.
6) You encouraged to offer specific manufacturer's catalogs (eg. Whelan, Fed Signal, etc.) as options, with 'List Less' or 'Cost Plus' percentages for pricing. Copy of catalog should be supplied w/bid.

Code or
Part No. Option Description 2022 Pricing
FS19DB07/FS19DB09/FS19DD01 CHASSIS OPTIONS
X5H SUPERCAB UPGRADE $3,067.00
663A UPGRADE TO XLT PACKAGE $3,088.00
F4G DOWNGRADE TO F450 -$1,125.00
99Y DOWNGRADE TO 6.8L V-10 ENGINE -$6,975.00
86S LOW DEFLECTION PACKAGE $105.00
52B ELEC BRAKE CONTROLLER $285.00
525 CRUISE CONTROL $291.00
585 AM/FM/CD $353.00
67A DUAL ALTERNATORS $470.00
62R PTO PROVISION $347.00
S2Z CHROME GRILLE FOR XL CHASSIS [ REG 17F XL DÉCOR ] $427.00 68R MANUAL REGENERATION $309.00
16S ALL WEATHER FLOOR MATS $93.00
166 CARPET DELETE -$45.00
18B MOLDED CAB STEPS $458.00
213 ELECTRONIC SHIFT ON FLY $309.00
18B MOLDED BLACK CAB STEPS $396.00
41P SKID PLATES $124.00
512 SPARE TIRE/ WHEEL $433.00
535 HI CAP TRAILER TOW $433.00
64D POLISHED ALUMINUM WHEELS $1,355.00
87D AMBER STROBE LIGHTS [4] $866.00
76S REMOTE START $241.00
945 STAINLESS STEEL WHEEL SIMULATORS $588.00
942 DAYTIME RUNNING LIGHTS $56.00
96V XL VALUE PACKAGE $736.00
90L POWER EQUIPMENT GROUP [ ON XL ] $1,231.00
PATS ADDITIONAL CHIP KEY WITH KEY FOB / INCL PROGRAMMING $217.00 SCBA-O H.O. BOSTRUM OFFICER SCBA SEAT $1,231.00
SCBA-1 1 REAR H.O. BOSTRUM SCBA SEAT $1,231.00
SCBA-2 2 REAR H.O. BOSTRUM SCBA SEATS $2,221.00
SCBA-3 3 REAR H.O. BOSTRUM SCBA SEATS $2,964.00
SHPTHR SHIP THRU FREIGHT FOR NFPA EQUIPMENT $309.00
SP101 SPECIAL ORDER PAINT FROM SPO PAINT CHART $860.00
176WB 176"WB/102"CA/70"AF/285"OAL $155.00
182WB 182" WB / 108" CA / 70" AF / 291" OAL $217.00
194WB 194"WB/120"CA/75"AF/308"OAL $402.00
200WB 200" WB / 126" CA / 75" AF / 314" OAL $606.00
212WB 212 " WB / 138" CA / 81" AF / 332" OAL $637.00
218WB 218" WB / 144" CA / 81" AF / 338" OAL $681.00
224WB 224" WB / 150" CA / 87" AF / 350" OAL $705.00
230WB 230"WB / 156" CA / 87" AF / 356" OAL $724.00
242WB 242" WB / 168" CA / 100" AF / 381" OAL $996.00
260WB 260" WB / 186" CA / 120" AF /419" OAL $1,194.00
281WB 281" WB / 207" CA / 120" AF / 440" OAL $1,423.00
Note: Bidder must identify each option bid with an identifying Code or Part No. that should be referenced on all Contract Pricing Worksheets
Notes:
(Important)

15.A

536 FRAME, SINGLE CHANNEL, STRAIGHT 'C' 14.18 SM / 120,000 PSI $452.00 539 FRAME, SINGLE CHANNEL, STRAIGHT 'C' 20.11 SM / 120,000 PSI $1,132.00 412 OUTER 'C' CHANNEL REINFORCEMENT, 29.84 SM / 120,000 PSI $1,436.00 15S FRONT STABILIZER BAR $606.00
532 FRONT FRAME EXTENSION 20" $606.00
765 CHROME PLATED FRONT BUMPER $606.00
86C CHROME GRILLE $303.00
60A LUBE FRONT AXLE, SYNTHETIC OIL, EMGARD 50W $62.00
91D SWITCHBACK EXHAUST WITH VERTICAL EXHAUST $681.00
69C 55 GALLON ALUMINUM FUEL TANK $377.00
65E 65 GALLON ALUMINUM FUEL TANK $526.00
65F 65L / 55R DUAL ALUMINUL FUEL TANKS $1,132.00
476 21,000 SINGLE REDUCTION LOCKING REAR AXLE $2,265.00 477 21,000 DUEAL REDUCTION AXLE $1,739.00
479 23,000 SINGLE REDUCTION AXLE $2,871.00
47P 23,000 SINGLE REDUCTION LOCKING REAR AXLE $2,599.00 47X 26,000 SINGLE REDUCTION REAR AXLE $3,026.00
52P DRIVE SHAFT UPGRADE $229.00
68R 23,000 LB MULTI LEAF SPRINGS W/ 2000 LB AUXILIARY $285.00 68T 31,000 LB MULTI LEAF SPRINGS W/ 2000 LB AUXILIARY $606.00 68B 21,000 LB REAR AIR SUSPENSION W/ SINGLE LEVELING VALVE $755.00 68F 23,000 LB REAR AIR SUSPENSION W/ SINGLE LEVELING VALVE $1,132.00 68Z AIR SUSPENSION DUMP VALVE $155.00
68Y AIR SUSPENSION LEVELING VALVE, DUAL HEIGHT $408.00
961 SHOCK ABSORBERS, REAR, DOUBLE ACTING $204.00
607 REAR AXLE LUBE, SYNTHETIC, EMGARD 75W-90 $124.00
184 PARKING BRAKE, BOSCH DSSA TYPE, 12X3, IP, SPRING ACTUATED $489.00 62F BRAKE CHAMBER SPRING RELOCATED $50.00
152 TRAILER CONN SOCKET, 7-WAY, WIRED FOR TURN AND STOP $124.00 154 TRAILER CONN SOCKET, 7-WAY, WIRED FOR TURN, NO STOP $124.00 158 TRAILER AIR BRAKE PACKAGE, 4 WHEEL $452.00
90P POWER EQUIPMENT GROUP [ ON XL ] $582.00
92S SLIDING REAR WINDOW $155.00
21D FORD SYNC $489.00
90C FORD TELEMANTICS $990.00
16V VOLTMETER $124.00
86K KEYLESS ENTRY $210.00
90E EXTERIOR APPEARANCE GROUP $903.00
59A AIR HORN $111.00
54F MIRRORS; POWER TRAILER TOW $489.00
19A AMBULANCE PREP PACKAGE $1,590.00
17M BACK UP ALARM, ELECTRIC, 101 dBA $136.00
59B BODY BUILDER SPECIAL WIRING HARNESS $74.00
59C BODY BUILDER WIRING TO END OF FRAME $167.00
962 DAYTIME RUNNING LIGHTS $56.00
164 FENDER MOUNTED FRONT AND REAR FACING TURN SIGNALS $110.00 17A 220 AMP DENSCO SC6 HD ALTERNATOR $272.00
17D DUAL HD ALTERNATORS 357 AMP CAPACITY [ 200 AMP & 157 AMP ] $1,058.00 55M JUMP START STUD, REMOTE $111.00
63B [2] 900 CCA, 12V, MOTORCRAFT BATTERIES $74.00
63D [3] 900 CCA, 12V, MOTORCRAFT BATTERIES $309.00
63E [2] 625 CCA, 12V, MOTORCRAFT BATTERIES, TEMP MOUNTED N/C 643 22 X 8.25 10 HOLE FRONT WHEELS $31.00
663 22 X 8.25 10 HOLE REAR WHEELS $62.00
TC3 MICHELIN 11R22.5H FRONT TIRES $514.00
TDG CONTINENTAL 295/60R22.5H FRONT TIRES $489.00
RC3 MICHELIN 11R22.5H REAR TIRES $514.00
RDG CONTINENTAL 295/60R22.5H REAR TIRES $489.00
88Y 40/20/40 SEAT $489.00
88J 30/0/30 SIR RIDE DRIVER AND PASSENGER $1,058.00
88G VINYL DRIVER AIR RIDE SEAT W/ INTEGRAL AIR PUMP $489.00 88R VINYL AIR RIDE DRIVER SEAT, W/ INTEGRAL AIR PUMP $545.00 925 SLIDING REAR WINDOW W/ PRIVACY GLASS $278.00
86B GRILLE, FIXED, DARK SHADOW GREY -$31.00
59A HORN, AIR - BLACK, SINGLE TRUMPET $62.00
58X RADIO DELETE -$62.00
58Y RADIO AM/FM STEREO W/ 6 DISC CD CHANGER $613.00
52A STEERING WHEEL, BLACK 2-SPOKE, 15.5" DIAMETER N/C

15.A

52B STEERING WHEEL, TWO SPOKE, BLACK LEATHER WRAPPED, 15.5" $93.00 644 WHEELS, FRONT 22.5 X 8.25, POLISHED ALUMINUM, 10 HOLE $712.00 664 WHEELS, REAR 22.5 X 8.25, POLISHED ALUMINUM, 10-HOLE $1,330.00 31P SHIP THRU PDI [FOR CHASSIS BEING DELIVERED TO BODY CO] $278.00 MARM1 4WD CONVERSION THROUGH MANNING $40,528.00
FLR1 FLOOR PLAN INTEREST 21/Day
SHOP1 WRITTEN SHOP MANUAL $464.00
SHOP2 ELECTRICAL WIRING DIAGRAM $241.00
SHOP3 EMISSIONS AND DIAGNOSTICS MANUAL $241.00
SHOP4 SHOP MANUAL ON DVD $464.00
SHOP5 PARTS DVD $464.00
FS19DB01/FS19DB03/FS19DB05/FS19DB12/FS19DC02/FS19DC0
4/FS19DD03/FS19DE02/FS19DE04/FS19DE06 INTERNATIONAL

CHASSIS OPTIONS
INT-001 Day Cab in lieu of Crew Cab -$7,200.00
INT-002 Crew Cab in lieu of Day Cab $9,120.00
INT-003 Upgrade to 350hp (Only available in 4X2 Model) $7,351.00 INT-004 Upgrade to 370hp (SCR only—4X2 Model) $7,895.00 INT-005 Upgrade to 385hp (SCR only- 4X2 Model) $8,440.00 INT-006 Average Spare Tire w/ Wheel $762.00
INT-007 Cost to Increase Wheel Base $572.00
INT-008 Front Axle 14,000 in lieu of 12,000 (Non-Drive) $354.00 INT-009 Front Axle 16,000 in lieu of 12,000 (Non-Drive) $1,463.00 INT-010 Front Axle 18,000 in lieu of 12,000 (Non-Drive) $1,715.00 INT-011 Front Axle 20,000 in lieu of 12,000 (Non-Drive) $2,028.00 INT-012 Front Axle 14,000 in lieu of 12,000 (Drive) $858.00 INT-013 Front Axle 16,000 in lieu of 12,000 (Drive) $3,948.00 INT-014 Front Axle 18,000 in lieu of 12,000 (Drive) $6,534.00 INT-015 Upgrade to 4X4 in lieu of 4X2 (Daycab) $18,513.00 INT-016 Upgrade to 240amp alternator in lieu of 200amp $327.00 INT-017 Upgrade to 320amp alternator in lieu of 200 amp $1,729.00 INT-018 CD Shop Manuals $504.00
INT-019 Polished Aluminum Wheel in lieu of Steel(Cost per Wheel) $381.00 INT-020 Auxiliary Engine Water Cooler $1,035.00
INT-021 Engine Oil Temperature Gauge $123.00
INT-022 Rear Axle Oil Temperature Gauge $177.00
INT-023 Upgraded 16.5 CFM Air Compressor $572.00
INT-024 Polished Aluminum Air Tanks $906.00
INT-025 Tilt/Telescopic Steering Wheel $640.00
INT-026 Fog Lights $313.00
INT-027 Remote Jump Start Stud $286.00
INT-028 Upgraded Bluetooth Radio $585.00
INT-029 Hood Hatch for Servicing $783.00
INT-030 Bright Finish Stainless Steel Fuel Tank Straps $531.00 FS19DB02/FS19DB04/FS19DB06/FS19DC01/FS19DC03
FS19DD02/ FS19DE01/FS19DE03/FS19DE05 FREIGHTLINER

CHASSIS OPTIONS
101-2XM UPGRADE to Cummins ISL 350HP in Lieu of 330HP $495.00 400-1BA UPGRADE, Front Axle From 14,000# to 18,000# $2,768.00 420-022 UPGRADE, Rear Axle From 26,000# to 27,000# $124.00 829-075 Extended Cab in lieu of Crew Cab -$3,713.00
829-075 Extended Cab in lieu of Day Cab $6,456.00
829-071 Day Cab in lieu of Crew Cab -$9,858.00
829-079 Crew Cab in lieu of Day Cab $10,844.00
SVC-CD Service CD $322.00
CPC-CD Custom Parts CD $322.00
CPC-SVC-CD Custom Parts & Service CD $631.00
FS19DB01 / FS19DB02 OPTIONS

PLUMBING OPTIONS
08-11-1100 UPGRADE Pump, Darley, JMP500, 2/Stg, PTO $8,567.00

ELECTRICAL OPTIONS
40-15-3300 Battery Charger, Kussmaul, Autocharge 1000, #091-56-12 $929.00 40-15-3400 Battery Charger, Kussmaul, Autocharge 1200, #091-53-12 $1,690.00 40-15-3910 Battery Charger, Kussmaul, Bar Graph Display, #091-94-12 $220.00 40-15-5200 Shore Power Plug, Kussmaul Auto-Eject #091-18WP-120, 15 Amp $479.00 40-15-5300 Shore Power Plug, Kussmaul Auto-Eject #091-20WP-120, 20 Amp $505.00 40-15-5400 Shore Power Plug, Kussmaul Auto-Eject #091-159-30B-120, 30 A $741.00 41-44-3060 UPGRADE Compartment Lighting, Whelen, Fluorent Series $2,599.00 40-32-5050 Stop/Tail Light, Whelen #60R00FRR, LED, 4" x 6" (1) THIRD BRAKE LIGHT $358.00 41-36-3100 Scene Light, Whelen, LED, 4"x 6" (EACH) $394.00 41-36-5100 Scene Light, Whelen, LED, 7"x 9" (EACH) $547.00

15.A

41-36-5200 Scene Light, Whelen, PFP1, LED, (EACH) $1,416.00 41-21-2200 Spotlight, Cab, GO-LIGHT, 2020#, 12V $598.00 42-10-2000 Radio Antenna, Installation (EACH) $124.00 42-10-3600 Radio, Fire, Installation, Purchaser Supplied (EACH) $248.00 42-21-1100 12V Power Outlet, 20 Amp, Cab Dash (EACH) $69.00 42-21-1110 12V Power Outlet, 20 Amp, Console (EACH) $69.00 43-10-2100 Back Up Camera, Tear Drop W/Monitor $1,320.00

BODY / COMPARTMENT OPTIONS
24-03-4100 UPGRADE Fenderettes, Body, Polished S/S, 22.5" rims (2) Single Axle $275.00 24-05-1700 SCBA Stge, LH Fwd Whlwell, 8" Rnd, Cast Prod Door $309.00 24-05-2300 SCBA Stge, LH Rear Whlwell, 8" Rnd, Cast Prod Door $309.00 24-05-5700 SCBA Stge, RH Fwd Whlwell, 8" Rnd, Cast Prod Door $309.00 24-05-6300 SCBA Stge, RH Rear Whlwell, 8" Rnd, Cast Prod Door $309.00 35-10-0110 DELETE Shelf, Adjustable, Alum 1/8" (EACH) -$225.00 35-10-0110 Shelf, Adjustable, Alum 1/8" (EACH) $248.00 35-30-2130 Slide Out Tray, ExtendoBed, 1500# (EACH) $2,557.00 35-20-1100 Slide Tray, 250#, Alum 3/16", <24"D (EACH) $481.00 35-25-1120 Slide Tray, BME 500#, Alum 3/16", <24"D (EACH) $536.00 35-50-1100 Tool Board, .250" Alum (EACH) $220.00 35-85-1100 Turtle Tile, Grating, Per Square Foot $31.00 35-85-2100 Dri-Dek, Grating, Per Square Foot $32.00

PAINT OPTIONS
80-01-1230 UPGRADE Paint, Cab/Chassis, 4 Door Commercial, Two Tone $6,050.00 80-01-3300 Paint, Chassis Wheels, Six (6), Job Color $1,238.00 81-20-2350 Striping Package, Custom Contact Factory FS19DB03 / FS19DB04 OPTIONS

PLUMBING OPTIONS
05-15-2100 UPGRADE PUMP, Hale, TBP, PTO, 2-Stg, 750GPM $5,808.00 08-15-1800 DELETE Pump, Darley, 1-1/2AGE, 24HP Kubota -$20,862.00

ELECTRICAL OPTIONS
40-05-1250 UPGRADE Electrical, Multi-Plex, Weldon V-MUX $6,435.00 40-15-3300 Battery Charger, Kussmaul, Autocharge 1000, #091-56-12 $929.00 40-15-3400 Battery Charger, Kussmaul, Autocharge 1200, #091-53-12 $1,690.00 40-15-3910 Battery Charger, Kussmaul, Bar Graph Display, #091-94-12 $220.00 40-15-5200 Shore Power Plug, Kussmaul Auto-Eject #091-18WP-120, 15 Amp $479.00 40-15-5300 Shore Power Plug, Kussmaul Auto-Eject #091-20WP-120, 20 Amp $505.00 40-15-5400 Shore Power Plug, Kussmaul Auto-Eject #091-159-30B-120, 30 A $741.00 40-20-1200 Load Manager, Class 1, TSM, #101540, Negative Output $990.00 41-44-3060 UPGRADE Compartment Lighting, Whelen, Fluorent Series $2,599.00 41-36-3100 Scene Light, Whelen, LED, 4"x 6" (EACH) $394.00 41-36-5100 Scene Light, Whelen, LED, 7"x 9" (EACH) $547.00 41-36-5200 Scene Light, Whelen, PFP1, LED, (EACH) $1,416.00 41-21-2200 Spotlight, Cab, GO-LIGHT, 2020#, 12V $598.00 42-10-2000 Radio Antenna, Installation (EACH) $124.00 42-10-3600 Radio, Fire, Installation, Purchaser Supplied (EACH) $248.00 42-21-1100 12V Power Outlet, 20 Amp, Cab Dash (EACH) $69.00 42-21-1110 12V Power Outlet, 20 Amp, Console (EACH) $69.00 43-10-2100 Back Up Camera, Tear Drop W/Monitor $1,320.00 45-35-1200 Traffic Emitter, Opticom, Roof Mounted $2,392.00

BODY / COMPARTMENT OPTIONS
24-03-4100 UPGRADE Fenderettes, Body, Polished S/S, 22.5" rims (2) Single Axle $275.00 35-10-0110 DELETE Shelf, Adjustable, Alum 1/8" (EACH) -$225.00 35-10-0110 Shelf, Adjustable, Alum 1/8" (EACH) $248.00 24-09-1100 Ventilation, Fixed Louvers, Body (EACH) $41.00 24-09-2100 Ventilation, 120V Elec, w/Timer, Cmpt (EACH) $385.00 35-30-2130 Slide Out Tray, ExtendoBed, 1000# (EACH) $1,870.00 35-20-1100 Slide Tray, 250#, Alum 3/16", <24"D (EACH) $481.00 35-25-1120 Slide Tray, BME 500#, Alum 3/16", <24"D (EACH) $536.00 35-50-1100 Tool Board, .250" Alum (EACH) $220.00 35-85-1100 Turtle Tile, Grating, Per Square Foot $31.00 35-85-2100 Dri-Dek, Grating, Per Square Foot $32.00 $0.00
PAINT OPTIONS $0.00
80-01-1230 UPGRADE Paint, Cab/Chassis, 4 Door Commercial, Two Tone $6,050.00 80-01-3300 Paint, Chassis Wheels, Six (6), Job Color $1,238.00 81-20-2350 Striping Package, Custom Contact Factory FS19DB05 / FS19DB06 OPTIONS

PLUMBING OPTIONS

15.A

NONE

ELECTRICAL OPTIONS
40-05-1250 UPGRADE Electrical, Multi-Plex, Weldon V-MUX $6,435.00 40-15-3300 Battery Charger, Kussmaul, Autocharge 1000, #091-56-12 $929.00 40-15-3400 Battery Charger, Kussmaul, Autocharge 1200, #091-53-12 $1,690.00 40-15-3910 Battery Charger, Kussmaul, Bar Graph Display, #091-94-12 $220.00 40-15-5200 Shore Power Plug, Kussmaul Auto-Eject #091-18WP-120, 15 Amp $479.00 40-15-5300 Shore Power Plug, Kussmaul Auto-Eject #091-20WP-120, 20 Amp $505.00 40-15-5400 Shore Power Plug, Kussmaul Auto-Eject #091-159-30B-120, 30 Amp $741.00 41-44-3060 UPGRADE Compartment Lighting, Whelen, Fluorent Series $2,599.00 40-20-1200 Load Manager, Class 1, TSM, #101540, Negative Output $990.00 40-32-5050 Stop/Tail Light, Whelen #60R00FRR, LED, 4" x 6" (1) THIRD BRAKE LIGHT $358.00 43-10-2100 Back Up Camera, Tear Drop W/Monitor $1,320.00

