Staff Report - Cooperative Purchase Contract - Replacement Fire Apparatus [Published for 10-day Review 06-09-2022] — Sacramento City Council, June 21, 2022 (part 2 of 4)

WHAT IS NOT COVERED
 DAMAGE DUE TO ACCIDENT, MISUSE, or ALTERATION — Defects and damage caused as the result of any of the following are not covered:
— Flood, collision, fire, theft, freezing, vandalism, riot, explosion, or objects striking the vehicle; — Misuse of the vehicle;
— Installation into unapproved a pplications and installations; — Alterations or modification of th e transmission or the vehicle, and — Damage resulting from improper storage (refer to long-term st orage procedure outlined in the applicable Allison Service Manual) — Anything other than defects in Allison Transmission material or workmanship NOTE: This warranty is void on transmissions used in vehicles currently or previously titled as salvaged, scrapped, junked, or totale d.  CHASSIS, BODY, and COMPONENTS — The chassis and body company (assemblers) and other component and equipment manufacturers are solely responsible for warranties on the chassis, body, component(s), and equipment they provide. Any transmission repair caused by an alteration(s) made to the Allison transmission or the vehicle which allows the transmission to be installed or operated outside of the limits defined in the appropriate Allison Installation Guideline is solely the responsibility of the entity making the alteration(s).  DAMAGE CAUSED by LACK of MAINTENANCE or by th e USE of TRANSMISSION FLUIDS NOT RECOMMENDED in the OPERATOR’S MANUAL — Defects and damage caused by any of the following are not covered:
— Failure to follow the recommendations of the maintena nce schedule intervals applicable to the transmission; — Failure to use transmission fluids or maintain transm ission fluid levels recommended in the Operator’s Manual.  MAINTENANCE — Normal maintenance (such as replacement of filters, screens, and transmission fluid) is not covered and is the owner’s responsibility.
 REPAIRS by UNAUTHORIZED DEALERS — Defects and damage caused by a service outlet that is not an authorized Allison Transmission Distributor or Dealer are not covered.
 USE of OTHER THAN GENUINE ALLISON TRANSMISSION PARTS — Defects and damage caused by the use of parts that are not genuine Allison Transmission parts are not covered.  EXTRA EXPENSES — Economic loss and extra expenses are not covered. Examples include but are not limited to: loss of vehicle use; inconvenience; storage; payment for loss of time or pay; vehicle rental expense; lodging; meals; or other travel costs.  “DENIED PARTY” OWNERSHIP — Warranty repair parts and labor costs are not reimbursed to any participating or non-participating OEMs, dealers or distributors who perform warranty work for, or on behalf of, end users identified by the United States as being a “denied party” or who are citizens of sanctioned or embargoed countries as defined by the U.S. Department of Treasury Office of Foreign Assets Control. Furthermore, warranty reimbursements are not guaranteed if the reimbursement would be contrary to any United States export control laws or regulations as defined by the U.S. Department of Commerce, the U.S. Department of State, or the U.S. Department of Treasury.

OTHER TERMS APPLICABLE TO CONSUMERS AS DEFINED by the MAGNUSON-MOSS WARRANTY ACT This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

Allison Transmission does not authorize any person to create for it any other obligation or liability in connection with these transmissions.

ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE APPLICABLE TO THESE TRANSMISSIONS IS LIMITED IN DURATION TO THE DURATION OF THIS WRITTEN WARRANTY.

PERFORMANCE OF REPAIRS AND NEEDED ADJUSTMENTS IS THE EXCLUSIVE REMEDY UNDER THIS WRITTEN WARRANTY OR ANY IMPLIED WARRANTY. ALLISON TRANSMISSION SHALL NOT BE LIABLE FOR INCIDENTAL OR

CONSEQUENTIAL DAMAGES (SUCH AS, BUT NOT LIMITED TO, LOST WAGES OR VEHICLE RENTAL EXPENSES) RESULTING FROM BREACH OF THIS WRITTEN WARRANTY OR ANY IMPLIED WARRANTY.** ** Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you.

OTHER TERMS APPLICABLE TO OTHER END-USERS

THIS WARRANTY IS THE ONLY WARRANTY APPLICABLE TO THE ALLISON TRANSMISSION MODELS LISTED

ABOVE AND IS EXPRESSLY IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. ALLISON

TRANSMISSION DOES NOT AUTHORIZE ANY PERSON TO CREATE FOR IT ANY OTHER OBLIGATION OR LIABILITY IN CONNECTION WITH SUCH TRANSMISSIONS. ALLISON TRANSMISSION SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM BREACH OF THIS WARRANTY OR ANY IMPLIED WARRANTY.

QUESTIONS
If you have any questions regarding this warranty or the performance of warranty obligations, you may contact any Allison Transmission Distributor or Dealer or write to:

Allison Transmission, Inc.

P.O. Box 894
Indianapolis, IN 46206-0894
Attention: Warranty Administration PF-9

Form SE0616EN (201009)

Page 2 of 2 ends

Warranty Begins:

The transmission cooler shall be free from component or structural failures caused by defects in material and/or workmanship. Collateral damage up to $10,000 per
occurrence is available for the first three (3) years.
(b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; (d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce.

Five (5) Years on Oil Cooler and three (3) years on collateral damage coverage
Warranty Period
Ends After:

Fire and Rescue Apparatus
Coverage:

Five (5) Year Material and Workmanship - Transmission Oil Cooler Three (3) Year Collateral Damage Coverage

1. LIMITED WARRANTY
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

The date of delivery to the first retail purchaser.

This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This warranty does not cover repair due to accidents,
misuse, and excessive vibration, flying debris, storage damage (freezing), negligence or modification. This warranty is void if any modification or repairs are performed without authorization. This also voids any future warranty.

This warranty does not cover cost of maintenance or repairs due to lack of required maintenance services as
recommended. Performance of the required maintenance
and use of proper fluids are the responsibility of the owner.

Towing is covered to the nearest distributor or authorized dealer only when necessary to prevent further damage to your transmission.

Labor costs for the removal and reinstallation of goods may be covered when necessary to make repairs. Please contact your OEM for authorization.

Replacement of cooler during the warranty period is limited to 100% of reasonable labor costs up to a maximum of $700 to remove, replace, or repair the oil cooler.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE
POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.

Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.

3. BUYER'S EXCLUSIVE REMEDY.

Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle.
2/22/2012 WA0216
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES

ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

2. DISCLAIMERS OF WARRANTIES
capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.

United Plastic Fabricating, Inc. (hereinafter called “UPF”) warrants each POLY-TANK®, Booster/Foam Tank POLYSIDE® Wetside Tank, Integrator Tank/Body, ELLIPSE™ Elliptical Tank, Ellip-T-Tank Tank and DEFENDER™ Skid Tank to be free from defects in material and workmanship for the service life of the original vehicle (vehicle must be actively used in an emergency re- sponse for fire suppression). All UPF Tanks must be installed and operated in accordance with the UPF Installation and Operating Guidelines. Failure to do so can void the warranty.

Every UPF Tank is inspected and tested before leaving our facility. Should your UPF Tank require service, please notify UPF via email, fax, in writing or by calling UPF at 1-978-975-4520. Please provide the serial number, a de - scription of the service request, the location along with the phone number and name of the contact person. Our goal is to have scheduled work completed within a reasonable time period.

Under a valid warranty claim, UPF will cover the cost to repair the UPF Tank including the customary and reasonable costs to make the tank accessible such as the removal and reinstallation of the tank if authorized in advance (pre-approved) by UPF. The warranty will not cover tanks that have been im- properly installed, operated, misused, abused, or modified from its intended or designed use. Serial number must not have been altered, defaced or re - moved. Tanks that are not stored or installed properly which results in the tank suffering UV damage will not be covered by this agreement.

Should UPF determine that the service claim is valid under this warranty for a tank located outside of the United States and Canada, UPF will assume the costs for labor and material for the warranty repair as described above plus all travel costs to the U.S. port of embarkation. Costs for airline travel outside of the U.S. and Canada will not be the responsibility of UPF.

In the event the tank shall become stationed in an area of the world that is considered to be a war zone or where unsafe conditions exist for the safe passage of United States Nationals, as reported by the United States Depart- ment of State, (http://www.state.gov), and a request to perform service or warranty repairs, UPF reserves the right to refuse to honor such requests. It is the purchaser’s responsibility to relocate the tank to an area where such repairs can be performed without undue risk to UPF employees or their des - ignee. UPF will make every reasonable effort to support our products though alternative means.

For Ellipse™ elliptical tanks, a separate five year warranty provided by the subcontractor is applied to the sub-frames, chute linings (rubber isolation strips) and metal components. The stainless steel wrap provided by UPF shall be warranted by the subcontractor performing the wrap installation in accordance with their warranty in place at the time of the installation. UPF will not be liable for any warranty costs associated with the wrap, sub-frames, chute linings (rubber isolation strips) and metal components but will assist with all claims on behalf of its customer.

For PolySide® wetsided tanks and Integrator™ Tank/Body units, all polypro- pylene components related to the tank shall carry the standard UPF lifetime FOR: POLY-TANK®, POLYSIDE®, INTEGRATOR™, ELLIPSE™, ELLIP-T-TANK™ & DEFENDER™

WARRANTY
UNITED PLASTIC FABRICATING, INC.

LIFETIME SERVICE WARRANTY
Continued on back
E f f e c t i v e 1 A u g u s t , 2 0 0 9
service warranty. Other polypropylene components, including but not limited to compartments, wheel wells, fenders and other body related components shall be warranted by UPF for a period of ten years. The warranty for the PolySide® and Integrator™ units excludes paint or hardware, which shall be covered by the manufacturer of the paint/hardware.

All UPF tanks 50 gallons or less utilized for non-fire applications and installed on specialty vehicles such as ATVs, trailers, boats, etc. are covered under a separate warranty policy available from UPF. Further, UPF Protector™ foam and water trailers are warranted under a separate warranty policy available from UPF.

This UPF warranty is transferable within the United States only with prior writ- ten approval by UPF (except an original apparatus manufacturer may assign this warranty to the first titled owner/lessee of the apparatus).

UPF will NOT reimburse any unnecessary work and/or work that has not been pre-approved. Any and all third party charges must be pre- authorized and approved in writing by UPF prior to commencing the work. Any unauthorized third party repairs, alterations, actions or modi- fications will not be covered and can void the warranty. UPF will be the sole determining authority as to whether a service claim will be valid and covered under this warranty.

In no event will UPF be liable for an amount in excess of the purchase price of the booster/foam tank at the time of manufacture or for any loss or dam - age, whether direct, indirect, incidental, consequential, or otherwise arising out of failure of its product. Loss of contents (water, foam, etc.) shall not be the responsibility of UPF. Further, UPF is not responsible for costs associated with service repairs to chassis, sub-frames, bodies, valves, dumps, hoses, pressure vacuum vents, and other components (i.e. liquid level transducers, etc.). Further, UPF will not cover the cost for travel of the vehicle to and from a repair facility.

This warranty contains the entire warranty. It is the sole warranty and price agreements or representation, whether oral or written, are either merged herein or expressly cancelled. UPF neither assumes, nor authorizes any per- son supposing to act on its behalf to change, nor assume for it, any warranty or liability concerning its product.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do not allow exclusion or limitation or incidental or consequential damage, so the above limitation or exclusion may not apply to you. Since some states do not allow limitations on the length of an implied warranty, the above limitation may not apply to you.

THERE ARE NO WARRANTIES, EXPRESSED OR IMPLIED, WHICH EX - TEND BEYOND THE DESCRIPTION OF THE FACE HEREOF. THERE IS

NO EXPRESS OR IMPLIED WARRANTY OF MERCHANTABILITY OR A
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. ADDITION -

ALLY, THIS WARRANTY IS IN LIEU OF ALL OTHER OBLIGATION OR LIABILITIES ON THE PART OF UPF.

FOR: POLY-TANK®, POLYSIDE®, INTEGRATOR™, ELLIPSE™, ELLIP-T-TANK™ & DEFENDER™

WARRANTY
UNITED PLASTIC FABRICATING, INC.

POLY-TANK®,& POLYSIDE® are registered trademarks of UPF, Inc. INTEGRATOR™, ELLIPSE™, ELLIP-T-TANK™ & DEFENDER™ are trademarks of UPF, Inc. © 08/01/09 UPF, Inc. Printed in the USA 2 6 0 0 A M E R I C A N D R I V E • A P P L E T O N , W I 5 4 9 1 2- 2 0 1 7 • 9 2 0- 832 - 3 000

P I E R C E M A N U F A C T U R I N G I N C .

B U L L E T I N

TO: All Dealer Service Representatives

From: Kevin Hanegraaf

DATE: January 4, 2010

RE: UPF Tank Warranty Policy – Truck in Accident

Service Topic #292

To keep the UPF tank warranty valid on trucks that have been involved in a vehicular accident, it is UPF’s policy that the customer must remove the tank from the truck and send it back to one of UPF’s facilities for inspection. In the event that this does not take place, the warranty will be considered null and void.

The customer must remove and send the tank back to UPF for inspection in order to maintain the original warranty coverage, at which time it will be:
- Filled with water
- Visually inspected
- Ultraviolet spark tested on articulating test stand in the dark - Recommendation for repairs if necessary provided by UPF - Fully evaluated and repaired by UPF

If your customer chooses to leave the tank on the truck and wants a technician to inspect and/or repair the tank in the field, then the warranty is no longer in effect.

This direction is upheld by UPF because the technician cannot inspect the entire tank when it is still installed on the truck.

Note: This memo is intended to relay the information Pierce has received on UPF’s tank warranty for trucks that are in a vehicular accident. In the event of an actual claim, we direct you to consult with UPF’s service Manager Maura Watts (800-638-8265 x253)

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This warranty applies only to the body tubular support and mounting structures and other structural components of the body of the vehicle model, as identified in the Pierce
specifications for the Fire and Rescue Apparatus.

This warranty does not apply to damage caused by corrosion.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4
Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

Fire and Rescue Apparatus
Coverage:

Ten (10) Year Structural Integrity
Apparatus Body
Ten (10) Years
- or -
100,000 Miles
Warranty Period
Ends After:

The date of the original purchase invoice (issued when the product ships from the factory).Warranty Begins:

The apparatus body shall be free from structural failures caused by defects in material and workmanship
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

3. BUYER'S EXCLUSIVE REMEDY.

Effective March 15, 2010

AMDOR Inc. TERMS OF BUSINESS AND GENERAL INFORMATION

Warranty:

All AMDOR Inc. roll-up door products are warr anted for a period of 10 years from the date of delivery (with the exception of wet paint adhesion - please see below). AMDOR Inc. liability covers the replacement or repai r of any component that fails due to defects in material and / or workmanship during the coverage period. We accept no liability for claims made for damages to any part (or parts ) of a vehicle and / or machine (of any type) or injury claims by a person or persons assumed or alleged to have been brought about by the use or misuse of any product supplied by AMDOR Inc. Warranty coverage does not extend to door atta chments including (but not lim ited to) decals, emblems, stripes and adhesives.

In order to initiate the claims process pl ease contact your authoriz ed representative of AMDOR Inc. Warranty claims must be acco mpanied by a written description providing full and reasonable details as to the nature of the defect. Upon receipt of your claim arrangements will be made to inspect the defective produc t (if necessary). Justified warranty claims will be repair ed, exchanged, or credited to the customer's account at AMDOR Inc.'s discretion. All warranty claims must be approved in writing by the Customer Service Manager for AMDOR Inc. There are no exceptions to this clause.

Limited warranty coverage in cludes the labor associated with the disassembly and assembly of products deemed to be defective by AMDOR Inc. Labor allowances are based on a set time schedule as determined by AMDOR Inc. The maximum allowable hourly labor rate is $ 50. A ll warranty labor claims must be approved in writing by an authorized representative of AMDOR Inc. prior to commenc ement of work. Allowances for removal and installation:

Curtain replacement: 3/4 hour
Balancer replacement: 1 hour
Door ajar switch 3/4 hour
Bottom Panel Assembly: 1/2 hour
Slat replacement: 3/4 hour
Door removal and replacement 1 1/2 hours

Items authorized for return must be acco mpanied by a Return Goods Authorization (RGA) number. We will accept collect sh ipments of items de emed to be defective provided that they are returned via the mo st economical carrier. Should items be returned by means other than the most economical carrier the difference will be charged back to the sender.

AMDOR Inc. reserves the right to reject any claim when a product has been opened, interfered with or modified. Claims may also be rejected when damage to the product (or any sub-assembly) has been brought about by accident, misuse, abuse, vandalism, incorrect installation, temperature extremes, chemical exposure or any factor other than regular operating conditions.

Limited Wet Paint Match Adhesion Warranty

AMDOR Inc. warrants wet paint finishes applied by AMDOR utilizing our approved factory paint specification. All wet paint matc h colors must be approved in writing by an authorized OEM representative. AMDOR Inc. will provide a color spray out for this purpose. The time required for shipping and cons ideration of initial color spray outs will be considered over and above stated lead time s. Warranty coverage will extend for a period of not less than 5 years from the date of delivery as determined by AMDOR Inc.'s Packing Slip. AMDOR reserves the right to determine whether individual units will be replaced and / or repaired by an AMDOR approved vendor. An allowance will be made for labor associated with the disassembly and assembly of individual units at the prescribed hourly rate of $ 50 per hour. Compensation for labor will not exceed the maximum time allowance permitted for door removal and replacement. Written approval including specified allowance for time must be obtained from AMDOR prior to initiating work. Warranty coverage will ext end to the following visible paint system defects:

1./ Loss of mechanical adhesion as eviden ced by peeling, cr acking or blistering which exposes the substrate material.

2./ Corrosion of the substrat e due to paint system failure.

3./ Fading which results in a subs tantial departure from the primary AMDOR approved body color.

Wet paint adhesion limited warranty coverage will be excluded when damages to the system are determined by AMDOR Inc. to be a result of the following:

1./ Damage caused through the use of atta chments including (but not limited to) decals, labels, adhesives, non factory approved coatings.

2./ Loss of gloss, discoloration or damage due to improper maintenance (including but not limited to) mechanical wash systems, pressure washers, steam cleaners, non approved wash or polishing agents.

3./ Abuse, acts of nature, excessive heat / cold, chemical exposure, vandalism and / or accidents.

4./ Scratches, chips, abrasions, or dents from any source.

This document supercedes all previous written and / or verbal warranties provided by AMDOR Inc. and / or it's affiliates.

Waterous Company
125 Hardman Avenue South
South St. Paul, MN 55075 USA
www.waterousco.com
F-2891 (04/15/20)
Waterous Seven-Year Limited Warranty
WATEROUS warrants, to the original Buyer only, that products manufactured by WATEROUS will be free from defects in material and workmanship under normal use and service for a period of seven (7) years from the date the product is first placed in service, or seven and one-half (7-1/2) years from the date of shipment by WATEROUS, whichever period shall be the first to expire; provided the Buyer notifies WATEROUS, in writing, of the defect in said product within the warranty period, and said product is found by WATEROUS to be nonconforming with the aforesaid warranty. When required in writing by WATEROUS, defective products must be promptly returned by Buyer to WATEROUS at WATEROUS’ plant at South St. Paul, Minnesota, or at such other place as may be specified by WATEROUS, with transportation and other charges prepaid. A Returned Material Authorization (RMA) is required for all products and parts and may be requested by phone, fax, email, or mail. The aforesaid warranty excludes any responsibility or liability of WATEROUS for:
(a) damages or defects due to accident, abuse, misuse, abnormal operating conditions, negligence, accidental causes, use in non-firefighting applications, or improper maintenance, or attributable to written specifications or instructions furnished by Buyer; (b) defects in products manufactured by others and furnished by WATEROUS hereunder, it being understood and agreed by the parties that the only warranty provided for such products shall be the warranty provided by the manufacturer thereof which, if assignable, WATEROUS will assign to Buyer, if requested by Buyer;
(c) any product or part, altered, modified, serviced or repaired other than by WATEROUS, without its prior written consent; (d) the cost of dismantling, removing, transporting, storing, or insuring the defective product or part and the cost of reinstallation; and (e) normal wear items (packing, strainers, filters, light bulbs, anodes, intake screens, mechanical seals, etc.).

ALL OTHER WARRANTIES ARE EXCLUDED, WHETHER EXPRESS OR IMPLIED BY OPERATION OF LAW OR OTHERWISE, INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT, WHETHER AS A RESULT OF BREACH OF

CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE), STRICT LIABILITY, OR ANY OTHER CAUSE OF ACTION, SHALL WATEROUS BE LIABLE FOR ANY PUNITIVE, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR FOR PERSONAL INJURY OR PROPERTY DAMAGES.

The exclusive remedy of Buyer and the sole liability of WATEROUS, whether based on contract, warranty, tort or any other basis of recovery whatsoever, is expressly limited at the election of WATEROUS to:
(a) the replacement at the agreed point of delivery of any product or part, which upon inspection by WATEROUS or its duly authorized representative, is found not to conform to the limited warranty set forth above, or (b) the repair of such product or part, or
(c) the refund or crediting to Buyer of the net sales price of the defective product or part.

BUYER’S REMEDIES CONTAINED HEREIN ARE EXCLUSIVE OF ANY OTHER REMEDY OTHERWISE AVAILABLE TO BUYER.

Warranty Begins:

Stainless steel piping shall be free from structural failures caused by defects in material and workmanship, or
perforation caused by corrosion.
(b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; (d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce.

Ten (10) Years
- or -
100,000 Miles
Warranty Period
Ends After:

Fire and Rescue Apparatus
Coverage:

Ten (10) Year Material and Workmanship
Stainless Steel Piping

The date of the original purchase invoice (issued when the product ships from the factory).

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

Pierce’s obligation under this warranty is limited to repairing or replacing without charge, as Pierce may elect, the
stainless steel piping or components which Pierce
determines to have failed due to defective material and workmanship, or perforation caused by corrosion.

This warranty does not cover the use of fluoroprotein (FP) type foam. The sodium chloride within FP foam can cause long-term damage to system components if not thoroughly flushed immediately after use.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

3. BUYER'S EXCLUSIVE REMEDY.

Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle.
3/22/2012 WA0035
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES

ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

2. DISCLAIMERS OF WARRANTIES
capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This limited warranty is applicable to the vehicle in the following percentage costs of warranty repair, if any:

Topcoat Durability & Appearance: Gloss, Color Retention & Cracking
0-72 months 100%
73-96 months 50%
97-120 months 25%
Integrity of Coating System: Adhesion, Blistering/Bubbling 0-36 months 100%
37-84 months 50%
85-120 months 25%
Corrosion: Dissimilar Metal and Crevice
0-36 months 100%
37-48 months 50%
49-72 months 25%
73-120 months 10%
Corrosion Perforation
0-120 months 100%
This limited warranty applies only to exterior paint. Paint on the vehicle's interior is warranted only under the Pierce Basic One Year Limited Warranty.

Items not covered by this warranty include:
(a) Damage from lack of maintenance and cleaning (proper cleaning and maintenance procedures are detailed in the Pierce operation and maintenance manual).
(b) UV paint fade.
(c) Any cab not manufactured by Pierce.

Conditions and
Exclusions:

Fire and Rescue Apparatus
Coverage:

Ten (10) Year Pro-Rated Paint and Corrosion
Custom Body
Ten (10) YearsWarranty Period
Ends After:

The date of the original purchase invoice (issued when the product ships from the factory).Warranty Begins:

Exterior surfaces of the body shall be free from blistering, peeling, corrosion or any other adhesion defect caused by defective manufacturing methods or paint material selection. (d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

3. BUYER'S EXCLUSIVE REMEDY.

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This warranty does not cover damage from lack of
maintenance and cleaning (proper cleaning and maintenance procedures are detailed in the Pierce operation and
maintenance manual).

Conditions and
Exclusions:

Fire and Rescue Apparatus
Coverage:

Three (3) Year Material and Workmanship
Goldstar® Gold Leaf Lamination
Three (3) YearsWarranty Period
Ends After:

The date of the original purchase invoice (issued when the product ships from the factory).Warranty Begins:

Each Goldstar® gold leaf lamination shall be free from
defects in material and workmanship.
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

3. BUYER'S EXCLUSIVE REMEDY.

PRODUCT

PROPOSAL
Exhibit “A”
Bid #771

PROPOSAL PREPARED FOR
City of Sacramento
Pierce Manufacturing, Inc.

International 4x4 Type 3 Engine
HGAC FS12-19, Code FS19BC03
May 24, 2022

SALES CONSULTANT
Brad Hansen
Golden State Fire Apparatus, Inc.
7400 Reese Road
Sacramento, CA 95828
916.869.6072 Cell
[email protected]

PARTS, SERVICE & SUPPORT
Golden State Emergency Vehicle Service, Inc.
7400 Reese Road
Sacramento, CA 95828
916.330.1638 Office
[email protected]

Page 2 of 3 ends

www.goldenstatefire.com
7400 Reese Road
Sacramento, CA 95828
Office 916.330.1638
Fax 916.330.1649

PROPOSAL PREPARED FOR:

City of Sacramento
5770 Freeport Blvd, Suite 2
Sacramento, CA 95822

We hereby propose and agree to furnish, after your acceptance of this proposal and the proper execution by the CITY OF SACRAMENTO, hereinafter called “Customer” and an officer of Golden State Fire Apparatus, Inc., hereinafter called “GSFA”, the following fire apparatus and equipment, hereinafter called “Product”:

PROPOSAL SUMMARY
This proposal includes the following items in accordance with the specifications hereto attached:
 Fire apparatus and equipment
 100% performance bond
 Pre-delivery inspection/services by GSFA
 Delivery to GSFA service center in Sacramento
 Final delivery from service center to Customer
 Demonstration and familiarization of the Product

PRODUCT COMPLETION
Product shall be built in accordance with the specifications hereto attached, delays due to acts of God, strikes, war, or intentional conflict, failures to obtain chassis, materials, unusual weather conditions or other causes beyond GSFA’s control not preventing, within approximately 375 to 405 CALENDAR DAYS after receipt of this order and the acceptance thereof at our Sacramento, California office. Within thirty (30) calendar days after receipt of this order and acceptance thereof, GSFA shall submit to Customer a production schedule including tentative pre-construction conference, final inspection and final delivery dates.

DELIVERY LOCATION
Product shall be shipped in accordance with the specifications hereto attached and be delivered to you at SACRAMENTO, CALIFORNIA. Proof of insurance must be demonstrated by the Customer to GSFA prior to transferring of the Product(s).

Submitted Date: May 24, 2022
Proposal Number: 10524-22B
Expiration
Date: July 8, 2022
Sales Consultant: Brad Hansen
# Description Unit Price
A One (1) Pierce Manufacturing, Inc. STOCK/DEMO (job 37700) International 4x4 Type 3 Engine
635,248.68
B Discount for HGAC contract FS12-19, Product Code FS19VB03 (6,079.00) C Discount For 100% Pre-Payment at Time of Order (6,285.81)

SUBTOTAL 622,883.87

8.75% State Sales Tax 54,502.34
California Tire Fee 10.50
GRAND TOTAL 677,396.71

740
0 Reese Road, Sacramento, CA 95828 | Office 916.330.1638 | Fax 916.330.1649

Page 3 of 3 ends

ACCEPTING THIS PROPOSAL
In the event Customer wishes to purchase the Product described in this Proposal and the attached specifications, then, prior to the expiration date listed on page 2 of this Proposal, Customer shall sign and return this Proposal. Thereafter, GSFA and Customer will endeavor to enter into a purchase agreement incorporating this Proposal and including additional terms (a “Purchase Agreement”). If Customer returns a signed copy of this Proposal alone, GSFA will send Customer its form of Purchase Agreement for Customer’s review and signature. If Customer desires to use its standard form of purchase order as the Purchase Agreement, then Customer should return a signed copy of this Proposal along with a copy of such purchase order. All purchase orders shall be made out to GSFA. GSFA will review such purchase order and contact the Customer regarding any required revisions. Only upon a full execution of a Purchase Agreement shall GSFA and Customer be obligated to purchase and sell the Product set forth in this Proposal.

RMS AND CONDITIONS
The following Terms and Conditions are hereby made part of this Proposal:

1. Payment Terms, 100% Pre-Payment at Time of Order – Customer shall pay the amount listed on page one of this Proposal, which includes: (i) the total price for the Product (the “Purchase Price”), (ii) the estimated state sales tax on the Product, and (iii) the California tire fee (together with the Purchase Price and estimated state sales tax, the “Grand Total”) within fifteen (15) calendar days from the date on which the Purchase Agreement is fully executed. The proposed delivery timeframe for the Product, which is outlined on page one of this Proposal, shall not begin until full payment of the Grand Total is received. In the event Customer does not pay GSFA the Grand Total in the timeframe set forth in this Section 1, GSFA may, in its sole discretion, cancel the Purchase Agreement entered into between the parties.

