Agenda packet — Grass Valley City Council, April 8, 2025 (part 3 of 4)

Item # 9.
0644874 Warranty, Axle, 3 Year, TAK-4, IRS,
WA0249
REAR AXLE THREE (3) YEAR MATERIAL AND WORKMANSHIP WARRANTY Pierce TAK-4® independent rear suspension will be provided with a three (3) year material and workmanship limited warranty. The manufacturer's warranty will provide that the independent rear suspension be free from any defect related to material and workmanship on the portion of the apparatus built by the manufacturer that would arise under normal use and service. 0652758 Warranty, ABS Brake System, 3 Year,
Meritor Wabco, WA0232
ABS BRAKE SYSTEM THREE (3) YEAR MATERIAL AND WORKMANSHIP WARRANTY A Meritor Wabco™ ABS brake system limited warranty certificate, WA0232, is included with this proposal.
0019914 Warranty, Structure, 10 Year, Custom
Cab, WA0012
TEN (10) YEAR STRUCTURAL INTEGRITY
The Pierce custom cab limited warranty certificate, WA0012, is included with this proposal. 0744240 Warranty, Paint, 10 Year, Cab, ProRate, WA0055 TEN (10) YEAR PRO-RATED PAINT AND CORROSION A Pierce cab limited pro-rated paint warranty certificate, WA0055, is included with this proposal. 0524627 Warranty, Electronics, 5 Year, MUX,
WA0014
FIVE (5) YEAR MATERIAL AND WORKMANSHIP
The Pierce Command Zone electronics limited warranty certificate, WA0014, is included with this proposal.
0695416 Warranty, Pierce Camera System,
WA0188

CAMERA SYSTEM WARRANTY
A Pierce fifty four (54) monthwarranty will be provided for the camera system. 0708760 Warranty, Not Applicable, LED Strip
Lights

COMPARTMENT LIGHT WARRANTY
The compartment lights will not offer an extended warranty. 0046369 Warranty, 5-year EVS Transmission,
Standard Custom, WA0187

TRANSMISSION WARRANTY
The transmission will have a five (5) year/unlimited mileage warranty covering 100 percent parts and labor. The warranty will be provided by Allison Transmission.

Note: The transmission cooler is not covered under any extended warranty you may be getting on your Allison Transmission. Please review your Allison Transmission warranty for coverage limitations.
0685945 Warranty, Transmission Cooler,
WA0216

TRANSMISSION COOLER WARRANTY
The transmission cooler will carry a five (5) year parts and labor warranty (exclusive to the transmission cooler). In addition, a collateral damage warranty will also be in effect for the first three (3) years of the warranty coverage and will not exceed $10,000 per occurrence. A copy of the warranty certificate will be included with this proposal. 0688798 Warranty, Water Tank, Lifetime, UPF,
Poly Tank, WA0195

WATER TANK WARRANTY
A UPF poly water tank limited warranty certificate, WA0195, is included with this proposal. 0596025 Warranty, Structure, 10 Year, Body,
WA0009
TEN (10) YEAR STRUCTURAL INTEGRITY
The Pierce apparatus body limited warranty certificate, WA0009, is included with this proposal. 0693127 Warranty, Gortite, Roll-up Door, 6
Year, WA0190

ROLL UP DOOR MATERIAL AND WORKMANSHIP WARRANTY
A Gortite roll-up door limited warranty will be provided. The mechanical components of the roll-up door will be warranted against defects in material and workmanship for the lifetime of the vehicle.

A six (6) year limited warranty will be provided on painted and satin roll up doors.

The limited warranty certificate, WA0190, is included with this proposal. 0734463 Warranty, Pump, Waterous, 7 Year
Parts, WA0382

PUMP WARRANTY
The Waterous pump will be provided with a seven (7) yearmaterial and workmanship limited warranty.

A copy of the warranty certificate will be included with this proposal. 0648675 Warranty, 10 Year S/S Pumbing,
WA0035
TEN (10) YEAR PUMP PLUMBING WARRANTY
The Pierce apparatus plumbing limited warranty certificate, WA0035, is included with this proposal.
0657990 Warranty, Foam System, Husky 3,
WA0231

FOAM SYSTEM WARRANTY
The Husky 3 foam system limited warranty certificate, WA0231, is included with this proposal.

Bid #: 977 72

Page 190 ends

Item # 9.
0006999 Warranty, Structure, 20 Year, Aerial
Device, WA0052
TWENTY (20) YEAR AERIAL DEVICE STRUCTURAL INTEGRITY WARRANTY The Pierce device limited warranty certificate, WA0052, is included with this proposal. 0687388 Warranty, Swivels, 5 Year, Aerial
Device, WA0197

AERIAL SWIVEL WARRANTY
An Amity five (5) year limited swivel warranty will be provided. A copy of the warranty certificate will be included with this proposal.
0685727 Warranty, Hydraulic System and
Components, 3 Year/5 Year, WA0200

HYDRAULIC SYSTEM COMPONENTS WARRANTY
Aerial hydraulic system components will be provided with a five (5) year material and workmanship limited warranty.

HYDRAULIC SEAL WARRANTY
Aerial hydraulic seals will be provided with a three (3) year material and workmanship limited warranty.

A copy of the warranty certificates is included with this proposal. 0687327 Warranty, Waterway, 10 Year, Aerial
Device, WA0198

AERIAL WATERWAY WARRANTY
An Amity ten (10) year limited waterway warranty will be provided. A copy of the warranty certificate is included with this proposal.
0595860 Warranty, Paint, 4 Year, Aerial
Device, Pro-Rated, WA0047

FOUR (4) YEAR PRO-RATED PAINT AND CORROSION
A Pierce aerial device limited pro-rated paint warranty certificate, WA0047, is included with this proposal.
0595820 Warranty, Paint, 10 Year, Body, ProRate, WA0057 TEN (10) YEAR PRO-RATED PAINT AND CORROSION A Pierce body limited pro-rated paint warranty certificate, WA0057, is included with this proposal. 0595412 Warranty, Graphics Lamination, 1
Year, Apparatus, WA0168

ONE (1) YEAR MATERIAL AND WORKMANSHIP
The Pierce graphics fading and deterioration limited warranty limited warranty certificate, WA0168, is included with this proposal.
0819254 Certification, Vehicle Stability,
CD0196

VEHICLE STABILITY CERTIFICATION
The fire apparatus manufacturer will provide a certification stating the apparatus complies with NFPA 1900, current edition, section 7.14, Vehicle Stability. The certification is included with this proposal.
0807817 Certification, Engine Installation, Enf,
Cummins X15, 2024

ENGINE INSTALLATION CERTIFICATION
The fire apparatus manufacturer will provide a certification, along with a letter from the engine manufacturer stating they approve of the engine installation in the bidder's chassis. The certification will be provided at the time of delivery. 0686786 Certification, Power Steering,
CD0098

POWER STEERING CERTIFICATION
The fire apparatus manufacturer will provide a certification stating the power steering system as installed meets the requirements of the component supplier. The certification is included with this proposal.

Bid #: 977 73

Page 191 ends

Item # 9.
0892691 Certification, Cab Integrity, Saber
FR/Enforcer, CD0189

CAB INTEGRITY CERTIFICATION
The fire apparatus manufacturer will provide a cab crash test certification with this proposal. The certification will state that a specimen representing the substantial structural configuration of the cab has been tested and certified by an independent third party test facility. Testing events will be documented with photographs, real-time and high-speed video, vehicle accelerometers, cart accelerometers, and a laser speed trap. The fire apparatus manufacturer will provide a state licensed professional engineer to witness and certify all testing events. Testing will meet or exceed the requirements below:

SAE J2422 Cab Roof Strength Evaluation - Quasi-Static Loading Heavy Trucks.

European Occupant Protection Standard ECE Regulation No.29.

SAE J2420 COE Frontal Strength Evaluation - Dynamic Loading Heavy Trucks.

Side Impact
The cab will be subjected to dynamic preload where a 14,320-lb moving barrier is slammed into the side of the cab at 5.50 mph, striking with an impact of 13,000 ft-lb of force. This test is part of the SAE J2422 test procedure and more closely represents the forces a cab will see in a rollover incident.

Frontal Impact
The same cab will withstand a frontal impact of 32,600 ft-lb of force using a moving barrier in accordance with SAE J2420.

Additional Frontal Impact
The same cab will withstand a frontal impact of 65,098 ft-lb of force using a moving barrier. (Twice the force required by SAE J2420)
Roof Crush
The cab will be subjected to a roof crush force of 22,500 lb. This value meets the ECE 29 criteria, and is equivalent to the front axle rating up to a maximum of ten (10) metric tons.

Additional Roof Crush
The same cab will be subjected to a roof crush force of 110,000 lbs. (Four and a half times the load criteria of ECE 29)
The same cab will withstand all tests without any measurable intrusion into the survival space of the occupant area.

There will be no exception to any portion of the cab integrity certification. Nonconformance will lead to immediate rejection of bid.
0631973 Certification, Cab Door Durability,
Saber FR/Enforcer, CD0137

CAB DOOR DURABILITY CERTIFICATION
Robust cab doors help protect occupants. Cab doors will survive a 200,000 cycle door slam test where the slamming force exceeds 20 G's of deceleration. The bidder will certify that the sample doors similar to those provided on the apparatus have been tested and have met these criteria without structural damage, latch malfunction, or significant component wear. 0631978 Certification, Windshield Wiper
Durability, Saber FR/Enforcer,
CD0132

WINDSHIELD WIPER DURABILITY CERTIFICATION
Visibility during inclement weather is essential to safe apparatus performance. Windshield wipers will survive a 3 million cycle durability test in accordance with section 6.2 of SAE J198 Windshield Wiper Systems - Trucks, Buses and Multipurpose Vehicles. The bidder will certify that the wiper system design has been tested and that the wiper system has met these criteria. 0631974 Certification, Electric Window
Durability, Saber FR/Enforcer,
CD0133

ELECTRIC WINDOW DURABILITY CERTIFICATION
Cab window roll-up systems can cause maintenance problems if not designed for long service life. The window regulator design will complete 30,000 complete up-down cycles and still function normally when finished. The bidder will certify that sample doors and windows similar to those provided on the apparatus have been tested and have met these criteria without malfunction or significant component wear.
0631977 Certification, Seat Belt Anchors and
Mounting, Saber FR/Enforcer,
CD0134

SEAT BELT ANCHOR STRENGTH
Seat belt attachment strength is regulated by Federal Motor Vehicle Safety Standards and should be validated through testing. Each seat belt anchor design will withstand 3000 lb of pull on both the lap and shoulder belt in accordance with FMVSS 571.210 Seat Belt Assembly Anchorages.

The bidder will certify that each anchor design was pull tested to the required force and met the appropriate criteria.

SEAT MOUNTING STRENGTH
Seat attachment strength is regulated by Federal Motor Vehicle Safety Standards and should be validated through testing. Each seat mounting design will be tested to withstand 20 G's of force in accordance with FMVSS 571.207 Seating Systems. The bidder will certify, at time of delivery, that each seat mount and cab structure design was pull tested to the required force and met the appropriate criteria.

Bid #: 977 74

Page 192 ends

Item # 9.
0735949 Certification, Cab HVAC System
Performance, SFR/Enf,
CD0165/CD0167/CD0174/CD0175

PERFORMANCE CERTIFICATIONS
Cab Air Conditioning
Good cab air conditioning temperature and air flow performance keeps occupants comfortable, reduces humidity, and provides a climate for recuperation while at the scene. The cab air conditioning system will cool the cab from a heat-soaked condition at 100 degrees Fahrenheit to an average of 78 degrees Fahrenheit in 30 minutes. The bidder will certify that a substantially similar cab has been tested and has met these criteria.

Cab Defroster
Visibility during inclement weather is essential to safe apparatus performance. The defroster system will clear the required windshield zones in accordance with SAE J381 Windshield Defrosting Systems Test Procedure And Performance Requirements - Trucks, Buses, And Multipurpose Vehicles.The bidder will certify that the defrost system design has been tested in a cold chamber and passes the SAE J381 criteria.

Cab Auxiliary Heater
Good cab heat performance and regulation provides a more effective working environment for personnel, whether in-transit, or at a scene. An auxiliary cab heater will warm the cab 77 degrees Fahrenheit from a cold-soak, within 30 minutes when tested using the coolant supply methods found in SAE J381. The bidder will certify, at time of delivery, that a substantially similar cab has been tested and has met these criteria.
0545073 Amp Draw Report, NFPA Current
Edition

AMP DRAW REPORT
The bidder will provide, at the time of bid and delivery, an itemized print out of the expected amp draw of the entire vehicle's electrical system.

The manufacturer of the apparatus will provide the following:

Documentation of the electrical system performance tests.

A written load analysis, which will include the following:

The nameplate rating of the alternator.

The alternator rating under the conditions specified per:

Current edition of applicable NFPA standards.

The minimum continuous load of each component that is specified per:

Current edition of applicable NFPA standards.

Additional loads that, when added to the minimum continuous load, determine the total connected load.

Each individual intermittent load.

All of the above listed items will be provided by the bidder per the current edition of applicable NFPA standards.
0002758 Amp Draw, NFPA/ULC Radio
Allowance
0799247 Appleton/Florida Stock Unit

0000049 Ascendant BODY

0000012 PIERCE CHASSIS
0004713 ENGINE, OTHER
0046396 EVS 4000 Series TRANSMISSION
0020011 WATEROUS PUMP

0020009 POLY TANK

0028048 FOAM SYSTEM
0020006 SIDE CONTROL
0020007 AKRON VALVES

0020015 ABS SYSTEM

0658751 PUMPER BASE

Bid #: 977 75

Page 193 ends

Item # 9.

Option Description Type* Minimum
Load
Intermittent
Load
Total
Connected
0001244 High Idle w/Electronic Engine, Custom 0.00 1.20 0.00 0002617 PTO switch, w/light - aerial 0.00 0.00 0.08
0062992 Gauge, Foam Level, (1) Tank, Class 1, GAAAR 5lt 0.00 0.00 1.00 0072153 Primer, Trident, Air Prime, Air Operated 0.00 0.00 0.00 0079211 Batteries, (6) Stryten/Exide Grp 31, 950 CCA each, Threaded Stud 0.00 3.00 0.00 0543751 Light, Do Not Move Apparatus 0.00 0.80 0.00
0549333 Indicators, Engine, Included with Pressure Controller 0.00 0.35 0.00 0553643 Control, Air Horn at Pmp Pnl, Red Switch, Momentary 0.00 0.16 0.00 0583824 Light, Pump Compt, Wln 3SC0CDCR LED White 0.00 0.36 0.00 0583938 Lights, Engine Compt, Custom, Auto Sw, Wln 3SC0CDCR, 3" LED, Trim

0.00 0.30 0.00
0589905 Alarm, Back-up Warning, PRECO 1040 0.00 0.50 0.00 0592633 Foam Sys, Husky 3, Single Agent 0.00 55.00 0.00 0630636 Controls, Electric Roll-Up Windows, 4dr, 4 Driver Controls, Saber FR/Enforcer

0.00 26.00 0.00
0644201 Cab Lift, Elec/Hyd, Saber FR/Enforcer 0.00 180.00 0.00 0653677 Lighting, Rung, LED, TecNiq, 4 Section, Base, Lower/Upper Mid, Fly

0.00 0.00 7.20
0687994 Engine Brake, Jacobs Compression Brake, Cummins Engine 0.00 0.42 0.00 0722038 HVAC, Heavy-Duty, Enforcer, w/X15, CARE 0.00 0.00 100.00 0746513 Water Level Gauge, Wln 50*02Z*R LED w/Flange, Gr-Bl-Amb-Rd, Features

0.00 0.00 4.00
0757717 Lights, HiViz FT-B-65-* LED, 2nd 0.00 0.00 21.30 0757722 Lights, HiViz FT-B-65-* LED, 1st 0.00 0.00 21.30 0768059 Lights, Wln, PCPSM2* Pioneer, 12 VDC, 2nd 0.00 0.00 12.00 0768061 Lights, Wln, PCPSM2* Pioneer, 12 VDC, 1st 0.00 0.00 12.00 0776995 Light, Roof Mt, HiViz, FT-MB-12-*-*, 17" 0.00 0.00 10.00 0792976 Stabilizers, Ascendant Tandem, Rear Mount Steel, 16' Spread, 18" Pen, MUX

0.00 4.00 0.00
0804781 Aerial Scene Lts Separated into Aerial Tip Category and Aerial Tracking Category

0.00 0.00 0.00
0806466 Lights, Backup, Wln M62BU, LED, For Tail Lt Housing 0.00 3.20 0.00 0816158 Camera, Pierce, LS Mux, RS, LS, R, Cameras, AHD 0.00 1.20 0.00 0821337 ABS Wabco Brake System, Tandem Rear Axle, Tak-4, NFPA 1900/ULC

0.00 6.00 0.00
0889727 Light, P25 LED, Compartment 0.00 0.00 0.10
0895310 Siren, Federal Q2B 0.00 100.00 0.00
0002615 Switch, Aerial 12V Master NFPA 0.08 0.00 0.00
0002758 Amp Draw, NFPA/ULC Radio Allowance NFPA 5.00 0.00 0.00 0010758 Flow Meter, Waterway, PAL, 110' Ascendant, MUX NFPA 0.50 0.00 0.00 0035382 Compt, RS Turntable, F/H, Roll Dr & Lift Dr, Ascendant Tandem, 105 HDL
NFPA 2.70 0.00 2.70
0063695 Compt, LS F/H F/D, Roll Drs, w/o Chute, Ascendant Tandem, 105', 100 HAL
NFPA 2.70 0.00 2.70
0063727 Compt, LS Turntable, F/H F/D, Roll Dr & Lift Dr, Ascendant Tandem, 105'
NFPA 1.80 0.00 1.80
0063733 Compt, RS F/H, Roll Drs, Ascendant Tandem, 105 HDL, 100 HAL NFPA 3.60 0.00 3.60 0068703 Lights, Grote Supernova LED, Stabilizer Beam, (1) Set NFPA 1.60 0.00 0.00 0092582 Load Manager/Sequencer, MUX NFPA 0.56 0.56 0.00 0511569 Lights, Clearance/Marker/ID, Rear, P25 LED 7Lts NFPA 0.50 0.00 0.00 0534828 Siren, Wln 295SL101, 100 or 200W Removable Mic NFPA 0.80 7.20 0.00 0586382 Gauges, Engine, Included With Pressure Controller NFPA 0.30 0.00 0.00 0589378 Lights, Step, P25 LED, Aerial With Pump, Ign, Prk Brk Set NFPA 1.50 0.00 0.00 0593161 Light Shield, S/S LED NFPA 3.00 0.00 0.00
0601949 Light, Turntable Console, TecNiq T-10, LED Strip Light NFPA 0.20 0.00 0.00 0601972 Lights, Turntable Walkway, P25, LED NFPA 0.35 0.00 0.00 0602100 Lights, Torque Box Ladder Storage, Pierce LED Strip Lights, 2 Lts NFPA 1.00 0.00 0.00 * UDMC = User Defined Mission Critical, LM = User Defined Load Managed, S = Electrical Amperage Supply 1 Electrical Analysis 3/25/2025
Bid #: 977
Enforcer Ascendant 107' Ladder Quint Tandem T3 Sales Rep:

Organization:

Hansen, Brad
Golden State Fire Apparatus, Inc
Desc:

Job #:

Customer: City of Grass Valley
Option: Pierce Command Zone, Advanced Electronics & Control System, Enforcer, WiFi CZT
Type: Multiplexed

Page 194 ends

Item # 9.

