7 16. Notice. Any notices, requests, consents, claims, demands, waivers and other communications required or permitted to be given hereunder must be given in writing at the address of each P arty set forth below, or t o such other address as either P arty may substitute by written notice to the other in accordance with this Section 16 , by one of the following methods: hand delivery; registered, express, or certified mail, return receipt requested, postage prepaid; or nationally recognized private express courier. All such comm unications will be deemed to have been given: (i) when delivered by hand (with written confirmation of receipt); (ii) on the third (3 rd) calendar day after the
date mailed, by registered, express or certified mail; or (iii) when delivered by the addressee if sent by a nationally recognized private express courier.
GSFA: CUSTOMER:
Golden State Fire Apparatus Inc. To the address listed in the Product Proposal 7400 Reese Road
Sacramento, CA 95828
17. Contradictions. In the event of a conflict between the Agreement and any Change Order, or between Change Orders, the terms of the latest executed Change Order shall control.
18. Manufacturer’s Statement of Origin . It is agreed that the manufacturer’s statement of origin (“ MSO”) for the Product covered by the Agreement, if applicable, shall be retained and remain in the possession of GSFA per California Department of Vehicles (DMV) directive s. Notwithstanding the for egoing, GSFA shall provide Customer with the original MSO if the Customer is self- registering, and Customer shall comply with all good-faith Process of Duty and other DMV requirements applicable to the Product and retain its own MSO.
19. Assignment. The relationship of the Parties established under the Agreement is that of independent contractors and neither Party is a partner, employee, agent, or joint venturer of or with the other. Neither Party may assign its rights and obligations under the Agreement unless it has obtained the prior written approval of the other P arty.
20. Governing Law; Jurisdiction; Disputes. Without regard to any conflict of laws provisions, the Agreement is to be governed by and under the laws of the state of California. Prior to taking any legal action that may and/or can arise out of the Agreement, the Parties shall first attempt mediation with an agreed upon mediator. If the Parties cannot agree upon a mediator within thirty (30) calendar days of the submission of written notice of a dispute in accordance with Section 16 hereof, if any disputed matter remain unresolved within thirty (30) calendar days of the commencement of discussions, or if any party refuses to meet, then either party may submit any remaining disputes concerning and/or claim regarding the Agreement and/or the terms and conditions herein to the Superior Court, County of Sacramento (and the parties expressly consent to exclusive personal jurisdiction and venue before such court).
21. Entire Agreement; Amendments. The Agreement, including the Product Proposal, its exhibits and all valid Change Orders, is the exclusive agreement between the Parties regarding the subject matter contained herein and therein.
No change in, modi fication of, or revision of the Agreement shall be valid unless in writing and signed by duly authorized representatives of both Parties with authority to sign such amendments to the Agreement.
END OF STANDARD TERMS AND CONDITIONS
JROGHQVWDWHĆUHFRP
PRODUCT
SPECIFICATIONS
Exhibit “B”
3
Proposal Details Report
OptionCode
Type
Option
ProposalText
0766599
Boiler Plates, Tiller
Golden State Fire Apparatus, Inc.
is pleased to submit a proposal to
City of Turlock Fire
Department
for a
Pierce® Tractor-Drawn Aerial Ladder
per your request for quotation. The
following paragraphs will describe in detail the apparatus, construction methods, and equipment proposed. This proposal will indicate size, type, model and make of components parts and equipment, providing proof of compliance with each and every item (except where noted) in the departments advertised specifications.
PIERCE MANUFACTURING was founded in
1913
. Since then, we have been building bodies
with one philosophy, "BUILD THE FINEST". Our skilled craftsmen take pride in their work, which is reflected, in the final product. We have been building fire apparatus since the early "forties" giving Pierce Manufacturing over
110
years of experience in the fire apparatus market. Pierce Manufacturing has built and put into service more than
75,000
apparatus. Our Wisconsin facilities
have over
1.6 million total square feet of floor space situated on approximately 162
acres of land.
Our Bradenton, Florida facilities have
410,000
square feet of floor space situated on
approximately
35 acres of land.
Our beliefs in high ethical standards are carried through in all of our commitments and to everyone with whom we do business. Honesty, Integrity, Accountability and Citizenship are global tenets by which we all live and work. Consequently, we neither engage in, nor have we ever been convicted of price fixing, bid rigging, or collusion in any domestic or international fire apparatus market.
Pierce has only one brand of fire apparatus "Pierce", ensuring you are receiving top of the line product that meets your specification.
In accordance with the current edition of applicable NFPA standards, this proposal will specify whether the fire department, manufacturer, or apparatus dealership will provide required loose equipment.
Images and illustrative material in this proposal are as accurate as known at the time of publication but are subject to change without notice. Images and illustrative material are for reference only and may include optional equipment and accessories and may not include all standard equipment.
GENERAL DESIGN AND CONSTRUCTION
To control quality, ensure compatibility, and provide a single source for service and warranty, the custom cab, chassis, pump module and body will be entirely designed, assembled/welded and painted in Pierce owned manufacturing facilities. This includes, but not limited to the cab weldment, the pumphouse module assembly, the chassis assembly, the body and the electrical system.
QUALITY AND WORKMANSHIP
Pierce has set the pace for quality and workmanship in the fire apparatus field. Our tradition of building the highest quality units with craftsmen second to none has been the rule right from the beginning and we demonstrate that ongoing commitment by: Ensuring all steel welding follows American Welding Society D
1.1-2025
recommendations for structural steel welding. All aluminum welding follows American Welding society and ANSI D
1.2-2014
requirements for structural
welding of aluminum. All sheet metal welding follows American welding Society D
1.3 2018
requirements for structural welding of sheet metal. Our flux core arc welding uses Hobart FabCO Excel-Arc
71 , AWS A
5.20 , E
71 T
1 C/M and is performed to American Welding Society standards A
5.20 -E
70 T
1 . Furthermore, all employees classified as welders are tested and certified to meet the American welding Society codes upon hire. Pierce also employs an American Welding Society certified welding inspector in plant during working hours to monitor weld quality.
Pierce Manufacturing operates a Quality Management System under the requirements of ISO 9001
. A copy of the certificate of compliance is included with this proposal.
In addition to the Quality Management system, we also employ a Quality Achievement Supplier program to ensure the vendors and suppliers that we utilize meet the high standards we demand.
That is just part of our overall "Quality at the Source" program at Pierce.
To demonstrate the quality of our products and services, a list of at least two (
2 )
fire
departments/municipalities that have purchased vehicles for a second time is provided.
DELIVERY
The apparatus will be delivered under its own power to ensure proper break-in of all components while the apparatus is still under warranty.
A qualified delivery representative shall deliver the
apparatus and remain for a sufficient length of time to instruct personnel in proper operation, care and maintenance of the equipment delivered.
MANUAL AND SERVICE INFORMATION
At time of delivery, complete operation and maintenance manuals covering the apparatus will be provided. A permanent plate will be mounted in the driver's compartment specifying the quantity and type of fluids required including engine oil, engine coolant, transmission, pump transmission lubrication, pump primer and drive axle.
SAFETY VIDEO
At the time of delivery Pierce will also provide one (
1 )
39 -minute, professionally produced
apparatus safety video, in DVD format. A link to the video is also available at www.Pierceparts.com
. This video will address key safety considerations for personnel to follow when they are driving, operating, and maintaining the apparatus, including the following: vehicle pre-trip inspection, chassis operation, pump operation, aerial operation, and safety during maintenance.
PERFORMANCE TESTS
A road test will be conducted with the apparatus fully loaded and a continuous run of no less than ten (
10 ) miles. During that time the apparatus will show no loss of power nor will it overheat. The transmission drive shaft or shafts and the axles will run quietly and be free of abnormal vibration 3/16/2026
Customer:
Turlock Fire Department
Bid Number:
989
Representative
Young, Dewayne
Job Number:
Requirements Manager:
Organization:
Golden State Fire Apparatus, Inc
Description:
107' w/pump & Tank Ascendant
Chassis:
Velocity Tractor Chassis (Tiller), (Big Block), 2010
Body:
Aerial, Tiller, Alum Body
1 989
Bid #:
or noise. The apparatus when fully loaded will not have less than 25 percent nor more than
50 percent on the front axle, and not less than
50 percent nor more than
75 percent on the rear axle.
The apparatus will meet the current edition of applicable NFPA standards acceleration and braking requirements.
SERVICE AND WARRANTY SUPPORT
Pierce dealership support will be provided by
Golden State Emergency Vehicle Services
by
operating
a Pierce authorized service center. The service center will have factory-trained mechanics on staff versed in Pierce fire apparatus. The service facility will be located within seventy five (
75 ) miles
of the fire department.
In addition to the dealership, Pierce has service facilities located in both, Weyauwega, Wisconsin and Bradenton, Florida. Pierce also maintains a dedicated parts facility of over 100,000
square
feet in Appleton, Wisconsin. The parts facility stocks in excess of $15,000,000
in parts dedicated
to service and replacement parts. The parts facility employs a staff dedicated solely for the distribution and shipment of service and replacement parts.
Service parts for the apparatus being proposed can be found via Pierceparts.com which, is an interactive online tool that delivers information regarding your specific apparatus as well as the opportunity to register for training classes.
As a Pierce customer you have the ability to view the complete bill of materials for your specific apparatus, including assembly drawings, piece part drawings, and beneficial parts notations. You will also have the ability to search the complete Pierce item master through a parts search function which offers all Pierce SKU's and descriptions offered on all Pierce apparatus. Published component catalogs, which include proprietary systems along with an extensive operator's manual library is available for easy reference.
Pierce Manufacturing maintains a dedicated service and warranty staff of over 80 personnel
dedicated to customer support. Technical support is available 24/7/365
via the toll free hot line
and has four (
4 ) on staff EVTs that offer hands-on repair and maintenance training classes multiple times a year.
LIABILITY
The successful bidder will defend any and all suits and assume all liability for the use of any patented process including any device or article forming a part of the apparatus or any appliance furnished under the contract.
INSURANCE PROVIDED BY BIDDER
Commercial General Liability Insurance
The successful bidder will, during the performance of the contract and for three ( 3 ) years
following acceptance of the product, keep in force at least the following minimum limits of commercial general liability insurance:
Each Occurrence:
$1,000,000
Products/Completed Operations Aggregate:
$1,000,000
Personal and Advertising Injury:
$1,000,000
General Aggregate:
$2,000,000
Coverage will be written on a Commercial General Liability form. The policy will be written on an occurrence form and will include Contractual Liability coverage for bodily injury and property damage subject to the terms and conditions of the policy. The policy will include Owner as an additional insured when required by written contract.
Commercial Automobile Liability Insurance
The successful bidder will, during the performance of the contract, keep in force at least the following minimum limits of commercial automobile liability insurance and coverage will be written on a Commercial Automobile liability form:
Each Accident Combined Single Limit:
$1,000,000
Umbrella/Excess Liability Insurance
The successful bidder will, during the performance of the contract and for three ( 3 ) years
following acceptance of the product, keep in force at least the following minimum limits of umbrella liability insurance:
Aggregate:
$3,000,000
Each Occurrence:
$3,000,000
The umbrella policy will be written on an occurrence basis and at a minimum provide excess to the bidder's General Liability and Automobile Liability policies.
The required limits can be provided by one (
1 ) or more policies provided all other insurance
requirements are met.
Coverage will be provided by a carrier(s) rated A- or better by A.M. Best.
All policies will provide a
30 -day notice of cancellation to the named insured. The Certificate of Insurance will provide the following cancellation clause: Should any of the above described polices be cancelled before the expiration date thereof, notice will be delivered in accordance with the policy provisions.
Bidder agrees to furnish owner with a current Certificate of Insurance with the coverages listed above along with the bid. The certificate will show the purchaser as certificate holder.
INSURANCE PROVIDED BY MANUFACTURER
Product Liability Insurance
The manufacturer will, during the performance of the contract and for three ( 3 ) years following
acceptance of the product, keep in force at least the following minimum limits of Product Liability insurance:
Each Occurrence:
$1,000,000
Products/Completed Operations Aggregate:
$1,000,000
Coverage will be written on a Commercial General Liability form. The policy will be written on an occurrence form. The manufacturer's policy will include the owner as additional insured when required by written contract between the Owner and a Pierce authorized dealer.
Umbrella/Excess Liability Insurance
The manufacturer will, during the performance of the contract and for three ( 3 ) years following
2 989
Bid #:
acceptance of the product, keep in force at least the following minimum limits of umbrella liability insurance:
Each Occurrence:
$25,000,000
Aggregate:
$25,000,000
The umbrella policy will be written on an occurrence basis and provide excess to the manufacturer's General Liability/Products policies.
The required limits can be provided by one (
1 ) or more policies provided all other insurance
requirements are met.
Coverage will be provided by a carrier(s) rated A- or better by A.M. Best.
All policies will provide a
30 -day notice of cancellation to the named insured. The Certificate of Insurance will provide the following cancellation clause: Should any of the above described polices be cancelled before the expiration date thereof, notice will be delivered in accordance with the policy provisions.
Manufacturer agrees to furnish owner with a current Certificate of Insurance with the coverages listed above along with the bid. The certificate will show the purchaser as the certificate holder. 0018180
Single Source Compliance, Aerials
SINGLE SOURCE MANUFACTURER
Pierce Manufacturing, Inc. provides an integrated approach to the design and manufacture of our products that delivers superior apparatus and a dedicated support team. From our facilities, the chassis, cab weldment, cab, pump house (including the sheet metal enclosure, valve controls, piping and operators panel) body and aerial device will be entirely designed, tested, and hand assembled to the customer's exact specifications. The electrical system either hardwired or multiplexed, will be both designed and integrated by Pierce Manufacturing. The warranties relative to these major components (excluding component warranties such as engine, transmission, axles, pump, etc.) will be provided by Pierce as a single source manufacturer.
Pierce's single source solution adds value by providing a fully engineered product that offers durability, reliability, maintainability, performance, and a high level of quality. 0584456
Manufacture Location, Appleton,
Wisconsin
Your apparatus will be manufactured in Appleton, Wisconsin. 0584452
RFP Location: Appleton, Wisconsin
0588609
Vehicle Destination, US
0624924
SP
Unit Similar in Many Aspects
The apparatus being proposed will be designed and built to match the 43739
. However, some
variation may be necessary due to changes in our manufacturing processes or our product offering. Revisions in NFPA guidelines and/or other regulations may also affect our ability to match the previous unit.
0816491
Comply NFPA 1900 Changes
Effective Jan 1, 2024, With
Exceptions
NFPA
2024
STANDARDS
This unit will comply with the NFPA standards effective January 1 ,
2024
, except for fire
department directed exceptions. These exceptions will be set forth in the Statement of Exceptions.
Certification of slip resistance of all stepping, standing and walking surfaces will be supplied with delivery of the apparatus.
All horizontal surfaces designated as a standing or walking surface that are greater than
48.00 "
above the ground must be defined by a
1.00 " wide line along its outside perimeter. Perimeter markings and designated access paths to destination points will be identified on the customer approval print and are shown as approximate. Actual location(s) will be determined based on materials used and actual conditions at final build. Access paths may pass through hose storage areas and opening or removal of covers or restraints may be required. Access paths may require the operation of devices and equipment such as the aerial device or ladder rack.
A plate that is highly visible to the driver while seated will be provided. This plate will show the overall height, length, and gross vehicle weight rating.
The manufacturer will have programs in place for training, proficiency testing and performance for any staff involved with certifications.
An official of the company will designate, in writing, who is qualified to witness and certify test results.
0533349
Aerial Fire Apparatus
0588612
Vehicle Certification, Aerial w/Pump
3 989
Bid #:
0681278
Agency, Apparatus Certification,
Aerial w/Pump, U.L.
NFPA COMPLIANCY
Apparatus proposed by the bidder will meet the applicable requirements of the National Fire Protection Association (NFPA) as stated in current edition at time of contract execution. Fire department's specifications that differ from NFPA specifications will be indicated in the proposal as "non-NFPA".
INSPECTION CERTIFICATE
A third party inspection certificate for the aerial device will be furnished upon delivery of the aerial device. The certificate will be Underwriters Laboratories Inc. Type 1 and will indicate that the
aerial device has been inspected on the production line and after final assembly.
Visual structural inspections will be performed on all welds on both aluminum and steel ladders.
On critical weld areas, or on any suspected defective area, the following tests will be conducted:
Magnetic particle inspection will be conducted on steel aerials to assure the integrity of the weldments and to detect any flaws or weaknesses. Magnets will be placed on each side of the weld while iron powder is placed on the weld itself. The powder will detect any crack that may exist. This test will conform to ASTM E
709
and be performed prior to assembly of the aerial
device.
A liquid penetrant test will be conducted on aluminum aerials to assure the integrity of the weldments and to detect any flaws or weaknesses. This test will conform to ASTM E 165
and be
performed prior to assembly of the aerial device.
Ultrasonic inspection will be conducted on all aerials to detect any flaws in pins, bolts and other critical mounting components.
In addition to the tests above, functional tests, load tests, and stability tests will be performed on all aerials. These tests will determine any unusual deflection, noise, vibration, or instability characteristics of the unit.
PUMP TEST
The pump will be tested, approved and certified by Underwriter's Laboratory at the manufacturer's expense. The test results and the pump manufacturer's certification of hydrostatic test; the engine manufacturer's certified brake horsepower curve; and the manufacturer's record of pump construction details will be forwarded to the Fire Department.
GENERATOR TEST
If the unit has a generator, the generator will be tested, approved, and certified by Underwriters Laboratories at the manufacturer's expense. The test results will be provided to the Fire Department at the time of delivery.
BREATHING AIR TEST
If the unit has breathing air, Pierce Manufacturing will draw an air sample from the air system and certify that the air quality meets the requirements of NFPA 1989
,
Standard on
Breathing Air
Quality for Fire and Emergency Services Respiratory Protection. 0816495
Certification, Vehicle Inspection
Program, NFPA 1900
VEHICLE INSPECTION PROGRAM CERTIFICATION
To assure the vehicle is built to current NFPA
1900
standards, the apparatus, in its entirety, will
be third-party, independent, audit-certified through Underwriters Laboratory (UL) that it is built and complies to all applicable standards in the current edition. The certification includes: all design, production, operational, and performance testing of not only the apparatus, but those components that are installed on the apparatus.
A placard will be affixed in the driver's side area stating the third party agency, the date, the standard and the certificate number of the whole vehicle audit. 4 989
Bid #:
0536644
Customer Service Website
AFTERMARKET SUPPORT WEBSITE
Pierceparts.com will provide
Pierce authorized dealer
access to comprehensive information
pertaining to the maintenance and service of their customer's apparatus. This tool will provide the Pierce authorized dealer the ability to service and support their customers to the best of their ability with factory support at their fingertips.
Pierceparts.com is also accessible to the end user through the guest login. Limited access is available and vehicle specific parts information accessible by entering a specific VIN number. All end users should see their local authorized Pierce dealer for additional support and service.
The website will consist of the following screens at the dealer level:
My Fleet Screen
The My Fleet screen will provide access to truck detail information on the major components of the vehicle, warranty information, available vehicle photographs, vehicle drawings, sales options, applicable vehicle software downloads, etc.
Parts Screens
The Parts screens will provide parts look-up capability of Pierce Manufacturing sourced items, with the aid of digital photographs, part drawings and assembly drawings. The parts search application will permit the searching of parts by item description or function group (major system category). The parts application will provide the ability to submit electronically a parts order, parts quote, or parts return request directly to Pierce Manufacturing for processing.
Warranty Screen
The Warranty screens will provide dealers the ability to submit electronically warranty claims directly to Pierce Manufacturing for reimbursement.
My Reports Screens
The My Reports screens will provide access to multiple dealer reports to allow the dealership to maintain communication with the customer on the status of orders, claims, and phone contacts.
Technical Support Screens
The Technical Support screens will provide access to all currently published Operation and Maintenance and Service Publications. Access to Pierce Manufacturing Service Bulletins and Work Instructions, containing information on current service topics and recommendations will be provided.
Training
The Training screens will provide access to upcoming training classes offered by Pierce Manufacturing along with interactive electronic learning modules (Operators Guides) covering the operation of major vehicle components will be provided. Access to training manuals used in Pierce Manufacturing training classes will be provided.
About Pierce
Access to customer service articles, corporate news, quarterly newsletters, and key contacts within the Customer Service Department will be provided. The current Customer Service Policy and Procedure Manual, detailing the operation of the Customer Service group will also be accessible.
0620362
Consortium, HGAC
0537375
Unit of Measure, US Gallons
0030006
Bid Bond Not Requested
BID BOND NOT REQUESTED
A bid bond will not be included. If requested, the following will apply:
All bidders will provide a bid bond as security for the bid in the form of a 5 percent bid bond to
accompany their bid. This bid bond will be issued by a Surety Company who is listed on the U.S.
Treasury Departments list of acceptable sureties as published in Department Circular 570
. The
bid bond will be issued by an authorized representative of the Surety Company and will be accompanied by a certified power of attorney dated on or before the date of bid. The bid bond will include language, which assures that the bidder/principal will give a bond or bonds as may be specified in the bidding or contract documents, with good and sufficient surety for the faithful performance of the contract, including the Basic One (
1 ) Year Limited Warranty, and for the
prompt payment of labor and material furnished in the prosecution of the contract.
Notwithstanding any document or assertion to the contrary, any surety bond related to the sale of a vehicle will apply only to the Basic One (
1 ) Year Limited Warranty for such vehicle. Any surety
bond related to the sale of a vehicle will not apply to any other warranties that are included within this bid (OEM or otherwise) or to the warranties (if any) of any third party of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. In the event of any contradiction or inconsistency between this provision and any other document or assertion, this provision will prevail.
5 989
Bid #:
0816571
Performance Bond, 100% with 25%
Warranty Bond, 1 Yr, and Payment
Bond, PPI Terms
PERFORMANCE BOND,
1 YEAR
The successful bidder will furnish a Performance and Payment bond (Bond) equal to 100
percent
of the total contract amount within
30 days of the notice of award. Such Bond will be in a form acceptable to the Owner and issued by a surety company included within the Department of Treasury's Listing of Approved Sureties (Department Circular 570
) with a minimum A.M. Best
Financial Strength Rating of A and Size Category of XV. In the event of a bond issued by a surety of a lesser Size Category, a minimum Financial Strength rating of A+ is required.
Bidder and Bidder's surety agree that the Bond issued hereunder, whether expressly stated or not, also includes the surety's guarantee of the vehicle manufacturer's Basic One ( 1 ) Year Limited
Warranty period included within this proposal. Owner agrees that the penal amount of this bond will be simultaneously amended to
25 percent of the total contract amount upon satisfactory acceptance and delivery of the vehicle(s) included herein. Notwithstanding anything contained within this contract to the contrary, the surety's liability for any warranties of any type will not exceed one (
1 ) year from the date of such satisfactory acceptance and delivery, or the actual Basic One (
1 ) Year Limited Warranty period, whichever is shorter.
Due to global supply chain constraints, any delivery date contained herein is a good faith estimate as of the date of this order/contract, and merely an approximation based on current information. Delivery updates will be made available, and a final firm delivery date will be provided as soon as possible.
If the Producer Price Index of Components for Manufacturing [www.bls.gov Series ID:
WPUID
6112
] ("PPI") has increased at a compounded annual growth rate of
5.0%
or more
between the month Pierce accepts the order ("Order Month") and a month 14 months prior to the
then predicted Ready For Pickup date ("Evaluation Month"), then pricing may be updated in an amount equal to the increase in PPI over
5.0%
for each year or fractional year between the Order
Month and the Evaluation Month.
The seller will document any such updated price for the customer's approval before proceeding and provide an option to cancel the order.
0000007
Approval Drawing
APPROVAL DRAWING
A drawing of the proposed apparatus will be prepared and provided to the purchaser for approval before construction begins. The Pierce sales representative will also be provided with a copy of the same drawing. The finalized and approved drawing will become part of the contract documents. This drawing will indicate the chassis make and model, location of the lights, siren, horns, compartments, major components, etc.
A "revised" approval drawing of the apparatus will be prepared and submitted by Pierce to the purchaser showing any changes made to the approval drawing. 0517327
Drawing, As Built, At Delivery a
Revised Print w/ Changes
FINAL DRAWING
There will be a revised drawing of the truck with all the changes made during production provided at pickup.
0682087
Drawing, Compartment Layout, Tiller
DRAWING, COMPARTMENT LAYOUT
A basic drawing will be provided for the interior body compartments. This drawing will be provided for graphic representation only and will include such things as shelves, trays, reels, dividers, air control panels, air bottle storage bins, poly boxes, etc. 0002928
Electrical Diagrams
ELECTRICAL WIRING DIAGRAMS
Two (
2 ) electrical wiring diagrams, prepared for the model of chassis and body, will be provided. 0564218
Velocity Tractor Chassis (Tiller), (Big
Block), 2010
VELOCITY CHASSIS
The Pierce Velocity® chassis provided will be a new, tilt-type custom fire apparatus. The chassis will be manufactured in the apparatus body builder's facility, eliminating any split responsibility.
The chassis will be designed and manufactured for heavy duty service, with adequate strength and capacity for the intended load to be sustained and the type of service required. 0021007
Maximum Overall Height
MAXIMUM OVERALL HEIGHT
The maximum overall height of the apparatus will be
140.00
" (
11 '-
8.00 ")
.
0021010
Maximum Overall Length
MAXIMUM OVERALL LENGTH
The maximum overall length of the apparatus will be
732.00
” (
61 '-
0 ")
.
0523786
Angle of Approach
ANGLE OF APPROACH
The angle of approach will be
15.90 degrees. This will be effective with the truck in a loaded
state.
0523787
Angle of Departure
ANGLE OF DEPARTURE
The angle of departure will be
11.9 degrees. This will be effective with the truck in a loaded
state.
0000110
Wheelbase
WHEELBASE
The wheelbase of the vehicle will be
173.00
"
.
6 989
Bid #:
0000070
GVW Rating
GVW RATING
The gross vehicle weight rating will be
76,600
pounds
.
0000203
Frame Rails, 13.38 x 3.50 x .375,
Qtm/AXT/Imp/Vel
FRAME
The chassis frame will be built with two (
2 ) steel channels bolted to five (
5 ) cross members or
more, depending on other options of the apparatus. The side rails will have a
13.38 " tall web over
the front and mid sections of the chassis, with a continuous smooth taper to
10.75 " over the rear
axle. Each rail will have a section modulus of
25.992
cubic inches and a resisting bending
moment (rbm) of
3,119,040
in-lb over the critical regions of the frame assembly, with a section modulus of
18.96 cubic inches with an rbm of
2,275,200
in-lb over the rear axle. The frame rails
will be constructed of
120,000
psi yield strength heat-treated
0.38 " thick steel with
3.50 " wide
flanges.
0020018
Frame Liner Not Req'd
0508849
Axle, Front, Oshkosh TAK-4, Non
Drive, 22,800 lb, Imp/Vel
FRONT NON DRIVE AXLE
The Oshkosh TAK-
4 ® front axle will be of the independent suspension design with a ground rating of
22,800
lb.
Upper and lower control arms will be used on each side of the axle. Upper control arm castings will be made of
100,000
-psi yield strength
8630
steel and the lower control arm casting will be
made of
55,000
-psi yield ductile iron.
The center cross members and side plates will be constructed out of 80,000
-psi yield strength
steel.
Each control arm will be mounted to the center section using elastomer bushings. These rubber bushings will rotate on low friction plain bearings and be lubricated for life. Each bushing will also have a flange end to absorb longitudinal impact loads, reducing noise and vibrations.
There will be nine (
9 ) grease fittings supplied, one (
1 ) on each control arm pivot and one (
1 ) on
the steering gear extension.
The upper control arm will be shorter than the lower arm so that wheel end geometry provides positive camber when deflected below rated load and negative camber above rated load.
Camber at load will be
0 degrees for optimum tire life.
The ball joint bearing will be of low friction design and be maintenance free.
Toe links that are adjustable for alignment of the wheel to the center of the chassis will be provided.
The wheel ends will have little to no bump steer when the chassis encounters a hole or obstacle.
The steering linkage will provide proper steering angles for the inside and outside wheel, based on the vehicle wheelbase.
The axle will have a turning angle of up to
45 degrees.
0010427
Suspension, Front TAK-4, 22,800 lb,
Qtm/AXT/Imp/Vel/Enf/SFR
FRONT SUSPENSION
Front Oshkosh TAK-
4 ™
independent suspension will be provided with a minimum ground rating of
22,800
lb.
The independent suspension system will be designed to provide maximum ride comfort. The design will allow the vehicle to travel at highway speeds over improved road surfaces and at moderate speeds over rough terrain with minimal transfer of road shock and vibration to the vehicle's crew compartment.
Each wheel will have torsion bar type spring. In addition, each front wheel end will also have energy absorbing jounce bumpers to prevent bottoming of the suspension.
The suspension design will be such that there is at least
10.00 " of total wheel travel and a
minimum of
3.75 " before suspension bottoms.
The torsion bar anchor lock system allows for simple lean adjustments, without the use of shims.
One can adjust for a lean within
15 minutes per side. Anchor adjustment design is such that it allows for ride height adjustment on each side.
The independent suspension was put through a durability test that simulated 140,000
miles of
inner city driving.
0087572
Shock Absorbers, KONI, TAK-4,
Qtm/AXT/Imp/Vel/Enf
FRONT SHOCK ABSORBERS
KONI heavy-duty telescoping shock absorbers will be provided on the front suspension. 0000322
Oil Seals, Front Axle
FRONT OIL SEALS
Oil seals with viewing window will be provided on the front axle. 0899288
Tires, Front, Goodyear, Armor MAX
MSA, 425/65R22.50, 20 ply, Fire
Service Speed
FRONT TIRES
Front tires will be Goodyear
425/65
R
22.50 radials,
20 ply Armor MAX MSA, rated for
22,800
lb
maximum axle load and
75 mph maximum speed.
0019618
Wheels, Front, Alcoa, 22.50" x
13.00", Aluminum, Hub Pilot
The tires will be mounted on Alcoa 22.50" x 13.00" polished aluminum disc type wheels with a ten (10) stud, 11.25" bolt circle.
7 989
Bid #:
0000310
Request for Turning Radius Report
TURNING RADIUS REPORT
A turning radius analysis of the custom Pierce chassis that we are proposing will be included with this proposal. This analysis will provide information on the inside turning radius, the outside turning radius, the curb to curb turning radius, and the wall to wall turning radius. 0530467
Axle, Rear, Meritor RS30-185, 31,000
lb, Imp/Vel
REAR AXLE
The rear axle will be a Meritor
™,
Model RS-
30-185
, with a capacity of
31,000
lb.
