Clovis City Council
July 7, 2025

PUMP
Pump will be a Pierce, low profile,
2000
gpm single stage midship mounted centrifugal type,
mounted below the cab. The pump will have a
15 percent reserve capacity to allow for extended
time between pump rebuild. To ensure efficient pump/vehicle design the capacity to weight ratio will not be less than

1.5:1
.

The pump casing will consist of three (
3 ) discharge outlets, one (
1 ) to each side in line with the
impeller and one (
1 ) to the rear. The pump casing will incorporate two ( 2 ) water strippers to
maintain radial balance.

Pump will be the Class A type.

Pump will be certified to deliver the percentage of rated discharge from draft at pressure indicated below:
100
percent of rated capacity at
150
psi net pump pressure
70 percent of rated capacity at
200
psi net pump pressure
50 percent of rated capacity at
250
psi net pump pressure
The pump will have the capacity to deliver the percentage of rated discharge from a pressurized source as indicated below:
135
percent of rated capacity at
100
psi net pump pressure from a
5 psi source
Pump body will be fine-grained gray iron. Pump will incorporate a heater/cooling jacket integral to the pump housing.

The impeller will be high strength vacuum cast bronze alloy accurately machine balanced and splined to a ten
10 ) spline stainless steel pump shaft for precision fit, exceptional durability, and efficiency. Double replaceable reverse flow labyrinth type bronze wear ring design will help to minimize end thrust. The impeller will be a twisted vane design to create higher lift. No keyed shafts will be acceptable.

The pump will include o-ring gaskets throughout the pump.

Deep groove radial type oversize ball bearings will be provided. The bearings will be protected at the openings from road dirt and water with an oil seal and water slinger.

The pump will have a flat, patterned area on the top of the pump intake wye to allow standing for plumbing maintenance. The main inlet manifold will be

6.00 " in diameter and will have a low
profile design to facilitate low crosslays and high flows.

For ease of service, the pump housing, intake wye, impeller, mechanical seal, and gear case will be accessible from above the chassis frame by tilting the cab. Removal of the main inlet wyes will provide access to the impeller, mechanical seal, and wear ring.

The tank to pump line and the primary discharge line will be the only piping required to be removed for overhaul.

For ease of service and overhaul there will be no piping or manifolding located directly over the pump.

PUMP MOUNTING
Pump will be mounted to the chassis frame rails directly below the crew cab, to minimize wheelbase and facilitate service, using rubber isolators in a modified V pattern that include one (
1 ) central mounted isolator located between the frame rails and one ( 1 ) on each side outside the
frame rails. The mounting will allow chassis frame rails to flex independently without damage to the fire pump. Each isolator will be

2.55 " in total outside diameter and will be rated at
490
lb. The
pump will be completely accessible by tilting the cab with no piping located directly above the pump.
0515822
Seal, Mechanical, Silicon Carbide,
PUC Pump

MECHANICAL SEALS
Silicon carbide mechanical seals will be provided. The seals will be spring loaded and self- adjusting. The seals will have a minimum thermal conductivity of 126
W/m*K to run cooler. Seals
will have a minimum hardness of
2800
kg/mm
2 to be more resistant to wear, and have thermal
expansion characteristics of no more than

4.0 X
106
mm/mm*K to be more resistant to thermal
shock.
0802234
Gear Case, Integrated Pump
Transmission, PUC-NG, Cummins

PUMP GEAR CASE
The integrated pump transmission gear case will use a pressure-lubricated system to cool, lubricate, and filter the oil. The gear case will be constructed of lightweight aluminum, and impregnated with resin in accordance to MIL Spec MIL-I- 17563
. A sight glass, accessible by tilting
the cab, will be provided for easy fluid level checks.

The gear case will consist of three (
3 ) gears to drive the pump.

CLUTCH
There will be a heavy-duty hydraulic clutch mounted directly to the integrated pump transmission to engage and disengage the pump without gear clash. The clutch will be a multiple disc design for maximum torque. The clutch will be fully self-adjusting to provide automatic wear compensation, and consistent torque throughout the life of the clutch. Positive engagement and disengagement will be provided through a high efficient and dependable hydraulic system to assure superior performance.

LOW PRESSURE/HIGH TEMPERATURE LIGHTS
Lights will be provided to indicate when a high temperature or low pressure situation occurs.

Lights will be provided next to the master gauges at the pump panel as well as on the control panel in the cab. A pair of lights will be provided in each location. One ( 1 ) light will be provided to
indicate high temperature. The second light will be provided to indicate a low pressure. All lights will be labeled accordingly.
50 972
Bid #:
888
AGENDA ITEM NO. 28.
0721196
Pumping Mode, Pump and
Roll/Stationary, Basic, MUX, PUC

PUMPING MODE
Pump will provide for both pump and roll mode and stationary pumping mode.

Stationary pumping mode will be accomplished by stopping the vehicle, setting the parking brake and engaging the water pump switch on the cab switch panel. The transmission will shift to "Neutral" range automatically when the parking brake is set. The "OK to Stationary Pump" indicator will also illuminate when the parking brake is set.

If the vehicle is equipped with a suitable Husky foam system or Hercules CAFS system, these systems will be engaged from the cab switch panel as well. pump and roll mode will be accomplished by the use of the main pump and will not require the use of a secondary pump. pump and roll mode will use the same operation sequence as stationary pumping mode with a few additional steps. After the vehicle is setup for stationary pumping, the operator will leave the cab and setup the pump panel to discharge at the desired outlet(s). Upon returning to the cab, the operator will disengage the parking brake. An "OK to pump and roll" indicator will illuminate on the cab switch panel. First gear on the transmission gear selector will be selected by the operator for pump and roll operations. The operator as needed will apply the foot throttle. pump and roll mode will be maintained unless the transmission shifts out of first gear.

Stopping either stationary pumping mode or pump and roll mode will be accomplished by pressing the "Water Pump" switch down to disengage the pump.

A pump pressure reading will be displayed in view of the driver. 0658980
Pump Shift, Sure-Shift, Additional
Switch, Pump Operator's Panel

PUMP SHIFT
Pump will be engaged in not more than two steps, by simply setting the parking brake, which will automatically put the transmission into neutral, and activating a rocker switch in the cab. Switches in the cab will also allow for water, foam, or CAFS if equipped, and activate the appropriate system to preset parameters. The engagement will provide simple two-step operation, enhance reliability, and completely eliminate gear clash. The shift will include the indicator lights as mandated by NFPA. A direct override switch will be located behind a door in the pump operator's panel. The switch will automatically disengage when the door is closed.

As the parking brake is applied, the pump panel throttle will be activated and deactivate the chassis foot throttle for stationary operation.

An additional pump activation switch will be provided at the pump operator's panel to engage the pump. A switch guard will be installed to prevent accidental switch activation. Indicator lights will be provided to show that the pump is in gear.
0515833
Transmission Lock-up, Not Req'd,
Park to Neutral, Pump, PUC

TRANSMISSION LOCK UP
Transmission lock up is not required as transmission will automatically shift to neutral as soon as the parking brake is set.
0515835
Auxiliary Cooling System, PUC

AUXILIARY COOLING SYSTEM
A supplementary heat exchange cooling system will be provided to allow the use of water from the discharge side of the pump for cooling the engine water. A water-to-coolant heat exchanger will be used.
0014486
Not Required, Transfer Valve, Single
Stage Pump
0746508
Valve(s), Relief Intake, Trident Air
Max, Control Location

INTAKE RELIEF VALVE
One (
1 )
Trident Air Max intake relief valve(s) will be installed on the suction side of the pump preset at
200
psig
.

The relief valve will have a working range of
50 psi to
350
psi.

The outlet will terminate below the frame rails with a

2.50 " National Standard hose thread adapter
and will have a "do not cap" warning tag.

One (
1 ) adjustable air regulator and pressure indicating gauge will be located on a common bezel on the left side pump panel
to control the intake valve(s).
51 972
Bid #:
889
AGENDA ITEM NO. 28.
0724463
Controller, Pressure, Pierce LCD ,
PUC

PIERCE PRESSURE CONTROLLER
A Pierce electronic pressure controller will be provided.

A pressure transducer will be installed in the discharge side of the water pump. The transducer continuously monitors pump pressure sending a signal to the electronic pressure controller.

The pressure controller can be used in two (
2 ) modes of operation, RPM mode and pressure
modes. The controller will be programmed to turn on/default to No Mode/Default Press Setting

mode.

In the RPM mode, the controller can be activated after vehicle parking brake has been set. When in this mode, the controller will maintain the set engine speed, regardless of engine load (within engine operation capabilities).

In the pressure mode, the controller can be activated after vehicle parking brake has been set.

When in this mode, the controller will automatically maintain the discharge pressure set by the operator (within the discharge capabilities of the pump and water supply) regardless of flow.

A

2.00 " diameter throttle control knob with no mechanical stops, a serrated grip, and a red idle push button in the center will be a integrated/part of the pressure controller. The throttle control knob will be programmed for
Clockwise
rotation to increase engine speed.

Individual LED indicators for ok to pump, throttle ready, pressure mode and rpm mode will be located on the pressure controller for easy viewing.

A pump cavitation protection feature will also be provided which will return the engine to idle should the pump cavitate. Cavitation is sensed by the combination of pump pressure below 30 psi
and engine speed above
2000
rpm for more than five (
5 ) seconds.

Other safety features include recognition of low water and no water conditions with an automatic programmed response and a push button to return the engine to idle.

The pressure controller LCD screen will be

4.20 " in size with a minimum brightness of
750
nits.

The LCD screen and LED intensity will automatically adjust for day and nighttime operation. The LCD screen intensity can also be manually adjusted if needed.

The following information will be provided/displayed on the LCD screen:

Engine RPM
Check engine and stop engine warning indicators
Engine oil pressure
Engine coolant temperature
Water pump transmission temperature
Fuel Level
Water tank level
Battery voltage
Operating mode (RPM or pressure)
Pressure or RPM setting
On screen messaging show diagnostic and warning messages as they occur. It will show apparatus information, stored data, and program options when selected by the operator. It will monitor inputs outputs and support audible and visual warning alarms for the following conditions:

High battery voltage
Low battery voltage/engine off
Low battery voltage/engine running
High water pump temperature
Low fuel
Low engine oil pressure
High engine coolant temperature
Water tank out of water (visual alarm only)
No engine response (visual alarm only)
The pressure controller will store the accumulated operating hours for the pump and engine.

These items are to be displayed within the pressure controller menu.

The pressure controller will include a USB port on the back of the controller for easy software upgrades if needed.
0072153
Primer, Trident, Air Prime, Air
Operated

PRIMING PUMP
The priming pump will be a Trident Emergency Products compressed air powered, high efficiency, multistage venturi based AirPrime System, conforming to standards outlined in the current edition of applicable NFPA standards.

All wetted metallic parts of the priming system are to be of brass and stainless steel construction.

One (
1 ) priming control will open the priming valve and start the pump primer. 0044552
Line, 0.50" Recirculating w/Check
Valve

RECIRCULATING LINE WITH CHECK VALVE
A

0.50 " diameter recirculating line, from the pump to the water tank, will be furnished with a control installed at the pump operator's control panel. A check valve will be provided in this line to prevent the back flow of water from the tank to the pump if the valve is left in the open position. 0895331
SP
Thermal Relief Valve 140, w/Amber
Warning Light and Alarm, PUC Pump

THERMAL RELIEF VALVE
A Pierce thermal relief valve will be included on the pump that monitors pump water temperature and opens to relieve water to cool the pump when the temperature of the pump water exceeds 140
Degrees F.

The thermal protection system will include a amber warning light and audible alarm mounted on the pump operator panel.

The discharge line will be
3/8
inch diameter tubing plumbed to
ground
.
0780359
Manuals, Pump, (2) Total, Electronic
Copies, Pierce PUC Pump

PUMP MANUALS
There will be a total of two (
2 ) pump manuals provided by the pump manufacturer and furnished with the apparatus. The manuals will be provided by the pump manufacturer in the form of two ( 2 )
electronic copies. Each manual will cover pump operation, maintenance, and parts. 52 972
Bid #:
890
AGENDA ITEM NO. 28.
0602496
Plumbing, Stainless Steel and Hose,
Single Stage Pump, PUC

PLUMBING, STAINLESS STEEL AND HOSE
All inlet and outlet lines will be plumbed with either stainless steel pipe, flexible polypropylene tubing or synthetic rubber hose reinforced with hi-tensile polyester braid. All hose's will be equipped with brass or stainless steel couplings. All stainless steel hard plumbing will be a minimum of a schedule
10 wall thickness.

Where vibration or chassis flexing may damage or loosen piping or where a coupling is required for servicing, the piping will be equipped with victaulic or rubber couplings.

Plumbing manifold bodies will be ductile cast iron or stainless steel.

All piping lines are to be drained through a master drain valve or will be equipped with individual drain valves. All drain lines will be extended with a hose to drain below the chassis frame.

All water carrying gauge lines will be of flexible polypropylene tubing.

All piping, hose and fittings will have a minimum of a
500
PSI hydrodynamic pressure rating.
0795135
Plumbing, Stainless Steel, w/Foam
System

FOAM SYSTEM PLUMBING
All piping that is in contact with the foam concentrate or foam/water solution will be stainless steel. The fittings will be stainless steel or brass. Cast iron pump manifolds will be allowed. 0517852
Inlets, 6.00" - 1250-2000 GPM,
Pierce PUC Pump

MAIN PUMP INLETS
A

6.00 " pump manifold inlet will be provided on each side of the vehicle. The suction inlets will include removable die cast zinc screens that are designed to provide cathodic protection for the pump, thus reducing corrosion in the pump.

Main pump inlets will not be located on the main operator's panel and will maintain a low connection height by terminating below the top of the chassis frame rail. 0812671
Valve, w/Relief, LS Main Inlet, 6",
Elec, Akron 9333 Cont, w/O-ride,PUC

INLET BUTTERFLY VALVE
One (
1 ) high performance butterfly valve will be provided on the left side main pump inlet.

The

6.00 " inlet valve will be provided with a
Akron Style
53 built-in, adjustable pressure relief
valve preset at
125
psig
and a bleeder valve will be provided on the inlet side of the valve.

There will be an Akron
9333
electric valve controller provided on the pump operators panel. The electric control must be of a true position feedback design, requiring no clutches in the motor or current limiting. The unit must be completely sealed with momentary open, close as well and an optional one touch full open feature to operate the valve actuator. The controller will provide position indication on a full color, backlit LCD display. It will have manual adjustment of the brightness as well as an auto dimming option.

A manual override hex nut will be provided directly on the inlet valve. Access to the manual override hex nut will be provided with a hole thru the left side lower pump panel. The hole in the left pump panel will allow the use of a speed wrench and/or ratchet with a socket to be used on the valve override hex nut if needed.

A maintain switch will be provided near the manual override. The switch will cut off power to the valve to allow for manual override valve actuation.

A one piece speed wrench will be provided in loose equipment for manually overriding the valve.

The speed wrench will have sockets welded on each end for overriding the valve. 0004646
Cap, Main Pump Inlet, Long Handle,

NST, VLH

MAIN PUMP INLET CAP
The main pump inlets will have National Standard Threads with a long handle chrome cap.

The cap will be the Pierce VLH, which incorporates an exclusive thread design to automatically relieve stored pressure in the line when disconnected.
0084610
Valves, Akron 8000 series- All

VALVES
All ball valves will be Akron® Brass. The Akron valves will be the 8000
series heavy-duty style
with a stainless steel ball and a simple two-seat design. No lubrication or regular maintenance is required on the valve.

Valves will have a
ten (
10 ) year
warranty.
0520002
Valve, Inlet(s) Recessed, Side Cntrl,
PUC
The location of the valve for the
two (2) inlets
will be recessed behind the pump panel.
0004700
Control, Inlet, at Valve

INLET CONTROL
The side auxiliary inlet(s) will incorporate a quarter-turn ball valve with the control located at the inlet valve. The valve operating mechanism will indicate the position of the valve. 0004660
Inlet (1), Left Side, 2.50"

LEFT SIDE INLET
There will be one (
1 ) auxiliary inlet with a

2.50 " valve at the left side pump panel, terminating with a

2.50 " (F) National Standard hose thread adapter.

The auxiliary inlet will be provided with a strainer, chrome swivel and plug. 0004680
Inlet, Right Side, 2.50"

RIGHT SIDE INLET
There will be one (
1 ) auxiliary inlet with a

2.50 " valve at the right side pump panel, terminating
with a

2.50 " (F) National Standard hose thread adapter.

The auxiliary inlet will be provided with a strainer, chrome swivel and plug. 53 972
Bid #:
891
AGENDA ITEM NO. 28.
0521137
Anode, Zinc, Pair, Pump Inlets, PUC

ANODE, INLET
A pair of sacrificial zinc anodes will be provided in the water pump inlets to protect the pump from corrosion.
0897252
Inlet, 4" to 6" Front, 5" Plumbing,
w/Bleeder Valve, California Style

FRONT INLET
A

4.50 " inlet
front inlet that terminates on the right side bumper extension with a "California" style

8.00 " wide notch
will be provided.

The plumbing will consist of

5.00 "
stainless steel
and a

5.00 " Jamesbury butterfly valve
. Only
radius elbows will be used in the piping, no mitered joints.

Drains will be furnished in all the low points of piping and have .
75 " valves with T swing handle.

Bleeder valves will be located near the threaded connection and the valve control.

Die cast zinc screens will be provided at the front inlet connection. 0767497
Control, Front Inlet, Akron 9333 Elec
Controller, w/Override, PUC,
Disconnect Sw

FRONT INLET CONTROL
The front inlet will be gated and controlled with an Akron 9333
electric valve controller provided
on the pump operators panel. The electric control must be of a true position feedback design, requiring no clutches in the motor or current limiting. The unit must be completely sealed with momentary open, close as well and an optional one touch full open feature to operate the valve actuator. The controller will provide position indication on a full color, backlit LCD display. It will have manual adjustment of the brightness as well as an auto dimming option.

A manual override hex nut will be provided directly on the valve. Access to the manual override hex nut will be between the lower pump panel and the rearward area of the cab on the right side of the truck.

A maintain switch will be provided on the lower right PUC pump panel near the manual override hex nut to disconnect the power to the electric actuator motor to allow the manual override to be utilized.

A manual override speed wrench with swivel sockets will be provided in loose equipment to override the front inlet valve.
0737985
Valve, Relief Intake,Front Inlet,Trident
Air Max,Cntrl w/Main Pump Intake
Relief

INTAKE RELIEF VALVE, FRONT INLET
A Trident Air Max intake relief valve will be installed on the inlet side of the front inlet valve.

The relief valve will have a working range of
50 PSI to
350
PSI.

The outlet will terminate below the frame rails with a

2.50 " National Standard hose thread adapter
and will have a "do not cap" warning tag.

The control for this front inlet intake relief valve will be operated with the main pump Trident Air Max intake relief valve controls.
0769000
Piping to Terminate in Hose Tray, As
Short As Possible

FRONT INLET PIPING
The piping for the front inlet will terminate with a chrome plated National Standard hose thread adapter, within the front hose tray so that the adapter threads protrude just far enough to allow a hose coupling to be installed.
0521688
Not Required, Cap, Long Handle,
Front Inlet, Pre-connected Hose

0092569
No Rear Inlet (Large Dia) Requested

0064116
No Rear Inlet Actuation Required

0092696
Not Required, Cap, Rear Inlet

0009648
No Rear Intake Relief Valve Required
on Rear Inlet
0092568
No Rear Auxiliary Inlet Requested

0723049
Valve, .75" Bleeder, Aux. Side Inlet,
"T" Swing Handle

INLET BLEEDER VALVE
A

0.75 " bleeder valve will be provided for each side gated inlet.

The valves will be located behind the panel with a "T" swing style handle control extended to the outside of the panel.

The handles will be chrome plated and provide a visual indication of valve position. The swing handle will provide an ergonomic position for operating the valve without twisting the wrist and provides excellent leverage.

The water discharged by the bleeders will be routed below the chassis frame rails. 54 972
Bid #:
892
AGENDA ITEM NO. 28.
0520277
Tank to Pump, (1) 3.00" Valve, 4.00"
Plumbing, PUC

TANK TO PUMP
The booster tank will be connected to the intake side of the pump with heavy duty

4.00 " piping
and a quarter turn

3.00 " full flow line valve with the control located at the operator's panel. A rubber coupling will be included in this line to prevent damage from vibration or chassis flexing.

A check valve will be provided in the tank to pump supply line to prevent the possibility of "back filling" the water tank.
0595508
Outlet, Tank Fill, 1.50", PUC

TANK REFILL
A

1.50 " combination tank refill and pump re-circulation line will be provided, using a quarter-turn full flow ball valve controlled from the pump operator's panel. 0766941
Control, Outlets, Swing Handle, Elec
Right Outlets Akron 9335 w/Press
Disp, PUC

DISCHARGE OUTLET CONTROLS
The right side discharges will incorporate a quarter-turn ball valve and be controlled by Akron 9335
electric valve controllers provided on the pump operators panel. The electric controls must be of a true position feedback design, requiring no clutches in the motor or current limiting. The units must be completely sealed with momentary open, close as well and an optional one touch full open feature to operate their corresponding valve actuator. The controllers will provide position indication on a full color, backlit LCD display. They will have manual adjustment of the brightness as well as an auto dimming option. In addition to the valve controls, the electric valve controllers will include a pressure display
All other outlets will have manual swing handles that operate in a vertical up and down motion.

These handles will be able to lock in place to prevent valve creep under pressure. 0516755
Outlet, Left Side, 2.50" (2), PUC

LEFT SIDE DISCHARGE OUTLETS
There will be two (
2 ) discharges with a

2.50 " valves on the left side of the apparatus, terminating with a

2.50 " (M) National Standard hose thread adapter. Discharges will be located below the cab, and will be no higher than the top of the chassis frame rail. Discharges will not be located on the pump operator's panel. Lever controls will be provided at the valve. 0055095
Not Required, Elbow, Left Side
Outlets, 2.50"
0092570
Not Required, Outlets, Left Side
Additional
0035094
Not Required, Elbow, Left Side
Outlets, Additional
0766761
Outlet, Right Side, 2.50", (1), Electric
Akron 9335 Controller, PUC

RIGHT SIDE DISCHARGE OUTLETS
One (
1 ) discharge outlet
with a

2.50 " valve will be provided on the right side of the apparatus, terminating with a

2.50 " MNST adapter. The discharge(s) will be located below the crew cab and will be no higher than the top of the chassis frame rail.

There will be Akron
9335
electric valve controller(s) provided on the pump operators panel. The electric control(s) must be of a true position feedback design, requiring no clutches in the motor or current limiting. The unit(s) must be completely sealed with momentary open, close as well and an optional one touch full open feature to operate the valve actuator. The controller(s) will provide position indication on a full color, backlit LCD display. They will have manual adjustment of the brightness as well as an auto dimming option.

In addition to valve position, each controller will include a pressure display. 0021134
Not Required, Elbow, Right Side
Outlets, 2.50"
0092571
Not Required, Outlets, Right Side
Additional
0089584
Not Required, Elbow, Right Side
Outlets, Additional
0818640
Outlet, Large Diameter, Right Side,
Akron Valve, PUC

LARGE DIAMETER DISCHARGE OUTLET
There will be an Akron
8800

4.00 " flat ball valve with

4.00 " plumbing
terminating with a

4.00 "
MNST chrome
adapter on the right side pump panel.

The valve will be controlled with a(n)
Akron
9335
with pressure
located at the pump operator's
panel.
55 972
Bid #:
893
AGENDA ITEM NO. 28.
0820228
Elbow and Cap, Large Dia Outlet,
Provided by Fire Department,
NFPA/ULC 2024

LARGE DIAMETER OUTLET ELBOW/CAP PROVIDED BY FIRE DEPARTMENT NFPA
1900
,
2024
edition, section

13.7.7 and CAN/ULC S
515:2024
edition, section

5.2 , requires
any

2.00 " or larger discharge outlet that is located more than

42.00 " off the ground and to which
hose is to be connected and that is not in a hose storage area will be supplied with a sweep elbow of at least
30 degrees downward.

NFPA
1900
,
2024
edition, section

13.7.4 and CAN/ULC S
515:2024
edition, section

5.2 , requires
all discharge outlet connections, except connections to which a hose will be pre-connected, will be equipped with caps or closures capable of withstanding a hydrostatic gauge pressure of 100

psi over the maximum pump close-off pressure or
500
psi, whichever is greater.

The elbow(s) and cap are not on the apparatus as manufactured. The fire department will provide the elbow(s) and cap.
0649939
Outlet, Front, 1.50" w/2" Plumbing

FRONT DISCHARGE OUTLET
There will be one (
1 )

1.50 " discharge outlet piped to the front of the apparatus and located on the
top of the left side of the front bumper
.

Plumbing will consist of

2.00 " piping and flexible hose with a

2.00 " ball valve with control at the
pump operator's panel. A fabricated weldment made of stainless steel pipe will be used in the plumbing where appropriate. The piping will terminate with a

1.50 " NST with
90 degree stainless
steel swivel
.

There will be
T swing handle
drains provided at all low points of the piping.
0516777
Outlet, Rear, 2.50", (1), Thru Tank,
PUC

REAR DISCHARGE OUTLET
One (
1 ) discharge outlet
will be piped to the rear of the hose bed on
left side
, installed so proper
clearance is provided for spanner wrenches or adapters. Plumbing will consist of

2.50 " piping
along with a

2.50 " full flow ball valve with the control from the pump operator's panel. Discharge will terminate with

2.50 " NST thread. Discharge piping will be schedule
10 304
L welded or formed
stainless steel and routed through the water tank.
0045091
Elbow, Rear Outlets, 45 Degree,

2.50" FNST x 2.50" MNST, VLH

REAR OUTLET ELBOWS
The

2.50 " discharge outlets located at the rear of the apparatus will be furnished with a

2.50 " (F)
National Standard hose thread x

2.50 " (M) National Standard hose thread, chrome plated, 45 degree elbow.

The elbow will be Pierce VLH, which incorporates an exclusive thread design to automatically relieve stored pressure in the line when disconnected.
0537394
Not Required, Outlet, Rear,
Additional, PUC

0537395
Not Required, Elbow, Rear Outlets,
Additional
0752078
Caps/Plugs for 1.00" to 3.00"
Discharges/Inlets, S/S Cable

DISCHARGECAPS/ INLET PLUGS
Chrome plated, rocker lug, caps with S/S cables will be furnished for all discharge outlets

1.00 "
thru

3.00 " in size, besides the pre-connected hose outlets.

Chrome plated, rocker lug, plugs with S/S cables will be furnished for all auxiliary inlets

1.00 " thru

3.00 " in size.

The caps and plugs will incorporate a thread design to automatically relieve stored pressure in the line when disconnected.
0723042
Valve, 0.75" Bleeder, Discharges, "T"
Swing Handle

OUTLET BLEEDER VALVE
A

0.75 " bleeder valve will be provided for each outlet

1.50 " or larger. Automatic drain valves are
acceptable with some outlets if deemed appropriate with the application.

The valves will be located behind the panel with a T swing style handle control extended to the outside of the side pump panel.

The handles will be chrome plated and provide a visual indication of valve position.

The T swing handle will provide an ergonomic position for operating the valve without twisting the wrist and provides excellent leverage.

Bleeders will be located at the bottom of the pump panel. They will be properly labeled identifying the discharge they are plumbed in to.

The water discharged by the bleeders will be routed below the chassis frame rails. 0638829
Adapter, Thread - 4.00" FNST X 4.50"
MNST, w/Cap

ADAPTER
There will be
one (
1 ) adapter
with

4.00 " FNST x

4.50 " MNST, chrome, with cap. These adapters
will be installed on
Right side
.
0005080
Reducer, 2.50" FNST x 1.50" MNST,
w/Cap

REDUCER
There will be
one (
1 ) adapter
with

2.50 " FNST x

1.50 " MNST threads and a

1.50 " chrome plated
cap installed on
Rear

2.5 " discharge
.
56 972
Bid #:
894
AGENDA ITEM NO. 28.
0516280
Outlet, 3.00" Deluge w/2.50" Valve,
w/TFT Extend-a-Gun XG18, PUC

DELUGE RISER
A

3.00 " deluge riser will be installed above the pump in such a manner that a monitor can be mounted and used effectively. Piping will be installed securely so no movement develops when the line is charged. The riser will be gated and controlled at the pump operator's panel. A

2.50 "
valve will be provided. The deluge riser will allow flow for 1000
GPM.

TELESCOPIC PIPING
The deluge riser piping will include a

18.00 " Task Force Model XG
18 Extend-A-Gun extension.

This extension will be telescopic to allow the deluge gun to be raised

18.00 " increasing the range
of operation.

A position sensor will be provided on the telescopic piping that will activate the "do not move vehicle" light inside the cab when the monitor is in the raised position. 0095958
Deluge Outlet, Special
Height/Location

DELUGE OUTLET SPECIAL INSTRUCTIONS
The deluge gun outlet will be located
Centered in Dunnage area so that there is no interference with Booster Reel Lines.
.
0770359
No Monitor Requested,
Customer/Dealer Furnished and
Installed

MONITOR
A customer/dealer supplied and installed make and model Apollo Model
3414
monitor will be
properly installed on the deluge riser.
0029304
No Nozzle Req'd

0005070
Deluge Mount, NPT

The deluge riser will have male National Pipe Threads for mounting the monitor. 0750982
Crosslay Module, Full Width, Roll Up
Doors, PUC

CROSSLAY MODULE
The crosslay module will be full width of the rear body.

The forward, upper corners of the module will have full body corners.

The crosslay module will be manufactured for installation of roll up doors on each side. 0750897
Doors, Crosslay, Roll-up Amdor, Each
End, Full Height, PUC

ROLL-UP DOOR, CROSSLAY ENDS, PUC
All compartment doors will be roll-up style double faced, aluminum construction, painted one (
1 )
color to match the lower portion of the body
and manufactured by AMDOR
™.

The crosslay
enclosure will be full width of the body.

The track will be the flanged track with the screws installed to the rear of the track guide.

The slats will be double wall box frame extrusion. The exterior surface will be flat and the interior surface will be concave to help loose equipment fall to the ground and prevent it from jamming the door.

Between each slat will be a PVC inner seal to prevent metal to metal contact and prevent dirt or moisture from entering the compartments.

Each door will have a

4.00 " counter balance to assist in lifting.

A polished stainless steel lift bar with locking key latches to be provided for each roll-up door. The keys to be Model
751
to match all compartment and cab doors
. The lift bar will be located at the
bottom of door with striker latches installed at the base of the side frames. Side frame mounted door strikers will include support beneath the stainless steel lift bar to prevent door curtain bounce, improve bottom seal life expectancy and to avoid false door ajar signals.

The crosslays will
have a drip pan
below the roll of the door.
0747660
Lights, Crosslay Compt, Forward
LED, 2Lts

CROSSLAY COMPARTMENT LIGHTING
There will be two (
2 )
12 volt DC light strips with white LEDs and mechanical fasteners, provide behind the front door frame on the crosslay compartments per the following:

One (
1 ) strip light for the left side crosslay compartment door One (
1 ) strip light for the right side crosslay compartment door The lights will be activated when the battery switch is on and the respective door is opened. 0750916
Crosslays, (2) 1.50", W/Poly Trays,
PUC

LOWER CROSSLAY
There will be two (
2 ) lower crosslays provided.

1.50 " Crosslay
There will be two (
2 )

1.50 " crosslays plumbed with

2.00 " welded or formed schedule
10 304
L
stainless steel pipe.

The crosslays will be low mounted with the bottom of both crosslay trays no more than

11.00 "
above the frame rails for simple, safe reloading and deployment.

There will be a

1.50 " National Standard hose thread
90 -degree swivel provided in each hose bed,
so that the hose may be removed from either side of apparatus. The swivel will be as far outbound as possible for ease of changing hose.

Each crosslay will be gated with a

2.00 " quarter turn ball valve with the controls located at the pump operator's panel.

Each hose bed will be capable of carrying
200
' of

1.75 " double jacket hose
.

Crosslay Hose Tray
A removable tray will be provided for each crosslay hose bed. The crosslay tray will be constructed of black poly to provide a lightweight sturdy tray. Two ( 2 ) hand holes will be in the
floor and additional hand holes will be provided in the sides for easy removal and installation from the compartment. The floor of the trays will be perforated to allow for drainage and hose drying.