Option Description Type* Minimum
Load
Intermittent
Load
Total
Connected
0604635 Lightbar, Wln, Freedom IV-Q, 2-21.5", RRRWR RWRRR NFPA 6.48 2.48 7.28 0605126 Pump Shift, Air Mnl Override, Split Shaft, Interlocked, Waterous NFPA 1.00 0.00 0.00 0620054 Light, Directional/Marker, Intermediate, Weldon 9186-8580-29 LED 2lts
NFPA 0.10 0.90 0.00
0622803 Cab Instruments, Black Gauges, Black Bezels, Enforcer MUX NFPA 1.26 0.00 0.00 0625210 Lights, Directional, Cab Front Side, Truck-Lite 19036Y LED, AXT/Enf
NFPA 0.12 0.00 0.00
0625953 Light, Directional, Wln 600 Cmb, Cab Crn, Wrp Bzl Out HD Lts, Enf/Sab
NFPA 0.70 0.70 0.00
0647647 Lights, Dome, FRP Dual LED 4 Lts NFPA 0.80 0.80 0.00 0647802 Lights, Clearance/Marker/ID, Front, P25 LED 5 Lts, Saber FR/Enforcer
NFPA 0.35 0.00 0.00
0653937 Flasher, Headlight Alternating NFPA 0.08 0.00 0.00 0667186 Light, Slide-Out Pump Operator Step, OSS Access LED, Short Step
NFPA 0.65 0.00 0.00
0709438 Lights, Walk Surf, FRP Flood, LED NFPA 2.00 0.00 0.00 0731813 Hour Meter, Aerial, Included in Information Centers, ASL, AAT, ASP
NFPA 0.10 0.00 0.00
0737181 Intercom, 2-Way Fire Research ICA910 Hands Free NFPA 0.50 0.00 0.00 0739224 Indicator Light @ Pump Panel, Throttle Ready, Incl w/Pressure Gov/Throttle,Green
NFPA 0.10 0.00 0.00
0745568 Indicator Light, Pump Panel, Ok To Pump, Green NFPA 0.10 0.00 0.00 0747228 Lights, Side Zone Lower, Wln M6**, M6**, M6**, 6Lts NFPA 5.40 8.10 0.00 0747261 Lights, Stabilizer Warn (2) Sets, Wln M6** LED, Trim Color NFPA 3.60 5.40 0.00 0755095 Aerial, 107' ASL Tandem, 750/500 Tip, 50 MPH NFPA 5.00 0.00 0.00 0757359 Gauge, Water Level, Class 1, Pierce Std, Remote Module Driver NFPA 1.23 0.00 0.00 0757962 Cabinet, Rear Facing, RS, 22 W x 40.25 H x 26.75 D, Roll, Ext Acc, SFR/Enf
NFPA 0.30 0.30 0.00
0757990 Cabinet, Rear Facing, LS, 23 W x 40.25 H x 26.75 D, Roll, Ext Acc, SFR/Enf
NFPA 0.78 0.78 0.00
0762388 Lights, Stabilizer Scene, (2) sets, Amdor AY-LB-12HW012, LED NFPA 0.72 0.00 0.00 0762413 Light, Boom Support, Amdor AY-LB-12HW012, 12" LED NFPA 0.18 0.00 0.00 0764563 DEF Tank, 8.0 Gallon, LS Fill, Forward of Rear Axle NFPA 0.60 11.40 0.00 0768765 Lights, Perimeter Body, Amdor AY-LB-12HW020 LED 2lts, Turntable Access
NFPA 0.33 0.00 0.00
0769420 Lights, Perimeter Cab, Amdor AY-LB-12HW020 LED 4Dr NFPA 1.20 0.00 0.00 0769564 Lights, Perimeter Pump House, Amdor AY-LB-12HW020 LED 1lt NFPA 0.30 0.00 0.00 0783157 Headlights, Rect LED, JW Spkr Evo 2, Heat,
AXT/DCF/Enf/Imp/Sab/Vel
NFPA 6.60 6.60 0.00
0789736 Cab, Enforcer, 7010 w/Notch NFPA 6.80 10.20 0.00 0790412 Air Dryer, Wabco System Saver 1200 IWT, Heated, SFR/Enf NFPA 7.81 0.00 0.00 0791501 Light, Traffic Directing, Wln TAL65, 36" Long LED, Aerials NFPA 0.60 1.20 0.00 0801890 Trans, Allison 6th Gen, 4500 EVS P, w/Prognostics, Imp/Vel/Enf NFPA 2.00 2.00 0.00 0802753 Lights, Tracking, Wln MP** LED, 2lts NFPA 8.00 0.00 0.00 0804514 Lights, Tail, Wln M62BTT* Red Stop/Tail & M62T* Amber Dir Arw For Hsg
NFPA 0.83 2.49 0.00
0809546 Light, Rear Zone Up, Wln L31H5F Beacons, Red w/Clear Lens, 2Lts
NFPA 4.00 4.00 0.00
0811237 Engine, Cummins X15, 605 hp, 1850 lb-ft, W/OBD, EPA 2024, Enforcer, BMP/HDR/STK
NFPA 10.00 0.00 0.00
0813791 Panel, Charger Display, Kussmaul, 091-94-12, Batt Dir NFPA 0.03 0.00 0.00 0814201 Vehicle Information Center, 7" Color Display, Touchscreen, MUX, CL714
NFPA 1.20 0.00 0.00
0814217 Control Stations, ASL Tandem Axle, MUX, Color Display, CL714 NFPA 4.26 0.00 0.00 0816093 ClearSky Telematics, Remote Fleet & On-scene Management, AT&T Commercial
NFPA 1.61 0.00 0.00
0820601 Lights, Tip, Wln MP** LED, 4lts NFPA 13.12 0.00 0.00 0826104 Controller, Pressure, FRC, Pump Boss Max, PBA500 NFPA 1.80 0.00 0.00 0827069 Lights, Rear Scene, Wln, MPB* Micro Pioneer LED, 2Lts NFPA 6.56 0.00 0.00 0889577 Bracket, License Plate & Light, P25 LED, Stainless Brkt NFPA 0.07 0.00 0.00 0892638 Lights, Cab & Crw Cab Acs Stps, P25, LED w/Bezel, 6lts NFPA 1.00 0.00 0.00 0892656 Lights, Step (6), P25 LED, Each Side NFPA 0.30 0.00 0.00 0894842 Lights, Rear Zn Lwr, Wln M6*, For Tail Lt Housings NFPA 1.80 2.70 0.00 0898617 Lights, Hose Bed, Sides, Dual Strips, 45 Ends NFPA 3.30 0.00 0.00 * UDMC = User Defined Mission Critical, LM = User Defined Load Managed, S = Electrical Amperage Supply 2 Electrical Analysis 3/25/2025
Bid #: 977
Enforcer Ascendant 107' Ladder Quint Tandem T3 Sales Rep:

Organization:

Hansen, Brad
Golden State Fire Apparatus, Inc
Desc:

Job #:

Customer: City of Grass Valley
Option: Pierce Command Zone, Advanced Electronics & Control System, Enforcer, WiFi CZT
Type: Multiplexed

Page 195 ends

Item # 9.

Option Description Type* Minimum
Load
Intermittent
Load
Total
Connected
0899300 Lights, Front Zone, Wln M6** M6RS M6RS M6**, Inside Steady Burn, 4lts Q Bez
NFPA 3.60 5.40 0.00
0647728 Alternator, 430 amp, Delco Remy 55SI S 0.00 0.00 0.00 Load Totals: 145.46 455.70 207.06
Minimum Continuous Load
Supply: 254.00
Demand: 145.46
Variance: 108.54
Total Connected Load
Supply: 370.00
Demand: 352.52
Variance: 17.48
Note: Minimum Continous Load is in "Blocking Right of Way" mode.(Reference current edition of NFPA 1901) Note: Intermittent Load items are not factored in on any alternator load comparisons. These items are included on the report for reference only and should be looked at as amp draw exclusion items. (Reference current edition of NFPA 1901) Note: Total Connected Load "Demand" represents Total Connected Load minus any Load Managed items Alternator Output at Idle: 254.00 Alternator Output at Governed Speed: 370.00 * UDMC = User Defined Mission Critical, LM = User Defined Load Managed, S = Electrical Amperage Supply 3 Electrical Analysis 3/25/2025
Bid #: 977
Enforcer Ascendant 107' Ladder Quint Tandem T3 Sales Rep:

Organization:

Hansen, Brad
Golden State Fire Apparatus, Inc
Desc:

Job #:

Customer: City of Grass Valley
Option: Pierce Command Zone, Advanced Electronics & Control System, Enforcer, WiFi CZT
Type: Multiplexed

Page 196 ends

Item # 9.

Turning Performance Analysis
Bid Number: 977 Chassis: Enforcer Chassis, Aerials, Tandem Axle, Ascendant/LSL Department: City of Grass Valley Body: Aerial, HD Ladder 107' ASL Tandem, Alum Body Parameters:
*Inside Cramp Angle: 45°
Axle Track: 82.92 in.

Wheel Offset: 4.68 in.

Tread Width: 16.3 in.

Chassis Overhang: 65.95 in.

Additional Bumper Depth: 13 in.

Front Overhang: 78.95 in.

Wheelbase: 249 in.

Calculated Turning Radii:

Inside Turn: 19 ft. 8 in.

Curb to curb: 35 ft. 8 in.

Wall to wall: 39 ft. 8 in.

Notes:
*Actual Inside cramp angle may be less than shown.

Curb to Curb turning radius calculated for 9.00 inch curb. 03/25/2025
Category Option Description
Bumpers 0606551 Bumper, 13" Extended, Steel Painted, Saber FR/Enforcer Aerial Devices 0755095 Aerial, 107' ASL Tandem, 750/500 Tip, 50 MPH Axle, Front, Custom 0629940 Axle, Front, Oshkosh TAK-4, Non Drive, 22,800 lb, Enforcer Wheels, Front 0752585 Wheels, Front, Alcoa, 22.50" x 12.25", Aluminum, Dura-Black, Hub Pilot Tires, Front 0899438 Tires, Front, Goodyear, Armor MAX MSA, 425/65R22.50, 20 ply

Page 197 ends

Item # 9.

Definitions:

Inside CrampAngle Maximum turning angle of the front inside fire.

Axle Track King-pin to King-pin distance of front axle.

Wheel Offset Offset from the center line of the wheel to the King-pin.

Tread Width Width of the tire tread.

Chassis Overhang Distance of the center line of the front axle to the front edge of the cab. This does not include the bumper depth.

Additional Bumper Wheel Depth that the bumper assembly adds to the front overhang.

Wheelbase Distance between the center lines of the vehicles front and rear axles.

Inside Turning Radius Radius of the smallest circle around which the vehicle can turn.

Curb to Curb Turning Radius Radius of the smallest circle around which the vehicle's tires can turn. This measures assumes a curb height of 9 inches.

Wall to Wall Turning Radius Radius of the smallest circle around which the vehicle's tires can turn. This measures takes into account any front overhang due to chassis , bumper extensions and or aerial devices.

Page 198 ends

Item # 9.

JROGHQVWDWHĆUHFRP

PRODUCT

WARRANTIES
Exhibit “C”
4

Page 199 ends

Item # 9.

Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 2/8/2010 WA0008

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.

This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

No specific exclusions apply
Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4
Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

Fire and Rescue Apparatus
Coverage:

One (1) Year Material and Workmanship
Basic Apparatus
Twelve (12) months. Warranty Period
Ends After:

The date the apparatus is placed in service, or 60 days from the original buyer invoice date, whichever comes first. Warranty Begins:

Portions of the apparatus manufactured by Pierce shall be free from defects in material and workmanship
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.

3. BUYER'S EXCLUSIVE REMEDY.

Page 200 ends

Item # 9.

Cummins Warranty
Worldwide
Fire Apparatus/Crash Trucks

Page 201 ends

Item # 9.

Coverage
Products Warranted
This Warranty applies to new diesel Engines sold by
Cummins and delivered to the first user on or after
April 1, 2007, that are used in fire apparatus truck and crash truck* applications Worldwide.

Base Engine Warranty
The Base Engine Warranty covers any failures of the
Engine which result, under normal use and service,
from a defect in material or factory workmanship
(Warrantable Failure). This Coverage begins with the
sale of the Engine by Cummins and ends five years or
100,000 miles (160,935 kilometers), whichever occurs
first, after the date of delivery of the Engine to the first user.

Engine aftertreatment components included in the
Cummins Critical Parts List (CPL) and marked with a
Cummins part number are covered under Base Engine
Warranty.

Additional Coverage is outlined in the Emission
Warranty section.

These Warranties are made to all Owners in the
chain of distribution and Coverage continues to all
subsequent Owners until the end of the periods of
Coverage.

Cummins
Responsibilities
Cummins will pay for all parts and labor needed to
repair the damage to the Engine resulting from a
Warrantable Failure.

Cummins will pay for the lubricating oil, antifreeze,
filter elements, belts, hoses and other maintenance
items that are not reusable due to the Warrantable
Failure.

Cummins will pay for reasonable labor costs for
Engine removal and reinstallation when necessary to
repair a Warrantable Failure.

Cummins will pay reasonable costs for towing a
vehicle disabled by a Warrantable Failure to the
nearest authorized repair location. In lieu of the towing expense, Cummins will pay reasonable costs for
mechanics to travel to and from the location of the
vehicle, including meals, mileage and lodging when
the repair is performed at the site of the failure.

Owner
Responsibilities
Owner is responsible for the operation and
maintenance of the Engine as specified in Cummins
Operation and Maintenance Manuals. Owner is also
responsible for providing proof that all recommended
maintenance has been performed.

Before the expiration of the applicable Warranty,
Owner must notify a Cummins distributor, authorized
dealer or other repair location approved by Cummins
of any Warrantable Failure and make the Engine
available for repair by such facility. Except for Engines disabled by a Warrantable Failure, Owner must also
deliver the Engine to the repair facility.

Service locations are listed on the Cummins Worldwide
Service Locator at cummins.com.

Owner is responsible for the cost of lubricating oil,
antifreeze, filter elements and other maintenance items provided during Warranty repairs unless such items
are not reusable due to the Warrantable Failure.

Owner is responsible for communication expenses,
meals, lodging and similar costs incurred as a result of a Warrantable Failure.

Owner is responsible for non-Engine repairs and for
‘‘downtime’’ expenses, cargo damage, fines, all
applicable taxes, all business costs and other losses
resulting from a Warrantable Failure.

Owner is responsible for a $100 (U.S. Dollars)
deductible per each service visit under this plan in the 3rd, 4th and 5th years of Base Engine Warranty. The
deductible will not be charged during the first 2 years of the Base Engine Warranty.

Limitations
Cummins is not responsible for failures or damage
resulting from what Cummins determines to be abuse
or neglect, including, but not limited to: operation
without adequate coolants or lubricants; overfueling;
overspeeding; lack of maintenance of lubricating,
cooling or intake systems; improper storage, starting,
warm-up, run-in or shutdown practices; unauthorized
modifications of the Engine.

Any unauthorized modifications to the aftertreatment
could negatively effect emissions certification and void Warranty.

Cummins is also not responsible for failures caused by
incorrect oil, fuel or diesel exhaust fluid or by water, dirt or other contaminants in the fuel, oil or diesel

Page 202 ends

Item # 9.
exhaust fluid.

This Warranty does not apply to accessories supplied
by Cummins which bear the name of another
company. Such non-warranted accessories include, but
are not limited to: alternators, starters, fans, air
conditioning compressors, clutches, filters,
transmissions, torque converters, vacuum pumps,
power steering pumps, fan drives and air compressors.

Cummins branded alternators and starters are covered
for the first two years from the date of delivery of the Engine to the first user, or the expiration of the Base Engine Warranty, whichever occurs first.

Failures resulting in excessive oil consumption are not covered beyond the duration of the Coverage or
100,000 miles (160,935 kilometers) or 7,000 hours from
the date of delivery of the Engine to the first user,
whichever of the three occurs first. Before a claim for excessive oil consumption will be considered, Owner
must submit adequate documentation to show that
consumption exceeds Cummins published standards.

Failures of belts and hoses supplied by Cummins are
not covered beyond the first year from the date of
delivery of the Engine to the first user or the duration of the Warranty, whichever occurs first.

Parts used to repair a Warrantable Failure may be new
Cummins parts, Cummins approved rebuilt parts or
repaired parts. Cummins is not responsible for failures resulting from the use of parts not approved by
Cummins.

A new Cummins or Cummins approved rebuilt part
used to repair a Warrantable Failure assumes the
identity of the part it replaced and is entitled to the remaining Coverage hereunder.

Cummins Inc. reserves the right to interrogate
Electronic Control Module (ECM) data for purposes of
failure analysis.

CUMMINS DOES NOT COVER WEAR OR WEAROUT
OF COVERED PARTS.

CUMMINS IS NOT RESPONSIBLE FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES.

THIS WARRANTY AND THE EMISSION WARRANTY

SET FORTH HEREINAFTER ARE THE SOLE

WARRANTIES MADE BY CUMMINS IN REGARD TO
THESE ENGINES. CUMMINS MAKES NO OTHER

WARRANTIES, EXPRESS OR IMPLIED, OR OF

MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE.

This Warranty gives you specific legal rights, and you
may also have other rights which vary from state to
state.

Emission
Warranty
Products Warranted
This Emission Warranty applies to new Engines
marketed by Cummins that are used in the United
States** in vehicles designed for transporting persons
or property on a street or highway. This Warranty
applies to Engines delivered to the first user on or after September 1, 1992.

Coverage
Cummins warrants to the first user and each
subsequent purchaser that the Engine is designed,
built and equipped so as to conform at the time of sale by Cummins with all U.S. federal emission regulations
applicable at the time of manufacture and that it is free from defects in material or factory workmanship which
would cause it not to meet these regulations within the longer of the following periods: (A) Five years or
100,000 miles (160,935 kilometers) of operation,
whichever occurs first, as measured from the date of
delivery of the Engine to the first user or (B) The Base Engine Warranty.

If the vehicle in which the Engine is installed is
registered in the state of California, a separate
California Emission Warranty also applies.

Limitations
Failures, other than those resulting from defects in
material or factory workmanship, are not covered by
this Warranty.

Cummins is not responsible for failures or damage
resulting from what Cummins determines to be abuse
or neglect, including, but not limited to: operation
without adequate coolants or lubricants; overfueling;
overspeeding; lack of maintenance of lubricating,
cooling or intake systems; improper storage, starting,
warm-up, run-in or shutdown practices; unauthorized
modifications of the Engine.

Any unauthorized modifications to the aftertreatment
could negatively effect emissions certification and void Warranty.

Cummins is also not responsible for failures caused by
incorrect oil, fuel or diesel exhaust fluid or by water, dirt or other contaminants in the fuel, oil or diesel
exhaust fluid.

Cummins is not responsible for non-Engine repairs,
‘‘downtime’’ expenses, cargo damage, fines, all
applicable taxes, all business costs or other losses
resulting from a Warrantable Failure.

Page 203 ends

Item # 9.

Cummins Inc.

Box 3005
Columbus, IN 47202-3005
U.S.A.

Bulletin 3381161
Printed in U.S.A. Rev. 08/09
©2001 Cummins Inc.

CUMMINS IS NOT RESPONSIBLE FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES.
* Airport operated crash trucks and fire department
operated trucks employed to respond to fires,
hazardous material releases, rescue and other
emergency-type situations.
** United States includes American Samoa, the
Commonwealth of Northern Mariana Islands, Guam,
Puerto Rico and the U.S. Virgin Islands.

Cummins Inc.

Box 3005
Columbus, IN 47202-3005
U.S.A.

Bulletin 3381161
Printed in U.S.A. Rev. 08/09 2001 Cummins Inc.

Page 204 ends

Item # 9.

Page 205 ends

Item # 9.

Page 206 ends

Item # 9.

Page 207 ends

Item # 9.

Page 208 ends

Item # 9.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This warranty applies to the frame rails only, crossmembers are excluded.

This warranty does not apply to damage caused by corrosion.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

3. BUYER'S EXCLUSIVE REMEDY.
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce.

Fifty (50) Years
(Expected Life of Apparatus)
Warranty Period
Ends After:

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

Fire and Rescue Apparatus
Coverage:

Lifetime Fifty (50) Year Structural Integrity
Custom Chassis Frame
Limited Warranty
Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

Custom chassis frame rail manufactured by Pierce shall be free from defects in material and workmanship

1. LIMITED WARRANTY
(b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the purchaser who first puts the product in service ("Buyer"):
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:

Page 209 ends

Item # 9.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This limited warranty excludes brake pads, brake rotors, seal boots and shock absorbers.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE
POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

Three (3) Years
-or30,000 Miles
Warranty Period
Ends After:

ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

Fire and Rescue Apparatus
Coverage:

Three (3) Year Material and Workmanship
TAK-4 Independent Front Suspension
Limited Warranty
Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

The TAK-4 Front Independent Suspension and Steering
Gears shall be free from defects in material and
workmanship.

1. LIMITED WARRANTY
(b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:

Page 210 ends

Item # 9.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This limited warranty excludes brake shoes, brake drums, ball joint boots and shock absorbers.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE
POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

Three (3) Years
-or30,000 Miles
Warranty Period
Ends After:

ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

Fire and Rescue Apparatus
Coverage:

Three (3) Year Material and Workmanship
TAK-4 Independent Rear Suspension
Limited Warranty
Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

The TAK-4 Rear Independent Suspension and Steering Gears shall be free from defects in material and workmanship.

1. LIMITED WARRANTY
(b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:

Page 211 ends

Item # 9.
)LUHDQG5HVFXH$SSDUDWXV
Coverage:
7KUHH

<HDU0DWHULDODQG:RUNPDQVKLS
0HULWRU:DEFR$%6%UDNH6\VWHP
Limited Warranty
Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

The Meritor Wabco ABS brake system shall be covered by
Meritor Wabco as indicated in the attached Meritor Wabco warranty coverage description
/,0,7(':$55$17<
(b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce.

Three (3) Year Warranty Period
Ends After:

The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

The exclusions listed in the attached Meritor Wabco warranty description shall apply.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4
(;&/86,212)&216(48(17,$/$1',1&,'(17$/'$0$*(6
Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE
POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.
%8<(5
6(;&/86,9(5(0('<
Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 2/25/2013 WA0232
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES

ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.
',6&/$,0(562):$55$17,(6
capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.

Page 212 ends

Item # 9.