BODY / COMPARTMENT OPTIONS
24-03-4100 UPGRADE Fenderettes, Body, Polished S/S, 22.5" rims (2) Single Axle $275.00 35-10-0110 DELETE Shelf, Adjustable, Alum 1/8" (EACH) -$225.00 35-10-0110 Shelf, Adjustable, Alum 1/8" (EACH) $248.00 24-09-1100 Ventilation, Fixed Louvers, Body (EACH) $41.00 24-09-2100 Ventilation, 120V Elec, w/Timer, Cmpt (EACH) $385.00 35-30-2130 Slide Out Tray, ExtendoBed, 1000# (EACH) $1,870.00 35-20-1100 Slide Tray, 250#, Alum 3/16", <24"D (EACH) $481.00 35-25-1120 Slide Tray, BME 500#, Alum 3/16", <24"D (EACH) $536.00 35-50-1100 Tool Board, .250" Alum (EACH) $220.00 35-85-1100 Turtle Tile, Grating, Per Square Foot $31.00 35-85-2100 Dri-Dek, Grating, Per Square Foot $32.00

PAINT OPTIONS
80-01-1230 UPGRADE Paint, Cab/Chassis, 4 Door Commercial, Two Tone $6,050.00 80-01-3300 Paint, Chassis Wheels, Six (6), Job Color $1,238.00 81-20-2350 Striping Package, Custom Contact Factory FS19DB07 / FS19DB08 OPTIONS

PLUMBING OPTIONS
05-20-3100 Pump Change To, Hale HPX-200-B18, 18HP, B&S Gasoline -$7,749.00 07-09-1450 Pump Change To, Waterous, E511-C, 24HP, Kubota Diesel -$281.00 08-15-1400 Pump Change To, Darley, 1-1/2AGE 18HP, Honda Gasoline -$4,298.00 08-04-7200 UPGRADE, CAFS System, Odin, Mongoose, Diesel, 46/23 $28,463.00 13-10-1100 Foam System, FoamPro 1600 $6,380.00
13-10-1110 Foam System, FoamPro 1601 $6,449.00
13-10-5200 Foam System, FoamPro, On-Off Switch in Cab $467.00 13-11-1100 Foam Upload System, BME $1,279.00 13-11-2000 Foam Pump, FoamPro, 12V Elec, (A) Refill Transfer $3,017.00 12-13-1200 Bumper Dschrg, 1-1/2", Front, Swivel, Left Side $1,650.00 12-13-1300 Bumper Dschrg, 1-1/2", Front, Swivel, Right Side $1,650.00 13-06-2100 Foam System, Around-the-Pump, FRC, Manual, Class A $1,553.00 13-13-1050 Discharge, Class A, Discharge (PER OUTLET) $358.00 14-40-5100 Foam Tank Gauge, FRC, Class A, Pump Panel $651.00 14-40-5300 Foam Tank Gauge, FRC, Class A, Mini, Cab $474.00 12-05-4100 Fog Nozzle, Elkhart, 3/4", Fixed (EACH) $1,078.00 29-05-1100 Foam Tank Capacity, 12 Gallons, Class A, Poly $544.00

BODY / COMPARTMENT OPTIONS
24-03-3200 UPGRADE Fenderettes, Body, Polished S/S, (2) 16"/19" rims $275.00 35-10-0110 Shelf, Adjustable, Alum 1/8" (EACH) $248.00 35-20-1100 Slide Tray, 250#, Alum 3/16", <24"D (EACH) $481.00 35-30-2280 ExtendoBed, "Scott Command" Carrier (Requires Option #35-30-2350 or 35-30-2370) $4,570.00 35-30-2290 ExtendoBed, "Colorado" Carrier (Requires Option #35-30-2350 or 35-30-2370) $1,563.00 35-30-2300 ExtendoBed, "Portville" Carrier (Requires Option #35-30-2350 or 35-30-2370) $3,323.00 35-30-2270 ExtendoBed, "Orange County" Carrier (Requires Option #35-30-2350 or 35-30-2370) $4,318.00 35-30-2280 ExtendoBed, "Scott Command" Carrier (Requires Option #35-30-2350 or 35-30-2370) $4,570.00 35-30-2290 ExtendoBed, "Colorado" Carrier (Requires Option #35-30-2350 or 35-30-2370) $1,563.00 35-30-2300 ExtendoBed, "Portville" Carrier (Requires Option #35-30-2350 or 35-30-2370) $3,323.00 35-30-2310 ExtendoBed, "Oklahoma" Carrier (Requires Option #35-30-2350 or 35-30-2370) $7,054.00 35-30-2320 ExtendoBed, "ATF" Carrier (Requires Option #35-30-2350 or 35-30-2370) $2,666.00 35-30-2330 ExtendoBed, "Federal" Carrier (Requires Option #35-30-2350 or 35-30-2370) $4,517.00 35-30-2340 ExtendoBed, "2 Stage Professional" Carrier $1,210.00 35-30-2350 ExtendoBed, "Professional" Carrier, (EBL-1072), #1000 Capacity $2,243.00 35-30-2360 ExtendoBed, "HD Slideout" Carrier $3,484.00 35-30-2370 ExtendoBed, EB-1575, #1500 Capacity, 110% Extension $2,553.00 35-30-2380 ExtendoBed, "West Carrol" Carrier (Requires Option #35-30-2350 or 35-30-2370) $1,435.00 35-25-1120 Slide Tray, BME 500#, Alum 3/16", <24"D (EACH) $536.00 35-50-1100 Tool Board, .250" Alum (EACH) $220.00

15.A

35-85-1100 Turtle Tile, Grating, Per Square Foot $31.00 35-85-2100 Dri-Dek, Grating, Per Square Foot $32.00

ELECTRICAL OPTIONS
40-15-3300 Battery Charger, Kussmaul, Autocharge 1000, #091-56-12 $929.00 40-15-3400 Battery Charger, Kussmaul, Autocharge 1200, #091-53-12 $1,690.00 40-15-3910 Battery Charger, Kussmaul, Bar Graph Display, #091-94-12 $220.00 40-15-5200 Shore Power Plug, Kussmaul Auto-Eject #091-18WP-120, 15 Amp $479.00 40-15-5300 Shore Power Plug, Kussmaul Auto-Eject #091-20WP-120, 20 Amp $505.00 40-15-5400 Shore Power Plug, Kussmaul Auto-Eject #091-159-30B-120, 30 A $741.00 40-20-1200 Load Manager, Class 1, TSM, #101540, Negative Output $990.00 40-20-1700 Low Voltage Alarm, Class 1, #100545, 12V, light/buzzer $557.00 41-44-3060 UPGRADE Compartment Lighting, Whelen, Fluorent Series $2,599.00 40-32-5050 Stop/Tail Light, Whelen #60R00FRR, LED, 4" x 6" (1) THIRD BRAKE LIGHT $358.00 41-15-1600 Map Light, Havis Shields #C-MAP-T-LED, 12" LED $179.00 41-21-2200 Spotlight, Cab, GO-LIGHT, 2020#, 12V $598.00 42-10-2000 Radio Antenna, Installation (EACH) $124.00 42-10-3600 Radio, Fire, Installation, Purchaser Supplied (EACH) $248.00 42-21-1100 12V Power Outlet, 20 Amp, Cab Dash (EACH) $69.00 42-21-1110 12V Power Outlet, 20 Amp, Console (EACH) $69.00 43-10-2100 Back Up Camera, Tear Drop W/Monitor $1,320.00 45-35-1200 Traffic Emitter, Opticom, Roof Mounted $2,392.00 46-05-1500 Traffic Advisor, Whelen, TAL65, 36", LED $859.00 46-05-1600 Traffic Advisor, Whelen, TA837L, 43", LED $893.00 46-05-5100 Traffic Arrow Light, 911EP, TD-WL36A $867.00

FRONT BUMPER OPTIONS
60-05-1600 Winch, Electric, Front Mount, 9,000#, Warn $2,592.00 60-05-1700 Winch, Electric, Front Mount, 12,000#, Warn $3,295.00 60-25-1500 Buckstop Bumper / Grill Guard, W/Winch Provisions $3,058.00 60-35-1300 Receiver, Front, Winch/Rope, 12,000# $784.00

PAINT OPTIONS
80-01-1230 UPGRADE Paint, Cab/Chassis, 4 Door Commercial, Two Tone $6,050.00 80-01-3300 Paint, Chassis Wheels, Six (6), Job Color $1,238.00 81-20-2350 Striping Package, Custom Contact Factory

CHASSIS OPTIONS BY BOISE MOBILE EQUIPMENT
02-88-9500 Super Single Conversion, DRW to SRW $7,697.00 FS19DB09 / FS19DB10 OPTIONS

PLUMBING OPTIONS
05-20-3100 Pump Change To, Hale HPX-200-B18, 18HP, B&S Gasoline -$7,749.00 07-09-1450 Pump Change To, Waterous, E511-C, 24HP, Kubota Diesel -$281.00 08-15-1400 Pump Change To, Darley, 1-1/2AGE 18HP, Honda Gasoline -$4,298.00 13-10-1100 Foam System, FoamPro 1600 $6,380.00
13-10-1110 Foam System, FoamPro 1601 $6,449.00
13-10-5200 Foam System, FoamPro, On-Off Switch in Cab $467.00 13-11-1100 Foam Upload System, BME $1,279.00 13-11-2000 Foam Pump, FoamPro, 12V Elec, (A) Refill Transfer $3,017.00 12-13-1200 Bumper Dschrg, 1-1/2", Front, Swivel, Left Side $1,650.00 12-13-1300 Bumper Dschrg, 1-1/2", Front, Swivel, Right Side $1,650.00 13-06-2100 Foam System, Around-the-Pump, FRC, Manual, Class A $1,553.00 13-13-1050 Discharge, Class A, Discharge (PER OUTLET) $358.00 14-40-5100 Foam Tank Gauge, FRC, Class A, Pump Panel $651.00 14-40-5300 Foam Tank Gauge, FRC, Class A, Mini, Cab $474.00 12-05-4100 Fog Nozzle, Elkhart, 3/4", Fixed (EACH) $1,078.00 29-05-1100 Foam Tank Capacity, 12 Gallons, Class A, Poly $544.00

BODY / COMPARTMENT OPTIONS
35-10-0110 Shelf, Adjustable, Alum 1/8" (EACH) $248.00 24-09-1100 Ventilation, Fixed Louvers, Body (EACH) $41.00 24-09-2100 Ventilation, 120V Elec, w/Timer, Cmpt (EACH) $385.00 35-30-2130 Slide Out Tray, ExtendoBed, 1500# (EACH) $2,557.00 35-20-1100 Slide Tray, 250#, Alum 3/16", <24"D (EACH) $481.00 35-25-1120 Slide Tray, BME 500#, Alum 3/16", <24"D (EACH) $536.00 35-50-1100 Tool Board, .250" Alum (EACH) $220.00 35-85-1100 Turtle Tile, Grating, Per Square Foot $31.00 35-85-2100 Dri-Dek, Grating, Per Square Foot $32.00

ELECTRICAL OPTIONS
40-15-3300 Battery Charger, Kussmaul, Autocharge 1000, #091-56-12 $929.00

15.A

40-15-3400 Battery Charger, Kussmaul, Autocharge 1200, #091-53-12 $1,690.00 40-15-3910 Battery Charger, Kussmaul, Bar Graph Display, #091-94-12 $220.00 40-15-5200 Shore Power Plug, Kussmaul Auto-Eject #091-18WP-120, 15 Amp $479.00 40-15-5300 Shore Power Plug, Kussmaul Auto-Eject #091-20WP-120, 20 Amp $505.00 40-15-5400 Shore Power Plug, Kussmaul Auto-Eject #091-159-30B-120, 30 A $741.00 40-20-1200 Load Manager, Class 1, TSM, #101540, Negative Output $990.00 40-20-1700 Low Voltage Alarm, Class 1, #100545, 12V, light/buzzer $557.00 41-44-3060 UPGRADE Compartment Lighting, Whelen, Fluorent Series $2,599.00 40-32-5050 Stop/Tail Light, Whelen #60R00FRR, LED, 4" x 6" (1) THIRD BRAKE LIGHT $358.00 41-15-1600 Map Light, Havis Shields #C-MAP-T-LED, 12" LED $179.00 41-21-2200 Spotlight, Cab, GO-LIGHT, 2020#, 12V $598.00 42-10-2000 Radio Antenna, Installation (EACH) $124.00 42-10-3600 Radio, Fire, Installation, Purchaser Supplied (EACH) $248.00 42-21-1100 12V Power Outlet, 20 Amp, Cab Dash (EACH) $69.00 42-21-1110 12V Power Outlet, 20 Amp, Console (EACH) $69.00 43-10-2100 Back Up Camera, Tear Drop W/Monitor $1,320.00 45-35-1200 Traffic Emitter, Opticom, Roof Mounted $2,392.00 46-05-1500 Traffic Advisor, Whelen, TAL65, 36", LED $859.00 46-05-1600 Traffic Advisor, Whelen, TA837L, 43", LED $893.00 46-05-5100 Traffic Arrow Light, 911EP, TD-WL36A $867.00

FRONT BUMPER OPTIONS
60-05-1600 Winch, Electric, Front Mount, 9,000#, Warn $2,592.00 60-05-1700 Winch, Electric, Front Mount, 12,000#, Warn $3,295.00 60-25-1500 Buckstop Bumper / Grill Guard, W/Winch Provisions $3,058.00 60-35-1300 Receiver, Front, Winch/Rope, 12,000# $784.00 $0.00
PAINT OPTIONS $0.00
80-01-1230 UPGRADE Paint, Cab/Chassis, 4 Door Commercial, Two Tone $6,050.00 80-01-3300 Paint, Chassis Wheels, Six (6), Job Color $1,238.00 81-20-2350 Striping Package, Custom Contact Factory

CHASSIS OPTIONS BY BOISE MOBILE EQUIPMENT
02-88-9500 Super Single Conversion, DRW to SRW $7,697.00 FS19DB12 OPTIONS

ELECTRICAL OPTIONS
40-15-3300 Battery Charger, Kussmaul, Autocharge 1000, #091-56-12 $929.00 40-15-3400 Battery Charger, Kussmaul, Autocharge 1200, #091-53-12 $1,690.00 40-15-3910 Battery Charger, Kussmaul, Bar Graph Display, #091-94-12 $220.00 40-15-5200 Shore Power Plug, Kussmaul Auto-Eject #091-18WP-120, 15 Amp $479.00 40-15-5300 Shore Power Plug, Kussmaul Auto-Eject #091-20WP-120, 20 Amp $505.00 40-15-5400 Shore Power Plug, Kussmaul Auto-Eject #091-159-30B-120, 30 A $741.00 40-20-1200 Load Manager, Class 1, TSM, #101540, Negative Output $990.00 40-20-1700 Low Voltage Alarm, Class 1, #100545, 12V, light/buzzer $557.00 41-44-3060 UPGRADE Compartment Lighting, Whelen, Fluorent Series $2,599.00 40-32-5050 Stop/Tail Light, Whelen #60R00FRR, LED, 4" x 6" (1) THIRD BRAKE LIGHT $358.00 41-15-1600 Map Light, Havis Shields #C-MAP-T-LED, 12" LED $179.00 41-21-2200 Spotlight, Cab, GO-LIGHT, 2020#, 12V $598.00 42-10-2000 Radio Antenna, Installation (EACH) $124.00 42-10-3600 Radio, Fire, Installation, Purchaser Supplied (EACH) $248.00 42-21-1100 12V Power Outlet, 20 Amp, Cab Dash (EACH) $69.00 42-21-1110 12V Power Outlet, 20 Amp, Console (EACH) $69.00 43-10-2100 Back Up Camera, Tear Drop W/Monitor $1,320.00 45-35-1200 Traffic Emitter, Opticom, Roof Mounted $2,392.00 46-05-1500 Traffic Advisor, Whelen, TAL65, 36", LED $859.00 46-05-1600 Traffic Advisor, Whelen, TA837L, 43", LED $893.00 46-05-5100 Traffic Arrow Light, 911EP, TD-WL36A $867.00

BODY / COMPARTMENT OPTIONS
35-10-0110 Shelf, Adjustable, Alum 1/8" (EACH) $248.00 24-09-1100 Ventilation, Fixed Louvers, Body (EACH) $41.00 24-09-2100 Ventilation, 120V Elec, w/Timer, Cmpt (EACH) $385.00 35-30-2130 Slide Out Tray, ExtendoBed, 1500# (EACH) $2,557.00 35-20-1100 Slide Tray, 250#, Alum 3/16", <24"D (EACH) $481.00 35-25-1120 Slide Tray, BME 500#, Alum 3/16", <24"D (EACH) $536.00 35-50-1100 Tool Board, .250" Alum (EACH) $220.00 35-85-1100 Turtle Tile, Grating, Per Square Foot $31.00 35-85-2100 Dri-Dek, Grating, Per Square Foot $32.00

PAINT OPTIONS
80-01-1230 UPGRADE Paint, Cab/Chassis, 4 Door Commercial, Two Tone $6,050.00 80-01-3300 Paint, Chassis Wheels, Six (6), Job Color $1,238.00 80-20-1700 Cmpt Pntg, Zolatone, Grey, (7)Cmpts $2,090.00 81-20-2350 Striping Package, Custom Contact Factory FS19DC01 / FS19DC02 OPTIONS

15.A

PLUMBING OPTIONS
07-07-1600 UPGRADE, WATEROUS, CSUC20, 1500GPM Pump $3,960.00 12-31-2100 Hose Reel, Hannay, Electric Rewind, Painted Steel $2,960.00 12-31-2200 Hose Reel, Hannay, Electric Rewind, Aluminum $3,703.00 12-40-3100 Monitor Discharge, 3", Over Midship Pump Enclosure $1,265.00 12-41-1100 Deck Gun, Elkhart, Stngr #1, LiftOff/Direct Trk Mount $4,534.00 12-43-1600 Deck Gun, TFT, KnightFire, XFC-63, Pkg $5,954.00 12-43-4100 Deck Gun, Telescoping Extension, TFT, XG12L $2,571.00 12-43-4200 Deck Gun, Telescoping Extension, TFT, XG18L $2,812.00 12-43-1100 Deck Gun, TFT, CrossFire, XFC-12, Pkg $5,149.00 12-43-1200 Deck Gun, TFT, CrossFire, XFC-32, Pkg $5,954.00 12-43-1300 Deck Gun, TFT, CrossFire, XFC-42, Pkg $5,679.00 12-43-1400 Deck Gun, TFT, CrossFire, XFC-52, Pkg $6,786.00 12-43-1500 Deck Gun, TFT, CrossFire, XFC-62, Pkg $8,429.00 13-10-1100 Foam System, FoamPro 1600 $6,380.00
13-10-1110 Foam System, FoamPro 1601 $6,449.00
13-10-1700 Foam System, FoamPro, 2002, 12V Elec, 2 Tanks $12,015.00 13-10-5200 Foam System, FoamPro, On-Off Switch in Cab $467.00 13-11-1100 Foam Upload System, BME $1,279.00 13-11-2000 Foam Pump, FoamPro, 12V Elec, (A) Refill Transfer $3,017.00 13-11-2100 Foam Pump, FoamPro, 12V Elec, (B) Refill Transfer $3,017.00 29-05-1100 Foam Tank Capacity, 10 Gallons, Class A, Poly $544.00 29-05-1200 Foam Tank Capacity, 20 Gallons, Class A, Poly $615.00 29-05-1210 Foam Tank Capacity, 25 Gallons, Class A, Poly $688.00 29-05-1300 Foam Tank Capacity, 30 Gallons, Class A, Poly $724.00 29-05-1310 Foam Tank Capacity, 40 Gallons, Class A, Poly $851.00 29-10-1100 Foam Tank Capacity, 10 Gallons, Class B, Poly $540.00 29-10-1200 Foam Tank Capacity, 20 Gallons, Class B, Poly $615.00 29-10-1300 Foam Tank Capacity, 30 Gallons, Class B, Poly $724.00 29-10-1400 Foam Tank Capacity, 50 Gallons, Class B, Poly $1,003.00 13-13-1050 Discharge, Class A, Discharge (PER OUTLET) $358.00 13-14-2060 Discharge, Class B, Discharge (PER OUTLET) $358.00 14-40-5100 Foam Tank Gauge, FRC, Class A, Pump Panel $651.00 14-40-5300 Foam Tank Gauge, FRC, Class A, Mini, Cab $474.00 14-40-5200 Foam Tank Gauge, FRC, Class B, Pump Panel $651.00 14-40-5400 Foam Tank Gauge, FRC, Class B, Mini, Cab $474.00 12-05-4100 Fog Nozzle, Elkhart, 3/4", Fixed (EACH) $1,078.00 14-26-1100 Heater, Pump Enc, 16,000BTU, Switch $660.00 14-26-1200 Heater, Pump Enc, 30,000BTU, Switch $1,004.00

ELECTRICAL OPTIONS
40-05-1250 UPGRADE Electrical, Multi-Plex, Weldon V-MUX $6,435.00 41-44-3060 UPGRADE Compartment Lighting, Whelen, Fluorent Series $2,599.00 40-32-5050 Stop/Tail Light, Whelen #60R00FRR, LED, 4" x 6" (1) THIRD BRAKE LIGHT $358.00 41-15-1600 Map Light, Havis Shields #C-MAP-T-LED, 12" LED $179.00 41-21-2200 Spotlight, Cab, GO-LIGHT, 2020#, 12V $598.00 42-10-2000 Radio Antenna, Installation (EACH) $124.00 42-10-3600 Radio, Fire, Installation, Purchaser Supplied (EACH) $248.00 42-21-1100 12V Power Outlet, 20 Amp, Cab Dash (EACH) $69.00 42-21-1110 12V Power Outlet, 20 Amp, Console (EACH) $69.00 43-10-2100 Back Up Camera, Tear Drop W/Monitor $1,320.00 44-15-1100 Siren, F-S, Q2B, Mechanical, Pedestal Mounted $2,691.00 44-15-1200 Siren, F-S, Q2B, Mechanical, Recess In Bumper, Center $2,861.00 44-15-1300 Siren, F-S, Q2B, Mechanical, Recess In Bumper, Left Side $2,861.00 44-15-1400 Siren, F-S, Q2B, Mechanical, Recess In Bumper, Right Side $2,861.00 44-20-1100 Siren Brake, F-S, Q2B, Driver $137.00 44-20-1200 Siren Brake, F-S, Q2B, Psngr $137.00 45-35-1200 Traffic Emitter, Opticom, Roof Mounted $2,392.00