Trays will be held in place by a mechanical spring-loaded stainless-steel latch that automatically deploys upon loading the trays to hold the trays in place during transit. 57 972
Bid #:
895
AGENDA ITEM NO. 28.
0744954
Crosslay, (1) 1.50", Deadlay (1),
W/Poly Trays, PUC

UPPER CROSSLAY/DEADLAY
There will be one (
1 ) upper crosslay and one (
1 ) upper deadlay provided.

1.50 " Crosslay
There will be one (
1 )

1.50 " crosslay plumbed with

2.00 " welded or formed schedule
10 304
L
stainless steel pipe.

There will be a

1.50 " National Standard hose thread
90 -degree swivel provided in each hose bed,
so that hose may be removed from either side of apparatus. The swivel will be as far outbound as possible for ease of changing hose.

Each crosslay will be gated with a

2.00 " quarter turn ball valve with the controls located at the pump operator's panel.

Each hose bed will be capable of carrying
200
' of

1.75 " double jacket hose
.

Deadlay
There will be one (
1 ) deadlay, without plumbing provided.

The hose bed will be capable of carrying
200
' of

1.75 " double jacket hose
.

Crosslay Hose Tray
A removable tray will be provided for each crosslay hose bed. The crosslay tray will be constructed of black poly to provide a lightweight sturdy tray. Two ( 2 ) hand holes will be in the
floor and additional hand holes will be provided in the sides for easy removal and installation from the compartment. The floor of the trays will be perforated to allow for drainage and hose drying.

Trays will be held in place by a mechanical spring-loaded stainless-steel latch that automatically deploys upon loading the trays to hold the trays in place during transit. 0724032
SP
Mounting, Backboard, Upper
Crosslay Module, Strap, Special,
PUC

BACKBOARD STORAGE
Mounting will be provide for
One (
1 )
backboard(s) located in the upper crosslay module. The
backboard(s) will be enclosed and removable from either side of the truck. A 2 " Velcro® strap with
a tri-glide buckle will be provided on each end of the storage. A footman's loop will be used on the forward wall. The rearward wall will have a slot cut into it to weave the restraint strap through.

The backboard(s) to be stored will be

1.5 " T x
18 "W x

71.75 " L
.
0791268
MODIFICATION, Increase
Wheelbase 1.00"

0653559
SP
Reel, Booster, Two (2) - Over Pump,
Alum, PUC

BOOSTER HOSE REELS
Two (
2 ) Hannay electric rewind aluminum booster hose reels will be installed over the pump in a recessed open compartment, one each side.

A polished stainless steel roller and guide assembly will be mounted on each side of the apparatus.

Discharge controls will be provided at the pump operator's panel. Plumbing to the reels will consist of

1.50 " Aeroquip hose and a

1.50 " valves.
0896538
SP
Switch, (2) Reel Rewind - Special
Location, Rocker Switch

Reel motor will be protected from overload with a sized automatic reset circuit breaker.

Two (
2 ) Electric rewind controls will be momentary rocker switches installed on In the switch
panel at the pump operator's panel and on the forward wall of RS 3 .
0005305
Hose, Booster - (2) Reels w/150' of

1.00"/800 PSI
Booster hose,

1.00 " diameter and
150
feet long, with chrome plated Barway, or equal, couplings will be provided on each reel.

Working pressure of the booster hose will be a minimum of 800
psi.
0017858
Capacity, Hose Reel 150' of 1"

Capacity of the hose reel will be 150 feet of 1.00" booster hose. 0007428
Nozzle for Booster Reel Not Req'd

0025028
Cutout for Reel Access, Roller
Assembly in Cutout

HOSEREEL ACCESS
A quantity of
two (
2 )
cutout(s) will be provided in the
1 each side of the booster reels in the
forward hatch compartment area.
for the hose reel(s). These cutout(s) will allow access to the hose and provide a window to view the reel. Stainless steel rollers with nylon bushings will be mounted horizontally and vertically around the cutout.
58 972
Bid #:
896
AGENDA ITEM NO. 28.
0617886
SP
Foam Sys, FoamPro 1600, Single
Agent, PUC, Multi Select Feature

FOAM SYSTEM
There will be a Foam Pro, Model
1600
, direct injection foam proportioning system furnished and installed on the apparatus.

The system will be a single agent system suitable for handling Class "A" foam concentrate only.

The foam system will be plumbed to
lower rear crosslay, lower front crosslay, left side of front bumper, hose reel in left side of dunnage area, hose reel in right side of dunnage area and left rear outlet
.

The proportioning operation will use paddle wheel style water flow meter in a waterway that feeds a discharge manifold. The flow meter installation will be such that the unit will have the water flow capabilities listed below, when generating foam solution (as published by FoamPro).

Maximum Accuracy Flow Range
15 -
520
gpm
Maximum Operating Flow Range
5 -
625
gpm
The proportioning system will be capable of the maximum flows listed below at set foam percentages. The unit will not restrict the water flows at any given setting, however exceeding the published flows will result in a lower percentage than is indicated at the control module. .
3 percent setting - Maximum Flow =
533
gpm
.
5 percent setting - Maximum Flow =
320
gpm
1 percent setting - Maximum Flow =
160
gpm
The foam system will be installed in accordance with the manufacturer recommendations.

The system will be equipped with a control module. It will be installed on the pump operator's panel and enable the pump operator to perform the following functions:

Activate the foam system.

Set foam percentage from .
1 percent to
1 percent.

Flash a low concentrate warning light when the foam concentrate tank runs low.

Stop foam pump after two (
2 ) minutes if concentrate tank is still low.

The foam system will have a
12 volt,
1/3
hp electric motor driven positive displacement piston type foam concentrate pump with a rated capacity of .
01 to

1.6 gpm with operating pressures up to
400
psi.

A full flow check valve will be provided in the discharge piping to prevent foam contamination of the fire pump and water tank.

A
5 psi opening pressure check valve will be installed in the concentrate injection line to prevent foam siphoning into the discharge manifold.
0012126
Not Required, CAF Compressor

0802356
Foam Refill, Pump, Foam Pro,
Power-Fill

FOAM REFILL PUMP
A
12 v pump will be permanently mounted in the pump compartment. A male quick disconnect fitting will be provided on the
Left Pump Panel
and a pick-up wand with a
6 ' tube and mating
female fitting will be provided loose.

The control switch for the pump will be located on the pump panel adjacent to the quick disconnect fitting. The pump will be plumbed to the foam tank allowing the user to refill the foam tank from the ground.
0031896
Demonstration, Foam System, Dealer
Provided
0530519
Foam Cell, 30 Gallon, Not Reducing,
PUC

FOAM CELL
The foam cell will be an integral portion of the polypropylene water tank. The cell will have a capacity of
30 gallons of foam with the intended use of
Class A foam
. The brand of foam stored in
this tank will be
Silvex
. The foam cell will not reduce the capacity of the water tank. The foam cell will have a screen in the fill dome and a breather in the lid. 0091036
Drain, 1.00" Foam Tank #1

FOAM TANK DRAIN
The foam tank drain will be a

1.00 " drain valve located inside the pump compartment accessible through a door on the right side pump panel.
0091079
Not Required, Foam Tank #2

0091112
Not Required, Foam Tank #2 Drain

59 972
Bid #:
897
AGENDA ITEM NO. 28.
0746447
Approval Dwg, All Pump Panel(s),
Includes Color And Label Tags
The following drawing(s) will be provided for approval by the customer. The drawing(s) will be made for up
38442
apparatus and/or similar Pierce job number.

PUMP OPERATOR'S PANEL DRAWING
A detailed drawing to scale of the pump operator's panel will be provided for the customer to review. The drawing will include all of the gauges, controls, switching, etc.., located on the pump operator's panel. The customer will be allowed to make changes and/or mark-ups to this approval drawing. The fire apparatus manufacturer will make revisions (If needed) to the drawing per the customer changes and/or mark-ups as long as the changes are physically possible within a specific product line.

The finalized and signed customer approved pump operator's panel drawing will become part of the contract documents.

Due to the way drain(s), bleeder(s), operational/maintenance tag(s) and NFPA required warning tag(s) are placed on pump panel(s), these items will NOT be shown on any pump panel approval drawing(s). These item(s) will be placed on pump panel(s) at the fire apparatus manufacturer discretion.

REMAINING PUMP PANEL(S)
Detailed drawing(s) to scale of the remaining pump panel(s) will be provided for the customer to review. The drawing(s) will include all of the gauges, controls, switching, etc.., located on the pump panel(s). The customer will be allowed to make changes and/or mark-ups to these approval drawing(s). The fire apparatus manufacturer will make revisions (If needed) to the drawing(s) per the customer changes and/or mark-ups as long as the changes are physically possible within a specific product line.

The finalized and signed customer approved pump panel drawing(s) will become part of the contract documents.

Due to the way drain(s), bleeder(s), operational/maintenance tag(s) and NFPA required warning tag(s) are placed on pump panel(s), these items will NOT be shown on any pump panel approval drawing(s). These item(s) will be placed on pump panel(s) at the fire apparatus manufacturer discretion.

COLOR CODED TAGS
A detailed drawing/chart of the colors used on all of the inlet(s) and outlet(s) will be provided for the customer to review. The customer will be allowed to make changes and/or mark-ups to this approval drawing/chart. The fire apparatus manufacturer will make revisions (If needed) to the drawing per the customer changes and/or mark-ups as long as the changes are physically possible within a specific product line.

The finalized and signed customer approved drawing/chart of the colors will become part of the contract documents.

SPECIAL TEXT/VERBIAGE TAGS
A detailed drawing/chart of the text/verbiage used on all of the inlet(s) and outlet(s) will be provided for the customer to review. The customer will be allowed to make changes and/or mark- ups to this approval drawing/chart. The fire apparatus manufacturer will make revisions (If needed) to the drawing per the customer changes and/or mark-ups as long as the changes are physically possible within a specific product line.

The finalized and signed customer approved drawing/chart of the text/verbiage will become part of the contract documents.
0032479
Pump Panel Configuration, Control
Zone

PUMP PANEL CONFIGURATION
The pump panel configuration will be arranged and installed in an organized manner that will provide user-friendly operation.
0831515
Material/Finish, Pump Panels, PUC

PUMP AND GAUGE PANEL
The pump operator's panel and gauge panels will be
brushed stainless steel
finish.

The side panels will be
brushed stainless steel
finish.
0516978
Pump and Plumbing Access, Simple
Tilt Service, PUC

PUMP AND PLUMBING ACCESS
Simple access to the plumbing will be provided through the front of the body area by raising the cab for complete plumbing service and valve maintenance. Access to valves will not require removal of operator panels or pump panels. Access for rebuilding of the pump will not require removal of more than the tank to pump line and a single discharge line. This access will allow for fast, easy valve or pump rebuilding, making for reduced out of service times. Steps will be provided for access to the top of the pump.

Access to the pump will be provided by raising the cab. The pump will be positioned such that all maintenance and overhaul work can be performed above the frame and under the tilted cab. The service and overhaul work on the pump will not require the removal of operator panels or pump panels. Complete pump casing and gear case removal will require no more than removal of the intake and discharge manifolds, driveline, coolers and a single discharge line. The pump case and gear case will be able to be removed by lifting upward without interference from piping and be removable in less than
3 hours.
0618458
Light, Pump Compt, Wln 3SC0CDCR
LED White, PUC

PUMP COMPARTMENT LIGHT
There will be
one (
1 )
Whelen®, Model
3 SC
0 CDCR,

3.00 " white
12 volt DC LED light(s) with
Whelen, Model
3 FLANGEC, flange(s) installed in the plumbing area.

The light(s) will be activated by a toggle switch located in the pump compartment area. 0516983
Gauges, Engine, Included With
Pressure Controller, PUC
Engine monitoring graduated LED indicators will be incorporated with the pressure controller. 0005601
Throttle, Engine, Incl'd w/Press
Controller
60 972
Bid #:
898
AGENDA ITEM NO. 28.
0739224
Indicator Light @ Pump Panel,
Throttle Ready, Incl w/Pressure
Gov/Throttle,Green

THROTTLE READY GREEN INDICATOR LIGHT
There will be a green indicator light integrated with the pressure governor and/or engine throttle installed on the pump operators panel that is activated when the pump is in throttle ready mode. 0549333
Indicators, Engine, Included with
Pressure Controller
0069390
Control, Air Horn At Pmp Pnl, Red
Button

AIR HORN BUTTON
An air horn control button will be provided at the pump operator's control panel. This button will be red in color and properly labeled and put within easy reach of the operator. 0763096
Fittings, Compression IPO PTC, All
Pump Panel Gauges

COMPRESSION FITTINGS
All of the pump panel gauges will have brass compression fittings installed in place of the push to connect fittings.
0895278
SP
Gauges, Flowmeter, Left/Right/Main,
Special Location, PUC

FLOW METER GAUGE LOCATION
The left and right side manifold and main pump flowmeter gauges will be displayed on the pump operator's panel.
0895410
SP
Guards, Half Moon, S/S For
Switches at the Pump Panel with
Locking Pin

GUARD, SWITCH
There will be a stainless steel half moon guard provided over one (
1 )
switches on the pump panel
to prevent accidental activation. A .
25 " pin will be installed to lock the pin in the "OFF" position.

The guard will be provided on the
Main inlet override switch on RS pump panel. (Match Job # 38442
) Arrange so that it is locked in the off position.
switches.
0556650
Switch Panel, Pump Panel, Layout
Info
TBD
.
0830288
Gauges, 6.00" Master, IC, PUC

VACUUM AND PRESSURE GAUGES
The pump vacuum and pressure gauges will be liquid filled and manufactured by Innovative Controls.

The gauges will be a minimum of

6.00 " in diameter and will have
white faces with black markings
,
with a pressure range of

30.00 "
0-600
psi
.

The pump pressure and vacuum gauges will be installed adjacent to each other at the pump operator's control panel.

Test port connections will be provided at the pump operator's panel. One ( 1 ) will be connected to
the intake side of the pump, and the other to the discharge manifold of the pump. They will have

0.25 in. standard pipe thread connections and polished stainless steel plugs. They will be marked with a label.
0038070
Gauge, 2.50" Pressure, Class 1, 30"-
0-400psi

PRESSURE GAUGES
The individual "line" pressure gauges for the discharges will be interlube filled and manufactured by Class
1 ©.

They will be a minimum of

2.50 " in diameter and will have white faces with black lettering.

Gauges will be compound type with a vacuum/pressure range of

30.00 "-
0-400#
.

The individual pressure gauge will be installed as close to the outlet control as practical. 0539612
Gauge, Master Pump Flowmeter,

FRC , PUC

MASTER FLOWMETER
A master pump flowmeter display will be provided the operator's panel. The flowmeter will contain solid state electronics with LED readout of total flow of the pump.

An FRC X-FLC flow conditioner will be installed in the plumbing for better flow readings. 0756688
Gauge, Water Level, Pierce, In
pressure Controller, w/Mini Slave,
PUC, Lt Driver

WATER LEVEL GAUGE
An electric water level gauge will be incorporated in the pressure controller that registers water level by means of nine (
9 ) LEDs. They will be at
1/8
level increments with a tank empty LED. The
LEDs will be a bright type that is readable in sunlight, and have a full 180
-degree of clear viewing.

To further alert the pump operator, the gauge will have a warning flash when the tank volume is less than
25 percent. The gauge will have down chasing LEDs when the tank is almost empty.

The level measurement will be ascertained by sensing the head pressure of the fluid in the tank or cell.

MINI SLAVE UNIT
An electric water level gauge will be provided in the cab that registers water level by means of five (
5 ) LEDs. They will be at
1/4
level increments with a tank empty LED. The LEDs will be a bright type that are readable in sunlight and have a full 180
-degree of clear viewing.

The water level gauge in the cab will be activated when the parking brake is applied
.
61 972
Bid #:
899
AGENDA ITEM NO. 28.
0750438
Water Level Gauge, Wln PSTANK2,
LED 1-Light, 4-Level

WATER LEVEL GAUGE
There will be
two (
2 )
additional water level indicator(s), Whelen®, Model PSTANK 2 , LED module
with
chrome trim
, installed
one (
1 ) each side rearward of crew cab doors
.

This light module(s) will include four (
4 ) colored levels, and function similar to the water level indicator located at the operators panel:

First green module indicates a full water level
Second blue module indicates a water level above
3/4
full
Third amber module indicates a water level above
1/2
full
Last red module indicates a water level above
1/4
full and empty
Above
1/4
this light will be steady burning
At empty this light will be flashing
The flash rate will be determined by the main water level tank sensor.

This module will be activated when the
pump is in gear
.
0517012
Gauge, Foam Level, Pierce, PUC, PP
and Mini in Cab

FOAM LEVEL GAUGE
A Pierce electric foam level gauge will be provided on the operator's panel, that registers foam level by means of nine (
9 ) LEDs. There will also be a mini foam level gauge with five ( 5 ) LEDs in
the cab. They will be at
1/8
level increments with a tank empty LED. The LEDs will be a bright type that is readable in sunlight, and have a full
180
degree of clear viewing. The gauge will
match the water level gauge in the pressure controller.

To further alert the pump operator, will have a warning flash when the tank volume is less than 25 percent, and will have Down Chasing LEDs when the tank is almost empty.

The level measurement will be ascertained by sensing the head pressure of the fluid in the tank or cell. This method provides accuracy with an array of multi-viscosity foams.

The foam level gauge in the cab will be activated by
parking brake is applied
.
0738037
SP
Light, Pump Op & Panel, Side Ctrl,
PUC, AY-LB-12SHW-020 Und
Crosslay, OH Chr Cvr

SIDE CONTROL PUMP OPERATOR'S/PUMP PANEL LIGHTING
Illumination will be provided for controls, switches, essential instructions, gauges, and instruments necessary for the operation of the apparatus and the equipment provided on it. Internal and external lights on the apparatus will be illuminated per the current edition of applicable NFPA standards.

The pump panels will be illuminated by two (
2 ) Amdor Model AY-LB-
12 SHW
020
,
350
lumens

20.00 " weather resistant strip lights with white LED lights, one ( 1 ) on the driver's side and one (
1 )
on the passenger's side. These light strips will be mounted under the speedlay/crosslay compartment.

The pump operator's panel will utilize the same LED strip lighting at the forward doorframe as all other compartment lighting.

There will be a small white LED pump engaged indicator light installed overhead. 0606694
Air Horns, (2) Hadley, 6" Round,
eTone, In Bumper

AIR HORN SYSTEM
Two (
2 ) Hadley®, eTone, chrome air horns will be recessed in the front bumper. The air horn system will be piped to the air brake system wet tank utilizing

0.38 " tubing. A pressure protection
valve will be installed to prevent the loss of air in the brake system. 0606833
Location, Air Horns, Bumper, Each
Side, Inside Frame (Pos #3 & #5)

Air Horn Location
The air horns will be located on each side of the bumper, inside of the frame rails. 0757092
Control, Air Horn, Multi Select

Air Horn Control
The air horn(s) will be activated by the following:
0757084
Control, Air Horn, Horn Ring

Steering wheel horn ring with electric/air horn selector switch 0723391
Control, Air Horn, Chrome Push
Button Sw, RS
Right side chrome push button switch
0688049
Siren, Federal EQ2B-200, 200 Watt

ELECTRONIC SIREN
There will be a Federal, Model EQ
2 B-
200
, electronic siren with noise canceling
microphone provided.

This siren to be active when the battery switch is on and that emergency master switch is on. 0510206
Location, Elect Siren, Recessed
Overhead In Console

Electronic siren head will be
recessed in the driver side inside switch panel
.
0748306
Control, Elec Siren, Multi Select

ELECTRONIC SIREN CONTROL
The electronic siren will be activated by the following:
0748294
Control, Elec Siren, Ft Sw, LS

The left side foot switch.
62 972
Bid #:
900
AGENDA ITEM NO. 28.
0550216
Speaker, (1) Federal, BP200-EF, 200
watt, Stainless Steel

SPEAKER
A Federal, Model BP
200
-EF,
200
watt speaker will be provided. A chrome-plated "EF" flat grille will be installed in front of the speaker.
0601556
Location, Speaker, Frt Bumper,
Recessed, Left Side, Outside Frame,
Inbrd (Pos 6)
The speaker will be recessed in the left side of the front bumper, just outside of the frame rail. 0736164
Sw, Siren Brake, Momentary, LS
Overhead Sw Pnl

A momentary switch will be included in the left side overhead switch panel to activate the siren brake.
0746353
Not Required, Warning Lights
Intensity
0822621
SP
Lightbar, Wln, Freedom IV, 81",
RRRRRRWRROptRRWRRRRRR

FRONT ZONE UPPER WARNING LIGHTS
There will be one (
1 )

81.00 " Whelen Freedom IV LED lightbar mounted on the cab roof.

The lightbar will include the following:

One (
1 ) red flashing LED module in the driver's side rear corner position.

One (
1 ) red flashing LED module in the driver's side end position.

One (
1 ) red flashing LED module in the driver's side front corner position.

One (
1 ) red flashing LED module in the driver's side first front position.

One (
1 ) red flashing LED module in the driver's side second front position.

One (
1 ) red flashing LED module in the driver's side third front position.

One (
1 ) white flashing LED module in the driver's side fourth front position.

One (
1 ) red flashing LED module in the driver's side fifth front position.

One (
1 ) red flashing LED module in the driver's side sixth front position.

One (
1 )
795
LED traffic light controller set to
national standard high priority
in the center positions.

One (
1 ) red flashing LED module in the passenger's side sixth front position.

One (
1 ) red flashing LED module in the passenger's side fifth front position.

One (
1 ) white flashing LED module in the passenger's side fourth front position.

One (
1 ) red flashing LED module in the passenger's side third front position.

One (
1 ) red flashing LED module in the passenger's side second front position.

One (
1 ) red flashing LED module in the passenger's side first front position.

One (
1 ) red flashing LED module in the passenger's side front corner position.

One (
1 ) red flashing LED module in the passenger's side end position.

One (
1 ) red flashing LED module in the passenger's side rear corner position.

There will be
clear lenses included on the lightbar
.

The following switches may be a installed in the cab on the switch panel to control the lightbar:
a switch to control the flashing LED modules.
the traffic light controller
by a cab switch with emergency master control and without emergency master control
.
no momentary switch to activate the traffic light controller .

The white lights and the traffic light controller will be disabled when the parking brake is applied.

The
10 red flashing LED modules in the front positions, and the red flashing LED modules in the ends of the bar, may be load managed when the parking brake is applied. 0833297
SP
Switch, Special Opticom, Labeling,
Mux

SWITCHING & LABELS - OPTICOM
There be
one (
1 )
switch(es) located
Labeled "Opticom Flash", Location
2 - DS Overhead Switch
Panel, top row, far right. Match Job
38442
, that when momentarily depressed, will toggle the
Opticom traffic control emitter on, and depressing the switch(es) a second time will turn the Opticom traffic control emitter off. The switch(es) will be appropriately labeled.

Switching for the Opticom traffic control emitter will be provided so the Opticom traffic control emitter can be turned on without the Emergency Master switch being on.

The parking brake will default the Opticom traffic control emitter to off when applied. 0592278
Light, Front Zone, Wln M6*C & M6*C
Sdy Burn LED, Clear Lens, 4lts Q
Bezel

CAB FACE WARNING LIGHTS
There will be two (
2 ) Whelen®, Model M
6 *C, LED flashing warning lights and two (
2 ) Whelen,
Model M
6 *C, LED steady burning warning lights installed on the cab face, above the headlights, mounted in a common bezel.

The driver outside flashing LED will be
driver's side front outside warning light to be red
The driver inside steady burning LED will be
driver's side front inside warning light to be red
The passenger inside steady burning LED will be
passenger's side front inside warning light to be
red
The passenger outside flashing LED will be
passenger's side front outside warning light to be red
All four (
4 ) lights will include a clear lens.

There will be a switch located in the cab, on the switch panel to control the lights.

The inside lights may be load managed when the parking brake is applied. 0653937
Flasher, Headlight Alternating

HEADLIGHT FLASHER
The high beam headlights will flash alternately between the left and right side.

There will be a switch installed in the cab on the switch panel to control the high beam flash. This switch will be live when the battery switch and the emergency master switches are on.

The flashing will automatically cancel when
the hi-beam headlight switch is activated
or when the
parking brake is set.
63 972
Bid #:
901
AGENDA ITEM NO. 28.
0788934
SP
Lights, Side Zone Lower, Wln M7*
LED, Front Split Color , Clr/Color
Lens, 3pr

SIDE ZONE LOWER LIGHTING
Six (
6 ) Whelen Model M
7 * LED flashing warning lights with bezels will be located in the following positions:

Two (
2 ) lights,
one (
1 ) each side on the bumper extension
.

The
side front lights to be red to the front and white to the rear .

Two (
2 ) lights,
Behind crew cab door both LS and RS. Match Job
38442
.
.

The
side middle lights to be red
.

Two (
2 ) lights,
Located above and to the rear of rear axle, LS and RS. Match Job 38442
.
.

The
side rear lights to be red
.

The two (
2 ) forward lights will include a clear lens.

The four (
4 ) lights to the rear will include a colored lens.

There will be one (
1 ) switch located in the cab on the switch panel to control the lights.

Any white warning lights will be disabled when the parking brake is set. 0745863
Lights, Side, Wln M9** LED, Trm Fet
2nd

SIDE WARNING LIGHTS
There will be
one (
1 )
Whelen®, Model M
9 **,

6.50 " high x

10.37 " wide x

1.37 " deep flashing LED
warning light(s) with
chrome trim
provided,
RS Cab, Above EMS Compartment
.

The
light(s) to include red LEDs
. The
warning light lens color(s) to be clear
.

These lights will be activated
with the side warning switch
.

White LEDs will be deactivated when the parking brake is applied.

Amber, blue, green or red LEDs may be load managed when the parking brake is applied. 0745867
Lights, Side, Wln M9** LED, Trm Fet
1st

SIDE WARNING LIGHTS
There will be
one (
1 )
Whelen®, Model M
9 **,

6.50 " high x

10.37 " wide x

1.37 " deep flashing LED
warning light(s) with
chrome trim
provided,
LS Cab, Above EMS Compartment
.

The
light(s) to include red LEDs
. The
warning light lens color(s) to be clear
.

These lights will be activated
with the side warning switch
.

White LEDs will be deactivated when the parking brake is applied.

Amber, blue, green or red LEDs may be load managed when the parking brake is applied. 0540777
Lights, Rear Zn Lwr, Wln M6*,
Colored Lens

REAR ZONE LOWER LIGHTING
Two (
2 ) Whelen, Model M
6 * LED flashing warning lights with chrome bezels will be located at the rear of the apparatus.

The
driver's side rear light to be red
.

The
passenger's side rear light to be red
.

Both lights will include a lens that is the same color as the LED's.

There will be a switch located in the cab on the switch panel to control the lights. 0898358
Lights, Rear/Side Up Zone, Wln M9**
M9V2** M9V2** M9** 4lts

WARNING LIGHTS (Rear and Side upper zones)
There will be four (
4 ) Whelen LED lights with
chrome trim
provided at the rear of the apparatus.

One (
1 ) Model M
9 **,

6.50 " high x

10.37 " long x

1.37 " deep flashing LED warning light installed on
the driver's side, side of the apparatus as high and close to the rear as practical. The side rear
upper light(s) on the driver's side to be red
.

One (
1 ) Model M
9 V
2 **,

6.50 " high x

10.38 " long x

2.63 " deep flashing LED warning light with
white scene LEDs installed on the driver's side, rear of the apparatus as high and close to the outside as practical. The
rear upper light(s) on the driver's side to be red
.

One (
1 ) Model M
9 V
2 **,

6.50 " high x

10.38 " long x

2.63 " deep flashing LED warning light with
white scene LEDs installed on the passenger's side, rear of the apparatus as high and close to the outside as practical. The
rear upper light(s) on the passenger's side to be red
.

One (
1 ) Model M
9 **,

6.50 " high x

10.37 " long x

1.37 " deep flashing LED warning light installed on
the passenger's side, side of the apparatus as high and close to the rear as practical.The side
rear upper light(s) on the passenger's side to be red
.

The flashing warning lights will include a lens that is the same color as the LED's
. The scene
lights will include a clear lens.

There will be a switch in the cab on the switch panel to control the flashing warning lights.

The scene LEDs will be controlled
by a switch at the driver's side switch panel
.

The scene LEDs may be load managed when the parking brake is applied. 0006551
Not Required, Lights, Rear Upper
Zone Blocking
0590000
No Hose Bed Warn Lts Brkts
Required, Lts On Hatch/Body
Compts,PUC
0791463
Light, Traffic Directing, Wln TANF65,
34" Long LED

TRAFFIC DIRECTING LIGHT
There will be one (
1 ) Whelen® Model TANF
65 ,

34.00 " long x

2.37 " high x

2.37 " deep, amber LED
traffic directing light installed at the rear of the apparatus.

The Whelen Model TACTL
5 control head will be included with this installation.

The control head will be powered when the battery switch is on.

The
auxiliary flash to be activated when the emergency master switch is on .
0637356
SP
Location, TDL, Recessed with S/S
Trim, with Camera
This traffic directing light will be recessed with a stainless steel trim plate at the rear of the apparatus as high as practical. The trim plate will be part of a common bezel around the rear camera.
64 972
Bid #:
902
AGENDA ITEM NO. 28.
0530281
Location, Traf Dir Lt Controller,
Center Console in Sw Pnl

The traffic directing light controller will be located within the switch panel on the center console.

The controller will be within easy reach of the driver. 0781579
Receptacle, 15/20A 120V 3-Pr 3-Wr,
NEMA 5-20R SB Dup, 1st, Interior
Cab
120

VOLT RECEPTACLE
There will be
one (
1 )
,
15/20
amp
120
volt AC three (
3 ) wire straight blade duplex receptacle(s)
with
interior stainless steel wall plate(s)
, installed
Mounted to the back of the DS EMS cabinet
with the receptacle facing inboard towards the engine tunnel. The box should be mounted as low as possible but still allow access for items to be plugged into receptacle without interference. (Match
38442
)
. The NEMA configuration for the receptacle(s) will be
5-20
R.

The receptacle(s) will be powered from the
on board
12 volt DC to
120
volt AC power inverter
.

There will be a label installed near the receptacle(s) that state the following:

Line Voltage
Current Ratting (amps)
Phase
Frequency
0779722
Receptacle, 15/20A 120V 3-Pr 3-Wr,
NEMA 5-20R SB Dup, 1st, Interior
Body
120

VOLT RECEPTACLE
There will be
one (
1 )
,
15/20
amp
120
volt AC three (
3 ) wire straight blade duplex receptacle(s)
with
white receptacle(s) and stainless steel wall plate(s)
, installed
in RS
1 recessed in left wall just
below roll up door. Match Job
38442
.
. The NEMA configuration for the receptacle(s) will be
5-
20 R.

The receptacle(s) will be powered from the
on board
12 volt DC to
120
volt AC power inverter
.

There will be a label installed near the receptacle(s) that state the following:

Line Voltage
Current Ratting (amps)
Phase
Frequency
0778560
Receptacle, 15A 120V 3-Pr 3-Wr TL,
Wtrprfroof
120

VOLT RECEPTACLE
There will be
one (
1 )
,
15 amp
120
volt AC three (
3 ) wire twist lock receptacle(s) with flip up cover
(s) installed
At the rear of the body on the right side rear bulkhead above the taillights. Match Job 38442
.
. The NEMA configuration for the receptacles will be L
5-15
R.

The receptacle(s) will be powered from the
on board
12 volt DC to
120
volt AC power inverter
.

There will be a label installed near the receptacle(s) that state the following:

Line Voltage
Current Ratting (amps)
Phase
Frequency
0519934
Not Required, Brand, Hydraulic Tool
System
0649753
Not Required, PTO Driven Hydraulic
Tool System
0007150
Bag of Nuts and Bolts

LOOSE EQUIPMENT
The following equipment will be furnished with the completed unit:

One (
1 ) bag
of chrome, stainless steel, or cadmium plated screws, nuts, bolts and washers, as used in the construction of the unit.
0766730
Speed Wrench, Electric Valve
Override

SPEED WRECH, ELECTRIC VALVE OVERRIDE
A one piece speed wrench will be provided in loose equipment for manually overriding the electric valve(s) on the truck. The speed wrench will have sockets welded on each end for overriding the valve(s).
65 972
Bid #:
903
AGENDA ITEM NO. 28.
0816508
NFPA Required Loose Equipment,
Pumper, NFPA/ULC 2024, Provided
by Fire Dept

NFPA LOOSE EQUIPMENT
NFPA Required Loose Equipment Provided by Fire Department The following loose equipment as outlined in NFPA
1900
,
2024
edition, table

8.1 and CAN/ULC
S
515:2024
edition, section

5.2 will be provided by the fire department:

One (
1 ) traffic vest for each seating position, each vest to comply with ANSI/ISEA 207
,
Standard
for High Visibility Public Safety Vests
, and have a five-point breakaway feature that includes two (
2 ) at the shoulders, two (
2 ) at the sides, and one (
1 ) at the front.