WARRANTY
Warranty coverage is essential to protecting your investment. But understanding the full details of your coverage can be challenging. This straightforward approach allows you, our valued customer, to better understand how your specific vehicle applications will be covered in your region. Our component warranty coverage is provided according to vocation/usage categories listed below. • Linehaul covers high mileage operation (over 60,000 miles/year) on well-maintained major highways of concrete or asphalt construction.
• General Service covers moderate mileage operations (less than 60,000 miles/year) on well-maintained public roads (less than 10 percent off-road) typically with less than three (3) stops per mile. • Heavy Service (Vocational) covers vehicles with more than 10 percent off-road OR moderate to frequent starts/stops typically with more than three (3) stops per mile.
• Off-Highway Service covers lower mileage operations. Vehicles are not typically licensed for highway use. • The standard aftermarket warranty for WABCO products - including WABCO Original parts, WABCO Reman Solutions, ProVia quality aftermarket parts and WABCO retrofit solutions - is one year, parts only from in-service date when purchased from ZF distributor networks or its affiliates and/or subsidiaries.

MODEL YEAR 2021 VEHICLES
How to Read Warranty Coverage (Example)
Number of Years Mileage (in thousands) Unl=Unlimited P=Parts Only P&L=Parts & Labor 3 300 P

Page 213 ends

Item # 9.

WARRANTY - MODEL YEAR 2021 VEHICLES
¹ ZF and WABCO branded components. 2
WABCO compressors installed on Cummins, Mercedes, and DDC engines are not warranted or serviced by ZF. Please contact your respective dealer/distributor of those engines for warranty and servicing. 3 An extended warranty of 4/400/P will apply when a WABCO Trailer Control Line Filter is used in combination with a WABCO Trailer ABS valve.
• Aerial Ladder Truck
• Aerial Platform
• Ambulance
• Auto Hauler
• Beverage Truck
• Bulk Hauler
• Chip Hauler (Truck)
• Cross Country Coach
• Doubles
• Flatbed
• Front Engine Commercial
Chassis
• Front Engine Integral
Coach
• General Freight
• Grain Hauler
• Intercity Coach
• Intermodal Chassis
• Livestock Hauler
• Meat Packer
• Moving Van
• Municipal Truck
• Pipe Hauler
• Platform Auto Hauler
• Pumper
• Rear Engine Integral Coach
• Recreational Vehicles
• Refrigerated Freight
• School Bus
• Stake Truck
• Tanker
• Tanker Truck
• Triples
• Tour Bus
• Wrecker

LINEHAUL/GENERAL SERVICE VEHICLES

LINEHAUL/GENERAL SERVICE WARRANTY INFORMATION

LINEHAUL TYPICALLY IS
• High mileage operation (over 60,000 miles/year)
• Well maintained major highways of concrete or
asphalt construction

GENERAL SERVICE TYPICALLY IS
• Moderate mileage operations (less than 60,000 miles/year) • Well maintained public roads (less than 10% off-road) • Less than three (3) stops per mile
WABCO Components1
Air Management
Air Brake Valves
Trailer Lift Axle Control Valve 1/100/P&L
Trailer Control Line Filter3
Air Compressors (ALL)2 2/200/P&L
Air Dryers (ALL) 3/300/P&L
Aerodynamics
OptiFlow® TrailerSkirt 2/UnU/P
OptiFlow® Trailer Tail and AutoTail 2/UnI/P
Braking Systems
ABS (Anti-Lock Braking System) Air
3/300/P&L
ABS (Anti-Lock Braking System) Hydraulic
Electronic Braking System (EBS)
Electronic Stability Control (ESC)
Roll Stability Control (RSS)
Trailer Roll Stability Support (RSS)
Trailer ABS (Anti-Lock Braking System)3
Driveline Suspension Control
Clutch Controls 2/200/P&L
Leveling Valves
1/100/P&L
OptiRide® Automated Manual Transmission (AMT)
OptiRide® Electronically Controlled Air Suspension
(ECAS) 3/300/P&L
WABCO Components1 (cont.)
Safety
OnGuardACTIVE®
3/300/P&L
OnLane®
OnLaneALERT®
OnSide®
Trailer SafeStart™
Trailer TailGUARD™
Telematics
TrailerCAST™ Telematics Device 3/300/P&L
Wheel End Solutions
EasyFit™ Slack Adjuster 6/600/P
MAXXUS™ Truck Air Disc Brake 5/500/P&L
IVTM - Wheel Module 6/P
IVTM - All Other Products 2/P
Pan 17 and 19 Air Disc Brake 2/Unl/P and
1/Unl/L
Pan 22 Air Disc Brake 5/500/P and 1/L
TRISTOP™ D Actuator w/ IBV or IRB 6/600/P
TRISTOP™ D Actuator 3/300/P
UNISTOP™ Actuator 2/200/P
Trailer MAXX22T™ Air Disc Brake 5/500/P and 1/L

Page 214 ends

Item # 9.
1 ZF and WABCO branded components. 2 WABCO compressors installed on Cummins, Mercedes, and DDC engines are not warranted or serviced by ZF. Please contact your respective dealer/distributor of those engines for warranty and servicing. 3 An extended warranty of 4/400/P will apply when a WABCO Trailer Control Line Filter is used in combination with a WABCO Trailer ABS valve.

WABCO Components1
Air Management
Air Brake Valves
1/100/P&L Air Compressors (ALL)2
Air Dryers (ALL)
Trailer Control Line Filter3
Braking Systems
ABS (Anti-Lock Braking System) Air 3/300/P&L
ABS (Anti-Lock Braking System) Hydraulic 2/200/P&L
Electronic Braking System (EBS)
3/300/P&L
Electronic Stability Control (ESC)
Trailer ABS Valve3
Roll Stability Control (RSS)
Trailer Roll Stability Support (RSS)
Driveline Suspension Control
OptiRide® Electronically Controlled Air Suspension
(ECAS) 2/200/P&L
Leveling Valves 1/100/P&L
Clutch Controls 2/200/P&L
Safety
OnGuardACTIVE®
3/300/P&L
OnLane®
OnLaneALERT®
OnSide®
Trailer SafeStart™
Trailer TailGUARD™
Telematics
TrailerCAST™ Telematics Device 3/300/P&L
Wheel End Solutions
EasyFit™ Slack Adjuster 2/200/P
MAXXUS™ Air Disc Brake 1/Unl/P&L
IVTM - Wheel Module 6/P
IVTM - All Other Products 2/P
Pan 22, 19 and 17 Air Disc Brake 1/Unl/P&L
Trailer MAXX22T™ 1/Unl/P&L
TRISTOP™ D Actuator w/ IBV 3/Unl/P
TRISTOP™ D Actuator 2/200/P
UNISTOP™ Actuator 1/100/P
• Airport Rescue Fire (ARF)
• Airport Shuttle
• Asphalt Truck
• Block Truck
• Bottom Dump Trailer
Combination
• Cementing Vehicle
• City Bus
• Commercial Pick-Up
• Concrete Pumper
• Construction Material Hauler
• Crash Fire Rescue (CFR)
• Mixer
• Demolition
• Drill Rig
• Dump
• Emergency Service
• Equipment Hauling
• Flatbed Trailer Hauler
• Flatbed Truck
• Fracturing Truck
• Front Loader
• Geophysical Exploration
• Hopper Trailer Combinations
• Landscaping Truck
• Liquid Waste Hauler
• Log Hauling
• Lowboy
• Michigan Special
Gravel Trains
• Michigan Special
Log Hauler
• Michigan Special
Steel Hauler
• Michigan Special
Waste Vehicle
• Municipal Dump
• Newspaper Delivery
• Package Delivery
• Pick-up and Delivery
• Rapid Intervention
Vehicle (RIV)
• Rear Loader
• Recycling Truck
• Residential Pick-Up/Waste
• Rigging Truck
• Roll-Off
• Scrap Truck
• Semi-End Dump
• Sewer/Septic Vacuum
• Shuttle Bus
• Side Loader
• Snowplow/Snowblower
• Steel Hauling
• Tanker
• Tank Truck
• Tractors with Pole Trailers
• Tractor/Trailer with Jeeps
• Transfer Dump
• Transfer Vehicle
• Transit Bus
• Trolley
• Utility Truck
• Winch Truck

HEAVY SERVICE VEHICLES

HEAVY SERVICE (VOCATIONAL) WARRANTY INFORMATION

HEAVY SERVICE TYPICALLY IS
• On/Off road vocations (10% or more off-road) OR
• Moderate to frequent starts/stops typically more than three (3) stops per mile

Page 215 ends

Item # 9.

WARRANTY - MODEL YEAR 2021 VEHICLES

INDUSTRIAL AND OFF-HIGHWAY SERVICE

TYPICALLY IS
• Low mileage operation3
• Vehicles are not typically licensed for highway use
¹ ZF and WABCO branded components. 2 WABCO compressors installed on Cummins, Mercedes, and DDC engines are not warranted or serviced by ZF. Please contact your respective dealer/distributor of those engines for warranty and servicing. 3 Equivalent hours of service limit: 2,000 hours for all components.

INDUSTRIAL/OFF-HIGHWAY SERVICE WARRANTY INFORMATION
WABCO Components1
Air Management
Air Brake Valves
Air Compressors (ALL)2 2/Unl/P
Air Dryers (ALL)
Brake Actuation
Air/Hydraulic Actuators
2/Unl/P
Master Cylinders
Remote Actuators
Slave and Wheel Cylinders
Two Fluid Actuators
Brake Locks
Brake Locks (ALL)
Electric Brake Locks 2/Unl/P
Lever Locks
Braking Systems
ABS (Anti-Lock Braking System) Air 1/100/P&L
ABS (Anti-Lock Braking System) Hydraulic
Driveline Suspension Control
Clutch Controls
1/100/P&L
Leveling Valves
Electrohydraulics & Controls
Electronic Pedals
Electrohydraulic Brake Valves (EBV) 2/Unl/P
Pressure Switches
Hydraulic Braking Solutions
Accumulator Charging Valves
Hydraulic Throttle Controls and Switches 2/Unl/P
Modulating Brake Valves
Wheel End Solutions
EasyFit™ Slack Adjuster 2/200/P
Caliper Disc Brakes 2/Unl/P
MAXXUS™ Air Disc Brake 1/Unl/P&L
Multiple Disc Brakes 2/Unl/P
IVTM - Wheel Module 6/P
IVTM - All Other Products 2/P
Pan 22, 19 and 17 Air Disc Brake 1/Unl/P&L
TRISTOP™ D Actuator w/ IBV 3/Unl/P
TRISTOP™ D Actuator 2/200/P
UNISTOP™ Actuator 1/100/P
Market Common Application Types
Agriculture
Fertilizer Spreader, Tractor, Heavy Duty Ag
Trailers, Harvester, Sprayer, Skid Loader, Silage
Bagger, Slurry Wagons, Grain Cart
Airport Support
Pushback Tractor, Towing Tugs, Aircraft Tow
Tractor, Refueling Trucks, Food Service Trucks,
Baggage Tractors, De-Icing Equipment,
Runway Clearing Equipment
Construction
All-Terrain Crane, Rough Terrain Crane,
Excavator, Compactor, Wheel Loader, Road
Roller, Motor Grader, Articulated Dump Truck,
Rubber Tire Road Roller, Backhoe Loaders,
Haul Trucks, Scraper Rough Terrain Forklifts,
Trenchers, Drills
Forestry Logging Forwarder, Kidder, Loaders, Yard
Forklifts, Harvesters Fellers
Material Handling
Port Tractor, Rail Yard Spotter, Stevedoring
Tractor, Trailer Spotter, Yard Jockey, Scissor
Lift, Straddle Carrier, Manlift, Forklift, Boom Lift
Telebandlers, Aerial Work Platforms
Mining
Specialized Mining, Excavator, Haul Truck,
Underground Loader, Service Trucks, Wheel
Loaders, Scrapers, Load Haul Dumps,
Personnel Transports, Bolters, Scalers
Municipal
Street Sweeper, Utility Tractor, Utility Trucks,
Tree Trimmers, Dump Trucks, Tow Trucks, Flat
Bed Trucks, Winch Applications
Oil & Gas
Fracturing Trailer, Injecter Heads, Top Drives,
Jack/Lift Boats, Wireline Trucks, Load-On /
Load-Off
Rail
Railcar Mover, Track Layers, Grinders, Platform
Crane, Locomotive Railcars, Ballast Equipment,
Winch Applications

Page 216 ends

Item # 9.

ABS, ELECTRONIC STABILITY CONTROL (ESC),
ROLL STABILITY CONTROL (RSC), OPTIRIDE®,
ONGUARD® AND ONLANE®, COLLECTIVELY
“ELECTRONICS”
Failure of electronic components due to overvoltage
condition, improper grounding, electrostatic discharge
(ESD), improper shielding, electromagnetic interference (EMI), or other wiring or installation issues. Malfunctions and failure codes caused by other electronic subsystem failures (data bus, engine, transmission, dashboard, etc.)

HYDRAULIC COMPONENTS
For certain components, brake fluid DOT3 or DOT4 is
used as the operating medium. Use of any other fluid will void all warranties associated with that component. For hydraulic braking applications the brake fluid is considered a maintenance item. Maintenance intervals are listed in TB1367.

COVERAGE LIMITATIONS

PRODUCT DESCRIPTION

ALL PRODUCTS
Any claim beyond 60 days from date of repair will not be accepted or honored under this warranty program.

Products purchased on an incomplete vehicle (glider) are limited to one year, 1/Unl/P.

For vehicles that operate full- or part-time outside of the United States and Canada, a 1-Year/Unlimited Miles parts only (1/Unl/P) will apply.

TOOLBOX PLUS™ DIAGNOSTIC SOFTWARE
Proper diagnostics of WABCO Electronics may require the latest version of TOOLBOX PLUS™. Additional labor due
to use of an outdated version of TOOLBOX™ software
and/or the time to purchase or install the latest version of TOOLBOX PLUS™ are not covered under product
warranty.

TERMS AND CONDITIONS

COVERAGE EXCLUSIONS

PRODUCT DESCRIPTION

ALL PRODUCTS
This Warranty shall not apply to the following, but not limited to: (1) damage to the product or its component
parts caused by incorrect use, installation, maintenance or repair, including without limitation (a) improper fit of mating components or brackets, damaged threads, cut, broken,
chafed, pinched or otherwise damaged wiring (sensors,
harnesses and connectors), (b) sensors damaged during
removal when seized in block, or associated with sensor adjustments/ alignments, and (c) damage resulting from the use or installation of non-genuine WABCO components or
materials; (2) damage to the product, its component parts, or diminished product or component part performance due to incorrect operation, deviation from approved conditions or misapplication; (3) any unauthorized disassembly of the product or its component parts including without limitation (a) obliterated, defaced or missing WABCO or WABCO
name plate, serial numbers or label identifying the device as a ZF product or WABCO component, (b) changes to sealed
adjusting screws, and (c) opening or attempted repair of non-serviceable components; (4) malfunction
of the component due to internal contamination of the
vehicle system including without limitation (a) water and other contamination damage that is due to the use of a
non-genuine air dryer cartridge or (b) valve failures due to contamination in air system, (5) complaints associated
with noise, (6) damage resulting from corrosion (including oxidation of electrical devices and connections).

AIR DRYERS
Mounting brackets (see vehicle OEM). Desiccant cartridge housing only.

AIR SYSTEM COMPONENTS
Normal wear items; Gladhand seals, dash valve knobs,
valve actuation handles, treadles, pedals.

Page 217 ends

Item # 9.

WARRANTY - MODEL YEAR 2021 VEHICLES
(1) What is Covered by this Commercial Warranty?
ZF CV Systems North America LLC and its North American
subsidiaries and affiliates (ZF) warrant to the owner (“Owner”) that the components listed in this publication, which have been installed by an Original Equipment Manufacturer (“OEM”) as original equipment will be free from defects in material and workmanship. This warranty coverage begins from the original in-service date to the limits provided and runs concurrently with any warranties provided by OEMs and/or any distribution agreements and/or any service contracts that cover the components listed in this publication, if any. If the components listed in this publication are covered by an OEM warranty and/or service contract, then the OEM’s warranty and/ or service contract shall supersede ZF’s warranty and Owner shall comply with all OEM’s warranty and/or service contract requirements for claims under such OEM’s warranty and/or service contract until those agreements expire.

Once those agreements expire and provided the ZF warranty has not expired under the terms stated above, the ZF warranty will be in effect until its expiration date.

Warranty coverage ends at the expiration of the applicable time period from the date of vehicle purchase by the first Owner, or, the applicable mileage limitation, whichever occurs first. Duration of coverage varies by component and vocation as detailed previously in this publication.

Some components are warranted for parts only and the Owner must pay any labor costs associated with the repair or replacement of the component. Other components are warranted for both parts and reasonable labor to repair or replace the subject component.

Additional diagnostic time due to use of an outdated version of TOOLBOX™, time to purchase or install latest version of TOOLBOX™ are the responsibility of the authorized ZF distributor networks and are not covered under product warranty. Components installed as replacements under this warranty are warranted only for the remainder of the original period of time or mileage under the original warranty. (2) Designation of Vocational Use Required. To obtain warranty coverage, each Owner must notify ZF through the OEM new truck and/or trailer dealer of the intended vocational use of the vehicle into which the WABCO components have been incorporated prior to the vehicle inservice date. This notification may be accomplished by registering the vehicle through your OEM new truck and/or trailer dealer or with ZF directly. Failure to notify ZF of (I) the intended vocational use of the vehicle or (II) a change in vocational use from that which was originally designated, will result in the application of a one year, unlimited mileage, parts only warranty (1/Unl/P) from the initial inservice date. A second Owner and each subsequent Owner must also notify ZF as to the intended vocational use of the vehicle. This notification can be sent directly to ZF or through
the OEM new truck and/or trailer dealer. The duration and mileage coverage of this warranty cannot exceed the coverage extended to the first Owner after his or her initial designation of vocational use. Coverage under ZF’s warranty requires that the application of products be properly approved pursuant to OEM and ZF, approvals. (3) What is the Cost of this Warranty? There is no charge to the Owner for this warranty.
(4) What is not Covered by this Warranty? In addition to the items listed on "Coverage Exclusions," this warranty does not cover normal wear and tear, or service items; nor does it cover a component that fails, malfunctions or is damaged as a result of (a) improper handling, storage, installation, adjustment, repair or modification including the use of unauthorized attachments or changes or modification in the vehicle’s configuration, usage, or vocation from that which was originally approved by ZF, (b) accident, fire or other casualty, natural disaster, road debris, negligence, misuse, abuse, or improper use (including loading beyond the specified maximum vehicle weight or altering engine power settings to exceed the brake system capacity), or (c) improper or insufficient maintenance (including deviation from maintenance intervals, approved lubricants, or lube levels). This warranty does not cover any component or part that is not sold by ZF. (5) To obtain service. If the owner discovers within the applicable coverage period a defect in material or workmanship, the Owner must promptly give notice to either ZF or the dealer from which the vehicle was purchased. To obtain service, the vehicle must be taken to any participating OEM dealer or ZF distributor networks' servicer. The dealer or ZF authorized servicer will inspect the vehicle and contact ZF for an evaluation of the claim. When authorized by ZF, the dealer or ZF authorized servicer will repair or replace during the term of this warranty any defective WABCO component covered by this warranty. (6) Disclaimer of Warranty and Limitation of remedies. TO THE MAXIMUM

EXTENT PERMITTED BY LAW, THE LIMITED WARRANTY SET

FORTH HEREIN IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER

WARRANTIES, EXPRESS OR IMPLIED, ARISING BY OPERATION OF

LAW OR OTHERWISE, INCLUDING, WITHOUT LIMITATION, ANY

IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE AND/OR WARRANTY FOR HIDDEN OR

LATENT DEFECTS, AND IN NO EVENT WILL ZF OR ANY OF ITS

AFFILIATES BE LIABLE FOR DIRECT, INDIRECT, INCIDENTAL,

PROGRESSIVE, SPECIAL, OR CONSEQUENTIAL DAMAGES OF ANY
KIND.

TERMS AND CONDITIONS

Page 218 ends

Item # 9.
(7) Legal action. Any legal action or claim arising from or related to this Warranty, in contract or otherwise, must be commenced within one year from the accrual of that cause of action, or be barred forever. Any dispute arising in connection with this agreement shall be governed by and construed according to the laws of the State of Michigan and be brought, heard and determined exclusively in either the Circuit Court for the County of Oakland, State of Michigan or the United States District Court for the Eastern District of Michigan. The parties stipulate that the referenced venues are convenient.
(8) Remedy. The exclusive remedy under this warranty shall be the repair or replacement of the defective component at ZF's option. ZF reserves the right to require that all applicable covered components are available and/or returned to ZF for review
and evaluation. THE MAXIMUM LIABILITY, IF ANY, OF ZF FOR ALL

DAMAGES, INCLUDING WITHOUT LIMITATION CONTRACT

DAMAGES, BREACH OF WARRANTY, NEGLIGENCE, STRICT

LIABILITY, OR OTHER TORT, IS LIMITED TO AN AMOUNT NOT TO EXCEED THE PURCHASE PRICE OF THE PRODUCT and where
indicated in the product and application warranty information above, the inclusion of labor is limited to the standard repair time. THE

PARTIES ACKNOWLEDGE AND AGREE THAT THE LIMITATION

OF DAMAGES PROVISION SET FORTH IN THIS PARAGRAPH

SURVIVES BETWEEN THE ORIGINAL END USER AND ZF EVEN IF

THE EXCLUSIVE REMEDY SET FORTH ABOVE IS DEEMED TO FAIL
OF ITS ESSENTIAL PURPOSE. ZF may change the design or make improvements to its Products without incurring any warranty obligation for previously manufactured Product .
(9) Entire Agreement. This is the entire agreement between ZF and the Owner about warranty and no, ZF employee, or dealer is authorized to make any additional warranty on behalf of ZF unless in writing and signed by an authorized representative of ZF.