BODY / COMPARTMENT OPTIONS
02-79-2100 Cab Step Compartment, With Steps, Under Cab, Rear Left Hand $2,887.00 02-79-2150 Cab Step Compartment, With Steps, Under Cab, Rear Right Hand $2,887.00 23-02-0002 High Side / High Side Body Option $8,910.00
24-09-1100 Ventilation, Fixed Louvers, Body (EACH) $41.00 24-09-2100 Ventilation, 120V Elec, w/Timer, Cmpt (Each) $385.00 24-20-5160 ExtendoBed, Rear Bumper and Step Platform, Steel, Slide Out $2,791.00 35-10-0110 Shelf, Adjustable, Alum 1/8" (EACH) $248.00 35-30-2130 Slide Out Tray, ExtendoBed, 1500# (EACH) $2,557.00 35-20-1100 Slide Tray, 250#, Alum 3/16", <24"D (EACH) $481.00 35-25-1120 Slide Tray, BME 500#, Alum 3/16", <24"D (EACH) $536.00 35-50-1100 Tool Board, .250" Alum (EACH) $220.00 35-85-1100 Turtle Tile, Grating, Per Square Foot $31.00

15.A

35-85-2100 Dri-Dek, Grating, Per Square Foot $32.00

PAINT OPTIONS
80-01-1230 UPGRADE Paint, Cab/Chassis, 4 Door Commercial, Two Tone $6,050.00 80-01-3300 Paint, Chassis Wheels, Six (6), Job Color $1,238.00 80-20-1700 Cmpt Pntg, Zolatone, Grey, (7)Cmpts $2,090.00 81-20-2350 Striping Package, Custom Contact Factory FS19DC03 / FS19DC04 OPTIONS

PLUMBING OPTIONS
07-07-1600 UPGRADE, WATEROUS, CSUC20, 1500GPM Pump $3,960.00 12-31-2100 Hose Reel, Hannay, Electric Rewind, Painted Steel $2,960.00 12-31-2200 Hose Reel, Hannay, Electric Rewind, Aluminum $3,703.00 12-40-3100 Monitor Discharge, 3", Over Midship Pump Enclosure $1,265.00 12-41-1100 Deck Gun, Elkhart, Stngr #1, LiftOff/Direct Trk Mount $4,534.00 12-43-1600 Deck Gun, TFT, KnightFire, XFC-63, Pkg $5,954.00 12-43-4100 Deck Gun, Telescoping Extension, TFT, XG12L $2,571.00 12-43-4200 Deck Gun, Telescoping Extension, TFT, XG18L $2,812.00 12-43-1100 Deck Gun, TFT, CrossFire, XFC-12, Pkg $5,149.00 12-43-1200 Deck Gun, TFT, CrossFire, XFC-32, Pkg $5,954.00 12-43-1300 Deck Gun, TFT, CrossFire, XFC-42, Pkg $5,679.00 12-43-1400 Deck Gun, TFT, CrossFire, XFC-52, Pkg $6,786.00 12-43-1500 Deck Gun, TFT, CrossFire, XFC-62, Pkg $8,429.00 13-10-1100 Foam System, FoamPro 1600 $6,380.00
13-10-1110 Foam System, FoamPro 1601 $6,449.00
13-10-1700 Foam System, FoamPro, 2002, 12V Elec, 2 Tanks $12,015.00 13-10-5200 Foam System, FoamPro, On-Off Switch in Cab $467.00 13-11-1100 Foam Upload System, BME $1,279.00 13-11-2000 Foam Pump, FoamPro, 12V Elec, (A) Refill Transfer $3,017.00 13-11-2100 Foam Pump, FoamPro, 12V Elec, (B) Refill Transfer $3,017.00 29-05-1100 Foam Tank Capacity, 10 Gallons, Class A, Poly $544.00 29-05-1200 Foam Tank Capacity, 20 Gallons, Class A, Poly $615.00 29-05-1210 Foam Tank Capacity, 25 Gallons, Class A, Poly $688.00 29-05-1300 Foam Tank Capacity, 30 Gallons, Class A, Poly $724.00 29-05-1310 Foam Tank Capacity, 40 Gallons, Class A, Poly $851.00 29-10-1100 Foam Tank Capacity, 10 Gallons, Class B, Poly $540.00 29-10-1200 Foam Tank Capacity, 20 Gallons, Class B, Poly $615.00 29-10-1300 Foam Tank Capacity, 30 Gallons, Class B, Poly $724.00 29-10-1400 Foam Tank Capacity, 50 Gallons, Class B, Poly $1,003.00 13-13-1050 Discharge, Class A, Discharge (PER OUTLET) $358.00 13-14-2060 Discharge, Class B, Discharge (PER OUTLET) $358.00 14-40-5100 Foam Tank Gauge, FRC, Class A, Pump Panel $651.00 14-40-5300 Foam Tank Gauge, FRC, Class A, Mini, Cab $474.00 14-40-5200 Foam Tank Gauge, FRC, Class B, Pump Panel $651.00 14-40-5400 Foam Tank Gauge, FRC, Class B, Mini, Cab $474.00 12-05-4100 Fog Nozzle, Elkhart, 3/4", Fixed (EACH) $1,078.00 14-26-1100 Heater, Pump Enc, 16,000BTU, Switch $660.00 14-26-1200 Heater, Pump Enc, 30,000BTU, Switch $1,004.00

ELECTRICAL OPTIONS
40-05-1250 UPGRADE Electrical, Multi-Plex, Weldon V-MUX $6,435.00 41-44-3060 UPGRADE Compartment Lighting, Whelen, Fluorent Series $2,599.00 40-32-5050 Stop/Tail Light, Whelen #60R00FRR, LED, 4" x 6" (1) THIRD BRAKE LIGHT $358.00 41-15-1600 Map Light, Havis Shields #C-MAP-T-LED, 12" LED $179.00 41-21-2200 Spotlight, Cab, GO-LIGHT, 2020#, 12V $598.00 42-10-2000 Radio Antenna, Installation (EACH) $124.00 42-10-3600 Radio, Fire, Installation, Purchaser Supplied (EACH) $248.00 42-21-1100 12V Power Outlet, 20 Amp, Cab Dash (EACH) $69.00 42-21-1110 12V Power Outlet, 20 Amp, Console (EACH) $69.00 43-10-2100 Back Up Camera, Tear Drop W/Monitor $1,320.00 44-15-1100 Siren, F-S, Q2B, Mechanical, Pedestal Mounted $2,691.00 44-15-1200 Siren, F-S, Q2B, Mechanical, Recess In Bumper, Center $2,861.00 44-15-1300 Siren, F-S, Q2B, Mechanical, Recess In Bumper, Left Side $2,861.00 44-15-1400 Siren, F-S, Q2B, Mechanical, Recess In Bumper, Right Side $2,861.00 44-20-1100 Siren Brake, F-S, Q2B, Driver $137.00 44-20-1200 Siren Brake, F-S, Q2B, Psngr $137.00 45-35-1200 Traffic Emitter, Opticom, Roof Mounted $2,392.00

BODY / COMPARTMENT OPTIONS
02-79-2150 Cab Step Compartment, With Steps, Under Cab, Rear Right Hand $2,887.00 14-10-4100 Compt Under Walkway, TM, LH T/P Door $880.00 14-10-4200 Compt Under Walkway, TM, RH T/P Door $880.00

15.A

35-10-0110 Shelf, Adjustable, Alum 1/8" (EACH) $248.00 23-02-0002 High Side / High Side Body Option $8,910.00
24-09-1100 Ventilation, Fixed Louvers, Body (EACH) $41.00 24-09-2100 Ventilation, 120V Elec, w/Timer, Cmpt (Each) $385.00 24-20-5160 ExtendoBed, Rear Bumper and Step Platform, Steel, Slide Out $2,791.00 35-30-2130 Slide Out Tray, ExtendoBed, 1500# (EACH) $2,557.00 35-20-1100 Slide Tray, 250#, Alum 3/16", <24"D (EACH) $481.00 35-25-1120 Slide Tray, BME 500#, Alum 3/16", <24"D (EACH) $536.00 35-50-1100 Tool Board, .250" Alum (EACH) $220.00 35-85-1100 Turtle Tile, Grating, Per Square Foot $31.00 35-85-2100 Dri-Dek, Grating, Per Square Foot $32.00

PAINT OPTIONS
80-01-1230 UPGRADE Paint, Cab/Chassis, 4 Door Commercial, Two Tone $6,050.00 80-01-3300 Paint, Chassis Wheels, Six (6), Job Color $1,238.00 80-20-1700 Cmpt Pntg, Zolatone, Grey, (7)Cmpts $2,090.00 81-20-2350 Striping Package, Custom Contact Factory FS19DC05 / FS19DC06 OPTIONS

PLUMBING OPTIONS
07-07-1600 UPGRADE, WATEROUS, CSUC20, 1500GPM Pump $3,960.00 11-06-4500 Intake, Ungated, 6", Frnt RH Bmpr $5,390.00 12-40-3100 Monitor Discharge, 3", Over Midship Pump Enclosure $1,265.00 12-41-1100 Deck Gun, Elkhart, Stngr #1, LiftOff/Direct Trk Mount $4,534.00 12-43-1600 Deck Gun, TFT, KnightFire, XFC-63, Pkg $5,954.00 12-43-4100 Deck Gun, Telescoping Extension, TFT, XG12L $2,571.00 12-43-4200 Deck Gun, Telescoping Extension, TFT, XG18L $2,812.00 12-43-1100 Deck Gun, TFT, CrossFire, XFC-12, Pkg $5,149.00 12-43-1200 Deck Gun, TFT, CrossFire, XFC-32, Pkg $5,954.00 12-43-1300 Deck Gun, TFT, CrossFire, XFC-42, Pkg $5,679.00 12-43-1400 Deck Gun, TFT, CrossFire, XFC-52, Pkg $6,786.00 12-43-1500 Deck Gun, TFT, CrossFire, XFC-62, Pkg $8,429.00 13-10-1100 Foam System, FoamPro 1600 $6,380.00
13-10-1110 Foam System, FoamPro 1601 $6,449.00
13-10-1700 Foam System, FoamPro, 2002, 12V Elec, 2 Tanks $12,015.00 13-10-5200 Foam System, FoamPro, On-Off Switch in Cab $467.00 13-11-1100 Foam Upload System, BME $1,279.00 13-11-2000 Foam Pump, FoamPro, 12V Elec, (A) Refill Transfer $3,017.00 13-11-2100 Foam Pump, FoamPro, 12V Elec, (B) Refill Transfer $3,017.00 29-05-1100 Foam Tank Capacity, 10 Gallons, Class A, Poly $544.00 29-05-1200 Foam Tank Capacity, 20 Gallons, Class A, Poly $615.00 29-05-1210 Foam Tank Capacity, 25 Gallons, Class A, Poly $688.00 29-05-1300 Foam Tank Capacity, 30 Gallons, Class A, Poly $724.00 29-05-1310 Foam Tank Capacity, 40 Gallons, Class A, Poly $851.00 29-10-1100 Foam Tank Capacity, 10 Gallons, Class B, Poly $540.00 29-10-1200 Foam Tank Capacity, 20 Gallons, Class B, Poly $615.00 29-10-1300 Foam Tank Capacity, 30 Gallons, Class B, Poly $724.00 29-10-1400 Foam Tank Capacity, 50 Gallons, Class B, Poly $1,003.00 13-13-1050 Discharge, Class A, Discharge (PER OUTLET) $358.00 13-14-2060 Discharge, Class B, Discharge (PER OUTLET) $358.00 14-40-5100 Foam Tank Gauge, FRC, Class A, Pump Panel $651.00 14-40-5300 Foam Tank Gauge, FRC, Class A, Mini, Cab $474.00 14-40-5200 Foam Tank Gauge, FRC, Class B, Pump Panel $651.00 14-40-5400 Foam Tank Gauge, FRC, Class B, Mini, Cab $474.00 12-05-4100 Fog Nozzle, Elkhart, 3/4", Fixed (EACH) $1,078.00 14-26-1100 Heater, Pump Enc, 16,000BTU, Switch $660.00 14-26-1200 Heater, Pump Enc, 30,000BTU, Switch $1,004.00

ELECTRICAL OPTIONS
40-05-1250 UPGRADE Electrical, Multi-Plex, Weldon V-MUX $6,435.00 41-44-3060 UPGRADE Compartment Lighting, Whelen, Fluorent Series $2,599.00 40-32-5050 Stop/Tail Light, Whelen #60R00FRR, LED, 4" x 6" (1) THIRD BRAKE LIGHT $358.00 41-15-1600 Map Light, Havis Shields #C-MAP-T-LED, 12" LED $179.00 41-21-2200 Spotlight, Cab, GO-LIGHT, 2020#, 12V $598.00 42-10-2000 Radio Antenna, Installation (EACH) $124.00 42-10-3600 Radio, Fire, Installation, Purchaser Supplied (EACH) $248.00 42-21-1100 12V Power Outlet, 20 Amp, Cab Dash (EACH) $69.00 42-21-1110 12V Power Outlet, 20 Amp, Console (EACH) $69.00 43-10-2100 Back Up Camera, Tear Drop W/Monitor $1,320.00 44-15-1100 Siren, F-S, Q2B, Mechanical, Pedestal Mounted $2,691.00 44-15-1200 Siren, F-S, Q2B, Mechanical, Recess In Bumper, Center $2,861.00 44-15-1300 Siren, F-S, Q2B, Mechanical, Recess In Bumper, Left Side $2,861.00 44-15-1400 Siren, F-S, Q2B, Mechanical, Recess In Bumper, Right Side $2,861.00

15.A

44-20-1100 Siren Brake, F-S, Q2B, Driver $137.00 44-20-1200 Siren Brake, F-S, Q2B, Psngr $137.00 45-35-1200 Traffic Emitter, Opticom, Roof Mounted $2,392.00

BODY / COMPARTMENT OPTIONS
14-10-4100 Compt Under Walkway, TM, LH T/P Door $880.00 14-10-4200 Compt Under Walkway, TM, RH T/P Door $880.00 23-02-0002 High Side / High Side Body Option $8,910.00
24-09-1100 Ventilation, Fixed Louvers, Body (EACH) $41.00 24-09-2100 Ventilation, 120V Elec, w/Timer, Cmpt (Each) $385.00 24-20-5160 ExtendoBed, Rear Bumper and Step Platform, Steel, Slide Out $2,791.00 35-10-0110 Shelf, Adjustable, Alum 1/8" (EACH) $248.00 35-30-2130 Slide Out Tray, ExtendoBed, 1500# (EACH) $2,557.00 35-20-1100 Slide Tray, 250#, Alum 3/16", <24"D (EACH) $481.00 35-25-1120 Slide Tray, BME 500#, Alum 3/16", <24"D (EACH) $536.00 35-50-1100 Tool Board, .250" Alum (EACH) $220.00 35-85-1100 Turtle Tile, Grating, Per Square Foot $31.00 35-85-2100 Dri-Dek, Grating, Per Square Foot $32.00

PAINT OPTIONS
80-01-1230 UPGRADE Paint, Cab/Chassis, 4 Door Commercial, Two Tone $6,050.00 80-01-3300 Paint, Chassis Wheels, Six (6), Job Color $1,238.00 80-20-1700 Cmpt Pntg, Zolatone, Grey, (7)Cmpts $2,090.00 81-20-2350 Striping Package, Custom Contact Factory FS19DD01 OPTIONS

BODY / COMPARTMENT OPTIONS
22-06-0012 UPGRADE RESCUE BODY TO 12FT $4,535.00 24-03-3200 UPGRADE Fenderettes, Body, Polished S/S, (2) 16"/19" rims $275.00 35-10-0110 Shelf, Adjustable, Alum 1/8" (EACH) $248.00 35-20-1100 Slide Tray, 250#, Alum 3/16", <24"D (EACH) $481.00 35-25-1120 Slide Tray, BME 500#, Alum 3/16", <24"D (EACH) $536.00 35-50-1100 Tool Board, .250" Alum (EACH) $220.00 35-85-1100 Turtle Tile, Grating, Per Square Foot $31.00 35-85-2100 Dri-Dek, Grating, Per Square Foot $32.00 24-05-1700 SCBA Stge, LH Fwd Whlwell, 8" Rnd, Cast Prod Door $309.00 24-05-2300 SCBA Stge, LH Rear Whlwell, 8" Rnd, Cast Prod Door $309.00 24-05-5700 SCBA Stge, RH Fwd Whlwell, 8" Rnd, Cast Prod Door $309.00 24-05-6300 SCBA Stge, RH Rear Whlwell, 8" Rnd, Cast Prod Door $309.00 24-09-1100 Ventilation, Fixed Louvers, Body (EACH) $41.00 24-09-2100 Ventilation, 120V Elec, w/Timer, Cmpt (1) Each $385.00 35-30-2280 ExtendoBed, "Scott Command" Carrier (Requires Option #35-30-2350 or 35-30-2370) $4,570.00 35-30-2290 ExtendoBed, "Colorado" Carrier (Requires Option #35-30-2350 or 35-30-2370) $1,563.00 35-30-2300 ExtendoBed, "Portville" Carrier (Requires Option #35-30-2350 or 35-30-2370) $3,323.00 35-30-2270 ExtendoBed, "Orange County" Carrier (Requires Option #35-30-2350 or 35-30-2370) $4,318.00 35-30-2280 ExtendoBed, "Scott Command" Carrier (Requires Option #35-30-2350 or 35-30-2370) $4,570.00 35-30-2290 ExtendoBed, "Colorado" Carrier (Requires Option #35-30-2350 or 35-30-2370) $1,563.00 35-30-2300 ExtendoBed, "Portville" Carrier (Requires Option #35-30-2350 or 35-30-2370) $3,323.00 35-30-2310 ExtendoBed, "Oklahoma" Carrier (Requires Option #35-30-2350 or 35-30-2370) $7,054.00 35-30-2320 ExtendoBed, "ATF" Carrier (Requires Option #35-30-2350 or 35-30-2370) $2,666.00 35-30-2330 ExtendoBed, "Federal" Carrier (Requires Option #35-30-2350 or 35-30-2370) $4,517.00 35-30-2340 ExtendoBed, "2 Stage Professional" Carrier $1,210.00 35-30-2350 ExtendoBed, "Professional" Carrier, (EBL-1072), #1000 Capacity $2,243.00 35-30-2360 ExtendoBed, "HD Slideout" Carrier $3,484.00 35-30-2370 ExtendoBed, EB-1575, #1500 Capacity, 110% Extension $2,553.00 35-30-2380 ExtendoBed, "West Carrol" Carrier (Requires Option #35-30-2350 or 35-30-2370) $1,435.00 35-30-2130 Slide Out Tray, ExtendoBed, 1500# (EACH) $2,557.00 35-30-2140 Slide Out Tray, ExtendoBed, Dual Direction, 1000# $3,657.00 24-10-2007 UPGRADE Door, Rollup, ROM. Painted $2,406.00 24-27-1300 Roof Access Ladder, Aluminum Tubing, RH Rear $1,292.00 24-27-1400 Roof Access Ladder, Aluminum Tubing, LH Rear $1,292.00 35-70-2100 SCBA Bottle Rack, Ziamatic Tube, (1) $207.00 35-70-2105 SCBA Bottle Rack, Ziamatic Tube, (2) $303.00 35-70-2110 SCBA Bottle Rack, Ziamatic Tube, (4) $608.00 35-75-1100 Backboard Mounting, (1) Vertical $358.00 35-75-1200 Backboard Mounting, (2) Vertical $536.00 35-75-1300 Backboard Mounting, (1) Horizontal $358.00 35-75-1400 Backboard Mounting, (2) Horizontal $536.00 35-75-2100 Stokes Basket Mounting, (1) Vertical $358.00 35-75-2200 Stokes Basket Mounting, (1) Horizontal $358.00 60-41-1100 Tie Off, Rope, Side of Body, High Side, (EACH) $536.00 60-41-1200 Tie Off, Rope, Side of Body, Low Side, (EACH) $536.00

15.A

ELECTRICAL OPTIONS
40-05-1250 UPGRADE Electrical, Multi-Plex, Weldon V-MUX $6,435.00 40-32-5050 Stop/Tail Light, Whelen #60R00FRR, LED, 4" x 6" (1) THIRD BRAKE LIGHT $358.00 41-36-3100 Scene Light, Whelen, LED, 4"x 6" (EACH) $394.00 41-36-5100 Scene Light, Whelen, LED, 7"x 9" (EACH) $547.00 41-36-5200 Scene Light, Whelen, PFP1, LED, (EACH) $1,416.00 41-44-3060 UPGRADE Compartment Lighting, Whelen, Fluorent Series $2,599.00 41-15-1600 Map Light, Havis Shields #C-MAP-T-LED, 12" LED $179.00 41-21-2200 Spotlight, Cab, GO-LIGHT, 2020#, 12V $598.00 42-10-2000 Radio Antenna, Installation (EACH) $124.00 42-10-3600 Radio, Fire, Installation, Purchaser Supplied (EACH) $248.00 42-21-1100 12V Power Outlet, 20 Amp, Cab Dash (EACH) $69.00 42-21-1110 12V Power Outlet, 20 Amp, Console (EACH) $69.00 43-10-2100 Back Up Camera, Tear Drop W/Monitor $1,320.00 45-35-1200 Traffic Emitter, Opticom, Roof Mounted $2,392.00 46-05-1500 Traffic Advisor, Whelen, TAL65, 36", LED $859.00 46-05-1600 Traffic Advisor, Whelen, TA837L, 43", LED $893.00 46-05-5100 Traffic Arrow Light, 911EP, TD-WL36A $867.00 54-10-1100 Light Tower, WB, 6' Hrzntl, 2-150W HID12V, FRC Opti, Remote $10,257.00 54-10-1500 Light Tower, WB, 7.5' Hrzntl, 2-150W HID12V, Rmt ctrl $10,565.00 50-05-1100 Generator, Honda Gas, 3.5KW, 120/240V, 1 Phase $2,377.00 50-05-1200 Generator, Honda Gas, 5KW, 120/240V, 1 Phase $3,208.00

