Adjustment screws are provided on the wear pads to permit proper side alignment.
All sheaves will be plastic and greaseless and all sheave pins and pivot pins will be stainless steel.
ROTATION SYSTEM
A 46.00" diameter, external tooth, monorace, slewing ring bearing will be used for the rotation system. The gear teeth will be a stub tooth form.
The bearing will provide 360 degree continuous rotation.
The turntable will be bolted to the bearing using 36 SAE Grade 8, .875" diameter bolts.
To secure the bearing to the base support 36 Grade 8, .875" diameter bolts will be used.
The turntable base and the torque box bearing plate will be machined to fit the bearing thereby providing even distribution of forces.
A hydraulically driven, planetary gear box with a drive speed reducer will be used to provide infinite and minute rotation control throughout the entire rotational travel.
The gearbox will have a torque rating of 130,000 pounds per square inch.
A spring applied, hydraulically released disc type swing brake will be furnished to provide positive braking of the turntable assembly.
Provisions will be made for auxiliary operation of the system in case of prime mover failure.
The hydraulic system is equipped with pressure relief valves which will limit the rotational torque to a non-destructive power.
ROTATION INTERLOCK
A permanently installed prevention mechanism will be provided as part of the rotation system to prevent the rotation of the aerial device to the side in which the stabilizers have not been fully deployed or are short-jacked.
The mechanism will allow full and unrestricted use of the aerial in the 180 degree area on the side(s) where the stabilizers have been fully deployed.
The system will also have a manual override to comply with NFPA.
LOAD CAPACITIES
The following load capacities will be established with the stabilizers at full horizontal extension and placed in the down position to level the truck and to relieve the weight from the tires and axles. Capacities will be based upon full extension and 360 degree rotation.
A load chart, visible at the operator's station, will be provided. The load chart will show the recommended safe load at any condition of the aerial device's elevation and extension. 50 MPH WIND CONDITIONS/WATERWAY DRY
Degrees of
Elevation
-8 to 9
10 to 19
20 to 29
Bid #: 942 56
30 to 39
40 to 49
50 to 59
60 to 69
70 to 75
Egress
500
500
500
500
500
500
500
500
Fly
-
-
-
-
250
250
750
1000
Upper Mid
-
-
-
250
250
500
1000
1000
Lower Mid
-
-
250
250
500
750
1000
1000
Base
-
250
250
500
750
1000
1000
1000
50 MPH WIND CONDITIONS/WATERWAY CHARGED
Degrees of
Elevation
-8 to 9
10 to 19
20 to 29
30 to 39
40 to 49
50 to 59
60 to 69
70 to 75
Egress
500
500
500
500
500
500
500
500
Fly
-
-
-
-
-
250
500
750
Upper Mid
-
-
-
-
250
500
750
1000
Bid #: 942 57
Lower Mid
-
-
-
250
500
750
1000
1000
Base
-
-
250
500
750
1000
1000
1000
The tip capacity will be reduced to zero when flowing water with the nozzle above the waterway centerline.
BOOM SUPPORT
A heavy-duty boom support will be provided for support of the ladder in the travel position. On the base section of the ladder, a stainless steel scuffplate will be provided where the ladder comes into contact with the boom support. In the stowed position, the ladder tip will be not less than
11.00" below horizontal for unsurpassed visibility and safety while maneuvering the apparatus. 0762413 Light, Boom Support, Amdor AY-LB12HW012, 12" LED AERIAL BOOM SUPPORT LIGHT There will be one (1) Amdor®, Model AY-LB-12HW012, 190 lumen, 12" long, white LED strip light mounted on the boom support cradle. This light will be activated when the aerial master switch is activated.
0755127 Tie Down, Rope, Per Pair, 9000lb
Rating, Trailer Gooseneck, Tiller
ROPE TIE DOWN AT GOOSENECK
There will be two (2) pairs of rope tie downs provided each side of the tiller gooseneck in the forward and rearward locations. Equal quantities will be provided on each side. The tie downs will be rated for a straight line pull of 9000 lb and will be chrome plated. 0619238 SP Cover, Boom Support Wiring, 4Way,
Tiller
COVER FOR BOOM SUPPORT WIRING
The exposed wiring at the rear of the tiller boom support will be covered by an aluminum treadplate cover.
0663833 Boom Support, Raised, Tiller
SPECIAL HEIGHT BOOM SUPPORT
A special height boom support will be provided to raise the aerial device to clear the generator above the gooseneck.
0663892 Scuffplate, Aerial Boom Support, Top
and Sides
BOOM SUPPORT SCUFFPLATES
There will be scuffplates provided on the top and sides of the aerial boom support that come into contact with the aerial device. The scuffplates will be DA finished. 0680821 Boom Panel, Pair
AERIAL BOOM PANEL
There will be one boom panel provided on each side of the aerial ladder base section. The boom panel will be painted #90 red.
The boom panels will be designed so no mounting bolts are in the face of the panel. This will keep the lettering surface free of holes.
0526886 Indicator, Extension, Inside Handrails
Only, Every 10'
EXTENSION INDICATOR
Extension markings and corresponding numerical indicators will be provided along each inside top rail of the base section of the aerial every ten (10) feet. They will indicate various positions of extension up to full. Markings and indicators will be clearly visible to the console operator. To aid in visibility during hours of darkness, the markings and numerical indicators will be of a black reflective material.
0723719 Steps, Folding, Four, Aerial Device,
Trident
FOLDING STEPS
One (1) set of folding steps will be provided at the tip of the ladder. An additional set of folding steps will be provided at the base of the fly section. The steps will be bright finished with a luminescent tread coating, that is rechargeable from any light source and can hold a charge for up to 24 hours, on the stepping surface. Each step will have no integrated light.
Bid #: 942 58
0688232 Rung Covers, Aerial Device
AERIAL DEVICE RUNG COVERS
Each rung will be covered with a secure, heavy-duty, fiberglass pultrusion that incorporates an aggressive, no-slip coating.
The rung covers will be glued to each rung and will be easily replaceable should the rung cover become damaged.
The center portion of each rung cover will be black and the outside 2.00" edge at each side will be photoluminescent to assist in providing a light source for each rung during low light conditions.
Under no circumstances will the rung covers be fastened to the rungs using screws or rivets.
The rung covers will have a 10-year, limited warranty.
0674963 Scabbard, Temporary Vent Saw
Storage, No Depth Gauge, Aerial
Ladder
TEMPORARY SCABBARD AT END OF AERIAL
There will be a total of two (2) vent saw scabbard(s) provided. The scabbard(s) will be mounted on each side of the aerial egress. The scabbard(s) will be DA finished. 0676785 Bracket Only, Rubbish Hook, Aerial
Fly Section
RUBBISH HOOK MOUNTING BRACKET
Mounting will be provided near the end of the fly section of the aerial ladder for a rubbish hook.
The bracket will be sized to hold a Nupla 12' roof vent rubbish hook with D handle. 0678815 Brackets Only, Axe, 6lb or 8lb, Aerial
Fly Section
AXE MOUNTING BRACKETS
Brackets will be provided near the end of the fly section of the aerial ladder for mounting a fire axe. The mounting plates will be D/A finished aluminum. 0663209 Inclinometer, Additional, Aerial Device
ADDITIONAL INCLINOMETER
There will be one (1) additional inclinometer(s) provided to indicate the degree of elevation of the aerial device. The inclinometer(s) will be located on the outside of the base section on the opposite side of the standard location.
A light will be provided to illuminate the inclinometer. 0786841 Brackets Only, Roof/Fresno Ladder,
Base Section, Inboard of Boom Panel
LADDER STORAGE MOUNTING BRACKETS
Mounting will be provided on the right side of the aerial device while viewed from the turntable for storage of one (1) roof ladder(s). The bracket(s) will be located inboard of the boom panel at the base section. The bracket(s) will hold the boom panel as close to the base section as possible and include straps to secure the ladder.
The mounting brackets will accommodate a 10' Duo-Safety 775-DR roof ladder as determined by the type of aerial device and the available space.
0893726 Lights, Turntable Walkway, P25, LED,
Job Color Brackets
LIGHTS FOR TURNTABLE WALKWAY
There will be lights with white LEDs and black housing provided at the aerial turntable. The lights will be located to illuminate the entire walking surface of the turntable including the area around the turntable console. These lights will be activated by the aerial master switch.
The light(s) that are installed with fabricated brackets, the brackets will be painted to match the mounting surface.
0762396 Light, Turntable Console, Amdor AYLB-12HW012, LED Strip Light
TURNTABLE CONSOLE LIGHTING
There will be one (1), Amdor®, Model AY-LB-12HW012, 190 lumen, 12" long, white LED light strip mounted in the turntable console cover to illuminate the controls located on both the upper and lower portion of the turntable control station. These lights will be activated by the aerial master switch.
0660526 SP Hoist Rings, S/S, Forward Edge of
Turntable
HOIST RINGS
There will be two (2) stainless steel hoist rings located on the forward edge (aerial side) of the turntable. One (1) to be mounted on each side of the aerial device.
The hoist rings will be mounted on a stainless steel protective plate which is attached to the turntable deck.
The rating of each hoist ring will be a maximum of 1000 lb. There will be a label indicating this rating provided next to the hoist rings.
0682164 Cover, Around Aerial Rotation
Bearing
ROTATION BEARING COVER
A cover will be fitted over the aerial rotation bearing and drive pinion gear(s). The cover will be aluminum treadplate and attached to the underside of the turntable deck. 0642824 Guard, Aerial Ladder Extension
Control While Stowed, Tiller
LADDER EXTENSION CONTROL GUARD
A guard, fabricated from a stainless steel hinge will be installed at the forward end of the ladder extension control as a protective measure. This will allow the aerial operator at the turntable control console, to position the guard when the ladder is stowed preventing the aerial from extending into the tiller cab window.
Bid #: 942 59
0120788 Control Stations, 100'/105' Tiller
CONTROL STATION
There will be a turntable control station located on the right hand side of the turntable so the operator will be able to easily observe the ladder tip while operating the controls. The controls will permit the operator to regulate the speed of the aerial functions within safe limits (as determined by the manufacturer and NFPA standards). The controls will be clearly marked and lighted for nighttime operation. A hinged aluminum cover will be provided. The momentary foot switch located at the turntable control station will activate the aerial function controls. They are capable of being operated independently or simultaneously.
The following controls and indicator lights will be clearly identified, illuminated, and conveniently located for ease of operation and viewing:
- Elevation, extension/retraction, and rotation controls - High idle switch
- Rung alignment indicator light
- Tip/Tracking lights
- Hydraulic system pressure gauge
- Indicator/Alarm test switch
- EPU switch
- Operator's load chart
- Stabilizer Not Fully Extended indicator light
- Monitor controls
- Aerial waterway flow meter
There will also be a minimum of two (2) 12-volt work lights installed on the turntable to illuminate the surrounding area for nighttime operation. The work lights will be activated by the aerial master switch.
STABILIZER CONTROL STATION
There will be an easily accessible control station located at both the driver and passenger side of the apparatus. The following controls and indicator lights will be clearly identified and conveniently located for ease of operation and viewing at each control station. - Stabilizer controls for driver and passenger side
- Stabilizer Firm On Ground indicator lights
- Stabilizer Fully Extended indicator lights
- Inclinometer for grade and slope
- Stabilizer EPU switch
- High Idle switch
Bid #: 942 60
0662753 Stabilizers, 100'/105' HD Tractor
Drawn Steel Aerial, Split Pan, 17'
Spread
STABILIZERS
The vehicle will come equipped with a stabilization system consisting of two (2) hydraulically operated out and down style stabilizers. This system will meet or exceed all requirements of the NFPA specifications related to stabilization and setup on sloped surfaces.
The stabilizer/leveling jacks will have a maximum spread of 17' measured from the centerline of the jack footpads when the beams are fully extended. The beams will be 6.81" wide x 8.88" high with 0.75" thick top and bottom plates and 0.50" thick sides of 100,000-PSI minimum yield strength steel. The cylinders will have pilot-operated check valves with thermal relief designed to insure that the beams will not drift out of the stowed position during travel. Wear pads will guide the stabilizers.
The horizontal extension cylinders will be totally enclosed within the beams and will incorporate telescoping hydraulic tubing to supply the jack cylinder hydraulic power. Stabilizer hydraulic hoses will remain stationary during operation of the stabilizers to prevent hose wear and potential failure. The cylinders will be equipped with decelerators to reduce the speed of extension and retraction when the beams are near the fully retracted and extended positions. The stabilizer extension hydraulic cylinders will have the following dimensions: 2.25" bore, 1.38" rod, and 57.25" stroke.
The vertical jack cylinders will be capable of 12.00" ground penetration. The cylinders will be supplied with pilot operated check valves on each jack cylinder to hold the cylinder in the stowed or working position, should a charged line be severed at any point in the hydraulic system. For safety, the integral holding valves will be located in the cylinder base end, NOT in the transfer tube. Vertical jack cylinder rods will be fully enclosed by a telescoping inner box to protect the cylinder rods from damage. The stabilizer jack hydraulic cylinders will have the following dimensions: 4.25" bore, 3.00" rod, and 28.88" stroke.
Each stabilizer jack will have a pan that will be of the split-pan design and will be a maximum
12.50" wide so as to allow the extension of the stabilizer between parked cars or other obstacles.
This pan will serve as a protective guard and a mounting surface for warning lights. The top, forward, and rear edges will be flanged back 90 degrees for added strength.
Stabilizer Pads
The stabilizer footpad will be 12.00" in diameter. The footpad will be attached to the jack cylinder rod by means of a machined ball at the end of the jack cylinder rod which mates to a socket machined into the footpad. The footpad will have the ability to pivot 20 degrees from horizontal in any direction to allow setup on uneven terrain.
Auxiliary Stabilizer Pads
An auxiliary ground pad will be supplied for each stabilizer to provide additional load distribution on soft surfaces. The pads will be 24.00" square and made from lightweight composite material.
The ground pressure will not exceed 75 lb per square inch when the ground pads are used and the apparatus is fully loaded and the aerial device is carrying its rated capacity in any position.
There will be one (1) pad located on each side of the apparatus, behind the stabilizers.
Stabilizer Controls
An electrically controlled hydraulic valve will power stabilizer movement. The valve can also be manually controlled in the event of electrical malfunction. Hydraulic power override controls will be incorporated into the valve. The manual override mechanism will be completely sealed within the valve assembly to prevent any possibility of corrosion.
The stabilizer controls will be located to provide the operator with a full view of each stabilizer being positioned. Each stabilizer control panel will include the following:
In/out stabilizer beam control toggle switch
Up/down stabilizer jack control toggle switch
Emergency hydraulic power unit (EPU) control toggle switch High idle control toggle switch
Stabilizer fully extended LED indicator lights
Stabilizer planted LED indicator lights
As a safety device, an electrically actuated diverter valve will be provided. The hydraulic power will be diverted to the aerial ladder controls automatically the instant all stabilizer jacks are firmly planted on the ground. Once the aerial ladder is raised from the bedded position, the stabilizer hydraulic power is cut off so the stabilizers will not accidentally be moved while the aerial is being operated.
To aid in leveling the unit, two (2) bubble type angle indicators will be located near the stabilizer controls. One (1) indicator will show the angle of the truck from the front to rear and the other will show the side to side angle of the truck. The indicators will be color coded green to show when the truck has been properly leveled allowing the aerial device to be operated at full capacity.
A stabilizer deployment audible warning alarm will be provided at each side of the body, activated by the stabilizer movement.
A "Stabilizers Not Stowed" indicator light will be provided in the cab within view of the driver. It will illuminate automatically whenever the stabilizers are not fully stowed to prevent damage to the vehicle if it is moved. The stabilizer system will also be wired to the "Do Not Move Truck" indicator light. This light will flash whenever the apparatus parking brake is not engaged and the stabilizers are not fully stowed.
0728961 Stabilizer Pan Material
STABILIZER PAN MATERIAL
The aerial stabilizer pans will be polished stainless steel. 0530817 Aerial Stabilizer Pins
STABILIZER PINS
The stabilizer jacks will have holes for the stabilizer pins. 0779621 Doors, Stabilizer Control Box,
Valve/Electrical Distribution Box, Tiller
STABILIZER CONTROL BOX DOORS
There will be polished stainless steel doors hinged along the forward edge with a flush lift and turn latch provided over each stabilizer control box.
VALVE/POWER DISTRIBUTION BOX ACCESS DOOR
There will be polished stainless steel doors with a flush lift and turn latch provided over the valve and power distribution box doors. These doors will be bottom hinged.
Bid #: 942 61
0769589 SP Lights, Stabilizer Pad Locator, Wln
Micro MPB*, Rec Stb S Pn, Cnt Ft
STABILIZER GROUND ILLUMINATION LIGHT
There will be two (2) Whelen® Model MPB*, 4,100 lumens 12 volt DC light(s) provided. The light (s) will be recessed in the stationary stabilizer pan(s) located, One (1) DS and One (1) PS.
The light(s) will indicate where the stabilizer pad can be set down.
The painted parts of this light assembly to be black.
The light(s) will be activated when the aerial master switch is activated.
The light(s) may be load managed when the parking brake is applied. 0540495 Pads, Stabilizer, Modified to Slide On STABILIZER PADS, MODIFIED The two (2) auxiliary stabilizer pads will be modified so they can be installed on the bottom of the stabilizer. The auxiliary stabilizer pad holders on the truck will also be modified.
Bid #: 942 62
0121267 Hydraulic System, Tiller
HYDRAULIC SYSTEM
All hose assemblies will be assembled and crimped by the hose manufactures certified technician. An assembly cell will be located on the premises where the technician can perform audits of the final aerial assembly for proper fitting torque and hose routing.
All manufacturing employees responsible for the installation of hydraulic components will be properly trained. Training will include: proper handling, installation, torque requirements, cleanliness and quality control procedures for hydraulic components.
Hoses used in the aerial hydraulic system will be of a premium quality hose with a high abrasion resistant cover. All pressure hoses will have a working pressure of 4000 psi and a burst pressure rating of 16,000 psi.
The hydraulic oil will be a premium Multi-Vis product having a leading edge additive package, provide oxidation stability, be extremely shear stable and maximum anti-wear properties. All oil delivered to the manufacturing site will have a minimum ISO cleanliness level of 18/15/13.
Each aerial will be evaluated as to the region and climate where it will be used to determine the optimum viscosity and proper oil grade. Oil viscosity will be based on an optimum range of 80 to 1000 SUS during normal aerial use. Before shipment of the unit, an oil sample will be taken and analyzed to confirm the oil is within the allowable ISO grade tolerance.
The aerial hydraulic system will have a minimum oil cleanliness level of ISO 18/15/13 based on the ISO 4406:1999 cleanliness standard. Each customer will receive a certificate of actual cleanliness test results and an explanation of the rating system.
Each aerial will include an oil sample port, identified with a yellow dust cap and a label, for subsequent customer testing.
Ball valves will be provided in the hydraulic suction lines to permit component servicing without draining the oil reservoir.
The system hydraulic pressure will be displayed on a 2.5" liquid filled gauge, located on the control console.
The hydraulic system will be additionally protected from excessive pressure by a secondary pressure relief valve set at 3,150 psi. In the event the main hydraulic pump compensator malfunctions, the secondary relief will prevent system damage.
HYDRAULIC CYLINDERS
All cylinders used on the aerial device will be produced by a manufacturer that specializes in the manufacture of hydraulic cylinders.
Each cylinder will include integral safety holding cartridges.
Each cylinder will be designed to a minimum safety factor of 4:1 to failure.
All safety holding cartridges will be installed at the cylinder manufacturer, in a controlled clean environment to avoid possible contamination and or failure.
HYDRAULIC PUMP
The hydraulic system will be supplied by a 4.6 cubic inch variable volume, load and pressure compensating piston pump. The pump will be rated at a minimum of 5,365 psi peak pressure and 2,600 rpm. The pump will meet the demands of all three simultaneous aerial functions. The pump will provide proper flow for single aerial function with the engine at idle speed. A switch will be provided on the control console to increase the engine speed for multiple function operation.
EMERGENCY PUMP
The aerial will be equipped with an emergency hydraulic pump, electrically driven from the truck batteries. The pump will be capable of running for 30 minutes for limited aerial functions to stow the unit in case of a main pump or truck system failure. A momentary switch will be located at the stabilizer and aerial control locations to activate the emergency pump.
AERIAL CONTROL VALVE
The aerial hydraulic control valve will be designed with special spool flows, limiting the oil flow for the designed function speed. The valve will be manually controlled and be located in the control console with the handles protruding through the operating surface for operation. The activation handles will be spaced a minimum of 3.5" for ease of operation. The valve spools will be designed to bleed off downstream pressure, in the neutral position and allow proper seating of any cylinder holding cartridge.
OIL RESERVOIR
The oil reservoir will have a minimum capacity of 40 gallons. The oil fill location will be easily accessible and be labeled "Hydraulic Oil Only" and also indicate the grade of oil that is installed in the reservoir. The fill cap will have a 40 micron filter to provide protection from contamination. A drain hose will be included and will terminate with a quarter turn ball valve.
Two suction ports will be provided, one for the main hydraulic pump and one for the emergency pump. The main suction will be slightly elevated off the bottom of the reservoir and include a 100 mesh suction strainer. The emergency suction port will be closer to the bottom of the reservoir to provide some reserve oil for emergency operation.
A six (6) disc type magnetic drain will also be provided to collect any ferrous contaminants.
A combination sight glass and thermometer will be mounted to the reservoir in an easily viewable location.
HIGH PRESSURE FILTER
The pressure filter will be rated for 6,000 psi working pressure and generously sized for efficiency and capacity. A 90 psi bypass spring will be included to protect the element and hydraulic system during lower than normal system operating temperatures.
The 5Q filter element will be constructed of a micro glass medium, which has the highest capture efficiency, dirt holding capacity and life expectancy over other media such as cellulose and synthetic. The nominal rating will be 5 micron and have an efficiency rating of 99.3 % for 5 micron sized particles. The element will have a dirt holding capacity of not less than 35 grams.
RETURN FILTER
The return filter will be rated for 150 psi working pressure and generously sized for efficiency and capacity. A 25 psi bypass spring will be included to protect the element and hydraulic system during lower than normal system operating temperatures. The 10Q filter element will be constructed of a micro glass medium, which has the highest capture efficiency, dirt holding capacity and life expectancy over other media such as cellulose and synthetic. The nominal rating will be 10 microns and have an efficiency rating of 99.5% for 10 micron sized particles. The element will have a dirt holding capacity of not less than 84.7 grams.
Bid #: 942 63
0120793 Swivels, PAL, Tiller, 32 Collector
Rings
HYDRAULIC SWIVEL
The aerial ladder will be equipped with a high pressure hydraulic swivel which will connect the hydraulic lines from the hydraulic pump and reservoir, through the rotation point, to the aerial control bank. The hydraulic swivel will allow for 360-degree continuous rotation of the aerial.
ELECTRIC SWIVEL
The ladder will be equipped with an electric swivel to allow 360-degree rotation of the aerial while maintaining connections in all electrical circuits through the rotation point. A minimum of 32 collector rings that are capable of supplying 30-amp continuous service will be provided. All collector rings will be enclosed and protected against condensation and corrosion. 0120780 Electrical System, Tiller
ELECTRICAL SYSTEM
The aerial electrical system will be designed and manufactured in such a way that the power and signal protection and control compartments will contain circuit protection devices and power control devices. The power and signal protection and control components will be protected against corrosion, excessive heat, excessive vibration, physical damage, and water spray.
The aerial electrical system will be designed and manufactured to allow the following:
- All of the serviceable components will be readily accessible. - Circuit protection devices will be utilized to protect each circuit. - General protection circuit breakers will be Type-I automatic reset (continuously resetting) or Type-II (manual resetting) and conform to SAE requirements. When required, automotive type fuses conforming to SAE requirements will be utilized to protect electronic equipment. - Power control relays and solenoids, when utilized, will have a direct current (dc) rating of 125% of the maximum current for which the circuit is protected.
The aerial electrical system will be designed and manufactured to allow the following:
- Toggle switches will be utilized that are certified for the outside conditions that fire apparatus experience.
- All wiring will be protected through conduit or loom. - All wiring harnesses will be properly supported to eliminate harness damage through rubbing. - All connectors utilized in the system will be of a waterproof design. - Two (2) inductive proximity switches and an illumination light will be incorporated into the boom support.
- The aerial master and aerial PTO can be engaged after the water pump has been engaged without having to bring the RPM back to idle.
- Standard cabling to the tip of the aerial will consist of one (1) 16/20 cable and one (1) 12/8 cable.
TORQUE BOX POWER DISTRIBUTION PANEL
A fuse and relay panel, located in the passenger side gooseneck area, will include the following:
- NEMA 4x rated weatherproof enclosure
- Relays, fuses, and circuit breakers for aerial and stabilizer interlocks and control switches
TURNTABLE LIGHTING
The turntable will be lighted for nighttime operation with a minimum of two (2) work lights activated by the aerial master switch.
TURNTABLE CONSOLE
The following switches and indicator lights will be standard on the turntable console:
- High idle on/off switch
- Tip/Tracking light switch
- Indicator and alarm test switch
- Emergency hydraulic power switch
- STABILIZERS NOT FULLY EXTENDED amber indicator light
- Rung alignment green indicator light
The turntable console will be lighted for nighttime operation with one (1) work light activated by the aerial master switch. A fuse panel will be located in the turntable console.
TURNTABLE OVERRIDE CONTROLS
The aerial manual override controls will be located in the turntable control console.
MASTER OVERRIDE CONTROLS
An emergency power switch will be located behind an access panel on the driver's side of the tiller gooseneck. The switch will activate the emergency power unit and allow control of the aerial or stabilizers based on the direction the switch is toggled.
A work light will be provided to illuminate the master override controls when the battery switch is active and the master override door is open.
BOOM SUPPORT
Two (2) Turck inductive proximity switches will be provided on the boom support to detect if the aerial device is fully stowed within the boom support.
STABILIZER INDICATOR
A "Stabilizers Not Stowed" indicator will be provided in the driver's compartment. It will illuminate automatically whenever the stabilizers are not fully stowed, to prevent damage to the apparatus if moved. The stabilizer system will also be wired to the "Do Not Move" indicator light, which will flash whenever the apparatus parking brake is not fully engaged and the stabilizers are not fully stowed.
CRADLE INTERLOCK SYSTEM
A cradle interlock system will be provided to prevent the lifting of the aerial from the nested position until the operator has positioned all the stabilizers in a load supporting configuration. A switch will be installed at the cradle to prevent operation of the stabilizers once the aerial has been elevated from the nested position.
STABILIZER ALARM
An electronic warning device will be provided at each stabilizer to warn personnel that the stabilizers are being deployed. Each alarm will produce a fast pulsing 90 DBA signal and will cancel only when the stabilizer is put into a load bearing configuration.
STABILIZER SCENE LIGHTS
A 4.00" clear floodlight will be provided on each stabilizer to illuminate the surrounding area. The light will be actuated by the aerial master switch.
Bid #: 942 64
0804781 Aerial Scene Lts Separated into
Aerial Tip Category and Aerial
Tracking Category
0820601 SP Lights, Tip, Wln MP** LED, 4lts TIP LIGHT
There will be four (4) Whelen® Model MP**, 5,695 lumens 12 volt DC LED lights installed at the tip of the aerial device.
One (1) light on the left side high. The left side tip light to include spot optics.
One (1) light on the left side low. The left side lower tip light to include flood optics.
One (1) light on the right side low. The right side lower tip light to include flood optics.
One (1) light on the right side high. The right side tip light to include spot optics.
The light(s) to be installed with low profile adjustable pedestal mount(s).
The painted parts of this light assembly to be white
The lights will be controlled with the tracking lights. 0802753 Lights, Tracking, Wln MP** LED, 2lts TRACKING LIGHTS There will be two (2) Whelen® MP**, 5,695 lumens 12 volt DC LED lights installed on the base section of the aerial device below the hand rails per the following:
One (1) will be located on the left side with left side tracking light to include spot optics.
One (1) will be located on the right side with spot optics.
The light(s) to be installed with low profile adjustable pedestal mount(s).
The painted parts of this light assembly to be white.
The tracking lights will be controlled by a switch located at the platform/tip and turntable. 0733396 SP Light, Locator, Wln L31H*F, LED, at
Tip, PAL/PAP, 1lt
AERIAL LOCATOR LIGHT
There will be a Whelen®, Model L31H*F, LED beacon installed at the aerial tip for the purpose of locating the aerial device while in operation.
The color of the locator light will be blue.
The lights will be activated whenever the aerial is raised from the cradle. 0618906 Lighting, Rung, LED, TecNiq, 4
Section, Base, Lower/Upper Mid, Fly,
3 Colors RWB
LIGHTING ON AERIAL LADDER
There will be TecNiq, Model D02, LED rung lighting provided on both sides of the aerial ladder base, lower and upper mid, and fly sections. The lighting will be located adjacent to the ladder rungs along the lower rail of the ladder sections and will run the length of the ladder section.
The color of the aerial device when the device is at full extension will be:
Top one-third to be red
Middle one-third to be white
Bottom one-third to be blue
The LED rung lighting will be activated when a switch at the turntable operator's panel is activated through the aerial master and a switch at the turntable operator's panel is activated through the master battery switch.
The lights may be load managed when the parking brake is applied. 0540701 Lights, Stabilizer Warn (1) Set, Wln
M6* LED, Front Colored Lens
STABILIZER WARNING LIGHTS
There will be two (2) Whelen, Model M6*, LED flashing warning lights with Whelen, Model M6FC, chrome flanges installed on the stabilizer cover panels, one (1) each side.
The front stabilizer pan lights will be red LED with a lens the same color as the LEDs.
These warning lights will be activated by the same switch as the side warning lights. 0068703 Lights, Grote Supernova LED,
Stabilizer Beam, (1) Set
STABILIZER BEAM WARNING LIGHTS
Two (2) 4.00" diameter red LED flashing lights will be mounted on each stabilizer, one (1) facing forward and one (1) facing rearward. The lights will be Grote Supernova 40 series LED lights. The lights will be recessed in the horizontal beam of the stabilizer. These warning lights will be activated with the aerial master switch.
0601973 Lights, Stabilizer Scene, (1) set,
Truck-Lite 44042C, LED
STABILIZER SCENE LIGHTS
There will be one (1) Truck-Lite, Model 44042C 4.00" LED, scene light installed under each stabilizer beam to illuminate the surrounding area. A total of two (2) lights will be installed. These lights will be activated by the aerial master switch.
0633833 DC Power To Aerial Tip, 11.2 Amp @
12 Volt DC
DC POWER CABLE to TIP
There will be a cable installed in the aerial device to provide 11.2 amps @ 12 volts DC to the tip of the aerial device.
0737181 Intercom, 2-Way Fire Research
ICA910 Hands Free
2-WAY AERIAL COMMUNICATION SYSTEM
There will be a Fire Research, Model ICA910, two-way intercom system provided. The control module with an LED volume display and push-button volume control will be located on the turntable operator console.
