Agenda packet — Clovis City Council, July 7, 2025 (part 5 of 6)

The
12 -Bit Absolute Encoder will be an integral part of a micro-processor based control system. 79 973
Bid #:
743
AGENDA ITEM NO. 28.
0805186
Electrical System, ASL Tandem Axle,
MUX, 10/8 Cable

ELECTRICAL SYSTEM
The standard
8 conductor cable to the tip contains
10 AWG conductors.

The
107
' heavy duty ladder will utilize a microprocessor-based control system. The system will consist of the following components:

A tethered stabilizer control will be provided. The tethered control will be weatherproof and oil resistant. A Super Bright LED indicator light will be labeled on a metal photo panel for each function. The electrical connection at the tethered control will be permanently attached by a strained relieved coil cord that will allow the operator to move 14 ' away from the electrical
connection for operation.

Remote Stabilizer Controls
Weatherproof and oil resistant
One (
1 ) green "power" indicator light
One (
1 ) red "stabilizer not stowed" indicator light
One (
1 ) electric toggle switch for auto level assist
One (
1 ) electric toggle switch for the emergency power unit One (
1 ) electric toggle switch for each stabilizer to control:

Extend/retract function (front only)
Raise/lower function
One (
1 ) green "stabilizer fully extended" indicator light for each front stabilizer One (
1 ) green "firm on ground" indicator light for each stabilizer Control System Modules
Each of the control system modules will be configured as follows:

Sealed to a NEMA
4 rating
Operating range from -
40 degrees F to
185
degrees F (-
40 degrees C to
85 degrees C)
Communicate using J
1939
data link
Two (
2 ) diagnostic LED light
One (
1 ) green light that illuminates when module has power (B+) and ground One (
1 ) red light that flashes to indicate the module is capable of communicating via the data link Ground matrix identification system
The following control system modules will be used:

Control Module
Main controller for the system
USB connection allows for computer diagnostics
Power Module
Built-in fault sensing
Eight (
8 ) digital outputs
Pulse width modulating (PWM) capable
10 A continuous per output
Circuit protection based on actual current draw (not affected by heat) Constant Current Module
Built-in fault sensing
Three (
3 ) analog inputs
Eight (
8 ) digital outputs
Pulse width modulating (PWM) capable
3 A continuous per output
Circuit protection based on actual current draw (not affected by heat) Closed Loop System
Input Module
16 software selectable (digital or analog) inputs
Output Module
16 digital outputs
Input/Output Module
Eight (
8 ) software selectable (digital or analog) inputs
Eight (
8 ) digital outputs
0804781
Aerial Scene Lts Separated into
Aerial Tip Category and Aerial
Tracking Category
0803462
Lights, Tip, Wln MP** LED, 2lts

TIP LIGHT
There will be two (
2 ) Whelen® Model MP**,
5,695
lumens
12 volt DC LED lights installed at the
tip of the aerial device.

One (
1 ) will be located on the left side with
left side tip light to include narrow flood optics
.

One (
1 ) will be located on the right side with
right side tip light to include narrow flood optics
.

The
light(s) to be installed on adjustable bail bracket(s)
.

The
painted parts of this light assembly to be white
The lights will be controlled with the tracking lights. 0802753
Lights, Tracking, Wln MP** LED, 2lts

TRACKING LIGHTS
There will be two (
2 ) Whelen® MP**,
5,695
lumens
12 volt DC LED lights installed on the base
section of the aerial device below the hand rails per the following:

One (
1 ) will be located on the left side with
left side tracking light to include wide flood optics
.

One (
1 ) will be located on the right side with
right side tracking light to include wide flood optics
.

The
light(s) to be installed on adjustable bail bracket(s)
.

The
painted parts of this light assembly to be white
.

The tracking lights will be controlled by a switch located at the platform/tip and turntable
.
80 973
Bid #:
744
AGENDA ITEM NO. 28.
0653677
Lighting, Rung, LED, TecNiq, 4
Section, Base, Lower/Upper Mid, Fly

LIGHTING ON AERIAL LADDER
There will be TecNiq, Model D
02 LED rung lighting provided on both sides of the aerial ladder base, lower and upper mid, and fly sections. The lighting will be located adjacent to the ladder rungs along the lower rail of the ladder sections and will run the length of the ladder section.

The color of the sections will be:

The
base section of the ladder to be white
.

The
lower mid section of the ladder to be white
.

The
upper mid section of the ladder to be white
.

The
fly section of the ladder to be white
.

The LED rung lighting will be activated when
a switch at the turntable operator's panel is
activated through the master battery switch
.

The lights may be load managed when the parking brake is applied. 0540746
Lights, Stabilizer Warn (2) Sets, Wln
M6* LED, Colored Lens

STABILIZER WARNING LIGHTS
There will be four (
4 ) Whelen®, Model M
6 *, LED flashing warning lights with Whelen, Model
M
6 FC, chrome flanges installed, one (
1 ) on each stabilizer cover panel.

The front stabilizer pan lights will be
red
LED with a lens color the same as the LEDs
The rear stabilizer pan lights will be
red
LED with a lens color the same as the LEDs
These warning lights will be activated by the same switch as the side warning lights. 0068703
Lights, Grote Supernova LED,
Stabilizer Beam, (1) Set

STABILIZER BEAM WARNING LIGHTS
Two (
2 )

4.00 " diameter red LED flashing lights will be mounted on each stabilizer, one ( 1 ) facing
forward and one (
1 ) facing rearward. The lights will be Grote Supernova 40 series LED lights. The
lights will be recessed in the horizontal beam of the stabilizer. These warning lights will be activated with the aerial master switch.
0762388
Lights, Stabilizer Scene, (2) sets,
Amdor AY-LB-12HW012, LED

STABILIZER SCENE LIGHTS
There will be one (
1 ) Amdor®, Model AY-LB-
12 HW
012
,
190
lumen,
12 " long, white LED strip light
installed under each stabilizer beam to illuminate the surrounding area. A total of four ( 4 ) lights
will be installed. The lights will be activated by the aerial master switch. 0783034
DC Power To Aerial Tip, 13.92 Amps
@ 12 Volt DC, ASL
DC POWER CABLE to TIP
There will be a cable installed in the aerial device to provide

13.92 amps @
12 volts DC to the tip
of the aerial device.
0736393
Intercom, 3-Way Fire Research
ICA910 Hands Free
3 -WAY AERIAL COMMUNICATION SYSTEM
There will be a Fire Research model ICA
910
three-way intercom system provided. There will be
two (
2 ) control modules located, one (
1 ) at the turntable operator console and one (
1 ) at the
pump panel. Each control module will have and an LED volume display and push-button volume control. A hands free module will be located at the aerial tip or platform and constantly transmit to the other module unless the push-to-talk button is pressed.

Each intercom unit will be weatherproof.
0540895
Not Required, Breathing Air to Tip,
Aerial Ladder
0024742
Not Required, Mask, Breathing Air To
Tip
0786456
Raised Pedestal, 8.00", Ascendant
Tandem, AXT/Velocity

RAISED AERIAL PEDESTAL
The aerial pedestal will be raised to accommodate the height of the cab. 0808215
LyfePulley, Rescue System

RESCUE LIFTING SYSTEM
A rescue lifting attachment will be provided. The lifting attachment will mount to the aerial
egress and will consist of a pair of nylatron pulleys mounted to a stainless steel shaft. The pulleys will be adjustable from side to side and will have a total lifting capacity of 750
lb,
regardless of whether one (
1 ) or both pulleys are being utilized.
0604457
Lifting Eye Assembly, Rope Rescue
Attachment, ASL, LSL

LIFTING EYE ASSEMBLY - ROPE RESCUE ATTACHMENT
A lifting eye assembly will be provided that is designed to evenly distribute load at the tip of the aerial. The lift eye assembly is retained by two (
2 ) locking pins, one (
1 ) at each end outboard side
of the egress. Leveling is maintained by the lifting eye assembly rotating within the egress mounting. The lifting eye assembly rating will match the capacity rating of the aerial device. 81 973
Bid #:
745
AGENDA ITEM NO. 28.
0827073
SP
Rope Tie Bar At Base,Painted
Box,Rescue Lifting Syst,w/Harken
LokHead 500 Winch

ROPE TIE BAR AT BASE SECTION, RESCUE LIFTING SYSTEM WITH WINCH A removable bracket will be supplied at the rear of the base section, attached between the left hand and right hand rear hand rails. The bracket will provide Lyfe Pulley rope tie off and/or guide points centered between the rear hand rails. The bracket will be designed to be easily removable and not interfere with a fully retracted ladder assembly when attached to the base section. A storage box for the bracket will be provided on the outside rear of the base section. The storage box and bracket will be painted to match the aerial device.

There will be a Harken Lokhead Rigging Winch
500
with handle provided and mounted directly to
the top of the removable bracket and centered between the rope tie off eyes. The winch will be rated for a
750
lb maximum load that will allow straight or horizontal side pulls only. A label will be provided near the winch to indicate the
750
lb maximum load.
0694277
Kit, Aerial Device Lubrication

AERIAL LUBRICATION KIT
There will be a kit provided to lubricate the aerial device. The kit will include a 5 gallon pail of
synthetic grease, plastic gloves, paint suits, varnish brushes, and safety glasses. A storage container with lid will be provided to store the gloves, paint suits, brushes and glasses. 0530826
Turntable Access, ManSaver Bars,
Yellow

AERIAL TURNTABLE MANSAVER
™
BARS
Yellow ManSaver
™

bars will be installed at the aerial turntable.
0624672
Waterway, High Flow, 1500 GPM,
ASL

WATER SYSTEM
A waterway system will be provided consisting of the following components and features:

5.00 " pipe will be connected to the water supply on one end and to a

5.00 " internal diameter
water swivel at the rotation point of the turntable. The water swivel will permit 360
degree
continuous rotation of the aerial device.

The

5.00 " waterway swivel is to be routed through the rotation point up to the heel pin swivel. The heel pin swivel will allow the water to flow to the ladder pipe while elevating the aerial ladder from -
10 degrees to
77 degrees. The heel pivot pin is not integral with the waterway swivel at any point. The design of the waterway will allow complete servicing of the waterway swivel without disturbing the heel pivot pin.

The integral telescopic water system will consist of a

4.50 " diameter tube in the base section, a

4.00 " diameter tube in the inner mid-section, a

3.50 " diameter tube in the outer mid-section, and a

3.00 " diameter tube in the fly section. The telescopic waterway will be constructed of anodized aluminum pipe.

The aerial will be capable of discharging up to
1000
gpm at
100
psi parallel to the ladder and
90 degrees to each side of center while maintaining the rated tip load.