2. Commercial Chassis Price Volatility – GSFA shall not be responsible for any commercial chassis price increase or surcharge enacted by a commercial chassis Original Equipment Manufacturer (OEM) after the execution of contract or issuance of Purchase Order. Any commercial chassis price increase or surcharge will be passed through to the Customer at cost and will be documented in writing on a Change Order. Customer shall pay any commercial chassis price increase or surcharge prior to final delivery or pick up to Customer location.

3. Stock / Demo Units – If applicable, any stock/demo units, including those identified by this Proposal, are available for sale on an as -is, first- come and first served-basis. Regardless of this Proposal, the first Customer to enter into a Purchase Agreement identifying any such stock/demo unites shall obtain said units.

4. Order Changes – The Customer may request that GSFA incorporate a change to the Product or the Specifications for the Product by delivering a written change order to GSFA, which shall include a description of the proposed change sufficient to permit GSFA to evaluate the f easibility of such change (a “Change Order”). GSFA will provide Customer a written response (a “Response”) stating (i) whether GSFA will accommodate such Change Order (which GSFA may decide in its sole and absolute discretion) and (ii) the terms of the modification to the order, including any increase or decrease in the Purchase Price resulting from such Change Order, and any effect on production scheduling or Delivery resulting from such Change Order. Customer shall have seven (7) days after receipt of the Response to notify GSFA as to whether Customer desires to make the changes GSFA has approved in the Response. In the event Customer counter-signs GSFA’s Response, Customer shall pay the increase (or be refunded the decrease) in the Purchase Price prior to final delivery to Customer location
.
5 . Force Majeure – GSFA shall not be responsible nor deemed to be in default on account of delays in performance due to causes which are beyond GSFA’s and manufacturer’s control and which make GSFA’s performance impracticable, including but not limited to wars, insurrections, strikes, riots, fires, storms, floods, other acts of nature, explosions, earthquakes, accidents, any act of government, delays in transportation, inability to obtain necessary labor supplies or manufacturing facilities, allocation regulations or orders affecting materials, equipment, facilities or completed products, failure to obtain any required license or certificates, acts of God or the public enemy or terrorism, failure of transportation, epidemics, quarantine restrictions, failure of vendors (due to causes similar to those within the scope of this clause) to perform their contracts or labor troubles causing cessation, slowdown, or interruption of work. 6 . Cancellation/Termination – In the event Customer and GSFA enter into a Purchase Agreement and Customer thereafter cancels or terminates the Purchase Agreement, GSFA will charge a cancellation fee as follows: (a) 10% of the Purchase Price after order is accepted and entered by GSFA; (b) 20% of the Purchase Price after completion of the pre -construction phase of the order process; and (c) 50% of the Purchase Price after the requisition of any materials or commencement of any manufacturing or assembly of the Product by either GSFA or the manufacturer of the Product. The tier of cancellation fee applicable to any cancellation shall be in the sole and absolute discretion of GSFA.
7 . State Sales Tax – Customer shall be responsible for the cost of state sales tax associated with, or attributable to the Product. The taxes owed by Customer for the Product is subject to adjustment for the applicable state sales tax rate in effect when the Product is delivered to the Customer. Therefore, the sales tax will be increased or decreased at the time of delivery if a change in the sales tax rate has occurred, in which case Customer shall pay GSFA (or be refunded by GSFA) the applicable change in sales tax.
8 . Proposal Expiration – After the Expiration Date shown on page one of this Proposal, Customer shall require GSFA’s written consent to accept this Proposal.
9 . Governing Law – This Proposal is to be governed by and under the laws of the state of California.

Thank you for providing Golden State Fire Apparatus, Inc. with the opportunity to provide this proposal. If you have any questions regarding the options presented or need additional options, please contact me.

S
incerely, I, _______________________________________________________________authorized representative of CITY OF SACRAMENTO agrees to purchase the proposed Product(s) and agree to the terms and conditions of this proposal and the specifications hereto attached.

B
rad Hansen SIGNATURE: __________________________________________________________________________ Golden State Fire Apparatus, Inc.

TITLE: _______________________________________ __________ DATE: ____________________

PRODUCT

SPECIFICATIONS
Exhibit “B”
Bid #771

Proposal Details Report
OptionCode
Type
Option
ProposalText
0765490
SP
Wildland, BX3, International, 1000
GPM Pump (SF-3204)
0766594
Boiler Plates,1906, Wildland

Golden State Fire Apparatus Inc
is pleased to submit a proposal to
City of Sacramento
for a
Pierce® wildland fire apparatus
per your request for quotation. The following paragraphs will describe in detail the apparatus proposed. It meets the applicable requirements of the National Fire Protection Association (NFPA) as stated in current edition at time of contract execution, except where amended by your specifications. Loose equipment not specifically requested will not be provided.

PIERCE MANUFACTURING was incorporated in
1913
. Since then we have been building bodies
with one (
1 ) philosophy, "BUILD THE FINEST". Our skilled craftsmen take pride in their work, which is reflected, in the final product. We have been building fire apparatus since the early "forties" giving Pierce Manufacturing over
75 years of experience in the fire apparatus market.

Pierce Manufacturing has built and put into service more than 28,500
apparatus on commercial
chassis, and more than
33,900
on Pierce custom chassis designed and built specifically for fire and emergency applications. Our Appleton, Wisconsin facility has over 870,000
total square feet
of floor space situated on approximately
105
acres of land. Our Bradenton, Florida facility has
300,000
square feet of floor space situated on approximately
38 acres of land. A multi-million
dollar inventory of parts is available to keep your unit in service long after it has left the factory.

Our beliefs in high ethical standards are carried through in all of our commitments and to everyone with whom we do business. Honesty, Integrity, Accountability and Citizenship are global tenets by which we all live and work. Consequently, we neither engage in, nor have we ever been convicted of price fixing, bid rigging, or collusion in any domestic or international fire apparatus market.

Pierce has only one brand of fire apparatus "Pierce", ensuring you are receiving top of the line product that meets your specification.

In accordance with the current edition of NFPA
1906
standards, this proposal will specify whether
the fire department, manufacturer, or apparatus dealership will provide required loose equipment.

Images and illustrative material in this proposal are as accurate as known at the time of publication, but are subject to change without notice. Images and illustrative material is for reference only, and may include optional equipment and accessories and may not include all standard equipment.

GENERAL DESIGN AND CONSTRUCTION
To control quality and ensure the compatibility of all the components, Pierce specifically designs the pump module, body, and electrical system to properly integrate and function with the commercial cab and chassis.

All welding, assembly and paint work will be done in Pierce owned manufacturing facilities. This includes, but not limited to the pumphouse module assembly, the body and the electrical system.

QUALITY AND WORKMANSHIP
Pierce has set the pace for quality and workmanship in the fire apparatus field. Our tradition of building the highest quality units with craftsmen second to none has been the rule right from the beginning and we demonstrate that ongoing commitment by: Ensuring all steel welding follows American Welding Society D

1.1-2004
recommendations for structural steel welding. All aluminum welding follows American Welding society and ANSI D

1.2-2003
requirements for structural
welding of aluminum. All sheet metal welding follows American welding Society B

2.1-2000

requirements for structural welding of sheet metal. Our flux core arc welding uses alloy rods, type 7000
and is performed to American Welding Society standards A

5.20 -E
70 T
1 . Furthermore, all
employees classified as welders are tested and certified to meet the American welding Society codes upon hire and every three (
3 ) years thereafter. Pierce also employs and American Welding Society certified welding inspector in plant during working hours to monitor weld quality.

Pierce Manufacturing operates a Quality Management System under the requirements of ISO 9001
. These standards sponsored by the International Organization for Standardization (ISO) specify the quality systems that are established by the manufacturer for design, manufacture, installation and service. A copy of the certificate of compliance is included with this proposal.

In addition to the Quality Management system, we also employ a Quality Achievement Supplier program to insure the vendors and suppliers that we utilize meet the high standards we demand.

That is just part of our overall "Quality at the Source" program at Pierce.

To demonstrate the quality of our products and services, a list of at least twenty five (
25 )
fire
departments/municipalities that have purchased vehicles for a second time is provided.

DELIVERY
The apparatus will be delivered under its own power to insure proper break-in of all components while the apparatus is still under warranty.

A qualified delivery representative shall deliver the
apparatus and remain for a sufficient length of time to instruct personnel in proper operation, care and maintenance of the equipment delivered.

MANUAL AND SERVICE INFORMATION
At time of delivery, complete operation and maintenance manuals covering the apparatus will be provided. A permanent plate will be mounted in the driver's compartment specifying the quantity and type of fluids required including engine oil, engine coolant, transmission, pump transmission lubrication, pump primer and drive axle.

SAFETY VIDEO
At the time of delivery Pierce will also provide one (
1 )
39 -minute, professionally-produced
apparatus safety video, in DVD format. This video will address key safety considerations for personnel to follow when they are driving, operating, and maintaining the apparatus, including the 5/24/2022
Customer:

City of Sacramento Fire
Department
Bid Number:
771
Representative
Hansen, Brad
Job Number:

Requirements Manager:

Organization:

Golden State Fire Apparatus, Inc
Description:

FX3 Wildland, International, 100
Chassis:

International HV, 4x4, Wildland BX3
Body:

WILDLAND BX3, Type 3, NFPA 1906
1 771
Bid #:

following: vehicle pre-trip inspection, chassis operation, pump operation, and safety during maintenance.

PERFORMANCE TESTS
A road test will be conducted with the apparatus fully loaded and a continuous run of no less than ten (
10 ) miles. During that time the apparatus will show no loss of power nor will it overheat. The transmission drive shaft or shafts and the axles will run quietly and be free of abnormal vibration or noise. The apparatus will meet NFPA
1906
acceleration requirements and NFPA
1906
braking
requirements. The apparatus when fully loaded will not have less than 25 percent nor more than
50 percent on the front axle and not less than
50 percent nor more than
75 percent on the rear
axle.

SERVICE AND WARRANTY SUPPORT
Pierce dealership support will be provided by
Golden State Emergency Vehicles Inc
by
operating

a Pierce authorized service center. The service center will have factory-trained mechanics on staff versed in Pierce fire apparatus. The service facility will be located within twenty five (
25 )
miles
of the fire department.

In addition to the dealership, Pierce has service facilities located in both, Weyauwega, Wisconsin and Bradenton, Florida. Pierce also maintains a dedicated parts facility of over 100,000
square
feet in Appleton, Wisconsin. The parts facility stocks in excess of $5,000,000
in parts dedicated to
service and replacement parts. The parts facility employs a staff dedicated solely for the distribution and shipment of service and replacement parts.

Service parts for the apparatus being proposed can be found via Pierceparts.com which, is an interactive online tool that delivers information regarding your specific apparatus as well as the opportunity to register for training classes.

As a Pierce customer you have the ability to view the complete bill of materials for your specific apparatus, including assembly drawings, piece part drawings, and beneficial parts notations. You will also have the ability to search the complete Pierce item master through a parts search function which offers all Pierce SKU's and descriptions offered on all Pierce apparatus. Published component catalogs, which include proprietary systems along with an extensive operators manual library is available for easy reference.

Pierce Manufacturing maintains a dedicated service and warranty staff of over 35 personnel,
dedicated to customer support, which also maintains a
24 hour
7 day a week toll free hot line,
four (
4 ) on staff EVTs, and offers hands-on repair and maintenance training classes multiple times a year.

LIABILITY
The successful bidder will defend any and all suits and assume all liability for the use of any patented process including any device or article forming a part of the apparatus or any appliance furnished under the contract.

INSURANCE PROVIDED BY BIDDER

COMMERCIAL GENERAL LIABILITY INSURANCE
The successful bidder will, during the performance of the contract and for three ( 3 )
years following acceptance of the product, keep in force at least the following minimum limits of commercial general liability insurance:

Each Occurrence
$1,000,000
Products/Completed Operations Aggregate
$1,000,000
Personal and Advertising Injury
$1,000,000
General Aggregate
$2,000,000
Coverage will be written on a Commercial General Liability form. The policy will be written on an occurrence form and will include Contractual Liability coverage for bodily injury and property damage subject to the terms and conditions of the policy.

The policy will include Owner as an additional insured when required by written contract.

COMMERCIAL AUTOMOBILE LIABILITY INSURANCE
The successful bidder will, during the performance of the contract, keep in force at least the following minimum limits of commercial automobile liability insurance and coverage will be written on a Commercial Automobile liability form:

Each Accident Combined Single Limit:
$1,000,000

UMBRELLA/EXCESS LIABILITY INSURANCE
The successful bidder will, during the performance of the contract and for three ( 3 )
years following acceptance of the product, keep in force at least the following minimum limits of umbrella liability insurance:

Aggregate:
$3,000,000
Each Occurrence:
$3,000,000
The umbrella policy will be written on an occurrence basis and at a minimum provide excess to the bidder's General Liability and Automobile Liability policies.

The required limits can be provided by one (
1 ) or more policies provided all other
insurance requirements are met.

Coverage will be provided by a carrier(s) rated A- or better by A.M. Best.

All policies will provide a
30 -day notice of cancellation to the named insured. The Certificate of Insurance will provide the following cancellation clause: Should any of the above described polices be cancelled before the expiration date thereof, notice will be delivered in accordance with the policy provisions.

Bidder agrees to furnish owner with a current Certificate of Insurance with the coverages listed above along with the bid. The certificate will show the purchaser as certificate holder.

INSURANCE PROVIDED BY MANUFACTURER

PRODUCT LIABILITY INSURANCE
The manufacturer will, during the performance of the contract and for three ( 3 ) years
following acceptance of the product, keep in force at least the following minimum limits of Product Liability insurance:

Each Occurrence
$1,000,000
Products/Completed Operations Aggregate
$1,000,000
Coverage will be written on a Commercial General Liability form. The policy will be written on an occurrence form. The manufacturer's policy will include the owner as additional insured when required by written contract between the Owner and a 2 771
Bid #:

Pierce authorized dealer.

UMBRELLA/EXCESS LIABILITY INSURANCE
The manufacturer will, during the performance of the contract and for three ( 3 ) years
following acceptance of the product, keep in force at least the following minimum limits of umbrella liability insurance:

Each Occurrence:
$25,000,000
Aggregate:
$25,000,000
The umbrella policy will be written on an occurrence basis and provide excess to the manufacturer's General Liability/Products policies.

The required limits can be provided by one (
1 ) or more policies provided all other
insurance requirements are met.

Coverage will be provided by a carrier(s) rated A- or better by A.M. Best.

Manufacturer agrees to furnish owner with a current Certificate of Insurance with the coverages listed above along with the bid. The certificate will show the purchaser as the certificate holder.
0018257
Commercial chassis & Snorkel
products
0584455
Manufacture Location, Bradenton,
Florida
Your apparatus will be manufactured in Bradenton, Florida. 0584453
RFP Location: Bradenton, Florida

0588609
Vehicle Destination, US

0028079
Match Not Required

0799089
Comply NFPA 1906 Changes Effect
Jan 1 , 2016 with Exceptions,
Commercial Chassis
NFPA
2016

STANDARDS
This apparatus specification includes a commercial chassis that has not been certified to meet all the requirements of NFPA
1906
by the chassis manufacturer. Although this chassis may comply with certain aspects of the standard, certification has not been received from this chassis manufacturer that all criteria have been met. The body and equipment as built by Pierce will comply with the current NFPA
1906
standards effective January
2016
, except as noted on the
NFPA exceptions list.

Certification of slip resistance of all stepping, standing and walking surfaces must be supplied with delivery of the apparatus.

A plate that is highly visible to the driver while seated will be provided. This plate will show the overall height, length, and gross vehicle weight rating.

The manufacturer will have programs in place for training, proficiency testing and performance for any staff involved with certifications.

An official of the company will designate, in writing, who is qualified to witness and certify test results.
0547534
1906 Wildland Fire Apparatus

0588619
Not Required, Vehicle Certification

0511675
Certification, Pump, Wildland

PUMP TEST
The pump will be tested and certified by the apparatus manufacturer. The test results along with the pump manufacturer's certification of hydrostatic test, the engine manufacturer's certified brake horse power curve and the manufacturer's record of pump construction details will be forwarded to the Fire Department.
3 771
Bid #:

0000000
STF
GSFA, Final Insp, Florida Factory,
Major Airport, 3 Days and 2 nights

FINAL INSPECTION FACTORY TRIP
A final inspection trip to the manufacturing facility will be provided for three (
3 )
Customer
representative(s). The intent of this trip is to ensure that the apparatus is built to specification and to detect any deficiencies that require correction. The final inspection trip will have a duration of three (
3 ) days and two (
2 ) nights and be scheduled at times mutually agreed upon between Golden State Fire Apparatus (GSFA). and the Customer. Costs for airfare, lodging, meals and ground transportation while at the manufacturers location will be the responsibility of GSFA. Air travel will be from one of the following airports: Sacramento, San Francisco or San Jose.

Costs such as Customer ground transportation in California, Customer airport parking, Customer luggage fees and Customer incidentals while traveling to the factory will be the responsibility of the Customer. Flight reservations are non-refundable and in the event of a cancellation after booking, the Customer will be responsible for all costs associated with this cancellation, which may include not only the original ticket cost but also any change or cancellation fees imposed by the airline and/ or travel agency. Flight reservations are also non-transferable. 0799172

FLEET CUSTOMER

0766110
Consortium, Sourcewell

0537375
Unit of Measure, US Gallons

0030006
Bid Bond Not Requested

BID BOND NOT REQUESTED
A bid bond will not be included. If requested, the following will apply:

All bidders will provide a bid bond as security for the bid in the form of a 5%
bid bond to
accompany their bid. This bid bond will be issued by a Surety Company who is listed on the U.S.

Treasury Departments list of acceptable sureties as published in Department Circular 570
. The
bid bond will be issued by an authorized representative of the Surety Company and will be accompanied by a certified power of attorney dated on or before the date of bid. The bid bond will include language, which assures that the bidder/principal will give a bond or bonds as may be specified in the bidding or contract documents, with good and sufficient surety for the faithful performance of the contract, including the Basic One (
1 ) Year Limited Warranty, and for the
prompt payment of labor and material furnished in the prosecution of the contract.

Notwithstanding any document or assertion to the contrary, any surety bond related to the sale of a vehicle will apply only to the Basic One (
1 ) Year Limited Warranty for such vehicle. Any surety
bond related to the sale of a vehicle will not apply to any other warranties that are included within this bid (OEM or otherwise) or to the warranties (if any) of any third party of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. In the event of any contradiction or inconsistency between this provision and any other document or assertion, this provision will prevail.
0582800
Performance Bond, 100% with 25%
Warranty Bond, 1 Yr, and Payment
Bond

PERFORMANCE BOND,
1 YEAR
The successful bidder will furnish a Performance and Payment bond (Bond) equal to 100
percent
of the total contract amount within
30 days of the notice of award. Such Bond will be in a form acceptable to the Owner and issued by a surety company included within the Department of Treasury's Listing of Approved Sureties (Department Circular 570
) with a minimum A.M. Best
Financial Strength Rating of A and Size Category of XV. In the event of a bond issued by a surety of a lesser Size Category, a minimum Financial Strength rating of A+ is required.

Bidder and Bidder's surety agree that the Bond issued hereunder, whether expressly stated or not, also includes the surety's guarantee of the vehicle manufacturer's Basic One ( 1 ) Year Limited
Warranty period included within this proposal. Owner agrees that the penal amount of this bond will be simultaneously amended to
25 percent of the total contract amount upon satisfactory acceptance and delivery of the vehicle(s) included herein. Notwithstanding anything contained within this contract to the contrary, the surety's liability for any warranties of any type will not exceed one (
1 ) year from the date of such satisfactory acceptance and delivery, or the actual Basic One (
1 ) Year Limited Warranty period, whichever is shorter. 0010007
No Approval Drawing Req'd.

0589819
Electrical Diagrams, Commercial

ELECTRICAL WIRING DIAGRAMS
Two (
2 ) electrical wiring diagrams, prepared for the body as it interfaces with the commercial chassis, will be provided.
0768801
International HV, 4x4, Wildland BX3

CHASSIS
The chassis will be an International, HV supplied with the following equipment:
0893566
Model Year 2024

0765496
SP
Use SF-3203 IHC Chassis Spec
(Wildland BX3) [Use Also w/3204]
4 771
Bid #:

0891187
Base Price, International HV, 4x4
Wildland BX3, Effective 02/01/2022

0761935
Overall Height, Wildland BX3 -
w/International Chassis - 10' 2"

MAXIMUM OVERALL HEIGHT
The maximum overall height of the apparatus will be no more than 122.00
" (
10 '
2 ").
0751233
Angle of Approach,Approximately 28
Degrees, International / Wildland BX3

ANGLE OF APPROACH
The angle of approach will be about
28 degrees. This will be effective with the truck in a
loaded

state.
0767548
Angle of Departure, Approximately 25
Degrees, Wildland BX3

ANGLE OF DEPARTURE
The angle of departure will be about
25 degrees. This will be effective with the truck in a
loaded

state.
0764212
Wheelbase, 183", International, 4x4,
Wildland BX3

WHEELBASE
The wheelbase of the vehicle will be
183.00
".
0760045
GVW Rating, 36,000#, Commercial
Chassis

GVW RATING
The gross vehicle weight rating will be
36,000
pounds.
0027644
Frame, Chassis, International

FRAME
The frame rails will be formed from
120,000
psi yield, heat treated alloy steel.
0686546
Frame Reinforcement, International
HV 4x4, "C" Channel

FRAME LINER
An outer "C" channel frame liner constructed of heat treated alloy steel will be provided. 0742184
Axle,Front,13K Rating,International
HV 4x4 w/o Transfer Case PTO, BX3

FRONT AXLE
The front drive axle will have a ground rating capacity of 13,000
lb.

TRANSFER CASE
The transfer case will be a two (
2 ) speed with high and low range.

Electric over air shift controls will be provided.
0770176
Suspension, Front Spring, 14,000 lb,
Commercial

FRONT SUSPENSION
Spring mounted: Parabolic, Taper Leaf
Capacity at ground:
14,000
lb
0073051
Shock Absorbers, Front

Shock absorbers will be provided on the front axle.
0789186
Brakes, Cam Front, 16.50"x 5.00"
Commercial

FRONT BRAKES
The front brakes will be S-Cam,

16.50 " x

5.00 ". The front brakes will be provided with automatic slack adjusters.
0585779
Goodyear Tires

TIRE BRAND
The default brand of tire for the commercial chassis manufacturer for this apparatus is Goodyear.

However, the commercial chassis manufacturer reserves the right to substitute brands and models of tire as may be available at the factory on the date of manufacture. They will provide the proper tread style and weight rating for the position in which the tire is installed.

Pierce Manufacturing and the chassis manufacturer are working to provide the brand of tire specified. However, due to shortages (and even model changes by the tire manufacturers), if the chassis manufacturer substitutes other tires, they will not be changed by Pierce. 0772242
Tires, Front, 22.50, Traction Tread,
4x4 (to 14.6k GAWR)

TIRES, FRONT
Front tires will be

22.50 , radial tires with a traction tread pattern suitable for the steering axle position on a front driving axle. The capacity of the tires will meet or exceed the rating of the axle and/or suspension and a maximum top speed per the requirements described elsewhere in this proposal, up to
75 MPH.
0683147
Wheel, Steel, 22.50", 4x4

WHEELS, FRONT
Wheels for the front axle will be

22.50 " steel disc, properly sized for the provided tires. 5 771
Bid #:

0764156
Axle, Rear, Meritor, 23K Rating,
International HV 4x4, BX3 Wildland

REAR AXLE
The rear axle will have a ground rating capacity of
23,000
lb.

PARKING BRAKE
The parking brake will be spring set and located on the rear axle service brake. 0772020
S-Cam Style 16.50" x 7.00"

Rear axle brakes will be 16.50" x 7.00", S-Cam drum type brakes. Automatic slack adjusters will be provided.
0767494
Top Speed of Vehicle, Comply
w/NFPA, Wildland BX3

REAR AXLE RATIO
NFPA
1906
,
2016
edition, section

4.15.2 requires that the maximum top speed of fire apparatus with a GVWR over
33,000
lb will not exceed either
68 mph or the manufacturer's maximum fire
service speed rating for the tires installed on the apparatus, whichever is lower.

The top speed of the apparatus as manufactured meets the NFPA requirement of a top speed of 68 miles per hour.

The rear axle
ratio
provided will to allow the vehicle to reach an approximate top speed of 73 miles per hour, but the speed of the chassis will be electronically limited 68 MPH
.
0621638
Suspension, Rear Spring, 23,500 lb
w/4500 lb Steel Leaf Aux. IHC

REAR SUSPENSION
The rear suspension shall be Vari-Rate multi-leaf spring suspension with a capacity at ground of 23,500
lbs.

Auxiliary steel leaf spring suspension with a capacity of 4500
lbs. will be included.
0607123
Differential Lock, Automatic,
International HV 4x4

LOCKING DIFFERENTIAL
The rear axle will be equipped with a driver controlled differential lock. 0772235
Tires, Rear, 22.50, Traction Tread,
4x4 (to 27k GAWR)

TIRES, REAR,
4 X
4 Rear tires will be

22.50 , radial tires with a traction tread pattern suitable for the rear axle position on an all-wheel-drive vehicle. The tire capacity will meet or exceed the capacity of the axle and/or suspension. Tires will be rated for a maximum top speed per the requirements described elsewhere in this proposal, up to
75 MPH
Due to ratio matching requirements of an all-wheel-drive vehicle, the front and rear tire sizes will be the same. The size of the tires provided will be at least the minimum size required to meet the GAWR rating of both axles.
0683146
Wheel, Steel, 22.50", 4x4

WHEELS, REAR
The rear wheels will be

22.50 " steel disc properly sized for the provided tires. 0767493
No Tire Pressure Indicator, Fire
Department Omits, Non-NFPA 1906-
2016 Compliant

TIRE PRESSURE INDICATOR
NFPA
1906
,
2016
edition, section

4.13.4 requires each tire be equipped with a visual indicator or monitoring system that indicates tire pressure.

Per Fire Department specification, a tire pressure indicator is not on the apparatus as manufactured. This apparatus will be non-compliant to NFPA 1906
standards effective at time of
contract execution.
0012045
Mud Flap, Rear, Pierce Logo

MUD FLAPS
Mud flaps with a Pierce logo will be installed behind the rear wheels. 0740599
Chocks, Wheel, Worden HWG- SB,
Super Gripper, BX3

WHEEL CHOCKS
There will be
one (
1 ) pair
of Worden Safety Products, Model HWG-SB, wheel chocks provided.

Heavy Duty, large molded aluminum wheel chock with solid bottom, natural cast aluminum finish. 0765485
Mounting Brackets, Chocks, Worden
Safety, Model U815T, BX3, BX

WHEEL CHOCK BRACKETS
There shall be
one (
1 ) pair
of Worden Safety model U
815
T mounting wheel chock brackets
provided . The brackets shall be mounted
below the left side rear compartment and below the
right side rear compartment
.
0020881
ABS, Anti-Lock Braking System,
Commercial

ANTI-LOCK BRAKE SYSTEM
The vehicle will be equipped with an anti-lock braking system. The ABS will provide anti-lock braking control on both the front and rear wheels. It will be a digitally controlled system that utilizes microprocessor technology to control the anti-lock braking system. Each wheel will be monitored by the system. When any particular wheel begins to lockup, a signal will be sent to the control unit. This control unit then will reduce the braking of that wheel for a fraction of a second and then reapply the brake. This anti-lock brake system will eliminate the lockup of any wheel thus helping to prevent the apparatus from skidding out of control. 0009547
Air Compressor, Brake, 18.7 CFM,
Commercial

AIR COMPRESSOR, BRAKE SYSTEM
The air compressor will have an output of

18.7 cubic feet per minute.
6 771
Bid #:

0773985
Air Dryer, Brake, w/Heater,
Commercial

AIR DRYER
An air dryer with a heater will be provided. Other features of this air dryer include:
- Desiccant style filter
- In-line filtration system
- Automatic purge valve
0020851
Not Required, Air Inlet

0752599
SP
Outlet, Air, w/Shut Off Valve, BX

AIR OUTLET
One (
1 ) air outlet
will be installed with a female coupling and shut off valve, located on the driver
side pump panel
. This system will tie into the "wet" tank of the brake system and include an 85 -
psi pressure protection valve in the outlet line to prevent the brake system from losing all air.