Five (
5 ) fluorescent orange traffic cones not less than

28.00 " (
711
mm) in height, each equipped
with a

6.00 " (
152
mm) retro-reflective white band no more than

4.00 " (
152
mm) from the top of
the cone, and an additional

4.00 " (
102
mm) retro-reflective white band

2.00 " (
51 mm) below the

6.00 " (
152
mm) band.

Five (
5 ) illuminated warning devices such as highway flares, unless the five ( 5 ) fluorescent
orange traffic cones have illuminating capabilities.

NFPA Loose Equipment That Should be Considered
The following loose equipment as outlined in NFPA
1900
,
2024
edition, appendix table A.

8.4 (a)
and CAN/ULC S
515:2024
edition, section

5.2 should be considered:
800
ft (
60 m) of

2.50 " (
65 mm) or larger fire hose.
400
ft (
120
m) of

1.50 " (
38 mm),

1.75 " (
45 mm), or

2.00 " (
52 mm) fire hose.

One (
1 ) handline nozzle,
200
gpm (
750
L/min) minimum.

Two (
2 ) handline nozzles,
95 gpm (
360
L/min) minimum.

One (
1 ) smooth bore or combination nozzle with shutoff and with

2.50 " (
65 mm) inlet that flows a
minimum of
250
gpm (
950
L/min).

Four (
4 ) SCBA apparatus
Four (
4 ) SCBA spare cylinders
One (
1 ) first aid kit.

Four (
4 ) combination spanner wrenches.

Two (
2 ) hydrant wrenches.

One (
1 ) double female

2.50 " (
65 mm) adapter with national hose (NH) threads.

One (
1 ) double male

2.50 " (
65 mm) adapter with national hose (NH) threads.

One (
1 ) rubber mallet, for use on suction hose connections.

Two (
2 ) salvage covers each a minimum size of
12 ft ×
18 ft (

3.7 m ×

5.5 m).

One (
1 ) automatic external defibrillator (AED).
0816941
Soft Suction Hose, Provided by Fire
Department, NFPA/ULC 2024

SOFT SUCTION HOSE PROVIDED BY FIRE DEPARTMENT
Hose is not on the apparatus as manufactured. The fire department will provide suction or supply hose.
0821565
Strainer, Provided by Fire
Department, Pumper NFPA/ULC
2024 Classification

STRAINER PROVIDED BY FIRE DEPARTMENT
NFPA
1900
,
2024
edition, section

8.3 and CAN/ULC S
515:2024
edition, section

5.2 requires a
suction strainer when suction hose is provided.

The strainer is not on the apparatus as manufactured. The fire department will provide the suction strainer.
0816939
Extinguisher, Dry Chemical, NFPA
2024, Provided by Fire Department

DRY CHEMICAL EXTINGUISHER PROVIDED BY FIRE DEPARTMENT
The extinguisher is not on the apparatus as manufactured. The fire department will provide and mount the extinguisher.
0816937
Extinguisher, 2.5 Gal. Pressurized
Water, NFPA/ULC 2024, Provided by
Fire Dept

WATER EXTINGUISHER PROVIDED BY FIRE DEPARTMENT
The extinguisher is not on the apparatus as manufactured. The fire department will provide and mount the extinguisher.
0820494
Not Required, Axe, Flathead, Fire
Department Omits, NFPA/ULC 2024
0820495
Not Required, Axe, Pickhead, Fire
Department Omits, NFPA/ULC 2024
66 972
Bid #:
904
AGENDA ITEM NO. 28.
0741569
Paint Process / Environmental
Requirements, Appleton

PAINT PROCESS
The exterior custom cab and body painting procedure will consist of a seven ( 7 ) step finishing
process as follows:

Manual Surface Preparation
- All exposed metal surfaces on the custom cab and body will be thoroughly cleaned and prepared for painting. Imperfections on the exterior surfaces will be removed and sanded to a smooth finish. Exterior seams will be sealed before painting. Exterior surfaces that will not be painted include; chrome plating, polished stainless steel, anodized aluminum and bright aluminum treadplate.

Chemical Cleaning and Pretreatment
- All surfaces will be chemically cleaned to remove dirt, oil, grease, and metal oxides to ensure the subsequent coatings bond well. The aluminum surfaces will be properly cleaned and treated using a high pressure, high temperature 4 step Acid Etch
process. The steel and stainless surfaces will be properly cleaned and treated using a high temperature
3 step process specifically designed for steel or stainless. The chemical treatment converts the metal surface to a passive condition to help prevent corrosion.

Surfacer Primer
- The Surfacer Primer will be applied to a chemically treated metal surface to provide a strong corrosion protective basecoat. A minimum thickness of 2 mils of Surfacer Primer
is applied to surfaces that require a Critical aesthetic finish. The Surfacer Primer is a two- component high solids urethane that has excellent sanding properties and an extra smooth finish when sanded.

Finish Sanding
- The Surfacer Primer will be sanded with a fine grit abrasive to achieve an ultra- smooth finish. This sanding process is critical to produce the smooth mirror like finish in the topcoat.

Sealer Primer
- The Sealer Primer is applied prior to the Basecoat in all areas that have not been previously primed with the Surfacer Primer. The Sealer Primer is a two-component high solids urethane that goes on smooth and provides excellent gloss hold out when topcoated.

Base
coat Paint
- Two coats of a high performance, two component high solids polyurethane basecoat will be applied. The Basecoat will be applied to a thickness that will achieve the proper color match. The Basecoat will be used in conjunction with a urethane clear coat to provide protection from the environment.

Clear Coat
- Two (
2 ) coats of Clear Coat will be applied over the Basecoat color. The Clear Coat is a two-component high solids urethane that provides superior gloss and durability to the exterior surfaces. Lap style and roll-up doors will be Clear Coated to match the body. Paint warranty for the roll-up doors will be provided by the roll-up door manufacturer.

After the cab and body are painted, the color will be verified to make sure that it matches the color standard. Electronic color measuring equipment will be used to compare the color sample to the color standard entered into the computer. Color specifications will be used to determine the color match. A Delta E reading will be used to determine a good color match within each family color.

All removable items such as brackets, compartment doors, door hinges, and trim will be removed and painted separately if required, to ensure paint behind all mounted items. Body assemblies that cannot be finish painted after assembly will be finish painted before assembly.

The paint finish quality levels for critical areas of the apparatus (cab front and sides, body sides and doors, and boom lettering panels) are to meet or exceed Cadillac/General Motors GMW
15777
global paint requirements. Orange peel levels are to meet or exceed the #6
A.C.T.
standard in critical areas. The manufacture's written paint standards will be available upon request.

Environmental Impact
Contractor will meet or exceed all current state regulations concerning paint operations. Pollution control will include measures to protect the atmosphere, water and soil. Controls will include the following conditions:

Topcoats and primers will be chrome and lead free.

Metal treatment chemicals will be chrome free. The wastewater generated in the metal treatment process will be treated on-site to remove any other heavy metals.

Particulate emission collection from sanding operations will have a

99.99 percent efficiency factor.

Particulate emissions from painting operations will be collected by a dry filter or water wash process. If the dry filter is used, it will have an efficiency rating of 98 percent. Water wash systems
will be

99.97 percent efficient.

Water from water wash booths will be reused. Solids will be removed on a continual basis to keep the water clean.

Paint wastes are disposed of in an environmentally safe manner.

Empty metal paint containers will be recycled to recover the metal.

Solvents used in clean-up operations will be recycled on-site or sent off-site for distillation and returned for reuse.

Additionally, the finished apparatus will not be manufactured with or contain products that have ozone depleting substances. Contractor will, upon demand, present evidence that the manufacturing facility meets the above conditions and that it is in compliance with his state EPA rules and regulations.
0709846
Paint, Two-Tone Color, Velocity/Impel

CAB TWO-TONE PAINT
The cab will be painted two-tone, with the upper section painted #10
white
and the lower section
painted
#90
red
. There will be
a standard two-tone cab paint break provided
.

There will be
no cab shield provided
.
0709845
Paint, Single Color, Body

BODY PAINT
The body will be
painted to match the lower section of the cab
.
67 972
Bid #:
905
AGENDA ITEM NO. 28.
0646897
Paint Chassis Frame Assy, E-Coat,
Standard

PAINT CHASSIS FRAME ASSEMBLY
The chassis frame assembly will be finished with
a single system black top coat
before the
installation of the cab and body, and before installation of the engine and transmission assembly, air brake lines, electrical wire harnesses, etc.

Components treated with epoxy E-coat protection prior to paint:

Two (
2 ) C-channel frame rails
Components that are included with the chassis frame assembly that will be painted not e-coated (unless otherwise stated in a secondary option) are:

Cross members
Axles
Suspensions
Steering gear
Battery boxes
Bumper extension weldment
Frame extensions
Body mounting angles
Rear Body support substructure (front and rear)
Pump house substructure
Steel fuel tank
Castings
Individual piece parts used in chassis and body assembly The E-coat process will meet the technical properties shown. 0693797
No Paint Required, Aluminum Front
Wheels

0693792
No Paint Required, Aluminum Rear
Wheels

0733739
Paint, Axle Hubs

AXLE HUB PAINT
All axle hubs will be painted
to match lower job color
.
0620095
Paint, Drip Rail, Cab

PAINTED RAIN DRIP
The cab roof rain drip will be painted to match the cab roof paint color. 0581434
Transit Coating, Carwell, Corrosion
Protection, Including Underside

TRANSIT COATING
All non-painted metal surfaces on the exterior of the vehicle will be sprayed with a corrosion protective coating provided by Carwell. The coating can be removed with soap and water.

The coating is made of a linseed oil base and is biodegradable.

The underside non-painted metal surfaces will also be coated with a corrosion protective coating. 0007230
Compartment, Painted, Spatter Gray

COMPARTMENT INTERIOR PAINT
The interior of all compartments will be painted with a gray spatter finish for ease of cleaning and to make it easier to touch up scratches and nicks.
0544087
Reflective Band, 6"

REFLECTIVE BAND
A

6.00 "
white
reflective band will be provided across the front of the vehicle and along the sides of the body.
0510041
Reflective across Cab Face, Imp/Vel

The reflective band provided on the cab face will be below the headlights on the fiberglass. 0593732
Stripe, Chevron, Rear, Diamond
Grade, Pumper, PUC

REAR CHEVRON STRIPING
There will be alternating chevron striping located on the rear-facing vertical surface of the apparatus. The rear surface, excluding the rear roll up door, will be covered.

The colors will be red and
fluorescent yellow
diamond grade.

Each stripe will be

6.00 " in width.

This will meet the requirements of the current edition of NFPA 1901
, which states that
50%
of the
rear surface will be covered with chevron striping.
0011949
"S" Ribbon, Shaded in Reflective
Stripe, Pair
STRIPE, REFLECTIVE, "S" RIBBON
"S" type ribbon(s) will be added to the reflective stripe Match job
38442
.
. Areas adjacent to the
"S" portion of the stripe will be shaded and highlighted with an air brush to give it a ribbon affect.

There will be
one (
1 )
pair on the vehicle.
0065687
Stripe, Reflective, Cab Doors Interior

CAB DOOR REFLECTIVE STRIPE
A

6.00 " x

16.00 "
black
reflective stripe will be provided across the interior of each cab door. The stripe will be located approximately

1.00 " up from the bottom, on the door panel.

This stripe will meet the current edition of applicable NFPA standards. 68 972
Bid #:
906
AGENDA ITEM NO. 28.
0679788
Stripe, Vinyl, Cab Sides, IPO Chrome
Molding

CAB STRIPE
There will be a vinyl stripe provided on both sides of the cab in place of the chrome molding. 0027372
Lettering Specifications, (GOLD
STAR Process)

LETTERING
The lettering will be totally encapsulated between two ( 2 ) layers of clear vinyl.
0686391
Lettering, Gold Leaf, 4.00", (21-40)

LETTERING
Twenty-one (
21 ) to forty (
40 ) genuine gold leaf lettering,

4.00 " high, with
outline and shade
will be
provided.
0067290
Stripe, Gold Leaf, Side of Body, High

BODY STRIPE
There will be a genuine gold leaf stripe provided on each side of the body, located along the top of the side compartmentation.
0686018
Lettering, Reflective, 5.00", Each

LETTERING
There will be reflective lettering,

5.00 " high, with
outline and shade
provided. There will be
six (
6 )
letters
provided.
0686081
Lettering, Reflective, 3.00", (21-40)

LETTERING
Twenty-one (
21 ) to forty (
40 ) reflective lettering,

3.00 " high, with
outline and shade
will be
provided.
0686194
Lettering, Gold Leaf, 12.00", Each

LETTERING
There will be genuine gold leaf lettering,

12.00 " high, with
outline and shade
provided. There will
be
four (
4 ) letters
provided.
0686215
Lettering, Gold Leaf, 8.00", Each

LETTERING
There will be genuine gold leaf lettering,

8.00 " high, with
outline and shade
provided. There will
be
12 letters
provided.
0686236
Lettering, Gold Leaf, 5.00", Each

LETTERING
There will be genuine gold leaf lettering,

5.00 " high, with
outline and shade
provided. There will
be
12 letters
provided.
0683996
Lettering, Vinyl, 20.00", Each

LETTERING
There will be non-reflective vinyl lettering,

20.00 " high, with
no outline or shade
provided. There
will be
three (
3 ) letters
provided.
0012612
Plate, Alum for Reflective Letters

REFLECTIVE PLATE/S FOR LETTERING
There will be
two (
2 )
aluminum plate/s provided for department lettering. The plates will be covered with
ruby red
reflective material and will be mounted
(
1 )
26 "H x
54 "W brushed aluminum
plate & (
1 )

6.5 "H x
15 "W brushed aluminum plate at rear of truck. Match Job 38442
. They will be
Roof plate letter size
20 " & rear plate letter size approx.
6 "
in size.
0017279
Emblem, Corner Scroll, Gold leaf,
Each

CORNER SCROLL
four (
4 )
corner scrolls, comprised of genuine gold leaf, will be provided Upper body corners.

Match Job
38442
.
.
0594393
SP
Emblem, "Waiving American Flag
With Pole, Pair (mirror images)

"AMERICAN FLAG" EMBLEMS
There will be
one (
1 )
pair of color imaged emblems,

10.00 " wide, featuring a "Waiving American
Flag" with pole and
9-11-01
, installed
Located behind the crew cab window on cab sides. Match
Job
38442
. The pair will be mirror images of each other.
0755303
Artwork File, Provided on Custom
USB Drive

ARTWORK ON CUSTOM USB DRIVE
There will be a custom USB drive with department specific artwork files provided to the Fire Department.

Stock artwork, or artwork developed exclusively by Pierce Manufacturing, and proprietary fonts will not be included on the USB drive.
0654570
Emblem, Vinyl, Per Dept. Submittal,
Each
EMBLEM
There will be
two (
2 )
vinyl emblem(s), approximately

10.00 "-

12.00 "
in size, installed
located
between the cab door windows. Ref LP print, Match
38442
.
. the emblem will be modeled after the
department submitted information (art, patch, etc).
69 972
Bid #:
907
AGENDA ITEM NO. 28.
0769753
Emblem, American Flag Painted on
Cab Grille, All Custom Chassis

CAB GRILLE DESIGN
An American flag design will be painted on the cab grille. 0772003
Manual, Fire Apparatus Parts, USB
Flash Drive, Custom

FIRE APPARATUS PARTS MANUAL
There will be
one (
1 )
custom parts manual(s) in USB flash drive format for the complete fire apparatus provided.

The manual(s) will contain the following:

Job number
Part numbers with full descriptions
Table of contents
Parts section sorted in functional groups reflecting a major system, component, or assembly Parts section sorted in alphabetical order
Instructions on how to locate parts
Each manual will be specifically written for the chassis and body model being purchased. It will not be a generic manual for a multitude of different chassis and bodies.

Service Parts Internet Site
The service parts information included in these manuals are also available on the Pierce website.

The website offers additional functions and features not contained in this manual, such as digital photographs and line drawings of select items. The website also features electronic search tools to assist in locating parts quickly.
0772037
Manual, Chassis Service, USB Flash
Drive, Custom

CHASSIS SERVICE MANUALS
There will be
one (
1 )
chassis service manuals on USB flash drives containing parts and service information on major components provided with the completed unit.

The manual will contain the following sections:

Job number
Table of contents
Troubleshooting
Front Axle/Suspension
Brakes
Engine
Tires
Wheels
Cab
Electrical, DC
Air Systems
Plumbing
Appendix
The manual will be specifically written for the chassis model being purchased. It will not be a generic manual for a multitude of different chassis and bodies. 0773381
Manual, Chassis Operation, (1) USB
Flash Drive, Custom

CHASSIS OPERATION MANUAL
The chassis operation manual will be provided on one (
1 ) USB flash drive.
0047891
Manual/s, Maint/Service, Allison EVS
4000 Series Transmission, Add'l

MANUAL/S, (transmission)
There will be
one (
1 )
additional maintenance/service manual(s) for an Allison 4000
series
transmission provided.
0030008
Warranty, Basic, 1 Year, Apparatus,
WA0008
ONE (
1 ) YEAR MATERIAL AND WORKMANSHIP
A Pierce basic apparatus limited warranty certificate, WA 0008
, is included with this proposal.
0611136
Warranty, Chassis, 3 Year,
Velocity/Impel, WA0284

THREE (
3 ) YEAR MATERIAL AND WORKMANSHIP
The Pierce custom chassis limited warranty certificate, WA 0284
, is included with this proposal.
0696698
Warranty, Engine, Cummins, 5 Year,
WA0181

ENGINE WARRANTY
A Cummins
five (
5 ) year
limited engine warranty will be provided. A limited warranty certificate, WA
0181
, is included with this proposal.
0684953
Warranty, Steering Gear, Sheppard
M110, 3 Year WA0201

STEERING GEAR WARRANTY
A Sheppard
three (
3 ) year
limited steering gear warranty will be provided. A copy of the warranty certificate will be submitted with this proposal.
0595767
Warranty, Frame, 50 Year,
Velocity/Impel, WA0038

FIFTY (
50 ) YEAR STRUCTURAL INTEGRITY
The Pierce custom chassis frame and crossmembers limited warranty certificate, WA 0038
, is
included with this proposal.
0595698
Warranty, Axle, 3 Year, TAK-4,
WA0050

FRONT AXLE THREE (
3 ) YEAR MATERIAL AND WORKMANSHIP WARRANTY
The Pierce TAK-
4 suspension limited warranty certificate, WA
0050
, is included with this proposal.
70 972
Bid #:
908
AGENDA ITEM NO. 28.
0733306
Warranty, Single Axle, 5 Year, Meritor,
General Service, WA0384

SINGLE REAR AXLE FIVE (
5 ) YEAR MATERIAL AND WORKMANSHIP WARRANTY
A Meritor
™
Axle
5 year limited warranty will be provided.
0652758
Warranty, ABS Brake System, 3 Year,
Meritor Wabco, WA0232

ABS BRAKE SYSTEM THREE (
3 ) YEAR MATERIAL AND WORKMANSHIP WARRANTY
A Meritor Wabco
™
ABS brake system limited warranty certificate, WA
0232
, is included with this
proposal.
0019914
Warranty, Structure, 10 Year, Custom
Cab, WA0012
TEN (
10 ) YEAR STRUCTURAL INTEGRITY
The Pierce custom cab limited warranty certificate, WA
0012
, is included with this proposal.
0744240
Warranty, Paint, 10 Year, Cab, Pro-
Rate, WA0055
TEN (
10 ) YEAR PRO-RATED PAINT AND CORROSION
A Pierce cab limited pro-rated paint warranty certificate, WA 0055
, is included with this proposal.
0595770
Warranty, Power Step, 2 Year,
WA0031
TWO (
2 ) YEAR MATERIAL AND WORKMANSHIP
The Pierce power step limited warranty certificate, WA
0031
, is included with this proposal.
0524627
Warranty, Electronics, 5 Year, MUX,
WA0014
FIVE (
5 ) YEAR MATERIAL AND WORKMANSHIP
The Pierce Command Zone electronics limited warranty certificate, WA 0014
, is included with this
proposal.
0695416
Warranty, Pierce Camera System,
WA0188

CAMERA SYSTEM WARRANTY
A Pierce fifty four (
54 ) month
warranty will be provided for the camera system
.
0708760
Warranty, Not Applicable, LED Strip
Lights

COMPARTMENT LIGHT WARRANTY
The compartment lights will not offer an extended warranty. 0046369
Warranty, 5-year EVS Transmission,
Standard Custom, WA0187

TRANSMISSION WARRANTY
The transmission will have a
five (
5 ) year/unlimited mileage
warranty covering
100
percent
parts and labor. The warranty will be provided by Allison Transmission.

Note: The transmission cooler is not covered under any extended warranty you may be getting on your Allison Transmission. Please review your Allison Transmission warranty for coverage limitations.
0685945
Warranty, Transmission Cooler,
WA0216

TRANSMISSION COOLER WARRANTY
The transmission cooler will carry a five (
5 ) year parts and labor warranty (exclusive to the
transmission cooler). In addition, a collateral damage warranty will also be in effect for the first three (
3 ) years of the warranty coverage and will not exceed
$10,000
per occurrence. A copy of
the warranty certificate will be included with this proposal. 0688798
Warranty, Water Tank, Lifetime, UPF,
Poly Tank, WA0195

WATER TANK WARRANTY
A UPF poly water tank limited warranty certificate, WA
0195
, is included with this proposal.
0596025
Warranty, Structure, 10 Year, Body,
WA0009
TEN (
10 ) YEAR STRUCTURAL INTEGRITY
The Pierce apparatus body limited warranty certificate, WA 0009
, is included with this proposal.
0693126
Warranty, AMDOR, Roll-up Door, 10
Year/5 Year Painted, WA0185

ROLL UP DOOR MATERIAL AND WORKMANSHIP WARRANTY
An AMDOR roll-up door limited warranty will be provided. The roll-up door will be warranted against manufacturing defects for a period of
ten (
10 ) years
. A
five (
5 ) year
limited warranty will
be provided on painted roll up doors.

The limited warranty certificate, WA
0185
, is included with this proposal.
0889364
Warranty, Pump, Pierce, PUC-NG, 7
Year Parts, 1 Year Labor, WA0390

SEVEN (
7 ) YEAR PARTS, ONE (
1 ) YEAR LABOR
The pump and its components will be provided with a seven ( 7 ) year parts and one (
1 ) year labor
limited warranty. The manufacturer's warranty will provide that the pump and its components will be free from failures caused by defects in material and workmanship that would arise under normal use and service.

A copy of the warranty certificate will be submitted with the bid package. 0648675
Warranty, 10 Year S/S Pumbing,
WA0035
TEN (
10 ) YEAR PUMP PLUMBING WARRANTY
The Pierce apparatus plumbing limited warranty certificate, WA 0035
, is included with this
proposal.
0641372
Warranty, Foam System, Not
Available
71 972
Bid #:
909
AGENDA ITEM NO. 28.
0595820
Warranty, Paint, 10 Year, Body, Pro-
Rate, WA0057
TEN (
10 ) YEAR PRO-RATED PAINT AND CORROSION
A Pierce body limited pro-rated paint warranty certificate, WA 0057
, is included with this proposal.
0595421
Warranty, Goldstar, 3 Year,
Apparatus, WA0018

THREE (
3 ) YEAR MATERIAL AND WORKMANSHIP
The Pierce Goldstar gold leaf lamination limited warranty limited warranty certificate, WA 0018
, is
included with this proposal.
0819254
Certification, Vehicle Stability,
CD0196

VEHICLE STABILITY CERTIFICATION
The fire apparatus manufacturer will provide a certification stating the apparatus complies with NFPA
1900
, current edition, section

7.14 , Vehicle Stability. The certification is included with this proposal.
0808577
Certification, Engine Installation,
Velocity, Cummins X15, 2027

ENGINE INSTALLATION CERTIFICATION
The fire apparatus manufacturer will provide a certification, along with a letter from the engine manufacturer stating they approve of the engine installation in the bidder's chassis. The certification will be provided at the time of delivery. 0686786
Certification, Power Steering,
CD0098

POWER STEERING CERTIFICATION
The fire apparatus manufacturer will provide a certification stating the power steering system as installed meets the requirements of the component supplier. The certification is included with this proposal.
0892701
Certification, Cab Integrity,
Impel/Velocity FR, CD0190

CAB INTEGRITY CERTIFICATION
The fire apparatus manufacturer will provide a cab crash test certification with this proposal. The certification will state that a specimen representing the substantial structural configuration of the cab has been tested and certified by an independent third party test facility. Testing events will be documented with photographs, real-time and high-speed video, vehicle accelerometers, cart accelerometers, and a laser speed trap. The fire apparatus manufacturer will provide a state licensed professional engineer to witness and certify all testing events. Testing will meet or exceed the requirements below:

SAE J
2422
Cab Roof Strength Evaluation - Quasi-Static Loading Heavy Trucks.

European Occupant Protection Standard ECE Regulation No. 29 .

SAE J
2420
COE Frontal Strength Evaluation - Dynamic Loading Heavy Trucks.

Side Impact
The cab will be subjected to dynamic preload where a
14,320
-lb moving barrier is slammed into
the side of the cab at

5.50 mph, striking with an impact of
13,000
ft-lb of force. This test is part of
the SAE J
2422
test procedure and more closely represents the forces a cab will see in a rollover incident.

Roof Crush
The same cab will be subjected to a roof crush force of 22,050
lb. This value meets the ECE
29 criteria and is equivalent to the front axle rating up to a maximum of ten ( 10 ) metric tons.

Additional Roof Crush
The same cab will be subjected to a roof crush force of 100,000
lb. (Four and a half times the
load criteria of ECE
29 )
Frontal Impact
The same cab will withstand a frontal impact of
32,600
ft-lb of force using a moving barrier in
accordance with SAE J
2420
.

Additional Frontal Impact
The same cab will withstand a frontal impact of
65,200
ft-lb of force using a moving barrier. (Twice
the force required by SAE J
2420
)
The same cab will withstand all tests without any measurable intrusion into the survival space of the occupant area.
0548950
Certification, Cab Door Durability,
Velocity/Impel, CD0001

CAB DOOR DURABILITY CERTIFICATION
Robust cab doors help protect occupants. Cab doors will survive a 200,000
-cycle door slam test
where the slamming force exceeds
20 G's of deceleration. The bidder will certify that the sample doors similar to those provided on the apparatus have been tested and have met these criteria without structural damage, latch malfunction, or significant component wear. 0548967
Certification, Windshield Wiper
Durability, Impel/Velocity, CD0005

WINDSHIELD WIPER DURABILITY CERTIFICATION
Visibility during inclement weather is essential to safe apparatus performance. Windshield wipers will survive a
3 million cycle durability test in accordance with section

6.2 of SAE J
198

Windshield
Wiper Systems - Trucks, Buses and Multipurpose Vehicles.

The bidder will certify that the wiper
system design has been tested and that the wiper system has met these criteria. 0667411
Certification, Electric Window
Durability, Velocity/Impel FR, CD0004

ELECTRIC WINDOW DURABILITY CERTIFICATION
Cab window roll-up systems can cause maintenance problems if not designed for long service life. The window regulator design will complete
30,000
complete up-down cycles and still function
normally when finished. The bidder will certify that sample doors and windows similar to those provided on the apparatus have been tested and have met these criteria without malfunction or significant component wear.
72 972
Bid #:
910
AGENDA ITEM NO. 28.
0549273
Certification, Seat Belt Anchors and
Mounting, Imp/Vel/Vel SLT, CD0018

SEAT BELT ANCHOR STRENGTH
Seat belt attachment strength is regulated by Federal Motor Vehicle Safety Standards and should be validated through testing. Each seat belt anchor design will withstand 3000
lb of pull on both
the lap and shoulder belt in accordance with FMVSS
571.210
Seat Belt Assembly Anchorages.

The bidder will certify that each anchor design was pull tested to the required force and met the appropriate criteria.

SEAT MOUNTING STRENGTH
Seat attachment strength is regulated by Federal Motor Vehicle Safety Standards and should be validated through testing. Each seat mounting design will be tested to withstand 20 G's of force in
accordance with FMVSS
571.207
Seating Systems. The bidder will certify that each seat mount and cab structure design was pull tested to the required force and met the appropriate criteria. 0735950
Certification, Cab HVAC System Perf,
Vel/Imp FR,
CD0166/CD0168/CD0176/CD0177

PERFORMANCE CERTIFICATIONS
Cab Air Conditioning
Good cab air conditioning temperature and air flow performance keeps occupants comfortable, reduces humidity, and provides a climate for recuperation while at the scene. The cab air conditioning system will cool the cab from a heat-soaked condition at 100
degrees Fahrenheit to
an average of
78 degrees Fahrenheit in
30 minutes. The bidder will certify that a substantially similar cab has been tested and has met these criteria.

Cab Defroster
Visibility during inclement weather is essential to safe apparatus performance. The defroster system will clear the required windshield zones in accordance with SAE J 381
Windshield
Defrosting Systems Test Procedure And Performance Requirements - Trucks, Buses, And Multipurpose Vehicles.

The bidder will certify that the defrost system design has been tested in a cold chamber and passes the SAE J
381
criteria.

Cab Auxiliary Heater
Good cab heat performance and regulation provides a more effective working environment for personnel, whether in-transit, or at a scene. An auxiliary cab heater will warm the cab 77 degrees
Fahrenheit from a cold-soak, within
30 minutes when tested using the coolant supply methods found in SAE J
381
. The bidder will certify, at time of delivery, that a substantially similar cab has been tested and has met these criteria.
0545073
Amp Draw Report, NFPA Current
Edition

AMP DRAW REPORT
The bidder will provide, at the time of bid and delivery, an itemized print out of the expected amp draw of the entire vehicle's electrical system.

The manufacturer of the apparatus will provide the following:

Documentation of the electrical system performance tests.

A written load analysis, which will include the following:

The nameplate rating of the alternator.

The alternator rating under the conditions specified per:

Current edition of applicable NFPA standards.

The minimum continuous load of each component that is specified per:

Current edition of applicable NFPA standards.

Additional loads that, when added to the minimum continuous load, determine the total connected load.

Each individual intermittent load.

All of the above listed items will be provided by the bidder per the current edition of applicable NFPA standards.
0002758
Amp Draw, NFPA/ULC Radio
Allowance
0799248
Appleton/Florida BTO

0000048
PUMPER/TANKER, 3rd Gen

0000012

PIERCE CHASSIS
0004713

ENGINE, OTHER
0046396
EVS 4000 Series TRANSMISSION
0520324

PIERCE PUMP, PUC

0020009

POLY TANK

0028048

FOAM SYSTEM
73 972
Bid #:
911
AGENDA ITEM NO. 28.
0020006

SIDE CONTROL
0020007

AKRON VALVES

0020014

FRONT SUCTION

0020015

ABS SYSTEM

0658751

PUMPER BASE

74 972
Bid #:
912
AGENDA ITEM NO. 28.