Page 219 ends

Item # 9.

About ZF Friedrichshafen AG
ZF is a global technology company and supplies systems for passenger cars, commercial vehicles and industrial technology, enabling the next generation of mobility. ZF allows vehicles to see, think and act. In the four technology domains Vehicle Motion Control, Integrated Safety, Automated Driving, and Electric Mobility, ZF offers comprehensive solutions for established vehicle manufacturers and newly emerging transport and mobility service providers. ZF electrifies different kinds of vehicles. With its products, the company contributes to reducing emissions and protecting the climate.

ZF, which acquired WABCO Holdings Inc. on May 29, 2020, now has 160,000 employees worldwide with approximately 260 locations in 41 countries. In 2019, the two then-independent companies achieved sales of €36.5 billion (ZF) and $3.4 billion (WABCO). For more information, visit: www.wabco-na.com
© 2021 ZF CV Systems North America LLC - All rights reserved - SP1375 / 2.2021 For further product details contact your distributor or the WABCO Customer Care Center at 855-228-3203.

Page 220 ends

Item # 9.

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This warranty applies only to the cab tubular support and mounting structures and other structural components of the cab of the vehicle model, as identified in the Pierce
specifications for the Fire and Rescue Apparatus.

This warranty does not apply to damage caused by corrosion.

Conditions and
Exclusions:

Fire and Rescue Apparatus
Coverage:

Ten (10) Year Structural Integrity
Custom Cab
Ten (10) Years
- or -
100,000 Miles
Warranty Period
Ends After:

The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:

The Pierce Custom Cab shall be free from structural failures caused by defects in material and workmanship
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

3. BUYER'S EXCLUSIVE REMEDY.

Page 221 ends

Item # 9.

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

3. BUYER'S EXCLUSIVE REMEDY.

Fire and Rescue Apparatus
Coverage:

Ten (10) Year Pro-Rated Paint and Corrosion
Cab
Ten (10) Years Warranty Period
Ends After:

The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:

Exterior surfaces of the cab painted by Pierce shall be free from blistering, peeling, corrosion or any other adhesion defect caused by defective manufacturing methods or paint material selection.
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This limited warranty is applicable to the vehicle in the following percentage costs of warranty repair, if any:

Topcoat Durability & Appearance: Gloss, Color Retention & Cracking
0-72 months 100%
73-96 months 50%
97-120 months 25%
Integrity of Coating System: Adhesion, Blistering/Bubbling 0-36 months 100%
37-84 months 50%
85-120 months 25%
Corrosion: Dissimilar Metal and Crevice
0-36 months 100%
37-48 months 50%
49-72 months 25%
73-120 months 10%
Corrosion Perforation
0-120 months 100%
This limited warranty applies only to exterior paint. Paint on the vehicle's interior is warranted only under the Pierce Basic One Year Limited Warranty.

Items not covered by this warranty include:
(a) Damage from lack of maintenance and cleaning (proper cleaning and maintenance procedures are detailed in the Pierce operation and maintenance manual).
(b) UV paint fade.
(c) Any cab not manufactured by Pierce.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4

Page 222 ends

Item # 9.

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This limited warranty applies to all of the control modules for the Command Zone system, including the full color graphic displays. Related wire harnesses, cables and connectors are not covered under this limited warranty and are instead covered under the Pierce One Year Basic Apparatus Limited Warranty.

Conditions and
Exclusions:

Fire and Rescue Apparatus
Coverage:

Five (5) Year Material and Workmanship
Command Zone Electronics
Five (5) Years Warranty Period
Ends After:

The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:

Command Zone control modules shall be free from failures caused by defects in material and workmanship
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

3. BUYER'S EXCLUSIVE REMEDY.

Page 223 ends

Item # 9.

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This limited warranty does not apply to related wire
harnesses, cables, and connectors, which are covered by the Pierce one (1) year basic apparatus limited warranty.

Conditions and
Exclusions:

Fire and Rescue Apparatus
Coverage:
54 Months Material and Workmanship
Camera System
Fifty - Four (54) months Warranty Period
Ends After:

Warranty Begins: The date of delivery.

This limited warranty covers repairs to correct any defect related to materials or workmanship of the Sharpvision
camera system installed on the apparatus occuring during the warranty period.
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

3. BUYER'S EXCLUSIVE REMEDY.

Page 224 ends

Item # 9.

NEW PRODUCT WARRANTY

PARTICIPATING OEM SALES

DISTRIBUTOR SALES

LIMITED WARRANTY ON NEW ALLISON AUTOMATIC TRANSMISSIONS

USED IN EMERGENCY VEHICLE APPLICATIONS
Allison Transmission will provide for repairs or replacement, at its option, during the warranty period of each new Allison transmission listed below that is installed in an Emergency Vehicle in accordance with the following terms, conditions, and limitations.

WHAT IS COVERED
 WARRANTY APPLIES — This warranty is for new Allison transmission models listed below installed in an Emergency Vehicle and is provided to the original and any subsequent owner(s) of the vehicle during the warranty period.  REPAIRS COVERED — The warranty covers repairs or replacement, at Allison Transmission’s option, to correct any transmission malfunction resulting from defects in material or workmanship occurring during the warranty period. Needed repairs or replacements will be performed using the method Allison Transmission determines most appropriate under the circumstances.  TOWING — Towing is covered to the nearest Allison Transmission Distributor or authorized Dealer only when necessary to prevent further damage to your transmission.
 PAYMENT TERMS — Warranty repairs, including parts and labor, will be covered per the schedule shown in the chart contained in section “APPLICABLE MODELS, WARRANTY LIMITATIONS, AND ADJUSTMENT SCHEDULE.”  OBTAINING REPAIRS — To obtain warranty repairs, take the vehicle to any Allison Transmission Distributor or authorized Dealer within a reasonable amount of time and request the needed repairs. A reasonable amount of time must be allowed for the Distributor or Dealer to perform necessary repairs.
 TRANSMISSION REMOVAL AND REINSTALLATION — Labor costs for the removal and re-installation of the transmission, when necessary to make a warranty repair, are covered by this warranty.  WARRANTY PERIOD — The warranty period for all coverages shall begin on the date the transmission is delivered to the first retail purchaser, with the following exception:

Demonstration Service - A transmission in a new truck or bus may be demonstrated to a total of 5000 miles (8000 kilometers).

If the vehicle is within this limit when sold to a retail purchaser, the warranty start date is the date of purchase. Normal warranty services are applicable to the demonstrating Dealer. Should the truck or bus be sold to a retail purchaser after these limits are reached, the warranty period will begin on the date the vehicle was first placed in demonstration service and the purchaser will be entitled to the remaining warranty.

APPLICABLE MODELS, WARRANTY LIMITATIONS, AND ADJUSTMENT SCHEDULE

WARRANTY LIMITATIONS
(Whichever occurs first)

ADJUSTMENT CHARGE TO BE

APPLICABLE PAID BY THE CUSTOMER
MODELS
Months
Transmission Miles
Or Kilometers Parts Labor
MT, MD
3000, 3200, 3500, 3700 0–24 No Limit No Charge No Charge HT with Hydraulic Controls 0–24 No Limit No Charge No Charge AT, 1000 Series, 2000 Series,
2400 Series 0–36 No Limit No Charge No Charge
HT with Electronic Controls 0–60 No Limit No Charge No Charge HD
1000 EVS, 2100 EVS, 2200 EVS
2350 EVS, 2500 EVS, 2550 EVS,
3000 EVS, 3500 EVS, 4000,
4000 EVS, 4500, 4500 EVS, 4700,
4700 EVS, 4800, 4800 EVS
0–60 No Limit No Charge No Charge

Page 1 of 2 ends

Page 225 ends

Item # 9.

WHAT IS NOT COVERED
 DAMAGE DUE TO ACCIDENT, MISUSE, or ALTERATION — Defects and damage caused as the result of any of the following are not covered:
— Flood, collision, fire, theft, freezing, vandalism, riot, explosion, or objects striking the vehicle; — Misuse of the vehicle;
— Installation into unapproved applications and installations; — Alterations or modification of the transmission or the vehicle, and — Damage resulting from improper storage (refer to long-term storage procedure outlined in the applicable Allison Service Manual) — Anything other than defects in Allison Transmission material or workmanship NOTE: This warranty is void on transmissions used in vehicles currently or previously titled as salvaged, scrapped, junked, or totaled.  CHASSIS, BODY, and COMPONENTS — The chassis and body company (assemblers) and other component and equipment manufacturers are solely responsible for warranties on the chassis, body, component(s), and equipment they provide. Any transmission repair caused by an alteration(s) made to the Allison transmission or the vehicle which allows the transmission to be installed or operated outside of the limits defined in the appropriate Allison Installation Guideline is solely the responsibility of the entity making the alteration(s).  DAMAGE CAUSED by LACK of MAINTENANCE or by the USE of TRANSMISSION FLUIDS NOT RECOMMENDED in the OPERATOR’S MANUAL — Defects and damage caused by any of the following are not covered:
— Failure to follow the recommendations of the maintenance schedule intervals applicable to the transmission; — Failure to use transmission fluids or maintain transmission fluid levels recommended in the Operator’s Manual.  MAINTENANCE — Normal maintenance (such as replacement of filters, screens, and transmission fluid) is not covered and is the owner’s responsibility.
 REPAIRS by UNAUTHORIZED DEALERS — Defects and damage caused by a service outlet that is not an authorized Allison Transmission Distributor or Dealer are not covered.
 USE of OTHER THAN GENUINE ALLISON TRANSMISSION PARTS — Defects and damage caused by the use of parts that are not genuine Allison Transmission parts are not covered.  EXTRA EXPENSES — Economic loss and extra expenses are not covered. Examples include but are not limited to: loss of vehicle use; inconvenience; storage; payment for loss of time or pay; vehicle rental expense; lodging; meals; or other travel costs.  “DENIED PARTY” OWNERSHIP — Warranty repair parts and labor costs are not reimbursed to any participating or non-participating OEMs, dealers or distributors who perform warranty work for, or on behalf of, end users identified by the United States as being a “denied party” or who are citizens of sanctioned or embargoed countries as defined by the U.S. Department of Treasury Office of Foreign Assets Control. Furthermore, warranty reimbursements are not guaranteed if the reimbursement would be contrary to any United States export control laws or regulations as defined by the U.S. Department of Commerce, the U.S. Department of State, or the U.S. Department of Treasury.

OTHER TERMS APPLICABLE TO CONSUMERS AS DEFINED by the MAGNUSON-MOSS WARRANTY ACT This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

Allison Transmission does not authorize any person to create for it any other obligation or liability in connection with these transmissions.

ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE APPLICABLE TO THESE TRANSMISSIONS IS LIMITED IN DURATION TO THE DURATION OF THIS WRITTEN WARRANTY.

PERFORMANCE OF REPAIRS AND NEEDED ADJUSTMENTS IS THE EXCLUSIVE REMEDY UNDER THIS WRITTEN WARRANTY OR ANY IMPLIED WARRANTY. ALLISON TRANSMISSION SHALL NOT BE LIABLE FOR INCIDENTAL OR

CONSEQUENTIAL DAMAGES (SUCH AS, BUT NOT LIMITED TO, LOST WAGES OR VEHICLE RENTAL EXPENSES) RESULTING FROM BREACH OF THIS WRITTEN WARRANTY OR ANY IMPLIED WARRANTY.** ** Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you.

OTHER TERMS APPLICABLE TO OTHER END-USERS

THIS WARRANTY IS THE ONLY WARRANTY APPLICABLE TO THE ALLISON TRANSMISSION MODELS LISTED

ABOVE AND IS EXPRESSLY IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. ALLISON

TRANSMISSION DOES NOT AUTHORIZE ANY PERSON TO CREATE FOR IT ANY OTHER OBLIGATION OR LIABILITY IN CONNECTION WITH SUCH TRANSMISSIONS. ALLISON TRANSMISSION SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM BREACH OF THIS WARRANTY OR ANY IMPLIED WARRANTY.

QUESTIONS
If you have any questions regarding this warranty or the performance of warranty obligations, you may contact any Allison Transmission Distributor or Dealer or write to:

Allison Transmission, Inc.

P.O. Box 894
Indianapolis, IN 46206-0894
Attention: Warranty Administration PF-9
Form SE0616EN (201009)

Page 2 of 2 ends

Page 226 ends

Item # 9.

Warranty Begins:

The transmission cooler shall be free from component or structural failures caused by defects in material and/or workmanship. Collateral damage up to $10,000 per
occurrence is available for the first three (3) years.
(b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; (d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce.

Five (5) Years on Oil Cooler and three (3) years on collateral damage coverage
Warranty Period
Ends After:

Fire and Rescue Apparatus
Coverage:

Five (5) Year Material and Workmanship - Transmission Oil Cooler Three (3) Year Collateral Damage Coverage

1. LIMITED WARRANTY
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

The date of delivery to the first retail purchaser.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This warranty does not cover repair due to accidents,
misuse, and excessive vibration, flying debris, storage damage (freezing), negligence or modification. This warranty is void if any modification or repairs are performed without authorization. This also voids any future warranty.

This warranty does not cover cost of maintenance or repairs due to lack of required maintenance services as
recommended. Performance of the required maintenance
and use of proper fluids are the responsibility of the owner.

Towing is covered to the nearest distributor or authorized dealer only when necessary to prevent further damage to your transmission.

Labor costs for the removal and reinstallation of goods may be covered when necessary to make repairs. Please contact your OEM for authorization.

Replacement of cooler during the warranty period is limited to 100% of reasonable labor costs up to a maximum of $700 to remove, replace, or repair the oil cooler.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE
POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

3. BUYER'S EXCLUSIVE REMEDY.

ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

2. DISCLAIMERS OF WARRANTIES
capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.

Page 227 ends

Item # 9.

Limited Lifetime Warranty
Effective as of January 1, 2024

1. General. United Plastic Fabricating, Inc. (the
"Company") warrants to the owner (the “Owner”) that
the products set forth on Exhibit A, attached hereto (the "Product") will be reasonably free from defects in
materials and workmanship for the service life of the
Product. This Limited Lifetime Warranty (the
“Warranty”) only applies to Company Products that are:
(a) owned by a federal, state, county or local
government, a volunteer fire department or dedicated
commercial fire service operation; (b) continuously and actively used in emergency response and/or fire
suppression vehicles; and (c) used, stored, handled
and installed in the manner recommended by
Company.

2. Warranty Obligations. Subject to the exclusions and
limitations set forth in this Warranty, Company will, at its option, repair or offer a one (1) time replacement of the Product without charge, if the Product fails or does not perform as warranted during the warranty period due to
a manufacturing defect or a defect in materials. Repair or replacement shall include reasonable labor charges
necessary to repair or replace the defective Product but shall not include: (a) the costs associated with removal of the Product from the vehicle or the cost to otherwise provide access to the Product in the vehicle; (b) the cost associated with any required upgrades the vehicle
(including, without limitation, upgrades required to
strengthen the vehicle’s frame); or (c) travel costs,
except as provided by Section 3. Company's obligation
as to repair or replacement shall further be limited to repair or replacement with the models of the Product
that are available at the time of the repair or
replacement, and shall be limited to the repair or
replacement of only the specific Product that fails due to a manufacturing defect. In the event a Product
becomes unavailable or cannot be supplied by
Company for any reason a substitute Product of equal
quality and functionality of the subject Product may be substituted by Company. Any repaired Product shall
remain subject to this Warranty and any repair shall not extend the warranty period in any manner or start a new warranty period. Any Product that is replaced by
Company shall be excluded from this Warranty. In no
event shall Company be required to expend, in any one
(1) or series of expenditures, more than the purchase
price of the Product to repair or replace a defective
Product. Amounts expended by Company shall include
all amounts paid by Company in connection the repair
or replacement, including without limitation, amounts
paid to third-parties, material costs, incidental costs and travel costs (except as provided by Section 3).

3. Travel; Expenses; Product Access. Company shall
be responsible for any travel costs incurred to repair or replace the Product provided that: (a) the Product is
located in the continental United States or Canada; and (ii) the warranty claim is initiated prior to the date on which NFPA 1912 Standards (Annex D) recommends
replacement of the Product. All other travel costs
incurred by Company or its agents to repair or replace
the Product shall be the responsibility of the party
asserting the warranty claim. Company reserves the
right to require, as a condition to undertaking any repair or replacement: (y) pre-payment of its anticipated travel costs; and (z) satisfactory arraignments concerning
scheduling and access to the Product. If the subject
Product is located in an area of the world considered, in Company’s sole discretion, to be unsafe Company may
refuse to process the claim or require relocation of the Product, at no expense to Company, to an area where
such repairs can be performed safely by Company or
its agents. In the event Company or Company’s agents
are dispatched to repair or replace a defective Product and the vehicle in which the Product has been installed is not available or the Product is not readily accessible, for any reason, Company or Company’s agents, as the
case may be, shall be immediately reimbursed for all
expenses incurred therewith.

4. Exclusions: Products must be stored, handled,
installed, used and maintained in accordance with
instructions provided by Company, and this Warranty is
conditioned upon compliance with all such instructions.

This Warranty does not cover defects caused by: (a)
improper installation; (b) modification, alteration or
repair of the Product by any unauthorized third-party;
(c) misuse, including, without limitation, improper

Page 228 ends

Item # 9.
storage or handling of the Product (e.g. excessive
exposure to UV rays); chemical abuse (e.g. harsh
cleansers and solvents), thermal abuse or shock (e.g.
excessive heat or cold); (d) damage not resulting from
manufacturing defects that occur while the Product is
not in Company’s possession (e.g. accidents); or (e)
unreasonable or unintended use of the Product. Copies
of the Company's operation and maintenance
instructions are available on the Company's website
https://www.unitedplastic.com/upf-documents/

5. Disclaimer. THE WARRANTIES SET FORTH

HEREIN ARE THE ONLY WARRANTIES MADE BY
COMPANY IN CONNECTION WITH THE PRODUCT.

COMPANY CAN NOT AND DOES NOT MAKE ANY

IMPLIED OR EXPRESS WARRANTIES WITH

RESPECT TO THE PRODUCT, AND DISCLAIMS ALL

OTHER WARRANTIES, INCLUDING, BUT NOT

LIMITED TO, ANY WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. PRODUCTS SOLD BY

COMPANY ARE SOLD ONLY TO THE

SPECIFICATIONS SPECIFICALLY SET FORTH BY
COMPANY IN WRITING. OTHER THAN THE LIMITED

WARRANTY SET FORTH HEREIN, COMPANY

MAKES NO OTHER WARRANTIES, EXPRESS OR
IMPLIED. COMPANY'S SOLE OBLIGATION UNDER

THIS WARRANTY SHALL BE REPAIR OR
REPLACEMENT OF NON-CONFORMING PRODUCT.

BUYER ASSUMES ALL RISK WHATSOEVER AS TO

THE RESULT OF THE USE OF THE PRODUCT

PURCHASED, WHETHER USED SINGULARLY OR IN

COMBINATION WITH ANY OTHER PRODUCTS OR
SUBSTANCES.

6. Limitation of Liability. NO CLAIM BY OWNER OF

ANY KIND, INCLUDING CLAIMS FOR

INDEMNIFICATION, SHALL BE GREATER IN

AMOUNT THAN THE PURCHASE PRICE OF THE

PRODUCT IN RESPECT TO WHICH DAMAGES ARE
CLAIMED. IN NO EVENT SHALL COMPANY BE

LIABLE TO OWNER IN TORT, CONTRACT OR

OTHERWISE, FOR ANY SPECIAL, INDIRECT,

INCIDENTAL, CONSEQUENTIAL (INCLUDING,

WITHOUT LIMITATION, ANY OBLIGATION OF

COMPANY TO REPAIR OR REPLACE ANY

CHASSIS, SUB-FRAMES, BODIES, VALVES,

DUMPS, HOSES, PRESSURE VACUUM VENTS OR

OTHER SIMILAR COMPONENTS), RELIANCE,

STATUTORY, SPECIAL, PUNITIVE OR EXEMPLARY

DAMAGES, INCLUDING, BUT NOT LIMITED TO,

LOST PROFITS, LOSS OF USE, LOSS OF TIME,

LOSS OF REVENUES, INCONVENIENCE, LOSS

BUSINESS OPPORTUNITIES, OR DAMAGE TO

GOOD WILL OR REPUTATION, EVEN IF ADVISED

OF THE POSSIBILITY OF SUCH DAMAGES OR

SUCH DAMAGES COULD HAVE BEEN

REASONABLY FORESEEN, IN CONNECTION WITH,

ARISING OUT OF, OR AS A RESULT OF, THE SALE,

DELIVERY, SERVICING, USE OR LOSS OF USE OF

THE PRODUCTS SOLD HEREUNDER, OR FOR ANY

LIABILITY OF BUYER TO ANY THIRD PARTY WITH
RESPECT THERETO.