0818717
Top Speed of Vehicle, 65 MPH/104
KPH, Non-NFPA/ULC 2024
TOP SPEED OF VEHICLE
NFPA
1900
and ULC
515
,
2024
edition requires limits on the top speed of vehicles. NFPA
7.16.1 requires that the maximum top speed of fire apparatus with a GVWR over 33,000
lb will not
exceed either
68 mph or the manufacturer's maximum fire service speed rating for the tires installed on the apparatus, whichever is lower. NFPA
7.16.2 requires that if the combined water
tank and foam agent tank on the fire apparatus exceed
1250
gallons or the GVWR of the vehicle
is over
50,000
lb, the maximum top speed of the apparatus will not exceed either 60 mph or the
manufacturer's maximum fire service speed rating for the tires installed on the apparatus, whichever is lower. It is the intention of the standard to improve safety by limiting the speed of all apparatus to
68 mph, and tankers or heavy apparatus to
60 mph. By requesting an exception to
this requirement, the purchasing authority is consciously choosing to operate their apparatus at speeds above the limits designated as safe speeds by the NFPA Technical Committee on Fire Department Apparatus.
The top speed of the apparatus as manufactured exceeds the NFPA requirements. Per fire department specification of a top speed that exceeds NFPA requirements, the apparatus will be non-compliant to NFPA
1900
and ULC
515
standards at time of contract execution.
The rear tires being specified have a top speed limit of 65 mph /
104
kph from the tire
manufacturer.
0555352
Suspen, Rear, Hendrickson FMX 312
EX, Air Ride, 31,000 lb
REAR SUSPENSION
Rear suspension will be a Hendrickson FMX
312
EX, air ride with a ground rating of
31,000
lb.
The suspension will have the following features:
Heavy-duty shock absorbers to protect air springs from overextension Heavy-duty torque rods and bushings
Premium, heavy-duty rubber bushings require no lubrication Integrated stabilizer design results in greater stability Low spring rate air springs for excellent ride quality
Dual height control valves to maintain level vehicle from side to side 0000485
Oil Seals, Rear Axle
REAR OIL SEALS
Oil seals will be provided on the rear axle(s).
0539392
Plug, Rear Axle Drain, Magnetic
REAR AXLE DRAIN PLUG
The rear axle drain plug will be magnetic.
0798161
Tires, Rear, Goodyear, G751 MSA,
315/80R22.50, LRL, Single, Fire
Service Speed R
REAR TIRES
Rear tires will be four (
4 ) Goodyear
315/80
R
22.50 radials with load range L, all position, G
751
MSA , rated for
33,080
lb maximum axle load and
75 mph maximum speed.
0889830
Wheels, Rear, Alcoa, 22.50" x 9.00",
Aluminum, Hub Pilot, Single, 315 GY
The tires will be mounted on Alcoa 22.50" x 9.00" polished aluminum disc wheels with a ten (10) stud 11.25" bolt circle.
0568081
Tire Balancing, Counteract Beads
TIRE BALANCE
All tires will be balanced with Counteract balancing beads. The beads will be inserted into the tire and eliminate the need for wheel weights.
0620570
Tire Pressure Monitoring,
RealWheels, AirSecure, Valve Cap,
Single Axle
TIRE PRESSURE MANAGEMENT
There will be a RealWheels LED AirSecure
™
tire alert pressure management system provided,
that will monitor each tire's pressure. A sensor will be provided on the valve stem of each tire for a total of
eight (
8 ) tires
.
The sensor will calibrate to the tire pressure when installed on the valve stem for pressures between
10 and
200
psi. The sensor will activate an integral battery operated LED when the pressure of that tire drops
5 to
8 psi.
Removing the cap from the sensor will indicate the functionality of the sensor and battery. If the sensor and battery are in working condition, the LED will immediately start to flash. 0801932
Lug Nut, Covers, Stainless Steel
LUG NUT COVERS
Stainless steel lug nut covers will be installed on all lug nuts. 8 989
Bid #:
0003245
Axle Hub Covers w/center hole, S/S,
Front Axle
FRONT HUB COVERS
Stainless steel hub covers will be provided on the front axle. An oil level viewing window will be provided.
0003246
Axle Hub Covers w/center hole, S/S,
Tiller Axle
HUB COVERS (Tiller Axle)
Stainless steel hub covers will be provided on the tiller trailer axle. An oil level viewing window will be provided.
0001960
Axle Hub Covers, Rear, S/S, High
Hat (Pair)
REAR HUB COVERS
A pair of stainless steel high hat hub covers will be provided on rear axle hubs. 0002045
Mud Flap, Front and Rear, Pierce
Logo
MUD FLAPS
Mud flaps with a Pierce logo will be installed behind the front and rear wheels. 0020257
Mud Flap, Tiller Trailer, Pierce Logo
MUD FLAPS
Mud flaps will be installed behind the tiller trailer wheels of the apparatus. 0767032
Valve, Extension Stabilizer System,
Single Axle
VALVE STEM STABILIZER SYSTEM
A valve stem stabilizer system will be provided on the rear inside tires. 0617577
Chocks, Wheel, Worden HWG- SB,
Super Gripper
WHEEL CHOCKS
There will be
two (
2 ) pairs
of Worden Safety Products, Model HWG-SB, wheel chocks provided.
Heavy Duty, large molded aluminum wheel chock with solid bottom, natural cast aluminum finish. 0646364
Mounting Brackets, Chocks, Worden
Safety, Model U815T
Wheel Chock Brackets
There will be
two (
2 ) pairs
of Worden Safety, Model U
815
T, mounting wheel chock brackets
provided. The brackets will be mounted
TBD
.
0822289
ABS/ATC Wabco Brake System,
Single Axle, Tiller, NFPA 1900/ULC
ANTI-LOCK BRAKE SYSTEM
The vehicle will be equipped with a Wabco tractor
4 S
4 M and tiller tractor
2 S
2 M anti-lock braking
system. The ABS will provide a four (
4 ) channel anti-lock braking control on both the front, rear tractor axle, and a two (
2 ) channel system on the tiller axle. It will be a digitally controlled system that utilizes microprocessor technology to control the anti-lock braking system. Each wheel will be monitored by the system. When any particular wheel begins to lockup, a signal will be sent to the control unit. This control unit then will reduce the braking of that wheel for a fraction of a second and then reapply the brake. This anti-lock brake system will eliminate the lockup of any wheel thus helping to prevent the apparatus from skidding out of control.
Automatic Traction Control
An anti-slip feature will be included with the ABS. The Automatic Traction Control will be used for traction in poor road and weather conditions. The Automatic Traction Control will act as an electronic differential lock which will not allow a driving wheel to spin, thereby supplying traction at all times. The ABS electronic control unit (ECU) will work with the engine ECU, sharing information concerning wheel slip. Engine ECU will use information to control engine speed, allowing only as much throttle application as required for the available traction, regardless of how much the driver is asking for. An "Off-road traction" switch will be provided on the instrument panel. Activation of the switch will allow additional tire slip to let the truck climb out and get on top of deep snow or mud.
0030185
Brakes, Knorr/Bendix 17", Disc,
Front, TAK-4
BRAKES
The service brake system will be full air type.
The front brakes will be Knorr/Bendix disc type with a
17.00 " ventilated rotor for improved
stopping distance.
The brake system will be certified, third party inspected, for improved stopping distance. 0803729
Brakes, Meritor, Cam, Rear, 16.50 x
8.63" No Dust Shield
The rear brakes will be Meritor
™ 16.50"
x 8.63" cam operated with automatic slack adjusters.
Dust shields cannot be provided.
0020784
Air Compressor, Brake,
Cummins/Wabco 18.7 CFM
BRAKE SYSTEM AIR COMPRESSOR
The air compressor will be a Cummins/WABCO with
18.7 cubic feet per minute output.
9 989
Bid #:
0000785
Brake Reservoirs, Three
BRAKE SYSTEM
The brake system will include:
Bendix® dual brake treadle valve
Heated automatic moisture ejector on air dryer
Total air system capacity of
4,362
cubic inches
Two (
2 ) air pressure gauges with a red warning light and an audible alarm, that activates when air pressure falls below
60 psi
Spring set parking brake system
Parking brake operated by a push-pull style control valve A parking "brake on" indicator light on instrument panel Park brake relay/inversion and anti-compounding valve, in conjunction with a double check valve system, with an automatic spring brake application at
40 psi
A pressure protection valve to prevent all air operated accessories from drawing air from the air system when the system pressure drops below
80 psi (
550
kPa)
1/4
turn drain valve on each air tank
The air tank will be primed and painted to meet a minimum 750
hour salt spray test.
The air tanks will be painted
same as frame color
.
To reduce the effects of corrosion, the air tank will be mounted with stainless steel brackets. 0568012
Air Dryer, Wabco System Saver
1200, Heater, 2010
BRAKE SYSTEM AIR DRYER
The air dryer will be WABCO System Saver
1200
with spin-on coalescing filter cartridge and
100
watt heater.
0000790
Brake Lines, Nylon
BRAKE LINES
Color-coded nylon brake lines will be provided. The lines will be wrapped in a heat protective loom in the chassis areas that are subject to excessive heat. 0813346
Inlet/Outlet, Air, w/Disconnect Fitting,
1/4 Turn Valve, Location
AIR INLET/OUTLET
One (
1 ) air inlet/outlet
will be installed with the female coupling located
in the driver side lower
step well of cab
. This system will tie into the "wet" tank of the brake system and include a check valve in the inlet line and an
85 psi pressure protection valve in the outlet line. The air outlet will be controlled by a
1/4
turn valve.
A mating male fitting will be provided with the loose equipment.
The air inlet will allow a shoreline air hose to be connected to the vehicle. This will allow station air to be supplied to the brake system of the vehicle to insure constant air pressure. 0792009
SP
Outlet, Air, with shut off valve
Recessed, Fill In Blank Feature
AIR OUTLET
One (
1 ) air outlet
will be installed with a female coupling and shut off valve, located recessed P
8 Rear compartment bulkhead, centered up and down, close to the roll up door. . This system will
tie into the "wet" tank of the brake system and include an 85 psi pressure protection valve in the
outlet line to prevent the brake system from losing all air.
A mating male fitting will be provided with the loose equipment. 0656908
All Wheel Lock-up, Single Prk Brk
Control
ALL WHEEL LOCK-UP
An all wheel lock-up system will be installed which applies air to the front brakes and uses the spring brake at the rear.
Front brakes will apply with the standard parking brake control. 0658952
Air Tank, Additional for Extra Air Horn
Capacity, Velocity Tiller
ADDITIONAL AIR TANK
An additional air tank with
1,454
cubic inch displacement will be provided to increase the capacity of the air system. This tank will be dedicated for air horn use.
The air tank will be primed and painted to meet a minimum 750
hour salt spray test. To reduce
the effects of corrosion, the air tank will be mounted with stainless steel brackets.
The air tank(s) will be painted
same as frame color
.
The output flow of the engine air compressor varies with engine RPM. Full compressor output is only achieved at governed engine speed. Engine speed may be limited by generators, pumps and other PTO driven options.
0642617
Air Line, S/S Braid, Air Governor To
Air Dryer
AIR LINE
The air line from the air compressor governor to the air dryer will be stainless steel braid. 0607839
Fittings, Compression Type, Entire
Apparatus, Single Axle Tiller
COMPRESSION FITTINGS ONLY
Any nylon hose on the apparatus that is pneumatic will be plumbed with compression type fittings where applicable.
10 989
Bid #:
0808499
Engine, Cummins X15, 565 hp, 1850
lb-ft, W/OBD, EPA 2027, Velocity
ENGINE
The chassis will be powered by an electronically controlled engine as described below:
Make:
Cummins®
Model:
X
15 Power:
565
hp at
1700
rpm
Torque:
1850
lb-ft at
1150
rpm
Governed Speed:
2100
rpm
Emissions Level:
EPA
2027
Fuel:
Diesel
Cylinders:
Six (
6 )
Displacement:
912
cubic inches (
14.9 L)
Starter:
Delco
39 MT+
™
Fuel Filters:
Frame mounted spin-on style filter from Cummins®.
The engine will include On-board diagnostics (OBD), which provides self diagnostic and reporting. The system will give the owner or repair technician access to state of health information for various vehicle sub systems. The system will monitor vehicle systems, engine and after treatment. The system will illuminate a malfunction indicator light on the dash console if a problem is detected.
The engine will be filled with FA-
4 10
W
30 oil as required by Cummins.
0811409
Not Required, Engine Contingency
Adjustment
0730808
Filters, Remote Mounted, Oil, Fuel,
X15, VEL/AXT/Enf
REMOTE MOUNTED ENGINE FILTERS
The engine fuel and oil filters will be remote mounted for ease of maintenance. 0001244
High Idle w/Electronic Engine,
Custom
HIGH IDLE
A high idle switch will be provided, inside the cab, on the instrument panel, that will automatically maintain a preset engine rpm. A switch will be installed, at the cab instrument panel, for activation/deactivation.
The high idle will be operational only when the parking brake is on and the truck transmission is in neutral. A green indicator light will be provided, adjacent to the switch. The light will illuminate when the above conditions are met. The light will be labeled "OK to Engage High Idle." 0687994
Engine Brake, Jacobs Compression
Brake, Cummins Engine
ENGINE BRAKE
A Jacobs® engine brake is to be installed with the controls located on the instrument panel within easy reach of the driver.
The driver will be able to turn the engine brake system on/off and have a high, medium and low
setting
.
The engine brake will activate when the system is on and the throttle is released.
The high setting of the brake application will activate and work simultaneously with the variable geometry turbo (VGT) provided on the engine.
The engine brake will be installed in such a manner that when the engine brake is slowing the vehicle the brake lights are activated.
The ABS system will automatically disengage the auxiliary braking device, when required. 0552334
Clutch, Fan, Air Actuated, Horton
Drive Master
CLUTCH FAN
A Horton® fan clutch will be provided. The fan clutch will be automatic when the pump transmission is in "Road" position, and fully engaged in "Pump" position. 0123135
Air Intake, w/Ember separator,
Imp/Vel
ENGINE AIR INTAKE
An air intake with an ember separator (to prevent road dirt, burning embers, and recirculating hot air from entering the engine) will be mounted at the front of the apparatus, on the passenger side of the engine. The ember separator will be mounted in the air intake with flame retardant, roto- molded polyethylene housing. It will be easily accessible by the hinged access panel at the front of the vehicle.
11 989
Bid #:
0814375
Exhaust System, Horizontal, Right
Side
EXHAUST SYSTEM
The exhaust system will be stainless steel from the turbo to the engine's aftertreatment device.
The exhaust system will include an aftertreatment device to meet current EPA standards. An insulation wrap will be provided on all exhaust pipe between the turbo and the aftertreatment device to minimize the transfer of heat to the cab.
The exhaust will terminate horizontally ahead of the right side rear wheels and will be flush with
the body rub rail
. The exhaust pipes will be
aluminized steel
.
There will be
an aluminized steel exhaust diffuser reduced to
5.00 " in the center to accommodate
the fire department's air recovery system
with
a standard straight tip on the end
provided to
reduce the temperature of the exhaust as it exits. Heat deflector shields will be provided to isolate chassis and body components from the heat of the tailpipe diffuser. 0787999
Radiator, Impel/Velocity
RADIATOR
The radiator and the complete cooling system will meet or exceed the current edition of applicable NFPA and engine manufacturer cooling system standards.
For maximum corrosion resistance and cooling performance, the entire radiator core will be constructed using long life aluminum alloy. The core will be made of aluminum fins, having a serpentine design, brazed to aluminum tubes. The tubes will be brazed to aluminum headers.
The radiator core will have a minimum frontal area of
1434
square inches. Supply tank made of
glass-reinforced nylon and a return tank of cast aluminum alloy will be crimped on to the core assembly using header tabs and a compression gasket to complete the radiator core assembly.
The radiator will be compatible with commercial antifreeze solutions.
There will be a full steel frame around the entire radiator core assembly. The radiator core assembly will be isolated within the steel frame by rubber inserts to enhance cooling system durability and reliability. The radiator will be mounted in such a manner as to prevent the development of leaks caused by twisting or straining when the apparatus operates over uneven ground. The radiator assembly will be isolated from the chassis frame rails with rubber isolators.
The radiator assembly will include an integral de-aeration tank permanently mounted to the top of the radiator framework, with a readily accessible remote-mounted overflow tank. For visual coolant level inspection, the radiator will have a built-in sight glass. The radiator will be equipped with a
15 psi pressure relief cap.
A drain port will be located at the lowest point of the cooling system and/or the bottom of the radiator to permit complete flushing of the coolant from the system.
A heavy-duty fan will draw in fresh, cool air through the radiator. Shields or baffles will be provided to prevent recirculation of hot air to the inlet side of the radiator. 0511425
Cooling Hoses, Rubber
COOLANT LINES
Gates, or Goodyear, rubber hose will be used for all engine coolant lines installed by the chassis manufacturer.
Hose clamps will be stainless steel "constant torque type" to prevent coolant leakage. They will react to temperature changes in the cooling system and expand or contract accordingly while maintaining a constant clamping pressure on the hose.
0828627
Fuel Tank, 50 Gallon, Dual Fill,
Tractor Chassis
FUEL TANK
A
50 gallon fuel tank will be provided and mounted at rear of chassis. The tank will be constructed of
12 -gauge, hot rolled steel. It will be equipped with swash partitions and a vent. To eliminate the effects of corrosion, the fuel tank will be mounted with stainless steel straps.
A
0.75 " drain plug will be provided in a low point of the tank for drainage.
Duel fills will be located on the chassis on the vertical portion of the fender skirting area. The inlets will be covered with a hinged, spring loaded, stainless steel door that is marked "Ultra Low Sulfur - Diesel Fuel Only.".
A
0.50 " diameter vent will be provided running from top of tank to just below fuel fill inlet.
The tank will meet all FHWA
393.67
requirements, including a fill capacity of
95 percent of tank
volume.
0001128
Lines, Fuel, Wire Braided, Reusable
Fittings
All fuel lines will be of the wire braided type. Reusable fittings will be provided. 0763582
DEF Tank, 4.5 Gallon, DS Fill,
Forward of Rear Axle, Tiller
DIESEL EXHAUST FLUID TANK
A
4.5 gallon diesel exhaust fluid (DEF) tank will be provided and mounted in the driver's side body forward of the rear axle.
A
0.50 " drain plug will be provided in a low point of the tank for drainage.
A fill inlet will be located on the driver's side of the body and be covered with a hinged polished
stainless steel
door that is marked "Diesel Exhaust Fluid Only".
The tank will meet the engine manufacturers requirement for 10 percent expansion space in the
event of tank freezing.
The tank will include an integrated heater unit that utilizes engine coolant to thaw the DEF in the event of freezing.
0723716
Fuel Priming Pump, Electronic,
Automatic, Cummins, No Swt Req'd
FUEL PRIMING PUMP
A Cummins automatic electronic fuel priming pump will be integrated as part of the engine. 0582243
Shutoff Valves, Fuel Line @ Primary
Filter, Cummins
FUEL SHUTOFF
A fuel line shutoff valve will be installed on both the inlet and outlet of the primary fuel filter. 12 989
Bid #:
0553019
Cooler, Engine Fuel, Imp/Vel,
SFR/Enf
FUEL COOLER
An air to fuel cooler will be installed in the engine fuel return line. 0567427
Fuel Lines, Extended, PAL/Tiller
FUEL LINES
The fuel lines for the fuel tank will be approximately
4 ' longer than standard. This will allow the
lines to be coiled above the fuel tank and aid in an easier removal of the fuel tank if necessary. 0578959
Fuel/Water Separator, Racor Inline
FUEL SEPARATOR
The engine will be equipped with a Racor in-line spin-on fuel and water separator in addition to the engine fuel filters.
0887546
Trans, Allison 6th Gen, 4000 EVS P,
w/Prognostics, Imp/Vel/SFR/Enf
TRANSMISSION
An Allison
6 th generation, Model EVS
4000
P, electronic, torque converting, automatic
transmission will be provided.
The transmission will be equipped with prognostics to monitor oil life, filter life, and transmission health. A wrench icon on the shift selector's digital display will indicate when service is due.
Two (
2 ) PTO openings will be located on left side and top of converter housing (positions 8 o'clock and
1 o'clock).
A transmission temperature gauge with an amber light and buzzer will be installed on the cab instrument panel.
0625331
Transmission, Shifter, 6-Spd, Push
Button, 4000 EVS
TRANSMISSION SHIFTER
A six (
6 )-speed push button shift module will be mounted to right of driver on console. Shift position indicator will be indirectly lit for after dark operation.
The transmission ratio will be:
1 st
3.51 to
1.00 2
nd
1.91 to
1.00 3
rd
1.43 to
1.00 4
th
1.00 to
1.00 5
th
0.75 to
1.00 6
th
0.64 to
1.00 R
4.80 to
1.00 0684459
Transmission Oil Cooler, Modine,
External
TRANSMISSION COOLER
A Modine plate and fin transmission oil cooler will be provided using engine coolant to control the transmission oil temperature.
0801876
Fluid, 4000 Series Trans, Allison
Approved TES-668 Synthetic, IPOS,
Custom
TRANSMISSION FLUID
The transmission will be provided with TranSynd, or other Allison approved TES- 668
heavy duty
synthetic transmission fluid.
0001375
Driveline, Spicer 1810
DRIVELINE
Drivelines will be a heavy-duty metal tube and be equipped with Spicer® 1810
universal joints.
The shafts will be dynamically balanced before installation.
A splined slip joint will be provided in each driveshaft where the driveline design requires it. The slip joint will be coated with Glidecoat® or equivalent. 0669988
Steering, Sheppard M110 w/Tilt,
TAK-4, Eaton Pump, w/Cooler
STEERING
Dual Sheppard, Model M
110
, steering gears, with integral heavy-duty power steering, will be provided. For reduced system temperatures, the power steering will incorporate an air to oil cooler and an Eaton, Model VN
20 , hydraulic pump with integral pressure and flow control. All power steering lines will have wire braded lines with crimped fittings.
A tilt and telescopic steering column will be provided to improve fit for a broader range of driver configurations.
0001544
Not Required, Steering Assist
Cylinder on Front Axle
0509230
Steering Wheel, 4 Spoke without
Controls
STEERING WHEEL
The steering wheel will be
18.00 " in diameter, have tilting and telescoping capabilities, and a 4 -
spoke design.
13 989
Bid #:
0690274
Logo/Emblem, on Dash
LOGO AND CUSTOMER DESIGNATION ON DASH
The dash panel will have an emblem containing the Pierce logo and customer name. The emblem will have three (
3 ) rows of text for the customer's department name. There will be a maximum of eight (
8 ) characters in the first row,
11 characters in the second row and
11 characters in the third row.
The first row of text will be:
TURLOCK
The second row of text will be:
FIRE
The third row of text will be:
DEPARTMENT
0612391
Oil, Steering Gear, 15W40, CK-4
STEERING GEAR OIL
15 W
40 , CK-
4 oil will be provided for the steering gear.
0790541
Bumper, 10" Ext, Fab, .25" Steel,
Painted, 12" H, Imp/Vel
BUMPER
A
1 -piece bumper manufactured from
0.25 " formed steel with a
0.38 " bend radius will be
provided. The bumper will be a minimum of
12.00 " high with a
1.50 " top and bottom flange and
extend
10.00 " from the face of the cab. The bumper will be
102.00
" wide with
45 degree corners.
To provide adequate support strength, the bumper will be mounted directly to the front of the C channel frame. The frame will be a bolted modular extension frame constructed of 50,000
psi
tensile steel.
The bumper will be metal finished and painted to match the lower job color of the apparatus.
Gravel Pan
A gravel pan, constructed of bright aluminum treadplate, will be furnished between the bumper and the cab face. The pan will be properly supported from the underside to prevent flexing and vibration.
Documentation will be provided, upon request to show that the options selected have been engineered for fit up and approval for this modular bumper extension. A chart will be provided to indicate the option locations and will include but not be limited to the following options: air horns, mechanical sirens, speakers, hose trays with hose capacities, winches, lights, discharge and suction connections.
0510226
Lift & Tow Package, Imp/Vel, AXT
LIFT AND TOW MOUNTS
Mounted to the frame extension will be lift and tow mounts. The lift and tow mounts will be designed and positioned to adapt to certain tow truck lift systems.
The lift and tow mounts with eyes will be painted the same color as the frame. 0698960
Coating, Top Flange, Front Bumper,
Outside Exterior, UL-LX Coating,
Black
FRONT BUMPER UL-LX COATING
Protective black UL-LX® coating will be provided on the outside exterior of the top front bumper flange. It will not be sprayed on the underside of the flange.
The lining will be properly installed by an authorized UL-LX dealer. 14 989
Bid #:
0647245
Cab, Velocity FR, 6000
CAB
The Velocity cab will be designed specifically for the fire service and will be manufactured by Pierce Manufacturing.
To provide quality at the source and single source customer support, the cab will be built by the apparatus manufacturer in a facility located on the manufacturer's premises.
For reasons of structural integrity and enhanced occupant protection, the cab will be of heavy duty design, constructed to the following minimal standards.
The cab will have
12 main vertical structural members located in the A-pillar (front cab corner posts), B-pillar (side center posts), C-pillar (rear corner posts) and rear wall areas. The A-pillar will be constructed of
0.25 " heavy wall extrusions joined by a solid A
356
-T
6 aluminum joint
casting. The B-pillar and C-pillar will also be constructed from
0.25 " heavy wall extrusions. The
rear wall will be constructed of two (
2 )
4.00 " x
2.00 " outer aluminum extrusions and two (
2 )
3.00 "
x
2.00 " inner aluminum extrusions. All main vertical structural members will run from the floor to
7.50 " x
3.50 " x
0.125
" thick roof extrusions to provide a cage-like structure with the A-pillar and roof extrusions being welded into a
0.75 " thick corner casting at each of the front corners of the roof assembly.
The front of the cab will be constructed of a
0.25 " thick firewall, covered with a
0.125
" front skin
(for a total thickness of
0.38 "), and reinforced with
24.50 " wide x
10.00 " deep x
0.50 " thick
supports on each side of the engine tunnel. The cross-cab support will be welded to the A-pillar,
0.25 " firewall, and engine tunnel, on the left and right sides.
The cab floors will be constructed of
0.1875
" thick aluminum plate and reinforced at the firewall
with an additional
0.25 " thick cross-floor support providing a total thickness of
0.44 " of structural
material at the front floor area. The front floor area will also be supported with three ( 3 )
0.50 "
plates bolted together that also provides the mounting point for the cab lift. This tubing will run from the front of the cab to the
0.1875
" thick engine tunnel, creating the structure to support the forces created when lifting the cab.
The cab will be a full-tilt style. A
3 -point cab mount system with rubber isolators will improve ride quality by isolating chassis vibrations from the cab.
The crew cab will be a totally enclosed design with the interior area completely open to improve visibility and verbal communication between the occupants.
The centerline of front axle to the rear of the cab will be
60.00 " long.
The overall height (from the cab roof to the ground) will be approximately 102.00
". The overall
height listed will be calculated based on a truck configuration with the lowest suspension weight ratings, the smallest diameter tires for the suspension, no water weight, no loose equipment weight, and no personnel weight. Larger tires, wheels, and suspension will increase the overall height listed.
The cab will have an interior width of not less than
93.50 ". The driver and passenger seating
positions will have a minimum
24.00 " clear width at knee level.
To reduce injuries to occupants in the seated positions, proper head clearance will be provided.
The floor-to-ceiling height inside the forward cab will be no less than
60.25 ". The floor-to-ceiling
height inside the crew cab will be no less than
52.95 " in the center position and
58.75 " in the
outboard positions.
The crew cab will measure a minimum of
47.50 " from the rear wall to the backside of the engine tunnel (knee level) for optimal occupant legroom.
FENDER LINERS
Full-circular, aluminum inner fender liners in the wheel wells will be provided.
PANORAMIC WINDSHIELD
A one (
1 )-piece, safety glass windshield with more than
2,802
square inches of clear viewing area
will be provided. The windshield will be full width and will provide the occupants with a panoramic view. The windshield will consist of three (
3 ) layers: the outer light, the middle safety laminate, and the inner light. The
0.114
" thick outer light layer will provide superior chip resistance. The middle safety laminate layer will prevent the windshield glass pieces from detaching in the event of breakage. The inner light will provide yet another chip resistant layer. The cab windshield will be bonded to the aluminum windshield frame using a urethane adhesive. A custom frit pattern will be applied on the outside perimeter of the windshield for a finished automotive appearance.
WINDSHIELD WIPERS
Three (
3 ) electric windshield wipers with a washer, in conformance with FMVSS and SAE requirements, will be provided. The wiper blades will be
21.65 " long and together will clear a
minimum of
1,783
square inches of the windshield for maximum visibility in inclement weather.
The windshield washer fluid reservoir will be located at the front of the vehicle and be accessible through the access hood for simple maintenance.
FAST SERVICE ACCESS FRONT TILT HOOD
A full-width access hood will be provided for convenient access to engine coolant, steering fluid, wiper fluid, cab lift controls, headlight power modules, and ember separator. The hood will also provide complete access to the windshield wiper motor and components. The hood will be contoured to provide a sleek, automotive appearance. The hood will be constructed of two ( 2 )
fiberglass panels bonded together and will include reinforcing ribs for structural integrity. The hood will include air cylinders to hold the hood in open and closed positions, and a heavy duty latch system that will meet FMVSS
113
(Hood Latch System). The spring-loaded hood latch will
be located at the center of the hood with a double-action release lever located behind the Pierce logo. The two (
2 )-step release requires the lever first be pulled to the driver side until the hood releases from the first latch (primary latch) then to the passenger side to fully release the hood (secondary latch).
0724207
Engine Tunnel, X12-15, MX13, Foil
Insulation w/Mech Fasteners,
Velocity FR
ENGINE TUNNEL
To provide structural strength, the engine tunnel sidewalls will be constructed of
0.50 " aluminum
plate that is welded to both the
0.25 " firewall and
0.38 " heavy wall extrusion under the crew cab
floor. To maximize occupant space, the top edges will be tapered.
The engine tunnel will be insulated for protection from heat and sound. Perforated foil faced insulation will be over a
1.00 " thick closed cell foam affixed with pressure sensitive adhesive and further secured with mechanical fasteners. Thermal rating for this insulation will be - 40 degrees
Fahrenheit to
300
degrees Fahrenheit. The noise insulation keeps the dBA level within the limits stated in the current edition of applicable NFPA standards. 15 989
Bid #:
0818272
Cab Insulation, Extreme Climate, Foil
Insulation, Impel/Velocity
INSULATION PACKAGE
All insulation utilized in the cab construction will be provided for extreme climate temperatures.