A mating male fitting will be provided with the loose equipment. 0728924
Engine, Cummins L9, 360 hp, IHC
HV, BX3
ENGINE
Model: Electronic Cummins L
9-360

Number of Cylinders: Six (
6 )
Displacement:

8.9 L
Rated Brake Horsepower:
360
at
2200
rpm
Peak Torque:
1150
at
1200
rpm
Governed rpm:
2200

VGT Turbocharger
Fuel System: High pressure common rail (HPCR)

ENGINE ACCESSORIES
Fan Clutch: Electric
2 -speed with nylon fan
Air Cleaner: Dry type, with restriction indicator in cab In-tank Oil Cooler
Oil Fill and Level Gauge
Starting Motor:
12 -volt

RADIATOR
Pressurized System, Cross Flow
De-aeration Tank
Anti-Freeze Protection -
40 Degrees Fahrenheit
0001247
High Idle w/Electronic Engine,
Commercial

HIGH IDLE
A high idle switch will be provided on the instrument panel inside the cab. Activating the switch will cause the vehicle to automatically maintain a preset engine rpm.

The high idle switch will be operational only when the parking brake is on and the truck transmission is in neutral. A green indicator light will be provided adjacent to the switch. The light will be labeled "OK To Engage High Idle."
0773963
Auxiliary Brake, Exhaust Brake , VGT
Style, Commercial

ENGINE EXHAUST BRAKE
An exhaust brake with an integral variable geometry turbo charger (VGT) will be provided. The control will be located on the instrument panel within easy reach of the driver. 0120374
Cruise Control, Commercial

ELECTRONIC CRUISE CONTROL
The chassis will be provided with OEM factory installed electronic cruise control. 0725601
Fuel/Water Separator, Racor,
Heated, International, BX3

HEATED FUEL/WATER SEPARATOR
A Racor
400
series fuel/water separator will be provided on the chassis. It will have a 12 VDC
electric heater, and include a primer pump, pre-heater and a water-in-fuel sensor. 0773981
Air Intake, Engine, w/Ember
Separator, OEM Installed,
Commercial
AIR INTAKE, w/EMBER SEPARATOR
The air inlet will be equipped with a stainless steel mesh to separate water and burning embers from the air intake system such that particulate matter larger than

0.039
" (

1.0 mm) in diameter
cannot reach the air filter element.

This will comply with NFPA
1901
and
1906
standards.
0747960
Exhaust,Horiz,RH Step Mtd
DPF/SCR,w/Modification Next
toTransfer Case, 4x4 IHC

EXHAUST SYSTEM
The exhaust system will include a diesel particulate filter (DPF) and a selective catalytic reduction (SCR) device to meet current EPA standards. The DPF and SCR will be mounted horizontally outside of the frame rails in the right side front step area.

The exhaust piping will include a special OEM routing closer to the transfer case that allows extra under cab space.
7 771
Bid #:

0684987
Exhaust Modifications, Commercial
Chassis, Horizontal Exhaust

EXHAUST MODIFICATIONS
The exhaust will terminate with a horizontal tailpipe and diffuser ahead of the right side rear wheels.

A heat deflector shield will be provided where the tail pipe is routed under any side compartmentation.

All modifications will be approved by the chassis engine manufacturer and/or the chassis OEM.

Exhaust treatment devices will not be altered.
0674092
Exhaust, Modified for Plymovent
System, (Shipped Loose)
Commercial

EXHAUST MODIFICATION
The exhaust pipe will be brought out from under the body at a 90 degree angle from the truck.

The chassis manufacturer's diffuser and tail pipe will extend a minimum of

2.00 " past the body,
adaptable for the Plymovent system. There will be a clearance of

4.00 " completely around the
pipe once past the side of the body. A Pierce style diffuser with stop will be provided and shipped loose with the truck for the customer to install. The stop will prevent the PlymoVent nozzle from sliding too far on.
0071090
Coolant Hoses, Rubber - Commercial
Chassis

COOLANT LINES
Premium rubber hose will be used for all engine coolant lines installed by Pierce Manufacturing.

Hose clamps will be the constant torque type to prevent coolant leakage. They will expand and contract according to coolant system temperature thereby keeping a constant clamping pressure on the hose.
0773634
Fuel Tank, 70 Gallon, Left Side,
Aluminum, Commercial

FUEL TANK
A
70 gallon fuel tank will be provided and mounted at the left-hand cab step. The tank will be constructed of aluminum.
0773952
DEF Tank, Left Side Location,
Commercial

DIESEL EXHAUST FLUID TANK
A diesel exhaust fluid (DEF) tank will be provided and mounted on the left side, below the cab.

The tank will be sized by the chassis manufacturer based on the engine provided. It will include an integrated heater unit that utilizes engine coolant to thaw the DEF in the event of freezing. 0723716
Fuel Priming Pump, Electronic,
Automatic, Cummins, No Swt Req'd

FUEL PRIMING PUMP
A Cummins automatic electronic fuel priming pump will be integrated as part of the engine. 0552712
Not Required, Shutoff Valve, Fuel
Line
0696186
Cooler, Chassis Fuel, Commercial,
Provided by Chassis OEM

COOLER, CHASSIS FUEL
A fuel cooler will be provided by the chassis manufacturer. 0764176
Chassis Fuel Line Protection, Fire
Wrap Lagging, Wildland

FUEL LINE PROTECTION
The fuel hoses that run from the chassis fuel tank to the fuel pump will be wrapped with fire wrap lagging to protect them from heat damage. The lagging will be able to withstand high temperatures and will be secured with stainless steel or fire proof ties. 0051290
Label, "Diesel Fuel Only"

LABEL, FUEL DOOR
A label will be provided,
near the fuel fill location
, to read "Diesel Fuel Only".
0773950
Trans, Automatic, Allison 3000 EVS,
w/(2) PTO Provsions, Commercial

TRANSMISSION
An Allison, model
3000
EVS, electronic torque converting automatic transmission will be provided. To qualify for the EVS rating, the transmission will be filled with synthetic transmission fluid.

Two (
2 ) PTO openings will be located on left and right side of the converter housing (positions 8 o'clock and
4 o'clock).

A transmission temperature gauge or warning light will be installed on cab instrument panel. 0771219
Transmission,Stalk Shifter, Column
Mounted, 5 Speed, International

TRANSMISSION SHIFT CONTROL
A column mounted stalk shifter will be provided. It will electronically control the gear selection in either a manual or automatic mode.

The transmission will be a five (
5 )-speed.
0011475
Transmission Oil Cooler, Internal,
Commercial

TRANSMISSION COOLER
A transmission oil cooler will be provided in a tank of the radiator. 0628385
SP
Reprogram Trans, Downshift To 2nd
With Aux Brake, By Pierce, Allison
Trans

TRANSMISSION SHIFTER CHANGE
The apparatus manufacturer will have the transmission reprogrammed to downshift to 2 nd when
engine brake is applied.
8 771
Bid #:

0527500
Transfer Case Oil Cooler, 4x4,
Commercial

TRANSFER CASE OIL COOLER
The
4 x
4 transfer case will have an oil cooler specifically designed and installed for the application.
0733744
Driveline for PTO/Transfer Case or
No Pump Installation - Commercial

DRIVELINE
Drivelines will be a heavy duty metal tube equipped with universal joints properly sized for the application. A splined slip joint will be provided in each driveshaft. 0762367
Driveline Pre-Approved, International
HV 4x4, Wildland BX3
0692499
Steering, Power, w/Tilt Column,
Commercial Chassis

STEERING
Steering shall consist of an hydraulically driven power steering system with a capacity designed for the axle rating.

For additional comfort, the steering wheel column shall have a tilt feature. 0607536
Skid Plate and Brush Guard, For Fuel
and DEF Tanks, Commercial Chassis

SKID PLATE AND BRUSH GUARD
A
12 gauge removable steel skid plate will be fastened to the bottom side of the fuel tank hangers. The plate will be formed to protect the underside of the plastic DEF tank and will be fastened to the factory chassis steps.
0761934
Chassis Air Line Protection, Fire
Wrap Lagging, Wildland

AIR LINE PROTECTION
All air lines that are routed below the frame rails shall be wrapped with fire wrap lagging to protect them from heat damage. The lagging shall be able to withstand high temperatures and shall be secured with stainless steel or fire proof ties.
0759063
Receiver for Hose Roller
Mounts,Front (Right) & Rear, No
Wiring, BX3

RECEIVERS
Two (
2 ) receivers for the mounting of a removable hose roller will be provided. One will be mounted on the bottom side of the front bumper on the
right side
and one at the rear, under the
rear compartment toward the
right side
.

These receivers will never be used in conjunction with a portable winch, trailer hitch or other use.

A tag indicating that the use is only for the "removable hose roller" will be provided. No electrical connections of any type will be required.
0727421
SP
Winch, Warn, 15000 lb. Fixed, Front,
Steel Cable, Polished Fairlead, BX3

FRONT WINCH
A Warn Series
15 ,
15,000
lb electric winch will nest below the top aluminum treadplate surface of the front bumper. A

28.00 " x

10.00 " door will be provided for maintenance and access to the winch
Direction control lever and remote control plug will be provided. The cover will be provided with a mechanical stay arm
hold open device.

Winch will be mounted on a surface that will not flex when the winch is in use, since it could bind working parts of the winch.

Winch will be braced by a three (
3 ) point mount, as recommended by the winch manufacturer.

Winch will have
70 feet of .
50 " steel cable with hook, pre spooled on drum.

Winch will have planetary gearing. Electric motor will have a thermal overload protection switch.

Wire cables to battery will be two (
2 ) gauge or larger. Speed and amperage draw of winch will be variable depending on winch load.

Winch will have a minimum of a
30 foot remote control cable.

A polished fairlead for use with steel cable will be supplied of sufficient strength to accommodate the winch capacity.

A label will be placed on or near the mount that states the maximum winch load rating and the maximum rope load rating that the mount can support.
0751239
Bumper Extension, 19", Steel
Painted, Chicago Style, Commercial
Chassis, BX3
BUMPER
A one (
1 ) piece bumper manufactured from

0.19 " formed steel with a

0.38 " bend radius will be
provided. The bumper will be a minimum of

10.00 " high with a

1.50 " top and bottom flange, and
will extend

19.00 " from the face of the cab. The bumper will have
45 degree corners. The
bumper will be metal finished and painted job color.

To provide adequate support strength, the bumper will be mounted directly to the front of the C channel frame. The frame will be a bolted modular extension frame constructed of 50,000
psi
tensile steel.

GRAVEL PAN
A gravel pan, constructed of bright aluminum treadplate, will be furnished between the bumper and the cab face and front wheel wells. The pan will be properly supported from the underside to prevent flexing and vibration.
0751237
Tray, (1) Hose Left Side of 19"
Bumper, Wildland BX3

LEFT SIDE HOSE TRAY
A hose tray will be placed in the left side of the extended bumper.

The tray will have a capacity of
75 ' of

1.50 " double jacket cotton-polyester hose
.

Black rubber grating
will be provided at the bottom of the tray. Drain holes will be provided. 9 771
Bid #:

0766331
Cover, Aluminum Treadplate, One (1)
D-Ring Latch, Hose Tray, Notched,
BX3
Left Side Hose Tray Cover
A bright aluminum treadplate cover will be provided over the left side hose tray.

The cover will be notched to allow the hose to be pre-connected to the hose connection.

The cover will be attached with a stainless steel hinge.

There will be one (
1 ) D-ring latch provided to secure the cover in the closed position and a mechanical stay arm
will hold the cover in the open position.
0751236
Tray, (1) Hose Right Side of 19"
Bumper, Wildland BX3

RIGHT SIDE HOSE TRAY
A hose tray will be placed in the right side of the extended bumper.

The tray will have a capacity of
75 ' of

1.50 " double jacket cotton-polyester hose
.

Black rubber grating
will be provided at the bottom of the tray. Drain holes will be provided. 0766332
Cover, Aluminum Treadplate, One (1)
D-Ring Latch, Hose Tray, Notched,
BX3
Right Side Hose Tray Cover
A bright aluminum treadplate cover will be provided over the right side hose tray.

The cover will be "notched" allowing the hose to be pre connected to hose connection.

The cover will be attached with a stainless steel hinge.

A D-ring latch will secure the cover in the closed position and a mechanical stay arm
will hold the
cover in the open position.
0002283
Tow Hooks, Painted

TOW HOOKS
Two (
2 ) painted steel tow hooks will be installed under the bumper and attached to the front frame members. The tow hooks will be painted to match the chassis frame assembly.

The tow hooks will be designed and positioned to allow up to a 6,000
lb straight horizontal pull in
line with the centerline of the vehicle. The tow hooks will not be used for lifting of the apparatus. 0012300
Bracket, License Plate, Frt Bumper
Non-Illuminated

LICENSE PLATE BRACKET
A non-illuminated license plate bracket will be mounted on the front bumper. The bracket will be formed from bright stainless steel.
0752061
Lights,Off Road Driving,HiViz
LED,Under Bumper,Fwd Facing and
Bumper Corners,BX3

OFF ROAD DRIVING LIGHTS
One (
1 )

20.00 " HiViz light, model FT-MB-
15 -EFT-B with a black housing will be installed under
the center of the front bumper. This light will be forward facing to illuminate the area directly in front of the vehicle. Two thirds of the optics will provide a wide/flat beam pattern and one third of the optics will be spot type to project light further forward.

A pair

9.00 " of HiViz model FT-MB-
6 -E-B lights with a black housing will be installed under the bumper, one each side, at a
45 -degree angle facing outward. All the optics of these lights will provide a wide flat light beam pattern.

The center forward facing light and the pair of corner lights will be controlled by a single switch
in
the cab.
0772084
Standard Hood, SFA, International

HOOD
The hood will be a three-piece Fiberglass construction. It will tilt forward and include splash panel and under hood insulation for sound abatement. Rubber fender extensions will be installed on the wheel openings.
0762462
Cab, 4-door Crew Cab, International
HV, BX3
CAB
Type: Four (
4 ) Door, Conventional (engine forward)
Construction: Welded Steel and Fiberglass
Accessories:
- Tinted Glass in all Windows
- Black Rubber Floormats
- Dual Sun-Visors
-

18.00 " Cab Entrance Handrails -

1.28 " diameter extruded aluminum with rubber inserts one ( 1 )
each side
- Dome Light with Map Light
- Fresh Air Heater and Defroster
- Fiberglass Front End, Three (
3 ) Piece Construction
- Composite Aero Design Halogen Headlights
- Air Ride Cab Suspension
0024223
Cab Interior, IHC, Gray

CAB INTERIOR, IHC, GRAY
Gray Vinyl Upholstery
0582768
Grille, Chromed Plastic, Stationary,
International

CAB GRILLE - STATIONARY
The cab grille will be a chrome plated high impact plastic with a vertical channel design, and will include chrome headlight bezels. The grille will be attached to the radiator core support structure and will not tilt with the hood.
10 771
Bid #:

0762934
Mirrors, Bright Finish Heads, Power
Adjust, Heated, International MV/HV

MIRRORS
Mirrors with

14.10 " x

7.55 " flat rear view with integral convex mirrors will be provided on both sides of the cab. The mirror housings will have a bright finish with integral LED clearance lights.

Both sides will be remote controlled with thermostatically controlled heated glass. 0762227
Step Package, Under Front Cab
Doors, NFPA Compliant, Wildland
BX3

CAB ACCESS STEPS
The cab steps under the front doors will be provided by the chassis manufacturer. These steps will be modified by the apparatus manufacturer as required to meet NFPA step requirements. 0767309
Compartment, Tool, Under RH Crew
Cab, Wildland BX3

COMPARTMENT, STORAGE
A double-door storage compartment will be provided below the right side crew cab door. Both doors will be double pan construction with a D-ring latch and vertical hinges.

The exterior of this compartment will serve as an entrance step to the crew cab.

An LED compartment light will be provided inside the compartment with a magnetic switch. 0767312
Compartment,Tool/Brass, Under LH
Crew Cab, Max Size, BX3

COMPARTMENT, STORAGE
A storage compartment for tools and brass attachments will be provided below the left side crew cab door. There will be a drawer style tray that slides out for access to the equipment.

The exterior of this compartment will serve as an entrance step to the crew cab.

An LED compartment light will be provided inside the compartment with a magnetic switch. 0637488
Lights, Cab & Crw Cab Acs Stps,
LED, 4 Door Cab, BX Product

STEP LIGHTS
There will white LED step lights provided to meet NFPA step lighting requirements. Lights will be installed at each cab and crew cab door step.

The lights will be activated when any cab door is opened. 0517654
Window, Blank Panel, At Rear of
Cab, IHC, Wildland, PMFD

WINDOW, BLANK PANEL
The back wall rear cab window will be removed and replaced with an aluminum tread plate panel.

The smooth side will be painted
600
T gray to match the cab interior color.
0773759
Power Windows & Door Locks, 4-
Door Cab, Commercial

POWER WINDOWS AND LOCKS
The cab doors will have electrically powered windows and locks. 0070598
Daytime Running Lts, Commercial

DAYTIME RUNNING LIGHTS
The chassis will be provided with daytime running lights. 0773943
Air Conditioning, Commercial

AIR CONDITIONING
An air conditioner will be provided that is integral with heater and defroster system. 0759502
Ember Screen, for AC Filter, Air
Intake, International

AIR CONDITIONING EMBER FILTER
An ember filter will be provided by the commercial chassis OEM to keep embers out of the HVAC filter element.
0005940
Lights, Engine Compt, (2)
Commercial Chassis

ENGINE COMPARTMENT LIGHTS
Two (
2 ) engine compartment lights will be installed under the engine hood, of which the switches are an integral part.
0731748
Console, 4-Door, Switches, Radio
and Storage, BX3

CAB CONSOLE
There will be a console located between the front seats with room for radio installation, the electrical and emergency switches, a siren and auxiliary pump controls (if the truck is so equipped).

The area for the siren and electrical and emergency switches will be located toward the front of the console.

The console will be configured such that
the auxiliary pump controls are to be located toward the right side for easier control by the officer
.

It will also be also be designed
without the need to accommodate a turret control joystick .

At the rear of the console will be a storage area
with an open top
.

It will be constructed of smooth aluminum and painted black. 0767593
Seating Capacity, Cab, 4-Door,
Wildland BX3

SEATING CAPACITY
The seating capacity in the cab will be
four (
4 )
.
0762937
Seats, Cab, Air driver w/Air officer -
International MV/HV

SEATING
Seating inside the cab will consist of an air-ride driver seat and an air-ride officer seat. 11 771
Bid #:

0691848
Seats, 2-man, National, Air Ride,
Non-SCBA, Outboard - International
MV/HV
SEATING (crew cab)
Two (
2 ) individual, National
2000
air-suspension, high back non-SCBA style seats shall be provided - one in each outboard seating position.
0758667
Console/EMS, Between Crew Cab
Seats, 30" Tall, Nylon Webbing, BX3

CONSOLE/EMS

COMPARTMENT - CREW CAB
A console/EMS compartment will be provided in the crew cab between the two rear seats.

The compartment will be constructed of smooth aluminum, and painted black. Approximate dimensions of the console/compartment will be

30.00 " high x

20.00 " wide x

24.00 " deep
The front side of the compartment will be open and provided with a heavy black nylon webbing made of
1 " nylon strap with a
2 " box pattern. The nylon webbing will be fastened to the bottom of the opening in a fixed manner. The top of the webbing will be fastened with side release clips and footman loops to retain the contents with the compartment.

A quantity of
one (
1 ) infinitely adjustable shelf with a

0.75 " up-turned lip
will be provided inside the
compartment. It will be constructed from aluminum and vertically adjustable.

COMPARTMENT LIGHT
There will be
one (
1 ) white LED strip light installed on the left side of the compartment opening . It
will be controlled by a rocker switch mounted on the exterior of the compartment.

This storage compartment will be compliant per NFPA standard for automotive fire apparatus.
0551164
Seat Belt Web Length, Commercial
Chassis

SEAT BELT WEB LENGTH
The chassis seat belt web length as supplied by the commercial chassis manufacturer will be compliant to NFPA

14.1.3.2 and

14.1.3.3 .
0584364
Seat Belts, Red, Commercial Chassis

SEAT BELTS
All seating positions in the cab and crew cab (if applicable) will have red seat belts. 0547549
Helmet Storage, Not Required, NFPA
1906 Apparatus
0778548
Light, Map, Federal Littlite, LED,
Gooseneck, BX

MAP LIGHT
There will be
one (
1 )
Federal Littlite® LED map light(s) provided in the cab and located on the officer's side front face of the console. Each map light will have a on/off switch
with a

12.00 "
long
flexible neck.

Each light will be provided with red and white LEDs.

The light switch(es) will be connected
directly to the battery switched power
.
0767583
Portable Hand Light, Not Required,
NFPA 1906 2016 Apparatus

0584358
Cab Instrumentation, Commercial
Chassis

CAB INSTRUMENTS
- Engine Temperature Gauge and Warning Buzzer
- Engine Oil Pressure Gauge and Warning Buzzer
- Speedometer with Odometer
- Engine Tachometer
- Engine Hourmeter
- Fuel Level Gauge
- DEF Level Gauge and Warning Lamp
- Voltmeter: Low voltage red warning light and audible alarm - Air Brake Pressure Gauge
- Air Restriction Indicator
- Circuit Breakers: For overload protection of electric circuits - Ignition Switch: Keyless type
0767575
Panel, Emergency Switch, on
Console, BX3

EMERGENCY SWITCH PANEL
An emergency switch panel will be provided in the cab. The switch panel will be located on the floor mounted console.
0641093
Light, Do not move apparatus,
Commercial, BX Program
"DO NOT MOVE APPARATUS" INDICATOR
A flashing red indicator light (located in the driving compartment) will be illuminated automatically per the current edition of NFPA. The light will be labeled "Do Not Move Apparatus If Light Is On".

The same circuit that activates the Do Not Move Apparatus indicator will not activate any alarm

when the parking brake is released.
0005926
Light, Open Door - Commercial Std

OPEN DOOR INDICATOR LIGHT
A red "open door" indicator light will be provided inside the cab, in clear view of the driver, to warn of an open compartment door.
0072620
Wiper control, intermittent feature
Commercial

WIPER CONTROL
Wiper control will include an intermittent feature and windshield washer controls. 12 771
Bid #:

0756891
SP
Wiring, Spare, 60A 12V DC, 12
Circuit Fuse Block, Blue Sea 5026,
BX3

SPARE CIRCUIT
There will be
one (
1 )
pair of wires, including a positive and a negative, installed on the apparatus.

The above wires will have the following features:

The positive wire will be connected
directly to the battery power
.

The negative wire will be connected to ground.

Wires will be protected to
60 amps at
12 volts DC.

Routing location will be
in the center console
.

Termination will be to a Blue Sea System, model
5026
,
12 circuit with negative bus bar, St Blade
Fuse Block. The terminal block will include a cover with circuit labels.

Wires will be sized to
125%
of the protection.

This circuit(s) may be load managed when the parking brake is set. 0758909
SP
Wiring, Spare, 30 A 12V DC, 6 Circuit
Fuse Block, Blue Sea 5025 1st, BX3

SPARE CIRCUIT
There will be
one (
1 )
pair of wires, including a positive and a negative, installed on the apparatus.

The above wires will have the following features:

The positive wire will be connected
directly to the battery power
.

The negative wire will be connected to ground.

Wires will be protected to
30 amps at
12 volts DC.

Power and ground will terminate
in the center console
.

Termination will be to a Blue Sea System, Model
5025
,
6 circuit with negative bus bar. The
terminal block will include a cover with circuit labels.

Wires will be sized to
125%
of the protection.

This circuit(s) may be load managed when the parking brake is set. 0748987
SP
Wiring, Spare, 20 A 12V DC 1st, BX3

SPARE CIRCUIT
There will be
one (
1 )
pair of wires, including a positive and a negative, installed on the apparatus.

The above wires will have the following features:

The positive wire will be connected
directly to the battery power
.

The negative wire will be connected to ground.

Wires will be protected to
15 amps at
12 volts DC.

Power and ground will terminate
RS over rear axle compartment
.

Termination will be
with
15 amp, power point plug with rubber cover
.

Wires will be sized to
125%
of the protection.

This circuit(s) may be load managed when the parking brake is set. 0748995
SP
Wiring, Spare, 4.8 A 12V DC, USB
Termination Blue Sea 1045 1st, BX3

SPARE CIRCUIT
There will be
two (
2 )
dual USB fast charge socket mounts installed on the apparatus.

The above wires will have the following features:

The positive wire will be connected
directly to the battery power
.

The negative wire will be connected to ground.

Wires will be protected to

4.8 amps at
12 volts DC.

The USB socket mount will be
on the top front of the center cab console (
1 ) per side, match
#37008
.

Termination will be a Blue Sea Systems part number
1045
dual USB charger socket.

Wires will be sized to
125%
of the protection.

This circuit(s) may be load managed when the parking brake is applied. 0759671
Wiring,Spare,4.8 A 12V DC,USB
Termination Blue Sea 1045, on Rear
of Console, BX3

SPARE CIRCUIT
There will be
two (
2 )
dual USB fast charge socket mounts installed in the cab of the apparatus.

The above wires will have the following features:

The positive wire will be connected
directly to the battery power
.

The negative wire will be connected to ground.

Wires will be protected to

4.8 amps at
12 volts DC.

The USB socket mount will be installed on the rear of the center cab console.

Termination will be a Blue Sea Systems part number
1045
dual USB charger socket.

Wires will be sized to
125%
of the protection.

This circuit(s) may be load managed when the parking brake is applied. 0762221
Auxiliary Power Outlet (12V) and
USB Port, Commercial Chassis

12 V POWER OUTLET AND USB PORT
A
12 -volt auxiliary power output and a USB port will be provided by the chassis manufacturer.

They will be located in the instrument panel.
0762644
Radio, AM/FM Stereo, w/Weather
Band & Clock, International, BX3
RADIO
A digital electronic tuning AM/FM stereo with a weather band and clock will be provided. The speakers will be
the standard speakers provided with the AM/FM radio system .
0622928
Not Available, Vehicle Information
Center, Multiplex System,
Commercial Chassis
0734854
Collision Mitigation, Not Requested

13 771
Bid #:

0606231
Not Required, Vehicle Data Recorder
and Seat Belt Monitor,
1906/Export/ULC
0763435
Two-Way Radio Accommodation
Package - Wildland/BX3

TWO-WAY RADIO ACCOMMODATION PACKAGE
One set of
12 volt wire leads will be provided for the future installation of a two-way radio. These leads will consist of one (
1 )
30 -amp battery direct circuit, one (
1 )
10 -amp battery switched circuit
and one (
1 ) ground circuit. These leads will be
3 ' long and terminate inside the console with heat
shrink caps.

One (
1 ) NMO mobile radio antenna mount with RG-
58 A/U stranded coaxial cable will be
provided. The antenna mount will be installed through the cab roof, and the coaxial cable will be routed to inside the center console. All wiring will be neatly coiled and clearly marked.

A weatherproof cap for the antenna mount will also be installed. 0758911
SP
Two-Way Radio Accommodation
Package - Additional, BX3

TWO-WAY RADIO ACCOMMODATION PACKAGE
An additional set of
12 volt wire leads will be provided for the future installation of a two-way radio. These leads will consist of one (
1 )
30 -amp battery direct circuit, one (
1 )
10 -amp battery
switched circuit and one (
1 ) ground circuit. These leads will be
3 ' long and terminate inside the
console with heat shrink caps.

A weatherproof cap for the antenna mount will also be installed. 0767278
Camera w/Guard, Pierce, 7" LCD,
Rear Camera Only, BX

VEHICLE CAMERA SYSTEM
There will be a color vehicle camera system provided with the following:

One (
1 ) camera located at the rear of the apparatus, pointing rearward, displayed automatically with the vehicle in reverse
The camera image will be displayed on a

7.00 " LCD display located
centered overhead between
the sun visors
. The display will include manual camera activation capability and audio from the active camera.

The following components will be included:

One (
1 ) MO
700136
DC Display
One (
1 ) SV-CW
134639
CAI Camera
All necessary cables
Aluminum treadplate guard to protect camera from damage 0612323
Weldon V-MUX, Electrical System,
International Chassis, BX3
0770583
Electrical System, International HV,
Wildland BX3

ELECTRICAL
All
12 -volt electrical equipment installed by the apparatus manufacturer will conform to modern automotive practices. All wiring will be high temperature crosslink type. Wiring will be run in loom or conduit where exposed and have grommets where wire passes through sheet metal.