The aerial will be capable of discharging between
1001
and up to
1500
gallons per minute at
100

psi parallel to the ladder and
40 degrees to each side of center while maintaining the rated tip load.

The master stream will be capable of flow up to
30 degrees above horizontal.

An adjustable pressure relief valve will be furnished to protect the aerial waterway from a pressure surge.

1.50 " drain valve will be located at the lowest point of the waterway system.

WATERWAY SEALS
The waterway seals will be of type-B PolyPak design, composed of nitroxile seal and a nitrile wiper, which together offer maximum stability and extrusion resistance on the waterway. The seal will be capable of withstanding pressures up to
2000
psi, temperatures in excess of
250
degrees
Fahrenheit and have resistance to all foam generating solutions. The seals will be internally lubricated.

The waterway seals will have automatic centering guides constructed of synthetic thermalpolymer. The guides will provide positive centering of the extendible sections within each other and the base section to insure longer service life and smoother operation. 0603173
Monitor, TFT Typhoon Y5-EB1A-L302
Electric, w/Extended Vertical Travel

AERIAL MONITOR
A Task Force Tips Model Y
5 -EB
1 A-L
302
monitor with stow will be provided at the tip with a
TFT
1250
gpm Model M-ERP
1250
. This monitor will allow for an additional
30 degrees of travel above
horizontal at the aerial tip.

The monitor's functions will be controlled electrically from two ( 2 ) separate locations. One (
1 )
control will be located at the control console and the other at the ladder tip.

If the aerial has a quick-lock waterway, a limit switch will be provided to disable the extended vertical travel when the monitor is locked to the lower ladder section.

There will be a courtesy light at the tip of the aerial to illuminate the controls. 0609404
Wireless Monitor Remote Control,
TFT YE-RF-900-D, with Display

WIRELESS REMOTE AERIAL MONITOR CONTROL
One (
1 ) wireless remote will be provided near the pump operator's panel in a protected area. The remote control will include a display for advanced system feedback and backlit control panel for improved visibility.
0010758
Flow Meter, Waterway, PAL, 110'
Ascendant, MUX

AERIAL WATERWAY FLOW METER
Waterway flow, including total water flowed, will be monitored by the microprocessor. An LCD display will be located at the turntable control station. 0004836
Inlet, 5.00" at Rear w/ Pump,
Ascendant Tandem, PAP, PAL

REAR INLET
A

5.00 " NST inlet to the aerial waterway will be provided at the rear of the apparatus. It will be furnished with a

5.00 " chrome plated adapter and a

5.00 " chrome plated, long handle cap.
82 973
Bid #:
746
AGENDA ITEM NO. 28.
0673128
Quick-Lock Waterway Locking
System, 100' HDL, 105' HDL, ASL

WATERWAY LOCKING SYSTEM
The aerial ladder waterway monitor will be capable of being positioned at either the fly section or at the next lower section of the ladder.

The monitor location will be changeable by the use of a single handle, located at the side of the ladder.

The handle, attached to a cam bracket, will simply be moved forward to lock the monitor at the fly section and back to lock it to the previous section.

There will be no pins to remove and reinstall.

The monitor will be operational at all times, regardless of its position, without connecting or disconnecting electrical lines.
0772264
SP
Adapter, Aerial Inlet, 5" FNST x 4.5"
MNST w/Cap

AERIAL INLET ADAPTER
There will be
one (
1 )

5.00 " FNST x

4.50 " MNST adapter with blind cap provided on the aerial inlet.
0518550
Outlet, 2.50" Auxiliary, LHS, Aerial Tip

2.50 " AUXILIARY OUTLET AT AERIAL TIP
An auxiliary hose connection outlet will be supplied at the tip of the aerial ladder. It will be located on the left hand side of the aerial waterway.

Flow to the auxiliary outlet will be supplied by

2.50 " piping. A

2.50 " gate valve with a non-rising
stem and crank handle will be supplied. A cap and chain will be provided.

Flow to the aerial waterway monitor will be controlled by a

4.00 " aluminum butterfly valve with a
handwheel. The valve will be located at the monitor inlet.

A
200
psi relief valve and a

0.75 " automatic drain valve will be supplied in the waterway at the tip. 0047897
Tools, Aerial

TOOLS
The following tools will be provided for retorquing of all specified bolts as recommended by the manufacturer:

Torque Wrench
All Required Extensions, Sockets and Adapters
4 -to-
1 Multiplier
0668583
Manuals and Training, 4 Consecutive
Days, Ascendant Ladder, PAL

MANUALS
Two (
2 ) operator maintenance manuals and two (
2 ) wiring diagrams pertaining to the aerial
device will be provided with the apparatus at time of pick-up.

INITIAL INSTRUCTION
On initial delivery of the fire apparatus, the contractor will supply a qualified representative to demonstrate the apparatus and provide initial instruction to the fire department regarding the operation, care, and maintenance of the apparatus for a period of four ( 4 ) consecutive days.
0007150
Bag of Nuts and Bolts

LOOSE EQUIPMENT
The following equipment will be furnished with the completed unit:

One (
1 ) bag
of chrome, stainless steel, or cadmium plated screws, nuts, bolts and washers, as used in the construction of the unit.
83 973
Bid #:
747
AGENDA ITEM NO. 28.
0816502
NFPA Required Loose Equipment,
Quint, NFPA/ULC 2024, Provided by
Fire Dept

NFPA LOOSE EQUIPMENT
NFPA Required Loose Equipment Provided by Fire Department The following loose equipment as outlined in NFPA
1900
,
2024
edition, table

8.1 and CAN/ULC
S
515:2024
edition, section

5.2 will be provided by the fire department:

One (
1 ) traffic vest for each seating position, each vest to comply with ANSI/ISEA 107
,
American
National Standard for High-Visibility Safety Apparel and Accessories , and have a five-point
breakaway feature that includes two (
2 ) at the shoulders, two (
2 ) at the sides, and one (
1 ) at the
front.

Five (
5 ) fluorescent orange traffic cones not less than

28.00 " (
711
mm) in height, each equipped
with a

6.00 " (
152
mm) retro-reflective white band no more than

4.00 " (
152
mm) from the top of
the cone, and an additional

4.00 " (
102
mm) retro-reflective white band

2.00 " (
51 mm) below the

6.00 " (
152
mm) band.

Five (
5 ) illuminated warning devices such as highway flares, unless the five ( 5 ) fluorescent
orange traffic cones have illuminating capabilities.

Four (
4 ) ladder belts meeting the requirements of NFPA
2500
.

NFPA Loose Equipment That Should be Considered
The following loose equipment as outlined in NFPA
1900
,
2024
edition, appendix table A.

8.4 (a)
and CAN/ULC S
515:2024
edition, section

5.2 should be considered:
800
ft (
240
m) of

2.50 " (
65 mm) or larger fire hose
400
ft (
120
m) of

1.50 " (
38 mm),

1.75 " (
45 mm), or

2.00 " (
52 mm) fire hose
One (
1 ) handline nozzle,
200
gpm min
Two (
2 ) handline nozzles,
95 gpm min
One (
1 ) playpipe with shutoff and
1 ",

1.125
", and

1.25 " tips
Four (
4 ) SCBA apparatus
Four (
4 ) SCBA spare cylinders
One (
1 ) first aid kit.

Four (
4 ) salvage covers, each a minimum size of
12 ft ×
18 ft (

3.6 m ×

5.5 m).

Four (
4 ) combination spanner wrenches.

Two (
2 ) hydrant wrenches.

One (
1 ) double female

2.50 " adapter with national hose (NH) thread.

One (
1 ) double male

2.50 " adapter with national hose (NH) thread.

One (
1 ) rubber mallet, suitable for use on suction hose connections.

One (
1 )
150
ft (
45 m) light-use life safety rope meeting the requirements of NFPA 2500
.

One (
1 )
150
ft (
45 m) general-use life safety rope meeting the requirements of NFPA 2500
.

One (
1 ) automatic external defibrillator (AED).
0816941
Soft Suction Hose, Provided by Fire
Department, NFPA/ULC 2024

SOFT SUCTION HOSE PROVIDED BY FIRE DEPARTMENT
Hose is not on the apparatus as manufactured. The fire department will provide suction or supply hose.
0027023
No Strainer Required
0816939
Extinguisher, Dry Chemical, NFPA
2024, Provided by Fire Department

DRY CHEMICAL EXTINGUISHER PROVIDED BY FIRE DEPARTMENT
The extinguisher is not on the apparatus as manufactured. The fire department will provide and mount the extinguisher.
0816937
Extinguisher, 2.5 Gal. Pressurized
Water, NFPA/ULC 2024, Provided by
Fire Dept

WATER EXTINGUISHER PROVIDED BY FIRE DEPARTMENT
The extinguisher is not on the apparatus as manufactured. The fire department will provide and mount the extinguisher.
0007482
Not Required, Crowbars

0007484
Not Required, Claw Tools

0816998
Axe, Flathead, Provided by Fire
Department

FLATHEAD AXE PROVIDED BY FIRE DEPARTMENT
The axe is not on the apparatus as manufactured. The fire department will provide and mount the axe.
0817000
Axe, Pickhead, Provided by Fire
Department

PICKHEAD AXE PROVIDED BY FIRE DEPARTMENT
The axe is not on the apparatus as manufactured. The fire department will provide and mount the axe.
0007494
Not Required, Sledgehammers

84 973
Bid #:
748
AGENDA ITEM NO. 28.
0741569
Paint Process / Environmental
Requirements, Appleton

PAINT PROCESS
The exterior custom cab and body painting procedure will consist of a seven ( 7 ) step finishing
process as follows:

Manual Surface Preparation
- All exposed metal surfaces on the custom cab and body will be thoroughly cleaned and prepared for painting. Imperfections on the exterior surfaces will be removed and sanded to a smooth finish. Exterior seams will be sealed before painting. Exterior surfaces that will not be painted include; chrome plating, polished stainless steel, anodized aluminum and bright aluminum treadplate.

Chemical Cleaning and Pretreatment
- All surfaces will be chemically cleaned to remove dirt, oil, grease, and metal oxides to ensure the subsequent coatings bond well. The aluminum surfaces will be properly cleaned and treated using a high pressure, high temperature 4 step Acid Etch
process. The steel and stainless surfaces will be properly cleaned and treated using a high temperature
3 step process specifically designed for steel or stainless. The chemical treatment converts the metal surface to a passive condition to help prevent corrosion.

