Agenda packet — Milpitas City Council, March 17, 2026 (part 2 of 6)

0838512
SP
WI, Roof

ROOF CONFIGURATION
The roof of the body will be provided with
two (
2 )
recessed area(s) located
as far forward as
possible, spanning the full width of the body
. The rest of the roof will be flat without any recessed items.

Recessed Area
The recessed area will be constructed of

0.125
" aluminum treadplate and will have two (
2 )

1.00 "
diameter drain holes. The drains will be routed to drain below the body.

The recessed area will be sized appropriately in order to allow proper mounting space and clearance for all roof mounted equipment where the designated mounting location is the recess on the roof of the body. The recess will be configured so that whenever possible, items mounted in the recess will stow below the roof line of the body. If a piece of equipment is taller than the maximum depth of the recess, that item may protrude above the roof line. 0815993
SP
Doors, Roll-up and Lap, AMDOR,
Side Compartments

SIDE COMPARTMENTS
There will both roll-up style doors and lap style doors installed on the side compartments. A total of
two (
2 ) compartment doors
will be roll-up style doors. The roll-up style doors will be located

FORWARD LS/RS COMPARTMENTS
. All other side compartment doors will be lap style doors.

Roll-up Door Compartments
The roll-up doors will be double faced, aluminum construction, painted one (
1 ) color to match the
lower portion of the body
manufactured by AMDOR
™
brand roll-up doors.

The door will be constructed using

1.00 " extruded double wall aluminum slats which will feature a flat smooth interior surface to provide maximum protection against equipment hang-up. The slats will be connected with a structural driven ball and socket hinge designed to provide maximum curtain diaphragm strength. Mounting and adjusting the curtain will be done with a clip system that connects the curtain to the balancer drum allowing for easy tension adjustment without tools.

The slats will be mounted in reusable slat shoes with positive snap-lock securement.

Each slat will incorporate weather tight recessed dual durometer seals. One ( 1 ) fin will be
designed to locate the seal within the extrusion. The other fin will serve as a wiping seal which will also allow for compression to prevent water ingression.

The door will be mounted in a one (
1 )-piece aluminum side frame with recessed side seals to minimize seal damage during equipment deployment. All seals including side frames, top gutters and bottom panel are to be manufactured utilizing non-marring materials.

The bottom panel flange of roll-up door will be equipped with two ( 2 ) cut-outs to allow for easier
access with gloved hands.

A
A polished stainless steel lift bar with locking key latches to be provided for each roll-up door.

The keys to be Model
1250
to match all compartment doors
. The lift bar will be located at the
bottom of door with striker latches installed at the base of the side frames. Side frame mounted door strikers will include support beneath the stainless steel lift bar to prevent door curtain bounce, improve bottom seal life expectancy and to avoid false door ajar signals.

All injection molded roll-up door wear components will be constructed of Type 6 Nylon.

The door will have a

3.00 " diameter ballancer/tensioner drum to assist in lifting the door (garage door style).

The header for the roll-up door assembly will not exceed

4.00 ".

A heavy-duty magnetic switch will be used for control of "open compartment door" warning lights.

Lap Door Compartments
All hinged compartment doors will be lap style with double panel construction and fabricated of

0.09 ",
5052
H
34 aluminum. Doors will be a minimum of

1.50 " thick with a full interior panel. A "C"
section reinforcement will be installed between the outer and interior panels.

Doors will be provided with a closed cell rubber gasket around the surface that laps onto the body. A second heavy-duty automotive rubber molding with a hollow core will be installed on the door framing that seals onto the interior panel.

All compartment doors will have a polished stainless steel continuous hinge, with a pin diameter of

0.25 ", that is bolted or screwed on with stainless steel fasteners. A strip of isolation tape will be furnished between the hinge and the door jamb.

All door lock mechanisms will be fully enclosed within the door panels.

Doors will be latched with recessed, polished stainless steel "D" ring handles and Eberhard 106

locks.

A rubber gasket will be provided between the "D" ring handle and the door 0836038
SP
28' Body Roll and Lap Doors,

28.60.60.Tandem.60, WI, 2-Door No
Crew Cab

EXTERIOR COMPARTMENTS
The exterior compartment layout, dimensions and requirements will be minimum specifications.

The doors will be able to withstand years of rugged service and wear. For this reason, the compartment door design, metal thickness and attachments will be strictly adhered to. The compartment will be constructed of .
125
" (
3 mm)-corrosion resistant aluminum alloy, including all interior panels, floor and sides. The assemblies will be held inside fixtures while being welded.

Compartment flooring will be of the sweep out design with the floor higher than the compartment door frame. All compartments will be supported on top, rear and bottom. The rear wall of each exterior compartment will be welded to the cross sills. Drip protection will be provided over all door openings with an integral roof extrusion or aluminum extrusion.

WHEEL WELLS
The rear fenders will be an integral part of the body sides and compartments. The inside of the fender will be fitted with a full circular inner fender liner. All screws and bolts, which protrude into a compartment, will have acorn nuts attached.
35 959
Bid #:

Page 92 of 555 ends

0837378
SP
Left Forward Compt, 28" Roll & 60" &
60", Roll and Lap, WI, 2-Door Cab

LEFT FORWARD COMPARTMENTS
First Compartment (Transverse)
The first compartment will be located directly behind the cab and above the radius of the front wheelwell. The compartment will be provided with a full-height roll-up door.

Dimensions of First Compartment
Width
Door Frame Opening:

28.00 " wide; Clear Door Opening:

26.50 " wide; Interior Compartment
Width:

30.88 " wide
Height
Door Frame Opening:

42.00 " high; &#x
0 D; Clear Door Opening:

37.00 " high; &#x
0 D; Interior
Compartment Height:

44.88 " high
The compartment will be fully transverse. The full Interior Compartment Height will extend over the frame rails through to the other side of the body. The area over the frame rails will be

30.88 "
wide.

The floor in this compartment will be

3.00 " above the lower door frame.

Second Compartment
The second compartment will be located below the first compartment and behind the front wheel.

The compartment will be provided with a single, vertically hinged lap door.

Dimensions of Second Compartment
Width
Door Frame Opening:

18.00 " wide; Clear Door Opening:

16.50 " wide; Interior Compartment
Width:

18.25 " wide
Height
Door Frame Opening:

19.25 " high; &#x
0 D; Clear Door Opening:

14.50 " high; &#x
0 D; Interior
Compartment Height:

18.38 " high
Third Compartment
The third compartment will be located behind the first and second compartments. The compartment will be provided with vertically hinged, double lap doors.

Dimensions of Third Compartment
Width
Door Frame Opening:

60.00 " wide; Clear Door Opening:

58.50 " wide; Interior Compartment
Width:

62.50 " wide
Height
Door Frame Opening:

64.75 " high&#x
0 D; Clear Door Opening:

63.00 " high&#x
0 D; Interior
Compartment Height:

66.88 " high
Fourth Compartment
The fourth compartment will be located behind the third compartment and directly ahead of the rear wheels.The compartment will be provided with vertically hinged, double lap doors.

Dimensions of Fourth Compartment
Width
Door Frame Opening:

60.00 " wide; Clear Door Opening:

58.50 " wide; Interior Compartment
Width:

62.50 " wide
Height
Door Frame Opening:

64.75 " high&#x
0 D; Clear Door Opening:

63.00 " high&#x
0 D; Interior
Compartment Height:

66.88 " high
Compartment Loading
The first compartment will be capable of holding
800
lb. The area over the frame rails in the first
compartment will be capable of holding an additional
1,000
lb. The second compartment will be
capable of holding
300
lb. The third and fourth compartments will each be capable of holding 1,400
lb.
0515810
Left Over Wheel Compt, 51.50"-

51.50", Roll Door, Tandem, WI

LEFT OVER WHEEL COMPARTMENTS
Forward Compartment
A compartment will be provided above the forward tandem wheels. The compartment will be provided with a full-height roll-up door.

Dimensions of Forward Compartment
Width
Door Frame Opening:

51.50 " wide; Clear Door Opening:

49.00 " wide; Interior Compartment
Width:

54.38 " wide
Height
Door Frame Opening:

27.25 " high; &#x
0 D; Clear Door Opening:

22.25 " high; &#x
0 D; Interior
Compartment Height:

30.13 " high
Rear Compartment
A compartment will be provided above the rear tandem wheels. The compartment will be provided with a full-height roll-up door.

Dimensions of Rear Compartment
Width
Door Frame Opening:

51.50 " wide; Clear Door Opening:

49.00 " wide; Interior Compartment
Width:

57.00 " wide
Height
Door Frame Opening:

27.25 " high&#x
0 D; Clear Door Opening:

22.25 " high&#x
0 D; Interior
Compartment Height:

30.13 " high
Compartment Loading
Each compartment will be capable of holding
1,200
lb.
36 959
Bid #:

Page 93 of 555 ends

0026105
Left Rear Compt, 60" Roll, WI

LEFT REAR SIDE COMPARTMENT
The left rear side compartment will be located directly behind the rear wheels. The compartment will be provided with a full-height roll-up door.

Dimensions of Left Rear Side Compartment
Width
Door Frame Opening:

60.00 " wide; Clear Door Opening:

57.50 " wide; Interior Compartment
Width:

62.50 " wide
Height
Door Frame Opening:

56.00 " high; &#x
0 D; Clear Door Opening:

50.00 " high; &#x
0 D; Interior
Compartment Height:

58.88 " high
Compartment Loading
The compartment will be capable of holding
1,400
lb.
0837379
SP
Right Forward Compt, 28" Roll & 60"
& 60", Roll and Lap, WI, 2-Door Cab

RIGHT FORWARD COMPARTMENTS
First Compartment (Transverse)
The first compartment will be located directly behind the cab and above the radius of the front wheelwell. The compartment will be provided with a full-height roll-up door.

Dimensions of First Compartment
Width
Door Frame Opening:

28.00 " wide; Clear Door Opening:

26.50 " wide; Interior Compartment
Width:

30.88 " wide
Height
Door Frame Opening:

42.00 " high; &#x
0 D; Clear Door Opening:

37.00 " high; &#x
0 D; Interior
Compartment Height:

30.88 "
wide.

The floor in this compartment will be

3.00 " above the lower door frame.

Second Compartment
The second compartment will be located below the first compartment and behind the front wheel.

The compartment will be provided with a single, vertically hinged lap door.

Dimensions of Second Compartment
Width
Door Frame Opening:

18.00 " wide; Clear Door Opening:

16.50 " wide; Interior Compartment
Width:

18.25 " wide
Height
Door Frame Opening:

19.25 " high; &#x
0 D; Clear Door Opening:

14.50 " high; &#x
0 D; Interior
Compartment Height:

18.38 " high
Third Compartment
The third compartment will be located behind the first and second compartments. The compartment will be provided with vertically hinged, double lap doors.

Dimensions of Third Compartment
Width
Door Frame Opening:

60.00 " wide; Clear Door Opening:

58.50 " wide; Interior Compartment
Width:

62.50 " wide
Height
Door Frame Opening:

64.75 " high&#x
0 D; Clear Door Opening:

63.00 " high&#x
0 D; Interior
Compartment Height:

Dimensions of Fourth Compartment
Width
Door Frame Opening:

60.00 " wide; Clear Door Opening:

58.50 " wide; Interior Compartment
Width:

62.50 " wide
Height
Door Frame Opening:

64.75 " high&#x
0 D; Clear Door Opening:

63.00 " high&#x
0 D; Interior
Compartment Height:

Page 94 of 555 ends

0515814
Right Over Wheel Compt, 51.50"-

51.50", Roll Door, Tandem, WI

RIGHT OVER WHEEL COMPARTMENTS
Forward Compartment
A compartment will be provided above the forward tandem wheels. The compartment will be provided with a full-height roll-up door.

Dimensions of Forward Compartment
Width
Door Frame Opening:

51.50 " wide; Clear Door Opening:

49.00 " wide; Interior Compartment
Width:

54.38 " wide
Height
Door Frame Opening:

27.25 " high; &#x
0 D; Clear Door Opening:

22.25 " high; &#x
0 D; Interior
Compartment Height:

30.13 " high
Rear Compartment
A compartment will be provided above the rear tandem wheels. The compartment will be provided with a full-height roll-up door.

Dimensions of Rear Compartment
Width
Door Frame Opening:

51.50 " wide; Clear Door Opening:

49.00 " wide; Interior Compartment
Width:

57.00 " wide
Height
Door Frame Opening:

27.25 " high&#x
0 D; Clear Door Opening:

22.25 " high&#x
0 D; Interior
Compartment Height:

30.13 " high
Compartment Loading
Each compartment will be capable of holding
1,200
lb.
0026109
Right Rear Compartment, 60" Roll,
WI

RIGHT REAR SIDE COMPARTMENT
The right rear side compartment will be located directly behind the rear wheels. The compartment will be provided with a full-height roll-up door.

Dimensions of Right Rear Side Compartment
Width
Door Frame Opening:

60.00 " wide; Clear Door Opening:

57.50 " wide; Interior Compartment
Width:

62.50 " wide
Height
Door Frame Opening:

56.00 " high; &#x
0 D; Clear Door Opening:

50.00 " high; &#x
0 D; Interior
Compartment Height:

58.88 " high
Compartment Loading
The compartment will be capable of holding
1,400
lb.
0026154
Entrance, Rear, 78" Interior Height,
WI

REAR ENTRANCE TO BODY INTERIOR
A single rear entrance door will be provided at the rear of the body. The frame to frame measurement of the rear door opening will be

32.25 " wide and a minimum of

74.00 " high. The
rear door will be constructed of

0.09 ",
5052
aluminum with a full box pan design for strength and
appearance.

Both the interior and exterior door handles will be flush mounted, chrome plated, paddle type door handles.

The outside handle will be located near the bottom of the door, approximately

55.00 " from the
ground, allowing a person of average height to open the door while standing on the ground. The inside door handle will be located approximately half way up the door in the center.

A chrome plated grab handle will be horizontally mounted on the inside of the access door to aid in closing.

The door hinge will be full length polished stainless steel with a

0.25 " stainless steel pin. The
hinge will be attached to the body and door with stainless steel screws or bolts. (hinges that are welded on will not be accepted.) Isolation tape will be furnished between the hinge and the door jam.

The door will be furnished with a stainless steel door grabber to hold the door in the open position.

The door will close on the non-hinged sides with two (
2 ) air cell, hollow core extruded rubber
seals. One (
1 ) seal will be fastened to the door lap and another larger seal fastened to the door opening flange. The bottom seal will be below the flush sweep out walkway. A closed cell rubber seal will be on the hinge side to provide a complete water tight walk-in rescue unit.

If the interior of the body is white laminate, the interior surface of the door will be Pierce #10

white. If the interior of the body is any other material, the interior surface of the door will be Pierce #224
silver.

There will be two (
2 ) windows provided in the door. One (
1 ) window will be located near the top of
the door, and one (
1 ) window will be located near the bottom of the door. Each window will be a half sliding window that measures

17.25 " wide x

14.75 " high. Each window will be provided with
tinted automotive safety glass and a fixed screen on the inside of the window. 38 959
Bid #:

Page 95 of 555 ends

0797082
Interior, Walk-In Body, Floor, Walls,
Ceiling, Countertop

INTERIOR CONSTRUCTION
Interior Floor
The interior floor construction will include a splash shield, sub-floor and finished floor. The splash shield will consist of a metal sheet welded directly to the horizontal floor support tubes.

Above the splash shield, will be a moisture impervious,

0.75 " composite sub-floor panel. The sub-
floor will provide an isolation barrier and bonding medium for the final floor material. The final floor will be covered with
black fleck, coin pattern embossed vinyl
.

The floor will be installed providing a total seal, allowing a complete wash down without any moisture penetrating through to the sub-floor.

Interior Walls/Ceiling
The walkway lower sidewalls (below countertop) will be lined with .
125
" thick aluminum
treadplate
.

The upper side walls (above the counter tops) will be lined with .
25 " thick composite panels with
gray laminate finsh
. The wall covering will include the front and rear walls adjacent to this area.

The ceiling will be lined with
.
25 " thick composite panels with gray laminate finsh
.

Interior Countertop
The countertops (above the exterior compartments) will be constructed of

0.75 " thick composite
material, covered with
a gray laminate finish
overlay. The countertops will be free of any bolts or
screws providing a smooth finished surface.

Body Insulation
The ceiling and walls will be insulated using two (
2 ) types of insulating materials providing a
combined R-Value range of R
13 -R
17 in the body interior.

0.25 " double sided foil insulation will be installed against the exterior body skin. The material will reduce thermal transfer from the exterior of the body.

Installed over the foil insulation, will be a layer of

1.50 " thick acoustical foam insulation. The foam
insulation will provide an additional thermal barrier and sound deadening properties to the body interior.
0817339
Intermediate Step w/Spcl Depth
Storage Compt for Winch Storage

STEPS
Steps will be provided at the rear entrance door. The steps will consist of the following:

One (
1 ) tailboard step that is constructed of bright aluminum treadplate. The step will be the same width as the interior walkway and

10.00 " deep.

One (
1 ) intermediate step that is constructed of bright aluminum treadplate. The step will be the same width as the interior walkway and

10.00 " deep.