Automatic reset circuit breakers will be provided which conform to SAE Standards. Wiring will be color, function and number coded. Function and number codes will be continuously imprinted on all wiring harness conductors at

2.00 " intervals. Exterior exposed wire connectors will be positive locking, and environmentally sealed to withstand elements such as temperature extremes, moisture and automotive fluids. Electrical wiring and equipment will be installed utilizing the following guidelines:
(
1 ) All holes made in the roof will be caulked with silicon. Rope caulk is not acceptable. Large fender washers, liberally caulked, will be used when fastening equipment to the underside of the cab roof.
(
2 ) Any electrical component that is installed in an exposed area will be mounted in a manner that will not allow moisture to accumulate in it. Exposed area will be defined as any location outside of the cab or body.
(
3 ) Electrical components designed to be removed for maintenance will not be fastened with nuts and bolts. Metal screws will be used in mounting these devices. Also a coil of wire will be provided behind the appliance to allow them to be pulled away from mounting area for inspection and service work.
(
4 ) Corrosion preventative compound will be applied to all terminal plugs located outside of the cab or body. All non-waterproof connections will require this compound in the plug to prevent corrosion and for easy separation (of the plug).
(
5 ) All lights that have their sockets in a weather exposed area will have corrosion preventative compound added to the socket terminal area.
(
6 ) All electrical terminals in exposed areas will have silicon ( 1890
) applied completely over the
metal portion of the terminal. All emergency light switches will be mounted on a separate panel installed in the cab. A master warning light switch and individual switches to be provided to allow pre-selection of emergency lights. The light switches will be "rocker" type with an internal indicator light to show when switch is energized. All switches will be properly identified and mounted in a removable panel for ease in servicing. Identification of the switches will be done by either printing or etching on the switch panel. The switches and identification will be illuminated.

All lights and reflectors, required to comply with Federal Motor Vehicle Safety Standard #108
, will
be furnished. Rear identification lights will be recessed mounted for protection. Lights and wiring mounted in the rear bulkheads will be protected from damage by installing a false bulkhead inside the rear compartments.

An operational test will be conducted to ensure that any equipment that is permanently attached to the electrical system is properly connected and in working order.

The results of the tests will be recorded and provided to the purchaser at time of delivery. 14 771
Bid #:

0762337
Single Start, (3) Grp 31, 660 CCA
each, Ext/Crew Cab, International

BATTERY SYSTEM
A single starting battery system will be provided consisting of three ( 3 )
12 volt,
660
CCA,
maintenance-free, group
31 batteries.

The batteries system will have a total of
1980
CCA with a minimum reserve capacity of
540

minutes.
0768600
Battery Relocation Not Required -
International HV and 4x4

0897716
Battery Location, Top of Crew Cab
Step Compartment, Left Side

BATTERY LOCATION - ABOVE CREW CAB STEP COMPARTMENT
The batteries will be relocated by the apparatus manufacturer. They will be installed on top of the left side crew cab step compartment. That compartment is defined elsewhere in this specification. 0072685
Selector, Single Start Battery,
Commercial Chassis

MASTER BATTERY SWITCH
A master battery switch, to activate the battery system, will be provided inside the cab within easy reach of the driver.

The master battery disconnect switch will be wired between the starter solenoid and the remainder of the electrical loads on the apparatus.

A green "battery on" indicator light, visible from the driver's position, will be provided. 0767193
Charger, Sngl Sys, IOTA, DSL 45, 45
amp, BX3, BX

BATTERY CHARGER
There will be an IOTA, Model DSL
45 ,
45 amp battery charger provided.

The battery charger will be wired to the AC shoreline inlet defined elsewhere in this proposal. 0764272
Location, Charger, in Cab Behind
Crew Cab Seat, BX3

BATTERY CHARGER LOCATION
The battery charger will be located in the cab behind the crew cab seat. 0530960
Not Required, Remote Battery
Charger Indicator

0767064
Shoreline, 20A 120V, Kussmaul Auto
Eject, for Battery Charger, BX3

KUSSMAUL AUTO EJECT FOR SHORELINE
one (
1 ) shoreline inlet
will be provided to operate the dedicated
120
-volt circuits on the truck
without the use of the generator.

The shoreline receptacle (s) will be provided with a NEMA 5-20
,
120
volt,
20 amp, straight blade
Kussmaul auto eject plug with a
red
weatherproof cover. The cover is spring loaded to close, preventing water from entering when the shoreline is not connected.

A solenoid wired to the vehicle's starter is energized when the engine is started. This instantaneously drives the plug from the receptacle.

The shoreline will be connected to the battery charger.

A mating connector body will also be supplied with the loose equipment. 0767063
Shoreline Location, BX3

The shoreline receptacle will be located
on the driver's side, under the crew cab door
.
0607607
Alternator, 325 amp Leece-Neville,
International

ALTERNATOR
The alternator will be a
12 V,
325
Amp, Leece Neville pad mount alternator.
0634181
Load Manager, Inc w/MUX Electrical
System , BX Program

ELECTRONIC LOAD MANAGEMENT
Included with the apparatus manufacturer's electrical system will be a programmable load management system.

This system will monitor the vehicle's
12 -volt electrical system, and automatically reduce the electrical load in the event of a low voltage condition and by doing so, ensures the integrity of the electrical system.
0762588
Cab Lighting, LED
Clearance/Marker/Fender Turn
Signals, International HV

EXTERIOR LIGHTING
Exterior lighting will meet or exceed Federal Department of Transportation, Federal Motor Vehicle Safety Standards and National Fire Protection Association requirements in effect at time of proposal.

Front headlights will be halogen type and comply to all FMVSS requirements.

Five (
5 ) LED clearance and marker lights will be installed across the leading edge of the cab.

TURN SIGNALS, FRONT
LED turn signals which include LED side marker lights will be mounted on the fender. 15 771
Bid #:

0669538
Lights, Clearance/Marker/ID, Rear,
P25 LED 7Lts, Pumper/Tanker/PUC

REAR CLEARANCE/MARKER/ID LIGHTING
There will be three (
3 ) LED identification lights located at the rear installed per the following:

As close as practical to the vertical centerline
Centers spaced not less than

6.00 " or more than

12.00 " apart
Red in color
All at the same height
There will be two (
2 ) LED lights installed at the rear of the apparatus used as clearance lights located at the rear of the apparatus per the following:

To indicate the overall width of the vehicle
One (
1 ) each side of the vertical centerline
As near the top as practical
Red in color
To be visible from the rear
All at the same height
There will be two (
2 ) LED lights installed on the side of the apparatus used as marker lights as close to the rear as practical per the following:

To indicate the overall length of the vehicle
One (
1 ) each side of the vertical centerline
As near the top as practical
Red in color
To be visible from the side
All at the same height
There will be two (
2 ) red reflectors located on the rear of the truck facing to the rear. One ( 1 ) each
side, as far to the outside as practical, at a minimum of

15.00 ", but no more than

60.00 ", above
the ground.

There will be two (
2 ) red reflectors located on the side of the truck facing to the side. One ( 1 )
each side, as far to the rear as practical, at a minimum of

15.00 ", but no more than

60.00 ", above
the ground.

Per FMVSS
108
and CMVSS
108
requirements.
0767050
Lights, Tail, Wln M6BTT* Red LED
Stop/Tail & M6T* Amber LED Dir Arw
For Hsg, BX3

REAR FMVSS LIGHTING
The rear stop/tail and directional LED lighting will consist of the following:

Two (
2 ) Whelen®, Model M
6 BTT, red LED stop/tail lights
Two (
2 ) Whelen, Model M
6 T, amber LED arrow turn lights
The lights shall be provided with
color lenses
.

The lights will be mounted in a polished combination housing. 0561471
Lights, Backup, Wln M6BUW, LED,
For Tail Lt Housing
There will be two (2) Whelen Model M6BUW, LED backup lights provided in the tail light housing. 0664481
Bracket, License Plate & Light, P25
LED

LICENSE PLATE BRACKET
There will be one (
1 ) license plate bracket mounted on the rear of the body.

A white LED light will illuminate the license plate. A stainless steel light shield will be provided over the light that will direct illumination downward, preventing white light to the rear. 0556842
Bezels, Wln, (2) M6 Chrome Pierce,
For mtg (4) Wln M6 lights

LIGHTING BEZEL
There will be two (
2 ) Whelen, Model M
6 FCV
4 P, four (
4 ) place chromed ABS housings with Pierce
logos provided for the rear M
6 series stop/tail, directional, back up, scene lights or warning lights. 0589905
Alarm, Back-up Warning, PRECO
1040

BACK-UP ALARM
A PRECO, Model
1040
, solid-state electronic audible back-up alarm that actuates when the truck is shifted into reverse will be provided. The device will sound at 60 pulses per minute and
automatically adjust its volume to maintain a minimum ten ( 10 ) dBA above surrounding
environmental noise levels.
0767028
Lights, Perimeter Cab, Amdor AY-LB-
12HW012 LED 4Dr, NFPA 1906 BX3

CAB PERIMETER SCENE LIGHTS
There will be four (
4 ) Amdor, Model AY-LB-
12 HW
012
,
190
lumens each,

12.00 " white LED strip
lights provided.

One (
1 ) under the driver's side cab access step.

One (
1 ) under the passenger's side cab access step.

One (
1 ) under the passenger's side crew cab access step.

One (
1 ) under the driver's side crew cab access step.

The lights will be activated when the battery switch is on and the respective door is open and whenever control has been selected for the body perimeter lights. 0769559
Lights, Perimeter Pump House,
Amdor AY-LB-12HW012 LED 2lts

PUMP HOUSE PERIMETER LIGHTS
There will be two (
2 ) Amdor, Model AY-LB-
12 HW
012
,
190
lumens each,

12.00 " LED
weatherproof strip lights with brackets provided under the pump panel running boards, centered front to rear as much as possible, one (
1 ) each side.

The lights will be activated when the battery switch is on, and controlled by the same means as the body perimeter lights.
16 771
Bid #:

0766637
Lights, Perimeter Body, Amdor AY-
LB-12HW012 LED 2lts, Rear Step,
BX3

BODY PERIMETER SCENE LIGHTS
There will be two (
2 ) Amdor, Model AY-LB-
12 HW
012

350
lumens,

12.00 " long
12 volt DC LED
strip lights provided at the rear step area of the body, one ( 1 ) each side shining to the rear.

The perimeter scene lights will be activated when the battery switch is on, and a switch within
reach of the driver is activated and the parking brake is applied .
0764260
Lights, Step, LED, BX3, Prk Brk

STEP LIGHTS
White LED, step lights will be provided to meet the NFPA step lighting requirement. Lights will be provided on each side, on the front compartment face and at the rear to illuminate the tailboard.

These step lights will be activated
when the parking brake is applied
.

All other steps on the apparatus will be illuminated per the current edition of NFPA. 0759408
Lights, Side Scene, Wln PCPSM1C
LED 2nd, RIGHT Side of Body, BX3

SIDE SCENE LIGHTS
There will be
one (
1 )
Whelen®, Model PCPSM
1 C, LED scene light(s) with chrome flange(s)
installed on the side of the apparatus,
one (
1 ) high and forward on passenger's side body
.

SIDE SCENE LIGHTS
There will be
one (
1 )
Whelen®, Model PCPSM
1 C, LED scene light(s) with chrome flange(s)
installed on the side of the apparatus,
one (
1 ) high and forward on driver's side body
.

A control for the light(s) selected above will be the following:
a switch at the driver's side switch panel
a switch at the pump operator's panel
These lights may be load managed when the parking brake is applied. 0772726
Light, Visor, Wln, 12V PCH2* Pioneer
LED Fld/Spt, Brow Mt, Commercial,
BX
12 VOLT LIGHTING
There will be a Whelen® Pioneer
™,
Model PCH
2 *,
12 volt LED light(s) provided. The light will be
mounted on a special bracket painted exterior cab roof color, provided on the front of the cab roof, centered.

The
painted parts of this light assembly to be white
.

The light(s) will be controlled by the following:
a switch at the driver's side switch panel
no additional switch location
These light(s) may be load managed when the parking brake is set. 0603539
Not Required, Deck Lights, Rear,
1906 Wildland or Other Hose Bed &
Rear Lighting
0766626
Lights, Hose Bed, Cover, Dual LED
Light Strips, BX3

HOSE BED LIGHTS
There will be white
12 volt DC LED light strips provided to illuminate the hose bed area. Hose bed lights will be positioned to meet the photometric levels listed in NFPA for hose bed lighting requirements.

The lights will be activated
when the hosebed cover is raised
.
0764255
Lights, Rear Scene, Wln, PCPSM1C
Pioneer LED Fld/Spt, Surface Mount,
BX3, BX

REAR SCENE LIGHT(S)
There will be
two (
2 )
Whelen®, Model PCPSM
1 C, surface mounted LED combination spot/flood
scene light(s) with chrome trim bezel(s) installed at the rear of the apparatus, one (
1 ) each side
high on rear body bulkhead
.

The light(s) will be controlled
by a switch at the driver's side switch panel, by a switch at the driver's side pump panel and by a cup switch at the driver's side rear bulkhead .

The light(s) may be load managed when the parking brake is applied. 0763429
Lights, Walk Surf, Additional Not
Req'd, Hose Bed Light Adequate,
BX3

WALKING SURFACE ILLUMINATION
Additional lighting for the designated walking surface willl not be required. The light for illuminating the hose bed willl be adequate for the walking surface also. 0627706
WILDLAND BX3, Type 3, NFPA 1906
17 771
Bid #:

0773467
Water Tank, Poly, 500 Gallon,
Wildland BX3

WATER TANK
Booster tank will have a capacity of
500
gallons and be constructed of polypropylene plastic by
United Plastic Fabricating, Incorporated.

Tank will be designed to provide for deep side compartments and to serve as a large sump to limit the amount of undraftable water.

Tank joints and seams will be nitrogen welded inside and out.

Tank will be baffled in accordance with applicable NFPA for the type of truck being constructed.

Baffles will have vent openings at both the top and bottom to permit movement of air and water between compartments.

Longitudinal partitions will be constructed of .
38 " polypropylene plastic and will extend from the
bottom of the tank through the top cover to allow for positive welding.

Transverse partitions will extend from

4.00 " off the bottom of the tank to the underside of the top cover.

All partitions will interlock and will be welded to the tank sides.

Fill tower will be constructed of .
50 " polypropylene. It will have a .
25 " thick polypropylene screen
and a hinged cover.

An overflow pipe, constructed of

4.00 " schedule
40 polypropylene, will be installed approximately
four inches down the fill tower and extend through the water tank and dump to the rear of the rear axle.

Tank top will be constructed of .
50 " polypropylene. It will be recessed .
38 " and will be welded to
the tank sides and the longitudinal partitions.

Tank top will be sufficiently supported to keep it rigid during fast filling conditions.

Construction will include

2.00 " polypropylene dowels spaced no more than

30.00 " apart and
welded to the transverse partitions. A minimum of two ( 2 ) of the dowels will be drilled and tapped
(.
50 " diameter,

13.00 " deep) to accommodate lifting eyes.

A sump will be provided at the bottom of the water tank, and will include a drain plug and the tank outlet.

The tank will be installed in a fabricated cradle assembly constructed of structural steel.

Sufficient crossmembers will be provided to properly support bottom of tank. Crossmembers will be constructed of steel flat bar or rectangular tubing.

Tank will "float" in cradle to avoid torsional stress caused by chassis frame flexing. Rubber cushions, .
50 " thick x

3.00 " wide, will be placed on all horizontal surfaces that the tank rests on.

Stops or other provision will be provided to prevent an empty tank from bouncing excessively while moving vehicle.

Mounting system to be approved by the tank manufacturer.

WATER TANK WARRANTY
Tank will have a
lifetime
warranty.
0003405
Overflow, 4.00" Water Tank, Poly

Fill tower will be constructed of .
50 " polypropylene and will be a minimum of

8.00 " wide x

14.00 "
long.

Fill tower will be furnished with a .
25 " thick polypropylene screen and a hinged cover.

An overflow pipe, constructed of

4.00 " schedule
40 polypropylene, will be installed approximately
halfway down the fill tower and extend through the water tank and exit to the rear of the rear axle. 0766960
Foam Tank, Separate, Required

0553725
Restraint, Water Tank, Heavy Duty,
Special Type Tank, 4x4, or Export

WATER TANK RESTRAINT
A heavy-duty water tank restraint will be provided.
0768625
Tank Fill, Direct, Rear, 2.50",
Wildland

DIRECT TANK FILL
There will be
one (
1 )
-

2.50 " gated external tank fill(s) installed and properly labeled at the rear of the truck. It will be
centered
, with the valve installed as low as practical for easy hose connection.

Piping, for the fill, will include a flow deflector to break up the stream of water entering the water tank.

2.50 " full flow ball valve with

2.50 " piping and a

2.50 " (F)NST chrome swivel will be located at
the inlet.

2.50 " SFT style check valve will be provided to prevent backflow.

A
chrome plated plug and chain
will be provided for the tank fill.
0746890
SP
Bleeder, .75", Direct Tank Fill(s), BX3

.
75 " BLEEDER VALVE
A .
75 " bleeder valve will be provided for
one (
1 )

2.5 " direct tank fill(s) located rear . The bleeder
valve will be installed on the inlet side of the direct tank fill valve. 0773432
Hose Bed, Wildland BX3

HOSE BED
Two main hose storage areas will be provided, one (
1 ) on each side at the top of the truck. (In the
center of the hose bed will be an equipment storage area as defined elsewhere in this specification.) Each hose storage area will be about

21.00 " wide x
101.00
" long (the length of the
body) x

20.00 " deep.

Flooring of the hose bed areas will be removable aluminum grating with the top surface corrugated to aid in hose aeration. The grating slats will be a minimum of

0.50 " x

4.50 " with
spacing between slats for hose ventilation.
18 771
Bid #:

0762116
Hose Bed Capacity, 500' of 2.50"
Hose, Wildland BX3

HOSEBED CAPACITY
The hosebed shall be of a fixed design and capacity and shall accommodate a typical wildland truck rolled or flat hose storage requirements per NFPA 1906
.

There shall be hose storage on each side at the top of the truck with equipment / tool storage in the middle. (This center storage is defined elsewhere in this proposal.) Each side shall have a hose storage space of at least
25 cubic feet, with a total hose bed volume of at least

50.00 cubic
feet.
0759906
Divider, Hose Bed, .25" Unpainted,
w/Hand Hold, BX3, BX

HOSE BED DIVIDER
Two (
2 ) adjustable hosebed dividers
will be furnished for separating hose.

Each divider will be constructed of a .
25 " brushed aluminum sheet. Flat surfaces will be sanded for uniform appearance, or constructed of brushed aluminum.

An oval opening will be provided near the rear of the divider to be used as a hand hold and aid in accessing the hosebed.

Divider will be fully adjustable by sliding in tracks, located at the front and rear of the hose bed.

Divider will be held in place by tightening bolts, at each end.

Acorn nuts will be installed on all bolts in the hose bed which have exposed threads.

Divider(s) will be located in the hose bed on the
left and right
.
0751228
Covers, Hose Bed, Alum Treadplate,
4-Section, Wildland BX3

HOSE BED COVERS
A four-section aluminum treadplate hose bed cover will be provided - two sections (one forward and one rearward) for each side of the hose bed. The covers will be hinged on the outboard side using a full length stainless steel hinge.

The covers will be reinforced so that they can support the weight of a person walking on the cover.

Gas shocks will aid in opening the covers and keeping them in the upright position. A safety strap to keep the covers from traveling over center will be provided.

To keep them in the closed position, a latch will be provided at the rear of each rearward cover.

When closed, the rearward cover will be designed to keep the forward cover in the closed position. These rear positioned latches will not require climbing on top of the covers to unlatch them.
0761425
Flap, Rear of Alum Hose Bed Cover,
Two Piece, Vinyl, w/Seat Belt
Buckles, BX3

HOSEBED END FLAP
A pair of
red
vinyl flaps will be installed on the rear, one for each of the aluminum treadplate hose bed covers.

Each vinyl flap will have (
2 ) nylon tie down straps, with seat belt buckles.
0768124
Top of Truck Gear and Equipment
Storage, BX3

TOP OF TRUCK GEAR & EQUIPMENT STORAGE
At the top of the truck will be three (
3 ) compartments for the storage of gear and equipment.

Two (
2 ) of these storage compartments will be located toward the outside of the hose bed, one (
1 ) on each side of the truck. These compartments will be constructed from stainless steel and incorporated into the body design and construction.

Each of these compartments will be about

13.00 " wide x

17.00 " deep x
100.00
" long. Access into
these compartments will be at the rear and top. There will be a single pan vertically hinged door at the rear for each compartment. It will be constructed from brushed stainless steel and have a black push-to-open latch. The top of each of these compartments will be covered by the aluminum hose bed covers. When the hose bed covers are in the open position, contents of these compartments can be accessed from the top.

The interior of these compartments will remain unpainted natural stainless steel. The floor will be smooth stainless steel and include drain holes.

In the center/rear of the hose bed will be a gear/equipment storage compartment. It will be constructed from unpainted smooth aluminum. It will be about

30.00 " wide x

20.00 " deep x

66.00 "
long. Access will be from the top. A reinforced aluminum treadplate door, with a full-length stainless steel hinge will be provided. A locking D-ring latch will hold the door closed. The interior, including the floor, will be unpainted smooth aluminum. Drain holes will be provided in the floor.

WATER AND FOAM TANK DOME ACCESS
Forward of the center hose bed gear/equipment compartment will be an area primarily for housing the water and foam tank domes. The dimensions of this tank dome compartment will be about

30.00 " wide x

20.00 " deep x

34.00 " long. It will be constructed from smooth unpainted aluminum.

The tank domes will be accessed through an aluminum treadplate door on the top of this compartment that matches the construction of the center storage compartment. It will also have a full-length stainless steel hinge and a locking D-ring latch. 0768331
Running Boards, Wildland BX3

RUNNING BOARDS
Running boards on each side of the pump module will be fabricated of . 125
" bright aluminum
treadplate. The outer edge of the treadplate will have a punched design for extra stepping traction.

Each running board will be supported by a welded tubing and channel assembly, which will be bolted to the pump compartment substructure and spaced . 50 " away from the pump panel.
19 771
Bid #:

0766413
Tailboard, w/Hinged Drop-Down
Step, Wildland BX3

REAR STEP/TAILBOARDS
A pair of

10.00 " deep tailboard/steps will be provided at the rear, one each side behind the rear body bulkheads. The supporting framework will be covered with bright aluminum treadplate and will incorporate a punched design along the rearward edge for extra stepping traction.

A hinged drop-down / lift-up style of step with a traction grip stepping surface will also be provided on each side of the truck to meet NFPA first-step height requirements. It will store in a manner that does not inhibit the rear angle of departure.

Steps and tailboards will meet NFPA requirements.
0607673
Wall, Rear, Aluminum Treadplate,
Wildland BX3

REAR WALL, ALUMINUM TREADPLATE
The rear facing surfaces of the center rear wall directly below the hose bed will be aluminum treadplate. This treadplate serves as a kick-plate surface for the rear access steps.

The bulkheads (the surface to the rear of the side body compartments) will be smooth and the same material as the body.
0766412
Tow Eyes, 1906 Wildland BX3/BLM

TOW EYES
Two (
2 ) rear "tow" eyes will be located at the rear of the apparatus. They will be a shackle style tow eye and will be mounted to a framework attached directly to the chassis frame rails. 0773465
Construction, Compartment,
Stainless Steel, Wildland BX3

COMPARTMENTATION
The body and compartments will be fabricated of corrosion resistant, low carbon austenitic, brushed and painted
304
L stainless steel. Due to superior corrosion resistance of 300
stainless
grades, other grades of austenitic stainless steels, or any grade of ferritic or martensitic stainless, will not be acceptable.

The side compartments will be an integral assembly with the rear fenders.

Removable circular fender liners will be provided for prevention of rust pockets and ease of maintenance.

The compartment flooring will be of the sweep out design with the floor higher than the compartment door lip.

The front facing compartment walls will be covered with bright aluminum treadplate.

All screws and bolts which protrude into a compartment will have acorn nuts on the ends to prevent injury.

UNDERBODY SUPPORT SYSTEM
Due to the severe loading requirements of this Wildland truck, a method of body and compartment support suitable for the intended load will be provided.

The backbone of the support system will be the chassis frame rails which is the strongest component of the chassis and is designed for sustaining maximum loads.

AGGRESSIVE WALKING SURFACE
All exterior surfaces designated as stepping, standing, and walking areas will comply with the required average slip resistance of the current NFPA standards.

TESTING OF BODY DESIGN
Body structural analysis will be fully tested. Proven engineering and testing techniques such as finite element analysis, stress coating and strain gauging have been performed with special attention given to fatigue, life and structural integrity of the body and substructure.

A similar body design will be tested while loaded to its greatest in-service weight.

The criteria used during the testing procedure will include:
- Raising opposite corners of the vehicle tires

12.00 " to simulate the twisting a truck may
experience when driving over a curb.
- Making a
90 degree turn, while driving at
20 mph to simulate aggressive driving conditions.
- Driving the vehicle at
35 mph on a "washboard" road.
- Driving the vehicle at
55 mph on a smooth road.
- Accelerating the vehicle fully, until reaching the approximate speed of 45 mph on rough
pavement.

Evidence of actual testing techniques will be made available upon request. 20 771
Bid #:

0773598
LS, Flush Style Door, Full-Depth,
Wildland BX3

LEFT SIDE COMPARTMENTATION
A vertically hinged double door compartment over the rear wheels will be provided. The interior dimensions of this compartment will be

58.00 " wide x

39.00 " high x

23.50 " deep. The depth of the
compartment will be calculated with the compartment door closed. The clear door opening of this compartment will be

55.00 " wide x

39.00 " high.

Positive door holders will be furnished with this compartment.

A full height, vertically hinged, single door compartment behind the rear wheels will be provided.

The interior dimensions of this compartment will be

34.00 " wide x

59.00 " high x

23.50 " deep. The
depth of the compartment will be calculated with the compartment door closed. The compartment interior will be fully open from the compartment ceiling to the compartment floor and designed so that no permanent dividers are required between the upper and lower sections. The clear door opening of this compartment will be

31.00 " wide x

59.00 " high.

A positive door holder will be furnished with this compartment.

The rear compartment will be designed to provide a superior angle of departure suitable for off- road use.

Main body compartments will be vented. The vents will allow air circulation between compartments and/or to the outside atmosphere. They will be designed and located for optimum performance.

TOOL COMPARTMENT
Located below the compartment behind the rear wheels will be a tool compartment. This compartment will be about

24.75 " deep and have a door opening of about

19.00 " wide x

7.50 "
high. It will have a single pan horizontally hinged drop-down door. The door will be constructed from brushed stainless steel and have a black push-to-open latch.

FENDER PANEL STORAGE COMPARTMENT
Two (
2 ) fender panel storage compartments will be provided. They will be located ahead of and behind the rear wheel in the body fender panel.

These compartments will be designed to make use of the available space within the fender panel.

The compartments will be sized as large as practical to allow for the storage of an air bottle, air pack or other tools or equipment. A drain hole will be provided in the bottom of the compartment.

A brushed stainless steel door with a black push-to-open latch will be provided on each compartment. A dielectric barrier will be provided between the door hinge, hinge fasteners and the body sheet metal.
0773597
RS, Flush Style Door, Full Depth,
w/Ladder Storage, Wildland BX3

RIGHT SIDE COMPARTMENTATION
A vertically hinged double door compartment over the rear wheels will be provided. The interior dimensions of this compartment will be

58.00 " wide x

39.00 " high x

11.50 " deep. The depth of the
compartment will be calculated with the compartment door closed. The clear door opening of this compartment will be

55.00 " wide x

39.00 " high.

Positive door holders will be furnished with this compartment.

A full height, vertically hinged, single door compartment behind the rear wheels will be provided.

The interior dimensions of this compartment will be

34.00 " wide x

59.00 " high x

23.50 " deep in
the lower

21.00 " of the compartment and

11.50 " deep in the remaining upper portion. The depth
of the compartment will be calculated with the compartment door closed. The compartment interior will be fully open from the compartment ceiling to the compartment floor and designed so that no permanent dividers are required between the upper and lower sections. The clear door opening of this compartment will be

31.00 " wide x

59.00 " high.

A positive door holder will be furnished with this compartment.

The rear compartment will be designed to provide a superior angle of departure suitable for off- road use.

The back wall of the above compartments will be removable to allow access to the interior of the ladder storage area as defined elsewhere in this specification.

Main body compartments will be vented. The vents will allow air circulation between compartments and/or to the outside atmosphere. They will be designed and located for optimum performance.

TOOL COMPARTMENT
Located below the compartment behind the rear wheels will be a tool compartment. This compartment will be about

24.75 " deep and have a door opening of about

19.00 " wide x

7.50 "
high. It will have a single pan horizontally hinged drop-down door. The door will be constructed from brushed stainless steel and have a black push-to-open latch.