The insulation will be provided in the following areas:
Engine tunnel
Cab and crew cab floors
Cab and crew cab step wells
Cab and crew cab doors
Cab roof
Cab and crew cab walls
0677478
Rear Wall, Exterior, Cab, Aluminum
Treadplate
CAB REAR WALL EXTERIOR COVERING
The exterior surface of the rear wall of the cab will be overlaid with bright aluminum treadplate except for areas that are not typically visible when the cab is lowered. 0897669
SP
Cab Lift, Elec/Hyd, w/Manual
Override, Batt Swtich, Imp/Vel
CAB LIFT
A hydraulic cab lift system will be provided, consisting of an electric-powered hydraulic pump, fluid reservoir, dual lift cylinders, remote cab lift controls and all necessary hoses and valves. The hydraulic pump will have a backup manual override, for use in the event of an electrical failure.
The cab lift controls will be located at the driver side front of the cab, easily accessible under the full width front access hood. The controls will include a permanently mounted raise/lower switch.
For enhanced visibility during cab tilt operations, a remote control tether with on/off switch will be supplied on a coiled cord that will extend from
2.00 ' (coiled) to
6.00 ' (extended).
The cab will be capable of tilting
42 degrees and
80 degrees with crane assist to accommodate
engine maintenance and removal. The cab pivots will be located
46.00 " apart to provide stability
while tilting the cab.
The rear of the cab will be locked down by a two (
2 )-point, automatic, hydraulic, double hook
mechanism that fully engages after the cab has been lowered (self-locking). The dual
2.25 "
diameter hydraulic cylinders will be equipped with a velocity fuse that protects the cab from accidentally descending when the cab is in the tilt position.
For increased safety, a redundant mechanical stay arm will be provided that must be manually put in place on the driver side between the chassis and cab frame when cab is in the raised position. This device will be manually stowed to its original position before the cab can be lowered.
Cab Lift Interlock
The cab lift safety system will be interlocked to the parking brake. The cab tilt mechanism will be active only when the parking brake is set and the battery switch is in the on position. If the parking brake is released, the cab tilt mechanism will be disabled. 0751126
Grille, Bright Finished, Painted Mesh
Screen, Front of Cab, Impel/Velocity
GRILLE
An aluminum mesh grille screen, inserted behind a formed bright finished grille surround, will be provided on the front center of the cab, and will serve as an air intake to the radiator. The mesh screen will be
painted black
#101
.
0002224
Scuffplates, S/S At Cab Door Jambs,
4-Door Cab
DOOR JAMB SCUFFPLATES
All cab door jambs will be furnished with a
1.00 "
polished stainless steel
scuffplate, mounted on
the striker side of the jamb.
0012226
Scuffplates, S/S Corner Guard,
Polished, Rear Cab Corners
SCUFFPLATES, REAR CAB CORNER GUARDS
Both rear cab corners will be furnished with a full height, polished stainless steel corner guard scuffplate. The guard will extend
1.00 " from the corner to protect paint from damage when pulling items (such as booster hose) around the cab.
0527032
Trim, S/S Band, Across Cab Face,
Rect Lights, Velocity
FRONT CAB TRIM
A band of
22 gauge
polished stainless steel
trim will be installed across the front of the cab, from door hinge to door hinge. The trim band will be centered on the head lights and applied with two (
2 )-sided tape. A
0.625
" self adhesive trim strip will be applied around the perimeter of the trim band.
There will be
polished stainless steel corner covers
provided over the painted cab corner where
the cab turn signals are located.
0015440
No Chrome Molding, On side of cab
0783530
SP
Mirrors, Ramco, 8000PCHR, All
Heated/Remote, w/Convex, Dr Mnt,
Add Wiring
MIRRORS
One (
1 ) Ramco, Model
8000
-PCHR, polished aluminum mirror will be mounted on each of the cab doors. The mirrors will be
9.25 " wide x
13.50 " high with a convex section.
The mirror head
will have a highly polished aluminum finish.
The flat glass in each mirror will be heated and adjustable, with remote controls that are convenient to the driver.
The convex section in each mirror will be heated and adjustable, with remote controls that are convenient to the driver.
For ease of maintenance each mirror will be provided with an additional
6.00 " of wiring for
service needs.
16 989
Bid #:
0651321
Door, Full Height, Velocity FR 4-Door
Cab, Level Roof
CAB DOORS
To enhance entry and egress to the cab, the forward cab doors will be a minimum of
43.59 " wide
x
76.46 " high. The crew cab doors will be located on the sides of the cab and will be constructed in the same manner as the forward cab doors. The crew cab doors will measure a minimum of
37.87 " wide x
76.46 " high.
The forward cab and crew cab doors will be constructed of extruded aluminum with a nominal material thickness of
0.125
". The exterior door skins will be constructed from
0.090
" aluminum.
The forward cab door windows will include a
7.50 " high x
10.00 " wide drop area at the front to
enhance visibility.
A customized, vertical, pull-down type door handle will be provided on the exterior of each cab door. The finish of the door handle will be
chrome/black
. The exterior handle will be designed
specifically for the fire service to prevent accidental activation, and will provide
4.00 " wide x
2.00 "
deep hand clearance for ease of use with heavy gloved hands.
Each door will also be provided with an interior flush, open style paddle handle that will be readily operable from fore and aft positions, and be designed to prevent accidental activation. The interior handles will provide
4.00 " wide x
1.25 " deep hand clearance for ease of use with heavy
gloved hands.
The cab doors will be provided with both interior (rotary knob) and exterior (keyed) locks exceeding FMVSS standards. The keys will be Model
751
. The locks will be capable of activating
when the doors are open or closed. The doors will remain locked if locks are activated when the doors are opened, then closed.
A heavy duty, stainless steel, piano-type hinge with a
0.38 " pin and
11 gauge leaf will be provided
on all cab doors. There will be double automotive-type rubber seals around the perimeter of the door framing and door edges to ensure a weather-tight fit.
A chrome grab handle will be provided on the inside of each cab and crew cab door.
A red webbed grab handle will be installed on the crew cab door stop strap. The grab handles will be securely mounted.
The cab steps at each cab door location will be located inside the cab doors to protect the steps from weather elements.
0655511
Door Panel, Brushed Stainless Steel,
Impel/Velocity 4-Door Cab
Door Panels
The inner cab door panels will be constructed out of brushed stainless steel. The cab door panels will be removable.
0795698
Storage Pockets w/ Elastic Cover,
Recessed, Locations, Impel/Velocity
FR
RECESSED POCKET WITH ELASTIC COVER
To provide organized storage (clutter control) in the cab for miscellaneous equipment, the cab interior will be provided with recessed storage pockets. The pockets will be
5.63 " wide x
2.00 "
high and
6.24 ". The pockets will be provided with a perforated elastic material cover to secure the equipment in the pocket. The pockets will be installed
RS Lower dash, Location
14 on IP drawing.
Match
38759
, as indicated on the instrument panel layout.
0825970
SP
Controls, Electric Windows, All Cab
Doors, Impel/Velocity FR, Pnl 8
ELECTRIC WINDOW CONTROLS
Each cab entry door will be equipped with an electrically operated tempered glass window. A window control panel will located on the door panel within easy reach of the respective occupant.
Each switch will allow intermittent or auto down operation for ease of use. Auto down operation will be actuated by holding the window down switch for approximately 1 second. The switch panel
number
8 will contain a control switch for each cab and crew cab door's window. All other door control panels will contain a single switch to operate the window within that door.
The window switches will be connected directly to the battery power. This allows the windows to be raised and lowered when the battery switch is in the off position. 0662776
Electric Door Locks, Cab Doors,
Conceal Switch Feature, Imp/Vel
ELECTRIC CAB DOOR LOCKS
The front driver and passenger doors will have a door lock master switch (custom designed rotary lock knob) built into the interior door latch that will control all front and rear side exit door locks.
Each rear cab door will have its own lock control. Each door will have a keyed exterior lock mechanism built into the door handle assembly.
There will be one (
1 ) concealed switch located
Switch to be located on LS pump panel switch
panel.
.
The lock system will include two (
2 ) key FOBs that allow for keyless entry into the vehicle. The key FOB system will use code hopping technology for high security and be FCC part 15 compliant.
0555485
Steps, 4-Door Full Tilt Cab, Imp/Vel
CAB STEPS
The forward cab and crew cab access steps will be a full size two ( 2 ) step design to provide
largest possible stepping surfaces for safe ingress and egress. The bottom steps will be designed with a grip pattern punched into bright aluminum treadplate material to provide support, slip resistance, and drainage. The bottom steps will be a bolt-in design to minimize repair costs should they need to be replaced. The forward cab steps will be a minimum
31.00 " wide, and the
crew cab steps will be
24.25 " wide with an
8.00 " minimum depth. The inside cab steps will not
exceed
18.00 " in height and be limited to two (
2 ) steps.
0770200
Handrail, Exterior, Hansen, Knurled,
Alum, LED Backlit, 4-Door Cab
CAB EXTERIOR HANDRAILS
A Hansen knurled aluminum handrail will be provided adjacent to each cab and crew cab door opening to assist during cab ingress and egress. Each handrail will be provided with white
LED
lights. The lights will be activated
when the parking brake is applied
. The LED lights may be load
managed.
17 989
Bid #:
0892637
Lights, Cab & Crw Cab Acs Stps,
P25, LED w/Bezel, 1Lt Per Step
STEP LIGHTS
There will be four (
4 ) white P
25 LED step lights provided. The lights will be installed at each cab and crew cab door, one (
1 ) per step. The lights will be located in the driver side front doorstep, driver side crew cab doorstep, passenger side front doorstep and passenger side crew cab doorstep.
In order to ensure exceptional illumination, each light will provide a minimum of 25 foot-candles
(fc) covering an entire
15.00 " x
15.00 " square placed
10.00 " below the light and a minimum of
1.5 fc covering an entire
30.00 " x
30.00 " square at the same
10.00 " distance below the light.
The light(s) will have a
chrome housing
.
The lights will be activated when the adjacent door is opened. 0002140
Fenders, S/S on Cab
FENDER CROWNS
Stainless steel fender crowns will be installed at the cab wheel openings. 0825060
Tractor 5th Wheel and Fenders,
Single
FIFTH WHEEL
The fifth wheel will be designed to allow the tiller trailer to pivot fore and aft and be rotated. The fifth wheel will also be capable of full operation up to a 14 degree break over angle.
A fill and a gauge port will be provided on the top of the trailer goose neck for maintenance.
LOCKOUT
A fifth wheel lockout system will be provided to limit motion during aerial operations.
The fifth wheel lockout system, when activated, will prevent movement between the upper and lower plates of the fifth wheel assembly.
In the normal road travel condition, the cylinder mounted solenoid valves will be open and will allow transfer of oil between the front and rear pair of cylinders.
When the stabilizers are in their proper supporting position and as the aerial leaves the boom support, the solenoid valves will close.
The closed valves will allow no oil to be transferred and the fifth wheel assembly will become rigid.
There will be a cylinder lockout indicator located in the cab.
FENDER PANELS
The chassis behind the cab will be assembled with fender panels over the wheels.
The fender panels will be fabricated of
0.125
"-
5052
aluminum with a
38,000
psi tensile strength.
Fender design will be provided for prevention of rust pockets and ease of maintenance.
FENDER CROWNS
Stainless steel
fender crowns will be provided around the rear wheel openings.
A rubber welting will be provided between the body and the crown to seal the seam and restrict moisture from entering.
A dielectric barrier will be provided between the fender crown fasteners (screws) and the fender sheet metal to prevent corrosion.
WALKWAY
The area over the frame rails between the cab and fifth wheel will be covered with aluminum treadplate to serve as a walkway area.
The walkway area will be properly reinforced with a steel substructure attached to the frame rails.
RUNNING BOARDS
Running boards will be installed on each side directly behind the cab for access to the walkway area behind the cab and the turntable.
The running boards will be covered with aluminum treadplate. 0592071
No Windows, Side of Crew Cab,
Vel/Imp
0568605
Not Required, Interior Trim, No Cab
Side Windows
0509286
Not Required, Windows Rear of Crew
Cab, Imp/Vel
0558334
Not Required, Trim, Cab Rear
Windows, No Rear Windows
0887710
Window Coatings, Solar Film,
Cab/Crew Cab
WINDOW COATINGS
All cab and crew cab windows will have solar window film applied. The solar film will block UV rays and excess heat while not impacting the visibility or clarity of the window. 0816708
Tubes, Alum, Pike Pole Storage
PIKE POLE STORAGE
Aluminum tubing will be used for the storage of
three (
3 )
pike pole(s) with
1.38 " notch, to
accommodate a New York style pike pole
. The tubing will be located
Transverse Hydraulic
Reservoir compartment behind cab
. The tubing will be accessed from the
Two (
2 ) with RS
deployment of Tool One (
1 ) with LS deployment of tool
.
The size and brand of the pike poles stored will be
New York Hook - RH
9 - Pry end
.
0123686
Drip Rail, Cab Roof,
Impel/Velocity/Velocity SLT
CAB ROOF DRIP RAIL
For enhanced protection from inclement weather, a drip rail will be furnished on the sides of the cab. The drip rail will be constructed of bright polished extruded aluminum, and be bonded to the sides of the cab. The drip rail will extend the full length of the cab roof. 18 989
Bid #:
0199285
Visor, Exterior, Vel/Imp
EXTERIOR VISOR
The exterior sun visor will be a painted composite to match the job color. The five ( 5 ) forward
facing marker lights will be mounted to the visor.
0644019
Holder, Cup, 4" Diameter x 4" High x
1" Slit on Side, Matting, Alum, Each
CUP HOLDER
There will be
four (
4 )
cup holder(s) provided. Each cup holder will be
4.00 " in diameter x
4.00 "
high. An approximate
1.00 " wide recess in the cup holder will allow it to hold beverage containers with handles.
Black rubber matting will be provided on the bottom of each cup holder.
The cup holder(s) will be painted to match the cab interior and located Mount at Pick-up
.
0629017
Work Surface, 3/16" Alum, Full Eng
Tnl, Flat, Lower Rear, Rear Lip,
Vel/Imp FR
WORK SURFACE
There will be a work surface provided on the engine tunnel. The work surface will cover the entire engine tunnel and will be constructed of
0.188
" aluminum to allow the mounting of equipment.
The work surface will continue horizontally to the flat portion at the rear of the engine tunnel. The work surface will drop to the lower flat portion of the engine tunnel and finish at the end of the engine tunnel. The lower portion of the work surface will be provided with a
3.00 "
lip. The work
surface will be
painted to match the cab interior
.
0745931
Modification, Reinforcement, Officer's
Side Recessed Dash, Imp/Vel
MODIFICATION/REINFORCEMENT OF OFFICER'S DASH
The area under the officer's side dash will be reinforced with an aluminum plate for a more rigid mounting for the customer's computer mount. The plate will be painted to match the cab interior. 0748671
Cab Interior, Vinyl, Velocity FR,
CARE
CAB INTERIOR
With safety as the primary objective, the wrap-around style cab instrument panel will be designed with unobstructed visibility to instrumentation. The dash layout will provide the driver with a quick reference to gauges that allows more time to focus on the road.
The center console will be a high impact ABS polymer and will be easily removable.
The passenger side dashboard will be constructed of painted aluminum for durability and low maintenance. For enhanced versatility, the passenger side dash will include a flat working surface.
To provide optional (service friendly) control panels, switches and storage modules, a painted aluminum overhead console will also be provided.
To complete the cab front interior design, painted aluminum modesty panels will be provided under the dash on both sides of the cab. The driver side modesty panel will provide mounting for the battery switch and diagnostic connectors, while the passenger side modesty panel provides a glove box, and ground access to the main electrical distribution panel via quick quarter turn fasteners.
To provide a deluxe automotive interior, the engine tunnel, side walls and rear wall will be covered by a leather grain vinyl that is resistant to oil, grease, and mildew.
The headliner will be installed in both forward and rear cab sections. The headliner panel will be a composition of an aluminum panel covered with a sound barrier and upholstery.
The cab structure will include designated raceways for electrical harness routing from the front of the cab to the rear upper portion of the cab. Raceways will be extruded in the forward door frame, floor, walls and overhead in the area where the walls meet the ceiling. The raceways located in the floor will be covered by aluminum extrusion, while the vertical and overhead raceways will be covered by painted aluminum covers. The raceways will improve harness integrity by providing a continuous harness path that eliminates wire chafing and abrasion associated with exposed wiring or routing through drilled metal holes. Harnesses will be laid in place.
CAB INTERIOR UPHOLSTERY
The cab interior upholstery will be
36 oz dark silver gray vinyl
. All cab interior materials will meet
FMVSS
302
(flammability of interior materials).
0667943
Cab Interior, Paint Color,
Impel/Velocity FR
CAB INTERIOR PAINT
The following metal surfaces will be painted black, vinyl textured paint:
Modesty panel in front of driver
Vertical surface of dash in front of the officer (not applicable for recessed dash) Glove box in front of the officer (if applicable)
Power distribution in front of the officer
Rear heater vent panels
The remaining cab interior metal surfaces will be painted fire smoke gray, vinyl texture paint
.
0509532
Floor, Rubber Padded Cab & Crew
Cab, Imp/Vel
CAB FLOOR
The cab and crew cab floor areas will be covered with Polydamp ™
acoustical floor mat consisting
of a black pyramid rubber facing and closed cell foam decoupler.
The top surface of the material has a series of raised pyramid shapes evenly spaced, which offer a superior grip surface. Additionally, the material has a
0.25 " thick closed cell foam (no water
absorption) which offers a sound dampening material for reducing sound levels. 19 989
Bid #:
0741239
HVAC, Heavy-Duty, Impel/Velocity
FR, CARE
DEFROST/AIR CONDITIONING SYSTEM
A ceiling mounted combination heater, defroster and air conditioning system will be installed in the cab above the engine tunnel area.
Cab Defroster
A
54,000
BTU heater-defroster unit with
690
SCFM of air flow will be provided inside the cab. The
heater-defrost will be installed in the forward portion of the cab ceiling. Air outlets will be strategically located in the cab header extrusion per the following:
One (
1 ) adjustable will be directed towards the left side cab window One (
1 ) adjustable will be directed towards the right side cab window Six (
6 ) fixed outlets will be directed at the windshield
The defroster will be capable of clearing
98 percent of the windshield and side glass when tested under conditions where the cab has been cold soaked at
0 degrees Fahrenheit for
10 hours, and
a
2 ounce per square inch layer of frost/ice has been able to build up on the exterior windshield.
The defroster system will meet or exceed SAE J
382
requirements.
Cab/Crew Auxiliary Heater
There will be
no auxiliary heater provided in the rear facing seat risers .
Air Conditioning
A
19.10 cubic inch compressor will be installed on the engine.
A roof-mounted condenser with a
78,000
BTU output at
2,400
SCFM that meets and exceeds the
performance specification will be installed on the cab roof. The condenser cover to be painted to
match the cab roof
.
The air conditioning system will be capable of cooling the average cab temperature from 100
degrees Fahrenheit to
75 degrees Fahrenheit at
50 percent relative humidity within
30 minutes.
The cooling performance test will be run only after the cab has been heat soaked at 100
degrees
Fahrenheit for a minimum of
4 hours.
The evaporator unit will be installed in the rear portion of the cab ceiling over the engine tunnel.
The evaporator will include one (
1 ) high performance heating core, one (
1 ) high performance
cooling core with (
1 ) plenum directed to the front and one (
1 ) plenum directed to the rear of the
cab.
The evaporator unit will have a
52,000
BTU at
690
SCFM rating that meets and exceeds the
performance specifications.
Adjustable air outlets will be strategically located on the forward plenum cover per the following:
Four (
4 ) will be directed towards the seating position on the left side of the cab Four (
4 ) will be directed towards the seating position on the right side of the cab Adjustable air outlets will be strategically located on the evaporator cover per the following:
Five (
5 ) will be directed towards crew cab area
A high efficiency particulate air (HEPA) filter will be included for the system. Access to the filter cover will be
secured with four (
4 ) screws
.
The air conditioner refrigerant will be R-
134
A and will be installed by a certified technician.
Climate Control
An automotive style controller will be provided to control the heat and air conditioning system within the cab. The controller will have three (
3 ) functional knobs for fan speed, temperature, and
air flow distribution (front to rear) control.
The system will control the temperature of the cab and crew cab automatically by pushing the center of the fan speed control knob. Rotate the center temperature control knob to set the cab and crew cab temperature.
The AC system will be manually activated by pushing the center of the temperature control knob.
Pushing the center of the air flow distribution knob will engage the AC for max defrost, setting the fan speeds to
100
percent and directing all air flow to the overhead forward position.
Gravity Drain Tubes
Two (
2 ) condensate drain tubes will be provided for the air conditioning evaporator. The drip pan will have two (
2 ) drain tubes plumbed separately to allow for the condensate to exit the drip pan.
No pumps will be provided.
The drain tubes will terminate under the cab, on the inboard side of the front wheelwells. 0627910
Sun Visor, Vinyl/Fabric, Imp/Vel
SUN VISORS
There will be two (
2 )
vinyl
covered sun visors provided. The sun visors will be located above the windshield with one (
1 ) mounted on each side of the cab.
There will be
a polished stainless steel bracket
provided to help secure each sun visor in the
stowed position.
0548173
Grab Handles, Driver and Passenger
Door Post, Imp/Vel
GRAB HANDLE
A black rubber covered grab handle will be mounted on the door post of the driver side and passenger side cab door to assist in entering the cab. The grab handle will be securely mounted to the post area between the door and windshield.
0583938
Lights, Engine Compt, Custom, Auto
Sw, Wln 3SC0CDCR, 3" LED, Trim
ENGINE COMPARTMENT LIGHTS
There will be
one (
1 )
Whelen, Model
3 SC
0 CDCR,
12 volt DC,
3.00 " white LED light(s) with
Whelen, Model
3 FLANGEC, chrome flange kit(s) installed under the cab to be used as engine compartment illumination.
These light(s) will be activated automatically when the cab is raised. 0122516
Fluid Check Access, Imp/Vel
ACCESS TO ENGINE DIPSTICKS
For access to the engine oil and transmission fluid dipsticks, there will be a door on the engine tunnel, inside the crew cab. The door will be on the rear wall of the engine tunnel, on the vertical surface. The door will be flush with the wall of the engine tunnel.
The engine oil dipstick will allow for checking only. The transmission dipstick will allow for both checking and filling. An additional port will be provided for filling the engine oil.
The door will have a rubber seal for thermal and acoustic insulation. One ( 1 )
flush lift and turn
latch
will be provided on the access door.
20 989
Bid #:
0002501
Map box, 4 bin/30 Deg Slant, Custom
Chassis
MAP BOX
A map box with four (
4 ) bins, open from top, will be installed
Mount at Pick-up
. The map box will
be divided into four (
4 ) bins, each being
12.50 " wide x
2.25 " high x
12.00 " deep. Each bin will
slant
30 degrees from horizontal. The map box will be constructed of . 125
" aluminum and will be
painted to match the cab interior.
0828042
Side Roll and Frontal Impact
Protection, SRS
CAB SAFETY SYSTEM
The cab will be provided with a safety system designed to protect occupants in the event of a side roll or frontal impact, and will include the following:
A supplemental restraint system (SRS) sensor will be installed on a structural cab member behind the instrument panel. The SRS sensor will perform real time diagnostics of all critical subsystems and will record sensory inputs immediately before and during a side roll or frontal impact event.
A fault-indicating light will be provided on the vehicle's instrument panel allowing the driver to monitor the operational status of the SRS system.
A driver side front air bag will be mounted in the steering wheel and will be designed to protect the head and upper torso of the occupant, when used in combination with the 3 -point seat belt.
A passenger side knee bolster air bag will be mounted in the modesty panel below the dash panel and will be designed to protect the legs of the occupant, when used in combination with the 3 -point seat belt.
Air curtains will be provided in the outboard bolster of outboard seat backs to provide a cushion between occupant and the cab wall.
Suspension seats will be provided with devices to retract them to the lowest travel position during a side roll or frontal impact event.
Seat belts will be provided with pre-tensioners to remove slack from the seat belt during a side roll or frontal impact event (with the exception of command chairs located in the command cab).
Frontal Impact Protection
The SRS system will provide protection during a frontal or oblique impact event. The system will activate when the vehicle decelerates at a predetermined G force known to cause injury to the occupants. The cab and chassis will have been subjected, via third party test facility, to a crash impact during frontal and oblique impact testing. Testing included all major chassis and cab components such as mounting straps for fuel and air tanks, suspension mounts, front suspension components, rear suspensions components, frame rail cross members, engine and transmission and their mounts, pump house and mounts, frame extensions and body mounts. The testing provided configuration specific information used to optimize the timing for firing the safety restraint system. The sensor will activate the pyrotechnic devices when the correct crash algorithm, wave form, is detected.
The SRS system will deploy the following components in the event of a frontal or oblique impact event:
Driver side front air bag
Passenger side knee bolster air bag
Air curtains mounted in the outboard bolster of outboard seat backs Suspension seats will be retracted to the lowest travel position Seat belts will be pre-tensioned to firmly hold the occupant in place Side Roll Protection
The SRS system will provide protection during a fast or slow 90 degree roll to the side, in which
the vehicle comes to rest on its side. The system will analyze the vehicle's angle and rate of roll to determine the optimal activation of the advanced occupant restraints.
The SRS system will deploy the following components in the event of a side roll:
Air curtains mounted in the outboard bolster of outboard seat backs Suspension seats will be retracted to the lowest travel position Seat belts will be pre-tensioned to firmly hold the occupant in place 0622618
Seating Capacity, 5 Belted Seats
SEATING CAPACITY
The seating capacity of the vehicle (including tiller cab and belted seat positions in the rescue body) will be five (
5 ).
0697005
Seat, Driver, Pierce PS6, Premium,
Air Ride, High Back, Safety,
PRIMARY
DRIVER SEAT
A Pierce PS
6 ® seat will be provided in the cab for the driver. The seat design will be a cam action type with air suspension. For increased convenience, the seat will include electric controls to adjust the rake (
15 degrees), height (
1.75 " travel) and horizontal (
7.00 " travel) position. Electric
controls will be located below the forward part of the seat cushion. To provide flexibility for multiple driver configurations, the seat will have a reclining back, adjustable from 20 degrees
back to
45 degrees forward. Providing for maximum comfort, the seat back will be a high back style with manual lumbar adjustment lever, for lower back support, and will include minimum
7.50 " deep side bolster pads for maximum support. The lumbar adjustment lever will be easily located at the lower outboard position of the seat cushion. For optimal comfort, the seat will be provided with
17.00 " deep dual density foam cushions designed with EVC (elastomeric vibration control).
The seat will include the following features incorporated into the side roll protection system:
Side air curtain will be mounted integral to the outboard bolster of the seat back. The air curtain will be covered by a decorative panel when in the stowed position.
A suspension seat safety system will be included. When activated in the event of a side roll, this system will pretension the seat belt and retract the seat to its lowest travel position.
The seat will be furnished with a
3 -point, shoulder type seat belt. The seat belt will be furnished with dual automatic retractors that will provide ease of operation in the normal seating position. 21 989
Bid #:
0696996
Seat, Officer, Pierce PS6, Premium,
Air Ride, High Back, Safety,
PRIMARY
OFFICER SEAT
A Pierce PS
6 ® seat will be provided in the cab for the officer. The seat will be a cam action type, with air suspension. For increased convenience, the seat will include a manual control to adjust the horizontal position (
6.00 " travel). The manual horizontal control will be a towel-bar style located below the forward part of the seat cushion. To provide flexibility for multiple passenger configurations, the seat will have a reclining back adjustable from 20 degrees back to
0 degrees
forward. The seat back will be a high back style with manual lumbar adjustment lever, and will include minimum
7.50 " deep side bolster pads for maximum support. For optimal comfort, the seat will be provided with
17.00 " deep dual density foam cushions designed with EVC (elastomeric vibration control). To ensure safe operation, the seat will be equipped with seat belt sensors in the seat cushion and belt receptacle that will activate an alarm indicating a seat is occupied but not buckled.
The seat will include the following features incorporated into the side roll protection system:
Side air curtain will be mounted integral to the outboard bolster of the seat back. The air curtain will be covered by a decorative panel when in the stowed position.
A suspension seat safety system will be included. When activated this system will pretension the seat belt and retract the seat to its lowest travel position.
The seat will be furnished with a
3 -point, shoulder type seat belt. The seat belt will be furnished with dual automatic retractors that will provide ease of operation in the normal seating position. 0002517
Not Required, Radio Compartment
0765826
SP
Cabinet, Rear Facing, LS, 30.5 W x
30 H x 24 D, Ext Acc Only, Imp/Vel
REAR FACING LEFT SIDE CABINET
A rear facing cabinet will be provided in the crew cab at the left side outboard position with exterior access.
The cabinet will be
30.50 " wide x
30.00 " high x
24.00 " deep.
The cabinet will include
one (
1 ) infinitely adjustable shelf with a
0.75 " up-turned lip
painted to
match the cab interior
.
The cabinet will include
no louvers
.
The cabinet will provide exterior access only with
one (
1 ) reverse hinged double pan door painted
to match the cab exterior with a locking D-ring latch with #751
key
. A
pneumatic stay arm
will be
provided as a door stop. The clear door opening will
19.50 " wide x
27.50 " high.
The exterior access will be provided with
no scuffplate
on the lower door frame.
The cabinet will be constructed of smooth aluminum and painted to match the cab interior.
Cabinet Light
There will be
one (
1 ) white LED strip light installed on the left side of the exterior cabinet door opening and one (
1 ) white LED strip light installed on the right side of the exterior cabinet door opening
. The lighting will be controlled by an automatic door switch. 0102783
Not Required, Seat, Rr Facing C/C,
Center
0815943
SP
Cabinet, Rear Facing, RS, 26.5 W x
30 H x 21.5 D, Ext Acc Only, Sp Mtg,
Imp/Vel
REAR FACING RIGHT SIDE CABINET
A rear facing cabinet will be provided in the crew cab at the right side outboard position. The cabinet will be mounted off the edge of the seat riser.
The cabinet will be
26.50 " wide x
30.00 " high x
21.50 " deep.
The cabinet will include
one (
1 ) infinitely adjustable shelf with a
0.75 " up-turned lip
painted to
match the cab interior
.
The cabinet will include
no louvers
.
The cabinet will only provide access from outside the cab with one (
1 ) reverse hinged double pan
door painted to match the cab exterior with a locking D-ring latch with #751
key
. A
pneumatic stay
arm
will be provided as a door stop. The exterior clear door opening will be
19.50 " wide x
27.50 "
high. The door will be located on the side of the cab over the wheelwell.
The exterior access will be provided with
no scuffplate
on the lower door frame.
The cabinet will be constructed of smooth aluminum and painted to match the cab interior.