FRONT BUMPER OPTIONS
60-05-1600 Winch, Electric, Front Mount, 9,000#, Warn $2,592.00 60-05-1700 Winch, Electric, Front Mount, 12,000#, Warn $3,295.00 60-25-1500 Buckstop Bumper / Grill Guard, W/Winch Provisions $3,058.00 60-35-1300 Receiver, Front, Winch/Rope, 12,000# $784.00

REAR BUMPER OPTIONS
60-35-2200 Receiver, Rear, Winch/Rope/Trailer, 12,000# $1,086.00 60-40-2000 Trailer Hitch Power Plug, 12 Volt, 4 Prong $337.00 60-40-2200 Trailer Hitch Power Plug, 12 Volt, 7 Prong $337.00

PAINT OPTIONS
80-01-1230 UPGRADE Paint, Cab/Chassis, 4 Door Commercial, Two Tone $6,050.00 80-01-3300 Paint, Chassis Wheels, Six (6), Job Color $1,238.00 80-20-1700 Cmpt Pntg, Zolatone, Grey, (7)Cmpts $2,090.00 81-20-2350 Striping Package, Custom Contact Factory FS19DD02 / FS19DD03 OPTIONS

BODY / COMPARTMENT OPTIONS
24-03-4100 Fenderettes, Body, Polished S/S, 22.5" rims (2) Single Axle $598.00 35-10-0110 Shelf, Adjustable, Alum 1/8" (EACH) $248.00 35-20-1100 Slide Tray, 250#, Alum 3/16", <24"D (EACH) $481.00 35-25-1120 Slide Tray, BME 500#, Alum 3/16", <24"D (EACH) $536.00 35-30-2130 Slide Out Tray, ExtendoBed, 1500# (EACH) $2,557.00 35-30-2140 Slide Out Tray, ExtendoBed, Dual Direction, 1000# $3,657.00 35-50-1100 Tool Board, .250" Alum (EACH) $220.00 35-85-1100 Turtle Tile, Grating, Per Square Foot $31.00 35-85-2100 Dri-Dek, Grating, Per Square Foot $32.00 24-05-1700 SCBA Stge, LH Fwd Whlwell, 8" Rnd, Cast Prod Door $309.00 24-05-2300 SCBA Stge, LH Rear Whlwell, 8" Rnd, Cast Prod Door $309.00 24-05-5700 SCBA Stge, RH Fwd Whlwell, 8" Rnd, Cast Prod Door $309.00 24-05-6300 SCBA Stge, RH Rear Whlwell, 8" Rnd, Cast Prod Door $309.00 24-09-1100 Ventilation, Fixed Louvers, Body (EACH) $41.00 24-09-2100 Ventilation, 120V Elec, w/Timer, Cmpt (1) Each $385.00 24-10-2007 UPGRADE Door, Rollup, ROM. Painted $2,406.00 24-20-5160 ExtendoBed, Rear Bumper and Step Platform, Steel, Slide Out $2,791.00 24-27-1300 Roof Access Ladder, Aluminum Tubing, RH Rear $1,292.00 24-27-1400 Roof Access Ladder, Aluminum Tubing, LH Rear $1,292.00 35-30-2280 ExtendoBed, "Scott Command" Carrier (Requires Option #35-30-2350 or 35-30-2370) $4,570.00 35-30-2290 ExtendoBed, "Colorado" Carrier (Requires Option #35-30-2350 or 35-30-2370) $1,563.00 35-30-2300 ExtendoBed, "Portville" Carrier (Requires Option #35-30-2350 or 35-30-2370) $3,323.00 35-30-2270 ExtendoBed, "Orange County" Carrier (Requires Option #35-30-2350 or 35-30-2370) $4,318.00 35-30-2280 ExtendoBed, "Scott Command" Carrier (Requires Option #35-30-2350 or 35-30-2370) $4,570.00 35-30-2290 ExtendoBed, "Colorado" Carrier (Requires Option #35-30-2350 or 35-30-2370) $1,563.00 35-30-2300 ExtendoBed, "Portville" Carrier (Requires Option #35-30-2350 or 35-30-2370) $3,323.00 35-30-2310 ExtendoBed, "Oklahoma" Carrier (Requires Option #35-30-2350 or 35-30-2370) $7,054.00 35-30-2320 ExtendoBed, "ATF" Carrier (Requires Option #35-30-2350 or 35-30-2370) $2,666.00 35-30-2330 ExtendoBed, "Federal" Carrier (Requires Option #35-30-2350 or 35-30-2370) $4,517.00 35-30-2340 ExtendoBed, "2 Stage Professional" Carrier $1,210.00 35-30-2350 ExtendoBed, "Professional" Carrier, (EBL-1072), #1000 Capacity $2,243.00 35-30-2360 ExtendoBed, "HD Slideout" Carrier $3,484.00 35-30-2370 ExtendoBed, EB-1575, #1500 Capacity, 110% Extension $2,553.00

15.A

35-30-2380 ExtendoBed, "West Carrol" Carrier (Requires Option #35-30-2350 or 35-30-2370) $1,435.00 35-70-2100 SCBA Bottle Rack, Ziamatic Tube, (1) $207.00 35-70-2105 SCBA Bottle Rack, Ziamatic Tube, (2) $303.00 35-70-2110 SCBA Bottle Rack, Ziamatic Tube, (4) $608.00 35-75-1100 Backboard Mounting, (1) Vertical $358.00 35-75-1200 Backboard Mounting, (2) Vertical $536.00 35-75-1300 Backboard Mounting, (1) Horizontal $358.00 35-75-1400 Backboard Mounting, (2) Horizontal $536.00 35-75-2100 Stokes Basket Mounting, (1) Vertical $358.00 35-75-2200 Stokes Basket Mounting, (1) Horizontal $358.00 35-90-1400 Awning, Rollout, Manual, Up to 20' $3,135.00 60-41-1100 Tie Off, Rope, Side of Body, High Side, (EACH) $536.00 60-41-1200 Tie Off, Rope, Side of Body, Low Side, (EACH) $536.00

ELECTRICAL OPTIONS
40-05-1250 UPGRADE Electrical, Multi-Plex, Weldon V-MUX $6,435.00 40-32-5050 Stop/Tail Light, Whelen #60R00FRR, LED, 4" x 6" (1) THIRD BRAKE LIGHT $358.00 41-36-3100 Scene Light, Whelen, LED, 4"x 6" (EACH) $394.00 41-36-5100 Scene Light, Whelen, LED, 7"x 9" (EACH) $547.00 41-36-5200 Scene Light, Whelen, PFP1, LED, (EACH) $1,416.00 41-44-3060 UPGRADE Compartment Lighting, Whelen, Fluorent Series $2,599.00 41-15-1600 Map Light, Havis Shields #C-MAP-T-LED, 12" LED $179.00 41-21-2200 Spotlight, Cab, GO-LIGHT, 2020#, 12V $598.00 42-10-2000 Radio Antenna, Installation (EACH) $124.00 42-10-3600 Radio, Fire, Installation, Purchaser Supplied (EACH) $248.00 42-21-1100 12V Power Outlet, 20 Amp, Cab Dash (EACH) $69.00 42-21-1110 12V Power Outlet, 20 Amp, Console (EACH) $69.00 43-10-2100 Back Up Camera, Tear Drop W/Monitor $1,320.00 44-15-1100 Siren, F-S, Q2B, Mechanical, Pedestal Mounted $2,691.00 44-15-1200 Siren, F-S, Q2B, Mechanical, Recess In Bumper, Center $2,861.00 44-15-1300 Siren, F-S, Q2B, Mechanical, Recess In Bumper, Left Side $2,861.00 44-15-1400 Siren, F-S, Q2B, Mechanical, Recess In Bumper, Right Side $2,861.00 44-20-1100 Siren Brake, F-S, Q2B, Driver $137.00 44-20-1200 Siren Brake, F-S, Q2B, Psngr $137.00 45-35-1200 Traffic Emitter, Opticom, Roof Mounted $2,392.00 46-05-1500 Traffic Advisor, Whelen, TAL65, 36", LED $859.00 46-05-1600 Traffic Advisor, Whelen, TA837L, 43", LED $893.00 46-05-5100 Traffic Arrow Light, 911EP, TD-WL36A $867.00 50-05-1100 Generator, Honda Gas, 3.5KW, 120/240V, 1 Phase $2,377.00 50-05-1200 Generator, Honda Gas, 5KW, 120/240V, 1 Phase $3,208.00 50-27-2450 Generator, Harrison Hyd, 10KW, MCR, 120/240V, 1 Phase $24,962.00 50-27-2500 Generator, Harrison Hyd, 15KW, 120/240V, 1 Phase $28,448.00 50-27-2600 Generator, Harrison Hyd, 20KW, 120/240V, 1 Phase $30,875.00 50-27-3100 Generator, Smart Power Hyd, 6KW, 120/240V, 1 Phase $15,095.00 50-27-3200 Generator, Smart Power Hyd, 8KW, 120/240V, 1 Phase $16,360.00 50-27-3300 Generator, Smart Power Hyd, 10KW, 120/240V, 1 Phase $19,755.00 51-10-1210 Receptacle, 120V, 20 Amp, Straight Blade (EACH) $220.00 51-15-1100 Receptacle, 240V, 20 Amp, L6-20, Twist Lock (EACH) $220.00 52-25-1100 LED Scenelight, SPECTRA, 240VAC 20km lm, Lamphead (EA) $2,031.00 52-25-1110 LED Scenelight, SPECTRA, 120VAC 20km lm, Lamphead (EA) $1,893.00 52-25-1120 LED Scenelight, SPECTRA, DC 15km lm, Lamphead (EA) $1,256.00 52-25-1130 LED Scenelight, SPECTRA, DC 20km lm, Lamphead (EA) $1,470.00 53-05-1110 Cable Reel, Hannay, Elec Rewind, 120V, 3 Wire, 50 Amp (EACH) $2,689.00 53-30-2100 Junction Box, Akron/GFE, 4-120V L5-20 Receptacles $660.00 53-30-3000 Junction Box, Holder, Brushed Aluminum $289.00 55-05-1050 Light Tower, CL, CL602A-LED, 6-150W $31,680.00 61-02-1400 Breathing Air Comp, Bauer, 25CFM, 20HP, 240 Volt-3 Phase (BD02 thru BD06 ONLY) $108,916.00 61-09-1220 Breathing Air Reel, High Pres, Red (6000#), 200'x1/4" hose (EACH) $3,301.00 62-01-1130 HRT Reel, Hannay, Elec Rewind (1), W/ 100' Hose $3,877.00 62-01-1140 HRT Reel, Hannay, Elec Rewind (1), W/ 200' Hose $4,840.00 62-06-4100 HRT Power Unit, Hurst, Electric Duo-Pump $6,462.00

FRONT BUMPER OPTIONS
60-05-1700 Winch, Electric, Front Mount, 12,000#, Warn $3,295.00 60-35-1300 Receiver, Front, Winch/Rope, 12,000# $784.00

REAR BUMPER OPTIONS
60-35-2200 Receiver, Rear, Winch/Rope/Trailer, 12,000# $1,086.00 60-40-2000 Trailer Hitch Power Plug, 12 Volt, 4 Prong $337.00 60-40-2200 Trailer Hitch Power Plug, 12 Volt, 7 Prong $337.00

PAINT OPTIONS
80-01-1200 Paint, Cab/Chassis, 2 Door Commercial, Two Tone $6,050.00 80-01-3300 Paint, Chassis Wheels, Six (6), Job Color $1,238.00 80-20-1700 Cmpt Pntg, Zolatone, Grey $2,090.00 81-20-2350 Striping Package, Custom Contact Factory

CHASSIS OPTIONS BY BOISE MOBILE EQUIPMENT

15.A

02-73-2100 Bumper Cmpt, Left, Tool Compartment $564.00 02-73-2200 Bumper Cmpt, Left, Reel Compartment $564.00 02-73-3105 Bumper Cmpt, Center, Tool Compartment $564.00 02-73-3200 Bumper Cmpt, Center, Reel Compartment $399.00 02-73-4100 Bumper Cmpt, Right, Tool Compartment $399.00 02-73-4200 Bumper Cmpt, Right, Reel Compartment $399.00 02-73-5100 Bumper Cmpt, Cover, Vinyl/Hypalon (1) $220.00 02-73-5200 Bumper Cmpt, Covers, Vinyl/Hypalon (2) $440.00 02-73-5300 Bumper Cmpt, Covers, Vinyl/Hypalon (3) $660.00 02-73-6100 Bumper Cmpt, Door, Alum T/P (1) $502.00 02-73-6200 Bumper Cmpt, Doors, Alum T/P (2) $426.00 02-73-6300 Bumper Cmpt, Doors, Alum T/P (3) $1,506.00 02-73-6400 Bumper Cmpt, Door, Alum T/P (1) Full Width $1,430.00 02-73-6500 Bumper Cmpt, Velcro Straps, (2) per Cmpt $165.00 02-73-7100 Bumper Cmpt Light, Auto, w/Door Open Indicator Dash $302.00 02-73-8100 Bumper Guide Poles, Lighted $385.00 02-74-1600 Air Horns, Buell, (2) Hood Mounted $887.00 02-74-2100 Air Horn, Control, Driver, Elec horn or Air horns switch $139.00 02-74-2110 Air Horn, Control, Driver, Siren/air horn, switch $139.00 02-74-2200 Air Horn, Control, Driver, Single Foot Switch $145.00 02-74-2400 Air Horn, Control, Psngr, Single Foot Switch $145.00 02-74-2500 Air Horn, Control, Psngr, Single Dash Switch $139.00 02-74-2510 Air Horn, Control, Psngr, Console $137.00 02-74-2520 Air Horn, Control, Pump Panel $267.00 02-75-2100 Wheel Covers, S/S Liner/Covers, 22.5", Single Axle $907.00 02-76-1300 Exhaust Heat Shield, Under Body Compartments $323.00 02-76-1400 Exhaust, Vertical, Modification $83.00 02-76-1500 Exhaust, Horizontal, Special, Modification $811.00 02-78-1100 Tire Chains, Automatic, On-Spot, per axle, w/mntg brkt $2,454.00 02-79-1200 Cab Step, Fuel Tank Cover, Alum T/P, LH $1,073.00 02-87-1200 Air Brake Compressor, Kussmaul, 12V, 091-9, (100PSI) $846.00 02-87-1400 Air Inlet Plug, Kussmaul, Auto-Eject, LH cab step $708.00 02-88-7100 Protective Sleeve, Air, Fuel, Elec Lines, Fire Resistant Sleeves $715.00 FS19DE01 / FS19DE02 OPTIONS

PLUMBING OPTIONS
12-40-3100 Monitor Discharge, 3", Over Midship Pump Enclosure $1,265.00 12-41-1100 Deck Gun, Elkhart, Stngr #1, LiftOff/Direct Trk Mount $4,534.00 12-43-1600 Deck Gun, TFT, KnightFire, XFC-63, Pkg $5,954.00 12-43-4100 Deck Gun, Telescoping Extension, TFT, XG12L $2,571.00 12-43-4200 Deck Gun, Telescoping Extension, TFT, XG18L $2,812.00 12-43-1100 Deck Gun, TFT, CrossFire, XFC-12, Pkg $5,149.00 12-43-1200 Deck Gun, TFT, CrossFire, XFC-32, Pkg $5,954.00 12-43-1300 Deck Gun, TFT, CrossFire, XFC-42, Pkg $5,679.00 12-43-1400 Deck Gun, TFT, CrossFire, XFC-52, Pkg $6,786.00 12-43-1500 Deck Gun, TFT, CrossFire, XFC-62, Pkg $8,429.00 13-10-1100 Foam System, FoamPro 1600 $6,380.00
13-10-1110 Foam System, FoamPro 1601 $6,449.00
13-10-1700 Foam System, FoamPro, 2002, 12V Elec, 2 Tanks $12,015.00 13-10-5200 Foam System, FoamPro, On-Off Switch in Cab $467.00 13-11-1100 Foam Upload System, BME $1,279.00 13-11-2000 Foam Pump, FoamPro, 12V Elec, (A) Refill Transfer $3,017.00 13-11-2100 Foam Pump, FoamPro, 12V Elec, (B) Refill Transfer $3,017.00 29-05-1100 Foam Tank Capacity, 10 Gallons, Class A, Poly $544.00 29-05-1200 Foam Tank Capacity, 20 Gallons, Class A, Poly $615.00 29-05-1210 Foam Tank Capacity, 25 Gallons, Class A, Poly $688.00 29-05-1300 Foam Tank Capacity, 30 Gallons, Class A, Poly $724.00 29-05-1310 Foam Tank Capacity, 40 Gallons, Class A, Poly $851.00 29-10-1100 Foam Tank Capacity, 10 Gallons, Class B, Poly $540.00 29-10-1200 Foam Tank Capacity, 20 Gallons, Class B, Poly $615.00 29-10-1300 Foam Tank Capacity, 30 Gallons, Class B, Poly $724.00 29-10-1400 Foam Tank Capacity, 50 Gallons, Class B, Poly $1,003.00 13-13-1050 Discharge, Class A, Discharge (PER OUTLET) $358.00 13-14-2060 Discharge, Class B, Discharge (PER OUTLET) $358.00 14-40-5100 Foam Tank Gauge, FRC, Class A, Pump Panel $651.00 14-40-5300 Foam Tank Gauge, FRC, Class A, Mini, Cab $474.00 14-40-5200 Foam Tank Gauge, FRC, Class B, Pump Panel $651.00 14-40-5400 Foam Tank Gauge, FRC, Class B, Mini, Cab $474.00 12-05-4100 Fog Nozzle, Elkhart, 3/4", Fixed (EACH) $1,078.00 14-26-1100 Heater, Pump Enc, 16,000BTU, Switch $660.00 14-26-1200 Heater, Pump Enc, 30,000BTU, Switch $1,004.00

ELECTRICAL OPTIONS
40-05-1250 UPGRADE Electrical, Multi-Plex, Weldon V-MUX $6,435.00

15.A

41-36-3100 Scene Light, Whelen, LED, 4"x 6" (EACH) $394.00 41-36-5100 Scene Light, Whelen, LED, 7"x 9" (EACH) $547.00 41-36-5200 Scene Light, Whelen, PFP1, LED, (EACH) $1,416.00 41-44-3060 UPGRADE Compartment Lighting, Whelen, Fluorent Series $2,599.00 40-32-5050 Stop/Tail Light, Whelen #60R00FRR, LED, 4" x 6" (1) THIRD BRAKE LIGHT $358.00 41-15-1600 Map Light, Havis Shields #C-MAP-T-LED, 12" LED $179.00 41-21-2200 Spotlight, Cab, GO-LIGHT, 2020#, 12V $598.00 42-10-2000 Radio Antenna, Installation (EACH) $124.00 42-10-3600 Radio, Fire, Installation, Purchaser Supplied (EACH) $248.00 42-21-1100 12V Power Outlet, 20 Amp, Cab Dash (EACH) $69.00 42-21-1110 12V Power Outlet, 20 Amp, Console (EACH) $69.00 44-15-1100 Siren, F-S, Q2B, Mechanical, Pedestal Mounted $2,691.00 44-15-1200 Siren, F-S, Q2B, Mechanical, Recess In Bumper, Center $2,861.00 44-15-1300 Siren, F-S, Q2B, Mechanical, Recess In Bumper, Left Side $2,861.00 44-15-1400 Siren, F-S, Q2B, Mechanical, Recess In Bumper, Right Side $2,861.00 44-20-1100 Siren Brake, F-S, Q2B, Driver $137.00 44-20-1200 Siren Brake, F-S, Q2B, Psngr $137.00 45-35-1200 Traffic Emitter, Opticom, Roof Mounted $2,392.00 46-05-1500 Traffic Advisor, Whelen, TAL65, 36", LED $859.00 46-05-1600 Traffic Advisor, Whelen, TA837L, 43", LED $893.00 46-05-5100 Traffic Arrow Light, 911EP, TD-WL36A $867.00 43-10-2100 Back Up Camera, Tear Drop W/Monitor $1,320.00