FENDER PANEL STORAGE COMPARTMENT
Two (
2 ) fender panel storage compartments will be provided. They will be located ahead of and behind the rear wheel in the body fender panel.

These compartments will be designed to make use of the available space within the fender panel.

The compartments will be sized as large as practical to allow for the storage of an air bottle, air pack or other tools or equipment. A drain hole will be provided in the bottom of the compartment.

0768326
Doors, ALUMINUM, FLUSH STYLE
w/"D" Handle - Side Compartments,
Wildland BX3

DOORS, SIDE COMPARTMENTS
All hinged body side compartment doors will be will be fabricated of 5052
-H
32 aluminum with a
tensile strength range of
31,000
to
38,000
psi. They will be flush style with double pan
construction.

Doors will have a full interior panel. To provide additional door strength, a "C" section reinforcement will be installed between the outer and interior panels.

A closed cell rubber gasket will be installed to provide a weather resisting compartment seal.

A stainless steel continuous hinge will be provided on each compartment door.

Door lock mechanisms will be protected to prevent fouling of the lock in the event equipment inside shifts onto the lock area.

Latches will be recessed with polished stainless steel "D" ring handles. A gasket will be provided between the "D" ring handle and the door.

SCUFFPLATE ON INTERIOR OF COMPARTMENT DOOR(S)
There will be a
a brushed stainless steel scuffplate
installed on the
inside panel of
each door pan
that covers the width and height of the door.

Scuffplates will be located on all main body compartment doors as follows:

B
1 , LS
1 ,
LS
2 , RS
1 , RS
2 and RS
3 .
0615834
Rear Compt, Flush Style Door,
Wildland BX3

COMPARTMENTATION, REAR
A vertically hinged, double door compartment at the rear of the truck will be provided. Interior dimensions of this compartment will be

48.00 " wide x

45.00 " high x

25.50 " deep. Depth of the
compartment will be calculated with the compartment door closed.

Clear door opening of this compartment will be

30.00 " wide x

39.00 " high.

Each of the vertically hinged compartment doors will be provided with a positive door holder. 0626754
Doors, ALUMINUM, FLUSH STYLE
w/"D" Handle - Rear Compartment,
Wildland BX3

DOORS, REAR COMPARTMENT
The rear compartment doors will be will be fabricated of . 125
",
5052
-H
32 aluminum with a tensile
strength range of
31,000
to
38,000
psi. They will be flush style with double pan construction.

Doors will have a full interior panel. To provide additional door strength, a "C" section reinforcement will be installed between the outer and interior panels.

The doors will be provided with a closed cell rubber gasket to provide a weather resisting compartment seal.

A stainless steel continuous hinge will be provided on each compartment door.

Door lock mechanisms will be protected to prevent fouling of the lock in the event equipment inside shifts onto the lock area.

Latches will be recessed with polished stainless steel "D" ring handles. A gasket will be provided between the "D" ring handle and the door.
0597111
Not Required, Pull Strap

0738852
Keyed Locks for Latches, Key Style
1250, Body Compts, Wildland BX3

KEYED LOCK(S) - BODY COMPARTMENTS
The main body compartment door D-ring latches will be furnished with a keyed lock utilizing key style
#1250
. This includes compartments: LS
1 and LS
2 , RS
1 , RS
2 and RS
3 (pump house
compartment) and the rear compartment (B
1 ).

Other storage areas that also use the same size D-ring latch will also be the key #1250
locking
style. These compartments are: the ladder storage door at the rear of the truck, the gear and equipment storage compartment and water/foam dome cover above the water tank. 0766933
Lights, Body Compt, Pierce LED,
Dual Lt Strips, Each Side of Door,
BX3

COMPARTMENT LIGHTING
There will be
six (
6 )
compartment(s) with two (
2 ) white
12 volt DC LED compartment light strips.

The dual light strips will be centered vertically along each side of the door framing. There will be two (
2 ) light strips per compartment. The dual light strips will be in compartment(s):

R
1 , LS
1 , LS
2 ,
RS
1 , RS
2 and RS
3 and the tool/equipment compartment on the right side pump panel.

A single LED strip light will be provided in each tool compartment located below each rear/side (LS
1 /RS
1 ) compartment.

Opening the compartment door will automatically turn the compartment lighting on. 0768324
Shelf Tracks, Unpainted, Wildland
BX3

MOUNTING TRACKS
There will be
five (
5 ) sets of tracks
for mounting shelf(s) in
LS
1 , LS
2 , RS
1 , RS
2 and B
1 . These
tracks will be installed vertically to support the adjustable shelf(s), and will be full height of the compartment. The tracks will be unpainted with a natural finish. 0766575
Shelves,Adjustable,500 lb
Capacity,Full Width/Depth,Brushed
Alum,Wildland BX3,BX

ADJUSTABLE SHELF
There will be
nine (
9 ) shelves
provided. Each shelf will be constructed of

0.188
" aluminum with

2.00 " high sides. Each shelf will as wide and as deep as the compartment space will allow.

Each shelf will have a brushed finish.

Each shelf will have a load capacity of
500
lb.

Each shelf will be infinitely adjustable by means of a threaded fastener, which slides in a track.

The shelves will be held in place by

0.12 " thick stamped plated brackets and bolts.

The location will be
in RS
1 at the transition point, in RS
2 centered between the floor and the
ceiling, in RS
1 in the lower third, in RS
1 in the upper third, in LS
2 centered between the floor and
ceiling, in B
1 centered between the floor and ceiling, in LS
1 in the lower third, in LS
1 in the upper
third and in LS
1 in the upper third
.
22 771
Bid #:

0766573
Tray, Floor Mounted, Slide-Out,
500lb, 2.00" Sides, Wildland BX3, BX

SLIDE-OUT FLOOR MOUNTED TRAY
There will be
two (
2 )
floor mounted slide-out tray(s) provided.

Each tray will have

2.00 " high sides and a minimum capacity rating of
500
lb in the extended
position.

Each tray will be constructed of aluminum
with a brushed finish
There will be two undermount-roller bearing type slides rated at 250
lb each provided. The pair of
slides will have a safety factor rating of
2 .

To ensure years of dependable service, the slides will be coated with a finish that is tested to withstand a minimum of
1,000
hours of salt spray per ASTM B
117
.

To ensure years of easy operation, the slides will require no more than a 50 lb force for push-in or
pull-out movement when fully loaded after having been subjected to a 40 hour vibration (shaker)
test under full load. The vibration drive file will have been generated from accelerometer data collected from a heavy truck chassis driven over rough gravel roads in an unloaded condition.

Proof of compliance will be provided upon request.

Automatic locks will be provided for both the "in" and "out" positions. The trip mechanism for the locks will be located at the front of the tray for ease of use with a gloved hand.

The location(s) will be
RS
1 and LS
1 .
0766572
Toolboard, Swing-out, Alum, .188",
Peg Board, Wildland BX3, BX

SWING OUT TOOLBOARD
A swing out aluminum toolboard will be provided.

It will be a minimum of .
188
" thick with .
20 " diameter holes in a pegboard pattern with

1.00 "
centers between holes.

1.00 " x

1.00 " aluminum tube frame will be welded to the edge of the pegboard.

The board will be mounted on a pivoting device at the
front
of the compartment on the top and
bottom to allow easy movement in and out of the compartment. The maximum tool load will be 400
pounds.

The board will have positive lock in the stowed and extended position.

The board will be
mounted on adjustable tracks from front to back within the compartment .

There will be
One (
1 )
toolboard(s) provided. The toolboard(s) will be
with a brushed finish
and
installed
LS
2 .
0746904
Dust Filter, Compt Louvers, BX3

COMPARTMENT DUST FILTERS
A total of
seven (
7 )
body compartments with louvers will have a removable dust filter installed to restrict road dirt from easily entering the compartments. 0004015
Trim, Alum Treadplate on Lower
Body

LOWER BODY TRIM
Bottom edge of the side compartments will be trimmed with bright aluminum treadplate.

Trim will be about

2.00 " high. It will not be an integral part of the body construction, which allows easy replacement in the event of damage.
0739426
Fender Crowns, Rear, Rubber,
w/Removable Liner, BX3

BODY FENDER CROWNS
Black rubber fender crowns will be provided around the rear wheel openings.

BODY FENDER LINER
A
painted
fender liner will be provided. The liners will be removable to aid in the maintenance of rear suspension components.
0766678
Hose, Hard Suction, Provided by
Dealer, NFPA 1906 2016, Wildland

HARD SUCTION HOSE
NFPA
1906
,
2016
edition, section

16.13.2.2.1 references suction hose.

Hose is not on the apparatus as manufactured. The dealer will provide suction or supply hose. 0759425
Storage, HSH, (2), Enclosed in Single
Hatch Compt, BX3

HARD SUCTION HOSE STORAGE
Storage for two (
2 ) lengths of

3.00 "
hard suction hose
7 '
will be provided.

The hoses will be carried the equipment storage compartment (hatch) located at the outside of the hose bed areas on the
on the left side
of the truck. (These equipment storage compartments
(hatch) are defined elsewhere in this specification.)
A stainless steel non-adjustable trough will be provided so the hoses can be stored one above the other. A poly material will be provided on the bottom of each storage area within this hatch compartment.
0527021
Handrails Located @ Front Body

HANDRAILS
The handrails will be

1.25 " diameter knurled aluminum to provide a positive gripping surface.

Chrome plated end stanchions will support the handrail. Plastic gaskets will be used between end stanchions and any painted surfaces.

Drain holes will be provided in the bottom of all vertically mounted handrails..

Handrails will be located on the front of the body in positions needed to meet NFPA requirements. 0531152
Handrails, Rear Bulkhead, Wildland

One (1) vertical handrail, with chrome stanchions will be located on each rear bulkhead. 0758878
Handrail, Rear, Above Hose Bed,
BX3
One (1) handrail will be installed above the hose bed.
23 771
Bid #:

0759000
W-Insert, For (3) Air Bottle Storage,
Tool Compartment, BX3
AIR BOTTLE STORAGE in TOOL COMPARTMENT
A quantity of
one (
1 )
body tool compartment(s) will be converted to air bottle storage.

A W-style insert will be installed inside the tool compartment on the right side behind the rear
wheel
.

The addition of this insert will provide storage for three ( 3 ) air bottles per compartment with a
maximum diameter of no larger than

6.00 " and a length of no more than

24.75 ".
0759676
Ladder, 20' Duo-Safety 912-100 3-
Sect, 100" Closed Length, BX

EXTENSION LADDER
There will be a
20 ', three (
3 )-section, aluminum, Duo-Safety, Series
912-100
extension ladder
provided.
0074231
No Roof Ladder Req'd

0773396
Ladders, Encl'd Complete, in RS
Body, w/Pike Poles, Wildland BX3

LADDER STORAGE
A ladder storage area will be provided inside the upper section of the right side compartments.

The ladder rack will reduce the depth of the upper section in the side compartments by approximately

12.00 ". Partitions will be installed inside the compartments to conceal the ladder storage. The area will extend the full length of the body and will be enclosed to protect the ladders and other equipment from road dirt. The ladder will be stored vertically with stainless steel and Dura-Surf slides to aid in loading and unloading of the ladders.

Two (
2 ) aluminum pike pole storage tubes will be provided above the ladder storage. Access will be at the rear via a vertically hinged single pan aluminum treadplate door with a locking "D-ring" latch.

The ladder storage will accommodate a
20 ' aluminum extension ladder (Duo Safety model
#912

or equivalent) and
2 pike poles (standard or all-purpose head).
0074248
Not Required, Folding Ladder

0758983
Pike Pole, 6' DUO Safety, Fiberglass,
BX3

PIKE POLE,
6 '
One (
1 ) pike pole

6 ' long DUO Safety with a fiberglass handle, will be provided and located in the
ladder storage compartment
.
0758982
Pike Pole, 8' DUO Safety, Fiberglass,
BX3

PIKE POLE,
8 '
One (
1 ) pike pole

8 ' long DUO Safety with a fiberglass handle, will be provided and located in the
ladder storage compartment
.
0745377
SP
I Zone Bracket, Pair, Located
Inboard, Wildland Style

I-ZONE BRACKETS - WILDLAND STYLE - INBOARD
A pair of I-Zone brackets will be provided and mounted at the rear of the apparatus, one each side, located inboard under the rear access steps. The brackets will be designed with adequate reinforcement to eliminate flexing of the body (oil canning) and not interfere with rear facing lights while carrying hose.

The design of these I-Zone brackets will have a
45 degree receiver and a removable extension
piece that fits into the brackets for carrying hose.
0768315
Steps,(4) Cast Products,Model
SP2011-1/(2) Model SP2016-1,Rear
Body,Wildland BX3

REAR ACCESS STEPS
A quantity of six (
6 ) wedge style steps will be provided at the rear for access to the hose bed. The first step on each side will be

14.00 " wide by

8.00 " deep - Cast Products model SP
2016-1
or
equivalent.

The second and third step on each side will be

6.50 " wide by

8.00 " deep - Cast Products model
SP
2011-1
or equivalent. Each step will include a handhold and an LED light provided above the step surface.
0762015
Step Access to Running Boards,
w/4x4 Chassis, Wildland BX3
ACCESS to PUMP HOUSE RUNNING BOARDS
Access to the pump house running boards will be via the crew cab access steps. For break over and ground clearance purposes, additional steps below the running boards are not desired. 0766970
Auxiliary Pump, Hydraulic Drive
(Price Only)
24 771
Bid #:

0766267
Pump,Auxiliary, Darley,1.5AGH,Hyd
PTO Drive,150 GPM, 2016 NFPA
1906,Wildland BX3

AUXILIARY PUMP
A hydraulic driven Darley

1.5 AGH centrifugal pump will be provided for pump and roll operations.

The pump will have a

2.00 " suction inlet and a

2.00 " discharge port. The pump will have a gear
type hydraulic motor. The pump case will be vertically split for removal and service of the impeller. A Viton, carbon/ceramic shaft seal will be provided. The pump shaft and wear ring will be stainless steel.

A variable displacement piston type hydraulic pump supplying the hydraulic motor on the water pump will be supplied. The displacement of the hydraulic pump will be controlled by a fixed orifice type, load sensing, hydraulic circuit. The hydraulic system will have a properly sized reservoir, cooler, filter and accessory components. The components will be mounted in the vehicle body to facilitate routine maintenance operations. The hydraulic drive design will be certified by manufacturer of the primary hydraulic components as suitable for the intended use and duty.

All components of the water pump and drive system will be readily available on the domestic hydraulic market (USA).

An auxiliary pump drain will be supplied.

AUXILIARY PUMP PERFORMANCE
The pump will be rated by the pump manufacturer on bench testing to the deliver the following performance at
1000
engine rpm. These numbers will be reduced when installed on the apparatus due to plumbing restrictions and/or the location of this water pump. -
150
gpm @
80 psi
-
100
gpm @
200
psi
-
35 gpm @
300
psi
This pump will also meet NFPA
1906
section

16.2.2.1 for pump and roll
performance/requirements. It will deliver
20 gpm @
80 psi while moving at
2 mph or less.
0626923
Installation Location, Aux Pump,
Inside Pump house Area

AUXILIARY PUMP INSTALLATION
The auxiliary pump will be installed and located within the main pump module. 0788341
Not Required, Fuel Supply,
(Hydraulic Drive Pump)

0626844
Not Required, Exhaust Routing, Aux
Pump
0787477
Discharge Connections, Aux Pump,
Standard, w/Foam System

AUXILIARY PUMP DISCHARGE CONNECTIONS
A discharge manifold will be supplied as required to allow plumbing of the required discharges.

This pump will supply water to
all foam capable discharge outlets
Check valve(s) will be provided to prevent backflows between the main pump and the auxiliary pump.
0786060
Tank to Pump Line, Hyd Aux Pump,

2.00", Separate Tank to Pump Line

AUXILIARY PUMP -TANK TO PUMP CONNECTION
An independent

2.00 " tank to pump piping with a

2.00 " valve will be provided for the auxiliary
pump. It will not be part of the main pump's tank to pump line nor draw water through the main pump.

The design will include a method for anti-swirl protection and prevent pump cavitation.

The tank to pump line will run from the pump into the front face of the water tank. A rubber coupling will be included in this line to prevent damage from vibration or chassis flexing. A check valve will be provided in the tank to pump supply line to prevent the possibility of "back filling" the water tank.

This tank to pump connection will have an electric valve that will open when the Pierce hydraulic pressure controller(s) "ON" switch is activated. The valve will close when the "OFF" switch is activated. The electric tank to pump valve will not be gateable. 0626935
Primer, Aux Pump, Included w/Main
Pump Primer

AUXILIARY PUMP PRIMER
The auxiliary pump system will be primed with the main pump primer as defined elsewhere in this specification.
0766930
Controls, Hydraulic Aux Pump,
Pierce, Dual,In Cab and at Pump
Panel,Wildland BX3

AUXILIARY PUMP GAUGES AND CONTROLS
The auxiliary pump system will be activated by a switch in the cab near the driver's position and on the left pump operator's panel.

To control the pump pressure, a Pierce electronic water pressure controller will also be provided in the cab near the driver's position and on the left pump operator's panel.

The panel containing the activation switch will also include a digital pressure gauge, pump and system status indicators and the pressure adjustment knob. 0626933
Line, Recirculating, Aux Pump,
499gpm and less, 0.375", Automatic

AUXILIARY PUMP AUTOMATIC RECIRCULATING LINE
The auxiliary pump will be furnished with a

0.375
" automatic pump recirculating line with a check
valve. The line will be routed from the discharge side of the auxiliary pump to the water tank.

This line will be designed to circulate water continuously from the auxiliary pump back to the tank to help maintain the water pump temperature at a safe level.

The recirculating line will be plumbed into the water tank dome. It will include a check valve to facilitate priming and prevent water backflow. The check valve will be installed as close as possible to the water tank dome.
25 771
Bid #:

0766268
Engineering Review of Aux Pump
System Not Req'd - Wildland BX3
0773415
Pump House, Side Control, 28",
Wildland BX3

PUMP COMPARTMENT
The pump compartment will be manufactured separate from the hose body and compartments. It will be a fabricated assembly of stainless steel tubing, angles and channels which supports both the fire pump and the side running boards.

The pump compartment will have substructure to facilitate the pump mounting. The substructure will be mounted on the chassis frame rails with rubber isolators in a four point pattern to allow for chassis frame flex while in motion.

Pump compartment, pump, plumbing, gauge panels, hose body and compartments will be detachable and removable from the chassis and body as a single assembly.

PUMP MOUNTING
Pump will be mounted to the substructure which is attached to the chassis frame rail using the rubber isolators. The mounting allows for vehicle flex while maintaining pump alignment within the pump compartment.

PUMP CONTROL PANELS (Side Control)
All pump controls and gauges will be located at the left side of the apparatus and properly marked.

The pump panels will be fastened to the enclosure with screws.

The pump module will have a nominal width of

28.00 ".

Brushed stainless steel trim collars will be installed around all inlets and outlets.

Valve controls will have locking control rods.

IDENTIFICATION TAGS
All discharge outlets will have color coded identification tags, with each discharge having its own unique color. Color coding will include the labeling of the outlet and the drain for each corresponding discharge.
0802423
SP
Compartment and Enclosure, Above
Pump, RS, with Divider, BX3

CARGO COMPARTMENT and ENCLOSURE
There will be an enclosed storage compartment provided above the above the pump on the right side. The compartment will be constructed from aluminum. The dimensions of the compartment will be as large as practical to make use of the available space. The door over this storage space will not be ventilated.

The interior of the compartment will remain unpainted natural aluminum. A drain hole will be provided in a bottom corner to allow any water that might enter to escape.

A single LED strip light will be provided on the interior and will automatically illuminate when the door is opened.

The hydraulic reservoir for the hydraulic auxiliary pump and/or foam system will be located on the inboard side of the storage compartment. There will be a divider separating it from the storage area. This enclosure will be properly ventilated to allow cooling for the hydraulic reservoir.

An
aluminum treadplate
lift-up door will be furnished on top of the compartment and enclosure.

The doors will be hinged on the forward edge, and a gas-charged cylinder will hold the doors in the open position. A latch matching other doors on the truck will hold the door in the closed position. The door will be connected to the Do Not Move light in the cab. 0769817
Pump, Darley, LSP, 1000 GPM,
Single Stage, PTO Drive, Wildland
BX3
PUMP
Pump will be a Darley LSP
1000
gpm midship mounted centrifugal type. It will be driven by power take off (PTO) from the vehicle transmission.

Pump will deliver the percentage of rated discharge at pressures indicated below:
-
100%
of rated capacity at
150
psi net pump pressure.
-
70%
of rated capacity at
200
psi net pump pressure.
-
50%
of rated capacity at
250
psi net pump pressure.

Pump body will be fine-grained gray iron, bronze fitted. The pump will be easily separated from a one-piece section for convenient servicing when required.

The impellers will be high strength bronze alloy accurately balanced and splined to pump shaft for precision fit and durability. Double seal ring design will help to minimize end thrust.

Deep groove radial type oversize ball bearings will be provided. The bearings will be protected at the openings from road dirt and water with an oil seal and a water slinger. 0007153
Seal, Mechanical, Darley, Silicon
Carbide

MECHANICAL SEALS
Silicon carbide mechanical seals will be provided. The seals will be spring loaded and self- adjusting. The seals will have a minimum thermal conductivity of 126
W/m*K to run cooler. Seals
will have a minimum hardness of
2800
kg/mm
2 to be more resistant to wear, and have thermal
expansion characteristics of no more than

4.0 X
106
mm/mm*K to be more resistant to thermal
shock.
0014633
Trans, Pump, Darley, PTO, 3 Gear

PUMP TRANSMISSION
A three gear transmission with helical gears and a

1.375
" diameter splined shaft will be provided.

The pump transmission will be driven by a hot shift PTO attached to the Allison Transmission. 0603731
Pumping Mode, Stationary and Pump
in Motion (Pressure Gauge in Cab
Included)

PUMPING MODE
An interlock system will be provided to ensure that the pump drive system components are properly engaged so that the apparatus can be safely operated. The interlock system will be designed to allow stationary pumping and the truck to be in motion while pumping.

A digital pump pressure gauge will be supplied in the cab. 26 771
Bid #:

0535276
Pump Shift, PTO Pump

PUMP SHIFT
A pump shift will be provided within easy reach of the driver for engagement of the PTO driven pump. The shift will include the indicator lights as mandated by NFPA. The pump shift control will be illuminated to meet NFPA requirements.
0581602
Transmission Lock-up, Not Req'd,
PTO Pump
0004547
Auxiliary Cooling System

AUXILIARY COOLING SYSTEM
A supplementary heat exchange cooling system will be provided to allow the use of water from the discharge side of the pump for cooling the engine water. The heat exchanger will be a separate unit. It will be installed in the pump or engine compartment with the control located on the pump operator's control panel. The exchanger will be plumbed to the master drain valve. 0014486
Not Required, Transfer Valve, Single
Stage Pump
0746511
Valve, Relief Intake, TFT

INTAKE RELIEF VALVE
A Task Force Tips A
18 series relief valve will be installed on the suction side of the pump preset at
125
psig
.

The relief valve will have a working range of
90 psi to
300
psi.

The pressure relief valve control will be located behind an access door at the right side pump panel.

The outlet will terminate below the frame rails with a

2.50 " National Standard hose thread adapter
and will have a "do not cap" warning tag.
0794959
Controller, Pressure, Pierce, Pump
Boss, PBA300

PRESSURE CONTROLLER
A Pierce Pump Boss Model PBA
300
pressure governor will be provided.

A pressure transducer will be installed in the water discharge manifold on the pump.

The display panel will be located at the pump operator's panel. 0613850
Primer, Waterous, VPO Motor, (1)
VAP Valve, (2) Push Button Controls,
PTO Pump

PRIMER SYSTEM
A Waterous electric pump priming system conforming to standards outlined in the current edition of NFPA
1901
shall be furnished with the apparatus.

One (
1 ) VPO electric motor driven rotary vane primer shall be provided.

One (
1 ) VAP vacuum activated priming valve shall be plumbed to the main pump.

Two (
2 ) momentary push-button controls shall be provided, with one located at the pump operator's panel for the main pump and one located in the cab.

The push button control system control shall operate an electric priming motor and the priming valve shall automatically open during priming and close when the primer is deactivated. 0506633
Plate, Test, Main Pump

TEST PLATE
A main pump test plate will be provided at the left pump operator's panel that states the rated discharges and pressures as determined by the pump certification test. 0694360
Pump Drain, Trident Multi-Port, IPO
Std Pump Drain

PUMP DRAIN
A Trident multi port pump drain will be used in place of the standard pump drain. 0517155
Line, 0.375" Recirculating w/Check
Valve, Automatic, NFPA 1906,
Wildland

RECIRCULATING LINE, WITH CHECK VALVE
A

0.375
" automatic recirculating line will be run from the discharge side of the main pump to the water tank. This line will be designed to circulate water continuously from the pump back to the tank to help maintain the water pump temperature at a safe level. The recirculating line will be plumbed into the water tank dome. The recirculation line will include a check valve to facilitate priming and prevent water backflow. The check valve will be installed as close as possible to the water tank dome.
0759034
Outlet, Back Pack Pump Filler,
Gravity Fed From Tank, BX3

BACK PACK PUMP FILLER VALVE
A brass,

0.75 " quarter turn ball valve with a chrome handle will be supplied for the refill of back pumps. This outlet is gravity fed from the main water tank sump. The valve plumbing will be

0.75 "
I.D. Aeroquip type hose with swivel fittings. It will be routed to allow smooth flow of water from the tank sump to the valve.

The valve outlet will be installed at the rear of the truck below the rear compartment. A

0.75 " male
garden hose fitting will be provided to allow the connection of a piece of garden hose as needed to fill back pumps, etc.

A manual shut off valve will be provided at the tank.
27 771
Bid #:

0640352
Thermal Relief Valve, OPM, w/Red
Warning Light and Audible Alarm,
Darley Pump

THERMAL RELIEF VALVE
A Waterous Overheat Protection Manager (OPM) will be included on the pump that monitors pump water temperature and opens to relieve water to cool the pump when the temperature of the pump water exceeds
140
Degrees F (
60 C) and a red warning light that is triggered when the water in the pump reaches
180
F (
82 C).

The warning light will act as an additional protection device if the temperature in the pump keeps rising after the valve opens. The warning light and audible alarm with a test switch will be mounted on the pump operator panel.

The discharge line will be plumbed to
ground
.
0780364
Manuals, Pump, (2) Total, Electronic
Copies

PUMP MANUALS
There will be a total of two (
2 ) pump manuals provided by the pump manufacturer and furnished with the apparatus. The manuals will be provided by the pump manufacturer in the form of two ( 2 )
electronic copies. Each manual will cover pump operation, maintenance, and parts. 0602487
Plumbing, Stainless Steel and Hose,
Single Stage Pump, PMFD

PLUMBING, STAINLESS STEEL AND HOSE
All inlet and outlet lines will be plumbed with either stainless steel pipe, flexible polypropylene tubing or synthetic rubber hose reinforced with hi-tensile polyester braid. All hose's will be equipped with brass or stainless steel couplings. All stainless steel hard plumbing will be a minimum of a schedule
10 wall thickness.

Where vibration or chassis flexing may damage or loosen piping or where a coupling is required for servicing, the piping will be equipped with victaulic or rubber couplings.

Plumbing manifold bodies will be ductile cast iron or stainless steel.

All piping lines are to be drained through a master drain valve or will be equipped with individual drain valves. All drain lines will be extended with a hose to drain below the chassis frame.

All water carrying gauge lines will be of flexible polypropylene tubing.

All piping, hose and fittings will have a minimum of a
500
PSI hydrodynamic pressure rating.
0775901
Plumbing and Manifolds, Stainless
Steel, w/Foam System

FOAM SYSTEM PLUMBING
All piping and manifolds that is in contact with the foam concentrate or foam/water solution will be stainless steel. The fittings will be stainless steel or brass. Cast iron pump manifolds will be NOT allowed.
0762334
Inlet, 5.00" - 1000 GPM Pump, Left
Side Only, BX3

MAIN PUMP INLETS
A

5.00 " pump manifold inlet will be provided on the left side of the vehicle. The suction inlet will include removable die cast zinc screens that are designed to provide cathodic protection for the pump, thus reducing corrosion in the pump.
0017541
Cap, Main Pump Inlet, Rocker Lug,

NST, VLH

MAIN PUMP INLET CAP
The main pump inlets will have National Standard Threads with a rocker lug chrome plated cap.