Surfacer Primer
- The Surfacer Primer will be applied to a chemically treated metal surface to provide a strong corrosion protective basecoat. A minimum thickness of 2 mils of Surfacer Primer
is applied to surfaces that require a Critical aesthetic finish. The Surfacer Primer is a two- component high solids urethane that has excellent sanding properties and an extra smooth finish when sanded.

Finish Sanding
- The Surfacer Primer will be sanded with a fine grit abrasive to achieve an ultra- smooth finish. This sanding process is critical to produce the smooth mirror like finish in the topcoat.

Sealer Primer
- The Sealer Primer is applied prior to the Basecoat in all areas that have not been previously primed with the Surfacer Primer. The Sealer Primer is a two-component high solids urethane that goes on smooth and provides excellent gloss hold out when topcoated.

Base
coat Paint
- Two coats of a high performance, two component high solids polyurethane basecoat will be applied. The Basecoat will be applied to a thickness that will achieve the proper color match. The Basecoat will be used in conjunction with a urethane clear coat to provide protection from the environment.

Clear Coat
- Two (
2 ) coats of Clear Coat will be applied over the Basecoat color. The Clear Coat is a two-component high solids urethane that provides superior gloss and durability to the exterior surfaces. Lap style and roll-up doors will be Clear Coated to match the body. Paint warranty for the roll-up doors will be provided by the roll-up door manufacturer.

After the cab and body are painted, the color will be verified to make sure that it matches the color standard. Electronic color measuring equipment will be used to compare the color sample to the color standard entered into the computer. Color specifications will be used to determine the color match. A Delta E reading will be used to determine a good color match within each family color.

All removable items such as brackets, compartment doors, door hinges, and trim will be removed and painted separately if required, to ensure paint behind all mounted items. Body assemblies that cannot be finish painted after assembly will be finish painted before assembly.

The paint finish quality levels for critical areas of the apparatus (cab front and sides, body sides and doors, and boom lettering panels) are to meet or exceed Cadillac/General Motors GMW
15777
global paint requirements. Orange peel levels are to meet or exceed the #6
A.C.T.
standard in critical areas. The manufacture's written paint standards will be available upon request.

Environmental Impact
Contractor will meet or exceed all current state regulations concerning paint operations. Pollution control will include measures to protect the atmosphere, water and soil. Controls will include the following conditions:

Topcoats and primers will be chrome and lead free.

Metal treatment chemicals will be chrome free. The wastewater generated in the metal treatment process will be treated on-site to remove any other heavy metals.

Particulate emission collection from sanding operations will have a

99.99 percent efficiency factor.

Particulate emissions from painting operations will be collected by a dry filter or water wash process. If the dry filter is used, it will have an efficiency rating of 98 percent. Water wash systems
will be

99.97 percent efficient.

Water from water wash booths will be reused. Solids will be removed on a continual basis to keep the water clean.

Paint wastes are disposed of in an environmentally safe manner.

Empty metal paint containers will be recycled to recover the metal.

Solvents used in clean-up operations will be recycled on-site or sent off-site for distillation and returned for reuse.

Additionally, the finished apparatus will not be manufactured with or contain products that have ozone depleting substances. Contractor will, upon demand, present evidence that the manufacturing facility meets the above conditions and that it is in compliance with his state EPA rules and regulations.
0709846
Paint, Two-Tone Color, Velocity/Impel

CAB TWO-TONE PAINT
The cab will be painted two-tone, with the upper section painted #10
white
and the lower section
painted
#90
red
. There will be
a standard two-tone cab paint break provided
.

There will be
no cab shield provided
.
0709845
Paint, Single Color, Body

BODY PAINT
The body will be
painted to match the lower section of the cab
.
85 973
Bid #:
749
AGENDA ITEM NO. 28.
0646901
Paint Chassis Frame Assy, With
Liner, E-Coat, Standard

PAINT CHASSIS FRAME ASSEMBLY
The chassis frame assembly will be finished with
a single system black top coat
before the
installation of the cab and body, and before installation of the engine and transmission assembly, air brake lines, electrical wire harnesses, etc.

Components that are included with the chassis frame assembly that will be painted (unless otherwise stated in a secondary option) are:

Frame rails
Frame liners
Cross members
Axles
Suspensions
Steering gear
Battery boxes
Bumper extension weldment
Frame extensions
Body mounting angles
Rear Body support substructure (front and rear)
Pump house substructure
Steel fuel tank
Castings
Individual piece parts used in chassis and body assembly Components treated with epoxy E-coat protection prior to paint:

Two (
2 ) C-channel frame rails
Two (
2 ) frame liners
The E-coat process will meet the technical properties shown. 0693797
No Paint Required, Aluminum Front
Wheels

0806169
Paint, Rear Wheels, Tandem Axle,
TAK-4 T3

REAR WHEELS PAINT
All wheel surfaces, inside and outside, will be provided with paint
#90
red
.
0733739
Paint, Axle Hubs

AXLE HUB PAINT
All axle hubs will be painted
to match lower job color
.
0620095
Paint, Drip Rail, Cab

PAINTED RAIN DRIP
The cab roof rain drip will be painted to match the cab roof paint color. 0581434
Transit Coating, Carwell, Corrosion
Protection, Including Underside

TRANSIT COATING
All non-painted metal surfaces on the exterior of the vehicle will be sprayed with a corrosion protective coating provided by Carwell. The coating can be removed with soap and water.

The coating is made of a linseed oil base and is biodegradable.

The underside non-painted metal surfaces will also be coated with a corrosion protective coating. 0007230
Compartment, Painted, Spatter Gray

COMPARTMENT INTERIOR PAINT
The interior of all compartments will be painted with a gray spatter finish for ease of cleaning and to make it easier to touch up scratches and nicks.
86 973
Bid #:
750
AGENDA ITEM NO. 28.
0782203
Aerial Ladder Paint, ASL-Tandem,
LSL, E-Coat

AERIAL DEVICE PAINT COLOR
The aerial device paint procedure will consist of a six ( 6 ) step finishing process as follows:
1 .

Manual Surface Preparation
- All exposed metal surfaces on the aerial device structural components above the rotation point will be thoroughly cleaned and mechanically shot-blasted to remove metal impurities and prepare the aerial for painting. 2 .

Primer/Surfacer Coats
- A two (
2 ) component urethane primer/surfacer will be applied to the mechanically shot-blasted metal surfaces to provide a strong corrosion protective base coat and to smooth out the surface. All seams will be caulked with a two ( 2 ) component epoxy caulk before
painting.
3 .

Hand Sanding
- The primer/surfacer coat of the outer surfaces of the hand rails and base rails will be lightly sanded to a smooth finish.
4 .

Sealer Primer Coat
- A two (
2 ) component sealer primer coat will be applied over the sanded primer.
5 .

Topcoat Paint
- Urethane base coat will be applied to opacity for correct color matching. 6 .

Clearcoat
- Two (
2 ) coats of an automotive grade two (
2 ) component urethane will be applied.

Surfaces that will not be painted include all chrome plated, polished stainless steel, anodized aluminum and bright aluminum treadplate.

All buy out components, such as monitor, nozzle, gauges, etc. will be supplied as received from the vendor.

Removable items such as brackets will be removed and painted separately to ensure paint coverage behind all mounted items.

The stabilizer beams and torque box will be treated with E-coat prior to painting to help provide resistance to corrosion and chemicals. The stabilizers and torque box will be painted black.

The aerial device components will be painted as follows using the aforementioned six ( 6 ) step
finishing process:

Aerial device ladder sections and extension cylinders:
white
10 Aerial egress:
#50
red
(will be contrasting color to the aerial device ladder) Aerial turntable:
white
10 Aerial control console:
white
10 Aerial lift cylinders:
white
10 Aerial boom support:
gloss black primer
0544087
Reflective Band, 6"

REFLECTIVE BAND
A

6.00 "
white
reflective band will be provided across the front of the vehicle and along the sides of the body.
0510041
Reflective across Cab Face, Imp/Vel

The reflective band provided on the cab face will be below the headlights on the fiberglass. 0583454
Stripe, Chevron, Rear, Diamond
Grade, Aerial

REAR CHEVRON STRIPING
There will be alternating chevron striping located on the rear-facing vertical surface of the apparatus. Covered surfaces will include the rear wall and aluminum doors. Rear compartment doors, stainless steel access doors, and the rear bumper will not be covered.

The colors will be red and
fluorescent yellow
diamond grade.

Each stripe will be

6.00 " in width.

This will meet the requirements of the current edition of NFPA 1901
, which states that
50%
of the
rear surface will be covered with chevron striping.
0596383
Stripe, Reflective/Diamond Grade, 6"
on Stabilizers

REFLECTIVE STRIPE ON STABILIZERS
There will be a

6.00 " wide
fluorescent yellow diamond grade
reflective stripe provided on the
forward and rear facing side of all aerial stabilizers. 0011949
"S" Ribbon, Shaded in Reflective
Stripe, Pair
STRIPE, REFLECTIVE, "S" RIBBON
"S" type ribbon(s) will be added to the reflective stripe per preconstruction and match
33607
for
configuration
. Areas adjacent to the "S" portion of the stripe will be shaded and highlighted with an air brush to give it a ribbon affect. There will be
one (
1 )
pair on the vehicle.
0065687
Stripe, Reflective, Cab Doors Interior

CAB DOOR REFLECTIVE STRIPE
A

6.00 " x

16.00 "
black
reflective stripe will be provided across the interior of each cab door. The stripe will be located approximately

1.00 " up from the bottom, on the door panel.