BODY / COMPARTMENT OPTIONS
24-03-4100 Fenderettes, Body, Polished S/S, 22.5" rims (2) Single Axle $598.00 24-20-5160 ExtendoBed, Rear Bumper and Step Platform, Steel, Slide Out $2,791.00 35-10-0110 Shelf, Adjustable, Alum 1/8" (EACH) $248.00 35-20-1100 Slide Tray, 250#, Alum 3/16", <24"D (EACH) $481.00 35-25-1120 Slide Tray, BME 500#, Alum 3/16", <24"D (EACH) $536.00 35-30-2130 Slide Out Tray, ExtendoBed, 1500# (EACH) $2,557.00 35-30-2140 Slide Out Tray, ExtendoBed, Dual Direction, 1000# $3,657.00 35-50-1100 Tool Board, .250" Alum (EACH) $220.00 35-85-1100 Turtle Tile, Grating, Per Square Foot $31.00 35-85-2100 Dri-Dek, Grating, Per Square Foot $32.00 24-05-1700 SCBA Stge, LH Fwd Whlwell, 8" Rnd, Cast Prod Door $309.00 24-05-2300 SCBA Stge, LH Rear Whlwell, 8" Rnd, Cast Prod Door $309.00 24-05-5700 SCBA Stge, RH Fwd Whlwell, 8" Rnd, Cast Prod Door $309.00 24-05-6300 SCBA Stge, RH Rear Whlwell, 8" Rnd, Cast Prod Door $309.00 24-09-1100 Ventilation, Fixed Louvers, Body (EACH) $41.00 24-09-2100 Ventilation, 120V Elec, w/Timer, Cmpt (1) Each $385.00 90-08-1300 Folding Water Tank, Fold-A-Tank,2100 Gallon, Alum Frm,22oz $1,348.00 90-08-3700 Folding Tank Mounting, Zico 12V Elec, Right Side $4,937.00 90-08-4100 Folding Tank Cover, Smooth Aluminum, Painted Job Color $866.00 90-08-4200 Folding Tank Cover, Aluminum Diamond Plate $600.00

CHASSIS OPTIONS BY BOISE MOBILE EQUIPMENT
02-73-2100 Bumper Cmpt, Left, Tool Compartment $564.00 02-73-2200 Bumper Cmpt, Left, Reel Compartment $564.00 02-73-3105 Bumper Cmpt, Center, Tool Compartment $564.00 02-73-3200 Bumper Cmpt, Center, Reel Compartment $399.00 02-73-4100 Bumper Cmpt, Right, Tool Compartment $399.00 02-73-4200 Bumper Cmpt, Right, Reel Compartment $399.00 02-73-5100 Bumper Cmpt, Cover, Vinyl/Hypalon (1) $220.00 02-73-5200 Bumper Cmpt, Covers, Vinyl/Hypalon (2) $440.00 02-73-5300 Bumper Cmpt, Covers, Vinyl/Hypalon (3) $660.00 02-73-6100 Bumper Cmpt, Door, Alum T/P (1) $502.00 02-73-6200 Bumper Cmpt, Doors, Alum T/P (2) $426.00 02-73-6300 Bumper Cmpt, Doors, Alum T/P (3) $1,506.00 02-73-6400 Bumper Cmpt, Door, Alum T/P (1) Full Width $1,430.00 02-73-6500 Bumper Cmpt, Velcro Straps, (2) per Cmpt $165.00 02-73-7100 Bumper Cmpt Light, Auto, w/Door Open Indicator Dash $302.00 02-73-8100 Bumper Guide Poles, Lighted $385.00 02-74-1600 Air Horns, Buell, (2) Hood Mounted $887.00 02-74-2100 Air Horn, Control, Driver, Elec horn or Air horns switch $139.00 02-74-2110 Air Horn, Control, Driver, Siren/air horn, switch $139.00 02-74-2200 Air Horn, Control, Driver, Single Foot Switch $145.00 02-74-2400 Air Horn, Control, Psngr, Single Foot Switch $145.00 02-74-2500 Air Horn, Control, Psngr, Single Dash Switch $139.00 02-74-2510 Air Horn, Control, Psngr, Console $137.00 02-74-2520 Air Horn, Control, Pump Panel $267.00 02-75-2100 Wheel Covers, S/S Liner/Covers, 22.5", Single Axle $907.00 02-76-1300 Exhaust Heat Shield, Under Body Compartments $323.00 02-76-1400 Exhaust, Vertical, Modification $83.00 02-76-1500 Exhaust, Horizontal, Special, Modification $811.00 02-78-1100 Tire Chains, Automatic, On-Spot, per axle, w/mntg brkt $2,454.00 02-79-1200 Cab Step, Fuel Tank Cover, Alum T/P, LH $1,073.00 02-87-1200 Air Brake Compressor, Kussmaul, 12V, 091-9, (100PSI) $846.00

15.A

02-87-1400 Air Inlet Plug, Kussmaul, Auto-Eject, LH cab step $708.00 02-88-7100 Protective Sleeve, Air, Fuel, Elec Lines, Fire Resistant Sleeves $715.00

PAINT OPTIONS
80-01-1200 Paint, Cab/Chassis, 2 Door Commercial, Two Tone $6,050.00 80-01-3300 Paint, Chassis Wheels, Six (6), Job Color $1,238.00 80-20-1700 Cmpt Pntg, Zolatone, Grey $2,090.00 81-20-2350 Striping Package, Custom Contact Factory FS19DE03 / FS19DE04 OPTIONS

PLUMBING OPTIONS
12-40-3100 Monitor Discharge, 3", Over Midship Pump Enclosure $1,265.00 12-41-1100 Deck Gun, Elkhart, Stngr #1, LiftOff/Direct Trk Mount $4,534.00 12-43-1600 Deck Gun, TFT, KnightFire, XFC-63, Pkg $5,954.00 12-43-4100 Deck Gun, Telescoping Extension, TFT, XG12L $2,571.00 12-43-4200 Deck Gun, Telescoping Extension, TFT, XG18L $2,812.00 12-43-1100 Deck Gun, TFT, CrossFire, XFC-12, Pkg $5,149.00 12-43-1200 Deck Gun, TFT, CrossFire, XFC-32, Pkg $5,954.00 12-43-1300 Deck Gun, TFT, CrossFire, XFC-42, Pkg $5,679.00 12-43-1400 Deck Gun, TFT, CrossFire, XFC-52, Pkg $6,786.00 12-43-1500 Deck Gun, TFT, CrossFire, XFC-62, Pkg $8,429.00 13-10-1100 Foam System, FoamPro 1600 $6,380.00
13-10-1110 Foam System, FoamPro 1601 $6,449.00
13-10-1700 Foam System, FoamPro, 2002, 12V Elec, 2 Tanks $12,015.00 13-10-5200 Foam System, FoamPro, On-Off Switch in Cab $467.00 13-11-1100 Foam Upload System, BME $1,279.00 13-11-2000 Foam Pump, FoamPro, 12V Elec, (A) Refill Transfer $3,017.00 13-11-2100 Foam Pump, FoamPro, 12V Elec, (B) Refill Transfer $3,017.00 29-05-1100 Foam Tank Capacity, 10 Gallons, Class A, Poly $544.00 29-05-1200 Foam Tank Capacity, 20 Gallons, Class A, Poly $615.00 29-05-1210 Foam Tank Capacity, 25 Gallons, Class A, Poly $688.00 29-05-1300 Foam Tank Capacity, 30 Gallons, Class A, Poly $724.00 29-05-1310 Foam Tank Capacity, 40 Gallons, Class A, Poly $851.00 29-10-1100 Foam Tank Capacity, 10 Gallons, Class B, Poly $540.00 29-10-1200 Foam Tank Capacity, 20 Gallons, Class B, Poly $615.00 29-10-1300 Foam Tank Capacity, 30 Gallons, Class B, Poly $724.00 29-10-1400 Foam Tank Capacity, 50 Gallons, Class B, Poly $1,003.00 13-13-1050 Discharge, Class A, Discharge (PER OUTLET) $358.00 13-14-2060 Discharge, Class B, Discharge (PER OUTLET) $358.00 14-40-5100 Foam Tank Gauge, FRC, Class A, Pump Panel $651.00 14-40-5300 Foam Tank Gauge, FRC, Class A, Mini, Cab $474.00 14-40-5200 Foam Tank Gauge, FRC, Class B, Pump Panel $651.00 14-40-5400 Foam Tank Gauge, FRC, Class B, Mini, Cab $474.00 12-05-4100 Fog Nozzle, Elkhart, 3/4", Fixed (EACH) $1,078.00 14-26-1100 Heater, Pump Enc, 16,000BTU, Switch $660.00 14-26-1200 Heater, Pump Enc, 30,000BTU, Switch $1,004.00

ELECTRICAL OPTIONS
40-05-1250 UPGRADE Electrical, Multi-Plex, Weldon V-MUX $6,435.00 41-36-3100 Scene Light, Whelen, LED, 4"x 6" (EACH) $394.00 41-36-5100 Scene Light, Whelen, LED, 7"x 9" (EACH) $547.00 41-36-5200 Scene Light, Whelen, PFP1, LED, (EACH) $1,416.00 41-44-3060 UPGRADE Compartment Lighting, Whelen, Fluorent Series $2,599.00 40-32-5050 Stop/Tail Light, Whelen #60R00FRR, LED, 4" x 6" (1) THIRD BRAKE LIGHT $358.00 41-15-1600 Map Light, Havis Shields #C-MAP-T-LED, 12" LED $179.00 41-21-2200 Spotlight, Cab, GO-LIGHT, 2020#, 12V $598.00 42-10-2000 Radio Antenna, Installation (EACH) $124.00 42-10-3600 Radio, Fire, Installation, Purchaser Supplied (EACH) $248.00 42-21-1100 12V Power Outlet, 20 Amp, Cab Dash (EACH) $69.00 42-21-1110 12V Power Outlet, 20 Amp, Console (EACH) $69.00 43-10-2100 Back Up Camera, Tear Drop W/Monitor $1,320.00 44-15-1100 Siren, F-S, Q2B, Mechanical, Pedestal Mounted $2,691.00 44-15-1200 Siren, F-S, Q2B, Mechanical, Recess In Bumper, Center $2,861.00 44-15-1300 Siren, F-S, Q2B, Mechanical, Recess In Bumper, Left Side $2,861.00 44-15-1400 Siren, F-S, Q2B, Mechanical, Recess In Bumper, Right Side $2,861.00 44-20-1100 Siren Brake, F-S, Q2B, Driver $137.00 44-20-1200 Siren Brake, F-S, Q2B, Psngr $137.00 45-35-1200 Traffic Emitter, Opticom, Roof Mounted $2,392.00 46-05-1500 Traffic Advisor, Whelen, TAL65, 36", LED $859.00 46-05-1600 Traffic Advisor, Whelen, TA837L, 43", LED $893.00 46-05-5100 Traffic Arrow Light, 911EP, TD-WL36A $867.00

BODY / COMPARTMENT OPTIONS
24-03-4100 Fenderettes, Body, Polished S/S, 22.5" rims (2) Single Axle $598.00

15.A

24-20-5160 ExtendoBed, Rear Bumper and Step Platform, Steel, Slide Out $2,791.00 35-10-0110 Shelf, Adjustable, Alum 1/8" (EACH) $248.00 35-20-1100 Slide Tray, 250#, Alum 3/16", <24"D (EACH) $481.00 35-25-1120 Slide Tray, BME 500#, Alum 3/16", <24"D (EACH) $536.00 35-30-2130 Slide Out Tray, ExtendoBed, 1500# (EACH) $2,557.00 35-30-2140 Slide Out Tray, ExtendoBed, Dual Direction, 1000# $3,657.00 35-50-1100 Tool Board, .250" Alum (EACH) $220.00 35-85-1100 Turtle Tile, Grating, Per Square Foot $31.00 35-85-2100 Dri-Dek, Grating, Per Square Foot $32.00 24-05-1700 SCBA Stge, LH Fwd Whlwell, 8" Rnd, Cast Prod Door $309.00 24-05-2300 SCBA Stge, LH Rear Whlwell, 8" Rnd, Cast Prod Door $309.00 24-05-5700 SCBA Stge, RH Fwd Whlwell, 8" Rnd, Cast Prod Door $309.00 24-05-6300 SCBA Stge, RH Rear Whlwell, 8" Rnd, Cast Prod Door $309.00 24-09-1100 Ventilation, Fixed Louvers, Body (EACH) $41.00 24-09-2100 Ventilation, 120V Elec, w/Timer, Cmpt (1) Each $385.00 90-08-1300 Folding Water Tank, Fold-A-Tank,2100 Gallon, Alum Frm,22oz $1,348.00 90-08-3700 Folding Tank Mounting, Zico 12V Elec, Right Side $4,937.00 90-08-4100 Folding Tank Cover, Smooth Aluminum, Painted Job Color $866.00 90-08-4200 Folding Tank Cover, Aluminum Diamond Plate $600.00

15.A

CHASSIS OPTIONS BY BOISE MOBILE EQUIPMENT
02-73-2100 Bumper Cmpt, Left, Tool Compartment $564.00 02-73-2200 Bumper Cmpt, Left, Reel Compartment $564.00 02-73-3105 Bumper Cmpt, Center, Tool Compartment $564.00 02-73-3200 Bumper Cmpt, Center, Reel Compartment $399.00 02-73-4100 Bumper Cmpt, Right, Tool Compartment $399.00 02-73-4200 Bumper Cmpt, Right, Reel Compartment $399.00 02-73-5100 Bumper Cmpt, Cover, Vinyl/Hypalon (1) $220.00 02-73-5200 Bumper Cmpt, Covers, Vinyl/Hypalon (2) $440.00 02-73-5300 Bumper Cmpt, Covers, Vinyl/Hypalon (3) $660.00 02-73-6100 Bumper Cmpt, Door, Alum T/P (1) $502.00 02-73-6200 Bumper Cmpt, Doors, Alum T/P (2) $426.00 02-73-6300 Bumper Cmpt, Doors, Alum T/P (3) $1,506.00 02-73-6400 Bumper Cmpt, Door, Alum T/P (1) Full Width $1,430.00 02-73-6500 Bumper Cmpt, Velcro Straps, (2) per Cmpt $165.00 02-73-7100 Bumper Cmpt Light, Auto, w/Door Open Indicator Dash $302.00 02-73-8100 Bumper Guide Poles, Lighted $385.00 02-74-1600 Air Horns, Buell, (2) Hood Mounted $887.00 02-74-2100 Air Horn, Control, Driver, Elec horn or Air horns switch $139.00 02-74-2110 Air Horn, Control, Driver, Siren/air horn, switch $139.00 02-74-2200 Air Horn, Control, Driver, Single Foot Switch $145.00 02-74-2400 Air Horn, Control, Psngr, Single Foot Switch $145.00 02-74-2500 Air Horn, Control, Psngr, Single Dash Switch $139.00 02-74-2510 Air Horn, Control, Psngr, Console $137.00 02-74-2520 Air Horn, Control, Pump Panel $267.00 02-75-2100 Wheel Covers, S/S Liner/Covers, 22.5", Single Axle $907.00 02-76-1300 Exhaust Heat Shield, Under Body Compartments $323.00 02-76-1400 Exhaust, Vertical, Modification $83.00 02-76-1500 Exhaust, Horizontal, Special, Modification $811.00 02-78-1100 Tire Chains, Automatic, On-Spot, per axle, w/mntg brkt $2,454.00 02-79-1200 Cab Step, Fuel Tank Cover, Alum T/P, LH $1,073.00 02-87-1200 Air Brake Compressor, Kussmaul, 12V, 091-9, (100PSI) $846.00 02-87-1400 Air Inlet Plug, Kussmaul, Auto-Eject, LH cab step $708.00 02-88-7100 Protective Sleeve, Air, Fuel, Elec Lines, Fire Resistant Sleeves $715.00 $0.00
PAINT OPTIONS $0.00
80-01-1200 Paint, Cab/Chassis, 2 Door Commercial, Two Tone $6,050.00 80-01-3300 Paint, Chassis Wheels, Six (6), Job Color $1,238.00 80-20-1700 Cmpt Pntg, Zolatone, Grey $2,090.00 81-20-2350 Striping Package, Custom Contact Factory FS19DE05 / FS19DE06 OPTIONS

BODY / COMPARTMENT OPTIONS
24-03-4100 Fenderettes, Body, Polished S/S, 22.5" rims (2) Single Axle $598.00 35-10-0110 Shelf, Adjustable, Alum 1/8" (EACH) $248.00 35-20-1100 Slide Tray, 250#, Alum 3/16", <24"D (EACH) $481.00 35-25-1120 Slide Tray, BME 500#, Alum 3/16", <24"D (EACH) $536.00 35-30-2130 Slide Out Tray, ExtendoBed, 1500# (EACH) $2,557.00 35-30-2140 Slide Out Tray, ExtendoBed, Dual Direction, 1000# $3,657.00 35-50-1100 Tool Board, .250" Alum (EACH) $220.00 35-85-1100 Turtle Tile, Grating, Per Square Foot $31.00 35-85-2100 Dri-Dek, Grating, Per Square Foot $32.00

ELECTRICAL OPTIONS
40-05-1250 UPGRADE Electrical, Multi-Plex, Weldon V-MUX $6,435.00 41-36-3100 Scene Light, Whelen, LED, 4"x 6" (EACH) $394.00 41-36-5100 Scene Light, Whelen, LED, 7"x 9" (EACH) $547.00 41-36-5200 Scene Light, Whelen, PFP1, LED, (EACH) $1,416.00 41-44-3060 UPGRADE Compartment Lighting, Whelen, Fluorent Series $2,599.00 40-32-5050 Stop/Tail Light, Whelen #60R00FRR, LED, 4" x 6" (1) THIRD BRAKE LIGHT $358.00 41-15-1600 Map Light, Havis Shields #C-MAP-T-LED, 12" LED $179.00 41-21-2200 Spotlight, Cab, GO-LIGHT, 2020#, 12V $598.00 42-10-2000 Radio Antenna, Installation (EACH) $124.00 42-10-3600 Radio, Fire, Installation, Purchaser Supplied (EACH) $248.00 42-21-1100 12V Power Outlet, 20 Amp, Cab Dash (EACH) $69.00 42-21-1110 12V Power Outlet, 20 Amp, Console (EACH) $69.00 43-10-2100 Back Up Camera, Tear Drop W/Monitor $1,320.00 45-35-1200 Traffic Emitter, Opticom, Roof Mounted $2,392.00

PAINT OPTIONS
80-01-1200 Paint, Cab/Chassis, 2 Door Commercial, Two Tone $6,050.00 80-01-3300 Paint, Chassis Wheels, Six (6), Job Color $1,238.00 80-20-1700 Cmpt Pntg, Zolatone, Grey $2,090.00 81-20-2350 Striping Package, Custom

15.A

h-gac.com / hgacbuy.org Serving Today • Planning for Tomorrow Authorized Retailer-Distributor-Dealer HGACBuy
V9.17.20 Page 1

HOUSTON-GALVESTON AREA COUNCIL COOPERATIVE

PURCHASING PROGRAM

PLANNED AUTHORIZED RETAILERS/DISTRIBUTORS/DEALER FORM
P
rovide a listing of all planned authorized retailers/distributors/dealers, etc. that may be used during the term of this contract to deliver goods or services. NOTE: awarded contractor remains responsible for all applicable terms of the contract. Form can be duplicated as necessary to include all companies anticipated.

Company Name
Address
City State Zip
Phone Number Fax Number
Contact Person
Authorized Product/Service
Tax ID (Attach W-9)
Company Name
Address
City State Zip
Phone Number Fax Number
Contact Person
Authorized Product/Service
Tax ID (Attach W-9)
S
tate Zip
Fax Number
Company Name
Address
City
Phone Number
Contact Person
Authorized Product/Service
Tax ID (Attach W-9)

15.A

Revised 6.1.18

AMENDMENT No. 2 to CONTRACT No. FS12-19
For
Fire Service Apparatus (All Types)
Between

HOUSTON-GALVESTON AREA COUNCIL
And
Boise Mobile Equipment, Inc.

THIS AMENDMENT modifies the above referenced Contract as follows:

This contract is extended through May 31, 2023 Midnight CT.

Unless otherwise noted, this amendment goes into effect on the date signed by H-GAC. All other terms and conditions of this Contract shall remain unchanged and in full force and effect.

IN WITNESS WHEREOF, the parties have caused this Agreement to be executed by their respective duly authorized representatives.

Signed for Houston-Galveston Area Council, ____________________________________ Houston, Texas Chuck Wemple, Executive Director

Date: _______________________________

Signed for: Boise Mobile Equipment, Inc. ____________________________________

Printed Name & Title: ____________________________________

Date: _______________________________

DocuSign Envelope ID: EF2528FC-2932-45CF-AEAC-5F1DD5392FB1 Matt Stocker Sales Manager
4/27/2022
4/28/2022

15.A

p

COOPERATIVE PURCHASING PROGRAM
Houston-Galveston Area Council of Governments
3555 Timmons, Suite 120, Houston, TX 77027
Phone: 800-926-0234 Fax: 713-993-4548
www.hgacbuy.org
INVITATION TO SUBMIT COMPETITIVE: BIDS PRE-PROPOSAL INVITATION NO.: FS12-19 ISSUE DATE: June 27, 2019
CATEGORY: Fire Service Apparatus (All Types)

PURPOSE OF THIS INVITATION
The Cooperative Purchasing Program ( HGACBuy) of the Houston-Galveston Area Council of Governments is soliciting offerings for the furnishing of products/services as d e s c r i b e d h e r e i n . T h e s e p r o d u c t s / s e r v i c e s m a y b e purchased by any of more than 7000 member local governments, districts, agencies in 49 states across the nation.

Responses must be submitted in an original and one (1) copy, an d shall be subject to the terms, conditions, requirements and specifications detailed in the documents comprising this Invitation. Responses are scheduled to be opened publicly at H-GAC offices on the date indicated. For Bid Invitations, responses will be available for public review until 4:00 p.m. CT that day, and on subsequent days by appointment only. Any Responses submitted later than 1:00 p.m. on the due date will be returned unopened to the bidder/proposer.