The cap will be the Pierce VLH, which incorporates an exclusive thread design to automatically relieve stored pressure in the line when disconnected.
0084610
Valves, Akron 8000 series- All

VALVES
All ball valves will be Akron® Brass. The Akron valves will be the 8000
series heavy-duty style
with a stainless steel ball and a simple two-seat design. No lubrication or regular maintenance is required on the valve.

Valves will have a
ten (
10 ) year
warranty.
0766918
Valve, Inlet(s) Recess Behind Panel,
Wildland BX3
The location of the valve for the auxiliary inlet(s) will be behind the pump panel. 0004700
Control, Inlet, at Valve

INLET CONTROL
The side auxiliary inlet(s) will incorporate a quarter-turn ball valve with the control located at the inlet valve. The valve operating mechanism will indicate the position of the valve. 0505201
Inlet, Left Side, 2.50", Wildland

LEFT SIDE INLET
There will be one (
1 ) auxiliary inlet with a Akron
8600

2.50 " valve at the left side pump operator's
panel, terminating with a

2.50 " (F) National Standard hose thread adapter.

The auxiliary inlet will be provided with a strainer, chrome swivel and plug.

If the gated inlet intake valve location on the pump panel is higher than the top of the frame rail, a chrome
30 degree inlet with

2.50 " NH (F) swivel will be supplied.
0763478
Inlet, Right Side, 2.50", Auxiliary Inlet,
Wildland BX3, BX

RIGHT SIDE INLET
There will be one (
1 ) auxiliary inlet with a

2.50 " valve at the right side pump panel, terminating
with a

2.50 " (F) National Standard hose thread adapter.

The auxiliary inlet will be provided with a strainer, chrome swivel and plug. 28 771
Bid #:

0505132
Anode, Zinc, Pair, Pump, One (1) on
Inlet Side & One (1) on Discharge
Side

ANODE, INLET
One (
1 ) pair of sacrificial Zinc anodes will be provided in the water pump to protect the pump from corrosion. One (
1 ) will be placed in the inlet side of the pump and the other one ( 1 ) in the
discharge side of the pump.
0723049
Valve, .75" Bleeder, Aux. Side Inlet,
"T" Swing Handle

INLET BLEEDER VALVE
A

0.75 " bleeder valve will be provided for each side gated inlet.

The valves will be located behind the panel with a "T" swing style handle control extended to the outside of the panel.

The handles will be chrome plated and provide a visual indication of valve position. The swing handle will provide an ergonomic position for operating the valve without twisting the wrist and provides excellent leverage.

The water discharged by the bleeders will be routed below the chassis frame rails. 0520031
Tank to Pump,(1) 3.0" Valve,4.0"
Plumbing,In/Open-Out/Closed,
Wildland/BX3

TANK TO PUMP
The booster tank will be connected to the intake side of the pump with

4.00 " heavy duty piping
and a quarter turn

3.00 " full flow line valve with the control remotely located at the operator's panel. Tank to pump line will run straight (no elbows) from the pump into the front face of the water tank and angle down into the tank sump. A rubber coupling will be included in this line to prevent damage from vibration or chassis flexing.

The control on the pump panel will be "in" when the valve is open and "out" when the valve is closed.

A check valve will be provided in the tank to pump supply line to prevent the possibility of "back filling" the water tank.
0006764
Tank ReFill, 2.0"

TANK FILL
A

2.00 " combination tank refill and pump re-circulation line will be provided, using a quarter-turn full flow ball valve controlled from the pump operator's panel. 0021138
Control, Outlets, At Valve, NFPA
1906 Wildland

DISCHARGE OUTLET CONTROLS
The discharge outlets will incorporate a quarter-turn ball valve with the control located at the valve. The valve operating mechanism (handle) will indicate the position (open/closed) of the valve.
0768275
Outlet, Left Side, 2.50", w/1000 GPM
Pump, Wildland

LEFT SIDE DISCHARGE OUTLETS
A quantity of
One (
1 ) discharge outlet
will be provided on the left side pump operator's panel.

Each outlet valve will be a

2.50 " quarter turn full flow ball valve with a TS-style handle. 0015027
Not Required, Elbow, Left Side
Outlets
0759639
Outlet, Left Side, 2.50" w/2"
Plumbing, Adjacent to Deadlay,
Wildland BX3
There will be
One (1) discharge outlet
with a 2.00" valve on the left side of the apparatus,
adjacent the deadlays, terminating with a male 2.50" National Standard hose thread adapter. In addition, the discharge will be equipped with a 2.50" (F) x 1.50" (M) NST reducer. 0035094
Not Required, Elbow, Left Side
Outlets, Additional
0024302
Not Required, Outlet, Right Side,
Wildland
0065478
Not Required, Elbow, Right Side
Outlets
0759637
Outlet, Right Side, 2.50" w/2"
Plumbing, Adjacent to Deadlay,
Wildland BX3

RIGHT SIDE DISCHARGE OUTLET(S)
There will be
One (
1 ) discharge outlet
with a

2.00 " valve on the right side of the apparatus,
adjacent the deadlays, terminating with a male

2.50 " National Standard hose thread adapter. In
addition, the discharge will be equipped with a

2.50 " (F) x

1.50 " (M) NST reducer.
0089584
Not Required, Elbow, Right Side
Outlets, Additional
29 771
Bid #:

0773401
Outlets,(2),Front1.5"w/2" Plumbing,
Valves at Outlet,LS-RS,1906
Wildland BX3

FRONT DISCHARGES
There will be two (
2 )

1.50 " discharges at the front bumper, located
one (
1 ) each side
.

Plumbing will be a single line to the front bumper and will include a tee that supplies both discharges. Plumbing will consist of

2.00 " piping and flexible hose with two (
2 )

2.00 " self-locking
one-quarter turn full flow ball valve with "TSC" style handles. Control of each outlet will be at the valve at the front bumper. Installed on the outlets will be 90 degree swivels with

1.50 " NPSH
thread
and chrome caps and chains.

There will be
Petcock quarter turn
drains provided at all low points of the piping.

The valves for each front bumper hose basket will be located outboard of the frame rail and mounted below the bumper deck.

The discharge swivel locations will provide adequate clearance for the use of

1.50 " gated wye's
and be designed so as not to interfere with the opening and closing of the hood. The swivels will feature stops to protect the hood.

An emergency shut off valve will be provided for this plumbing line in case of damage. The valve will be in an accessible location on the right side of the apparatus near the pump module. This valve will be labeled "Front Discharge On/Off".
0505191
Outlet, Rear, 1.50", w/2" Plumbing,
Valve at Outlet, Wildland BX3

REAR DISCHARGE VALVE
A quantity of
One (
1 ) discharge outlet
with a

2.00 " valve will be provided. The valve will be a

2.00 "
full flow ball valve controlled at the valve body, and will have a

1.50 " NH male thread adapter with
chrome cap and chain. It will be installed with proper clearance for spanner wrenches or adapters.

The valve will be exterior mounted below the
center
hose bed.
0045099
Not Required, Elbow, Rear Outlets

0766836
Outlet, Rear, 2.50", Wildland BX3
DISCHARGE OUTLET (Rear)
There will be
One (
1 ) discharge outlet
piped to the rear of the truck, located on the
center
. Proper
clearance will be provided for spanner wrenches or adapters. Plumbing will consist of

2.50 " piping
along with a

2.50 " full flow ball valve with the control at the valve.

The discharge outlet(s) will terminate with a

2.50 " male National Standard hose thread male
adapter.
0655198
Not Required, Elbow, Rear Outlets,

2.50", Additional
0752097
Caps/Plugs for 1.00" to 3.00"
Discharges/Inlets, Chain

DISCHARGE CAPS/ INLET PLUGS
Chrome plated, rocker lug, caps with chain will be furnished for all discharge outlets

1.00 " thru

3.00 " in size, besides the pre-connected hose outlets.

Chrome plated, rocker lug, plugs with chain will be furnished for all auxiliary inlets

1.00 " thru

3.00 "
in size.

The caps and plugs will incorporate a thread design to automatically relieve stored pressure in the line when disconnected.
0891588
Valve, 0.75" Bleeder, Discharges,
BX3

OUTLET DRAINS/BLEEDERS
A .
75 ", quarter turn type bleeder valve will be provided for each

1.50 " or larger discharge except
the deluge and the front bumper discharge (if equipped).

Bleeders for the discharges at the pump panels will be located adjacent to their respective discharge. They will be properly labeled identifying the discharge they are plumbed into. These valve(s) will be supplied with a "T" swing handle.

Bleeders for rear discharges will be located at the rear of the apparatus, adjacent to their respective discharge. They will be properly labeled identifying the discharge they are plumbed into. These valve(s) will be supplied with a rectangular "T" style handle.

The water discharged by the bleeders will be routed below the chassis frame rails. 0758532
SP
Deadlay (1), No Plumbing, Low
Mount, 200' of 1.75" Capacity, NO
Divider, BX3

DEADLAY HOSE BED
One (
1 ) deadlay bed
, without plumbing, will be provided at the top/front of the pump compartment. It will be capable of carrying a total of
200
' of

1.75 " double jacketed fire hose.

The deadlay bed flooring will consist of perforated brushed aluminum.

The deadlay will be recess mounted at the front of the pump module to provide optimum accessibility.
0766784
Hose Restraint,Treadplate Top, Vinyl
Sides, Wildland BX3

CROSSLAY HOSE RESTRAINT
An aluminum treadplate cover, hinged at the
front
will be installed over the top of the deadlay. It
will include a latch at each end of the cover to hold it securely in place, and a foam rubber gasket where the cover comes into contact with a painted surface.

CROSSLAY END FLAPS
A
red
vinyl end flap will be provided over each end of the hose bed. The flaps will be permanently attached to the aluminum cover, and secured with velcro and snaps on the bottom. 30 771
Bid #:

0766783
NPSH Reel, Booster, LS, 2/3 H.P.

Motor, Over Pump, Wildland BX3

BOOSTER HOSE REEL ABOVE PUMP
One Hannay electric rewind booster hose reel with
2/3
HP motor will be installed over the pump
compartment, on the left side of the apparatus. The exterior finish of the reel will be painted job
color matching the body exterior
.

A polished stainless steel roller and guide assembly will be mounted on the reel side of the apparatus. An additional roller assembly will be installed on the side of the truck opposite the reel for use with hose payout to the right side.

Discharge control will be provided at the pump operator's panel. Plumbing to the reel will consist of

1.00 " hose and piping with a

1.00 " valve.

The reel will have NPSH threaded couplings.
0005280
Switches, Reel Rewind - (1) Each
Pump Panel
Reel motor will be protected from overload with a circuit breaker rated to match the motor.

Two (
2 ) electric rewind control switches will be provided, one ( 1 ) installed on each pump panel.
0018394
Hose, Booster - 150' of 1.00"/800
PSI, 1" NPSH Coupling

Booster hose,

1.00 " diameter and
150
feet, with chrome plated Barway, or equal couplings will be provided. The couplings will have
1 " NPSH threads.

Working pressure of the booster hose will be a minimum of 800
psi.
0017858
Capacity, Hose Reel 150' of 1"

Capacity of the hose reel will be 150 feet of 1.00" booster hose. 0007428
Nozzle for Booster Reel Not Req'd

0759765
Foam Sys, FoamPro1600 (Single
Agent), Wildland BX3

FOAM SYSTEM
There will be a Hypro/Foam Pro, Model
1600
, direct injection foam proportioning system
furnished and installed on the apparatus.

The system will be a single agent system suitable for handling Class "A" foam concentrate only.

The foam system will be plumbed to all valved discharges

2.0 " and smaller, which includes the
following discharges: Front bumper outlets (would include turret discharge if so equipped), rear

1.50 " discharge, right and left side discharges adjacent to the deadlays (used to pre-connect hose in deadlay) and the hose reel(s).

The proportioning operation will be based on an accurate direct measurement of water flows with no water flow restriction. The foam system will be installed in accordance with the manufacturer recommendations.

The system will be equipped with a control module. It will be installed at the pump operator's panel and enable the pump operator (primary use during pump in stationary motion mode) to perform the following functions:

Activate the foam system.

Change foam concentrate proportioning rates from .
1 percent to
1 percent.

Flash a low concentrate warning light when the foam concentrate tank runs low of concentrate and in two (
2 minutes if foam concentrate is not added to tank shut the foam pump down.

A remote on/off switch will be provided in the cab. It will enable the driver to activate the foam system for use while in pump in motion mode. Changing the concentrate proportioning rates will require stopping the vehicle and making the adjustment at the main control installed on the pump operator's panel.

The foam system will have a
12 volt,
1/3
hp electric motor driven positive displacement piston type foam concentrate pump with a rated capacity of .
01 to

1.6 gpm with operating pressures up to
400
psi.

A full flow check valve will be provided in the discharge piping to prevent foam contamination of the fire pump and water tank.

A
5 psi opening pressure check valve will be installed in the concentrate line. 0012126
Not Required, CAF Compressor

0552661
Foam Refill, Pump, Wildland

FOAM REFILL PUMP
A
12 v pump will be permanently mounted in the pump compartment. A male quick disconnect fitting will be provided accessible to the pump operator and a pick-up wand with a 6 ' tube and
mating female fitting will be provided loose.

The pump will be plumbed to the foam tank allowing the user to refill the foam tank from the ground.
0031896
Demonstration, Foam System, Dealer
Provided
0768342
Foam Tank, Separate 20 Gallon, BX3

FOAM TANK
The foam tank will be separate from the polypropylene water tank. The tank will have a capacity of
20 gallons of foam with the intended use of
Class A foam
. The brand of foam stored in this
tank will be a nationally recognized brand. This tank will not reduce the capacity of the water tank.

A screen and breather will be included in the fill dome and lid. 0628071
Drain, 1.00", Foam Tank #1, Foam
System, Quarter Turn, BX

FOAM TANK DRAIN
The foam tank drain will be a

1.00 " quarter turn drain valve located inside the pump/plumbing compartment.
31 771
Bid #:

0738072
Approval Dwg, Pump Panel(s), Not
Required
0035570
Pump Panel Configuration, No Match
Required

PUMP PANEL CONFIGURATION
The pump panel configuration will be neat and orderly.
0762017
Material, Pump Panels, Brushed
Stainless, 1906 Wildland BX3

PUMP AND GAUGE PANEL
The pump panels will be constructed of stainless steel with a brushed finish. 0766517
Pump Access - Wildland BX3

PUMP ACCESS
Access to the pump & plumbing will be provided through a removable panel installed on the back wall of the right side forward compartment.

Access will also be via a hinged panel installed at the pump operator's position, and from the area above the pump.
0071130
Light, Pump Compt, PMFD

PUMP COMPARTMENT LIGHT
A compartment light will be provided inside the pump enclosure. 0586382
Gauges, Engine, Included With
Pressure Controller

Engine monitoring graduated LED indicators will be incorporated with the pressure controller.

Also provided at the pump panel will be the following:
- Master Pump Drain Control
0005601
Throttle, Engine, Incl'd w/Press
Controller
0739224
Indicator Light @ Pump Panel,
Throttle Ready, Incl w/Pressure
Gov/Throttle,Green

THROTTLE READY GREEN INDICATOR LIGHT
There will be a green indicator light integrated with the pressure governor and/or engine throttle installed on the pump operators panel that is activated when the pump is in throttle ready mode. 0549333
Indicators, Engine, Included with
Pressure Controller
0745568
Indicator Light, Pump Panel, Ok To
Pump, Green

OK TO PUMP INDICATOR LIGHT
There will be a green indicator light installed on the pump operators panel that is activated when the pump is in Ok To Pump mode.
0787146
Control, Air Horn At Pump Panel
w/Red Button, BX

AIR HORN BUTTON
An air horn control button will be provided at the pump operator's control panel. This button will be red in color and properly labeled and put within easy reach of the operator. 0511078
Gauges, 4.00" Master, Class 1, 30"-0
-600psi

VACUUM AND PRESSURE GAUGES
The pump vacuum and pressure gauges will be liquid filled and manufactured by Class 1 Incorporated ©.

The gauges will be a minimum of

4.00 " in diameter and will have white faces with black lettering, with a pressure range of

30.00 "-
0-600#
.

Gauge construction will include a Zytel nylon case with adhesive mounting gasket and threaded retaining nut.

The pump pressure and vacuum gauges will be installed adjacent to each other at the pump operator's control panel.

Test port connections will be provided at the pump operator's panel. One will be connected to the intake side of the pump, and the other to the discharge manifold of the pump. They will have

0.25 in. standard pipe thread connections and non-corrosive polished stainless steel or brass plugs.

They will be marked with a label.

This gauge will include a
10 year warranty against leakage, pointer defect, and defective bourdon tube.
0759686
Discharge Pressure Gauges
Required, w/1000 gpm Pump

PRESSURE GAUGES
The individual "line" pressure gauges for the discharges will be interlube filled and manufactured by Class
1 ©.

They will be a minimum of

2.00 " in diameter and will have white faces with black lettering.

Gauge construction will include a Zytel nylon case with adhesive mounting gasket and threaded retaining nut.

Gauges will have a pressure range of
30 "-
0-400#
.

The individual pressure gauges shall only be installed for outlets at the pump panels and as close to the outlet control as practical.
32 771
Bid #:

0766488
Gauge,Water and Foam Level,Master
w/Mini in Cab, Wildland BX3/BLM
WATER and FOAM LEVEL GAUGES
An electric water level gauge manufactured by Innovative Controls Inc., the SL Series Tank Level Monitor System will be provided. One (
1 ) master display electric water level gauge will be
provided on the pump operator's panel, and one (
1 ) "mini" slave display electric water level gauge
will be provided in the cab on the console.

A foam level gauge will be integrated into the water level gauge housing.

The master display electric water level gauge will register water level by means of fourteen ( 14 )
brightly colored LED lights and be provided on the pump operator's panel. The water level indicators will be as follows:

Full = Green
3/4
= Yellow
1/2
= Yellow
1/4
= Yellow
Empty = Red
The mini slave display electric water level gauge will register water level by means of five ( 5 )
brightly colored LED lights and be provided in the cab on the console. The water level indicators will be as follows:

Full = Green
3/4
= Yellow
1/2
= Yellow
1/4
= Yellow
Empty = Red
To further alert the pump operator, the refill light will start flashing when the water level drops below the
1/4
mark.

The level measurement will be based on the sensing of the electrical conductivity of the water in the tank.
0668618
Not Required, Foam Level Gauge
Included With Dual Water & Foam
Gauge
0723261
Lighting, Pump Operator Control
Panel Illumination, BX3

LIGHTING, PUMP PANEL ILLUMINATION
Lighting will be provided for the pump operator's control panel. Illumination will be 12 volt DC
white LED lights installed under the cargo extension.

The lighting will illuminate the controls, switches, essential instructions, gauges, and instruments necessary for the operation of the apparatus. These lights will be activated by the pump panel light switch.

One (
1 ) pump panel light will come on when the pump is in ok to pump mode. 0773413
Light, Over PS Pump Panel, P25
LED, Wildland BX3
There will be
one (
1 )
white LED scene lights with ABS chrome housing, installed above the passenger side pump panel.

The lights will be operated from a switch on the pump operator's panel. 0751223
Compartment,Tool/Equipment,Right
Side Pump Module,Angled Door
Opening,BX3

COMPARTMENT, TOOL/EQUIPMENT, PUMP PANEL
A compartment, constructed of aluminum, will be installed by the right side pump panel for storage of long handle tools. The main area of the compartment will be approximately

59.00 " high
(interior) x

14.00 " wide (interior) x

13.75 " deep. A wedge-shaped section located directly behind the door will be able to contain tall/narrow tools.

A vertically hinged door constructed of aluminum will be provided. It will be installed at an angle to maximize the interior space available. It will open
135
degrees for access to the interior. The door
will have a D-ring latch for keeping it closed, and a positive door holder shall be provided to hold the door in an open position.

The interior of the compartment will remain unpainted natural aluminum.

On the inside of the compartment, the back wall toward the pump panel will have a large removable panel to allow access to the pump and plumbing behind it. 0887465
Air Horn, (1) Hadley, Behind Bumper,
on PS Frame Rail, BX3

AIR HORN SYSTEM
One (
1 ) Hadley air horn will be provided and installed behind the front bumper on the passenger side frame rail. The air horn system will be piped to the air brake system wet tank utilizing

0.38 "
tubing. A pressure protection valve will be installed to prevent the loss of air, in the brake system. 0758525
Control, Air Horn, BX3

AIR HORN CONTROL
Control of the air horn(s) will be from the following locations:
a foot switch located on the driver
’
s
side floor and a passenger
’
s side push button
0766263
Siren, Wln 295SLSA1, 100 or 200
Watt, Wildland BX3

ELECTRONIC SIREN
A Whelen®, Model
295
SLSA
1 , electronic siren with noise canceling microphone will be provided.

This siren to be active when the battery switch is on and that emergency master switch is on. 0637494
Location, Electronic Siren, BX
Product
Siren head will be located in the cab within reach of the driver. 33 771
Bid #:

0076157
Control, Elec Siren, Horn Ring

SIREN CONTROL
The electronic siren will be controllable on the siren head and horn ring only. No foot switches will be required.

The driver will have the option to control the siren or the chassis horns from the horn button by means of a selector switch located on the instrument panel. 0766262
Speaker, (1) Wln, SA315P, 100 watt,
Wildland BX3

SPEAKER
There will be
one (
1 ) speaker
provided. Each speaker will be a Whelen model SA
315
P black
nylon composite,
100
-watt. Each speaker will be
connected to the siren amplifier
. A grille to
protect the speaker during off-road use will be integrated into the bumper. 0763428
Location, Speaker, Frt Bumper,
Recessed, Far Left Side on Angled
Corner
The speaker will be recessed in the far left side of the front bumper, in the swept-back section. 0737515
Sw, Siren Brake, Momentary Red,
Switch Panel, Commercial Chassis,
PMFD
A momentary red switch will be included in the cab on the switch panel to activate the siren brake 0758512
Lightbar, Wln, Justice, LED, 4-R, 2-
W, 2-SR, 4-RC, Clear Lens, BX3

LIGHTBAR
There will be one (
1 )

56.00 " Whelen, Model Justice LED lightbar mounted on the cab roof.

This lightbar will include the following:

Four (
4 ) red flashing forward facing LED modules.

Two (
2 ) red steady burn forward facing LED modules.

Two (
2 ) clear flashing forward facing LED modules.

Two (
2 ) red flashing front corner LED modules.

Two (
2 ) red flashing rear corner LED modules.

There will be a switch located in the cab on the switch panel to control the lightbar.

All lenses will be clear.

All white warning lights will be disabled when the parking brake is set. 0754979
SP
Lights, Front Zone, Wln M6** LED,
COLORED Lens, BX3

FRONT WARNING LIGHT
There will be two (
2 ) Whelen, Model M
6 ** LED flashing lights provided at the front of the truck.

The
driver's side front warning light to be red
.

The
passenger's side front warning light to be red
.

The color of the lenses will be
warning light lens colors to be the same as the LEDs
.

The lights will be mounted with
with a flange
.

The lights will be activated by a switch on the cab instrument panel. 0627989
Flasher, Headlight Alternating,
Commercial Chassis, BX

HEADLIGHT FLASHER
The high beam headlights will flash alternately between the left and right side.

There will be a switch installed in the cab on the switch panel to control the high beam flash. This switch will be live when the battery switch and the emergency master switches are on.

The flashing will automatically cancel when
the hi-beam headlight switch is activated
or when the
parking brake is set.
0754978
SP
Lights, Side Zone Lower, Wln M6*C
LED, COLORED Lens 2pr, BX3

SIDE ZONE LOWER LIGHTING
There will be four (
4 ) Whelen®, Model M
6 *C, flashing LED warning lights with chrome trim
installed per the following:

Two (
2 ) lights,
one (
1 ) each side on the bumper extension
. The
side front lights to be red
.

Two (
2 ) lights,
one (
1 ) each side on the rear corners of the body
. The
side rear lights to be red
.

The lights will include
warning light lens colors to be the same as the LEDs
.

There will be a switch in the cab on the switch panel to control the lights.

The lights on the front bumper will be recess mounted to better protect them from damage. 0754976
SP
Lights, Rear Zn Lwr, Wln M6*,
COLORED Lens, For Tail Light
Housing, BX3

REAR ZONE LOWER LIGHTING
There will be two (
2 ) Whelen®, Model M
6 *, LED flashing warning lights will be located at the rear of the apparatus.

The
driver's side rear light to be red
The
passenger's side rear light to be red
Both lights will include
warning light lens colors to be the same as the LEDs
.

There will be a switch located in the cab on the switch panel to control the lights. 0754975
SP
Lights, Rear/Side Up Zone, Wln
M6*C LED, COLORED Lens 4lts,
BX3
WARNING LIGHTS (Rear and Side upper zones)
Four (
4 ) Whelen, model M
6 *C LED flashing warning lights will be provided at the rear of the apparatus.

The
side rear upper light(s) on the driver's side to be red .

The
rear upper light(s) on the driver's side to be red
.

The
rear upper light(s) on the passenger's side to be red
.

The
side rear upper light(s) on the passenger's side to be red .

These lights will include
warning light lens colors to be the same as the LEDs
.

There will be a switch located in the cab on the switch panel to control the lights. 34 771
Bid #:

0006551
Not Required, Lights, Rear Upper
Zone Blocking
0746901
SP
Light, Traffic Directing, Wln TAM65
36" Long LED, Wildland BX3, BX

TRAFFIC DIRECTING LIGHT
There will be one (
1 ) Whelen®, Model TAM
65 ,

36.00 " long x

2.87 " high x

2.25 " deep, amber LED
traffic directing light installed at the rear of the apparatus.

The Whelen, Model TACTL
5 , control head will be included with this installation.

The controller will be energized when the battery switch is on.

The
with the emergency master switch
.
0627993
Location, Traf Dir Lt, Surface Mount,
BX
This traffic directing light will be surface mounted at the rear of the apparatus as high as practical. 0627991
Location, Traf Dir Lt Controller, in
Cab, Within Reach of Driver, Comm,
BX
The traffic directing light controller will be located inside the cab within easy reach of the driver. 0758774
SP
Receptacle, 15/20A 120V 3-Pr 3-Wr,
NEMA 5-20R SB Dup, 1st, Interior
Body, BX3
120

VOLT RECEPTACLE
There will be
one (
1 )
,
15/20
amp
120
volt AC three (
3 ) wire straight blade duplex receptacle(s)
with
an interior stainless steel wall plate
, installed
RS
2 . The NEMA configuration for the
receptacle(s) will be
5-20
R.

The receptacle(s) will be powered from the
shoreline inlet
.

There will be a label installed near the receptacle(s) that state the following:

Line Voltage
Current Ratting (amps)
Phase
Frequency
0007150
Bag of Nuts and Bolts

LOOSE EQUIPMENT
The following equipment will be furnished with the completed unit:

One (
1 ) bag
of chrome, stainless steel, or cadmium plated screws, nuts, bolts and washers, as used in the construction of the unit.
0519913
Not Required, Soft Suction Hose

SOFT SUCTION HOSE
There will be no soft suction hose provided.
0766675
Strainer, Provided by Dealer,
Wildland NFPA 1906 2016
Classification

STRAINER PROVIDED BY FIRE DEPARTMENT
NFPA
1906
,
2016
edition, section

16.2.4.1 references a suction strainer used with suction hose.

The strainer is not on the apparatus as manufactured. The dealer will provide the suction strainer. 0766687
Extinguisher, Dry Chemical, Wildland,
NFPA 1906 2016, Provided by Dealer

DRY CHEMICAL EXTINGUISHER PROVIDED BY DEALER
NFPA
1906
,
2016
edition, section

5.7.2 requires one (
1 ) approved dry chemical portable fire
extinguisher with a minimum
3 A-
40 -B:C rating mounted in a bracket fastened to the apparatus.

The extinguisher is not on the apparatus as manufactured. The dealer will provide and mount the extinguisher.
0766685
Extinguisher, 2.5 Gal, Not Required,
NFPA 1906 2016 Wildland Apparatus

35 771
Bid #:

0607712
Paint Process / Environmental
Requirements, PMFD

PAINT PROCESS
The exterior custom cab and/or body painting procedure will consist of a seven ( 7 ) step finishing
process. A commercial chassis paint process will follow similar processes as determined by the chassis manufacturer. The following procedure will be used by Pierce:

Manual Surface Preparation
- All exposed metal surfaces on the custom cab and body will be thoroughly cleaned and prepared for painting. Imperfections on the exterior surfaces will be removed and sanded to a smooth finish. Exterior seams will be sealed before painting. Exterior surfaces that will not be painted include; chrome plating, polished stainless steel, anodized aluminum and bright aluminum treadplate.