Option
Description
Type*
Minimum
Load
Intermittent
Load
Total
Connected
0001244
High Idle w/Electronic Engine, Custom

0.00 1.20

0.00 0002526
Light, Engine Compt, All Custom Chassis

0.00 1.60

0.00 0069390
Control, Air Horn At Pmp Pnl, Red Button

0.00 0.16

0.00 0072153
Primer, Trident, Air Prime, Air Operated

0.00 0.00

0.00 0085910
Lights, Backup Included in Signal Cluster

0.00 4.20

0.00 0098841
Batteries, (6) Deka Grp 31, 1000 CCA each, Threaded Stud

0.00 3.00

0.00 0122466
Cab Lift, Elec/Hyd, w/Manual Override, Imp/Vel

0.00 180.00

0.00 0517012
Gauge, Foam Level, Pierce, PUC, PP and Mini in Cab

0.00 0.00

1.23 0543751
Light, Do Not Move Apparatus

0.00 0.80

0.00 0549333
Indicators, Engine, Included with Pressure Controller

0.00 0.35

0.00 0589905
Alarm, Back-up Warning, PRECO 1040

0.00 0.50

0.00 0596662
Intercom, Sigtronics US-67S, 6-Pos, 3-Radio, D,O,3C,P

0.00 0.00

0.50 0617886
Foam Sys, FoamPro 1600, Single Agent, PUC, Multi Select Feature

0.00 36.00

0.00 0618458
Light, Pump Compt, Wln 3SC0CDCR LED White, PUC

0.00 0.36

0.00 0628472
Light, Map, Overhead, Peterson M371S LED, Rectangular
w/Switch 2lts

0.00 0.24

0.00 0653559
Reel, Booster, Two (2) - Over Pump, Alum, PUC

0.00 72.00

0.00 0667902
Controls, Electric Windows, All Cab Doors, Impel/Velocity FR

0.00 26.00

0.00 0687994
Engine Brake, Jacobs Compression Brake, Cummins Engine

0.00 0.42

0.00 0728395
177" Hatch, (1) Lift-up, 21" Wide, Both Sides, Shortened for Cargo Area, PUC

0.00 3.25

3.25 0745863
Lights, Side, Wln M9** LED, Trm Fet 2nd

0.00 1.80

1.20 0745867
Lights, Side, Wln M9** LED, Trm Fet 1st

0.00 1.80

1.20 0763096
Fittings, Compression IPO PTC, All Pump Panel Gauges

0.00 0.16

0.00 0767497
Control, Front Inlet, Akron 9333 Elec Controller, w/Override, PUC, Disconnect Sw

0.00 2.50

0.00 0817058
Camera, Pierce, LS Mux, R Camera, SD, CL714

0.00 1.20

0.00 0819994
Radio, Jensen, AM/FM/WB, Bluetooth

0.00 0.00

2.00 0820509
ESC/ABS/ATC Wabco Brake System, Single Rear Axle, NFPA 1900/ULC

0.00 6.00

0.00 0820904
Wiring, Spare, 15 A 12V DC 1st NFPA1900/ULC

0.00 0.00

30.00 0820921
Wiring, Spare, 4.8 A 12V DC, USB Term, Blue Sea 1045, Batt Dir, 1st NFPA1900/ULC

0.00 0.00

4.80 0821195
Wiring, Spare, 20 A 12V DC 2nd NFPA1900/ULC

0.00 0.00

20.00 0821263
Wiring, Spare, 20 A 12V DC, 12 Ckt FB, Blue Sea 5026 Batt Dir 1st NFPA1900/ULC

0.00 0.00

20.00 0821266
Wiring, Spare, 20 A 12V DC, 12 Ckt FB, Blue Sea 5026 Batt Dir 2nd NFPA1900/ULC

0.00 0.00

20.00 0821325
Wiring, Spare, 10 A 12V DC 1st NFPA1900/ULC

0.00 0.00

10.00 0821329
Wiring, Spare, 10 A 12V DC Batt Dir 1st NFPA1900/ULC

0.00 0.00

10.00 0826636
Wiring, Spare, (1) 15A 12V DC, Multi Loc, Cab, B+, 1st, NFPA1900/ULC

0.00 0.00

15.00 0889662
Lights, Wln, S16*M* 16.37" 12VDC, Brkt Fet 2nd

0.00 0.00

3.66 0889664
Lights, Wln, S16*M* 16.37" 12VDC, Brkt Fet 1st

0.00 0.00

3.66 0893371
Lights, Wln, M9LZC Gradient, 12 VDC, 2nd

0.00 0.00

12.00 0893374
Lights, Wln, M9LZC Gradient, 12 VDC, 1st

0.00 0.00

12.00 0012188
Mirrors, Velvac, 2025, Heated/Remote, w/Heated Convex
Load Managed

0.00 0.00

8.00 0741239
HVAC, Heavy-Duty, Impel/Velocity FR, CARE
Load Managed

0.00 0.00
136.00
0819181
Inverter/Battery Charger, Xantrex Freedom 817-2080, GFCI, Non- NFPA 2024 80 Amp
Load Managed

0.00 0.00
195.31
0898549
Cab Air Filtration, TFT CrewProtect 100, 12v DC, Loc, CARE Load Managed

0.00 0.00

1.50 0002758
Amp Draw, NFPA/ULC Radio Allowance
NFPA

5.00 0.00

0.00 0092582
Load Manager/Sequencer, MUX
NFPA

0.56 0.56

0.00 0516983
Gauges, Engine, Included With Pressure Controller, PUC
NFPA

0.30 0.00

0.00 0517025
Lights, Tail, Wrap-around, Stop/Tail, Turn & Backup LED, Tri- Cluster
NFPA

2.60 7.80

0.00 0518345
LS 177" Rollup, (1) 50" Forward, (1) 52" Rear, FH/FD Front & Rear, PUC
NFPA

6.00 0.00

6.00 * UDMC = User Defined Mission Critical, LM = User Defined Load Managed, S = Electrical Amperage Supply 1 Electrical Analysis
6/16/2025
Bid #:
972
Clovis Fire Department, Velocity PUC. Duplicate to 38442 Sales Rep:

Organization:

Young, Dewayne
Golden State Fire Apparatus, Inc
Desc:

Job #:

Customer:

CLOVIS FIRE DEPARTMENT
Option:

Pierce Command Zone, Advanced Electronics & Control
System, Vel WiFi CZT
Type:

Multiplexed
913
AGENDA ITEM NO. 28.

Option
Description
Type*
Minimum
Load
Intermittent
Load
Total
Connected
0518346
RS 177" Rollup, (1) 50" Forward, (1) 52" Rear, FH/FD Front & Rear, PUC
NFPA

6.00 0.00

6.00 0540777
Lights, Rear Zn Lwr, Wln M6*, Colored Lens
NFPA

1.80 2.70

0.00 0555915
Wiper Control, 2-Speed with Intermittent, MUX, Impel/Velocity NFPA

2.10 8.40

0.00 0557322
Lights, Step, P25 at Rear Tailboard, PUC, 4lts Perm Lts NFPA

0.50 0.00

0.00 0568369
Cab Instruments, Ivory Gauges, Chrome Bezels, Impel/Velocity 2010
NFPA

1.26 0.00

0.00 0587034
Air Dryer, Bendix, AD-IP w/Heat, 2010
NFPA

4.70 0.00

0.00 0592278
Light, Front Zone, Wln M6*C & M6*C Sdy Burn LED, Clear Lens, 4lts Q Bezel
NFPA

2.70 5.40

0.90 0599445
Compt, Rear, Rollup, 33.50" FF, w/Tailboard, PUC/HDRP
NFPA

0.90 0.00

0.90 0620054
Light, Directional/Marker, Intermediate, Weldon 9186-8580-29 LED 2lts
NFPA

0.10 0.90

0.00 0644702
Compt, Storage, (2) Rear Facing, Overhead, 22 W x 10 H x 20 D, Imp/Vel FR
NFPA

0.22 0.22

0.00 0645873
Lights, Hose Bed, Sides, Dual LED Light Strips, Amdor XX9951 4lts
NFPA

3.40 0.00

0.00 0647647
Lights, Dome, FRP Dual LED 4 Lts
NFPA

0.80 0.80

0.00 0648425
Light, Directional, Wln 600 Cmb, Cab Crn, Wrp Bzl Out HD Lts, Imp/Vel/AXT/Qtm
NFPA

0.70 0.70

0.00 0653937
Flasher, Headlight Alternating
NFPA

0.08 0.00

0.00 0659814
Lights, Hatch Compt, Amdor AY-9220 LED Strip Light, 177", Both Sides
NFPA

1.77 1.77

0.00 0662965
DEF Tank, 4.5 Gallon, DS Fill, Rear of Axle, Common Air Bottle Door
NFPA

0.60 11.40

0.00 0668310
Cab, Velocity FR, 7010 Raised Roof, PUC
NFPA

6.80 10.20

0.00 0688049
Siren, Federal EQ2B-200, 200 Watt
NFPA

2.01 18.13

0.00 0709438
Lights, Walk Surf, FRP Flood, LED
NFPA

2.00 0.00

0.00 0724463
Controller, Pressure, Pierce LCD , PUC
NFPA

1.70 0.00

0.00 0738037
Light, Pump Op & Panel, Side Ctrl, PUC, AY-LB-12SHW-020 Und Crosslay, OH Chr Cvr
NFPA

3.00 0.00

0.00 0739224
Indicator Light @ Pump Panel, Throttle Ready, Incl w/Pressure Gov/Throttle,Green
NFPA

0.10 0.00

0.00 0747660
Lights, Crosslay Compt, Forward LED, 2Lts
NFPA

1.20 0.00

0.00 0749399
Light, Visor Mt, Wln S72M**, 72" Cnt Feature
NFPA

0.32 0.00

18.68 0750438
Water Level Gauge, Wln PSTANK2, LED 1-Light, 4-Level
NFPA

1.60 0.00

0.00 0756688
Gauge, Water Level, Pierce, In pressure Controller, w/Mini Slave, PUC, Lt Driver
NFPA

1.23 0.00

0.00 0768459
Lights, Perimeter Cab, Amdor AY-LB-12HW012 LED 4Dr, Pwr Step, Vel/Imp
NFPA

0.72 0.00

0.00 0769559
Lights, Perimeter Pump House, Amdor AY-LB-12HW012 LED 2lts NFPA

0.36 0.00

0.00 0769560
Lights, Perimeter Body, Amdor AY-LB-12HW012 LED 2lts, Rear Step
NFPA

0.36 0.00

0.00 0783153
Headlights, Rect LED, JW Spkr Evo 2, AXT/Enf/Imp/Sab/Vel NFPA

4.20 4.20

0.00 0788934
Lights, Side Zone Lower, Wln M7* LED, Front Split Color , Clr/Color Lens, 3pr
NFPA

5.40 8.10

0.00 0791463
Light, Traffic Directing, Wln TANF65, 34" Long LED
NFPA

2.00 4.00

0.00 0796870
Lights, Clearance/Marker/ID, Rear, FRP LED Bar & Truck-Lite 33050R LED 4Lts, PUC
NFPA

0.25 0.25

0.50 0805711
Cabinet, Rear Facing, LS, 24 W x 32 H x 30.5 D, Radius, Ext Acc, Imp/Vel
NFPA

0.48 0.48

0.00 0809508
Lights, Cab & Crw Cab Acs Stps, P25, LED, 4Lts, 4-Door Cab, Auto Steps
NFPA

0.14 0.14

0.00 0812268
Engine, Cummins X15, 525 hp, 1850 lb-ft, W/OBD, EPA 2027, Velocity, PUC-NG
NFPA

6.00 0.00

0.00 0812671
Valve, w/Relief, LS Main Inlet, 6", Elec, Akron 9333 Cont, w/O- ride,PUC
NFPA

0.28 17.72

0.00 0814201
Vehicle Information Center, 7" Color Display, Touchscreen, MUX, CL714
NFPA

1.20 0.00

0.00 0822621
Lightbar, Wln, Freedom IV, 81", RRRRRRWRROptRRWRRRRRR
NFPA

7.85 0.23

18.00 0833781
Cabinet, Rear Facing, RS, 21.5 W x 32 H x 30.5 D, Radius, Ext Acc, Imp/Vel
NFPA

0.32 0.32

0.00 0887546
Trans, Allison 6th Gen, 4000 EVS P, w/Prognostics,
Imp/Vel/SFR/Enf
NFPA

2.00 2.00

0.00 0889577
Bracket, License Plate & Light, P25 LED, Stainless Brkt NFPA

0.07 0.00

0.00 0898358
Lights, Rear/Side Up Zone, Wln M9** M9V2** M9V2** M9** 4lts NFPA

4.32 6.48

4.80 0647728
Alternator, 430 amp, Delco Remy 55SI
S

0.00 0.00

0.00 Load Totals:

98.00 456.44
567.09
* UDMC = User Defined Mission Critical, LM = User Defined Load Managed, S = Electrical Amperage Supply 2 Electrical Analysis
6/16/2025
Bid #:
972
Clovis Fire Department, Velocity PUC. Duplicate to 38442 Sales Rep:

Organization:

Young, Dewayne
Golden State Fire Apparatus, Inc
Desc:

Job #:

Customer:

CLOVIS FIRE DEPARTMENT
Option:

Pierce Command Zone, Advanced Electronics & Control
System, Vel WiFi CZT
Type:

Multiplexed
914
AGENDA ITEM NO. 28.

Minimum Continuous Load
Supply:
253.00
Demand:

98.00 Variance:
155.00
Total Connected Load
Supply:
369.00
Demand:
324.28
Variance:

44.72 Note: Minimum Continous Load is in "Blocking Right of Way" mode.(Reference current edition of NFPA 1901) Note: Intermittent Load items are not factored in on any alternator load comparisons. These items are included on the report for reference only and should be looked at as amp draw exclusion items. (Reference current edition of NFPA 1901) Note: Total Connected Load "Demand" represents Total Connected Load minus any Load Managed items 253.00
369.00
Alternator Output at Idle:

Alternator Output at Governed Speed:
* UDMC = User Defined Mission Critical, LM = User Defined Load Managed, S = Electrical Amperage Supply 3 Electrical Analysis
6/16/2025
Bid #:
972
Clovis Fire Department, Velocity PUC. Duplicate to 38442 Sales Rep:

Organization:

Young, Dewayne
Golden State Fire Apparatus, Inc
Desc:

Job #:

Customer:

CLOVIS FIRE DEPARTMENT
Option:

Pierce Command Zone, Advanced Electronics & Control
System, Vel WiFi CZT
Type:

Multiplexed
915
AGENDA ITEM NO. 28.

Turning Performance Analysis
Bid Number:
972
Chassis:

Velocity Chassis, PUC-NG (Big Block)
Department:

CLOVIS FIRE DEPARTMENT
Body:

Pumper, PUC, Aluminum
Parameters:
*Inside Cramp Angle:
45°
Axle Track:

82.92 in.

Wheel Offset:

4.68 in.

Tread Width:

16.3 in.

Chassis Overhang:
78 in.

Additional Bumper Depth:
22 in.

Front Overhang:
100 in.

Wheelbase:
180.5 in.

Calculated Turning Radii:

Inside Turn:
13 ft. 0 in.

Curb to curb:
27 ft. 8 in.

Wall to wall:
32 ft. 10 in.

Notes:
*Actual Inside cramp angle may be less than shown.

Curb to Curb turning radius calculated for 9.00 inch curb. 06/16/2025
Category
Option
Description
Bumpers
0123626
Bumper, 22" Extended, Imp/Vel
Tires, Front
0899288
Tires, Front, Goodyear, Armor MAX MSA, 425/65R22.50, 20 ply, Fire Service Speed
Axle, Front, Custom
0508849
Axle, Front, Oshkosh TAK-4, Non Drive, 22,800 lb, Imp/Vel Wheels, Front
0019611
Wheels, Front, Alcoa, 22.50" x 12.25", Aluminum, Hub Pilot 916
AGENDA ITEM NO. 28.

Definitions:

Inside CrampAngle
Maximum turning angle of the front inside fire.

Axle Track
King-pin to King-pin distance of front axle.

Wheel Offset
Offset from the center line of the wheel to the King-pin.

Tread Width
Width of the tire tread.

Chassis Overhang
Distance of the center line of the front axle to the front edge of the cab. This does not include the bumper depth.

Additional Bumper Wheel
Depth that the bumper assembly adds to the front overhang.

Wheelbase
Distance between the center lines of the vehicles front and rear axles.

Inside Turning Radius
Radius of the smallest circle around which the vehicle can turn.

Curb to Curb Turning Radius
Radius of the smallest circle around which the vehicle's tires can turn. This measures assumes a curb height of 9 inches.

Wall to Wall Turning Radius
Radius of the smallest circle around which the vehicle's tires can turn. This measures takes into account any front overhang due to chassis , bumper extensions and or aerial devices. 917
AGENDA ITEM NO. 28.

JROGHQVWDWHĆUHFRP

PRODUCT

WARRANTIES
Exhibit “C”
4 918
AGENDA ITEM NO. 28.

Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 2/8/2010 WA0008

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.

This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

No specific exclusions apply
Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4
Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

Fire and Rescue Apparatus
Coverage:

One (1) Year Material and Workmanship
Basic Apparatus
Twelve (12) months.Warranty Period
Ends After:

The date the apparatus is placed in service, or 60 days from the original buyer invoice date, whichever comes first.Warranty Begins:

Portions of the apparatus manufactured by Pierce shall be free from defects in material and workmanship
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.

Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.

3. BUYER'S EXCLUSIVE REMEDY.
919
AGENDA ITEM NO. 28.

Fire and Rescue Apparatus
Coverage:

Three (3) Year Material and Workmanship
Velocity and Impel Custom Chassis
Limited Warranty Limited Warranty Limited Warranty Limited Warranty Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

Portions of the apparatus manufactured by Pierce shall be free from defects in material and workmanship

1. LIMITED WARRANTY
(b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; The date the apparatus is placed in service, or 60 days from the original buyer invoice date, whichever comes first. Warranty Begins:

This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This limited warranty applies, where applicable, to Goldstar lamination, defroster heater coil and motor blower assembly (excluding the FET PWM module), heater, air conditioning condenser coil and fan/motor assembly, air conditioning evaporator coil and motor blower assembly (excluding the drain pan pump and thermostat), under seat heaters coil and motor blower assembly (excluding the FET PWM module),
HVAC electronic switches, HVAC hoses and hard lines,
heater water valve, Pierce PS6 seat frames and hardware, Pierce One-Eleven mirrors, Pierce hands-free scba holder, cracking or color loss of roto-molded components, Meritor rear axle, Wabco ABS system, cab door handles, Standen
spring suspension components, and the gauge instrument
cluster.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGE S.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE
POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.

Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.

3. BUYER'S EXCLUSIVE REMEDY.
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce.

Three (3) Years, or
30,000 Miles, or
5000 Engine Hours
Warranty Period
Ends After:

Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle.
7/2/2015 WA0284
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES

ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty. 920
AGENDA ITEM NO. 28.

Cummins Warranty
Worldwide
Fire Apparatus/Crash Trucks
921
AGENDA ITEM NO. 28.

Coverage
Products Warranted
This Warranty applies to new diesel Engines sold by
Cummins and delivered to the first user on or after
April 1, 2007, that are used in fire apparatus truck and crash truck* applications Worldwide.

Base Engine Warranty
The Base Engine Warranty covers any failures of the
Engine which result, under normal use and service,
from a defect in material or factory workmanship
(Warrantable Failure). This Coverage begins with the
sale of the Engine by Cummins and ends five years or
100,000 miles (160,935 kilometers), whichever occurs
first, after the date of delivery of the Engine to the first user .

Engine aftertreatment components included in the
Cummins Critical Parts List (CPL) and marked with a
Cummins part number are covered under Base Engine
Warranty.

Additional Coverage is outlined in the Emission
Warranty section.

These Warranties are made to all Owners in the
chain of distribution and Coverage continues to all
subsequent Owners until the end of the periods of
Coverage.

Cummins
Responsibilities
Cummins will pay for all parts and labor needed to
repair the damage to the Engine resulting from a
Warrantable Failure.

Cummins will pay for the lubricating oil, antifreeze,
filter elements, belts, hoses and other maintenance
items that are not reusable due to the Warrantable
Failure.

Cummins will pay for reasonable labor costs for
Engine removal and reinstallation when necessary to
repair a Warrantable Failure.

Cummins will pay reasonable costs for towing a
vehicle disabled by a Warrantable Failure to the
nearest authorized repair location. In lieu of the towing expense, Cummins will pay reasonable costs for
mechanics to travel to and from the location of the
vehicle, including meals, mileage and lodging when
the repair is performed at the site of the failure.

Owner
Responsibilities
Owner is responsible for the operation and
maintenance of the Engine as specified in Cummins
Operation and Maintenance Manuals. Owner is also
responsible for providing proof that all recommended
maintenance has been performed.

Before the expiration of the applicable Warranty,
Owner must notify a Cummins distributor ,authorized
dealer or other repair location approved by Cummins
of any Warrantable Failure and make the Engine
available for repair by such facility. Except for Engines disabled by a Warrantable Failure, Owner must also
deliver the Engine to the repair facility.

Service locations are listed on the Cummins Worldwide
Service Locator at cummins.com.

Owner is responsible for the cost of lubricating oil,
antifreeze, filter elements and other maintenance items provided during Warranty repairs unless such items
are not reusable due to the Warrantable Failure.

Owner is responsible for communication expenses,
meals, lodging and similar costs incurred as a result of a Warrantable Failure.

Owner is responsible for non-Engine repairs and for
‘‘downtime’’expenses, cargo damage, fines, all
applicable taxes, all business costs and other losses
resulting from a Warrantable Failure.

Owner is responsible for a $100 (U.S. Dollars)
deductible per each service visit under this plan in the 3rd, 4th and 5th years of Base Engine Warranty. The
deductible will not be charged during the first 2 years of the Base Engine Warranty.

Limitations
Cummins is not responsible for failures or damage
resulting from what Cummins determines to be abuse
or neglect, including, but not limited to: operation
without adequate coolants or lubricants; overfueling;
overspeeding; lack of maintenance of lubricating,
cooling or intake systems; improper storage, starting,
warm-up, run-in or shutdown practices; unauthorized
modifications of the Engine.

Any unauthorized modifications to the aftertreatment
could negatively effect emissions certification and void Warranty.

Cummins is also not responsible for failures caused by
incorrect oil, fuel or diesel exhaust fluid or by water , dirt or other contaminants in the fuel, oil or diesel
922
AGENDA ITEM NO. 28.
exhaust fluid.

This Warranty does not apply to accessories supplied
by Cummins which bear the name of another
company. Such non-warranted accessories include, but
are not limited to: alternators, starters, fans, air
conditioning compressors, clutches, filters,
transmissions, torque converters, vacuum pumps,
power steering pumps, fan drives and air compressors.

Cummins branded alternators and starters are covered
for the first two years from the date of delivery of the Engine to the first user ,or the expiration of the Base Engine Warranty, whichever occurs first.

Failures resulting in excessive oil consumption are not covered beyond the duration of the Coverage or
100,000 miles (160,935 kilometers) or 7,000 hours from
the date of delivery of the Engine to the first user ,
whichever of the three occurs first. Before a claim for excessive oil consumption will be considered, Owner
must submit adequate documentation to show that
consumption exceeds Cummins published standards.

Failures of belts and hoses supplied by Cummins are
not covered beyond the first year from the date of
delivery of the Engine to the first user or the duration of the Warranty, whichever occurs first.

Parts used to repair a Warrantable Failure may be new
Cummins parts, Cummins approved rebuilt parts or
repaired parts. Cummins is not responsible for failures resulting from the use of parts not approved by
Cummins.

A new Cummins or Cummins approved rebuilt part
used to repair a Warrantable Failure assumes the
identity of the part it replaced and is entitled to the remaining Coverage hereunder .

Cummins Inc. reserves the right to interrogate
Electronic Control Module (ECM) data for purposes of
failure analysis.

CUMMINS DOES NOT COVER WEAR OR WEAROUT
OF COVERED PARTS.

CUMMINS IS NOT RESPONSIBLE FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES.

THIS W ARRANTYAND THE EMISSION W ARRANTY

SET FORTH HEREINAFTER ARE THE SOLE

W ARRANTIESMADE BY CUMMINS IN REGARD TO
THESE ENGINES. CUMMINS MAKES NO OTHER

W ARRANTIES,EXPRESS OR IMPLIED, OR OF

MERCHANT ABILITYOR FITNESS FOR A
P ARTICULARPURPOSE.

This Warranty gives you specific legal rights, and you
may also have other rights which vary from state to
state.

Emission
Warranty
Products Warranted
This Emission Warranty applies to new Engines
marketed by Cummins that are used in the United
States** in vehicles designed for transporting persons
or property on a street or highway. This Warranty
applies to Engines delivered to the first user on or after September 1, 1992.

Coverage
Cummins warrants to the first user and each
subsequent purchaser that the Engine is designed,
built and equipped so as to conform at the time of sale by Cummins with all U.S. federal emission regulations
applicable at the time of manufacture and that it is free from defects in material or factory workmanship which
would cause it not to meet these regulations within the longer of the following periods: (A) Five years or
100,000 miles (160,935 kilometers) of operation,
whichever occurs first, as measured from the date of
delivery of the Engine to the first user or (B) The Base Engine Warranty.

If the vehicle in which the Engine is installed is
registered in the state of California, a separate
California Emission Warranty also applies.

Limitations
Failures, other than those resulting from defects in
material or factory workmanship, are not covered by
this Warranty.

Cummins is not responsible for failures or damage
resulting from what Cummins determines to be abuse
or neglect, including, but not limited to: operation
without adequate coolants or lubricants; overfueling;
overspeeding; lack of maintenance of lubricating,
cooling or intake systems; improper storage, starting,
warm-up, run-in or shutdown practices; unauthorized
modifications of the Engine.

Any unauthorized modifications to the aftertreatment
could negatively effect emissions certification and void Warranty.

Cummins is also not responsible for failures caused by
incorrect oil, fuel or diesel exhaust fluid or by water , dirt or other contaminants in the fuel, oil or diesel
exhaust fluid.

Cummins is not responsible for non-Engine repairs,
‘‘downtime’’expenses, cargo damage, fines, all
applicable taxes, all business costs or other losses
resulting from a Warrantable Failure.
923
AGENDA ITEM NO. 28.

Cummins Inc.

Box 3005
Columbus, IN 47202-3005
U.S.A.

Bulletin 3381161
Printed in U.S.A. Rev. 08/09
©2001 Cummins Inc.

CUMMINS IS NOT RESPONSIBLE FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES.
* Airport operated crash trucks and fire department
operated trucks employed to respond to fires,
hazardous material releases, rescue and other
emergency-type situations.
** United States includes American Samoa, the
Commonwealth of Northern Mariana Islands, Guam,
Puerto Rico and the U.S. Virgin Islands.

Cummins Inc.

Box 3005
Columbus, IN 47202-3005
U.S.A.

Bulletin 3381161
Printed in U.S.A. Rev. 08/09
/H230052001 Cummins Inc.
924
AGENDA ITEM NO. 28.
925
AGENDA ITEM NO. 28.
926
AGENDA ITEM NO. 28.
927
AGENDA ITEM NO. 28.
928
AGENDA ITEM NO. 28.

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.

Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.

3. BUYER'S EXCLUSIVE REMEDY.

Fire and Rescue Apparatus
Coverage:

Lifetime Fifty (50) Year Structural Integrity
Chassis Frame & Crossmembers
Fifty (50) Years
(Expected Life of Apparatus)
Warranty Period
Ends After:

The date of the original purchase invoice (issued when the product ships from the factory).Warranty Begins:

Custom chassis frame rail and cross members manufactured by Pierce shall be free from defects in material and
workmanship
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 2/16/2010 WA0038

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.

This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This warranty does not apply to damage caused by corrosion.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4
929
AGENDA ITEM NO. 28.

This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This limited warranty excludes brake pads, brake rotors, seal boots and shock absorbers.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGE S.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE
POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.

Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.

3. BUYER'S EXCLUSIVE REMEDY.
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce.

Three (3) Years
-or-
30,000 Miles
Warranty Period
Ends After:

Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle.
12/16/2013 WA0050
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES

ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.

Fire and Rescue Apparatus
Coverage:

Three (3) Year Material and Workmanship
TAK-4 Independent Front Suspension
Limited Warranty Limited Warranty Limited Warranty Limited Warranty Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

The TAK-4 Front Independent Suspension and Steering
Gears shall be free from defects in material and
workmanship.

1. LIMITED WARRANTY
(b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:
930
AGENDA ITEM NO. 28.

Fire and Rescue Apparatus
Coverage:

SUPPLIER
Limited Warranty
Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

The Meritor axle shall be covered by Meritor as indicated in the attached Meritor warranty coverage description

1. LIMITED WARRANTY
(b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the purchaser who first puts the product in service ("Buyer"):
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; The date of the original purchase invoice (issued when the product ships from the factory).Warranty Begins:

This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

The exclusions listed in the attached Meritor warranty
description shall apply.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.

Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.

3. BUYER'S EXCLUSIVE REMEDY.
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce.

Five (5) YearsWarranty Period
Ends After:

Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 6/29/2020 WA0384
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty. 931
AGENDA ITEM NO. 28.

CUMMINS-MERITOR

COMMERCIAL

VEHICLE SYSTEMS

WARRANTY

COVERAGE FOR THE

UNITED STATES AND CANADA
MODEL YEAR 2024 VEHICLES
932
AGENDA ITEM NO. 28.
2 WARRANTY INFORMATION

TABLE OF CONTENTS
EFFECTIVE MODEL YEAR 2024 VEHICLES
Linehaul .......................................................................................................3 General Service ...........................................................................................6 Heavy Service/Specialty Vehicle ..................................................................9 Fire and Emergency ...................................................................................12 Transit Bus ................................................................................................ 14 Off-highway Service ...................................................................................15 Terms and Conditions ................................................................................17 How to Read Warranty Coverage
Number of Years Mileage (in thousands)
Unl = Unlimited
P = Parts Only
P&L = Parts and Labor
Notice:

Models or components that are approved for use by Cummins-Meritor’s vocational guidelines contained in Cummins-Meritor publication TP-9441 for axles, SP-8320 for trailer axles and TP-12126 for drivelines, or any other products that have an application approval completed with Cummins-Meritor which are not specifically listed, are warranted for one year, unlimited miles, parts only (1/Unl/P).

Products purchased on an incomplete vehicle (glider) are limited to one year, unlimited miles, parts only (1/Unl/P).

Advantage Program
Purchasing additional coverage on select components will continue to safeguard your investment against major repair costs after the initial base coverage expires. You can find out more about the Advantage Program by visiting meritor.com or by contacting Cummins-Meritor at 866-OnTrac1 (866-668-7221) . 933
AGENDA ITEM NO. 28.
3 Linehaul Vehicles
Auto Hauler1
Bulk Hauler1
Chip Hauler1,2
Doubles
Flatbed
General Freight
Grain Hauler1
Livestock Hauler
Moving Van
Pipe Hauler
Refrigerated Freight
Tanker1
Triples
1 Cummins-Meritor classifies these vehicle types as high center of gravity, which require special axle housing considerations. 2 Chip Hauler vehicles require specific axle models listed below and Linehaul condition to be eligible for Linehaul warranty consideration.

Linehaul Typically Is:

High mileage operation (over 60,000 miles/year)
Greater than 30 miles between starts and stops
Maximum grades of 12%
Well maintained highways of concrete or asphalt construction (100% on-road)
Category A job sites, terminals, docks and transfer sites (defined as pavement, concrete or maintained and hard packed gravel).

Note: Category B job sites, terminals, docks, transfer sites (defined as loose or unmaintained sand, dirt or gravel; landfill; farm field; mud; or other similar surfaces) are NOT approved for certain linehaul axle models.

Front Non-Drive Steer Axles – 5/750/P&L
FD-965
FF-941
FF-942
FF-943
FF-944
FF-961
FF-966
FF-967
FG-941
FG-943
MFS-10-122A
MFS-10-143A-N
MFS-10-144A-N
MFS-12-122A-N
MFS-12-122B-N
MFS-12-122C-N
MFS-12E-122A-N
MFS-12E-122B-N
MFS-12E-122C-N
MFS-12-124A-N
MFS-12-132B-N
MFS-12-132C-N
MFS-12E-132B-N
MFS-12E-132C-N
MFS-12-143A-N
MFS-12E-143A-N
MFS-12-144A-N
MFS-13-122A-N
MFS-13-122B-N
MFS-13-122C-N
MFS-13-132B-N
MFS-13-132C-N
MFS-13-143A-N
MFS-13-144A-N
MFS-13B-122B-N
MFS-13B-122C-N
MFS-13B-132B-N
MFS-13B-132C-N
MFS-14-122A-N
MFS-14-122B-N
MFS-14F-122B-N
MFS-14G-122B-N
MFS-14-122C-N
MFS-14F-122C-N
MFS-14G-122C-N
MFS-14-124A-N
MFS-14-132B-N
MFS-14F-132B-N
MFS-14G-132B-N
MFS-14-132C-N
MFS-14F-132C-N
MFS-14G-132C-N
MFS-14-142B-N
MFS-14F-142B-N
MFS-14G-142B-N
MFS-14-142C-N
MFS-14F-142C-N
MFS-14G-142C-N
MFS-14-143A-N
MFS-14-144A-N
Rear Drive Single Axles – 5/750/P&L
MS-19-14X
RS-21-160
MS-23-17H1,2
MS-23-17X2
RS-23-160
RS-23-161
RS-23-185
RS-23-186
Coverage under Cummins-Meritor’s warranty require that
the application of products be properly approved pursuant to OEM and Cummins-Meritor approvals. Refer to TP-9441
for axles, SP-8320 for trailer axles, TP-12126 for drivelines and/or contact Cummins-Meritor regarding specific
application approval questions on any product line.