A compartment will be provided in the intermediate step for storage of a portable winch. The compartment will be full width of the entrance and as deep as possible. The frame rails will be shortened by a minimum of

10.00 " in order to provide adequate space for storage of the portable winch. A small recess will be provided at the back of the compartment between the frame rails to store the portable winch receiver tube.

The door of the storage compartment will be a one (
1 ) piece lift-up door that is constructed of
aluminum treadplate. The door will be comprised of the riser and tread of the intermediate step along with the riser of the step located directly above the intermediate step. The door will be provided with a D-ring handle located in the riser of the intermediate step. 0644245
Lights, Interior, 12 VDC, Rom
Durolumen R03851, White LED

LED INTERIOR CEILING LIGHTS
There will be
six (
6 )
Rom Model Durolumen R
03851
white LED,
12 volt lights recessed in the
ceiling of the body interior.

The lights will be equally distributed throughout the body interior providing light to the center walkway.
0554033
Switch, Ceiling Lights, HDR Walk-In

SWITCH FOR CEILING LIGHTS
The primary ceiling lights will be actuated by
an automatic switch actuated with the door and a
12 volt rocker switch near the entrance inside the body .
39 959
Bid #:

Page 96 of 555 ends

0821099
Seat, Bench, Side Facing, Lift Up
w/Storage

SIDE FACING LIFT-UP BENCH SEAT WITH STORAGE
A bench seat with storage enclosure will be provided in the interior of the body. The bench seat will be positioned so that it faces the side of the body. The bench seat will be located

LEFT SIDE

OF THE WALKWAY
.

The bench will be designed with seating for a total of
three (
3 )
primary and secondary seats .

Each person will have a separate bottom cushion and separate backrest cushion. Each bottom cushion will be a

22.00 " wide padded cushion that is sized to provide a minimum of

15.00 " from
the front of the cushion to the face of the backrest. Each bottom cushion will be provided with a seat sensor that is connected to the on-board seat belt monitoring system. Each backrest will be a

22.00 " wide x

18.50 " high padded cushion.

The seat cushions will be mounted on top of the storage enclosure. Each cushion will be hinged along the back to provide a means of access to the contents of the storage enclosure. If the bench has more than one (
1 ) seat, multiple seats will be hinged together as a set so they can be lifted together in a single motion. Each set of hinged seats will consist of no more than four ( 4 )
seats. Bench seats with more than four (
4 ) seats will be provided with multiple sets of hinged seats (e.g. an
8 person bench seat will have two (
2 ) sets of hinged seats).

An automatic retractor type seat belt will be furnished at each seat cushion. An extension will be provided with the seat belt so the male end can be easily grasped and the female end easily located while sitting in a normal position.

The upholstery for both the seat cushion(s) and the backrest(s) will be made of 36 oz dark silver
gray vinyl
material.

Seats on this bench will hereafter be referred to in sequential order, starting with Seat 1 and
continuing in ascending order for the number of seats desired (Seat 1 , Seat
2 , Seat
3 , etc). Seat
1 will be the seat that is nearest the front of the body.

NFPA
1900

2024
section

3.3.70 defines primary seating as "designated by the purchaser to be used by firefighters wearing personal protective clothing and equipment as the apparatus is used in regular service".

NFPA
1900

2024
Section

11.1.9.1.1 states primary seating will have a minimum clear width of

20.80 " at the hip level and

27.60 " at the shoulder level.

There will be
three (
3 )
of the total seats designated as primary seat(s).

The primary seats will be located

L/S WALKWAY
.

NFPA
1900

2024
section

3.3.71 defines secondary seating as "any seating position other than a designated primary seating position that is not intended to be occupied as the vehicle is used in regular service and not intended to be used by firefighters wearing protective clothing".

NFPA
1900

2024
Section

11.1.9.1.2 states secondary seating will have a minimum clear width of

20.00 " at the hip level and

22.00 " at the shoulder level.

There will be
zero (
0 )
of the total seats designated as secondary seat(s).

The secondary seats will be located
N/A
.

Storage Enclosure
The storage enclosure will be constructed of
.
125
" thick aluminum treadplate
. The storage
enclosure will be designed to contain an equipment storage rack (equipment and storage racks separately). The length, width, and/or height of the storage enclosure may change in order to accommodate items that are requested to be stored in the rack. At a minimum, the storage enclosure will be

18.00 " deep x

18.00 " high with an overall width that measures approximately

22.50 " wide for each bench seat occupant up to full width of the interior.

There will be
one (
1 ) vertically hinged door on the end of the end of the storage enclosure that faces the rear of the body. The door shall be provided with a flush lift and turn latch. .
0770299
Air Conditioning(15K) w/Heat(6K),
120V Coleman Mach 8, Roughneck,
Rooftop, BLK

HEATING AND AIR CONDITIONING
There will be
one (
1 )
, Coleman Mach
8 Roughneck,
120
volt low profile air conditioning unit(s)
installed on the body roof
in the recess front of the body
. Each air conditioner will have cooling
capacity of
15,000
BTU, heating capacity of
6000
BTU, and include a condensate pump and
hose to prevent accumulation of condensate on the roof. This air conditioning unit only comes in black.

This air conditioner will be powered from the
onboard generator to shoreline power transfer
switch
.

Control will be via
A wall mounted digital thermostat capable of controlling the rooftop air conditioner with electric heat element
.

Each unit will have an overall height of

8.25 " and weigh
92 lb.
0055031
Bracket, SCBA, ZICO Universal
w/CRS

SCBA BRACKET
A Zico SCBA bracket with a footplate and collision restraint strap will be provided.

A total of
three (
3 )
will be provided

AT THE REHAB SEATS
.
0534542
Cabinet, Interior, Upper Wall,
Aluminum, Heavy Nylon Web Door,
Up To 72" Wide

UPPER WALL CABINET
There will be a total of
four (
4 )
upper wall cabinet(s) provided in the interior of the body. Each cabinet will extend from the counter top to the ceiling, will be

24.00 " deep and will be as wide as
possible up to a maximum width of

72.00 ". The cabinet(s) will be constructed of

0.75 " composite
material and covered with

0.12 " aluminum on both sides, bottom and back wall. The aluminum will have a
brushed aluminum
finish.

Heavy black nylon webbing made of

1.00 " nylon strap sewn in a

2.00 " box pattern will be
provided at the cabinet door opening. The nylon webbing will be permanently mounted at the bottom of the cabinet. The top and sides will be secured with mechanical buckles allowing the webbing to be completely removed from the cabinet storage area.

The cabinet(s) located

TWO EACH SIDE, EXACT LOCATION AT PRECON
.
40 959
Bid #:

Page 97 of 555 ends

0534873
Cabinet, Interior, Full Height, Heavy
Nylon Web Door, Up To 48" Wide

FULL HEIGHT CABINET
A full-height cabinet with heavy nylon web door will be provided in the interior of the body. The cabinet will be

24.00 " deep. The height of the cabinet will span the full height of the interior from the floor to the ceiling. The width of the cabinet will be as wide as possible up to a maximum of

48.00 " wide.

The cabinet will be constructed from a composite material with a finish that matches or compliments the interior of the body.

Heavy black nylon webbing will be provided at the cabinet door opening. The webbing will be made of

1.00 " nylon strap and sewn a

2.00 " box pattern. The webbing will be permanently
mounted at the bottom of the cabinet. The top and sides will be secured with mechanical buckles allowing the webbing to be completely removed from the cabinet storage area.

There will be
one (
1 )
cabinet(s) provided. The cabinet(s) will be located

FORWARD PORTION

OF THE WALK IN AREA, KEEP THE CEILING CLEAR FOR THE AC
.
0678353
Lights, Exit Indicator, Wln
RSR02ZCR Red, RSG02ZCR Green,
Spcl Label 1st

EXIT INDICATORS
There will be one (
1 ) Whelen Model RSR
02 ZCR
12 volt DC red LED light with clear lens and
chrome flange included in the body interior:

This light will be activated when the battery switch is on, the ignition switch is on and the parking brake is released.

This light will be labeled "Do Not Exit".

There will be one (
1 ) Whelen Model RSG
02 ZCR
12 volt DC green LED light with clear lens and
chrome flange included in the body interior:

This light will be activated when the battery switch is on, the ignition switch is on and the parking brake is applied.

This light will be labeled "OK To Exit".

This pair of lights will be located

PER DIRECTION AT THE PRECON
.
0004416
Handrail On Ceiling

CEILING HANDRAIL
Mounted on the ceiling of the body interior will be a rigidly mounted handrail. The handrail will be an anodized aluminum extrusion with a ribbed design to provide a positive gripping surface.

There will be
three (
3 )
provided

RS CEILING
.
0045063
Escape Hatch, Skylight

ESCAPE HATCH WITH SKY LIGHT
Escape hatch with skylight will be provided in the body roof.

Skylight will contain a single pane of automotive safety glass.

Hatch opening will measure

24.00 " x

30.00 ".

Window will measure

15.00 " x

22.00 ".

Hatch and hatch frame will be constructed from .
125
" aluminum treadplate to match the roof of
the body.

2.00 " high lip will be provided around the perimeter of the opening to prevent moisture from entering the body.

Hatch will be fully welded in place on the body roof.

Hatch cover will have a rubber gasket inside to prevent leakage.

Hatch cover will be secured with two butterfly - style latches and will have two pneumatic cylinders to hold it in the open position.

A "hatch open" indicator light will be provided in the cab.

There will be
two (
2 )
provided.

BEST LOCATION FRONT TO REAR, EVENLY SPACED ON THE ROOF
.
0045020
Shelf, Adjustable, Interior

ADJUSTABLE SHELF IN CABINET
An adjustable shelf will be provided inside an interior cabinet. The shelf will be constructed of

0.188
" thick aluminum with

2.00 " high sides.

The shelf will be as deep and as wide as required for the designated mounting location.

The shelf will be secured within the cabinet by means of adjustable threaded fasteners. These fasteners will slide in an extruded aluminum track to provide height adjustment.

The shelf and tracks will be finished to match the cabinet it is mounted in.

A total of
four (
4 )
will be provided and mounted in the cabinet(s) located

ONE EACH IN EACH

OVERHEAD COMPARTMENT
.
0583283
Window, Sliding w/Escape Feature,
34" x 20"

WINDOW WITH ESCAPE FEATURE
There will be a total of
two (
2 )
emergency escape window(s) provided in the body. Each window will be a half sliding window that measures

34.00 " wide x

20.00 " high. Each window will have
tinted automotive safety glass and a fixed screen on the inside of the window.

Each window will have an escape feature with egress style release handles mounted on each vertical side of the window and a hinge at the top.

The window(s) will be located

CENTER FRONT TO REAR, ONE PER SIDE
.
41 959
Bid #:

Page 98 of 555 ends

0090567
Hitch, Receiver, Sides, Through Body

SIDE HITCH RECEIVERS
There will be one (
1 ) hitch receiver installed through the body fender panel in front of the rear wheels on each side of the body. The hitch receivers will be constructed of heavy steel tubing and reinforced to the apparatus framework.

Each hitch receiver will be tested to provide a
2:1
straight line pull no-yield safety factor over a
maximum load rating of
10,000
lb. As a result, each of these hitch receivers will be capable of retaining a portable winch with a rating of no more than 10,000
lb. Each hitch receiver will also be
capable of being used for rope operations when used with properly rated equipment.

Spring loaded stainless steel doors will be provided on the exterior of the body to cover the ends of receivers in the fender area. Each door will have a flush latch provided to prevent the door from opening while not in use. A stainless steel trim ring will be provided to prevent damage to the exterior finish around the opening.

Access to each receiver pin will be provided through the compartment ahead of the receiver and through the fender liner. A small hinged door will be provided to cover the fender access in order to prevent debris from entering the area of the retaining pin. A rubber cover will be provided to cover the access inside the forward compartment to prevent road dust from entering the compartment.
0629341
Rope Anchors, Pair, 9,000 lb Rating

ROPE ANCHORS
There will be
two (
2 ) pairs
of chrome plated steel eyebolts installed on the body to serve as rope anchor points. Each anchor will have an inside diameter of

2.00 " (
51 mm) and will be supported
to provide a maximum of
9,000
lb (
4,082
kg) no-yield condition with a straight line pull.

Each pair of anchors will be installed in the following locations:

One (
1 ) on each side of the body in the upper corners at the front of the body One (
1 ) on each side of the body in the upper corners at the rear of the body Third pair of rope anchors not requested
Stainless steel scuffplates will be provided behind each anchor point. 0818001
Rope Anchors, Pair, 3,000 lb Rating,
Side of Body, Non-NFPA 2024

ROPE ANCHORS
A total of
two (
2 ) pairs
of chrome plated steel eyebolts will be installed on the sides of the body to serve as rope anchor points. For each pair of rope anchors selected, there will be one ( 1 ) anchor
mounted on each side of the body. Each anchor will have an inside diameter of

2.00 " (
51 mm)
and will be supported to provide a maximum of
3,000
lb (
1,361
kg) no-yield condition with a
straight line pull.

The rope anchors will be positioned
just below the roof line positioned as high as possible on the side sheet
.

The specific location(s) of each pair of rope anchors will be

UPPER SIDE OF BODY PER THE

MARKED UP AD, TWO PER SIDE
.

NFPA
1900
,
2024
edition, section

12.11.2 requires that receivers or anchors installed at any location on the apparatus for use with rope operations will be designed and affixed to the apparatus to provide at least
9,000
lb (
4,082
kg) no-yield condition with a straight line pull. These anchors are not rated for
9,000
lb (
4,082
kg) no yield condition with a straight line pull. Per the customer's specifications and request of these anchors, this apparatus will be non-compliant to the current edition of applicable NFPA standards effective at time of contract execution. 0078804
Trim, Body Seams, Painted IPO Std.

TRIM BODY SEAMS
All body seams will be trimmed with the same material as the body construction and painted to match the body paint.
0815694
Blister, Rear Bulkhead Compt
Ceiling, Raise Interior Compt Height

CEILING BLISTER
The ceiling of a rear bulkhead compartment will be blistered to increase the interior height of the compartment and allow for storage of long equipment. The blister will extend into the area immediately above compartment, thereby reducing the amount of space available in the affected area.

The clear space (from floor of compartment to the extended height) will be

12.25 " less than the
body height if there are no other options to consider.

The blister will increase the height of the interior of the compartment only. The width and depth of the interior along with the compartment door opening will remain as specified.

The affected compartment(s) will be the
left and right
compartment(s).
0075036
Box, Tool, Poly, Custom Size

TOOL BOX
Tool box(es) construction of .
50 " thick plastic with a cut out carrying handle on each end will be provided.

The tool box(es) will be held in place to prevent movement while the vehicle is in motion.

The exterior box dimensions will be
TBD at pre con
.

There will be
ten (
10 )
provided. The tool box(es) will be located
lower section of RS
5 .
0023359
Floor Extension, Compt

FLOOR EXTENSION
There will be a floor extension from the transversed area over the frame to the compartment door. The extension will have a

1.50 " vertical lip and a return bend. The extension will be support by angles off the side partitions of the compartment.

A total of
four (
4 )
will be provided and located
LS
4 , LS
5 , RS
4 , RS
5 .
42 959
Bid #:

Page 99 of 555 ends

0004201
Rack, SCBA Bottles, 7.50" x 7.50"

STORAGE RACK FOR SPARE SCBA BOTTLES
A storage rack will be provided
lower section of LS
5 to hold
ten (
10 )
spare SCBA bottles. The
rack will be built to hold the bottles
5 over
5 horizontal below the floor extension
.

The rack will be constructed of

0.12 " aluminum. The inside of the rack will be left unpainted and the outside of the rack will be painted the same color as the compartment it is installed in. Each storage slot will angle to the rear of the rack in order to minimize the chances of the bottle falling out. A rubber bumper will be provided on the rear wall of each slot to absorb the shock of the bottle being placed into position. Scuff tape material will be applied to the inside of each slot to reduce scratching on the bottle.

The inside dimension of each bottle slot will be

7.50 " x

7.50 ".
0629237
Recess For Reels, Walk In

RECESS FOR REEL
The compartment top will be modified to allow
two (
2 )
reel(s) to be recessed. A removable
enclosure will be installed around the reel bracket.

LS/RS
5 .
0636346
Bumper, Not Required, Walk-In or
Combination Body
0793822
Not Required, Water Tank, Rescue

0023410
Not Required, Overflow

0028107
Not Required, Foam Cell Modification

0013534
Not Required, Running Boards

0690026
Wall, Rear, Body Material, HDR

REAR WALL, BODY MATERIAL
The rear wall will be smooth and the same material as the body. 0532024
SP
Tow Eyes, (2) w/Winch Receiver
Rr/Sides, Under Body,
(Tanker/Rescue)

TOW EYES
Two (
2 ) rear painted "tow" eyes will be located at the rear of the apparatus and will be mounted directly to the chassis frame rails. The inner and outer edges of the tow eyes will be radiused.

PORTABLE WINCH RECEIVER AT THE REAR
A portable winch receiver will be installed at the rear of the apparatus.

The portable winch receiver will be constructed of heavy steel tubing and reinforced to the truck framework, for the receiver
Slide-in portion will be held in place by one (
1 ) safety pin with clip.
12 volt winch power cable will be routed to the receiver.