7. Reformation. If any term or provision of this Warranty shall be held or deemed to be, or shall in fact be, invalid, inoperative, illegal or unenforceable as applied in any case or in any jurisdiction or jurisdictions because of the conflicting nature of any provision with any constitution or statute or rule of public policy or for any other reason, then: (a) such circumstance shall not have the effect of rendering the provision or provisions in question invalid, inoperative, illegal or unenforceable in any other
jurisdiction or in any other case or circumstance or of rendering any other provision or provisions herein
contained invalid, inoperative, illegal or unenforceable to the extent that such other provisions are not
themselves actually in conflict with such constitution, statute or rule of public policy; and (b) any such
invalid, inoperative, illegal or unenforceable provision shall be reformed and construed in any such jurisdiction or case so that such provision would be valid, operative and enforceable to the maximum extent permitted in
such jurisdiction or case.

8. Headings. The headings contained herein are for
convenience and reference only, and shall be given no
effect in the interpretation of any term or condition of this Warranty.

9. Submitting a Warranty Claim. To request coverage
under this Warranty you must submit a claim through
Company’s_website:
https://www.unitedplastic.com/contact/product-support/

10. Transferability. This Warranty is transferable and
entitles the transferee to coverage for the remainder of the original warranty period.

11. Modification. This Warranty may be modified (a) as
set forth on a binding sales order for the Product or (b) by a written agreement between Company and the
Owner.

Page 229 ends

Item # 9.

Exhibit A
Covered Product List
 Poly-Tanks®
 PolySide® Wetside Tanks
 Defender™ Skid Tanks
 Ellip-T™ Elliptical Tanks
 ARFF Tanks

Page 230 ends

Item # 9.

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This warranty applies only to the body tubular support and mounting structures and other structural components of the body of the vehicle model, as identified in the Pierce
specifications for the Fire and Rescue Apparatus.

This warranty does not apply to damage caused by corrosion.

Conditions and
Exclusions:

Fire and Rescue Apparatus
Coverage:

Ten (10) Year Structural Integrity
Apparatus Body
Ten (10) Years
- or -
100,000 Miles
Warranty Period
Ends After:

The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:

The apparatus body shall be free from structural failures caused by defects in material and workmanship
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

3. BUYER'S EXCLUSIVE REMEDY.

Page 231 ends

Item # 9.

A & A Manufacturing Co., Inc. 2300 S. Calhoun Road · New Berlin, WI 53151 · Phone (262) 786-1500 · Fax (262) 786-3280 Pierce Warranty Statement for Gortite Roll Up Doors Rev 2/24/2011 All mechanical components of the door shall be warranted to be free from defects in materials and workmanship for the lifetime of the vehicle. All parts covered under this warranty shall be to the original owner.

A&A manufacturing warrants that painted doors shall be free of blistering, peeling, bubbling, or any other adhesion defect caused by defective manufacturing methods or paint material selection. The time period for the coverage shall be 6 years from date of door shipment to Pierce. Satin anodized finish doors shall be warranted for 6 years against corrosion defects from date of door shipment to Pierce. Replacement of decals/Scotchlite is not covered.

The maximum amount A&A will reimburse for labor is $60.00 per hour and the maximum amount of time allowed for repair is as follows:

Door 1.0 Hr.

Slat Replacement 1.0 Hr.

Pennant Plate Replacement 1.0 Hr.

Roller Replacement .5 Hr.

Seal Replacement .5 Hr.

Switch/Magnet Replacement 1.0 Hr.

Travel Time 4.0 Hr.

Page 232 ends

Item # 9.

Waterous Company
125 Hardman Avenue South
South St. Paul, MN 55075 USA
www.waterousco.com
F-2891 (04/15/20)
Waterous Seven-Year Limited Warranty
WATEROUS warrants, to the original Buyer only, that products manufactured by WATEROUS will be free from defects in material and workmanship under normal use and service for a period of seven (7) years from the date the product is first placed in service, or seven and one-half (7-1/2) years from the date of shipment by WATEROUS, whichever period shall be the first to expire; provided the Buyer notifies WATEROUS, in writing, of the defect in said product within the warranty period, and said product is found by WATEROUS to be nonconforming with the aforesaid warranty. When required in writing by WATEROUS, defective products must be promptly returned by Buyer to WATEROUS at WATEROUS’ plant at South St. Paul, Minnesota, or at such other place as may be specified by WATEROUS, with transportation and other charges prepaid. A Returned Material Authorization (RMA) is required for all products and parts and may be requested by phone, fax, email, or mail. The aforesaid warranty excludes any responsibility or liability of WATEROUS for:
(a) damages or defects due to accident, abuse, misuse, abnormal operating conditions, negligence, accidental causes, use in non-firefighting applications, or improper maintenance, or attributable to written specifications or instructions furnished by Buyer; (b) defects in products manufactured by others and furnished by WATEROUS hereunder, it being understood and agreed by the parties that the only warranty provided for such products shall be the warranty provided by the manufacturer thereof which, if assignable, WATEROUS will assign to Buyer, if requested by Buyer;
(c) any product or part, altered, modified, serviced or repaired other than by WATEROUS, without its prior written consent; (d) the cost of dismantling, removing, transporting, storing, or insuring the defective product or part and the cost of reinstallation; and (e) normal wear items (packing, strainers, filters, light bulbs, anodes, intake screens, mechanical seals, etc.).

ALL OTHER WARRANTIES ARE EXCLUDED, WHETHER EXPRESS OR IMPLIED BY OPERATION OF LAW OR OTHERWISE, INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT, WHETHER AS A RESULT OF BREACH OF

CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE), STRICT LIABILITY, OR ANY OTHER CAUSE OF ACTION, SHALL WATEROUS BE LIABLE FOR ANY PUNITIVE, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR FOR PERSONAL INJURY OR PROPERTY DAMAGES.

The exclusive remedy of Buyer and the sole liability of WATEROUS, whether based on contract, warranty, tort or any other basis of recovery whatsoever, is expressly limited at the election of WATEROUS to:
(a) the replacement at the agreed point of delivery of any product or part, which upon inspection by WATEROUS or its duly authorized representative, is found not to conform to the limited warranty set forth above, or (b) the repair of such product or part, or
(c) the refund or crediting to Buyer of the net sales price of the defective product or part.

BUYER’S REMEDIES CONTAINED HEREIN ARE EXCLUSIVE OF ANY OTHER REMEDY OTHERWISE AVAILABLE TO BUYER.

Page 233 ends

Item # 9.

Warranty Begins:

Stainless steel piping shall be free from structural failures caused by defects in material and workmanship, or
perforation caused by corrosion.
(b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; (d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce.

Ten (10) Years
- or -
100,000 Miles
Warranty Period
Ends After:

Fire and Rescue Apparatus
Coverage:

Ten (10) Year Material and Workmanship
Stainless Steel Piping

The date of the original purchase invoice (issued when the product ships from the factory).

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

Pierce’s obligation under this warranty is limited to repairing or replacing without charge, as Pierce may elect, the
stainless steel piping or components which Pierce
determines to have failed due to defective material and workmanship, or perforation caused by corrosion.

This warranty does not cover the use of fluoroprotein (FP) type foam. The sodium chloride within FP foam can cause long-term damage to system components if not thoroughly flushed immediately after use.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE
POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

3. BUYER'S EXCLUSIVE REMEDY.

ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

2. DISCLAIMERS OF WARRANTIES
capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.

Page 234 ends

Item # 9.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE
POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

One (1) Year & Five (5) Year Warranty Period
Ends After:

ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

Fire and Rescue Apparatus
Coverage:

One (1) Year Material and Workmanship Foam System & Five (5) Year Material and Workmanship Control Head
Limited Warranty
Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

Limited warranty 1 year parts and labor for for the foam system and 5 years parts and labor for the control head.

1. LIMITED WARRANTY
(b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:

Page 235 ends

Item # 9.

Fire and Rescue Apparatus
Coverage:

Twenty (20) Year Structural Integrity
Pierce Aerial Device
Limited Warranty
Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

Each new Pierce Aerial Device shall be free from defects in material and workmanship.

Aerial Device Models Covered by this warranty include:

Aerial Platforms
Aerial Ladders
SkyBoom

1. LIMITED WARRANTY
(b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This warranty applies only to the torque box, turntable, aerial sections and other structural components of the aerial
device, as identified in the Pierce specifications for the aerial device. This warranty shall be void if, or to the extent that the aerial device is not maintained in strict compliance with NFPA Standard 1911 in effect at time of sale, including such periodic inspections and testing by qualified third parties as are required by that Standard as it may be in effect from time to time. Proof of such compliance shall accompany any
claims under this warranty. Third party testing agencies known to Pierce to be qualified for such purposes may be obtained from the Pierce Customer Service Department
This warranty does not apply to damage caused by
corrosion.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE
POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

Twenty (20) Years
- or -
100,000 Miles
Warranty Period
Ends After:

ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

Page 236 ends

Item # 9.
{00046826;v2}
AMITY FIRE AND SAFETY, INC.
3750 CHESTNUT ROAD
ALBURTIS, PA 18011-0451
Phone: 610-966-3115
Fax: 610-965-6313
* STANDARD FIVE YEAR WARRANTY *
(standard warranty is in effect for parts shipped after 4/15/10) Three Function Swivel
A. PRESHIPMENT TESTING The Three Function Swivel fabricated by Amity which is exposed to pressure during normal use is subject to final inspection using the following pressure minimums:

1. Hydrostatic applications will be tested to 400 PSI unless specified otherwise on approved drawings. Operating pressures on installed systems are not to exceed 250 PSI at any point in the system. Warranty will be voided and Amity will not be held liable for failure and/or damage occurring from Water Hammering or freezing of water in any system.

2. Hydraulic applications will be tested to 4000 PSI. System operating pressure in application to be 3000 PSI maximum.

3. Dielectric and Continuity Test all circuits. 30 Amp max current loading.

B. THREE FUNCTION SWIVEL MAINTENANCE – Our Three Function Swivel has been fully tested at assembly. Under no circumstances is there to be any maintenance performed internally or externally to the Three Function Swivel by Purchaser or any other third party other than an authorized representative of or Amity itself. The Three Function Swivel is sealed and must remain so. The Three Function Swivel is designed for a long maintenance free life. Should any problems occur or replacement be necessary, first contact Amity. There is to be no field maintenance performed on the Three Function Swivel .

C. MOUNTING REQUIREMENTS – The following are the mounting requirements for the Three Function Swivel:

1. Mounting points and methods are to be determined at the initial design stage. All drawings and applicable documentation must be signed off by both parties and filed for future reference. No deviation to the approved mounting is allowed without approval from Amity.

2. The Three Function Swivel is to be mounted concentric to the center of the turntable bearing.

3. All inlet and outlet plumbing to conform to swivel mounting, under no circumstances is the Three Function Swivel to be positioned to match connections. This will avoid putting excessive loads on the Three Function Swivel. All tubing or piping to be supported by means other than the Three Function Swivel.

D. LIMITED WARRANTY, LIMITATIONS, CONDITIONS AND PROCEDURES REQUIRED.

1. The Three Function Swivel is warranted to be free of defects in labor and/or materials for a period of five (5) years from the Date of Service. For purposes here, “Date of Service” shall mean the date when the Three Function Swivel, or the unit to which the Three Function Swivel is incorporated, passes final Underwriters Laboratory testing, or similarly compliant testing, and is certified for service. Evidence of such Date of Service shall be required in connection with any warranty claim by Purchaser.

2. The Three Function Swivel shall be repaired or replaced at the sole option and expense of the Amity provided the Three Function Swivel alleged to be defective was used for its intended normal use of operation and subject to the following qualifications and limitations.

3. Any alteration of the Three Function Swivel without consent from Amity is strictly forbidden and shall void warranty.

4. No welding shall be performed on finished Three Function Swivel.

5. No responsibility is assumed for any malfunctions or damages which are occasionally caused by foreign objects which may be ingested into water or hydraulic systems such as, but not limited to stones, sand or metal chips.

6. Amity assumes responsibility for our Three Function Swivel, which is defective only, and therefore, it will not assume responsibility for labor to either remove or install our Three Function Swivel unless it agrees in writing to assume such responsibility.

7. Unless otherwise approved in writing by the Amity all returns of defective Three Function Swivels (or allegedly defective Three Function Swivels) are at Purchaser’s expense and must include a RGA number issued by the Amity.

Page 237 ends

Item # 9.
{00046826;v2}

8. All warranty claims must be presented at the time the problem occurs, or as soon as practical thereafter, either called or faxed to the Amity and include the numbers on the assembly’s Amity’s label with a detailed explanation of the difficulty in order for the matter to be appropriately evaluated and resolved.

9. Amity will not be held liable for damage incurred during shipment.

10. No responsibility shall be assumed for misuse or improper mounting, unreasonably use or abuse of the Three Function Swivel and or failure to provide or use improper maintenance, failure to follow written installation and use in instruction or any use other than the customary designed use.

THE REMEDIES PROVIDED IN THE ABOVE EXPRESS LIMITED WARRANTY AND ARE THE SOLE AND EXCLUSIVE REMEDIES AVAILABLE. NO OTHER EXPRESS WARRANTIES ARE MADE. ALL IMPLIED

WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR USE ARE LIMITED IN DURATION AS SET FORTH ABOVE. IN NO EVENT SHALL THE AMITY ASSUME OR BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES.

THE WITHIN DESCRIBED WARRANTY SHALL ONLY BE AFFORDED TO THE ORIGINAL PURCHASER OR FOR

INCORPORATION INTO ANOTHER UNIT AND TO FIRST PURCHASER AS PART OF COMPLETED UNIT,

HOWEVER, THE WARRANTY PERIOD OF FIVE YEARS IS FROM THE DATE OF SERVICE WITH THE UNDERSTANDING IT IS INSTALLED WITHIN A REASONABLE TIME PERIOD.

Dated: _______________ ____, 20__

Page 238 ends

Item # 9.

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES

ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

Pierce's obligation under this warranty is limited to repairing or replacing without charge, as Pierce may elect, the
hydraulic lines, fittings, valves, seals, cylinders, filters, pumps, hydraulic motors, rotary actuators, or components which Pierce determines to have failed due to defective material and workmanship.

This warranty shall not apply unless the aerial device is inspected in accordance with NFPA 1911 Standard for
Inspection, Maintenance, Testing, and Retirement of InService Automotive Fire Apparatus and the applicable Pierce Operator and Maintenance Manuals.

Conditions and
Exclusions:

Fire and Rescue Apparatus
Coverage:

Five (5) Year Material and Workmanship Aerial Hydraulic System Components
Three (3) Year Material and Workmanship Aerial Hydraulic System Seals
Five (5) Years and Three (3) Years Warranty Period
Ends After:

The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:

The aerial hydraulic system components and seals shall be free from component or structural failures caused by defects in material and/or workmanship.
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE
POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

3. BUYER'S EXCLUSIVE REMEDY.

Page 239 ends

Item # 9.
{00046826;v2}
AMITY FIRE AND SAFETY, INC.
3750 CHESTNUT ROAD
ALBURTIS, PA 18011-0451
Phone: 610-966-3115
Fax: 610-965-6313
* STANDARD TEN YEAR WARRANTY *
(standard warranty is in effect for parts shipped after 4/15/10) Telescopic Waterways
A. PRESHIPMENT TESTING All waterways fabricated by Amity are final inspected using the following pressure minimums:

B. COMPONENTS DESCRIPTION AND MAINTENANCE

1. All components are thoroughly greased at assembly. Since internally lubricated seals are used, regular greasing is not required. We recommend components not be greased at installation.

2. Slip Tube Assemblies may be greased at the Amity’s regularly scheduled Aerial Inspections. The seals in the Slip Tube Assemblies are self-lubricating, so greasing is not mandatory. We do recommend a visual inspection of the Slip Tube Assembly while it is fully extended after initial installation, from that point on we recommend inspection every ten hours of aerial operation. If any deposits of aluminum appear, they are to be rubbed off using a Teflon scouring pad.

Slip Tube Assemblies are designed to give long maintenance free service; however, like any product, problems may occur and periodic visual inspections will aid in determining if a potential problem exists and warrants a call to us.

Care must be taken to keep debris off of extended tubes. We recommend wiping tubes with light oil (10 weight) or hydraulic oil after use, if tubes appear to have contamination on them. Under no circumstance are tubes to be cleaned with lacquer thinner, or any other solvent.

C. LIMITED WARRANTY, LIMITATIONS, CONDITIONS AND PROCEDURES REQUIRED.

1. Products are warranted to be free of defects in labor and/or materials for a period of ten years from the date of purchase from the Amity and shall be repaired or replaced at the sole option and expense of the Amity provided the products alleged to be defective was used for its intended normal use operation and subject to the following qualifications and limitations.

2. Any alteration of product without consent from Amity is strictly forbidden and shall void warranty.

3. No welding shall be performed on finished product.

4. No responsibility is assumed for any malfunctions or damages which are occasionally caused by foreign objects which may be ingested into water system such as, but not limited to stones, sand or metal chips.

5. Amity assumes responsibility for our product, which is defective only, and therefore, it will not assume responsibility for labor to either remove or install our product unless it agrees in writing to assume such responsibility.

6. Unless otherwise approved in writing by the Amity all returns of defective (or allegedly defective products) are at Purchaser’s expense and must include a RGA number issued by the Amity.

7. All warranty claims must be presented at the time the problem occurs, or as soon as practical thereafter, either called or faxed to the Amity and include the numbers on the assembly’s Amity’s label with a detailed explanation of the difficulty in order for the matter to be appropriately evaluated and resolved.

8. Amity will not be held liable for damage incurred during shipment.

9. No responsibility shall be assumed for misuse or improper mounting, unreasonably use or abuse of the Product and or failure to provide or use improper maintenance, failure to follow written installation and use in instruction or any use other than the customary designed use.

THE REMEDIES PROVIDED IN THE ABOVE EXPRESS LIMITED WARRANTY AND ARE THE SOLE AND EXCLUSIVE REMEDIES AVAILABLE. NO OTHER EXPRESS WARRANTIES ARE MADE. ALL IMPLIED

WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR

Page 240 ends

Item # 9.
{00046826;v2}
FITNESS FOR A PARTICULAR PURPOSE OR USE ARE LIMITED IN DURATION AS SET FORTH ABOVE. IN NO EVENT SHALL THE AMITY ASSUME OR BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES.

THE WITHIN DESCRIBED WARRANTY SHALL ONLY BE AFFORDED TO THE ORIGINAL PURCHASER OR FOR

INCORPORATION INTO ANOTHER UNIT AND TO FIRST PURCHASER AS PART OF COMPLETED UNIT,

HOWEVER, THE WARRANTY PERIOD OF TEN YEARS COMMENCES UPON INSTALLATION INTO FINAL ASSEMBLY WITH THE UNDERSTANDING IT IS INSTALLED WITHIN SIX MONTHS OF PURCHASE.

Dated: ____________________ ____, 20___

Page 241 ends

Item # 9.

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This limited warranty is applicable to the vehicle in the following percentage costs of warranty repair, if any:

Topcoat Durability & Appearance: Gloss, Color Retention & Cracking
0-24 months 100%
25-48 months 50%
Integrity of Coating System: Adhesion, Blistering/Bubbling 0-24 months 100%
25-48 months 50%
Corrosion: Dissimilar Metal and Crevice
0-24 months 100%
25-48 months 50%
Corrosion Perforation
0-24 months 100%
25-48 months 50%
This limited warranty applies only to exterior paint.

Conditions and
Exclusions:

Fire and Rescue Apparatus
Coverage:

Four (4) Year Pro-Rated Paint and Corrosion
Aerial Device
Four (4) Years Warranty Period
Ends After:

The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:

Aerial device shall be free from blistering, peeling, corrosion or any other adhesion defect caused by defective
manufacturing methods or paint material selection for
exterior surfaces.
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

3. BUYER'S EXCLUSIVE REMEDY.

Page 242 ends

Item # 9.

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This limited warranty is applicable to the vehicle in the following percentage costs of warranty repair, if any:

Conditions and
Exclusions:

Fire and Rescue Apparatus
Coverage:

Ten (10) Year Pro-Rated Paint and Corrosion
Custom Body
Ten (10) Years Warranty Period
Ends After:

The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:

Exterior surfaces of the body shall be free from blistering, peeling, corrosion or any other adhesion defect caused by defective manufacturing methods or paint material selection. (d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

3. BUYER'S EXCLUSIVE REMEDY.

Page 243 ends

Item # 9.

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This warranty does not cover damage from lack of
maintenance and cleaning (proper cleaning and maintenance procedures are detailed in the Pierce operation and
maintenance manual).

Conditions and
Exclusions:

Fire and Rescue Apparatus
Coverage:

One (1) Year Material and Workmanship
Graphics Fading and Deterioration
One (1) Year Warranty Period
Ends After:

The date the apparatus is placed in service, or 60 days from the original buyer invoice date, whichever comes first. Warranty Begins:

Each graphic lamination shall be free from defects in material, workmanship, fading, and deterioration.
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

3. BUYER'S EXCLUSIVE REMEDY.

Page 244 ends

Item # 9.