A hands free module will be located at the aerial tip or platform and constantly transmit to the other module unless the control module push-to-talk button is pressed.
Each intercom unit will be weatherproof.
Bid #: 942 65
0540895 Not Required, Breathing Air to Tip,
Aerial Ladder
0024742 Not Required, Mask, Breathing Air To
Tip
0066919 Not Required, Raised Pedestal, Tiller
0597280 Lifting Eye Assembly, Rope Rescue
Attachment, HDL
LIFTING EYE ASSEMBLY - ROPE RESCUE ATTACHMENT
A lifting eye assembly will be provided that is designed to evenly distribute load at the tip of the aerial. The egress will include attachment points for the lifting eye assembly. The lift eye assembly is retained by two (2) locking pins, one (1) at each end outboard side of the egress.
Leveling is maintained by the lifting eye assembly rotating within the egress mounting. 0808215 LyfePulley, Rescue System RESCUE LIFTING SYSTEM A rescue lifting attachment will be provided. The lifting attachmentwill mount to the aerial egress and will consist of a pair of nylatron pulleys mounted to a stainless steel shaft. The pulleys will be adjustable from side to side and will have a total lifting capacity of 750lb, regardless of whether one (1) or both pulleys are being utilized. 0645472 Rope Tie Bar At Base Section, for
Lyfe Pulley, Painted
Box,Ascendant,105',Tiller
ROPE TIE BAR AT BASE SECTION, RESCUE LIFTING SYSTEM
A removable bracket will be supplied at the rear of the base section, attached between the left hand and right hand rear hand rails. The bracket will provide Lyfe Pulley rope tie off and/or guide points spaced 5.75" apart, centered between the rear hand rails. The bracket will be designed to be easily removable and not interfere with a fully retracted ladder assembly when attached to the base section. A storage box for the bracket will be provided on the outside rear of the base section. The storage box and bracket will be painted to match the aerial device. 0667968 Switch, Console Cover, Do Not Move
Truck Indicator Circuit
SWITCH
There will be a switch installed that will activate the Do Not Move Truck Indicator circuit when the battery switch is on, the turntable console cover is opened and the parking brake is released. 0530828 Turntable Access, Chains
AERIAL TURNTABLE CHAIN
A chain will be installed at the aerial turntable.
0090677 Waterway, 100'/105' HDL, Tiller
WATER SYSTEM
A waterway system will be provided consisting of the following components and features:
The integral telescopic water system will consist of a 4.50" diameter tube in the base section, a
4.00" diameter tube in the lower mid-section, a 3.50" diameter tube in the upper mid-section and a 3.00" diameter tube in the fly section. The telescopic waterway will be constructed of anodized aluminum pipe.
The aerial will be capable of discharging up to 1000 gpm at 100 psi parallel to the ladder and 90 degrees to each side of center.
An adjustable pressure relief valve will be furnished to protect the aerial waterway from a pressure surge.
Two (2) 1.50" drain valves will be located at the lowest points of the waterway system and will be routed to drain through the center of the 5th wheel.
WATERWAY SEALS
The waterway seals will be of type-B PolyPak design, composed of nitroxile seal and a nitrile wiper, which together offer maximum stability and extrusion resistance on the waterway. The seal will be capable of withstanding pressures up to 2000 psi, temperatures in excess of 250 degrees Fahrenheit and have resistance to all foam generating solutions. The seals will be internally lubricated.
The waterway seals will have automatic centering guides constructed of synthetic thermalpolymer. The guides will provide positive centering of the extendible sections within each other and the base section to insure longer service life and smoother operation. 0632856 Monitor, Akron 3480 StreamMaster II
Electric
AERIAL MONITOR
An Akron Model 3480 monitor with stow and deploy will be provided at the tip with a Akron 1250 gpm Model 5177.
The monitor's functions will be controlled electrically from two (2) separate locations. One (1) control will be located at the control console and the other at the ladder tip.
There will be a courtesy light at the tip of the aerial to illuminate the controls.
Vertical travel of this monitor will be -45 degrees to 90 degrees. Horizontal rotation will be 90 degrees to each side of the center line of the aerial device. 0534379 Flowmeter, FRC, Waterway, PAL
AERIAL WATERWAY FLOW METER
A Fire Research Corporation Model DF430, digital flow indicator with a four (4) digit LED display will be provided for the aerial waterway at the turntable control station.
The display will have a flow totalizer, programmable high and low flow warnings, and automatically adjust LED brightness for day/night viewing.
Bid #: 942 66
0512000 Inlet, Aerial Waterway, 4.00"
Plumbing with 5.00" Inlet, Tiller
AERIAL WATERWAY INLET
The aerial waterway will be plumbed from the fifth wheel area to the waterway swivel with 4.00" pipe. A 5.00" inlet will be located on each side of the apparatus complete with a chrome plated cap. The individual "line" pressure gauges for the inlets will be manufactured by Class 1. They will be a minimum of 3.50" in diameter and will have white faces with black lettering. Gauges will be compound type with a vacuum/pressure range of 30.00"-0-600#.
The individual pressure gauge will be installed as close to the inlet as practical. 0673128 Quick-Lock Waterway Locking
System, 100' HDL, 105' HDL, ASL
WATERWAY LOCKING SYSTEM
The aerial ladder waterway monitor will be capable of being positioned at either the fly section or at the next lower section of the ladder.
The monitor location will be changeable by the use of a single handle, located at the side of the ladder.
The handle, attached to a cam bracket, will simply be moved forward to lock the monitor at the fly section and back to lock it to the previous section.
There will be no pins to remove and reinstall.
The monitor will be operational at all times, regardless of its position, without connecting or disconnecting electrical lines.
0663185 SP Monitor Auto Stow, To Left Side Body,
Tiller
MONITOR AUTO STOW
The monitor will be set to auto stow facing the left side of the body to the allow the operator to verify the monitor is stowed prior to nesting the device. 0660379 SP Label Pinnable Waterway Lock,
Rescue/Waterpipe
QUICK-LOCK WATER WAY LOCK LABELING
The Quick-Lock waterway locking mechanism will be labeled "LOWER FLY" "RELEASE" "UPPER FLY". Three (3) labels will be installed on the side and three (3) on the top of the pinnable waterway release lever mounting bracket.
0013164 Elbow, Aerial Inlet, 5" FNST x 5"
Storz w/Cap
ADAPTER, STORZ INLET
There will be two (2) 5.00" FNST x 5.00" Storz 30 degree elbow(s) with blind cap provided aerial waterway inlet.
0746470 Waterway Shutoff Valve, Above
Swivel, Elkhart Apex, Elec Control
AERIAL WATERWAY SHUTOFF VALVE
A 5.00" electric operated butterfly valve will be installed above the swivel in the aerial inlet waterway to shut off water flow to the aerial waterway. The controller(s) will be located aerial turntable.
The valve will be controlled with an Elkhart Apex electric valve controller(s). The electric control must be of a true position feedback design, requiring no clutches in the motor or current limiting.
The controller(s) will have momentary open, close as well as programmable preset valve positions. The controller(s) will provide position indication on a full color, backlit LCD display. It will have manual adjustment of the brightness as well as an auto dimming option.
If applicable, there will be a preset relief valve in the waterway between the butterfly valve and the monitor to protect the waterway when retracting.
0047897 Tools, Aerial
TOOLS
The following tools will be provided for retorquing of all specified bolts as recommended by the manufacturer:
Torque Wrench
All Required Extensions, Sockets and Adapters
4-to-1 Multiplier
0559494 Manuals and Training, 3 Consecutive
Days, Ascendant Ladder, PAL
MANUALS
Two (2) operator maintenance manuals and two (2) wiring diagrams pertaining to the aerial device will be provided with the apparatus at time of pick-up.
INITIAL INSTRUCTION
On initial delivery of the fire apparatus, the contractor will supply a qualified representative to demonstrate the apparatus and provide initial instruction to the fire department regarding the operation, care, and maintenance of the apparatus for a period of three (3) consecutive days.
Bid #: 942 67
0807577 Cab, Tiller, Sliding Doors
TILLER CAB
A permanently mounted tiller cab will be located on top of the tiller trailer, to the rear of the aerial ladder. The maximum overall height of the tiller cab will not exceed 134.00". The tiller cab will be totally enclosed.
The cab windshield will be automotive approved tinted safety glass and will provide a minimum of 1,513 square inches of clear viewing area.
Each side window, directly rearward of the windshield, will be more than 536 square inches. The side windows, combined with the windshield, will provide a minimum of 2,585 square inches of unobstructed viewing area. In order to provide maximum visibility for the tillerman, there will be no corner posts at the forward corners of the windshield.
Two (2) slide back doors, one each side of cab will be provided. Doors will be mounted on top and bottom slides which will be lockable in either open or closed position. A minimum door opening of 21.50" will be provided when entering and exiting the tiller cab. The tiller cab doors will be equipped with drop-down windows. The windows will be 18.00" wide x 31.00" high.
The rear wall of the tiller cab will have a vertically-split sliding window. The window will be 33.50" wide x 27.75" high.
The tiller cab floor will be constructed of aluminum treadplate.
A two (2) speed electric windshield wiper with washer will be provided for the front windshield.
The windshield washer reservoir will have a capacity of two (2) quarts and will be located forward of the tiller cab.
An adjustable, telescopic steering column will be provided.
The diagnostic plug for the trailer ABS system will be provided in the driver side tiller access stepwell, behind the fuel fill door.
The following controls/alarms will be provided inside the tiller cab:
Buzzer signaling system with push button in tiller cab steering wheel as well as a labeled push button in the tractor cab, within reach of the driver.
Jackknife alarm
The following will be provided on the steering column support pedestal:
Two (2) heater/defroster outlets
Heater/defroster control switch
The following controls/gauges will be located in the upper control panel:
Tiller wheel position indicator gauge. (L-C-R)
Two (2) 2.00" diameter amber turn signal
Windshield wiper/washer control switch
0726222 Sun Visor, Smoked Lexan, Tiller Cab
A smoked Lexan™ sun visor will be provided in the tiller cab above the windshield. There will be no retention bracket provided to help secure the sun visor in the stowed position. 0636263 Light, Dome, FRP Dual LED 1lt
TILLER CAB DOME LIGHT
There will be one (1) dual LED dome light with black bezel installed in the tiller cab.
The color of the LED will be red and white.
The white LED will be controlled by the door switches and the lens switch.
The color LED will be controlled by the lens switch.
In order to ensure exceptional illumination, the white LED dome light will provide a minimum of
10.1 foot-candles (fc) covering an entire 20.00" x 20.00" square seating position when mounted
40.00" above the seat.
0725375 Heater/Defroster, Tiller Cab, Tiller,
Electric, Dual 12V, 3 Spd, Med
Climate
TILLER CAB HEATER/DEFROSTER
There will be two (2) DC Thermal, Model SA12-4000, combination heater/defroster provided in the tiller cab. The system will be 12 volt and will be powered through the tractor ignition circuit.
Each heater will have a max of 5,000BTU.
Each heater/defroster will have a 3-speed motor, a high/low heat switch, and thermostatic control located in the tiller cab within reach of the tillerman.
There will be a minimum of two (2) defrost outlets in the cab for maximum defrost performance.
The system will be 12 volt and will be powered through the tractor ignition circuit.
The heater/defrost system will have an airflow of 220 cfm. 0738925 SP Air Conditioner, Tiller Cab, Painted
Sides, 4-Way Top, Safe-Stride, 2019
TILLER CAB AIR CONDITIONING
Air conditioning will be provided for the tiller cab.
The unit will be manufactured by Danhard Inc.
The air conditioner will have cooling capacity of 13,500 BTU.
The in tiller cab venting will route via louvers included on the B-pillar of the tiller cab.
The unit will be 120 volt AC and will be run off of the onboard generator. The full load amperage draw will be 12.00 amps in the cooling mode.
The evaporator will be located ahead of the tiller cab on the top deck of the tiller trailer. The air conditioning unit will not increase the overall height of the tiller cab.
The evaporator sides will be painted to match the job color. The cover will be made of aluminum treadplate coated with black Safe-Stride® non-slip surface treatment.
Bid #: 942 68
0695671 Seat, Tiller, Pierce PS6, Premium, Air
Ride Hi-Back
TILLER CAB SEAT
A seat will be provided in the tiller cab. The seat will be a cam action type, with air suspension.
For increased convenience, the seat will include a manual control to adjust the horizontal position (6.00" travel). The manual horizontal control will be a towel-bar style located below the forward part of the seat cushion. The seat will have a reclining back adjustable from 20 degrees back to 0 degrees forward. The seat back will be a high back style with manual lumbar adjustment lever, and will include minimum 7.50" deep side bolster pads for maximum support. For optimal comfort, the seat will be provided with 17.00" deep dual density foam cushions designed with EVC (elastomeric vibration control). To ensure safe operation, the seat will be equipped with seat belt sensors in the seat cushion and belt receptacle that will activate an alarm indicating a seat is occupied but not buckled.
The seat will be furnished with a 3-point, shoulder type seat belt. The seat belt will be furnished with dual automatic retractors that will provide ease of operation in the normal seating position. 0554699 Steps,Tiller Cab Access, Moved
Rearward, Each Side
TILLER CAB STEPS
For access to the tiller cab, two (2) sets of steps will be furnished at the rear of the apparatus, one set each side. The steps will be moved rearward and be in alignment with the tiller cab door. The bottom three (3) access steps will be full width, approximately 21.00" wide, and located just behind the tiller axle. The top step will be full width, approximately 18.50" wide. The steps will be securely reinforced and constructed of aluminum treadplate. Handrails will be provided on each side of the step assemblies for maximum safety. The steps will be illuminated for nighttime operation.
0036977 Tiller Warning Indicators w/Seatbelt
Warn in Cab
JACKKNIFE ALARM
An audible and visual warning system will be provided to warn both drivers when the jackknife position approaches the maximum allowable angle.
TILLER WARNING INDICATOR
A warning indicator in the tractor cab will be activated if the parking brake is released and the tiller driver is not present in the tiller cab.
0012207 Mirror, 6" Round Convex, Tiller Cab
(PR)
CONVEX MIRRORS (tiller cab)
A 6.00" diameter round convex mirror with adjustable arm will be installed on each side of tiller cab.
0542448 Tiller 8" Convex Mirrors, Side of
Catwalk, Each Side
MOUNTING, TILLER CONVEX MIRRORS
A convex mirror will be provided on each side of the catwalk. The brackets will be approximately
10.00" tall and angle outward so the tillerman can see the rear bumper in the mirrors. The brackets will include an 8.00" convex mirror.
0051052 Window Defrost Fans (2) WINDOW DEFROST FANS
Two (2) window defrost fans will be mounted one each side. 0626771 Trailer, 3.00" Extended Gooseneck,
Single Axle Only, Tiller
TILLER TRAILER
The gooseneck area of the tiller trailer will be constructed of 100,000 psi minimum yield strength steel.
The gooseneck area will have a section modulus of 289.00 cu. in. and a resistance to bending moment of 28,900,000 inch pounds.
The gooseneck area will be 46.00" wide x 13.50" deep.
The tiller trailer frame will be box type construction to effectively resist trailer twist.
The side rails will have a 13.38" tall web over the front and mid sections of the trailer, with a continuous smooth taper to a 10.75" over the tiller axle.
The frame rails will be constructed of 80,000 psi minimum yield strength heat treated .38" thick steel, with 3.50" wide flanges and covered by top and bottom plates to form a ridged box structure. Cover plates will be 50,000 psi minimum yield strength steel.
The tiller trailer frame will have a section modulus of 257.70 cu. in., and a resisting bending moment (rbm) of 12,880,000 inch pounds over the critical regions of the frame assembly, with a section modulus of 18.96 cu. in. with an rbm of 2,085,803 inch pounds over the rear axle.
The overall length of the tiller trailer will be 471.00". The gooseneck area of the trailer will be extended 3.00".
0090681 Walkway, Turntable to Body, Tiller
WALKWAY, TURNTABLE TO BODY
A walkway will be provided from the aerial turntable to the tiller body.
Bid #: 942 69
0052481 Axle, Tiller Trailer, Oshkosh TAK-4,
Non Drive, 22,800#
TILLER TRAILER NON DRIVE AXLE
The tiller trailer axle will be of the independent suspension design with a ground rating of 22,800 lb.
Upper and lower control arms will be used on each side of the axle. Upper control arm castings will be made of 100,000-psi yield strength 8630 steel and the lower control arm casting will be made of 55,000-psi yield ductile iron.
The center cross members and side plates will be constructed out of 80,000-psi yield strength steel.
Each control arm will be mounted to the center section using elastomer bushings. These rubber bushings will rotate on low friction plain bearings and be lubricated for life. Each bushing will also have a flange end to absorb longitudinal impact loads, reducing noise and vibrations.
The upper control arm will be shorter than the lower arm so that wheel end geometry provides positive camber when deflected below rated load and negative chamber above rated load.
Camber at load will be zero degrees for optimum tire life.
The kingpin bearing will be of low friction design and be sealed for life.
Toe links that are adjustable for alignment of the wheel to the center of the trailer will be provided.
The wheel ends must have little to no bump steer when the chassis encounters a hole or obstacle.
The steering linkage will provide proper steering angles for the inside and outside wheel, based on the vehicle wheelbase.
The turning angle will be up to 24 degrees.
TILLER TRAILER NON DRIVE AXLE WARRANTY
The non drive axle system will have a three (3) year parts and labor warranty. 0032125 Steering, Sheppard M110 w/tilt, TAK4, Tiller Trailer TILLER TRAILER STEERING Dual Sheppard M110 steering gears, with integral heavy-duty power steering, will be provided.
The steering wheel will be 18.00" in diameter, and capable of tilting and telescoping.
A lock-out pin will be provided on the tiller cab steering column. 0816641 Brakes, Knorr/Bendix 17", Disc, TAK4, Tiller, Non-NFPA 1900, 2024BRAKES The tiller trailer brakes will be Knorr/Bendix disc type with a 17.00" ventilated rotor for improved stopping distance.
NFPA 1900, 2024 Edition, Section 9.3.2.5 states that clearance for tire chains will be provided in accordance with SAE J683, Tire Chain Clearance - Trucks, Buses, and Combinations of Vehicles.
This brake system does not allow adequate clearance for tire chains, therefore, the apparatus will be non-NFPA compliant at time of delivery.
0052483 Suspension, Tiller, 22,800#
SUSPENSION
Independent suspension will be provided with a minimum ground rating of 22,800 lb.
The independent suspension system will be designed to provide maximum ride comfort. The design will allow the vehicle to travel at highway speeds over improved road surfaces, and at moderate speeds over rough terrain with minimal transfer of road shock and vibration to the vehicle's crew compartment.
Each wheel will have torsion bar type spring. In addition, each wheel end will also have energy absorbing jounce bumpers to prevent bottoming of the suspension.
The suspension design will be such that there is at least 10.00" of total wheel travel and a minimum of 3.75" before suspension bottoms.
The torsion bar type spring and anchor lock system will allow for simple lean adjustments without the use of shims. Adjustment for a lean will be accomplished within 15 minutes. Anchor adjustment design is such that it allows 4.00" of ride height adjustment per side.
The independent suspension will have been put through a durability test that simulated a minimum of 140,000 miles of inner city driving.
0898937 Tires, Goodyear, Armor MAX MSA,
425/65R22.5 20 Ply (tiller)
TIRES
Tiller trailer tires will be Goodyear 425/65R22.50 radials, 20 ply Armor MAX MSA, rated for 22,800 lb maximum axle load and 68 mph maximum speed.
0037030 Wheels, Alum. Alcoa, 22.50" x 12.25"
(385/425), Tiller
WHEELS, TILLER
The tires will be mounted on Alcoa® 22.50" x 12.25" polished aluminum disc type wheels with a ten (10)-stud 11.25" bolt circle.
0037050 Oil Seals, Tiller Axle
OIL SEALS
Oil seals with viewing window will be provided on the tiller axle. 0007150 Bag of Nuts and Bolts
LOOSE EQUIPMENT
The following equipment will be furnished with the completed unit:
One (1) bag of chrome, stainless steel, or cadmium plated screws, nuts, bolts and washers, as used in the construction of the unit.
Bid #: 942 70
0816498 NFPA Required Loose Equipment,
Aerial, NFPA 2024, Provided by Fire
Department
NFPA LOOSE EQUIPMENT
NFPA Required Loose Equipment Provided by Fire Department The following loose equipment as outlined in NFPA 1900, 2024 edition, table 8.1 will be provided by the fire department:
One (1) traffic vest for each seating position, each vest to comply with ANSI/ISEA 107, American National Standard for High-Visibility Safety Apparel and Accessories, and have a five-point breakaway feature that includes two (2) at the shoulders, two (2) at the sides, and one (1) at the front.
Five (5) fluorescent orange traffic cones not less than 28.00" (711 mm) in height, each equipped with a 6.00" (152 mm) retro-reflective white band no more than 4.00" (152 mm) from the top of the cone, and an additional 4.00" (102 mm) retro-reflective white band 2.00" (51 mm) below the
6.00" (152 mm) band.
Five (5) illuminated warning devices such as highway flares, unless the five (5) fluorescent orange traffic cones have illuminating capabilities.
Four (4) ladder belts meeting the requirements of NFPA 2500.
NFPA Loose Equipment That Shall be Considered:
The following loose equipment as outlined in NFPA 1900, 2024 edition, appendix table A.8.4 (a) should be considered:
Two (2) 3 ft - 4 ft plaster hooks with D handles mounted in brackets fastened to the apparatus.
Two (2) crowbars.
Two (2) claw tools.
Two (2) 12 lb (5 kg) sledgehammers.
Four (4) SCBA apparatus
Four (4) SCBA spare cylinders
One (1) first aid kit.
Six (6) salvage covers, each a minimum size of 12 ft × 18 ft (3.6 m × 5.5 m).
Four (4) combination spanner wrenches.
Two (2) scoop shovels.
One (1) pair of bolt cutters, 24.00" (0.6 m) minimum.
One (1) 150 ft (45 m) light-use life safety rope meeting the requirements of NFPA 2500.
One (1) 150 ft (45 m) general-use life safety rope meeting the requirements of NFPA 2500.
One (1) 150 ft (45 m) utility ropes having a breaking strength of at least 5000 lb (2300 kg).
One (1) box of tools to include the following:
one (1) hacksaw with three (3) blades
one (1) keyhole saw
one (1) 12" (.3 m) pipe wrench
one (1) 24" (.6 m) pipe wrench
one (1) ballpeen hammer
one (1) pair of tin snips
one (1) pair of pliers
one (1) pair of lineman's pliers
assorted types and sizes of screwdrivers
assorted adjustable wrenches
assorted combination wrenches
One (1) automatic external defibrillator (AED).
0816939 Extinguisher, Dry Chemical, NFPA
2024, Provided by Fire Department
DRY CHEMICAL EXTINGUISHER PROVIDED BY FIRE DEPARTMENT
The extinguisher is not on the apparatus as manufactured. The fire department will provide and mount the extinguisher.
0816937 Extinguisher, 2.5 Gal. Pressurized
Water, NFPA 2024, Provided by Fire
Department
WATER EXTINGUISHER PROVIDED BY FIRE DEPARTMENT
The extinguisher is not on the apparatus as manufactured. The fire department will provide and mount the extinguisher.
0007482 Not Required, Crowbars
0007484 Not Required, Claw Tools
0816998 Axe, Flathead, Provided by Fire
Department
FLATHEAD AXE PROVIDED BY FIRE DEPARTMENT
The axe is not on the apparatus as manufactured. The fire department will provide and mount the axe.
0817000 Axe, Pickhead, Provided by Fire
Department
PICKHEAD AXE PROVIDED BY FIRE DEPARTMENT
The axe is not on the apparatus as manufactured. The fire department will provide and mount the axe.
0007494 Not Required, Sledgehammers
Bid #: 942 71
0741569 Paint Process / Environmental
Requirements, Appleton
PAINT PROCESS
The exterior custom cab and body painting procedure will consist of a seven (7) step finishing process as follows:
Manual Surface Preparation - All exposed metal surfaces on the custom cab and body will be thoroughly cleaned and prepared for painting. Imperfections on the exterior surfaces will be removed and sanded to a smooth finish. Exterior seams will be sealed before painting. Exterior surfaces that will not be painted include; chrome plating, polished stainless steel, anodized aluminum and bright aluminum treadplate.
Chemical Cleaning and Pretreatment - All surfaces will be chemically cleaned to remove dirt, oil, grease, and metal oxides to ensure the subsequent coatings bond well. The aluminum surfaces will be properly cleaned and treated using a high pressure, high temperature 4 step Acid Etch process. The steel and stainless surfaces will be properly cleaned and treated using a high temperature 3 step process specifically designed for steel or stainless. The chemical treatment converts the metal surface to a passive condition to help prevent corrosion.
Surfacer Primer - The Surfacer Primer will be applied to a chemically treated metal surface to provide a strong corrosion protective basecoat. A minimum thickness of 2 mils of Surfacer Primer is applied to surfaces that require a Critical aesthetic finish. The Surfacer Primer is a twocomponent high solids urethane that has excellent sanding properties and an extra smooth finish when sanded.
Finish Sanding - The Surfacer Primer will be sanded with a fine grit abrasive to achieve an ultrasmooth finish. This sanding process is critical to produce the smooth mirror like finish in the topcoat.
Sealer Primer - The Sealer Primer is applied prior to the Basecoat in all areas that have not been previously primed with the Surfacer Primer. The Sealer Primer is a two-component high solids urethane that goes on smooth and provides excellent gloss hold out when topcoated.
Basecoat Paint - Two coats of a high performance, two component high solids polyurethane basecoat will be applied. The Basecoat will be applied to a thickness that will achieve the proper color match. The Basecoat will be used in conjunction with a urethane clear coat to provide protection from the environment.
Clear Coat - Two (2) coats of Clear Coat will be applied over the Basecoat color. The Clear Coat is a two-component high solids urethane that provides superior gloss and durability to the exterior surfaces. Lap style and roll-up doors will be Clear Coated to match the body. Paint warranty for the roll-up doors will be provided by the roll-up door manufacturer.
After the cab and body are painted, the color will be verified to make sure that it matches the color standard. Electronic color measuring equipment will be used to compare the color sample to the color standard entered into the computer. Color specifications will be used to determine the color match. A Delta E reading will be used to determine a good color match within each family color.
All removable items such as brackets, compartment doors, door hinges, and trim will be removed and painted separately if required, to ensure paint behind all mounted items. Body assemblies that cannot be finish painted after assembly will be finish painted before assembly.
The paint finish quality levels for critical areas of the apparatus (cab front and sides, body sides and doors, and boom lettering panels) are to meet or exceed Cadillac/General Motors GMW15777 global paint requirements. Orange peel levels are to meet or exceed the #6 A.C.T. standard in critical areas. The manufacture's written paint standards will be available upon request.
Environmental Impact
Contractor will meet or exceed all current state regulations concerning paint operations. Pollution control will include measures to protect the atmosphere, water and soil. Controls will include the following conditions:
Topcoats and primers will be chrome and lead free.
Metal treatment chemicals will be chrome free. The wastewater generated in the metal treatment process will be treated on-site to remove any other heavy metals.
Particulate emission collection from sanding operations will have a 99.99 percent efficiency factor.
Particulate emissions from painting operations will be collected by a dry filter or water wash process. If the dry filter is used, it will have an efficiency rating of 98 percent. Water wash systems will be 99.97 percent efficient
Water from water wash booths will be reused. Solids will be removed on a continual basis to keep the water clean.
Paint wastes are disposed of in an environmentally safe manner.
Empty metal paint containers will be recycled to recover the metal.
Solvents used in clean-up operations will be recycled on-site or sent off-site for distillation and returned for reuse.
Additionally, the finished apparatus will not be manufactured with or contain products that have ozone depleting substances. Contractor will, upon demand, present evidence that the manufacturing facility meets the above conditions and that it is in compliance with his state EPA rules and regulations.
0709567 Paint, Single Color, Enforcer
CAB PAINT
The cab will be painted #90 red.
0709845 Paint, Single Color, Body
BODY PAINT
The body will be painted to match the single cab paint color. 0509328 Paint, Single Color, Tiller Cab
PAINT
The tiller cab will be painted #90 Red.
Bid #: 942 72
0646901 Paint Chassis Frame Assy, With
Liner, E-Coat, Standard
PAINT CHASSIS FRAME ASSEMBLY
The chassis frame assembly will be finished with a single system black top coat before the installation of the cab and body, and before installation of the engine and transmission assembly, air brake lines, electrical wire harnesses, etc.
Components that are included with the chassis frame assembly that will be painted are:
Frame rails
Frame liners
Cross members
Axles
Suspensions
Steering gear
Battery boxes
Bumper extension weldment
Frame extensions
Body mounting angles
Rear Body support substructure (front and rear)
Pump house substructure
Steel fuel tank
Castings
Individual piece parts used in chassis and body assembly Components treated with epoxy E-coat protection prior to paint:
Two (2) C-channel frame rails
Two (2) frame liners
The E-coat process will meet the technical properties shown. 0693797 No Paint Required, Aluminum Front
Wheels
0693792 No Paint Required, Aluminum Rear
Wheels
0809564 No Paint Required, Aluminum Tiller
Wheels
0733739 Paint, Axle Hubs
AXLE HUB PAINT
All axle hubs will be painted to match primary job color. 0581434 Transit Coating, Carwell, Corrosion
Protection, Including Underside
TRANSIT COATING
All non-painted metal surfaces on the exterior of the vehicle will be sprayed with a corrosion protective coating provided by Carwell. The coating can be removed with soap and water.
The coating is made of a linseed oil base and is biodegradable.
The underside non-painted metal surfaces will also be coated with a corrosion protective coating. 0756955 Compartment Paint, 909017,
Nightspots, Tiller
COMPARTMENT INTERIOR PAINT
Interior of compartments will be painted 909017, Nightspots.
Bid #: 942 73
0790913 Aerial Ladder Paint, Incl Gooseneck,
Stabilizers, Tiller
AERIAL DEVICE PAINT COLOR
The aerial device paint procedure will consist of a seven (7) step finishing process as follows:
1. Manual Surface Preparation - All exposed metal surfaces on the aerial device structural components above the rotation point will be thoroughly cleaned and mechanically shot-blasted to remove metal impurities and prepare the aerial for painting.
2. Zinc Rich Primer - Zinc rich primer will be applied to the trailer including the gooseneck and stabilizer housings, stabilizer beams and jacks, and upper 5th wheel components.
3. Primer/Surfacer Coats - A two (2) component epoxy primer/surfacer will be applied to the mechanically shot-blasted metal surfaces to provide a strong corrosion protective base coat and to smooth out the surface. All seams will be caulked with a two (2) component epoxy caulk before painting.
4. Hand Sanding - The primer/surfacer coat of the outer surfaces of the hand rails and base rails will be lightly sanded to a smooth finish.