PORTABLE WINCH RECEIVER AT THE SIDES
A portable winch receiver will be installed at each side of the apparatus, to the rear of the wheels, under the rear platform.

The side portable winch receivers will be constructed of heavy steel tubing and reinforced to the truck framework.

Slide-in portion will be held in place by one (
1 ) safety pin with clip.
12 volt winch power cable will be routed to the receiver. 0556162
Not Req'd, Compt Blister in Front of
Rear Axle
0045159
Guard, Drip Pan, S/S, L-Shape,
Cover Bottom and Rear of Rollup
Door Roll

DOOR GUARD
The
two (
2 ) compartment doors
will include an L-shaped guard designed to protect the bottom and interior side of the roll-up door from damage when in the retracted position and contain any water spray while the door is being opened. The guard will be fabricated from stainless steel and installed
each roll up door
.
0795390
Pull Strap for Rollup Doors, Amdor
Flex-HD

ROLLUP DOOR PULL STRAP
There will be
two (
2 ) compartment doors
provided with Amdor Flex-HD pull straps. The
compartment door(s) to be provided with a pull strap will be

FORWARD COMP EACH SIDE
0611794
Trim, Rollup Door, Painted Door
Color, Amdor

ROLL-UP DOOR TRIM
The exterior of the aluminum trim around the door opening will be painted to match the color of the applicable door.

There will be
two (
2 )
compartments located

FORWARD COMP EACH SIDE
with the trim painted.
43 959
Bid #:

Page 100 of 555 ends

0689547
Lights, Compt, Pierce LED, Dual
Light Strips, Each Side of Door, HDR

COMPARTMENT LIGHTING
There will be
ten (
10 )
compartments with Pierce LED compartment light strips. The strips will be centered vertically along each side of the door framing.

Any remaining compartments will include

6.00 " diameter Truck-Lite, Model:
79384
light in each
enclosed compartment. Each light will have a number
1076
one filament, two wire bulb.

Opening the compartment door will automatically turn the compartment lighting on. 0606056
Lights, Hatch Compt, Not Required,
HDR
0652247
Shelf, Adjustable, 500 lb Capacity,
Standard Depth, HDR

STANDARD DEPTH ADJUSTABLE SHELF
An adjustable shelf will be provided. The shelf will be constructed of

0.188
" thick aluminum with

2.00 " high sides. The shelf will be provided
painted spatter gray
.

The shelf will be as deep as possible for a standard depth compartment, and as wide as possible for the specified mounting location.

The shelf will be secured within the compartment by means of adjustable threaded fasteners.

These fasteners will slide in an extruded aluminum track to provide height adjustment.

The shelf will have a load capacity of
500
lb.

A total of
ten (
10 ) shelves
will be provided
LS
2-3
RS
2-3
RS
1 X
3 , LS
1 X
3 .
0667235
Cable, Single Hand Operation,
Tilt/Slide Out, Utility Trays

SINGLE HANDED CABLE LATCH
A cable will be provided to tie together the two (
2 ) spring loaded locks that are provided as
standard at the front of a slide-out/tilt tray in order to provide single hand operation of the tray.

The single hand operation cable will be provided on a total of eight (
8 ) slide-out trays
located
all
slide out trays
.
0652283
Tray, 250 lb Slide-Out, 2" Sides - Adj.

Height, Standard Depth Compt, HDR

STANDARD DEPTH SLIDE-OUT ADJUSTABLE HEIGHT TRAY
There will be
four (
4 ) slide-out trays
provided.

Each tray will have

2.00 " high sides and a capacity rating of up to
250
lb in the extended position.

Each tray will be as deep as possible for a standard depth compartment and as wide as possible for the specified mounting location.

Each tray will be provided
painted spatter gray
.

Each tray will be mounted on a pair of side mounted slides. The slide mechanisms will have ball bearings for ease of operation and years of dependable service. The slides will be mounted to shelf tracks to allow the tray to be adjustable up and down within the designated mounting location.

An automatic lock will be provided for both the in and out tray positions. The lock trip mechanism will be located at the front of the tray and will be easily operated with a gloved hand.

The tray(s) will be located
LS
2 x
2 LS
3 x
2 .
0646980
Tray, Floor Mounted, Slide-Out,
Standard Depth Compt, 500lb, 2.00"
Sides, HDR

STANDARD DEPTH SLIDE-OUT FLOOR MOUNTED TRAY
There will be
four (
4 )
floor mounted slide-out tray(s) with

2.00 " sides provided
LS
4-5
RS
4-5
.

Each tray will be rated for up to
500
lb in the extended position. The tray(s) will be constructed of

0.19 " aluminum. The finish will be
painted spatter gray
.

Each tray will be mounted on two (
2 ) under mount, roller bearing type slides. Each slide will be rated at
250
lb with a factor of safety of two (
2 ).

To ensure years of dependable service the slides will be coated with a finish that is tested to withstand a minimum of
1,000
hours of salt spray per ASTM B
117
.

To ensure years of easy operation, the slide will require no more than a 50 lb force for push-in or
pull-out movement when fully loaded after having been subjected to a 40 hour vibration (shaker)
test under full load. The vibration drive file will have been generated from accelerometer data collected from a heavy truck chassis driven over rough gravel roads in an unloaded condition.

Proof of compliance will be provided upon request.

Automatic locks will be provided for both the "in" and "out" positions. The trip mechanism for the locks will be located at the front of the tray for ease of use with a gloved hand. 0725634
Cabinet, Drawer Assembly, CTECH,
Four Drawers, Up To 48" Wide, 24"
Deep

DRAWER ASSEMBLY
A slide-out drawer assembly will be installed
LS
4 .

The clear dimensions starting at the top of the cabinet with the first drawer will be

2.00 " with a
face plate that is

3.00 "
high x

21.00 " deep. The clear dimensions of the second drawer will be

5.75 " with a face plate that is

6.00 "
high x

21.00 " deep. The clear dimensions of the third drawer
will be

5.75 " with a face plate that is

6.00 "
high x

21.00 " deep. The clear dimensions of the fourth
drawer will be

5.75 " with a face plate that is

6.00 "
high x

21.00 " deep. Each drawer will be the
same width and not exceed

48.00 ".

The drawers will have a capacity of
250
pounds.

The drawers will be mounted in a cabinet housing constructed of light gray powder coated aluminum with anodized aluminum frames. The housing will be

24.00 " deep, and completely
enclose the drawer.

A full-length aluminum extruded rail will be provided at the top edge of each drawer. This rail will act as the latching mechanism as well as the handle for each drawer.

There will be a total of
one (
1 )
provided.
44 959
Bid #:

Page 101 of 555 ends

0648489
Toolboard, Slide-out, Alum, .188",
Peg Board, Standard Depth, HDR

STANDARD DEPTH SLIDE-OUT TOOLBOARD
A slide-out aluminum toolboard will be provided. The toolboard will be constructed of

0.19 " thick
aluminum that is
painted spatter gray to match compartment interior
. The toolboard will be
provided with

0.20 " diameter holes in a pegboard pattern with

1.00 " centers between holes. A

1.00 " x

1.00 " aluminum tube frame will be welded to the edge of the pegboard. A handhold cutout will be provided on the outboard edge of the toolboard.

The toolboard will be as deep as possible for a standard depth compartment, and as tall as possible for the specified mounting location.

The toolboard will be mounted on an under mount, roller bearing type slide that is rated for 250
lb
with a factor of safety of two (
2 ).

To ensure years of dependable service the slide will be coated with a finish that is tested to withstand a minimum of
1,000
hours of salt spray per ASTM B
117
.

Proof of compliance will be provided upon request.

The slide will be mounted to a shelf type track to allow side adjustment of the tool board.

A positive lock will be provided to allow the toolboard to be locked in both the stowed and extended positions.

A total of
One (
1 )
standard depth slide-out toolboard(s) will be provided. The toolboard(s) will be located
LS
1 , EXACT LOCATION AT PRECON
.
0622249
Toolboard, Alum, Adj, Added to
Standard Depth Slide-Out Tray

TOOLBOARD ADDED TO STANDARD DEPTH SLIDE-OUT TRAY
An aluminum toolboard will be provided and mounted in a standard depth slide-out tray (tray not included). The toolboard will be constructed of

0.19 " thick aluminum that is
painted spatter gray to
match compartment interior
. The toolboard will be provided with

0.20 " diameter holes in a
pegboard pattern with

1.00 " centers between holes. A

1.00 " x

1.00 " aluminum tube frame will be
welded to the edge of the pegboard.

The toolboard will span the full depth of the standard depth slide-out tray and will be as tall as possible for the specified mounting location.

The toolboard will be mounted on aluminum tracks to allow for side-to-side adjustment within the tray.

The total capacity rating of the toolboard will vary depending on the tray it is mounted in (capacity rating for the toolboard will match the capacity rating of the tray it is mounted in).

Four (
4 )
toolboard(s) will be provided and mounted in the slide-out tray(s) located LS/RS
4 LS/RS
5 .
0726451
Partition, Vertical Compt

VERTICAL COMPARTMENT PARTITION
One (
1 ) partition
will be bolted in
LS
2 . Each partition will be the full vertical height of the compartment.
0659383
Matting, Turtle Tile w/Ramp,
Compartment Floors

MATTING, COMPARTMENT FLOOR
Turtle Tile compartment matting will be provided in
seven (
7 )
compartments on the compartment
floor. The locations are,
LS
1 , LS
2 , LS
3 , RS
2 , RS
3 , RS
4 , RS
5 .

The Turtle Tile will be
black
and the leading edge of the matting will include the beveled edge.

The beveled edge will be
black
.
0544203
Matting, Turtle Tile, Hatch
Compartment Floor, Each

MATTING, FLOOR OF HATCH COMPARTMENT
There will be Turtle Tile compartment matting provided on the floor of the designated hatch compartment(s).

The color of Turtle Tile matting will be
black
.

The Turtle Tile matting will be provided on the floor of a total of two (
2 )
hatch compartment(s)
located
each hatch compartment
.
0028026
Matting, Turtle Tile, Compartment
Shelving Only

MATTING, COMPARTMENT SHELVING
Turtle Tile compartment matting will be provided in
13 shelves
. The locations are,
each shelf and
tray
.

The color of the Turtle Tile will be
black
.
0004016
Rub Rail, Aluminum Extruded, Side
of Body

RUB RAIL
Bottom edge of the side compartments will be trimmed with a bright aluminum extruded rub rail.

Trim will be

2.12 " high with

1.38 " flanges turned outward for rigidity.

The rub rails will not be an integral part of the body construction, which allows replacement in the event of damage.
0560198
Fender Crowns, Rear, S/S, 2 Pair,
Wider Than Standard

BODY FENDER CROWNS
Stainless steel fender crowns will be provided around the rear wheel openings. These fender crowns must be wide enough to prevent splashing onto the body from the specified rear tires.

A rubber welting will be provided between the body and the crown to seal the seam and restrict moisture from entering.
0519848
Not Required, Hose, Hard Suction,
No Pump

45 959
Bid #:

Page 102 of 555 ends

0726242
Hopper, Oil Dry, Inside Compartment,
Plexiglass Sight

OIL DRY HOPPER
There will be an oil dry hopper installed in the
RS
1 compartment. A door will be provided on the
top
of the oil dry bin to allow refilling of the bin. The bin will be sized for storage of 150
lb or

25.3 gallons (
5850
cubic inch)
of clay-based oil dry absorbent material. The hopper will have a hand valve on the bottom to control the release of the material. The absorbent material will be discharged through
a PVC tube through the floor of this compartment allowing a bucket to be placed under the truck and filled
.

A plexiglass sight will be provided in the hopper to show oil dry level within the hopper. 0044229
No Extension Ladder Req'd

0074231
No Roof Ladder Required
0074248
Not Required, Folding Ladder

0540739
Not Required, Rack, Equipment
Storage
0756045
Rack, Equipment Storage, Walk-In
Body, Interior

LADDER/EQUIPMENT STORAGE
The apparatus will be equipped with a ladder/long equipment storage rack located in the interior walkway of the body.

The rack will be constructed of
one (
1 ) storage trough
. The troughs will be accessible from the
rear compartment of the body. The storage trough(s) will be arranged allowing equipment to be removed independently without the removal of adjacent equipment.

The storage troughs will be configured

A SINGLE U-SHAPED TROUGH SIZED TO FIT THREE
3/4
" SHEETS OF PLYWOOD,
3 TO THE FRONT AND
3 MORE TO THE REAR OF THE
TRUCK, ALL ON EDGE. MOUNTED AT LEAST

3.00 " FROM THE INTERIOR CABINETS.

STRAPPED TO CABINET.
. The storage trough(s) will be mounted minimizing the forward compartment area required to accommodate the configuration.

The storage configuration will be provided with
a single retaining strap with hook and loop
fastener
to secure and prevent equipment from migrating to the rear of the apparatus while in motion.
0600564
Bell, 12" Chrome w/Eagle, Mounted
on Cab Corner, Vel/Imp

BELL
A chrome plated,

12.00 " bronze cast bell, complete with an eagle, will be mounted on the passenger side radiused corner of cab face. The cab will be properly reinforced to support the weight of the bell. A rope pull, for the bell, will be installed inside the cab. 0838836
Step, Rear, Swing Down, Gas Assist
Cylinders, HDR, MUX

SWING DOWN STEP
A swing down style rear access step will be installed onto the rear tailboard. The step will swing up and stow above the tailboard in the "up" position and swing down for use as a stepping surface in the "down" position.

A chrome plated lift handle will be provided on the underside of the step to aid in raising and lowering the step.

The step will be provided with gas assist cylinders to secure the step in the up and down positions.

The step will be fabricated from polished aluminum treadplate with No Insert
.

Size of Step
Non-Walk-In Body

38.50 " wide x

8.00 " deep
Walk-In Body

31.50 " wide x

8.00 " deep
When the step is in the "down" position, a text message will be displayed on the Vehicle Information Center multiplex display screen that reads "Rear Step Not Stowed".

When deployed, the step will meet the NFPA requirement for minimum stepping height from the ground.
0518339
Not Required, Pump House, Rescue

0092531
Not Required, Pump House Structure

0796159
Not Required, Pump, Rescue

0012216
No Seal/Packing Required

0012690
Not Required, Trans, Pump

46 959
Bid #:

Page 103 of 555 ends

0669703
Not Required, Pumping Mode

0024484
Not Required, Pump Shift

0046295
Transmission Lock-up, Not Req'd,

NO PUMP
0046296
Not Required, Auxiliary Cooling
System, NO PUMP

0046283
Not Required, Transfer Valve, NO
PUMP
0024513
Not Required, Intake Relief Valve

0046403
No Relief Valve Req'd, No Pump

0012336
No Pump Primer Req'd

0012816
Not Required, Pump Manuals

0090789
Not Required, Plumbing, No Pump

0046371
Not Required, No Plumbing or Foam
System
0796254
No Main Inlet Required, Rescue No
Pump
0584002
Not Required, Cap, Main Pump Inlet,
No Side Inlet Caps Required, No
Pump
0089389
No Valves, (No Pump)

0074685
Not Required, Inlet Installation

0064700
Not Required, Inlet Control

0055600
Not Required, Auxiliary Inlet, Left
Side
0029147
Not Required, Inlet, Right Side

0681723
No Bleeder Valve, No Pump

0681730
Not Required, Tank to Pump, No
Pump
0074900
Not Required, Tank Fill

0089394
Not Required, Outlet Control, No
Pump
0551181
Not Required, Outlet, Left Side,
Rescue
47 959
Bid #:

Page 104 of 555 ends

0055095
Not Required, Elbow, Left Side
Outlets, 2.50"
0092570
Not Required, Outlets, Left Side
Additional
0021143
Not Required, Outlet, Right Side

0021134
Not Required, Elbow, Right Side
Outlets, 2.50"
0092571
Not Required, Outlets, Right Side
Additional
0545326
Not Required, Outlet, Large
Diameter, No Pump

0007308
Not Required, Elbow, Large Diameter
Outlet
0092572
Not Required, Outlet, Front
0728255
Not Required, Caps/Plugs for 1.00" to

3.00" Discharges/Inlets

0089391
Valve, Bleeder - None Req'd, (No
Pump)
0029106
Not Required, Deluge Outlet
0029302
No Monitor Requested

0029304
No Nozzle Req'd

0029107
No Deluge Mount

0723726
Speedlay Module Not Required

0722432
Hose Restraint Not Required, No
Speedlay Module
0723395
Speedlays, Not Required

0723394
Speedlays, Not Required

0519936
Not Required, 1.50" Crosslays,
Rescue
0500535
Not Required, Hose Restraint,
Crosslay
0029260
Not Required, Speedlays

0750536
Hose Restr, Spdly, Not Required, No
Spdly
0046372
Not Required, Foam System, Pump,
or Plumbing
0012126
Not Required, CAF Compressor

48 959
Bid #:

Page 105 of 555 ends

0552517
Not Required, Refill, Foam Tank
0042573
Not Required, Foam System
Demonstration

0045465
Not Required, Foam Tanks
0091110
Not Required, Foam Tank Drain
0091079
Not Required, Foam Tank #2

0091112
Not Required, Foam Tank #2 Drain

0738072
Approval Dwg, Pump Panel(s), Not
Required
0000261
Not Required, Pump Panel Layout

0030701
Not Required, Material, Pump
Panels, No Panel

0046495
Not Required, Pump Access, No
Pump
0634458
Not Required, No Chassis Engine
Gauges @ Pump Panel

0046400
Throttle, Engine, Not Required, No
Pump/Skid Pump
0892618
Not Required, Indicator Light, Pump
Panel, No Pump or Skid Pump

0046378
Not Required, Gauges,
Vac/Pressure, No Pump

0046375
Not Required, Gauges, No Pump

0006774
Not Required, Foam Level Gauge
0046280
Not Required, Light Shield, No Pump

0837187
Air Horns, (2) Grover Stuttertone, 6"
Round, In Bumper

AIR HORN SYSTEM
Two (
2 ) Grover air horns will be recessed in the front bumper.