This stripe will meet the current edition of applicable NFPA standards. 0679788
Stripe, Vinyl, Cab Sides, IPO Chrome
Molding

CAB STRIPE
There will be a vinyl stripe provided on both sides of the cab in place of the chrome molding. 0679895
Stripe, Reflective, Box, Boom Sign
with Scrolls, Aerial

BOOM SIGN STRIPING
There will be reflective stripes along all edges of the aerial boom sign. The stripes will have an outline and a scroll at each corner.
0027372
Lettering Specifications, (GOLD
STAR Process)

LETTERING
The lettering will be totally encapsulated between two ( 2 ) layers of clear vinyl.
87 973
Bid #:
751
AGENDA ITEM NO. 28.
0686434
Lettering, Gold Leaf, 3.00", (21-40)

LETTERING
Twenty-one (
21 ) to forty (
40 ) genuine gold leaf lettering,

3.00 " high, with
outline and shade
will be
provided.
0686005
Lettering, Reflective, 7.00", (21-40)

LETTERING
Twenty-one (
21 ) to forty (
40 ) reflective lettering,

7.00 " high, with
outline and shade
will be
provided.
0686013
Lettering, Reflective, 6.00", Each

LETTERING
There will be reflective lettering,

6.00 " high, with
outline and shade
provided. There will be
three
(
3 ) letters
provided.
0686033
Lettering, Reflective, 4.00", Each

LETTERING
There will be reflective lettering,

4.00 " high, with
outline and shade
provided. There will be
three
(
3 ) letters
provided.
0686084
Lettering, Reflective, 3.00", Each

LETTERING
There will be reflective lettering,

3.00 " high, with
outline and shade
provided. There will be
six (
6 )
letters
provided.
0686236
Lettering, Gold Leaf, 5.00", Each

LETTERING
There will be genuine gold leaf lettering,

5.00 " high, with
outline and shade
provided. There will
be
12 letters
provided.
0686256
Lettering, Gold Leaf, 4.00", Each

LETTERING
There will be genuine gold leaf lettering,

4.00 " high, with
outline and shade
provided. There will
be
12 letters
provided.
0052933
SP
Plate, Brushed Stainless Steel for
Lettering

PAINTED PLATE(S) FOR LETTERING
There will be
one (
1 )
brushed stainless steel plate(s) provided for department lettering. They will be mounted
Rear of on turntable handrails per LP. Match Job
33607
.
and will be
Per LP print (
9 " x
18 "). Match Job
33607
in size.
0088685
SP
Sign Kit, Non-Painted S/S
Holder/Number Plate

NUMBER PLATE SIGN KIT FOR LETTERING/NUMERALS
two (
2 )
non-painted stainless steel plate(s) and holder(s) will be provided for department lettering.

They will be mounted
Center of Front Bumper & Rear of Aerial mounted on a special plate & bracket from engineering. Match Job
33607
and
(
1 )
6 "H X
11 "W Polished S/S Placard located on
the center of the front bumper. Match Job
33607
. (
1 )
9 "H X
18 "W Brushed S/S Placard located on
the rear of the Aerial ladder mounted to a special plate and bracket designed by engineering.

Match Job
33607
.
in size.
0594393
SP
Emblem, "Waiving American Flag
With Pole, Pair (mirror images)

"AMERICAN FLAG" EMBLEMS
There will be
one (
1 )
pair of color imaged emblems,

10.00 " wide, featuring a "Waiving American
Flag" with pole and
9-11-01
, installed
Located behind the crew cab window. Match Job
33607
.
.

The pair will be mirror images of each other.
0755303
Artwork File, Provided on Custom
USB Drive

ARTWORK ON CUSTOM USB DRIVE
There will be a custom USB drive with department specific artwork files provided to the Fire Department.

Stock artwork, or artwork developed exclusively by Pierce Manufacturing, and proprietary fonts will not be included on the USB drive.
0654570
Emblem, Vinyl, Per Dept. Submittal,
Each
EMBLEM
There will be
two (
2 )
vinyl emblem(s), approximately

10.00 "-

12.00 "
in size, installed
Behind the
cab door near the roofline and match job
38442
for location and orientation.
. the emblem will be
modeled after the department submitted information (art, patch, etc). 0769753
Emblem, American Flag Painted on
Cab Grille, All Custom Chassis

CAB GRILLE DESIGN
An American flag design will be painted on the cab grille. 88 973
Bid #:
752
AGENDA ITEM NO. 28.
0772003
Manual, Fire Apparatus Parts, USB
Flash Drive, Custom

FIRE APPARATUS PARTS MANUAL
There will be
one (
1 )
custom parts manual(s) in USB flash drive format for the complete fire apparatus provided.

The manual(s) will contain the following:

Job number
Part numbers with full descriptions
Table of contents
Parts section sorted in functional groups reflecting a major system, component, or assembly Parts section sorted in alphabetical order
Instructions on how to locate parts
Each manual will be specifically written for the chassis and body model being purchased. It will not be a generic manual for a multitude of different chassis and bodies.

Service Parts Internet Site
The service parts information included in these manuals are also available on the Pierce website.

The website offers additional functions and features not contained in this manual, such as digital photographs and line drawings of select items. The website also features electronic search tools to assist in locating parts quickly.
0772037
Manual, Chassis Service, USB Flash
Drive, Custom

CHASSIS SERVICE MANUALS
There will be
one (
1 )
chassis service manuals on USB flash drives containing parts and service information on major components provided with the completed unit.

The manual will contain the following sections:

Job number
Table of contents
Troubleshooting
Front Axle/Suspension
Brakes
Engine
Tires
Wheels
Cab
Electrical, DC
Air Systems
Plumbing
Appendix
The manual will be specifically written for the chassis model being purchased. It will not be a generic manual for a multitude of different chassis and bodies. 0773381
Manual, Chassis Operation, (1) USB
Flash Drive, Custom

CHASSIS OPERATION MANUAL
The chassis operation manual will be provided on one (
1 ) USB flash drive.
0030008
Warranty, Basic, 1 Year, Apparatus,
WA0008
ONE (
1 ) YEAR MATERIAL AND WORKMANSHIP
A Pierce basic apparatus limited warranty certificate, WA 0008
, is included with this proposal.
0611136
Warranty, Chassis, 3 Year,
Velocity/Impel, WA0284

THREE (
3 ) YEAR MATERIAL AND WORKMANSHIP
The Pierce custom chassis limited warranty certificate, WA 0284
, is included with this proposal.
0696698
Warranty, Engine, Cummins, 5 Year,
WA0181

ENGINE WARRANTY
A Cummins
five (
5 ) year
limited engine warranty will be provided. A limited warranty certificate, WA
0181
, is included with this proposal.
0684953
Warranty, Steering Gear, Sheppard
M110, 3 Year WA0201

STEERING GEAR WARRANTY
A Sheppard
three (
3 ) year
limited steering gear warranty will be provided. A copy of the warranty certificate will be submitted with this proposal.
0595767
Warranty, Frame, 50 Year,
Velocity/Impel, WA0038

FIFTY (
50 ) YEAR STRUCTURAL INTEGRITY
The Pierce custom chassis frame and crossmembers limited warranty certificate, WA 0038
, is
included with this proposal.
0595698
Warranty, Axle, 3 Year, TAK-4,
WA0050

FRONT AXLE THREE (
3 ) YEAR MATERIAL AND WORKMANSHIP WARRANTY
The Pierce TAK-
4 suspension limited warranty certificate, WA
0050
, is included with this proposal.
0644874
Warranty, Axle, 3 Year, TAK-4, IRS,
WA0249

REAR AXLE THREE (
3 ) YEAR MATERIAL AND WORKMANSHIP WARRANTY
Pierce TAK-
4 ® independent rear suspension will be provided with a three ( 3 ) year material and
workmanship limited warranty. The manufacturer's warranty will provide that the independent rear suspension be free from any defect related to material and workmanship on the portion of the apparatus built by the manufacturer that would arise under normal use and service. 0652758
Warranty, ABS Brake System, 3 Year,
Meritor Wabco, WA0232

ABS BRAKE SYSTEM THREE (
3 ) YEAR MATERIAL AND WORKMANSHIP WARRANTY
A Meritor Wabco
™
ABS brake system limited warranty certificate, WA
0232
, is included with this
proposal.
89 973
Bid #:
753
AGENDA ITEM NO. 28.
0019914
Warranty, Structure, 10 Year, Custom
Cab, WA0012
TEN (
10 ) YEAR STRUCTURAL INTEGRITY
The Pierce custom cab limited warranty certificate, WA
0012
, is included with this proposal.
0744240
Warranty, Paint, 10 Year, Cab, Pro-
Rate, WA0055
TEN (
10 ) YEAR PRO-RATED PAINT AND CORROSION
A Pierce cab limited pro-rated paint warranty certificate, WA 0055
, is included with this proposal.
0595770
Warranty, Power Step, 2 Year,
WA0031
TWO (
2 ) YEAR MATERIAL AND WORKMANSHIP
The Pierce power step limited warranty certificate, WA
0031
, is included with this proposal.
0524627
Warranty, Electronics, 5 Year, MUX,
WA0014
FIVE (
5 ) YEAR MATERIAL AND WORKMANSHIP
The Pierce Command Zone electronics limited warranty certificate, WA 0014
, is included with this
proposal.
0695416
Warranty, Pierce Camera System,
WA0188

CAMERA SYSTEM WARRANTY
A Pierce fifty four (
54 ) month
warranty will be provided for the camera system
.
0708760
Warranty, Not Applicable, LED Strip
Lights

COMPARTMENT LIGHT WARRANTY
The compartment lights will not offer an extended warranty. 0046369
Warranty, 5-year EVS Transmission,
Standard Custom, WA0187

TRANSMISSION WARRANTY
The transmission will have a
five (
5 ) year/unlimited mileage
warranty covering
100
percent
parts and labor. The warranty will be provided by Allison Transmission.

Note: The transmission cooler is not covered under any extended warranty you may be getting on your Allison Transmission. Please review your Allison Transmission warranty for coverage limitations.
0685945
Warranty, Transmission Cooler,
WA0216

TRANSMISSION COOLER WARRANTY
The transmission cooler will carry a five (
5 ) year parts and labor warranty (exclusive to the
transmission cooler). In addition, a collateral damage warranty will also be in effect for the first three (
3 ) years of the warranty coverage and will not exceed
$10,000
per occurrence. A copy of
the warranty certificate will be included with this proposal. 0688798
Warranty, Water Tank, Lifetime, UPF,
Poly Tank, WA0195

WATER TANK WARRANTY
A UPF poly water tank limited warranty certificate, WA
0195
, is included with this proposal.
0596025
Warranty, Structure, 10 Year, Body,
WA0009
TEN (
10 ) YEAR STRUCTURAL INTEGRITY
The Pierce apparatus body limited warranty certificate, WA 0009
, is included with this proposal.
0693126
Warranty, AMDOR, Roll-up Door, 10
Year/5 Year Painted, WA0185

ROLL UP DOOR MATERIAL AND WORKMANSHIP WARRANTY
An AMDOR roll-up door limited warranty will be provided. The roll-up door will be warranted against manufacturing defects for a period of
ten (
10 ) years
. A
five (
5 ) year
limited warranty will
be provided on painted roll up doors.

The limited warranty certificate, WA
0185
, is included with this proposal.
0889364
Warranty, Pump, Pierce, PUC-NG, 7
Year Parts, 1 Year Labor, WA0390

SEVEN (
7 ) YEAR PARTS, ONE (
1 ) YEAR LABOR
The pump and its components will be provided with a seven ( 7 ) year parts and one (
1 ) year labor
limited warranty. The manufacturer's warranty will provide that the pump and its components will be free from failures caused by defects in material and workmanship that would arise under normal use and service.