LINEHAUL

WARRANTY INFORMATION
Vocational Definition of Linehaul
Long distance hauling of food, goods and finished materials Not included are raw ferrous materials, minerals (except oil), sand, gravel, stone, rocks, topsoil, waste or logs Linehaul includes turnpike and hub & spoke
1 Not approved for use in any Category B job sites, terminals, docks or transfer sites. 2 Recommend 11 mm minimum wall thickness for these models used in combination with high center of gravity vehicles and trailing arm suspensions or vehicles operating mainly in Canada.
934
AGENDA ITEM NO. 28.
4 Trailer Axles1
Beam and Brackets 5/500/P , 1/100/L
TPX3000 Axle Series 2 10/Unl/P, 1/Unl/L
Wheel End Systems3
Standard System 4 1/100/P&L
AxlePak5 5/Unl/P&L
AxlePak7 5 7/Unl/P&L
1 For brake components and ABS coverage, refer to appropriate product warranties. 2 Structural components only excluding spindle wear. Spindle wear is 5/Unl/P, 1/Unl/L.
3 Includes hub, wheel seals and wheel bearings—all systems require annual inspections and proper documentation to ensure full coverage. 4 When installed by Cummins-Meritor.
5 When specified with AxlePak7 wheel end system, coverage on Meritor Tire Inflation System (MTIS) thru-tee and stator is 7/Unl/P, 1/Unl/L.

TAG/Pusher Axles1
TQ, TR Beam and Brackets 5/750/P&L
1 For brake components and ABS coverage, refer to appropriate product warranties.

Trailer Mechanical Suspension
Systems1
IMS40 (Integrated Mechanical Suspension – Tandem)2 1/Unl/P&L IMS20 (Integrated Mechanical Suspension – Single)2 1/Unl/P&L 1 For axle coverage, refer to appropriate product warranties. 2 All other suspension components refer to appropriate manufacturer’s warranty.

Trailer Air Suspension Systems
MPA40 (Tandem Axle Parallelogram)1
Major Structural Components 5/500/P, 1/100/L
Curbing Damage Warranty2 5/500/P , 1/100/L
Height Control Valve 1/100/P&L
Shock Absorbers 2/200/P&L
Air Springs 2/200/P , 1/100/L
Bushings 5/Unl/P , 3/Unl/L
PinLoc Air Controls 1/100/P&L
PinLoc Actuator 3/300/P&L
MPA20 (Single Axle Parallelogram)
Major Structural Components 5/500/P, 1/100/L
Height Control Valve 1/100/P&L
Shock Absorbers 2/200/P&L
Air Springs 2/200/P , 1/100/L
Bushings 5/Unl/P , 3/Unl/L
MTA and MTA-Tec6 Trailing Arm Suspension System
Major Structural Components 5/500/P, 1/100/L
Height Control Valve 1/100/P&L
Air Springs 2/200/P , 1/100/L
Bushings 5/500/P , 3/300/L
Shock Absorbers 2/200/P&L
Lift Kit System 1/100/P&L
1 Fastener torque coverage is limited to 2/Unl/P&L when torqued by Cummins- Meritor (For axle and ABS coverage, refer to appropriate product warranties.) 2 “Curbing damage” is defined as deformation (bending, buckling or breakage), caused by sudden impact with a curb or similar fixed object. Damage to the RideSentry slider box (the suspension sliding sub-frame consisting of the frame rails, cross-members and central A-frame assembly), caused by accidental trailer impact with a curb or similar fixed object, is eligible for warranty coverage. Damage to other components or resulting from collision with another vehicle, rollover or fire is not covered under this provision. Warranty is not transferable to another trailer VIN and coverage does not apply if the trailer is deemed to be a total loss, scrapped or otherwise not salvageable.

LINEHAUL

WARRANTY INFORMATION
Rear Drive Tandem/Tridem Axles – 5/750/P&L
RT-40-160/P1,2
RT-46-160/P1,2
RT-46-164/P1,2
RZ-1662
RT-50-160/P1,2
MA-40-165
MA-40-17H3
RZ-188
MA-40-175
MT-34-14X /P4
MT-40-14T/P
MT-40-14X /P4
MT-40-14X /P4
MT-40-14H/E3,4
1 These models required for Chip Hauler and Linehaul warranty consideration. 2 Each vehicle must have a Request for Application Recommendation (RAR) approved by Cummins-Meritor prior to vehicle build. All RARs must identify the chassis number or VIN. Refer to Product Information Letter #303 and #396 for further details. 3 Not approved for use in any Category B job sites, terminals, docks or transfer sites. 4 Recommend 11 mm minimum wall thickness for these models used in combination with high center of gravity vehicles and trailing arm suspensions or vehicles operating mainly in Canada.
935
AGENDA ITEM NO. 28.
5 LINEHAUL

WARRANTY INFORMATION
Brake Components
Cam Q Series Trailer Brakes 5/500/P , 1/100/L
Q+ Drum Brake™1 5/500/P , 1/Unl/P&L
ASA 5/500/P , 1/Unl/P&L
Hubs/Cast Drums and Other Wheel-End Components 1/Unl/P
Hydraulic Disc Brakes 1/Unl/P
All Other Brakes 1/Unl/P
STEELite X30 Drum Brake™2 12-Years or Wearable Life/P
EX+ L and EX+LS Air Disc Brake™3 5/500/P , 1/Unl/L
EX+L Air Disc Brake Extended Standard Warranty 3,4 5/500/P&L 1 For Trailer only, 3/300/P against rust jacking when equipped with Platinum Shield III.
2 Based on stamped wear diameter max.
3 Warranty coverage for boots, seals, caps, bushings and pins is 2/200/P.

Warranty coverage for pads is 1/100/P.
4 Applies only to calipers using friction: MA9300 (EX225LXXXCGXXX).

Drivelines
RPL 5/500/P , 1/Unl/P&L
MXL 3/350/P , 1/Unl/P&L
92N 1/Unl/P
Meritor Tire Inflation System
(MTIS)
MTIS Components 5/Unl/P , 1/Unl/L
936
AGENDA ITEM NO. 28.
6 General Service Vehicles
Auto Hauler
Beverage Truck
Bulk Hauler
Chip Hauler
Cross Country Coach
Flatbed
Front Engine Commercial
Chassis
Front Engine Integral Coach
General Freight
Grain Hauler
Intercity Coach
Intermodal Chassis
Livestock Hauler
Meat Packer
Moving Van
Municipal Truck
Newspaper Delivery
Pick-Up and Delivery
Pipe Hauler
Platform Auto Hauler
Rear Engine Integral Coach
Recreational Vehicles
Refrigerated Freight
School Bus
Stake Truck
Tanker
Tanker Trailer
Tour Bus
Wrecker
General Service Typically Is:

Typically, moderate mileage operation (less than 60,000 miles/year) An average of 3 to 30 miles between starts and stops
Maximum grades of 12%
Generally, on-road service (less than 10% off-road allowed) Category A job sites, terminals, docks and transfer sites (defined as pavement, concrete or maintained and hard packed gravel) or Category B job sites, terminals, docks and transfer sites (defined as loose or unmaintained sand, dirt or gravel; landfill; farm field; mud, or other similar surfaces)
Front Non-Drive Steer Axles – 2/Unl/P&L
FD-965
FF-941
FF-942
FF-943
FF-944
FF-946
FF-961
FF-966
FF-967
FG-941
FH-941
FH-9461
F L-9 41
FL -943
MFS-6-151A-N
MFS-6-153B-N
MFS-6-162B-N
MFS-6-153C-N
MFS-6-162C-N
MFS-7-113C-N
MFS-7-153C-N
MFS-7-163C-N
MFS-8-113B-N
MFS-8-143A-N
MFS-8-153B-N
MFS-8-163B-N
MFS-10-122A
MFS-10-143A-N
MFS-10-144A-N
MFS-12-122A-N
MFS-12E-122A-N
MFS-12-122B-N
MFS-12E-122B-N
MFS-12-122C-N
MFS-12E-122C-N
MFS-12-124A-N
MFS-12-132B-N
MFS-12E-132B-N
MFS-12-132C-N
MFS-12E-132C-N
MFS-12-143A-N
MFS-12-144A-N
MFS-12E-143A-N
MFS-13-122A-N
MFS-13-122B-N
MFS-13B-122B-N
MFS-13-122C-N
MFS-13B-122C-N
MFS-13-132B-N
MFS-13-132C-N
MFS-13B-132B-N
MFS-13B-132C-N
MFS-13-143A-N
MFS-13-144A-N
MFS-14-122A-N
MFS-14-122B-N
MFS-14F-122B-N
MFS-14G-122B-N
MFS-14-122C-N
MFS-14F-122C-N
MFS-14G-122C-N
MFS-14-124A-N
MFS-14-132B-N
MFS-14F-132B-N
MFS-14G-132B-N
MFS-14-132C-N
MFS-14F-132C-N
MFS-14G-132C-N
MFS-14-142B-N
MFS-14F-142B-N
MFS-14G-142B-N
MFS-14-142C-N
MFS-14F-142C-N
MFS-14G-142C-N
MFS-14-143A-N
MFS-14-144A-N
MFS-16-122A-N
MFS-16-133A-N
MFS-16-135A-N
MFS-16-143A-N
MFS-18-133A-N
MFS-18-135A-N
MFS-18-193A-N
MFS-20-133A-N
MFS-20-135A-N
MFS-20-192A-N
MFS-20-193A-N
MFS-22-135A-N
MFS-22H-135A-N
MFS-22-193A-N
MFS-22H-193A-N
1 Can also be used with reduced steer angles in tag position in Coach applications.

GENERAL SERVICE

WARRANTY INFORMATION
Coverage under Cummins-Meritor’s warranty require that
the application of products be properly approved pursuant to OEM and Cummins-Meritor approvals. Refer to TP-9441
for axles, SP-8320 for trailer axles, TP-12126 for drivelines and/or contact Cummins-Meritor regarding specific
application approval questions on any product line.
937
AGENDA ITEM NO. 28.
7 GENERAL SERVICE

WARRANTY INFORMATION
Rear Drive Tandem/Tridem Axles – 2/Unl/P&L
MT-34-14X /P
MT-40-14T/P
MT-40-14X /P
MT-44-14X /P
RT-46-169
MT-52-616
RT-52-1851
MT-58-616
RT-58-1851
MT-70-380
RZ-188
1 Each vehicle must have a Request for Application Recommendation (RAR) approved by Cummins-Meritor prior to vehicle build. All RARs must identify the chassis number or VIN. Refer to Product Information Letter #303 and #396 for further details.

Rear Drive Tandem/Tridem – 3/Unl/P&L
RT-40-160/P RT-46-160/P RT-46-164/P RT-50-160/P RZ-166
Rear Drive Axles – 1/Unl/P&L
RND-14H RND-16A
PTO – 1/Unl/P&L
MPT-170
MPT-180
MPT-185
MPT-309
MPT-500
MPT-518
MPT-1702
Brake Components
Cam Q Series Trailer Brakes1 3/Unl/P, 1/Unl/L
Cam P2 2/200/P
Cam 3/Unl/P
Q+ Drum Brake™ 3/Unl/P&L
Q+ Drum Brake™1,2 2/200/P&L
ASA 3/Unl/P
ASA2 2/200/P
Hubs/Cast Drums and Other Wheel-End Components 1/Unl/P
Hydraulic Disc Brakes 1/Unl/P
All Other Brakes 1/Unl/P
STEELite X30 Drum Brake™3 12-Years or Wearable Life/P
EX+ Air Disc Brake™4 2/Unl/P&L
1 For Trailer only, 3/300/P against rust jacking when equipped with Platinum Shield III or Chassis Protect.
2 Applies to Tour Bus and Cross Country Coach only.
3 Based on stamped wear diameter max.
4 Warranty coverage for boots, seals, caps, bushings and pins is 2/200/P.

Warranty coverage for pads is 1/100/P.

Drivelines
RPL 4/400/P , 1/Unl/P&L
MXL 3/350/P , 1/Unl/P&L
92N 1/Unl/P
Rear Drive Single Axles – 2/Unl/P&L
MS-17-13X
MS-17-14X
MS-19-13X
MS-19-14X
MS-21-13X
MS-21-14X
MS-23-17X
RS-21-160
RC-23-160
RC-23-161
RC-23-1621
RC-23-1651
RS-23-160
RS-23-161
RS-23-185
RS-23-186
RS-24-160
RC-25-160
RS-26-185
MS-26-616
MS-26-616-SP
RS-30-185
MS-30-616
MS-30-616-SP
RS-35-380
1 3/Unl/P&L if PreSet by Cummins-Meritor.
938
AGENDA ITEM NO. 28.
8 Trailer Axles1
Beam and Brackets2 5/Unl/P, 1/Unl/L
TPX4000 Axle Series 3 10/Unl/P, 1/Unl/L
Wheel End Systems4
Standard System 5 1/Unl/P&L
AxlePak5 5/Unl/P&L
AxlePak76 7/Unl/P&L
AxlePak107 10/Unl/P&L
1 For brake components and ABS coverage, refer to appropriate product warranties.
2 9000 Series is 3/Unl/P , 1/Unl/L
3 Structural components only excluding spindle wear. Spindle wear 5/Unl/P, 1/Unl/L.
4 Includes hub, wheel seals and wheel bearings—all systems require annual inspections and proper documentation to ensure full coverage. 5 When installed by Cummins-Meritor.
6 When specified with AxlePak7 wheel end system, coverage on Meritor Tire Inflation System (MTIS) thru-tee and stator is 7/Unl/P, 1/Unl/L. 7 AxlePak10 is limited to Intermodal Chassis applications equipped with TPX4000 series axles.

TAG/Pusher Axles1
TQ, TR Beam and Brackets 3/Unl/P , 1/Unl/L
MC14002, MC16003, FH946 2 2/Unl/P&L
1 For brake components coverage, refer to appropriate product warranties. 2 3/Unl/P&L if sold with PreSet by Cummins-Meritor.

Meritor Tire Inflation System
(MTIS)
MTIS Components 5/Unl/P , 1/Unl/L
Trailer Mechanical Suspension
Systems1
IMS40 (Integrated Mechanical Suspension – Tandem)2 1/Unl/P&L IMS20 (Integrated Mechanical Suspension – Single)2 1/Unl/P&L 1 For axle coverage, refer to appropriate product warranties. 2 All other suspension components refer to appropriate manufacturer’s warranty.

Trailer Air Suspension Systems1
MPA40 (Tandem Axle Parallelogram)2
Major Structural Components 5/Unl/P, 1/Unl/L
Curbing Damage Warranty3 5/500/P , 1/100/L
Height Control Valve 1/Unl/P&L
Shock Absorbers 2/Unl/P&L
Air Springs 2/Unl/P , 1/Unl/L
Bushings 5/P , 3/L
PinLoc Air Controls 1/Unl/P&L
PinLoc Actuator 3/Unl/P&L
MPA20 (Single Axle Parallelogram)
Major Structural Components 5/Unl/P, 1/Unl/L
Height Control Valve 1/Unl/P&L
Shock Absorbers 2/Unl/P&L
Air Springs and Rebound Straps 2/Unl/P , 1/Unl/L
Bushings 5/P , 3/L
MTA and MTA-Tec6 Trailing Arm Suspension System
Major Structural Components 5/Unl/P, 1/Unl/L
Height Control Valve 1/Unl/P&L
Air Springs 2/Unl/P , 1/Unl/L
Bushings 4 5/Unl/P, 3/Unl/L
Shock Absorbers 2/Unl/P&L
Lift Kit System 1/Unl/P&L
1 For axle coverage, refer to appropriate product warranties. 2 Fastener torque coverage is limited to 2/Unl/P&L when torqued by Cummins- Meritor.
3 “Curbing damage” is defined as deformation (bending, buckling or breakage), caused by sudden impact with a curb or similar fixed object. Damage to the RideSentry slider box (the suspension sliding sub-frame, consisting of the frame rails, cross-members and central A-frame assembly), caused by accidental trailer impact with a curb or similar fixed object, is eligible for warranty coverage. Damage to other components or damage resulting from collision with another vehicle, rollover or fire is not covered under this provision. Warranty is not transferable to another trailer VIN and coverage does not apply if the trailer is deemed to be a total loss, scrapped or otherwise not salvageable. 4 Raw wood applications 3/Unl/P, 1/Unl/L

GENERAL SERVICE

WARRANTY INFORMATION
939
AGENDA ITEM NO. 28.
9 Heavy Service/Specialty Vehicles
Airport Rescue Fire
Fighting (ARFF)
Airport Shuttle1
Asphalt Truck
Block Truck
Bottom Dump Trailer
Combination
Cementing Vehicle
Commercial Pick-Up
Concrete Pumper
Construction Material Hauler
Mixer
Demolition
Drill Rig
Dump
Equipment Hauling
Flatbed Trailer Hauler
Flatbed Truck
Fracturing Truck
Front Loader
Geophysical Exploration
Hopper Trailer Combinations
Landscaping Truck
Liquid Waste Hauler
Log Hauling
Lowboy
Michigan Special Gravel
Train
Michigan Special Log Hauler
Michigan Special Steel
Hauler
Michigan Special Waste
Vehicle
Municipal Dump
Rear Loader (Refuse)
Recycling Truck
Residential Pick-Up (Refuse)
Rigging Truck
Roll-Off
Scrap Truck
Semi-End Dump
Sewer/Septic Vacuum
Shuttle Bus1
Side Loader
Snowplow/Snowblower
Steel Hauling
Tanker
Tank Truck
Tractors with Pole Trailers
Tractor/Trailer with Jeeps
Transfer Dump
Transfer Vehicle
Utility Truck
Winch Truck
1 Commercial chassis only
Heavy Service/Specialty Vehicle
Typically Is:

Moderate mileage operation (less than 60,000 miles per year) On/off-road vocations (10% or more off-road)
Moderate to frequent stops/starts (up to 10 stops per mile) An average of three (3) miles between starting and stopping Front Non-Drive Steer Axles – 2/Unl/P&L
FD-965
FF-941
FF-942
FF-943
FF-944
FF-946
FF-961
FF-966
FF-967
FG-941
FG-943
FH-941
FH-946
F L-9 41
FL -943
MFS-6-151A-N
MFS-6-153B
MFS-6-162B
MFS-6-162C
MFS-7-113C-N
MFS-7-153C-N
MFS-7-163C-N
MFS-8-113B-N
MFS-8-153B-N
MFS-8-163B-N
MFS-10-122A
MFS-10-143A-N
MFS-10-144A-N
MFS-12-122
MFS-12E-122
MFS-12-122B-N
MFS-12E-122B-N
MFS-12-122C-N
MFS-12E-122C-N
MFS-12-124A-N
MFS-12-132B-N
MFS-12E-132B-N
MFS-12-132C-N
MFS-12E-132C-N
MFS-12-143A-N
MFS-12-144A-N
MFS-12-155
MFS-13-122
MFS-13-122B-N
MFS-13B-122B-N
MFS-13-122C-N
MFS-13B-122C-N
MFS-13-132B-N
MFS-13B-132B-N
MFS-13-132C-N
MFS-13B-132C-N
MFS-13-143A-N
MFS-13-144A-N
MFS-13-155
MFS-14-122
MFS-14-122B-N
MFS-14F-122B-N
MFS-14G-122B-N
MFS-14-122C-N
MFS-14F-122C-N
MFS-14G-122C-N
MFS-14-124A-N
MFS-14-132B-N
MFS-14F-132B-N
MFS-14G-132B-N
MFS-14-132C-N
MFS-14F-132C-N
MFS-14G-132C-N
MFS-14-142B-N
MFS-14F-142B-N
MFS-14G-142B-N
MFS-14-142C-N
MFS-14F-142C-N
MFS-14G-142C-N
MFS-14-143A-N
MFS-14-144A-N
MFS-16-122A-N
MFS-16-133A-N
MFS-16-135A-N
MFS-16-143A-N
MFS-18-133A-N
MFS-18-135A-N
MFS-18-192A-N
MFS-18-193A-N
MFS-20-133A-N
MFS-20-135A-N
MFS-20-192A-N
MFS-20-193A-N
MFS-22-135A-N
MFS-22H-135A-N
MFS-22-193A-N
MFS-22H-193A-N
RF-16-145
RF-21-160

HEAVY SERVICE/SPECIALTY VEHICLE

WARRANTY INFORMATION
Coverage under Cummins-Meritor’s warranty require that
the application of products be properly approved pursuant to OEM and Cummins-Meritor approvals. Refer to TP-9441
for axles, SP-8320 for trailer axles, TP-12126 for drivelines and/or contact Cummins-Meritor regarding specific
application approval questions on any product line.
940
AGENDA ITEM NO. 28.
10 Rear Drive Axles – 2/Unl/P&L
MS-17-14X
MS-19-14X
MS-21-14X
RS-21-160
RC-23-160
RH-23-160
RS-23-160
RC-23-161
RS-23-161
RS-23-185
RS-23-186/380
RS-24-160
RC-25-160
RS-25-160
MS-26-616
MS-26-616-SP
RS-26-185/380
RC-26-633
MS-30-616
MS-30-616-SP
RS-30-185/380
MS-35-380
RS-38-380
MT-58-616
MT-58-616-SP
Rear Drive Axles – 1/Unl/P&L
RND-14H RND-16A
Rear Drive Tandem/Tridem Axles – 2/Unl/P&L
MT-34-14X /P
MT-40-14T/P
MT-40-14X /P
MT-44-14X /P
RT-46-169
RT-58-160
MT-52-616
MT-52-616-SP
RT-52-185/3801,2
MT-58-616
MT-58-616-SP
RT-58-185/3801,2
RT-70-380
MT-70-380
RZ-188
1 Axle model designated will vary according to options and variations specified on these axles. Contact Cummins-Meritor Axle Applications Engineering for details. 2 Each vehicle must have a Request for Application Recommendation (RAR) approved by Cummins-Meritor prior to vehicle build. All RARs must identify the chassis number or VIN. Refer to Product Information Letter #303 and #396 for further details.

Rear Drive Tandem/Tridem – 3/Unl/P&L
RT-40-160/P/A3 RT-46-160/P/A1,3 RT-46-164/P2,3 RT-50-160/P/A3 RZ-166 1 U.S. only. Canadian warranty = 1/Unl/P for combination vehicles only. 2 Axle model designated will vary according to options and variations specified on these axles. Contact Cummins-Meritor Axle Applications Engineering for details. 3 Each vehicle must have a Request for Application Recommendation (RAR) approved by Cummins-Meritor prior to vehicle build. All RARs must identify the chassis number or VIN. Refer to Product Information Letter #303 and #396 for further details.

Front Drive Steer Axles – 1/Unl/P&L
MX-08-130-FV (FSD-08A)
MX-10-130-FV (FSD-10A)
MX-12-130-FV (FSD-12A)
MX-13-130-FV (FSD-13A)
MX-14-130-FV (FSD-14A)
MX-16-130-FV (FSD-16A)
MX-18-130-FV (FSD-18A)
MX-18-130-SD (SDA-1800)
MX-20-130-FV (FSD-20A)
MX-21-130-FV (FSD-21A)
MX-21-130-SD (SDA-2100)
MX-23-130-FV (FSD-23A)
MX-23-130-SD (SDA-2300)

HEAVY SERVICE/SPECIALTY VEHICLE

WARRANTY INFORMATION
MX-10-120
MX-10-120 EVO
MX-12-120
MX-12-120 EVO
MX-14-120
MX-14-120 EVO
MX-16-120
MX-18-120
MX-17-140
MX-19-140
MX-21-140
MX-21-160
MX-23-160
MX-23-810
Front Drive Steer Axles – 2/Unl/P&L
MPT-170
MPT-180
MPT-185
MPT-309
MPT-500
MPT-518
MPT-1702
PTO – 1/Unl/P&L
941
AGENDA ITEM NO. 28.
11 Drivelines
RPL 3/Unl/P , 1/Unl/P&L
92N 1/Unl/P&L
MXL 1/Unl/P&L
Transmission – 1/Unl/P&L
FAT 30
Brake Components
Cam P 3/Unl/P
Cam P 2/100/P
Cam Cast Plus™ 2/100/P&L
Q+ Drum Brake™1 3/Unl/P&L
Q+ Drum Brake™2 2/100/P&L
ASA 3/Unl/P
ASA2 2/100/P
Hubs/Cast Drums and Other Wheel-End Components 3 1/Unl/P Hydraulic Disc Brakes 1/Unl/P
All Other Brakes 1/Unl/P
EX+ Air Disc Brake4 2/100/P&L
1 For Trailer only, 3/300/P against rust jacking when equipped with Platinum Shield III.
2 Applies to City Bus, Trolley, Shuttle Bus and Airport Shuttle only. 3 Based on stamped wear diameter max.
4 Warranty coverage for boots, seals, caps, bushings and pins is 2/100/P.

Warranty coverage for pads is 1/100/P.

Trailer Axles1
Beam and Brackets2 5/Unl/P, 1/Unl/L
Wheel End Systems3
Standard System 4 1/Unl/P&L
1 For brake components coverage, refer to appropriate product warranties. 2 9000 Series is 3/Unl/P , 1/Unl/L
3 Includes hub, wheel seals and wheel bearings—all systems require annual inspections and proper documentation to ensure full coverage. 4 When installed by Cummins-Meritor.

Trailer Air Suspension Systems1
MTA and MTA-Tec6 Trailing Arm Suspension System
Major Structural Components 2 5/500/P , 1/100/L
Height Control Valve 1/100/P&L
Air Springs 2/200/P , 1/100/L
Bushings 2 5/500/P , 3/300/L
Shock Absorbers 2/200/P&L
Lift Kit System 1/100/P&L
1 For axle coverage, refer to appropriate product warranties. 2 Raw wood applications 3/Unl/P, 1/Unl/L
Meritor Tire Inflation System
(MTIS)
MTIS Components 5/Unl/P , 1/Unl/L
Gearboxes – 1/Unl/P&L
MGX-402
MGX-423
MGX-450
MGX-451
MGX-466
MGX-479
MGX-538
Transfer Cases – 1/Unl/P
MTC-2212-CV (306)
MTC-3106-FV (TC-137)
MTC-3111 (T-2111)
MTC-3112-CV (548C)
MTC-3116 (T-2111 through-shaft)
MTC-3118-FV (TC-180 and TC-180-23)
MTC-3118-CV (358)
MTC-3120-FV (TC-143)
MTC-3124 (T-2119)
MTC-3203
MTC-3205-GV (MTC-25/RTC-25)
MTC-3206-FV (TC-237)
MTC-3206-CS (544)
MTC-3208-GV (RTC-50)
MTC-3209-GV (MTC-60/RTC-60)
MTC-3212-CV (315 and 548B)
MTC-3312-FV (TC-270)
MTC-3220-FC (TC-142)
MTC-4206-FV (TC-38)
MTC-4208
MTC-4210
MTC-4213

HEAVY SERVICE/SPECIALTY VEHICLE

WARRANTY INFORMATION
942
AGENDA ITEM NO. 28.
12 Fire and Emergency Vehicles
Aerial Ladder Truck
Aerial Platform
Ambulance
Command Vehicle
Crash Fire Rescue
Pumper
Rapid Intervention
Vehicle (RIV)
Tanker
Fire and Emergency Typically Is:

Lower mileage operations (less than 20,000 miles/year)
Generally, on-road service (less than 10% off-road)
An average of three (3) miles between starting and stopping Front Non-Drive Steer Axles – 5/Unl/P&L
F L-9 41
FL -943
MFS-18-133A-N
MFS-18-135A-N
MFS-18-193A-N
MFS-20-133A-N
MFS-20-135A-N
MFS-20-193A-N
MFS-22-135A-N
MFS-22H-135A-N
MFS-22-193A-N
MFS-22H-193A-N
Rear Drive Single Axles – 5/Unl/P&L
RC-23-160
RS-23-160
RS-23-161
RS-23-185
RS-23-186
RS-24-160
RC-25-160
RS-26-185
RS-30-185
RS-35-1851
RS-25-160
1 2/Unl/P&L if PreSet by Cummins-Meritor.

Rear Drive Tandem/Tridem Axles – 5/Unl/P&L
MT-40-14X /P
RT-40-160/P
MT-44-14X /P
RT-46-160/P
RT-46-164/P
RT-46-169
RT-50-160/P
MT-52-616
RT-52-1851
MT-58-616
RT-58-1851
MT-70-3802
1 Each vehicle must have a Request for Application Recommendation (RAR) approved by Cummins-Meritor prior to vehicle build. All RARs must identify the chassis number or VIN. Refer to Product Information Letter #303 and #396 for further details. 2 2/Unl/P&L
Front Drive Steer Axles – 2/Unl/P&L
MX-19-140 MX-21-140 MX-21-160 MX-23-160 MX-23-810

FIRE AND EMERGENCY

WARRANTY INFORMATION
Coverage under Cummins-Meritor’s warranty require
that the application of products be properly approved
pursuant to OEM and Cummins-Meritor approvals.

Refer to TP-9441 for axles, TP-12126 for drivelines
and/or contact Cummins-Meritor regarding specific
application approval questions on any product line.

Transfer Cases – 1/Unl/P
MTC-2212-CV (306)
MTC-3106-FV (TC-137)
MTC-3111 (T-2111 through-shaft)
MTC-3112-CV (548C)
MTC-3118-FV (TC-180 and TC-180-23)
MTC-3118-CV (358)
MTC-3120-FV (TC-143)
MTC-3124 (T-2119)
MTC-3206-FV (TC-237)
MTC-3206-CS (544)
MTC-3208-GV (RTC-50)
MTC-3209-GV (MTC-60/RTC-60)
MTC-3212-CV (315 and 548B)
MTC-3312-FV (TC-270)
MTC-3220-FC (TC-142)
MTC-4206-FV (TC-38)
MTC-4208
MTC-4210
MTC-4213
943
AGENDA ITEM NO. 28.
13 PTO – 1/Unl/P&L
MPT-170
MPT-180
MPT-185
MPT-309
MPT-500
MPT-518
MPT-1702

FIRE AND EMERGENCY

WARRANTY INFORMATION
Brake Components
Cam 3/Unl/P
Q+ Drum Brake™ 3/Unl/P&L
ASA 3/Unl/P
Hubs/Cast Drums and Other Wheel-End Components 1/Unl/P
Hydraulic Disc Brakes 1/Unl/P
All Other Brakes 1/Unl/P
EX+ Air Disc Brake™1 2/Unl/P&L
1 Warranty coverage for boots, seals, caps, bushings and pins is 2/200/P.

Warranty coverage for pads is 1/100/P.

Drivelines
RPL 4/400/P , 1/Unl/L
MXL 3/350/P , 1/Unl/L
92N 1/Unl/P
944
AGENDA ITEM NO. 28.
14 Transit Bus Vehicles
Airport Shuttle
City Bus
Commuter Coach
Shuttle Bus
Transit Bus Trolley
Transit Bus Typically Is:

Moderate mileage operation (less than 50,000 miles per year) Moderate to frequent stops/starts (up to 10 stops per mile) Front Non-Drive Steer Axles – 5/300/P&L
FH-946 FH-9411 MFS-12-155 MFS-13-155
1 Commuter coach only – 2/Unl/P&L
Tag Axles – 2/Unl/P&L
Brake Components
Cam Cast Plus™ 2/100/P&L
Q+ Drum Brake™1 2/100/P&L
ASA1 2/100/P
Hubs/Cast Drums and Other Wheel-End Components 1/Unl/P
All Other Brakes 1/Unl/P
EX+ Air Disc Brake2 2/100/P&L
1 Applies to City Bus, Trolley, Shuttle Bus and Airport Shuttle only. 2 Warranty coverage for boots, seals, caps, bushings and pins is 2/100/P.

Warranty coverage for pads is 1/100/P.