The air horns will be
chrome
.

The air horn system will be piped to the air brake system wet tank utilizing

0.38 " tubing. A
pressure protection valve will be installed to prevent the loss of air in the brake system. 0606834
Location, Air Horns, Bumper, Each
Side, Outside Frame, Inboard (Pos
#2 & #6)
Air Horn Location
The air horns will be located on each side of the bumper, just outside of the frame rails. 0757092
Control, Air Horn, Multi Select

Air Horn Control
The air horn(s) will be activated by the following:
0757080
Control, Air Horn, Ft Sw, RS

Right side foot switch
49 959
Bid #:

Page 106 of 555 ends

0757081
Control, Air Horn, Ft Sw, LS

Left side foot switch
0819024
Siren, Wln 295HFS2 Remote, Single
Amp, Other Speaker, Non-NFPA
2024

ELECTRONIC SIREN
A Whelen
295
HFS
2 , electronic remote siren with noise canceling microphone will be provided.

This siren to be active when the battery switch is on and that emergency master switch is on.

NFPA
1900
,
2024
edition, Section

10.8.1.1 requires the siren manufacturer to certify the siren as meeting the requirements of SAE J
1849
,
Emergency Vehicle Sirens
.

Per the fire department specification, the siren and siren speaker come from separate manufacturers and a certification is therefore not valid. The apparatus will be non compliant to NFPA
1900
standards at time of contract execution.
0510206
Location, Elect Siren, Recessed
Overhead In Console

Electronic siren head will be
recessed in the overhead console above the engine tunnel on the driver side
.
0748306
Control, Elec Siren, Multi Select

ELECTRONIC SIREN CONTROL
The electronic siren will be activated by the following:
0748294
Control, Elec Siren, Ft Sw, LS

The left side foot switch.
0601330
Speaker, (1) Federal, ES100C
w/ESFMT-EF Recess Mnt & S/S
Grille

SPEAKER
There will be one (
1 ) Federal Signal DynaMax®, Model ES
100
,
100
watt speaker provided. The
speaker will use a Federal Signal, Model ESFMT-EF, recess mount with stainless steel grille. The speaker will be
connected to the siren amplifier
.
0601555
Location, Speaker, Frt Bumper,
Recessed, Left Side, Outside
Frame,Outbrd (Pos 7)
The speaker will be recessed in the left side of the front bumper, towards the outside. 0895310
Siren, Federal Q2B

AUXILIARY MECHANICAL SIREN
There will be a Federal Signal Model Q
2 B mechanical siren furnished and installed in the front of the apparatus.

The Q
2 B will be
chrome finish
.

The siren will have a
2 -gauge cable connected to a power solenoid that is connected by a 2 -
gauge cable ran battery direct to the primary chassis batteries and will be labeled Q 2 B+ at the
battery. The power solenoid will only be enabled when the emergency master switch is on.

The siren will have a
2 -gauge ground wire connected to the chassis battery stud. The cable will be labeled Q
2 B- at the battery.
0578974
Siren, Mechanical, Recessed In
Grille, Imp/Vel
The mechanical siren will be mounted recessed in the front grille. The siren mounting will include a reinforcement plate.
0748305
Control, Mech Siren, Multi Select

MECHANICAL SIREN CONTROL
The mechanical siren will be activated by the following:
0748281
Control Mech Siren, Ft Sw RS

Right side foot switch
0748282
Control Mech Siren, Ft Sw LS
Left side foot switch.
0736691
Sw, Siren Brake, Momentary Chrome
Push Button, LS
A momentary chrome push button switch will be included in the left side dash panel to activate the siren brake.
0740391
Sw, Siren Brake, Momentary Chrome
Push Button, RS
A momentary chrome push button switch will be included in the right side dash panel to activate the siren brake.
0002623
Cut-Out, Mech Siren, Interlock to Prk
Brk

MECHANICAL SIREN INTERLOCK
The mechanical siren will be interlocked to shutoff whenever parking brake is applied. The interlock will disconnect the power only.
0746353
Not Required, Warning Lights
Intensity
50 959
Bid #:

Page 107 of 555 ends

0786656
SP
Lightbar, Wln, Freedom IV-Q, 81",
RRRRsrRRRWWRRRsrRRRR

FRONT ZONE UPPER WARNING LIGHTS
There will be one (
1 )

81.00 " Whelen® Freedom
™
IV LED lightbar mounted on the cab roof.

The lightbar will include the following:

One (
1 ) red flashing LED module in the driver's side end position.

One (
1 ) red flashing LED module in the driver's side front corner position.

One (
1 ) red flashing LED module in the driver's side first front position.

One (
1 ) red flashing LED module in the driver's side second front position.

One (
1 ) steady red burning LED module in the driver's side third front position.

One (
1 ) red flashing LED module in the driver's side fourth front position.

One (
1 ) red flashing LED module in the driver's side fifth front position.

One (
1 ) red flashing LED module in the driver's side sixth front position.

One (
1 ) white flashing LED module in the driver's side seventh front position.

One (
1 ) red flashing LED module in the passenger's side sixth front position.

One (
1 ) red flashing LED module in the passenger's side fifth front position.

One (
1 ) red flashing LED module in the passenger's side fourth front position.

One (
1 ) steady red burning LED module in the passenger's side third front position.

One (
1 ) red flashing LED module in the passenger's side second front position.

One (
1 ) red flashing LED module in the passenger's side first front position.

One (
1 ) red flashing LED module in the passenger's side front corner position.

One (
1 ) red flashing LED module in the passenger's side end position.

There will be
clear lenses included on the lightbar
.

There will be a switch installed in the cab on the switch panel to control this lightbar.

The white flashing LED modules will be disabled when the parking brake is applied.

The red flashing LED modules in the front positions may be load managed when the parking brake is applied.
0897602
Light, Front Zone, Wln M6** M6**
M6** M6**, 4 Lts

CAB FACE WARNING LIGHTS
There will be four (
4 ) Whelen®, Model M
6 **,

4.31 " high x

6.75 " wide x

1.37 " deep flashing LED
warning lights with
chrome trim
installed on the cab face, above the headlights.

The
left side outside warning light to include red LEDs
.

The
left side inside warning light to include red LEDs
.

The
right side inside warning light to include red LEDs
.

The
right side outside warning light to include red LEDs
.

The
warning light lens color(s) to be clear
.

The lights will be controlled per the following:

A switch in the cab on the switch panel will control the lights.

White LED will be deactivated when the parking brake is applied.

Amber LEDs will be activated when the parking brake is applied.

Amber, blue, green or red LEDs in the inside positions may be load managed when the parking brake is applied.
0558676
Daytime Running Lights, Headlights,
Vel/Imp, Enf/AXT-MUX, (Low Beam)

DAYTIME RUNNING LIGHTS (HEADLIGHTS)
The low-beam headlights used as daytime running lights will be activated with the following measures:

Ignition switch is turned on
Parking brake is released
These lights will be deactivated with any one of the following measures:

Headlight switch is turned on
High-beam flash is turned on
Parking brake is set
0653937
Flasher, Headlight Alternating

HEADLIGHT FLASHER
The high beam headlights will flash alternately between the left and right side.

There will be a switch installed in the cab on the switch panel to control the high beam flash. This switch will be live when the battery switch and the emergency master switches are on.

The flashing will automatically cancel when
the hi-beam headlight switch is activated
or when the
parking brake is set.
0540692
Lights, Side Zone Lower, Wln M6*C
LED, Clear Lens, 3pr, Ovr 25

SIDE ZONE LOWER LIGHTING
There will be six (
6 ) Whelen®, Model M
6 *C, flashing LED warning lights with chrome trim
installed per the following:

Two (
2 ) lights,
one (
1 ) each side on the front custom cab corner
. The
side front lights to be red
.

Two (
2 ) lights,
one (
1 ) each side of cab rearward of crew cab doors
. The
side middle lights to be
red
.

Two (
2 ) lights,
one (
1 ) each side located between the tandems
. The
side rear lights to be red
.

The lights will include clear lenses.

There will be a switch in the cab on the switch panel to control the lights. 0745863
Lights, Side, Wln M9** LED, Trm Fet
2nd

SIDE WARNING LIGHTS
There will be
two (
2 )
Whelen®, Model M
9 **,

6.50 " high x

10.37 " wide x

1.37 " deep flashing LED
warning light(s) with
chrome trim
provided,
each side of the crew cab, behind the doors, as high
as possible
.

The
light(s) to include red LEDs
. The
warning light lens color(s) to be clear
.

These lights will be activated
with the side warning switch
.

White LEDs will be deactivated when the parking brake is applied.

Amber, blue, green or red LEDs may be load managed when the parking brake is applied. 51 959
Bid #:

Page 108 of 555 ends

0745867
Lights, Side, Wln M9** LED, Trm Fet
1st

SIDE WARNING LIGHTS
There will be
two (
2 )
Whelen®, Model M
9 **,

6.50 " high x

10.37 " wide x

1.37 " deep flashing LED
warning light(s) with
chrome trim
provided,
upper forward hatch compartment, each side
.

The
light(s) to include red LEDs
. The
warning light lens color(s) to be clear
.

These lights will be activated
with the side warning switch
.

White LEDs will be deactivated when the parking brake is applied.

Amber, blue, green or red LEDs may be load managed when the parking brake is applied. 0564655
Lights, Rear Zn Lwr, Wln M6*C LED,
Clear Lens, For Tail Lt Housing

REAR ZONE LOWER LIGHTING
There will be two (
2 ) Whelen®, Model M
6 *C, LED flashing warning lights located at the rear of the apparatus.

The
driver's side rear light to be red
The
passenger's side rear light to be red
Both lights will include a lens that is clear.

There will be a switch located in the cab on the switch panel to control the lights. 0541155
Lights, Rear/Side Up Zone, Wln
M9*C LED, Clear Lens 4lts

WARNING LIGHTS (Rear and Side upper zones)
Four (
4 ) Whelen, model M
9 *C LED flashing warning lights will be provided at the rear of the apparatus.

The
side rear upper light(s) on the driver's side to be red .

The
rear upper light(s) on the driver's side to be red
.

The
rear upper light(s) on the passenger's side to be red
.

The
side rear upper light(s) on the passenger's side to be red .

These lights will include a lens that is clear.

There will be a switch located in the cab on the switch panel to control the lights. 0006551
Not Required, Lights, Rear Upper
Zone Blocking
0791528
Light, Traffic Directing, Wln TAL65,

36.00" Long, TACTL5

TRAFFIC DIRECTING LIGHT
There will be one (
1 ) Whelen®, Model TAL
65 ,

36.00 " long x

2.87 " high x

2.25 " deep, amber LED
traffic directing light installed at the rear of the apparatus.

The Whelen, Model TACTL
5 , control head will be included with this installation.

The controller will be energized when the battery switch is on.

The
auxiliary flash to be activated when the emergency master switch is on .
0586458
Location, TDL, Surface Mounted with
Painted Box
This traffic directing light will be surface mounted with a smooth aluminum box, painted to match the surface that it is being mounted on, at the rear of the apparatus as high as practical. 0530282
Location, Traf Dir Lt Controller,
Overhead Switch Panel DS Right
End
The traffic directing light control head will be located in the driver side overhead switch panel in the right panel position.
0006646
Electrical System, 120/240VAC,
General Design
ELECTRICAL SYSTEM GENERAL DESIGN for ALTERNATING CURRENT The following guidelines will apply to the
120/240
VAC system installation:

General
Any fixed line voltage power source producing alternating current (ac) line voltage will produce electric power at
60 cycles plus or minus
3 cycles.

Except where superseded by the requirements of the current edition of applicable NFPA standards, all components, equipment and installation procedures will conform to NFPA 70 ,
National Electrical Code (herein referred to as the NEC).

Line voltage electrical system equipment and materials included on the apparatus will be listed and installed in accordance with the manufacturer's instructions. All products will be used only in the manner for which they have been listed.

Grounding
Grounding will be in accordance with Section
250-6
"Portable and Vehicle Mounted Generators"
of the NEC. Ungrounded systems will not be used. Only stranded or braided copper conductors will be used for grounding and bonding.

An equipment grounding means will be provided in accordance with Section 250-91
(Grounding
Conductor Material) of the NEC.

The grounded current carrying conductor (neutral) will be insulated from the equipment grounding conductors and from the equipment enclosures and other grounded parts. The neutral conductor will be colored white or gray in accordance with Section 200-6
(Means of Identifying Grounding
Conductors) of the NEC.

In addition to the bonding required for the low voltage return current, each body and driving or crew compartment enclosure will be bonded to the vehicle frame by a copper conductor. This conductor will have a minimum amperage rating of
115
percent of the nameplate current rating of
the power source specification label as defined in Section 310-15
(amp capacities) of the NEC. A
single conductor properly sized to meet the low voltage and line voltage requirements will be permitted to be used.

All power source system mechanical and electrical components will be sized to support the continuous duty nameplate rating of the power source.

Operation
Instructions that provide the operator with the essential power source operating instructions, including the power-up and power-down sequence, will be permanently attached to the apparatus at any point where such operations can take place.

Provisions will be made for quickly and easily placing the power source into operation. The control will be marked to indicate when it is correctly positioned for power source operation. Any 52 959
Bid #:

Page 109 of 555 ends

control device used in the drive train will be equipped with a means to prevent the unintentional movement of the control device from its set position.

A power source specification label will be permanently attached to the apparatus near the operator's control station. The label will provide the operator with the following information:

Rated voltage(s) and type (ac or dc)
Phase
Rated frequency
Rated amperage
Continuous rated watts
Power source engine speed
Direct drive (PTO) and portable generator installations will comply with Article 445
(Generators) of
the NEC.

Overcurrent protection
The conductors used in the power supply assembly between the output terminals of the power source and the main over current protection device will not exceed 144.00
" (
3658
mm) in length.

For fixed power supplies, all conductors in the power supply assembly will be type THHW, THW, or use stranded conductors enclosed in nonmetallic liquid tight flexible conduit rated for a minimum of
194
degree Fahrenheit (
90 degrees Celsius).

For portable power supplies, conductors located between the power source and the line side of the main overcurrent protection device will be type SO or type SEO with suffix WA flexible cord rated for
600
-volts at
194
degrees Fahrenheit (
90 degrees Celsius).

Wiring Methods
Fixed wiring systems will be limited to the following:

Metallic or nonmetallic liquid tight flexible conduit rated at not less than 194
degrees Fahrenheit
(
90 degrees Celsius)
or
Type SO or Type SEO cord with a WA suffix, rated at
600
volts at not less than
194
degrees
Fahrenheit (
90 degrees Celsius)
Electrical cord or conduit will not be attached to chassis suspension components, water or fuel lines, air or air brake lines, fire pump piping, hydraulic lines, exhaust system components, or low voltage wiring. In addition the wiring will be run as follows.

Separated by a minimum of

12.00 " (
305
mm), or properly shielded, from exhaust piping
Separated from fuel lines by a minimum of

6.00 " (
152
mm) distance
Electrical cord or conduit will be supported within

6.00 " (
152
mm) of any junction box and at a
minimum of every

24.00 " (
610
mm) of continuous run. Supports will be made of nonmetallic materials or corrosion protected metal. All supports will be of a design that does not cut or abrade the conduit or cable and will be mechanically fastened to the vehicle.

Wiring Identification
All line voltage conductors located in the main panel board will be individually and permanently identified. The identification will reference the wiring schematic or indicate the final termination point. When prewiring for future power sources or devices, the unterminated ends will be labeled showing function and wire size.

Wet Locations
All wet location receptacle outlets and inlet devices, including those on hardwired remote power distribution boxes, will be of the grounding type provided with a wet location cover and installed in accordance with Section
210-7
"Receptacles and Cord Connections" of the NEC.

All receptacles located in a wet location will be not less than

24.00 " (
610
mm) from the ground.

Receptacles on off-road vehicles will be a minimum of

30.00 " (
762
mm) from the ground.

The face of any wet location receptacle will be installed in a plane from vertical to not more than 45 degrees off vertical. No receptacle will be installed in a face up position.

Dry Locations
All receptacles located in a dry location will be of the grounding type. Receptacles will be not less than

30.00 " (
762
mm) above the interior floor height.

All receptacles will be marked with the type of line voltage ( 120
-volts or
240
-volts) and the current
rating in amps. If the receptacles are direct current, or other than single phase, they will be so marked.

Listing
All receptacles and electrical inlet devices will be listed to UL 498
, Standard for Safety
Attachment Plugs and Receptacles, or other appropriate performance standards. Receptacles used for direct current voltages will be rated for the appropriate service.