Cabinet Light
There will be
one (
1 ) white LED strip light installed on the left side of the exterior cabinet door opening and one (
1 ) white LED strip light installed on the right side of the exterior cabinet door opening
. The lighting will be controlled by an automatic door switch. 0108189
Not Required, Seat, Forward Facing
C/C, LS Outboard
0698519
Seat, Fwd Fcng C/C, Ctr, (2) Pierce
PS6, Premium,Hi-
Back,Foldup,Safety,SECONDARY
FORWARD FACING CENTER SEATS
There will be two (
2 ) forward facing, Pierce PS
6 ® seats provided at the center position in the
crew cab. The seat back will be a high back style with
7.5 degree fixed recline angle, and will
include minimum
7.50 " deep side bolster pads for maximum support. For optimal comfort, the seats will be provided with
17.00 " deep, foldup, dual density foam cushions designed with EVC (elastomeric vibration control). To ensure safe operation, the seats will be equipped with seat belt sensors in the seat cushion and belt receptacle that will activate an alarm indicating a seat is occupied but not buckled.
The seats will include the following feature incorporated into the side roll protection system:
A seat safety system will be included. When activated, this system will pretension the seat belt around the occupant to firmly hold them in place in the event of a side roll.
The seats will be furnished with a
3 -point, shoulder type seat belt. The seat belts will be furnished with dual automatic retractors that will provide ease of operation in the normal seating position. 22 989
Bid #:
0108190
Not Required, Seat, Forward Facing
C/C, RS Outboard
0617410
Matting, Turtle Tile, EMS Compt,
Shelving, 0.75" Thick
MATTING IN EMS COMPARTMENT
Turtle Tile vinyl matting will be provided in
two (
2 )
EMS compartment shelves,
Fwd Facing
Cabinets in Crew Cab.
1 ) in lower Compt. and
1 ) in Upper Compt.
. Tile color will be
black
.
0746506
Lip, Top of Interior Cabinet, All Sides,
2nd
LIP ON CABINET
There will be a
1.00 "
lip provided around the top perimeter of the cabinet. There will NOT be anything stored on the top portion without restraints
There will be
two (
2 )
cabinets(s) provided with the lip
On top of LS & RS EMS Cabinets
.
0752005
Lip, Top of Interior Cabinet, All Sides
LIP ON CABINET
There will be a
1.00 "
lip provided around the top perimeter of the cabinet. There will NOT be anything stored on the top portion without restraints.
There will be
one (
1 )
cabinets(s) provided with the lip
One (
1 ) on Engine Tunnel Work surface,
Match
38759
.
0820412
Fasteners, Mechanical, Strip Lighting,
Cab Compartments
BRACKETS/CLAMPS FOR COMPARTMENT LIGHTS
Metal clamps will be used to retain the strip lighting in all cab compartments. 0766467
Upholstery, Seats In Cab, All Vinyl,
Seats Inc, CARE
SEAT UPHOLSTERY
All seat upholstery will be leather grain
36 oz dark silver gray vinyl
resistant to oil, grease and
mildew. The cab and tiller cab (if applicable) will have four (
4 )
seating positions.
0511471
No SCBA Brackets Required In Cab
Seats, Imp/Vel, AXT 2010, SFR/Enf
0639023
Driver Seat Hooked to Battery
Switched IPO Ignition Switched
DRIVER SEAT POWER
The driver seat power for the adjustability will be powered when the master battery switch is turned on in place of the standard ignition switched.
0734952
Door, Access, Front, (2) Rear Facing
Seat Risers, No Heater
ACCESS DOOR
An access door will be provided in the front edge of each rear facing seat riser with a drop down door. The drop down door will be provided with a
Southco C
2 chrome raised trigger lever latch
and
painted to match the cab interior
. There will be
no louvers
.
0603867
Seat Belt, ReadyReach
SEAT BELTS
All seating positions in the cab, crew cab and tiller cab (if applicable) will have red
seat belts.
To provide quick, easy use for occupants wearing bunker gear, the female buckle and seat belt webbing length will meet or exceed the current edition of applicable NFPA and CAN/ULC - S 515
standards.
The
3 -point shoulder type seat belts will also include the ReadyReach® D-loop assembly to the shoulder belt system. The ReadyReach feature adds an extender arm to the D-loop location placing the D-loop in a closer, easier to reach location.
Any flip up seats will include a
3 -point shoulder type belts only.
0604867
Seat Belt Height Adjustment, 4 Seats,
Imp/Vel
SHOULDER HARNESS HEIGHT ADJUSTMENT
All seating positions furnished with
3 -point shoulder type seat belts will include a height adjustment. This adjustment will optimize the belts effectiveness and comfort for the seated firefighter.
A total of four (
4 ) seating positions will have the adjustable shoulder harness. 0627014
Pick Not Required, Seat Belt Color
Selected in Seat Belt Category
0817557
Helmet Storage, Provided by Fire
Department, NFPA/ULC 2024
HELMET STORAGE PROVIDED BY FIRE DEPARTMENT
NFPA
1900
,
2024
edition, section
11.1.8.4.1 and CAN/ULC
515:2024
edition, section
5.2 ,
requires a location for helmet storage be provided.
There is no helmet storage on the apparatus as manufactured. The fire department will provide a location for storage of helmets.
23 989
Bid #:
0647647
Lights, Dome, FRP Dual LED 4 Lts
CAB DOME LIGHTS
There will be four (
4 ) dual LED dome lights with
grey
bezels provided. Two (
2 ) lights will be
mounted above the inside shoulder of the driver and officer and two ( 2 ) lights will be installed and
located, one (
1 ) on each side of the crew cab.
The color of the LED's will be
red and white
.
The white LED's will be controlled by
the door switches and the lens switch
.
The color LED's will be controlled by
the lens switch
.
All dome lights on the apparatus will be illuminated per the current edition of applicable NFPA standards per seating position.
0652881
Lights, Dome, FRP Dual LED
ADDITIONAL DOME LIGHTS
There will be
one (
1 )
dual LED dome light(s) with
grey
bezel(s) mounted in the cab and/or crew
cab located
(additional light) should be centered in cab ceiling in front of forward facing cabinet in crew cab area
.
The color of the LED's will be
red and white
.
The white LED(s) will be controlled by
the door switches and the lens switch
.
The color LED(s) will be controlled by
the lens switch
.
All dome lights on the apparatus will be illuminated per the current edition of applicable NFPA standards per seating position.
The light(s) may be load managed when the parking brake is applied. 0896451
Enhanced Software for Cab and
Crew Cab Dome Lts
ENHANCED SOFTWARE FOR CAB AND CREW CAB DOME LIGHTS
The cab and crew cab dome lights will remain on for
10 seconds for improved visibility after the
doors are closed.
The dome lights will dim after
10 seconds or immediately if the vehicle's transmission is put into gear.
0628472
Light, Map, Overhead, Peterson
M371S LED, Rectangular w/Switch
2lts
OVERHEAD MAP LIGHTS
There will be two (
2 ) Peterson, Model M
371
S, rectangular LED adjustable map lights installed in
the cab:
One (
1 ) overhead in front of the driving position.
One (
1 ) overhead in front of the passenger's position.
Each light will include a switch on the light housing.
The light switches will be connected
directly to the battery switched power
.
0727540
Spotlight, Golight/RadioRay, Model
20**4GT, LED, 1 Lt
CAB SPOTLIGHT
There will be one (
1 ) Golight/RadioRay®, Model
20 **
4 GT,
black
LED spotlight located on the cab
roof,
Centered on Roof Behind Lightbar and ahead of HVAC condenser. Option 641379
has been
added to bid to create needed space
. The spotlight will be mounted
on a painted Z bracket
.
This light may be load managed when the parking brake is applied. 0650074
Controller, Spotlight, Golight, Wired
Dash Mt, 1 Lt
Spotlight Controller
There will be one (
1 ) wired dash mounted remote provided for the spotlight. 0649964
Location, Spotlight Controller,
Officer's Side
SPOTLIGHT CONTROLLER LOCATION
The remote to control each spotlight will be located within reach of the officer. 0804719
Handlts, (4) Streamlight, Fire Vulcan,
44451, C4 LED, Tail Lts, 12v, Orange
HAND HELD LIGHT
There will be four (
4 ) Streamlight, Fire Vulcan, Model
#44451
, hand lights provided with a vehicle
mount with
12 VDC direct wire charging rack and quick release buckle strap mounted two (
2 )
Mounted per Worksurface layout drawing. (Match
38759
), One (
1 ) On center Crew Cabinet
(location TBD) and One (
1 ) In RS
1 (Location TBD)cab
.
Each light housing will be orange in color and be provided with a C 4 , LED and two (
2 ) "ultra bright
blue tail light LEDs". The tail light LEDs will have a dual mode of blinking or steady. 0568369
Cab Instruments, Ivory Gauges,
Chrome Bezels, Impel/Velocity 2010
CAB INSTRUMENTATION
The cab instrument panel will consist of gauges, an LCD display, telltale indicator lights, alarms, control switches, and a diagnostic panel. The function of instrument panel controls and switches will be identified by a label adjacent to each item. Actuation of the headlight switch will illuminate the labels in low light conditions. Telltale indicator lamps will not be illuminated unless necessary.
The cab instruments and controls will be conveniently located within the forward cab section directly forward of the driver. Gauge and switch panels will be designed to be removable for ease of service and low cost of ownership.
Gauges
The gauge panel will include the following ten (
10 ) ivory gauges with chrome bezels to monitor
vehicle performance:
Voltmeter gauge (Volts)
Low volts (
11.8 VDC)
Amber indicator on gauge assembly with alarm
High volts (
15 VDC)
Amber indicator on gauge assembly with alarm
Very low volts (
11.3 VDC)
Amber indicator on gauge assembly with alarm
Very high volts (
16 VDC)
Amber indicator on gauge assembly with alarm
24 989
Bid #:
Tachometer (RPM)
Speedometer (Primary (outside) MPH, Secondary (inside) Km/H) Fuel level gauge (Empty - Full in fractions)
Low fuel (
1/8
full)
Amber indicator on gauge assembly with alarm
Very low fuel (
1/32
) fuel
Amber indicator on gauge assembly with alarm
Engine oil pressure gauge (PSI)
Low oil pressure to activate engine warning lights and alarms Red indicator on gauge assembly with alarm
Front air pressure gauge (PSI)
Low air pressure to activate warning lights and alarm
Red indicator on gauge assembly with alarm
Rear air pressure gauge (PSI)
Low air pressure to activate warning lights and alarm
Red indicator on gauge assembly with alarm
Transmission oil temperature gauge (Fahrenheit)
High transmission oil temperature activates warning lights and alarm Amber indicator on gauge assembly with alarm
Engine coolant temperature gauge (Fahrenheit)
High engine temperature activates an engine warning light and alarm Red indicator on gauge assembly with alarm
Diesel Exhaust Fluid Level Gauge (Empty - Full in fractions) Low fluid (
1/8
full)
Amber indicator on gauge assembly with alarm
All gauges and gauge indicators will perform prove out at initial power-up to ensure proper performance.
Indicator Lamps
To promote safety, the following telltale indicator lamps will be integral to the gauge assembly and are located above and below the center gauges. The indicator lamps will be "dead-front" design that is only visible when active. The colored indicator lights will have descriptive text or symbols.
The following amber telltale lamps will be present:
Low coolant
Trac cntl (traction control) (where applicable)
Check engine
Check trans (check transmission)
Aux brake overheat (Auxiliary brake overheat)
Air rest (air restriction)
Caution (triangle symbol)
Water in fuel
DPF (engine diesel particulate filter regeneration)
Trailer ABS (where applicable)
Wait to start (where applicable)
HET (engine high exhaust temperature) (where applicable) ABS (antilock brake system)
MIL (engine emissions system malfunction indicator lamp) (where applicable) SRS (supplemental restraint system) fault (where applicable) DEF (low diesel exhaust fluid level)
The following red telltale lamps will be present:
Warning (stop sign symbol)
Seat belt
Parking brake
Stop engine
Rack down
The following green telltale lamps will be provided:
Left turn
Right turn
Battery on
The following blue telltale lamp will be provided:
High beam
Alarms
Audible steady tone warning alarm: A steady audible tone alarm will be provided whenever a warning message is present.
Audible pulsing tone caution alarm: A pulsing audible tone alarm (chime/chirp) will be provided whenever a caution message is present without a warning message being present.
Alarm silence: Any active audible alarm will be able to be silenced by holding the ignition switch at the top position for
3 to
5 seconds. For improved safety, silenced audible alarms will intermittently chirp every
30 seconds until the alarm condition no longer exists. The intermittent chirp will act as a reminder to the operator that a caution or warning condition still exists. Any new warning or caution condition will enable the steady or pulsing tones respectively.
Indicator Lamp and Alarm Prove-Out
Telltale indicators and alarms will perform prove-out at initial power-up to ensure proper performance.
Control Switches
For ease of use, the following controls will be provided immediately adjacent to the cab instrument panel within easy reach of the driver.
Emergency master switch: A molded plastic push button switch with integral indicator lamp will be provided. Pressing the switch will activate emergency response lights and siren control. A green lamp on the switch provides indication that the emergency master mode is active. Pressing the switch again disables the emergency master mode.
Headlight / Parking light switch: A three (
3 )-position maintained rocker switch will be
provided. The first switch position will deactivate all parking lights and the headlights. The second switch position will activate the parking lights. The third switch position will activate the headlights.
Panel backlighting intensity control switch: A three (
3 )-position momentary rocker switch
25 989
Bid #:
will be provided. The first switch position decreases the panel backlighting intensity to a minimum level as the switch is held. The second switch position is the default position that does not affect the backlighting intensity. The third switch position increases the panel backlighting intensity to a maximum level as the switch is held.
The following standard controls will be integral to the gauge assembly and are located below the right hand gauges. All switches have backlit labels for low light applications.
High idle engagement switch: A two (
2 )-position momentary rocker switch with integral
indicator lamp will be provided. The first switch position is the default switch position.
The second switch position will activate and deactivate the high idle function when pressed and released. The "Ok To Engage High Idle" indicator lamp must be active for the high idle function to engage. A green indicator lamp integral to the high idle engagement switch will indicate when the high idle function is engaged. "Ok To Engage High Idle" indicator lamp: A green indicator light will be provided next to the high idle activation switch to indicate that the interlocks have been met to allow high idle engagement.
The following standard controls will be provided adjacent to the cab gauge assembly within easy reach of the driver. All switches will have backlit labels for low light applications.
Ignition switch: A three (
3 )-position maintained/momentary rocker switch will be provided.
The first switch position will deactivate vehicle ignition. The second switch position will activate vehicle ignition. The third momentary position will disable the Command Zone audible alarm if held for
3 to
5 seconds. A green indicator lamp will be activated with vehicle ignition.
Engine start switch: A two (
2 )-position momentary rocker switch will be provided. The first switch position is the default switch position. The second switch position will activate the vehicle's engine. The switch actuator is designed to prevent accidental activation. 4 -way hazard switch: A two (
2 )-position maintained rocker switch will be provided. The first switch position will deactivate the
4 -way hazard switch function. The second switch
position will activate the
4 -way hazard function. The switch actuator will be red and includes the international
4 -way hazard symbol.
Heater, defroster, and air conditioning control panel.
Turn signal arm: A self-canceling turn signal with high beam headlight and windshield wiper/washer controls will be provided. The windshield wiper control will have high, low, and intermittent modes.
Parking brake control: An air actuated push/pull park brake control valve will be provided.
Chassis horn control: Activation of the chassis horn control will be provided through the center of the steering wheel.
Custom Switch Panels
The design of cab instrumentation will allow for emergency lighting and other switches to be placed within easy reach of the operator thus improving safety. There will be positions for up to four (
4 ) switch panels in the overhead console on the driver's side, up to four ( 4 )
switch panels in the engine tunnel console facing the driver, up to four ( 4 ) switch panels in
the overhead console on the officer's side and up to two ( 2 ) switch panels in the engine
tunnel console facing the officer. All switches will have backlit labels for low light applications.
Diagnostic Panel
A diagnostic panel will be accessible while standing on the ground and located inside the driver's side door left of the steering column. The diagnostic panel will allow diagnostic tools such as computers to connect to various vehicle systems for improved troubleshooting providing a lower cost of ownership. Diagnostic switches will allow ABS systems to provide blink codes should a problem exist.
The diagnostic panel will include the following:
Engine diagnostic port
Transmission diagnostic port
ABS diagnostic port
SRS diagnostic port (where applicable)
Command Zone USB diagnostic port
ABS diagnostic switch (blink codes flashed on ABS telltale indicator) Diesel particulate filter regeneration switch (where applicable) Diesel particulate filter regeneration inhibit switch (where applicable) Cab LCD Display
A digital four (
4 )-row by
20 -character dot matrix display will be integral to the gauge panel.
The display will be capable of showing simple graphical images as well as text. The display will be split into three (
3 ) sections. Each section will have a dedicated function.
The upper left section will display the outside ambient temperature.
The upper right section will display, along with other configuration specific information:
Odometer
Trip mileage
PTO hours
Fuel consumption
Engine hours
The bottom section will display INFO, CAUTION, and WARNING messages. Text messages will automatically activate to describe the cause of an audible caution or warning alarm.
The LCD will be capable of displaying multiple text messages should more than one caution or warning condition exist.
0509511
Air Restriction Indicator, Imp/Vel,
AXT, Enf MUX
AIR RESTRICTION INDICATOR
A high air restriction warning indicator light LCD message with amber warning indicator and audible alarm will be provided.
26 989
Bid #:
0606017
SP
Light, Do Not Move Apparatus, Wln
VTX609R Red LED 2lts, DS PS
Indicator
"DO NOT MOVE APPARATUS" INDICATOR
There will be two (
2 ) Whelen, Model VTX
609
R, red LED indicator lights with chrome trim located
in the driving compartment. The lights will be illuminated automatically per the current NFPA requirements. The light will be labeled "Do Not Move Apparatus If Light Is On." One (
1 ) light will be installed over the driver's position.
One (
1 ) light will be installed over the passenger's position in the cab.
One light will indicate the status of the doors on the driver's side of the apparatus and one light will indicate the status of the doors on the passenger's side and rear of apparatus.
All other items that activate the "Do Not Move Truck" indicator light will activate both flashing red indicator lights.
The same circuit that activates the Do Not Move Apparatus indicator will activate a steady tone
alarm
when the parking brake is released.
0509042
Messages, Open Dr/DNMT, Color
Dsply,
DO NOT MOVE TRUCK MESSAGES
Messages will be displayed on the Command Zone
™,
color display located within sight of the
driver whenever the Do Not Move Truck light is active. The messages will designate the item or items not in the stowed for vehicle travel position (parking brake disengaged).
The following messages will be displayed (where applicable):
Do Not Move Truck
DS Cab Door Open (Driver Side Cab Door Open)
PS Cab Door Open (Passenger's Side Cab Door Open)
DS Crew Cab Door Open (Driver Side Crew Cab Door Open)
PS Crew Cab Door Open (Passenger's Side Crew Cab Door Open) DS Body Door Open (Driver Side Body Door Open)
PS Body Door Open (Passenger's Side Body Door Open)
Rear Body Door Open
DS Ladder Rack Down (Driver Side Ladder Rack Down)
PS Ladder Rack Down (Passenger Side Ladder Rack Down)
Deck Gun Not Stowed
Lt Tower Not Stowed (Light Tower Not Stowed)
Fold Tank Not Stowed (Fold-A-Tank Not Stowed)
Aerial Not Stowed (Aerial Device Not Stowed)
Stabilizer Not Stowed
Steps Not Stowed
Handrail Not Stowed
Any other device that is opened, extended, or deployed that creates a hazard or is likely to cause major damage to the apparatus if the apparatus is moved will be displayed as a caution message after the parking brake is disengaged.
0611681
Switching, Cab, Membrane,
Impel/Velocity, AXT WiFi MUX
SWITCH PANELS
The emergency light switch panel will have a master switch for ease of use plus individual switches for selective control. Each switch panel will contain eight ( 8 ) membrane-type switches
each rated for one million (
1,000,000
) cycles. Panels containing less than eight (
8 ) switch
assignments will include non-functioning black appliqués. Documentation will be provided by the manufacturer indicating the rated cycle life of the switches. The switch panel(s) will be located in the overhead position above the windshield on the
driver side overhead
to allow for easy access.
Additional switch panel(s) will be located in the overhead position(s) above the windshield or in designated locations on the lower instrument panel layout.
The switches will be membrane-type and also act as an integral indicator light. For quick, visual indication the entire surface of the switch will be illuminated white whenever back lighting is activated and illuminated green whenever the switch is active. An active illuminated switch will flash when interlock requirements are not met or device is actively being load managed. For ease of use, a two (
2 )-ply, scratch resistant laser engraved Gravoply label indicating the use of each switch will be placed in the center of the switch. The label will allow light to pass through the letters for ease of use in low light conditions.
0555915
Wiper Control, 2-Speed with
Intermittent, MUX, Impel/Velocity
WIPER CONTROL
For simple operation and easy reach, the windshield wiper control will be an integral part of the directional light lever located on the steering column. The wiper control will include high and low wiper speed settings, a one (
1 )-speed intermittent wiper control and windshield washer switch.
The control will have a "return to park" provision, which allows the wipers to return to the stored position when the wipers are not in use.
0002565
Hourmeter, Aerial Inside Cab
HOURMETER - AERIAL DEVICE
An hourmeter for the aerial device will be provided and located within the cab display or instrument panel.
0002615
Switch, Aerial 12V Master
AERIAL MASTER
There will be a master switch for the aerial operating electrical system provided. 0770696
Aerial PTO Activated with Aerial
Master Sw
AERIAL PTO ACTIVATION
The aerial PTO will be activated when the aerial master switch is activated and the interlocks are met.
27 989
Bid #:
0834413
USB, Cab, 4, 12V DC, Dual USB
Termination, Batt Dir.
NFPA1900/ULC
CAB USB
There will be four (
4 ) USB terminations
with a combination USB type A & C
, wired to battery
direct power, and provided per the following:
One (
1 ) within reach of the driver
One (
1 ) within reach of the passenger
Two (
2 ) on the rear of the engine tunnel, one (
1 ) each side.
Battery direct loads cannot be load managed.
0821239
Wiring, Spare, 20 A 12V DC, 6 Ckt
FB, Blue Sea 5025 Batt Dir 2nd
NFPA1900/ULC
SPARE CIRCUIT
There will be one (
1 ) pair of wires, including a positive and a negative, installed on the apparatus.
The wires will have the following features:
The positive wire will be connected
directly to the battery power
.
The negative wire will be connected to ground.
Wires will be capable of carrying
20 amps.
Power and ground will terminate
in LS
1 of the trailer body, Match
30972
, front bulkhead
.
Termination will be to a Blue Sea System, Model
5025
,
6 circuit with negative bus bar. The
terminal block will include a cover with circuit labels.
Wires will be protected to meet the NFPA Automotive Fire Apparatus standard.
This circuit(s) may be load managed when the parking brake is set. 0821240
Wiring, Spare, 20 A 12V DC, 6 Ckt
FB, Blue Sea 5025 Batt Dir 3rd
NFPA1900/ULC
SPARE CIRCUIT
There will be one (
1 ) pair of wires, including a positive and a negative, installed on the apparatus.
The wires will have the following features:
The positive wire will be connected
directly to the battery power
.
The negative wire will be connected to ground.
Wires will be capable of carrying
20 amps.
Power and ground will terminate
RS
1 of the trailer body, Match
30972
front bulkhead
.
Termination will be to a Blue Sea System, Model
5025
,
6 circuit with negative bus bar. The
terminal block will include a cover with circuit labels.
Wires will be protected to meet the NFPA Automotive Fire Apparatus standard.
Battery Direct loads cannot be Load Managed
0821261
Wiring, Spare, 20 A 12V DC, 12
Circuit Fuse Block Blue Sea 5026
2nd NFPA1900/ULC
SPARE CIRCUIT
There will be
one (
1 )
pair of wires, including a positive and a negative, installed on the apparatus.
The wires will have the following features:
The positive wire will be connected
directly to the battery switched power
.
The negative wire will be connected to ground.
Wires will be capable of carrying
20 amps.
Power and ground will terminate
to be located at pickup, behind officer seat
.
Termination will be to a Blue Sea System, Model
5026
,
12 circuit with negative bus bar, straight
blade fuse block. The terminal block will include a cover with circuit labels.
Wires will be protected to meet the NFPA Automotive Fire Apparatus standard.
This circuit(s) may be load managed when the parking brake is set. 0821725
Wiring, Spare, 3 A 12V DC Batt Dir
1st NFPA1900/ULC
SPARE CIRCUIT
There will be
two (
2 )
pair of wires, including a positive and a negative, installed on the apparatus.
The wires will have the following features:
The positive wire will be connected
directly to the battery power
.
The negative wire will be connected to ground.
Wires will be capable of carrying
3.0 amps.
Power and ground will terminate
Per IP Layout, Matching
30972
.
Termination will be
with heat shrinkable butt splicing
.
Wires will be protected to meet the NFPA Automotive Fire Apparatus standard.
Battery Direct loads cannot be Load Managed
0562103
Wire, 14-ga. Spare, Dual Wire, pair
2nd
14 GAUGE SPARE WIRE
There will be a pair of
14 gauge wires, one (
1 ) with black insulation and one (
1 ) with white
insulation, included in a separate loom installed in the apparatus.
These wires will be routed from
3 ' Pigtail as high and forward on the backwall as possible and
extended to
Fuse block in LS
1 .
These wires will not be connected to any power source and will not be connected to the vehicle electrical system.
0566101
Recess, Dash Panel, Officer Side,
Vel/Imp
DASH PANEL RECESS
The dash panel across from the officer will be recessed to accommodate the mounting of miscellaneous items. The recess will be
7.25 " down x
7.81 " back and
20.88 " wide.
0758439
SP
Remote Control, Wired,
Programmable 3 Button 2nd
PROGRAMMABLE REMOTE CONTROL
There will be a wired remote control integrated into the switch panel Panel Position A. Match
387589
. The remote will have three (
3 ) individually programmable buttons for most garage door openers, and gate operators as well as the capability of controlling many lighting and security systems.
28 989
Bid #:
0655679
Remote Control, Wired,
Programmable 3 Button
PROGRAMMABLE REMOTE CONTROL
There will be a wired remote control integrated into the switch panel Panel Position A. Match
387589
. The remote will have three (
3 ) individually programmable buttons for most garage door openers, and gate operators as well as the capability of controlling many lighting and security systems.
0537251
Bracket, Mounting, For Push Buttons,
Officer Side, VEL/IMP
MOUNTING BRACKET FOR PUSH BUTTON CONTROLS
There will be a mounting bracket provided within easy reach of the officer next to the defrost air intake for the mounting of push button controls. The mounting bracket will be large enough to mount
Top Button - Air Horn Middle Button - Mechanical Siren Bottom - Button PS PTT controls
vertically, one in front of the other. The bracket will be fabricated from smooth aluminum and will be painted to match the cab interior.
0814201
Vehicle Information Center, 7" Color
Display, Touchscreen, MUX, CL714
INFORMATION CENTER
An information center employing a
7.00 " diagonal touch screen color LCD display will be encased in an ABS plastic housing.
The information center will have the following specifications:
Operate in temperatures from -
40 to
158
degrees Fahrenheit
LCD optically bonded to hardened AR glass lens
Five weather resistant user interface switches
Grey with black accents
Sunlight Readable
Linux operating system
Minimum of
1000
nits rated display
Display can be changed to an available foreign language A LCD display integral to the cab gauge panel will be included as outlined in the cab instrumentation area.
Programmed to read
US Customary
General Screen Design
Where possible, background colors will be used to provide "At a Glance" vehicle information. If information provided on a screen is within acceptable limits, a green background will be used.
If a caution or warning situation arises the following will occur:
An amber background/text color will indicate a caution condition A red background/text color will indicate a warning condition The information center will utilize an "Alert Center" to display text messages for audible alarm tones. The text messages will be written to identify the item(s) causing the audible alarm to sound. If more than one (
1 ) text message occurs, the messages will cycle every second until the problem(s) have been resolved. The background color for the "Alert Center" will change to indicate the severity of the "warning" message. If a warning and a caution condition occur simultaneously, the red background color will be shown for all alert center messages.
A label for each button will exist. The label will indicate the function for each active button for each screen. Buttons that are not utilized on specific screens will have a button label with no text or symbol.
Home/Transit Screen
This screen will display the following:
Vehicle Mitigation (if equipped)
Water Level (if the water level system includes compatible communications to the information center)
Foam Level (if the foam level system includes compatible communications to the information center)
Seat Belt Monitoring Screen
Tire Pressure Monitoring (if equipped)
Digital Speedometer
Active Alarms
On Scene Screen
This screen will display the following and will be auto activated with pump engaged (if equipped):
Battery Voltage
Fuel
Oil Pressure
Coolant Temperature
RPM
Water Level (if equipped)
Foam Level (if equipped)
Foam Concentration (if equipped)
Water Flow Rate (if equipped)
Water Used (if equipped)
Active Alarms
Virtual Buttons
There will be four (
4 ) virtual switch panel screens that match the overhead and lower lighting and HVAC switch panels.
Page Screen
The page screen will display the following and allow the user to progress into other screens for further functionality:
Diagnostics
Faults
Listed by order of occurrence
Allows to sort by system
Interlock
Throttle Interlocks
Pump Interlocks (if equipped)
Aerial Interlocks (if equipped)
PTO Interlocks (if equipped)
Load Manager
A list of items to be load managed will be provided. The list will provide a description of the load. 29 989
Bid #:
The lower the priority numbers the earlier the device will be shed should a low voltage condition occur.
The screen will indicate if a load has been shed (disabled) or not shed. "At a glance" color features are utilized on this screen.
Systems
Command Zone
Module type and ID number
Module Version
Input or output number
Circuit number connected to that input or output
Status of the input or output
Power and Constant Current module diagnostic information Foam (if equipped)
Pressure Controller (if equipped)
Generator Frequency (if equipped)
Live Data
General Truck Data
Maintenance
Engine oil and filter
Transmission oil and filter
Pump oil (if equipped)
Foam (if equipped)
Aerial (if equipped)
Setup
Clock Setup
Date & Time
12 or
24 hour format
Set time and date
Backlight
Daytime
Night time
Sensitivity
Unit Selection
Home Screen
Virtual Button Setup
On Scene Screen Setup
Configure Video Mode
Set Video Contrast
Set Video Color
Set Video Tint
Do Not Move
The screen will indicate the approximate location and type of item that is open or is not stowed for travel. The actual status of the following devices will be indicated Driver Side Cab Door
Passenger's Side Cab Door
Driver Side Crew Cab Door
Passenger's Side Crew Cab Door
Driver Side Body Doors
Passenger's Side Body Doors
Rear Body Door(s)
Ladder Rack (if applicable)
Deck Gun (if applicable)
Light Tower (if applicable)
Hatch Door (if applicable)
Stabilizers (if applicable)
Steps (if applicable)
Notifications
View Active Alarms
Shows a list of all active alarms including date and time of the occurrence is shown with each alarm
Silence Alarms - All alarms are silenced
Timer Screen
HVAC (if equipped)
Tire Information (if equipped)
Ascendant Set Up Confirmation (if equipped)
Button functions and button labels may change with each screen. 0816633
Collision Mitigation, HAAS Alert
(R2V), HA7
COLLISION MITIGATION
There will be a HAAS Alert®, Model HA
7 Responder-to-Vehicle (R
2 V) collision avoidance system
provided on the apparatus. The HA
7 cellular transponder module will be installed behind the cab windshield, as high and near to the center as practical, to allow clear visibility to the sky. The module dimensions are
5.40 " long x
2.70 " wide x
1.30 " high, and operating temperature range is
-
40 degrees Celsius to
85 degrees Celsius.