JROGHQVWDWHĆUHFRP

DEALER SUPPLIED

PRODUCTS SERVICES
Exhibit “D”
5 AND
/OR

Page 245 ends

Item # 9.
1 PROPOSAL INTRDUCTION
With over three decades of industry expertise, Golden State Fire Apparatus, Inc. (GSFA) proudly stands as the premier authorized dealership for top-tier fire apparatus in Central and Northern California. Our steadfast commitment to detail and customer satisfaction has earned us a trusted reputation among first responders.

We sincerely appreciate the opportunity to present this comprehensive proposal for a PIERCE MANUFACTURING, INC. 107’ ENFORCER ASCENDANT QUINT AERIAL. Your consideration of this proposal is greatly valued, and we are eager for the opportunity to support your department with the highest level of excellence and professionalism.

DEALER-SUPPLIED PRODUCTS AND SERVICES
Golden State Fire Apparatus Inc. (GSFA) will furnish the following items and/or services before final delivery so that all necessary components and support are in place, contributing to an efficient final delivery process. Please refer to the detailed list below for a comprehensive overview of the products and/or services included:

AUTHORIZED MANUFACTURER
In accordance with the State of California Vehicle Code, specifically Section 11701, it is mandated that "every manufacturer of a vehicle subject to registration shall make application to the Department of Motor Vehicles (DMV) for a license containing a general distinguishing number." The manufacturer, as of the proposal submission, holds a valid license in compliance with this requirement and is prepared to furnish a copy upon request. This adherence to regulatory standards ensures that the manufacturer maintains a current and official status, promoting transparency and compliance with legal requirements throughout the duration of the proposal and subsequent processes.

AUTHORIZED DEALERSHIP
In compliance with the State of California Vehicle Code, specifically Section 11701, it is mandated that "a dealer in vehicles of a type subject to registration shall make application to the Department of Motor Vehicles (DMV) for a license containing a general distinguishing number." Golden State Fire Apparatus, Inc. possesses a valid license at the time of the bid, as detailed above, and can promptly provide a copy upon request. This adherence to regulatory standards ensures that the dealership maintains a current and official status, promoting transparency and compliance with legal requirements throughout the duration of the proposal and subsequent processes.

AUTHORIZED SALES REPRESENTATIVE
In accordance with the State of California Vehicle Code, specifically Section 11800, it is expressly prohibited for any individual to function as a vehicle salesperson without obtaining a license issued by the Department of Motor Vehicles (DMV). The representative, at the time of

Page 246 ends

Item # 9.
2 proposal, holds a valid vehicle salesperson's license and is ready to furnish a copy upon request.

This adherence to regulatory standards ensures that the sales representative maintains a current and official status, promoting transparency and compliance with legal requirements throughout the bidding process and subsequent phases.

VEHICLE REGISTRATION
In adherence to the State of California Vehicle Code Section 11739, it is mandated that the "dealer of a new motor vehicle sale is responsible for applying for the title, securing vehicle registration, and obtaining license plates for the Customer" through the Department of Motor Vehicles (DMV). Being a factory-authorized dealer of the vehicle being sold, Golden State Fire Apparatus, Inc. is duly authorized to register the vehicle with the State of California as a new vehicle manufacturer.

GSFA is committed to facilitating an excellent vehicle ownership experience for the customer.

As such, we will manage all necessary applications and complete all transfer papers, including the application for California Exempt "E" license plates. This approach ensures compliance with regulatory requirements and a hassle-free registration process for our valued customers.

WEEKLY PROGRESS PHOTOGRAPHS
GSFA is committed to ensuring transparency and comprehensive reporting throughout the construction process of the apparatus. To achieve this, GSFA will provide weekly photographs capturing various stages of the apparatus or major components under construction.

Commencing from the initiation of the manufacturing process, the photographic documentation will extend throughout the entire production phase by the manufacturer. These weekly reports will offer a visual representation of the ongoing progress of the apparatus, highlighting key milestones and showcasing unique features and aspects as construction unfolds.

Our focus is to provide customers with a clear and detailed insight into the evolution of the apparatus, fostering a deeper understanding of the craftsmanship and distinct elements incorporated during the construction process. This commitment to regular, visual updates aims to enhance communication and transparency regarding the progress of the apparatus.

PRE-CONSTRUCTION, FACTORY VISIT
A pre-construction trip to the manufacturing facility is included for three (3) Customer representatives. The primary objective of this visit is to review and finalize, in detail, the specifications prior to the start of production. The pre-construction trip is anticipated to span four (4) days and three (3) nights, with scheduling details collaboratively determined between GSFA and the Customer.

Page 247 ends

Item # 9.
3 GSFA will cover the costs associated with airfare, lodging, meals, and ground transportation during the stay at the manufacturer's location. Air travel will be arranged from one of the following airports: Sacramento, San Francisco, or San Jose.

It is important to note that certain costs, including Customer ground transportation within California, airport parking, luggage fees, and incidental expenses during travel to the factory, fall within the responsibility of the Customer. Furthermore, flight reservations are nonrefundable, and in the event of a cancellation post-booking, the Customer will bear all associated costs, encompassing not only the original ticket cost but also any change or cancellation fees levied by the airline and/or travel agency. Additionally, flight reservations are non-transferable. This delineation aims to establish clarity and transparency regarding the allocation of responsibilities and potential costs associated with the pre-construction trip.

FINAL INSPECTION, FACTORY VISIT
A final inspection trip to the manufacturing facility is included for three (3) Customer representatives. The primary objective of this visit is to ensure the adherence of the apparatus to specifications and promptly identify any potential deficiencies. The final inspection trip is anticipated to span four (4) days and three (3) nights, with scheduling details collaboratively determined between GSFA and the Customer.

GSFA will cover the costs associated with airfare, lodging, meals, and ground transportation during the stay at the manufacturer's location. Air travel will be arranged from one of the following airports: Sacramento, San Francisco, or San Jose.

DELIVERY TO AUTHORIZED SERVICE FACILITY
GSFA will deliver the apparatus to one our Northern California facilities (either Tracy or Sacramento – whichever is closest) for a comprehensive dealer preparation inspection. This service, conducted at the expense of GSFA, aims to have the apparatus in optimal condition at the time of final delivery.

To ensure the proper break-in of all components while still under warranty, the apparatus will be delivered under its own power. The use of rail or truck freight for transportation is deemed

Page 248 ends

Item # 9.
4 unacceptable in order to uphold the highest standards of quality assurance during the delivery process. This approach reflects our commitment to delivering a fully operational, road-tested apparatus to our valued customers.

PRE-DELIVERY SERVICE
Before reaching its final destination, the apparatus undergoes a pre-delivery service conducted by Golden State Emergency Vehicle Service, Inc. This service is designed to tap into the expertise of an external source, providing an experienced perspective that enhances the thoroughness of your final inspection. Our pre-delivery service covers the following areas:

1. Engine Compartment and Undercarriage:
• Inspect for broken mounting brackets.
• Inspect and identify locations of any fluid leaks.
• General inspection of hoses, wiring, and linkage, focusing on potential wear points. • Verify correct fluid capacities for engine oil, coolant, power steering fluid, washer reservoir fluid, transmission fluid, rear-end fluid, pump transmission oil, and primer oil if applicable.
• Re-torque U-bolts to OEM specifications if equipped with leaf spring suspension (Pierce Custom chassis only).

2. Interior:
• Confirm proper operation of doors, windows, and locks, ensuring accurate adjustment.
• Confirm proper operation of seatbelt alarms.
• Confirm proper operation of all compartment door alarms, as well as hose bed cover, ladder rack, light tower, and deck gun alarms.
• Ensure functionality of auxiliary power points, interior lighting, mirror, and seat controls, and if applicable - headsets and radios.
• Inspect upholstery for quality and condition.

3. Exterior:
• Address reasonable paint scratches or chips.
• Tighten any loose hardware.
• Inspect tires and wheels, ensure proper pressure.
• Check compartment doors for proper operation and latch fit. • Lubricate compartment door locks if applicable.

4. Road Test:
• Conduct a road test with a full water tank (if applicable), covering approximately twenty miles on both city and highway roads.

Page 249 ends

Item # 9.
5 • Perform a DOT compliant brake test to verify the system is holding air. • Inspect brake condition, wheel seals, and ensure drive train components reach optimal operating temperatures.
• Conduct an Allison Transmission self-diagnostic to verify fluid level, fluid and filter life, and check for fault codes.

5. Electrical:
• Verify the operation of all lights, sirens, and other electrical accessories.

6. Pump:
• Operate the Pressure Governor or Relief Valve, transfer valve, and check pump shift. • Inspect water tank, pump and plumbing for leaks and calibrate the water level gauge.
• Ensure smooth operation of all discharge, suction, and drain valves.

7. Pierce Husky™ Foam System:
• If applicable, draft and inject clean water to ensure proper operation of the foam pump.

8. Fuel and DEF Tanks:
• Fill the fuel tank and DEF tank prior to final delivery.

9. Wash:
• Thoroughly wash the apparatus prior to final delivery.

This pre-delivery service assists the apparatus to meet our high standards of quality and operational efficiency before reaching its final destination.

FINAL DELIVERY (CUSTOMER LOCATION)
GSFA will deliver the completed Product, inclusive of any relevant equipment, spare parts, and supplies, to the Customer's specified address at GSFA's expense.

In preparation for the Product's delivery, the Customer is required to furnish GSFA with proof of liability and physical damage insurance. GSFA will withhold the release of the Product until such proof of insurance is provided.

To ensure a timely delivery process, it is incumbent upon the Customer to settle any outstanding balance owed to GSFA before or at the time the Product is completed and ready for delivery. In the event of delayed payment or delivery, GSFA reserves the right to impose a

Page 250 ends

Item # 9.
6 late fee and daily storage charge as outlined in the Standard Terms and Conditions until payment is received.

For compliance with insurance liability considerations, the Product will only be delivered upon full acceptance and full payment, or through a prior written agreement mutually reached between the Customer and GSFA. This ensures a secure and efficient finalization of the delivery process, aligning with both parties' obligations and safeguarding against potential liabilities.

COMPREHENSIVE SALES AND SERVICE SUPPORT
At GSFA, we understand that immediate response is essential - and the service and support of your apparatus should be no different. Since our founding in 1989, our mission has been to provide first responders with the highest quality, most reliable fire and emergency apparatus from top-tier manufacturers. We specialize in guiding our customers through the entire process - from apparatus evaluation and customization to final inspection - and ensuring years of reliable service through our Golden State Emergency Vehicle Service (GSEVS) division.

Golden State Emergency Vehicle Service (GSEVS)
Established in 2014, GSEVS is committed to building long-term, collaborative relationships by providing exceptional warranty and technical support. Our services cover a wide range of needs, including chassis, electrical systems, pump, aerial, routine maintenance, equipment mounting, and pump testing - with priority given to new units sold by GSFA. Our goal is to deliver prompt, professional service and unwavering support for your apparatus.

Sacramento Facility
Our Sacramento location features a 33,814-square-foot facility with 18 working bays and a 4,500-square-foot, two-story parts distribution department stocked with an extensive inventory of Pierce and non-Pierce parts. Conveniently located near Highway 99 with easy access to Interstates 80 and 50, we are positioned to serve you efficiently. If a part is not in stock, we order it directly from the factory to minimize downtime.

Tracy Facility (Opening Fall 2025)
Our second location in Tracy will expand our service capacity with a 49,634-square-foot facility featuring 22 working bays and a parts department equal in size to our Sacramento facility.

Strategically located within the "Tracy Triangle" - bordered by I-580, I-205, and I-5 - this facility will enhance our ability to serve customers in the Bay Area and beyond.

Mobile Service
To minimize emergency apparatus downtime, we offer a robust mobile service program for onsite repairs and maintenance.

Certified and Experienced Technicians

Page 251 ends

Item # 9.
7 Our service team includes factory-trained professionals certified by Pierce, ASE, and EVT. They undergo regular training to stay current on chassis, electrical systems, and aerial devices, ensuring expert handling of any challenge.

Your Single Source for Sales and Service
With Golden State Fire, you have a single point of contact for sales, service, and support - all under one roof, with two strategically located facilities to serve you better. We are confident that our combination of expertise, customer service, and product support is unmatched by any other fire and emergency apparatus dealership in California.

END OF EXHIBIT “D”

Page 252 ends

Item # 9.

City of Grass Valley
City Council
Agenda Action Sheet
Title: Appointment of Planning Commissioner
CEQA: Not a Project
Recommendation: That Council approve the appointment of Matthew Wich as Planning Commissioner for Councilmember Ivy.

Prepared by: Taylor Whittingslow, Deputy City Manager
Council Meeting Date: 4/8/2025 Date Prepared: 4/3/2025
Agenda: Consent
Background Information: By Council policy, each council member submits a candidate for appointment to the Planning Commission to the members of the City Council for their approval and appointment. The terms of appointed Planning Commissioners coincide with the nominating Council Member’s term of office and may be changed by that city council member at any time during their term in office. Councilmember Ivy has chosen Matthew Wi h to fill the position of his Planning Commissioner.

Council Goals/Objectives: This item executes portions of work tasks towards High Performance Government and Quality Service Goal # 5.A.3: Continue to build cooperative relationships with representatives from service clubs and other community groups.

Fiscal Impact: N/A
Funds Available: N/A Account #: N/A
Reviewed by: __ City Manager
Attachments: None

Page 253 ends

Item # 10.

City of Grass Valley
City Council
Agenda Action Sheet
Title: Loma Rica Open Space Fuel Reduction Project
CEQA: Exempt under CEQA Guideline §15304, Categorical Exemption Class 4 (“Minor Alterations to Land”)
Recommendation: That Council authorize the advertisement for bids for the Loma Rica Open Space Fuels Reduction Project.

Prepared by: Tim Kiser, City Manager
Council Meeting Date: 04/08/2025 Date Prepared: 04/04/2025 Agenda: Consent
Background Information: At its meeting on November 12, 2024, the City Council authorized staff to accept the dedication of open space land across the Loma Rica Ranch property. This land dedication is intended to enhance the City’s ability to protect and manage the natural, scenic, historical, and conservation values of the area, while also supporting future trail development and land improvement projects.

The newly acquired City-owned open space encompasses approximately 200 acres of heavily forested land with dense underbrush. To mitigate wildfire risk and improve overall forest health, a hazardous fuel reduction project is proposed. The project will involve the selective removal of surface fuels, brush and shrubs, live trees under 10 inches in diameter at breast height, and other ladder fuels that contribute to the ignition and spread of wildfire. Vegetation removal will be achieved through a combination of mechanical mastication, hand crew cutting, chipping, and mulching.

The primary goals of the project are to:
 Disrupt vertical and horizontal fuel continuity;
 Reduce the intensity and spread of potential wildfires;  Enhance ingress and egress for emergency response; and  Restore a healthy, park-like forest condition that is more fire-resilient.

Vegetation in the treatment area is best described as a mixed conifer forest with a manzanita understory. Residual trees will be pruned to a height of approximately 8 to 10 feet. Dead trees of any size may be felled and chipped, masticated, or mulched. The resulting material may be scattered on site in a manner consistent with habitat preservation, burned using an air curtain burner (with appropriate permits), or removed for offsite processing.

Environmental protection measures will be strictly observed. All activities will avoid watershed areas within 50 feet of Whitewater Creek, Wolf Creek, their tributaries, or any

Page 254 ends

Item # 11.
blue line waterways, including irrigation ditches, as identified on current USGS 7.5-minute topographic maps. Areas located within FEMA-designated flood zones will be treated using hand tools only. Known archaeological or cultural resources will be avoided, and if any such resources are discovered during operations, work in the area will cease until a qualified cultural resource specialist provides further guidance.

The Loma Rica Open Space Fuel Reduction Project qualifies for a Categorical Exemption under the California Environmental Quality Act (CEQA) pursuant to CEQA Guidelines Section 15304, Class 4 (“Minor Alterations to Land”).

The total project cost is estimated at $400,000. Bid documents are available for public review at City Hall. Staff anticipates awarding a contract in Spring 2025, with fuel reduction work to commence shortly thereafter.

Staff recommends that the City Council authorize the public bidding process for this project.

Council Goals/Objectives: The Loma Rica Hazardous Fuels Reduction Project works towards achieving/maintaining the 2022 Strategic Plan Update: Community Safety and City Infrastructure Investment.

Fiscal Impact: Measure B Funds are anticipated to be used to hire a contractor to prepare a hazardous fuel treatment prescription and carry out treatment of the City-owned Loma Rica Open Space parcels. This will be subject to Measure B oversight committee and City Council approval prior to the award of this project.

Funds Available: Yes Account #: 207-102-51110
Reviewed by: ____ City Manager Attachments: Project Area Maps

Page 255 ends

Item # 11.

Location Project Maps

Page 256 ends

Item # 11.

City of Grass Valley
City Council
Agenda Action Sheet
Title: Appointment of Measure E Oversight Committee Members CEQA: Not a Project
Recommendation: That the City Council appoint Measure E Oversight Committee member Branstrom to a term ending December 2028.

Prepared by: Taylor Whittingslow, Deputy City Manager
Council Meeting Date: 4/8/2025 Date Prepared: 4/7/2025
Agenda: Consent
Background Information: In 2018, Grass Valley citizens voted to approve Measure E, a voter initiative tax measure that repealed the previous 1/2 percent City transaction and use (sales) tax and replaced it with an ongoing 1 percent sales tax. Measure E expands funding for such general fund purposes as increased police and fire services, enhancing parks and recreational services, and improving streets and sidewalks. All Measure E funds stay local, and all expenditures are subject to an annual audit by an independent citizen oversight committee.

The Citizen’s Oversight Committee reviews an independent audit of tax receipts and how they are spent each year and advises the City Council on how tax money should be spent. The Council must discuss the audit results at a public meeting each year and post them on the City’s website.

The most recently elected city councilmembers were tasked with nominating one new Measure E Oversight Committee member:
 Councilmember Arbuckle has nominated Grass Valley community member Bob Branstrom.

Council Goals/Objectives: The Measure E Oversight Committee executes portions of work tasks towards achieving/maintaining Strategic Plan – Open and Collaborative City Government.

Fiscal Impact: N/A Funds Available: N/A Account #: N/A
Reviewed by: __ City Manager

Page 257 ends

Item # 12.

City of Grass Valley
City Council
Agenda Action Sheet
Title: Approve Resolution 2025-09 Renaming the road through Memorial Park to Lou Conter Way
CEQA: Not a project
Recommendation: That the City Council approve Resolution 2025-09 naming of a street within Memorial Park in Grass Valley, CA, in honor of Lou Conter, in recognition of his distinguished military service and contributions to the nation and community.

Prepared by: Tim Kiser, City Manager
Council Meeting Date: 04/08/2025 Date Prepared: 04/03/2025 Agenda: Administrative
Background Information: Lou Conter (1921–2024) was a highly decorated U.S. Navy veteran and a longtime Grass Valley resident. At the time of his passing, he was the last surviving crew member of the USS Arizona, which was tragically lost during the attack on Pearl Harbor in 1941. On that fateful day, he courageously aided wounded shipmates and helped evacuate those who were blinded, burned, or injured. In the aftermath of the attack, he assisted with recovery efforts and continued serving his country with distinction.

Following Pearl Harbor, Conter’s military career spanned World War II and the Korean War. He was awarded the Distinguished Flying Cross for his heroic role in rescuing 219 Australians in New Guinea. He later served as an intelligence officer and advisor to Presidents Eisenhower, Kennedy, and Johnson, and played a pivotal role in the development of the Navy’s Survival, Evasion, Resistance, and Escape (SERE) training program. Among his many honors, he received the Navy Commendation Medal and was the first recipient of the USS Arizona Medal of Freedom.

Naming a street in Memorial Park after Lou Conter is a fitting tribute to his extraordinary service and heroism, ensuring that his sacrifices and contributions are remembered for generations to come. Memorial Par
Honoring Lou Conter by naming a street in Memorial Park aligns with the City of Grass Valley’s commitment to recognizing distinguished community members and military heroes. Staff recommends that the City Council approve this initiative.

Page 258 ends

Item # 13.

Council Goals/Objectives: The execution of this action attempts to achieve the following Strategic Goals – Community and Sense of Place.

Fiscal Impact: The cost of signage and minor administrative updates is expected to be minimal and will be covered under the city's existing budget for park maintenance and improvements.

Funds Available: Yes Account #: 100-503-51020
Reviewed by: City Manager
Attachments:
 Resolution 2025-09 Approving the Naming of the Street through Memorial Park from Oak Street to Race Street as "Lou Conter Way"
 Exhibit A – Location Map

Page 259 ends

Item # 13.

Exhibit A - Location Map
Proposed Lou Conter Way in Memorial Park (Green Highlighted Section)

Page 260 ends

Item # 13.