5. Primer Coat - A two (2) component epoxy primer coat will be applied over the sanded primer.
6. Topcoat Paint - Urethane base coat will be applied to opacity for correct color matching.
7. Clear Coat - Two (2) coats of an automotive grade two (2) component urethane will be applied.
Surfaces that will not be painted include all chrome plated, polished stainless steel, anodized aluminum and bright aluminum treadplate.
All buy out components, such as monitor, nozzle, gauges, etc. will be supplied as received from the vendor.
Removable items such as brackets will be removed and painted separately to ensure paint coverage behind all mounted items.
The aerial device components will be painted as follows using the aforementioned seven (7) step finishing process:
Aerial device ladder sections and extension cylinders: white 10 Aerial turntable: white 10
Aerial control console: white 10
Aerial lift cylinders: white 10
Aerial rotation motor (if applicable): black
Aerial trailer including the gooseneck and stabilizer housings, 5th wheel components below the rotation point, body support structure, tiller axle and suspension: red 90 Aerial stabilizers: black 101
Aerial egress: #50 red (will be contrasting color to the aerial device ladder sections) Aerial boom support: gloss black primer
0544111 Reflective Band, 10"
REFLECTIVE BAND
A 10.00" white reflective band will be provided across the front of the vehicle and along the sides of the body.
0007356 Reflective across Cab Face
The reflective band provided on the cab face will be at the headlight level. 0583446 Stripe, Chevron, Rear, Diamond
Grade, Tiller
REAR CHEVRON STRIPING
There will be alternating chevron striping located on the rear-facing vertical surface of the apparatus including the rear door. The tillerman cab and rear bumper will not be covered.
The colors will be red and fluorescent yellow green diamond grade.
Each stripe will be 6.00" in width.
This will meet the requirements of the current edition of NFPA 1901, which states that 50% of the rear surface will be covered with chevron striping.
0598754 Stripe, Reflective/Diamond Grade,
4.00" on Stabilizers
REFLECTIVE STRIPE ON STABILIZERS
There will be a 4.00" wide fluorescent yellow diamond grade reflective stripe provided on the forward and rear facing side of all aerial stabilizers. 0065738 Stripe, Reflective, Cab Doors Interior,
Qtm
REFLECTIVE STRIPE, CAB DOORS
A 4.00" x 24.00" black reflective stripe will be provided across the interior of each cab door. The stripe will be located approximately 1.00" up from the bottom, on the stainless steel door panel.
This stripe will meet the NFPA 1901 requirement.
0543998 Stripe, Reflective, Tillerman Doors
Interior
REFLECTIVE STRIPE, TILLERMAN DOORS
A 6.00" x 16.00" black reflective stripe will be provided across the interior of each tillerman's entry door. The stripe will be located approximately 1.00" up from the bottom, on the door panel.
This stripe will meet the NFPA 1901 requirement.
0679788 Stripe, Vinyl, Cab Sides, IPO Chrome
Molding
CAB STRIPE
There will be a vinyl stripe provided on both sides of the cab in place of the chrome molding. 0030076 Lettering Specifications, Vinyl/Painted
0027252 Lettering, Vinyl 3" w/outline & shade
(21-40)
LETTERING
Twenty-one (21) to forty (40) non-reflective vinyl lettering, 3.00" high, outlining and shading will be provided.
Bid #: 942 74
0683997 Lettering, Vinyl, 18.00", Each
LETTERING
There will be non-reflective vinyl lettering, 18.00" high, with no outline or shade provided. There will be three (3) letters provided.
0684006 Lettering, Vinyl, 11.00", (21-40)
LETTERING
Twenty-one (21) to forty (40) non-reflective vinyl lettering, 11.00" high, with outline and shade will be provided.
0684036 Lettering, Vinyl, 5.00", Each
LETTERING
There will be non-reflective vinyl lettering, 5.00" high, with outline and shade provided. There will be four (4) letters provided.
0685993 Lettering, Reflective, 10.00", Each
LETTERING
There will be reflective lettering, 10.00" high, with no outline or shade provided. There will be two (2) letters provided.
0686002 Lettering, Reflective, 8.00", Each
LETTERING
There will be reflective lettering, 8.00" high, with outline and shade provided. There will be seven (7) letters provided.
0686007 Lettering, Reflective, 7.00", Each
LETTERING
There will be reflective lettering, 7.00" high, with outline and shade provided. There will be one (1) letter provided.
0686013 Lettering, Reflective, 6.00", Each
LETTERING
There will be reflective lettering, 6.00" high, with outline and shade provided. There will be one (1) letter provided.
0686033 Lettering, Reflective, 4.00", Each
LETTERING
There will be reflective lettering, 4.00" high, with outline and shade provided. There will be 12 letters provided.
0686080 Lettering, Reflective, 3.00", (41-60)
LETTERING
Forty-one (41) to sixty (60) reflective lettering, 3.00" high, with no outline or shade will be provided.
0623673 SP Lettering, RTape Vinyl EFX Smooth
Gold, Salinas, CA(Not covered under
warranty)
VINYL LETTERING
There will be RTape vinyl EFX smooth gold #3102 lettering with gradient effect. That will be located Cab. This is not covered under Pierce warranty. 0655896 Sign Kit, Painted, Holder and Insert,
Each
SIGN KIT FOR LETTERING/NUMERALS
four (4) painted stainless steel plate(s) and holder(s) will be provided for department lettering.
They will be mounted 0ne (1) Front Bumper, One (1) RS Crew Cab, One (1) LS Crew Cab, One RS Rear and 12"W x 10" H in size.
0000387 Emblem, Eagle Hose 2, Color
Imaged, Pair
EAGLE HOSE #2 EMBLEMS
A pair of emblems, 13.00" or less in Diameter, featuring a "Flying American Flag" and an "Eagle Holding a Fire Hose", all within a gold circle, will be installed Located on tiller cab door.. The design will be color imaged.
0684221 Emblem, Maltese Cross, Printed
Effect Gold Leaf, 12"-14", Pair
MALTESE CROSS INSTALLATION
There will be one (1) pair of maltese crosses, comprised of printed effect gold leaf material, provided and installed between the front doors and the side window up high.
Bid #: 942 75
0772003 Manual, Fire Apparatus Parts, USB
Flash Drive, Custom
FIRE APPARATUS PARTS MANUAL
There will be one (1) custom parts manual(s) in USB flash drive format for the complete fire apparatus provided.
The manual(s) will contain the following:
Job number
Part numbers with full descriptions
Table of contents
Parts section sorted in functional groups reflecting a major system, component, or assembly Parts section sorted in alphabetical order
Instructions on how to locate parts
Each manual will be specifically written for the chassis and body model being purchased. It will not be a generic manual for a multitude of different chassis and bodies.
Service Parts Internet Site
The service parts information included in these manuals are also available on the Pierce website.
The website offers additional functions and features not contained in this manual, such as digital photographs and line drawings of select items. The website also features electronic search tools to assist in locating parts quickly.
0772037 Manual, Chassis Service, USB Flash
Drive, Custom
CHASSIS SERVICE MANUALS
There will be one (1) chassis service manuals on USB flash drives containing parts and service information on major components provided with the completed unit.
The manual will contain the following sections:
Job number
Table of contents
Troubleshooting
Front Axle/Suspension
Brakes
Engine
Tires
Wheels
Cab
Electrical, DC
Air Systems
Plumbing
Appendix
The manual will be specifically written for the chassis model being purchased. It will not be a generic manual for a multitude of different chassis and bodies. 0773381 Manual, Chassis Operation, (1) USB
Flash Drive, Custom
CHASSIS OPERATION MANUAL
The chassis operation manual will be provided on one (1) USB flash drive. 0030008 Warranty, Basic, 1 Year, Apparatus,
WA0008
ONE (1) YEAR MATERIAL AND WORKMANSHIP
A Pierce basic apparatus limited warranty certificate, WA0008, is included with this proposal. 0696698 Warranty, Engine, Cummins, 5 Year,
WA0181
ENGINE WARRANTY
A Cummins five (5) year limited engine warranty will be provided. A limited warranty certificate, WA0181, is included with this proposal.
0684953 Warranty, Steering Gear, Sheppard
M110, 3 Year WA0201
STEERING GEAR WARRANTY
A Sheppard three (3) year limited steering gear warranty will be provided. A copy of the warranty certificate will be submitted with this proposal.
0596017 Warranty, Frame, 50 Year, Custom
Chassis, WA0013
FIFTY (50) YEAR STRUCTURAL INTEGRITY
The Pierce custom chassis frame limited warranty certificate, WA0013, is included with this proposal.
0595698 Warranty, Axle, 3 Year, TAK-4,
WA0050
FRONT AXLE THREE (3) YEAR MATERIAL AND WORKMANSHIP WARRANTY The Pierce TAK-4 suspension limited warranty certificate, WA0050, is included with this proposal. 0733306 Warranty, Single Axle, 5 Year, Meritor,
General Service, WA0384
SINGLE REAR AXLE FIVE (5) YEAR MATERIAL AND WORKMANSHIP WARRANTY A Meritor™ Axle 5 year limited warranty will be provided. 0652758 Warranty, ABS Brake System, 3 Year,
Meritor Wabco, WA0232
ABS BRAKE SYSTEM THREE (3) YEAR MATERIAL AND WORKMANSHIP WARRANTY A Meritor Wabco™ ABS brake system limited warranty certificate, WA0232, is included with this proposal.
0019914 Warranty, Structure, 10 Year, Custom
Cab, WA0012
TEN (10) YEAR STRUCTURAL INTEGRITY
The Pierce custom cab limited warranty certificate, WA0012, is included with this proposal.
Bid #: 942 76
0744240 Warranty, Paint, 10 Year, Cab, ProRate, WA0055 TEN (10) YEAR PRO-RATED PAINT AND CORROSION
A Pierce cab limited pro-rated paint warranty certificate, WA0055, is included with this proposal. 0524627 Warranty, Electronics, 5 Year, MUX,
WA0014
FIVE (5) YEAR MATERIAL AND WORKMANSHIP
The Pierce Command Zone electronics limited warranty certificate, WA0014, is included with this proposal.
0695416 Warranty, Pierce Camera System,
WA0188
CAMERA SYSTEM WARRANTY
A Pierce fifty four (54) monthwarranty will be provided for the camera system. 0647720 Warranty, Pierce LED Strip Lights,
WA0203
COMPARTMENT LIGHT WARRANTY
The Pierce 12 volt DC LED strip lights limited warranty certificate, WA0203, is included with this proposal.
0046369 Warranty, 5-year EVS Transmission,
Standard Custom, WA0187
TRANSMISSION WARRANTY
The transmission will have a five (5) year/unlimited mileage warranty covering 100 percent parts and labor. The warranty will be provided by Allison Transmission.
Note: The transmission cooler is not covered under any extended warranty you may be getting on your Allison Transmission. Please review your Allison Transmission warranty for coverage limitations.
0685945 Warranty, Transmission Cooler,
WA0216
TRANSMISSION COOLER WARRANTY
The transmission cooler will carry a five (5) year parts and labor warranty (exclusive to the transmission cooler). In addition, a collateral damage warranty will also be in effect for the first three (3) years of the warranty coverage and will not exceed $10,000 per occurrence. A copy of the warranty certificate will be included with this proposal. 0596025 Warranty, Structure, 10 Year, Body,
WA0009
TEN (10) YEAR STRUCTURAL INTEGRITY
The Pierce apparatus body limited warranty certificate, WA0009, is included with this proposal. 0693126 Warranty, AMDOR, Roll-up Door, 10
Year/5 Year Painted, WA0185
ROLL UP DOOR MATERIAL AND WORKMANSHIP WARRANTY
An AMDOR roll-up door limited warranty will be provided. The roll-up door will be warranted against manufacturing defects for a period of ten (10) years. A five (5) year limited warranty will be provided on painted roll up doors.
The limited warranty certificate, WA0185, is included with this proposal. 0006999 Warranty, Structure, 20 Year, Aerial
Device, WA0052
TWENTY (20) YEAR AERIAL DEVICE STRUCTURAL INTEGRITY WARRANTY The Pierce device limited warranty certificate, WA0052, is included with this proposal. 0687388 Warranty, Swivels, 5 Year, Aerial
Device, WA0197
AERIAL SWIVEL WARRANTY
An Amity five (5) year limited swivel warranty will be provided. A copy of the warranty certificate will be included with this proposal.
0685727 Warranty, Hydraulic System and
Components, 3 Year/5 Year, WA0200
HYDRAULIC SYSTEM COMPONENTS WARRANTY
Aerial hydraulic system components will be provided with a five (5) year material and workmanship limited warranty.
HYDRAULIC SEAL WARRANTY
Aerial hydraulic seals will be provided with a three (3) year material and workmanship limited warranty.
A copy of the warranty certificates is included with this proposal. 0687327 Warranty, Waterway, 10 Year, Aerial
Device, WA0198
AERIAL WATERWAY WARRANTY
An Amity ten (10) year limited waterway warranty will be provided. A copy of the warranty certificate is included with this proposal.
0595860 Warranty, Paint, 4 Year, Aerial
Device, Pro-Rated, WA0047
FOUR (4) YEAR PRO-RATED PAINT AND CORROSION
A Pierce aerial device limited pro-rated paint warranty certificate, WA0047, is included with this proposal.
0725636 Warranty, Harrison Generator, 2 Year
TWO (2) YEAR GENERATOR MATERIAL AND WORKMANSHIP WARRANTY A Harrison Hydra-Gen generator two (2) yearlimited warranty will be provided. 0595820 Warranty, Paint, 10 Year, Body, ProRate, WA0057 TEN (10) YEAR PRO-RATED PAINT AND CORROSION A Pierce body limited pro-rated paint warranty certificate, WA0057, is included with this proposal.
Bid #: 942 77
0595412 Warranty, Graphics Lamination, 1
Year, Apparatus, WA0168
ONE (1) YEAR MATERIAL AND WORKMANSHIP
The Pierce graphics fading and deterioration limited warranty limited warranty certificate, WA0168, is included with this proposal.
0819254 Certification, Vehicle Stability,
CD0196
VEHICLE STABILITY CERTIFICATION
The fire apparatus manufacturer will provide a certification stating the apparatus complies with NFPA 1900, current edition, section 7.14, Vehicle Stability. The certification is included with this proposal.
0808564 Certification, Engine Installation, Enf,
Cummins X15, 2027
ENGINE INSTALLATION CERTIFICATION
The fire apparatus manufacturer will provide a certification, along with a letter from the engine manufacturer stating they approve of the engine installation in the bidder's chassis. The certification will be provided at the time of delivery. 0686786 Certification, Power Steering,
CD0098
POWER STEERING CERTIFICATION
The fire apparatus manufacturer will provide a certification stating the power steering system as installed meets the requirements of the component supplier. The certification is included with this proposal.
0892691 Certification, Cab Integrity, Saber
FR/Enforcer, CD0189
CAB INTEGRITY CERTIFICATION
The fire apparatus manufacturer will provide a cab crash test certification with this proposal. The certification will state that a specimen representing the substantial structural configuration of the cab has been tested and certified by an independent third party test facility. Testing events will be documented with photographs, real-time and high-speed video, vehicle accelerometers, cart accelerometers, and a laser speed trap. The fire apparatus manufacturer will provide a state licensed professional engineer to witness and certify all testing events. Testing will meet or exceed the requirements below:
SAE J2422 Cab Roof Strength Evaluation - Quasi-Static Loading Heavy Trucks.
European Occupant Protection Standard ECE Regulation No.29.
SAE J2420 COE Frontal Strength Evaluation - Dynamic Loading Heavy Trucks.
Side Impact
The cab will be subjected to dynamic preload where a 14,320-lb moving barrier is slammed into the side of the cab at 5.50 mph, striking with an impact of 13,000 ft-lb of force. This test is part of the SAE J2422 test procedure and more closely represents the forces a cab will see in a rollover incident.
Frontal Impact
The same cab will withstand a frontal impact of 32,600 ft-lb of force using a moving barrier in accordance with SAE J2420.
Additional Frontal Impact
The same cab will withstand a frontal impact of 65,098 ft-lb of force using a moving barrier. (Twice the force required by SAE J2420)
Roof Crush
The cab will be subjected to a roof crush force of 22,500 lb. This value meets the ECE 29 criteria, and is equivalent to the front axle rating up to a maximum of ten (10) metric tons.
Additional Roof Crush
The same cab will be subjected to a roof crush force of 110,000 lbs. (Four and a half times the load criteria of ECE 29)
The same cab will withstand all tests without any measurable intrusion into the survival space of the occupant area.
There will be no exception to any portion of the cab integrity certification. Nonconformance will lead to immediate rejection of bid.
0631973 Certification, Cab Door Durability,
Saber FR/Enforcer, CD0137
CAB DOOR DURABILITY CERTIFICATION
Robust cab doors help protect occupants. Cab doors will survive a 200,000 cycle door slam test where the slamming force exceeds 20 G's of deceleration. The bidder will certify that the sample doors similar to those provided on the apparatus have been tested and have met these criteria without structural damage, latch malfunction, or significant component wear. 0631978 Certification, Windshield Wiper
Durability, Saber FR/Enforcer,
CD0132
WINDSHIELD WIPER DURABILITY CERTIFICATION
Visibility during inclement weather is essential to safe apparatus performance. Windshield wipers will survive a 3 million cycle durability test in accordance with section 6.2 of SAE J198 Windshield Wiper Systems - Trucks, Buses and Multipurpose Vehicles. The bidder will certify that the wiper system design has been tested and that the wiper system has met these criteria. 0631974 Certification, Electric Window
Durability, Saber FR/Enforcer,
CD0133
ELECTRIC WINDOW DURABILITY CERTIFICATION
Cab window roll-up systems can cause maintenance problems if not designed for long service life. The window regulator design will complete 30,000 complete up-down cycles and still function normally when finished. The bidder will certify that sample doors and windows similar to those provided on the apparatus have been tested and have met these criteria without malfunction or significant component wear.
Bid #: 942 78
0631977 Certification, Seat Belt Anchors and
Mounting, Saber FR/Enforcer,
CD0134
SEAT BELT ANCHOR STRENGTH
Seat belt attachment strength is regulated by Federal Motor Vehicle Safety Standards and should be validated through testing. Each seat belt anchor design will withstand 3000 lb of pull on both the lap and shoulder belt in accordance with FMVSS 571.210 Seat Belt Assembly Anchorages.
The bidder will certify that each anchor design was pull tested to the required force and met the appropriate criteria.
SEAT MOUNTING STRENGTH
Seat attachment strength is regulated by Federal Motor Vehicle Safety Standards and should be validated through testing. Each seat mounting design will be tested to withstand 20 G's of force in accordance with FMVSS 571.207 Seating Systems. The bidder will certify, at time of delivery, that each seat mount and cab structure design was pull tested to the required force and met the appropriate criteria.
0735949 Certification, Cab HVAC System
Performance, SFR/Enf,
CD0165/CD0167/CD0174/CD0175
PERFORMANCE CERTIFICATIONS
Cab Air Conditioning
Good cab air conditioning temperature and air flow performance keeps occupants comfortable, reduces humidity, and provides a climate for recuperation while at the scene. The cab air conditioning system will cool the cab from a heat-soaked condition at 100 degrees Fahrenheit to an average of 78 degrees Fahrenheit in 30 minutes. The bidder will certify that a substantially similar cab has been tested and has met these criteria.
Cab Defroster
Visibility during inclement weather is essential to safe apparatus performance. The defroster system will clear the required windshield zones in accordance with SAE J381 Windshield Defrosting Systems Test Procedure And Performance Requirements - Trucks, Buses, And Multipurpose Vehicles.The bidder will certify that the defrost system design has been tested in a cold chamber and passes the SAE J381 criteria.
Cab Auxiliary Heater
Good cab heat performance and regulation provides a more effective working environment for personnel, whether in-transit, or at a scene. An auxiliary cab heater will warm the cab 77 degrees Fahrenheit from a cold-soak, within 30 minutes when tested using the coolant supply methods found in SAE J381. The bidder will certify, at time of delivery, that a substantially similar cab has been tested and has met these criteria.
0545073 Amp Draw Report, NFPA Current
Edition
AMP DRAW REPORT
The bidder will provide, at the time of bid and delivery, an itemized print out of the expected amp draw of the entire vehicle's electrical system.
The manufacturer of the apparatus will provide the following:
Documentation of the electrical system performance tests.
A written load analysis, which will include the following:
The nameplate rating of the alternator.
The alternator rating under the conditions specified per:
Current edition of applicable NFPA standards.
The minimum continuous load of each component that is specified per:
Current edition of applicable NFPA standards.
Additional loads that, when added to the minimum continuous load, determine the total connected load.
Each individual intermittent load.
All of the above listed items will be provided by the bidder per the current edition of applicable NFPA standards.
0002758 Amp Draw, NFPA/ULC Radio
Allowance
0799248 Appleton/Florida BTO
0000029 TILLER BODY
0000012 PIERCE CHASSIS
0004713 ENGINE, OTHER
0046396 EVS 4000 Series TRANSMISSION
0020037 NO PUMP
0020015 ABS SYSTEM
0658751 PUMPER BASE
Bid #: 942 79
Option Description Type* Minimum
Load
Intermittent
Load
Total
Connected
0001244 High Idle w/Electronic Engine, Custom 0.00 1.20 0.00 0026408 Wiring, Customer Installed Radio, Battery-Direct, Ignition-Power & Ground
0.00 36.00 0.00
0067509 Switch, Additional for Lightbar 0.00 0.00 0.08
0079211 Batteries, (6) Stryten/Exide Grp 31, 950 CCA each, Threaded Stud 0.00 3.00 0.00 0511739 Remote Start, Hydraulic Generator, PTO and Field - SAME SWITCH
0.00 1.00 0.00
0550452 Lights, Side Scene, Zico ZQL-SS-LED, Stainless 1st 0.00 0.00 1.00 0552317 Lights, Perimeter, Wln 20C0CDCR 0.00 0.00 2.40
0583938 Lights, Engine Compt, Custom, Auto Sw, Wln 3SC0CDCR, 3" LED, Trim
0.00 0.30 0.00
0589905 Alarm, Back-up Warning, PRECO 1040 0.00 0.50 0.00 0626097 Light, Map, Sunnex HS76*-00 Series, Swivel Joint, Clear Lens, Ceiling Mount
0.00 0.00 1.56
0630020 Lights, Side, Wln M6* LED, Prk Brk Deactivation 0.00 2.70 1.80 0630636 Controls, Electric Roll-Up Windows, 4dr, 4 Driver Controls, Saber FR/Enforcer
0.00 26.00 0.00
0639726 Cab Lift, Elec/Hyd, Manual Override, Unlocked Ind Light, Saber FR/Enforcer
0.00 180.00 0.00
0661232 Compt, At Rear Between Tow Eyes, Divider, Smooth Alum Sngl Pan Dr, D Ring,Tiller
0.00 0.00 1.80
0662753 Stabilizers, 100'/105' HD Tractor Drawn Steel Aerial, Split Pan, 17' Spread
0.00 2.00 0.00
0666072 Lights, Tractor Scene, Wln M6ZC LED Rear of Cab 2lts 0.00 0.00 4.00 0683556 Light, Do Not Move Apparatus, Wln M2R Red LED 0.00 0.50 0.00 0687994 Engine Brake, Jacobs Compression Brake, Cummins Engine 0.00 0.42 0.00 0690488 Lights, Side Scene, Zico ZQL-SS-LED, Stainless 2nd 0.00 0.00 1.00 0750408 Lights, Side, Wln PS*01FCR LED 1st 0.00 2.88 1.92 0772592 Speakers, Panasonic, (2) Additional, Tiller Cab 0.00 0.00 3.00 0777954 Light, Indicator, Jackknife Warning, Wln 3S*00F*R 0.00 0.50 0.00 0804719 Handlts, (4) Streamlight, Fire Vulcan, 44451, C4 LED, Tail Lts, 12v, Orange
0.00 0.00 4.40
0804781 Aerial Scene Lts Separated into Aerial Tip Category and Aerial Tracking Category
0.00 0.00 0.00
0805325 Light, Directional, Wln M62T* LED, 15 Degree Angle Bracket, Additional
0.00 1.50 0.00
0805618 Lights, Backup, Wln M62BU 0.00 3.20 0.00
0816632 Intercom, David Clark, 8-Pos, 3-Dual Radio, (D, O, TC, RPTT), 4C, T
0.00 0.00 0.50
0817058 Camera, Pierce, LS Mux, R Camera, SD, CL714 0.00 1.20 0.00 0819994 Radio, Jensen, AM/FM/WB, Bluetooth 0.00 0.00 2.00 0820911 Wiring, Spare, 15 A 12V DC 6th NFPA1900 0.00 0.00 90.00 0822289 ABS/ATC Wabco Brake System, Single Axle, Tiller, NFPA 1900 0.00 6.00 0.00 0893726 Lights, Turntable Walkway, P25, LED, Job Color Brackets 0.00 0.00 0.00 0895281 Siren, Federal Q2B, Littelfuse 24213 Sol 0.00 100.00 0.00 0547328 Wiring, Spare, 20 A 12V DC, Switch Feature 1st Load Managed 0.00 0.00 120.00 0618906 Lighting, Rung, LED, TecNiq, 4 Section, Base, Lower/Upper Mid, Fly, 3 Colors RWB
Load Managed 0.00 0.00 20.00
0722038 HVAC, Heavy-Duty, Enforcer, w/X15, CARE Load Managed 0.00 0.00 100.00 0725375 Heater/Defroster, Tiller Cab, Tiller, Electric, Dual 12V, 3 Spd, Med Climate
Load Managed 0.00 0.00 75.00
0736743 Light, Wln, 12V PSL2** Slm Ln, 12 VDC 2nd Load Managed 0.00 0.00 12.00 0736755 Light, Wln, 12V PSL2** Slm Ln, 12 VDC 1st Load Managed 0.00 0.00 12.00 0768928 Lights, Wln, PSL2** Pioneer, 12 VDC, 2nd Load Managed 0.00 0.00 12.20 0768929 Lights, Wln, PSL2** Pioneer, 12 VDC, 1st Load Managed 0.00 0.00 12.20 0769589 Lights, Stabilizer Pad Locator, Wln Micro MPB*, Rec Stb S Pn, Cnt Ft
Load Managed 0.00 0.00 7.00
0774948 Lights, Wln, P*H1* Pioneer, 12 VDC, 2nd Load Managed 0.00 0.00 6.50 0775524 Lights, Wln, P*H1* Pioneer, 12 VDC, 1st Load Managed 0.00 0.00 6.50 0776357 Light, Visor, Wln, 12V P*H2* Pioneer, Cnt Feature, 1st Load Managed 0.00 0.00 13.00 0821191 Wiring, Spare, 20 A 12V DC, Batt Dir, 1st NFPA1900 Load Managed 0.00 0.00 20.00 0889974 Light, Wln, 12V PSL2** Slm Ln, 12 VDC 3rd Load Managed 0.00 0.00 5.46 * UDMC = User Defined Mission Critical, LM = User Defined Load Managed, S = Electrical Amperage Supply 1 Electrical Analysis 5/1/2024
Bid #: 942
100' Tiller (duplicate to 28976) Sales Rep:
Organization:
Young, Dewayne
Golden State Fire Apparatus, Inc
Desc:
Job #:
Customer: Salinas Fire Department
Option: Pierce Command Zone, Advanced Electronics & Control System, Enforcer, WiFi CZT
Type: Multiplexed
Option Description Type* Minimum
Load
Intermittent
Load
Total
Connected
0002565 Hourmeter, Aerial Inside Cab NFPA 0.10 0.00 0.00 0002615 Switch, Aerial 12V Master NFPA 0.08 0.00 0.00
0002758 Amp Draw, NFPA/ULC Radio Allowance NFPA 5.00 0.00 0.00 0010458 Platform, Slide Out, 500 lb Capacity, w/Morton Cass NFPA 3.00 0.00 0.00 0036503 Compt, F/H, Trans Front, Roll, LS Center, Tiller NFPA 1.80 0.00 1.80 0036512 Compt, F/H, Trans Front, Roll, RS Center, Tiller NFPA 1.80 0.00 1.80 0059809 Light, Marker, Weldon, 9186-1500 LED, Location NFPA 0.10 0.00 0.00 0068703 Lights, Grote Supernova LED, Stabilizer Beam, (1) Set NFPA 1.60 0.00 0.00 0088745 Light, Rear Zone Up, Wln L31HRFN LED Beacon, Red LED NFPA 3.20 4.80 0.00 0092582 Load Manager/Sequencer, MUX NFPA 0.56 0.56 0.00 0120788 Control Stations, 100'/105' Tiller NFPA 4.26 0.00 0.00 0529588 Generator, Harrison 8kW, 8.0MAS-16R/D-11011/15/1, Hydraulic, Hotshift PTO
NFPA 35.31 0.00 0.00
0534379 Flowmeter, FRC, Waterway, PAL NFPA 0.50 0.00 0.00 0534987 Lights, Clearance/Marker/ID, Rear, Truck-Lite 33050R LED 7Lts, Aerial
NFPA 0.35 0.00 0.00
0540701 Lights, Stabilizer Warn (1) Set, Wln M6* LED, Front Colored Lens NFPA 1.80 2.70 0.00 0540777 Lights, Rear Zn Lwr, Wln M6*, Colored Lens NFPA 1.80 2.70 0.00 0554516 Lights, Step, P25 LED, Tiller, Aerial Master NFPA 0.50 0.00 0.00 0568012 Air Dryer, Wabco System Saver 1200, Heater, 2010 NFPA 7.81 0.00 0.00 0601973 Lights, Stabilizer Scene, (1) set, Truck-Lite 44042C, LED NFPA 1.00 0.00 0.00 0602100 Lights, Torque Box Ladder Storage, Pierce LED Strip Lights, 2 Lts NFPA 1.00 0.00 0.00 0605488 Lightbar, Wln, Freedom IV-Q, 81", RRRRWsrR_Opt_RsrWRRRR NFPA 6.48 2.68 9.92 0605598 Lightbars, Wln, Freedom IV-Q, 2-21.5", RRRRR RRRRR NFPA 6.48 0.00 9.76 0620054 Light, Directional/Marker, Intermediate, Weldon 9186-8580-29 LED 2lts
NFPA 0.10 0.90 0.00
0622803 Cab Instruments, Black Gauges, Black Bezels, Enforcer MUX NFPA 1.26 0.00 0.00 0625210 Lights, Directional, Cab Front Side, Truck-Lite 19036Y LED, AXT/Enf
NFPA 0.12 0.00 0.00
0625650 Cab, Enforcer, 7000 NFPA 6.80 10.20 0.00
0625953 Light, Directional, Wln 600 Cmb, Cab Crn, Wrp Bzl Out HD Lts, Enf, Sab FR
NFPA 0.70 0.70 0.00
0626588 Lights, Perimeter Cab, TecNiq T10-LC00-1 15" LED 4Dr NFPA 1.60 0.00 0.00 0642936 Timer, Havis Chargeguard Select CG-X NFPA 0.04 0.00 0.00 0647647 Lights, Dome, FRP Dual LED 4 Lts NFPA 0.80 0.80 0.00 0647802 Lights, Clearance/Marker/ID, Front, P25 LED 5 Lts, Saber FR/Enforcer
NFPA 0.35 0.00 0.00
0652577 Compt, F/H, Trans Roll, Special Generator Mounting, 92.00" Wide, RS Front,Tiller
NFPA 1.80 0.00 1.80
0652578 Compt, F/H, Trans Roll, Special Generator Mounting, 92.00" Wide, LS Front,Tiller
NFPA 1.80 0.00 1.80
0653937 Flasher, Headlight Alternating NFPA 0.08 0.00 0.00 0665700 Light, Slide-Out Pump Operator Step, Not Required NFPA 0.65 0.00 0.00 0680193 Ladder Storage, Vertically Hinged Doors, Smooth Alum, Grabber Door Brkt, Tiller
NFPA 0.90 0.00 0.90
0689539 Lights, Compt, Pierce, LED Light Strip, 36", Additional NFPA 0.35 0.35 0.00 0689540 Lights, Compt, Pierce, LED Light Strip, 27", Additional NFPA 0.52 0.52 0.00 0689541 Lights, Compt, Pierce, LED Light Strip, 9", Additional NFPA 0.09 0.09 0.00 0733396 Light, Locator, Wln L31H*F, LED, at Tip, PAL/PAP, 1lt NFPA 1.60 2.40 4.00 0737181 Intercom, 2-Way Fire Research ICA910 Hands Free NFPA 0.50 0.00 0.00 0746667 Lights, Side Zone Lower, Wln M6**, M6**, 4Lts NFPA 3.60 5.40 0.00 0748168 Cabinet, Rear Facing, RS, 26.75 W x 30 H x 22 D, Ext Acc Only, SFR/Enf
NFPA 0.30 0.30 0.00
0748169 Cabinet, Rear Facing, LS, 26.75 W x 30 H x 23 D, Ext Acc Only, SFR/Enf
NFPA 0.30 0.30 0.00
0748170 Cabinet, Rear Facing, Top Eng Tnl, 38 W x 15 H x 18 D, Web, Notch, SFR/Enf
NFPA 0.15 0.15 0.00
0760732 Lights, Perimeter Body, TecNiq T10-LC00-1 15" LED 4lts, Turntbl/Rr Stp, Tiller
NFPA 1.52 0.00 0.00
0761731 Lights, Front Zone, Wln M6** M6** M6** M6**, 4lts Q Bezel, Clr Fet
NFPA 3.60 5.40 0.00
0762396 Light, Turntable Console, Amdor AY-LB-12HW012, LED Strip Light NFPA 0.20 0.00 0.00 * UDMC = User Defined Mission Critical, LM = User Defined Load Managed, S = Electrical Amperage Supply 2 Electrical Analysis 5/1/2024
Bid #: 942
100' Tiller (duplicate to 28976) Sales Rep:
Organization:
Young, Dewayne
Golden State Fire Apparatus, Inc
Desc:
Job #:
Customer: Salinas Fire Department
Option: Pierce Command Zone, Advanced Electronics & Control System, Enforcer, WiFi CZT
Type: Multiplexed
Option Description Type* Minimum
Load
Intermittent
Load
Total
Connected
0762413 Light, Boom Support, Amdor AY-LB-12HW012, 12" LED NFPA 0.18 0.00 0.00 0763582 DEF Tank, 4.5 Gallon, DS Fill, Forward of Rear Axle, Tiller NFPA 0.60 11.40 0.00 0783153 Headlights, Rect LED, JW Spkr Evo 2, AXT/DCF/Enf/Imp/Sab/Vel NFPA 4.20 4.20 0.00 0791528 Light, Traffic Directing, Wln TAL65, 36.00" Long, TACTL5 NFPA 0.60 1.20 0.00 0793424 Compt, F/H F/D Front/Rear Roll, Center Lift Past 90, Special Cab Steps,78"Wide
NFPA 3.60 0.00 3.60
0802753 Lights, Tracking, Wln MP** LED, 2lts NFPA 8.00 0.00 0.00 0804519 Lights, Tail, Wln M62BTT* Red Stop/Tail & M62T* Amber Dir Arw w/Flange
NFPA 0.83 2.49 0.00
0808497 Engine, Cummins X15, 565 hp, 1850 lb-ft, W/OBD, EPA 2027, Enforcer
NFPA 6.00 0.00 0.00
0814201 Vehicle Information Center, 7" Color Display, Touchscreen, MUX, CL714
NFPA 1.20 0.00 0.00
0816093 ClearSky Telematics, Remote Fleet & On-scene Management, AT&T Commercial
NFPA 1.61 0.00 0.00
0819013 Siren, Code 3 3692 100/200W, Other Speaker, Non-NFPA 2024 NFPA 1.40 12.60 0.00 0820601 Lights, Tip, Wln MP** LED, 4lts NFPA 16.00 0.00 0.00 0822192 Compt, F/H F/D Front Roll, Low Rear Roll, Spec Cab Steps, Narrow Rear
NFPA 1.80 0.00 1.80
0824055 Compt,Single Reserv,22.5"HTop Stg Area w/Ctr Lift,Grating,F/D Ea Side,Dbl Dr.47"
NFPA 1.80 0.00 1.80
0887546 Trans, Allison 6th Gen, 4000 EVS P, w/Prognostics, Imp/Vel/SFR/Enf
NFPA 2.00 2.00 0.00
0889577 Bracket, License Plate & Light, P25 LED, Stainless Brkt NFPA 0.07 0.00 0.00 0892638 Lights, Cab & Crw Cab Acs Stps, P25, LED w/Bezel, 6lts NFPA 1.00 0.00 0.00 0893414 Aerial, 100' Heavy Duty Ladder, Tiller (500 dry/500 water) NFPA 5.00 0.00 0.00 0647728 Alternator, 430 amp, Delco Remy 55SI S 0.00 0.00 0.00 Load Totals: 170.15 443.74 576.30
Minimum Continuous Load
Supply: 253.00
Demand: 170.15
Variance: 82.85
Total Connected Load
Supply: 369.00
Demand: 324.59
Variance: 44.41
Note: Minimum Continous Load is in "Blocking Right of Way" mode.(Reference current edition of NFPA 1901) Note: Intermittent Load items are not factored in on any alternator load comparisons. These items are included on the report for reference only and should be looked at as amp draw exclusion items. (Reference current edition of NFPA 1901) Note: Total Connected Load "Demand" represents Total Connected Load minus any Load Managed items Alternator Output at Idle: 253.00 Alternator Output at Governed Speed: 369.00 * UDMC = User Defined Mission Critical, LM = User Defined Load Managed, S = Electrical Amperage Supply 3 Electrical Analysis 5/1/2024
Bid #: 942
100' Tiller (duplicate to 28976) Sales Rep:
Organization:
Young, Dewayne
Golden State Fire Apparatus, Inc
Desc:
Job #:
Customer: Salinas Fire Department
Option: Pierce Command Zone, Advanced Electronics & Control System, Enforcer, WiFi CZT
Type: Multiplexed
Turning Performance Analysis
Bid Number: 942 Chassis: Enforcer Chassis, Tractor (Tiller) Department: Salinas Fire Department Body: Aerial, Tiller, No Pump, Alum Body Parameters:
*Inside Cramp Angle: 45°
Axle Track: 82.92 in.