Drivelines
RPL 3/Unl/P , 1/Unl/L
92N 1/Unl/P&L
MXL 1/Unl/P&L
1 Commuter coach only – 2/Unl/P&L
Rear Drive Single Axles – 5/300/P&L
RS-23-160
RC-23-161
71163
79163
RC-23-1621
RC-23-1651
RS-21-160
MC-14002 MC-16003 FH-946
Center Non-drive Axles – 5/300/P&L
MC-26000 71063 79063
Gearboxes – 1/Unl/P&L
MGX-450 MGX-451 MGX-538

TRANSIT BUS

WARRANTY INFORMATION
Coverage under Cummins-Meritor’s warranty require
that the application of products be properly approved
pursuant to OEM and Cummins-Meritor approvals.

Refer to TP-9441 for axles, TP-12126 for drivelines
and/or contact Cummins-Meritor regarding specific
application approval questions on any product line.
945
AGENDA ITEM NO. 28.
15 Industrial and Off-Highway Service Vehicles
Load-On/Load-Off
Port Tractor
Rail Yard Spotter
Roll-On/Roll-Off
Stevedoring Tractor
Trailer Spotter
Yard Jockey
All and Rough
Terrain Cranes
Forestry
Material Handling
Specialized Heavy
Haul
Excavator
Compactor
Fertilizer Spreader
Snow Blower
Mining and
Specialized Mining
Rail Car Mover
Loader
Tow Tractor
Pushback Tractor
Industrial and Off-Highway Service Typically Is:

Low mileage operation
Low speed vehicle speed restriction
Vehicles are not typically licensed for highway use
Six (6) starts/stops per mile (typical)
Front Non-Drive Steer Axles – 1/Unl/P
FF - 941
FF - 943
FF - 961
FF - 966
FG - 941
FG - 943
FL - 941
FL - 943
FN - 951
FS-25
MFS-20-133A-N
MFS-20-135A-N
MFS-20-192A-N
MFS-20-193A-N
MFS-22-135A-N
MFS-22H-135A-N
MFS-22-193A-N
MFS-22H-193A-N
MON-Z0 FAMILY
Gearboxes – 1/Unl/P&L
MGX-402
MGX-423
MGX-450
MGX-451
MGX-466
MGX-479
MGX-538
PTO – 1/Unl/P&L
MPT-170
MPT-180
MPT-185
MPT-309
MPT-500
MPT-518
MPT-1702
1 2/Unl/P for LO/LO Terminal Tractor applications
Planetary Axles – 1/Unl/P
MOB
MOC
MOD
MOE
MOF
MOG
MOH
MOR
MOS
MOT
MOX
MOY
MOZ
Rear Drive Axles – 1/Unl/P
MT-14X1
RS-23-186
RS-23-380
RS-24-160
RS-30-185
RS-30-380
RT-1451
RT-1601

OFF-HIGHWAY SERVICE

WARRANTY INFORMATION
Coverage under Cummins-Meritor’s warranty require that the application of products be properly approved pursuant to OEM and Cummins-Meritor approvals. Contact Cummins-Meritor regarding specific application approval questions on any product line. 946
AGENDA ITEM NO. 28.
16 Drivelines – 1/Unl/P

RPL MXL
Transmission – 1/Unl/P&L
FAT 30
Brake Components
Cam 3/Unl/P
Q+ Drum Brake™ 3/Unl/P&L
ASA 3/Unl/P
Hubs/Cast Drums and Other Wheel-End Components 1/Unl/P
Hydraulic Disc Brakes 1/Unl/P
All Other Brakes 1/Unl/P

OFF-HIGHWAY SERVICE

WARRANTY INFORMATION
Transfer Cases – 1/Unl/P
MTC-2212-CV (306)
MTC-3106-FV (TC-137)
MTC-3111 (T-2111 through-shaft)
MTC-3112-CV (548C)
MTC-3116 (T-2111)
MTC-3118-FV (TC-180 and TC-180-23)
MTC-3118-CV (358)
MTC-3120-FV (TC-143)
MTC-3124 (T-2119)
MTC-3206-FV (TC-237)
MTC-3208-GV (RTC-50)
MTC-3209-GV (MTC-60/RTC-60)
MTC-3220-FC (TC-142)
947
AGENDA ITEM NO. 28.
17 Coverage Exclusions
Product Description
All
The cost of any repairs, replacements or adjustments to a covered component (1) associated with noise; (2) resulting from the use or installation of non-genuine Cummins-Meritor components or materials; (3) due to vibration associated with improper operation or misapplication of drivetrain components; and (4) damage resulting from corrosion.

For axle assemblies supplied by Cummins-Meritor with suspension and interface brackets designed and/or attached by non- Cummins-Meritor parties, Cummins-Meritor warranty coverage does not apply to the brackets, bracket attachment methods and field issues caused by brackets or bracket attachments to any covered component unless specified in a separate OEM agreement.

Front Axles1
Linehaul – King Pin Bushings 1yr/Unl P&L
All Other Vocations – King Pin Bushings Excluded
1 King Pin Bushing wear excluded for all vocations.

Rear Axles
Self-contained traction equalizers and oil filters. The use of NoSPIN differentials will result in the exclusion of axle shafts from warranty considerations. NoSPIN is a product of Eaton.

ASA
Boot and bushing. Bent, broken, over-torqued, missing or otherwise damaged pawl assemblies.

Cam Brake
Brake lining wear and brake shoe “rust-jacking.”
Disc Brake
Pad wear, rotor wear.

Coverage Limitations
Product Description
All
Any claim beyond 60 days from date of repair will not be accepted or honored under this warranty program. Products purchased on an incomplete vehicle (glider) are limited to one year, unlimited miles parts only (1/Unl/P).

Warranty coverage on vehicles with 1,850 lb-ft engine torque and over may be reduced on individual drivetrain components. Contact your Cummins-Meritor representative for specific details.

Front Axles
Tie rod and tie rod ends limited to 3-year/300,000-mile or published vocational coverage, whichever is less. Wheel seals, gaskets and wheel bearings are covered for 1 year/unlimited miles if the wheel end equipment is supplied and assembled by Cummins-Meritor.

Rear Axles
Pinion and through shaft seals limited to 3-year/300,000-mile or published vocational coverage, whichever is less, if yoke is installed by Cummins-Meritor. If yoke is not installed by Cummins- Meritor, then Cummins-Meritor does not warrant pinion seals.

Wheel seals, gaskets and wheel bearings are covered for 1 year/unlimited miles if the wheel end equipment is supplied and assembled by Cummins-Meritor.

Rear Axles
The Cummins-Meritor breather part number A-2297-C-8765 with A-3196-J-1336 hose must be used for eligibility of any potential warranty consideration relating to contamination and/or loss of lube in axles.

Cam Brake
Limited to bracket, brake spider and camshaft structural integrity.

STEELite X30
Wearable life is up to the discard diameter of the drum.

Terms and Conditions
(1) What is Covered by this Commercial Warranty?
Meritor Heavy Vehicle Systems, LLC warrants to the owner (“Owner”) that the components listed in this publication, which have been installed by an Original Equipment Manufacturer (“OEM”) as original equipment in vehicles licensed for on-highway use, will be free from defects in material and workmanship. This warranty coverage begins only after the expiration of the OEM’s vehicle warranty for the applicable covered components. Warranty coverage ends at the expiration of the applicable time period from the date of vehicle purchase by the first Owner or the applicable mileage limitation, whichever occurs first. Duration of coverage varies by component and vocation as detailed elsewhere in this warranty statement.

Some components are warranted for parts only and the Owner must pay any labor costs associated with the repair or replacement of the component.

Other components are warranted for both parts and reasonable labor to repair or replace the subject component. Components (whether new, used or remanufactured) installed as replacements under this warranty are warranted only for the remainder of the original period of time or mileage under the original warranty.

For certain components, coverage requires the use of specific extended drain interval or synthetic lubricants. For further information about lubrication and maintenance, see Cummins-Meritor publication Maintenance Manual Number l and the applicable Cummins-Meritor maintenance manual for the product in question. Other conditions and limitations applicable to this warranty are detailed below.

TERMS AND CONDITIONS
948
AGENDA ITEM NO. 28.

Product models, brands, names and trademarks depicted herein are the property of their respective owners and, except where otherwise indicated, are not in any way associated with Meritor Heavy Vehicle Systems, LLC, or any parent or affiliate, thereof. (2) Designation of Vocational Use Required
To obtain warranty coverage, each Owner must notify Cummins-Meritor through the OEM new truck and/or trailer dealer of the intended vocational use of the vehicle into which the Cummins-Meritor components have been incorporated prior to the vehicle in-service date. This notification may be accomplished by registering the vehicle through your OEM new truck and/or trailer dealer or with Cummins-Meritor directly. Failure to notify Cummins- Meritor of (I) the intended vocational use of the vehicle or (II) a change in vocational use from that which was originally designated, will result in the application of a one year, unlimited mileage, parts only warranty (1/Unl/P) from the initial in-service date.

A second Owner and each subsequent Owner must also notify Cummins- Meritor as to the intended vocational use of the vehicle. This notification can be sent directly to Cummins-Meritor or through the OEM new truck and/ or trailer dealer. The duration and mileage coverage of this warranty cannot exceed the coverage extended to the first Owner after his or her initial designation of vocational use.

Coverage under Cummins-Meritor’s warranty requires that the application of products be properly approved pursuant to OEM and Cummins-Meritor approvals. Refer to TP-9441 for axles, SP-8320 for trailer axles, TP-12126 for drivelines and/or contact Cummins-Meritor regarding specific application approval questions on any product line.
(3) What is the Cost of this Warranty?
There is no charge to the Owner for this warranty.
(4) What is not Covered by this Warranty?
This warranty does not cover normal wear and tear; nor does it cover a component that fails, malfunctions or is damaged as a result of (I) improper installation, adjustment, repair or modification (including the use of unauthorized attachments or changes or modification in the vehicle’s configuration, usage or vocation from that which was originally approved by Cummins-Meritor), (II) accident, natural disaster, abuse or improper use (including loading beyond the specified maximum vehicle weight or altering engine power settings to exceed the axle and/or driveline capacity) or (III) improper or insufficient maintenance (including deviation from approved lubricants, change intervals or lube levels). This warranty does not cover any component or part that is not branded by Cummins-Meritor. For vehicles that operate full or part time outside of the United States and Canada, a one year, unlimited mileage, parts only warranty (1/Unl/P) will apply.
(5) Remedy
The exclusive remedy under this warranty shall be the repair or replacement of the defective component at Cummins-Meritor’s option. Cummins-Meritor reserves the right to require that all applicable failed materials are available and/or returned to Cummins-Meritor for review and evaluation. (6) Disclaimer of Warranty

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES

OR CONDITIONS, EXPRESSED, IMPLIED OR STATUTORY INCLUDING

ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
PARTICULAR PURPOSE.
(7) Limitation of Remedies
In no event shall Cummins-Meritor be liable for special, incidental, indirect or consequential damages of any kind or under any legal theory, including, but not limited to, towing, downtime, lost productivity, cargo damage, taxes or any other losses or costs resulting from a defective covered component. (8) To Obtain Service
If the Owner discovers within the applicable coverage period a defect in material or workmanship, the Owner must promptly give notice to either Cummins-Meritor or the dealer from which the vehicle was purchased. To obtain service, the vehicle must be taken to any participating OEM new truck and/or trailer dealer or authorized Cummins-Meritor service location. The dealer will inspect the vehicle and contact Cummins-Meritor for an evaluation of the claim. When authorized by Cummins-Meritor, the dealer will repair or replace during the term of this warranty any defective Cummins-Meritor component covered by this warranty.
(9) Entire Agreement
This is the entire agreement between Cummins-Meritor and the Owner about warranty and no Cummins-Meritor employee or dealer is authorized to make any additional warranty on behalf of Cummins-Meritor. This agreement allocates the responsibilities for component failure between Cummins-Meritor and the Owner.

TERMS AND CONDITIONS
Cummins Inc.

Box 3005
Columbus, IN 47202-3005
U.S.A.
cummins.com
SP-95155
Bulletin 6451105 Produced in U.S.A. Rev. 1/24
©2024 Meritor, Inc.
949
AGENDA ITEM NO. 28.
)LUHDQG5HVFXH$SSDUDWXV
Coverage:
7KUHH

<HDU0DWHULDODQG:RUNPDQVKLS
0HULWRU:DEFR$%6%UDNH6\VWHP
Limited Warranty
Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

The Meritor Wabco ABS brake system shall be covered by
Meritor Wabco as indicated in the attached Meritor Wabco warranty coverage description
/,0,7(':$55$17<
(b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; The date of the original purchase invoice (issued when the product ships from the factory).Warranty Begins:
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce.

Three (3) YearWarranty Period
Ends After:

The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

The exclusions listed in the attached Meritor Wabco warranty description shall apply.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4
(;&/86,212)&216(48(17,$/$1',1&,'(17$/'$0$*(6
Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE
POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.

Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.
%8<(5
6(;&/86,9(5(0('<
Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle.
2/25/2013 WA0232
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES

ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.
',6&/$,0(562):$55$17,(6
capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty. 950
AGENDA ITEM NO. 28.

WARRANTY
Warranty coverage is essential to protecting your investment. But understanding the full details of your coverage can be challenging. This straightforward approach allows you, our valued customer, to better understand how your specific vehicle applications will be covered in your region. Our component warranty coverage is provided according to vocation/usage categories listed below. • Linehaul covers high mileage operation (over 60,000 miles/year) on well-maintained major highways of concrete or asphalt construction.
• General Service covers moderate mileage operations (less than 60,000 miles/year) on well-maintained public roads (less than 10 percent off-road) typically with less than three (3) stops per mile. • Heavy Service (Vocational) covers vehicles with more than 10 percent off-road OR moderate to frequent starts/stops typically with more than three (3) stops per mile.
• Off-Highway Service covers lower mileage operations. Vehicles are not typically licensed for highway use. • The standard aftermarket warranty for WABCO products - including WABCO Original parts, WABCO Reman Solutions, ProVia quality aftermarket parts and WABCO retrofit solutions - is one year, parts only from in-service date when purchased from ZF distributor networks or its affiliates and/or subsidiaries.

MODEL YEAR 2021 VEHICLES
How to Read Warranty Coverage (Example)
Number of Years Mileage (in thousands) Unl=Unlimited P=Parts Only P&L=Parts & Labor 3 300 P
951
AGENDA ITEM NO. 28.

WARRANTY - MODEL YEAR 2021 VEHICLES
¹ ZF and WABCO branded components.
2 WABCO compressors installed on Cummins, Mercedes, and DDC engines are not warranted or serviced by ZF. Please contact your respective dealer/distributor of those engines for warranty and servicing. 3 An extended warranty of 4/400/P will apply when a WABCO Trailer Control Line Filter is used in combination with a WABCO Trailer ABS valve.
• Aerial Ladder Truck
• Aerial Platform
• Ambulance
• Auto Hauler
• Beverage Truck
• Bulk Hauler
• Chip Hauler (Truck)
• Cross Country Coach
• Doubles
• Flatbed
• Front Engine Commercial
Chassis
• Front Engine Integral
Coach
• General Freight
• Grain Hauler
• Intercity Coach
• Intermodal Chassis
• Livestock Hauler
• Meat Packer
• Moving Van
• Municipal Truck
• Pipe Hauler
• Platform Auto Hauler
• Pumper
• Rear Engine Integral Coach
• Recreational Vehicles
• Refrigerated Freight
• School Bus
• Stake Truck
• Tanker
• Tanker Truck
• Triples
• Tour Bus
• Wrecker

LINEHAUL/GENERAL SERVICE VEHICLES

LINEHAUL/GENERAL SERVICE WARRANTY INFORMATION

LINEHAUL TYPICALLY IS
• High mileage operation (over 60,000 miles/year)
• Well maintained major highways of concrete or
asphalt construction

GENERAL SERVICE TYPICALLY IS
• Moderate mileage operations (less than 60,000 miles/year) • Well maintained public roads (less than 10% off-road) • Less than three (3) stops per mile
WABCO Components1
Air Management
Air Brake Valves
1/100/P&LTrailer Lift Axle Control Valve
Trailer Control Line Filter3
Air Compressors (ALL)2 2/200/P&L
Air Dryers (ALL) 3/300/P&L
Aerodynamics
OptiFlow® TrailerSkirt 2/UnU/P
OptiFlow® Trailer Tail and AutoTail 2/UnI/P
Braking Systems
ABS (Anti-Lock Braking System) Air
3/300/P&L
ABS (Anti-Lock Braking System) Hydraulic
Electronic Braking System (EBS)
Electronic Stability Control (ESC)
Roll Stability Control (RSS)
Trailer Roll Stability Support (RSS)
Trailer ABS (Anti-Lock Braking System)
3 Driveline Suspension Control
Clutch Controls 2/200/P&L
Leveling Valves
1/100/P&L
OptiRide® Automated Manual Transmission (AMT)
OptiRide® Electronically Controlled Air Suspension
(ECAS) 3/300/P&L
WABCO Components1 (cont.)
Safety
OnGuardACTIVE®
3/300/P&L
OnLane®
OnLaneALERT®
OnSide®
Trailer SafeStart™
Trailer TailGUARD™
Telematics
TrailerCAST™ Telematics Device 3/300/P&L
Wheel End Solutions
EasyFit™ Slack Adjuster 6/600/P
MAXXUS™ Truck Air Disc Brake 5/500/P&L
IVTM - Wheel Module 6/P
IVTM - All Other Products 2/P
Pan 17 and 19 Air Disc Brake 2/Unl/P and
1/Unl/L
Pan 22 Air Disc Brake 5/500/P and 1/L
TRISTOP™ D Actuator w/ IBV or IRB 6/600/P
TRISTOP™ D Actuator 3/300/P
UNISTOP™ Actuator 2/200/P
Trailer MAXX22T™ Air Disc Brake 5/500/P and 1/L
952
AGENDA ITEM NO. 28.
1 ZF and WABCO branded components. 2 WABCO compressors installed on Cummins, Mercedes, and DDC engines are not warranted or serviced by ZF. Please contact your respective dealer/distributor of those engines for warranty and servicing. 3 An extended warranty of 4/400/P will apply when a WABCO Trailer Control Line Filter is used in combination with a WABCO Trailer ABS valve.

WABCO Components1
Air Management
Air Brake Valves
1/100/P&L
Air Compressors (ALL)2
Air Dryers (ALL)
Trailer Control Line Filter3
Braking Systems
ABS (Anti-Lock Braking System) Air 3/300/P&L
ABS (Anti-Lock Braking System) Hydraulic 2/200/P&L
Electronic Braking System (EBS)
3/300/P&L
Electronic Stability Control (ESC)
Trailer ABS Valve3
Roll Stability Control (RSS)
Trailer Roll Stability Support (RSS)
Driveline Suspension Control
OptiRide® Electronically Controlled Air Suspension
(ECAS) 2/200/P&L
Leveling Valves 1/100/P&L
Clutch Controls 2/200/P&L
Safety
OnGuardACTIVE®
3/300/P&L
OnLane®
OnLaneALERT®
OnSide®
Trailer SafeStart™
Trailer TailGUARD™
Telematics
TrailerCAST™ Telematics Device 3/300/P&L
Wheel End Solutions
EasyFit™ Slack Adjuster 2/200/P
MAXXUS™ Air Disc Brake 1/Unl/P&L
IVTM - Wheel Module 6/P
IVTM - All Other Products 2/P
Pan 22, 19 and 17 Air Disc Brake 1/Unl/P&L
Trailer MAXX22T™ 1/Unl/P&L
TRISTOP™ D Actuator w/ IBV 3/Unl/P
TRISTOP™ D Actuator 2/200/P
UNISTOP™ Actuator 1/100/P
• Airport Rescue Fire (ARF)
• Airport Shuttle
• Asphalt Truck
• Block Truck
• Bottom Dump Trailer
Combination
• Cementing Vehicle
• City Bus
• Commercial Pick-Up
• Concrete Pumper
• Construction Material Hauler
• Crash Fire Rescue (CFR)
• Mixer
• Demolition
• Drill Rig
• Dump
• Emergency Service
• Equipment Hauling
• Flatbed Trailer Hauler
• Flatbed Truck
• Fracturing Truck
• Front Loader
• Geophysical Exploration
• Hopper Trailer Combinations
• Landscaping Truck
• Liquid Waste Hauler
• Log Hauling
• Lowboy
• Michigan Special
Gravel Trains
• Michigan Special
Log Hauler
• Michigan Special
Steel Hauler
• Michigan Special
Waste Vehicle
• Municipal Dump
• Newspaper Delivery
• Package Delivery
• Pick-up and Delivery
• Rapid Intervention
Vehicle (RIV)
• Rear Loader
• Recycling Truck
• Residential Pick-Up/Waste
• Rigging Truck
• Roll-Off
• Scrap Truck
• Semi-End Dump
• Sewer/Septic Vacuum
• Shuttle Bus
• Side Loader
• Snowplow/Snowblower
• Steel Hauling
• Tanker
• Tank Truck
• Tractors with Pole Trailers
• Tractor/Trailer with Jeeps
• Transfer Dump
• Transfer Vehicle
• Transit Bus
• Trolley
• Utility Truck
• Winch Truck

HEAVY SERVICE VEHICLES

HEAVY SERVICE (VOCATIONAL) WARRANTY INFORMATION

HEAVY SERVICE TYPICALLY IS
• On/Off road vocations (10% or more off-road) OR
• Moderate to frequent starts/stops typically more than three (3) stops per mile
953
AGENDA ITEM NO. 28.

WARRANTY - MODEL YEAR 2021 VEHICLES

INDUSTRIAL AND OFF-HIGHWAY SERVICE

TYPICALLY IS
• Low mileage operation3
• Vehicles are not typically licensed for highway use
¹ ZF and WABCO branded components. 2 WABCO compressors installed on Cummins, Mercedes, and DDC engines are not warranted or serviced by ZF. Please contact your respective dealer/distributor of those engines for warranty and servicing. 3 Equivalent hours of service limit: 2,000 hours for all components.

INDUSTRIAL/OFF-HIGHWAY SERVICE WARRANTY INFORMATION
WABCO Components1
Air Management
Air Brake Valves
2/Unl/PAir Compressors (ALL)2
Air Dryers (ALL)
Brake Actuation
Air/Hydraulic Actuators
2/Unl/P
Master Cylinders
Remote Actuators
Slave and Wheel Cylinders
Two Fluid Actuators
Brake Locks
Brake Locks (ALL)
2/Unl/PElectric Brake Locks
Lever Locks
Braking Systems
ABS (Anti-Lock Braking System) Air
1/100/P&L
ABS (Anti-Lock Braking System) Hydraulic
Driveline Suspension Control
Clutch Controls
1/100/P&L
Leveling Valves
Electrohydraulics & Controls
Electronic Pedals
2/Unl/PElectrohydraulic Brake Valves (EBV)
Pressure Switches
Hydraulic Braking Solutions
Accumulator Charging Valves
2/Unl/PHydraulic Throttle Controls and Switches
Modulating Brake Valves
Wheel End Solutions
EasyFit™ Slack Adjuster 2/200/P
Caliper Disc Brakes 2/Unl/P
MAXXUS™ Air Disc Brake 1/Unl/P&L
Multiple Disc Brakes 2/Unl/P
IVTM - Wheel Module 6/P
IVTM - All Other Products 2/P
Pan 22, 19 and 17 Air Disc Brake 1/Unl/P&L
TRISTOP™ D Actuator w/ IBV 3/Unl/P
TRISTOP™ D Actuator 2/200/P
UNISTOP™ Actuator 1/100/P
Market Common Application Types
Agriculture
Fertilizer Spreader, Tractor, Heavy Duty Ag
Trailers, Harvester, Sprayer, Skid Loader, Silage
Bagger, Slurry Wagons, Grain Cart
Airport Support
Pushback Tractor, Towing Tugs, Aircraft Tow
Tractor, Refueling Trucks, Food Service Trucks,
Baggage Tractors, De-Icing Equipment,
Runway Clearing Equipment
Construction
All-Terrain Crane, Rough Terrain Crane,
Excavator, Compactor, Wheel Loader, Road
Roller, Motor Grader, Articulated Dump Truck,
Rubber Tire Road Roller, Backhoe Loaders,
Haul Trucks, Scraper Rough Terrain Forklifts,
Trenchers, Drills
Forestry Logging Forwarder, Kidder, Loaders, Yard
Forklifts, Harvesters Fellers
Material Handling
Port Tractor, Rail Yard Spotter, Stevedoring
Tractor, Trailer Spotter, Yard Jockey, Scissor
Lift, Straddle Carrier, Manlift, Forklift, Boom Lift
Telebandlers, Aerial Work Platforms
Mining
Specialized Mining, Excavator, Haul Truck,
Underground Loader, Service Trucks, Wheel
Loaders, Scrapers, Load Haul Dumps,
Personnel Transports, Bolters, Scalers
Municipal
Street Sweeper, Utility Tractor, Utility Trucks,
Tree Trimmers, Dump Trucks, Tow Trucks, Flat
Bed Trucks, Winch Applications
Oil & Gas
Fracturing Trailer, Injecter Heads, Top Drives,
Jack/Lift Boats, Wireline Trucks, Load-On /
Load-Off
Rail
Railcar Mover, Track Layers, Grinders, Platform
Crane, Locomotive Railcars, Ballast Equipment,
Winch Applications
954
AGENDA ITEM NO. 28.

ABS, ELECTRONIC STABILITY CONTROL (ESC),
ROLL STABILITY CONTROL (RSC), OPTIRIDE®,
ONGUARD® AND ONLANE®, COLLECTIVELY
“ELECTRONICS”
Failure of electronic components due to overvoltage
condition, improper grounding, electrostatic discharge
(ESD), improper shielding, electromagnetic interference (EMI), or other wiring or installation issues. Malfunctions and failure codes caused by other electronic subsystem failures (data bus, engine, transmission, dashboard, etc.)

HYDRAULIC COMPONENTS
For certain components, brake fluid DOT3 or DOT4 is
used as the operating medium. Use of any other fluid will void all warranties associated with that component. For hydraulic braking applications the brake fluid is considered a maintenance item. Maintenance intervals are listed in TB- 1367.

COVERAGE LIMITATIONS

PRODUCT DESCRIPTION

ALL PRODUCTS
Any claim beyond 60 days from date of repair will not be accepted or honored under this warranty program.

Products purchased on an incomplete vehicle (glider) are limited to one year, 1/Unl/P .

For vehicles that operate full- or part-time outside of the United States and Canada, a 1-Year/Unlimited Miles parts only (1/Unl/P) will apply.

TOOLBOX PLUS™ DIAGNOSTIC SOFTWARE
Proper diagnostics of WABCO Electronics may require the latest version of TOOLBOX PLUS™. Additional labor due
to use of an outdated version of TOOLBOX™ software
and/or the time to purchase or install the latest version of TOOLBOX PLUS™ are not covered under product
warranty.

TERMS AND CONDITIONS

COVERAGE EXCLUSIONS

PRODUCT DESCRIPTION

ALL PRODUCTS
This Warranty shall not apply to the following, but not limited to: (1) damage to the product or its component
parts caused by incorrect use, installation, maintenance or repair, including without limitation (a) improper fit of mating components or brackets, damaged threads, cut, broken,
chafed, pinched or otherwise damaged wiring (sensors,
harnesses and connectors), (b) sensors damaged during
removal when seized in block, or associated with sensor adjustments/ alignments, and (c) damage resulting from the use or installation of non-genuine WABCO components or
materials; (2) damage to the product, its component parts, or diminished product or component part performance due to incorrect operation, deviation from approved conditions or misapplication; (3) any unauthorized disassembly of the product or its component parts including without limitation (a) obliterated, defaced or missing WABCO or WABCO
name plate, serial numbers or label identifying the device as
a ZF product or WABCO component, (b) changes to sealed
adjusting screws, and (c) opening or attempted repair of non-serviceable components; (4) malfunction
of the component d ue to internal cont amination of t he vehicle system including without limitation (a) water and other contamination damage that is due to the use of a
non-genuine air dryer cartridge or (b) valve failures due to contamination in air system, (5) complaints associated
with noise, (6) damage resulting from corrosion (including oxidation of electrical devices and connections).

AIR DRYERS
Mounting brackets (see vehicle OEM). Desiccant cartridge housing only.

AIR SYSTEM COMPONENTS
Normal wear items; Gladhand seals, dash valve knobs,
valve actuation handles, treadles, pedals.
955
AGENDA ITEM NO. 28.

WARRANTY - MODEL YEAR 2021 VEHICLES
(1) What is Covered by this Commercial Warranty?
ZF CV Systems North America LLC and its North American
subsidiaries and affiliates (ZF) warrant to the owner (“Owner”) that the components listed in this publication, which have been installed by an Original Equipment Manufacturer (“OEM”) as original equipment will be free from defects in material and workmanship. This warranty coverage begins from the original in-service date to the limits provided and runs concurrently with any warranties provided by OEMs and/or any distribution agreements and/or any service contracts that cover the components listed in this publication, if any. If the components listed in this publication are covered by an OEM warranty and/or service contract, then the OEM’s warranty and/ or service contract shall supersede ZF’s warranty and Owner shall comply with all OEM’s warranty and/or service contract requirements for claims under such OEM’s warranty and/or service contract until those agreements expire.

Once those agreements expire and provided the ZF warranty has not expired under the terms stated above, the ZF warranty will be in effect until its expiration date.

Warranty coverage ends at the expiration of the applicable time period from the date of vehicle purchase by the first Owner, or, the applicable mileage limitation, whichever occurs first. Duration of coverage varies by component and vocation as detailed previously in this publication.

Some components are warranted for parts only and the Owner must pay any labor costs associated with the repair or replacement of the component. Other components are warranted for both parts and reasonable labor to repair or replace the subject component.

Additional diagnostic time due to use of an outdated version of TOOLBOX™, time to purchase or install latest version of TOOLBOX™ are the responsibility of the authorized ZF distributor networks and are not covered under product warranty. Components installed as replacements under this warranty are warranted only for the remainder of the original period of time or mileage under the original warranty. (2) Designation of Vocational Use Required. To obtain warranty coverage, each Owner must notify ZF through the OEM new truck and/or trailer dealer of the intended vocational use of the vehicle into which the WABCO components have been incorporated prior to the vehicle in- service date. This notification may be accomplished by registering the vehicle through your OEM new truck and/or trailer dealer or with ZF directly. Failure to notify ZF of (I) the intended vocational use of the vehicle or (II) a change in vocational use from that which was originally designated, will result in the application of a one year, unlimited mileage, parts only warranty (1/Unl/P) from the initial in- service date. A second Owner and each subsequent Owner
must
also notify ZF as to the intended vocational use of the vehicle. This notification can be sent directly to ZF or through
the OEM new truck and/or trailer dealer. The duration and mileage coverage of this warranty cannot exceed the coverage extended to the first Owner after his or her initial designation of vocational use. Coverage under ZF’
s warranty requires that the application of
products be properly approved pursuant to OEM and ZF, approvals. (3) What is the Cost of this Warranty? There is no charge to the Owner for this warranty.
(4) What is not Covered by this Warranty? In addition to the items listed on "Coverage Exclusions," this warranty does not cover normal wear and tear, or service items; nor does it cover a component that fails, malfunctions or is damaged as a result of (a) improper handling, storage, installation, adjustment, repair or modification including the use of unauthorized attachments or changes or modification in the vehicle’s configuration, usage, or vocation from that which was originally approved by ZF, (b) accident, fire or other casualty, natural disaster, road debris, negligence, misuse, abuse, or improper use (including loading beyond the specified maximum vehicle weight or altering engine power settings to exceed the brake system capacity),
or (c) improper or insufficient maintenance (including deviation from maintenance intervals, approved lubricants, or lube levels). This warranty does not cover any component or part that is not sold by ZF. (5) To obtain service. If the owner discovers within the applicable coverage period a defect in material or workmanship, the Owner must promptly give notice to either ZF or the dealer from which the vehicle was purchased. To obtain service, the vehicle must be taken to any participating OEM dealer or ZF distributor networks' servicer. The dealer or ZF authorized servicer will inspect the vehicle and contact ZF for an evaluation of the claim. When authorized by ZF, the dealer or ZF authorized servicer will repair or replace during the term of this warranty any defective WABCO component covered by this warranty. (6) Disclaimer of Warranty and Limitation of remedies. TO THE MAXIMUM

EXTENT PERMITTED BY LAW, THE LIMITED WARRANTY SET

FORTH HEREIN IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER

WARRANTIES, EXPRESS OR IMPLIED, ARISING BY OPERATION OF

LAW OR OTHERWISE, INCLUDING, WITHOUT LIMITATION, ANY

IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE AND/OR WARRANTY FOR HIDDEN OR

LATENT DEFECTS, AND IN NO EVENT WILL ZF OR ANY OF ITS

AFFILIATES BE LIABLE FOR DIRECT, INDIRECT, INCIDENTAL,

PROGRESSIVE, SPECIAL, OR CONSEQUENTIAL DAMAGES OF ANY
KIND.