Electrical System Testing
The wiring and associated equipment will be tested by the apparatus manufacturer or the installer of the line voltage system.

The wiring and permanently connected devices and equipment will be subjected to a dielectric voltage withstand test of
900
-volts for one (
1 ) minute. The test will be conducted between live
parts and the neutral conductor, and between live parts and the vehicle frame with any switches in the circuit(s) closed. This test will be conducted after all body work has been completed.

Electrical polarity verification will be made of all permanently wired equipment and receptacles to determine that connections have been properly made.

Operational Test per Current Edition NFPA Standard
The apparatus manufacturer will perform the following operation test and ensure that the power source and any devices that are attached to the line voltage electrical system are properly connected and in working order. The test will be witnessed and the results certified by an independent third-party certification organization.

The prime mover will be started from a cold start condition and the line voltage electrical system loaded to
100
percent of the nameplate rating.

The power source will be operated at
100
percent of its nameplate voltage for a minimum of two
(
2 ) hours unless the system meets category certification as defined in the current edition of applicable NFPA standards.

Where the line voltage power is derived from the vehicle's low voltage system, the minimum continuous electrical load as defined in the current edition of applicable NFPA standards will be applied to the low voltage electrical system during the operational test. 53 959
Bid #:

Page 110 of 555 ends

0819272
Generator, Harrison, 25kW, 1 Phase,
PTO Shaft Drive (25KW Cont. Rating)
25 KW SINGLE PHASE, PTO GENERATOR
The generator will be a single phase, four (
4 )-wire
120/240
volts AC, Harrison Hydra-Gen,
25 KW
driven by a transmission "power takeoff" attached to the transmission.

Generator will have a built-in automatic voltage control.

Generator will be:

Continuous Duty Rating:
25,000
watts
Phase:

Single
Nominal Cycles:
60 hertz
Nominal Amp Rating:
104
at
240
-volts
Engine Speed at Engagement:

Idle
Engine Speed Engaged:
1100-1400
rpm range
Generator RPM:
1800
rpm
The output of the generator will be controlled by an electronic governor.

The main chassis transmission PTO will power the generator.

The generator will be operable in the stationary mode. There will be a shift control located inside the cab with an indicator light to note PTO engagement. The automatic high idle will be activated through interlocks only after the chassis parking brake is set, the truck transmission is in neutral and the generator PTO has been engaged.

To properly monitor the generator performance and load demands during operation, a digital generator meter display will be provided and a digital engine monitor will be mounted near the panel board.

The generator meter display will constantly monitor and display the following items:

Frequency
Amperage
Voltage
0016645
Location, PTO Generator, Between
the Frame Rails

GENERATOR LOCATION
The generator will be mounted under the body between the frame rails. 0009440
Starting Sw, Truck Engine Powered
Gen, Cab and Breaker Box

GENERATOR START
A switch will be located on the cab instrument panel and at the breaker panel area to engage the generator.
0016757
Not Required, Remote Start,
Generator
0016740
Not Required, Fuel System
0016767
Not Required, Oil Drain Extension,
Generator
0036738
Circuit Breaker Panel, Included With
PTO Generator

CIRCUIT BREAKER PANEL
The circuit breaker panel will be located
high on the right wall of compartment LS
2 .
0076607
Circuit Breaker Box, Subfeed Box

SUB FEED CIRCUIT BREAKER BOX
A Cutler Hammer sub feed box will be supplied with current limiting circuit breakers to protect the on board circuits when an auxiliary power source is used. The sub feed box will distribute power to specific circuits in the vehicle.

Location will be
near breaker box
.
0092381
Guard, Splash Guard for PTO
Generator Between the Frame Rails,
Stainless Steel

GENERATOR SPLASH GUARD
A stainless steel splash guard will be installed to reduce the amount of road spray on a frame mounted PTO generator.
0066606
Hourmeter, Generator

GENERATOR HOURMETER
An electric hourmeter will be provided

NEAR BREAKER BOX
.
0016771
Not Required, Routing Exhaust,
Generator
0783270
Circuit Breaker Panel, Sub Feed,
Cutler Hammer, Shoreline to Gen
Transfer Sw

SUB FEED CIRCUIT BREAKER PANEL
There will be a shoreline to generator transfer switch powered sub feed circuit breaker panel installed in the
LS
2 . A directory for each breaker will be provided adjacent to the circuit breaker panel. Identification of circuits will be done in a durable manner that provides years of service. 54 959
Bid #:

Page 111 of 555 ends

0759119
SP
Light Twr, W-B Chf Pr NS2.3-450
WHL, 3-P*H2 12VDC Lts Cld 7.5'

LIGHT TOWER
There will be one (
1 ) Will-Burt, Model NS

2.3-450
WHL light tower provided.

There will be three (
3 ) Whelen Model P*H
2 ,
18,520
lumens
12 volt DC light heads with
flood
optics
included on this tower.

The
painted parts of the light tower and the light heads to be black .

This tower will be connected to the Do Not Move Truck Indicator in the cab.

The lights included with this tower may be load managed when the parking brake is applied. 0629874
Location, Light Tower, Cab Roof,
Saber FR/Enforcer
Light Tower Location
The light tower will be installed on the cab roof.
0617750
Controller, Lt Twr, W-B, Wired
Hndhld, E-STOP Chf, Chf Pr, Pow Pr

Light Tower Controller
There will be one (
1 ) handheld wired controller included.
0664791
Location, Light Tower Controller,
Driver's Side Front Body
Compartment
Light Tower Controller Location
The light tower controller will be installed in the driver's side front body compartment. 0006826
Reel, Elect Cable, Hannay, ECR-
6600, (3) Wire

ELECTRIC CORD REEL
Furnished with the
120
volt AC electrical system will be a Hannay, series ECR- 6600
, cord reel
wired for a three (
3 ) conductor cord. The reel will be provided with a
12 -volt electric rewind switch,
that is guarded to prevent accidental operation and labeled for its intended use. The switch will be protected with a fuse and installed at a height not to exceed 72 inches above the operators
standing position.

The exterior finish of the reel(s) will be
painted
#269
gray from the reel manufacturer
.

A captive roller assembly to be provided to aid in the payout and loading of the reel . A ball stop
will be provided to prevent the cord from being wound on the reel.

A label will be provided in a readily visible location adjacent to the reel. The label will indicate current rating, current type, phase, voltage and total cable length.

A total of
two (
2 ) cord reels
will be provided
upper forward section of LS
4 AND RS
4 .
0006828
Cord, Electric, 10/3 Yellow, 3 Wire
CORD
Provided for electric distribution will be
two (
2 ) lengths, one (
1 ) for each reel,
of
200
feet
of yellow
10/3
electrical cord, weather resistant
105
degree Celsius to -
50 degree Celsius,
600
volt
jacketed SOOW cord.

No connector
will be installed on the end of the cord.
0838081
Box, Junc, Akron, 3-Wire, 20 Amp,
Configurable

PORTABLE JUNCTION BOX
There will be
two (
2 )
Akron EJBX gray,
20 Amp,
3 -Wire electrical junction box(es) provided.

Each box will be provided with the following:

There will be
NEMA L
5-20
,
20 amp,
120
volt twist lock junction box pigtail plug
.

The first position will have a
NEMA
5-20
,
20 amp,
120
volt straight blade GFCI protected Duplex
junction box receptacle
.

The second position will have a
NEMA
5-20
,
20 amp,
120
volt straight blade Duplex junction box
receptacle
.

The third position will have a
NEMA L
5-20
,
20 amp,
120
volt twist lock single junction box
receptacle
.

The fourth position will have a
NEMA L
5-20
,
20 amp,
120
volt twist lock single junction box
receptacle
.

Backlit face plates.

GFCI Function If Selected:

GFCI receptacles in the first position of the circuit protects the additional receptacles.

GFCI receptacles in the first and third positions of the box protects the second and fourth receptacles.

GFCI receptacles in the last position only protects that circuits receptacle.

GFCI receptacles in all four positions protects each circuits receptacle separately. 0006824
Holder, Junction Box, Tread Plate
Aluminum

JUNCTION BOX HOLDER
There will be an aluminum junction box holder installed adjacent to the cord reel. A total of two (
2 )
will be
mounted at pick-up
.
0779703
Receptacle Strip, 20A 120V 6-Place,
Sentrex M620BZLS, Surge
Protected, Int Body

POWER OUTLET STRIP
There will be
one (
1 )
Sentrex Model M
620
BZLS

18.00 " long x

2.00 " wide x

1.75 " thick, surge
protected receptacle strip(s) with six (
6 )
20 amp
120
volt AC straight blade receptacles provided

TO BE PROVIDED
.

The strip(s) selected will be powered from
onboard generator to second onboard generator
transfer switch.
through a receptacle located adjacent to the strip(s).

There will be a label installed near the strip(s) that state the following:

Line Voltage
Current Ratting (amps)
Phase
Frequency
55 959
Bid #:

Page 112 of 555 ends

0036622
Receptacle, 20A 120V 3-Pr 3-Wr SB
Dup, GFCI, Wtrprf
120

VOLT RECEPTACLE
There will be
two (
2 )
,
20 amp
120
volt AC three (
3 ) wire straight blade duplex GFCI receptacle(s)
with waterproof flip up cover(s) installed
lower rear body bulkhead, one each side
. The NEMA
configuration for the receptacles will be
5-20
R.

The receptacle(s) will be powered from the
on board generator
.

There will be a label installed near the receptacle(s) that state the following:

Line Voltage
Current Ratting (amps)
Phase
Frequency
0835289
SP
Compressor, Tool Air, Hydraulic
Drive, 140 cfm, Hercules

TOOL AIR COMPRESSOR,
140

CFM HYDRAULIC DRIVE
A Hercules hydraulic drive air compressor will be provided. The compressor will have a capacity of delivering
140
cfm of free air at
150
psig. The compressor will be located in a full width recess at the front of the body.

The hydraulic drive system will consist of a gear pump, a hydraulic reservoir with integral return line filter, a hydraulic control manifold and two (
2 )
12 V air cooler heat exchanger with
temperature switch.

The pump will be installed on the truck transmission PTO and will be operational anytime the hotshift PTO is engaged. The pump will be operable in the stationary mode with a PTO switch located inside the cab. There will be an indicator light to note PTO engagement.

The system will incorporate a single circuit hydraulic manifold that will route the fluid under pressure to the the compressor.

The control manifold will be located
TBD
.

The
12 V air coolers will be located in the best location as determined by engineering.

There will be
two (
2 ) low pressure regulated circuits
for the reel(s) located
TBD
.

Compressor
The compressor will be an oil flooded rotary screw compressor. Air compressor inlet control valve will be an integral design incorporated in the housing.

Hydraulic Motor
The compressor motor will be a gear type hydraulic motor.

Compressor Drive
Compressor hydraulic drive motor to be directly coupled to air compressor through a flexible coupling (no belt drives).

Weight
The compressor will be
650
lb dry weight.

Dimensions
The dimensions of the compressor assembly will be

31.00 " long x

18.50 " wide x

22.125
" high.

Air Intake Filters
Separate two (
2 )-stage, heavy duty, dry-type air filters will be provided to remove dirt particulate from entering the air compressor.

Air/Fluid Separator
The separator to be located internally in the air receiver tank. The separator will be constructed with a pleated media, welded straps, scrim barrier, support screen, expanded metal outer wrap and internal and external grounding. The separator will be provided for enhanced air quality, reduced operating and maintenance cost and optimized compressor performance.

Instrument Panel
The compressor instrument panel will include the compressor air pressure gauge, hour meter, compressor oil temperature gauge and an over-temperature/over-pressure reset switch.

Protective Circuit
The compressor will provide provisions for automatic shutdown in case of high compressor temperature or over pressurization. Additional protective features provided will include automatic blow down valve, receiver relief valve and minimum pressure valve.

Cooling System
The compressor cooling system will allow rated air delivery and pressure operation continuously between -
20 degree Fahrenheit and
120
degree Fahrenheit ambient temperatures. (No ABS
plastic shrouding) Compressor fluid will be filtered by a 25 micron full flow spin-on replaceable
filter canister. A fan temperature switch will be provided to regulate compressor cooling.

Inlet Controls
A pneumatic inlet control valve will be integrated into the compressor system and will automatically modulate output from
0 up to
100
percent in response to air demand.

Mainframe and Enclosure
Fully powder coated galvanneal mainframe and sheet metal enclosure with full service access.

General
The compressor will be manufactured in an ISO
9001
certified quality system.

Warranty
The compressor manufacturer's standard two (
2 ) year warranty will be provided with the
compressor.
0514853
Outlet, Tool Air from Tool
Compressor, 1.50" NST

AIR OUTLET
There will be
two (
2 )

1.50 " NST threaded air outlets provided to allow installation of the purchasers connection fittings. Each outlet will be individually valved and regulated off the system pressure regulator and located

CENTERED ABOVE THE SIDE HITCH RECEIVER BETWEEN

THE TANDEMS, ONE PER SIDE
.
0519934
Not Required, Brand, Hydraulic Tool
System
0649753
Not Required, PTO Driven Hydraulic
Tool System
56 959
Bid #:

Page 113 of 555 ends

0007150
Bag of Nuts and Bolts

LOOSE EQUIPMENT
The following equipment will be furnished with the completed unit:

One (
1 ) bag
of chrome, stainless steel, or cadmium plated screws, nuts, bolts and washers, as used in the construction of the unit.
0816517
NFPA Required Loose Equipment,
Special Services, NFPA/ULC
2024,Prov by Fire Dept

NFPA LOOSE EQUIPMENT
NFPA Required Loose Equipment Provided by Fire Department The following loose equipment as outlined in NFPA
1900
,
2024
edition, table

8.1 and CAN/ULC
S
515:2024
edition, section

5.2 will be provided by the fire department:

One (
1 ) traffic vest for each seating position, each vest to comply with ANSI/ISEA 107
,
American
National Standard for High-Visibility Safety Apparel and Accessories , and have a five-point
breakaway feature that includes two (
2 ) at the shoulders, two (
2 ) at the sides, and one (
1 ) at the
front.

Five (
5 ) fluorescent orange traffic cones not less than

28.00 " (
711
mm) in height, each equipped
with a

6.00 " (
152
mm) retro-reflective white band no more than

4.00 " (
152
mm) from the top of
the cone, and an additional

4.00 " (
102
mm) retro-reflective white band

2.00 " (
51 mm) below the

6.00 " (
152
mm) band.

Five (
5 ) illuminated warning devices such as highway flares, unless the five ( 5 ) fluorescent
orange traffic cones have illuminating capabilities.

Four (
4 ) ladder belts meeting the requirements of NFPA
2500
.

NFPA Loose Equipment That Should be Considered
The following loose equipment as outlined in NFPA
1900
,
2024
edition, appendix table A.

8.4 (a)
and CAN/ULC S
515:2024
edition, section

5.2 should be considered:

Two (
2 ) SCBA apparatus
Two (
2 ) SCBA spare cylinders
One (
1 ) first aid kit
One (
1 ) automatic external defibrillator (AED)
0796255
Not Required, Soft Suction, Rescue
No Pump
0816939
Extinguisher, Dry Chemical, NFPA
2024, Provided by Fire Department

DRY CHEMICAL EXTINGUISHER PROVIDED BY FIRE DEPARTMENT
The extinguisher is not on the apparatus as manufactured. The fire department will provide and mount the extinguisher.
0816937
Extinguisher, 2.5 Gal. Pressurized
Water, NFPA/ULC 2024, Provided by
Fire Dept

WATER EXTINGUISHER PROVIDED BY FIRE DEPARTMENT
The extinguisher is not on the apparatus as manufactured. The fire department will provide and mount the extinguisher.
57 959
Bid #:

Page 114 of 555 ends

0741569
Paint Process / Environmental
Requirements, Appleton

PAINT PROCESS
The exterior custom cab and body painting procedure will consist of a seven ( 7 ) step finishing
process as follows:

Manual Surface Preparation
- All exposed metal surfaces on the custom cab and body will be thoroughly cleaned and prepared for painting. Imperfections on the exterior surfaces will be removed and sanded to a smooth finish. Exterior seams will be sealed before painting. Exterior surfaces that will not be painted include; chrome plating, polished stainless steel, anodized aluminum and bright aluminum treadplate.

Chemical Cleaning and Pretreatment
- All surfaces will be chemically cleaned to remove dirt, oil, grease, and metal oxides to ensure the subsequent coatings bond well. The aluminum surfaces will be properly cleaned and treated using a high pressure, high temperature 4 step Acid Etch
process. The steel and stainless surfaces will be properly cleaned and treated using a high temperature
3 step process specifically designed for steel or stainless. The chemical treatment converts the metal surface to a passive condition to help prevent corrosion.

Surfacer Primer
- The Surfacer Primer will be applied to a chemically treated metal surface to provide a strong corrosion protective basecoat. A minimum thickness of 2 mils of Surfacer Primer
is applied to surfaces that require a Critical aesthetic finish. The Surfacer Primer is a two- component high solids urethane that has excellent sanding properties and an extra smooth finish when sanded.

Finish Sanding
- The Surfacer Primer will be sanded with a fine grit abrasive to achieve an ultra- smooth finish. This sanding process is critical to produce the smooth mirror like finish in the topcoat.