RESOLUTION 2025-09

A RESOLUTION OF THE CITY COUNCIL OF THE CITY OF GRASS VALLEY APPROVING

THE NAMING OF THE STREET THROUGH MEMORIAL PARK FROM OAK STREET TO RACE STREET AS "LOU CONTER WAY"
WHEREAS, the City of Grass Valley is committed to recognizing distinguished community members and military heroes who have made significant contributions to the nation and local community; and
WHEREAS, Lou Conter (1921–2024) was a highly decorated U.S. Navy veteran and a longtime Grass Valley resident, whose heroic actions and military service exemplify courage, dedication, and sacrifice; and
WHEREAS, Lou Conter was the last surviving crew member of the USS Arizona, which was tragically lost during the attack on Pearl Harbor on December 7, 1941, and on that day, he displayed exceptional bravery in aiding and evacuating wounded shipmates; and WHEREAS, following the attack on Pearl Harbor, Lou Conter continued his distinguished military career through service in World War II and the Korean War, earning the Distinguished Flying Cross for his heroic role in rescuing 219 Australians in New Guinea; and WHEREAS, Lou Conter further served as an intelligence officer and advisor to Presidents Eisenhower, Kennedy, and Johnson and played a pivotal role in developing the U.S. Navy’s Survival, Evasion, Resistance, and Escape (SERE) training program; and WHEREAS, among his many honors, Lou Conter received the Navy Commendation Medal and was the first recipient of the USS Arizona Medal of Freedom; and WHEREAS, after retiring as a Lieutenant Commander in 1967, Lou Conter dedicated his life to educating future generations through veterans’ ceremonies and student lectures, ensuring that the sacrifices of those who served would never be forgotten; and WHEREAS, naming a street in Memorial Park in his honor serves as a fitting and lasting tribute to his legacy, ensuring that his service, heroism, and dedication to the nation and the Grass Valley community are memorialized for future generations; and WHEREAS, the proposed street renaming has been reviewed and recommended by City staff, and the minor cost associated with signage and administrative updates will be covered under the existing city budget for park maintenance and improvements.

NOW THEREFORE BE IT RESOLVED
The City Council of the City of Grass Valley hereby approves the naming of the street through Memorial Park, from Oak Street to Race Street, as "Lou Conter Way" in honor of Lieutenant Commander Lou Conter’s distinguished service and contributions to the community and the nation.

Page 261 ends

Item # 13.

ADOPTED as a Resolution of the City Council of the City of Grass Valley at a regular meeting held on the 8
th day of April 2025 by the following vote:

AYES: Council Member
NOES: Council Member
ABSENT: Council Member
ABSTAINING: Council Member
_____________________________
Hilary Hodge, Chair
ATTEST:
__________________________
Taylor Whittingslow, City Clerk
APPROVED AS TO FORM:
__________________________
Michael Colantuono, City Attorney

Page 262 ends

Item # 13.

City of Grass Valley
City Council
Agenda Action Sheet
Title: Partnership between Grass Valley Police Animal Services and Wayward Journey CEQA: Not a project
Recommendation: That Council (1) receive a presentation by GVPD and Wayward Journey; and (2) direct the Chief of Police to sign an MOU, subject to legal review.

Prepared by: Brian Blakemore, Police Lieutenant
Council Meeting Date: 04/08/2025 Date Prepared: 04/01/2025 Agenda: Administrative
Background Information
In mid-2024, the Grass Valley Police Department was approached by Alexandra Maloney who was interested in starting a new non-profit organization (NPO) with a goal of working with the Grass Valley Animal Shelter. The intent of the NPO, in coordination with staff, is to care for shelter animals by coordinating in-home foster care, conducting socialization and behavioral training, hosting vaccine clinics, raising money for specialized medical care, and more. GVPD staff met with Maloney and incorporated representatives from California Intergovernmental Risk Authority (CIRA) to come up with the framework of a relationship. That framework has been transformed into an MOU between the City and Wayward Journey and has been reviewed by the City Attorney.

The formalized partnership between the City and Wayward Journey will enhance the services we provide to the community. Their work inside and outside of the shelter will undoubtedly lead to an increase in the successful adoption of shelter animals. Wayward Journey’s investment in socialization and training will also free up some City staff time which can be redirected into other meaningful endeavors.

Wayward Journey intends to raise money through community donations, offering these services as a benefit to the community’s animals and is not asking for financial support from the City.

Council Goals/Objectives: This action executes portions of Strategic Plan Core Goal of an efficient workplace and high-quality public safety services.

Page 263 ends

Item # 14.

Fiscal Impact: No direct financial impact. Net positive in staff-time savings and shorter animal shelter stays.

Funds Available: N/A Account #:

Reviewed by: City Manager

Page 264 ends

Item # 14.
1 MEMORANDUM OF UNDERSTANDING
(City of Grass Valley / Wayward Journey)

1. IDENTIFICATION
This MEMORANDUM OF UNDERSTANDING (“Agreement”) is entered into by and between the City of Grass Valley, a California municipal corporation (“City”), and Wayward Journey, a California non-profit public benefit corporation (“Consultant”). The City and Consultant are collectively referred to herein as the “Parties.”

2. RECITALS

2.1. City has determined that it requires the following professional services from a consultant: Animal shelter services.

2.2. Consultant represents that it is fully qualified to perform such professional services by virtue of its experience and the training, education and expertise of its principals and employees. Consultant further represents that it is willing to accept responsibility for performing such services in accordance with the terms and conditions set forth in this Agreement.

2.3. Consultant represents that it has no known relationships with third parties, City Council members, or employees of City which would (1) present a conflict of interest with the rendering of services under this Agreement under Government Code Section 1090, the Political Reform Act (Government Code Section 81000 et seq.), or other applicable law, (2) prevent Consultant from performing the terms of this Agreement, or (3) present a significant risk of the disclosure of confidential information.

NOW, THEREFORE, for and in consideration of the mutual covenants and conditions herein contained, City and Consultant agree as follows:

3. DEFINITIONS

3.1. “Scope of Services”: Such professional services as are set forth in Exhibit A, attached hereto and incorporated herein by this reference.

3.2. “Agreement Administrator”: The Agreement Administrator for this project is [Name and title]. The Agreement Administrator shall be the principal point of contact at the City for this project. All services under this Agreement shall be performed at the request of the Agreement Administrator. The Agreement Administrator will establish the timetable for completion of services and any interim milestones. City reserves the right to change this designation upon written notice to Consultant

3.3. “Approved Fee Schedule”: Consultant’s compensation rates are set forth in the fee schedule attached hereto as Exhibit B and incorporated herein by this reference. This

Page 265 ends

Item # 14.
2 fee schedule shall remain in effect for the duration of this Agreement unless modified in writing by mutual agreement of the parties.

3.4. “Maximum Amount”: The highest total compensation and costs payable to Consultant by City under this Agreement. The Maximum Amount under this Agreement is ____________________ Dollars ($_______________).

3.5. “Commencement Date”: [date].

3.6. “Termination Date”: [date]

4. CAMPAIGN CONTRIBUTIONS
This Agreement is subject to Government Code section 84308. Consultant shall disclose any contribution to an elected or appointed City official’s campaign or committee of more than $500 in 12 months preceding the Commencement Date or earlier date provided by the statute, by Consultant, its, her, or his agent, or another party affiliated with Consultant. Consultant shall provide a signed copy of the attached Campaign Contribution Disclosure Form to City before, or concurrently with, Consultant’s execution of this Agreement and no later than the Commencement Date.

5. TERM
The term of this Agreement shall commence at 12:00 a.m. on the Commencement Date and shall expire at 11:59 p.m. on the Termination Date unless extended by written agreement of the parties or terminated earlier under Section 17 (“Termination”) below. Consultant may request extensions of time to perform the services required hereunder. Such extensions shall be effective if authorized in advance by City in writing and incorporated in written amendments to this Agreement.

6. CONSULTANT’S AND CITY’S DUTIES

6.1. Consultant’s Duties

6.1.1. Consultant’s Services. Consultant shall perform the services identified in the Scope of Services. City shall have the right to request, in writing, changes in the Scope of Services. Any such changes mutually agreed upon by the parties, and any corresponding increase or decrease in compensation, shall be incorporated by written amendment to this Agreement.

6.1.2. Coordination with City. In performing services under this Agreement, Consultant shall coordinate all contact with City through its Agreement Administrator.

6.1.3. Budgetary Notification. Consultant shall notify the Agreement Administrator, in writing, when fees and expenses incurred under this Agreement have reached eighty percent (80%) of the Maximum Amount. Consultant shall concurrently

Page 266 ends

Item # 14.
3 inform the Agreement Administrator, in writing, of Consultant’s estimate of total expenditures required to complete its current assignments before proceeding, when the remaining work on such assignments would exceed the Maximum Amount.

6.1.4. Business License. Consultant shall obtain and maintain in force a City business license for the duration of this Agreement.

6.1.5. Professional Standards. Consultant shall perform all work to the standards of Consultant’s profession and in a manner reasonably satisfactory to City. Consultant shall keep itself fully informed of and in compliance with all local, state, and federal laws, rules, and regulations in any manner affecting the performance of this Agreement, including all Cal/OSHA requirements, the conflict-of-interest provisions of Government Code § 1090 and the Political Reform Act (Government Code § 81000 et seq.).

6.1.6. Avoid Conflicts. During the term of this Agreement, Consultant shall not perform any work for another person or entity for whom Consultant was not working at the Commencement Date if such work would present a conflict interfering with performance under this Agreement. However, City may consent in writing to Consultant’s performance of such work.

6.1.7. Appropriate Personnel. Consultant has, or will secure at its own expense, all personnel required to perform the services identified in the Scope of Services. All such services shall be performed by Consultant or under its supervision, and all personnel engaged in the work shall be qualified to perform such services. [Name of Project Manager] shall be Consultant’s project administrator and shall have direct responsibility for management of Consultant’s performance under this Agreement. No change shall be made in Consultant’s project administrator without City’s prior written consent.

6.1.8. Substitution of Personnel. Naming any persons in the proposal or Scope of Services constitutes a promise to the City that those persons will perform and coordinate their respective services under this Agreement. Should one or more of such personnel become unavailable, Consultant may substitute other personnel of at least equal competence upon written approval of City. If City and Consultant cannot agree as to the substitution of key personnel, City may terminate this Agreement for cause.

6.1.9. Permits and Approvals. Consultant shall obtain, at its sole cost and expense, all permits and regulatory approvals necessary for Consultant’s performance of this Agreement. This includes, but shall not be limited to, professional licenses, encroachment permits, and building and safety permits and inspections.

6.1.10. Notification of Organizational Changes. Consultant shall notify the Agreement Administrator, in writing, of any change in name, ownership or control of

Page 267 ends

Item # 14.
4 Consultant’s firm or of any subcontractor. Change of ownership or control of Consultant’s firm may require an amendment to this Agreement.

6.1.11. Records. Consultant shall maintain all ledgers, books of account, invoices, vouchers, canceled checks, and other records or documents evidencing or relating to charges for services or expenditures and disbursements charged to City under this Agreement for a minimum of three (3) years, or for any longer period required by law, from the date of final payment to Consultant under this Agreement. All such documents shall be made available for inspection, audit, and/or copying at any time during regular business hours, upon oral or written request of City. In addition, pursuant to Government Code § 8546.7, if the amount of public funds expended under this Agreement exceeds $10,000, all such documents and this Agreement shall be subject to the examination and audit of the State Auditor, at the request of City or as part of any audit of City, for a period of three (3) years after final payment under this Agreement.

6.2. City’s Duties

6.2.1. City’s Duties. City shall perform the services identified in the Scope of Services.

The Parties shall have the right to request, in writing, changes in the Scope of Services. Any such changes mutually agreed upon by the parties, and any corresponding increase or decrease in compensation, shall be incorporated by written amendment to this Agreement.

7. SUBCONTRACTING

7.1. General Prohibition. This Agreement covers professional services of a specific and unique nature. Except as otherwise provided herein, Consultant shall not assign or transfer its interest in this Agreement or subcontract any services to be performed other than by an amendment to this Agreement.

7.2. Consultant Responsible. Consultant shall be responsible to City for all services to be performed under this Agreement.

7.3. Identification in Fee Schedule. All subcontractors shall be specifically listed, and their billing rates identified in the Approved Fee Schedule, Exhibit B. Any changes must be approved by the Agreement Administrator in writing.

7.4. Compensation for Subcontractors. City shall pay Consultant for work performed by its subcontractors, if any, only at Consultant’s actual cost plus an approved mark-up as set forth in the Approved Fee Schedule, Exhibit B. Consultant shall be liable and accountable for all payments, compensation, and federal and state taxes to all subcontractors performing services under this Agreement. City shall not be liable for any payment, compensation, or federal and state taxes to or for any subcontractors.

Page 268 ends

Item # 14.
5 8. COMPENSATION

8.1. General. City agrees to compensate Consultant for the services provided under this Agreement, and Consultant agrees to accept payment in accordance with the Fee Schedule in full satisfaction for such services. Compensation shall not exceed the Maximum Amount. Consultant shall not be reimbursed for any expenses unless provided for in this Agreement or authorized in writing by the Agreement Administrator in advance.

8.2. Invoices. Consultant shall submit to City an invoice, on a monthly basis or as otherwise agreed to by the Agreement Administrator, for services performed pursuant to this Agreement. Each invoice shall identify the Maximum Amount, the services rendered during the billing period, the amount due for the invoice, and the total amount previously invoiced. All labor charges shall be itemized by employee name and classification or position with the firm, the corresponding hourly rate, the hours worked, a description of each labor charge, and the total amount due for labor charges.

8.3. Taxes. City shall not withhold applicable taxes or other payroll deductions from payments made to Consultant except as otherwise required by law. Consultant shall be solely responsible for calculating, withholding, and paying all taxes.

8.4. Disputes. The parties agree to meet and confer at mutually agreeable times to resolve any disputed amounts in an invoice submitted by Consultant.

8.5. Additional Work. Consultant shall not be reimbursed for any expenses incurred for work performed outside the Scope of Services unless prior written approval is given by the City through a fully executed written amendment to this Agreement. Consultant shall not undertake any such work without prior written approval of the Project Administrator.

8.6. City Satisfaction as Precondition to Payment. Notwithstanding any other terms of this Agreement, no payments shall be made to Consultant until City is satisfied that the services are satisfactory.

8.7. Right to Withhold Payments. If Consultant fails to provide a deposit or promptly satisfy an indemnity obligation described in Section 12, City shall have the right to withhold payments under this Agreement to offset that amount.

9. PREVAILING WAGES
Consultant is aware of the requirements of California Labor Code Section 1720, et seq., and 1770, et seq., as well as California Code of Regulations, Title 8, Section 16000, et seq., (“Prevailing Wage Laws”), which require the payment of prevailing wage rates and the performance of other requirements on certain “public works” and “maintenance” projects. This Agreement is subject to Prevailing Wage Laws, for all work performed under this Agreement for which the payment of prevailing wage is required by those laws. Consultant shall defend,

Page 269 ends

Item # 14.
6 indemnify, and hold the City, its elected officials, officers, employees, and agents free and harmless from any claim or liability arising out of any failure or alleged failure of Consultant to comply with the Prevailing Wage Laws.

10. OWNERSHIP OF WRITTEN PRODUCTS
All reports, documents or other written material, and all electronic files, including computeraided design files, developed by Consultant in the performance of this Agreement (such written material and electronic files are collectively known as “written products”) shall be and remain the property of City without restriction or limitation upon its use or dissemination by City except as provided by law. Consultant may take and retain copies of such written products as desired, but no such written products shall be the subject of a copyright application by Consultant.

11. RELATIONSHIP OF PARTIES

11.1. General. Consultant shall be a wholly independent contractor as to the City under this Agreement.

11.2. No Agent Authority. Consultant shall have no power to incur any debt, obligation, or liability on behalf of City or to otherwise act on behalf of City as an agent. Neither City nor any of its agents shall have control over the conduct of Consultant or any of Consultant’s employees, except as set forth in this Agreement. Consultant shall not represent in any manner that it is, or that any of its agents or employees are, employees of City.

11.3. Independent Contractor Status. Under no circumstances shall Consultant or its employees look to the City as an employer. Consultant shall not be entitled to any benefits. City makes no representation as to the effect of this independent contractor relationship on Consultant’s previously earned California Public Employees Retirement System (“CalPERS”) retirement benefits, if any, and Consultant specifically assumes the responsibility for making such a determination. Consultant shall be responsible for all reports and obligations including, but not limited to: social security taxes, income tax withholding, unemployment insurance, disability insurance, and workers’ compensation, and other applicable federal and state taxes.

11.4. Indemnification of CalPERS Determination. If Consultant or any employee, agent, or subcontractor of Consultant providing services under this Agreement claims or is determined by a court of competent jurisdiction or CalPERS to be eligible for enrollment in CalPERS as an employee of the City, Consultant shall indemnify, defend, and hold harmless City for the payment of any employee and/or employer contributions for CalPERS benefits on behalf of Consultant or its employees, agents, or subcontractors, as well as for the payment of any penalties and interest on such contributions, which would otherwise be the responsibility of City.

Page 270 ends

Item # 14.
7 12. INDEMNIFICATION

12.1. Definitions. For purposes of this Section, “Consultant” shall include Consultant, its officers, employees, servants, agents, or subcontractors, or anyone directly or indirectly employed by either Consultant or its subcontractors, in the performance of this Agreement. “City” shall include City, its officers, agents, employees and volunteers.

12.2. Consultant to Indemnify City. To the fullest extent permitted by law, Consultant shall indemnify, hold harmless, and defend City from and against all claims, losses, costs or expenses for any personal injury or property damage arising out of or in connection with Consultant’s alleged negligence, recklessness or willful misconduct or other wrongful acts, errors or omissions of Consultant or failure to comply with any provision in this Agreement.

12.3. Scope of Indemnity. Personal injury shall include injury or damage due to death or injury to any person, whether physical, emotional, consequential or otherwise. Property damage shall include injury to any personal or real property. Consultant shall not be required to indemnify City for such loss or damage as is caused by the sole active negligence or willful misconduct of the City.

12.4. Attorney Fees. Such costs and expenses shall include reasonable attorney’ fees for counsel of City’s choice, expert fees, and all other costs and fees of litigation.

Consultant shall not be entitled to any refund of attorney’ fees, defense costs, or expenses if it is adjudicated to have been non-negligent.

12.5. Defense Deposit. The City may request a deposit for defense costs from Consultant with respect to a claim. If the City requests a defense deposit, Consultant shall provide it within 15 days of the request.

12.6. Waiver of Statutory Immunity. The obligations of Consultant under this Section are not limited by the provisions of any workers’ compensation act or similar act.

Consultant expressly waives its statutory immunity under such statutes or laws as to City.

12.7. Indemnification by Subcontractors. Consultant agrees to obtain executed indemnity agreements with provisions identical to those set forth here in this Section from every subcontractor or any other person or entity involved in the performance of this Agreement on Consultant’s behalf.

12.8. Insurance Not a Substitute. City does not waive any indemnity rights by accepting any insurance policy or certificate required pursuant to this Agreement. Consultant’s indemnification obligations apply whether or not any insurance policies are determined to be applicable to the claim, demand, damage, liability, loss, cost or expense.

Page 271 ends

Item # 14.
8 13. INSURANCE

13.1. Insurance Required. Consultant shall maintain insurance as described in this Section and shall require all its subcontractors, consultants, and other agents to do the same.

Approval of the insurance by the City shall not relieve or decrease any liability of Consultant. Any requirement for insurance to be maintained after completion of the work shall survive this Agreement.

13.2. Documentation of Insurance. City will not execute this Agreement until it has received a complete set of all required documentation of insurance coverage. However, failure to obtain the required documents prior to the work beginning shall not waive the Consultant’s obligation to provide them. Consultant shall file with City:
 Certificate of Insurance, indicating companies acceptable to City, with a Best’s Rating of no less than A:VII showing. The Certificate of Insurance must include the following reference: Animal shelter services.
 Documentation of Best’s rating acceptable to the City.  Original endorsements effecting coverage for all policies required by this Agreement.
 Complete, certified copies of all required insurance policies, including endorsements affecting the coverage.

13.3. Coverage Amounts. Insurance coverage shall be at least in the following minimum amounts:
 Professional Liability Insurance: $1,000,000 per occurrence, $2,000,000 aggregate
 General Liability:
 General Aggregate: $2,000,000
 Products Comp/Op Aggregate $2,000,000
 Personal & Advertising Injury $1,000,000
 Each Occurrence $1,000,000
 Fire Damage (any one fire) $ 50,000
 Medical Expense (any 1 person) $ 5,000
 Workers’ Compensation:
 Workers’ Compensation Statutory Limits
 EL Each Accident $1,000,000
 EL Disease - Policy Limit $1,000,000
 EL Disease - Each Employee $1,000,000
 Automobile Liability
 Any vehicle, combined single limit $1,000,000

Page 272 ends

Item # 14.
9 Any available insurance proceeds broader than or in excess of the specified minimum insurance coverage requirements or limits shall be available to the additional insured.

Furthermore, the requirements for coverage and limits shall be the greater of (1) the minimum coverage and limits specified in this Agreement, or (2) the broader coverage and maximum limits of coverage of any insurance policy or proceeds available to the named insured.

13.4. General Liability Insurance. Commercial General Liability Insurance shall be no less broad than ISO form CG 00 01. Coverage must be on a standard Occurrence form.

Claims-Made, modified, limited or restricted Occurrence forms are not acceptable.

13.5. Worker’s Compensation Insurance. Consultant is aware of the provisions of Section 3700 of the Labor Code which requires every employer to carry Workers’ Compensation (or to undertake equivalent self-insurance), and Consultant will comply with such provisions before commencing the performance of the work of this Agreement. If such insurance is underwritten by any agency other than the State Compensation Fund, such agency shall be a company authorized to do business in the State of California. If Consultant is an individual and has no employees, the Project Administrator may accept an affirmation of that fact in lieu of proof of workers compensation insurance.