Chemical Cleaning and Pretreatment
- All surfaces will be chemically cleaned to remove dirt, oil, grease, and metal oxides to ensure the subsequent coatings bond well. The aluminum surfaces will be properly cleaned and treated using a high pressure, high temperature 4 step Acid Etch
process. The steel and stainless surfaces will be properly cleaned and treated using a high temperature
3 step process specifically designed for steel or stainless. The chemical treatment converts the metal surface to a passive condition to help prevent corrosion. A final pure water rinse will be applied to all metal surfaces.

Surfacer Primer
- The Surfacer Primer will be applied to a chemically treated metal surface to provide a strong corrosion protective base coat. A minimum thickness of 2 mils of Surfacer Primer
is applied to surfaces that require a critical aesthetic finish. The surfacer primer will be a two- component high solids urethane that has excellent sanding properties and an extra smooth finish when sanded.

Finish Sanding
- The surfacer primer will be sanded with a fine grit abrasive to achieve an ultra- smooth finish. This sanding process is critical to produce the smooth mirror like finish in the topcoat.

Sealer Primer
- The sealer primer is applied prior to the base coat in all areas that have not been previously primed with the surfacer primer. The sealer primer is a two-component high solids urethane that goes on smooth and provides excellent gloss hold out when top coated.

Base
coat Paint
- Two coats of a high performance, two component high solids polyurethane base coat will be applied. The Base coat will be applied to a thickness that will achieve the proper color match. The Base coat will be used in conjunction with a urethane clear coat to provide protection from the environment.

Clear Coat
- Two (
2 ) coats of clear coat will be applied over the base coat color. The clear coat is a two-component high solids urethane that provides superior gloss and durability to the exterior surfaces. Lap style doors will be clear coated to match the body. Paint warranty for the roll-up doors will be provided by the roll-up door manufacturer.

Our specifications are written to define cyclic corrosion testing, physical strengths, durability and minimum appearance requirements must be met in order for an exterior paint finish to be considered acceptable as a quality finish.

Each batch of base coat color will be checked for a proper match before painting of the cab and the body. After the cab and body are painted, the color is verified again to make sure that it matches the color standard. Electronic color measuring equipment will be used to compare the color sample to the color standard entered into the computer. Color specifications are used to determine the color match. A Delta E reading will be used to determine a good color match within each family color.

All removable items such as brackets, compartment doors, door hinges, and trim will be removed and separately if required, to ensure paint behind all mounted items. Body assemblies that cannot be finish painted after assembly will be finish painted before assembly.

Environmental Impact
Contractor will meet or exceed all current State regulations concerning paint operations. Pollution control will include measures to protect the atmosphere, water and soil. Controls will include the following conditions:

Topcoats and primers will be chrome and lead free.

Metal treatment chemicals will be chrome free. The wastewater generated in the metal treatment process will be treated on-site to remove any other heavy metals.

Particulate emission collection from sanding operations will have a

99.99 percent efficiency
factor.

Particulate emissions from painting operations will be collected by a dry filter or water wash process. If the dry filter is used, it will have an efficiency rating of 98 percent. Water wash
systems will be

99.97 percent efficient.

Water from water wash booths will be reused. Solids will be removed on a continual basis to keep the water clean.

Paint wastes will be disposed of in an environmentally safe manner.

Empty metal paint containers will be recycled to recover the metal.

Solvents used in clean-up operations will be recycled on-site or sent off-site for distillation and returned for reuse.

Additionally, the finished apparatus will not be manufactured with or contain products that have ozone depleting substances. Pierce will, upon demand, present evidence that the manufacturing facility meets the above conditions and that it is in compliance with the state EPA rules and regulations.
0583864
Paint by Pierce, Any Color,
Commercial Chassis, 4-Door, PMFD

PAINT
To ensure a perfect color match between the body and chassis, the apparatus manufacturer will also repaint the commercial chassis cab. The apparatus will be painted #356
Red
.
0586532
Chassis Paint, Order BLACK for
Repaint by Pierce

COMMERCIAL CHASSIS REPAINT
In order to assure a perfect match between the chassis cab and the rest of the apparatus, or to provide the specified color not typically available from a commercial chassis manufacturer, the chassis cab will be repainted by the apparatus manufacturer.

Since it is not practical to repaint certain areas of the cab such as the fire wall, radiator core support, or bottom of the cab, the best results will be obtained by ordering the commercial chassis painted a neutral color.
36 771
Bid #:

0673553
Paint, 2-Tone by PIERCE, Special
COLOR, Special Paint BREAK, 4-
Door Cab

TWO-TONE CAB
The cab will be painted two-tone by the apparatus manufacturer. The top portion of the cab will be painted
#20
White
to match the purchaser's photograph or design.
0582663
Paint, Chassis Frame Assy, Black, by
Commerical Chassis Manufacturer

PAINT CHASSIS FRAME ASSEMBLY
The chassis frame assembly shall be painted black by the chassis manufacturer. It shall remain the commercial grade finish as provided.
0651184
Paint, Wheels, By Pierce,
Commercial 4x2/4x4

WHEEL PAINT
The exterior surface of the outside wheels will be painted by Pierce to assure a color match to the main color of the cab. The exterior visible areas of the wheel will be painted with the same processes and quality of materials used on the apparatus exterior. 0651181
Wheels, Silver Accent Stripe on
Outer Edge, Single Axle

WHEELS, ACCENT STRIPE
The exposed outer edge circumference of the wheel will be painted with a silver accent stripe. 0736826
SP
Coating, Durabak, Top/Bottom
Flange, Front Bumper

FRONT BUMPER COATING
Durabak
™
coating will be provided on the outside exterior of the top and bottom front bumper flanges. It will not be applied on the inside of the flanges.

The material will be
textured black
.
0744291
SP
Paint, Storage Compt Door(s), Main
Body Color

PAINTED EQUIPMENT STORAGE DOOR(S)
A quantity of
six (
6 )
storage compartment doors will be painted instead of the finish as described in the storage area option.

The following equipment storage doors will be painted the same color as the main portion of the body/cab:
the four (
4 ) fender compartments on the body and (
2 ) lower body compartments
0581434
Transit Coating, Carwell, Corrosion
Protection, Including Underside

TRANSIT COATING
All non-painted metal surfaces on the exterior of the vehicle will be sprayed with a corrosion protective coating provided by Carwell. The coating can be removed with soap and water.

The coating is made of a linseed oil base and is biodegradable.

The underside non-painted metal surfaces will also be coated with a corrosion protective coating. 0037234
Compartment, Unpainted

COMPARTMENT INTERIOR FINISH
The interior of the body compartments will be left unpainted and have the natural finish. 0544124
Reflective Band, 1"-4"-1"

REFLECTIVE STRIPES
Three (
3 ) reflective stripes will be provided across the front of the vehicle and along the sides of the body. The reflective band will consist of a

1.00 "
white
stripe at the top with a

1.00 " gap then a

4.00 "
white
stripe with a

1.00 " gap and a

1.00 "
white
stripe on the bottom.
0007357
Reflective on Front Bumper

REFLECTIVE VINYL ON FRONT BUMPER
There will be a reflective vinyl band provided across the front bumper. 0766414
Stripe, Chevron, Rear, Reflexite,
Wildland BX3

REAR CHEVRON STRIPING
There will be alternating chevron striping located on the rear-facing vertical surface of the apparatus. The rear surface, excluding the rear compartment door, will be covered.

The colors will be red and
L
2 fluorescent yellow green
.

Each stripe will be

6.00 " in width.

This will meet the requirements of the current edition of NFPA 1906
, which states that
50%
of the
rear surface will be covered with chevron striping.
0027341
Jog, In Reflective Stripe, Single or
Multiple

JOG(S) IN REFLECTIVE BAND
The reflective band located on each side of the apparatus body will contain one (
1 )
jog(s) and will
be angled at approximately a
45 degrees when installed.
0567374
Stripe, Black Outline each Chevron
Stripe @ Rear (Not Warranted)

REFLECTIVE STRIPE OUTLINE
A black vinyl outline will be provided for each chevron stripe at the rear of the truck. 0065785
Stripe, Reflective, Cab Drs Interior,
Commercial Cabs, 4dr

CAB DOORS REFLECTIVE STRIPE
A
white
reflective stripe will be provided on the interior of each cab door.

This stripe will be a minimum of

96.00 square inches and will meet the NFPA
1901
requirement.
0027286
Not Required, Lettering Specs
37 771
Bid #:

0007472
[Lettering not Requested]

0683995
Lettering, Vinyl, 24.00", Each

LETTERING
There will be non-reflective vinyl lettering,

24.00 " high, with
no outline or shade
provided. There
will be
three (
3 ) letters
provided.
0684031
Lettering, Vinyl, 6.00", Each

LETTERING
There will be non-reflective vinyl lettering,

6.00 " high, with
no outline or shade
provided. There
will be
ten (
10 ) letters
provided.
0685985
Lettering, Reflective, 12.00", Each

LETTERING
There will be reflective lettering,

12.00 " high, with
outline and shade
provided. There will be
three
(
3 ) letters
provided.
0685992
Lettering, Reflective, 10.00", (1-20)

LETTERING
One (
1 ) to twenty (
20 ) reflective lettering,

10.00 " high, with
no outline or shade
will be provided.
0686011
Lettering, Reflective, 6.00", (1-20)

LETTERING
One (
1 ) to twenty (
20 ) reflective lettering,

6.00 " high, with
outline and shade
will be provided.
0686018
Lettering, Reflective, 5.00", Each

LETTERING
There will be reflective lettering,

5.00 " high, with
outline and shade
provided. There will be
six (
6 )
letters
provided.
0686041
Lettering, Reflective, 2.00", (1-20)

LETTERING
One (
1 ) to twenty (
20 ) reflective lettering,

2.00 " high, with
no outline or shade
will be provided.
0686081
Lettering, Reflective, 3.00", (21-40)

LETTERING
Twenty-one (
21 ) to forty (
40 ) reflective lettering,

3.00 " high, with
outline and shade
will be
provided.
0686082
Lettering, Reflective, 3.00", (1-20)

LETTERING
One (
1 ) to twenty (
20 ) reflective lettering,

3.00 " high, with
no outline or shade
will be provided.
0037227
Lettering, Reflective, Reverse Cut
Into Reflective Band

REFLECTIVE LETTERING
ten (
10 ) letters
,

2.00 "
high will be cut into the reflective stripe to allow the painted surface to form the letter. The letters will be
inside the
4 " white reflective stripe. located on both the front cab doors forward in the stripe, see job
#35534
for reference
.
0017273
Emblem, Maltese Cross, Gold Leaf,
12"-14", Pair

MALTESE CROSS INSTALLATION
There will be
one (
1 )
pair of Maltese crosses, comprised of genuine gold leaf material, provided and installed
one (
1 ) each side front cab door
.
0766245
Manual, Fire Apparatus Parts, USB,
Body Parts Only, Commercial
Product

MANUAL, BODY PARTS ONLY
A custom parts manual for the Pierce® installed parts only will be provided in USB flash drive format with the completed unit.

The manual will contain the following:
- Job number
- Part numbers with full descriptions
- Table of contents
- Parts section sorted in functional groups reflecting a major system, component, or assembly - Parts section sorted in Alphabetical order
- Instructions on how to locate parts
The manual will be specifically written for the body model being purchased. It will not be a generic manual for a multitude of different bodies.

SERVICE PARTS INTERNET SITE
The service parts information included in this manual are also available on the Pierce website.

The website offers additional functions and features not contained in this manual, such as digital photographs and line drawings of select items. The website also features electronic search tools to assist in locating parts quickly.
38 771
Bid #:

0766243
Manual on USB Flash Drive, Service,
Commercial

MANUALS, SERVICE
A USB flash drive format service manual supplement containing parts and service information on Pierce® installed components will be provided with the completed unit.

The manual will be specifically written for the unit being purchased. It will not be a generic manual for a multitude of different units.
0002902
Manual, Commercial Chassis
Operation

MANUAL, CHASSIS OPERATION
One (
1 ) chassis operation manual will be provided with the completed unit. 0080008
Warranty, Basic, 1 Year, Apparatus,
Commercial Chassis, WA0008

ONE (
1 ) YEAR MATERIAL AND WORKMANSHIP
Each new piece of apparatus will be provided with a minimum one ( 1 ) year basic apparatus
material and workmanship limited warranty. The warranty will cover such portions of the apparatus built by the manufacturer as being free from defects in material and workmanship that would arise under normal use and service.

A copy of the warranty certificate will be submitted with the bid package. 0761945
Warranty, Basic Vehicle, 1 yr,
International HV (w/Cummins Engine)

CHASSIS WARRANTY
The basis chassis warranty will be for a total of
one (
1 ) year exclusive of miles/kilometers.
0595813
Warranty, Paint, 10 Year, Cab, Pro-
Rate, WA0055
TEN (
10 ) YEAR PRO-RATED PAINT AND CORROSION
A Pierce cab limited pro-rated paint warranty certificate, WA 0055
, is included with this proposal.
0695416
Warranty, Pierce Camera System,
WA0188

CAMERA SYSTEM WARRANTY
A Pierce fifty four (
54 ) month
warranty will be provided for the camera system
.
0647720
Warranty, Pierce LED Strip Lights,
WA0203

COMPARTMENT LIGHT WARRANTY
The Pierce
12 volt DC LED strip lights limited warranty certificate, WA 0203
, is included with this
proposal.
0021516
Warranty, 5-Year EVS Transmission,
Standard Comm, WA0187

TRANSMISSION WARRANTY
The transmission will have a
five (
5 ) year/unlimited mileage
warranty covering
100
percent
parts and labor. The warranty to be provided by Allison Transmission and not apparatus builder. 0688798
Warranty, Water Tank, Lifetime, UPF,
Poly Tank, WA0195

WATER TANK WARRANTY
A UPF poly water tank limited warranty certificate, WA
0195
, is included with this proposal.
0596025
Warranty, Structure, 10 Year, Body,
WA0009
TEN (
10 ) YEAR STRUCTURAL INTEGRITY
The Pierce apparatus body limited warranty certificate, WA 0009
, is included with this proposal.
0690936
Warranty, Roll up Doors, Not
Required

0582368
Warranty, Pump, Darley, 6 Year
Parts, 3 Year Labor, WA0179

PUMP WARRANTY
A Darley pump limited warranty certificate, WA
0179
, is included with this proposal.
0648675
Warranty, 10 Year S/S Pumbing,
WA0035
TEN (
10 ) YEAR PUMP PLUMBING WARRANTY
The Pierce apparatus plumbing limited warranty certificate, WA 0035
, is included with this
proposal.
0641372
Warranty, Foam System, Not
Available
0595820
Warranty, Paint, 10 Year, Body, Pro-
Rate, WA0057
TEN (
10 ) YEAR PRO-RATED PAINT AND CORROSION
A Pierce body limited pro-rated paint warranty certificate, WA 0057
, is included with this proposal.
0593921
Not Required, Warranty, No Lettering

0544883
Certification, Cab Integrity, IHC,
CD0025

CAB INTEGRITY
The cab has been tested to and passed the following standards:
- ECE Regulation No.
29 - SAE J
2422
Cab Roof Strength Evaluation - Quasi-Static Loading Heavy Trucks. 39 771
Bid #:

0545073
Amp Draw Report, NFPA Current
Edition

AMP DRAW REPORT
The bidder will provide, at the time of bid and delivery, an itemized print out of the expected amp draw of the entire vehicle's electrical system.

The manufacturer of the apparatus will provide the following:

Documentation of the electrical system performance tests.

A written load analysis, which will include the following:

The nameplate rating of the alternator.

The alternator rating under the conditions specified per:

Applicable NFPA
1901
or
1906
(Current Edition).

The minimum continuous load of each component that is specified per:

Applicable NFPA
1901
or
1906
(Current Edition).

Additional loads that, when added to the minimum continuous load, determine the total connected load.

Each individual intermittent load.

All of the above listed items will be provided by the bidder per the applicable NFPA 1901
or
1906

(Current Edition).
0002758
Amp Draw, NFPA/ULC Radio
Allowance

0000017

FLORIDA DIVISION BODY

0000015

FLORIDA DIVISION COMMERCIAL

CHASSIS
0004713

ENGINE, OTHER
0046395
EVS 3000 Series TRANSMISSION
0018574

DARLEY PUMP

0028048

FOAM SYSTEM
0020006

SIDE CONTROL
0020007

AKRON VALVES

0020909
ABS SYSTEMS, Commercial

0658751

PUMPER BASE

40 771
Bid #:

Turning Performance Analysis
Bid Number:
771
Chassis:

International HV, 4x4, Wildland BX3
Department:

City of Sacramento Fire Department
Body:

WILDLAND BX3, Type 3, NFPA 1906
Parameters:
*Inside Cramp Angle:
0°
Axle Track:

0.00 in.

Wheel Offset:

0.00 in.

Tread Width:

0.00 in.

Chassis Overhang:

0.00 in.

Additional Bumper Depth:
19 in.

Front Overhang:

0.00 in.

Wheelbase:
183 in.

Calculated Turning Radii:

Inside Turn:
0 ft. 0 in.

Curb to curb:
0 ft. 0 in.

Wall to wall:
0 ft. 0 in.

Notes:
*Actual Inside cramp angle may be less than shown.

Curb to Curb turning radius calculated for 9.00 inch curb. 05/24/2022
Category
Option
Description
Bumpers
0751239
Bumper Extension, 19", Steel Painted, Chicago Style, Commercial Chassis, BX3

Definitions:

Inside CrampAngle
Maximum turning angle of the front inside fire.

Axle Track
King-pin to King-pin distance of front axle.

Wheel Offset
Offset from the center line of the wheel to the King-pin.

Tread Width
Width of the tire tread.

Chassis Overhang
Distance of the center line of the front axle to the front edge of the cab. This does not include the bumper depth.

Additional Bumper Wheel
Depth that the bumper assembly adds to the front overhang.

Wheelbase
Distance between the center lines of the vehicles front and rear axles.

Inside Turning Radius
Radius of the smallest circle around which the vehicle can turn.

Curb to Curb Turning Radius
Radius of the smallest circle around which the vehicle's tires can turn. This measures assumes a curb height of 9 inches.

Wall to Wall Turning Radius
Radius of the smallest circle around which the vehicle's tires can turn. This measures takes into account any front overhang due to chassis , bumper extensions and or aerial devices.

Option
Description
Type*
Minimum
Load
Intermittent
Load
Total
Connected
0001247
High Idle w/Electronic Engine, Commercial

0.00 1.20

0.00 0005940
Lights, Engine Compt, (2) Commercial Chassis

0.00 3.20

0.00 0071130
Light, Pump Compt, PMFD

0.00 1.80

0.00 0549333
Indicators, Engine, Included with Pressure Controller

0.00 0.35

0.00 0561471
Lights, Backup, Wln M6BUW, LED, For Tail Lt Housing

0.00 3.20

0.00 0589905
Alarm, Back-up Warning, PRECO 1040

0.00 0.50

0.00 0613850
Primer, Waterous, VPO Motor, (1) VAP Valve, (2) Push Button Controls, PTO Pump

0.00 260.00

0.00 0627989
Flasher, Headlight Alternating, Commercial Chassis, BX

0.00 0.00

0.08 0641093
Light, Do not move apparatus, Commercial, BX Program

0.00 0.62

0.00 0725601
Fuel/Water Separator, Racor, Heated, International, BX3

0.00 0.00

0.01 0727421
Winch, Warn, 15000 lb. Fixed, Front, Steel Cable, Polished Fairlead, BX3

0.00 500.00

0.00 0748987
Wiring, Spare, 20 A 12V DC 1st, BX3

0.00 0.00

15.00 0748995
Wiring, Spare, 4.8 A 12V DC, USB Termination Blue Sea 1045 1st, BX3

0.00 0.00

5.00 0752061
Lights,Off Road Driving,HiViz LED,Under Bumper,Fwd Facing and Bumper Corners,BX3

0.00 8.59

0.00 0756891
Wiring, Spare, 60A 12V DC, 12 Circuit Fuse Block, Blue Sea 5026, BX3

0.00 0.00

60.00 0758525
Control, Air Horn, BX3

0.00 0.83

0.00 0758909
Wiring, Spare, 30 A 12V DC, 6 Circuit Fuse Block, Blue Sea 5025 1st, BX3

0.00 0.00

30.00 0759408
Lights, Side Scene, Wln PCPSM1C LED 2nd, RIGHT Side of Body, BX3

0.00 4.20

1.80 0759409
Lights, Side Scene, Wln PCPSM1C LED 1st, LEFT Side of Body, BX3

0.00 4.20

1.80 0759671
Wiring,Spare,4.8 A 12V DC,USB Termination Blue Sea 1045, on Rear of Console, BX3

0.00 0.00

5.00 0759765
Foam Sys, FoamPro1600 (Single Agent), Wildland BX3

0.00 36.00

0.00 0762337
Single Start, (3) Grp 31, 660 CCA each, Ext/Crew Cab, International

0.00 3.00

0.00 0763429
Lights, Walk Surf, Additional Not Req'd, Hose Bed Light Adequate, BX3

0.00 0.00

0.00 0764255
Lights, Rear Scene, Wln, PCPSM1C Pioneer LED Fld/Spt, Surface Mount, BX3, BX

0.00 0.00

12.00 0766783
NPSH Reel, Booster, LS, 2/3 H.P. Motor, Over Pump, Wildland BX3

0.00 36.00

0.00 0767278
Camera w/Guard, Pierce, 7" LCD, Rear Camera Only, BX

0.00 1.20

0.00 0772726
Light, Visor, Wln, 12V PCH2* Pioneer LED Fld/Spt, Brow Mt, Commercial, BX

0.00 0.00

13.00 0773943
Air Conditioning, Commercial

0.00 3.00

0.00 0778548
Light, Map, Federal Littlite, LED, Gooseneck, BX

0.00 0.00

0.10 0787146
Control, Air Horn At Pump Panel w/Red Button, BX

0.00 0.16

0.00 0002758
Amp Draw, NFPA/ULC Radio Allowance
NFPA

5.00 0.00

0.00 0005926
Light, Open Door - Commercial Std
NFPA

0.95 0.00

0.00 0020881
ABS, Anti-Lock Braking System, Commercial
NFPA

0.60 5.40

0.00 0072620
Wiper control, intermittent feature Commercial
NFPA

1.20 4.80

0.00 0586382
Gauges, Engine, Included With Pressure Controller
NFPA

0.30 0.00

0.00 0634181
Load Manager, Inc w/MUX Electrical System , BX Program
NFPA

0.56 0.56

0.00 0637488
Lights, Cab & Crw Cab Acs Stps, LED, 4 Door Cab, BX Product NFPA

0.28 0.28

0.00 0664481
Bracket, License Plate & Light, P25 LED
NFPA

0.07 0.00

0.00 0669538
Lights, Clearance/Marker/ID, Rear, P25 LED 7Lts,
Pumper/Tanker/PUC
NFPA

0.50 0.00

0.00 0723261
Lighting, Pump Operator Control Panel Illumination, BX3 NFPA

3.00 0.00

0.00 0728924
Engine, Cummins L9, 360 hp, IHC HV, BX3
NFPA

6.00 0.00

0.00 0739224
Indicator Light @ Pump Panel, Throttle Ready, Incl w/Pressure Gov/Throttle,Green
NFPA

0.10 0.00

0.00 0745568
Indicator Light, Pump Panel, Ok To Pump, Green
NFPA

0.10 0.00

0.00 0746901
Light, Traffic Directing, Wln TAM65 36" Long LED, Wildland BX3, BX NFPA

1.26 2.52

0.00 0754975
Lights, Rear/Side Up Zone, Wln M6*C LED, COLORED Lens 4lts, BX3 NFPA

4.00 0.00

0.00 0754976
Lights, Rear Zn Lwr, Wln M6*, COLORED Lens, For Tail Light Housing, BX3
NFPA

1.80 2.70

0.00 0754978
Lights, Side Zone Lower, Wln M6*C LED, COLORED Lens 2pr, BX3 NFPA

3.60 5.40

0.00 0754979
Lights, Front Zone, Wln M6** LED, COLORED Lens, BX3
NFPA

1.00 1.00

0.00 0758512
Lightbar, Wln, Justice, LED, 4-R, 2-W, 2-SR, 4-RC, Clear Lens, BX3 NFPA

13.80 0.00

0.00 0762462
Cab, 4-door Crew Cab, International HV, BX3
NFPA

25.32 7.48

24.75 * UDMC = User Defined Mission Critical, LM = User Defined Load Managed, S = Electrical Amperage Supply 1 Electrical Analysis
5/24/2022
Bid #:
771
FX3 Wildland, International, 1000 GPM, SF-3204
Sales Rep:

Organization:

Hansen, Brad
Golden State Fire Apparatus, Inc
Desc:

Job #:

Customer:

City of Sacramento Fire Department

Option
Description
Type*
Minimum
Load
Intermittent
Load
Total
Connected
0762588
Cab Lighting, LED Clearance/Marker/Fender Turn Signals, International HV
NFPA

14.48 7.79

0.00 0764260
Lights, Step, LED, BX3, Prk Brk
NFPA

1.00 0.00

0.00 0766263
Siren, Wln 295SLSA1, 100 or 200 Watt, Wildland BX3
NFPA

1.56 14.06

0.00 0766488
Gauge,Water and Foam Level,Master w/Mini in Cab, Wildland BX3/BLM
NFPA

1.23 0.00

0.00 0766626
Lights, Hose Bed, Cover, Dual LED Light Strips, BX3
NFPA

3.24 0.00

0.00 0766637
Lights, Perimeter Body, Amdor AY-LB-12HW012 LED 2lts, Rear Step, BX3
NFPA

0.18 0.00

0.00 0766933
Lights, Body Compt, Pierce LED, Dual Lt Strips, Each Side of Door, BX3
NFPA

4.50 4.50

0.00 0767028
Lights, Perimeter Cab, Amdor AY-LB-12HW012 LED 4Dr, NFPA 1906 BX3
NFPA

0.72 0.00

0.00 0767050
Lights, Tail, Wln M6BTT* Red LED Stop/Tail & M6T* Amber LED Dir Arw For Hsg, BX3
NFPA

0.83 2.49

0.00 0768315
Steps,(4) Cast Products,Model SP2011-1/(2) Model SP2016-1,Rear Body,Wildland BX3
NFPA

5.76 0.00

0.00 0769559
Lights, Perimeter Pump House, Amdor AY-LB-12HW012 LED 2lts NFPA

0.36 0.00

0.00 0773413
Light, Over PS Pump Panel, P25 LED, Wildland BX3
NFPA

0.25 0.00

0.00 0773634
Fuel Tank, 70 Gallon, Left Side, Aluminum, Commercial
NFPA

0.08 0.00

0.00 0773950
Trans, Automatic, Allison 3000 EVS, w/(2) PTO Provsions, Commercial
NFPA

2.00 2.00

0.00 0773985
Air Dryer, Brake, w/Heater, Commercial
NFPA

4.70 0.00

0.00 0794959
Controller, Pressure, Pierce, Pump Boss, PBA300
NFPA

1.80 0.00

0.00 0607607
Alternator, 325 amp Leece-Neville, International
S

0.00 0.00

0.00 Load Totals:
112.13
929.03
168.54
Minimum Continuous Load
Supply:
168.00
Demand:
112.13
Variance:

55.87 Total Connected Load
Supply:
282.00
Demand:
280.67
Variance:

1.33 Note: Minimum Continous Load is in "Blocking Right of Way" mode.(Reference current edition of NFPA 1901) Note: Intermittent Load items are not factored in on any alternator load comparisons. These items are included on the report for reference only and should be looked at as amp draw exclusion items. (Reference current edition of NFPA 1901) Note: Total Connected Load "Demand" represents Total Connected Load minus any Load Managed items 168.00
282.00
Alternator Output at Idle:

Alternator Output at Governed Speed:
* UDMC = User Defined Mission Critical, LM = User Defined Load Managed, S = Electrical Amperage Supply 2 Electrical Analysis
5/24/2022
Bid #:
771
FX3 Wildland, International, 1000 GPM, SF-3204
Sales Rep:

Organization:

Hansen, Brad
Golden State Fire Apparatus, Inc
Desc:

Job #:

Customer:

City of Sacramento Fire Department

DEALER

SUPPLIED

EQUIPMENT
AND/OR

SERVICES
Bid #769

DEALER SUPPLIED EQUIPMENT and/or SERVICES
The following items and/or services will be provided by Golden State Fire Apparatus Inc. (GSFA) prior to final delivery:

Shut off- 1.5" Elkhart XD 3 free swivel base Etched with SFD Logo Suth off- 2.5" Elkhart XD 1 free swivel base Etched with SFD logo Tip- Combo Elkhart XD 1 Mid-Range150@ 50 Yellow bumper Stainless Teeth Tip- Combo Elkhart XD 2 Mid-Range 150@50 Orange bumper Stainless Teeth Tip- Combo Elkhard XD 1 High-Range 150@50 Orange bumper Stainless Teeth Tip- Smooth Bore Elkhart 187XD 1 7/8"
1"Nozzle Cascade 10921 12 10/30 GPM NPSH thread 1" Ball Shut-off Cascade 40712NPSH 6 NPSH thread

1.5" Nozzle Cascade 10902 6 Ranger 20/60 GPM

1.5" Ball shut-off Cascade 40711 6
Nozzle-Garden 500AN4 DIXON 8 Brass twist nozzle for Pencil line (garden) Axe-Flat Head LN Curtis 36FF-8 1 36" Poslished with fiberglass handle Axe-Pickhead LN Curtis 32PF-6 1
Bag-Hydrant Huskey 82003N11 1 18"
Cutter-Bolt Cascade #40242 1 24" Heavy Duty Cutter-Bolt HKP 0090MC 1 18"
Extinguisher- Water 240 Amerex 1 2 1/4 gal water Extinguisher-DryChem Ansul 434747 1 20# ABC
Flashlight Streamlight 2702 4 w/ charger kit
Foam Pail wrench ZICO UFCW 1
Halligan Paratech 22000680 1 30"
Mallet-Rubber Nupula 10030NUP 1 3lb blow hammer
Pry-Bar Council 120PP 1 100PP IS DISCOUNTINUED - REPLACED BY 51" #120PP Strap-Extinguisher FireHooks CH-312 1
Strap-Marrying LN Curtis MS1 1
Strobe Light Kit: RED HIGH INTENSITY STROBE KIT, 12000 LIGHTMAN Darley SKU: AZ434R 1
Strobe Light Kit: CLEAR HIGH INTENSITY STROBE KIT, 12000 LIGHTMAN Darley SKU: AH02405 2 2 clear lens covers Wrench- Forestry Spanners Cascade 11201 2
Wrench- Spanner/hydrant set Red Head S-148-3 1
Wrench- Storz Spanner Action A-ASLW 2
Wrench-Pipe 5862074118 IRWIN 2 18"
Wrench-Spanner Red Head Style 103 2 bar-way 3/4" - 1" Torx Bit Sets, 1/4; 3/8 in Drive STANLEY P/N 576-89-420 1 Adapater-Air Kolbolt SGY-AIR 33 1 3/8" Auto coupler with plug kit Adapter-Air Kolbolt SGY-AIR 202 1 1/4" steel NPT coupler Hammer Craftsman Craftsman Model #
CMHT51398 1
CRAFTSMAN 20-key Metric and
Sae Hex Key Set Craftsman Craftsman Model #
CMHT26020 1
T SHAPE HEX KEY WITH 1/4" TIP
SIZE J46416 PROTO 1
Hose-Air Kolbolt SGY-AIR 157 1 25' nylon coil
CRAFTSMAN Carbon Steel 3/4-in
Utility Replacement Blade (10-
Pack)
Craftsman Model #
CMHT11700X 1 5pk
CRAFTSMAN 3/4-in 1-Blade
Retractable Utility Knife Craftsman Model #
CMHT10383 1
Pliers-Fence Home Depot 193610CVSMN 1 10" Heavy Duty Grip Pliers-Lineman Craftsman Model #
CMHT81648 1
CRAFTSMAN 7-Piece 12-Point
Metric Ratchet Wrench Set Craftsman Model #
CMMT12059 1
CRAFTSMAN 12-Piece Acetate
Handle Screwdriver Set Craftsman Model #
CMHT65044 1
Tire inlfator with guage Kolbolt SGY-AIR 194 1

BLACK TOOL BOX W /TRAY
11" X 19" X 7" BLACKHAWK P/N 578-
94100B 1
Wrench-Adjustable Craftsman Craftsman Model #
CMMT81622 1 8"
Wrench-Adjustable Craftsman Craftsman Model #
CMMT81624 1 12"
CRAFTSMAN 11-Piece 12-Point
Standard (SAE) Standard
Combination Wrench Set
Craftsman Model #
CMMT12065 1
CRAFTSMAN 11-Piece 12-Point
Metric Standard Combination
Wrench Set
Craftsman Model #
CMMT12064 1
Wrench-Pipe Kobalt Model # 55773 2 Kobalt 18-in Cast Iron Pipe Wrench CRAFTSMAN 7-Piece 12-Point
Standard (SAE) Ratchet Wrench
Set
Craftsman Model #
CMMT12056 1
CRAFTSMAN 11-Piece Metric 3/8-
in Drive 6-point Shallow Socket Set Craftsman Model #CMMT12043 1 CRAFTSMAN 11-Piece Standard
(SAE) 3/8-in Drive 6-point Shallow
Socket Set
Craftsman Model #CMMT12042 1
CRAFTSMAN 11-Piece Metric 1/4-
in Drive 6-point Shallow Socket Set Craftsman Model #CMMT12041 1 CRAFTSMAN 11-Piece Standard
(SAE) 1/4-in Drive 6-point Shallow
Socket Set
Craftsman Model #CMMT12040 1
Wrench-Vice Grip IRWIN Model # IRHT82578 1 10"
Appliance- 2.5" Water Thief Elkhart BG-104A 1
Valve-gate Elkharat X-86A 1
Valve-Piston Intake TaskForce Tip AB3ST-NX 1 6" threaded to 5" Storz Wye- Gated 1.5" x 1.5" TaskForce Tip AYLNFNF 4 Forestry Wye- Gate 2.5" x 1.5" Elkhart B100-A 2
Elbow- 5" Storz x 2 1/2" female SE-50S25NLH 1
Elbow- 5" Storz x 4.5" female Redhead SE-50S45NLH 1 Gaskets- 5" drafting 2
Reducer- 4.5" Female x 2 .5" Male 1
Reducer- 4.5" male x 2.5" female 1 Long handle
Reducer-5" Storz x 2 1/2" female 1
Reducer-5" Storz x 3" female 1
Adapter- 2.5" double female Red Head Style 36 2
Adapter- 2.5" double male Red Head Style 35 2
Elbow- 1.5" 45 degree SE394502AC SO PARK 1 CANNOT LOCATE A SOURCE FOR 30 DEGREE ELBOW Elbow- 2.5" 30 degree elbow 4 Chrome
Reducer-2.5" female x 1.5" male Red Head 3725N15N 3 Non-Chrome Reducer-2.5" female x 1.5" male Red Head Style 37 2 Chrome w/ chain Adapter- 1.5" NH Female x 1.5"
NPSH Male 3715N15P 1
Adapter-1.5" double female Red Head 3515N15N 2
Adapter-1.5" double male Red Head 3615N15N 2
Cap-1.5" HCC2804AC SO PARK 2 Chrome w/ chain Elbow- 1.5" 45 degree SE394502AC SO PARK 1 CANNOT LOCATE A SOURCE FOR 30 DEGREE ELBOW Reducer 1.5" NH female x 1"
NPSH male Red Head 3715N10P 2
Reducer- 1.5" NH Female x 1" NH
male 3715N10N 2
Reducer- 1.5" NH Female x 1"
NPSH Male 3715N10P 4
Adapter- 1" NH female x 1" NPSH
male 3710N10P 3
Cap-1" NH Cap HCC2802AC SO PARK 1 Chrome
Reducer- 1" NH Female x 3/4" 3710N75G 1 garden
Reducer- 1" NPSH Female x 3/4"
male 3710P75G 10 garden
Garden Wye Hose Valve National Firefighter UPD GHYV 3
Shut Off Garden Hose Valve National Firefighter UPD GHV 6 Adapter- 2" Pipe x 1.5" NH 1 Chrome
Gasket- 1" SJ Tail Cascade 12112 10 thinwall
Gasket- 1.5" SJ Tail Cascade 12114 10 thinwall
Gasket- Swivel 1" Cascade 12102 5
Gasket-Swivel 1.5" Cascade 12103 10
Gassket- Swivel 2.5" Cascade 12105 5
Strainer- 3" NH female Kochek # BS30U 1 Hard suction
Tee-Forestry Hose Cascade 11151 16
Hose- 3" x 30' Structural Key DP30-800ECO 1 Red
Hose- 3" x 50 Structural Key DP30-800ECO 16 Red
Hose- 5" x 30' LDH Key DP50-600 1 Yellow
Hose- 3" x 8 ' hard suction Kochek P301-10 3
Hose-1" x 100' Forestry Key SP10-600 10 Yellow
Hose-1.5" x 100' Forestry Key SP15-600 16 Yellow
Hose-1.75" x 50' Structural Key DP18-800-FDNY 6 Yellow
Hose-2 .5" x 50' Structural Key DP25-800ECO 6 Yellow
Hose-Pencil Line National Firefighter MRH 75MOPUP 8
Bag- Mop Up Hose National Firefighter TRT CMG1170 6

9.5 X 1.37 RED HOSE RETAINING
RUBBER BANDS, 13 PER POUND HRRB ARC 1
Box- Pelican Pelican #1450 - Black 1
Drip Torch Cascade 12000 2
Drip Torch-Mounting Bracket National Firefighter DRT 100 2 does not come with bracket only, only comes with torch and bracket
File Handles Nicholson Model # 21522N 6 NO BID
Kobalt 10-in Mill Bastard File Kobalt Model # K10BM 6 Foam-FireAde 2000 FIRES-FA2005 5 5gal pails
Headlamp National Firefighter PTZ-PIXA3 4 Petzel
Pack- Radio Harness Ture North RH6100 4
Pack-Field Pack GSA 8465-00-205-3493 1
Pack-Hosepacks Wolfpack gear Quick Release 6 2-roll droper hose pack Pump- Replacement Liner 181798 INDIAN 4 Replacement Liner w/cap-Indian Chief DBL500 Pump-Back Pack 190351 INDIAN 2 With hand pump
Pump-Ditch Honda WH15x 1
Roller-Forestry Hose Roller w/
bracket Cascade 14042 1
Roller-Hose Handheld National Firefighter SCT 4100 1 Scotty Metro-Pak Strap JS Canvas 2
Tool- Shovels Cascade 40270 1 48" round point
Tool-Combi National Firefighter FTO FSS COMBI 1
Tool-McCloud Cascade 40251 1
Tool-Pulski Cascade 40258 2
Traffic Cones Pack-A-Cone PAC-401-28 1
Web Gear- Day Pack Wolfpack gear DDP-HR-2400-BK 6
Web Gear- Fire Shelter Cascade Fire 500096L 4 Large Fire Shelters with plastic sleeve Web Gear- Hose Clamp Holders Wolfpack gear HCT-HR-3106-BK 4 Web Gear- Water Bottle Holder Wolfpack gear VTB-HE-3108-BK 8 Web Gear- Wildland Wolfpack gear SG6210 Ture North 4
Web Gear-Fireline Pack GSA 8465-01-503-4484 1
Wrench-Foam Zico UFCW 1
Bag-Tool Huskey 82177N17 1 15"
Bar, 25" Rollomatic ES 3/8" Stihl 3003-000-4030 1 Bliss Power Lawn Equipment Co Bar Cover National Firefighter True North TNG SB20 1 20" Bar Cover National Firefighter True North TNG SB24 1 24" Bottles- Cap National Firefighter MSR 29129 3
Bottles- Fuel National Firefighter MSR 11831 1 20 oz Bottles-Fuel National Firefighter MSR 11832 2 30 oz Chain, 3/8" 20" Stihl 3672 005 0072 6
Chain, 3/8" 25" Stihl 3672 005 0084 6
Chain Saw Stihl MS462R 20" RESCUE SAW 1
Chaps Stihl #0000-886-3201 2
Container-Fuel mix / bar oil

BRIGGS &

STRATTON
CUSTOM
93261 BRIGGS & STRATTON

METAL GAS/
OIL COMBO CAN 1.5
GALLON OF GAS / 2.5

QUARTS BAR &

CHAIN OIL
1 Faller Axe Sthil Pro Universal Forestry Axe 1
Wedges-Feller 3 10"
Wedges-Feller 3 6"
Ice Chest Yeti TUNDRA 35 HARD COOLER 1
TIE-DOWN KIT for Ice Chest Yeti TIE-DOWN KIT 1
Cots Coleman Trailhead II 4
Inverter Homedepot MRI3011BU 1
Book- FOG Manual FIRESCOPE 420-1 1
GPS- Handheld Garmin 010-02258-20 1 GPSMAP 64csx
Binoculars Pherlna ASIN B07DWXL8GD 1 20x50
Belt Weather Kit FIRE WEATHER INSTRUMENT
KIT 89088 JIM-GEM 1
Clipboard Galls CP033SIL 1
Flagging-"3 Stripe" CHEVSP1 HARRIS 12 Red/white stripe Flagging-Hazard 1-3/16" X 300' BLACK/YELLOW
STRIPE VST-12 HARRIS 12
Flagging-Killer Tree PRESCO CUSTOM 12
Flagging-Lime Green 1-3/16" X 150' FLUORESCENT
GREEN VST-22 HARRIS 12
Flagging-Orange 1-3/16 X 150' FLUORESCENT
ORANGE VST-18 HARRIS 12
Flagging-Pink 1-3/16" X 150' FLUORESCENT
PINK VST-17 HARRIS 12
Flagging-Spot Fire VST-17 HARRIS 12 Pink
Glow Sticks GREEN 12 HOUR 6"
CHEMLIGHT, 10 PER 9-42290 CYALUME 6
HANDHELD LED SPOTLIGHT SL-2000 ULTIMATE WILD
RECHARGEABLE 1 NO BID
30' Master Pull Super Yanker 1 1/4
rated @ 52,000 TRB114030 1
ARB Ultra Lite Snatch Block rated
@ 38,500 Break Strength 1
ARB 16' Tree trunk protector rated
@ 12,000 kg - 26,500 lbs 1
50’ Master Pull Super Line 10mm
winch extension rope DBE-10-050-SE 1
12' Peerless 3/8 Grade 100 chain
with Grab hooks C38015H 1
ARB Recovery Damper 1
3/4 Screw Pin Shackles Van Beest
62,000 lb. rating G-4161-34 8
Craftsman 18 in. Large Mouth Bag
with Tool Wall 1
Bracket- Bolt Cutter Zico 3095-155-000 1
Bracket- Z-Hook, Axes, Etc Fire Hooks Unlimited HB-1 1 Mount- Chainsaw Zico QM-CSM-L 1
Mount- Coupling Mount 1.5" Zico CM 1.5 2
Nozzle Cup- 1" Booster Line Zephyr 95 1
Plate- Mounting 1.5" Akron 350 4
Plate-Mounting 1" SOUTH PARK 4 NSPH
Radio 800 MHZ Motorola APX6500 1
Radio VHF BK KNGM150-R Remote
Mount Mobile Radio 1
Battery Charger: portable radio
battery charger
AT4-2066IFD 4 bank
conditioning charger for
APX6000 NiCad/NiMH
batteries w/ heavy duty wiring
harness for installation on
vehicle
1 KNG-P150CMD Command
Version, Digital APCO P25 VHF
136-174 MHZ, 5000 Channels, 6
Watt, Full Keypad - RELM BK
Portable Radio
BENDIX KING HHKNGVHREDKC 4 49er Communications
18 Inch Whip BigBoost Antenna,
ANKNGWPBB18V - 211.00 VHF
148-174 MHz, SMA Male
Connector, 2.1dB Gain
for RELM BK Radio KNG P150 and
Midland Radio STP105B
BENDIX KING ANKNGWPBB18V 4 49er Communications
Orange "AA" Clamshell,
BAKNGCSBAO BENDIX KING BAKNGCSBAO 4 Equivalent to KAA0120 for RELM BK Radio KNG Ruggedized Miner Mic,
AAKNGSPMMR3 - IP56 (Driven
Rain
BENDIX KING AAKNGSPMMR3 4 Equivalent to Speaker Mic KAA0204-35 for RELM BK Radio KNG P Series

INTERCOM SYSTEM
The following David Clark components will be provided by the sales organization and installed per the direction of SFD prior to final delivery:
• One (1) Master Station model DC-U3800
• Two (2) Dual Radio Interface /Headset Station model DC-U3816 • One (1) Power Cord model DC-C3820
• Four (4) Interface Cord model DC-C3821
• Two (2) Jumper Cord model DC-C3812
• Four (4) Headset model DC-H3442

TWO WAY RADIO INSTALLATION
There will be two (2) two-way radios installed per the direction of SFD by the sales organization prior to final delivery.

TWO WAY RADIO SPEAKER INSTALLATION
There will be two (2) two-way radio speakers installed per the direction of SFD by the sales organization prior to final delivery.

PORTABLE RADIO CHARGER BANK INSTALLATION
There will be one (1) portable radio charger bank installed per the direction of SFD by the sales organization prior to final delivery.

LOOSE EQUIPMENT INSTALLATION
A loose equipment mounting allowance of $10,890.00 is included in the bid price to cover the cost of mounting the applicable equipment per the direction of the City of Sacramento. If the City of Sacramento exceeds the loose equipment mounting allowance, additional work can be performed at the current published shop rate.

END OF PROPOSAL

PRODUCT

WARRANTIES
Exhibit “C”
Bid #771

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

No specific exclusions apply
Conditions and
Exclusions:

Fire and Rescue Apparatus
Coverage:

One (1) Year Material and Workmanship
Basic Apparatus
Twelve (12) months.Warranty Period
Ends After:

The date the apparatus is placed in service, or 60 days from the original buyer invoice date, whichever comes first.Warranty Begins:

Portions of the apparatus manufactured by Pierce shall be free from defects in material and workmanship
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

3. BUYER'S EXCLUSIVE REMEDY.

CTS-2025A
Printed in the USA Page 1 of 2 CTS-2025A 07/01/ 2017

BASIC VEHICLE COVERAGE Months Miles/Km
(000)
Basic Vehicle Warranty (See exceptions listed below)
Towing (First 90 days see below) (Vehicle Down Situations Only) (See exceptions listed below)
12 3

Unlimited
Unlimited

Note: Items not listed in warranty exceptions follow base warranty.

WARRANTY EXCEPTIONS
CHASSIS COVERAGE Months Miles/Km
(000)
Frame side rails
Cab/cowl structure
Cab/cowl perforation corrosion
84 60
60 Unlimited
Unlimited
Unlimited
DRIVETRAIN COVERAGE Months Miles/Km
(000)
Spicer axles, Propeller shaft, Eaton clutch, TTC Transmission Eaton/Fuller Transmission
Meritor Axles

24 24
24 Unlimited
Unlimited
Unlimited
MISCELLANEOUS COVERAGE Months Miles/Km
(000)
Batteries
Brightwork, Chassis Paint and Corrosion (other than Cab) Hood/Cab Paint
12 6
12 Unlimited
Unlimited
Unlimited
FIRST 90 DAYS FROM DELIVERY TO USER (DTU)
Correction of loose fasteners, squeaks, rattles and unusual noises. Towing (unless specific coverage is stated above).

Adjustments and Maintenance (such as aim headlights, adjust brakes/clutch, adjust steering system, check and fill coolant levels).

LIMITED WARRANTY FOR HV MODELS
HV507 & HV607
*Effective with vehicles built July 01, 2017 or later

BASIC VEHICLE

Navistar, Inc., at its option, will repair or replace any part of this vehicle that proves defective in material or workmanship, in normal use and service, with new or ReNEWed® parts, based on the Component Coverages below. Exceptions are listed below:

WHAT IS NOT INCLUDED UNDER BASIC COVERAGE
Components/Items
• Components warranted by their respective manufacturers (such as, non-International® brand engines, tires, Allison Transmissions, lubricants, etc.) • Bodies, equipment, and accessories installed by other than authorized International® Truck employees at International® Truck manufacturing plants
• Front and rear axle alignment
• Front & Rear axle coverage excludes brakes, wheel ends, axle shafts, controls & attachments.

Repairs & Maintenance
• Maintenance-related items/repairs, or those needed as a result of normal wear and tear, including tune-ups, brake/clutch linings, windshield wiper blades, tire balancing, lubrication, and other similar procedures/parts required to keep vehicle in good working condition
• Failures that are the result of poor fuel quality, water in fuel, rust, etc. • Repairs needed as a result of vehicle misuse, negligent care, improper maintenance, improper operation, or the result of accident or collision • Fade, runs, mismatch or damage to paint, trim items, upholstery, chrome, polished surfaces, etc., resulting from environmental causes such as improper polishes, cleaners or washing solutions, or chemical and industrial fallout
• Failure to observe published capacity or load specifications for engine, transmission, propeller shaft, axles (powertrain) and suspension.

Other
• Vehicles sold and/or operated outside the United States and Canada • This exception does not apply to vehicles that meet current USA EPA emission standards, which were sold by an International dealer located in Mexico, if the vehicle is authorized by the U.S D.O.T to operate in long-haul, cross border transportation and the vehicle is only operated in the United States, Canada, and Mexico • Vehicles/components that have had unauthorized alterations or modifications • Vehicles on which the odometer reading has been altered • Loss of time or use of the vehicle, loss of profits, inconvenience, or other consequential or incidental damages or expenses
• Replacement of defective parts with parts other than those provided by Navistar, Inc CTS-2025A
Printed in the USA Page 2 of 2 CTS-2025A 07/01/ 2017

OBTAINING SERVICE

Return this vehicle to any International Truck Dealer authorized to service this model vehicle and engine.

This warranty is automatically transferred to subsequent owners at no charge. Visit your local Authorized International Truck Dealer for name and address change information.

Note:The customer has 365 days and up to a maximum of 100,000 miles (160,000 km) from DTU to purchase an extended warranty on the unit. For extended warranty purchases between 181 and 365 days from DTU and <100,000 miles (160,000 km) an additional fee will be assessed. See your local International dealer for details.

DISCLAIMER

NO WARRANTIES ARE GIVEN BEYOND THOSE DESCRIBED HEREIN. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED.

THE COMPANY SPECIFICALLY DISCLAIMS WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE, ALL OTHER REPRESENTATIONS TO THE USER/PURCHASER, AND ALL OTHER OBLIGATIONS OR LIABILITIES. THE

COMPANY FURTHER EXCLUDES LIABILITY FOR INCIDENTAL AND
CONSEQUENTIAL DAMAGES, ON THE PART OF THE COMPANY OR SELLER. No person is authorized to give any other warranties or to assume any liabilities on the Company's behalf unless made or assumed in writing by the Company, and no other person is authorized to give any warranties or to assume any liabilities on the seller's behalf unless made or assumed in writing by the seller.

RECORD OF OWNERSHIP

Upon receipt of new vehicle by original owner, complete the following:

I have read this Warranty Brochure and fully understand the warranty coverage. I acknowledge that I have received a copy of the Owner's Limited Warranty and I accept the terms described herein.

Customer Signature Date

Owner’s Address City State/Prov Postal Code

Truck Model Vehicle Identification Number

Engine Number Engine Serial Number

Remedies Under State or Provincial Law: Some States and Provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to the owner. This warranty gives the owner specific legal rights, and he may also have other legal rights which may vary by state or province.

Date Delivered to User (DTU) Odometer Reading at Delivery

IMPORTANT:The information contained in this Warranty Policy explains the coverage provided on your new International® vehicle. This policy should be kept in the vehicle for presentation to the Dealer when you request warranty services.

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

3. BUYER'S EXCLUSIVE REMEDY.

Fire and Rescue Apparatus
Coverage:

Ten (10) Year Pro-Rated Paint and Corrosion
Cab
Ten (10) YearsWarranty Period
Ends After:

The date of the original purchase invoice (issued when the product ships from the factory).Warranty Begins:

Exterior surfaces of the cab painted by Pierce shall be free from blistering, peeling, corrosion or any other adhesion defect caused by defective manufacturing methods or paint material selection.
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This limited warranty is applicable to the vehicle in the following percentage costs of warranty repair, if any:

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4

1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This limited warranty does not apply to related wire
harnesses, cables, and connectors, which are covered by the Pierce one (1) year basic apparatus limited warranty.

Conditions and
Exclusions:

Fire and Rescue Apparatus
Coverage:
54 Months Material and Workmanship
Camera System
Fifty - Four (54) monthsWarranty Period
Ends After:

The date of delivery.Warranty Begins:

This limited warranty covers repairs to correct any defect related to materials or workmanship of the Sharpvision
camera system installed on the apparatus occuring during th e
warranty period.
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

3. BUYER'S EXCLUSIVE REMEDY.

Fire and Rescue Apparatus
Coverage:

Ten (10) Year Material and Workmanship
Pierce 12V LED Strip Light
Limited Warranty
Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:

This limited warranty covers repairs to correct any defect related to materials or workmanship of the Pierce 12V LED strip lights installed on the apparatus occuring during the warranty period.

1. LIMITED WARRANTY
(b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; The date of the original purchase invoice (issued when the product ships from the factory).Warranty Begins:

THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE

TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.

This limited warranty does not apply to related wire
harnesses, cables, and connectors, which are covered by the Pierce one (1) year basic apparatus limited warranty.

Conditions and
Exclusions:

See Also
Paragraphs
2 thru 4

4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,

INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,

WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW

OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY

PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS

THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,

REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.

3. BUYER'S EXCLUSIVE REMEDY.
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce.

Ten (10) YearWarranty Period
Ends After:

Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 7/5/2011 WA0203
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL

OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,

INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.

NEW PRODUCT WARRANTY

PARTICIPATING OEM SALES

DISTRIBUTOR SALES

LIMITED WARRANTY ON NEW ALLISON AUTOMATIC TRANSMISSIONS

USED IN EMERGENCY VEHICLE APPLICATIONS

Allison Transmission will provide for repairs or replacement, at its option, during the warranty period of each new Allison transmission listed below that is installed in an Emergency Vehicle in accordance with the following te rms, conditions, and limitations.

WHAT IS COVERED
 WARRANTY APPLIES — This warranty is for new Allison transmission models listed below installed in an Emergency Vehicle and is provided to the original and any subsequent owner(s) of the vehicle during the warranty period.  REPAIRS COVERED — The warranty covers repairs or replacement, at Allison Transmission’s option, to correct any transmission malfunction resulting from defects in material or workmanship occurring during the warranty period. Needed repairs or replacements will be performed using the method Allison Transmission determines most appropriate under the circumstances.  TOWING — Towing is covered to the nearest Allison Transmission Distributor or authorized Dealer only when necessary to prevent further damage to your transmission.
 PAYMENT TERMS — Warranty repairs, including parts and labor, will be covered per the schedule shown in the chart contained in section “APPLICABLE MODELS, WARRANTY LIMITATIONS, AND ADJUSTMENT SCHEDULE.”  OBTAINING REPAIRS — To obtain warranty repairs, take the vehicle to any Allison Transmission Distributor or authorized Dealer within a reasonable amount of time and request the needed repairs. A reasonable amount of time must be allowed for the Distributor or Dealer to perform necessary repairs.
 TRANSMISSION REMOVAL AND REINSTALLATION — Labor costs for the removal and re-installation of the transmission, when necessary to make a warranty repair, are covered by this warranty.  WARRANTY PERIOD — The warranty period for all coverages shall begin on the date the transmission is delivered to the first retail purchaser, with the following exception:

Demonstration Service - A transmission in a new truck or bus may be demonstrated to a total of 5000 miles (8000 kilometers).

If the vehicle is within this limit when sold to a retail purchaser, the warranty start date is the date of purchase. Normal warranty services are applicable to the demonstrating Dealer. Should the truck or bus be sold to a retail purchaser after these limits are reached, the warranty period will begin on the date the vehicle was first placed in demonstration service and the purchaser will be entitled to the remaining warranty.

APPLICABLE MODELS, WARRANTY LIMITATIONS, AND ADJUSTMENT SCHEDULE

WARRANTY LIMITATIONS
(Whichever occurs first)

ADJUSTMENT CHARGE TO BE

PAID BY THE CUSTOMER APPLICABLE
MODELS
Months
Transmission Miles
Or Kilometers Parts Labor
MT, MD
3000, 3200, 3500, 3700 0–24 No Limit No Charge No Charge HT with Hydraulic Controls 0–24 No Limit No Charge No Charge AT, 1000 Series, 2000 Series,
2400 Series 0–36 No Limit No Charge No Charge
HT with Electronic Controls 0–60 No Limit No Charge No Charge HD
1000 EVS, 2100 EVS, 2200 EVS
2350 EVS, 2500 EVS, 2550 EVS,
3000 EVS, 3500 EVS, 4000,
4000 EVS, 4500, 4500 EVS, 4700,
4700 EVS, 4800, 4800 EVS
0–60 No Limit No Charge No Charge

Page 1 of 2 ends

Sacramento City CouncilJune 21, 2022

Sacramento City Council
June 21, 2022