Sealer Primer
- The Sealer Primer is applied prior to the Basecoat in all areas that have not been previously primed with the Surfacer Primer. The Sealer Primer is a two-component high solids urethane that goes on smooth and provides excellent gloss hold out when topcoated.

Base
coat Paint
- Two coats of a high performance, two component high solids polyurethane basecoat will be applied. The Basecoat will be applied to a thickness that will achieve the proper color match. The Basecoat will be used in conjunction with a urethane clear coat to provide protection from the environment.

Clear Coat
- Two (
2 ) coats of Clear Coat will be applied over the Basecoat color. The Clear Coat is a two-component high solids urethane that provides superior gloss and durability to the exterior surfaces. Lap style and roll-up doors will be Clear Coated to match the body. Paint warranty for the roll-up doors will be provided by the roll-up door manufacturer.

After the cab and body are painted, the color will be verified to make sure that it matches the color standard. Electronic color measuring equipment will be used to compare the color sample to the color standard entered into the computer. Color specifications will be used to determine the color match. A Delta E reading will be used to determine a good color match within each family color.

All removable items such as brackets, compartment doors, door hinges, and trim will be removed and painted separately if required, to ensure paint behind all mounted items. Body assemblies that cannot be finish painted after assembly will be finish painted before assembly.

The paint finish quality levels for critical areas of the apparatus (cab front and sides, body sides and doors, and boom lettering panels) are to meet or exceed Cadillac/General Motors GMW
15777
global paint requirements. Orange peel levels are to meet or exceed the #6
A.C.T.
standard in critical areas. The manufacture's written paint standards will be available upon request.

Environmental Impact
Contractor will meet or exceed all current state regulations concerning paint operations. Pollution control will include measures to protect the atmosphere, water and soil. Controls will include the following conditions:

Topcoats and primers will be chrome and lead free.

Metal treatment chemicals will be chrome free. The wastewater generated in the metal treatment process will be treated on-site to remove any other heavy metals.

Particulate emission collection from sanding operations will have a

99.99 percent efficiency
factor.

Particulate emissions from painting operations will be collected by a dry filter or water wash process. If the dry filter is used, it will have an efficiency rating of 98 percent. Water wash
systems will be

99.97 percent efficient.

Water from water wash booths will be reused. Solids will be removed on a continual basis to keep the water clean.

Paint wastes are disposed of in an environmentally safe manner.

Empty metal paint containers will be recycled to recover the metal.

Solvents used in clean-up operations will be recycled on-site or sent off-site for distillation and returned for reuse.

Additionally, the finished apparatus will not be manufactured with or contain products that have ozone depleting substances. Contractor will, upon demand, present evidence that the manufacturing facility meets the above conditions and that it is in compliance with his state EPA rules and regulations.
0709846
Paint, Two-Tone Color,
Velocity/Impel

CAB TWO-TONE PAINT
The cab will be painted two-tone, with the upper section painted #580
tuxedo black metallic
and
the lower section painted
#263
Red
. There will be
a standard two-tone cab paint break provided
.

There will be
a special cab shield designed and shown on the lettering and striping print .
0709833
Paint, Two-Tone Color, Body

TWO-TONE BODY PAINT
The body will be painted two-tone with the upper section painted metallic to match the upper
section of the cab
and the lower section
painted to match the lower section of the cab
. The body
paint break will be
at the seam between the body and hatch compartment or catwalk on each side
.
58 959
Bid #:

Page 115 of 555 ends

0646901
Paint Chassis Frame Assy, With
Liner, E-Coat, Standard

PAINT CHASSIS FRAME ASSEMBLY
The chassis frame assembly will be finished with
a single system black top coat
before the
installation of the cab and body, and before installation of the engine and transmission assembly, air brake lines, electrical wire harnesses, etc.

Components that are included with the chassis frame assembly that will be painted (unless otherwise stated in a secondary option) are:

Frame rails
Frame liners
Cross members
Axles
Suspensions
Steering gear
Battery boxes
Bumper extension weldment
Frame extensions
Body mounting angles
Rear Body support substructure (front and rear)
Pump house substructure
Steel fuel tank
Castings
Individual piece parts used in chassis and body assembly Components treated with epoxy E-coat protection prior to paint:

Two (
2 ) C-channel frame rails
Two (
2 ) frame liners
The E-coat process will meet the technical properties shown. 0693797
No Paint Required, Aluminum Front
Wheels

0693792
No Paint Required, Aluminum Rear
Wheels

0733739
Paint, Axle Hubs

AXLE HUB PAINT
All axle hubs will be painted
black
#101
.
0620095
Paint, Drip Rail, Cab

PAINTED RAIN DRIP
The cab roof rain drip will be painted to match the cab roof paint color. 0007230
Compartment, Painted, Spatter Gray

COMPARTMENT INTERIOR PAINT
The interior of all compartments will be painted with a gray spatter finish for ease of cleaning and to make it easier to touch up scratches and nicks.
0544129
Reflective Band, 1"-6"-1"

REFLECTIVE STRIPES
Three (
3 ) reflective stripes will be provided across the front of the vehicle and along the sides of the body. The reflective band will consist of a

1.00 "
black
stripe at the top with a

1.00 " gap then a

6.00 "
black
stripe with a

1.00 " gap and a

1.00 "
black
stripe on the bottom.
0510041
Reflective across Cab Face, Imp/Vel

The reflective band provided on the cab face will be below the headlights on the fiberglass. 0536955
Stripe, Chevron, Rear, Diamond
Grade, Rescue

REAR CHEVRON STRIPING
There will be alternating chevron striping located on the rear-facing vertical surface of the apparatus. Covered surfaces will include the exterior rear wall. Rear compartment doors, entry doors, or walkway areas will not be covered.

The colors will be red and
fluorescent yellow green
diamond grade.

Each stripe will be

6.00 " in width.

This will meet the requirements of the current edition of NFPA 1901
, which states that
50%
of the
rear surface will be covered with chevron striping.
0760572
SP
Folded Ribbon in Reflective Stripe,
Pair, w/o Air Brushing

FOLDED RIBBON IN REFLECTIVE STRIPE
There will be
one (
1 )
pair(s) of a folded type ribbon(s), without air brushing, added to the reflective stripe located
Located on the D
3 & P
3 roll-up doors.
.
0670035
Stripe, Diamond Grade Chevron,
Toolboard

TOOLBOARD DIAMOND GRADE CHEVRON STRIPING
A series of alternating red diamond grade and
fluorescent yellow green diamond grade
reflective
stripes will be applied to the
one (
1 )
toolboard(s) located
RS
2 .
0545179
Stripe, Diamond Grade, Chevron,
Front Bumper

CHEVRON STRIPING ON THE FRONT BUMPER
There will be alternating chevron striping located on the front bumper.

The colors will be
Fluorescent Yellow-Green
983-23
and
Red
983-72
diamond grade.

The size of the striping will be

6.00 "
.
59 959
Bid #:

Page 116 of 555 ends

0065687
Stripe, Reflective, Cab Doors Interior

CAB DOOR REFLECTIVE STRIPE
A

6.00 " x

16.00 "
white
reflective stripe will be provided across the interior of each cab door. The stripe will be located approximately

1.00 " up from the bottom, on the door panel.

This stripe will meet the current edition of applicable NFPA standards. 0544003
Stripe, Reflective, HDR Walk-In
Rear/Side Door

REFLECTIVE STRIPE, HDR BODY DOOR(S)
A

6.00 " x

16.00 "
black
reflective stripe will be provided across the interior of each body entry door. The stripe will be located approximately

1.00 " up from the bottom, on the door panel.

The stripe will be provided on
one (
1 )
entry door.

This stripe will meet the NFPA
1901
requirement.
0680371
Stripe, Gold Leaf, Two-Tone Paint
Break with Shield, IPO Chrome
Molding

CAB STRIPE
There will be a genuine gold leaf stripe provided on both sides of the cab in place of the chrome molding and on the cab face with shield.
0027372
Lettering Specifications, (GOLD
STAR Process)

LETTERING
The lettering will be totally encapsulated between two ( 2 ) layers of clear vinyl.
0686440
Lettering, Gold Leaf, 3.00", (1-20)

LETTERING
One (
1 ) to twenty (
20 ) genuine gold leaf lettering,

3.00 " high, with
outline and shade
will be
provided.
0685562
Lettering, Printed Effect Gold Leaf,

5.00", Each

LETTERING
There will be printed effect gold leaf lettering,

5.00 " high, with
outline and shade
provided. There
will be
12 letters
provided.
0685978
Lettering, Reflective, 18.00", Each

LETTERING
There will be reflective lettering,

18.00 " high, with
no outline or shade
provided. There will be
six
(
6 ) letters
provided.
0686013
Lettering, Reflective, 6.00", Each

LETTERING
There will be reflective lettering,

6.00 " high, with
outline and shade
provided. There will be
four
(
4 ) letters
provided.
0686033
Lettering, Reflective, 4.00", Each

LETTERING
There will be reflective lettering,

4.00 " high, with
outline and shade
provided. There will be
nine
(
9 ) letters
provided.
0686084
Lettering, Reflective, 3.00", Each

LETTERING
There will be reflective lettering,

3.00 " high, with
outline
provided. There will be
three (
3 )
letters
provided.
0686236
Lettering, Gold Leaf, 5.00", Each

LETTERING
There will be genuine gold leaf lettering,

5.00 " high, with
outline and shade
provided. There will
be
six (
6 ) letters
provided.
0686256
Lettering, Gold Leaf, 4.00", Each

LETTERING
There will be genuine gold leaf lettering,

4.00 " high, with
outline and shade
provided. There will
be
nine (
9 ) letters
provided.
0017273
Emblem, Maltese Cross, Gold Leaf,
12"-14", Pair

MALTESE CROSS INSTALLATION
There will be
one (
1 )
pair of Maltese crosses, comprised of genuine gold leaf material, provided and installed
each front cab door per the LSP
.
0666388
Emblem, Freedom Flag with Twin
Towers, Each
EMBLEM
There will be
two (
2 )
emblem(s), approximately

15.00 " -

17.00 " wide
in size, installed
Located on
the upper portion of the EMS compartment door on cab sides. . The emblem will feature a "Flying
American Flag" and an "Eagle Head", along with buildings in the background. 0766493
Emblem, American Flag Muted
w/Thin Red Line, Ptd Cab Grille, All
Custom Chassis

CAB GRILLE DESIGN
A muted American flag with a thin red line design will be painted on the cab grille. 60 959
Bid #:

Page 117 of 555 ends

0772003
Manual, Fire Apparatus Parts, USB
Flash Drive, Custom

FIRE APPARATUS PARTS MANUAL
There will be
one (
1 )
custom parts manual(s) in USB flash drive format for the complete fire apparatus provided.

The manual(s) will contain the following:

Job number
Part numbers with full descriptions
Table of contents
Parts section sorted in functional groups reflecting a major system, component, or assembly Parts section sorted in alphabetical order
Instructions on how to locate parts
Each manual will be specifically written for the chassis and body model being purchased. It will not be a generic manual for a multitude of different chassis and bodies.

Service Parts Internet Site
The service parts information included in these manuals are also available on the Pierce website.

The website offers additional functions and features not contained in this manual, such as digital photographs and line drawings of select items. The website also features electronic search tools to assist in locating parts quickly.
0772037
Manual, Chassis Service, USB Flash
Drive, Custom

CHASSIS SERVICE MANUALS
There will be
one (
1 )
chassis service manuals on USB flash drives containing parts and service information on major components provided with the completed unit.

The manual will contain the following sections:

Job number
Table of contents
Troubleshooting
Front Axle/Suspension
Brakes
Engine
Tires
Wheels
Cab
Electrical, DC
Air Systems
Plumbing
Appendix
The manual will be specifically written for the chassis model being purchased. It will not be a generic manual for a multitude of different chassis and bodies. 0773381
Manual, Chassis Operation, (1) USB
Flash Drive, Custom, English

CHASSIS OPERATION MANUAL
The chassis operation manual will be provided on one (
1 ) USB flash drive. The manual will be in
the English language.
0030008
Warranty, Basic, 1 Year, Apparatus,
WA0008
ONE (
1 ) YEAR MATERIAL AND WORKMANSHIP
A Pierce basic apparatus limited warranty certificate, WA 0008
, is included with this proposal.
0611136
Warranty, Chassis, 3 Year,
Velocity/Impel, WA0284

THREE (
3 ) YEAR MATERIAL AND WORKMANSHIP
The Pierce custom chassis limited warranty certificate, WA 0284
, is included with this proposal.
0696698
Warranty, Engine, Cummins, 5 Year,
WA0181

ENGINE WARRANTY
A Cummins
five (
5 ) year
limited engine warranty will be provided. A limited warranty certificate, WA
0181
, is included with this proposal.
0684953
Warranty, Steering Gear, Sheppard
M110, 3 Year WA0201

STEERING GEAR WARRANTY
A Sheppard
three (
3 ) year
limited steering gear warranty will be provided. A copy of the warranty certificate will be submitted with this proposal.
0595767
Warranty, Frame, 50 Year,
Velocity/Impel, WA0038

FIFTY (
50 ) YEAR STRUCTURAL INTEGRITY
The Pierce custom chassis frame and crossmembers limited warranty certificate, WA 0038
, is
included with this proposal.
0595698
Warranty, Axle, 3 Year, TAK-4,
WA0050

FRONT AXLE THREE (
3 ) YEAR MATERIAL AND WORKMANSHIP WARRANTY
The Pierce TAK-
4 suspension limited warranty certificate, WA
0050
, is included with this proposal.
0644874
Warranty, Axle, 3 Year, TAK-4, IRS,
WA0249

REAR AXLE THREE (
3 ) YEAR MATERIAL AND WORKMANSHIP WARRANTY
Pierce TAK-
4 ® independent rear suspension will be provided with a three ( 3 ) year material and
workmanship limited warranty. The manufacturer's warranty will provide that the independent rear suspension be free from any defect related to material and workmanship on the portion of the apparatus built by the manufacturer that would arise under normal use and service. 61 959
Bid #:

Page 118 of 555 ends

0652758
Warranty, ABS Brake System, 3
Year, Meritor Wabco, WA0232

ABS BRAKE SYSTEM THREE (
3 ) YEAR MATERIAL AND WORKMANSHIP

WARRANTY
A Meritor Wabco
™
ABS brake system limited warranty certificate, WA
0232
, is included with this
proposal.
0019914
Warranty, Structure, 10 Year, Custom
Cab, WA0012
TEN (
10 ) YEAR STRUCTURAL INTEGRITY
The Pierce custom cab limited warranty certificate, WA
0012
, is included with this proposal.
0744240
Warranty, Paint, 10 Year, Cab, Pro-
Rate, WA0055
TEN (
10 ) YEAR PRO-RATED PAINT AND CORROSION
A Pierce cab limited pro-rated paint warranty certificate, WA 0055
, is included with this proposal.
0524627
Warranty, Electronics, 5 Year, MUX,
WA0014
FIVE (
5 ) YEAR MATERIAL AND WORKMANSHIP
The Pierce Command Zone electronics limited warranty certificate, WA 0014
, is included with this
proposal.
0695416
Warranty, Pierce Camera System,
WA0188

CAMERA SYSTEM WARRANTY
A Pierce fifty four (
54 ) month
warranty will be provided for the camera system
.
0647720
Warranty, Pierce LED Strip Lights,
WA0203

COMPARTMENT LIGHT WARRANTY
The Pierce
12 volt DC LED strip lights limited warranty certificate, WA 0203
, is included with this
proposal.
0046369
Warranty, 5-year EVS Transmission,
Standard Custom, WA0187

TRANSMISSION WARRANTY
The transmission will have a
five (
5 ) year/unlimited mileage
warranty covering
100
percent
parts and labor. The warranty will be provided by Allison Transmission.

Note: The transmission cooler is not covered under any extended warranty you may be getting on your Allison Transmission. Please review your Allison Transmission warranty for coverage limitations.
0685945
Warranty, Transmission Cooler,
WA0216

TRANSMISSION COOLER WARRANTY
The transmission cooler will carry a five (
5 ) year parts and labor warranty (exclusive to the
transmission cooler). In addition, a collateral damage warranty will also be in effect for the first three (
3 ) years of the warranty coverage and will not exceed
$10,000
per occurrence. A copy of
the warranty certificate will be included with this proposal. 0033401
Not Required, Tank Warranty

0596024
Warranty, Structure, 15 Year, HDR,
WA0010

FIFTEEN (
15 ) YEAR STRUCTURAL INTEGRITY
The Pierce heavy duty rescue apparatus body limited warranty certificate, WA 0010
, is included
with this proposal.
0693126
Warranty, AMDOR, Roll-up Door, 10
Year/5 Year Painted, WA0185

ROLL UP DOOR MATERIAL AND WORKMANSHIP WARRANTY
An AMDOR roll-up door limited warranty will be provided. The roll-up door will be warranted against manufacturing defects for a period of
ten (
10 ) years
. A
five (
5 ) year
limited warranty will
be provided on painted roll up doors.