A copy of the warranty certificate will be submitted with the bid package. 0648675
Warranty, 10 Year S/S Pumbing,
WA0035
TEN (
10 ) YEAR PUMP PLUMBING WARRANTY
The Pierce apparatus plumbing limited warranty certificate, WA 0035
, is included with this
proposal.
0641372
Warranty, Foam System, Not
Available
0006999
Warranty, Structure, 20 Year, Aerial
Device, WA0052

TWENTY (
20 ) YEAR AERIAL DEVICE STRUCTURAL INTEGRITY WARRANTY
The Pierce device limited warranty certificate, WA
0052
, is included with this proposal.
90 973
Bid #:
754
AGENDA ITEM NO. 28.
0687388
Warranty, Swivels, 5 Year, Aerial
Device, WA0197

AERIAL SWIVEL WARRANTY
An Amity five (
5 ) year limited swivel warranty will be provided. A copy of the warranty certificate will be included with this proposal.
0685727
Warranty, Hydraulic System and
Components, 3 Year/5 Year, WA0200

HYDRAULIC SYSTEM COMPONENTS WARRANTY
Aerial hydraulic system components will be provided with a five ( 5 ) year material and
workmanship limited warranty.

HYDRAULIC SEAL WARRANTY
Aerial hydraulic seals will be provided with a three (
3 ) year material and workmanship limited
warranty.

A copy of the warranty certificates is included with this proposal. 0687327
Warranty, Waterway, 10 Year, Aerial
Device, WA0198

AERIAL WATERWAY WARRANTY
An Amity ten (
10 ) year limited waterway warranty will be provided. A copy of the warranty certificate is included with this proposal.
0595860
Warranty, Paint, 4 Year, Aerial
Device, Pro-Rated, WA0047

FOUR (
4 ) YEAR PRO-RATED PAINT AND CORROSION
A Pierce aerial device limited pro-rated paint warranty certificate, WA 0047
, is included with this
proposal.
0595820
Warranty, Paint, 10 Year, Body, Pro-
Rate, WA0057
TEN (
10 ) YEAR PRO-RATED PAINT AND CORROSION
A Pierce body limited pro-rated paint warranty certificate, WA 0057
, is included with this proposal.
0595421
Warranty, Goldstar, 3 Year,
Apparatus, WA0018

THREE (
3 ) YEAR MATERIAL AND WORKMANSHIP
The Pierce Goldstar gold leaf lamination limited warranty limited warranty certificate, WA 0018
, is
included with this proposal.
0819254
Certification, Vehicle Stability,
CD0196

VEHICLE STABILITY CERTIFICATION
The fire apparatus manufacturer will provide a certification stating the apparatus complies with NFPA
1900
, current edition, section

7.14 , Vehicle Stability. The certification is included with this proposal.
0808577
Certification, Engine Installation,
Velocity, Cummins X15, 2027

ENGINE INSTALLATION CERTIFICATION
The fire apparatus manufacturer will provide a certification, along with a letter from the engine manufacturer stating they approve of the engine installation in the bidder's chassis. The certification will be provided at the time of delivery. 0686786
Certification, Power Steering,
CD0098

POWER STEERING CERTIFICATION
The fire apparatus manufacturer will provide a certification stating the power steering system as installed meets the requirements of the component supplier. The certification is included with this proposal.
0892701
Certification, Cab Integrity,
Impel/Velocity FR, CD0190

CAB INTEGRITY CERTIFICATION
The fire apparatus manufacturer will provide a cab crash test certification with this proposal. The certification will state that a specimen representing the substantial structural configuration of the cab has been tested and certified by an independent third party test facility. Testing events will be documented with photographs, real-time and high-speed video, vehicle accelerometers, cart accelerometers, and a laser speed trap. The fire apparatus manufacturer will provide a state licensed professional engineer to witness and certify all testing events. Testing will meet or exceed the requirements below:

SAE J
2422
Cab Roof Strength Evaluation - Quasi-Static Loading Heavy Trucks.

European Occupant Protection Standard ECE Regulation No. 29 .

SAE J
2420
COE Frontal Strength Evaluation - Dynamic Loading Heavy Trucks.

Side Impact
The cab will be subjected to dynamic preload where a
14,320
-lb moving barrier is slammed into
the side of the cab at

5.50 mph, striking with an impact of
13,000
ft-lb of force. This test is part of
the SAE J
2422
test procedure and more closely represents the forces a cab will see in a rollover incident.

Roof Crush
The same cab will be subjected to a roof crush force of 22,050
lb. This value meets the ECE
29 criteria and is equivalent to the front axle rating up to a maximum of ten ( 10 ) metric tons.

Additional Roof Crush
The same cab will be subjected to a roof crush force of 100,000
lb. (Four and a half times the
load criteria of ECE
29 )
Frontal Impact
The same cab will withstand a frontal impact of
32,600
ft-lb of force using a moving barrier in
accordance with SAE J
2420
.

Additional Frontal Impact
The same cab will withstand a frontal impact of
65,200
ft-lb of force using a moving barrier. (Twice
the force required by SAE J
2420
)
The same cab will withstand all tests without any measurable intrusion into the survival space of the occupant area.
91 973
Bid #:
755
AGENDA ITEM NO. 28.
0548950
Certification, Cab Door Durability,
Velocity/Impel, CD0001

CAB DOOR DURABILITY CERTIFICATION
Robust cab doors help protect occupants. Cab doors will survive a 200,000
-cycle door slam test
where the slamming force exceeds
20 G's of deceleration. The bidder will certify that the sample doors similar to those provided on the apparatus have been tested and have met these criteria without structural damage, latch malfunction, or significant component wear. 0548967
Certification, Windshield Wiper
Durability, Impel/Velocity, CD0005

WINDSHIELD WIPER DURABILITY CERTIFICATION
Visibility during inclement weather is essential to safe apparatus performance. Windshield wipers will survive a
3 million cycle durability test in accordance with section

6.2 of SAE J
198

Windshield
Wiper Systems - Trucks, Buses and Multipurpose Vehicles.

The bidder will certify that the wiper
system design has been tested and that the wiper system has met these criteria. 0667411
Certification, Electric Window
Durability, Velocity/Impel FR, CD0004

ELECTRIC WINDOW DURABILITY CERTIFICATION
Cab window roll-up systems can cause maintenance problems if not designed for long service life. The window regulator design will complete
30,000
complete up-down cycles and still function
normally when finished. The bidder will certify that sample doors and windows similar to those provided on the apparatus have been tested and have met these criteria without malfunction or significant component wear.
0549273
Certification, Seat Belt Anchors and
Mounting, Imp/Vel/Vel SLT, CD0018

SEAT BELT ANCHOR STRENGTH
Seat belt attachment strength is regulated by Federal Motor Vehicle Safety Standards and should be validated through testing. Each seat belt anchor design will withstand 3000
lb of pull on both
the lap and shoulder belt in accordance with FMVSS
571.210
Seat Belt Assembly Anchorages.

The bidder will certify that each anchor design was pull tested to the required force and met the appropriate criteria.

SEAT MOUNTING STRENGTH
Seat attachment strength is regulated by Federal Motor Vehicle Safety Standards and should be validated through testing. Each seat mounting design will be tested to withstand 20 G's of force in
accordance with FMVSS
571.207
Seating Systems. The bidder will certify that each seat mount and cab structure design was pull tested to the required force and met the appropriate criteria. 0735950
Certification, Cab HVAC System Perf,
Vel/Imp FR,
CD0166/CD0168/CD0176/CD0177

PERFORMANCE CERTIFICATIONS
Cab Air Conditioning
Good cab air conditioning temperature and air flow performance keeps occupants comfortable, reduces humidity, and provides a climate for recuperation while at the scene. The cab air conditioning system will cool the cab from a heat-soaked condition at 100
degrees Fahrenheit to
an average of
78 degrees Fahrenheit in
30 minutes. The bidder will certify that a substantially similar cab has been tested and has met these criteria.

Cab Defroster
Visibility during inclement weather is essential to safe apparatus performance. The defroster system will clear the required windshield zones in accordance with SAE J 381
Windshield
Defrosting Systems Test Procedure And Performance Requirements - Trucks, Buses, And Multipurpose Vehicles.

The bidder will certify that the defrost system design has been tested in a cold chamber and passes the SAE J
381
criteria.

Cab Auxiliary Heater
Good cab heat performance and regulation provides a more effective working environment for personnel, whether in-transit, or at a scene. An auxiliary cab heater will warm the cab 77 degrees
Fahrenheit from a cold-soak, within
30 minutes when tested using the coolant supply methods found in SAE J
381
. The bidder will certify, at time of delivery, that a substantially similar cab has been tested and has met these criteria.
0545073
Amp Draw Report, NFPA Current
Edition

AMP DRAW REPORT
The bidder will provide, at the time of bid and delivery, an itemized print out of the expected amp draw of the entire vehicle's electrical system.

The manufacturer of the apparatus will provide the following:

Documentation of the electrical system performance tests.

A written load analysis, which will include the following:

The nameplate rating of the alternator.

The alternator rating under the conditions specified per:

Current edition of applicable NFPA standards.

The minimum continuous load of each component that is specified per:

Current edition of applicable NFPA standards.

Additional loads that, when added to the minimum continuous load, determine the total connected load.

Each individual intermittent load.

All of the above listed items will be provided by the bidder per the current edition of applicable NFPA standards.
0002758
Amp Draw, NFPA/ULC Radio
Allowance
0799248
Appleton/Florida BTO

0000049
Ascendant BODY

92 973
Bid #:
756
AGENDA ITEM NO. 28.
0000012

PIERCE CHASSIS
0004713

ENGINE, OTHER
0046396
EVS 4000 Series TRANSMISSION
0520324

PIERCE PUMP, PUC

0020009

POLY TANK

0028048

FOAM SYSTEM
0020006

SIDE CONTROL
0020007

AKRON VALVES

0020015

ABS SYSTEM

0755453

AERIAL BASE

93 973
Bid #:
757
AGENDA ITEM NO. 28.