PROCUREMENT SCHEDULE & DETAILS
DRAFT SPECIFICATION / INVITATION: May 1, 2019
PRE-BID/PROPOSAL CONFERENCE: June 5, 2019 @ 9:00 a .m. CT; H-GAC Offices FINAL SPECIFICATION / INVITATION: June 27, 2019
BID/PROPOSAL RESPONSES DUE: July 24, 2019 @ 1:00 p.m. CT; H-GAC Clock PUBLIC RESPONSE OPENING: July 24, 2019 @ 2:00 p.m. CT; H-GAC Clock RECOMMENDATIONS TO BOARD: October 15, 2019
CONTRACT START DATE & TERM: December 01, 2019 through November 30, 2021 The documents comprising this Invitation are available via web download at: https://www.hgacbuy.org/bids/ For assistance regarding this Invitation, please contact:

Name: Jackie Palmer Phone: 713-993-2466 E-mail: [email protected]

CONTENTS OF THIS INVITATION
SECTION A - General Terms & Conditions
SECTION B - Product/Service Specific Requirements & Specifications (Final) SECTION C - HGACBuy FORMS (Final)
SECTION D - Pro-Forma (Sample) Contract
This procurement conforms to government requirements for Competitive Procurement.

15.A

LABELING OF SEALED RESPONSE PACKAGE

IMPORTANT:

You must affix an identifying label to the outside of your Sealed Response Package to ensure proper identification and log-in at HGACBuy offices on receipt. HGACBuy i s n o t responsible for any response that might be lost or misdirected due to improper or unclear labeling. Your label should look as follows and should be affi xed conspicuously to the package.

H-GAC Cooperative Purchasing
Sealed Bid/Proposal No. FS12-19

DO NOT OPEN IN MAIL ROOM

Responses by E-mail or FAX will not be acceptable. Hard copies , as described herein, plus appropriate electronic media are required.

15.A

Revised: 04/16/18 Page 1 of 20

SECTION A

GENERAL TERMS & CONDITIONS

FOR BIDS AND PROPOSALS
INVITATION NO. FS12-19
DESCRIPTION: Fire Service Apparatus (All Types)

TABLE OF CONTENTS

1.  INTRODUCTION ................................................................................................................................................ 2

2.  DEFINITIONS, ABBREVIATIONS & ACRONYMS ........................................................................................ 2

3.  NON-BINDING ORAL COMMENTS ................................................................................................................ 4

4.  STRUCTURE OF RESPONSE ............................................................................................................................ 4

5.  BASIC REQUIREMENTS & CONDITIONS ...................................................................................................... 4

6.  OFFEROR'S AUTHORIZED SIGNATORY ....................................................................................................... 5

7.  SURETY FOR INSURANCE .............................................................................................................................. 6

8.  CONFIDENTIAL / PROPRIETARY MATERIALS ........................................................................................... 6

9.  REFERENCES ..................................................................................................................................................... 6

10.  INSURANCE ................................................................................................................................................... 6

11.  OFFEROR CERTIFICATIONS ....................................................................................................................... 7

12.  HISTORICALLY UNDERUTILIZED BUSINESS (HUB) PARTICIPATION.............................................. 7

13.  NON-RESIDENT RECIPROCAL SALES ACT ............................................................................................. 8

14.  TEXAS MOTOR VEHICLE COMMISSION CODE & LICENSING ............................................................ 8

15.  INTENT AND SCOPE OF SPECIFICATIONS .............................................................................................. 8

16.  REQUIREMENTS APPLICABLE TO PHYSICAL GOODS ......................................................................... 8

17.  PRODUCT CODES ......................................................................................................................................... 8

18.  SPECIFIC DESCRIPTIVE REFERENCES ..................................................................................................... 9

19.  MANUALS ...................................................................................................................................................... 9

20.  STANDARD FEATURES & OPTIONS ......................................................................................................... 9

21.  WARRANTIES, SALES & SERVICE .......................................................................................................... 10

22.  H-GAC ORDER PROCESSING CHARGE .................................................................................................. 11

23.  PRE-PAYMENTS AND DISCOUNTS ......................................................................................................... 11

24.  INSPECTION / TESTING ............................................................................................................................. 11

25.  PRODUCT DELIVERY ................................................................................................................................ 11

26.  OFFERED PRODUCT ITEM VARIANCES ................................................................................................ 11

27.  REQUIREMENTS FOR SUBMISSION OF A RESPONSE ......................................................................... 11

28.  CLARIFICATION TO SPECIFICATIONS & REQUIREMENTS ............................................................... 13

29.  INCONSISTENT INFORMATION ............................................................................................................... 14

30.  REJECTION OF RESPONSES ...................................................................................................................... 14

31.  WITHDRAWAL OR MODIFICATION OF RESPONSES .......................................................................... 14

32.  RESPONSE EVALUATION ......................................................................................................................... 14

33.  ORDER OF PRECEDENCE PRIOR TO CONTRACT AWARD ................................................................ 15

34.  AWARD OF CONTRACT ............................................................................................................................ 15

35.  PRO-FORMA CONTRACT .......................................................................................................................... 15

36.  CONTRACT TERM ...................................................................................................................................... 15

15.A

Revised: 04/16/18 Page 2 of 20

37.  PERFORMANCE & PAYMENT BOND ...................................................................................................... 15

38.  CHANGE ORDERS ....................................................................................................................................... 15

39.  DUPLICATION OF TERMS OR STATEMENTS ........................................................................................ 15

40.  PUBLICITY ................................................................................................................................................... 15

41.  TAXES ........................................................................................................................................................... 16

42.  DRUG FREE WORKPLACE ........................................................................................................................ 16

43.  PRODUCT NOTICES & MAILINGS ........................................................................................................... 16

44.  HANDLING OF ORDERS & PAYMENTS .................................................................................................. 16

45.  PRICE CHANGES ......................................................................................................................................... 17

46.  CONTRACT ITEM CHANGES .................................................................................................................... 17

47.  FORCE MAJEURE ........................................................................................................................................ 18

48.  PERFORMANCE UNDER CONTRACT ..................................................................................................... 18

49.  CONTRACTOR ORIENTATION/TRAINING ............................................................................................. 18

50.  LEGAL & CONTRACTUAL REMEDIES ................................................................................................... 19

51.  NATIONWIDE SALES OPPORTUNITIES .................................................................................................. 20

1. INTRODUCTION
The Houston-Galveston Area Council ( H-GAC) is a "Government-to-Government" procurement service for States , State Agencies, Local Governments, Districts, Authorities, and qualifying Not-for-Profit Corporations (End Users).

End Users become Members o f t h e H-GAC Cooperative Purchasing Program ( HGACBuy) by executing an Interlocal Contract, which is free of cost and evergreen unless cancelled. HGACBuy, acting on behalf of Members, is soliciting competitive offerings for the furnishing of pro ducts and/or services, as described elsewhere, which MAY be purchased by Members during the contract term. Members using the Program issue purchase orders directly to HGACBuy contractors.

2. DEFINITIONS, ABBREVIATIONS & ACRONYMS
The following definitions, abbreviations and acronyms may be found in these specifications, and shall be interpreted herein as specified below.

Definitions and Abbreviations:

Acceptance. Acceptance takes place when the End User agrees with the Contractor that the terms and conditions of the contract have been met and verified. Acceptance is not the same as Receipt, and can only occur after intact shipping, inspection by End User, and any onsite testing that has been stipulated as part of the order Aggregate/Single Occurrence. The term "aggregate" in insurance terms is the sum of all claims against a specific policy for a specific loss incident. The term "single occurrence" differentiates between multiple claims and single claims against a specific policy. The inherent value of a poli cy's aggregate value is less important to an End User than is the value of a single claim as stated under "single occurrence." Approved. Acceptable to the "authority having jurisdiction." ARO. “After Receipt of Order”. Use d in conjunction with a defined t i m e p e r i o d ( u s u a l l y d a y s o r w e e k s ) t o establish the delivery or lead time pursuant to any individual purchase transaction. In the case of orders for bodies which will be mounted on a customer furnished cab/chassis, the t e r m A R O s h a l l b e c o n s t r u e d t o m e a n “ A f t e r Receipt Of Cab/Chassis”.

Authority Having Jurisdiction. The authority shall be either H-GAC or the relevant End User based on the requirements as stated in each specification item. Unless specifically stated, the authority shall be H-GAC.

Bidder. Any entity that submits a competitive bid to this Invitation. (See also "Offeror") Change Order. Request by an End User for a change in the composition of an already submitted purcha se order, for example to change quantity ordered, add or delete items, etc.

Contract. Specifically, a contract between H-GAC and a successful Offeror which is executed based on an award made pursuant this Invitation.

15.A

Revised: 04/16/18 Page 3 of 20

Contract Pricing Worksheet. The standard H-GAC form to by used by Contractor in preparing a quotation to an End User, upon which End User's purchase order will be based. Contractor may use another quotation form provided it contains required information, and only if approved by H-GAC.

Contractor. The contracted business entity responsible for fulfilling a contract executed pursuant to this Invitation.

Dealer/Distributor. A duly authorized and/or franchised business entity which sel ls and services a manufacturer’s product in a specified marketing area.

Defect. A discontinuity in a part or a failure to function that inter feres with the service or reliability for which the part was intended.

Electronic Media. As used herein, means computer based media such as 100mb Zip Disk, CDRom, e-mail, e-mail attachment, file downloaded from the web, etc.

End User. (See "Participant" and “Member”)
Listed. Equipment or materials included in a list published by an orga nization, acceptable to the "Authority Having Jurisdiction" and concerned with product evaluation, that condu cts periodic inspection of production of listed equipment or materials and whose listing states either that the equipment or materials meet appropriate standards or has been tested and found suitable for use in a specified manner. NOTE: The means for identifying listed equipment may vary for each organization concerned with product evaluatio n, some of which do not recognize equipment as listed unless it is also labeled. The "authority having jurisd iction" should utilize the system employed by the listing organization to identify a listed product.

Manufacturer. The person or persons, company firm, corporation, partnership, or other organization responsible for taking raw materials or components and making a finished product.

May. A term indicating a permissive use or an acceptable alternative to a specified requirement.

Member. An authorized Participant in the Program. (See "Participant" and “End User”) Motor Vehicle. The meaning of this term shall be based on the legal definiti on ascribed to it by the laws and/or regulations of the state in which any specific sale made pursuant to a Contract takes place.

Must. A term indicating a mandatory requirement.

Offer or Offering. Any product or service offered in reply to this Invitation.

Offeror. Any entity that submits a competitive bid or proposal in response to this Invitation. Bidder or Proposer.

Participant. Generally, any qualifying governmental or non-profit entity which has executed an Interlocal Contract for cooperative purchasing services with H-GAC.

Product Liability Insurance. Failure of Components and/or assembled equipment resulting in personal injury, disability or death and/or property damage is covered under the product liability insurance provisions.

Product or Product Item. Any of the specific goods, materials, equipment or service(s) specified in this Invitation.

This term encompasses the base line item itself, and any and al l accessories, options, modifications, ancillary services, assembly, testing, etc. that may be included in the delivered Product.

Proposer. Any entity that submits a competitive proposal in response to this Invitation. (See also "Offeror") Purchaser. The End User having responsibility for the specification, requisition, orde ring and acceptance of the Product or Service. (See also "End User")
Purchasing Authority. The agency that has sole responsibility and authority for neg otiating, placing and, if necessary, modifying any solicitation, purchase order, or other award issued by a governing body [H-GAC].

Quotation. See "Contract Pricing Worksheet".

Receipt. Receipt takes place when a Product or Service is delivered to an End User and a document is executed that establishes that the Produ ct is now in the possession of t he End User or that the Service has been completed.

Receipt DOES NOT connote or imply Acceptance.

Response. All or part of any offering submitted in response to this Invitation.

Shall. A term indicating a mandatory requirement or action.

Should. A term indicating a recommended or advised response to a specified requirement.

Vendor. A manufacturer's representative or dealer authorized to make sales and supply parts and service.

Acronyms:

ANSI = American National Standards Institute
ASTM = American Society for Testing and Materials
ASME = American Society of Mechanical Engineers
CFR = U.S. Code of Federal Regulations

15.A

Revised: 04/16/18 Page 4 of 20

DOJ = U.S. Department Of Justice
DOT = U.S. Department Of Transportation
EPA = U.S. Environmental Protection Agency
FAA = Federal Aviation Administration
FMVSS = U.S. Federal Motor Vehicle Safety Standards
H-GAC = Houston-Galveston Area Council of Governments
IEEE = Institute of Electrical and Electronics Engineers MVD = Motor Vehicle Division of Texas Department of Transportation NFPA = National Fire Protection Association
NHTSA = National Highway Traffic Safety Administration
NIOSH = National Institute For Occupational Safety And Health NIST = National Institute of Standards and Technology
NTEA = National Truck Equipment Association
OSHA = U.S. Occupational Safety and Health Administration RRC = Railroad Commission of Texas
SAE = Society of Automotive Engineers
TBPC = Texas Building and Procurement Commission (formerly GSC) TxDOT = Texas Department Of Transportation
UL = Underwriter's Laboratories Inc.

VTCS = Vernon's Texas Civil Statutes

3. NON-BINDING ORAL COMMENTS
No oral comment, utterance or response made by any employee, member, or agent of H-GAC or any Member of the Cooperative Purchasing Program shall be considered factual or binding with regard to this Invitation, or any contract awarded as a result of this Invitation. Valid and binding term s, conditions, provisions, changes or clarifications, or requests thereof, shall ONLY be communicated written form.

4. STRUCTURE OF RESPONSE
Depending on the Product or Servi ce, market structures and sale s practices can differ substantially. For example, dealers may sell into any market or may be restricted to certai n territories, manufacturers may sell direct or may be limited by law to selling thru independent dealerships, etc. H-GAC’s objective is to ensure that End Users , no matter where located, can buy contracted products/services and receive quality and timely service and support, while at the same time allowing for the most appropriate and effectiv e response to this Invitation. Therefore, responses to this Invitation will be accepted in conformance with the following scenarios and requirements:

A. Single Respondent Acting Alone Or As "Lead" For A Group:

Offeror shall complete and sign a Form A and, if contracted, shall be solely responsible for all contra ctual requirements including administration, processing of purchase o rders and handling of payments for transactions which may involve other dealers who actually deliver the products or services.

B. Multiple Respondents Acting Jointly:

A single Response shall be submitted, and each party to the Response shall complete and sign a separate Form A to be included in the single Response. If the Response is suc cessful each party shall sign a separate contract with H-GAC and shall be responsible for compliance with all terms and con ditions. Only those which have executed a written contract with H-GAC may process purchase orders and payments.

In any event, Offeror may be a party to one, and only one, response.

5. BASIC REQUIREMENTS & CONDITIONS
a. The final requirements and specifications contained herein may be different, perhaps materially, from those in the “Invitation To Attend Pre-Bid / Pre-Proposal Conference”, i f any. It is Offeror’s sole responsibility to thoroughly examine and review a ll documentation associated with this Invitation, including any Addendums, and to insure that any response submitted complies in every respect with all requirements.

15.A

Revised: 04/16/18 Page 5 of 20

b. Any Addendum to this Invitation which may be required prior to the Response due date will be delivered to those prospective Offerors of record who have previously obtain ed a copy of this Invitation from H-GAC.

Prospective Offerors shall be responsible for obtaining all documents relating to submission of a Response. c. Offeror shall thoroughly examine any drawings, specifications, schedul es, instructions and any other documents, supplied as a part of this Invitation, and is solely responsible for understanding and compliance. d. H-GAC shall not be liable for Offeror's incomplete documentation, or for any costs associated with preparation and submission of any Response hereto. Additionally, all components of any Response become the property of H-GAC, and shall be considered to be in the public domain. e. Offeror shall make all investigations necessary to become thoroughly i nformed regarding any plan and/or infrastructure that may be required to support delivery of any Product or Service covered by this Invitation. No plea of ignorance by Offeror stemming from failure to investigate conditions that may now o r hereafter exist, shall be accepted as a basis for varying H-GAC's requirements , or Offeror's/Contractor's obligations or entitlements.
f. Requests for changes to the requirements or specifications here in must be in writing (e-mail, fax, letter) and must be received by H-GAC no later than fifteen (15) calendar days prior to the Response Due Date. H-GAC will review such requests, but may or may not make changes at its sole discretion. Changes, if any, will only be made by written Addendum sent to addressees of record. In any event, it is Offeror's sole responsibility to insure that any and all Addendums which may have been issued have been received and addressed. g. By submission of a response, Offeror expressly understands and agrees that all terms and conditions herein will be part of any subsequent contract that is executed pursuant to this Invitation. h. Offeror is advised that all H-GAC contracts are subject to the le gal requirements established in any applicable Local, State or Federal statute.
i. Offeror/Contractor must be in compliance with all licensing, permitting, registra tion and other applicable legal or regulatory requirements imposed by any governmental au thority having jurisdiction. It is Offeror/Contractor’s responsibility to insure that this requirement is met, and to supply to H-GAC upon request, copies of any license, permit or other documentation bearing on such compliance. j. Unless otherwise established elsewhere in this Invitation, NO m inimum purchase quantities or spending levels are provided or guaranteed by H-GAC or any End User.
k. This Invitation is not meant to restrict competition, but rather is intended to allow for a wide range of responses. l. Responses which are 'qualified' with conditional clauses or alt erations of or exceptions to any of the terms and conditions in this Invitation may be deemed non-compliant at H-GAC's sole discretion. m. The term ‘ Offeror’, or derivative thereof, shall become synonymous with ‘ Contractor’ for any successful Offeror recommended for a contract pursuant to this Invitation. n. H-GAC reserves the right to:
 Reject any and all offers received in response to this Invitation.  Reject any part of an offer received in response to this Invitation.  Determine the correct price and/or terminology in the event of any discrepancies in any response.  Accept a response from, and enter into agreement with, other than the lowest price Offeror.  Accept responses and award contracts to as many or as few Offerors as H-GAC may select.  Amend, waive, modify, or withdraw (in part or in whole) this Invitation, or any requirements herein.  Hold discussions with Offerors, although award may be made without discussion.  Request an Offeror to give a presentation of the Response at a time and place scheduled by H-GAC.  Exercise any of these rights at any time without liability to any Offeror. o. H-GAC reserves the right to determine that conditions exist which pr event the public opening of responses on the date and at the time advertised, and to reschedule the publ ic opening for a future date and time. Responses received by H-GAC by the original deadline will be secured unopened until the re scheduled opening date and time, and those having timely submitted such responses will be notified.

6. OFFEROR'S AUTHORIZED SIGNATORY
The signatory shall be authorized to sign and contractually bin d Offeror, and shall sign any and all Response documentation requiring a signature.

15.A

Revised: 04/16/18 Page 6 of 20

7. SURETY FOR INSURANCE
Contractor shall be responsible for using a surety company properly licens ed by any and all states in which Contractor will do business with Participants. The surety company shall not expose itself to any loss on any one risk in an amount exceeding ten percent (10%) of its surplus to poli cy holders, provided any risk or portion of any risk shall have been reinsured, and such reinsurance shall be deduct ed in determining the limitation of risk applicable to H-GAC's insurance requirements.

8. CONFIDENTIAL / PROPRIETARY MATERIALS
All documentation submitted as part of Offeror's response to this Invitation will be considered to be in the pu blic domain and may be made available to Members and others, after contract award, upon properly submitted request. If Offeror submits documents marked “confidential” or “proprietary”, the Response may be deemed non-compliant.

9. REFERENCES
a. Offeror shall list the names of at least five government agencies with in the continental United States which have purchased from Offeror products or services similar to those covered by this Invitation, within the last two years. H-GAC reserves the right to determine if such products or services are appropriately similar. b. Offeror may provide reference informati on in whatever format desired, but each should include the following specific information:
 Agency name
 Contact person name
 Address
 Phone & Fax numbers
 Description of product(s) or service(s) and date sold c. Other information, including criticism however learned, may be used by H-GAC in evaluation of responses.

10. INSURANCE
a. Unless otherwise stipulated in Section B, Offeror/Contractor must have the following insurance and coverage minimums:

General liability insurance with a Single Occurren ce limit of at least $1,000,00 0.00, and a General Aggregate limit of at least two times the Single Occurrence limit.

Product liability insurance with a Single Occurren ce limit of at least $1,000,00 0.00, and a General Aggregate limit of at least two times the Single Occurrence limit for all Products except Automotiv e Fire Apparatus. For Automotive Fire Apparatus, see Section B – Product Specific of this Invitation.

Property Damage or Destruction insurance is required for coverage of End User owned equipment while in Contractor's possession, custody or control. The minimum Single Occurren ce limit is $500,000.00 and the General Aggregate limit must be at least two times the Single O ccurrence limit. This insurance may be carried in several ways, e.g. under an Inland Marine policy, as part of Automobile coverage, or under a Garage Keepers policy. In any event, this coverage must be specifically and c learly listed on insuran ce certificate(s) submitted to H-GAC.
b. Insurance coverage shall be in effect for the length of any con tract made pursuant to this Invitation, and for any extensions thereof, plus the number of days/months required to deliver any outstanding order after the close of the contract period.
c. Original Insurance Certificates must be furnished to H-GAC on request, showing Offeror/Contractor as the insured and showing coverage and limits for the insurances listed above. d. If any Product(s) or Service(s) will be provided by parties oth er than Offeror/Contractor, all such parties are required to carry the minimum insurance coverages specified her ein, and if requested by H-GAC, a separate insurance certificate must be submitted for each such party. e. H-GAC reserves the right to contact insurance underwriters to confir m policy and certificate issuance and document accuracy.

15.A

Revised: 04/16/18 Page 7 of 20

11. OFFEROR CERTIFICATIONS
Offeror, by submission of a Response hereto, makes the followin g certifications under penalty of perjury and possible contract termination if any of these certifications are found to be false.

Non-Collusive Response
a. The prices in the Response have been arrived at independently without collusion, consultation, communication, or agreement for the purpose of restricting competition, as to any matter relating to such prices with any other Offeror or potential competitor.
b. The prices which have been quoted in the Response (unless other wise required by law), have not been knowingly disclosed by Offeror and will not be knowingly disclosed by Offeror prior to the public response opening, either directly or indirectly, to any other Offeror or competitor. c. No attempt has been made or will be made by Offeror to induce any other person, partnership or corporation to submit or not to submit a response for the purpose of restricting competition.

Non-Biased Specifications
This Invitation contains no requirements considered to be undul y biased in favor of Offeror or any other Offerors that may be competing for this procurement.

No Financial Interest or Other Conflict
a. No H-GAC officer, employee, Board of Directors member or member of any H-GAC board or commission, nor family member of any such person, has a financial interest, direct or indirect, in Offeror or in any contract Offeror might enter into with H-GAC.
b. No economic or employment opportunity, gift, loan, gratuity, special discount, trip, favor or service has been, or will be, offered or given to any officer, employee, Board of Directors member, or member of any H-GAC board or commission, nor to any family member of any such person.

Debarment and Suspension Status
a. Offeror is not currently debarred, suspended, proposed for debarment, declared ineligible or voluntarily excluded from covered transactions by any government agency, no r is Offeror an agent of any person or entity that is currently debarred, suspended, proposed for debarment, declared ineligible or voluntarily excluded from covered transaction by any government agency.
b. Offeror has not within a three year period preceding this Invitation b een convicted of or had a civil suit judgement renedered against Offeror for commission of fraud or a cr iminal offense in connection wi th obtaining, attempting to obtain or performing a public transact ion or contract under a public transaction; violation of federal or state antitrust statutes or commission of embezzlement, theft, forgery, bribery, falsification or destruction of records, making false statement, or receiving stolen property. c. Offeror is not presently indicted for or otherwise criminally or civil ly charged by a government entity (federal, state, or local) with commission of any of the offenses enumerated above. d. Offeror has not, within a three year period preceding this Invi tation, had any government (federal, state, or local) transactions terminated for cause or default.

Insurance Coverages
Offeror has and will maintain insurance coverage in accordance with the requirements of this Invitation.

Licensing & Permits
Offeror(s) has (have) all licenses and/or permits, required by any and al l governmental entities having jurisdiction, to legally sell the products/services offered.

12. HISTORICALLY UNDERUTILIZED BUSINESS (HUB) PARTICIPATION a. To satisfy Texas' statutory requirements [Government Code, Chapter 2161, Subchapter D], H-GAC requires all Offerors to supply information in any bid/proposal response listing (1) the total number of subcontracts and (2) the total number of HUB contracts applicable to the Products or S e r v i c e s o f f e r e d i n t h e r e s p o n s e . L o c a l governments often require this information for their own report ing requirements prior to placing orders through the H-GAC Cooperative Purchasing Program.
b. Offeror must complete Form B and include subcontracts with HUB’s that provide any materials or services related to sales that may be made thru H-GAC’s Cooperative Purchasing Program.

15.A

Revised: 04/16/18 Page 8 of 20

13. NON-RESIDENT RECIPROCAL SALES ACT
As required by Texas Civil Statutes in the award of contracts, an offeror which is not a Texas resident business must determine if its state of residence prohibits award of governme nt contracts to Texas resident offerors without penalty. If Offeror’s resident state DOES penalize Texas offerors, Offeror must provide this information along with a copy of its applicable resident state's statute in the Response.

14. TEXAS MOTOR VEHICLE COMMISSION CODE & LICENSING
Sales of motor vehicles in the State of Texas are subject to th e Texas Motor Vehicle Commission Code. If this Invitation includes any motor vehicle to be sold in the State o f Texas, Offeror certifies by submission of a response hereto that all required Texas Motor Vehicle Commission license s are in place and current, and that copies of all such licenses have been submitted with the Response. Further, it shall be Contractor's responsibility to keep current all required Texas Motor Vehicle Commission licensing d uring the term of the contract, and to furnish license copies at any time on request by H-GAC. I f Contractor does not maintain current licensing, H-GAC reserves the right to immediately terminate the contract.

NOTE: In accordance with the Texas Motor Vehicle Commission Code, c ontracts for motor vehicles to be sold within the state of Texas may be made ONLY with properly licensed Texas Motor Vehicle Dealers. Therefore, to be considered for a contr act covering Texas End Users, the Response must include a Form A from a licensed Texas Motor Vehicle Dealer

15. INTENT AND SCOPE OF SPECIFICATIONS
a. The intent of the specificat ions herein is to provide Offeror with sufficient information concerning the Products/Services to be contracted such that Offeror can prepare and submit an acceptable Response. b. The specifications may be detailed or general in nature with regard to any particular Product/Service. Where not otherwise specified, details of construction, materials, or the way in which services will be provided, are left to the discretion of the Offeror, provided only that any offering shall conform, as a minimum, to best Industry standards and practices and to what is currently being sold in the marketplace. c. Responses shall be considered only from Offerors that have established good reputations in their markets, and who furnish satisfactory evidence of ability to supply the Products/Services specified herein. d. Offeror shall show proof of ability to provide to End Users prompt and competent service, including parts if applicable, for all Products/Services covered by this Invitatio n, by proper completion of a Service Organization Document as described elsewhere herein.

16. REQUIREMENTS APPLICABLE TO PHYSICAL GOODS
In the case of physical goods (e.g. equipment, material, suppli es, as opposed to services), all Products offered must, unless otherwise stipulated in Section B:
a. Be new, unused, and not refurbished.
b. Not be a prototype insofar as the general design, operation and performance. This requirement is NOT meant to preclude Offeror from offering new models or configurations which incorporate i mprovements in a current design or add functionality, but which in such new model or configuration may be new to the marketplace. c. Include any and all accessories which may or may not be specifi cally mentioned herein, but which are normally furnished or which are necessary to make a delivered Product re ady for its intended use. Such accessories shall be assembled, installed and adjusted such that the Product is ready for continuous operation at time of delivery. d. Have assemblies, sub-assemblies and component parts that are st andard and interchangeable throughout the entire quantity of a particular Product as may be purchased simultaneously by any individual End User. a. Be designed and constructed using current industry accepted engineering and safety practices, and materials. b. Be available for inspection at any time prior to or after procurement.

17. PRODUCT CODES
Unless otherwise addressed in Section B of this Invitation, the following requirements shall apply:

15.A

Revised: 04/16/18 Page 9 of 20

a. Each Product/Service offered shall be uniquely identified using a n H-GAC Product Code, which shall be determined as described in Section B of this Invitation. Offeror s h a l l o f f e r O N L Y O N E P r o d u c t f o r a n y particular Product Code. For example, Offeror may wish to submit a bid for Product Code ABC and may have another offering that also meets the requirements for ABC. Offeror MAY NOT submit two offerings for ABC.

The alternate offering that also meets the requirements for ABC must be offered as an option "upgrade/downgrade" to ABC on Form E.
b. Pricing for optional upgrades or downgrades to base bid items s hould be quoted as an “adder” or “deduct” amount as appropriate, to be applied to the offered price of the base Product Item listed on Form D. c. Base bid items and their associated HGACBuy Product Codes are included in the Section B and/or on Form D. d. Selection of Product Codes for which to submit an offer is at Offeror’s sole discretion.

18. SPECIFIC DESCRIPTIVE REFERENCES
Except for Base Product Items listed on Form D, any reference to a specific cat alog, data sheet, form, brochu re, model name or number, etc. used herein to describe an item such as an option or accessory is only descriptive and is not to be considered restrictive unless otherwise noted. Such references are normally used only to indicate a type, general description, level of quality and/or required performance standards.

19. MANUALS
Unless otherwise specified or superceded herein, each Product d elivered under an H-GAC contract, and if applicable any options thereto, shall be supplied with at least one (1) copy of a safety and operating manual. The cost of any such manuals must be included in the base price for any Product Item offered hereunder. If more detailed and technically orientated parts and maintenance manua ls are available for a Product or option, at a cost, they shall be offered as options on the FORM designated herein for such options, or elsewhere in the Respon se as may be directed herein.

20. STANDARD FEATURES & OPTIONS
The following requirements are applicable primarily to physical goods.

Standard Features
a. The stated minimum requirements for all Products listed herein include what H-GAC c o n s i d e r s t o b e “standard” features. Even though such features might normally be offered as options rather than as standard, they are nonetheless considered to be standard in this Invitati on, and must be included in the base price for any Product offered. Such features SHOULD NOT be offered as options except as deducts for their omission fro m the base Product.
b. If it is unclear in the Response that an H-GAC standard feature is included in the base price, it will be ass umed that such is the case. If awarded a contract Offeror will be expected to sell the Product with all H-GAC specified standard features included in the base price. c. Any feature or accessory normally offered by manufacturer as "standard" shall be considered a standard feature and shall be included in the base price of any offering, even t hough not specifically listed as a requirement in H-GAC’s specifications. Such features SHOULD NOT be offered as options except as deducts for their omission from the base Product.

Options - General
a. Options are considered to be any features or accessories, other than H-GAC's and Manufacturer's "standard" features or accessories.
b. Options should be offered on the FORMS designated for quoting options. Each option should be listed and described on a separate line , and should include any Manufacturer's/Dealer's code number. I f no Manufacturer's/Dealer's code number exists, Offeror should create one. c. Prices for all offered options shall be assumed to include any installation or mounting required to make it a fully functional component of the Product, unless otherwise stated in Offeror's response.

Required Options

15.A

Revised: 04/16/18 Page 10 of 20

a. Product specifications in this Invitation may include H-GAC "Required Options". If so, Offeror must quote a price for ALL such options, and, if there is an H-GAC Option Code provided in this Invitation for such options, it MUST be used as part of the description.
b. For any specific "Required Option", Offeror may quote an equivalent so long as its design and performance are as good as, or better than, the specified option item. Response s which do not include pricing for Required Options may be considered non-compliant.

Other Options
a. "Suggested" or "Other" options may be listed for any particular Product in this Invitation, and Offeror i s encouraged to quote pricing for such options. The extent of of fered options in any response may be taken into consideration as part of the award criteria, at H-GAC's sole discretion. b. Offeror is encouraged to include options for non-equipment items that may be applicable to a sale, such as:

Extended Warranties, Maintenance Agreements, Buy-back or Trade- In Agreements, Out-of-state Delivery Charges, Quantity or Special Discounts, Extended Training Classes, etc.

Published & Unpublished Options
a. H-GAC Cooperative Purchasing Program (Program) contracts are aw arded through a public competitive bid or proposal (RFP) process. Further to that process, Program polic y considers an 'option' listed and priced in a bid or RFP Response: (1) To be a " Published Option"; (2) To be part of any awarded contract; and (3) To be available for purchase by Program members separately and indepe ndently from associated base line items.

However, since Published Options may have not been subjected to the same scrutiny as the associated base line items, it cannot be concluded they were directly competed. The refore, pursuant to Local Government Code 252.021(a), purchase of a published option costing more than $5 0,000 shall not be allowed. Furthermore, H-GAC reserves the right at its sole discretion to disallow purchase of any Published Option through the Program if deemed contrary to the intent of the law.
b. Any option that has not been listed and priced in the Response is considered to be an “ Unpublished Option”.

Unpublished Options may be sold, but only in connection with th e sale of a base Product Item, and only insofar as the total cost of all Unpublished Options remains below twen ty five percent (25%) of the total summed cost of the base Product(s) plus any Published Options.
c. No Published or Unpublished Option may be sold which essentiall y converts a Product such that it competes with a Product Item awarded to another contractor.

21. WARRANTIES, SALES & SERVICE
Unless otherwise addressed in Section B, the following requirements shall apply:
a. Offeror must be a properly franchised dealer authorized to sell and service, including warranty service, all products offered and sold in response to the bid invitation or under any H-GAC contract. b. Offeror shall provide detailed Parts and Labor Warranty information wi th the Response. If Offeror submits a warranty with the Response which does not meet the minimum requ irements herein, Offeror agrees by submission of a Response that such warranty shall be considered to be amended to meet those minimums. c. Warranties shall be manufacturer's standard and shall be inclus ive of any other warranty requirements which may be stipulated elsewhere herein.
d. Any warranties offered by a dealer shall be in addition to the manufacturer’s standard warranty, and shall not be a substitute for such. Offeror's base price for any Product shall be inclusive of the standard warranty. e. Complete warranty information will be supplied to End User with each Product sold. a. Warranties need not apply to normal maintenance service or adjustments, or to any product reasonably shown to have been repaired or altered in any way so as to affect its st ability, or to any product which has been subject to misuse, negligence, or accident.
f. Offeror/Contractor is encouraged to offer extended warranties as an option. g. Neither H-GAC n o r End User assume any warranty or liability on Contractor’s behalf unless made or assumed in writing, initiated by Contractor, and agreed to in writing by H-GAC or the End User respectively. h. Contractor shall be responsible for the execution and effectiveness of all product warranty, and shall be the sole source for solution to problems arising from warranty clai ms. Contractor agrees to respond directly to correct warranty claims and to ensure reconciliation of warranty claims that have been assigned to a third party.

15.A

Revised: 04/16/18 Page 11 of 20

22. H-GAC ORDER PROCESSING CHARGE
H-GAC will levy an Order Processing Charge on Contractor for each sale done thru the H-GAC contract, with the exception of orders for motor vehicles . Any bid pricing submitted will be considered to include the Charge. The amount of the applicable charge shall be per the most current H-GAC schedule. For motor vehicle orders, the Processing Charge shall be levied on and paid by the End User.

23. PRE-PAYMENTS AND DISCOUNTS
a. Progress, pre-payment and special discounts of any kind may be offered and detailed in the Response. Such discounts shall be clearly explained, but shall not be a determ ining factor in awarding contracts except in the case of tie offerings.
b. Quantity discounts applicable to similar Products sold to one o r more End User Departments may be offered.

Determination as to product similarity shall rest solely with Contractor. c. For specific purchases, any proposed quantity, pre-payment or s pecial discounts shall be clearly shown on the Contract Pricing Worksheet.

24. INSPECTION / TESTING
All Products sold pursuant to this Invitation shall be subject to inspection/testing by or at the direction of H-GAC and/or the ordering End User, either at the delivery destination or the place of manufactur e. In the event a Product fails to meet or exceed all requirements of this Invitation, an d unless otherwise agreed in advance, the cost of any inspection and/or testing, shall be borne by the Contractor.

25. PRODUCT DELIVERY
Unless otherwise addressed in Section B, the following requirements shall apply:
a. Title to goods, and responsibility and liability for loss and/o r damage in shipping pass to End User at the delivery destination after receipt and acceptance have taken pl ace. Cost of shipping/delivery shall be paid by End User unless otherwise agreed to by Contractor. If Contractor will be paying for shipping/delivery, shipping terms must be "F.O.B. Destination, Freight Prepaid". If End User will be paying for shipping/delivery, shipping terms must be “F.O.B. Destination – Freight Collect”. b. The details for the application and calculation of shipping and delivery charges must be stated in the Response on Form E. Any freight, shipping or delivery charged to End User will be prepaid and added to the invoice, and will be clearly shown an any Contract Pricing Worksheet or other quote presented to the End User. c. The estimated delivery time afte r receipt of order (ARO), inclu sive of Saturdays, Sundays and holidays, for all Products offered must be stated in the Response. Actual delive ry for any particular order must be confirmed with End User at time of order placement, and must be stated clearly on the Contract Pricing Worksheet. d. Contractor shall be responsible for delivery and Acceptance according to the requirements of the Contract and the Purchase Order.
e. Contractor shall advise End User prior to making any shipment/delivery, and shall make such shipment/delivery in accordance with End User's requirements, providing only that such arrangements do not contravene any requirement of the H-GAC contract unless agreed to by Contractor. f. The execution of all required tests, certifications and/or lice nsing, and costs thereof, shall be the responsibility of Contractor. Upon request by End User o r H-GAC, Contractor shall provide any documentation or certification related to such tests, certifications or licensing.

26. OFFERED PRODUCT ITEM VARIANCES
Any variance in the specifications or performance of Products o ffered pursuant to this Invitation shall be acceptable to H-GAC only insofar as it MEETS or EXCEEDS the specifications and requirements of this Invitation.

27. REQUIREMENTS FOR SUBMISSION OF A RESPONSE
Unless otherwise addressed in Section B, the following requirements shall apply:
a. Responses shall be submitted in two complete printed sets inclu ding an Original and one (1) Copy in separate "hard side" three-ring binders. The outer spine of each binder shall be labeled showing this Invitation No., Offeror Name, and either "Original" or " Copy", as applicable. The Ori ginal printed response will be

15.A

Revised: 04/16/18 Page 12 of 20

considered to be the binding Response in case of any conflicts between printed copies and electronic copies.

Except for required forms, H-GAC Invitation documents should not be included in the Response. b. The Original and the Copy shall be submitted complete, except t hat the Electronic Media should be submitted only with the Copy.
c. All required H-GAC FORMS and documents shall be properly completed, without exception o r Offeror’s Response may be deemed non-compliant. Offeror may not modify the format of any H-GAC FORM in any way. Offeror may photocopy or print blank FORMS as needed. Information submitted on the printed copies of the FORMS may not be handwritten except for signatures and initials. It is Offeror's responsibility to insure that printed FORMS are clear and legible. Handwritten and illegible entries may be rejected. Offeror's printed, stamped or typed name shall appear on every FORM submitted in the Response. d. The entire response submission shall also be submitted on electronic media, including all requ ired H-GAC FORMS. Offeror is strongly advised to make and work with copies of the origin al electronic FORMS. The originals can then be used to make additional electronic or pri nted copies of the blank FORMS. Signatures are not required on the electronic FORMS.
e. The Response shall include ample written evidence, in the form of technical specifications, cut/tear sheets, brochures, pictures, drawings, etc., to demonstrate that all specifications herein have been met and/or exceeded. f. The Response shall include, in any format desired, an overview of the Service Organization which will support Products sold under any H-GAC contract. The overview must include facility locations, phone numbers and Service Manager names, as well as the following:
- The procedure to be used by an End User requiring repairs. - Typical turn-around time on repairs.
- Service Department days and hours of operation.
- Number of qualified / factory trained service personnel normally on hand. - Description of the parts inventory on hand.
- Training services, facilities and personnel available. g. Responses shall be enclosed in a sealed package(s) addressed to the Houston-Galveston Area Council, Cooperative Purchasing. The following information shall be stated on the exterior of the package(s):
 Name and address of Offeror.
 Date and hour of public response opening.
 Bid/Proposal Invitation number.
 The statement: "SEALED BID/PROPOSAL, DO NOT OPEN IN MAIL ROOM".

H-GAC shall not be responsible for any Response not properly labeled. h. Submission of a COMPLETE Response by telegraphic or electronic transmission is not acceptable. However, Responses may be modified by telegraphic or electronic notice i f such notice is received prior to the deadline for submission.
i. Samples, when required, shall be submitted within the time spec ified and at no expense to H-GAC. If not destroyed or consumed during testing, samples will be returned upon request at Offeror's expense. j. Offeror shall provide firm contract pricing for all Products and Options being offered. k. If applicable, responses shall include copies of all current li censing which may be requ ired by the Texas Motor Vehicle Division for execution of sales pursuant to any contract with H-GAC. l. Due to the complexity of responses and to aid in evaluation, th e Response should contain ALL required information in tabbed sections as detailed below. Omission of any required FORM or information will be sufficient grounds for H-GAC to consider your response to be non-compliant. m. First Section:
 Form(s) A – Offeror Identification & Signatory: Identifies the offering party(ies), and should be completed by each party to the Response. If awarded, a contract will be executed with each.  Form B – Historically Underut ilized Business Enterprises: Used to collect information about disadvantaged and minority suppliers and subcontractors, and to commit Offeror to working with Participants toward their program goals.
 Form C – Response Checklist: Certification, and also an aid, to insure that all required i nformation has been included in your Response.

15.A

Revised: 04/16/18 Page 13 of 20

 Form W-9 – Request for Taxpayer Id entification Number and Certi fication: Should be completed by each party to the response.
 Form CIQ – Conflict Of Interest Questionnaire: Chapter 176 of the Texas Local Government Code requires vendors and consultants contracting or seeking to cont ract with H-GAC to file a Conflict of Interest Questionnaire (CIQ) if they have an employment or othe r business relationship with an H-GAC officer or an officer’s close family member. The required ques tionnaire is located at the Texas Ethics Commission website: http://www.ethic s.state.tx.us/whatsnew/conflict_forms.htm. It is Bidder's responsibility to download the form and furnish a completed copy with the Response.  Form 1295 – Certificate of Interested Parties – Must be filled out electronically with the Texas Ethics Commission’s online filing application, printed out, signed and provided from each entity that has submitted a Form A for this submission.
 House Bill HB 89 Verification Form – completed and signed and provided from each entity that has submitted a Form A for this submission.
 References, formatted as described elsewhere herein.
 Service Organization Document, formatted as described elsewhere herein.

Second Section:
 Form D – Offered Items Pricing: For Bids, contains the list of the Product Items covered by thi s Invitation. Select the items offered and fill in the price for each. (For RFPs, follow the instructions in Section B as this Form may or may not be used.)
 Form E – Published Options: Used to list and price all offered options. List, each on a se parate line, all upgrades, downgrades, optional equipment, features, accessories and services which you desire to sell thru the H-GAC contract, if awarded. Published catalogs/price sheets may be listed, along with the discount structure that will apply. (For RFPs, follow the instructions i n Section B as this Form may or may not be used.)
Third Section:
 Technical Specifications, Product Brochures, Tear Sheets, Cut Sheets, Strippers, etc. which clearly list and show all the standard features and capabilities of each Product Item offered on Form D.  Warranty Documentation, as described elsewhere herein, for all items offered.

Fourth Section:
 Copies of any applicable Texas MVD Licenses.
 Electronic Media, containing the complete response including all required FORMS, stored in a pouch or an envelope such that it will not fall out of the binder. (Required in 'Copy' only, not in 'Original'.) n. By submittal of Response, Offeror certifies to the best of its knowledge that all information is true and correct.

28. CLARIFICATION TO SPECIFICATIONS & REQUIREMENTS
a. If Offeror is in doubt as to the meaning of any item in this Invitation, a written request for clarification may be submitted to H-GAC up to fifteen (15) calendar days prior to the deadline for res ponse submission. H-GAC shall not be responsible for late delivery. Requests may be tr ansmitted by FAX or e-mail to the assigned Specification Specialist, and should clearly reference this Invitation number and the specific page and paragraph in question. If there are multiple questions, they should be stated separately and numbered. b. Any interpretation of Invitation documents, if made, will be by written Addendum duly issued. A copy of such Addendum will be mailed or delivered to each person officially on record as having been sent a copy of this Invitation. H-GAC will not be responsible for any other explanation or interpret ation of the Invitation documents made or given prior to the award of the contract. c. Any objections to the Invitation documents must be filed in wri ting with H-GAC on or before fifteen (15) calendar days prior to the deadline for submission of responses. d. P r o s p e c t i v e o f f e r o r s a r e a d v i s e d t h a t , a f t e r a d r a f t s p e c i f i c a tion has been issued, the Pre-Bid/Proposal Conference is the primary forum through which comments and suggestions may be offered for consideration by H-GAC prior to issuance of the final invitation and specifications.

15.A

Revised: 04/16/18 Page 14 of 20

e. All best efforts have been made to insure that the product/serv ice descriptions and associated specification information in Sections B & C are correct, and adequate time ha s been given to prospective Offerors to point out mistakes. However, if an error remains and is caught by Offeror before the scheduled bid/proposal opening, Offeror shall make note of the required correction in the Respo nse, and shall also notify H-GAC prior to the opening of responses.

29. INCONSISTENT INFORMATION
H-GAC review of responses supplied on H-GAC FORMS is a significant part of the evaluation process. Offeror shall state clearly all information required on the FORMS. Offeror's information supplied on the FORMS shall take precedence in the event any standard “boilerplate” type language included in Offeror's response is inconsistent with the information supplied by Offeror o n t h e H-GAC FORMS. In all cases, information on H-GAC's printed FORMS supplied as part of Offeror's response shall take precedence over information supplied on electronic media.

30. REJECTION OF RESPONSES
a. H-GAC may reject a response if:
 Offeror misstates or conceals any material fact in the Response, or if,  Offeror does not strictly conform to law or the requirements of this Invitation. b. H-GAC may reject any and all responses, and may reject any part of a response. c. H-GAC, at it's sole discretion, may also waive any formalities or irregularities in any respon se, or ask for corrected information except for pricing.
d. The following occurrences require disqualification of the bid/proposals:
 Unsigned or unauthorized signatures on bids/proposals;  Bids received after the date and time for opening
 Bids where prices are conditional on award of another bid or are subject to unlimited escalation e. H-GAC may refuse to award a contract t o or enter into a transaction w ith an apparent low bidder if that bidder is indebted to H-GAC.

31. WITHDRAWAL OR MODIFICATION OF RESPONSES
Once received by H-GAC, responses may be modified or withdrawn prior to the submissio n deadline only if the request to do so is in writing submitted by Offeror's authorized representative. Responses and requests for modification received after the submission deadline will not be accepted. Requests for response withdrawal received after the submission deadline will be accepted if the request to do so is in writing submitted by Offeror's authorized representative.

32. RESPONSE EVALUATION
For Bid Responses:
a. Section B will state whether the contract will be awarded to th e lowest responsible bidder or to the bidder who provides goods or services at the best value for H-GAC and its participants. b. If the contract will be awarded based on best value, Section B will state any relevant criteria which H-GAC will consider.
c. For each offered Product Item, H-GAC may use the offered price, prices for Required Options, and th e prices of selected common Published Options to determine the lowest responsible offer. d. Failure of Offeror to submit pricing for frequently purchased options and any H-GAC required options may cause response to be considered non-compliant at H-GAC’s sole discretion.

For Proposal Responses:
e. H-GAC will evaluate proposals as detailed in Section B. f. By submission of a Response Offe ror indicates acceptance of the evaluation technique, and recognizes and accepts that H-GAC may at it's sole discretion make subjective judgments during the evaluation process.

15.A

Revised: 04/16/18 Page 15 of 20

33. ORDER OF PRECEDENCE PRIOR TO CONTRACT AWARD
In the event of conflict between this document and any referenc es or documents cited herein, this document shall take precedence prior to contract award.

34. AWARD OF CONTRACT
a. H-GAC reserves the right to accept or reject any Product Item or opt ion offered. Additionally, all options included in Offeror's response and accepted by H-GAC are understood to be included in any contract. b. H-GAC shall award contract(s) for line items or groups of line items, at its sole discretion. c. With authority granted by the H-GAC Board of Directors, a written contract shall be presented to the successful Offeror(s) and shall be subject to acceptance by the successful Offeror(s) within forty-five (45) calendar days after presentation by H-GAC. If a contract is not executed within forty-five (45) calenda r days, H-GAC may rescind the contract offer and award a contract to the next Offeror in order of rank as determined by H-GAC. d. Delivery time and prompt payment discounts, including time allo wed for payment, may be considered in tie- breaking of offers which are judged by H-GAC to be equal in all other criteria. e. The contract shall include the following documents in the stated order of precedence:
1st The contract document signed by H-GAC and Offeror.
2nd This Invitation and all specifications referenced herein. 3rd Offeror's response to this Invitation.

35. PRO-FORMA CONTRACT
This Invitation includes a Pro-Forma (sample) Contract which su ccessful offerors will be expected to sign. The actual final contract will be the same or nearly the same as th e Pro-Forma. NOTE: Successful Offerors MAY NOT process any purchase orders until the contract documents have been executed and returned to H-GAC.

36. CONTRACT TERM
The contract shall be in effect t hroughout the period stated elsewhere in the contract documents, and thereafter until such time as any outstanding ord ers against the contract have b een fulfilled. The contract may be extended if deemed by H-GAC to be in the best interests of the Program, and subject to mutual agreement of the parties.

37. PERFORMANCE & PAYMENT BOND
H-GAC's contractual requirements DO NOT include a Performance & Paym ent Bond (PPB), and offered pricing should reflect this cost saving. However, Contractor must be prepared to offer a PPB to cover any specific order if so requested by End User. Contractor shall quote a price to End User for provision of any requested PPB, and agrees to furnish the PPB within ten business (10) days of receipt of End User's purchase order.

38. CHANGE ORDERS
End User s shall have the right to make additions by addenda for the pur pose of clarification or inclusion of additional specifications, qualifications, conditions, etc. An y such addenda shall be made in writing and agreed upon by Contractor and the End User agency prior to issuance of any Change Order. A copy of any s uch Change Order shall be furnished by Contractor to H-GAC.

39. DUPLICATION OF TERMS OR STATEMENTS
Where statements or terms are du plicated or are extremely simil ar, H-GAC and the End User reserve the right to use the statement or term most favorable to H-GAC and/or the End User.

40. PUBLICITY
H-GAC encourages contractors to "market" the Program, and can provide some information and artwork to be used in published promotional materials. However, any publicity or published material released by Contractor referencing the contract, whether in the form of a press releas e, brochure, photographic coverage, or verbal announcement, shall be issued only with prior review and approval by H-GAC.

15.A

Revised: 04/16/18 Page 16 of 20

41. TAXES
HGAC and End User participants are either units of government or qualified non-p rofit agencies, and are generally exempt from Federal and State sales, excise or use taxes. Offeror shall not include any such taxes in the Response.

Further, it shall be the responsibility of Contractor to determine the applicability of any taxes to a particular or der and act accordingly. Exemption certificates will be provided upon request.

42. DRUG FREE WORKPLACE
Contractor shall provide notice to its employees and sub-contractors, as required under the D rug-Free Workplace Act of 1988. A copy of Contractor's Drug-Free Workplace policy shall, on request, be furnished to any End User.

43. PRODUCT NOTICES & MAILINGS
H-GAC is NOT the owner of Products sold pursuant to this Invitation, but acts only in the capacity of purchasing agent. In that regard, Contractor accepts sole responsibility for i nsuring that notices and mailings, such as Safety Alerts, Safety Recall Notices and Customer Surveys, are sent directly to the End User of record.

44. HANDLING OF ORDERS & PAYMENTS
In general, orders and payments will be handled as described be low. More s pecific instructions a nd inf orm ation regarding handling of purchase orders and the Order Processing Charge may be provided after contract award.

Established procedures may be changed at any time by H-GAC as may be dictated by efficient business practice.

The particulars of any sale, e.g. specific products, pricing, d elivery, warranty, etc., will be in strict accordance with the terms and conditions of this Invitation and the specific contract awarded to Contractor. Beyond that:
a. For any particular procurement to be made under the provisions of an H-GAC contract, End User a n d Contractor will discuss requirements and agree as to what will be provided. b. Contractor will prepare a Contract Pricing Worksheet and provide it to End User. The Worksheet will list everything being purchased including the base bid item(s), all published and unpublished options and the delivery date. All pricing shall be per the current contract. c. End User will send a purchase document to Contractor, which Contractor will send H-GAC together with the Contract Pricing Worksheet. NOTE: Contractor agrees not to offer, agree to or accept from End User any terms or conditions that conflict with or contravene those in Contractor’s H-GAC contract, except for pricing discounts.
d. H-GAC will prepare an "Order Confirmation" and send it to End User a n d t o Contractor. T h e O r d e r Confirmation verifies that Contractor has a valid H-GAC contract and that the order is in compliance with the requirements of the H-GAC Cooperative Purchasing Program. Contractor will not ship any goods before receipt of both End User's purchase document and H-GAC's Order Confirmation. e. On notification that Contractor has received an order, H-GAC will invoice Contractor f o r t h e a p p l i c a b l e Order Processing Charge. NOTE: The Order Processing Charge is charged to Contractor, EXCEPT in the case of motor vehicles. For all sales of motor vehicles the Order Processing Charge is levied on the End User, collected by Contractor, and remitted to H-GAC by Contractor. f. Contractor will deliver products/services ordered, and will invoice End User for products/services accepted by End User. (See other Sub-Section herein dealing with Product Delivery. ) Contractor will not invoice before shipment has been made.
g. End User will pay Contractor for those products and/or services ordered which have been rec eived and accepted. Under no circumstances shall any check be made payab le to a representative or agent. Should a representative or agent submit an invoice to End User for any cost related to a purchase order issued to Contractor for products/services covered by an H-GAC contract, such invoice shall be forwarded to Contractor and Contractor will take action to correct the error. h. Upon delivery of any product/service by Contractor and acceptance by End User, Contractor shall remit to H-GAC the full amount of the applicable Order Processing Charge in a ccordance with the payment terms established in the H-GAC contract. Note, the Order Processing Charge is due whether or not Contractor has ever received an invoice from H-GAC. Sales executed based on the particulars of Contractor's H-GAC contract, without payment of the Order Processing Charge, may constitute fraud.

15.A

Revised: 04/16/18 Page 17 of 20

45. PRICE CHANGES
a. Any permanent increase or decrease in offered pricing for a base contract item or published option is considered to be a price change. Temporary increases in pricing by whatev er name (e.g. ‘surcharge’, ‘adjustment’, ‘equalization charge’, ‘compliance charge’, ‘recovery charge’, etc.), are also considered to be price changes. b. Except in the case of contracted published catalogs and price s heets, prices for Base Bid Items and Published Options a re e xpected t o be held firm for a m inim um of 90 days from the date an awarded Offeror signs the H-GAC contract. Thereafter, cha nges will be considered if acco mpanied by justifying documentation satisfactory to H-GAC. For pub lished catalogs and price sheets which are on an H-GAC contract, requests to amend the contract to reflect any new published catalog or pric e sheet may be submitted whenever the manufacturer publishes the new document. Any such request must include the new catalog or price sheet. c. If Contractor routinely offers discounted contract pricing, H-GAC may request Contractor to accept amended contract pricing equivalent to the routinely discounted pricing. d. No price change will be allowed unless it has been reviewed and approved by H-GAC in writing. Contractor must have received H-GAC's written approval of any change prior to charging the new price or using it in any quotation prepared for an End User.
e. Price change requests must be submitted to H-GAC in writing and must be received by H-GAC at least thirty (30) calendar days prior to the requested effective date of the change, and must state the time period for which the requested pricing will remain firm.
f. Price change requests shall include H-GAC Forms D and E, or whatever documentation was used to submit pricing in the original Response hereto, showing all affected i tems with current contract price, requested price, and percentage change shown clearly for each. This documentati on should be submitted in MSExcel format to facilitate analysis and updating of the website.
g. Price change requests MUST be supported with substantive documentation (e.g. manufacturer's price increase notices, copies of invoices from suppliers, etc.) showing that Contractor's actual costs have increased. The Producer Price Index (PPI) may be used as partial justification , subject to approval by H-GAC, but no price increase based solely on an increase in the PPI will be allowed. h. All Products shall, at time of sale, be equipped as may be required under any then current applicable local, state, and federal government requirements. If, during the course of any contract, changes are made to such government requirements which cause a manufacturer's costs of p roduction to increase, Contractor m a y increase Product pricing to the extent of Contractor’s actual cost increase. The increase must be substantiated with support documentation acceptable to H-GAC prior to taking effect. Modifications to a Product required to comply with such requirements which become effective after the date of any sale shall be the responsibility of the End-User.
i. In cases involving contract extensions exceeding sixty-one (61) days beyond the stated expiration date of the contract, Contractor may request a price change based on the same conditions as sta ted above. However the thirty (30) day prior notice is waived and H-GAC will consider the request immediately on receipt. j. H-GAC reserves the right to accep t or reject any price change r equest. Acceptance, if granted, will be in writing and the approved changes will become part of the contract.

46. CONTRACT ITEM CHANGES
a. If a manufacturer discontinues a contracted item, that item wil l automatically be considered to be deleted from the contract with no penalty to Contractor. However, H-GAC may at it's sole discretion elect to make a contract award to the next low offeror for the item, or take any other action deemed by H-GAC to be in the best interests of End Users, at its sole discretion.
b. If a manufacturer makes any chang e in a contracted item which d oes not affect the con tract price, Contractor shall advise H-GAC of the details. If the 'new' item is equal to or better than the originally contracted item, the 'new' item shall be approved as a replacement. Otherwise H-GAC may allow or reject the change, or take any other action deemed by H-GAC to be in the best interests of End Users, at its sole discretion. If the change is rejected there will be no penalty to Contractor.
c. If a manufacturer makes any kind of change in a contracted item which affects the cont ract price, Contractor shall advise H-GAC of the details. H-GAC may allow or reject the change at its sole discretion. If the change is rejected there will be no penalty to Contractor. However, H-GAC may elect to make a contract award to the next low offeror for the item, or take any other action deemed by H-GAC to be in the best interests of End Users, at its sole discretion.

15.A

Revised: 04/16/18 Page 18 of 20

d. In the case of specifically identified catalogs or price sheets which have been contracted as base bid items or as published options, routine published changes to products and pr icing shall be automatically incorporated into the contract. However, Contractor must still provide thirty (30) calendar days written notice an d an explanation of the changes to products and pricing. H-GAC will respond with written approval.

47. FORCE MAJEURE
If either party shall be wholly or partially prevented from the performance of any contractual obligation or duty by reason of or through strikes, stoppage of labor, riot, fire, fl ood, acts of war, insurrection, accident., order of any court, act of God, or specific cause reasonably beyond the part y's control and not attributable to its neglect or nonfeasance, in such event, the time for the performance of suc h obligation or duty shall be suspended until such disability to perform is removed. Determination of Force Majeure shall rest solely with H-GAC..

48. PERFORMANCE UNDER CONTRACT
H-GAC is committed to insuring that Contractor provides effective and efficien t service to all Participants i n the Cooperative Purchasing Program, an d expects that certain Perfor mance Conditions must be met. Failure to meet these conditions may result in contract termination. In that regard, Contractor shall:
a. Appoint a dedicated representative to be the contact person and focal point for all matters relating to End User quotations and orders. The representative shall have: A toll free phone number with voice mail; A fax number; A working e-mail address; and A postal address. b. Insure that the representative timely monitors all communication modes listed above, and promptly responds to communications from End Users and H-GAC in any of these modes. Phone calls will be promptly returned, in any event not later than the next business day. Acceptable failure will be due only to Force Majeure. c. Maintain sufficient qualified staff to promptly process all com munications from H-GAC or End Users, and to efficiently, effectively and accurately service all requirements of the contract. d. As may be requested by H-GAC, replace any staff members who are not providing the service a nd expertise deemed necessary by H-GAC for acceptable support of End Users. e. Properly prepare and provide to End User a Contract Pricing Worksheet, or a quotation in other format a s approved by H-GAC, for each and every order that is to be executed. f. Furnish, on request of H-GAC, reasonable data, forms and graphic material to be used in bro chures or other print media, or on H-GAC's website.
g. Allow access to H-GAC authorized personnel for inspection of operating facilities, a nd auditing of purchase orders during the contract period, and for a period extending thru the completion of any outstanding orders. Site inspection may be arranged not less than ten (10) calendar days prior, shall include the names of all participants, and shall be at no expense to Contractor.
h. Reporting Requirements:
 Contractor agrees to submit written quarterly reports to H-GAC detailing all transactions during the previous three month period. Such reports shall include, but are not limited to the following:
 End User name
 Product/Service purchased, including Product Code if applicable  End User Purchase Order Number
 Purchase Order Date
 Product/Service dollar amount
 HGACBuy Order Processing Charge amount
 Reports must be provided to H-GAC in MSExcel or other acceptable electronic format, and are due by the 30th day of the month following the applicable quarter being reported. i. Should Contractor default in providing Products or Services as required by this Invitation and the contract, recourse may be exercised thru cancellation of the contract and other legal remedies as may be appropriate.

49. CONTRACTOR ORIENTATION/TRAINING
H-GAC believes that Contractor's familiarity with the operational policies and requirements of the Cooperative Purchasing Program is a key factor in achieving End User satisfaction. In that regard, the Contact Person listed on Form A , or an alternate, shall be required to participate in an H-GAC vendor orientation/training as soon as

15.A

Revised: 04/16/18 Page 19 of 20

possible after contract award. In addition, any other of Contr actor's staff who will be involved in any way with the HGACBuy Program should participate in orientation. The orienta tion may be presented as a teleconference or webinar, or may be held in H-GAC's offices as may be determined by H-GAC and Contractor to be the most efficient and effective form of delivery.

50. LEGAL & CONTRACTUAL REMEDIES

RESOLUTION OF PROTESTED SOLICITATIONS AND AWARDS
Procedure
Any actual or prospective Offeror or Contractor who is aggrieved in connection with a purchase transaction may file a grievance. The griev ance may be filed at any phase of the procurement. In order for an above mentioned party to enter the grievance process, a written compl aint must be sent to the Chief Operations Officer (COO) of H-GAC by certified mail which identifies the following:

1. Name, mailing address and business phone number of the complainant.

2. Appropriate identification of the procurement being questioned.

3. A precise statement of reasons for the protest.

4. Supporting exhibits evidence or documents to substantiate any claims.

The grievance must be based on an alleged violation of H-GAC’s Procurement Procedures, a violation of State or Federal law (if applicable), o r a violation of applicable gr ant or contract agreements to which H-GAC is a party. Failure to receive a procurement award from H-GAC in and of itself does not constitute valid grievance. Upon receipt of grievance, the Chief Operations Officer will initiate the informal resolution process.

Expedited Resolution
The Procurement Officer or Depart mental Director responsible fo r the solicitation shall contact the complainant and all interested parties and attempt to resolve the allegations informally within ten (10) working days from date of complaint. If the allegations are successful ly resolved by mutual agreement, documentation will be forwarded to the Chief Operations Officer of the resolu tion with specifics on each point addressed in the original complaint.

If the Procurement Officer or Dep artmental Director is not succ essful in resolving the allegations, the complaint along with the comments will be forwarded to the Chie f Operations Officer immediately. The Chief Operations Officer will review all documentation. All interested parties will be given written notice of the date, time, and place of the hearing and an opportunity to present evidence. A written decision will be issued within five (5) working days after the hearing along with notice of appeal rights.

Appeals
The complainant may appeal the Chief Operations Officer’s decis ion by submitting a written appeal, within five (5) working days, to the Executive Director of H-GAC. The Executive Director, upon receipt of a written notice of appeal, shall contact the complainant and schedule a hearing within ten (10) working days. The Executive Director of H-GAC has the option of appointing a Hearing Officer to preside over the hearing. If appointed, the Hearing Officer shall conduct a hearing and forward a summary and recommended resolution to the Executive Director.

The decision reached by the Executive Director or his designee shall be final and conclusive. This decision will be forwarded to the complainant in writing within thirty (30) working days.

The Contractor may, if it elects to do so, app eal the final and conclusive decision of the Executive Director to a Court of competent jurisdiction.

RESOLUTION OF CONTRACT DISPUTES
Upon breach or default, H-GAC shall give the Contractor written notice of default. If t he default is not remedied, within a reasonable specified time from date of notification, t o the satisfaction and approval of H-GAC, default will be declared.

Upon breach of contract or default, H-GAC may exercise any and all of its rights afforded by law, includ ing but not limited to those referenced in the General Contract Provisions.

SOLICITATIONS OR AWARDS IN VIOLATION OF THE LAW
Contracts awarded in violation of the competitive process or ot herwise in violation of the law are voidable by H-GAC.