TERMS AND CONDITIONS
956
AGENDA ITEM NO. 28.
(7) Legal action. Any legal action or claim arising from or related to this Warranty, in contract or otherwise, must be commenced within one year from the accrual of that cause of action, or be barred forever. Any dispute arising in connection with this agreement shall be governed by and construed according to the laws of the State of Michigan and be brought, heard and determined exclusively in either the Circuit Court for the County of Oakland, State of Michigan or the United States District Court for the Eastern District of Michigan. The parties stipulate that the referenced venues are convenient.
(8) Remedy. The exclusive remedy under this warranty shall be the repair or replacement of the defective component at ZF's option. ZF reserves the right to require that all applicable covered components are available and/or returned to ZF
for review
and evaluation. THE MAXIMUM LIABILITY, IF ANY, OF ZF FOR ALL

DAMAGES, INCLUDING WITHOUT LIMITATION CONTRACT

DAMAGES, BREACH OF WARRANTY, NEGLIGENCE, STRICT

LIABILITY, OR OTHER TORT, IS LIMITED TO AN AMOUNT NOT TO EXCEED THE PURCHASE PRICE OF THE PRODUCT and where
indicated in the product and application warranty information above, the inclusion of labor is limited to the standard repair time. THE

PARTIES ACKNOWLEDGE AND AGREE THAT THE LIMITATION

OF DAMAGES PROVISION SET FORTH IN THIS PARAGRAPH

SURVIVES BETWEEN THE ORIGINAL END USER AND ZF EVEN IF

THE EXCLUSIVE REMEDY SET FORTH ABOVE IS DEEMED TO FAIL
OF ITS ESSENTIAL PURPOSE. ZF may change the design or make improvements to its Products without incurring any warranty obligation for previously manufactured Product .
(9) Entire Agreement. This is the entire agreement between ZF and the Owner about warranty and no, ZF employee, or dealer is authorized to make any additional warranty on behalf of ZF unless in writing and signed by an authorized representative of ZF.
957
AGENDA ITEM NO. 28.

About ZF Friedrichshafen AG
ZF is a global technology company and supplies systems for passenger cars, commercial vehicles and industrial technology, enabling the next generation of mobility. ZF allows vehicles to see, think and act. In the four technology domains Vehicle Motion Control, Integrated Safety, Automated Driving, and Electric Mobility, ZF offers comprehensive solutions for established vehicle manufacturers and newly emerging transport and mobility service providers. ZF electrifies different kinds of vehicles. With its products, the company contributes to reducing emissions and protecting the climate.

ZF, which acquired WABCO Holdings Inc. on May 29, 2020, now has 160,000 employees worldwide with approximately 260 locations in 41 countries. In 2019, the two then-independent companies achieved sales of €36.5 billion (ZF) and $3.4 billion (WABCO). For more information, visit: www.wabco-na.com
© 2021
ZF CV Systems North America LLC - All rights reserved - SP1375 / 2.2021 For further product details contact your distributor or the WABCO Customer Care Center at 855-228-3203.
958
AGENDA ITEM NO. 28.

Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 2/8/2010 WA0012

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.

This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This warranty applies only to the cab tubular support and mounting structures and other structural components of the cab of the vehicle model, as identified in the Pierce
specifications for the Fire and Rescue Apparatus.

This warranty does not apply to damage caused by corrosion.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4
Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

Fire and Rescue Apparatus
Coverage:

Ten (10) Year Structural Integrity
Custom Cab
Ten (10) Years
- or -
100,000 Miles
Warranty Period
Ends After:

The date of the original purchase invoice (issued when the product ships from the factory).Warranty Begins:

The Pierce Custom Cab shall be free from structural failures caused by defects in material and workmanship
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.

Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.

3. BUYER'S EXCLUSIVE REMEDY.
959
AGENDA ITEM NO. 28.

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.

Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.

3. BUYER'S EXCLUSIVE REMEDY.

Fire and Rescue Apparatus
Coverage:

Ten (10) Year Pro-Rated Paint and Corrosion
Cab
Ten (10) YearsWarranty Period
Ends After:

The date of the original purchase invoice (issued when the product ships from the factory).Warranty Begins:

Exterior surfaces of the cab painted by Pierce shall be free from blistering, peeling, corrosion or any other adhesion defect caused by defective manufacturing methods or paint material selection.
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 2/8/2010 WA0055

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.

This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This limited warranty is applicable to the vehicle in the following percentage costs of warranty repair, if any:

Topcoat Durability & Appearance: Gloss, Color Retention & Cracking
0-72 months 100%
73-96 months 50%
97-120 months 25%
Integrity of Coating System: Adhesion, Blistering/Bubbling 0-36 months 100%
37-84 months 50%
85-120 months 25%
Corrosion: Dissimilar Metal and Crevice
0-36 months 100%
37-48 months 50%
49-72 months 25%
73-120 months 10%
Corrosion Perforation
0-120 months 100%
This limited warranty applies only to exterior paint. Paint on the vehicle's interior is warranted only under the Pierce Basic One Year Limited Warranty.

Items not covered by this warranty include:
(a) Damage from lack of maintenance and cleaning (proper cleaning and maintenance procedures are detailed in the Pierce operation and maintenance manual).
(b) UV paint fade.
(c) Any cab not manufactured by Pierce.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4
960
AGENDA ITEM NO. 28.

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.

Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.

3. BUYER'S EXCLUSIVE REMEDY.

Fire and Rescue Apparatus
Coverage:

Two (2) Year Material and Workmanship
Power Step
Two (2) YearsWarranty Period
Ends After:

The date of the original purchase invoice (issued when the product ships from the factory).Warranty Begins:

Each power step shall be free from defects in material and workmanship
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 2/8/2010 WA0031

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.

This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

No specific exclusions apply
Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4
961
AGENDA ITEM NO. 28.

Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 2/8/2010 WA0014

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.

This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This limited warranty applies to all of the control modules for the Command Zone system, including the full color graphic displays. Related wire harnesses, cables and connectors are not covered under this limited warranty and are instead covered under the Pierce One Year Basic Apparatus Limited Warranty.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4
Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

Fire and Rescue Apparatus
Coverage:

Five (5) Year Material and Workmanship
Command Zone Electronics
Five (5) YearsWarranty Period
Ends After:

The date of the original purchase invoice (issued when the product ships from the factory).Warranty Begins:

Command Zone control modules shall be free from failures caused by defects in material and workmanship
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.

Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.

3. BUYER'S EXCLUSIVE REMEDY.
962
AGENDA ITEM NO. 28.

Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 1/11/2011 WA0188

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.

This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This limited warranty does not apply to related wire
harnesses, cables, and connectors, which are covered by the Pierce one (1) year basic apparatus limited warranty.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4
Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

Fire and Rescue Apparatus
Coverage:
54 Months Material and Workmanship
Camera System
Fifty - Four (54) monthsWarranty Period
Ends After:

The date of delivery.Warranty Begins:

This limited warranty covers repairs to correct any defect related to materials or workmanship of the Sharpvision
camera system installed on the apparatus occuring during th e
warranty period.
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.

Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.

3. BUYER'S EXCLUSIVE REMEDY.
963
AGENDA ITEM NO. 28.

NEW PRODUCT WARRANTY

PARTICIPATING OEM SALES

DISTRIBUTOR SALES

LIMITED WARRANTY ON NEW ALLISON AUTOMATIC TRANSMISSIONS

USED IN EMERGENCY VEHICLE APPLICATIONS

Allison Transmission will provide for repairs or replacement, at its option, during the warranty period of each new Allison transmission listed below that is installed in an Emergency Vehicle in accordance with the following te rms, conditions, and limitations.

WHAT IS COVERED
 WARRANTY APPLIES — This warranty is for new Allison transmission models listed below installed in an Emergency Vehicle and is provided to the original and any subsequent owner(s) of the vehicle during the warranty period.  REPAIRS COVERED — The warranty covers repairs or replacement, at Allison Transmission’s option, to correct any transmission malfunction resulting from defects in material or workmanship occurring during the warranty period. Needed repairs or replacements will be performed using the method Allison Transmission determines most appropriate under the circumstances.  TOWING — Towing is covered to the nearest Allison Transmission Distributor or authorized Dealer only when necessary to prevent further damage to your transmission.
 PAYMENT TERMS — Warranty repairs, including parts and labor, will be covered per the schedule shown in the chart contained in section “APPLICABLE MODELS, WARRANTY LIMITATIONS, AND ADJUSTMENT SCHEDULE.”  OBTAINING REPAIRS — To obtain warranty repairs, take the vehicle to any Allison Transmission Distributor or authorized Dealer within a reasonable amount of time and request the needed repairs. A reasonable amount of time must be allowed for the Distributor or Dealer to perform necessary repairs.
 TRANSMISSION REMOVAL AND REINSTALLATION — Labor costs for the removal and re-installation of the transmission, when necessary to make a warranty repair, are covered by this warranty.  WARRANTY PERIOD — The warranty period for all coverages shall begin on the date the transmission is delivered to the first retail purchaser, with the following exception:

Demonstration Service - A transmission in a new truck or bus may be demonstrated to a total of 5000 miles (8000 kilometers).

If the vehicle is within this limit when sold to a retail purchaser, the warranty start date is the date of purchase. Normal warranty services are applicable to the demonstrating Dealer. Should the truck or bus be sold to a retail purchaser after these limits are reached, the warranty period will begin on the date the vehicle was first placed in demonstration service and the purchaser will be entitled to the remaining warranty.

APPLICABLE MODELS, WARRANTY LIMITATIONS, AND ADJUSTMENT SCHEDULE

WARRANTY LIMITATIONS
(Whichever occurs first)

ADJUSTMENT CHARGE TO BE

PAID BY THE CUSTOMER APPLICABLE
MODELS
Months
Transmission Miles
Or Kilometers Parts Labor
MT, MD
3000, 3200, 3500, 3700 0–24 No Limit No Charge No Charge HT with Hydraulic Controls 0–24 No Limit No Charge No Charge AT, 1000 Series, 2000 Series,
2400 Series 0–36 No Limit No Charge No Charge
HT with Electronic Controls 0–60 No Limit No Charge No Charge HD
1000 EVS, 2100 EVS, 2200 EVS
2350 EVS, 2500 EVS, 2550 EVS,
3000 EVS, 3500 EVS, 4000,
4000 EVS, 4500, 4500 EVS, 4700,
4700 EVS, 4800, 4800 EVS
0–60 No Limit No Charge No Charge

964
AGENDA ITEM NO. 28.

WHAT IS NOT COVERED
 DAMAGE DUE TO ACCIDENT, MISUSE, or ALTERATION — Defects and damage caused as the result of any of the following are not covered:
— Flood, collision, fire, theft, freezing, vandalism, riot, explosion, or objects striking the vehicle; — Misuse of the vehicle;
— Installation into unapproved a pplications and installations; — Alterations or modification of th e transmission or the vehicle, and — Damage resulting from improper storage (refer to long-term st orage procedure outlined in the applicable Allison Service Manual) — Anything other than defects in Allison Transmission material or workmanship NOTE: This warranty is void on transmissions used in vehicles currently or previously titled as salvaged, scrapped, junked, or totale d.  CHASSIS, BODY, and COMPONENTS — The chassis and body company (assemblers) and other component and equipment manufacturers are solely responsible for warranties on the chassis, body, component(s), and equipment they provide. Any transmission repair caused by an alteration(s) made to the Allison transmission or the vehicle which allows the transmission to be installed or operated outside of the limits defined in the appropriate Allison Installation Guideline is solely the responsibility of the entity making the alteration(s).  DAMAGE CAUSED by LACK of MAINTENANCE or by th e USE of TRANSMISSION FLUIDS NOT RECOMMENDED in the OPERATOR’S MANUAL — Defects and damage caused by any of the following are not covered:
— Failure to follow the recommendations of the maintena nce schedule intervals applicable to the transmission; — Failure to use transmission fluids or maintain transm ission fluid levels recommended in the Operator’s Manual.  MAINTENANCE — Normal maintenance (such as replacement of filters, screens, and transmission fluid) is not covered and is the owner’s responsibility.
 REPAIRS by UNAUTHORIZED DEALERS — Defects and damage caused by a service outlet that is not an authorized Allison Transmission Distributor or Dealer are not covered.
 USE of OTHER THAN GENUINE ALLISON TRANSMISSION PARTS — Defects and damage caused by the use of parts that are not genuine Allison Transmission parts are not covered.  EXTRA EXPENSES — Economic loss and extra expenses are not covered. Examples include but are not limited to: loss of vehicle use; inconvenience; storage; payment for loss of time or pay; vehicle rental expense; lodging; meals; or other travel costs.  “DENIED PARTY” OWNERSHIP — Warranty repair parts and labor costs are not reimbursed to any participating or non-participating OEMs, dealers or distributors who perform warranty work for, or on behalf of, end users identified by the United States as being a “denied party” or who are citizens of sanctioned or embargoed countries as defined by the U.S. Department of Treasury Office of Foreign Assets Control. Furthermore, warranty reimbursements are not guaranteed if the reimbursement would be contrary to any United States export control laws or regulations as defined by the U.S. Department of Commerce, the U.S. Department of State, or the U.S. Department of Treasury.

OTHER TERMS APPLICABLE TO CONSUMERS AS DEFINED by the MAGNUSON-MOSS WARRANTY ACT This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

Allison Transmission does not authorize any person to create for it any other obligation or liability in connection with these transmissions.

ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE APPLICABLE TO THESE TRANSMISSIONS IS LIMITED IN DURATION TO THE DURATION OF THIS WRITTEN WARRANTY.

PERFORMANCE OF REPAIRS AND NEEDED ADJUSTMENTS IS THE EXCLUSIVE REMEDY UNDER THIS WRITTEN WARRANTY OR ANY IMPLIED WARRANTY. ALLISON TRANSMISSION SHALL NOT BE LIABLE FOR INCIDENTAL OR

CONSEQUENTIAL DAMAGES (SUCH AS, BUT NOT LIMITED TO, LOST WAGES OR VEHICLE RENTAL EXPENSES) RESULTING FROM BREACH OF THIS WRITTEN WARRANTY OR ANY IMPLIED WARRANTY.** ** Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you.

OTHER TERMS APPLICABLE TO OTHER END-USERS

THIS WARRANTY IS THE ONLY WARRANTY APPLICABLE TO THE ALLISON TRANSMISSION MODELS LISTED

ABOVE AND IS EXPRESSLY IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. ALLISON

TRANSMISSION DOES NOT AUTHORIZE ANY PERSON TO CREATE FOR IT ANY OTHER OBLIGATION OR LIABILITY IN CONNECTION WITH SUCH TRANSMISSIONS. ALLISON TRANSMISSION SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM BREACH OF THIS WARRANTY OR ANY IMPLIED WARRANTY.

QUESTIONS
If you have any questions regarding this warranty or the performance of warranty obligations, you may contact any Allison Transmission Distributor or Dealer or write to:

Allison Transmission, Inc.

P.O. Box 894
Indianapolis, IN 46206-0894
Attention: Warranty Administration PF-9

Form SE0616EN (201009)

965
AGENDA ITEM NO. 28.

Warranty Begins:

The transmission cooler shall be free from component or structural failures caused by defects in material and/or workmanship. Collateral damage up to $10,000 per
occurrence is available for the first three (3) years.
(b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; (d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce.

Five (5) Years on Oil Cooler and three (3) years on collateral damage coverage
Warranty Period
Ends After:

Fire and Rescue Apparatus
Coverage:

Five (5) Year Material and Workmanship - Transmission Oil Cooler Three (3) Year Collateral Damage Coverage

1. LIMITED WARRANTY
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

The date of delivery to the first retail purchaser.

This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This warranty does not cover repair due to accidents,
misuse, and excessive vibration, flying debris, storage damage (freezing), negligence or modification. This warranty is void if any modification or repairs are performed without authorization. This also voids any future warranty.

This warranty does not cover cost of maintenance or repairs due to lack of required maintenance services as
recommended. Performance of the required maintenance
and use of proper fluids are the responsibility of the owner.

Towing is covered to the nearest distributor or authorized dealer only when necessary to prevent further damage to your transmission.

Labor costs for the removal and reinstallation of goods may be covered when necessary to make repairs. Please contact your OEM for authorization.

Replacement of cooler during the warranty period is limited to 100% of reasonable labor costs up to a maximum of $700 to remove, replace, or repair the oil cooler.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE
POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.

Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.

3. BUYER'S EXCLUSIVE REMEDY.

Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle.
2/22/2012 WA0216
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES

ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

2. DISCLAIMERS OF WARRANTIES
capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty. 966
AGENDA ITEM NO. 28.

Limited Lifetime Warranty
Effective as of January 1, 2024

1. General. United Plastic Fabricating, Inc. (the
"Company") warrants to the owner (the “Owner”) that
the products set forth on Exhibit A, attached hereto (the "Product") will be reasonably free from defects in
materials and workmanship for the service life of the
Product. This Limited Lifetime Warranty (the
“Warranty”) only applies to Company Products that are:
(a) owned by a federal, state, county or local
government, a volunteer fire department or dedicated
commercial fire service operation; (b) continuously and actively used in emergency response and/or fire
suppression vehicles; and (c) used, stored, handled
and installed in the manner recommended by
Company.

2. Warranty Obligations. Subject to the exclusions and
limitations set forth in this Warranty, Company will, at its option, repair or offer a one (1) time replacement of the Product without charge, if the Product fails or does not perform as warranted during the warranty period due to
a manufacturing defect or a defect in materials. Repair or replacement shall include reasonable labor charges
necessary to repair or replace the defective Product but shall not include: (a) the costs associated with removal of the Product from the vehicle or the cost to otherwise provide access to the Product in the vehicle; (b) the cost associated with any required upgrades the vehicle
(including, without limitation, upgrades required to
strengthen the vehicle’s frame); or (c) travel costs,
except as provided by Section 3. Company's obligation
as to repair or replacement shall further be limited to repair or replacement with the models of the Product
that are available at the time of the repair or
replacement, and shall be limited to the repair or
replacement of only the specific Product that fails due to a manufacturing defect. In the event a Product
becomes unavailable or cannot be supplied by
Company for any reason a substitute Product of equal
quality and functionality of the subject Product may be substituted by Company. Any repaired Product shall
remain subject to this Warranty and any repair shall not extend the warranty period in any manner or start a new warranty period. Any Product that is replaced by
Company shall be excluded from this Warranty. In no
event shall Company be required to expend, in any one
(1) or series of expenditures, more than the purchase
price of the Product to repair or replace a defective
Product. Amounts expended by Company shall include
all amounts paid by Company in connection the repair
or replacement, including without limitation, amounts
paid to third-parties, material costs, incidental costs and travel costs (except as provided by Section 3).

3. Travel; Expenses; Product Access. Company shall
be responsible for any travel costs incurred to repair or replace the Product provided that: (a) the Product is
located in the continental United States or Canada; and (ii) the warranty claim is initiated prior to the date on which NFPA 1912 Standards (Annex D) recommends
replacement of the Product. All other travel costs
incurred by Company or its agents to repair or replace
the Product shall be the responsibility of the party
asserting the warranty claim. Company reserves the
right to require, as a condition to undertaking any repair or replacement: (y) pre-payment of its anticipated travel costs; and (z) satisfactory arraignments concerning
scheduling and access to the Product. If the subject
Product is located in an area of the world considered, in Company’s sole discretion, to be unsafe Company may
refuse to process the claim or require relocation of the Product, at no expense to Company, to an area where
such repairs can be performed safely by Company or
its agents. In the event Company or Company’s agents
are dispatched to repair or replace a defective Product and the vehicle in which the Product has been installed is not available or the Product is not readily accessible, for any reason, Company or Company’s agents, as the
case may be, shall be immediately reimbursed for all
expenses incurred therewith.

4. Exclusions: Products must be stored, handled,
installed, used and maintained in accordance with
instructions provided by Company, and this Warranty is
conditioned upon compliance with all such instructions.

This Warranty does not cover defects caused by: (a)
improper installation; (b) modification, alteration or
repair of the Product by any unauthorized third-party;
(c) misuse, including, without limitation, improper
967
AGENDA ITEM NO. 28.

storage or handling of the Product (e.g. excessive
exposure to UV rays); chemical abuse (e.g. harsh
cleansers and solvents), thermal abuse or shock (e.g.
excessive heat or cold); (d) damage not resulting from
manufacturing defects that occur while the Product is
not in Company’s possession (e.g. accidents); or (e)
unreasonable or unintended use of the Product. Copies
of the Company's operation and maintenance
instructions are available on the Company's website
https://www.unitedplastic.com/upf-documents/

5. Disclaimer. THE WARRANTIES SET FORTH

HEREIN ARE THE ONLY WARRANTIES MADE BY
COMPANY IN CONNECTION WITH THE PRODUCT.

COMPANY CAN NOT AND DOES NOT MAKE ANY

IMPLIED OR EXPRESS WARRANTIES WITH

RESPECT TO THE PRODUCT, AND DISCLAIMS ALL

OTHER WARRANTIES, INCLUDING, BUT NOT

LIMITED TO, ANY WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. PRODUCTS SOLD BY

COMPANY ARE SOLD ONLY TO THE

SPECIFICATIONS SPECIFICALLY SET FORTH BY
COMPANY IN WRITING. OTHER THAN THE LIMITED

WARRANTY SET FORTH HEREIN, COMPANY

MAKES NO OTHER WARRANTIES, EXPRESS OR
IMPLIED. COMPANY'S SOLE OBLIGATION UNDER

THIS WARRANTY SHALL BE REPAIR OR
REPLACEMENT OF NON-CONFORMING PRODUCT.

BUYER ASSUMES ALL RISK WHATSOEVER AS TO

THE RESULT OF THE USE OF THE PRODUCT

PURCHASED, WHETHER USED SINGULARLY OR IN

COMBINATION WITH ANY OTHER PRODUCTS OR
SUBSTANCES.

6. Limitation of Liability. NO CLAIM BY OWNER OF

ANY KIND, INCLUDING CLAIMS FOR

INDEMNIFICATION, SHALL BE GREATER IN

AMOUNT THAN THE PURCHASE PRICE OF THE

PRODUCT IN RESPECT TO WHICH DAMAGES ARE
CLAIMED. IN NO EVENT SHALL COMPANY BE

LIABLE TO OWNER IN TORT, CONTRACT OR

OTHERWISE, FOR ANY SPECIAL, INDIRECT,

INCIDENTAL, CONSEQUENTIAL (INCLUDING,

WITHOUT LIMITATION, ANY OBLIGATION OF

COMPANY TO REPAIR OR REPLACE ANY

CHASSIS, SUB-FRAMES, BODIES, VALVES,

DUMPS, HOSES, PRESSURE VACUUM VENTS OR

OTHER SIMILAR COMPONENTS), RELIANCE,

STATUTORY, SPECIAL, PUNITIVE OR EXEMPLARY

DAMAGES, INCLUDING, BUT NOT LIMITED TO,

LOST PROFITS, LOSS OF USE, LOSS OF TIME,

LOSS OF REVENUES, INCONVENIENCE, LOSS

BUSINESS OPPORTUNITIES, OR DAMAGE TO

GOOD WILL OR REPUTATION, EVEN IF ADVISED

OF THE POSSIBILITY OF SUCH DAMAGES OR

SUCH DAMAGES COULD HAVE BEEN

REASONABLY FORESEEN, IN CONNECTION WITH,

ARISING OUT OF, OR AS A RESULT OF, THE SALE,

DELIVERY, SERVICING, USE OR LOSS OF USE OF

THE PRODUCTS SOLD HEREUNDER, OR FOR ANY

LIABILITY OF BUYER TO ANY THIRD PARTY WITH
RESPECT THERETO.

7. Reformation. If any term or provision of this Warranty shall be held or deemed to be, or shall in fact be, invalid, inoperative, illegal or unenforceable as applied in any case or in any jurisdiction or jurisdictions because of the conflicting nature of any provision with any constitution or statute or rule of public policy or for any other reason, then: (a) such circumstance shall not have the effect of rendering the provision or provisions in question invalid, inoperative, illegal or unenforceable in any other
jurisdiction or in any other case or circumstance or of rendering any other provision or provisions herein
contained invalid, inoperative, illegal or unenforceable to the extent that such other provisions are not
themselves actually in conflict with such constitution, statute or rule of public policy; and (b) any such
invalid, inoperative, illegal or unenforceable provision shall be reformed and construed in any such jurisdiction or case so that such provision would be valid, operative and enforceable to the maximum extent permitted in
such jurisdiction or case.

8. Headings. The headings contained herein are for
convenience and reference only, and shall be given no
effect in the interpretation of any term or condition of this Warranty.

9. Submitting a Warranty Claim. To request coverage
under this Warranty you must submit a claim through
Company’s_website:
https://www.unitedplastic.com/contact/product-support/

10. Transferability. This Warranty is transferable and
entitles the transferee to coverage for the remainder of the original warranty period.

11. Modification. This Warranty may be modified (a) as set forth on a binding sales order for the Product or (b) by a written agreement between Company and the
Owner.
968
AGENDA ITEM NO. 28.

Exhibit A

Covered Product List
 Poly-Tanks®
 PolySide® Wetside Tanks
 Defender™ Skid Tanks
 Ellip-T™ Elliptical Tanks
 ARFF Tanks
969
AGENDA ITEM NO. 28.

Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 2/8/2010 WA0009

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.

This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This warranty applies only to the body tubular support and mounting structures and other structural components of the body of the vehicle model, as identified in the Pierce
specifications for the Fire and Rescue Apparatus.

This warranty does not apply to damage caused by corrosion.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4
Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

Fire and Rescue Apparatus
Coverage:

Ten (10) Year Structural Integrity
Apparatus Body
Ten (10) Years
- or -
100,000 Miles
Warranty Period
Ends After:

The date of the original purchase invoice (issued when the product ships from the factory).Warranty Begins:

The apparatus body shall be free from structural failures caused by defects in material and workmanship
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.

Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.

3. BUYER'S EXCLUSIVE REMEDY.
970
AGENDA ITEM NO. 28.

Effective March 15, 2010

AMDOR Inc. TERMS OF BUSINESS AND GENERAL INFORMATION

Warranty:

All AMDOR Inc. roll-up door products are warr anted for a period of 10 years from the date of delivery (with the exception of wet paint adhesion - please see below). AMDOR Inc. liability covers the replacement or repai r of any component that fails due to defects in material and / or workmanship during the coverage period. We accept no liability for claims made for damages to any part (or parts ) of a vehicle and / or machine (of any type) or injury claims by a person or persons assumed or alleged to have been brought about by the use or misuse of any product supplied by AMDOR Inc. Warranty coverage does not extend to door atta chments including (but not lim ited to) decals, emblems, stripes and adhesives.

In order to initiate the claims process pl ease contact your authoriz ed representative of AMDOR Inc. Warranty claims must be acco mpanied by a written description providing full and reasonable details as to the nature of the defect. Upon receipt of your claim arrangements will be made to inspect the defective produc t (if necessary). Justified warranty claims will be repair ed, exchanged, or credited to the customer's account at AMDOR Inc.'s discretion. All warranty claims must be approved in writing by the Customer Service Manager for AMDOR Inc. There are no exceptions to this clause.

Limited warranty coverage in cludes the labor associated with the disassembly and assembly of products deemed to be defective by AMDOR Inc. Labor allowances are based on a set time schedule as determined by AMDOR Inc. The maximum allowable hourly labor rate is $ 50. A ll warranty labor claims must be approved in writing by an authorized representative of AMDOR Inc. prior to commenc ement of work. Allowances for removal and installation:

Curtain replacement: 3/4 hour
Balancer replacement: 1 hour
Door ajar switch 3/4 hour
Bottom Panel Assembly: 1/2 hour
Slat replacement: 3/4 hour
Door removal and replacement 1 1/2 hours

Items authorized for return must be acco mpanied by a Return Goods Authorization (RGA) number. We will accept collect sh ipments of items de emed to be defective provided that they are returned via the mo st economical carrier. Should items be 971
AGENDA ITEM NO. 28.
returned by means other than the most economical carrier the difference will be charged back to the sender.

AMDOR Inc. reserves the right to reject any claim when a product has been opened, interfered with or modified. Claims may also be rejected when damage to the product (or any sub-assembly) has been brought about by accident, misuse, abuse, vandalism, incorrect installation, temperature extremes, chemical exposure or any factor other than regular operating conditions.

Limited Wet Paint Match Adhesion Warranty

AMDOR Inc. warrants wet paint finishes applied by AMDOR utilizing our approved factory paint specification. All wet paint matc h colors must be approved in writing by an authorized OEM representative. AMDOR Inc. will provide a color spray out for this purpose. The time required for shipping and cons ideration of initial color spray outs will be considered over and above stated lead time s. Warranty coverage will extend for a period of not less than 5 years from the date of delivery as determined by AMDOR Inc.'s Packing Slip. AMDOR reserves the right to determine whether individual units will be replaced and / or repaired by an AMDOR approved vendor. An allowance will be made for labor associated with the disassembly and assembly of individual units at the prescribed hourly rate of $ 50 per hour. Compensation for labor will not exceed the maximum time allowance permitted for door removal and replacement. Written approval including specified allowance for time must be obtained from AMDOR prior to initiating work. Warranty coverage will ext end to the following visible paint system defects:

1./ Loss of mechanical adhesion as eviden ced by peeling, cr acking or blistering which exposes the substrate material.

2./ Corrosion of the substrat e due to paint system failure.

3./ Fading which results in a subs tantial departure from the primary AMDOR approved body color.

Wet paint adhesion limited warranty coverage will be excluded when damages to the system are determined by AMDOR Inc. to be a result of the following:

1./ Damage caused through the use of atta chments including (but not limited to) decals, labels, adhesives, non factory approved coatings.

2./ Loss of gloss, discoloration or damage due to improper maintenance (including but not limited to) mechanical wash systems, pressure washers, steam cleaners, non approved wash or polishing agents.

3./ Abuse, acts of nature, excessive heat / cold, chemical exposure, vandalism and / or accidents.

4./ Scratches, chips, abrasions, or dents from any source.

This document supercedes all previous written and / or verbal warranties provided by AMDOR Inc. and / or it's affiliates.
972
AGENDA ITEM NO. 28.

This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This limited warranty applies to the PUC Pump and all its components manufactured under the Pierce brand, including the integrated pump transmission. Items not manufactured under the Pierce brand such as valves, relief valves or wear items such as wear rings, seals, bearings or costs of
removal, transporting, storing, or reinstallation are not covered by this six-year limited warranty and are instead covered under the Pierce Basic One Year Limited Warranty.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.

Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.

3. BUYER'S EXCLUSIVE REMEDY.
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce.

Seven (7) Years
- or -
3000 Pump Hours
Warranty Period
Ends After:

Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 4/21/2022 WA0390
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.

Fire and Rescue Apparatus
Coverage:

Seven (7) Year Material and Workmanship
PUC-NG Pump
Limited Warranty
Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

The PUC-NG Pump, intergrated pump transmisison, and its components manufactured under the Pierce brand in its Fire and Rescue Apparatus vehicle shall be free from failures caused by defects in material and workmanship

1. LIMITED WARRANTY
(b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the purchaser who first puts the product in service ("Buyer"):
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; The date of the original purchase invoice (issued when the product ships from the factory).Warranty Begins:
973
AGENDA ITEM NO. 28.

Warranty Begins:

Stainless steel piping shall be free from structural failures caused by defects in material and workmanship, or
perforation caused by corrosion.
(b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; (d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce.

Ten (10) Years
- or -
100,000 Miles
Warranty Period
Ends After:

Fire and Rescue Apparatus
Coverage:

Ten (10) Year Material and Workmanship
Stainless Steel Piping

1. LIMITED WARRANTY
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

The date of the original purchase invoice (issued when the product ships from the factory).