Option
Description
Type*
Minimum
Load
Intermittent
Load
Total
Connected
0001244
High Idle w/Electronic Engine, Custom

0.00 1.20

0.00 0002617
PTO switch, w/light - aerial

0.00 0.00

0.08 0005780
Control, Air Horn At Pmp Pnl, Button

0.00 0.16

0.00 0012188
Mirrors, Velvac, 2025, Heated/Remote, w/Heated Convex

0.00 0.00

8.00 0015215
Reel, Booster, Over Pump, Right Side, Steel

0.00 36.00

0.00 0062992
Gauge, Foam Level, (1) Tank, Class 1, GAAAR 5lt

0.00 0.00

1.00 0072153
Primer, Trident, Air Prime, Air Operated

0.00 0.00

0.00 0098833
Batteries, (5) Deka Grp 31, 1000 CCA each, 1 Iso Bat, Threaded Stud

0.00 3.00

0.00 0122466
Cab Lift, Elec/Hyd, w/Manual Override, Imp/Vel

0.00 180.00

0.00 0543751
Light, Do Not Move Apparatus

0.00 0.80

0.00 0549333
Indicators, Engine, Included with Pressure Controller

0.00 0.35

0.00 0589905
Alarm, Back-up Warning, PRECO 1040

0.00 0.50

0.00 0617886
Foam Sys, FoamPro 1600, Single Agent, PUC, Multi Select Feature

0.00 36.00

0.00 0618458
Light, Pump Compt, Wln 3SC0CDCR LED White, PUC

0.00 0.36

0.00 0626097
Light, Map, Sunnex HS76*-00 Series, Swivel Joint, Clear Lens, Ceiling Mount

0.00 0.00

1.56 0628472
Light, Map, Overhead, Peterson M371S LED, Rectangular
w/Switch 2lts

0.00 0.24

0.00 0653677
Lighting, Rung, LED, TecNiq, 4 Section, Base, Lower/Upper Mid, Fly

0.00 0.00

7.20 0656362
Alarm, Directionals In Cab, MUX

0.00 0.00

0.00 0667902
Controls, Electric Windows, All Cab Doors, Impel/Velocity FR

0.00 26.00

0.00 0687994
Engine Brake, Jacobs Compression Brake, Cummins Engine

0.00 0.42

0.00 0693439
Lights, Engine Compt, Custom, Auto Sw, w/Fld Chk Dr Wln 3SC0CDCR, 3" LED Trim

0.00 0.76

0.00 0745863
Lights, Side, Wln M9** LED, Trm Fet 2nd

0.00 1.80

1.20 0745867
Lights, Side, Wln M9** LED, Trm Fet 1st

0.00 1.80

1.20 0748793
Lights, Wln, S44M** 44" 12VDC, RS Body

0.00 0.00

10.80 0748795
Lights, Wln, S44M** 44" 12VDC, LS Body

0.00 0.00

10.80 0763096
Fittings, Compression IPO PTC, All Pump Panel Gauges

0.00 0.16

0.00 0772848
Lights, Wln, S16*M* 16" 12VDC, 2nd

0.00 0.00

3.60 0772850
Lights, Wln, S16*M* 16" 12VDC, 1st

0.00 0.00

3.60 0792976
Stabilizers, Ascendant Tandem, Rear Mount Steel, 16' Spread, 18" Pen, MUX

0.00 4.00

0.00 0803462
Lights, Tip, Wln MP** LED, 2lts

0.00 0.00

7.03 0804781
Aerial Scene Lts Separated into Aerial Tip Category and Aerial Tracking Category

0.00 0.00

0.00 0806466
Lights, Backup, Wln M62BU, LED, For Tail Lt Housing

0.00 3.20

0.00 0809551
Light, GTT, 794* Opticom Emitter, Remote Mtd on Cab Roof, Hardwired

0.00 0.03

0.00 0817058
Camera, Pierce, LS Mux, R Camera, SD, CL714

0.00 1.20

0.00 0819994
Radio, Jensen, AM/FM/WB, Bluetooth

0.00 0.00

2.00 0821263
Wiring, Spare, 20 A 12V DC, 12 Ckt FB, Blue Sea 5026 Batt Dir 1st NFPA1900/ULC

0.00 0.00

20.00 0821302
Wiring, Spare,12V DC, USB-A & C, Kussmaul 091-264 Cab Batt Dir 1st NFPA1900/ULC

0.00 0.00

6.00 0821329
Wiring, Spare, 10 A 12V DC Batt Dir 1st NFPA1900/ULC

0.00 0.00

10.00 0821337
ABS Wabco Brake System, Tandem Rear Axle, Tak-4, NFPA
1900/ULC

0.00 6.00

0.00 0821619
Switch, AM/FM Radio, Location, Non-Bat Direct NFPA/ULC 2024

0.00 0.00

20.00 0826636
Wiring, Spare, (1) 15A 12V DC, Multi Loc, Cab, B+, 1st, NFPA1900/ULC

0.00 0.00

15.00 0830360
Wiring, Spare, (1) 15A 12V DC, Multi Loc, Cab, B+, 2nd, NFPA1900/ULC

0.00 0.00

15.00 0833701
Switch, Latching, Additional for Opticom

0.00 0.00

0.08 0833707
Intercom, Setcom 950MAX, 6-Pos, 2-Radio, D,O,3C Wired, 1 Wireless

0.00 0.00

0.25 0889662
Lights, Wln, S16*M* 16.37" 12VDC, Brkt Fet 2nd

0.00 0.00

3.66 0889664
Lights, Wln, S16*M* 16.37" 12VDC, Brkt Fet 1st

0.00 0.00

3.66 0889727
Light, P25 LED, Compartment

0.00 0.00

0.05 * UDMC = User Defined Mission Critical, LM = User Defined Load Managed, S = Electrical Amperage Supply 1 Electrical Analysis
6/16/2025
Bid #:
973
CLV Velocity PUC 107 Ascendant
Sales Rep:

Organization:

Young, Dewayne
Golden State Fire Apparatus, Inc
Desc:

Job #:

Customer:

CLOVIS FIRE DEPARTMENT
Option:

Pierce Command Zone, Advanced Electronics & Control
System, Vel WiFi CZT
Type:

Multiplexed
758
AGENDA ITEM NO. 28.

Option
Description
Type*
Minimum
Load
Intermittent
Load
Total
Connected
0898549
Cab Air Filtration, TFT CrewProtect 100, 12v DC, Loc, CARE

0.00 0.00

1.50 0741239
HVAC, Heavy-Duty, Impel/Velocity FR, CARE
Load Managed

0.00 0.00
136.00
0831848
Inverter/Battery Charger, Vanner, ITC12-3200 3200W, Non-NFPA 2024, 80 Amp
LM - Last

0.00 0.00
312.50
0000458
Platform, Slide Out, 500 lb Capacity, Alum 4-Way
NFPA

1.50 0.00

0.00 0002615
Switch, Aerial 12V Master
NFPA

0.08 0.00

0.00 0002758
Amp Draw, NFPA/ULC Radio Allowance
NFPA

5.00 0.00

0.00 0010758
Flow Meter, Waterway, PAL, 110' Ascendant, MUX
NFPA

0.50 0.00

0.00 0023670
Compt, IPO Stairs RS, Lap Door
NFPA

0.90 0.00

0.90 0063685
Compt, LS F/H F/D, Dbl Drs, w/o Chute, Ascendant Tandem, 105 HDL, 100 HAL
NFPA

2.70 0.00

2.70 0068703
Lights, Grote Supernova LED, Stabilizer Beam, (1) Set
NFPA

1.60 0.00

0.00 0092582
Load Manager/Sequencer, MUX
NFPA

0.56 0.56

0.00 0120828
Compt, LS Turntable, F/H F/D, Lap Drs, Ascendant TA, 105', 8" Rsd,100 HAL
NFPA

1.80 0.00

1.80 0120840
Compt, RS Turntable, F/H, Lap Drs, Ascendant Tandem, 105', 8" Rsd, 100 HAL
NFPA

2.70 0.00

2.70 0516983
Gauges, Engine, Included With Pressure Controller, PUC
NFPA

0.30 0.00

0.00 0534987
Lights, Clearance/Marker/ID, Rear, Truck-Lite 33050R LED 7Lts, Aerial
NFPA

0.35 0.00

0.00 0540746
Lights, Stabilizer Warn (2) Sets, Wln M6* LED, Colored Lens NFPA

3.60 5.40

0.00 0541116
Lights, Rear/Side Up Zone, Wln M6* LED, Colored Lens 4lts NFPA

4.00 0.00

0.00 0542387
Compt, IPO Chute, Rear Access, Tandem Axle, Smooth Alum Door
NFPA

0.90 0.00

0.90 0555915
Wiper Control, 2-Speed with Intermittent, MUX, Impel/Velocity NFPA

2.10 8.40

0.00 0557322
Lights, Step, P25 at Rear Tailboard, PUC, 4lts Perm Lts NFPA

0.50 0.00

0.00 0564654
Lights, Rear Zn Lwr, Wln M6*, Colored Lens, For Tail Light Housing
NFPA

1.80 2.70

0.00 0568369
Cab Instruments, Ivory Gauges, Chrome Bezels, Impel/Velocity 2010
NFPA

1.26 0.00

0.00 0587034
Air Dryer, Bendix, AD-IP w/Heat, 2010
NFPA

4.70 0.00

0.00 0592278
Light, Front Zone, Wln M6*C & M6*C Sdy Burn LED, Clear Lens, 4lts Q Bezel
NFPA

2.70 5.40

0.90 0601949
Light, Turntable Console, TecNiq T-10, LED Strip Light
NFPA

0.20 0.00

0.00 0601972
Lights, Turntable Walkway, P25, LED
NFPA

0.35 0.00

0.00 0604635
Lightbar, Wln, Freedom IV-Q, 2-21.5", RRRWR RWRRR
NFPA

6.48 2.48

7.28 0612938
Compt, Storage, (2) Rear Facing, Overhead, 9 W x 10 H x 20 D, Imp/Vel FR Notch
NFPA

0.10 0.10

0.00 0618791
DEF Tank, 4.5 Gallon, LS Fill, Forward of Axle, Common Air Bottle Door
NFPA

0.60 11.40

0.00 0620054
Light, Directional/Marker, Intermediate, Weldon 9186-8580-29 LED 2lts
NFPA

0.10 0.90

0.00 0647647
Lights, Dome, FRP Dual LED 4 Lts
NFPA

0.80 0.80

0.00 0648425
Light, Directional, Wln 600 Cmb, Cab Crn, Wrp Bzl Out HD Lts, Imp/Vel/AXT/Qtm
NFPA

0.70 0.70

0.00 0653937
Flasher, Headlight Alternating
NFPA

0.08 0.00

0.00 0667186
Light, Slide-Out Pump Operator Step, OSS Access LED, Short Step
NFPA

0.65 0.00

0.00 0668313
Cab, Velocity FR, 7010 Raised Roof w/Notch, PUC
NFPA

6.80 10.20

0.00 0688049
Siren, Federal EQ2B-200, 200 Watt
NFPA

2.01 18.13

0.00 0708752
Lights, Torque Box Ladder Storage, Amdor AY-9220-020, 2 Lts, LED
NFPA