The transponder will be connected to the vehicle's emergency master circuit and battery direct power and ground.
While responding with emergency lights on, the HA
7 transponder sends alert messages via
cellular network to motorists in the vicinity of the responding truck that are equipped with the WAZE app.
While on scene with emergency lights on, the HA
7 transponder sends road hazard alerts to
motorists in the vicinity of the truck that are equipped with the WAZE app.
The HA
7 Responder-to-Vehicle (R
2 V) collision avoidance system will include
the transponder
and a
5 year cellular plan subscription
.
Activation of the HAAS Alert system requires a representative of the customer to accept the End User License Agreement (EULA) via an on-line portal.
30 989
Bid #:
0606249
Vehicle Data Recorder w/CZ and
Overhead Display Seat Belt Monitor
VEHICLE DATA RECORDER
There will be a vehicle data recorder (VDR) capable of reading and storing vehicle information provided.
The information stored on the VDR can be downloaded through a USB port mounted in a convenient location determined by cab model. A USB cable can be used to connect the VDR to a laptop to retrieve required information. The program to download the information from the VDR will be available to download on-line.
The vehicle data recorder will be capable of recording the following data via hardwired and/or CAN inputs:
Vehicle Speed - MPH
Acceleration - MPH/sec
Deceleration - MPH/sec
Engine Speed - RPM
Engine Throttle Position - % of Full Throttle
ABS Event - On/Off
Seat Occupied Status - Yes/No by Position
Seat Belt Buckled Status - Yes/No by Position
Master Optical Warning Device Switch - On/Off
Internal clock syncs the time and date when a laptop is connected Seat Belt Monitoring System
A seat belt monitoring system (SBMS) will be provided on the Command Zone ™
color display
and in the center overhead of the cab instrument panel. The SBMS will be capable of monitoring up to
10 seating positions indicating the status of each seat position per the following:
Seat Occupied & Buckled = Green LED indicator illuminated Seat Occupied & Unbuckled = Red LED indicator with audible alarm No Occupant & Buckled = Red LED indicator with audible alarm No Occupant & Unbuckled = No indicator and no alarm
FAULT = Blue LED indicator illuminated
The seat belt monitoring screen will become active on the Command Zone color display when:
The home screen is active:
and there is any occupant seated but not buckled or any belt buckled with an occupant. and there are no other Do Not Move Apparatus conditions present. As soon as all Do Not Move Apparatus conditions are cleared, the SBMS will be activated.
The SBMS will include an audible alarm that will warn that an unbuckled occupant condition exists and the parking brake is released, or the transmission is not in park. 0780137
SP
Intercom, David Clark, 5-Pos, 2-
Radio, (D,O,RPTT), 2obC, TC, 3805
INTERCOM SYSTEM
A five (
5 ) position intercom system with single radio interface capability at the driver and officer positions and remote push to talk buttons located
TBD
will be provided. Two (
2 ) outboard crew
cab positions and the tiller operator will have radio listen / intercom only.
The following David Clark components will be supplied with this system:
One (
1 ) U
3805
radio cord junction module
Two (
2 ) U
3815
Radio Interface Modules
Two (
2 ) Remote Push To Talk button kits
One (
1 ) U
3800
Intercom Module (
1 Crew)
One (
1 ) U
3802
Intercom Module (
1 ) Crew)
One (
1 ) C
3820
Power Cable
One (
1 ) U
3801
Intercom Module (Tiller)
All necessary cables and connectors
0637058
David Clark Universal Radio
Interfaces Included with Single/Dual
System
RADIO / INTERCOM INTERFACE INCLUDED
All radio interfaced stations will have universal radio interfaces installed. The interface wiring will be routed within the cab to
Motorola APX
7000
.
0589947
Headset, David Clark, H3432 Over
The Head, Flex Mic, Push On Push
Off
OVER THE HEAD HEADSET
There will be
five (
5 )
over the head headset(s) provided
each seat
.
Each David Clark, Model H
3432
, headset will feature:
5 ' Coiled cord
Noise cancelling electric microphone
Flexible microphone boom rotates
200
degrees for left or right dress
Microphone on/off button
Comfort Gel Earseals
23 dB noise reduction
0819255
Hangers For Headsets, NFPA/ULC
2024, Each
HEADSET HANGERS
There will be
five (
5 )
headset hanger(s) installed
driver's seat, officer's seat, driver's side
outboard forward facing seat, tiller operator seat and rear, center, forward facing seat . The
hanger(s) will meet the current edition of applicable NFPA and ULC standards for equipment mounting.
0835667
Install Customer Provided Two-Way
Single Remote Head Radio(s)
TWO WAY RADIO INSTALLATION
There will be
Two (
2 ) Two Way Radios
sent to the apparatus manufacturers preferred radio
installer to be installed. The transmitter(s) will be mounted Location
5 &
6 in Officers side
overhead. (Match
38759
and the remote head(s) will be mounted
Location
5 &
6 in Officers side
overhead. (Match
38759
per the shipping document.Remote heads will be recess mounted in bezels whenever possible.
Antenna whips included with the radio will be mounted to assigned NMO bases selected in other options.
Specific shipping requirements will be followed.
31 989
Bid #:
0835669
Install Customer Provided Two-Way
Dual Remote Head Radio(s)
TWO WAY RADIO INSTALLATION
There will be
Two (
2 ) Two Way Radios
sent to the apparatus manufacturers preferred radio
installer to be installed. The transmitter(s) will be mounted Behind Officers Seat (Match
38759
)
and the remote head(s) will be mounted
Officers Overhead per IP layout
Officers Overhead per IP
layout
per the shipping document.Remote heads will be recess mounted in bezels whenever possible.
Antenna whips included with the radio will be mounted to assigned NMO bases selected in other options.
Specific shipping requirements will be followed.
0835678
Install Customer Provided Handheld
Radio/Battery Charger(s)
Customer Supplied Battery Charger, Handheld Radio
There will be
Three (
3 ) Battery Chargers
located
Two (
2 ) Location - On work Surface, centered
between DS and PS directly behind dash bump out (Match
38759
) One (
1 ) In Tiller Cab (final
location TBD)
.Specific shipping instructions will be followed.
0835687
Install Customer Provided Two-Way
Radio Interface Cable
TWO WAY RADIO INTERFACE CABLE
There will be
Two (
2 ) Cables
sent to the apparatus manufacturers preferred third party installer.
Interface cable(s) to be run from
from Capt. side overhead to behind Officers seat.
to
from Capt.
side overhead to behind Officers seat.
0835790
Install Customer Provided MDT,
Complete
COMPLETE MDT INSTALLATION
There will be a customer supplied Mobile Data Terminal (MDT), docking station, mounting bracket, power supply, antenna, GPS, modem, and all cabling sent to the apparatus manufacturers preferred installer to be installed
Officers Dash, laptop dock centered in dash
recess, swing arm mount on left side of recess. Match
38759
. Power to the MDT will be
directly to
the battery power
. Specific shipping requirements will be followed.
0835872
Install Customer Provided
Cellular/WiFi Router/Modem
MOBILE RADIO MODEM INSTALLATION
There will be
one (
1 )
customer supplied modem(s) sent to the apparatus manufacturers preferred installer to be installed
Inside Center Console, below position
154
. Match
38759
.
Specific shipping requirements will be followed.This option Does not include Antenna Installation 0896881
Install, Wire, Customer Provided
Two-Way Radio Speakers,
TWO WAY RADIO SPEAKER INSTALLATION
There will be
two (
2 )
customer supplied two way radio speaker(s) sent to the apparatus manufacturers preferred third party installer.
Wiring will be provided from the speaker mounted
Match
38759
and will terminate and be
connected to the customer provided two-way radio mounted Match
38759
.
Specific shipping requirements will be followed.
0663606
SP
Install Customer Provided MDT
Cable
MDT CABLE INSTALLATION
There will be
one (
1 )
customer supplied mobile data terminal (MDT) cable(s) sent to the apparatus manufacturers preferred radio installer for installation. The cable will be run Officers
Dash, laptop dock centered in dash recess, swing arm mount on left side of recess. Match 38759
.
No other components will be installed with this option.
Specific shipping requirements will be followed.
0687904
Antenna Mount, Custom Chassis,
Cable Routed to Behind Officer Seat
RADIO ANTENNA MOUNT
There will be
three (
3 )
standard
1.125
",
18 thread antenna-mounting base(s) installed
behind
officer seat
on the cab roof with high efficiency, low loss, coaxial cable(s) routed to behind the officer seat. A weatherproof cap will be installed on the mount. 0648437
Antenna Mount, Custom Chassis,
Cable Routed to Behind Driver Seat
RADIO ANTENNA MOUNT
There will be
one (
1 )
standard
1.125
",
18 thread antenna-mounting base(s) installed
Behind
Drivers Seat. Locations on cab roof per AD drawing. Match 38759
on the cab roof with high
efficiency, low loss, coaxial cable(s) routed to behind the driver seat. A weatherproof cap will be installed on the mount.
0817058
Camera, Pierce, LS Mux, R Camera,
SD, CL714
VEHICLE CAMERA SYSTEM
There will be a color vehicle camera system provided with the following:
One (
1 ) Standard Definition (SD) camera located at the rear of the apparatus, pointing rearward, displayed automatically with the vehicle in reverse.
The camera images will be displayed on the left side vehicle information center display. Audio from the microphone on the rear camera will be
emitted by an amplified speaker with volume
control located behind the driver seat
.
The following components will be included:
One (
1 ) SV-CW
134639
CAI Camera
All necessary cables
0814831
Not Required, Camera Switcher
Camera Switcher
A camera switcher is not required.
32 989
Bid #:
0808257
SP
Camera, Pierce, 7" HD tiller Cab, RS,
LS Fwd Fcng Tiller Cam, Turn, AHD
VEHICLE CAMERA SYSTEM
There will be a color vehicle camera system provided with the following:
One (
1 ) Analog High Definition (AHD) camera located on the right side behind the rear wheels on a bracket to clear the fender crowns of the tiller trailer, pointing forward, displayed automatically when the right turn signal is activated.
One (
1 ) AHD camera located on the left side behind the rear wheels on a bracket to clear the fender crowns of the tiller trailer, pointing forward, displayed automatically when the left turn signal is activated.
There will be two (
2 )
7.00 " High Definition (HD) displays, one (
1 ) each side of the tiller cab dash
to view the respective side cameras.
The following components will be included:
Two (
2 ) HD
700136
DC, HD Displays
Two (
2 )
1080
p, AHD Side Cameras
All necessary cables
0653350
Guards, Vehicle Camera(s), Painted
Smooth Aluminum
VEHICLE CAMERA GUARDS
There will be
one (
1 )
smooth, tapered aluminum guard(s) fastened over the cab / body camera(s) located
over camera on back of tiller cab
. The guards will be painted to match the surface they
are attached to.
0896458
Pierce Command Zone, Advanced
Electronics & Control System, Vel
WiFi CZT
ELECTRICAL POWER CONTROL SYSTEM
The primary power distribution will be located forward of the officer's seating position and be easily accessible while standing on the ground for simplified maintenance and troubleshooting.
Additional electrical distribution centers will be provided throughout the vehicle to house the vehicle's electrical power, circuit protection, and control components. The electrical distribution centers will be located strategically throughout the vehicle to minimize wire length. For ease of maintenance, all electrical distribution centers will be easily accessible. All distribution centers containing fuses, circuit breakers and/or relays will be easily accessible.
Distribution centers located throughout the vehicle will contain battery powered studs for supplying customer installed equipment thus providing a lower cost of ownership.
Circuit protection devices, which conform to SAE standards, will be utilized to protect electrical circuits. All circuit protection devices will be rated per NFPA requirements to prevent wire and component damage when subjected to extreme current overload. General protection circuit breakers will be Type-I automatic reset (continuously resetting). When required, automotive type fuses will be utilized to protect electronic equipment. Control relays and solenoid will have a direct current rating of
125
percent of the maximum current for which the circuit is protected per NFPA.
Solid-State Control System
A solid-state electronics based control system will be utilized to achieve advanced operation and control of the vehicle components. A fully computerized vehicle network will consist of electronic modules,
electronic control modules to include black housings, a power indicator and status indicator
located near their point of use to reduce harness lengths and improve reliability. The control system will comply with SAE J
1939-11
recommended practices.
The control system will operate as a master-slave system whereas the main control module instructs all other system components. The system will contain patented Mission Critical software that maintains critical vehicle operations in the unlikely event of a main controller error. The system will utilize a Real Time Operating System (RTOS) fully compliant with OSEK/VDX ™
specifications providing a lower cost of ownership.
For increased reliability and simplified use the control system modules will include the following attributes:
Green LED indicator light for module power
Red LED indicator light for network communication stability status Control system self test at activation and continually throughout vehicle operation No moving parts due to transistor logic
Software logic control for NFPA mandated safety interlocks and indicators Integrated electrical system load management without additional components Integrated electrical load sequencing system without additional components Customized control software to the vehicle's configuration Factory and field programmable to accommodate changes to the vehicle's operating parameters To assure long life and operation in a broad range of environmental conditions, the solid-state control system modules will meet the following specifications:
Module circuit board will meet SAE J
771
specifications
Operating temperature from -
40 degrees Celsius to +
70 degrees Celsius (-
40 degrees Fahrenheit
to +
158
degrees Fahrenheit)
Storage temperature from -
40 degrees Celsius to +
70 degrees Celsius (-
40 degrees Fahrenheit
to +
158
degrees Fahrenheit)
Vibration to
50 g
IP
67 rated enclosure (Totally protected against dust and also protected against the effect of temporary immersion between
15 centimeters and one (
1 ) meter)
Operating voltage from eight (
8 ) volts to
32 volts DC
The main controller will activate status indicators and audible alarms designed to provide warning of problems before they become critical.
Circuit Protection and Control Diagram
Copies of all job-specific, computer network input and output (I/O) connections will be provided with each chassis. The sheets will indicate the function of each module connection point, circuit protection information (where applicable), wire numbers, wire colors and load management information.
On-Board Electrical System Diagnostics
The on-board information center will include the following diagnostic information:
Text description of active warning or caution alarms
Simplified warning indicators
Amber caution indication with intermittent alarm
Red warning indication with steady tone alarm
Advanced diagnostic feature will be provided in this control system. From the Command Zone 33 989
Bid #:
display or connected wireless device, these features allow the user to monitor the real-time status of every input or output on the vehicle. It also allows users logged in as an administrator to force on inputs or outputs to assist the troubleshooting process.
TCU Module with WiFi
An in cab module will provide WiFi wireless interface and data logging capability. The WiFi interface will comply with IEEE
802.11
b/g/n capabilities while communicating at
2.4 Gigahertz.
The module will communicate through a
black WiFi antenna
allowing a line of site communication
range of up to
300
feet with a roof mounted antenna.
The module will transmit a password protected web page to a WiFi enabled device (i.e. most smart phones, tablets or laptops) allowing two levels of user interaction. The firefighter level will allow vehicle monitoring of the vehicle and firefighting systems on the apparatus. The technician level will allow diagnostic access to inputs and outputs installed on the Command Zone ™,
control
and information system.
The TCU capability will record faults from the engine, transmission, ABS and Command Zone ™,
control and information systems as they occur. No other data will be recorded at the time the fault occurs. The data TCU will provide up to
2 Gigabytes of data storage.
The TCU will provide a means to download the TCU information and update software in the device.
Indicator Light and Alarm Prove-Out System
A system will be provided which automatically tests basic indicator lights and alarms located on the cab instrument panel.
Voltage Monitor System
A voltage monitoring system will be provided to indicate the status of the battery system connected to the vehicle's electrical load. The system will provide visual and audible warning when the system voltage is below or above optimum levels.
The alarm will activate if the system falls below
11.8 volts DC for more than two (
2 ) minutes.
Dedicated Radio Equipment Connection Points
There will be three (
3 ) studs provided in the primary power distribution center located in front of the officer for two-way radio equipment. The studs will consist of the following:
12 -volt
40 -amp battery switched power
12 -volt
60 -amp ignition switched power
12 -volt
60 -amp direct battery power
There will also be a
12 -volt
100
-amp ground stud located in or adjacent to the power distribution center.
EMI/RFI Protection
To prevent erroneous signals from crosstalk contamination and interference, the electrical system will meet, at a minimum, SAE J
551/2
, thus reducing undesired electromagnetic and radio
frequency emissions. An advanced electrical system will be used to ensure radiated and conducted electromagnetic interference (EMI) or radio frequency interference (RFI) emissions are suppressed at their source.
The apparatus will have the ability to operate in the electromagnetic environment typically found in fire ground operations to ensure clean operations. The electrical system will meet, without exceptions, electromagnetic susceptibility conforming to SAE J 1113/25
Region
1 , Class C EMR
for
10 KHz-
1 GHz to
100
Volts/Meter. The vehicle OEM, upon request, will provide EMC testing reports from testing conducted on an entire apparatus and will certify that the vehicle meets SAE J
551/2
and SAE J
1113/25
Region
1 , Class C EMR for
10 KHz-
1 GHz to
100
Volts/Meter
requirements. Component and partial (incomplete) vehicle testing is not adequate as overall vehicle design can impact test results and thus is not acceptable by itself.
EMI/RFI susceptibility will be controlled by applying appropriate circuit designs and shielding. The electrical system will be designed for full compatibility with low-level control signals and high- powered two-way radio communication systems. Harness and cable routing will be given careful attention to minimize the potential for conducting and radiated EMI/RFI susceptibility. 0896456
Prognostics, Electrical System
ELECTRICAL SYSTEM PROGNOSTICS
There will be a software based vehicle tool provided to predict remaining life of the vehicles critical fluid and events.
The system will send automatic indications to the Command Zone ™
information center and/or
wireless enabled devices to proactively alert of upcoming service intervals.
Prognostics will include the following:
Engine oil and filter
Transmission oil and filter
34 989
Bid #:
0730603
Electrical System, Velocity ESP,
Cummins, Paccar
ELECTRICAL
All
12 -volt electrical equipment installed by the apparatus manufacturer will conform to modern automotive practices. All wiring will be high temperature crosslink type. Wiring will be run, in loom or conduit, where exposed and have grommets where wire passes through sheet metal.
Automatic reset circuit breakers will be provided which conform to SAE Standards. Wiring will be color, function and number coded. Function and number codes will be continuously imprinted on all wiring harness conductors at
2.00 " intervals. Exterior exposed wire connectors will be positive locking, and environmentally sealed to withstand elements such as temperature extremes, moisture and automotive fluids.
Electrical wiring and equipment will be installed utilizing the following guidelines:
All holes made in the roof will be caulked with silicon. Large fender washers, liberally caulked, will be used when fastening equipment to the underside of the cab roof.
Any electrical component that is installed in an exposed area will be mounted in a manner that will not allow moisture to accumulate in it. Exposed area will be defined as any location outside of the cab or body.
Electrical components designed to be removed for maintenance will not be fastened with nuts and bolts. Metal screws will be used in mounting these devices. Also a coil of wire will be provided behind the appliance to allow them to be pulled away from mounting area for inspection and service work.
Corrosion preventative compound will be applied to all terminal plugs located outside of the cab or body. All non-waterproof connections will require this compound in the plug to prevent corrosion and for easy separation (of the plug).
All lights that have their sockets in a weather exposed area will have corrosion preventative compound added to the socket terminal area.
All electrical terminals in exposed areas will have silicon applied completely over the metal portion of the terminal.
All lights and reflectors, required to comply with Federal Motor Vehicle Safety Standard #108
, will
be furnished. Rear identification lights will be recessed mounted for protection. Lights and wiring mounted in the rear bulkheads will be protected from damage by installing a false bulkhead inside the rear compartments.
An operational test will be conducted to ensure that any equipment that is permanently attached to the electrical system is properly connected and in working order.
The results of the tests will be recorded and provided to the purchaser at time of delivery. 0098841
Batteries, (6) Deka Grp 31, 1000
CCA each, Threaded Stud
BATTERY SYSTEM
Six (
6 )
12 volt, Deka, Model
1231
MF, maintenance free group
31 batteries that include the
following features, each, will be provided:
1000
CCA (cold cranking amps)
185
reserve capacity
High cycle
Ref. CA of
1190
at
0 degrees Fahrenheit
185
reserve capacity
Threaded studs
0008621
Battery System, Single Start, All
Custom Chassis
BATTERY SYSTEM
There will be a single starting system with an ignition switch and starter button provided and located on the cab instrument panel.
MASTER BATTERY SWITCH
There will be a master battery switch provided within the cab within easy reach of the driver to activate the battery system.
An indicator light will be provided on the instrument panel to notify the driver of the status of the battery system.
0123174
Battery Compartment, Imp/Vel
BATTERY COMPARTMENTS
The batteries will be stored in well-ventilated compartments that are located under the cab and bolted directly to the chassis frame. The battery compartments will be constructed of 3/16
" steel
plate and be designed to accommodate a maximum of three ( 3 ) group
31 batteries in each
compartment. The compartments will include formed fit heavy-duty roto-molded polyethylene battery tray inserts with drains on each side of the frame rails. The batteries will be mounted inside of the roto-molded trays.
JUMPER STUDS
One (
1 ) set of battery jumper studs with plastic color-coded covers will be installed on the battery box on the driver's side. This will allow enough room for easy jumper cable access. 0803511
Not Required - Battery Charger
Included In Inverter/Charger Category
0814995
Not Required, Location Picked From
Location,Inverter/Battery
Charger/Conditioner
0824443
Not Required, No Ind/Remote Display
0814971
Not Required, Location Ind/Remote
35 989
Bid #:
0822831
SP
Inverter/Battery Charger, Xantrex
Frdm XC Pro 818-2010, Sw,
NonNFPA 2024 100 Amp
INVERTER / BATTERY CHARGER
There will be a Xantrex part number
818-2000
, inverter/battery charger with internal transfer relay provided.
There will be an Master on/off switch provided
in the compartment near the inverter
.
The battery charger DC output will be
100
A.
The inverter will be connected to the batteries through proper fusing and also to shoreline AC power.
An auto transfer switch will be included allowing AC loads connected to the inverter to be powered from the battery whenever shoreline AC power is not available, and the main chassis battery switch is on. If shoreline AC power is available, the battery charger function will be active and the AC loads connected.
Per NFPA
1900
,
2024
Edition
21.5.5.2 *
The alternator and/or battery system will be adequate to provide power for continuous operation for a minimum of
2 hours at full output.
Per the fire department specifications, if all DC loads on the NFPA required electrical analysis report are active, the alternator cannot provide adequate power for continuous operation for 2 hours. The apparatus will be non-compliant to NFPA
1900
standards at time of contract
execution.
Load management will be activated in low voltage situations, and the inverter will be de- energized until chassis electrical system voltage recovers. 0814986
Location, Body, Inverter/Battery
Charger, Forward Compartment, RS
The battery charger/inverter will be located in the right side forward body compartment located on
the right wall as high as practical
.
0812411
Display, Kussmaul Single Bat Status
Ind 091-94-12, Wired to Batteries
BATTERY CHARGE DISPLAY
There will be one (
1 ) Kussmaul
™,
Model
091-94-12
, universal single battery bank bar graph
display provided.
The display will read voltage direct from the battery system. 0817927
Location, Cab, Ind/Remote Display,
Driver Seat Riser, Next To w/Brkt
The Inverter/battery charger status indication/display(s) will be located next to the driver's seat area with a special bracket.
0016838
Shoreline, 30A 120V, Twist lock,
NEMA L5-30
SHORELINE
There will be
one (
1 )
30 amp
120
volt AC twist lock inlet(s) NEMA L
5-30
with gray cover(s)
provided to operate the dedicated
120
volt AC circuits on the apparatus.
The shoreline(s) will be connected to
battery charger and block heater
.
A mating connector body will also be supplied with the loose equipment.
There will be a label installed near the inlet(s) that state the following:
Line Voltage
Current Ratting (amps)
Phase
Frequency
0026800
Shoreline Location
The shoreline receptacle will be located
in the driver side lower step well of cab
.
0036802
Sub Feed Breaker Box Cutler
Hammer, For Shoreline
SUB FEED CIRCUIT BREAKER BOX (shoreline)
A Cutler Hammer sub feed box will be supplied to protect the on board circuits when an auxiliary power source is used.
The box will be installed in the
mount high on forward wall of D
9 .
The sub feed box will distribute power to specific circuits in the vehicle.
A directory for each breaker will be provided adjacent to the circuit breaker panel.
Identification of circuits will be done in a durable manner that provides years of service. 0783395
Transfer Switch, Generator to
Shoreline 30 Amp and Under
GENERATOR TO SHORELINE TRANSFER SWITCH
There will be an automatic transfer switch between the onboard generator and the shoreline inlet.
The loads connected to the transfer switch will be power from the onboard generator when the generator is running.
0647728
Alternator, 430 amp, Delco Remy
55SI
ALTERNATOR
A Delco Remy
®
, Model
55 SI, alternator will be provided. It will have a rated output current of 430
amps, as measured by SAE method J
56 . The alternator will feature an integral regulator and rectifier system that has been tested and qualified to an ambient temperature of 257
degrees
Fahrenheit (
125
degrees Celsius). The alternator will be connected to the power and ground distribution system with heavy-duty cables sized to carry the full rated alternator output. 0686615
Set Command Zone Clock To Pacific
Standard Time
36 989
Bid #:
0092582
Load Manager/Sequencer, MUX
ELECTRONIC LOAD MANAGER
An electronic load management (ELM) system will be provided that monitors the vehicles 12 -volt
electrical system, automatically reducing the electrical load in the event of a low voltage condition, and automatically restoring the shed electrical loads when a low voltage condition expires. This ensures the integrity of the electrical system.
For improved reliability and ease of use, the load manager system will be an integral part of the vehicle's solid state control system requiring no additional components to perform load management tasks. Load management systems which require additional components will not be allowed.
The system will include the following features:
System voltage monitoring.
A shed load will remain inactive for a minimum of five minutes to prevent the load from cycling on and off.
Sixteen available electronic load shedding levels.
Priority levels can be set for individual outputs.
High Idle
to activate before any electric loads are shed and deactivate with the service brake .
If enabled:
"Load Man Hi-Idle On" will display on the information center.
Hi-Idle will not activate until
30 seconds after engine start up.
Individual switch "on" indicator to flash when the particular load has been shed.
The information center indicates system voltage.
The information center, where applicable, includes a "Load Manager" screen indicating the following:
Load managed items list, with priority levels and item condition.
Individual load managed item condition:
ON = not shed
SHED = shed
SEQUENCER
A sequencer will be provided that automatically activates and deactivates vehicle loads in a preset sequence thereby protecting the alternator from power surges. This sequencer operation will allow a gradual increase or decrease in alternator output, rather than loading or dumping the entire
12 volt load to prolong the life of the alternator.
For improved reliability and ease of use, the load sequencing system will be an integral part of the vehicle's solid state control system requiring no additional components to perform load sequencing tasks. Load sequencing systems which require additional components will not be allowed.
Emergency light sequencing will operate in conjunction with the emergency master light switch.
When the emergency master switch is activated, the emergency lights will be activated one by one at half-second intervals. Sequenced emergency light switch indicators will flash while waiting for activation.
When the emergency master switch is deactivated, the sequencer will deactivate the warning light loads in the reverse order.
Sequencing of the following items will also occur, in conjunction with the ignition switch, at half- second intervals:
Cab Heater and Air Conditioning
Crew Cab Heater (if applicable)
Crew Cab Air Conditioning (if applicable)
Exhaust Fans (if applicable)
Third Evaporator (if applicable)
0783153
Headlights, Rect LED, JW Spkr Evo
2, AXT/Enf/Imp/Sab/Vel
HEADLIGHTS
There will be four (
4 ) JW Speaker®, Model
8800
,
4 " x
6 " rectangular LED lights mounted in the
front quad style, chrome housing on each side of the cab grille:
the outside light on each side will contain a part number 055
***
1 low beam module
the inside light on each side will contain a part number 055
***
1 high beam module
the
headlights to include chrome bezels
The low beam lights will be activated when the headlight switch is on.
The high beam and low beam lights will be activated when the headlight switch and the high beam switch is activated.
0840425
Light, Directional, Wln 600 Cmb, Cab
Crn, Wrp Bzl Out HD Lts, Imp/Vel
DIRECTIONAL LIGHTS
There will be two (
2 ) Whelen®
600
series, amber LED combination directional/marker lights provided. The lights will be located on the outside cab corners, one on each side next to the headlights in a
chrome trim
.
The
lens color(s) to be the same as the LEDs
.
0805325
Light, Directional, Wln M62T* LED,
15 Degree Angle Bracket, Additional
ADDITIONAL DIRECTIONAL LIGHT
There will be
two (
2 )
Whelen®, Model M
62 T*, amber LED directional lights provided
on the rear
wall of the transverse compartment on the tractor, near the kingpin . The
lens color(s) to be the
same as the LEDs
.
Each light will be surface mounted in a
15 degree angled bracket with
chrome housing
.
The flash pattern of the directional lights will be
Steady On (Arrow)
.
0620054
Light, Directional/Marker,
Intermediate, Weldon 9186-8580-29
LED 2lts
INTERMEDIATE LIGHT
There will be two (
2 ) Weldon, Model
9186-8580-29
, amber LED turn signal marker lights
furnished, one (
1 ) each side, in the rear fender panel. The light will double as a turn signal and marker light.
37 989
Bid #:
0648074
Lights, Clearance/Marker/ID, Front,
P25 LED 7 Lts
CAB CLEARANCE/MARKER/ID LIGHTS
There will be seven (
7 ) amber LED lights provided to indicate the presence and overall width of the vehicle in the following locations:
Three (
3 ) amber LED identification lights will be installed in the center of the cab above the windshield.
Two (
2 ) amber LED clearance lights will be installed, one ( 1 ) on each outboard side of the cab
above the windshield.
Two (
2 ) amber LED marker lights will be installed, one (
1 ) on each side above the cab doors.