This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

Pierce’s obligation under this warranty is limited to repairing or replacing without charge, as Pierce may elect, the
stainless steel piping or components which Pierce
determines to have failed due to defective material and workmanship, or perforation caused by corrosion.

This warranty does not cover the use of fluoroprotein (FP) type foam. The sodium chloride within FP foam can cause long-term damage to system components if not thoroughly flushed immediately after use.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE
POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.

Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.

3. BUYER'S EXCLUSIVE REMEDY.

Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle.
3/22/2012 WA0035
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES

ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

2. DISCLAIMERS OF WARRANTIES
capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty. 974
AGENDA ITEM NO. 28.

Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 2/8/2010 WA0057

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.

This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This limited warranty is applicable to the vehicle in the following percentage costs of warranty repair, if any:

Topcoat Durability & Appearance: Gloss, Color Retention & Cracking
0-72 months 100%
73-96 months 50%
97-120 months 25%
Integrity of Coating System: Adhesion, Blistering/Bubbling 0-36 months 100%
37-84 months 50%
85-120 months 25%
Corrosion: Dissimilar Metal and Crevice
0-36 months 100%
37-48 months 50%
49-72 months 25%
73-120 months 10%
Corrosion Perforation
0-120 months 100%
This limited warranty applies only to exterior paint. Paint on the vehicle's interior is warranted only under the Pierce Basic One Year Limited Warranty.

Items not covered by this warranty include:
(a) Damage from lack of maintenance and cleaning (proper cleaning and maintenance procedures are detailed in the Pierce operation and maintenance manual).
(b) UV paint fade.
(c) Any cab not manufactured by Pierce.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4
Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

Fire and Rescue Apparatus
Coverage:

Ten (10) Year Pro-Rated Paint and Corrosion
Custom Body
Ten (10) YearsWarranty Period
Ends After:

The date of the original purchase invoice (issued when the product ships from the factory).Warranty Begins:

Exterior surfaces of the body shall be free from blistering, peeling, corrosion or any other adhesion defect caused by defective manufacturing methods or paint material selection. (d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.

Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.

3. BUYER'S EXCLUSIVE REMEDY.
975
AGENDA ITEM NO. 28.

Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 2/22/2010 WA0018

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.

This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This warranty does not cover damage from lack of
maintenance and cleaning (proper cleaning and maintenance procedures are detailed in the Pierce operation and
maintenance manual).

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4
Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

Fire and Rescue Apparatus
Coverage:

Three (3) Year Material and Workmanship
Goldstar® Gold Leaf Lamination
Three (3) YearsWarranty Period
Ends After:

The date of the original purchase invoice (issued when the product ships from the factory).Warranty Begins:

Each Goldstar® gold leaf lamination shall be free from
defects in material and workmanship.
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.

Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.

3. BUYER'S EXCLUSIVE REMEDY.
976
AGENDA ITEM NO. 28.

JROGHQVWDWHĆUHFRP

DEALER SUPPLIED

PRODUCTS SERVICES
Exhibit “D”
5 AND
/OR
977
AGENDA ITEM NO. 28.
1 PROPOSAL INTRDUCTION
With over three decades of industry expertise, Golden State Fire Apparatus, Inc. (GSFA) proudly stands as the premier authorized dealership for top-tier fire apparatus in Central and Northern California. Our steadfast commitment to detail and customer satisfaction has earned us a trusted reputation among first responders.

We sincerely appreciate the opportunity to present this comprehensive proposal for a PIERCE MANUFACTURING, INC. VELOCITY PUC PUMPER. Your consideration of this proposal is greatly valued, and we are eager for the opportunity to support your department with the highest level of excellence and professionalism.

DEALER-SUPPLIED PRODUCTS AND SERVICES
Golden State Fire Apparatus Inc. (GSFA) will furnish the following items and/or services before final delivery so that all necessary components and support are in place, contributing to an efficient final delivery process. Please refer to the detailed list below for a comprehensive overview of the products and/or services included:

AUTHORIZED MANUFACTURER
In accordance with the State of California Vehicle Code, specifically Section 11701, it is mandated that "every manufacturer of a vehicle subject to registration shall make application to the Department of Motor Vehicles (DMV) for a license containing a general distinguishing number." The manufacturer, as of the proposal submission, holds a valid license in compliance with this requirement and is prepared to furnish a copy upon request. This adherence to regulatory standards ensures that the manufacturer maintains a current and official status, promoting transparency and compliance with legal requirements throughout the duration of the proposal and subsequent processes.

AUTHORIZED DEALERSHIP
In compliance with the State of California Vehicle Code, specifically Section 11701, it is mandated that "a dealer in vehicles of a type subject to registration shall make application to the Department of Motor Vehicles (DMV) for a license containing a general distinguishing number." Golden State Fire Apparatus, Inc. possesses a valid license at the time of the bid, as detailed above, and can promptly provide a copy upon request. This adherence to regulatory standards ensures that the dealership maintains a current and official status, promoting transparency and compliance with legal requirements throughout the duration of the proposal and subsequent processes.

AUTHORIZED SALES REPRESENTATIVE
In accordance with the State of California Vehicle Code, specifically Section 11800, it is expressly prohibited for any individual to function as a vehicle salesperson without obtaining a license issued by the Department of Motor Vehicles (DMV). The representative, at the time of 978
AGENDA ITEM NO. 28.
2 proposal, holds a valid vehicle salesperson's license and is ready to furnish a copy upon request.

This adherence to regulatory standards ensures that the sales representative maintains a current and official status, promoting transparency and compliance with legal requirements throughout the bidding process and subsequent phases.

VEHICLE REGISTRATION
In adherence to the State of California Vehicle Code Section 11739, it is mandated that the "dealer of a new motor vehicle sale is responsible for applying for the title, securing vehicle registration, and obtaining license plates for the Customer" through the Department of Motor Vehicles (DMV). Being a factory-authorized dealer of the vehicle being sold, Golden State Fire Apparatus, Inc. is duly authorized to register the vehicle with the State of California as a new vehicle manufacturer.

GSFA is committed to facilitating an excellent vehicle ownership experience for the customer.

As such, we will manage all necessary applications and complete all transfer papers, including the application for California Exempt "E" license plates. This approach ensures compliance with regulatory requirements and a hassle-free registration process for our valued customers.

WEEKLY PROGRESS PHOTOGRAPHS
GSFA is committed to ensuring transparency and comprehensive reporting throughout the construction process of the apparatus. To achieve this, GSFA will provide weekly photographs capturing various stages of the apparatus or major components under construction.

Commencing from the initiation of the manufacturing process, the photographic documentation will extend throughout the entire production phase by the manufacturer. These weekly reports will offer a visual representation of the ongoing progress of the apparatus, highlighting key milestones and showcasing unique features and aspects as construction unfolds.

Our focus is to provide customers with a clear and detailed insight into the evolution of the apparatus, fostering a deeper understanding of the craftsmanship and distinct elements incorporated during the construction process. This commitment to regular, visual updates aims to enhance communication and transparency regarding the progress of the apparatus.

CONTINGENCY RESERVE FUND
A Contingency Reserve Fund amounting to $25,000 per unit is incorporated into the quotation to address potential change orders, unforeseen items, or necessary work that may arise during the contract. The utilization of this reserve fund is at the sole discretion of the Customer. It is essential to note that this reserve fund is not an estimate for the aforementioned contingencies, and the actual costs associated with change orders, unforeseen items, or required work may surpass the reserved amount depending on their nature.

979
AGENDA ITEM NO. 28.
3 Any unused portion of the Contingency Reserve Fund will be credited back on the final invoice.

Alternatively, if not credited, the remaining funds will be promptly returned to the Customer in the form of a check following the completion of the final invoicing process. This approach guarantees financial transparency and effective management throughout the project.

COMMUNICATION EQUIPMENT MOUNTING FUND
A Communication Equipment Mounting Fund amounting to $2,500 per unit is incorporated into the quotation and is specifically designated to cover the expenses associated with mounting communication equipment, such as two-way radios, adhering to the directives of the Customer.

In the event that the mounting costs surpass the stipulated allowance, any additional work required can be undertaken at the prevailing shop rate. Any unused portion of the Communication Equipment Mounting Fund will be credited back on the final invoice.

Alternatively, if not credited, the remaining funds will be promptly returned to the Customer in the form of a check following the completion of the final invoicing process. This approach guarantees financial transparency and effective management throughout the project.

PRE-CONSTRUCTION, FACTORY VISIT
A pre-construction trip to the manufacturing facility is included for four (4) Customer representatives. The primary objective of review and finalize, in detail, the specifications prior to the start of production. The pre-construction trip is anticipated to span four (4) days and three (3) nights, with scheduling details collaboratively determined between GSFA and the Customer.

GSFA will cover the costs associated with airfare, lodging, meals, and ground transportation during the stay at the manufacturer's location. Air travel will be arranged from one of the following airports: Sacramento, San Francisco, or San Jose.

It is important to note that certain costs, including Customer ground transportation within California, airport parking, luggage fees, and incidental expenses during travel to the factory, fall within the responsibility of the Customer. Furthermore, flight reservations are non- refundable, and in the event of a cancellation post-booking, the Customer will bear all associated costs, encompassing not only the original ticket cost but also any change or cancellation fees levied by the airline and/or travel agency. Additionally, flight reservations are non-transferable. This delineation aims to establish clarity and transparency regarding the allocation of responsibilities and potential costs associated with the pre-construction trip.

FINAL INSPECTION, FACTORY VISIT
A final inspection trip to the manufacturing facility is included for four (4) Customer representatives. The primary objective of this visit is to ensure the adherence of the apparatus to specifications and promptly identify any potential deficiencies. The final inspection trip is 980
AGENDA ITEM NO. 28.
4 anticipated to span four (4) days and three (3) nights, with scheduling details collaboratively determined between GSFA and the Customer.

GSFA will cover the costs associated with airfare, lodging, meals, and ground transportation during the stay at the manufacturer's location. Air travel will be arranged from one of the following airports: Sacramento, San Francisco, or San Jose.

It is important to note that certain costs, including Customer ground transportation within California, airport parking, luggage fees, and incidental expenses during travel to the factory, fall within the responsibility of the Customer. Furthermore, flight reservations are non- refundable, and in the event of a cancellation post-booking, the Customer will bear all associated costs, encompassing not only the original ticket cost but also any change or cancellation fees levied by the airline and/or travel agency. Additionally, flight reservations are non-transferable. This delineation aims to establish clarity and transparency regarding the allocation of responsibilities and potential costs associated with the final inspection trip.

DELIVERY TO AUTHORIZED SERVICE FACILITY
GSFA will deliver the apparatus to our Northern California facility located in Sacramento for a comprehensive dealer preparation inspection. This service, conducted at the expense of GSFA, aims to have the apparatus in optimal condition at the time of final delivery.

To ensure the proper break-in of all components while still under warranty, the apparatus will be delivered under its own power. The use of rail or truck freight for transportation is deemed unacceptable in order to uphold the highest standards of quality assurance during the delivery process. This approach not only aligns with warranty considerations but also emphasizes the commitment to delivering a fully operational apparatus to our valued customers.

PRE-DELIVERY SERVICE
Before reaching its final destination, the apparatus undergoes a pre-delivery service conducted by Golden State Emergency Vehicle Service, Inc. This service is designed to tap into the expertise of an external source, providing an experienced perspective that enhances the thoroughness of your final inspection. Our pre-delivery service covers the following areas:

1. Engine Compartment and Undercarriage:
• Inspect for broken mounting brackets.
• Inspect and identify locations of any fluid leaks.
• General inspection of hoses, wiring, and linkage, focusing on potential wear points. • Verify correct fluid capacities for engine oil, coolant, power steering fluid, washer reservoir fluid, transmission fluid, rear-end fluid, pump transmission oil, and primer oil if applicable.
981
AGENDA ITEM NO. 28.
5 • Re-torque U-bolts to OEM specifications if equipped with leaf spring suspension (Pierce Custom chassis only).

2. Interior:
• Confirm proper operation of doors, windows, and locks, ensuring accurate adjustment.
• Confirm proper operation of seatbelt alarms.
• Confirm proper operation of all compartment door alarms, as well as hose bed cover, ladder rack, light tower, and deck gun alarms.
• Ensure functionality of auxiliary power points, interior lighting, mirror, and seat controls, and if applicable - headsets and radios.
• Inspect upholstery for quality and condition.

3. Exterior:
• Address reasonable paint scratches or chips.
• Tighten any loose hardware.
• Inspect tires and wheels, ensure proper pressure.
• Check compartment doors for proper operation and latch fit. • Lubricate compartment door locks if applicable.

4. Road Test:
• Conduct a road test with a full water tank (if applicable), covering approximately twenty miles on both city and highway roads.
• Perform a DOT compliant brake test to verify the system is holding air. • Inspect brake condition, wheel seals, and ensure drive train components reach optimal operating temperatures.
• Conduct an Allison Transmission self-diagnostic to verify fluid level, fluid and filter life, and check for fault codes.

5. Electrical:
• Verify the operation of all lights, sirens, and other electrical accessories.

6. Pump:
• Operate the Pressure Governor or Relief Valve, transfer valve, and check pump shift. • Inspect water tank, pump and plumbing for leaks and calibrate the water level gauge.
• Ensure smooth operation of all discharge, suction, and drain valves.

7. Pierce Husky™ Foam System:
982
AGENDA ITEM NO. 28.
6 • If applicable, draft and inject clean water to ensure proper operation of the foam pump.

8. Fuel and DEF Tanks:
• Fill the fuel tank and DEF tank prior to final delivery.

9. Wash:
• Thoroughly wash the apparatus prior to final delivery.

This pre-delivery service assists the apparatus to meet our high standards of quality and operational efficiency before reaching its final destination.

FINAL DELIVERY (CUSTOMER LOCATION)
GSFA will deliver the completed Product, inclusive of any relevant equipment, spare parts, and supplies, to the Customer's specified address at GSFA's expense.

In preparation for the Product's delivery, the Customer is required to furnish GSFA with proof of liability and physical damage insurance. GSFA will withhold the release of the Product until such proof of insurance is provided.

To ensure a timely delivery process, it is incumbent upon the Customer to settle any outstanding balance owed to GSFA before or at the time the Product is completed and ready for delivery. In the event of delayed payment or delivery, GSFA reserves the right to impose a late fee and daily storage charge as outlined in the Standard Terms and Conditions until payment is received.

For compliance with insurance liability considerations, the Product will only be delivered upon full acceptance and full payment, or through a prior written agreement mutually reached between the Customer and GSFA. This ensures a secure and efficient finalization of the delivery process, aligning with both parties' obligations and safeguarding against potential liabilities.

COMPREHENSIVE SALES AND SERVICE SUPPORT
At GSFA, we understand that immediate response is essential - and the service and support of your apparatus should be no different. Since our founding in 1989, our mission has been to provide first responders with the highest quality, most reliable fire and emergency apparatus from top-tier manufacturers. We specialize in guiding our customers through the entire process - from apparatus evaluation and customization to final inspection - and ensuring years of reliable service through our Golden State Emergency Vehicle Service (GSEVS) division.

Golden State Emergency Vehicle Service (GSEVS)
Established in 2014, GSEVS is committed to building long-term, collaborative relationships by providing exceptional warranty and technical support. Our services cover a wide range of needs, including chassis, 983
AGENDA ITEM NO. 28.
7 electrical systems, pump, aerial, routine maintenance, equipment mounting, and pump testing - with priority given to new units sold by GSFA. Our goal is to deliver prompt, professional service and unwavering support for your apparatus.

Sacramento Facility
Our Sacramento location features a 33,814-square-foot facility with 18 working bays and a 4,500- square-foot, two-story parts distribution department. Conveniently located near Highway 99 with easy access to Interstates 80 and 50, we are positioned to serve you efficiently.

Tracy Facility (Opening Fall 2025)
Our second location in Tracy will expand our service capacity with a 49,634-square-foot facility featuring 22 working bays and a parts department equal in size to our Sacramento facility. Strategically located within the "Tracy Triangle" - bordered by I-580, I-205, and I-5 - this facility will enhance our ability to serve customers in the Bay Area and beyond.

Certified and Experienced Technicians
Our service team includes factory-trained professionals certified by Pierce, ASE, and EVT. They undergo regular training to stay current on chassis, electrical systems, and aerial devices, ensuring expert handling of any challenge. Whether it's routine maintenance or complex diagnostics, you can count on expert care and precision with every visit.

Parts
At Golden State, we’re dedicated to keeping your apparatus fully operational and mission-ready. That’s why we maintain a robust inventory of both Pierce and non-Pierce parts—ready for immediate deployment when you need them most. If a part isn’t in stock, we expedite orders directly from the manufacturer to minimize downtime and get your unit back in service without delay.

To make the process even more efficient, our digital Parts Request Portal offers a streamlined, user- friendly experience. It provides 24/7 access to submit requests, monitor order status, and communicate directly with our team—ensuring transparent updates and quicker turnaround times every step of the way.

Mobile Service
To minimize emergency apparatus downtime, we offer a robust mobile service program for on-site repairs and maintenance.

Pre-Delivery Inspection (PDI) Process
We employ a dedicated team of Pre-Delivery Inspection (PDI) technicians solely focused on ensuring your apparatus arrives in peak condition. Before your new custom unit is delivered, it undergoes a thorough, multi-point inspection to verify quality, performance, and compliance with all specifications.

Our team handles every detail of the acceptance and delivery process—so you can take ownership with complete confidence and peace of mind.

Your Single Source for Sales and Service
With Golden State Fire, you have a single point of contact for sales, service, and support - all under one roof, with two strategically located facilities to serve you better. We are confident that our combination 984
AGENDA ITEM NO. 28.
8 of expertise, customer service, and product support is unmatched by any other fire and emergency apparatus dealership in California.

END OF EXHIBIT “D”

985
AGENDA ITEM NO. 28.

TO: Mayor and City Council
FROM: Finance Department
DATE: July 7, 2025
SUBJECT: Consider various actions related to Annexation of Territory (Annexation #76, T6452 N orthwest Corner Sunnyside / Perrin, T6467 Southeast Corner Minnewawa / Perrin, T6375 Northeast Corner Minnewawa / Shepherd) to the City of Clovis Community Facilities District No. 2004-1 (Police and Fire Services).

a. Consider Approval - Res. 2 5-___, A Re solution annexing territory (Annexation #7 6) ( T6452 N orthwest Corner Sunnyside/Perrin, T6467 Southeast Corner Minnewawa/Perrin, T6375 N ortheast Corner Minnewawa/Shepherd) to the City of Clovis Community Facilities District No. 2004-1 (Police and Fire Services) and calling a special landowner election to annex territory (Annexation #76) to City of Clovis Community Facilities District No. 2004-1 (Police and Fire Services).

b. Consider Approval - Res. 25-___, A Resolution of the City of Clovis declaring the results of a special landowner election and directing recording of the Notice of Special Tax Lien for City of Clovis Community Facilities District No. 2004-1 (Police and Fire Services).

Staff: Angela Papazian, Deputy Finance Director
Recommendation: Approve

ATTACHMENTS: 1. Resolution of Qualified Electors

2. Resolution Declaring Results

RECOMMENDATION
 That the Council hold a public hearing and approve actions related to the Annexation of Territory (Annexation #76) to Community Facilities District No. 2004-1.

 Consider Approval – Res. 25-___, A Resolution of annexation of territory (Annexation #76) to the Community Facilities District (City of Clovis Community Facilities District No. 2004-1) and to authorize the levy of Special Taxes therein and submitting Levy of Special Taxes to Qualified Electors.

986
AGENDA ITEM NO. 29.
 Call for Special Election and have Clerk announce the vote.

 Consider Approval – Res. 25-___, A Resolution of the City Council of the City of Clovis Declaring the Results of the Special Annexation Election, Determining Validity of Prior Proceedings and Directing Recording of the Notice of Special Tax Lien (City of Clovis Community Facilities District No. 2004-1) (Police and Fire Services).

EXECUTIVE SUMMARY
Since the condition to establish a CFD was imposed on the developments being processed by the City, developments proceeding after March 8, 2004, must petition to be annexed to the existing CFD. Several property owners have submitted petitions to annex territory to the Community Facilities District 2004-1 and to include their property within the District as provided by the conditions of approval of the development entitlements.

To initiate the process for annexation of territory to a CFD, the Council approved a Resolution of Intention-Annexation #76 (ROI) to annex territory to the CFD on June 2, 2025. The ROI set a public hearing for July 7, 2025. The action today finalizes the annexation to the CFD.

BACKGROUND
Since the condition to establish a CFD was imposed on the developments being processed by the City, developments proceeding after March 8, 2004, must petition to be annexed to the existing CFD. Several property owners have submitted petitions to annex territory to the Community Facilities District 2004-1 and to include their property within the District as provided by the conditions of approval of the development entitlements.

To initiate the process for annexation of territory to a CFD, the Council approved a Resolution of Intention-Annexation #76 (ROI) to annex territory to the CFD. The ROI set a public hearing for July 7, 2025. The Rate and Method of Apportionment (RMA) referred to in the ROI is the same as adopted by the Council with the Resolution of Formation adopted March 8, 2004. RMA provides, among other things, definitions, identifies what properties will be taxed, and the maximum special tax.

The conditions as provided in the Rate and Method of Apportionment will apply to territory annexed to the Community Facilities Districts to pr ovide funding for public safety operations in new growth areas. The major conditions include:

1. The maximum annual tax will be $2 93.55 for single family residential and $2 53.46 for multi-family residential.

2. The maximum tax will be increased by the Escalato r Factor, which is the greater of the change in CPI or percentage change in population.

3. There will be a review not later than five years of inception of the CFD.

4. The annual tax will not apply to commercially zoned property.

5. The tax will apply only to that property for which a building permit is issued after January 1, 2004.

6. The costs of salary and benefit increases funded by the CFD will be limited to the Escalator Factor.

987
AGENDA ITEM NO. 29.

The purpose of the hearing is to take public comment on the annexation of territory to the CFD and to accept protests from any interested person within the proposed boundaries. If no property owner protests are received, the Council may take the initial actions to annex the territory to the CFD by approving a resolution on the annexation to the CFD and calling a special property owner election. Once the election is called, the City Clerk tabulates the ballots. If the property owners of two -thirds (2/3) of the property within the proposed boundaries vote in favor of the CFD, then the Council can take action to direct the recording of Notice of Special Tax Lien. A unanimous vote is required to have the election the same night as approval of the resolution of annexation. The recording of the Tax Lien is contingent upon the property being annexed to the City. The property included within the CFD is being processed for annexation to the City and the Local Agency Formation Commission has approved the annexations.

After the annexation is complete and the Notice of Tax Lien has been recorded, any final maps within the CFD may be recorded and construction permits for homes can be issued. One of the conditions of the CFD is that the tax will only be collected on those properties where a building permit for a residence has been issued.

FISCAL IMPACT
If approved, residential units built within the boundaries of the CFD will be assessed annually according to the conditions of the CFD formation and those assessments will be utilized to fund police and fire services.

REASON FOR RECOMMENDATION
All requirements for the annexation of territory to the CFD have been completed and the Council may take action to annex territory to the CFD.

ACTIONS FOLLOWING APPROVAL
After approval of the resolution directing the recordation of the Notice of Tax Lien, the lien will be recorded.

CONFLICT OF INTEREST
None.

Prepared by: Steve Nourian, Senior Accounting Systems Technician

Reviewed by: City Manager AH

988
AGENDA ITEM NO. 29.

ATTACHMENT 1

RESOLUTION 25-

RESOLUTION OF THE CITY COUNCIL OF THE CITY OF CLOVIS APPROVING

ANNEXATION OF TERRITORY TO COMMUNITY FACILITIES DISTRICT AND TO

AUTHORIZE THE LEVY OF SPECIAL TAXES THEREIN AND SUBMITTING LEVY OF

SPECIAL TAXES TO QUALIFIED ELECTORS

CITY OF CLOVIS
Community Services District No. 2004-1
(Police and Fire Services)
Annexation No. 76

WHEREAS, this Council, on June 2, 2025, adopted A Resolution of Intention to Annex Territory to the Community Services District and to Authorize the Levy of Special Taxes Therein (the “Resolution of Intention”) stating its intention to annex the territory to the City’s Community Services District 2004-1 (the “District”), pursuant to Mello Roos Community Facilities Act of 1982, Sections 53311 and following of the California Government Code (the “Act”); and

WHEREAS, a copy of the Resolution of Intention, incorporating a description and map (Attachment A) of the proposed boundaries of the territory to be annexed to the District and stating the services to be provided and the rate and method of apportionment of the special tax to be levied within the District to pay for the services for the District, is on file with the Clerk of the Council and the provisions thereof are fully incorporated herein by this reference as if fully set forth herein; and

WHEREAS, on the date hereof, this Council held a noticed public hearing as required by the Act and the Resolution of Intention relative to the pro posed annexation of territory to the District; and

WHEREAS, at such hearing all interested persons desiring to be heard on all matters pertaining to the annexation of territory to the District and the levy of said special taxes within the area proposed to be annexed were heard and a full and fair hearing was held; and

WHEREAS, prior to the time fixed for said hearing, written protests had not been filed against the proposed annexation of territory to the District by (i) 50% or more of the registered voters, or six registered voters, whichever is more, residing in the existing District, or (ii) 50% or more of the registered voters, or six registered voters, whichever is more, residing in the territory proposed to be annexed to the District, or (iii) ow ners of one-half or more of the area of land in the territory proposed to be annexed to the District; and

WHEREAS, Annexation Map No. 76 to the District, has been filed with the City Clerk, which map shows the territory to be annexed in these proceedings, and a copy thereof is on file with the City Clerk.

989
AGENDA ITEM NO. 29.

NOW, THEREFORE, BE IT RESOLVED, by the City of Clovis as follows:

1. All prior proceedings taken by this Council with respect to the District and the proposed annexation of territory thereto have been duly considered and are hereby determined to be valid and in conformity with the Act, and the District has been validly established pursuant to the Act.

2. The description and map of the boundaries of the territory to be annexed to District, as described in said Annexation Map No. 76 to the District on file with the Clerk are hereby finally approved, are incorporated herein by reference, and shall be included within the boundaries of the District, and said territory is hereby ordered annexed to the District, subject to voter approval of the levy of the special taxes therein as hereinafter provided.

3. The provisions of the Resolution of Intention and Resolution No. 25-54 adopted by this Council for the District on June 2, 2025, each as heretofore adopted by this Council are by this reference incorporated herein, as if fully set forth herein.

4. Pursuant to the provisions of the Act, the proposition of the levy of the special tax within the territory to be annexed to the District shall be submitted to the voters of the area to be annexed to the District at an election called therefore as hereinafter provided.

5. This Council hereby finds that fewer than 12 persons have been registered to vote within the territory proposed to be annexed to the District for each of the 90 days preceding the close of the hearing heretofore conducted and concluded by this Council for the purposes of these annexation proceedings. Accordingly, and pursuant to the Act, this Council finds that for purposes of these proceedings th e qualified electors are the landowners within the territory proposed to be annexed to the District and that the vote shall be by said landowners, each having one vote for each acre or portion thereof such landowner owns in the territory proposed to be annexed to the District.

6. Pursuant to the Act, the election shall be conducted by mail ballot under Section 4000 of the California Elections Code. This Council hereby determines that paragraphs (a), (b), (c)(1), and (c)(3) of said Section 4000 are applicable to this election.

7. The Council hereby calls a special election to consider the measure described in the ballot referred to below, which election shall be held on July 7, 2025, in the regular meeting place of this Council, City Council Chambers, City Hall, 1033 5th Street, Clovis, California. This Council hereby further finds that the provision of the Act requiring a minimum of 90 days to elapse before said election is for the protection of voters and that the voters have waived such requirement and the date for the election herein specified is established accordingly.

8. The City Clerk is hereby appointed as the election official to conduct the election and shall cause to be provided to each landowner in the territory to be annexed to the District . The City Clerk shall accept the ballots of the qualified electors received prior to 5:00 o’clock p.m. on July 7, 2025, whether received by mail or by personal delivery.

990
AGENDA ITEM NO. 29.
* * * * *

The foregoing resolution was introduced and adopted at a regular meeting of the City Council of the City of Clovis held on July 7, 2025, by the following vote, to wit.

AYES:

NOES:

ABSENT:

ABSTAIN:

DATED: July 7, 2025

______________________________ ______________________________ Mayor City Clerk

991
AGENDA ITEM NO. 29.

Attachment A
992
AGENDA ITEM NO. 29.

ATTACHMENT 2
RESOLUTION 25-

RESOLUTION OF THE CITY COUNCIL OF THE CITY OF CLOVIS DECLARING

RESULTS OF SPECIAL ANNEXATION ELECTION, DETERMINING VALIDITY OF

PRIOR PROCEEDINGS, AND DIRECTING RECORDING OF AMENDED NOTICE OF

SPECIAL TAX LIEN

CITY OF CLOVIS
Community Facilities District No. 2004-1
(Police and Fire Services)
Annexation No. 76

WHEREAS, in proceedings heretofore conducted by the Council pursuant to the Mello-Roos Community Facilities Act of 1982, as amended (the “Act”), this Council has heretofore adopt ed a resolution calling a special election of the qualified landowner electors in the territory of land proposed to be annexed to Community Facilities District No. 2004-1 (Police and Fire Services) (the “CFD”); and

WHEREAS, pursuant to the terms of the re solution which is hereby incorporated herein by this reference, the special election has been held and the City Clerk has filed a Canvass of Votes Cast in Special Election, a copy of which is attached hereto as Attachment A; and

WHEREAS, this Council has reviewed the Canvass and hereby approves it.

NOW, THEREFORE, BE IT RESOLVED, by the City of Clovis as follows:

1. The issue presented at the special election was the levy of a special tax within the territory annexed to the CFD, to be levied in accordance with the formula heretofore approved by this Council as described in Resolution No. 25- , a Resolution of Annexation of Territory to Community Facilities District, authorizing the Levy of a Special Tax and Submitting Levy of Tax to Qualified Electors, adopted July 7, 2025.

2. Pursuant to the Canvass on file with the City Clerk, the issue presented at the special election was approved by the landowners of the territory annexed to the CFD by more than two-thirds (2/3) of the landowners voting at the special election.

3. Pursuant to the voter approval, said annexed territory to the CFD is hereby declared to be fully an nexed to and part of the CFD and this Council may levy special taxes therein as heretofore provided in these proceedings.

4. It is hereby found that all prior proceedings and actions taken by this Council pursuant to the CFD and the territory annexed ther eto were valid and in conformity with the Act.

993
AGENDA ITEM NO. 29.

Within 15 days of the date hereof, the City Clerk shall execute and cause to be recorded in the office of the County Recorder of the County of Fresno, an amendment to the Notice of Special Tax Lien as required by Section 3117.5 of the California Streets and Highways Code.

* * * * *

The foregoing resolution was introduced and adopted at a regular meeting of the City Council of the City of Clovis held on July 7, 2025, by the following vote, to wit.

AYES:

NOES:

ABSENT:

ABSTAIN:

DATED: July 7, 2025

______________________________ ______________________________ Mayor City Clerk

994
AGENDA ITEM NO. 29.

ATTACHMENT A

CITY OF CLOVIS
Community Facilities District No. 2004-1
(Police and Fire Services)
Annexation No. 76

CANVASS AND STATEMENT OF RESULT OF ELECTION

I hereby certify that on this date, I canvassed the returns of the election held on this date, in the territory annexed to Community Facilities District No. 2004 -1 (Police and Fire Services) of the City of Clovis which election is designated as the Special Tax Annexation Election, and the total number of ballots cast in the territory to be annexed and the total number of votes cast for and against the measure are as follows and the totals as shown for and against the measure are full, true and correct:

Qualified
Landowner
Votes
Votes
Cast
YES NO
City of Clovis
Community Facilities District No. 2004-1
(Police and Fire Services), Annexation No. 76
Special Tax Annexation Election,
July 7, 2025.

BALLOT MEASURE: Shall the City of Clovis, by and for its Community Facilities District No. 2004 -1 (Police and Fire Services) (the “CFD”), be authorized to levy special taxes within the territory annexed to the CFD pursuant to and as described in Resolution No. 25-___ of the City of Clovis, adopted by its Council on July 7, 2025?

IN WITNESS WHEREOF, I HAVE HEREUNTO SET MY HAND this ____ day of 2025.

CITY OF CLOVIS

By:

City Clerk

995
AGENDA ITEM NO. 29.