Wheel Offset: 3.12 in.
Tread Width: 12.4 in.
Chassis Overhang: 65.95 in.
Additional Bumper Depth: 7 in.
Front Overhang: 72.95 in.
Wheelbase: 166 in.
Calculated Turning Radii:
Inside Turn: 13 ft. 1 in.
Curb to curb: 25 ft. 9 in.
Wall to wall: 29 ft. 4 in.
Notes:
*Actual Inside cramp angle may be less than shown.
Curb to Curb turning radius calculated for 9.00 inch curb. 05/01/2024
Category Option Description
Aerial Devices 0893414 Aerial, 100' Heavy Duty Ladder, Tiller (500 dry/500 water) Bumpers 0606186 Bumper, Non-Extended, Saber FR/Enforcer Axle, Front, Custom 0630705 Axle, Front, Oshkosh TAK-4, Non Drive, 19,500 lb, Enforcer Wheels, Front 0019575 Wheels, Front, Alcoa, 22.50" x 9.00", Aluminum, Hub Pilot Tires, Front 0582936 Tires, Front, Goodyear, G289 WHA, 315/80R22.50, 20 ply Definitions:
Inside CrampAngle Maximum turning angle of the front inside fire.
Axle Track King-pin to King-pin distance of front axle.
Wheel Offset Offset from the center line of the wheel to the King-pin.
Tread Width Width of the tire tread.
Chassis Overhang Distance of the center line of the front axle to the front edge of the cab. This does not include the bumper depth.
Additional Bumper Wheel Depth that the bumper assembly adds to the front overhang.
Wheelbase Distance between the center lines of the vehicles front and rear axles.
Inside Turning Radius Radius of the smallest circle around which the vehicle can turn.
Curb to Curb Turning Radius Radius of the smallest circle around which the vehicle's tires can turn. This measures assumes a curb height of 9 inches.
Wall to Wall Turning Radius Radius of the smallest circle around which the vehicle's tires can turn. This measures takes into account any front overhang due to chassis , bumper extensions and or aerial devices.
JROGHQVWDWHĆUHFRP
PRODUCT
WARRANTIES
Exhibit “C”
4 Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 2/8/2010 WA0008
1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL
OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,
INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.
2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.
This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.
THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE
TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.
No specific exclusions apply
Conditions and
Exclusions:
See Also
Paragraphs
2 thru 4
Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:
Fire and Rescue Apparatus
Coverage:
One (1) Year Material and Workmanship
Basic Apparatus
Twelve (12) months. Warranty Period
Ends After:
The date the apparatus is placed in service, or 60 days from the original buyer invoice date, whichever comes first. Warranty Begins:
Portions of the apparatus manufactured by Pierce shall be free from defects in material and workmanship
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;
4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.
Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,
INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,
WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW
OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY
PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS
THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,
REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.
If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.
Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.
3. BUYER'S EXCLUSIVE REMEDY.
Cummins Warranty
Worldwide
Fire Apparatus/Crash Trucks
Coverage
Products Warranted
This Warranty applies to new diesel Engines sold by
Cummins and delivered to the first user on or after
April 1, 2007, that are used in fire apparatus truck and crash truck* applications Worldwide.
Base Engine Warranty
The Base Engine Warranty covers any failures of the
Engine which result, under normal use and service,
from a defect in material or factory workmanship
(Warrantable Failure). This Coverage begins with the
sale of the Engine by Cummins and ends five years or
100,000 miles (160,935 kilometers), whichever occurs
first, after the date of delivery of the Engine to the first user.
Engine aftertreatment components included in the
Cummins Critical Parts List (CPL) and marked with a
Cummins part number are covered under Base Engine
Warranty.
Additional Coverage is outlined in the Emission
Warranty section.
These Warranties are made to all Owners in the
chain of distribution and Coverage continues to all
subsequent Owners until the end of the periods of
Coverage.
Cummins
Responsibilities
Cummins will pay for all parts and labor needed to
repair the damage to the Engine resulting from a
Warrantable Failure.
Cummins will pay for the lubricating oil, antifreeze,
filter elements, belts, hoses and other maintenance
items that are not reusable due to the Warrantable
Failure.
Cummins will pay for reasonable labor costs for
Engine removal and reinstallation when necessary to
repair a Warrantable Failure.
Cummins will pay reasonable costs for towing a
vehicle disabled by a Warrantable Failure to the
nearest authorized repair location. In lieu of the towing expense, Cummins will pay reasonable costs for
mechanics to travel to and from the location of the
vehicle, including meals, mileage and lodging when
the repair is performed at the site of the failure.
Owner
Responsibilities
Owner is responsible for the operation and
maintenance of the Engine as specified in Cummins
Operation and Maintenance Manuals. Owner is also
responsible for providing proof that all recommended
maintenance has been performed.
Before the expiration of the applicable Warranty,
Owner must notify a Cummins distributor, authorized
dealer or other repair location approved by Cummins
of any Warrantable Failure and make the Engine
available for repair by such facility. Except for Engines disabled by a Warrantable Failure, Owner must also
deliver the Engine to the repair facility.
Service locations are listed on the Cummins Worldwide
Service Locator at cummins.com.
Owner is responsible for the cost of lubricating oil,
antifreeze, filter elements and other maintenance items provided during Warranty repairs unless such items
are not reusable due to the Warrantable Failure.
Owner is responsible for communication expenses,
meals, lodging and similar costs incurred as a result of a Warrantable Failure.
Owner is responsible for non-Engine repairs and for
‘‘downtime’’ expenses, cargo damage, fines, all
applicable taxes, all business costs and other losses
resulting from a Warrantable Failure.
Owner is responsible for a $100 (U.S. Dollars)
deductible per each service visit under this plan in the 3rd, 4th and 5th years of Base Engine Warranty. The
deductible will not be charged during the first 2 years of the Base Engine Warranty.
Limitations
Cummins is not responsible for failures or damage
resulting from what Cummins determines to be abuse
or neglect, including, but not limited to: operation
without adequate coolants or lubricants; overfueling;
overspeeding; lack of maintenance of lubricating,
cooling or intake systems; improper storage, starting,
warm-up, run-in or shutdown practices; unauthorized
modifications of the Engine.
Any unauthorized modifications to the aftertreatment
could negatively effect emissions certification and void Warranty.
Cummins is also not responsible for failures caused by
incorrect oil, fuel or diesel exhaust fluid or by water, dirt or other contaminants in the fuel, oil or diesel
exhaust fluid.
This Warranty does not apply to accessories supplied
by Cummins which bear the name of another
company. Such non-warranted accessories include, but
are not limited to: alternators, starters, fans, air
conditioning compressors, clutches, filters,
transmissions, torque converters, vacuum pumps,
power steering pumps, fan drives and air compressors.
Cummins branded alternators and starters are covered
for the first two years from the date of delivery of the Engine to the first user, or the expiration of the Base Engine Warranty, whichever occurs first.
Failures resulting in excessive oil consumption are not covered beyond the duration of the Coverage or
100,000 miles (160,935 kilometers) or 7,000 hours from
the date of delivery of the Engine to the first user,
whichever of the three occurs first. Before a claim for excessive oil consumption will be considered, Owner
must submit adequate documentation to show that
consumption exceeds Cummins published standards.
Failures of belts and hoses supplied by Cummins are
not covered beyond the first year from the date of
delivery of the Engine to the first user or the duration of the Warranty, whichever occurs first.
Parts used to repair a Warrantable Failure may be new
Cummins parts, Cummins approved rebuilt parts or
repaired parts. Cummins is not responsible for failures resulting from the use of parts not approved by
Cummins.
A new Cummins or Cummins approved rebuilt part
used to repair a Warrantable Failure assumes the
identity of the part it replaced and is entitled to the remaining Coverage hereunder.
Cummins Inc. reserves the right to interrogate
Electronic Control Module (ECM) data for purposes of
failure analysis.
CUMMINS DOES NOT COVER WEAR OR WEAROUT
OF COVERED PARTS.
CUMMINS IS NOT RESPONSIBLE FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES.
THIS WARRANTY AND THE EMISSION WARRANTY
SET FORTH HEREINAFTER ARE THE SOLE
WARRANTIES MADE BY CUMMINS IN REGARD TO
THESE ENGINES. CUMMINS MAKES NO OTHER
WARRANTIES, EXPRESS OR IMPLIED, OR OF
MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE.
This Warranty gives you specific legal rights, and you
may also have other rights which vary from state to
state.
Emission
Warranty
Products Warranted
This Emission Warranty applies to new Engines
marketed by Cummins that are used in the United
States** in vehicles designed for transporting persons
or property on a street or highway. This Warranty
applies to Engines delivered to the first user on or after September 1, 1992.
Coverage
Cummins warrants to the first user and each
subsequent purchaser that the Engine is designed,
built and equipped so as to conform at the time of sale by Cummins with all U.S. federal emission regulations
applicable at the time of manufacture and that it is free from defects in material or factory workmanship which
would cause it not to meet these regulations within the longer of the following periods: (A) Five years or
100,000 miles (160,935 kilometers) of operation,
whichever occurs first, as measured from the date of
delivery of the Engine to the first user or (B) The Base Engine Warranty.
If the vehicle in which the Engine is installed is
registered in the state of California, a separate
California Emission Warranty also applies.
Limitations
Failures, other than those resulting from defects in
material or factory workmanship, are not covered by
this Warranty.
Cummins is not responsible for failures or damage
resulting from what Cummins determines to be abuse
or neglect, including, but not limited to: operation
without adequate coolants or lubricants; overfueling;
overspeeding; lack of maintenance of lubricating,
cooling or intake systems; improper storage, starting,
warm-up, run-in or shutdown practices; unauthorized
modifications of the Engine.
Any unauthorized modifications to the aftertreatment
could negatively effect emissions certification and void Warranty.
Cummins is also not responsible for failures caused by
incorrect oil, fuel or diesel exhaust fluid or by water, dirt or other contaminants in the fuel, oil or diesel
exhaust fluid.
Cummins is not responsible for non-Engine repairs,
‘‘downtime’’ expenses, cargo damage, fines, all
applicable taxes, all business costs or other losses
resulting from a Warrantable Failure.
Cummins Inc.
Box 3005
Columbus, IN 47202-3005
U.S.A.
Bulletin 3381161
Printed in U.S.A. Rev. 08/09
©2001 Cummins Inc.
CUMMINS IS NOT RESPONSIBLE FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES.
* Airport operated crash trucks and fire department
operated trucks employed to respond to fires,
hazardous material releases, rescue and other
emergency-type situations.
** United States includes American Samoa, the
Commonwealth of Northern Mariana Islands, Guam,
Puerto Rico and the U.S. Virgin Islands.
Cummins Inc.
Box 3005
Columbus, IN 47202-3005
U.S.A.
Bulletin 3381161
Printed in U.S.A. Rev. 08/09 2001 Cummins Inc.
Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 2/8/2010 WA0013
1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL
OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,
INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.
2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.
This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.
THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE
TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.
This warranty does not apply to damage caused by corrosion.
Conditions and
Exclusions:
See Also
Paragraphs
2 thru 4
Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:
Fire and Rescue Apparatus
Coverage:
Lifetime Fifty (50) Year Structural Integrity
Custom Chassis Frame
Fifty (50) Years
(Expected Life of Apparatus)
Warranty Period
Ends After:
The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:
Custom chassis frame rail manufactured by Pierce shall be free from defects in material and workmanship
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;
4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.
Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,
INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,
WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW
OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY
PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS
THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,
REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.
If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.
Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.
3. BUYER'S EXCLUSIVE REMEDY.
This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.
THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE
TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.
This limited warranty excludes brake pads, brake rotors, seal boots and shock absorbers.
Conditions and
Exclusions:
See Also
Paragraphs
2 thru 4
4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.
Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,
INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,
WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW
OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY
PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS
THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,
REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE
POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.
If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.
Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.
3. BUYER'S EXCLUSIVE REMEDY.
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce.
Three (3) Years
-or30,000 Miles
Warranty Period
Ends After:
Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 12/16/2013 WA0050
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES
ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,
INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.
2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.
Fire and Rescue Apparatus
Coverage:
Three (3) Year Material and Workmanship
TAK-4 Independent Front Suspension
Limited Warranty
Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:
The TAK-4 Front Independent Suspension and Steering
Gears shall be free from defects in material and
workmanship.
1. LIMITED WARRANTY
(b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:
Fire and Rescue Apparatus
Coverage:
SUPPLIER
Limited Warranty
Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:
The Meritor axle shall be covered by Meritor as indicated in the attached Meritor warranty coverage description
1. LIMITED WARRANTY
(b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the purchaser who first puts the product in service ("Buyer"):
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:
This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.
THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE
TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.
The exclusions listed in the attached Meritor warranty
description shall apply.
Conditions and
Exclusions:
See Also
Paragraphs
2 thru 4
4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.
Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,
INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,
WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW
OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY
PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS
THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,
REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.
If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.
Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.
3. BUYER'S EXCLUSIVE REMEDY.
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce.
Five (5) Years Warranty Period
Ends After:
Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 6/29/2020 WA0384
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL
OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,
INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.
2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.
CUMMINS-MERITOR
COMMERCIAL
VEHICLE SYSTEMS
WARRANTY
COVERAGE FOR THE
UNITED STATES AND CANADA
MODEL YEAR 2024 VEHICLES
2 WARRANTY INFORMATION
TABLE OF CONTENTS
EFFECTIVE MODEL YEAR 2024 VEHICLES
Linehaul.......................................................................................................3 General Service ...........................................................................................6 Heavy Service/Specialty Vehicle ..................................................................9 Fire and Emergency................................................................................... 12 Transit Bus ................................................................................................ 14 Off-highway Service................................................................................... 15 Terms and Conditions................................................................................ 17 How to Read Warranty Coverage
Number of Years Mileage (in thousands)
Unl = Unlimited
P = Parts Only
P&L = Parts and Labor
Notice:
Models or components that are approved for use by Cummins-Meritor’s vocational guidelines contained in Cummins-Meritor publication TP-9441 for axles, SP-8320 for trailer axles and TP-12126 for drivelines, or any other products that have an application approval completed with Cummins-Meritor which are not specifically listed, are warranted for one year, unlimited miles, parts only (1/Unl/P).
Products purchased on an incomplete vehicle (glider) are limited to one year, unlimited miles, parts only (1/Unl/P).
Advantage Program
Purchasing additional coverage on select components will continue to safeguard your investment against major repair costs after the initial base coverage expires. You can find out more about the Advantage Program by visiting meritor.com or by contacting Cummins-Meritor at 866-OnTrac1 (866-668-7221). 3 Linehaul Vehicles
Auto Hauler1
Bulk Hauler1
Chip Hauler1,2
Doubles
Flatbed
General Freight
Grain Hauler1
Livestock Hauler
Moving Van
Pipe Hauler
Refrigerated Freight
Tanker1
Triples
1 Cummins-Meritor classifies these vehicle types as high center of gravity, which require special axle housing considerations. 2 Chip Hauler vehicles require specific axle models listed below and Linehaul condition to be eligible for Linehaul warranty consideration.
Linehaul Typically Is:
High mileage operation (over 60,000 miles/year)
Greater than 30 miles between starts and stops
Maximum grades of 12%
Well maintained highways of concrete or asphalt construction (100% on-road)
Category A job sites, terminals, docks and transfer sites (defined as pavement, concrete or maintained and hard packed gravel).
Note:Category B job sites, terminals, docks, transfer sites (defined as loose or unmaintained sand, dirt or gravel; landfill; farm field; mud; or other similar surfaces) are NOT approved for certain linehaul axle models.
Front Non-Drive Steer Axles – 5/750/P&L
FD-965
FF-941
FF-942
FF-943
FF-944
FF-961
FF-966
FF-967
FG-941
FG-943
MFS-10-122A
MFS-10-143A-N
MFS-10-144A-N
MFS-12-122A-N
MFS-12-122B-N
MFS-12-122C-N
MFS-12E-122A-N
MFS-12E-122B-N
MFS-12E-122C-N
MFS-12-124A-N
MFS-12-132B-N
MFS-12-132C-N
MFS-12E-132B-N
MFS-12E-132C-N
MFS-12-143A-N
MFS-12E-143A-N
MFS-12-144A-N
MFS-13-122A-N
MFS-13-122B-N
MFS-13-122C-N
MFS-13-132B-N
MFS-13-132C-N
MFS-13-143A-N
MFS-13-144A-N
MFS-13B-122B-N
MFS-13B-122C-N
MFS-13B-132B-N
MFS-13B-132C-N
MFS-14-122A-N
MFS-14-122B-N
MFS-14F-122B-N
MFS-14G-122B-N
MFS-14-122C-N
MFS-14F-122C-N
MFS-14G-122C-N
MFS-14-124A-N
MFS-14-132B-N
MFS-14F-132B-N
MFS-14G-132B-N
MFS-14-132C-N
MFS-14F-132C-N
MFS-14G-132C-N
MFS-14-142B-N
MFS-14F-142B-N
MFS-14G-142B-N
MFS-14-142C-N
MFS-14F-142C-N
MFS-14G-142C-N
MFS-14-143A-N
MFS-14-144A-N
Rear Drive Single Axles – 5/750/P&L
MS-19-14X
RS-21-160
MS-23-17H1,2
MS-23-17X2
RS-23-160
RS-23-161
RS-23-185
RS-23-186
Coverage under Cummins-Meritor’s warranty require that
the application of products be properly approved pursuant to OEM and Cummins-Meritor approvals. Refer to TP-9441
for axles, SP-8320 for trailer axles, TP-12126 for drivelines and/or contact Cummins-Meritor regarding specific
application approval questions on any product line.
LINEHAUL
WARRANTY INFORMATION
Vocational Definition of Linehaul
Long distance hauling of food, goods and finished materials Not included are raw ferrous materials, minerals (except oil), sand, gravel, stone, rocks, topsoil, waste or logs Linehaul includes turnpike and hub & spoke
1 Not approved for use in any Category B job sites, terminals, docks or transfer sites. 2 Recommend 11 mm minimum wall thickness for these models used in combination with high center of gravity vehicles and trailing arm suspensions or vehicles operating mainly in Canada.
4 Trailer Axles1
Beam and Brackets 5/500/P, 1/100/L
TPX3000 Axle Series2 10/Unl/P, 1/Unl/L
Wheel End Systems3
Standard System4 1/100/P&L
AxlePak5 5/Unl/P&L
AxlePak75 7/Unl/P&L
1 For brake components and ABS coverage, refer to appropriate product warranties. 2 Structural components only excluding spindle wear. Spindle wear is 5/Unl/P, 1/Unl/L.
3 Includes hub, wheel seals and wheel bearings—all systems require annual inspections and proper documentation to ensure full coverage. 4 When installed by Cummins-Meritor. 5
When specified with AxlePak7 wheel end system, coverage on Meritor Tire Inflation System (MTIS) thru-tee and stator is 7/Unl/P, 1/Unl/L.
TAG/Pusher Axles1
TQ, TR Beam and Brackets 5/750/P&L
1 For brake components and ABS coverage, refer to appropriate product warranties.
Trailer Mechanical Suspension
Systems1
IMS40 (Integrated Mechanical Suspension – Tandem)2 1/Unl/P&L IMS20 (Integrated Mechanical Suspension – Single)2 1/Unl/P&L 1 For axle coverage, refer to appropriate product warranties. 2 All other suspension components refer to appropriate manufacturer’s warranty.
Trailer Air Suspension Systems
MPA40 (Tandem Axle Parallelogram)1
Major Structural Components 5/500/P, 1/100/L
Curbing Damage Warranty2 5/500/P, 1/100/L
Height Control Valve 1/100/P&L
Shock Absorbers 2/200/P&L
Air Springs 2/200/P, 1/100/L
Bushings 5/Unl/P, 3/Unl/L
PinLoc Air Controls 1/100/P&L
PinLoc Actuator 3/300/P&L
MPA20 (Single Axle Parallelogram)
Major Structural Components 5/500/P, 1/100/L
Height Control Valve 1/100/P&L
Shock Absorbers 2/200/P&L
Air Springs 2/200/P, 1/100/L
Bushings 5/Unl/P, 3/Unl/L
MTA and MTA-Tec6 Trailing Arm Suspension System
Major Structural Components 5/500/P, 1/100/L
Height Control Valve 1/100/P&L
Air Springs 2/200/P, 1/100/L
Bushings 5/500/P, 3/300/L
Shock Absorbers 2/200/P&L
Lift Kit System 1/100/P&L
1 Fastener torque coverage is limited to 2/Unl/P&L when torqued by CumminsMeritor (For axle and ABS coverage, refer to appropriate product warranties.) 2 “Curbing damage” is defined as deformation (bending, buckling or breakage), caused by sudden impact with a curb or similar fixed object. Damage to the RideSentry slider box (the suspension sliding sub-frame consisting of the frame rails, cross-members and central A-frame assembly), caused by accidental trailer impact with a curb or similar fixed object, is eligible for warranty coverage. Damage to other components or resulting from collision with another vehicle, rollover or fire is not covered under this provision. Warranty is not transferable to another trailer VIN and coverage does not apply if the trailer is deemed to be a total loss, scrapped or otherwise not salvageable.
LINEHAUL
WARRANTY INFORMATION
Rear Drive Tandem/Tridem Axles – 5/750/P&L
RT-40-160/P1,2
RT-46-160/P1,2
RT-46-164/P1,2
RZ-1662
RT-50-160/P1,2
MA-40-165
MA-40-17H3
RZ-188
MA-40-175
MT-34-14X/P4
MT-40-14T/P
MT-40-14X/P4
MT-40-14X/P4
MT-40-14H/E3,4
1 These models required for Chip Hauler and Linehaul warranty consideration. 2 Each vehicle must have a Request for Application Recommendation (RAR) approved by Cummins-Meritor prior to vehicle build. All RARs must identify the chassis number or VIN. Refer to Product Information Letter #303 and #396 for further details. 3 Not approved for use in any Category B job sites, terminals, docks or transfer sites. 4 Recommend 11 mm minimum wall thickness for these models used in combination with high center of gravity vehicles and trailing arm suspensions or vehicles operating mainly in Canada.
5 LINEHAUL
WARRANTY INFORMATION
Brake Components
Cam Q Series Trailer Brakes 5/500/P, 1/100/L
Q+ Drum Brake™1 5/500/P, 1/Unl/P&L
ASA 5/500/P, 1/Unl/P&L
Hubs/Cast Drums and Other Wheel-End Components 1/Unl/P
Hydraulic Disc Brakes 1/Unl/P
All Other Brakes 1/Unl/P
STEELite X30 Drum Brake™2 12-Years or Wearable Life/P
EX+ L and EX+LS Air Disc Brake™3 5/500/P, 1/Unl/L
EX+L Air Disc Brake Extended Standard Warranty3,4 5/500/P&L 1 For Trailer only, 3/300/P against rust jacking when equipped with Platinum Shield III. 2
Based on stamped wear diameter max. 3
Warranty coverage for boots, seals, caps, bushings and pins is 2/200/P.
Warranty coverage for pads is 1/100/P. 4
Applies only to calipers using friction: MA9300 (EX225LXXXCGXXX).
Drivelines
RPL 5/500/P, 1/Unl/P&L
MXL 3/350/P, 1/Unl/P&L
92N 1/Unl/P
Meritor Tire Inflation System
(MTIS)
MTIS Components 5/Unl/P, 1/Unl/L
6 General Service Vehicles
Auto Hauler
Beverage Truck
Bulk Hauler
Chip Hauler
Cross Country Coach
Flatbed
Front Engine Commercial
Chassis
Front Engine Integral Coach
General Freight
Grain Hauler
Intercity Coach
Intermodal Chassis
Livestock Hauler
Meat Packer
Moving Van
Municipal Truck
Newspaper Delivery
Pick-Up and Delivery
Pipe Hauler
Platform Auto Hauler
Rear Engine Integral Coach
Recreational Vehicles
Refrigerated Freight
School Bus
Stake Truck
Tanker
Tanker Trailer
Tour Bus
Wrecker
General Service Typically Is:
Typically, moderate mileage operation (less than 60,000 miles/year) An average of 3 to 30 miles between starts and stops
Maximum grades of 12%
Generally, on-road service (less than 10% off-road allowed) Category A job sites, terminals, docks and transfer sites (defined as pavement, concrete or maintained and hard packed gravel) or Category B job sites, terminals, docks and transfer sites (defined as loose or unmaintained sand, dirt or gravel; landfill; farm field; mud, or other similar surfaces)
Front Non-Drive Steer Axles – 2/Unl/P&L
FD-965
FF-941
FF-942
FF-943
FF-944
FF-946
FF-961
FF-966
FF-967
FG-941
FH-941
FH-9461
FL-941
FL-943
MFS-6-151A-N
MFS-6-153B-N
MFS-6-162B-N
MFS-6-153C-N
MFS-6-162C-N
MFS-7-113C-N
MFS-7-153C-N
MFS-7-163C-N
MFS-8-113B-N
MFS-8-143A-N
MFS-8-153B-N
MFS-8-163B-N
MFS-10-122A
MFS-10-143A-N
MFS-10-144A-N
MFS-12-122A-N
MFS-12E-122A-N
MFS-12-122B-N
MFS-12E-122B-N
MFS-12-122C-N
MFS-12E-122C-N
MFS-12-124A-N
MFS-12-132B-N
MFS-12E-132B-N
MFS-12-132C-N
MFS-12E-132C-N
MFS-12-143A-N
MFS-12-144A-N
MFS-12E-143A-N
MFS-13-122A-N
MFS-13-122B-N
MFS-13B-122B-N
MFS-13-122C-N
MFS-13B-122C-N
MFS-13-132B-N
MFS-13-132C-N
MFS-13B-132B-N
MFS-13B-132C-N
MFS-13-143A-N
MFS-13-144A-N
MFS-14-122A-N
MFS-14-122B-N
MFS-14F-122B-N
MFS-14G-122B-N
MFS-14-122C-N
MFS-14F-122C-N
MFS-14G-122C-N
MFS-14-124A-N
MFS-14-132B-N
MFS-14F-132B-N
MFS-14G-132B-N
MFS-14-132C-N
MFS-14F-132C-N
MFS-14G-132C-N
MFS-14-142B-N
MFS-14F-142B-N
MFS-14G-142B-N
MFS-14-142C-N
MFS-14F-142C-N
MFS-14G-142C-N
MFS-14-143A-N
MFS-14-144A-N
MFS-16-122A-N
MFS-16-133A-N
MFS-16-135A-N
MFS-16-143A-N
MFS-18-133A-N
MFS-18-135A-N
MFS-18-193A-N
MFS-20-133A-N
MFS-20-135A-N
MFS-20-192A-N
MFS-20-193A-N
MFS-22-135A-N
MFS-22H-135A-N
MFS-22-193A-N
MFS-22H-193A-N
1 Can also be used with reduced steer angles in tag position in Coach applications.
GENERAL SERVICE
WARRANTY INFORMATION
Coverage under Cummins-Meritor’s warranty require that
the application of products be properly approved pursuant to OEM and Cummins-Meritor approvals. Refer to TP-9441
for axles, SP-8320 for trailer axles, TP-12126 for drivelines and/or contact Cummins-Meritor regarding specific
application approval questions on any product line.
7 GENERAL SERVICE
WARRANTY INFORMATION
Rear Drive Tandem/Tridem Axles – 2/Unl/P&L
MT-34-14X/P
MT-40-14T/P
MT-40-14X/P
MT-44-14X/P
RT-46-169
MT-52-616
RT-52-1851
MT-58-616
RT-58-1851
MT-70-380
RZ-188
1 Each vehicle must have a Request for Application Recommendation (RAR) approved by Cummins-Meritor prior to vehicle build. All RARs must identify the chassis number or VIN. Refer to Product Information Letter #303 and #396 for further details.
Rear Drive Tandem/Tridem – 3/Unl/P&L
RT-40-160/P RT-46-160/P RT-46-164/P RT-50-160/P RZ-166
Rear Drive Axles – 1/Unl/P&L
RND-14H RND-16A
PTO – 1/Unl/P&L
MPT-170
MPT-180
MPT-185
MPT-309
MPT-500
MPT-518
MPT-1702
Brake Components
Cam Q Series Trailer Brakes1 3/Unl/P, 1/Unl/L
Cam P2 2/200/P
Cam 3/Unl/P
Q+ Drum Brake™ 3/Unl/P&L
Q+ Drum Brake™1,2 2/200/P&L
ASA 3/Unl/P
ASA2 2/200/P
Hubs/Cast Drums and Other Wheel-End Components 1/Unl/P
Hydraulic Disc Brakes 1/Unl/P
All Other Brakes 1/Unl/P
STEELite X30 Drum Brake™3 12-Years or Wearable Life/P
EX+ Air Disc Brake™4 2/Unl/P&L
1 For Trailer only, 3/300/P against rust jacking when equipped with Platinum Shield III or Chassis Protect. 2
Applies to Tour Bus and Cross Country Coach only. 3
Based on stamped wear diameter max. 4
Warranty coverage for boots, seals, caps, bushings and pins is 2/200/P.
Warranty coverage for pads is 1/100/P.
Drivelines
RPL 4/400/P, 1/Unl/P&L
MXL 3/350/P, 1/Unl/P&L
92N 1/Unl/P
Rear Drive Single Axles – 2/Unl/P&L
MS-17-13X
MS-17-14X
MS-19-13X
MS-19-14X
MS-21-13X
MS-21-14X
MS-23-17X
RS-21-160
RC-23-160
RC-23-161
RC-23-1621
RC-23-1651
RS-23-160
RS-23-161
RS-23-185
RS-23-186
RS-24-160
RC-25-160
RS-26-185
MS-26-616
MS-26-616-SP
RS-30-185
MS-30-616
MS-30-616-SP
RS-35-380
1 3/Unl/P&L if PreSet by Cummins-Meritor.
8 Trailer Axles1
Beam and Brackets2 5/Unl/P, 1/Unl/L
TPX4000 Axle Series3 10/Unl/P, 1/Unl/L
Wheel End Systems4
Standard System5 1/Unl/P&L
AxlePak5 5/Unl/P&L
AxlePak76 7/Unl/P&L
AxlePak107 10/Unl/P&L
1 For brake components and ABS coverage, refer to appropriate product warranties.
2 9000 Series is 3/Unl/P, 1/Unl/L
3 Structural components only excluding spindle wear. Spindle wear 5/Unl/P, 1/Unl/L. 4
Includes hub, wheel seals and wheel bearings—all systems require annual inspections and proper documentation to ensure full coverage. 5 When installed by Cummins-Meritor. 6
When specified with AxlePak7 wheel end system, coverage on Meritor Tire Inflation System (MTIS) thru-tee and stator is 7/Unl/P, 1/Unl/L. 7 AxlePak10 is limited to Intermodal Chassis applications equipped with TPX4000 series axles.
TAG/Pusher Axles1
TQ, TR Beam and Brackets 3/Unl/P, 1/Unl/L
MC14002, MC16003, FH9462 2/Unl/P&L
1 For brake components coverage, refer to appropriate product warranties. 2 3/Unl/P&L if sold with PreSet by Cummins-Meritor.
Meritor Tire Inflation System
(MTIS)
MTIS Components 5/Unl/P, 1/Unl/L
Trailer Mechanical Suspension
Systems1
IMS40 (Integrated Mechanical Suspension – Tandem)2 1/Unl/P&L IMS20 (Integrated Mechanical Suspension – Single)2 1/Unl/P&L 1 For axle coverage, refer to appropriate product warranties. 2 All other suspension components refer to appropriate manufacturer’s warranty.
Trailer Air Suspension Systems1
MPA40 (Tandem Axle Parallelogram)2
Major Structural Components 5/Unl/P, 1/Unl/L
Curbing Damage Warranty3 5/500/P, 1/100/L
Height Control Valve 1/Unl/P&L
Shock Absorbers 2/Unl/P&L
Air Springs 2/Unl/P, 1/Unl/L
Bushings 5/P, 3/L
PinLoc Air Controls 1/Unl/P&L
PinLoc Actuator 3/Unl/P&L
MPA20 (Single Axle Parallelogram)
Major Structural Components 5/Unl/P, 1/Unl/L
Height Control Valve 1/Unl/P&L
Shock Absorbers 2/Unl/P&L
Air Springs and Rebound Straps 2/Unl/P, 1/Unl/L
Bushings 5/P, 3/L
MTA and MTA-Tec6 Trailing Arm Suspension System
Major Structural Components 5/Unl/P, 1/Unl/L
Height Control Valve 1/Unl/P&L
Air Springs 2/Unl/P, 1/Unl/L
Bushings4 5/Unl/P, 3/Unl/L
Shock Absorbers 2/Unl/P&L
Lift Kit System 1/Unl/P&L
1 For axle coverage, refer to appropriate product warranties. 2 Fastener torque coverage is limited to 2/Unl/P&L when torqued by CumminsMeritor. 3 “Curbing damage” is defined as deformation (bending, buckling or breakage), caused by sudden impact with a curb or similar fixed object. Damage to the RideSentry slider box (the suspension sliding sub-frame, consisting of the frame rails, cross-members and central A-frame assembly), caused by accidental trailer impact with a curb or similar fixed object, is eligible for warranty coverage. Damage to other components or damage resulting from collision with another vehicle, rollover or fire is not covered under this provision. Warranty is not transferable to another trailer VIN and coverage does not apply if the trailer is deemed to be a total loss, scrapped or otherwise not salvageable. 4 Raw wood applications 3/Unl/P, 1/Unl/L
GENERAL SERVICE
WARRANTY INFORMATION
9 Heavy Service/Specialty Vehicles
Airport Rescue Fire
Fighting (ARFF)
Airport Shuttle1
Asphalt Truck
Block Truck
Bottom Dump Trailer
Combination
Cementing Vehicle
Commercial Pick-Up
Concrete Pumper
Construction Material Hauler
Mixer
Demolition
Drill Rig
Dump
Equipment Hauling
Flatbed Trailer Hauler
Flatbed Truck
Fracturing Truck
Front Loader
Geophysical Exploration
Hopper Trailer Combinations
Landscaping Truck
Liquid Waste Hauler
Log Hauling
Lowboy
Michigan Special Gravel
Train
Michigan Special Log Hauler
Michigan Special Steel
Hauler
Michigan Special Waste
Vehicle
Municipal Dump
Rear Loader (Refuse)
Recycling Truck
Residential Pick-Up (Refuse)
Rigging Truck
Roll-Off
Scrap Truck
Semi-End Dump
Sewer/Septic Vacuum
Shuttle Bus1
Side Loader
Snowplow/Snowblower
Steel Hauling
Tanker
Tank Truck
Tractors with Pole Trailers
Tractor/Trailer with Jeeps
Transfer Dump
Transfer Vehicle
Utility Truck
Winch Truck
1 Commercial chassis only
Heavy Service/Specialty Vehicle
Typically Is:
Moderate mileage operation (less than 60,000 miles per year) On/off-road vocations (10% or more off-road)
Moderate to frequent stops/starts (up to 10 stops per mile) An average of three (3) miles between starting and stopping Front Non-Drive Steer Axles – 2/Unl/P&L
FD-965
FF-941
FF-942
FF-943
FF-944
FF-946
FF-961
FF-966
FF-967
FG-941
FG-943
FH-941
FH-946
FL-941
FL-943
MFS-6-151A-N
MFS-6-153B
MFS-6-162B
MFS-6-162C
MFS-7-113C-N
MFS-7-153C-N
MFS-7-163C-N
MFS-8-113B-N
MFS-8-153B-N
MFS-8-163B-N
MFS-10-122A
MFS-10-143A-N
MFS-10-144A-N
MFS-12-122
MFS-12E-122
MFS-12-122B-N
MFS-12E-122B-N
MFS-12-122C-N
MFS-12E-122C-N
MFS-12-124A-N
MFS-12-132B-N
MFS-12E-132B-N
MFS-12-132C-N
MFS-12E-132C-N
MFS-12-143A-N
MFS-12-144A-N
MFS-12-155
MFS-13-122
MFS-13-122B-N
MFS-13B-122B-N
MFS-13-122C-N
MFS-13B-122C-N
MFS-13-132B-N
MFS-13B-132B-N
MFS-13-132C-N
MFS-13B-132C-N
MFS-13-143A-N
MFS-13-144A-N
MFS-13-155
MFS-14-122
MFS-14-122B-N
MFS-14F-122B-N
MFS-14G-122B-N
MFS-14-122C-N
MFS-14F-122C-N
MFS-14G-122C-N
MFS-14-124A-N
MFS-14-132B-N
MFS-14F-132B-N
MFS-14G-132B-N
MFS-14-132C-N
MFS-14F-132C-N
MFS-14G-132C-N
MFS-14-142B-N
MFS-14F-142B-N
MFS-14G-142B-N
MFS-14-142C-N
MFS-14F-142C-N
MFS-14G-142C-N
MFS-14-143A-N
MFS-14-144A-N
MFS-16-122A-N
MFS-16-133A-N
MFS-16-135A-N
MFS-16-143A-N
MFS-18-133A-N
MFS-18-135A-N
MFS-18-192A-N
MFS-18-193A-N
MFS-20-133A-N
MFS-20-135A-N
MFS-20-192A-N
MFS-20-193A-N
MFS-22-135A-N
MFS-22H-135A-N
MFS-22-193A-N
MFS-22H-193A-N
RF-16-145
RF-21-160
HEAVY SERVICE/SPECIALTY VEHICLE
WARRANTY INFORMATION
Coverage under Cummins-Meritor’s warranty require that
the application of products be properly approved pursuant to OEM and Cummins-Meritor approvals. Refer to TP-9441
for axles, SP-8320 for trailer axles, TP-12126 for drivelines and/or contact Cummins-Meritor regarding specific
application approval questions on any product line.
10 Rear Drive Axles – 2/Unl/P&L
MS-17-14X
MS-19-14X
MS-21-14X
RS-21-160
RC-23-160
RH-23-160
RS-23-160
RC-23-161
RS-23-161
RS-23-185
RS-23-186/380
RS-24-160
RC-25-160
RS-25-160
MS-26-616
MS-26-616-SP
RS-26-185/380
RC-26-633
MS-30-616
MS-30-616-SP
RS-30-185/380
MS-35-380
RS-38-380
MT-58-616
MT-58-616-SP
Rear Drive Axles – 1/Unl/P&L
RND-14H RND-16A
Rear Drive Tandem/Tridem Axles – 2/Unl/P&L
MT-34-14X/P
MT-40-14T/P
MT-40-14X/P
MT-44-14X/P
RT-46-169
RT-58-160
MT-52-616
MT-52-616-SP
RT-52-185/3801,2
MT-58-616
MT-58-616-SP
RT-58-185/3801,2
RT-70-380
MT-70-380
RZ-188
1 Axle model designated will vary according to options and variations specified on these axles. Contact Cummins-Meritor Axle Applications Engineering for details. 2 Each vehicle must have a Request for Application Recommendation (RAR) approved by Cummins-Meritor prior to vehicle build. All RARs must identify the chassis number or VIN. Refer to Product Information Letter #303 and #396 for further details.
Rear Drive Tandem/Tridem – 3/Unl/P&L
RT-40-160/P/A3 RT-46-160/P/A1,3 RT-46-164/P2,3 RT-50-160/P/A3 RZ-166 1 U.S. only. Canadian warranty = 1/Unl/P for combination vehicles only. 2 Axle model designated will vary according to options and variations specified on these axles. Contact Cummins-Meritor Axle Applications Engineering for details. 3 Each vehicle must have a Request for Application Recommendation (RAR) approved by Cummins-Meritor prior to vehicle build. All RARs must identify the chassis number or VIN. Refer to Product Information Letter #303 and #396 for further details.
Front Drive Steer Axles – 1/Unl/P&L
MX-08-130-FV (FSD-08A)
MX-10-130-FV (FSD-10A)
MX-12-130-FV (FSD-12A)
MX-13-130-FV (FSD-13A)
MX-14-130-FV (FSD-14A)
MX-16-130-FV (FSD-16A)
MX-18-130-FV (FSD-18A)
MX-18-130-SD (SDA-1800)
MX-20-130-FV (FSD-20A)
MX-21-130-FV (FSD-21A)
MX-21-130-SD (SDA-2100)
MX-23-130-FV (FSD-23A)
MX-23-130-SD (SDA-2300)
HEAVY SERVICE/SPECIALTY VEHICLE
WARRANTY INFORMATION
MX-10-120
MX-10-120 EVO
MX-12-120
MX-12-120 EVO
MX-14-120
MX-14-120 EVO
MX-16-120
MX-18-120
MX-17-140
MX-19-140
MX-21-140
MX-21-160
MX-23-160
MX-23-810
Front Drive Steer Axles – 2/Unl/P&L
MPT-170
MPT-180
MPT-185
MPT-309
MPT-500
MPT-518
MPT-1702
PTO – 1/Unl/P&L
11 Drivelines
RPL 3/Unl/P, 1/Unl/P&L
92N 1/Unl/P&L
MXL 1/Unl/P&L
Transmission – 1/Unl/P&L
FAT 30
Brake Components
Cam P 3/Unl/P
Cam P 2/100/P
Cam Cast Plus™ 2/100/P&L
Q+ Drum Brake™1 3/Unl/P&L
Q+ Drum Brake™2 2/100/P&L
ASA 3/Unl/P
ASA2 2/100/P
Hubs/Cast Drums and Other Wheel-End Components3 1/Unl/P Hydraulic Disc Brakes 1/Unl/P
All Other Brakes 1/Unl/P
EX+ Air Disc Brake4 2/100/P&L
1 For Trailer only, 3/300/P against rust jacking when equipped with Platinum Shield III. 2
Applies to City Bus, Trolley, Shuttle Bus and Airport Shuttle only. 3 Based on stamped wear diameter max. 4
Warranty coverage for boots, seals, caps, bushings and pins is 2/100/P.
Warranty coverage for pads is 1/100/P.
Trailer Axles1
Beam and Brackets2 5/Unl/P, 1/Unl/L
Wheel End Systems3
Standard System4 1/Unl/P&L
1 For brake components coverage, refer to appropriate product warranties. 2 9000 Series is 3/Unl/P, 1/Unl/L 3 Includes hub, wheel seals and wheel bearings—all systems require annual inspections and proper documentation to ensure full coverage. 4 When installed by Cummins-Meritor.
Trailer Air Suspension Systems1
MTA and MTA-Tec6 Trailing Arm Suspension System
Major Structural Components2 5/500/P, 1/100/L
Height Control Valve 1/100/P&L
Air Springs 2/200/P, 1/100/L
Bushings2 5/500/P, 3/300/L
Shock Absorbers 2/200/P&L
Lift Kit System 1/100/P&L
1 For axle coverage, refer to appropriate product warranties. 2 Raw wood applications 3/Unl/P, 1/Unl/L
Meritor Tire Inflation System
(MTIS)
MTIS Components 5/Unl/P, 1/Unl/L
Gearboxes – 1/Unl/P&L
MGX-402
MGX-423
MGX-450
MGX-451
MGX-466
MGX-479
MGX-538
Transfer Cases – 1/Unl/P
MTC-2212-CV (306)
MTC-3106-FV (TC-137)
MTC-3111 (T-2111)
MTC-3112-CV (548C)
MTC-3116 (T-2111 through-shaft)
MTC-3118-FV (TC-180 and TC-180-23)
MTC-3118-CV (358)
MTC-3120-FV (TC-143)
MTC-3124 (T-2119)
MTC-3203
MTC-3205-GV (MTC-25/RTC-25)
MTC-3206-FV (TC-237)
MTC-3206-CS (544)
MTC-3208-GV (RTC-50)
MTC-3209-GV (MTC-60/RTC-60)
MTC-3212-CV (315 and 548B)
MTC-3312-FV (TC-270)
MTC-3220-FC (TC-142)
MTC-4206-FV (TC-38)
MTC-4208
MTC-4210
MTC-4213
HEAVY SERVICE/SPECIALTY VEHICLE
WARRANTY INFORMATION
12 Fire and Emergency Vehicles
Aerial Ladder Truck
Aerial Platform
Ambulance
Command Vehicle
Crash Fire Rescue
Pumper
Rapid Intervention
Vehicle (RIV)
Tanker
Fire and Emergency Typically Is:
Lower mileage operations (less than 20,000 miles/year)
Generally, on-road service (less than 10% off-road)
An average of three (3) miles between starting and stopping Front Non-Drive Steer Axles – 5/Unl/P&L
FL-941
FL-943
MFS-18-133A-N
MFS-18-135A-N
MFS-18-193A-N
MFS-20-133A-N
MFS-20-135A-N
MFS-20-193A-N
MFS-22-135A-N
MFS-22H-135A-N
MFS-22-193A-N
MFS-22H-193A-N
Rear Drive Single Axles – 5/Unl/P&L
RC-23-160
RS-23-160
RS-23-161
RS-23-185
RS-23-186
RS-24-160
RC-25-160
RS-26-185
RS-30-185
RS-35-1851
RS-25-160
1 2/Unl/P&L if PreSet by Cummins-Meritor.
Rear Drive Tandem/Tridem Axles – 5/Unl/P&L
MT-40-14X/P
RT-40-160/P
MT-44-14X/P
RT-46-160/P
RT-46-164/P
RT-46-169
RT-50-160/P
MT-52-616
RT-52-1851
MT-58-616
RT-58-1851
MT-70-3802
1 Each vehicle must have a Request for Application Recommendation (RAR) approved by Cummins-Meritor prior to vehicle build. All RARs must identify the chassis number or VIN. Refer to Product Information Letter #303 and #396 for further details. 2 2/Unl/P&L Front Drive Steer Axles – 2/Unl/P&L
MX-19-140 MX-21-140 MX-21-160 MX-23-160 MX-23-810
FIRE AND EMERGENCY
WARRANTY INFORMATION
Coverage under Cummins-Meritor’s warranty require
that the application of products be properly approved
pursuant to OEM and Cummins-Meritor approvals.
Refer to TP-9441 for axles, TP-12126 for drivelines
and/or contact Cummins-Meritor regarding specific
application approval questions on any product line.
Transfer Cases – 1/Unl/P
MTC-2212-CV (306)
MTC-3106-FV (TC-137)
MTC-3111 (T-2111 through-shaft)
MTC-3112-CV (548C)
MTC-3118-FV (TC-180 and TC-180-23)
MTC-3118-CV (358)
MTC-3120-FV (TC-143)
MTC-3124 (T-2119)
MTC-3206-FV (TC-237)
MTC-3206-CS (544)
MTC-3208-GV (RTC-50)
MTC-3209-GV (MTC-60/RTC-60)
MTC-3212-CV (315 and 548B)
MTC-3312-FV (TC-270)
MTC-3220-FC (TC-142)
MTC-4206-FV (TC-38)
MTC-4208
MTC-4210
MTC-4213
13 PTO – 1/Unl/P&L
MPT-170
MPT-180
MPT-185
MPT-309
MPT-500
MPT-518
MPT-1702
FIRE AND EMERGENCY
WARRANTY INFORMATION
Brake Components
Cam 3/Unl/P
Q+ Drum Brake™ 3/Unl/P&L
ASA 3/Unl/P
Hubs/Cast Drums and Other Wheel-End Components 1/Unl/P
Hydraulic Disc Brakes 1/Unl/P
All Other Brakes 1/Unl/P
EX+ Air Disc Brake™1 2/Unl/P&L
1 Warranty coverage for boots, seals, caps, bushings and pins is 2/200/P.
Warranty coverage for pads is 1/100/P.
Drivelines
RPL 4/400/P, 1/Unl/L
MXL 3/350/P, 1/Unl/L
92N 1/Unl/P
14 Transit Bus Vehicles
Airport Shuttle
City Bus
Commuter Coach
Shuttle Bus
Transit Bus Trolley
Transit Bus Typically Is:
Moderate mileage operation (less than 50,000 miles per year) Moderate to frequent stops/starts (up to 10 stops per mile) Front Non-Drive Steer Axles – 5/300/P&L
FH-946 FH-9411 MFS-12-155 MFS-13-155
1 Commuter coach only – 2/Unl/P&L
Tag Axles – 2/Unl/P&L
Brake Components
Cam Cast Plus™ 2/100/P&L
Q+ Drum Brake™1 2/100/P&L
ASA1 2/100/P
Hubs/Cast Drums and Other Wheel-End Components 1/Unl/P
All Other Brakes 1/Unl/P
EX+ Air Disc Brake2 2/100/P&L
1 Applies to City Bus, Trolley, Shuttle Bus and Airport Shuttle only. 2 Warranty coverage for boots, seals, caps, bushings and pins is 2/100/P.
Warranty coverage for pads is 1/100/P.
Drivelines
RPL 3/Unl/P, 1/Unl/L
92N 1/Unl/P&L
MXL 1/Unl/P&L
1 Commuter coach only – 2/Unl/P&L
Rear Drive Single Axles – 5/300/P&L
RS-23-160
RC-23-161
71163
79163
RC-23-1621
RC-23-1651
RS-21-160
MC-14002 MC-16003 FH-946
Center Non-drive Axles – 5/300/P&L
MC-26000 71063 79063
Gearboxes – 1/Unl/P&L
MGX-450 MGX-451 MGX-538
TRANSIT BUS
WARRANTY INFORMATION
Coverage under Cummins-Meritor’s warranty require
that the application of products be properly approved
pursuant to OEM and Cummins-Meritor approvals.
Refer to TP-9441 for axles, TP-12126 for drivelines
and/or contact Cummins-Meritor regarding specific
application approval questions on any product line.
15 Industrial and Off-Highway Service Vehicles
Load-On/Load-Off
Port Tractor
Rail Yard Spotter
Roll-On/Roll-Off
Stevedoring Tractor
Trailer Spotter
Yard Jockey
All and Rough
Terrain Cranes
Forestry
Material Handling
Specialized Heavy
Haul
Excavator
Compactor
Fertilizer Spreader
Snow Blower
Mining and
Specialized Mining
Rail Car Mover
Loader
Tow Tractor
Pushback Tractor
Industrial and Off-Highway Service Typically Is:
Low mileage operation
Low speed vehicle speed restriction
Vehicles are not typically licensed for highway use
Six (6) starts/stops per mile (typical)
Front Non-Drive Steer Axles – 1/Unl/P
FF - 941
FF - 943
FF - 961
FF - 966
FG - 941
FG - 943
FL - 941
FL - 943
FN - 951
FS-25
MFS-20-133A-N
MFS-20-135A-N
MFS-20-192A-N
MFS-20-193A-N
MFS-22-135A-N
MFS-22H-135A-N
MFS-22-193A-N
MFS-22H-193A-N
MON-Z0 FAMILY
Gearboxes – 1/Unl/P&L
MGX-402
MGX-423
MGX-450
MGX-451
MGX-466
MGX-479
MGX-538
PTO – 1/Unl/P&L
MPT-170
MPT-180
MPT-185
MPT-309
MPT-500
MPT-518
MPT-1702
1 2/Unl/P for LO/LO Terminal Tractor applications
Planetary Axles – 1/Unl/P
MOB
MOC
MOD
MOE
MOF
MOG
MOH
MOR
MOS
MOT
MOX
MOY
MOZ
Rear Drive Axles – 1/Unl/P
MT-14X1
RS-23-186
RS-23-380
RS-24-160
RS-30-185
RS-30-380
RT-1451
RT-1601
OFF-HIGHWAY SERVICE
WARRANTY INFORMATION
Coverage under Cummins-Meritor’s warranty require that the application of products be properly approved pursuant to OEM and Cummins-Meritor approvals. Contact Cummins-Meritor regarding specific application approval questions on any product line. 16 Drivelines – 1/Unl/P
RPL MXL
Transmission – 1/Unl/P&L
FAT 30
Brake Components
Cam 3/Unl/P
Q+ Drum Brake™ 3/Unl/P&L
ASA 3/Unl/P
Hubs/Cast Drums and Other Wheel-End Components 1/Unl/P
Hydraulic Disc Brakes 1/Unl/P
All Other Brakes 1/Unl/P
OFF-HIGHWAY SERVICE
WARRANTY INFORMATION
Transfer Cases – 1/Unl/P
MTC-2212-CV (306)
MTC-3106-FV (TC-137)
MTC-3111 (T-2111 through-shaft)
MTC-3112-CV (548C)
MTC-3116 (T-2111)
MTC-3118-FV (TC-180 and TC-180-23)
MTC-3118-CV (358)
MTC-3120-FV (TC-143)
MTC-3124 (T-2119)
MTC-3206-FV (TC-237)
MTC-3208-GV (RTC-50)
MTC-3209-GV (MTC-60/RTC-60)
MTC-3220-FC (TC-142)
17 Coverage Exclusions
Product Description
All
The cost of any repairs, replacements or adjustments to a covered component (1) associated with noise; (2) resulting from the use or installation of non-genuine Cummins-Meritor components or materials; (3) due to vibration associated with improper operation or misapplication of drivetrain components; and (4) damage resulting from corrosion.
For axle assemblies supplied by Cummins-Meritor with suspension and interface brackets designed and/or attached by nonCummins-Meritor parties, Cummins-Meritor warranty coverage does not apply to the brackets, bracket attachment methods and field issues caused by brackets or bracket attachments to any covered component unless specified in a separate OEM agreement.
Front Axles1
Linehaul – King Pin Bushings 1yr/Unl P&L
All Other Vocations – King Pin Bushings Excluded
1 King Pin Bushing wear excluded for all vocations.
Rear Axles
Self-contained traction equalizers and oil filters. The use of NoSPIN differentials will result in the exclusion of axle shafts from warranty considerations. NoSPIN is a product of Eaton.
ASA
Boot and bushing. Bent, broken, over-torqued, missing or otherwise damaged pawl assemblies.
Cam Brake
Brake lining wear and brake shoe “rust-jacking.”
Disc Brake
Pad wear, rotor wear.
Coverage Limitations
Product Description
All
Any claim beyond 60 days from date of repair will not be accepted or honored under this warranty program. Products purchased on an incomplete vehicle (glider) are limited to one year, unlimited miles parts only (1/Unl/P).
Warranty coverage on vehicles with 1,850 lb-ft engine torque and over may be reduced on individual drivetrain components. Contact your Cummins-Meritor representative for specific details.
Front Axles
Tie rod and tie rod ends limited to 3-year/300,000-mile or published vocational coverage, whichever is less. Wheel seals, gaskets and wheel bearings are covered for 1 year/unlimited miles if the wheel end equipment is supplied and assembled by Cummins-Meritor.
Rear Axles
Pinion and through shaft seals limited to 3-year/300,000-mile or published vocational coverage, whichever is less, if yoke is installed by Cummins-Meritor. If yoke is not installed by CumminsMeritor, then Cummins-Meritor does not warrant pinion seals.
Wheel seals, gaskets and wheel bearings are covered for 1 year/unlimited miles if the wheel end equipment is supplied and assembled by Cummins-Meritor.
Rear Axles
The Cummins-Meritor breather part number A-2297-C-8765 with A-3196-J-1336 hose must be used for eligibility of any potential warranty consideration relating to contamination and/or loss of lube in axles.
Cam Brake
Limited to bracket, brake spider and camshaft structural integrity.
STEELite X30
Wearable life is up to the discard diameter of the drum.
Terms and Conditions
(1) What is Covered by this Commercial Warranty?
Meritor Heavy Vehicle Systems, LLC warrants to the owner (“Owner”) that the components listed in this publication, which have been installed by an Original Equipment Manufacturer (“OEM”) as original equipment in vehicles licensed for on-highway use, will be free from defects in material and workmanship. This warranty coverage begins only after the expiration of the OEM’s vehicle warranty for the applicable covered components. Warranty coverage ends at the expiration of the applicable time period from the date of vehicle purchase by the first Owner or the applicable mileage limitation, whichever occurs first. Duration of coverage varies by component and vocation as detailed elsewhere in this warranty statement.
Some components are warranted for parts only and the Owner must pay any labor costs associated with the repair or replacement of the component.
Other components are warranted for both parts and reasonable labor to repair or replace the subject component. Components (whether new, used or remanufactured) installed as replacements under this warranty are warranted only for the remainder of the original period of time or mileage under the original warranty.
For certain components, coverage requires the use of specific extended drain interval or synthetic lubricants. For further information about lubrication and maintenance, see Cummins-Meritor publication Maintenance Manual Number l and the applicable Cummins-Meritor maintenance manual for the product in question. Other conditions and limitations applicable to this warranty are detailed below.
TERMS AND CONDITIONS
Product models, brands, names and trademarks depicted herein are the property of their respective owners and, except where otherwise indicated, are not in any way associated with Meritor Heavy Vehicle Systems, LLC, or any parent or affiliate, thereof. (2) Designation of Vocational Use Required
To obtain warranty coverage, each Owner must notify Cummins-Meritor through the OEM new truck and/or trailer dealer of the intended vocational use of the vehicle into which the Cummins-Meritor components have been incorporated prior to the vehicle in-service date. This notification may be accomplished by registering the vehicle through your OEM new truck and/or trailer dealer or with Cummins-Meritor directly. Failure to notify CumminsMeritor of (I) the intended vocational use of the vehicle or (II) a change in vocational use from that which was originally designated, will result in the application of a one year, unlimited mileage, parts only warranty (1/Unl/P) from the initial in-service date.
A second Owner and each subsequent Owner must also notify CumminsMeritor as to the intended vocational use of the vehicle. This notification can be sent directly to Cummins-Meritor or through the OEM new truck and/ or trailer dealer. The duration and mileage coverage of this warranty cannot exceed the coverage extended to the first Owner after his or her initial designation of vocational use.
Coverage under Cummins-Meritor’s warranty requires that the application of products be properly approved pursuant to OEM and Cummins-Meritor approvals. Refer to TP-9441 for axles, SP-8320 for trailer axles, TP-12126 for drivelines and/or contact Cummins-Meritor regarding specific application approval questions on any product line.
(3) What is the Cost of this Warranty?
There is no charge to the Owner for this warranty.
(4) What is not Covered by this Warranty?
This warranty does not cover normal wear and tear; nor does it cover a component that fails, malfunctions or is damaged as a result of (I) improper installation, adjustment, repair or modification (including the use of unauthorized attachments or changes or modification in the vehicle’s configuration, usage or vocation from that which was originally approved by Cummins-Meritor), (II) accident, natural disaster, abuse or improper use (including loading beyond the specified maximum vehicle weight or altering engine power settings to exceed the axle and/or driveline capacity) or (III) improper or insufficient maintenance (including deviation from approved lubricants, change intervals or lube levels). This warranty does not cover any component or part that is not branded by Cummins-Meritor. For vehicles that operate full or part time outside of the United States and Canada, a one year, unlimited mileage, parts only warranty (1/Unl/P) will apply.
(5) Remedy
The exclusive remedy under this warranty shall be the repair or replacement of the defective component at Cummins-Meritor’s option. Cummins-Meritor reserves the right to require that all applicable failed materials are available and/or returned to Cummins-Meritor for review and evaluation. (6) Disclaimer of Warranty
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES
OR CONDITIONS, EXPRESSED, IMPLIED OR STATUTORY INCLUDING
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
PARTICULAR PURPOSE.
(7) Limitation of Remedies
In no event shall Cummins-Meritor be liable for special, incidental, indirect or consequential damages of any kind or under any legal theory, including, but not limited to, towing, downtime, lost productivity, cargo damage, taxes or any other losses or costs resulting from a defective covered component. (8) To Obtain Service
If the Owner discovers within the applicable coverage period a defect in material or workmanship, the Owner must promptly give notice to either Cummins-Meritor or the dealer from which the vehicle was purchased. To obtain service, the vehicle must be taken to any participating OEM new truck and/or trailer dealer or authorized Cummins-Meritor service location. The dealer will inspect the vehicle and contact Cummins-Meritor for an evaluation of the claim. When authorized by Cummins-Meritor, the dealer will repair or replace during the term of this warranty any defective Cummins-Meritor component covered by this warranty.
(9) Entire Agreement
This is the entire agreement between Cummins-Meritor and the Owner about warranty and no Cummins-Meritor employee or dealer is authorized to make any additional warranty on behalf of Cummins-Meritor. This agreement allocates the responsibilities for component failure between Cummins-Meritor and the Owner.
TERMS AND CONDITIONS
Cummins Inc.
Box 3005
Columbus, IN 47202-3005
U.S.A.
cummins.com
SP-95155
Bulletin 6451105 Produced in U.S.A. Rev. 1/24
©2024 Meritor, Inc.
)LUHDQG5HVFXH$SSDUDWXV
Coverage:
7KUHH
<HDU0DWHULDODQG:RUNPDQVKLS
0HULWRU:DEFR$%6%UDNH6\VWHP
Limited Warranty
Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:
The Meritor Wabco ABS brake system shall be covered by
Meritor Wabco as indicated in the attached Meritor Wabco warranty coverage description
/,0,7(':$55$17<
(b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce.
Three (3) Year Warranty Period
Ends After:
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.
THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE
TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.
The exclusions listed in the attached Meritor Wabco warranty description shall apply.
Conditions and
Exclusions:
See Also
Paragraphs
2 thru 4
(;&/86,212)&216(48(17,$/$1',1&,'(17$/'$0$*(6
Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,
INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,
WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW
OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY
PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS
THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,
REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE
POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.
If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.
Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.
%8<(5
6(;&/86,9(5(0('<
Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 2/25/2013 WA0232
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES
ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,
INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.
',6&/$,0(562):$55$17,(6
capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.
WARRANTY
Warranty coverage is essential to protecting your investment. But understanding the full details of your coverage can be challenging. This straightforward approach allows you, our valued customer, to better understand how your specific vehicle applications will be covered in your region. Our component warranty coverage is provided according to vocation/usage categories listed below. • Linehaul covers high mileage operation (over 60,000 miles/year) on well-maintained major highways of concrete or asphalt construction.
• General Service covers moderate mileage operations (less than 60,000 miles/year) on well-maintained public roads (less than 10 percent off-road) typically with less than three (3) stops per mile. • Heavy Service (Vocational) covers vehicles with more than 10 percent off-road OR moderate to frequent starts/stops typically with more than three (3) stops per mile.
• Off-Highway Service covers lower mileage operations. Vehicles are not typically licensed for highway use. • The standard aftermarket warranty for WABCO products - including WABCO Original parts, WABCO Reman Solutions, ProVia quality aftermarket parts and WABCO retrofit solutions - is one year, parts only from in-service date when purchased from ZF distributor networks or its affiliates and/or subsidiaries.
MODEL YEAR 2021 VEHICLES
How to Read Warranty Coverage (Example)
Number of Years Mileage (in thousands) Unl=Unlimited P=Parts Only P&L=Parts & Labor 3 300 P
WARRANTY - MODEL YEAR 2021 VEHICLES
¹ ZF and WABCO branded components. 2
WABCO compressors installed on Cummins, Mercedes, and DDC engines are not warranted or serviced by ZF. Please contact your respective dealer/distributor of those engines for warranty and servicing. 3 An extended warranty of 4/400/P will apply when a WABCO Trailer Control Line Filter is used in combination with a WABCO Trailer ABS valve.
• Aerial Ladder Truck
• Aerial Platform
• Ambulance
• Auto Hauler
• Beverage Truck
• Bulk Hauler
• Chip Hauler (Truck)
• Cross Country Coach
• Doubles
• Flatbed
• Front Engine Commercial
Chassis
• Front Engine Integral
Coach
• General Freight
• Grain Hauler
• Intercity Coach
• Intermodal Chassis
• Livestock Hauler
• Meat Packer
• Moving Van
• Municipal Truck
• Pipe Hauler
• Platform Auto Hauler
• Pumper
• Rear Engine Integral Coach
• Recreational Vehicles
• Refrigerated Freight
• School Bus
• Stake Truck
• Tanker
• Tanker Truck
• Triples
• Tour Bus
• Wrecker
LINEHAUL/GENERAL SERVICE VEHICLES
LINEHAUL/GENERAL SERVICE WARRANTY INFORMATION
LINEHAUL TYPICALLY IS
• High mileage operation (over 60,000 miles/year)
• Well maintained major highways of concrete or
asphalt construction
GENERAL SERVICE TYPICALLY IS
• Moderate mileage operations (less than 60,000 miles/year) • Well maintained public roads (less than 10% off-road) • Less than three (3) stops per mile
WABCO Components1
Air Management
Air Brake Valves
Trailer Lift Axle Control Valve 1/100/P&L
Trailer Control Line Filter3
Air Compressors (ALL)2 2/200/P&L
Air Dryers (ALL) 3/300/P&L
Aerodynamics
OptiFlow® TrailerSkirt 2/UnU/P
OptiFlow® Trailer Tail and AutoTail 2/UnI/P
Braking Systems
ABS (Anti-Lock Braking System) Air
3/300/P&L
ABS (Anti-Lock Braking System) Hydraulic
Electronic Braking System (EBS)
Electronic Stability Control (ESC)
Roll Stability Control (RSS)
Trailer Roll Stability Support (RSS)
Trailer ABS (Anti-Lock Braking System)3
Driveline Suspension Control
Clutch Controls 2/200/P&L
Leveling Valves
1/100/P&L
OptiRide® Automated Manual Transmission (AMT)
OptiRide® Electronically Controlled Air Suspension
(ECAS) 3/300/P&L
WABCO Components1 (cont.)
Safety
OnGuardACTIVE®
3/300/P&L
OnLane®
OnLaneALERT®
OnSide®
Trailer SafeStart™
Trailer TailGUARD™
Telematics
TrailerCAST™ Telematics Device 3/300/P&L
Wheel End Solutions
EasyFit™ Slack Adjuster 6/600/P
MAXXUS™ Truck Air Disc Brake 5/500/P&L
IVTM - Wheel Module 6/P
IVTM - All Other Products 2/P
Pan 17 and 19 Air Disc Brake 2/Unl/P and
1/Unl/L
Pan 22 Air Disc Brake 5/500/P and 1/L
TRISTOP™ D Actuator w/ IBV or IRB 6/600/P
TRISTOP™ D Actuator 3/300/P
UNISTOP™ Actuator 2/200/P
Trailer MAXX22T™ Air Disc Brake 5/500/P and 1/L
1 ZF and WABCO branded components. 2 WABCO compressors installed on Cummins, Mercedes, and DDC engines are not warranted or serviced by ZF. Please contact your respective dealer/distributor of those engines for warranty and servicing. 3 An extended warranty of 4/400/P will apply when a WABCO Trailer Control Line Filter is used in combination with a WABCO Trailer ABS valve.
WABCO Components1
Air Management
Air Brake Valves
1/100/P&L Air Compressors (ALL)2
Air Dryers (ALL)
Trailer Control Line Filter3
Braking Systems
ABS (Anti-Lock Braking System) Air 3/300/P&L
ABS (Anti-Lock Braking System) Hydraulic 2/200/P&L
Electronic Braking System (EBS)
3/300/P&L
Electronic Stability Control (ESC)
Trailer ABS Valve3
Roll Stability Control (RSS)
Trailer Roll Stability Support (RSS)
Driveline Suspension Control
OptiRide® Electronically Controlled Air Suspension
(ECAS) 2/200/P&L
Leveling Valves 1/100/P&L
Clutch Controls 2/200/P&L
Safety
OnGuardACTIVE®
3/300/P&L
OnLane®
OnLaneALERT®
OnSide®
Trailer SafeStart™
Trailer TailGUARD™
Telematics
TrailerCAST™ Telematics Device 3/300/P&L
Wheel End Solutions
EasyFit™ Slack Adjuster 2/200/P
MAXXUS™ Air Disc Brake 1/Unl/P&L
IVTM - Wheel Module 6/P
IVTM - All Other Products 2/P
Pan 22, 19 and 17 Air Disc Brake 1/Unl/P&L
Trailer MAXX22T™ 1/Unl/P&L
TRISTOP™ D Actuator w/ IBV 3/Unl/P
TRISTOP™ D Actuator 2/200/P
UNISTOP™ Actuator 1/100/P
• Airport Rescue Fire (ARF)
• Airport Shuttle
• Asphalt Truck
• Block Truck
• Bottom Dump Trailer
Combination
• Cementing Vehicle
• City Bus
• Commercial Pick-Up
• Concrete Pumper
• Construction Material Hauler
• Crash Fire Rescue (CFR)
• Mixer
• Demolition
• Drill Rig
• Dump
• Emergency Service
• Equipment Hauling
• Flatbed Trailer Hauler
• Flatbed Truck
• Fracturing Truck
• Front Loader
• Geophysical Exploration
• Hopper Trailer Combinations
• Landscaping Truck
• Liquid Waste Hauler
• Log Hauling
• Lowboy
• Michigan Special
Gravel Trains
• Michigan Special
Log Hauler
• Michigan Special
Steel Hauler
• Michigan Special
Waste Vehicle
• Municipal Dump
• Newspaper Delivery
• Package Delivery
• Pick-up and Delivery
• Rapid Intervention
Vehicle (RIV)
• Rear Loader
• Recycling Truck
• Residential Pick-Up/Waste
• Rigging Truck
• Roll-Off
• Scrap Truck
• Semi-End Dump
• Sewer/Septic Vacuum
• Shuttle Bus
• Side Loader
• Snowplow/Snowblower
• Steel Hauling
• Tanker
• Tank Truck
• Tractors with Pole Trailers
• Tractor/Trailer with Jeeps
• Transfer Dump
• Transfer Vehicle
• Transit Bus
• Trolley
• Utility Truck
• Winch Truck
HEAVY SERVICE VEHICLES
HEAVY SERVICE (VOCATIONAL) WARRANTY INFORMATION
HEAVY SERVICE TYPICALLY IS
• On/Off road vocations (10% or more off-road) OR
• Moderate to frequent starts/stops typically more than three (3) stops per mile
WARRANTY - MODEL YEAR 2021 VEHICLES
INDUSTRIAL AND OFF-HIGHWAY SERVICE
TYPICALLY IS
• Low mileage operation3
• Vehicles are not typically licensed for highway use
¹ ZF and WABCO branded components. 2 WABCO compressors installed on Cummins, Mercedes, and DDC engines are not warranted or serviced by ZF. Please contact your respective dealer/distributor of those engines for warranty and servicing. 3 Equivalent hours of service limit: 2,000 hours for all components.
INDUSTRIAL/OFF-HIGHWAY SERVICE WARRANTY INFORMATION
WABCO Components1
Air Management
Air Brake Valves
Air Compressors (ALL)2 2/Unl/P
Air Dryers (ALL)
Brake Actuation
Air/Hydraulic Actuators
2/Unl/P
Master Cylinders
Remote Actuators
Slave and Wheel Cylinders
Two Fluid Actuators
Brake Locks
Brake Locks (ALL)
Electric Brake Locks 2/Unl/P
Lever Locks
Braking Systems
ABS (Anti-Lock Braking System) Air 1/100/P&L
ABS (Anti-Lock Braking System) Hydraulic
Driveline Suspension Control
Clutch Controls
1/100/P&L
Leveling Valves
Electrohydraulics & Controls
Electronic Pedals
Electrohydraulic Brake Valves (EBV) 2/Unl/P
Pressure Switches
Hydraulic Braking Solutions
Accumulator Charging Valves
Hydraulic Throttle Controls and Switches 2/Unl/P
Modulating Brake Valves
Wheel End Solutions
EasyFit™ Slack Adjuster 2/200/P
Caliper Disc Brakes 2/Unl/P
MAXXUS™ Air Disc Brake 1/Unl/P&L
Multiple Disc Brakes 2/Unl/P
IVTM - Wheel Module 6/P
IVTM - All Other Products 2/P
Pan 22, 19 and 17 Air Disc Brake 1/Unl/P&L
TRISTOP™ D Actuator w/ IBV 3/Unl/P
TRISTOP™ D Actuator 2/200/P
UNISTOP™ Actuator 1/100/P
Market Common Application Types
Agriculture
Fertilizer Spreader, Tractor, Heavy Duty Ag
Trailers, Harvester, Sprayer, Skid Loader, Silage
Bagger, Slurry Wagons, Grain Cart
Airport Support
Pushback Tractor, Towing Tugs, Aircraft Tow
Tractor, Refueling Trucks, Food Service Trucks,
Baggage Tractors, De-Icing Equipment,
Runway Clearing Equipment
Construction
All-Terrain Crane, Rough Terrain Crane,
Excavator, Compactor, Wheel Loader, Road
Roller, Motor Grader, Articulated Dump Truck,
Rubber Tire Road Roller, Backhoe Loaders,
Haul Trucks, Scraper Rough Terrain Forklifts,
Trenchers, Drills
Forestry Logging Forwarder, Kidder, Loaders, Yard
Forklifts, Harvesters Fellers
Material Handling
Port Tractor, Rail Yard Spotter, Stevedoring
Tractor, Trailer Spotter, Yard Jockey, Scissor
Lift, Straddle Carrier, Manlift, Forklift, Boom Lift
Telebandlers, Aerial Work Platforms
Mining
Specialized Mining, Excavator, Haul Truck,
Underground Loader, Service Trucks, Wheel
Loaders, Scrapers, Load Haul Dumps,
Personnel Transports, Bolters, Scalers
Municipal
Street Sweeper, Utility Tractor, Utility Trucks,
Tree Trimmers, Dump Trucks, Tow Trucks, Flat
Bed Trucks, Winch Applications
Oil & Gas
Fracturing Trailer, Injecter Heads, Top Drives,
Jack/Lift Boats, Wireline Trucks, Load-On /
Load-Off
Rail
Railcar Mover, Track Layers, Grinders, Platform
Crane, Locomotive Railcars, Ballast Equipment,
Winch Applications
ABS, ELECTRONIC STABILITY CONTROL (ESC),
ROLL STABILITY CONTROL (RSC), OPTIRIDE®,
ONGUARD® AND ONLANE®, COLLECTIVELY
“ELECTRONICS”
Failure of electronic components due to overvoltage
condition, improper grounding, electrostatic discharge
(ESD), improper shielding, electromagnetic interference (EMI), or other wiring or installation issues. Malfunctions and failure codes caused by other electronic subsystem failures (data bus, engine, transmission, dashboard, etc.)
HYDRAULIC COMPONENTS
For certain components, brake fluid DOT3 or DOT4 is
used as the operating medium. Use of any other fluid will void all warranties associated with that component. For hydraulic braking applications the brake fluid is considered a maintenance item. Maintenance intervals are listed in TB1367.
COVERAGE LIMITATIONS
PRODUCT DESCRIPTION
ALL PRODUCTS
Any claim beyond 60 days from date of repair will not be accepted or honored under this warranty program.
Products purchased on an incomplete vehicle (glider) are limited to one year, 1/Unl/P.
For vehicles that operate full- or part-time outside of the United States and Canada, a 1-Year/Unlimited Miles parts only (1/Unl/P) will apply.
TOOLBOX PLUS™ DIAGNOSTIC SOFTWARE
Proper diagnostics of WABCO Electronics may require the latest version of TOOLBOX PLUS™. Additional labor due
to use of an outdated version of TOOLBOX™ software
and/or the time to purchase or install the latest version of TOOLBOX PLUS™ are not covered under product
warranty.
TERMS AND CONDITIONS
COVERAGE EXCLUSIONS
PRODUCT DESCRIPTION
ALL PRODUCTS
This Warranty shall not apply to the following, but not limited to: (1) damage to the product or its component
parts caused by incorrect use, installation, maintenance or repair, including without limitation (a) improper fit of mating components or brackets, damaged threads, cut, broken,
chafed, pinched or otherwise damaged wiring (sensors,
harnesses and connectors), (b) sensors damaged during
removal when seized in block, or associated with sensor adjustments/ alignments, and (c) damage resulting from the use or installation of non-genuine WABCO components or
materials; (2) damage to the product, its component parts, or diminished product or component part performance due to incorrect operation, deviation from approved conditions or misapplication; (3) any unauthorized disassembly of the product or its component parts including without limitation (a) obliterated, defaced or missing WABCO or WABCO
name plate, serial numbers or label identifying the device as a ZF product or WABCO component, (b) changes to sealed
adjusting screws, and (c) opening or attempted repair of non-serviceable components; (4) malfunction
of the component due to internal contamination of the
vehicle system including without limitation (a) water and other contamination damage that is due to the use of a
non-genuine air dryer cartridge or (b) valve failures due to contamination in air system, (5) complaints associated
with noise, (6) damage resulting from corrosion (including oxidation of electrical devices and connections).
AIR DRYERS
Mounting brackets (see vehicle OEM). Desiccant cartridge housing only.
AIR SYSTEM COMPONENTS
Normal wear items; Gladhand seals, dash valve knobs,
valve actuation handles, treadles, pedals.
WARRANTY - MODEL YEAR 2021 VEHICLES
(1) What is Covered by this Commercial Warranty?
ZF CV Systems North America LLC and its North American
subsidiaries and affiliates (ZF) warrant to the owner (“Owner”) that the components listed in this publication, which have been installed by an Original Equipment Manufacturer (“OEM”) as original equipment will be free from defects in material and workmanship. This warranty coverage begins from the original in-service date to the limits provided and runs concurrently with any warranties provided by OEMs and/or any distribution agreements and/or any service contracts that cover the components listed in this publication, if any. If the components listed in this publication are covered by an OEM warranty and/or service contract, then the OEM’s warranty and/ or service contract shall supersede ZF’s warranty and Owner shall comply with all OEM’s warranty and/or service contract requirements for claims under such OEM’s warranty and/or service contract until those agreements expire.
Once those agreements expire and provided the ZF warranty has not expired under the terms stated above, the ZF warranty will be in effect until its expiration date.
Warranty coverage ends at the expiration of the applicable time period from the date of vehicle purchase by the first Owner, or, the applicable mileage limitation, whichever occurs first. Duration of coverage varies by component and vocation as detailed previously in this publication.
Some components are warranted for parts only and the Owner must pay any labor costs associated with the repair or replacement of the component. Other components are warranted for both parts and reasonable labor to repair or replace the subject component.
Additional diagnostic time due to use of an outdated version of TOOLBOX™, time to purchase or install latest version of TOOLBOX™ are the responsibility of the authorized ZF distributor networks and are not covered under product warranty. Components installed as replacements under this warranty are warranted only for the remainder of the original period of time or mileage under the original warranty. (2) Designation of Vocational Use Required. To obtain warranty coverage, each Owner must notify ZF through the OEM new truck and/or trailer dealer of the intended vocational use of the vehicle into which the WABCO components have been incorporated prior to the vehicle inservice date. This notification may be accomplished by registering the vehicle through your OEM new truck and/or trailer dealer or with ZF directly. Failure to notify ZF of (I) the intended vocational use of the vehicle or (II) a change in vocational use from that which was originally designated, will result in the application of a one year, unlimited mileage, parts only warranty (1/Unl/P) from the initial inservice date. A second Owner and each subsequent Owner must also notify ZF as to the intended vocational use of the vehicle. This notification can be sent directly to ZF or through
the OEM new truck and/or trailer dealer. The duration and mileage coverage of this warranty cannot exceed the coverage extended to the first Owner after his or her initial designation of vocational use. Coverage under ZF’s warranty requires that the application of products be properly approved pursuant to OEM and ZF, approvals. (3) What is the Cost of this Warranty? There is no charge to the Owner for this warranty.
(4) What is not Covered by this Warranty? In addition to the items listed on "Coverage Exclusions," this warranty does not cover normal wear and tear, or service items; nor does it cover a component that fails, malfunctions or is damaged as a result of (a) improper handling, storage, installation, adjustment, repair or modification including the use of unauthorized attachments or changes or modification in the vehicle’s configuration, usage, or vocation from that which was originally approved by ZF, (b) accident, fire or other casualty, natural disaster, road debris, negligence, misuse, abuse, or improper use (including loading beyond the specified maximum vehicle weight or altering engine power settings to exceed the brake system capacity), or (c) improper or insufficient maintenance (including deviation from maintenance intervals, approved lubricants, or lube levels). This warranty does not cover any component or part that is not sold by ZF. (5) To obtain service. If the owner discovers within the applicable coverage period a defect in material or workmanship, the Owner must promptly give notice to either ZF or the dealer from which the vehicle was purchased. To obtain service, the vehicle must be taken to any participating OEM dealer or ZF distributor networks' servicer. The dealer or ZF authorized servicer will inspect the vehicle and contact ZF for an evaluation of the claim. When authorized by ZF, the dealer or ZF authorized servicer will repair or replace during the term of this warranty any defective WABCO component covered by this warranty. (6) Disclaimer of Warranty and Limitation of remedies. TO THE MAXIMUM
EXTENT PERMITTED BY LAW, THE LIMITED WARRANTY SET
FORTH HEREIN IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, ARISING BY OPERATION OF
LAW OR OTHERWISE, INCLUDING, WITHOUT LIMITATION, ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE AND/OR WARRANTY FOR HIDDEN OR
LATENT DEFECTS, AND IN NO EVENT WILL ZF OR ANY OF ITS
AFFILIATES BE LIABLE FOR DIRECT, INDIRECT, INCIDENTAL,
PROGRESSIVE, SPECIAL, OR CONSEQUENTIAL DAMAGES OF ANY
KIND.
TERMS AND CONDITIONS
(7) Legal action. Any legal action or claim arising from or related to this Warranty, in contract or otherwise, must be commenced within one year from the accrual of that cause of action, or be barred forever. Any dispute arising in connection with this agreement shall be governed by and construed according to the laws of the State of Michigan and be brought, heard and determined exclusively in either the Circuit Court for the County of Oakland, State of Michigan or the United States District Court for the Eastern District of Michigan. The parties stipulate that the referenced venues are convenient.
(8) Remedy. The exclusive remedy under this warranty shall be the repair or replacement of the defective component at ZF's option. ZF reserves the right to require that all applicable covered components are available and/or returned to ZF for review
and evaluation. THE MAXIMUM LIABILITY, IF ANY, OF ZF FOR ALL
DAMAGES, INCLUDING WITHOUT LIMITATION CONTRACT
DAMAGES, BREACH OF WARRANTY, NEGLIGENCE, STRICT
LIABILITY, OR OTHER TORT, IS LIMITED TO AN AMOUNT NOT TO EXCEED THE PURCHASE PRICE OF THE PRODUCT and where
indicated in the product and application warranty information above, the inclusion of labor is limited to the standard repair time. THE
PARTIES ACKNOWLEDGE AND AGREE THAT THE LIMITATION
OF DAMAGES PROVISION SET FORTH IN THIS PARAGRAPH
SURVIVES BETWEEN THE ORIGINAL END USER AND ZF EVEN IF
THE EXCLUSIVE REMEDY SET FORTH ABOVE IS DEEMED TO FAIL
OF ITS ESSENTIAL PURPOSE. ZF may change the design or make improvements to its Products without incurring any warranty obligation for previously manufactured Product .
(9) Entire Agreement. This is the entire agreement between ZF and the Owner about warranty and no, ZF employee, or dealer is authorized to make any additional warranty on behalf of ZF unless in writing and signed by an authorized representative of ZF.
About ZF Friedrichshafen AG
ZF is a global technology company and supplies systems for passenger cars, commercial vehicles and industrial technology, enabling the next generation of mobility. ZF allows vehicles to see, think and act. In the four technology domains Vehicle Motion Control, Integrated Safety, Automated Driving, and Electric Mobility, ZF offers comprehensive solutions for established vehicle manufacturers and newly emerging transport and mobility service providers. ZF electrifies different kinds of vehicles. With its products, the company contributes to reducing emissions and protecting the climate.
ZF, which acquired WABCO Holdings Inc. on May 29, 2020, now has 160,000 employees worldwide with approximately 260 locations in 41 countries. In 2019, the two then-independent companies achieved sales of €36.5 billion (ZF) and $3.4 billion (WABCO). For more information, visit: www.wabco-na.com
© 2021 ZF CV Systems North America LLC - All rights reserved - SP1375 / 2.2021 For further product details contact your distributor or the WABCO Customer Care Center at 855-228-3203.
Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 2/8/2010 WA0012
1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL
OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,
INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.
2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.
This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.
THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE
TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.
This warranty applies only to the cab tubular support and mounting structures and other structural components of the cab of the vehicle model, as identified in the Pierce
specifications for the Fire and Rescue Apparatus.
This warranty does not apply to damage caused by corrosion.
Conditions and
Exclusions:
See Also
Paragraphs
2 thru 4
Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:
Fire and Rescue Apparatus
Coverage:
Ten (10) Year Structural Integrity
Custom Cab
Ten (10) Years
- or -
100,000 Miles
Warranty Period
Ends After:
The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:
The Pierce Custom Cab shall be free from structural failures caused by defects in material and workmanship
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;
4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.
Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,
INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,
WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW
OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY
PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS
THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,
REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.
If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.
Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.
3. BUYER'S EXCLUSIVE REMEDY.
4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.
Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,
INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,
WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW
OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY
PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS
THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,
REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.
If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.
Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.
3. BUYER'S EXCLUSIVE REMEDY.
Fire and Rescue Apparatus
Coverage:
Ten (10) Year Pro-Rated Paint and Corrosion
Cab
Ten (10) Years Warranty Period
Ends After:
The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:
Exterior surfaces of the cab painted by Pierce shall be free from blistering, peeling, corrosion or any other adhesion defect caused by defective manufacturing methods or paint material selection.
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:
Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 2/8/2010 WA0055
1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL
OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,
INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.
2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.
This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.
THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE
TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.
This limited warranty is applicable to the vehicle in the following percentage costs of warranty repair, if any:
Topcoat Durability & Appearance: Gloss, Color Retention & Cracking
0-72 months 100%
73-96 months 50%
97-120 months 25%
Integrity of Coating System: Adhesion, Blistering/Bubbling 0-36 months 100%
37-84 months 50%
85-120 months 25%
Corrosion: Dissimilar Metal and Crevice
0-36 months 100%
37-48 months 50%
49-72 months 25%
73-120 months 10%
Corrosion Perforation
0-120 months 100%
This limited warranty applies only to exterior paint. Paint on the vehicle's interior is warranted only under the Pierce Basic One Year Limited Warranty.
Items not covered by this warranty include:
(a) Damage from lack of maintenance and cleaning (proper cleaning and maintenance procedures are detailed in the Pierce operation and maintenance manual).
(b) UV paint fade.
(c) Any cab not manufactured by Pierce.
Conditions and
Exclusions:
See Also
Paragraphs
2 thru 4
Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 2/8/2010 WA0014
1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL
OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,
INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.
2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.
This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.
THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE
TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.
This limited warranty applies to all of the control modules for the Command Zone system, including the full color graphic displays. Related wire harnesses, cables and connectors are not covered under this limited warranty and are instead covered under the Pierce One Year Basic Apparatus Limited Warranty.
Conditions and
Exclusions:
See Also
Paragraphs
2 thru 4
Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:
Fire and Rescue Apparatus
Coverage:
Five (5) Year Material and Workmanship
Command Zone Electronics
Five (5) Years Warranty Period
Ends After:
The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:
Command Zone control modules shall be free from failures caused by defects in material and workmanship
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;
4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.
Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,
INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,
WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW
OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY
PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS
THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,
REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.
If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.
Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.
3. BUYER'S EXCLUSIVE REMEDY.
Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 1/11/2011 WA0188
1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL
OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,
INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.
2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.
This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.
THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE
TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.
This limited warranty does not apply to related wire
harnesses, cables, and connectors, which are covered by the Pierce one (1) year basic apparatus limited warranty.
Conditions and
Exclusions:
See Also
Paragraphs
2 thru 4
Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:
Fire and Rescue Apparatus
Coverage:
54 Months Material and Workmanship
Camera System
Fifty - Four (54) months Warranty Period
Ends After:
Warranty Begins: The date of delivery.
This limited warranty covers repairs to correct any defect related to materials or workmanship of the Sharpvision
camera system installed on the apparatus occuring during the warranty period.
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;
4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.
Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,
INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,
WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW
OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY
PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS
THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,
REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.
If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.
Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.
3. BUYER'S EXCLUSIVE REMEDY.
Fire and Rescue Apparatus
Coverage:
Ten (10) Year Material and Workmanship
Pierce 12V LED Strip Light
Limited Warranty
Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:
This limited warranty covers repairs to correct any defect related to materials or workmanship of the Pierce 12V LED strip lights installed on the apparatus occuring during the warranty period.
1. LIMITED WARRANTY
(b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:
This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.
THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE
TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.
This limited warranty does not apply to related wire
harnesses, cables, and connectors, which are covered by the Pierce one (1) year basic apparatus limited warranty.
Conditions and
Exclusions:
See Also
Paragraphs
2 thru 4
4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.
Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,
INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,
WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW
OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY
PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS
THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,
REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.
If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.
Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.
3. BUYER'S EXCLUSIVE REMEDY.
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce.
Ten (10) Year Warranty Period
Ends After:
Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 7/5/2011 WA0203
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL
OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,
INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.
2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.
NEW PRODUCT WARRANTY
PARTICIPATING OEM SALES
DISTRIBUTOR SALES
LIMITED WARRANTY ON NEW ALLISON AUTOMATIC TRANSMISSIONS
USED IN EMERGENCY VEHICLE APPLICATIONS
Allison Transmission will provide for repairs or replacement, at its option, during the warranty period of each new Allison transmission listed below that is installed in an Emergency Vehicle in accordance with the following terms, conditions, and limitations.
WHAT IS COVERED
WARRANTY APPLIES — This warranty is for new Allison transmission models listed below installed in an Emergency Vehicle and is provided to the original and any subsequent owner(s) of the vehicle during the warranty period. REPAIRS COVERED — The warranty covers repairs or replacement, at Allison Transmission’s option, to correct any transmission malfunction resulting from defects in material or workmanship occurring during the warranty period. Needed repairs or replacements will be performed using the method Allison Transmission determines most appropriate under the circumstances. TOWING — Towing is covered to the nearest Allison Transmission Distributor or authorized Dealer only when necessary to prevent further damage to your transmission.
PAYMENT TERMS — Warranty repairs, including parts and labor, will be covered per the schedule shown in the chart contained in section “APPLICABLE MODELS, WARRANTY LIMITATIONS, AND ADJUSTMENT SCHEDULE.” OBTAINING REPAIRS — To obtain warranty repairs, take the vehicle to any Allison Transmission Distributor or authorized Dealer within a reasonable amount of time and request the needed repairs. A reasonable amount of time must be allowed for the Distributor or Dealer to perform necessary repairs.
TRANSMISSION REMOVAL AND REINSTALLATION — Labor costs for the removal and re-installation of the transmission, when necessary to make a warranty repair, are covered by this warranty. WARRANTY PERIOD — The warranty period for all coverages shall begin on the date the transmission is delivered to the first retail purchaser, with the following exception:
Demonstration Service - A transmission in a new truck or bus may be demonstrated to a total of 5000 miles (8000 kilometers).
If the vehicle is within this limit when sold to a retail purchaser, the warranty start date is the date of purchase. Normal warranty services are applicable to the demonstrating Dealer. Should the truck or bus be sold to a retail purchaser after these limits are reached, the warranty period will begin on the date the vehicle was first placed in demonstration service and the purchaser will be entitled to the remaining warranty.
APPLICABLE MODELS, WARRANTY LIMITATIONS, AND ADJUSTMENT SCHEDULE
WARRANTY LIMITATIONS
(Whichever occurs first)
ADJUSTMENT CHARGE TO BE
APPLICABLE PAID BY THE CUSTOMER
MODELS
Months
Transmission Miles
Or Kilometers Parts Labor
MT, MD
3000, 3200, 3500, 3700 0–24 No Limit No Charge No Charge HT with Hydraulic Controls 0–24 No Limit No Charge No Charge AT, 1000 Series, 2000 Series,
2400 Series 0–36 No Limit No Charge No Charge
HT with Electronic Controls 0–60 No Limit No Charge No Charge HD
1000 EVS, 2100 EVS, 2200 EVS
2350 EVS, 2500 EVS, 2550 EVS,
3000 EVS, 3500 EVS, 4000,
4000 EVS, 4500, 4500 EVS, 4700,
4700 EVS, 4800, 4800 EVS
0–60 No Limit No Charge No Charge
WHAT IS NOT COVERED
DAMAGE DUE TO ACCIDENT, MISUSE, or ALTERATION — Defects and damage caused as the result of any of the following are not covered:
— Flood, collision, fire, theft, freezing, vandalism, riot, explosion, or objects striking the vehicle; — Misuse of the vehicle;
— Installation into unapproved applications and installations; — Alterations or modification of the transmission or the vehicle, and — Damage resulting from improper storage (refer to long-term storage procedure outlined in the applicable Allison Service Manual) — Anything other than defects in Allison Transmission material or workmanship NOTE: This warranty is void on transmissions used in vehicles currently or previously titled as salvaged, scrapped, junked, or totaled. CHASSIS, BODY, and COMPONENTS — The chassis and body company (assemblers) and other component and equipment manufacturers are solely responsible for warranties on the chassis, body, component(s), and equipment they provide. Any transmission repair caused by an alteration(s) made to the Allison transmission or the vehicle which allows the transmission to be installed or operated outside of the limits defined in the appropriate Allison Installation Guideline is solely the responsibility of the entity making the alteration(s). DAMAGE CAUSED by LACK of MAINTENANCE or by the USE of TRANSMISSION FLUIDS NOT RECOMMENDED in the OPERATOR’S MANUAL — Defects and damage caused by any of the following are not covered:
— Failure to follow the recommendations of the maintenance schedule intervals applicable to the transmission; — Failure to use transmission fluids or maintain transmission fluid levels recommended in the Operator’s Manual. MAINTENANCE — Normal maintenance (such as replacement of filters, screens, and transmission fluid) is not covered and is the owner’s responsibility.
REPAIRS by UNAUTHORIZED DEALERS — Defects and damage caused by a service outlet that is not an authorized Allison Transmission Distributor or Dealer are not covered.
USE of OTHER THAN GENUINE ALLISON TRANSMISSION PARTS — Defects and damage caused by the use of parts that are not genuine Allison Transmission parts are not covered. EXTRA EXPENSES — Economic loss and extra expenses are not covered. Examples include but are not limited to: loss of vehicle use; inconvenience; storage; payment for loss of time or pay; vehicle rental expense; lodging; meals; or other travel costs. “DENIED PARTY” OWNERSHIP — Warranty repair parts and labor costs are not reimbursed to any participating or non-participating OEMs, dealers or distributors who perform warranty work for, or on behalf of, end users identified by the United States as being a “denied party” or who are citizens of sanctioned or embargoed countries as defined by the U.S. Department of Treasury Office of Foreign Assets Control. Furthermore, warranty reimbursements are not guaranteed if the reimbursement would be contrary to any United States export control laws or regulations as defined by the U.S. Department of Commerce, the U.S. Department of State, or the U.S. Department of Treasury.
OTHER TERMS APPLICABLE TO CONSUMERS AS DEFINED by the MAGNUSON-MOSS WARRANTY ACT This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
Allison Transmission does not authorize any person to create for it any other obligation or liability in connection with these transmissions.
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE APPLICABLE TO THESE TRANSMISSIONS IS LIMITED IN DURATION TO THE DURATION OF THIS WRITTEN WARRANTY.
PERFORMANCE OF REPAIRS AND NEEDED ADJUSTMENTS IS THE EXCLUSIVE REMEDY UNDER THIS WRITTEN WARRANTY OR ANY IMPLIED WARRANTY. ALLISON TRANSMISSION SHALL NOT BE LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES (SUCH AS, BUT NOT LIMITED TO, LOST WAGES OR VEHICLE RENTAL EXPENSES) RESULTING FROM BREACH OF THIS WRITTEN WARRANTY OR ANY IMPLIED WARRANTY.** ** Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you.
OTHER TERMS APPLICABLE TO OTHER END-USERS
THIS WARRANTY IS THE ONLY WARRANTY APPLICABLE TO THE ALLISON TRANSMISSION MODELS LISTED
ABOVE AND IS EXPRESSLY IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. ALLISON
TRANSMISSION DOES NOT AUTHORIZE ANY PERSON TO CREATE FOR IT ANY OTHER OBLIGATION OR LIABILITY IN CONNECTION WITH SUCH TRANSMISSIONS. ALLISON TRANSMISSION SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM BREACH OF THIS WARRANTY OR ANY IMPLIED WARRANTY.
QUESTIONS
If you have any questions regarding this warranty or the performance of warranty obligations, you may contact any Allison Transmission Distributor or Dealer or write to:
Allison Transmission, Inc.
P.O. Box 894
Indianapolis, IN 46206-0894
Attention: Warranty Administration PF-9
Form SE0616EN (201009)
Warranty Begins:
The transmission cooler shall be free from component or structural failures caused by defects in material and/or workmanship. Collateral damage up to $10,000 per
occurrence is available for the first three (3) years.
(b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; (d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce.
Five (5) Years on Oil Cooler and three (3) years on collateral damage coverage
Warranty Period
Ends After:
Fire and Rescue Apparatus
Coverage:
Five (5) Year Material and Workmanship - Transmission Oil Cooler Three (3) Year Collateral Damage Coverage
1. LIMITED WARRANTY
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:
The date of delivery to the first retail purchaser.
This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.
THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE
TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.
This warranty does not cover repair due to accidents,
misuse, and excessive vibration, flying debris, storage damage (freezing), negligence or modification. This warranty is void if any modification or repairs are performed without authorization. This also voids any future warranty.
This warranty does not cover cost of maintenance or repairs due to lack of required maintenance services as
recommended. Performance of the required maintenance
and use of proper fluids are the responsibility of the owner.
Towing is covered to the nearest distributor or authorized dealer only when necessary to prevent further damage to your transmission.
Labor costs for the removal and reinstallation of goods may be covered when necessary to make repairs. Please contact your OEM for authorization.
Replacement of cooler during the warranty period is limited to 100% of reasonable labor costs up to a maximum of $700 to remove, replace, or repair the oil cooler.
Conditions and
Exclusions:
See Also
Paragraphs
2 thru 4
4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.
Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,
INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,
WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW
OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY
PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS
THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,
REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE
POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.
If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.
Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.
3. BUYER'S EXCLUSIVE REMEDY.
Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 2/22/2012 WA0216
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES
ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,
INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.
2. DISCLAIMERS OF WARRANTIES
capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.
Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 2/8/2010 WA0009
1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL
OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,
INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.
2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.
This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.
THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE
TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.
This warranty applies only to the body tubular support and mounting structures and other structural components of the body of the vehicle model, as identified in the Pierce
specifications for the Fire and Rescue Apparatus.
This warranty does not apply to damage caused by corrosion.
Conditions and
Exclusions:
See Also
Paragraphs
2 thru 4
Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:
Fire and Rescue Apparatus
Coverage:
Ten (10) Year Structural Integrity
Apparatus Body
Ten (10) Years
- or -
100,000 Miles
Warranty Period
Ends After:
The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:
The apparatus body shall be free from structural failures caused by defects in material and workmanship
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;
4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.
Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,
INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,
WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW
OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY
PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS
THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,
REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.
If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.
Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.
3. BUYER'S EXCLUSIVE REMEDY.
Effective March 15, 2010
AMDOR Inc. TERMS OF BUSINESS AND GENERAL INFORMATION
Warranty:
All AMDOR Inc. roll-up door products are warranted for a period of 10 years from the date of delivery (with the exception of wet paint adhesion - please see below). AMDOR Inc. liability covers the replacement or repair of any component that fails due to defects in material and / or workmanship during the coverage period. We accept no liability for claims made for damages to any part (or parts) of a vehicle and / or machine (of any type) or injury claims by a person or persons assumed or alleged to have been brought about by the use or misuse of any product supplied by AMDOR Inc. Warranty coverage does not extend to door attachments including (but not limited to) decals, emblems, stripes and adhesives.
In order to initiate the claims process please contact your authorized representative of AMDOR Inc. Warranty claims must be accompanied by a written description providing full and reasonable details as to the nature of the defect. Upon receipt of your claim arrangements will be made to inspect the defective product (if necessary). Justified warranty claims will be repaired, exchanged, or credited to the customer's account at AMDOR Inc.'s discretion. All warranty claims must be approved in writing by the Customer Service Manager for AMDOR Inc. There are no exceptions to this clause.
Limited warranty coverage includes the labor associated with the disassembly and assembly of products deemed to be defective by AMDOR Inc. Labor allowances are based on a set time schedule as determined by AMDOR Inc. The maximum allowable hourly labor rate is $ 50. All warranty labor claims must be approved in writing by an authorized representative of AMDOR Inc. prior to commencement of work. Allowances for removal and installation:
Curtain replacement: 3/4 hour
Balancer replacement: 1 hour
Door ajar switch 3/4 hour
Bottom Panel Assembly: 1/2 hour
Slat replacement: 3/4 hour
Door removal and replacement 1 1/2 hours
Items authorized for return must be accompanied by a Return Goods Authorization (RGA) number. We will accept collect shipments of items deemed to be defective provided that they are returned via the most economical carrier. Should items be returned by means other than the most economical carrier the difference will be charged back to the sender.
AMDOR Inc. reserves the right to reject any claim when a product has been opened, interfered with or modified. Claims may also be rejected when damage to the product (or any sub-assembly) has been brought about by accident, misuse, abuse, vandalism, incorrect installation, temperature extremes, chemical exposure or any factor other than regular operating conditions.
Limited Wet Paint Match Adhesion Warranty
AMDOR Inc. warrants wet paint finishes applied by AMDOR utilizing our approved factory paint specification. All wet paint match colors must be approved in writing by an authorized OEM representative. AMDOR Inc. will provide a color spray out for this purpose. The time required for shipping and consideration of initial color spray outs will be considered over and above stated lead times. Warranty coverage will extend for a period of not less than 5 years from the date of delivery as determined by AMDOR Inc.'s Packing Slip. AMDOR reserves the right to determine whether individual units will be replaced and / or repaired by an AMDOR approved vendor. An allowance will be made for labor associated with the disassembly and assembly of individual units at the prescribed hourly rate of $ 50 per hour. Compensation for labor will not exceed the maximum time allowance permitted for door removal and replacement. Written approval including specified allowance for time must be obtained from AMDOR prior to initiating work. Warranty coverage will extend to the following visible paint system defects:
1./ Loss of mechanical adhesion as evidenced by peeling, cracking or blistering which exposes the substrate material.
2./ Corrosion of the substrate due to paint system failure.
3./ Fading which results in a substantial departure from the primary AMDOR approved body color.
Wet paint adhesion limited warranty coverage will be excluded when damages to the system are determined by AMDOR Inc. to be a result of the following:
1./ Damage caused through the use of attachments including (but not limited to) decals, labels, adhesives, non factory approved coatings.
2./ Loss of gloss, discoloration or damage due to improper maintenance (including but not limited to) mechanical wash systems, pressure washers, steam cleaners, non approved wash or polishing agents.
3./ Abuse, acts of nature, excessive heat / cold, chemical exposure, vandalism and / or accidents.
4./ Scratches, chips, abrasions, or dents from any source.
This document supercedes all previous written and / or verbal warranties provided by AMDOR Inc. and / or it's affiliates.
Fire and Rescue Apparatus
Coverage:
Twenty (20) Year Structural Integrity
Pierce Aerial Device
Limited Warranty
Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:
Each new Pierce Aerial Device shall be free from defects in material and workmanship.
Aerial Device Models Covered by this warranty include:
Aerial Platforms
Aerial Ladders
SkyBoom
1. LIMITED WARRANTY
(b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot; Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:
This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.
THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE
TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.
This warranty applies only to the torque box, turntable, aerial sections and other structural components of the aerial
device, as identified in the Pierce specifications for the aerial device. This warranty shall be void if, or to the extent that the aerial device is not maintained in strict compliance with NFPA Standard 1911 in effect at time of sale, including such periodic inspections and testing by qualified third parties as are required by that Standard as it may be in effect from time to time. Proof of such compliance shall accompany any
claims under this warranty. Third party testing agencies known to Pierce to be qualified for such purposes may be obtained from the Pierce Customer Service Department
This warranty does not apply to damage caused by
corrosion.
Conditions and
Exclusions:
See Also
Paragraphs
2 thru 4
4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.
Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,
INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,
WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW
OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY
PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS
THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,
REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE
POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.
If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.
Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.
3. BUYER'S EXCLUSIVE REMEDY.
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce.
Twenty (20) Years
- or -
100,000 Miles
Warranty Period
Ends After:
Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 10/23/2013 WA0052
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES
ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,
INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.
2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty. {00046826;v2}
AMITY FIRE AND SAFETY, INC.
3750 CHESTNUT ROAD
ALBURTIS, PA 18011-0451
Phone: 610-966-3115
Fax: 610-965-6313
* STANDARD FIVE YEAR WARRANTY *
(standard warranty is in effect for parts shipped after 4/15/10) Three Function Swivel
A. PRESHIPMENT TESTING The Three Function Swivel fabricated by Amity which is exposed to pressure during normal use is subject to final inspection using the following pressure minimums:
1. Hydrostatic applications will be tested to 400 PSI unless specified otherwise on approved drawings. Operating pressures on installed systems are not to exceed 250 PSI at any point in the system. Warranty will be voided and Amity will not be held liable for failure and/or damage occurring from Water Hammering or freezing of water in any system.
2. Hydraulic applications will be tested to 4000 PSI. System operating pressure in application to be 3000 PSI maximum.
3. Dielectric and Continuity Test all circuits. 30 Amp max current loading.
B. THREE FUNCTION SWIVEL MAINTENANCE – Our Three Function Swivel has been fully tested at assembly. Under no circumstances is there to be any maintenance performed internally or externally to the Three Function Swivel by Purchaser or any other third party other than an authorized representative of or Amity itself. The Three Function Swivel is sealed and must remain so. The Three Function Swivel is designed for a long maintenance free life. Should any problems occur or replacement be necessary, first contact Amity. There is to be no field maintenance performed on the Three Function Swivel .
C. MOUNTING REQUIREMENTS – The following are the mounting requirements for the Three Function Swivel:
1. Mounting points and methods are to be determined at the initial design stage. All drawings and applicable documentation must be signed off by both parties and filed for future reference. No deviation to the approved mounting is allowed without approval from Amity.
2. The Three Function Swivel is to be mounted concentric to the center of the turntable bearing.
3. All inlet and outlet plumbing to conform to swivel mounting, under no circumstances is the Three Function Swivel to be positioned to match connections. This will avoid putting excessive loads on the Three Function Swivel. All tubing or piping to be supported by means other than the Three Function Swivel.
D. LIMITED WARRANTY, LIMITATIONS, CONDITIONS AND PROCEDURES REQUIRED.
1. The Three Function Swivel is warranted to be free of defects in labor and/or materials for a period of five (5) years from the Date of Service. For purposes here, “Date of Service” shall mean the date when the Three Function Swivel, or the unit to which the Three Function Swivel is incorporated, passes final Underwriters Laboratory testing, or similarly compliant testing, and is certified for service. Evidence of such Date of Service shall be required in connection with any warranty claim by Purchaser.
2. The Three Function Swivel shall be repaired or replaced at the sole option and expense of the Amity provided the Three Function Swivel alleged to be defective was used for its intended normal use of operation and subject to the following qualifications and limitations.
3. Any alteration of the Three Function Swivel without consent from Amity is strictly forbidden and shall void warranty.
4. No welding shall be performed on finished Three Function Swivel.
5. No responsibility is assumed for any malfunctions or damages which are occasionally caused by foreign objects which may be ingested into water or hydraulic systems such as, but not limited to stones, sand or metal chips.
6. Amity assumes responsibility for our Three Function Swivel, which is defective only, and therefore, it will not assume responsibility for labor to either remove or install our Three Function Swivel unless it agrees in writing to assume such responsibility.
7. Unless otherwise approved in writing by the Amity all returns of defective Three Function Swivels (or allegedly defective Three Function Swivels) are at Purchaser’s expense and must include a RGA number issued by the Amity. {00046826;v2}
8. All warranty claims must be presented at the time the problem occurs, or as soon as practical thereafter, either called or faxed to the Amity and include the numbers on the assembly’s Amity’s label with a detailed explanation of the difficulty in order for the matter to be appropriately evaluated and resolved.
9. Amity will not be held liable for damage incurred during shipment.
10. No responsibility shall be assumed for misuse or improper mounting, unreasonably use or abuse of the Three Function Swivel and or failure to provide or use improper maintenance, failure to follow written installation and use in instruction or any use other than the customary designed use.
THE REMEDIES PROVIDED IN THE ABOVE EXPRESS LIMITED WARRANTY AND ARE THE SOLE AND EXCLUSIVE REMEDIES AVAILABLE. NO OTHER EXPRESS WARRANTIES ARE MADE. ALL IMPLIED
WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR USE ARE LIMITED IN DURATION AS SET FORTH ABOVE. IN NO EVENT SHALL THE AMITY ASSUME OR BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES.
THE WITHIN DESCRIBED WARRANTY SHALL ONLY BE AFFORDED TO THE ORIGINAL PURCHASER OR FOR
INCORPORATION INTO ANOTHER UNIT AND TO FIRST PURCHASER AS PART OF COMPLETED UNIT,
HOWEVER, THE WARRANTY PERIOD OF FIVE YEARS IS FROM THE DATE OF SERVICE WITH THE UNDERSTANDING IT IS INSTALLED WITHIN A REASONABLE TIME PERIOD.
Dated: _______________ ____, 20__
Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 6/28/2011 WA0200
1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES
ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,
INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.
2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.
This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.
THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE
TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.
Pierce's obligation under this warranty is limited to repairing or replacing without charge, as Pierce may elect, the
hydraulic lines, fittings, valves, seals, cylinders, filters, pumps, hydraulic motors, rotary actuators, or components which Pierce determines to have failed due to defective material and workmanship.
This warranty shall not apply unless the aerial device is inspected in accordance with NFPA 1911 Standard for
Inspection, Maintenance, Testing, and Retirement of InService Automotive Fire Apparatus and the applicable Pierce Operator and Maintenance Manuals.
Conditions and
Exclusions:
See Also
Paragraphs
2 thru 4
Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:
Fire and Rescue Apparatus
Coverage:
Five (5) Year Material and Workmanship Aerial Hydraulic System Components
Three (3) Year Material and Workmanship Aerial Hydraulic System Seals
Five (5) Years and Three (3) Years Warranty Period
Ends After:
The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:
The aerial hydraulic system components and seals shall be free from component or structural failures caused by defects in material and/or workmanship.
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;
4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.
Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,
INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,
WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW
OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY
PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS
THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,
REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE
POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.
If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.
Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.
3. BUYER'S EXCLUSIVE REMEDY.
{00046826;v2}
AMITY FIRE AND SAFETY, INC.
3750 CHESTNUT ROAD
ALBURTIS, PA 18011-0451
Phone: 610-966-3115
Fax: 610-965-6313
* STANDARD TEN YEAR WARRANTY *
(standard warranty is in effect for parts shipped after 4/15/10) Telescopic Waterways
A. PRESHIPMENT TESTING All waterways fabricated by Amity are final inspected using the following pressure minimums:
1. Hydrostatic applications will be tested to 400 PSI unless specified otherwise on approved drawings. Operating pressures on installed systems are not to exceed 250 PSI at any point in the system. Warranty will be voided and Amity will not be held liable for failure and/or damage occurring from Water Hammering or freezing of water in any system.
B. COMPONENTS DESCRIPTION AND MAINTENANCE
1. All components are thoroughly greased at assembly. Since internally lubricated seals are used, regular greasing is not required. We recommend components not be greased at installation.
2. Slip Tube Assemblies may be greased at the Amity’s regularly scheduled Aerial Inspections. The seals in the Slip Tube Assemblies are self-lubricating, so greasing is not mandatory. We do recommend a visual inspection of the Slip Tube Assembly while it is fully extended after initial installation, from that point on we recommend inspection every ten hours of aerial operation. If any deposits of aluminum appear, they are to be rubbed off using a Teflon scouring pad.
Slip Tube Assemblies are designed to give long maintenance free service; however, like any product, problems may occur and periodic visual inspections will aid in determining if a potential problem exists and warrants a call to us.
Care must be taken to keep debris off of extended tubes. We recommend wiping tubes with light oil (10 weight) or hydraulic oil after use, if tubes appear to have contamination on them. Under no circumstance are tubes to be cleaned with lacquer thinner, or any other solvent.
C. LIMITED WARRANTY, LIMITATIONS, CONDITIONS AND PROCEDURES REQUIRED.
1. Products are warranted to be free of defects in labor and/or materials for a period of ten years from the date of purchase from the Amity and shall be repaired or replaced at the sole option and expense of the Amity provided the products alleged to be defective was used for its intended normal use operation and subject to the following qualifications and limitations.
2. Any alteration of product without consent from Amity is strictly forbidden and shall void warranty.
3. No welding shall be performed on finished product.
4. No responsibility is assumed for any malfunctions or damages which are occasionally caused by foreign objects which may be ingested into water system such as, but not limited to stones, sand or metal chips.
5. Amity assumes responsibility for our product, which is defective only, and therefore, it will not assume responsibility for labor to either remove or install our product unless it agrees in writing to assume such responsibility.
6. Unless otherwise approved in writing by the Amity all returns of defective (or allegedly defective products) are at Purchaser’s expense and must include a RGA number issued by the Amity.
7. All warranty claims must be presented at the time the problem occurs, or as soon as practical thereafter, either called or faxed to the Amity and include the numbers on the assembly’s Amity’s label with a detailed explanation of the difficulty in order for the matter to be appropriately evaluated and resolved.
8. Amity will not be held liable for damage incurred during shipment.
9. No responsibility shall be assumed for misuse or improper mounting, unreasonably use or abuse of the Product and or failure to provide or use improper maintenance, failure to follow written installation and use in instruction or any use other than the customary designed use.
THE REMEDIES PROVIDED IN THE ABOVE EXPRESS LIMITED WARRANTY AND ARE THE SOLE AND EXCLUSIVE REMEDIES AVAILABLE. NO OTHER EXPRESS WARRANTIES ARE MADE. ALL IMPLIED
WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR {00046826;v2}
FITNESS FOR A PARTICULAR PURPOSE OR USE ARE LIMITED IN DURATION AS SET FORTH ABOVE. IN NO EVENT SHALL THE AMITY ASSUME OR BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES.
THE WITHIN DESCRIBED WARRANTY SHALL ONLY BE AFFORDED TO THE ORIGINAL PURCHASER OR FOR
INCORPORATION INTO ANOTHER UNIT AND TO FIRST PURCHASER AS PART OF COMPLETED UNIT,
HOWEVER, THE WARRANTY PERIOD OF TEN YEARS COMMENCES UPON INSTALLATION INTO FINAL ASSEMBLY WITH THE UNDERSTANDING IT IS INSTALLED WITHIN SIX MONTHS OF PURCHASE.
Dated: ____________________ ____, 20___
Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 2/8/2010 WA0047
1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL
OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,
INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.
2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.
This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.
THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE
TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.
This limited warranty is applicable to the vehicle in the following percentage costs of warranty repair, if any:
Topcoat Durability & Appearance: Gloss, Color Retention & Cracking
0-24 months 100%
25-48 months 50%
Integrity of Coating System: Adhesion, Blistering/Bubbling 0-24 months 100%
25-48 months 50%
Corrosion: Dissimilar Metal and Crevice
0-24 months 100%
25-48 months 50%
Corrosion Perforation
0-24 months 100%
25-48 months 50%
This limited warranty applies only to exterior paint.
Items not covered by this warranty include:
(a) Damage from lack of maintenance and cleaning (proper cleaning and maintenance procedures are detailed in the Pierce operation and maintenance manual).
(b) UV paint fade.
Conditions and
Exclusions:
See Also
Paragraphs
2 thru 4
Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:
Fire and Rescue Apparatus
Coverage:
Four (4) Year Pro-Rated Paint and Corrosion
Aerial Device
Four (4) Years Warranty Period
Ends After:
The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:
Aerial device shall be free from blistering, peeling, corrosion or any other adhesion defect caused by defective
manufacturing methods or paint material selection for
exterior surfaces.
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;
4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.
Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,
INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,
WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW
OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY
PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS
THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,
REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.
If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.
Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.
3. BUYER'S EXCLUSIVE REMEDY.
| 14233 West Road | Houston TX 77041 | Tel 281.807.4420 | Fax 281.807.4815 | www.harrisonhydragen.com | MANUFACTURER’S LIMITED WARRANTY - HYDRAULIC GENERATORS
STANDARD
Harrison Hydra-Gen® (Seller) extends to the original purchaser (Buyer) of goods for use (whether it be an OEM, dealer, re-seller, or end-user) the following warranty covering the Harrison HydraGen® Generator System, subject to the qualifications indicated. Harrison Hydra-Gen® Generator Systems shall consist of a Harrison generator tray assembly and its’ components, a Harrison hydraulic pump assembly, and a Harrison supplied meter assembly; unless otherwise specified in below guidelines.
Harrison Hydra-Gen® warrants the original purchaser that the Generator System manufactured or supplied by Harrison Hydra-Gen® will be free from defects in materials and workmanship, provided such goods are:
1. Installed, operated and maintained in accordance with the Harrison Hydra-Gen® owner’s manual, and/or written installation addendums.
2. Each new application has been reviewed and approved by the Harrison Hydra-Gen® Application Engineering Group.
PERIOD OF WARRANTY
*Two (2) years or 2000 hours of usage, whichever
comes first, from the date the product is shipped from
Harrison to the Installer.
*The END USER must complete and return to Harrison Hydra-Gen the Harrison HydraGen Warranty Registration Card, Form WR-1, provided in the generator manual and provided online @ www.harrisonhydragen.com, within 45 days of delivery.
Warranty includes all parts and labor. In addition, maintenance items that are contaminated or damaged by a proven warrantable failure are covered in years 1-2, and Labor time up to 4 hours, travel time up to 2.5 hours, and mileage up to 100 miles for warranty related repairs are covered. | 14233 West Road | Houston TX 77041 | Tel 281.807.4420 | Fax 281.807.4815 | www.harrisonhydragen.com | Repair or replacement parts are warranted for ninety (90) days from date of purchase, excluding labor and travel expenses. Any part repaired or replaced during the warranty period assumes the remainder of the warranty or ninety (90) days, whichever is greater.
Only components supplied by Harrison Hydra-Gen are covered under this warranty.
There is no other express warranty. Implied warranties, including merchantability and fitness for a particular purpose, are limited to periods set forth above and to the extent permitted by law. Any and all implied warranties are excluded. In no event is Harrison Hydra-Gen liable for incidental or consequential damages.
The Buyer (OEM, dealer, re-seller, or end-user) must notify Harrison Hydra-Gen, an Authorized Distributor, or a designated Harrison Hydra-Gen Service Representative, in writing, within thirty (30) calendar days after goods or parts failed to meet this warranty.
The sole liability of Harrison Hydra-Gen and the Buyer’s sole remedy for a failure of goods under this warranty and for any and all other claims arising out of the purchase and use of the goods, including negligence on the part of the manufacturer, shall be limited to the repair or replacement of the product, at the option of Harrison Hydra-Gen, of the parts that do not conform to this warranty, provided that the product or parts are returned to the Harrison HydraGen manufacturing facility.
A Returned Goods Authorization (RGA) is required for all products and parts being returned, and may be requested by phone, fax, email, or mail.
Failure to make timely delivery to Harrison Hydra-Gen of the goods claimed to be defective shall void any warranty.
Unless previous written agreements have been made between the Buyer and Harrison HydraGen, the Buyer shall be responsible for all freight and shipping charges in connection with the delivery of the goods claimed to be defective, to Harrison Hydra-Gen at its manufacturing facility, and the return of repaired or replacement goods to the Buyer.
If Harrison Hydra-Gen determines that no warranty coverage is available for goods claimed to be defective, whether determination is based on the warranty being voided, the product failure | 14233 West Road | Houston TX 77041 | Tel 281.807.4420 | Fax 281.807.4815 | www.harrisonhydragen.com | being due to a cause not covered by the warranty, the failure to make a timely and proper warranty claim, or otherwise, the Buyer shall have the option of either:
1. Having the goods not repaired and returned to the Buyer, freight collect.
2. Having the goods repaired, If Harrison Hydra-Gen determines that the product is repairable, and returned to the Buyer, freight collect. The Buyer will be responsible for all costs associated with the repair and testing of the goods and shall authorize Harrison Hydra-Gen, in writing, to have the goods repaired and tested by Harrison Hydra-Gen.
The owner is obligated to operate and maintain the goods in accordance with the recommendations published by Harrison Hydra-Gen in the owner’s manual. The owner is responsible for the costs associated with such maintenance and any adjustments that may be required.
This warranty shall not apply to:
1. Damages or defects caused by normal wear, accident, misuse, abuse, abnormal operating conditions, negligence, corrosion, accident causes, or attributable to written specifications or instructions furnished by the installer.
2. Damages or defects caused by improper maintenance in accordance with the Harrison Hydra-Gen product manuals and operating guidelines.
3. Damages caused by operator error.
4. Damages or defects caused by improper installation.
5. Damages or defects caused by inadequate water drainage provided by the installer in the area where the generator is installed or stored.
6. Damages or defects caused by inadequate air flow space or ventilation provided by the installer in the area where the generator is installed.
7. Any product or part altered or modified by the installer or service facility without written prior consent by Harrison Hydra-Gen.
8. Cost of normal maintenance, adjustments, installation or start-up.
9. Normal wear items and components needing periodic maintenance such a rubber hoses and filters.
10. Excessive labor due to components being concealed in vehicle as a result of installation.
11. Water, road debris, excessive dirt, salt, abrasive particles, or large foreign objects found in the generator.
12. Telephone or other communications expense.
13. Paint, hydraulic fluid, and interconnecting hoses (internal or external to system assemblies). | 14233 West Road | Houston TX 77041 | Tel 281.807.4420 | Fax 281.807.4815 | www.harrisonhydragen.com | This warranty gives you specific legal rights, and you may also have other rights that may vary from state to state or province to province.
No person is authorized to give any other warranties or to assume any other liabilities behalf of Harrison Hydra-Gen, unless made or assumed in writing by an officer of Harrison Hydra-Gen.
Contact Harrison Hydra-Gen for questions regarding your warranty rights and responsibilities at (281) 807-4420; or visit our website at www.harrisonhydragen.com.
Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 2/8/2010 WA0057
1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL
OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,
INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.
2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.
This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.
THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE
TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.
This limited warranty is applicable to the vehicle in the following percentage costs of warranty repair, if any:
Topcoat Durability & Appearance: Gloss, Color Retention & Cracking
0-72 months 100%
73-96 months 50%
97-120 months 25%
Integrity of Coating System: Adhesion, Blistering/Bubbling 0-36 months 100%
37-84 months 50%
85-120 months 25%
Corrosion: Dissimilar Metal and Crevice
0-36 months 100%
37-48 months 50%
49-72 months 25%
73-120 months 10%
Corrosion Perforation
0-120 months 100%
This limited warranty applies only to exterior paint. Paint on the vehicle's interior is warranted only under the Pierce Basic One Year Limited Warranty.
Items not covered by this warranty include:
(a) Damage from lack of maintenance and cleaning (proper cleaning and maintenance procedures are detailed in the Pierce operation and maintenance manual).
(b) UV paint fade.
(c) Any cab not manufactured by Pierce.
Conditions and
Exclusions:
See Also
Paragraphs
2 thru 4
Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:
Fire and Rescue Apparatus
Coverage:
Ten (10) Year Pro-Rated Paint and Corrosion
Custom Body
Ten (10) Years Warranty Period
Ends After:
The date of the original purchase invoice (issued when the product ships from the factory). Warranty Begins:
Exterior surfaces of the body shall be free from blistering, peeling, corrosion or any other adhesion defect caused by defective manufacturing methods or paint material selection. (d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;
4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.
Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,
INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,
WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW
OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY
PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS
THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,
REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.
If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.
Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.
3. BUYER'S EXCLUSIVE REMEDY.
Note: Any Surety Bond, if a part of the sale of the vehicle as to which this limited warranty is provided, applies only to this Pierce Basic One Year Limited Warranty for such vehicle, and not to other warranties made by Pierce in a separate document (if any) or to the warranties (if any) made by any manufacturer (other than Pierce) of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. 2/22/2010 WA0168
1. LIMITED WARRANTY
THE WARRANTY SET FORTH IN PARAGRAPH 1 IS THE SOLE AND EXCLUSIVE WARRANTY GIVEN BY PIERCE. PIERCE HEREBY DISCLAIMS AND EXCLUDES ALL
OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY,
INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY, ANY
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OF TRADE.
2. DISCLAIMERS OF WARRANTIES
The original purchaser may void this warranty in part or in its entirety if the product is repaired or replaced (a) without prior written approval of the Pierce Customer Service Department; or (b) at a facility which has not been approved by Pierce as to technical capability. Any repairs, modifications, alterations or aftermarket parts added after manufacture without the authorization of Pierce may void this warranty.
This limited warranty shall apply only if the product is properly maintained in accordance with Pierce's maintenance instructions and manuals and is used in service which is normal to the particular model. Normal service means service which does not subject the product to stresses or impacts greater than normally result from careful use. If the Buyer discovers a defect or nonconformity, it must notify Pierce in writing within thirty (30) days after the date of discovery, but in any event prior to the expiration of the warranty period.
THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE
TRANSFERRED BY THE BUYER TO ANY SUBSEQUENT USER OR PURCHASER OR TO ANY OTHER PERSON OR ENTITY.
This warranty does not cover damage from lack of
maintenance and cleaning (proper cleaning and maintenance procedures are detailed in the Pierce operation and
maintenance manual).
Conditions and
Exclusions:
See Also
Paragraphs
2 thru 4
Limited Warranty
Subject to the limitations and exclusions set forth below, Pierce Manufacturing provides the following warranty to the Buyer:
(c) any vehicle, chassis or component, part, attachment or accessory that has been repaired, altered or assembled in any way by any person or entity other than Pierce which, in the sole judgment of Pierce, adversely affects the performance, stability or purpose for which it was manufactured; or
(a) any integral parts, components, attachments or trade accessories of or to the product that are not manufactured by Pierce, including but not limited to engines, transmissions, drivelines, axles, water pumps and generators; with respect to all such parts, components, attachments and accessories, Pierce shall assign to Buyer the applicable warranties, if any, made by the respective manufacturers thereof; Notwithstanding anything to the contrary herein, Pierce makes no warranty whatsoever as to:
Fire and Rescue Apparatus
Coverage:
One (1) Year Material and Workmanship
Graphics Fading and Deterioration
One (1) Year Warranty Period
Ends After:
The date the apparatus is placed in service, or 60 days from the original buyer invoice date, whichever comes first. Warranty Begins:
Each graphic lamination shall be free from defects in material, workmanship, fading, and deterioration.
(d) products or parts which may in the ordinary course wear out and have to be replaced during the warranty period, including, but not limited to, tires, fluids, gaskets and light bulbs. Pierce assumes no responsibility for the assembly of its parts or subassemblies into finishing products or vehicles unless the assembly is performed by Pierce. (b) any vehicle, chassis, or component, part, attachment or accessory damaged by misuse, neglect, fire, exposure to severe environmental or chemical conditions, acidic environment, improper maintenance, accident, crash, or force majeure such as natural disaster, lightning, earthquake, windstorm, hail, flood, war or riot;
4. EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.
Notwithstanding anything to the contrary herein or in any agreement between Pierce and Buyer, IN NO EVENT SHALL PIERCE BE LIABLE FOR ANY CONSEQUENTIAL,
INCIDENTAL, SPECIAL, INDIRECT, OR PUNITIVE DAMAGES WHATSOEVER,
WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORY OF LAW
OR EQUITY, WITH RESPECT TO VEHICLES OR OTHER PRODUCTS SOLD BY
PIERCE, OR THEIR OPERATION OR FAILURE TO OPERATE, OR ANY DEFECTS
THEREIN, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATED THERETO,
REGARDLESS OF WHETHER PIERCE HAS BEEN INFORMED OF THE POSSIBILITY OF ANY SUCH DAMAGES. Without limiting the generality of the foregoing, Pierce specifically disclaims any liability for property or personal injury damages, penalties, damages for lost profits or revenues, loss of vehicles or products or any associated equipment, cost of substitute vehicles or products, down-time, delay damages, any other types of economic loss, or for any claims by any third party for any such damages.
If the product fails to conform to the warranty set forth in paragraph 1 during the warranty period, and such nonconformity is not due to misuse, neglect, accident or improper maintenance, Buyer must notify Pierce within the time period specified in paragraph 1, and shall make the product available for inspection by Pierce or its designated agent. At the request of Pierce, any allegedly defective product shall be returned to Pierce by Buyer for examination and/or repair. Buyer shall be responsible for the cost of such transportation, and for risk of loss of or damage to the product during transportation.
Within a reasonable time, Pierce shall repair or replace (at Pierce's option and expense) any nonconforming or defective parts. Repair or replacement shall be made only by a facility approved in advance in writing by Pierce. THIS REMEDY SHALL BE THE EXCLUSIVE AND SOLE REMEDY FOR ANY BREACH OF WARRANTY.
3. BUYER'S EXCLUSIVE REMEDY.
JROGHQVWDWHĆUHFRP
DEALER SUPPLIED
PRODUCTS SERVICES
Exhibit “D”
5 AND
/OR
1 DEALER SUPPLIED EQUIPMENT and/or SERVICES
The following items and/or services will be provided by Golden State Fire Apparatus Inc. (GSFA) and are shown PER UNIT unless otherwise noted:
LICENSED MANUFACTURER
The State of California Vehicle Code, section 11701 requires “every manufacturer of a vehicle subject to registration shall make application to the Department of Motor Vehicles (DMV) for a license containing a general distinguishing number”. The manufacturer has a current license at time of proposal and shall provide a copy upon request. Temporary licenses are not acceptable.
LICENSED DEALERSHIP
The State of California Vehicle Code, section 11701 requires a “dealer in vehicles of a type subject to registration, shall make application to the Department of Motor Vehicles (DMV) for a license containing a general distinguishing number”. Golden State Fire Apparatus, Inc. has a current license at time of bid as outlined above and is available upon request. Temporary licenses are not acceptable.
LICENSED SALES REPRESENTATIVE
The State of California Vehicle Code, section 11800 requires that it shall be “unlawful for any person to function as a vehicle salesperson without having first procured a license issued by the Department of Motor Vehicles (DMV)”. The representative has a current vehicle salespersons license at time of proposal and shall provide a copy upon request. Temporary licenses are not acceptable.
WEEKLY PROGRESS REPORTS
GSFA will provide weekly progress reports including photographs of the apparatus or the major components as they are being constructed. The reports will commence at the start of the manufacturing process and will continue through production by the manufacturer. The reports will show the progress of the apparatus through the course of each week. Special attention will be given to show the unique features and aspects of the apparatus as construction progresses.
VEHICLE REGISTRATION
The State of California Vehicle Code section 11739 requires that the “dealer of a new motor vehicle sale is responsible for applying for the title, securing vehicle registration, and obtaining license plates for the Customer” through the Department of Motor Vehicles (DMV). Golden State Fire Apparatus, Inc. is a factory-authorized dealer of the vehicle being sold and is authorized to register with the State of California as a new vehicle manufacturer.
GSFA will make all necessary applications and complete all transfer papers, including applying for California Exempt “E” license plates.
PRE-CONSTRUCTION, FACTORY TRIP
A pre-construction trip to the manufacturing facility will be provided for four (4) Customer representative(s). The intent of this trip is to review and finalize, in detail, the specifications prior to the start of production. The pre-construction trip will have a duration of four (4) days and three (3) nights and be scheduled at times mutually agreed upon between GSFA. and the Customer. Costs for airfare, lodging, meals, and ground transportation while at the manufacturer’s location will be the responsibility of GSFA.
Air travel will be from one of the following airports: Sacramento, San Francisco, or San Jose.
Costs such as Customer ground transportation in California, Customer airport parking, Customer luggage fees and Customer incidentals while traveling to the factory will be the responsibility of the Customer.
Flight reservations are non-refundable and in the event of a cancellation after booking, the Customer will be responsible for all costs associated with this cancellation, which may include not only the original 2 ticket cost but also any change or cancellation fees imposed by the airline and/ or travel agency. Flight reservations are also non-transferable.
FINAL INSPECTION, FACTORY TRIP
A final inspection trip to the manufacturing facility will be provided for four (4) Customer representative(s). The intent of this trip is to ensure that the apparatus is built to specification and to detect any deficiencies that require correction. The final inspection trip will have a duration of four (4) days and three (3) nights and be scheduled at times mutually agreed upon between GSFA and the Customer. Costs for airfare, lodging, meals, and ground transportation while at the manufacturer’s location will be the responsibility of GSFA. Air travel will be from one of the following airports: Sacramento, San Francisco, or San Jose.
Costs such as Customer ground transportation in California, Customer airport parking, Customer luggage fees and Customer incidentals while traveling to the factory will be the responsibility of the Customer.
Flight reservations are non-refundable and in the event of a cancellation after booking, the Customer will be responsible for all costs associated with this cancellation, which may include not only the original ticket cost but also any change or cancellation fees imposed by the airline and/ or travel agency. Flight reservations are also non-transferable.
CONTINGENCY RESERVE FUND
A contingency reserve fund in the sum of $15,000 is included in the quotation to cover the cost of change orders, unforeseen items due to EPA 2027 motor compliance or required work that may come up during the contract to be used at the discretion of the City of Salinas. This reserve fund is not an estimate of those contingencies, and the cost of change orders, unforeseen items or required work could exceed the amount reserved depending on their nature. Any unused portion of this reserve fund will be credited back on the final invoice or returned in the form of a check to the City of Salinas promptly following final invoicing.
DELIVERY TO AUTHORIZED SERVICE FACILITY
GSFA will, at their expense, deliver the apparatus (including any applicable equipment, spare parts, and supplies) to their Northern California facility in Sacramento for a dealer preparation inspection.
To ensure proper break in of all components while still under warranty, the apparatus shall be delivered under its own power - rail or truck freight shall not be acceptable.
PRE-DELIVERY SERVICE
After transportation from the factory and prior to delivery, the apparatus will receive a pre-delivery service to confirm proper operation and correction of any issues found as a result of said inspection. The Golden State Fire Apparatus, Inc. pre-delivery service consists of the following:
• Engine Compartment and Undercarriage – Check for any broken mounting brackets and inspect for correct capacities of the following (if applicable): engine oil, coolant, power steering fluid, washer reservoir fluid, transmission fluid, rear end fluid, pump transmission oil, and primer oil. • Interior – Operate all doors, windows, and locks for proper adjustment. Check upholstery. • Exterior – Repair reasonable paint scratches or chips. Tighten any loose hardware and inspect tires and wheels for proper pressure and lug torquing.
• Road Test – With the water tank (if applicable) full, the apparatus will be driven approximately twenty miles which allows the drive train components to get up to operating temperature. Road 3 test will be on both city and highway roads. A DOT compliant brake test will be conducted to ensure the system is holding air. The brake condition and wheel seals will also be inspected. • Electrical - Operate all lights, sirens, and other electrical accessories to verify operation. • Pump - If applicable, vacuum test the pump to hold for 15 minutes. After vacuum test, operate the relief valve, transfer valve and check pump shift. Check water tank for leaks and inspect water level gauge for calibration. With discharge caps loose, rapid test all individual gauges and main gauges for calibration. Lubricate valve rods.
• Foam System – If applicable, tighten caps and connect foam lines. Test selector, valves, metering valve and operation of foam system (including flush).
• Fuel Tank - Fuel tank will be filled at the dealership location prior to final delivery. • DEF Tank - DEF tank will be filled at the dealership location prior to final delivery. • Wash - The apparatus will be thoroughly washed at the dealership location prior to final delivery.
FINAL DELIVERY (CUSTOMER LOCATION)
GSFA will, at their expense, deliver the Product (including any applicable equipment, spare parts, and supplies) to the Customer specified address once completed. Prior to delivery of the Product, Customer agrees to provide proof of liability and physical damage insurance to GSFA. GSFA will not release the Product to the Customer until such proof of insurance is provided.
It is the responsibility of the Customer to have any outstanding balance due, paid in full to GSFA, prior to or at the time that the Product is complete and ready to deliver. If payment is late or delivery is delayed pending payment, a daily finance charge of $150.00 and a daily storage fee of $50.00 may apply until such payment is received.
Due to insurance liability, the Product will not be delivered without full acceptance and full payment (or prior written agreement between the Customer and GSFA).
END OF EXHIBIT “D”
City of Salinas
Legislation Text
200 Lincoln Ave., Salinas,
CA 93901
www.cityofsalinas.org
File #: ID#24-278, Version: 1
Modification to the Classification - Salary Schedule, Reclassification, and Workforce Allocation Adjustment
Approve a Resolution modifying the Classification - Salary Schedule to 1) add the classifications of Permit Analyst, Assistant Public Works Director/City Engineer, Retired Annuitant - Senior Civil Engineer, and Senior Wastewater Operator; 2) approve the recommended reclassifications and workforce adjustments in the Community Development Department, Finance and Public Works Departments; 3) approve a recruitment and retention incentive for the Police Services Records Division non-sworn staff (Supervising Police Services Technician and Police Services Technician classifications).
City of Salinas Page 1 of 1 Printed on 5/3/2024
powered by Legistar™
Page | 1
CITY OF SALINAS
COUNCIL STAFF REPORT
DATE: MAY 7, 2024
DEPARTMENT: HUMAN RESOURCES
FROM: MARINA HORTA-GALLEGOS, HUMAN RESOURCES DIRECTOR
TITLE: MODIFICATION TO THE CLASSIFICATION – SALARY
SCHEDULE, RECLASSIFICATION, AND WORKFORCE
ALLOCATION ADJUSTMENT
RECOMMENDED MOTION:
It is recommended that the City Council approve a Resolution modifying the Classification – Salary Schedule to 1) add the classifications of Permit Analyst, Assistant Public Works Director/City Engineer, Retired Annuitant - Senior Civil Engineer, and Senior Wastewater Operator; 2) approve the recommended reclassifications and workforce adjustments in the Community Development Department, Finance and Public Works Departments; 3) approve a recruitment and retention incentive for the Police Services Records Division non-sworn staff (Supervising Police Services Technician and Police Services Technician classifications).
EXECUTIVE SUMMARY:
Staff recommends that the City Council approve the attached Resolution modifying the Classification – Salary Schedule, approve the FY 23-24 workforce allocation adjustment, approve the recommended reclassifications in the Community Development, Finance, and Public Works Departments pursuant to section 3.9 (D) of the Personnel Manual which provides, “Reclassification is generally necessitated through organization modification. Generally, reclassification will result from: 1) Significantly changed duties and responsibilities, necessitating a modification of the pay range and title of the position. 2) Reorganization of a department, or division of a department…,” and approve the recruitment and retention incentive for the Police Services Records Division.
BACKGROUND:
Community Development
Staff recommend reclassifying one incumbent Executive Assistant supporting Community Development to Permit Analyst and adding the classification to the FY 23-24 workforce and to the Classification – Salary Schedule, Association of Management Personnel of Salinas (AMPS) unit. The incumbent was assigned to assist Community Development permit service operations in September 2023. The initial assignment was temporary due to staffing challenges in the Permit Center. Staff immediately recognized the need to reorganize the front counter operations to provide a higher level of customer service, research and analyze front counter operations, application intake/routing, telephone response, and support Permit Center workflow, among other tasks.
Page | 2
The salary range for this classification is:
Additionally, staff recommend reclassifying the following vacant positions, Code Enforcement Officer I to Code Enforcement Officer II, and Administrative Analyst I to Management Analyst.
Finance
Staff recommends the reclassification of the following incumbents to address organizational efficiency and assign classifications that reflect level of responsibility for incumbents as follows, incumbent Purchasing Technician to Senior Accounting Technician, Senior Purchasing Technician to Senior Buyer, and Confidential Office Technician to Administrative Analyst I.
Police
Following recent resignations and promotions from the Police Services Records Division, the Acting Chief, Personnel & Training staff, and Human Resources staff met to review recruitment and retention challenges in the Records Division and recommend a recruitment and retention incentive for twelve non-sworn positions in the Records Division while the City conducts a thorough classification and compensation study for the Police Services Technician series.
As previously noted, the Police Department is a full-service police department operating twenty-four hours per day with an authorized staffing of 157 sworn positions and 54 non-sworn positions. The Department currently has 9 non-sworn vacancies, 5 of which are in the Records Division. The City received 112 applications over the past twelve months. Thirty-three applicants have been invited to interview, 19 have withdrawn from recruitment and 11 failed the background investigation or interview. The challenges with these two classifications are the background investigation, shift schedule (mandatory overtime), twelve-month probationary period, and compensation. Staff has solicited the services of Regional Government Services to conduct an in-depth review of the Page | 3
organizational structure in the Records Division, and a classification and compensation study for the Police Services Technician series.
Staff will continue to meet, review, and return with additional recommendations; however, as an initial and immediate step, staff propose a recruitment and retention incentive of $7,000 for twelve positions. The incentive would be paid in two installments as follows:
Incumbents
Retention Incentive: $3,500 upon Council approval, $3,500 effective in the first full pay period of July 2025.
New Hires
Recruitment Incentive: $3,500 upon hire, $3,500 upon successful completion of the twelve-month probationary period.
The Police Department will utilize salary savings from budgeted, vacant positions to operate the incentive program for a total of approximately $84,000.
Public Works
Staff recommend reactivating the Assistant Public Works Director/City Engineer classification and reclassifying the incumbent City Engineer. This classification is characterized by the responsibility to plan, direct, and review all Public Works engineering activities, managing assigned projects and programs for the Engineering Division, in addition to serving as the department head in the absence of the Director.
Staff recommend adding the classification of Retired Annuitant - Senior Civil Engineer to the Classification – Salary Schedule, to recruit for temporary extra help while staff continue efforts to recruit for two regular vacant Senior Civil Engineer positions.
Staff recommend reclassifying one incumbent Wastewater Operator to Senior Wastewater Operator.
The incumbent Wastewater Operator has been designated as the Chief Plant Operator of the Industrial Wastewater Facility overseeing the day-to-day activities of the facility since 2022.
Lastly, staff recommend reclassifying the vacant Associate Engineer position in the Traffic Division to a Management Analyst. The City has been unsuccessful in filling the vacant Associate Engineer position. A Management Analyst will be able to assist with the more complex administrative and program management functions of the division.
Benefit
Group Grade Position
Step 1
Hourly
Step 1
Monthly
Step 2
Hourly
Step 2
Monthly
Step 3
Hourly
Step 3
Monthly
Step 4
Hourly
Step 4
Monthly
Step 5
Hourly
Step 5
Monthly
Step 6
Hourly
Step 6
Monthly
15 15.5002 Assistant PW Dir/City Engineer 71.9210 12,466 75.5171 13,090 79.2930 13,744 83.2577 14,431 87.4206 15,153 91.7916 15,911 Benefit
Group Grade Position
Step 1
Hourly
Step 2
Hourly
Step 3
Hourly
Step 4
Hourly
Step 5
Hourly
29 Retired Annuitant Senior Civil Engineer 55.8757 58.6657 61.5987 64.6817 67.9155 Benefit
Group Grade Position
Step 1
Hourly
Step 1
Monthly
Step 2
Hourly
Step 2
Monthly
Step 3
Hourly
Step 3
Monthly
Step 4
Hourly
Step 4
Monthly
Step 5
Hourly
Step 5
Monthly
Step 6
Hourly
Step 6
Monthly
25 Senior Wastewater Operator 32.5124 5,635 34.1358 5,917 35.8437 6,213 37.6366 6,524 39.5136 6,849 41.4922 7,192 Page | 4
Page | 5
CEQA CONSIDERATION:
Not a Project. The City of Salinas has determined that the proposed action is not a project as defined by the California Environmental Quality Act (CEQA) (CEQA Guidelines Section 15378).
STRATEGIC PLAN INITIATIVE:
The proposed action meets the Effective and Culturally Responsive Government Council goal.
DEPARTMENTAL COORDINATION:
The above recommendations are a collaborative and coordinated effort between Human Resources and the respective departments.
FISCAL AND SUSTAINABILITY IMPACT:
Community Development: The impact for the balance of the fiscal year is approximately $6,313, $37,880 over twelve months. The increase in permit service this fiscal year will be covered through the Enterprise Fund and the balance will be offset this fiscal year with salary savings.
Finance: The impact for the balance of the fiscal year is approximately $7,355, $44,130 over twelve months. The increase will be offset with salary savings.
Police: The recruitment and retention incentive will result in a cost of approximately $84,000.
Public Works: No fiscal impact is anticipated in this fiscal year as a result of the reclassifications.
The increase in compensation for the Assistant Public Works Director/City Engineer will be offset by the savings from the reclassification of the Associate Engineer to Management Analyst. The impact for the reclassification of the Wastewater Operator is approximately $1,986.00 for the balance of the fiscal year.
ATTACHMENTS:
Resolution
Classification – Salary Schedule (Exhibit A)
Page | 6
RESOLUTION NO. _________ (N.C.S.)
RESOLUTION APPROVING MODIFICATION TO THE
CLASSIFICATION - SALARY SCHEDULE, RECLASSIFICATION, AND WORKFORCE
ALLOCATION ADJUSTMENT
BE IT RESOLVED BY THE CITY COUNCIL OF SALINAS that the Classification-Salary Schedule previously adopted by the City Council by Resolution is hereby amended to include the classifications of Assistant Public Works Director/City Engineer, Permit Analyst, Retired Annuitant – Senior Civil Engineer, and Senior Wastewater Operator; the reclassifications in the Community Development, Finance Department, and Public Works Department are approved. The workforce of the Community Development Department shall reflect one Permit Analyst. The Police Service Technician and Supervising Police Service Technician recruitment and retention incentive is approved.
PASSED AND APPROVED this 7th day of May 2024, by the following vote:
AYES:
NOES:
ABSENT:
ABSTAIN: APPROVED:
____________________________________
Kimbley Craig, Mayor
ATTEST:
______________________________
Patricia M. Barajas, City Clerk
Page | 7
EXHIBIT A
Benefit
Group Grade Position
Step 1
Hourly
Step 1
Monthly
Step 2
Hourly
Step 2
Monthly
Step 3
Hourly
Step 3
Monthly
Step 4
Hourly
Step 4
Monthly
Step 5
Hourly
Step 5
Monthly
Step 6
Hourly
Step 6
Monthly
15 15.5002 Assistant PW Dir/City Engineer 71.9210 12,466 75.5171 13,090 79.2930 13,744 83.2577 14,431 87.4206 15,153 91.7916 15,911 City of Salinas
Legislation Text
200 Lincoln Ave., Salinas,
CA 93901
www.cityofsalinas.org
File #: ID#24-261, Version: 1
a. Pending Litigation - California Government Code Section 54956.9(a), conference with legal counsel regarding Louis Montano, et al. v. City of Salinas, et al. (Monterey County Superior Court Case no. 21CV003635).
City of Salinas Page 1 of 1 Printed on 5/3/2024
powered by Legistar™