0534987
Lights, Clearance/Marker/ID, Rear,
Truck-Lite 33050R LED 7Lts, Aerial
REAR CLEARANCE/MARKER/ID LIGHTING
There will be three (
3 ) Truck-Lite®, Model
33050
R, LED lights used as identification lights
recessed and located at the rear of the apparatus per the following:
As close as practical to the vertical centerline
Centers spaced not less than
6.00 " or more than
12.00 " apart
Red in color
All at the same height
There will be two (
2 ) Truck-Lite, Model
33050
R, LED lights recessed at the rear of the apparatus
used as clearance lights located at the rear of the apparatus per the following:
To indicate the overall width of the vehicle
One (
1 ) each side of the vertical centerline
As near the top as practical
Red in color
To be visible from the rear
All at the same height
There will be two (
2 ) Truck-Lite, Model
33050
R, LED lights recessed on the side of the apparatus
as marker lights as close to the rear as practical per the following:
To indicate the overall length of the vehicle
One (
1 ) each side of the vertical centerline
As near the top as practical
Red in color
To be visible from the side
All at the same height
There will be two (
2 ) red reflectors located on the rear of the truck facing to the rear. One ( 1 ) each
side, as far to the outside as practical, at a minimum of
15.00 ", but no more than
60.00 ", above
the ground.
There will be two (
2 ) red reflectors located on the side of the truck facing to the side. One ( 1 )
each side, as far to the rear as practical, at a minimum of
15.00 ", but no more than
60.00 ", above
the ground.
Per FMVSS
108
and CMVSS
108
requirements.
0514453
Light, Marker End Outline, Rubber
Arm, LED Marker Lamp
MARKER LIGHTS
There will be
one (
1 ) pair
of amber and red LED marker lights with rubber arm, located at the rear
of the trailer body
. The amber lens will face the front and the red lens will face the rear of the truck.
These lights will be activated with the running lights of the vehicle. 0804514
Lights, Tail, Wln M62BTT* Red
Stop/Tail & M62T* Amber Dir Arw For
Hsg
REAR FMVSS LIGHTING
The rear stop/tail and directional lighting included in the rear tail light housing will include the following:
Two (
2 ) Whelen®, Model M
62 BTT,
4.30 " high x
6.70 " wide x
1.40 " deep brake/tail lights with red
LEDs
Two (
2 ) Whelen, Model M
62 T,
4.30 " high x
6.70 " wide x
1.40 " deep directional lights with amber
LEDs. The directional lights will be set to
Steady On (Arrow)
flash pattern.
The
lens color(s) to be the same as the LEDs
.
0806466
Lights, Backup, Wln M62BU, LED,
For Tail Lt Housing
There will be two (2) Whelen Model M62BU, LED backup lights provided in the tail light housing. 0889577
Bracket, License Plate & Light, P25
LED, Stainless Brkt
LICENSE PLATE BRACKET
One (
1 ) license plate bracket constructed of stainless steel will be provided at the rear of the apparatus.
One (
1 ) white LED light with
chrome housing
will be provided to illuminate the license plate. A
stainless steel light shield will be provided over the light that will direct illumination downward, preventing white light to the rear.
0556842
Bezels, Wln, (2) M6 Chrome Pierce,
For mtg (4) Wln M6 lights
LIGHTING BEZEL
There will be two (
2 ) Whelen, Model M
6 FCV
4 P, four (
4 ) place chromed ABS housings with Pierce
logos provided for the rear M
6 series stop/tail, directional, back up, scene lights or warning lights. 0614960
SP
Instruction, Order of Tail Lt Instl,
Stop, Dir, BU,Warn
TAIL LIGHT MOUNTING INFORMATION
The following lights will be installed in the following order from the top down:
The top lights will be the stop lights/tail lights.
The second lights from the top will be the directional lights.
The third lights from the top will be the backup/scene lights.
The bottom lights will be the warning lights.
38 989
Bid #:
0589905
Alarm, Back-up Warning, PRECO
1040
BACK-UP ALARM
A PRECO, Model
1040
, solid-state electronic audible back-up alarm that actuates when the truck is shifted into reverse will be provided. The device will sound at 60 pulses per minute and
automatically adjust its volume to maintain a minimum ten ( 10 ) dBA above surrounding
environmental noise levels.
0049818
Guard, Alum Treadplate Over Lights
PROTECTIVE COVER FOR LIGHTS
There will be
eight (
8 )
aluminum treadplate cover(s) installed above the light(s) located Trailer
and cab side scene lights.
to protect them from damage.
0578264
Flash Pattern, California Title13, LED
Warning Lights
WARNING LIGHT FLASH PATTERN
The flash pattern of all the exterior warning lights will be set to meet the certified California, Title XIII flash pattern by either the light manufacturer's default flash pattern or by a conversion change to the certified flash pattern.
0658406
Light, Marker, Britax Rubber Arm,
Model 427.200.LB, Amber/Amber,
Qty/Loc
MARKER LIGHTS
There will be
one (
1 ) pair
of amber marker lights with rubber arm located
rear of D
1 and P
1 .
There will be an amber lens that faces the front and the rear of the truck.
These lights will be activated with the running lights of the vehicle. 0059809
Light, Marker, Weldon, 9186-1500
LED, Location
MARKER LIGHTS
There will be
one (
1 ) pair
of Weldon, Model:
9186-1500-10
or
9186-1500-20
, LED marker lights
installed on this apparatus, one (
1 ) light each side per the quantity selected.
These lights will be activated with the headlight switch.
These lights will be located
on top of the trailer catwalk directly above the tiller trailer axle on each side
. These lights will be installed into the rub rail or with metal flanges to protect them from most damage.
Amber lights will be used except for the rear most light at the rear of the apparatus which will be red.
0634118
SP
Mounting, Flange for Marker Type
Light, Treadplate, Pair
LIGHT MOUNTING
There will be
one (
1 )
pair of light mounting bracket(s) provided on the apparatus. Each bracket will be made from aluminum treadplate material and provide an area for a light to be mounted. It will be completely enclosed so the light will not be damaged from the back. The mounting will mount on the
centered with the rear tiller axle just below the side sheet flange so the light can be mounted shining straight up per job
27235
&#x
0 D;
.
0804537
Lights, Cornering, Tiller, Wln, 704BU,
2 lts
TILLER CORNERING LIGHTS
There will be two (
2 ) Whelen®, Model
704
BU,
3.06 " high x
7.25 " wide x
1.25 " deep lights with
white LEDs and
chrome trim
installed per the following:
one (
1 ) light will be installed on the left side body in front of the trailer axle one (
1 ) light will be installed on the right side body in front of the trailer axle The lights will be activated by the high beam function of the directional switch on the tiller cab steering column or the chassis directional light circuit. 0648630
Lights, Perimeter Cab, TecNiq E10-
WS00-1 LED 4Dr, Angled Brkt
CAB PERIMETER SCENE LIGHTS
There will be four (
4 ) TecNiq Model E
10 -WS
00-1
,
6.44 " long x
1.38 " high x
1.00 " deep
12 volt DC
weatherproof LED lights with a fabricated aluminum
45 degree brackets provided under the cab
and crew cab access areas:
One (
1 ) for the driver's access.
One (
1 ) for the passenger's side front cab access door.
One (
1 ) for the passenger's side crew cab access door.
One (
1 ) for the driver's side crew cab access door.
These lights will be activated automatically when the battery switch is on and the adjacent doors are opened or by the same means as the body perimeter lights. 0769564
Lights, Perimeter Pump House,
Amdor AY-LB-12HW020 LED 1lt
PUMP HOUSE PERIMETER LIGHTS
There will be one (
1 ) Amdor, Model AY-LB-
12 HW
020
,
350
lumens,
20.00 " LED weatherproof
strip light with bracket provided under the passenger's side pump panel running board.
If the combination of options in the vehicle does not permit clearance for a
20.00 " light, a
12.00 "
version of the Amdor light will be installed.
The light will be activated when the battery switch is on, and controlled by the same means as the body perimeter lights.
39 989
Bid #:
0888060
SP
Lights, Perimeter Body, TecNiq E10-
W000-1 4lts, Turntbl/Rr Stp, Tiller
BODY PERIMETER SCENE LIGHTS
There will be four (
4 ) TecNiq, Model E
10 -W
000-1
,
1.39 " high x
6.39 " long x
0.98 " deep lights with
white LEDs provided .
The lights will be mounted in the following locations:
One (
1 ) light will be provided under the left side turntable access steps.
One (
1 ) light will be provided under the left side tiller cab access steps.
One (
1 ) light will be provided under the right side tiller cab access steps.
One (
1 ) light will be provided under the right side turntable access steps.
The perimeter scene lights will be activated by a
a switch within reach of the driver is activated,
the parking brake is applied and a switch within reach of the tiller driver is activated .
0780173
SP
Lights, Perimeter, TecNiq E10-WS00-
1 6.39" LED
ADDITIONAL PERIMETER LIGHTS
There will be
ten (
10 )
TecNiq, Model E
10 -WS
00-1
,
1.39 " high x
6.39 " long light(s) with white
LEDs provided under
TBD
.
These additional lights will be controlled with the other body perimeter lights. 0896454
Enhanced Software for Perimeter Lts
ENHANCED SOFTWARE FOR PERIMETER LIGHTS
All perimeter lights will be deactivated when the parking brake is released unless alternate control is selected.
The cab and crew cab perimeter lights will remain on for ten ( 10 ) seconds for improved visibility
after the doors closed.
0813525
Lights, Step, P25 LED, Tiller, Control,
Trim Feature
STEP LIGHTS
There will be a total of sixteen (
16 ) white LED step lights provided for access to the tiller cab and turntable.
In order to ensure exceptional illumination, each light will provide a minimum of 25 foot-candles
(fc) covering an entire
15 " x
trim shall be chrome
15 " square placed ten (
10 ) inches below the
light and a minimum of
1.5 fc covering an entire
30 " x
30 " square at the same ten (
10 ) inch
distance below the light.
The step lights will be activated
when parking brake is applied
.
The
[Color, Trim]
.
All other steps on the apparatus will be illuminated per the current edition of applicable NFPA standards.
0693551
Lights, Tractor Scene, Wln M9LZC
LED, pair
SCENE LIGHTS
There will be one (
1 ) pair of Whelen, Model M
9 LZC, LED scene lights installed on the rear
exterior wall of the tractor cab with chrome flanges.
The lights will be controlled by the aerial master switch. 0725783
Lights, Centering, Cab Roof, Tlr,
Clpsbl, Attwood NV2002SS-7,
Red/Grn LED
CENTERING LIGHT
There will be an Attwood, Model NV
2002
SS-
7 , split red/green LED light installed with a
12.00 "
long
collapsible mast, centered on the crew cab roof. The light will be used by the tillerman to center the tiller trailer to the chassis tractor.
The light will be wired to the headlight switch.
0776357
Light, Visor, Wln, 12V P*H2* Pioneer,
Cnt Feature, 1st
12 VOLT LIGHTING
There will be
one (
1 )
Whelen® Model P*H
2 *,
17,750
lumens
12 volt DC light(s)
with a
combination of flood and spot optics
provided on the front visor,
centered
.
The housing(s)
painted parts of this light assembly to be black
.
The light(s) will be controlled
by a switch at the driver's side switch panel and by a switch at the passenger's side switch panel
.
These light(s) may be load managed when the parking brake is applied. 0727946
Lights, Wln, S30M** 30" 12VDC LED,
RS Cab, Mt Fet
12 VOLT DC SCENE LIGHTS
There will be
one (
1 )
Whelen® Model S
30 M**,
12,960
lumens
30.00 "
12 volt DC light(s) with
white LEDs provided on the right side of the cab roof located, Centered above EMS Compt, Left
Side
. The
painted parts of this light assembly to be black
. The
light(s) to be installed with
extended horizontal mounts
.
The light(s) will include the following:
Six (
6 ) scene light modules with white LEDs
Three (
3 ) amber LEDs as marker lights
Two (
2 ) additional LED modules. The
additional modules to be two (
2 ) warning light modules with
red LEDs
.
The lights will be activated per the following:
The amber marker lights
to be steady burning when the headlight switch is on
.
The scene LEDs will be controlled
by a switch at the passenger's side switch panel and by the same control that has been selected for the driver's side scene light(s) .
There will be a switch in the cab on the switch panel to control the flashing or spot LED modules.
The light(s) may be load managed when the parking brake is applied. 40 989
Bid #:
0889659
Lights, Wln, S30M** 30" 12VDC LED,
LS Cab, Mtg Fet
12 VOLT DC SCENE LIGHTS
There will be
one (
1 )
Whelen® Model S
30 M**,
9,720
lumens
2.48 " high x
30.37 " wide x
2.15 "
deep
12 volt DC light(s) with white and amber LEDs provided on the left side of the cab roof located,
Centered above EMS Compt,, Right Side
. The
painted parts of this light assembly to be
black
. The
light(s) to be installed with extended horizontal mounts .
The light(s) will include the following:
Six (
6 ) scene light modules with white LEDs
Three (
3 ) amber LEDs as marker lights
Two (
2 ) additional LED modules. The
additional modules to be two (
2 ) warning light modules with
red LEDs
.
The lights will be activated per the following:
The
marker light included in this light housing to be energized with the headlight switch .
The scene LEDs will be controlled
by a switch at the passenger's side switch panel and by the same control that has been selected for the passenger's side scene light(s) .
There will be a switch in the cab on the switch panel to control the flashing or spot LED modules.
The light(s) may be load managed when the parking brake is applied. 0898153
Lights, Wln, PSL1** Pioneer, 12
VDC, 2nd
12 VOLT LIGHTING
There will be
two (
2 )
Whelen® Model PSL
1 **,
3,150
lumens
12 volt DC LED light(s) installed on
the body located,
under driver side of the trailer body ahead and behind the trailer axle, mounted at a
45 degree angle towards the tire, the rear light to be centered below RS 1 and the forward
light at an equal distance under RS
5 from center of axle, to be used for corner
.
The
painted parts of this light assembly to be black
.
The
light(s) to be installed in a chrome
15 degree vertical recessed bracket
.
The lights will be controlled when the battery switch is on and when the Tiller Cab left directional
signal is activated, the left scene lights will activate. When the right directional signal is activated, the right scene lights will activate
.
The light(s) may be load managed when the parking brake is applied. 0748793
Lights, Wln, S44M** 44" 12VDC, RS
Body
12 VOLT LIGHTING
There will be
three (
3 )
Whelen® Model S
44 M**,
19,440
lumens
44.00 "
12 volt DC light(s) with
white LEDs provided on the right side of the body located, 1 ) Starting at front corner of RS
9 extending back (top of Cmpt.)
1 ) Starting at rear corner of RS
6 extending forward (top of Cmpt.)
1 ) Starting at aerial cradle and extending rearward, as inboard as possible . The
painted parts of
this light assembly to be black
.
The light(s) will include the following:
10 scene light modules with white LEDs
Three (
3 ) amber LEDs as marker lights
Two (
2 ) additional LED modules. The
additional modules to be two (
2 ) warning light modules with
red LEDs
.
The lights will be activated per the following:
The amber marker lights
to be steady burning when the headlight switch is on
.
The scene LEDs will be controlled
by a switch at the passenger's side switch panel, by a switch in the tiller cab and by the same control that has been selected for the passenger's side scene light (s)
.
There will be a switch in the cab on the switch panel to control the flashing warning LED modules when selected.
The light(s) may be load managed when the parking brake is applied. 0748795
Lights, Wln, S44M** 44" 12VDC, LS
Body
12 VOLT LIGHTING
There will be
three (
3 )
Whelen® Model S
44 M**,
19,440
lumens
44.00 "
12 volt DC light(s) with
white LEDs provided on the left side of the body located, 1 ) Starting at front corner of LS
7 extending back (top of Cmpt.)
1 ) Starting at rear corner of LS
4 extending forward (top of Cmpt.)
1 ) Starting at aerial cradle and extending rearward, as inboard as possible . The
painted parts of
this light assembly to be black
.
The light(s) will include the following:
10 scene light modules with white LEDs
Three (
3 ) amber LEDs as marker lights
Two (
2 ) additional LED modules. The
additional modules to be two (
2 ) warning light modules with
red LEDs
.
The lights will be activated per the following:
The amber marker lights
to be steady burning when the headlight switch is on
.
The scene LEDs will be controlled
by a switch at the passenger's side switch panel, by a switch in the tiller cab and by the same control that has been selected for the driver's side scene light(s) .
There will be a switch in the cab on the switch panel to control the flashing warning LED modules when selected.
The light(s) may be load managed when the parking brake is applied. 0766481
Lights, Wln, PSL1** Pioneer, 12
VDC, 1st
12 VOLT LIGHTING
There will be
two (
2 )
Whelen® Model PSL
1 **,
3,150
lumens
12 volt DC LED light(s) installed on
the body located,
under driver side of the trailer body ahead and behind the trailer axle, mounted at a
45 degree angle towards the tire, the rear light to be centered below LS 1 and the forward
light at an equal distance under LS
4 from center of axle, to be used for corner
.
The
painted parts of this light assembly to be black
.
The
light(s) to be installed in a chrome
15 degree vertical recessed bracket
.
The lights will be controlled when the battery switch is on and when the Tiller Cab left directional
signal is activated, the left scene lights will activate. When the right directional signal is activated, the right scene lights will activate
.
The light(s) may be load managed when the parking brake is applied. 41 989
Bid #:
0736755
Light, Wln, 12V PSL2** Slm Ln, 12
VDC 1st
12 VOLT LIGHTING ON TILLER CAB
There will be
two (
2 )
Whelen® Model PSL
2 **,
10,206
lumens
12 volt light(s) with white LEDs and
40 degree x
20 degree flood optics
. The
painted parts of this light assembly to be black
. The
light
(s) to be installed on adjustable bail bracket(s)
and located on the tiller cab,
One (
1 ) Each side of
tiller cab forward above window. Match
30972
.
The light(s) will be controlled
by a switch in the tiller cab and by a switch in a stainless steel cup located on the passenger's side at the rear of the apparatus no more than
72.00 " from the
ground
.
The light(s) may be load managed when the parking brake is applied. 0815635
SP
Light, Wln, 12V PCPSM2*, 12 VDC,
Rear Facing, Id Lts Rr Til Cab Spcl
Brkt
12 VOLT LIGHTING ON TILLER CAB
There will be one (
1 ) Whelen® Model PCPSM
2 *,
20,888
lumens
12 volt surface mount light(s)
with white LEDs,
black trim
and a combination of flood and spot optics.
The light will be located on the rear face of the tiller cab on a special fabricated bracket mounted as high as possible and centered, that will allow the rear identification lights to be installed directly above the light. The bracket will allow the light to overhang the tiller rear window without interference.
The bracket will be smooth aluminum painted to match the mounting surface.
The light will be controlled
by a switch at the passenger's side switch panel, by a switch in the tiller cab, by a switch in a stainless steel cup located on the driver's side at the rear of the apparatus no more than
72.00 " from the ground and by the same switching that has been selected for the other rear scene light(s) on the apparatus .
The light may be load managed when the parking brake is applied. 0721094
Lights, Hose Bed, Not Required, No
Hose Bed/Cargo Area
0645677
Lights, Not Required, Rear Work, Alt.
12 Volt Lights At Rear Body
0709438
Lights, Walk Surf, FRP Flood, LED
WALKING SURFACE LIGHT
There will be Model FRP,
4.00 " round black
12 volt DC LED floodlight(s) with bolt mount provided
to illuminate the entire designated walking surface on top of the body.
The light(s) will be activated when the body step lights are on. 0891094
Aerial, Tiller, Alum Body
0554269
Body Skirt Height, 18"
0040882
Tank, Water, 300 Gallon, Poly, Tiller
WATER TANK
It will have a capacity of
300
gallons and will be constructed of polypropylene plastic in a rectangular shape.
The water tank will be mounted directly above the water pump.
The joints and seams will be nitrogen welded inside and out.
The tank will be baffled in accordance with the current edition of applicable NFPA standards.
The baffles will have vent openings at both the top and bottom of each baffle to permit movement of air and water between compartments.
The longitudinal partitions will be constructed of .
38 " polypropylene plastic and extend from the
bottom of the tank through the top cover to allow positive welding.
The transverse partitions extend from
4 " off the bottom to the underside of the top cover.
All partitions interlock and will be welded to the tank bottom and sides.
The tank top will be constructed of .
50 " polypropylene.
It will be supported to keep it rigid during fast filling conditions.
Construction will include
2.00 " polypropylene dowels spaced no more than
30.00 " apart and
welded to the transverse partitions.
Two of the dowels will be drilled and tapped (.
50 " diameter,
13.00 " deep) to accommodate lifting
eyes.
A sump will be provided at the bottom of the water tank. The sump will include a drain plug and the tank outlet.
Tank will be installed in a fabricated "cradle" assembly constructed of structural steel.
A heavy duty water tank restraint will be provided.
Sufficient crossmembers are provided to properly support bottom of tank.
Crossmembers are constructed of steel bar channel or rectangular tubing.
Tank "floats" in cradle to avoid torsional stress caused by chassis frame flexing.
Rubber cushions, .
50 " thick x
3.00 " wide, will be placed on all horizontal surfaces that the tank rests on.
Stops are provided to prevent an empty tank from bouncing excessively while moving vehicle.
Tank mounting system is approved by the manufacturer.
0003405
Overflow, 4.00" Water Tank, Poly
Fill tower will be constructed of
0.50 " polypropylene and will be a minimum of
8.00 " wide x
14.00 "
long.
Fill tower will be furnished with a
0.25 " thick polypropylene screen and a hinged cover.
An overflow pipe, constructed of
4.00 " schedule
40 polypropylene, will be installed approximately
halfway down the fill tower and extend through the water tank and exit to the rear of the rear axle. 42 989
Bid #:
0028107
Not Required, Foam Cell Modification
0003429
Not Required, Direct Tank Fill
0048710
Not Required, Jet Assist
0043076
Not Required, Hose Bed, Tiller
0894249
Not Required, Tiller
0013481
Not Required, Hose Bed Capacity
0003512
Running Boards, Ascendant, PAL
RUNNING BOARDS
The running boards will be fabricated of
0.125
" bright aluminum treadplate and supported by
structural steel angle assemblies bolted to the chassis frame rails.
Running boards will be
13.00 " deep and are spaced away from the body
0.50 ".
A splash guard will be provided to keep road dirt or water from splashing up onto the pump panels.
The running boards will have a riser on the body to protect the painted surface from damage by stepping on the running boards.
The entire surface of the running boards will be covered with bright aluminum treadplate. 0825621
Turntable Steps-Morton Cass,
LS/RS, Tiller Single Axle
TURNTABLE STEPS
Steps to access the turntable from the left and right side will be provided just behind the reservoir compartment. The bottom step will have a step height not exceeding
24.00 " from the ground to
the top surface of the step at any time. All steps will have a height no greater than
14.00 " from top
surface to top surface.
The steps will be welded in place with the stepping area made of Morton Tread-Grip® channel.
The stepwell will be lined with bright aluminum treadplate to act as scuffplates.
A
knurled aluminum handrail
handrail will be provided on the forward side of the access steps. 0690023
Wall, Rear, Smooth Aluminum
SMOOTH ALUMINUM REAR WALL
The rear wall will be smooth aluminum.
0029503
Tow Eyes (2), Painted Lower Job
Color, Aerial
TOW EYES
Two (
2 ) rear painted tow eyes will be located at the rear of the apparatus and will be mounted directly to the torque box. The inner and outer edges of the tow eyes will be radiused. Each tow eye will be rated for
9000
lb and painted to match the lower job color.
43 989
Bid #:
0090670
Construction, Compt, Alum, Tiller
COMPARTMENTATION
Body and compartments will be fabricated of .
125
",
5052
-H
32 aluminum.
Side compartments will be an integral assembly with the rear fenders.
Circular fender liners will be provided for prevention of rust pockets and ease of maintenance.
Compartment flooring will be of the sweep out design with the floor higher than the compartment door lip.
The compartment door opening will be framed by flanging the edges in
1.75 " and bending out
again .
75 " to form an angle.
Drip protection will be provided above the doors by means of bright aluminum extrusion or formed bright aluminum treadplate.
The top of the compartment will be covered with bright aluminum treadplate rolled over the edges on the front, rear and outward side. These covers will have the corners welded.
Side compartment covers will be separate from the compartment tops.
All screws and bolts which protrude into a compartment will have acorn nuts on the ends to prevent injury.
A support system will be used which will incorporate a floating substructure by using Neoprene Elastomer isolators to allow the body to remain rigid while the chassis goes through its natural flex. The isolators will have a broad range of proven viability in vehicular applications, be of a fail safe design, and allow for all necessary movement in three ( 3 ) transitional and rotational modes.
This will result in a
500
lb equipment rating for each lower compartment of the body.
The compartmentation will include a
3.00 " steel support assemblies which are bolted to the chassis frame rails. A steel framework will be mounted to the body above these support assemblies connected to the support assemblies with isolators. There will be one ( 1 ) support
assembly mounted to each chassis frame rail.
AGGRESSIVE WALKING SURFACE
All exterior surfaces designated as stepping, standing, and walking areas will comply with the required average slip resistance of the current NFPA standards.
LOUVERS
All body compartments will have a minimum of one (
1 ) set of louvers stamped into a wall to
provide the proper airflow inside the compartment and to prevent water from dripping into the compartment. These louvers will be formed into the metal and not added to the compartment as a separate plate.
0632324
Compt, Single Tractor Reservoir, Lap
Door, 18" WB, Attached PH
TRACTOR RESERVOIR COMPARTMENT
A lap door compartment will be provided ahead of the tractor fifth wheel.
The left side compartment will be
17.88 " wide x
37.88 " high x
8.00 " deep with a clear door
opening of
12.00 " wide x
29.75 " high. The right side will be
17.88 " wide x
36.88 " high x
8.00 "
deep with a clear door opening of
12.00 " wide x
31.12 " high.
0683231
Compt, F/H, Trans Roll, Special
Width, 6.00" Raised, 92.00" Wide, LS
Front
LEFT SIDE COMPARTMENTATION
Left side compartmentation will consist of the following:
Two (
2 ) compartments will be provided in the front body section on the left side. Each compartment will be full-height.
The forward compartment will be approximately
24.38 " wide x
61.63 " high x
24.50 " deep with a
minimum clear door opening of approximately
16.00 " wide x
51.87 " high.
The rear compartment will be approximately
67.25 " wide x
61.63 " high x
24.50 " deep with a
minimum clear door opening of approximately
61.50 " wide x
51.87 " high.
The upper
44.75 " of each compartment will be transverse to the right side front compartmentation.
Both compartments will have roll-up doors.
0683228
Compt, F/H, Trans Front, Roll, 6.00"
Raised, LS Center, Tiller
Two (
2 ) compartments will be provided in the center body section on the left side. Each compartment will be full-height.
The forward compartment will be approximately
47.13 " wide x
61.63 " high x
24.50 " deep with a
minimum clear door opening of approximately
38.75 " wide x
51.87 " high.
The upper
44.75 " of the forward compartment will be transverse to the right side front compartmentation.
The rear compartment will be approximately
44.50 " wide x
61.63 " high x
24.50 " deep with a door
opening of approximately
39.00 " wide x
53.75 " high.
Both compartments will have roll-up doors.
0784035
SP
Cpt,Low F/D Frt Roll/Lift,Low Rr
Lap,Spc Stp,10" Rsd Fend,6" Rsd
Bd,4" Rsd Flr
Three (
3 ) compartments will be provided in the rear body section on the left side.
The forward compartment will be approximately
69.00 " wide x
34.13 " high x
24.50 " deep with a
minimum clear door opening of approximately
63.25 " wide x
26.87 " high. This compartment will
be located ahead of the rear wheels and will have a roll-up door.
There will be an upper compartment above this. The compartment will be approximately
71.75 "
wide x
15.75 " high x
13.50 " deep with a clear door opening of approximately
64.25 " wide x
9.75 "
high. This compartment will be provided with a lift-up door. The lift-up door will be provided with a cylinder that allows it to open approximately
120
degrees.
The rearward compartment will be approximately
42.00 " wide x
34.13 " high x
21.25 " deep. There
will be a section of the forward area, approximately
15.00 " from the front wall that will only be
9.00 " deep. This area will be
6.00 " wide. The clear door opening will be approximately
35.00 "
wide x
31.87 " high. This compartment will be located behind the rear wheels and in front of the tiller cab access steps and will have a double door.
The area directly behind the tiller cab access steps will be raised approximately
4.00 " from
standard to increase the rear angle of departure.
44 989
Bid #:
0683225
Compt, F/H, Trans Roll, Special
Width, 6.00" Raised, 92.00" Wide,RS
Front,Tiller
RIGHT SIDE COMPARTMENTATION
Right side compartmentation will consist of the following:
Two (
2 ) compartments will be provided in the front body section on the right side. Each compartment will be full-height.
The forward compartment will be approximately
24.13 " wide x
61.63 " high x
24.50 " deep with a
minimum clear door opening of approximately
16.00 " wide x
51.87 " high.
The rear compartment will be approximately
67.25 " wide x
61.63 " high x
24.50 " deep with a
minimum clear door opening of approximately
61.50 " wide x
51.87 " high.
The upper
44.75 " of each compartment will be transverse to the left side front compartmentation.
Both compartments will have roll-up doors.
0683224
Compt, F/H, Trans Front, Roll, 6.00"
Raised, RS Center, Tiller
Two (
2 ) compartments will be provided in the center body section on the right side. Each compartment will be full-height.
The forward compartment will be approximately
47.13 " wide x
61.63 " high x
24.50 " deep with a
minimum clear door opening of approximately
38.75 " wide x
51.87 " high.
The upper
44.75 " of the forward compartment will be transverse to the left side front compartmentation.
The rear compartment will be approximately
44.50 " wide x
61.63 " high x
24.50 " deep with a
minimum clear door opening of approximately
38.75 " wide x
51.87 " high.
Both compartments will have roll-up doors.
0784038
SP
Cpt,Low F/D Frt Roll,3 Lifts,Low Rr
Lap,Spc Stp,10" Rsd Fend,6" Rsd
Bd,4"Rsd Flr
Five (
5 ) compartments will be provided in the rear body section on the right side.
The forward low compartment will be approximately
69.00 " wide x
34.13 " high x
24.50 " deep with
a minimum door opening of approximately
63.25 " wide x
26.87 " high. This compartment will be
located ahead of the rear wheels and will have a roll-up door.
The forward upper compartment will be approximately
67.12 " wide x
15.75 " high x
13.50 " deep
with a clear door opening of approximately
59.75 " wide x
9.75 " high. This compartment will be
provided with a lift-up door.
The middle upper compartment will be approximately
64.50 " wide x
15.75 " high x
13.50 " deep
with a clear door opening of approximately
59.75 " wide x
9.75 " high. This compartment will be
provided with a lift-up door.
The rear upper compartment will be approximately
42.00 " wide x
15.75 " high x
13.50 " deep with a
clear door opening of approximately
37.25 " wide x
9.75 " high. This compartment will located in
front of the tiller cab access steps and be provided with a lift-up door.
The lift-up doors will be provided with cylinders that allows them to open approximately 120
degrees.