1.00 0.00

0.00 0709438
Lights, Walk Surf, FRP Flood, LED
NFPA

2.00 0.00

0.00 0724463
Controller, Pressure, Pierce LCD , PUC
NFPA

1.70 0.00

0.00 0731813
Hour Meter, Aerial, Included in Information Centers, ASL, AAT, ASP
NFPA

0.10 0.00

0.00 0736393
Intercom, 3-Way Fire Research ICA910 Hands Free
NFPA

0.50 0.00

0.00 0738037
Light, Pump Op & Panel, Side Ctrl, PUC, AY-LB-12SHW-020 Und Crosslay, OH Chr Cvr
NFPA

3.00 0.00

0.00 0739224
Indicator Light @ Pump Panel, Throttle Ready, Incl w/Pressure Gov/Throttle,Green
NFPA

0.10 0.00

0.00 0749399
Light, Visor Mt, Wln S72M**, 72" Cnt Feature
NFPA

0.32 0.00

18.68 0750438
Water Level Gauge, Wln PSTANK2, LED 1-Light, 4-Level
NFPA

1.60 0.00

0.00 0755095
Aerial, 107' ASL Tandem, 750/500 Tip, 50 MPH
NFPA

5.00 0.00

0.00 0756688
Gauge, Water Level, Pierce, In pressure Controller, w/Mini Slave, PUC, Lt Driver
NFPA

1.23 0.00

0.00 0762388
Lights, Stabilizer Scene, (2) sets, Amdor AY-LB-12HW012, LED NFPA

0.72 0.00

0.00 * UDMC = User Defined Mission Critical, LM = User Defined Load Managed, S = Electrical Amperage Supply 2 Electrical Analysis
6/16/2025
Bid #:
973
CLV Velocity PUC 107 Ascendant
Sales Rep:

Organization:

Young, Dewayne
Golden State Fire Apparatus, Inc
Desc:

Job #:

Customer:

CLOVIS FIRE DEPARTMENT
Option:

Pierce Command Zone, Advanced Electronics & Control
System, Vel WiFi CZT
Type:

Multiplexed
759
AGENDA ITEM NO. 28.

Option
Description
Type*
Minimum
Load
Intermittent
Load
Total
Connected
0762413
Light, Boom Support, Amdor AY-LB-12HW012, 12" LED
NFPA

0.18 0.00

0.00 0768459
Lights, Perimeter Cab, Amdor AY-LB-12HW012 LED 4Dr, Pwr Step, Vel/Imp
NFPA

0.72 0.00

0.00 0768498
Lights, Perimeter Body, Amdor AY-LB-12HW020 LED 1lt,
Turntable Access
NFPA

0.17 0.00

0.00 0769559
Lights, Perimeter Pump House, Amdor AY-LB-12HW012 LED 2lts NFPA

0.36 0.00

0.00 0780433
Compt, RS F/H F/D Frt, Dbl Drs, Ascend TA, 105', 100 HAL NFPA

2.70 0.00

2.70 0783153
Headlights, Rect LED, JW Spkr Evo 2, AXT/Enf/Imp/Sab/Vel NFPA

4.20 4.20

0.00 0788934
Lights, Side Zone Lower, Wln M7* LED, Front Split Color , Clr/Color Lens, 3pr
NFPA

5.40 8.10

0.00 0791493
Light, Traffic Directing, Wln TAM65 36" Long LED
NFPA

1.26 2.52

0.00 0802753
Lights, Tracking, Wln MP** LED, 2lts
NFPA

8.00 0.00

0.00 0804514
Lights, Tail, Wln M62BTT* Red Stop/Tail & M62T* Amber Dir Arw For Hsg
NFPA

0.83 2.49

0.00 0805711
Cabinet, Rear Facing, LS, 24 W x 32 H x 30.5 D, Radius, Ext Acc, Imp/Vel
NFPA

0.48 0.48

0.00 0809508
Lights, Cab & Crw Cab Acs Stps, P25, LED, 4Lts, 4-Door Cab, Auto Steps
NFPA

0.14 0.14

0.00 0811976
Engine, Cummins X15, 565 hp, 1850 lb-ft, W/OBD, EPA 2027, Velocity, PUC-NG
NFPA

6.00 0.00

0.00 0812671
Valve, w/Relief, LS Main Inlet, 6", Elec, Akron 9333 Cont, w/O- ride,PUC
NFPA

0.28 17.72

0.00 0812672
Valve, w/Relief, RS Main Inlet, 6", Elec, Akron 9333 Cont, w/O- ride,PUC
NFPA

0.28 17.72

0.00 0814201
Vehicle Information Center, 7" Color Display, Touchscreen, MUX, CL714
NFPA

1.20 0.00

0.00 0814217
Control Stations, ASL Tandem Axle, MUX, Color Display, CL714 NFPA

4.26 0.00

0.00 0831927
Lights, Rear Scene, Wln, MPP**S Micro Pioneer LED, Ped/Swivel, 2Lts
NFPA

7.00 0.00

0.00 0833781
Cabinet, Rear Facing, RS, 21.5 W x 32 H x 30.5 D, Radius, Ext Acc, Imp/Vel
NFPA

0.32 0.32

0.00 0887546
Trans, Allison 6th Gen, 4000 EVS P, w/Prognostics,
Imp/Vel/SFR/Enf
NFPA

2.00 2.00

0.00 0889577
Bracket, License Plate & Light, P25 LED, Stainless Brkt NFPA

0.07 0.00

0.00 0889980
Lights, Step (3), P25 LED, One Side
NFPA

0.15 0.00

0.00 0898617
Lights, Hose Bed, Sides, Dual Strips, 45 Ends
NFPA

3.30 0.00

0.00 0647728
Alternator, 430 amp, Delco Remy 55SI
S

0.00 0.00

0.00 Load Totals:
124.99
426.84
640.33
Minimum Continuous Load
Supply:
253.00
Demand:
124.99
Variance:
128.01
Total Connected Load
Supply:
369.00
Demand:
316.82
Variance:

52.18 Note: Minimum Continous Load is in "Blocking Right of Way" mode.(Reference current edition of NFPA 1901) Note: Intermittent Load items are not factored in on any alternator load comparisons. These items are included on the report for reference only and should be looked at as amp draw exclusion items. (Reference current edition of NFPA 1901) Note: Total Connected Load "Demand" represents Total Connected Load minus any Load Managed items 253.00
369.00
Alternator Output at Idle:

Alternator Output at Governed Speed:
* UDMC = User Defined Mission Critical, LM = User Defined Load Managed, S = Electrical Amperage Supply 3 Electrical Analysis
6/16/2025
Bid #:
973
CLV Velocity PUC 107 Ascendant
Sales Rep:

Organization:

Young, Dewayne
Golden State Fire Apparatus, Inc
Desc:

Job #:

Customer:

CLOVIS FIRE DEPARTMENT
Option:

Pierce Command Zone, Advanced Electronics & Control
System, Vel WiFi CZT
Type:

Multiplexed
760
AGENDA ITEM NO. 28.

Turning Performance Analysis
Bid Number:
973
Chassis:

Velocity Chassis, Aerials, Tandem Axle, Ascendant/LSL PUC- NG (Big Block)
Department:

CLOVIS FIRE DEPARTMENT
Body:

Aerial, HD Ladder 107' ASL Tandem, PUC, Alum Body
Parameters:
*Inside Cramp Angle:
45°
Axle Track:

82.92 in.

Wheel Offset:

4.68 in.

Tread Width:

16.3 in.

Chassis Overhang:
78 in.

Additional Bumper Depth:
13 in.

Front Overhang:
91 in.

Wheelbase:
250.5 in.

Calculated Turning Radii:

Inside Turn:
19 ft. 10 in.

Curb to curb:
35 ft. 10 in.

Wall to wall:
40 ft. 6 in.

Notes:
*Actual Inside cramp angle may be less than shown.

Curb to Curb turning radius calculated for 9.00 inch curb. 06/16/2025
Category
Option
Description
Aerial Devices
0755095
Aerial, 107' ASL Tandem, 750/500 Tip, 50 MPH
Axle, Front, Custom
0637059
Axle, Front, Oshkosh TAK-4, Non Drive, 24,000 lb, Velocity (425 Tires) Tires, Front
0899289
Tires, Front, Goodyear, Armor MAX MSA, 425/65R22.50, 20 ply, Fire Service Load
Bumpers
0123623
Bumper, 13" Extended, Imp/Vel
Wheels, Front
0019611
Wheels, Front, Alcoa, 22.50" x 12.25", Aluminum, Hub Pilot 761
AGENDA ITEM NO. 28.

Definitions:

Inside CrampAngle
Maximum turning angle of the front inside fire.

Axle Track
King-pin to King-pin distance of front axle.

Wheel Offset
Offset from the center line of the wheel to the King-pin.

Tread Width
Width of the tire tread.

Chassis Overhang
Distance of the center line of the front axle to the front edge of the cab. This does not include the bumper depth.

Additional Bumper Wheel
Depth that the bumper assembly adds to the front overhang.

Wheelbase
Distance between the center lines of the vehicles front and rear axles.

Inside Turning Radius
Radius of the smallest circle around which the vehicle can turn.

Curb to Curb Turning Radius
Radius of the smallest circle around which the vehicle's tires can turn. This measures assumes a curb height of 9 inches.

Wall to Wall Turning Radius
Radius of the smallest circle around which the vehicle's tires can turn. This measures takes into account any front overhang due to chassis , bumper extensions and or aerial devices. 762
AGENDA ITEM NO. 28.

JROGHQVWDWHĆUHFRP

PRODUCT

WARRANTIES
Exhibit “C”
4 763
AGENDA ITEM NO. 28.

Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 2/8/2010 WA0008

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.

This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

No specific exclusions apply
Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4
Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

Fire and Rescue Apparatus
Coverage:

One (1) Year Material and Workmanship
Basic Apparatus
Twelve (12) months.Warranty Period
Ends After:

The date the apparatus is placed in service, or 60 days from the original buyer invoice date, whichever comes first.Warranty Begins:

Portions of the apparatus manufactured by Pierce shall be free from defects in material and workmanship
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.

3. BUYER'S EXCLUSIVE REMEDY.
764
AGENDA ITEM NO. 28.

Fire and Rescue Apparatus
Coverage:

Three (3) Year Material and Workmanship
Velocity and Impel Custom Chassis
Limited Warranty Limited Warranty Limited Warranty Limited Warranty Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

Portions of the apparatus manufactured by Pierce shall be free from defects in material and workmanship

1. LIMITED WARRANTY
(b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; The date the apparatus is placed in service, or 60 days from the original buyer invoice date, whichever comes first. Warranty Begins:

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This limited warranty applies, where applicable, to Goldstar lamination, defroster heater coil and motor blower assembly (excluding the FET PWM module), heater, air conditioning condenser coil and fan/motor assembly, air conditioning evaporator coil and motor blower assembly (excluding the drain pan pump and thermostat), under seat heaters coil and motor blower assembly (excluding the FET PWM module),
HVAC electronic switches, HVAC hoses and hard lines,
heater water valve, Pierce PS6 seat frames and hardware, Pierce One-Eleven mirrors, Pierce hands-free scba holder, cracking or color loss of roto-molded components, Meritor rear axle, Wabco ABS system, cab door handles, Standen
spring suspension components, and the gauge instrument
cluster.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGE S.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE
POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

3. BUYER'S EXCLUSIVE REMEDY.
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce.

Three (3) Years, or
30,000 Miles, or
5000 Engine Hours
Warranty Period
Ends After:

ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

Cummins Warranty
Worldwide
Fire Apparatus/Crash Trucks
766
AGENDA ITEM NO. 28.

Coverage
Products Warranted
This Warranty applies to new diesel Engines sold by
Cummins and delivered to the first user on or after
April 1, 2007, that are used in fire apparatus truck and crash truck* applications Worldwide.

Base Engine Warranty
The Base Engine Warranty covers any failures of the
Engine which result, under normal use and service,
from a defect in material or factory workmanship
(Warrantable Failure). This Coverage begins with the
sale of the Engine by Cummins and ends five years or
100,000 miles (160,935 kilometers), whichever occurs
first, after the date of delivery of the Engine to the first user .

Engine aftertreatment components included in the
Cummins Critical Parts List (CPL) and marked with a
Cummins part number are covered under Base Engine
Warranty.

Additional Coverage is outlined in the Emission
Warranty section.

These Warranties are made to all Owners in the
chain of distribution and Coverage continues to all
subsequent Owners until the end of the periods of
Coverage.

Cummins
Responsibilities
Cummins will pay for all parts and labor needed to
repair the damage to the Engine resulting from a
Warrantable Failure.

Cummins will pay for the lubricating oil, antifreeze,
filter elements, belts, hoses and other maintenance
items that are not reusable due to the Warrantable
Failure.

Cummins will pay for reasonable labor costs for
Engine removal and reinstallation when necessary to
repair a Warrantable Failure.

Cummins will pay reasonable costs for towing a
vehicle disabled by a Warrantable Failure to the
nearest authorized repair location. In lieu of the towing expense, Cummins will pay reasonable costs for
mechanics to travel to and from the location of the
vehicle, including meals, mileage and lodging when
the repair is performed at the site of the failure.

Owner
Responsibilities
Owner is responsible for the operation and
maintenance of the Engine as specified in Cummins
Operation and Maintenance Manuals. Owner is also
responsible for providing proof that all recommended
maintenance has been performed.

Before the expiration of the applicable Warranty,
Owner must notify a Cummins distributor ,authorized
dealer or other repair location approved by Cummins
of any Warrantable Failure and make the Engine
available for repair by such facility. Except for Engines disabled by a Warrantable Failure, Owner must also
deliver the Engine to the repair facility.

Service locations are listed on the Cummins Worldwide
Service Locator at cummins.com.

Owner is responsible for the cost of lubricating oil,
antifreeze, filter elements and other maintenance items provided during Warranty repairs unless such items
are not reusable due to the Warrantable Failure.

Owner is responsible for communication expenses,
meals, lodging and similar costs incurred as a result of a Warrantable Failure.

Owner is responsible for non-Engine repairs and for
‘‘downtime’’expenses, cargo damage, fines, all
applicable taxes, all business costs and other losses
resulting from a Warrantable Failure.

Owner is responsible for a $100 (U.S. Dollars)
deductible per each service visit under this plan in the 3rd, 4th and 5th years of Base Engine Warranty. The
deductible will not be charged during the first 2 years of the Base Engine Warranty.

Limitations
Cummins is not responsible for failures or damage
resulting from what Cummins determines to be abuse
or neglect, including, but not limited to: operation
without adequate coolants or lubricants; overfueling;
overspeeding; lack of maintenance of lubricating,
cooling or intake systems; improper storage, starting,
warm-up, run-in or shutdown practices; unauthorized
modifications of the Engine.

Any unauthorized modifications to the aftertreatment
could negatively effect emissions certification and void Warranty.

Cummins is also not responsible for failures caused by
incorrect oil, fuel or diesel exhaust fluid or by water , dirt or other contaminants in the fuel, oil or diesel
767
AGENDA ITEM NO. 28.
exhaust fluid.

This Warranty does not apply to accessories supplied
by Cummins which bear the name of another
company. Such non-warranted accessories include, but
are not limited to: alternators, starters, fans, air
conditioning compressors, clutches, filters,
transmissions, torque converters, vacuum pumps,
power steering pumps, fan drives and air compressors.

Cummins branded alternators and starters are covered
for the first two years from the date of delivery of the Engine to the first user ,or the expiration of the Base Engine Warranty, whichever occurs first.

Failures resulting in excessive oil consumption are not covered beyond the duration of the Coverage or
100,000 miles (160,935 kilometers) or 7,000 hours from
the date of delivery of the Engine to the first user ,
whichever of the three occurs first. Before a claim for excessive oil consumption will be considered, Owner
must submit adequate documentation to show that
consumption exceeds Cummins published standards.

Failures of belts and hoses supplied by Cummins are
not covered beyond the first year from the date of
delivery of the Engine to the first user or the duration of the Warranty, whichever occurs first.

Parts used to repair a Warrantable Failure may be new
Cummins parts, Cummins approved rebuilt parts or
repaired parts. Cummins is not responsible for failures resulting from the use of parts not approved by
Cummins.

A new Cummins or Cummins approved rebuilt part
used to repair a Warrantable Failure assumes the
identity of the part it replaced and is entitled to the remaining Coverage hereunder .

Cummins Inc. reserves the right to interrogate
Electronic Control Module (ECM) data for purposes of
failure analysis.

CUMMINS DOES NOT COVER WEAR OR WEAROUT
OF COVERED PARTS.

CUMMINS IS NOT RESPONSIBLE FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES.

THIS W ARRANTYAND THE EMISSION W ARRANTY

SET FORTH HEREINAFTER ARE THE SOLE

W ARRANTIESMADE BY CUMMINS IN REGARD TO
THESE ENGINES. CUMMINS MAKES NO OTHER

W ARRANTIES,EXPRESS OR IMPLIED, OR OF

MERCHANT ABILITYOR FITNESS FOR A
P ARTICULARPURPOSE.

This Warranty gives you specific legal rights, and you
may also have other rights which vary from state to
state.

Emission
Warranty
Products Warranted
This Emission Warranty applies to new Engines
marketed by Cummins that are used in the United
States** in vehicles designed for transporting persons
or property on a street or highway. This Warranty
applies to Engines delivered to the first user on or after September 1, 1992.

Coverage
Cummins warrants to the first user and each
subsequent purchaser that the Engine is designed,
built and equipped so as to conform at the time of sale by Cummins with all U.S. federal emission regulations
applicable at the time of manufacture and that it is free from defects in material or factory workmanship which
would cause it not to meet these regulations within the longer of the following periods: (A) Five years or
100,000 miles (160,935 kilometers) of operation,
whichever occurs first, as measured from the date of
delivery of the Engine to the first user or (B) The Base Engine Warranty.

If the vehicle in which the Engine is installed is
registered in the state of California, a separate
California Emission Warranty also applies.

Limitations
Failures, other than those resulting from defects in
material or factory workmanship, are not covered by
this Warranty.

Cummins is not responsible for failures or damage
resulting from what Cummins determines to be abuse
or neglect, including, but not limited to: operation
without adequate coolants or lubricants; overfueling;
overspeeding; lack of maintenance of lubricating,
cooling or intake systems; improper storage, starting,
warm-up, run-in or shutdown practices; unauthorized
modifications of the Engine.

Any unauthorized modifications to the aftertreatment
could negatively effect emissions certification and void Warranty.

Cummins is also not responsible for failures caused by
incorrect oil, fuel or diesel exhaust fluid or by water , dirt or other contaminants in the fuel, oil or diesel
exhaust fluid.

Cummins is not responsible for non-Engine repairs,
‘‘downtime’’expenses, cargo damage, fines, all
applicable taxes, all business costs or other losses
resulting from a Warrantable Failure.
768
AGENDA ITEM NO. 28.

Cummins Inc.

Box 3005
Columbus, IN 47202-3005
U.S.A.

Bulletin 3381161
Printed in U.S.A. Rev. 08/09
©2001 Cummins Inc.

CUMMINS IS NOT RESPONSIBLE FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES.
* Airport operated crash trucks and fire department
operated trucks employed to respond to fires,
hazardous material releases, rescue and other
emergency-type situations.
** United States includes American Samoa, the
Commonwealth of Northern Mariana Islands, Guam,
Puerto Rico and the U.S. Virgin Islands.

Cummins Inc.

Box 3005
Columbus, IN 47202-3005
U.S.A.

Bulletin 3381161
Printed in U.S.A. Rev. 08/09
/H230052001 Cummins Inc.
769
AGENDA ITEM NO. 28.
770
AGENDA ITEM NO. 28.
771
AGENDA ITEM NO. 28.
772
AGENDA ITEM NO. 28.
773
AGENDA ITEM NO. 28.

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

3. BUYER'S EXCLUSIVE REMEDY.

Fire and Rescue Apparatus
Coverage:

Lifetime Fifty (50) Year Structural Integrity
Chassis Frame & Crossmembers
Fifty (50) Years
(Expected Life of Apparatus)
Warranty Period
Ends After:

The date of the original purchase invoice (issued when the product ships from the factory).Warranty Begins:

Custom chassis frame rail and cross members manufactured by Pierce shall be free from defects in material and
workmanship
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This warranty does not apply to damage caused by corrosion.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4
774
AGENDA ITEM NO. 28.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This limited warranty excludes brake pads, brake rotors, seal boots and shock absorbers.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGE S.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE
POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

Three (3) Years
-or-
30,000 Miles
Warranty Period
Ends After:

ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

Fire and Rescue Apparatus
Coverage:

Three (3) Year Material and Workmanship
TAK-4 Independent Front Suspension
Limited Warranty Limited Warranty Limited Warranty Limited Warranty Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

The TAK-4 Front Independent Suspension and Steering
Gears shall be free from defects in material and
workmanship.

1. LIMITED WARRANTY
(b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:
775
AGENDA ITEM NO. 28.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This limited warranty excludes brake shoes, brake drums, ball joint boots and shock absorbers.