The limited warranty certificate, WA
0185
, is included with this proposal.
0012599
Warranty, Pump, Not Required

0046370
Not Required, Warranty, No
Plumbing
0641372
Warranty, Foam System, Not
Available
0595820
Warranty, Paint, 10 Year, Body, Pro-
Rate, WA0057
TEN (
10 ) YEAR PRO-RATED PAINT AND CORROSION
A Pierce body limited pro-rated paint warranty certificate, WA 0057
, is included with this proposal.
0595421
Warranty, Goldstar, 3 Year,
Apparatus, WA0018

THREE (
3 ) YEAR MATERIAL AND WORKMANSHIP
The Pierce Goldstar gold leaf lamination limited warranty limited warranty certificate, WA 0018
, is
included with this proposal.
62 959
Bid #:

Page 119 of 555 ends

0819254
Certification, Vehicle Stability,
CD0196

VEHICLE STABILITY CERTIFICATION
The fire apparatus manufacturer will provide a certification stating the apparatus complies with NFPA
1900
, current edition, section

7.14 , Vehicle Stability. The certification is included with this proposal.
0808577
Certification, Engine Installation,
Velocity, Cummins X15, 2027

ENGINE INSTALLATION CERTIFICATION
The fire apparatus manufacturer will provide a certification, along with a letter from the engine manufacturer stating they approve of the engine installation in the bidder's chassis. The certification will be provided at the time of delivery. 0686786
Certification, Power Steering,
CD0098

POWER STEERING CERTIFICATION
The fire apparatus manufacturer will provide a certification stating the power steering system as installed meets the requirements of the component supplier. The certification is included with this proposal.
0544033
Certification, Cab Integrity, Velocity 2-
Door, CD0009

CAB INTEGRITY CERTIFICATION
The fire apparatus manufacturer will provide a cab crash test certification with this proposal. The certification states that the cab must meet or exceed the requirements below:
- European Occupant Protection Standard ECE Regulation No. 29 .
- SAE J
2422
Cab Roof Strength Evaluation - Quasi-Static Loading Heavy Trucks. - SAE J
2420
COE Frontal Strength Evaluation - Dynamic Loading Heavy Trucks. - Roof Crush
The cab will be subjected to a roof crush force of
22,500
lb. This value meets the ECE
29 criteria
and is equivalent to the front axle rating up to a maximum of ten ( 10 ) metric tons.
- Side Impact
The same cab will be subjected to dynamic preload where a 13,275
-lb moving barrier slams into
the side of the cab at

5.50 mph at a force of
13,000
ft-lb. This test is part of the SAE J
2422
test
procedure and more closely represents the forces a cab will see in a rollover incident. - Frontal Impact
The same cab will withstand a frontal impact of
32,600
ft-lb of force using a moving barrier in
accordance with SAE J
2420
.

The same cab will withstand all tests without any measurable intrusion into the survival space of the occupant area.
0548950
Certification, Cab Door Durability,
Velocity/Impel, CD0001

CAB DOOR DURABILITY CERTIFICATION
Robust cab doors help protect occupants. Cab doors will survive a 200,000
-cycle door slam test
where the slamming force exceeds
20 G's of deceleration. The bidder will certify that the sample doors similar to those provided on the apparatus have been tested and have met these criteria without structural damage, latch malfunction, or significant component wear. 0548967
Certification, Windshield Wiper
Durability, Impel/Velocity, CD0005

WINDSHIELD WIPER DURABILITY CERTIFICATION
Visibility during inclement weather is essential to safe apparatus performance. Windshield wipers will survive a
3 million cycle durability test in accordance with section

6.2 of SAE J
198

Windshield
Wiper Systems - Trucks, Buses and Multipurpose Vehicles.

The bidder will certify that the wiper
system design has been tested and that the wiper system has met these criteria. 0667411
Certification, Electric Window
Durability, Velocity/Impel FR,
CD0004

ELECTRIC WINDOW DURABILITY CERTIFICATION
Cab window roll-up systems can cause maintenance problems if not designed for long service life. The window regulator design will complete
30,000
complete up-down cycles and still function
normally when finished. The bidder will certify that sample doors and windows similar to those provided on the apparatus have been tested and have met these criteria without malfunction or significant component wear.
0549273
Certification, Seat Belt Anchors and
Mounting, Imp/Vel/Vel SLT, CD0018

SEAT BELT ANCHOR STRENGTH
Seat belt attachment strength is regulated by Federal Motor Vehicle Safety Standards and should be validated through testing. Each seat belt anchor design will withstand 3000
lb of pull on both
the lap and shoulder belt in accordance with FMVSS
571.210
Seat Belt Assembly Anchorages.

The bidder will certify that each anchor design was pull tested to the required force and met the appropriate criteria.

SEAT MOUNTING STRENGTH
Seat attachment strength is regulated by Federal Motor Vehicle Safety Standards and should be validated through testing. Each seat mounting design will be tested to withstand 20 G's of force in
accordance with FMVSS
571.207
Seating Systems. The bidder will certify that each seat mount and cab structure design was pull tested to the required force and met the appropriate criteria. 63 959
Bid #:

Page 120 of 555 ends

0735950
Certification, Cab HVAC System Perf,
Vel/Imp FR,
CD0166/CD0168/CD0176/CD0177

PERFORMANCE CERTIFICATIONS
Cab Air Conditioning
Good cab air conditioning temperature and air flow performance keeps occupants comfortable, reduces humidity, and provides a climate for recuperation while at the scene. The cab air conditioning system will cool the cab from a heat-soaked condition at 100
degrees Fahrenheit to
an average of
78 degrees Fahrenheit in
30 minutes. The bidder will certify that a substantially similar cab has been tested and has met these criteria.

Cab Defroster
Visibility during inclement weather is essential to safe apparatus performance. The defroster system will clear the required windshield zones in accordance with SAE J 381
Windshield
Defrosting Systems Test Procedure And Performance Requirements - Trucks, Buses, And Multipurpose Vehicles.

The bidder will certify that the defrost system design has been tested in a cold chamber and passes the SAE J
381
criteria.

Cab Auxiliary Heater
Good cab heat performance and regulation provides a more effective working environment for personnel, whether in-transit, or at a scene. An auxiliary cab heater will warm the cab 77 degrees
Fahrenheit from a cold-soak, within
30 minutes when tested using the coolant supply methods found in SAE J
381
. The bidder will certify, at time of delivery, that a substantially similar cab has been tested and has met these criteria.
0545073
Amp Draw Report, NFPA Current
Edition

AMP DRAW REPORT
The bidder will provide, at the time of bid and delivery, an itemized print out of the expected amp draw of the entire vehicle's electrical system.

The manufacturer of the apparatus will provide the following:

Documentation of the electrical system performance tests.

A written load analysis, which will include the following:

The nameplate rating of the alternator.

The alternator rating under the conditions specified per:

Current edition of applicable NFPA standards.

The minimum continuous load of each component that is specified per:

Current edition of applicable NFPA standards.

Additional loads that, when added to the minimum continuous load, determine the total connected load.

Each individual intermittent load.

All of the above listed items will be provided by the bidder per the current edition of applicable NFPA standards.
0002758
Amp Draw, NFPA/ULC Radio
Allowance
0799248
Appleton/Florida BTO

0000031

HDR BODY

0000012

PIERCE CHASSIS
0004713

ENGINE, OTHER
0046396
EVS 4000 Series TRANSMISSION
0020037

NO PUMP

0020013

NO WATER TANK

0028047

NO FOAM SYSTEM

0046282
Not Required, Control Panel, No
Pump
0020007

AKRON VALVES

0020015

ABS SYSTEM

0752883
HDR

64 959
Bid #:

Page 121 of 555 ends

Electrical Analysis
1/2/2026
Bid #:
959
Milpitas Fire Walk-In HDR
Sales Rep:

Organization:

Myers, Rich
Golden State Fire Apparatus, Inc
Desc:

Job #:

Customer:

Milpitas Fire Dept.

Option:

Pierce Command Zone, Advanced Electronics & Control
System, Vel WiFi CZT
Type:

Multiplexed
Option
Description
Type*
Minimum
Load
Intermittent
Load
Total
Connected
0001244
High Idle w/Electronic Engine, Custom

0.00 1.20

0.00 0006826
Reel, Elect Cable, Hannay, ECR-6600, (3) Wire

0.00 72.00

0.00 0032189
Mirrors, Ramco, 8000PCHR, Heated/Remote, w/Heated/Remote Convex, Door Mount

0.00 0.00

8.00 0079166
Batteries, (4) Stryten/Exide Grp 31, 950 CCA ea, Threaded Stud

0.00 3.00

0.00 0122466
Cab Lift, Elec/Hyd, w/Manual Override, Imp/Vel

0.00 180.00

0.00 0532024
Tow Eyes, (2) w/Winch Receiver Rr/Sides, Under Body,
(Tanker/Rescue)

0.00 45.00

0.00 0554033
Switch, Ceiling Lights, HDR Walk-In

0.00 0.00

0.08 0583938
Lights, Engine Compt, Custom, Auto Sw, Wln 3SC0CDCR, 3" LED, Trim

0.00 0.60

0.00 0589905
Alarm, Back-up Warning, PRECO 1040

0.00 0.50

0.00 0606056
Lights, Hatch Compt, Not Required, HDR

0.00 0.00

0.00 0614669
Light, Map, Overhead, Round, Add, Sunnex SL9-200B25L LED Clr Lens, Ceiling Mount

0.00 0.74

0.00 0629270
Winch, Warn, Zeon 10-S Kit, 10,000 lb. Portable, Wireless, Syn,Polished Fairlead

0.00 460.00

0.00 0646930
Lights, (2), Illuminate Cab Floor, Wln Red OS Series, LED, Under Dash, Sep Sw

0.00 0.00

2.10 0653350
Guards, Vehicle Camera(s), Painted Smooth Aluminum

0.00 0.00

0.00 0653519
Camera, Pierce, LS Mux, RS, LS, R, Cameras, SD

0.00 1.20

0.00 0667108
Winch, Warn, 15000 lb. Fixed, Front, Synthetic Rope, Polished Fairlead

0.00 500.00

0.00 0667902
Controls, Electric Windows, All Cab Doors, Impel/Velocity FR

0.00 26.00

0.00 0687994
Engine Brake, Jacobs Compression Brake, Cummins Engine

0.00 0.42

0.00 0697077
Intercom, Atkinson Two-way, Cab to Body

0.00 0.01

0.00 0731649
HVAC, Heavy-Duty, Two Door Impel/Velocity FR, w/o Heat, CARE

0.00 0.00

92.00 0738110
Lights, Rear Scene, Wln, PCPSM1* Pioneer LED Fld/Spt, Surface Mount

0.00 0.00

12.00 0744629
Lights, Wln, PSL1** Pioneer, 12 VDC, 2nd

0.00 0.00

3.00 0744631
Lights, Wln, PSL1** Pioneer, 12 VDC, 1st

0.00 0.00

3.00 0745863
Lights, Side, Wln M9** LED, Trm Fet 2nd

0.00 3.60

2.40 0745867
Lights, Side, Wln M9** LED, Trm Fet 1st

0.00 3.60

2.40 0759119
Light Twr, W-B Chf Pr NS2.3-450 WHL, 3-P*H2 12VDC Lts Cld

7.5'

0.00 6.48

34.52 0774579
Lights, Wln, P*H2* Pioneer, 12 VDC, 1st

0.00 0.00

26.00 0795742
Not Required, Walking Surface, Alt. Walking Surface Lights, HDR

0.00 0.00

0.00 0806466
Lights, Backup, Wln M62BU, LED, For Tail Lt Housing

0.00 3.20

0.00 0819034
Light, Do Not Move Apparatus, Wln VTX609B, With Buzzer, Non- NFPA 2024

0.00 2.80

0.00 0819994
Radio, Jensen, AM/FM/WB, Bluetooth

0.00 0.00

2.00 0821263
Wiring, Spare, 20 A 12V DC, 12 Ckt FB, Blue Sea 5026 Batt Dir 1st NFPA1900/ULC

0.00 0.00

20.00 0821326
Wiring, Spare, 10 A 12V DC 2nd NFPA1900/ULC

0.00 0.00

10.00 0821337
ABS Wabco Brake System, Tandem Rear Axle, Tak-4, NFPA
1900/ULC

0.00 6.00

0.00 0821580
Wiring, Spare, 7.5A 12V DC 1st NFPA1900/ULC

0.00 0.00

7.50 0834418
USB, Cab, 2, 12V DC, Dual USB Termination, NFPA1900/ULC

0.00 0.00

5.00 0895310
Siren, Federal Q2B

0.00 100.00

0.00 0636439
Wiring, Spare, 37.5 A 12V DC, Cust Install Radio, 30A Bat Dir,

7.5A Ign & Grnd
Load Managed

0.00 0.00

75.00 0774333
Lights, Wln, P*H2* Pioneer, 12 VDC, 2nd
Load Managed

0.00 0.00

13.00 0783158
Light, Visor, HiViz, FT-B-72-*-*, Cnt Feature
Load Managed

0.00 0.00

23.84 0821192
Wiring, Spare, 20 A 12V DC 1st NFPA1900/ULC
Load Managed

0.00 0.00

20.00 0002758
Amp Draw, NFPA/ULC Radio Allowance
NFPA

5.00 0.00

0.00 0026105
Left Rear Compt, 60" Roll, WI
NFPA

0.90 1.80

0.90 0026109
Right Rear Compartment, 60" Roll, WI
NFPA

0.90 1.80

0.90 0026154
Entrance, Rear, 78" Interior Height, WI
NFPA

3.60 7.20

3.60 0092582
Load Manager/Sequencer, MUX
NFPA

0.56 0.56

0.00 0515810
Left Over Wheel Compt, 51.50"-51.50", Roll Door, Tandem, WI NFPA

0.90 1.80

0.90 * UDMC = User Defined Mission Critical, LM = User Defined Load Managed, S = Electrical Amperage Supply 1

Page 122 of 555 ends

Electrical Analysis
1/2/2026
Bid #:
959
Milpitas Fire Walk-In HDR
Sales Rep:

Organization:

Myers, Rich
Golden State Fire Apparatus, Inc
Desc:

Job #:

Customer:

Milpitas Fire Dept.

Option:

Pierce Command Zone, Advanced Electronics & Control
System, Vel WiFi CZT
Type:

Multiplexed
Option
Description
Type*
Minimum
Load
Intermittent
Load
Total
Connected
0515814
Right Over Wheel Compt, 51.50"-51.50", Roll Door, Tandem, WI NFPA

0.90 1.80

0.90 0540692
Lights, Side Zone Lower, Wln M6*C LED, Clear Lens, 3pr, Ovr 25 NFPA

5.40 8.10

0.00 0541155
Lights, Rear/Side Up Zone, Wln M9*C LED, Clear Lens 4lts NFPA

4.80 7.20

0.00 0555915
Wiper Control, 2-Speed with Intermittent, MUX, Impel/Velocity NFPA

2.10 8.40

0.00 0563675
Lights, Clearance/Marker/ID, Rear, Truck-Lite 33050R LED 7Lts NFPA

0.35 0.00

0.00 0564535
Light, Marker, Britax Rubber Arm, Model L427.203.L12 LED, Red/Amb, Qty/Loc
NFPA

2.00 0.00

0.00 0564655
Lights, Rear Zn Lwr, Wln M6*C LED, Clear Lens, For Tail Lt Housing
NFPA

1.80 2.70

0.00 0568012
Air Dryer, Wabco System Saver 1200, Heater, 2010
NFPA

7.81 0.00

0.00 0568369
Cab Instruments, Ivory Gauges, Chrome Bezels, Impel/Velocity 2010
NFPA

1.26 0.00

0.00 0595087
DEF Tank, 4.5 Gallon, LS Fill, Forward of Rear Axle
NFPA

0.60 11.40

0.00 0617802
Lights, Perimeter, TecNiq T10-LC00-1 15" LED
NFPA

4.68 0.00

0.00 0620054
Light, Directional/Marker, Intermediate, Weldon 9186-8580-29 LED 2lts
NFPA

0.10 0.90

0.00 0626579
Lights, Perimeter Body, TecNiq T10-LC00-1 15" LED 2lts, Rear Step
NFPA

0.80 0.00

0.00 0626581
Lights, Perimeter Cab, TecNiq T10-LC00-1 15" LED 2Dr
NFPA

0.80 0.00

0.00 0644245
Lights, Interior, 12 VDC, Rom Durolumen R03851, White LED NFPA

8.04 0.00

0.00 0648074
Lights, Clearance/Marker/ID, Front, P25 LED 7 Lts
NFPA

0.49 0.00

0.00 0648425
Light, Directional, Wln 600 Cmb, Cab Crn, Wrp Bzl Out HD Lts, Imp/Vel/AXT/Qtm
NFPA

0.70 0.70

0.00 0649962
Lights, Dome, FRP Dual LED 2 Lts
NFPA

0.40 0.40

0.00 0653937
Flasher, Headlight Alternating
NFPA

0.08 0.00

0.00 0678353
Lights, Exit Indicator, Wln RSR02ZCR Red, RSG02ZCR Green, Spcl Label 1st
NFPA

0.16 0.24

0.00 0757354
Vehicle Data Recorder w/Seat Belt Monitor, w/Rehab Seats & Belted Body Seats
NFPA