13.6. Automobile Liability Insurance. Covered vehicles shall include owned, if any, nonowned, and hired automobiles and trucks.

13.7. Professional Liability Insurance or Errors & Omissions Coverage. The deductible or self-insured retention may not exceed $50,000. If the insurance is on a Claims-Made basis, the retroactive date shall be no later than the commencement of the work.

Coverage shall be continued for two years after the completion of the work by one of the following: (1) renewal of the existing policy; (2) an extended reporting period endorsement; or (3) replacement insurance with a retroactive date no later than the commencement of the work under this Agreement.

The Project Administrator may, in his or her sole discretion, waive the requirement for Professional Liability Insurance by initialing here:

Initials: _________________
Name: __________________

13.8. Claims-Made Policies. If any of the required policies provide coverage on a claimsmade basis, the Retroactive Date must be shown and must be before the date of this Agreement or the beginning of work under this Agreement. Claims-Made Insurance must be maintained, and evidence of insurance must be provided for at least five (5) years after completion of work under this Agreement. If coverage is canceled or nonrenewed, and not replaced with another claims-made policy form with a Retroactive Date prior to the effective date of this Agreement, the Consultant must purchase

Page 273 ends

Item # 14.
10 “extended reporting” coverage for a minimum of five (5) years after completion of work under this Agreement.

13.9. Additional Insured Endorsements. The City, its City Council, Commissions, officers, and employees must be endorsed as additional insureds for each policy required herein, other than Professional Errors and Omissions and Worker’s Compensation, for liability arising out of ongoing and completed operations by or on behalf of the Consultant. Consultant’s insurance policies shall be primary as respects any claims related to or as the result of the Consultant’s work. Any insurance, pooled coverage or self-insurance maintained by the City, its elected or appointed officials, officers, agents, employees, volunteers, or consultants shall be non-contributory. All endorsements shall be signed by a person authorized by the insurer to bind coverage on its behalf. General liability coverage can be provided using an endorsement to the Consultant’s insurance at least as broad as ISO Form CG 20 10 11 85 or both CG 20 10 and CG 20 37.

13.10. Failure to Maintain Coverage. In the event any policy is canceled prior to the completion of work under this Agreement and the Consultant does not furnish a new certificate of insurance prior to cancellation, City has the right, but not the duty, to obtain the required insurance and deduct the premium(s) from any amounts due the Consultant under this Agreement. Failure of the Consultant to maintain the insurance required by this Agreement, or to comply with any of the requirements of this Section, shall constitute a material breach of this Agreement.

13.11. Notices. Consultant shall provide immediate written notice if (1) any of the required insurance policies is terminated; (2) the limits of any of the required policies are reduced; (3) or the deductible or self-insured retention is increased. Consultant shall provide no less than 30 days’ notice of any cancellation or material change to policies required by this Agreement. Consultant shall provide proof that cancelled or expired policies of insurance have been renewed or replaced with other policies providing at least the same coverage. Such proof will be furnished at least two weeks before expiration of the coverages. The name and address for Additional Insured Endorsements, Certificates of Insurance and Notices of Cancellation is: City of Grass Valley, Attn: [insert department or individual], 125 East Main Street, Grass Valley, CA 95945.

13.12. Consultant’s Insurance Primary. The insurance provided by Consultant, including all endorsements, shall be primary to any coverage available to City. Any insurance or self-insurance maintained by City and/or its officers, employees, agents or volunteers, shall be in excess of Consultant’s insurance and shall not contribute with it.

13.13. Waiver of Subrogation. Consultant hereby waives all rights of subrogation against the City. Consultant shall additionally waive such rights either by endorsement to each policy or provide proof of such waiver in the policy itself.

Page 274 ends

Item # 14.
11 13.14. Report of Claims to City. Consultant shall report to the City, in addition to the Consultant’s insurer, all insurance claims submitted to Consultant’s insurer in connection with the services under this Agreement.

13.15. Premium Payments and Deductibles. Consultant must disclose all deductibles and self-insured retention amounts to the City. The City may require the Consultant to provide proof of ability to pay losses and related investigations, claim administration, and defense expenses within retention amounts. Ultimately, City must approve all such amounts before execution of this Agreement.

City has no obligation to pay any premiums, assessments, or deductibles under any policy required in this Agreement. Consultant shall be responsible for all premiums and deductibles in all of Consultant’s insurance policies.

13.16. Duty to Defend and Indemnify. Consultant’s duties to defend and indemnify City under this Agreement shall not be limited by the foregoing insurance requirements and shall survive the expiration of this Agreement or its early termination.

14. MUTUAL COOPERATION

14.1. City Cooperation in Performance. City shall provide Consultant with all pertinent data, documents and other requested information as are reasonably available for the proper performance of Consultant’s services under this Agreement.

14.2. Consultant Cooperation in Defense of Claims. If any claim or action is brought against City relating to Consultant’s performance in connection with this Agreement, Consultant shall render any reasonable assistance that City may require in the defense of that claim or action.

15. NOTICES
Any notices, bills, invoices, or reports required by this Agreement shall be deemed received on: (i) the day of delivery if delivered by hand, facsimile or overnight courier service during Consultant’s and City’s regular business hours; or (ii) on the third business day following deposit in the United States mail if delivered by mail, postage prepaid, to the addresses listed below (or to such other addresses as the parties may, from time to time, designate in writing).

If to City:
[Name]
City of Grass Valley
[Department/Division]
125 E Main Street
Grass Valley, CA 95945
Telephone: (530) 274-[XXXX]
Facsimile: (530) 274-4399
If to Consultant:
[Name]
[Address]
[Address]
Telephone:

Facsimile:

Page 275 ends

Item # 14.
12 With courtesy copy to:

Michael G. Colantuono, Esq.

Grass Valley City Attorney
Colantuono, Highsmith & Whatley, PC
420 Sierra College Drive, Suite 140
Grass Valley, CA 95945
Telephone: (530) 432-7357
Facsimile: (530) 432-7356

16. SURVIVING COVENANTS
The parties agree that the covenants contained in Section 6.11 (Records), Section 11.4 (Indemnification of CalPERS Determination), Section 12 (Indemnification), Section 13.8 (ClaimsMade Policies), Section 14.2 (Consultant Cooperation in Defense of Claims), and Section 19.1 (Confidentiality) of this Agreement shall survive the expiration or termination of this Agreement.

17. TERMINATION

17.1. City Termination. City may terminate this Agreement for any reason on five calendar days’ written notice to Consultant. Consultant agrees to cease all work under this Agreement on or before the effective date of any notice of termination. All City data, documents, objects, materials or other tangible things shall be returned to City upon the termination or expiration of this Agreement.

17.2. Consultant Termination. Consultant may terminate this Agreement for a material breach of this Agreement upon 30 days’ notice to allow City time to procure replacement services.

17.3. Compensation Following Termination. Upon termination, Consultant shall be paid based on the work satisfactorily performed at the time of termination. In no event shall Consultant be entitled to receive more than the amount that would be paid to Consultant for the full performance of the services required by this Agreement. The City shall have the benefit of such work as may have been completed up to the time of such termination.

17.4. Remedies. City retains all available legal and equitable remedies for Consultant’s breach of this Agreement.

18. INTERPRETATION OF AGREEMENT

18.1. Governing Law. This Agreement shall be governed and construed in accordance with the laws of the State of California.

Page 276 ends

Item # 14.
13 18.2. Integration of Exhibits. All documents referenced as exhibits in this Agreement are hereby incorporated into this Agreement. In the event of any material discrepancy between the provisions of this Agreement and its exhibits, the provisions of this Agreement shall prevail. This instrument contains the entire Agreement between City and Consultant with respect to the transactions contemplated herein. No other prior oral or written agreements are binding upon the parties. Amendments hereto or deviations from this Agreement shall be effective and binding only if made in writing and executed by City and Consultant.

18.3. Headings. The headings and captions appearing at the commencement of the sections hereof, and in any paragraph thereof, are for convenience of reference to this Agreement. Should there be any conflict between such heading, and the section or paragraph thereof at the head of which it appears, the language of the section or paragraph shall govern in the construction of this Agreement.

18.4. Pronouns. Masculine or feminine pronouns shall be substituted for the neuter form and vice versa, and the plural shall be substituted for the singular form and vice versa, in any place or places herein in which the context requires such substitution(s).

18.5. Severability. If any term or provision of this Agreement or the application thereof to any person or circumstance shall, to any extent, be invalid or unenforceable, then such term or provision shall be amended to, and solely to the extent necessary to, cure such invalidity or unenforceability, and shall be enforceable in its amended form. In such event, the remainder of this Agreement, or the application of such term or provision to persons or circumstances other than those as to which it is held invalid or unenforceable, shall not be affected, and each term and provision of this Agreement shall be valid and be enforced to the fullest extent permitted by law.

18.6. No Presumption Against Drafter. Each party had an opportunity to consult with an attorney in reviewing and drafting this agreement. Any uncertainty or ambiguity shall not be construed for or against any party based on attribution of drafting to any party.

19. GENERAL PROVISIONS

19.1. Confidentiality. All data, documents, discussion, or other information developed or received by Consultant for performance of this Agreement are deemed confidential and Consultant shall not disclose them without prior written consent by the Project Administrator. City shall grant such consent if disclosure is legally required. Consultant shall return all City data to City upon the termination or expiration of this Agreement.

19.2. Conflicts of Interest. Consultant maintains and warrants that it has not employed nor retained any company or person, other than a bona fide employee working solely for Consultant, to solicit or secure this Agreement. Further, Consultant warrants that it has not paid, nor has it agreed to pay any company or person, other than a bona fide employee working solely for Consultant, any fee, commission, percentage, brokerage fee, gift or other consideration contingent upon or resulting from the award or making

Page 277 ends

Item # 14.
14 of this Agreement. Consultant further agrees to file, or shall cause its employees or subcontractors to file, a Statement of Economic Interest under the Political Reform Act with the City’s Filing Officer if required under state law in the performance of the services. For breach or violation of this warranty, City shall have the right to rescind this Agreement without liability. No City Councilmember, officer, or employee of City, during the term of his or her service to City, shall have any direct interest in this Agreement, or obtain any present or anticipated material benefit arising from it.

19.3. Multiple Phased Projects. Pursuant to Government Code section 1097.6, Consultant’s duties and services under this Agreement shall not include preparing or assisting City with any portion of City’s preparation of a request for proposals, request for qualifications, or any other solicitation regarding a subsequent or additional contract with City. City shall at all times retain responsibility for public contracting, including with respect to any subsequent phase of this project. Consultant’s participation in the planning, discussions, or drawing of project plans or specifications, if any, shall be limited to conceptual, preliminary, or initial plans or specifications. Consultant shall cooperate with City to ensure that all bidders for a subsequent contract on any subsequent phase of this project have access to the same information, including all conceptual, preliminary, or initial plans or specifications prepared by Consultant, if any, pursuant to this Agreement.

19.4. Non-assignment. Consultant shall not delegate, transfer, subcontract or assign its duties or rights hereunder, either in whole or in part, without City’s prior written consent, and any attempt to do so shall be void and of no effect. City shall not be obligated or liable under this Agreement to any party other than Consultant.

19.5. Binding on Successors. This Agreement shall be binding on the successors and permitted assigns of the parties.

19.6. No Third-Party Beneficiaries. Except as expressly stated herein, there is no intended third-party beneficiary of any right or obligation assumed by the parties under this Agreement.

19.7. Time of the Essence. Time is of the essence for each and every provision of this Agreement.

19.8. Non-Discrimination. Consultant shall not discriminate against any employee or applicant for employment because of race, sex (including pregnancy, childbirth, or related medical condition), creed, national origin, color, disability as defined by law, disabled veteran status, Vietnam veteran status, religion, age (40 and above), medical condition (cancer-related), marital status, ancestry, or sexual orientation or any other unlawful basis. Employment actions to which this provision applies shall include, but not be limited to, the following: employment, upgrading, demotion, or transfer; recruitment or recruitment advertising; layoff or termination; rates of pay or other forms of compensation; or in terms, conditions or privileges of employment, and

Page 278 ends

Item # 14.
15 selection for training. Consultant shall post this nondiscrimination clause in conspicuous places, available to employees and applicants for employment.

19.9. Waiver. No provision, covenant, or condition of this Agreement shall be deemed to have been waived by City or Consultant unless in writing signed by one authorized to bind the party asserted to have consented to the waiver. The waiver by City or Consultant of any breach of any provision, covenant, or condition of this Agreement shall not be deemed to be a waiver of any subsequent breach of the same or any other provision, covenant, or condition.

19.10. Excused Failure to Perform. Consultant shall not be liable for any failure to perform if Consultant presents acceptable evidence, in City’s sole judgment, that such failure was due to causes beyond the control and without the fault or negligence of Consultant.

19.11. Remedies Non-Exclusive. Each right, power and remedy provided for herein or now or hereafter existing at law, in equity, by statute, or otherwise shall be cumulative and shall be in addition to every other right, power, or remedy provided for herein or now or hereafter existing at law, in equity, by statute, or otherwise. The exercise, the commencement of the exercise, or the forbearance from the exercise by either party of any one or more of such rights, powers or remedies shall not preclude the simultaneous or later exercise by such party of any or all such other rights, powers or remedies.

19.12. Attorneys’ Fees. If legal action shall be necessary to enforce any term, covenant or condition contained in this Agreement, the prevailing party shall be entitled to an award of reasonable and actual attorneys’ fees and costs expended in the action.

19.13. Venue. The venue for any litigation shall be Nevada County, California and Consultant hereby consents to jurisdiction there for purposes of resolving any dispute or enforcing any obligation arising under this Agreement.

19.14. Counterparts; Electronic Signatures. This Agreement may be signed in one or more counterparts, each of which shall be deemed an original, but all of which together shall be deemed one and the same instrument. The parties acknowledge and agree that this Agreement may be executed by electronic signature, which shall be considered as an original signature for all purposes. Without limitation, “electronic signature” shall include faxed or emailed versions of an original signature, electronically scanned and transmitted versions (e.g., via pdf) of an original signature, or a digital signature. [Signature Page Follows]

Page 279 ends

Item # 14.
16 TO EFFECTUATE THIS AGREEMENT, the parties have caused their duly authorized representatives to execute this Agreement on the dates set forth below. [Two signatures are required to bind a corporation]
“City”
City of Grass Valley
By:________________________________
Signature
Tim Kiser
City Manager
Date:______________________
“Consultant”
Wayward Journey
By:________________________________
Signature
Printed:_____________________________
Title:_______________________________
Date:______________________
By:________________________________
Signature
Printed:_____________________________
Title:_______________________________
Date:______________________
Attest:

By:__________________________________
Taylor Whittingslow, City Clerk
Date:_ _______________________________________________
Approved as to form:

By:__________________________________
Michael G. Colantuono, City Attorney
Date:________________________

Page 280 ends

Item # 14.
17 EXHIBIT A

SCOPE OF SERVICES
City Responsibilities
A. Janitorial - All janitorial cleaning will be done by City staff and City volunteers.

B. Animal Husbandry - City is responsible for all of the animal husbandry at the Shelter which includes all of the feeding and cleaning appropriate to all animal species housed at the Shelter.

C. С. Animal Intake - City is responsible for animal intake, including initial health assessment of all animals; Bordetella, DAPP, and general dewormer vaccinations for dogs, and; FVRCP and dewormer vaccinations for cats.

D. Medical - City staff will administer medical protocols in consultation with a veterinarian to all animals within the Shelter, and will be responsible for the medical costs associated with intake and continuing care including all vaccinations, dewormer, and microchips for all cats and dogs, and spay or neuter for all animals. City staff will administer medical care as part of their normal Shelter animal husbandry tasks.

E. Information Technology - City will be responsible for all repair and maintenance of information technology equipment and software used at the Shelter and in connection with Shelter activities, but shall not be responsible for repair, maintenance, or replacement of equipment used solely by Consultant. This includes phones, computers, and hardware associated with the operation of this equipment. Consultant shall not download any programs on equipment which is connected to the City's computer network without the approval of the City's IT Coordinator or their designee.

In the event that Consultant downloads unapproved programs or fails to comply with the City’s technology maintenance and replacement standards, the City may deny access to the City's computer network and may terminate any obligation under this paragraph.

F. Facility Maintenance - City will provide repair and maintenance of the Shelter through City's Facilities Maintenance unit. This includes, but is not limited to, the structure (both interior and exterior), water systems, and HVAC systems.

G. City Front Counter - City will staff the Animal Services front counter as appropriately determined during the open hours of the Shelter. City responsibilities will include but not be limited to: dog licensing, stray animal intake and return, owner relinquishment of animals, and inquiries from the public regarding Animal Services operations.

H. Pet Point Data Management System - City will maintain the Pet Point Data Management System at the Shelter. Consultant will have limited access to the use of this system.

I. Adoptions - City will be responsible for administering and processing all adoptions that occur out of the Shelter. Consultant may run promotions and specials to keep

Page 281 ends

Item # 14.
18 adoptions at a constant flow. Consultant may advertise the animals available for adoption or foster in the Shelter. Advertisements and promotions may include posters, flyers, and electronic communications, among other avenues for publicity.

J. Euthanasia - Except for animals that are irremediably suffering from a serious illness or severe injury per, or otherwise covered by, California Food and Agriculture Code section 17006, City is responsible for destroying animals that City and Consultant deem unadoptable after complying with the statutorily required minimum holding period. Except for animals that are irremediably suffering from a serious illness or severe injury per, or otherwise covered by, California Food and Agriculture Code section 17006, City will give Consultant at least two (2) weeks notice prior to the planned destruction of an animal in order to give Consultant and other animal rescue organizations an opportunity to discuss euthanasia with the City and/or request release of the animal to Consultant or another animal rescue organization pursuant to California Food and Agriculture Code section 31108(b). With Consultant’s consent, City may advance the planned destruction of an animal prior to the fulfillment of the 2 week period.

K. Animal Control Duties - City will be responsible for all animal control related services, procedures, and outcomes.

L. Compliance with State Law - City Shelter staff will be responsible for being familiar with, complying with, and implementing state laws applicable to public animal shelters, including but not limited to California Food and Agriculture Code Division 14, relating to the regulation and licensing of dogs; Division 14.5, relating to the regulation of cats; and Division 14.8, relating to animal facilities and shelters.

Consultant Responsibilities
A. Medical - Consultant may, at its discretion, identify animals for which Consultant will cover the costs of medical care by directly paying the medical provider. This may include medical care provided during intake, as continuing care, or by veterinary specialists (e.g., cardiologists, opthamologists, etc.), or any other type of veterinary care. Animals will be selected for medical coverage depending on various factors, including the animal’s need and Consultant’s budget. When Consultant selects an animal for which Consultant will cover medical costs, Consultant will notify Shelter staff in writing which animals Consultant has selected for medical cost coverage and which of the animal’s costs Consultant will cover.

B. Animal Foster Program - Consultant is responsible for all the needs, excluding food and medical care administered upon intake, of animals that Consultant places into a foster program outside of the Shelter. If the City or Consultant receives an animal that is too young, frail, or a nursing mother, or has any other ailment or issue that shelter living does not accommodate well, Consultant may find temporary foster care for that animal until it is ready to be housed in the Shelter.

C. Humane Education Program - Consultant may provide humane education programs on and off the Shelter site, including but not limited to tours, field trips, summer camps,

Page 282 ends

Item # 14.
19 seminars, and in-class presentations. Consultant must seek and receive City approval prior to holding any program at the Shelter site.

D. Dog Training - Consultant may work directly with positive reinforcement dog trainers to provide structure and training for the dogs awaiting permanent homes. Consultant may also provide opportunities for training for dogs adopted through Consultant.

E. Troubleshooting - Consultant may provide trouble-shooting services to anyone looking to relinquish an animal within and outside of the City's jurisdiction, with the intent of keeping the animals in their homes, rather than relinquishing them to the Shelter.

F. Pet Pantry - Consultant may, at its sole expense, run a Pet Pantry Program, providing free pet food to community members who cannot otherwise afford to feed their animals. Consultant may work directly with the City to ensure proper food storage and distribution.

G. Special Events - Consultant may host special events on an ongoing basis throughout each year. Consultant anticipates that most of these events will be at off-site locations and will not utilize Shelter space with the exception of storage. Consultant shall provide the City with advance written notice and request City approval prior to planning and execution of any event that will be held at the Shelter.

H. Fundraising - Consultant will consistently work to raise funds for the organization.

Fundraising may include but is not limited to mailings, special events, merchandise sales, donation requests, holiday appeals, etc.

I. Volunteer Program - Consultant will hold responsibility for its volunteers on site and off site while on their volunteer shift. Volunteers have approval from the City to provide services for Shelter animals including but not limited to dog walking, cat socialization, and taking Shelter animals to events. Volunteers may also support the Shelter with administrative tasks at the front counter, transporting Shelter animals, and other services. Volunteers that will be in and around the shelter are to be approved by both Consultant and City.

Page 283 ends

Grass Valley City CouncilApril 8, 2025

Grass Valley City Council
April 8, 2025