The rearward compartment will be approximately
42.00 " wide x
34.13 " high x
21.25 " deep in the
lower
30.13 " of height and
9.00 " deep in the remaining upper portion. There will be a section of the forward area, approximately
15.00 " from the front wall that will be only
9.00 " deep. This area
will be
6.00 " wide. The clear door opening will be approximately
35.00 " wide x
31.87 " high. This
compartment will be located directly behind the rear wheels and in front of the tiller cab access steps and have a double door.
The area directly behind the tiller cab access steps will be raised approximately
4.00 " for
increased angle of departure.
0594014
Doors, Amdor, Rollup, Side
Compartments
ROLL-UP DOOR, SIDE COMPARTMENTS
There will be
12 compartment doors
installed on the side compartments, double faced, aluminum construction,
painted one (
1 ) color to match the lower portion of the body
and manufactured by
AMDOR
™
brand roll-up doors.
Door(s) will be constructed using
1.00 " extruded double wall aluminum slats which will feature a flat smooth interior surface to provide maximum protection against equipment hang-up. The slats will be connected with a structural driven ball and socket hinge designed to provide maximum curtain diaphragm strength. Mounting and adjusting the curtain will be done with a clip system that connects the curtain to the balancer drum allowing for easy tension adjustment without tools.
The slats will be mounted in reusable slat shoes with positive snap-lock securement.
Each slat will incorporate weather tight recessed dual durometer seals. One ( 1 ) fin will be
designed to locate the seal within the extrusion. The second will serve as a wiping seal which will also allow for compression to prevent water ingression.
The doors will be mounted in a one (
1 )-piece aluminum side frame with recessed side seals to minimize seal damage during equipment deployment. All seals including side frames, top gutters and bottom panel are to be manufactured utilizing non-marring materials.
Bottom panel flange of roll-up door will be equipped with two ( 2 ) cut-outs to allow for easier
access with gloved hands.
A polished stainless steel lift bar with locking key latches to be provided for each roll-up door. The keys to be Model
751
to match all compartment and cab doors
. The lift bar will be located at the
bottom of door with striker latches installed at the base of the side frames. Side frame mounted door strikers will include support beneath the stainless steel lift bar to prevent door curtain bounce, improve bottom seal life expectancy and to avoid false door ajar signals.
All injection molded roll-up door wear components will be constructed of Type 6 nylon.
Each roll-up door will have a
3.00 inch diameter balancer/tensioner drum to assist in lifting the door.
The header for the roll-up door assembly will not exceed
4.00 ".
A heavy-duty magnetic switch will be used for control of open compartment door warning lights. 0667139
Not Req'd, Compt Blister in Front of
Rear Axle, Tiller
0067768
Not Required, Bumper, Tiller
45 989
Bid #:
0639843
SP
Scuffplate, Alum 4-Way, Rear of
Engineer's Compt, Aerial
SCUFFPLATES
The exposed rear portion of the engineer's compartment at each side will be completely covered with bright aluminum treadplate.
0650792
Scuffplate, S/S Around Air Bottle
Compt Openings, Qty
SCUFFPLATE
Two (
2 ) scuffplates
will be furnished around the opening for the air bottle compartment(s). The scuffplate(s) will be constructed of
polished stainless steel
and provided for the
on the left side
rearward of the rear wheels and on the right side rearward of the rear wheels air bottle
compartment(s).
0019845
Guard, Drip Pan, S/S, Rollup Door
DOOR GUARD
There will be
ten (
10 ) compartment doors
that will include a guard/drip pan designed to protect
the roll-up door from damage when in the retracted position and contain any water spray. The guard will be fabricated from stainless steel and installed on each roll-up door
.
0597964
Guard, Rain Drip Over Door
DRIP RAIL
There will be
two (
2 ) compartment doors
that include a rain drip designed to protect the
compartment from water damage. The guard will be fabricated from aluminum and installed above the R
1 doors
.
0505888
Keyed Locks for Latches, Lap Doors
(#751 Lock)
KEYED LOCK(S)
There will be
11 compartment doors
that require a keyed lock. The compartments to have a
keyed lock will be
RS
1 , RS
2 , RS
3 , RS
4 , RS
10 , RS
11 , B
1 , LS
1 , LS
2 , LS
8 , and LS
9 .
0028546
D-Ring Latch for Free Door, Lap
Doors
FREE DOOR D-RING LATCH
A D-ring style latch will be provided on the free door for three (
3 ) compartment doors
. The
compartmentation, to have a free door latch(es), will be RS
1 , LS
1 and B
1 .
0003919
Reverse Hinge Compartment Door
REVERSE HINGED DOOR
The
two (
2 ) compartment doors
, located on the
LS
8 and RS
10 compartment(s), will have the
hinge located opposite of the standard location.
0004010
Scuffplate, Polished S/S Bottom of
Door Frame
DOOR FRAME SCUFFPLATE
Eight (
8 ) scuffplates
will be provided for the lower door frame of
D
1 , P
1 , D
2 , , P
2 , P
3 P
4 , D
8 ,
P
10 . Each scuffplate will be polished stainless steel with a . 38 " lip down.
0004012
Scuffplate, Polished S/S, Inside Each
Compartment Door
SCUFFPLATE ON INTERIOR OF COMPARTMENT DOOR(S)
The
11 compartment doors
will include a polished stainless steel scuffplate to cover the entire width and height on the inside panel of each door pan.
Scuffplate will be located
LS
1 , RS
1 , LS
2 , RS
2 , RS
3 , RS
4 , LS
8 , LS
9 , RS
10 and RS
11 and B
1 .
0636819
Trim, Rollup Door, Painted Job Color,
by Amdor
ROLL-UP DOOR TRIM
The exterior of the aluminum trim around the door opening will be painted to match job color.
There will be
twelve (
12 )
compartments with the trim painted.
0821860
Lights, Compt, Pierce LED, Dual
Light Strips, Each Side of Door, All
Compts
COMPARTMENT LIGHTING
There will be
eighteen (
18 )
compartments with Pierce LED compartment light strips. The strips will be centered vertically along each side of the door framing. The compartments with these strip lights will be located
RS
1 , RS
2 , RS
3 , RS
4 , RS
5 , RS
6 , RS
7 , RS
8 , RS
9 , RS
10 , LS
1 , LS
2 , LS
3 ,
LS
4 , LS
5 , LS
6 , LS
7 , LS
8 ,
.
Opening the compartment door will automatically turn the compartment lighting on. 0562348
Fasteners, Mechanical, Strip Lighting
In Compartments
COMPARTMENT LIGHTING
Metal clamps will be used to retain the strip lighting in all body compartments. 0888878
SP
Shelf Tracks, Painted, Location
MOUNTING TRACKS
There will be
15 sets of tracks
for mounting shelf(s) in
RS
1 Right side of Blister, RS
6 , RS
7 , RS
8 Right of partition, RS
8 Left of partition, RS
9 , RS
11 , LS
1 , LS
3 , LS
4 , LS
5 , LS
6 Right of partition,
LS
6 Left of partition, LS
7 and LS
9 . These tracks will be installed vertically to support the adjustable shelf(s), and will be full height of the compartment. The tracks will be painted to match the compartment interior.
46 989
Bid #:
0687112
Shelves, Adjustable, 500 lb Capacity,
Full Width/Depth, Painted
ADJUSTABLE SHELVES
There will be
seven (
7 ) shelves
with a capacity of
500
lb provided. The shelf construction will
consist of .
188
" aluminum with
2.00 " sides. Each shelf will be painted spatter gray. Each shelf will be infinitely adjustable by means of a threaded fastener, which slides in a track.
The shelves will be held in place by
0.12 " thick stamped plated brackets and bolts.
The location will be
RS
1 Right of Blister, RS
6 , LS
3 , (
1 ) in LS
4 , (
2 ) in LS
6 Right of partition, (
1 ) IN
LS
7 at top of generator controls
.
0663797
Shelves, Adj Full Width, Transverse
Compartment, Painted
ADJUSTABLE SHELF
There will be
one (
1 ) shelf
with a capacity of
500
lb provided full width of the
(
1 ) in [LS
6 -RS
8 ]
attached to the right of the compartment partition, in the upper transverse area. Match 30972
.
compartment. The shelf construction will consist of
0.188
" aluminum with
2.00 " high sides.
Each shelf will be painted spatter gray.
Each shelf will be infinitely adjustable by means of a threaded fastener, which slides in a track.
The shelves will be held in place by
0.12 " thick stamped plated brackets and bolts.
0783662
SP
Shelves, Fixed, Inverted Left Side,
Transverse Compartment, Painted
SHELF
There will be
one (
1 ) shelf
with a capacity of
500
lb provided full width of the
upper portion of
RS
7 LS
5 , airbag rack to mount directly to the top of the shelf on theLS 5 side, as high as possible.
Inverted front edge on LS
5 side only.
1 " lip on RS
7 side. Match
30972
compartment. The shelf
construction will consist of
0.188
" aluminum that will be painted to match the compartment interior. On the left side there will be a
2.00 " downturned lip. On the right side there will be a
1.00 "
upturned lip.
Each shelf will be fixed mounted. Each shelf will be held in place by . 12 " thick stamped plated
brackets and bolts or angles bolted to the compartment as the engineer or shop floor see fit. 0798992
SP
Shelves, Fixed, Transverse
Compartment, Painted
SHELF
There will be
one (
1 ) shelf
with a capacity of
500
lb provided full width of the
directly above the
top of the Trimax
compartment. The shelf construction will consist of
0.188
" aluminum that will be
painted to match the compartment interior and have
2.00 " high sides.
Each shelf will be fixed mounted. Each shelf will be held in place with
0.12 " thick stamped plated
brackets and bolts or angles bolted to the compartment as the engineer or shop floor see fit. 0606445
Shelf, Adjustable, 500 lb Capacity,
1/2 Trans
HALF DEPTH ADJUSTABLE SHELF
An adjustable shelf will be provided for use in a transverse side body compartment. The shelf will be constructed of
0.188
" thick aluminum with
2.00 " high sides.
The shelf will be half depth of the transverse compartment and as wide as possible for the specified mounting location. The finish of each shelf will match that of the compartment interior.
The shelf will be secured within the compartment by means of adjustable threaded fasteners.
These fasteners will slide in an extruded aluminum track to provide height adjustment.
The shelf will have a load capacity of
500
lb.
A total of
four (
4 ) shelves
will be provided
RS
7 , LS
5 , RS
11 , LS
9 .
0009155
Tray, 500 lb, Slide-out, 1-Way, Utility,
Adj Height, 3" Sides, 1/2 Trans
ONE (
1 ) WAY SLIDE-OUT UTILITY TRAY
There will be
six (
6 ) slide-out trays
provided.
Each tray will be rated for up to
500
lb in the extended position. The tray(s) will be constructed of
0.19 " thick aluminum for the tray bottom and special aluminum extrusions for the tray sides, ends and tracks. The corners will be welded.
The tray will have
3.00 " high sides, will be half (
1/2
) depth of the transverse compartment and will
be as wide as possible for the compartment.
The tray will be supported with a minimum of six (
6 ) ball bearing rollers. The tray will slide out two
thirds (
2/3
) of its length in one (
1 ) direction.
Automatic locks will be provided for both the in and out positions. The trip mechanism for the locks will be located at the front of the tray for ease of use with a gloved hand.
The vertical location of the tray within the compartment will be adjustable.
The tray(s) will be located
Two (
2 ) in upper RS
8 ,
1 in LS
5 ,
1 in RS
7 , Two (
2 ) LS
6 .
0652268
Tray, 500 lb, Slide-out, 1-Way, Utility,
Adj Height, 3" Sides, 3/4 Trans
THREE QUARTER DEPTH SLIDE-OUT UTILITY TRAY
There will be
three (
3 ) slide-out trays
provided for use in the transverse side body compartment (s).
Each tray will be a utility style tray that is rated for up to 500
lb in the extended position. The
bottom of each tray will be constructed of
0.19 " thick aluminum while special aluminum extrusions will be utilized for the tray sides, ends and tracks. The corners will be welded. Each tray will be painted spatter gray
.
Each tray will have
3.00 " high sides, will be three quarters (
3/4
) the depth of the transverse
compartment and will be as wide as possible for the designated mounting location.
Each tray will be supported with a minimum of six (
6 ) ball bearing rollers. Each tray will slide out
two thirds (
2/3
) of its length in one (
1 ) direction only.
Automatic locks will be provided for both the in and out positions. The trip mechanism for the locks will be located at the front of each tray for ease of use with a gloved hand.
The vertical location of each tray within the compartment will be adjustable.
The tray(s) will be located
(
1 ) in RS
9 up to the partition that makes LS
7 a standard depth compt.
(
2 ) in RS
8 rear of the partition (Match
30972
)
.
47 989
Bid #:
0647045
Tray, Floor Mounted, Slide-Out, Full
Width/Full Depth, 500lb, 2.00" Sides,
2G
SLIDE-OUT FLOOR MOUNTED TRAY
There will be
five (
5 )
floor mounted slide-out tray(s) with
2.00 " sides provided. Each tray will be
rated for up to
500
lb in the extended position. The tray(s) will be constructed of a minimum . 13 "
aluminum. The finish will be
painted spatter gray
.
The trays will be designed for maximum compartment width and depth.
There will be two undermount-roller bearing type slides rated at 250
lb each provided. The pair of
slides will have a safety factor rating of
2 .
To ensure years of dependable service, the slides will be coated with a finish that is tested to withstand a minimum of
1,000
hours of salt spray per ASTM B
117
.
To ensure years of easy operation, the slides will require no more than a 50 lb force for push-in or
pull-out movement when fully loaded after having been subjected to a 40 hour vibration (shaker)
test under full load. The vibration drive file will have been generated from accelerometer data collected from a heavy truck chassis driven over rough gravel roads in an unloaded condition.
Proof of compliance will be provided upon request.
Automatic locks will be provided for both the "in" and "out" positions. The trip mechanism for the locks will be located at the front of the tray for ease of use with a gloved hand.
The location(s) will be
LS
5 , LS
6 , RS
7 , RS
8 and RS
9 .
0646559
Tray, Floor Mounted, Utility, One Way
Slide-Out, 500lb, 3" Sides, 1/2 Trans
ONE WAY UTILITY SLIDE-OUT FLOOR MOUNTED TRAY
There will be
two (
2 )
floor mounted utility slide-out tray(s) provided
LS
9 and RS
11 . Each tray will
be rated for up to
500
lb in the extended position. The tray(s) will be constructed of . 19 " thick
aluminum for the tray bottom and special aluminum extrusions for the tray sides, ends and tracks.
The corners will be welded. The finish will be
painted spatter gray
.
The tray will be
3.00 " high x half the depth of the transverse compartment x as wide as possible for the compartment.
The tray will be supported with a minimum of six (
6 ) ball bearing rollers. The tray will slide out two
thirds (
2/3
) of its length in one direction.
Automatic locks will be provided for both the "in" and "out" positions. The trip mechanism for the locks will be located at the front of the tray for ease of use with a gloved hand. 0610204
SP
Tray, Floor Mounted, Slide-Out,
500lb, 2.00" Sides, 2G, Special Width
SLIDE-OUT FLOOR MOUNTED TRAY
There will be
two (
2 )
floor mounted slide-out tray(s) with
2.00 " sides provided
LS
4 to the right of
the partition and RS
6 . The trays will be
28.00 " wide
in width and located
Match
30972
. Each tray
will be rated for up to
500
lb in the extended position. The tray(s) will be constructed of a minimum .
13 " aluminum with welded corners. The finish will be
painted spatter gray
.
There will be two undermount-roller bearing type slides rated at 250
lb each provided. The pair of
slides will have a safety factor rating of
2 .
To ensure years of dependable service, the slides will be coated with a finish that is tested to withstand a minimum of
1,000
hours of salt spray per ASTM B
117
.
To ensure years of easy operation, the slides will require no more than a 50 lb force for push-in or
pull-out movement when fully loaded after having been subjected to a 40 hour vibration (shaker)
test under full load. The vibration drive file will have been generated from accelerometer data collected from a heavy truck chassis driven over rough gravel roads in an unloaded condition.
Proof of compliance will be provided upon request.
Automatic locks will be provided for both the "in" and "out" positions. The trip mechanism for the locks will be located at the front of the tray for ease of use with a gloved hand. 0627831
Tray, Floor Mounted, Slide-Out, Full
Width/Full Depth, Low/Special Sides,
2G
SLIDE-OUT FLOOR MOUNTED TRAY
There will be
one (
1 )
floor mounted slide-out tray(s) provided
RS
8 Left of partition, ctech cabinet
will be sitting on this tray
. A capacity rating will not be available on this tray due to a reduced side height being less than
2.00 ". The tray(s) will be constructed of a minimum .
13 " aluminum with
welded corners. The finish will be
painted to match compartment interior
.
The tray(s) will be designed for maximum compartment width and depth.
The side height of the tray(s) will be as follows:
Front:
no lip
Rear:
2.00 " high
Left and Right Sides:
no lip
There will be two undermount-roller bearing type slides rated at 250
lb each provided. The pair of
slides will have a safety factor rating of
2 .
To ensure years of dependable service, the slides will be coated with a finish that is tested to withstand a minimum of
1,000
hours of salt spray per ASTM B
117
.
To ensure years of easy operation, the slides will require no more than a 50 lb force for push-in or
pull-out movement when fully loaded after having been subjected to a 40 hour vibration (shaker)
test under full load. The vibration drive file will have been generated from accelerometer data collected from a heavy truck chassis driven over rough gravel roads in an unloaded condition.
Proof of compliance will be provided upon request.
Automatic locks will be provided for both the "in" and "out" positions. The trip mechanism for the locks will be located at the front of the tray for ease of use with a gloved hand. 48 989
Bid #:
0725644
Cabinet, Drawer Assembly, CTECH,
Three Drawers, Up To 24" Wide, 24"
Deep
DRAWER ASSEMBLY
A slide-out drawer assembly will be installed
One (
1 ) Lower portion of LS
7 , One (
1 ) Lower portion
of LS
6 floor mounted Right Side of Partition. Cabinet not to exceed the height of the transverse floor of the trailer
.
The clear dimensions of the first drawer starting at the top will be
2.00 " with a face plate that is
3.00 "
high x
21.00 " deep. The clear dimensions of the second drawer will be
3.75 " with a face
plate that is
4.00 "
high x
21.00 " deep. The clear dimensions of the third drawer will be
3.75 " with a
face plate that is
4.00 "
high x
21.00 " deep. Each drawer will be the same width and not exceed
24.00 ".
The drawers will have a capacity of
250
pounds.
The drawers will be mounted in a cabinet housing constructed of light gray powder coated aluminum with anodized aluminum frames. The housing will be
24.00 " deep, and completely
enclose the drawer.
A full-length aluminum extruded rail will be provided at the top edge of each drawer. This rail will act as the latching mechanism as well as the handle for each drawer.
There will be a total of
two (
2 )
provided.
0811267
SP
Cabinet, Drawer Assembly, CTECH,
Three Drawers, Up To 24" Wide, 24"
Deep, 2nd
DRAWER ASSEMBLY
A slide-out drawer assembly will be installed
RS
8 Rear of the partition on the floor tray. Match
Job
30972
.
The clear dimensions of the first drawer starting at the top will be
2.00 " with a face plate that is
3.00 "
high x
21.00 " deep. The clear dimensions of the second drawer will be
2.75 " with a face
plate that is
3.00 "
high x
21.00 " deep. The clear dimensions of the third drawer will be
4.75 " with a
face plate that is
5.00 "
high x
21.00 " deep. Each drawer will be the same width and not exceed
24.00 ".
The drawers will have a capacity of
250
pounds.
The drawers will be mounted in a cabinet housing constructed of light gray powder coated aluminum with anodized aluminum frames. The housing will be
24.00 " deep, and completely
enclose the drawer.
A full-length aluminum extruded rail will be provided at the top edge of each drawer. This rail will act as the latching mechanism as well as the handle for each drawer.
There will be a total of
one (
1 )
provided.
0892252
SP
Toolboard, Alum, .188", Peg Board,
Add to Slide-Out Tray, Loc/Tray,
Gussetted
TOOL BOARD
An aluminum tool board will be provided.
It will be a minimum of .
188
" thick with .
20 " diameter holes in a pegboard pattern with
1.00 "
centers between holes.
A
1.00 " x
1.00 " aluminum tube frame will be welded to the edge of the board.
The board will be
mounted on adjustable tracks from front to back within the compartment and
installed
1 ) RS
9 Floor Mount Slide out tray (Adjustable track to be in first 24 " Outboard to Inboard
on a slide out tray. The board will be as high as space permits and full length of the tray. The tray is not included in this option.
The base of the toolboard will have gussets on each end of the board. The gussets at the back of the toolboard will be as wide as the back of the slide-out tray.
There will be
Two (
2 )
provided.
0726429
Partition, Vertical Compt, Transverse
Compt, Aerials/HDRs
PARTITION IN TRANSVERSE COMPARTMENT
One (
1 ) partition
will be bolted in
RS
8 /LS
6 centered to separate Drivers Side and Passenger
Side. (Match Job
309720
. Each partition will be the full vertical height of the compartment. 0726439
Partition, "L" Shaped in Compartment
"L" SHAPED PARTITION IN COMPARTMENT
One (
1 ) partition
will be bolted in
LS
7 for breaker box to face straight out of the compartment. Use partition to create a false wall to mount breaker box. There will be dead space behind the partition, L-shaped at the top to meet up with the back wall. Mount close to door. (Match Job 30972
. Each partition will be "L" shaped,
painted spatter gray
.
0726451
Partition, Vertical Compt
VERTICAL COMPARTMENT PARTITION
Two (
2 ) partitions
will be bolted in
1 ) LS
4 - (matching
30972
). LS
8 /RS
10 in essence creating a
divider between the two sides/
. Each partition will be the full vertical height of the compartment. 0635915
Mounting Plate, 3/16" Alum
MOUNTING PLATE
A quantity of
one (
1 )
3/16
" thick aluminum mounting plate(s) will be provided. The aluminum plate (s) will be
painted spatter gray to match compartment interior
. The plate(s) will be
same
dimensions as the top of the ctech cabinet
in size and mounted
in RS
8 mounted on top of the
ctech cabinet with a
1 " lip all the way around. Only as deep/wide as the ctech cabinet so that it will pull out with the ctech and the floor tray.
.
0678048
SP
False Bulkhead, Compartment
Interior
FALSE BULKHEAD INTERIOR
There will be a quantity of
one (
1 )
false bulkhead(s) provided in between the
LS
7 /RS
9 TRANSVERSE COMPT. TO MAKE LS
7 STANDARD DEPTH AND RS
9 2/3
DEPTH. Match Job
30972
compartment(s). The bulkhead will be removable with threaded fasteners and provide the maximum opening between the specified compartments. The bulkhead will be smooth aluminum and painted to match the compartment interior.
49 989
Bid #:
0828160
SP
Box, Alum 4-Way, Misc Storage, Top
Cover Only, 38"Wx19.00"Hx24"L,
Gooseneck
STORAGE BOX
A total of
two (
2 )
aluminum treadplate storage box(es) will be provided on the tiller gooseneck in the rear most outboard corner.
Each box will be approximately
38.00 " wide (front to back on the apparatus) x
19.00 " high x
24.00 " deep. The forward side of each box will be angled as needed to clear the turntable and the upper inboard portion will be angled to clear the device.
A rectangular lift up cover hinged
on the rear body side
with
D-ring latch
and pneumatic stay arm
will be provided and sized approximately
29.00 " wide x
13.50 " deep so as to be opened with the
aerial stowed.
0076795
Bracket, SCBA, Zico, ULLH, Load &
Lock, Mounted
SCBA HOLDER
A total of
four (
4 )
Ziamatic model ULLH SCBA holder bracket. This bracket will include a backplate, two seats, a footplate and the model LLS ("Load & Lock") strap to hold the bottle in the bracket. The bracket seats will be a "one size fits all" style seat and will accommodate SCBA cylinders from the high pressure
30 -minute to the high pressure
60 -minute.
The brackets will be mounted
1 - RS
9 on vertical partition on slide out tray
76795
.
0678715
Compt, At Rear Between Tow Eyes,
Smooth Alum Sngl Pan Door w/D-
Latch, Tiller
COMPARTMENT BETWEEN TOW EYES
A compartment will be supplied at the rear of the unit, above the rear bumper. It will be
8.50 "
high x
25.75 " wide x
27.00 " deep. The compartment will have a single-pan smooth aluminum drop-down door with a D-ring latch.
0832901
Mirror, Velvac, 8" Round Convex,
Each Side, Tiller Body
TILLER CONVEX MIRRORS
An
8.00 " convex mirror will be provided on each side of the tiller body TBD at Preconstruction
.
The brackets will angle outward so the tillerman can see the rear bumper in the mirrors. 0750878
SP
Webbing, Retention 2.00" Nylon
Strap, 2" Box Pattern
RETENTION WEBBING
Webbing will be provided to retain compartment equipment from laying against the compartment door. The webbing will be located
RS
5 .
The webbing will be heavy black nylon made of
2.00 " nylon strap with a
2.00 " box pattern. The
nylon webbing will be permanently fastened at the
bottom
of the compartment and have
seat belt
buckle
fasteners on the opposite side to secure it.
A total of
one (
1 )
will be provided.
0004002
Matting, .13" Rubber in Compartment
COMPARTMENT MATTING
Black rubber matting will be provided in
one (
1 )
compartments. The locations are
B
2 .
The matting will be .
13 " thick with corrugated top ribs.
0028026
Matting, Turtle Tile, Compartment
Shelving Only
MATTING, COMPARTMENT SHELVING
Turtle Tile compartment matting will be provided in
34 shelves
. The locations are,
each shelf and
tray with exception of floor mount slide tray in RS
6 .
The color of the Turtle Tile will be
black
.
0659383
Matting, Turtle Tile w/Ramp,
Compartment Floors
MATTING, COMPARTMENT FLOOR
Turtle Tile compartment matting will be provided in
13 compartments on the compartment floor.
The locations are,
RS
1 , RS
2 , RS
3 , RS
4 , RS
10 , RS
11 , LS
1 , LS
2 , LS
3 , LS
8 , LS
9 Gooseneck
Storage Box RS and Goose Neck Storage Box LS
.
The Turtle Tile will be
black
and the leading edge of the matting will include the beveled edge.
The beveled edge will be
black
.
0755526
Pegboard, Back Wall Mounted, 3/16"
Alum, Special
PEGBOARD
There will be
3/16
" thick aluminum pegboard
spatter gray painted
installed on the back wall of
one (
1 )
compartments. It will be mounted using two (
2 ) horizontal tracks. Retainers will be used to
mount the pegboard to the tracks. The holes will be
.
203
" diameter
, punched
1.00 " on center.
The pegboard will be located in the
RS
6 and mounted
Full width, upper half of backwall
.
0695412
Rack, Air Bags Inside Compartment,
2-Slot
AIR BAG STORAGE
There will be a rack installed for storing two (
2 ) air bags in the
On top of the fixed shelf in LS
5 (Match
30972
)
compartment.
The rack will be fabricated from
DA finished
.
125
" aluminum. The fire department will provide
exact sizes of air bags prior to construction. The size of the air bags will be Customer to provide
.
0796216
Floor Extension, Compartment, 1.00"
Downturned Lip
FLOOR EXTENSION
There will be a compartment floor extension provided. The floor extension will extend from the area over the frame rails to within an inch of the compartment door. The floor extension will have a
1.00 " vertical downturned lip and no return flange.
A total of
four (
4 )
will be provided and located
LS
7 , RS
9 , LS
9 and RS
11 .
50 989
Bid #:
0024016
Rub Rail, Aluminum Extruded, Side &
Rear of Body
RUB RAIL
Bottom edge of the side and rear of the body compartments will be trimmed with a bright aluminum extruded rub rail.
Trim will be
2.12 " high with
1.38 " flanges turned outward for rigidity.
The rub rails will not be an integral part of the body construction, which allows replacement in the event of damage.
0510626
Fender Crowns, Rear, S/S, Wider
Than Standard
BODY FENDER CROWNS
Stainless steel fender crowns will be provided around the rear wheel openings. These fender crowns must be wide enough to prevent splashing onto the body from the specified tires.
A rubber welting will be provided between the body and the crown to seal the seam and restrict moisture from entering.
A dielectric barrier will be provided between the fender crown fasteners (screws) and the fender sheet metal to prevent corrosion.
0626229
Handrails, Side Pump Panels, Per
Print
HANDRAILS
The handrails will be
1.25 " diameter knurled aluminum to provide a positive gripping surface.
Chrome plated end stanchions will support the handrail. Plastic gaskets will be used between end stanchions and any painted surfaces.
Drain holes will be provided in the bottom of all vertically mounted handrails.
Handrails will be provided to meet current edition of applicable NFPA standards. The handrails will be installed as noted on the sales drawing.
0558496
Handrails, Access to Tiller Cab, U-
Shaped, Knurled Aluminum, Front
Each Side
TILLER CAB HANDRAILS
A U-shaped handrail will be installed on each side of the truck on the forward side of the tiller cab access steps. The handrail will extend upward from the existing tiller cab handrail and form a U- shape approximately
10.00 " high above the top of the body. The standard handrail will be provided on the rearward side of the steps. Handrails will be
1.25 " diameter anodized aluminum
extrusion, with a knurled design, to provide a positive gripping surface.
Chrome plated end stanchions will support the handrail. Plastic gaskets will be used between end stanchions and any painted surfaces.
Drain holes will be provided in the bottom of all vertically mounted handrails. 0827906
SP
Compt, Exting (2)/O2 Bottle Fender
Panel, Tri Door, Flanged Door, Tiller
EXTINGUISHER/AIR BOTTLE/ STORAGE (Triangular)
A total of
one (
1 )
extinguisher/air bottle/storage compartments will be provided on the right side
ahead of the rear wheel
. The triangular shaped compartment will be sized to fit a
8.00 " diameter
extinguisher in the lower area and a
8.00 " diameter extinguisher as well as a
7.00 " x
5.50 " O
2 storage area in the upper area. The compartment will be approximately
25.50 " deep. A Y-shaped
partition will be provided to separate the three areas of the compartment.
Also inside the compartment,
black rubber matting
will be provided. The compartment will be
furnished with a drain hole. A
painted to match the lower body
stainless steel, triangular shaped
door with a
Southco raised trigger C
2 chrome lever latch
will be provided to contain the air
bottles. The door will have a flanged edge along the top, bottom, and side opposite the hinge.
The side that is hinged as well as the side that is curved/along the wheel well cannot be flanged.
A dielectric barrier will be provided between the door hinge, hinge fasteners and the body sheet metal.
AIR BOTTLE COMPARTMENT STRAP
A strap will be provided in the air bottle compartment(s) to help contain the bottles when the vehicle is parked on an incline. The strap will wrap around the neck and attach to the wall of the compartment.