0.50 0.00

0.00 0769624
Cab, Velocity FR, Two Door, No Crew Cab
NFPA

6.80 10.20

0.00 0783153
Headlights, Rect LED, JW Spkr Evo 2, AXT/Enf/Imp/Sab/Vel NFPA

4.20 4.20

0.00 0786656
Lightbar, Wln, Freedom IV-Q, 81", RRRRsrRRRWWRRRsrRRRR
NFPA

8.96 2.48

12.40 0791528
Light, Traffic Directing, Wln TAL65, 36.00" Long, TACTL5 NFPA

0.60 1.20

0.00 0804514
Lights, Tail, Wln M62BTT* Red Stop/Tail & M62T* Amber Dir Arw For Hsg
NFPA

0.83 2.49

0.00 0808504
Engine, Cummins X15, 605 hp, 1850 lb-ft, W/OBD, EPA 2027, Velocity
NFPA

6.00 0.00

0.00 0814201
Vehicle Information Center, 7" Color Display, Touchscreen, MUX, CL714
NFPA

1.20 0.00

0.00 0819024
Siren, Wln 295HFS2 Remote, Single Amp, Other Speaker, Non- NFPA 2024
NFPA

1.40 12.60

0.00 0837378
Left Forward Compt, 28" Roll & 60" & 60", Roll and Lap, WI, 2- Door Cab
NFPA

5.40 10.80

5.40 0837379
Right Forward Compt, 28" Roll & 60" & 60", Roll and Lap, WI, 2- Door Cab
NFPA

5.40 10.80

5.40 0887546
Trans, Allison 6th Gen, 4000 EVS P, w/Prognostics,
Imp/Vel/SFR/Enf
NFPA

2.00 2.00

0.00 0889577
Bracket, License Plate & Light, P25 LED, Stainless Brkt NFPA

0.07 0.00

0.00 0889829
Lights, Step, P25 LED, HDR Walk-In
NFPA

0.50 0.00

0.00 0890456
Lights, Cab Access Steps, P25, LED w/Bezel, 1Lt/Step, 2 Door Cab
NFPA

0.50 0.00

0.00 0892618
Not Required, Indicator Light, Pump Panel, No Pump or Skid Pump
NFPA

0.10 0.00

0.00 0897602
Light, Front Zone, Wln M6** M6** M6** M6**, 4 Lts
NFPA

1.80 5.40

1.80 0647728
Alternator, 430 amp, Delco Remy 55SI
S

0.00 0.00

0.00 Load Totals:
101.39
1533.52
394.04
Note: Minimum Continous Load is in "Blocking Right of Way" mode.(Reference current edition of NFPA 1901) Note: Intermittent Load items are not factored in on any alternator load comparisons. These items are included on the report for reference only and should be looked at as amp draw exclusion items. (Reference current edition of NFPA 1901) Note: Total Connected Load "Demand" represents Total Connected Load minus any Load Managed items 259.00
371.00
Alternator Output at Idle:

Alternator Output at Governed Speed:
* UDMC = User Defined Mission Critical, LM = User Defined Load Managed, S = Electrical Amperage Supply 2

Page 123 of 555 ends

Electrical Analysis
1/2/2026
Bid #:
959
Milpitas Fire Walk-In HDR
Sales Rep:

Organization:

Myers, Rich
Golden State Fire Apparatus, Inc
Desc:

Job #:

Customer:

Milpitas Fire Dept.

Option:

Pierce Command Zone, Advanced Electronics & Control
System, Vel WiFi CZT
Type:

Multiplexed
Minimum Continuous Load
Supply:
259.00
Demand:
101.39
Variance:
157.61
Total Connected Load
Supply:
371.00
Demand:
363.59
Variance:

7.41 * UDMC = User Defined Mission Critical, LM = User Defined Load Managed, S = Electrical Amperage Supply 3

Page 124 of 555 ends

Turning Performance Analysis
Bid Number:
959
Chassis:

Velocity Chassis (Big Block), 2010
Department:

Milpitas Fire Dept.

Body:

HDR, Walk-In, Aluminum
Parameters:
*Inside Cramp Angle:
40°
Axle Track:

82.92 in.

Wheel Offset:

4.68 in.

Tread Width:

16.3 in.

Chassis Overhang:
78 in.

Additional Bumper Depth:
19 in.

Front Overhang:
97 in.

Wheelbase:
203.5 in.

Calculated Turning Radii:

Inside Turn:
19 ft. 2 in.

Curb to curb:
33 ft. 1 in.

Wall to wall:
37 ft. 8 in.

Notes:
*Actual Inside cramp angle may be less than shown.

Curb to Curb turning radius calculated for 9.00 inch curb. 01/02/2026
Category
Option
Description
Bumpers
0536235
Bumper, 19" Extended, Steel Painted, Imp/Vel
Tires, Front
0899289
Tires, Front, Goodyear, Armor MAX MSA, 425/65R22.50, 20 ply, Fire Service Load
Axle, Front, Custom
0508846
Axle, Front, Oshkosh TAK-4, Non Drive, 24,000 lb, Velocity Wheels, Front
0660547
Wheels, Front, Accuride, 22.50" x 12.25", Aluminum, Hub Pilot

Page 125 of 555 ends

Definitions:

Inside CrampAngle
Maximum turning angle of the front inside fire.

Axle Track
King-pin to King-pin distance of front axle.

Wheel Offset
Offset from the center line of the wheel to the King-pin.

Tread Width
Width of the tire tread.

Chassis Overhang
Distance of the center line of the front axle to the front edge of the cab. This does not include the bumper depth.

Additional Bumper Wheel
Depth that the bumper assembly adds to the front overhang.

Wheelbase
Distance between the center lines of the vehicles front and rear axles.

Inside Turning Radius
Radius of the smallest circle around which the vehicle can turn.

Curb to Curb Turning Radius
Radius of the smallest circle around which the vehicle's tires can turn. This measures assumes a curb height of 9 inches.

Wall to Wall Turning Radius
Radius of the smallest circle around which the vehicle's tires can turn. This measures takes into account any front overhang due to chassis , bumper extensions and or aerial devices.

Page 126 of 555 ends

4 WARRANTIES

EXHIBIT C
GOLDENSTATEFIRE.COM

Page 127 of 555 ends

Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 2/8/2010 WA0008

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.

This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

No specific exclusions apply
Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4
Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

Fire and Rescue Apparatus
Coverage:

One (1) Year Material and Workmanship
Basic Apparatus
Twelve (12) months.Warranty Period
Ends After:

The date the apparatus is placed in service, or 60 days from the original buyer invoice date, whichever comes first.Warranty Begins:

Portions of the apparatus manufactured by Pierce shall be free from defects in material and workmanship
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.

3. BUYER'S EXCLUSIVE REMEDY.

Page 128 of 555 ends

Fire and Rescue Apparatus
Coverage:

Three (3) Year Material and Workmanship
Velocity and Impel Custom Chassis
Limited Warranty Limited Warranty Limited Warranty Limited Warranty Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

Portions of the apparatus manufactured by Pierce shall be free from defects in material and workmanship

1. LIMITED WARRANTY
(b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; The date the apparatus is placed in service, or 60 days from the original buyer invoice date, whichever comes first. Warranty Begins:

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This limited warranty applies, where applicable, to Goldstar lamination, defroster heater coil and motor blower assembly (excluding the FET PWM module), heater, air conditioning condenser coil and fan/motor assembly, air conditioning evaporator coil and motor blower assembly (excluding the drain pan pump and thermostat), under seat heaters coil and motor blower assembly (excluding the FET PWM module),
HVAC electronic switches, HVAC hoses and hard lines,
heater water valve, Pierce PS6 seat frames and hardware, Pierce One-Eleven mirrors, Pierce hands-free scba holder, cracking or color loss of roto-molded components, Meritor rear axle, Wabco ABS system, cab door handles, Standen
spring suspension components, and the gauge instrument
cluster.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGE S.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE
POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

3. BUYER'S EXCLUSIVE REMEDY.
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce.

Three (3) Years, or
30,000 Miles, or
5000 Engine Hours
Warranty Period
Ends After:

ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

Page 129 of 555 ends

Cummins Warranty
Worldwide
Fire Apparatus/Crash Trucks

Page 130 of 555 ends

Coverage
Products Warranted
This Warranty applies to new diesel Engines sold by
Cummins and delivered to the first user on or after
April 1, 2007, that are used in fire apparatus truck and crash truck* applications Worldwide.

Base Engine Warranty
The Base Engine Warranty covers any failures of the
Engine which result, under normal use and service,
from a defect in material or factory workmanship
(Warrantable Failure). This Coverage begins with the
sale of the Engine by Cummins and ends five years or
100,000 miles (160,935 kilometers), whichever occurs
first, after the date of delivery of the Engine to the first user .

Engine aftertreatment components included in the
Cummins Critical Parts List (CPL) and marked with a
Cummins part number are covered under Base Engine
Warranty.

Additional Coverage is outlined in the Emission
Warranty section.

These Warranties are made to all Owners in the
chain of distribution and Coverage continues to all
subsequent Owners until the end of the periods of
Coverage.

Cummins
Responsibilities
Cummins will pay for all parts and labor needed to
repair the damage to the Engine resulting from a
Warrantable Failure.

Cummins will pay for the lubricating oil, antifreeze,
filter elements, belts, hoses and other maintenance
items that are not reusable due to the Warrantable
Failure.

Cummins will pay for reasonable labor costs for
Engine removal and reinstallation when necessary to
repair a Warrantable Failure.

Cummins will pay reasonable costs for towing a
vehicle disabled by a Warrantable Failure to the
nearest authorized repair location. In lieu of the towing expense, Cummins will pay reasonable costs for
mechanics to travel to and from the location of the
vehicle, including meals, mileage and lodging when
the repair is performed at the site of the failure.

Owner
Responsibilities
Owner is responsible for the operation and
maintenance of the Engine as specified in Cummins
Operation and Maintenance Manuals. Owner is also
responsible for providing proof that all recommended
maintenance has been performed.

Before the expiration of the applicable Warranty,
Owner must notify a Cummins distributor ,authorized
dealer or other repair location approved by Cummins
of any Warrantable Failure and make the Engine
available for repair by such facility. Except for Engines disabled by a Warrantable Failure, Owner must also
deliver the Engine to the repair facility.

Service locations are listed on the Cummins Worldwide
Service Locator at cummins.com.

Owner is responsible for the cost of lubricating oil,
antifreeze, filter elements and other maintenance items provided during Warranty repairs unless such items
are not reusable due to the Warrantable Failure.

Owner is responsible for communication expenses,
meals, lodging and similar costs incurred as a result of a Warrantable Failure.

Owner is responsible for non-Engine repairs and for
‘‘downtime’’expenses, cargo damage, fines, all
applicable taxes, all business costs and other losses
resulting from a Warrantable Failure.

Owner is responsible for a $100 (U.S. Dollars)
deductible per each service visit under this plan in the 3rd, 4th and 5th years of Base Engine Warranty. The
deductible will not be charged during the first 2 years of the Base Engine Warranty.

Limitations
Cummins is not responsible for failures or damage
resulting from what Cummins determines to be abuse
or neglect, including, but not limited to: operation
without adequate coolants or lubricants; overfueling;
overspeeding; lack of maintenance of lubricating,
cooling or intake systems; improper storage, starting,
warm-up, run-in or shutdown practices; unauthorized
modifications of the Engine.

Any unauthorized modifications to the aftertreatment
could negatively effect emissions certification and void Warranty.

Cummins is also not responsible for failures caused by
incorrect oil, fuel or diesel exhaust fluid or by water , dirt or other contaminants in the fuel, oil or diesel

Page 131 of 555 ends

exhaust fluid.

This Warranty does not apply to accessories supplied
by Cummins which bear the name of another
company. Such non-warranted accessories include, but
are not limited to: alternators, starters, fans, air
conditioning compressors, clutches, filters,
transmissions, torque converters, vacuum pumps,
power steering pumps, fan drives and air compressors.

Cummins branded alternators and starters are covered
for the first two years from the date of delivery of the Engine to the first user ,or the expiration of the Base Engine Warranty, whichever occurs first.

Failures resulting in excessive oil consumption are not covered beyond the duration of the Coverage or
100,000 miles (160,935 kilometers) or 7,000 hours from
the date of delivery of the Engine to the first user ,
whichever of the three occurs first. Before a claim for excessive oil consumption will be considered, Owner
must submit adequate documentation to show that
consumption exceeds Cummins published standards.

Failures of belts and hoses supplied by Cummins are
not covered beyond the first year from the date of
delivery of the Engine to the first user or the duration of the Warranty, whichever occurs first.

Parts used to repair a Warrantable Failure may be new
Cummins parts, Cummins approved rebuilt parts or
repaired parts. Cummins is not responsible for failures resulting from the use of parts not approved by
Cummins.

A new Cummins or Cummins approved rebuilt part
used to repair a Warrantable Failure assumes the
identity of the part it replaced and is entitled to the remaining Coverage hereunder .

Cummins Inc. reserves the right to interrogate
Electronic Control Module (ECM) data for purposes of
failure analysis.

CUMMINS DOES NOT COVER WEAR OR WEAROUT
OF COVERED PARTS.

CUMMINS IS NOT RESPONSIBLE FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES.

THIS W ARRANTYAND THE EMISSION W ARRANTY

SET FORTH HEREINAFTER ARE THE SOLE

W ARRANTIESMADE BY CUMMINS IN REGARD TO
THESE ENGINES. CUMMINS MAKES NO OTHER

W ARRANTIES,EXPRESS OR IMPLIED, OR OF

MERCHANT ABILITYOR FITNESS FOR A
P ARTICULARPURPOSE.

This Warranty gives you specific legal rights, and you
may also have other rights which vary from state to
state.

Emission
Warranty
Products Warranted
This Emission Warranty applies to new Engines
marketed by Cummins that are used in the United
States** in vehicles designed for transporting persons
or property on a street or highway. This Warranty
applies to Engines delivered to the first user on or after September 1, 1992.

Coverage
Cummins warrants to the first user and each
subsequent purchaser that the Engine is designed,
built and equipped so as to conform at the time of sale by Cummins with all U.S. federal emission regulations
applicable at the time of manufacture and that it is free from defects in material or factory workmanship which
would cause it not to meet these regulations within the longer of the following periods: (A) Five years or
100,000 miles (160,935 kilometers) of operation,
whichever occurs first, as measured from the date of
delivery of the Engine to the first user or (B) The Base Engine Warranty.

If the vehicle in which the Engine is installed is
registered in the state of California, a separate
California Emission Warranty also applies.

Limitations
Failures, other than those resulting from defects in
material or factory workmanship, are not covered by
this Warranty.

Cummins is not responsible for failures or damage
resulting from what Cummins determines to be abuse
or neglect, including, but not limited to: operation
without adequate coolants or lubricants; overfueling;
overspeeding; lack of maintenance of lubricating,
cooling or intake systems; improper storage, starting,
warm-up, run-in or shutdown practices; unauthorized
modifications of the Engine.

Any unauthorized modifications to the aftertreatment
could negatively effect emissions certification and void Warranty.

Cummins is also not responsible for failures caused by
incorrect oil, fuel or diesel exhaust fluid or by water , dirt or other contaminants in the fuel, oil or diesel
exhaust fluid.

Cummins is not responsible for non-Engine repairs,
‘‘downtime’’expenses, cargo damage, fines, all
applicable taxes, all business costs or other losses
resulting from a Warrantable Failure.

Page 132 of 555 ends

Cummins Inc.

Box 3005
Columbus, IN 47202-3005
U.S.A.

CUMMINS IS NOT RESPONSIBLE FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES.
* Airport operated crash trucks and fire department
operated trucks employed to respond to fires,
hazardous material releases, rescue and other
emergency-type situations.
** United States includes American Samoa, the
Commonwealth of Northern Mariana Islands, Guam,
Puerto Rico and the U.S. Virgin Islands.

Cummins Inc.

Box 3005
Columbus, IN 47202-3005
U.S.A.

Bulletin 3381161
Printed in U.S.A. Rev. 08/09
/H230052001 Cummins Inc.

Page 133 of 555 ends

Page 134 of 555 ends

Page 135 of 555 ends

Page 136 of 555 ends

Page 137 of 555 ends

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

3. BUYER'S EXCLUSIVE REMEDY.

Fire and Rescue Apparatus
Coverage:

Lifetime Fifty (50) Year Structural Integrity
Chassis Frame & Crossmembers
Fifty (50) Years
(Expected Life of Apparatus)
Warranty Period
Ends After:

The date of the original purchase invoice (issued when the product ships from the factory).Warranty Begins:

Custom chassis frame rail and cross members manufactured by Pierce shall be free from defects in material and
workmanship
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This warranty does not apply to damage caused by corrosion.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4

Page 138 of 555 ends

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This limited warranty excludes brake pads, brake rotors, seal boots and shock absorbers.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGE S.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE
POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

Three (3) Years
-or-
30,000 Miles
Warranty Period
Ends After:

ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

Fire and Rescue Apparatus
Coverage:

Three (3) Year Material and Workmanship
TAK-4 Independent Front Suspension
Limited Warranty Limited Warranty Limited Warranty Limited Warranty Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

The TAK-4 Front Independent Suspension and Steering
Gears shall be free from defects in material and
workmanship.

1. LIMITED WARRANTY
(b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:

Page 139 of 555 ends

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This limited warranty excludes brake shoes, brake drums, ball joint boots and shock absorbers.