0827967
SP
Compt, Air Pack, Fender Panel,
Flanged Door, Tiller
AIR PACK STORAGE
A quantity of
one (
1 )
air pack compartment will be provided and located
on the left side forward of
the rear wheels
. The air pack compartment(s) will be tapered to match the profile of the space available in the fender. The compartment(s) will be approximately
15.50 " wide at the top and
5.00 " wide at the bottom for the wheel cutout. The compartment(s) will be
15.50 " tall at the body
side compartment and
6.00 " tall at the wheel cutout. The compartment(s) will be
26.00 " deep and
have a drain hole.
Inside the compartment,
black Dura-Surf friction reducing material
will be provided.
A
painted to match the lower body
stainless steel hinged door with a
Southco raised trigger C
2 chrome lever latch
will be provided to contain the air pack. A dielectric barrier will be provided between the door hinge, hinge fasteners and the body sheet metal. The door will have a flanged edge along the top, bottom, and the straight edge of the side opposite the hinge. The side that is hinged as well as the side that is curved/along the wheel well cannot be flanged. 0657524
Compt, Air Bottle, Single, Round,
Fender Panel
AIR BOTTLE STORAGE (Single)
A quantity of
two (
2 ) air bottle compartments
,
7.75 " in diameter x
26.00 " deep, will be provided
on
the left side rearward of the rear wheels and on the right side rearward of the rear wheels . A
painted
stainless steel door with a
Southco raised trigger C
2 chrome lever latch
will be provided
to contain the air bottle. A dielectric barrier will be provided between the door hinge, hinge fasteners and the body sheet metal.
Inside the compartment,
black rubber matting
will be provided.
51 989
Bid #:
0785424
SP
Storage Bin, Air Bottle, Flat Mount
AIR BOTTLE STORAGE BIN
A storage bin will be provided for storage of
24 air bottles
. This storage bin will be installed
RS
5 .
Each separate air bottle storage compartment will be
7.50 " square x
23.00 " deep. The storage bin
will be formed out of aluminum and the flooring lined with Dura-surf. The storage bin will be mounted flat in order to maximize space in the specified location. 0625049
Cable Restraint, Air Bottle
Compartment Door(s)
AIR BOTTLE COMPARTMENT DOOR RESTRAINT
The
LS and RS, fender compartments ahead of trailer rear axle air bottle compartment doors will
include a cable to prevent the door from hitting another surface. There will be two (
2 )
cables
installed.
0899898
SP
Hopper, Oil Dry, Inside Compartment,
Flush Pawl Latch, 2" Door Lip
OIL DRY HOPPER
There will be an oil dry hopper installed in the
LS
4 Left of the vertical partition.
compartment. A
door will be provided on the
top
of the oil dry bin to allow refilling of the bin. The door will have a flush mount pawl latch and a
2.00 " lip at the outer edge of the door to be used as a shelf. The bin will be sized for storage of
120
lb or
20.3 gallons (
4680
cubic inch)
of clay-based oil dry
absorbent material. The hopper will have a hand valve on the bottom to control the release of the material. The absorbent material will be discharged through a PVC tube through the floor of this
compartment allowing a bucket to be placed under the truck and filled .
0004218
Ladder, 35' Duo-Safety 1200A 2-Sect
EXTENSION LADDER
There will be
one (
1 )
35 ' two (
2 ) section aluminum Duo-Safety Series
1200
-A extension ladder(s)
provided.
0010406
Ladder, 28' Duo-Safety 1200A 2-
Section
AERIAL EXTENSION LADDERS
There will be
two (
2 )
28 ' two (
2 ) section aluminum Duo-Safety Series
1200
-A extension ladder(s)
provided and located
in the aerial torque box
.
0652543
Ladder, 20' Duo-Safety 875-DR Roof
ROOF LADDER
There will be
one (
1 )
20 ' aluminum, Duo-Safety, Series
875
-DR roof ladder(s) provided.
0590849
Ladder, 14' Duo-Safety 775-DR,
16.00" Wide, Roof Hooks Both Ends,
Non-NFPA
ADDED ROOF LADDER
There will be
one (
1 )
14 ' aluminum roof, Series
775
ladder, special
16.00 " width, with roof hooks
on both ends provided.
This ladder is non compliant to NFPA
1931
, "
Standard on Design of and Design Verification Tests
for Fire Department Ground Ladders",
section
4.2.2 which states the minimum inside width
between beams for single ladders will be
16.00 ".
Per Fire Department specification request of this ladder, the apparatus will be non compliant to the current edition of applicable NFPA standards at time of contract execution. 0542436
Ladder, 16' Duo-Safety 875-DR Roof
ADDED ROOF LADDER
There will be
one (
1 )
16 ' roof, aluminum, Series
875
-DR provided.
0620443
SP
Ladder, 14' Duo-Safety 875-DR Roof,
16" Width, Non-NFPA Compliant,
Special Order
ADDED ROOF LADDER
There will be
one (
1 )
14 ' roof, aluminum, Duo-Safety, Series
875
-DR,
16 " width provided.
This ladder is non compliant to NFPA
1931
, Chapter
4.4.3.1 , "
Standard on Design of and
Design
Verification Tests for Fire Department Ground Ladders".
Per Fire Department specification request of this ladder, the apparatus will be non compliant to the current edition of applicable NFPA standards at time of contract execution. 0790929
SP
Ladder, 8' Duo-Safety 875-DR Roof
ADDED ROOF LADDER
There will be
one (
1 )
8 ' Duo-Safety Series
875
-DR aluminum roof ladder provided
on the base
section of the aerial device
.
0024233
Not Required, Attic Extension Ladder
0004246
Ladder, 10' Duo-Safety Folding, 585A
AERIAL FOLDING LADDER
There will be
one (
1 )
10 ' aluminum Duo-Safety Series
585
-A folding ladder(s) provided and
located
in the aerial torque box
.
52 989
Bid #:
0680193
Ladder Storage, Vertically Hinged
Doors, Smooth Alum, Grabber Door
Brkt, Tiller
GROUND LADDER STORAGE
The ground ladders will be removable from the center rear of the apparatus.
The ladders will be individually stored in stainless steel slides and will be arranged in such a manner that any one (
1 ) ladder can be removed without having to move or remove any other ladder. Black Dura-Surf friction reducing material will be added to the stainless steel slides, on the bottom horizontal surfaces, of the ladder storage rack.
Vertically hinged double lap doors will be provided at the rear to close the ladder compartment.
Doors will be of double pan aluminum construction. Single sheet aluminum doors will not be considered.
The lock door will be latched with Eberhard latches with "D" ring handles. There will be a Cast Products grabber door stay bracket provided on the outside of each door to hold it in the open position.
A
brushed stainless steel
scuffplate will cover the entire width and height of the inside pans of the doors.
0602102
Lights, Torque Box Ladder Storage,
Truck-Lite 44042C 2lts, LED, Round
4"
LADDER STORAGE LIGHTING
There will be two (
2 ) Truck Lite Model
44042
C,
4.00 " white LED lights with Model
40700
,
grommets used to illuminate the torque box ladder storage compartment. One ( 1 ) each side will
be located on the side wall of the torque box near the ladder storage entry area.
The lights will be activated when the ladder storage compartment door is opened. 0004251
Ladder, 8' Duo-Safety Folding, 585A
ADDITIONAL FOLDING LADDER
One (
1 )
8 ' aluminum Series
585
-A Duo-Safety folding ladder will be installed
in a U-shaped
trough inside the ladder storage compartment
.
0812235
Ladder, Little Giant, Revolution 2.0 -
Model 17, 13117
ADDITIONAL FOLDING LADDER
One (
1 ) Revolution
2.0 Model
13117
Little Giant folding ladder will be provided. The stored dimensions will be
55.50 " high x
23.75 " wide x
9.25 " deep. The weight will be
32 lbs.
The ladder will be located
rear equipment rack (Match
30972
)
.
0670839
Anti-Migration Plate, Ladders, Ladder
Storage
LADDER PLATE
A stainless plate with a two bend flange and a stainless steel hinge will be provided to secure the ladder complement. The plate assembly will be mounted to the bottom of the entrance of the ladder storage area.
When the plate is vertical, it will secure the ladders and prevent them from migrating to the rear of the apparatus.
0658169
Ladders, Nested, Left Side Ground
Ladder Storage
NESTED LADDER STORAGE
There will be nested ladders on the left side of the ladder storage compartment. The ladders will be nested so that one ladder can be removed without removing the adjoining ladder. 0658170
Ladders, Nested, Right Side Ground
Ladder Storage
NESTED LADDER STORAGE
There will be nested ladders on the right side of the ladder storage compartment. 0785724
SP
Full Enclosure, S/S, Misc. Storage, In
Torque Box, 4" W x 10' L, Cargo
Netting
ENCLOSURE IN TORQUE BOX
A stainless steel, full enclosure with an open rear will be provided in the open dead space inside
of the rear ladder storage area
in the torque box for additional storage . The enclosure will be approximately
4.00 " wide x
16.50 " high x
120
" long.
A
2.00 " black nylon webbing restraint will be provided across the rear of this enclosure. The webbing will fasten with seat belt buckles.
0725549
SP
Trough, S/S, Enclosed, Angled, w/1"
Lip
ENCLOSED S/S TROUGH w/REAR LIP
There will be
one (
1 )
stainless steel trough(s) provided in the torque box ladder storage rack Upper right side of ladder storage rack per ER drawing
. The trough(s) will be
As wide and tall as
possible
. The trough will be enclosed, including the rear (inboard) side, and provided at a slight angle towards the rear. A
1.00 " lip will be provided on the rear side to help contain equipment in the trough.
0581438
SP
Trough, Stainless Steel, Tool
Storage, In Torque Box/Ladder
Storage
ADDITIONAL TOOL STORAGE
A trough will be provided in the torque box/ladder storage area. The trough will be as high and wide as space allows and will be
10 '
long. Trough will be constructed of stainless steel and will be located
Over LS ladder storage (See ER Drawing)
0724703
Stokes Basket Storage, Trough, In
Torque Box/Ladder Compartment,
Aerial
STOKES STORAGE IN THE TORQUE BOX
Storage provisions will be provided for a stokes basket in the torque box ladder storage area. The stokes basket to be stored will be
85.00 " long x
25.00 " wide x
8.00 " high
.
53 989
Bid #:
0790949
Pike Pole, 16' DUO Safety,
Fiberglass
PIKE POLE,
16 '
One (
1 ) pike pole
16 ' long DUO Safety with a fiberglass handle, will be provided and located in
the torque box
.
0775907
Pike Pole, 12' DUO Safety,
Fiberglass
PIKE POLES
There will be
one (
1 )
12 ' Duo Safety pike pole(s) with fiberglass handles provided. The pike pole (s) will be stored in tubular holders located in the ground ladder storage compartment. 0789564
Pike Pole, 8' DUO Safety, Fiberglass,
Aerial
8 ' PIKE POLE
There will be
one (
1 )
8 ' Duo Safety pike pole(s) with fiberglass handle provided. The pike pole(s) will be stored in tubular holders located in the ground ladder storage compartment. 0549137
Not Required, Pike Pole, 6'
0548410
Not Required, Pole, Pike, 3'
0068133
Trash Hook, 8' Fire Hooks Unlimited,
TRH-8, w/D Handle
ADDITIONAL PIKE POLE(S)
There will be
one (
1 )
8 ' long trash hook(s), Fire Hooks Unlimited, Model TRH- 8 , with D handle
provided and located
Ladder Storage Compt.
.
0770464
Trough, S/S, Torque Box/Ladder
Storage, D-Handled Pike Pole/Trash
Hooks
PIKE POLE STORAGE IN TORQUE BOX/LADDER STORAGE
There will be a total of
one (
1 )
stainless steel trough(s) provided in the torque box/ladder storage area.
The trough(s) will accommodate a
Nupla fiberglass
10 ' roof vent/trash hook with D handle
.
0770572
Pike Pole Tubes, in Torque
Box/Ladder Storage, Alum, Special
Notch, NY Style
PIKE POLE STORAGE IN TORQUE BOX/LADDER STORAGE
There will be aluminum tubing provided in the torque box/ladder storage area for a total of five (
5 )
pike poles. The pike pole tube(s) will be notched to allow a New York style pike pole to fit in the tube.
If the head of a pike pole can come into contact with a painted surface, a stainless steel scuffplate will be provided.
0532882
Label, "NO STEP"
WARNING LABEL(S)
There will be
one (
1 )
label(s), indicating "NO STEP", provided
top of generator
.
54 989
Bid #:
0798010
Pump House, 47.50", Tiller, 96" Wide
Full Width Both Sides, Res Compt
Attached
PUMP COMPARTMENT
The pump compartment will be separate from the hose body and compartments so that each may flex independently of the other. It will be a fabricated assembly of steel tubing, angles and channels which supports both the fire pump and the side running boards.
The pump compartment will be mounted on the chassis frame rails with rubber biscuits in a four point pattern to allow for chassis frame twist.
Pump compartment, pump, plumbing and gauge panels will be removable from the chassis in a single assembly.
On both sides, the pump compartment will extend outward to the outside edge of the body. The area where the outlets and inlets are located will be recessed. The area above the pump inlets and outlets will be full width to support the water tank.
The reservoir compartment will be attached to the pumphouse.
PUMP MOUNTING
Pump will be mounted to a substructure which will be mounted to the chassis frame rail using rubber isolators. The mounting will allow chassis frame rails to flex independently without damage to the fire pump.
PUMP CONTROL PANELS (Side Control)
All pump controls and gauges will be located at the left (driver's) side of the apparatus and properly marked.
The pump panel on the right (passenger's) side will be removable with lift and turn type fasteners.
The left (driver's) side will be fastened with screws.
The gauge and control panels will be two (
2 ) separate panels for ease of maintenance.
The side gauge panel will be hinged at the bottom with a full length stainless steel hinge. The fasteners used to hold the panel in the upright position will be quarter-turn type. Vinyl covered cable or chains will be used to hold the gauge panel in the dropped position.
Polished stainless steel trim collars will be installed around all inlets and outlets.
All push/pull valve controls will have
1/4
turn locking control rods with polished chrome plated zinc tee handles. Guides for the push/pull control rods will be chrome plated zinc castings securely mounted to the pump panel. Push/pull valve controls will be capable of locking in any position.
The control rods will pull straight out of the panel and will be equipped with universal joints to eliminate binding.
The identification tag for each valve control will be recessed in the face of the tee handle.
All discharge outlets will have color coded identification tags, with each discharge having its own unique color. Color coding will include the labeling of the outlet and the drain for each corresponding discharge.
All line pressure gauges will be mounted in individual chrome plated castings with the identification tag recessed in the casting below the gauge. All remaining identification tags will be mounted on the pump panel in chrome plated bezels. Mounting of the castings and identification bezels will be done with a threaded peg cast on the back side of the bezel or screws. 0723555
Tiller Pump House Finish/Paint
TILLER PUMP HOUSE AREA FINISH
The tiller pump house area components will be finished as follows:
The floor of the area under the pump panel will be aluminum treadplate. The remaining interior surfaces, sides and top will be
painted lower cab color
.
The exterior surfaces of the pump house will be
painted to match lower cab
.
The water tank/cargo side sheets and area above the pump house will be smooth aluminum and
painted to match the upper cab color with a treadplate top .
The water tank top cover will be
aluminum treadplate
.
The exterior of the crosslays will be
match the upper cab color
.
0035501
Pump House Structure, Std Height
0797005
Pump, Waterous, CX, 1500 GPM,
Single Stage, Midship Split Shaft
PUMP
Fire pump will be a Waterous CX,
1500
gpm, single (
1 ) stage centrifugal type. The pump will be
an end suction, pedestal mount, single inlet type.
Pump will be the class "A" type.
Pump will deliver the percentage of rated discharge at pressures indicated below:
100
percent of rated capacity at
150
psi net pump pressure.
70 percent of rated capacity at
200
psi net pump pressure.
50 percent of rated capacity at
250
psi net pump pressure.
Pump body will be close-grained gray iron, bronze fitted.
Impeller shaft will be stainless steel, accurately ground to size. It will be supported by oil or grease lubricated, anti-friction ball bearings for rigid precise support.
Bearings will be protected from water and sediment by suitable stuffing boxes, slinger rings, and oil seals. No special or sleeve type bearings will be used. 0004482
Seal, Mechanical, Waterous
Pump will be equipped with a self-adjusting, maintenance-free, mechanical shaft seal.
The mechanical seal will consist of a flat, highly polished, spring fed carbon ring that rotates with the impeller shaft. The carbon ring will press against a highly polished stainless steel stationary ring that is sealed within the pump body.
In addition, a throttling ring will be pressed into the steel chamber cover, providing a very small clearance around the rotating shaft in the event of a mechanical seal failure. The pump performance will not deteriorate, nor will the pump lose prime, while drafting if the seal fails during pump operation.
Wear rings will be bronze and easily replaceable to restore original pump efficiency and eliminate the need to replace the entire pump casing due to wear. 55 989
Bid #:
0816447
Trans, Pump, Waterous C22 Series
PUMP TRANSMISSION
The pump transmission will be made of a three (
3 ) piece, aluminum, horizontally split casing.
Power transfer to pump will be through a high strength Morse HY-VO silent drive chain. By using a chain rather than gears,
50 percent of the sprocket will be accepting or transmitting torque, compared to two (
2 ) or three (
3 ) teeth doing all the work.
Drive shafts will be
2.35 " diameter hardened and ground alloy steel and supported by ball bearings. The case will be designed to eliminate the need for water cooling. 0635600
Pumping Mode, Stationary Only
PUMPING MODE
An interlock system will be provided to ensure that the pump drive system components are properly engaged so that the apparatus can be safely operated. The interlock system will be designed to allow stationary pumping only.
0605126
Pump Shift, Air Mnl Override, Split
Shaft, Interlocked, Waterous
AIR PUMP SHIFT
Pump shift engagement will be made by a two (
2 ) position sliding collar, actuated pneumatically
(by air pressure), with a three (
3 ) position air control switch located in the cab. A manual back-up shift control will also be located on the left side pump panel.
Two (
2 ) indicator lights will be provided adjacent to the pump shift inside the cab. One ( 1 ) green
light will indicate the pump shift has been completed and be labeled "pump engaged". The second green light will indicate when the pump has been engaged, and that the chassis transmission is in pump gear. This indicator light will be labeled "OK to pump".
The pump shift will be interlocked to prevent the pump from being shifted out of gear when the chassis transmission is in gear to meet NFPA requirements.
The pump shift control in the cab will be illuminated to meet NFPA requirements. 0003148
Transmission Lock-up, EVS
TRANSMISSION LOCK-UP
The direct gear transmission lock-up for the fire pump operation will engage automatically when the pump shift control in the cab is activated.
0004547
Auxiliary Cooling System
AUXILIARY COOLING SYSTEM
A supplementary heat exchange cooling system will be provided to allow the use of water from the discharge side of the pump for cooling the engine water. The heat exchanger will be a separate unit. It will be installed in the pump or engine compartment with the control located on the pump operator's control panel. The exchanger will be plumbed to the master drain valve. 0014486
Not Required, Transfer Valve, Single
Stage Pump
0777650
Valve, Relief Intake, Akron
PUMP INTAKE RELIEF VALVE
An Akron Style
53 relief valve will be installed on the suction side of the pump preset at 125
psig
.
The relief valve will have a working range of
50 psi to
250
psi.
The outlet will terminate below the frame rails with a
2.50 " National Standard hose thread adapter
and will have a "do not cap" warning tag.
The relief valve pressure control will be located
behind the right side pump panel with a stainless
steel access door
.
56 989
Bid #:
0721609
Controller, Pressure, Pierce LCD,
Custom Chassis
PIERCE PRESSURE CONTROLLER
A Pierce electronic pressure controller will be provided.
A pressure transducer will be installed in the discharge side of the water pump. The transducer continuously monitors pump pressure sending a signal to the electronic pressure controller.
The pressure controller can be used in two (
2 ) modes of operation, RPM mode and pressure
modes. In pump mode, the controller will be programmed to turn on/default to No Mode/Default
Press Setting
mode.
In the RPM mode, the controller can be activated after vehicle parking brake has been set. When in this mode, the controller will maintain the set engine speed, regardless of engine load (within engine operation capabilities).
In the pressure mode, the controller can be activated after the pump is engaged. When in this mode, the controller will automatically maintain the discharge pressure set by the operator (within the discharge capabilities of the pump and water supply) regardless of flow.
A
2.00 " diameter throttle control knob with no mechanical stops, a serrated grip, and a red idle push button in the center will be a integrated/part of the pressure controller. The throttle control knob will be programmed for
Clockwise
rotation to increase engine speed.
Individual LED indicators for ok to pump, throttle ready, pressure mode and rpm mode will be located on the pressure controller for easy viewing.
A pump cavitation protection feature will also be provided which will return the engine to idle should the pump cavitate. Cavitation is sensed by the combination of pump pressure below 30 psi
and engine speed above
2000
rpm for more than five (
5 ) seconds.
Other safety features include recognition of low water and no water conditions with an automatic programmed response and a push button to return the engine to idle.
The pressure controller LCD screen will be
4.20 " in size with a minimum brightness of
750
nits.
The LCD screen and LED intensity will be automatically adjust for day and nighttime operation.
The LCD screen intensity can also be manually adjusted if needed.
The following information will be provided/displayed on the LCD screen - Engine RPM
Check engine and stop engine warning indicators
Engine oil pressure
Engine coolant temperature
Water pump transmission temperature
Fuel Level
Water tank level
Battery voltage
Operating mode (RPM or pressure)
Pressure or RPM setting
On screen messaging show diagnostic and warning messages as they occur. It will show apparatus information, stored data, and program options when selected by the operator. It will monitor inputs outputs and support audible and visual warning alarms for the following conditions -
High battery voltage
Low battery voltage/engine off
Low battery voltage/engine running
High water pump temperature
Low fuel
Low engine oil pressure
High engine coolant temperature
Water tank out of water (visual alarm only)
No engine response (visual alarm only)
The pressure controller will store the accumulated operating hours for the pump and engine.
These items are to be displayed within the pressure controller menu.
The pressure controller will include a USB port on the back of the controller for easy software upgrades if needed.
0072153
Primer, Trident, Air Prime, Air
Operated
PRIMING PUMP
The priming pump will be a Trident Emergency Products compressed air powered, high efficiency, multistage venturi based AirPrime System, conforming to standards outlined in the current edition of applicable NFPA standards.
All wetted metallic parts of the priming system are to be of brass and stainless steel construction.
One (
1 ) priming control will open the priming valve and start the pump primer. 0780364
Manuals, Pump, (2) Total, Electronic
Copies
PUMP MANUALS
There will be a total of two (
2 ) pump manuals provided by the pump manufacturer and furnished with the apparatus. The manuals will be provided by the pump manufacturer in the form of two ( 2 )
electronic copies. Each manual will cover pump operation, maintenance, and parts. 0602504
Plumbing, Stainless Steel and Hose,
Single Stage Pump, Tiller
PLUMBING, STAINLESS STEEL AND HOSE
All inlet and outlet lines will be plumbed with either stainless steel pipe, flexible polypropylene tubing or synthetic rubber hose reinforced with hi-tensile polyester braid. All hose's will be equipped with brass or stainless steel couplings. All stainless steel hard plumbing will be a minimum of a schedule
10 wall thickness.
Where vibration or chassis flexing may damage or loosen piping or where a coupling is required for servicing, the piping will be equipped with victaulic or rubber couplings.
Plumbing manifold bodies will be ductile cast iron or stainless steel.
All piping lines are to be drained through a master drain valve or will be equipped with individual drain valves. All drain lines will be extended with a hose to drain below the chassis frame.
All water carrying gauge lines will be of flexible polypropylene tubing.
All piping, hose and fittings will have a minimum of a
500
PSI hydrodynamic pressure rating.
57 989
Bid #:
0089437
Plumbing Without Foam System
0004645
Inlets, 6.00" - 1250 GPM or Larger
Pump
MAIN PUMP INLETS
A
6.00 " pump manifold inlet will be provided on each side of the vehicle. The suction inlets will include removable die cast zinc screens that are designed to provide cathodic protection for the pump, thus reducing corrosion in the pump.
0004646
Cap, Main Pump Inlet, Long Handle,
NST, VLH
MAIN PUMP INLET CAP
The main pump inlets will have National Standard Threads with a long handle chrome cap.
The cap will be the Pierce VLH, which incorporates an exclusive thread design to automatically relieve stored pressure in the line when disconnected.
0084610
Valves, Akron 8000 series- All
VALVES
All ball valves will be Akron® Brass. The Akron valves will be the 8000
series heavy-duty style
with a stainless steel ball and a simple two-seat design. No lubrication or regular maintenance is required on the valve.
Valves will have a
ten (
10 ) year
warranty.
0004685
Valve, Inlet(s) - Outside Panel
Inlet valve location will be outside the pump panel.
0004700
Control, Inlet, at Valve
INLET CONTROL
The side auxiliary inlet(s) will incorporate a quarter-turn ball valve with the control located at the inlet valve. The valve operating mechanism will indicate the position of the valve. 0004660
Inlet (1), Left Side, 2.50"
LEFT SIDE INLET
There will be one (
1 ) auxiliary inlet with a
2.50 " valve at the left side pump panel, terminating with a
2.50 " (F) National Standard hose thread adapter.
The auxiliary inlet will be provided with a strainer, chrome swivel and plug. 0004680
Inlet, Right Side, 2.50"
RIGHT SIDE INLET
There will be one (
1 ) auxiliary inlet with a
2.50 " valve at the right side pump panel, terminating
with a
2.50 " (F) National Standard hose thread adapter.
The auxiliary inlet will be provided with a strainer, chrome swivel and plug. 0092569
No Rear Inlet (Large Dia) Requested
0064116
No Rear Inlet Actuation Required
0092696
Not Required, Cap, Rear Inlet
0009648
No Rear Intake Relief Valve Required
on Rear Inlet
0092568
No Rear Auxiliary Inlet Requested
0723049
Valve, .75" Bleeder, Aux. Side Inlet,
"T" Swing Handle
INLET BLEEDER VALVE
A
0.75 " bleeder valve will be provided for each side gated inlet.
The valves will be located behind the panel with a "T" swing style handle control extended to the outside of the panel.
The handles will be chrome plated and provide a visual indication of valve position. The swing handle will provide an ergonomic position for operating the valve without twisting the wrist and provides excellent leverage.
The water discharged by the bleeders will be routed below the chassis frame rails. 0014751
Tank to Pump, (1) 3.00" Valve, 3.00"
Plumbing, Reverse Linkage
TANK TO PUMP
The booster tank will be connected to the intake side of the pump with heavy duty piping and a quarter turn
3.00 " full flow line valve with the control remotely located at the operator's panel. The tank to pump line will run straight (no elbows) from the pump into the front face of the water tank and down into the tank sump. A rubber coupling will be included in this line to prevent damage from vibration or chassis flexing.
The control on the pump panel will be "in" when the valve is open and "out" when the valve is closed.
A check valve will be provided in the tank to pump supply line to prevent the possibility of "back filling" the water tank.
58 989
Bid #:
0004905
Outlet, Tank Fill, 1.50"
TANK REFILL
A
1.50 " combination tank refill and pump re-circulation line will be provided, using a quarter-turn full flow ball valve controlled from the pump operator's panel. 0062133
Control, Outlets, Manual, Pierce HW
if applicable
DISCHARGE OUTLET CONTROLS
The discharge outlets will incorporate a quarter-turn ball valve with the control located at the pump operator's panel. The valve operating mechanism will indicate the position of the valve.
If a handwheel control valve is used, the control will be a minimum of a
3.90 " diameter stainless
steel handwheel with a dial position indicator built into the center of the handwheel.
Any
3.00 inch or larger discharge valve will be a slow-operating valve to meet current edition of applicable NFPA standards.
0004940
Outlet, Left Side, 2.50"
LEFT SIDE DISCHARGE OUTLETS
Two (
2 ) discharge outlets
with a
2.50 " valve will be provided on the left side of the apparatus, terminating with a
2.50 " (M) National Standard hose thread adapter.
0005091
Elbow, Left Side Outlets, 45 Degree,
2.50" FNST x 2.50" MNST, VLH
LEFT SIDE OUTLET ELBOWS
The
2.50 " discharge outlets located on the left side pump panel will be furnished with a
2.50 " (F)
National Standard hose thread x
2.50 " (M) National Standard hose thread, chrome plated, 45 degree elbow.
The elbow will be Pierce VLH, which incorporates an exclusive thread design to automatically relieve stored pressure in the line when disconnected.
0820333
Outlet, Left Side, 2.50" w/3" Plumbing
(added)
There will be
One (
1 ) discharge outlet
with a
3.00 " valve on the left side of the apparatus,
terminating with a
2.50 " (M) National Standard hose thread adapter.
Any
3.00 inch or larger discharge valve will be a slow-operating valve in accordance with NFPA
13.7.5.3 .
0075093
Elbow, Left Side Outlets, 45 Deg,
2.50" FNST x 2.50" MNST, VLH,
Additional
ADDITIONAL LEFT SIDE OUTLET ELBOWS
The
2.50 " discharge outlets, located on the left side pump panel, will be furnished with a
2.50 " (F)
National Standard hose thread x
2.50 " (M) National Standard hose thread, chrome plated, 45 degree elbow.
The elbow will be the Pierce VLH, which incorporates an exclusive thread design to automatically relieve stored pressure in the line when disconnected.
0004945
Outlet, Right Side, 2.50"
RIGHT SIDE DISCHARGE OUTLET
One (
1 ) discharge outlet
with a
2.50 " valve will be provided on the right side of the apparatus, terminating with a
2.50 " (M) National Standard hose thread adapter.
0085096
Elbow, Right Side Outlets, 30
Degree, 2.5" FNST x 2.5" MNST,
VLH
RIGHT SIDE OUTLET ELBOWS
The
2.50 " discharge outlets, located on the right side pump panel, will be furnished with a
2.50 "
(F) National Standard hose thread x
2.50 " (M) National Standard hose thread, chrome plated, 30 degree elbow.
The elbow will be Pierce VLH, which incorporates an exclusive thread design to automatically relieve stored pressure in the line when disconnected.
0092571
Not Required, Outlets, Right Side
Additional
0089584
Not Required, Elbow, Right Side
Outlets, Additional
0816625
Outlet, Large Diameter, Right Side,
Akron Valve
LARGE DIAMETER DISCHARGE OUTLET
There will be an Akron
8800
4.00 " flat ball valve with
4.00 " plumbing
terminating with a
4.50 "
MNST chrome
adapter on the right side pump panel.
The valve will be controlled with a(n)
Pierce large handwheel with indicator
located at the pump
operator's panel.
0005097
Elbow, Large Dia Outlet, 30 Deg,
4.00" FNST x 5.00" Storz
LARGE DIAMETER OUTLET ELBOWS
The
4.00 " outlet(s) will be furnished with
one (
1 )
4.00 " (F) National Standard hose thread x
5.00 "
Storz elbow adapter with Storz cap.
0092572
Not Required, Outlet, Front
0092575
Not Required, Outlet, Rear
59 989
Bid #: