City Council and Concurrent Authorities
September 13, 2022

It shall be a requirement under this agreement that any available insurance proceeds broader than or in excess of the specified minimum insurance coverage requirements and/or limits shall be available to the Additional Insured.

Furthermore, the requirements for coverage and limits shall be (1) the minimum coverage and limits specified in this Agreement; or (2) the broader coverage and maximum limits of coverage of any insurance policy or proceeds available to the named Insured; whichever is greater.

The Additional Insured coverage under the CONTRACTOR’s policy shall be “primary and non-contributory” and will not seek contribution from the City of Stockton’s insurance or self-insurance and shall be at least as broad as ISO CG 20 01 04 13.

The limits of insurance required in this agreement may be satisfied by a combination of primary and umbrella or excess insurance. Any umbrella or excess insurance shall contain or be endorsed to contain a provision that such coverage shall also apply on a primary and non-contributory basis for the benefit of the City of Stockton (if agreed to in a written contract or agreement) before the City of Stockton’s own insurance or selfinsurance shall be called upon to protect it as a named insured.

All self-insured retentions (SIR) must be disclosed to the CITY’s Risk Management for approval and shall not reduce the limits of liability. Payment Bond in the amount of the self-insured retention (SIR) may be required.

Policies containing any self-insured retention (SIR) provision shall provide or be endorsed to provide that the SIR may be satisfied by either the named insured or the CITY.

The CITY reserves the right to obtain a full certified copy of any insurance policy and endorsements.

Failure to exercise this right shall not constitute a waiver of right to exercise later.

CONTRACTOR shall maintain insurance as required by this contract to the fullest amount allowed by law and shall maintain insurance for a minimum of five years following the completion of this project. In the event contractor fails to obtain or maintain completed operations coverage as required by this agreement, the City at its sole discretion may purchase the coverage required and the cost will be paid by contractor.

CONTRACTOR agrees to include with all Subcontractors in their subcontract the same requirements and provisions of this agreement including the indemnity and insurance requirements to the extent they apply to the scope of the Subcontractor’s work.

Subcontractors hired by CONTRACTOR agree to be bound to CONTRACTOR and the CITY in the same manner and to the same extent as CONTRACTOR is bound to the CITY under the Contract Documents. Subcontractor further agrees to include these same provisions with any Sub-subcontractor. A copy of the CITY Contract Document Indemnity ATTACHMENT A Local Construction Contract–H.Y. FLOOR AND GAMELINE PAINTING, INC.–PROJECT NO.WC22003 (Updated 12/31/20)

and Insurance provisions will be furnished to the Subcontractor upon request. The General CONTRACTOR shall require all sub-contractors to provide a valid certificate of insurance and the required endorsements included in the agreement prior to commencement of any work and contractor will provide proof of compliance to the City.

4. INDEMNITY AND HOLD HARMLESS. With the exception that this section shall in no event be construed to require indemnification by Contractor to a greater extent than permitted under the public policy of the State of California, Contractor shall indemnify, protect, defend with counsel approved by City and at Contractor’s sole cost and expense, and hold harmless City, its Mayor, Council, officials, representatives, agents, employees, and volunteers from and against any and all claims, causes of action, liabilities, judgments, awards, losses, liens, claims, stop notices, damages, expenses, and costs (including without limitation attorneys’ fees, expert and consultant fees, and other expenses of litigation) of every nature, including, but not limited to, death or injury to persons, or damage to property, which arise out of or are in any way connected with the work performed, materials furnished, or services provided under this Agreement, or from any violation of any federal, State, or municipal law or ordinance, or City Policy, by Contractor or Contractor’s officers, agents, employees, volunteers or subcontractors.

Contractor shall not be obligated to indemnify or defend City for claims finally determined by a court of law or arbitrator to arise from the active negligence or willful misconduct of the City. It is the intent of the Parties that this indemnity obligation is at least as broad as is permitted under California law. To the extent California Civil Code sections 2782, et seq., limit the defense or indemnity obligations of Contractor to City, the intent hereunder is to provide the maximum defense and indemnity obligations allowed by Contractor under the law. The indemnity set forth in this section shall not be limited by insurance requirements or by any other provision of this Agreement.

With exception that this section shall in no event be construed to require indemnification, including the duty to defend, by Contractor to a greater extent than permitted under the public policy of the State of California, the parties agree that Contractor’s duty to defend City is immediate and arises upon the filing of any claim against the City for damages which arise out of or are in any way connected with the work performed, materials furnished, or services provided under this Agreement by Contractor or Contractor’s officers, agents, employees, volunteers or subcontractors. Contractor’s duties and obligations to defend the City shall apply regardless of whether or not the issue of the City’s liability, breach of this Agreement, or other obligation or fault has been determined.

Contractor shall be immediately obligated to pay for City’s defense costs of the claim, including, but not limited to, court costs, attorney’s fees and costs, expert consultant and witness fees and costs, other witness fees, document reproduction costs, arbitration fees, and, if after final judgment an appeal is pursued, all of such costs for the appeal.

At the conclusion of the claim, if there is any determination or finding of sole active negligence or willful misconduct on the part of the City, City will then reimburse Contractor for amounts paid in excess of Contractor’s proportionate share of responsibility for the damages within 30 days after Contractor provides City with copies of all bills and expenses incurred in the defense of the claim(s). It is agreed between the

(Updated 12/31/20) 511
parties that this reimbursement provision assures Contractor is not obligated to defend or indemnify City in an amount greater than provided for under California law, including, without limitation, California Civil Code sections 2782, 2782.6, and 2782.8.

With the exception that this section shall in no event be construed to require indemnification by Contractor to a greater extent than permitted under the public policy of the State of California, and in addition to the other indemnity obligations in this Agreement, Contractor shall indemnify, defend, and hold harmless City, its Mayor, Council, officials, representatives, agents, employees, and volunteers from and against all claims, losses, expenses, and costs including, but not limited to, attorneys’ fees, arising out of any claim brought against the City by an employee, office, agent, or volunteer of Contractor, regardless of whether such claim may be covered by any applicable workers compensation insurance. Contractor’s indemnification obligation is not limited in any way by any limitation on the amount or type of damages, compensation, or benefits payable by or for the Contractor under workers’ compensation acts, disability acts, or other employee benefit acts.

The City’s acceptance of the insurance certificates required under this Agreement does not relieve the CONTRACTOR from its obligation under this paragraph. The indemnification obligations of this section shall survive the termination of this agreement.

Any exceptions to this language may result in a proposal being deemed non-responsive.

CONTRACTOR/Subcontractor's responsibility for such defense and indemnity obligations shall survive the termination or completion of this agreement for the full period of time allowed by law.

The defense and indemnification obligations of this agreement are undertaken in addition to, and shall not in any way be limited by, the insurance obligations contained in this agreement. If any section, subsection, sentence, clause or phrase of this indemnification is for any reason held to be invalid or unconstitutional, such decision shall not affect the validity of the remaining portions of this indemnification.

5. STANDARD PLANS AND SPECIFICATIONS. The performance of said work and the furnishing of said materials shall be executed in accordance with Section 8-1.04B of the City of Stockton Standard Specifications and Plans as adopted on September 27, 2016, by Council Resolution No. 2016-09-27-1213, effective September 27, 2016, and the provisions of the issued project specifications.

The Director of Public Works will furnish CONTRACTOR a weekly statement showing the number of days charged to the contract for the preceding week, the number of days specified for completion of the contract, and the number of days remaining to complete the contract. CONTRACTOR will be allowed one (1) week in which to file a written protest setting forth in what respects said weekly statement is incorrect, otherwise the statement shall be deemed to have been accepted by CONTRACTOR as correct. //
//
ATTACHMENT A Local Construction Contract–H.Y. FLOOR AND GAMELINE PAINTING, INC.–PROJECT NO.WC22003 (Updated 12/31/20)

6. WORKING DAYS. This work shall be diligently prosecuted to completion before the expiration of 90 WORKING DAYS beginning on the tenth calendar day after the date shown on the Notice to Proceed. It is agreed by the parties to the contract that in case all the work called for under the contract in all parts and requirements, is not finished or completed within the number of days as set forth, damage will be sustained by the CITY, and that it is and will be impracticable and extremely difficult to ascertain the actual damage which CITY will sustain in the event of and by reason of such delay; and it is therefore agreed that CONTRACTOR will pay to CITY the sum of THREE HUNDRED FIFTEEN AND NO/100 DOLLARS ($315.00) per day for each and every calendar day's delay in finishing the work in excess of the number of days prescribed; and CONTRACTOR agrees to pay said liquidated damages as herein provided, and in case the same are not paid, agrees that CITY, may deduct the amount thereof from any monies due or that may become due CONTRACTOR under the contract.

It is further agreed that in case the work called for under the contract is not finished and completed in all parts and requirements within the number of days as specified, the CITY shall have the right to increase the number of days or not, as may seem best to serve the interest of CITY, and if the CITY decides to increase the said number of days, the CITY shall further have the right to charge to CONTRACTOR, CONTRACTOR's heirs, assigns or sureties, and to deduct from the final payment for the work, all or any part, as may be deemed proper, the liquidated damages as specified or the actual cost of engineering, inspection, superintendence, and other overhead expenses which are directly chargeable to the contract, and which accrue during the period of such extension, whichever is greater, except the cost of final surveys and preparation of final estimate shall not be included in such charges.

A working day shall not include, nor shall CONTRACTOR be assessed with liquidated damages nor the additional cost of engineering and inspection during any delay beyond the time named for the completion of the work caused by acts of God or of the public enemy, acts of CITY, fire, floods, epidemics, quarantine restrictions, strikes, and freight embargoes and subject to approval by the Director of Public Works, inability to get materials ordered by CONTRACTOR or subcontractor due to such causes provided that CONTRACTOR shall notify the Director of Public Works in writing of the causes of delay within five (5) working days from the beginning of any such delay, and the Director shall ascertain the facts and the extent of the delay, and Director's findings of the facts thereon shall be final and conclusive.

If CONTRACTOR is delayed by reason of alterations made in these specifications, or by any act of the Director of Public Works or of the CITY, not contemplated by the contract, the time of completion shall be extended proportionately and CONTRACTOR shall be relieved during the period of such extension of any claim for liquidated damages, engineering or inspection charges or other penalties. CONTRACTOR shall have no claim for any other compensation for any such delay.

//
//
ATTACHMENT A Local Construction Contract–H.Y. FLOOR AND GAMELINE PAINTING, INC.–PROJECT NO.WC22003 (Updated 12/31/20) 513

7. CONFORMANCE TO APPLICABLE LAWS. Contractor shall comply with all applicable Federal, State, and Municipal laws, rules, and ordinances. Contractor shall not discriminate in the employment of persons or in the provision of services under this Contract on the basis of any legally protected classification, including race, color, national origin, ancestry, sex or religion of such person.
a. TITLE VI
Title VI of the Civil Rights Act of 1964 requires that “no person in the United States shall, on the grounds of race, color, or national origin, be excluded from participation in, be denied the benefits of, or be subjected to discrimination under any program or activity receiving federal financial assistance.” (42 USC Section 2000d)
http://www.dol.gov/oasam/regs/statutes/titlevi.htm.

The City of Stockton requires compliance with the requirements of Title VI in all of its programs and activities regardless of funding source. b. DISCRIMINATION AND HARASSMENT POLICY
The City of Stockton has a Discrimination and Harassment Policy (Exhibit C). The purpose of this policy is to reaffirm the CITY’s commitment to demonstrating respect for all individuals by strictly prohibiting discrimination and harassment, including sexual harassment in the workplace, to define the types of behavior and conduct prohibited by this policy, and to set forth a procedure for reporting, investigating, and resolving complaints of discrimination and harassment in the workplace.
c. LABOR STANDARDS PROVISIONS/CALIFORNIA LABOR CODE
The bidder shall understand that conditions set forth in Chapter 1, Part 7, Division 2 of the California Labor Code shall be considered part of the contract agreement.
https://leginfo.legislature.ca.gov/faces/codes_displayText.xhtml?lawCode= LAB&division=2.&title=&part=7.&chapter=1.&article=2.
d. PREVAILING WAGE
CONTRACTOR and any subcontractor shall pay each employee engaged in the trade or occupation not less than the prevailing hourly wage rate. In accordance with the provisions of Section 1770 of the Labor Code, the Director of Department of Industrial Relations of the State of California has determined the general prevailing wage and employer payments for health and welfare, pension, vacation, travel time, and subsistence pay as provided for in Section 1773.1, apprenticeship or other training programs

(Updated 12/31/20) 514
authorized by Section 3093 and similar purposes applicable to the work to be done. CONTRACTOR performing the work under this contract shall obtain a copy of the wage rate determination and shall distribute copies to each subcontractor. As the wage determination for each craft reflects an expiration date, it shall be the prime CONTRACTOR and each subcontractor's responsibility to insure that the prevailing wage rates of concern is current and paid to the employee.
i. The CONTRACTOR performing the work shall be responsible for obtaining a copy of the State wage rate determination. State wage rates may be obtained at
http://www.dir.ca.gov/OPRL/pwd/Determinations/Northern/Northern.pd f. The CONTRACTOR shall be responsible for posting said wage rates at a prominent location at the work site and shall maintain same in a good readable condition for the duration of the work.
ii. Should the CONTRACTOR choose to work on a Saturday, Sunday or on a holiday recognized by the Labor Unions, the CONTRACTOR shall reimburse the CITY the actual cost of engineering, inspection, superintendence, and or other overhead expenses which are directly chargeable to the contract. Should such work be undertaken at the request of the CITY, reimbursement will not be required. To conform strictly with the provisions of Division 2, Part 7, Chapter 1, Article 2, of the Labor Code of the State of California. To forfeit as a penalty to CITY the sum of TWENTY-FIVE AND NO/100 DOLLARS ($25.00) for each laborer, worker, or mechanic employed by CONTRACTOR, or by any subcontractor under CONTRACTOR, in the execution of this contract, for each calendar day during which any laborer, worker, or mechanic is required or permitted to work more than eight (8) hours and who is not paid the general prevailing rate of per diem wages for holiday and overtime work in violation of the provisions of Sections 1770 to 1781 of the Labor Code of the State of California. That all sums forfeited under the provisions of the foregoing sections shall be deducted from the payments to be made under the terms of this contract.
iii. The CONTRACTOR to whom the contract is awarded shall insure that the prime and each subcontractor will in accordance with Section 1776 of the Labor Code, maintain certified payroll records. A copy of said records shall be provided with each invoice to the Public Works Department, Attention Contract Compliance Officer. It shall be the CONTRACTOR’S responsibility to obtain copies of the current prevailing wage rate determination for all subcontractors. Additionally, certified payroll records must be uploaded to the DIR website as required by labor code.

ATTACHMENT A Local Construction Contract–H.Y. FLOOR AND GAMELINE PAINTING, INC.–PROJECT NO.WC22003 (Updated 12/31/20)

iv. The CONTRACTOR shall comply with the provisions established in Section 1777.5 of the Labor Code concerning the 1) certified approval by local joint apprenticeship committees for the employment and training of apprentices, and 2) contribution of funds to administer and conduct apprenticeship programs, if applicable to the job. e. LOCAL EMPLOYMENT ORDINANCE
Pursuant to Stockton Municipal Code Section 3.68.095 the CONTRACTOR and all subcontractors shall make a good faith effort to employ at least 50 percent of the workforce on this project from local residents, as measured by total labor work hours. Failure of any CONTRACTOR or subcontractor to comply with these requirements shall be deemed a material breach of the contract or subcontract. CONTRACTORS and subcontractors shall maintain records necessary for monitoring their compliance with section

3.68.095.

CITY agrees:

8. COMPENSATION. To pay CONTRACTOR for the work herein
contemplated in the following manner: Progress payments will be made on or about the first day of each calendar month, in such sum as shall make the aggregate of payment up to such day equal to ninety-five percent (95%) of the proportional contract price, upon the basis of the progress certificate of the Director of Public Works as to the amount of work done and the proportional amount of the contract price represented therefore; and all of the remaining part of the contract price not as aforesaid paid, shall be paid at the expiration of thirty-five (35) days from the completion of said work of construction and the certification by the Director of Public Works of such completion.

9. SECURITIES. Pursuant to Section 22300 of the Public Contract Code, CONTRACTOR will be permitted, at its request and sole expense, to substitute securities for any monies withheld by the CITY to ensure performance under the contract. Said securities will be deposited either with the CITY or with a State or federally chartered bank as escrow agent. Securities eligible for this substitution are those listed in Section 16430 of the California Government Code or bank or savings and loan certificates of deposit.

CONTRACTOR shall be the beneficial owner of any securities substituted for monies withheld and shall receive any interest thereon.

10. CHANGE ORDERS. CITY reserves the right to make such alterations, deviations, additions to or omissions from the plans and specifications, including the right to increase or decrease the quantity of any item or portion of the work, as may be deemed by the Engineer to be necessary or advisable and to require such extra work as may be determined by the Engineer to be required for the proper completion or construction of the whole work contemplated.

(Updated 12/31/20) 516
Any such changes will be set forth in a contract change order which will specify, in addition to the work done in connection with the change made, adjustment of contract time, if any, and the basis of compensation for such work. A contract change order will not become effective until approved by the City Manager and/or the City Council.

Processing of change orders shall be in accordance with Section 4-1.05A of the City of Stockton Standard Specifications and Plans as adopted by Council on September 27, 2016, by Resolution No. 2016-09-27-1213, effective September 27, 2016, or as otherwise amended by Council. When the compensation for an item of work is subject to adjustment under the provisions of Standard Specifications and Plans, Section 4-1.05A, CONTRACTOR shall, upon request, promptly furnish the Engineer with adequate detailed cost data for such item of work.

11. AUDITS. CITY reserves the right to periodically audit all charges made by CONTRACTOR to CITY for services under the contract. Upon request, CONTRACTOR agrees to furnish CITY, or a designated representative, with necessary information and assistance.

CONTRACTOR agrees that CITY or its delegate will have the right to review, obtain and copy all records pertaining to performance of the contract. CONTRACTOR agrees to provide CITY or its delegate with any relevant information requested and shall permit CITY or its delegate access to its premises, upon reasonable notice, during normal business hours for the purpose of interviewing employees and inspecting and copying such books, records, accounts, and other material that may be relevant to a matter under investigation for the purpose of determining compliance with this requirement.

CONTRACTOR further agrees to maintain such records for a period of three (3) years after final payment under the contract.
//
//
//
//
//
//
//
//
//
//
//
//
//
//
//

(Updated 12/31/20) 517
ATTACHMENT A 518
ATTACHMENT A EXHIBIT A Page 11 of 34 519
Exhibit B:

Insurance Requirements for Construction Contracts
(Gym Floor Installation WC22003)
Contractor shall procure and maintain for the duration of the contract, and for 5 years thereafter, insurance against claims for injuries to persons or damages to property which may arise from or in connection with the performance of the work hereunder by the Contractor, his agents, representatives, employees, or subcontractors.

MINIMUM SCOPE AND LIMIT OF INSURANCE
Coverage shall be at least as broad as:

1. Commercial General Liability (CGL): Insurance Services Office (ISO) Form CG 00 01 covering CGL on an “occurrence” basis, including products and completed operations, property damage, bodily injury and personal & advertising injury with limits no less than $2,000,000 per occurrence. If a general aggregate limit applies, either the general aggregate limit shall apply separately to this project/location (ISO CG 25 03 or 25 04) or the general aggregate limit shall be twice the required occurrence limit.

2. Automobile Liability: Insurance Services Office Form CA 0001 covering Code 1 (any auto), with limits no less than $1,000,000 per accident for bodily injury and property damage.

3. Workers’ Compensation insurance as required by the State of California, with Statutory Limits, and Employers’ Liability insurance with a limit of no less than $1,000,000 per accident for bodily injury or disease.

4. Surety Bonds as described below.

If the contractor maintains broader coverage and/or higher limits than the minimums shown above, the City of Stockton requires and shall be entitled to the broader coverage and/or the higher limits maintained by the contractor. Any available insurance proceeds in excess of the specified minimum limits of insurance and coverage shall be available to the City of Stockton.

Self-Insured Retentions
Self-insured retentions must be declared to and approved by the City of Stockton. The City of Stockton may require the Contractor to purchase coverage with a lower retention or provide proof of ability to pay losses and related investigations, claim administration, and defense expenses within the retention. The policy language shall provide, or be endorsed to provide, that the self-insured retention may be satisfied by EXHIBIT B Page 12 of 34 ATTACHMENT A 520
either the named insured or City of Stockton. The CGL and any policies, including Excess liability policies, may not be subject to a self-insured retention (SIR) or deductible that exceeds $25,000 unless approved in writing by City of Stockton. Any and all deductibles and SIRs shall be the sole responsibility of Contractor or subcontractor who procured such insurance and shall not apply to the Indemnified Additional Insured Parties. City of Stockton may deduct from any amounts otherwise due Contractor to fund the SIR/deductible. Policies shall NOT contain any self-insured retention (SIR) provision that limits the satisfaction of the SIR to the Named Insured.

The policy must also provide that Defense costs, including the Allocated Loss Adjustment Expenses, will satisfy the SIR or deductible. City of Stockton reserves the right to obtain a copy of any policies and endorsements for verification.

Other Insurance Provisions
The insurance policies are to contain, or be endorsed to contain, the following provisions:

1. The City of Stockton, its officers, officials, employees, and volunteers are to be covered as additional insureds on the CGL policy with respect to liability arising out of work or operations performed by or on behalf of the Contractor including materials, parts, or equipment furnished in connection with such work or operations and automobiles owned, leased, hired, or borrowed by or on behalf of the Contractor.

General liability coverage can be provided in the form of an endorsement to the Contractor’s insurance (at least as broad as ISO Form CG 20 10 11 85 or both CG 20 10, CG 20 26, CG 20 33, or CG 20 38; and CG 20 37 forms if later revisions used).

Additional insured Name of Organization shall read “City of Stockton, its officers, officials, employees, and volunteers.” Policy shall cover City of Stockton, its officers, officials, employees, and volunteers for all locations work is done under this contract.

2. For any claims related to this project, the Contractor’s insurance coverage shall be primary and non-contributory insurance coverage at least as broad as ISO CG 20 01 04 13 as respects the City of Stockton, its officers, officials, employees, and volunteers. Any insurance or self-insurance maintained by the City of Stockton, its officers, officials, employees, or volunteers shall be excess of the Contractor’s insurance and shall not contribute with it. This requirement shall also apply to any Excess or Umbrella liability policies. The City of Stockton does not accept endorsements limiting the Contractor’s insurance coverage to the sole negligence of the Named Insured.

3. Each insurance policy required by this clause shall provide that coverage shall not be canceled, except with notice to the City of Stockton.

Claims Made Policies
EXHIBIT B Page 13 of 34 ATTACHMENT A 521
If any coverage required is written on a claims-made coverage form:

1. The retroactive date must be shown, and this date must be before the execution date of the contract or the beginning of contract work.

2. Insurance must be maintained and evidence of insurance must be provided for at least five (5) years after completion of contract work.

3. If coverage is cancelled or non-renewed, and not replaced with another claims-made policy form with a retroactive date prior to the contract effective, or start of work date, the Contractor must purchase extended reporting period coverage for a minimum of five (5) years after completion of contract work.

4. A copy of the claims reporting requirements must be submitted to the City of Stockton for review.

5. If the services involve lead-based paint or asbestos identification/remediation, the Contractors Pollution Liability policy shall not contain lead-based paint or asbestos exclusions. If the services involve mold identification/remediation, the Contractors Pollution Liability policy shall not contain a mold exclusion, and the definition of Pollution shall include microbial matter, including mold.

Umbrella or Excess Policies
The Contractor may use Umbrella or Excess Policies to provide the liability limits as required in this agreement. This form of insurance will be acceptable provided that all of the Primary and Umbrella or Excess Policies shall provide all of the insurance coverages herein required, including, but not limited to, primary and non-contributory, additional insured, Self-Insured Retentions (SIRs), indemnity, and defense requirements. The Umbrella or Excess policies shall be provided on a true “following form” or broader coverage basis, with coverage at least as broad as provided on the underlying Commercial General Liability insurance. No insurance policies maintained by the Additional Insureds, whether primary or excess, and which also apply to a loss covered hereunder, shall be called upon to contribute to a loss until the Contractor’s primary and excess liability policies are exhausted.

Acceptability of Insurers
Insurance is to be placed with insurers authorized to conduct business in the state with a current A.M. Best rating of no less than A: VII, unless otherwise acceptable to the City of Stockton.

Waiver of Subrogation
Contractor hereby agrees to waive rights of subrogation which any insurer of Contractor may acquire from Contractor by virtue of the payment of any loss.

Contractor agrees to obtain any endorsement that may be necessary to affect this ATTACHMENT A EXHIBIT B Page 14 of 34 522
waiver of subrogation. The Workers’ Compensation policy shall be endorsed with a waiver of subrogation in favor of the City of Stockton for all work performed by the Contractor, its employees, agents and subcontractors.

Verification of Coverage
Contractor shall furnish the City of Stockton with original certificates and amendatory endorsements or copies of the applicable policy language effecting coverage required by this clause and a copy of the Declarations and Endorsements Pages of the CGL and any Excess policies listing all policy endorsements. All certificates and endorsements and copies of the Declarations & Endorsements pages are to be received and approved by the City of Stockton before work commences. However, failure to obtain the required documents prior to the work beginning shall not waive the Contractor’s obligation to provide them. The City of Stockton reserves the right to require complete, certified copies of all required insurance policies, including endorsements required by these specifications, at any time. City of Stockton reserves the right to modify these requirements, including limits, based on the nature of the risk, prior experience, insurer, coverage, or other special circumstances.

Subcontractors
Contractor shall require and verify that all subcontractors maintain insurance meeting all requirements stated herein, and Contractor shall ensure that City of Stockton is an additional insured on insurance required from subcontractors. For CGL coverage, subcontractors shall provide coverage with a form at least as broad as CG 20 38 04 13.

Duration of Coverage
CGL & Excess liability policies for any construction related work, including, but not limited to, maintenance, service, or repair work, shall continue coverage for a minimum of 5 years for Completed Operations liability coverage. Such Insurance must be maintained and evidence of insurance must be provided for at least five (5) years after completion of the contract of work.

Surety Bonds
Contractor shall provide the following Surety Bonds:

1. Bid Bond

2. Performance Bond

3. Payment Bond

4. Maintenance Bond
The Payment Bond and the Performance Bond shall be in a sum equal to the contract price. If the Performance Bond provides for a one-year warranty a separate EXHIBIT B Page 15 of 34 ATTACHMENT A 523
Maintenance Bond is not necessary. If the warranty period specified in the contract is for longer than one year a Maintenance Bond equal to 10% of the contract price is required. Bonds shall be duly executed by a responsible corporate surety, authorized to issue such bonds in the State of California and secured through an authorized agent with an office in California.

Special Risks or Circumstances
City of Stockton reserves the right to modify these requirements, including limits, based on the nature of the risk, prior experience, insurer, coverage, or other circumstances.

Certificate Holder Address
The address for mailing certificates, endorsements and notices shall be:

City of Stockton
Its Officers, Officials, Employees and Volunteers
400 E Main Street, 3rd Floor – HR
Stockton, CA 95202
EXHIBIT B Page 16 of 34 ATTACHMENT A 524
ATTACHMENT A EXHIBIT C Page 17 of 34 525
ATTACHMENT A EXHIBIT C Page 18 of 34 526
ATTACHMENT A EXHIBIT C Page 19 of 34 527
ATTACHMENT A EXHIBIT C Page 20 of 34 528
ATTACHMENT A EXHIBIT C Page 21 of 34 529
ATTACHMENT A EXHIBIT C Page 22 of 34 530
ATTACHMENT A EXHIBIT C Page 23 of 34 531
ATTACHMENT A EXHIBIT C Page 24 of 34 532
ATTACHMENT A EXHIBIT C Page 25 of 34 533
ATTACHMENT A EXHIBIT C Page 26 of 34 534
ATTACHMENT A EXHIBIT C Page 27 of 34 535
ATTACHMENT A EXHIBIT C Page 28 of 34 536
ATTACHMENT A EXHIBIT C Page 29 of 34 537
ATTACHMENT A EXHIBIT C Page 30 of 34 538

BOND FOR FAITHFUL PERFORMANCE
KNOW ALL MEN BY THESE PRESENTS:

That we, H.Y. FLOOR AND GAMELINE PAINTING, INC., a STATE OF CALIFORNIA CORPORATION, as Principal and
, a corporation, organized and existing under the laws
of the State of and duly authorized to transact business under the laws of the State of California, as Surety, are held and firmly bound unto the City of Stockton, a municipal corporation, duly created and existing under and by virtue of the laws of the State of California, as obligee, in the just and full sum of ONE HUNDRED NINETY THOUSAND SIX HUNDRED AND FOUR 00/100 DOLLARS ($190,604.00), in lawful money of the United States of America (being 100% of the contract price) for the payment whereof well and truly to be made to the said CITY, the said Principal and Surety bind themselves, their successors and assigns, jointly and severally, firmly by these presents.

The condition of the foregoing obligation is such that the above bounded Principal has simultaneously entered into a contract with the CITY, to do and perform the following work, to wit:

VAN BUSKIRK COMMUNITY CENTER GYM FLOOR REPLACEMENT
(PROJECT NO. WC22003)
NOW, THEREFORE, if the above bounded Principal, CONTRACTOR, Company or
Corporation or its subcontractor, shall well and truly perform the work contracted to be done under said contract, then this obligation to be null and void; otherwise to remain in full force and effect.

No prepayment or delay in payment and no change, extension, addition or alteration of any provision of said contract, or in said plans or specifications agreed to between the said CONTRACTOR and the said CITY, and no forbearance on the part of the said CITY shall operate to relieve any Surety or Sureties from liability on this bond, ATTACHMENT A Page 31 of 34 539
and consent by said Surety is hereby given, and the said Surety hereby waives the provisions of Sections 2819 and 2845 of the Civil Code of the State of California.

SIGNED AND SEALED on
APPROVED AS TO SURETY: By:

PRINCIPAL
SURETY
APPROVED AS TO FORM & CONTENT:

LORI M. ASUNCION

ACTING CITY ATTORNEY
By:

ATTORNEY-IN-FACT
By:

DEPUTY CITY ATTORNEY

BOND FOR LABOR AND MATERIAL
KNOW ALL MEN BY THESE PRESENTS:

That we, H.Y. FLOOR AND GAMELINE PAINTING, INC., a (STATE CALIFORNIA CORPORATION, as Principal and ,
corporation, organized and existing under the laws of the State of and duly authorized to transact business under the laws of the State of California, as Surety, are held and firmly bound unto the City of Stockton, a municipal corporation, duly created and existing under and by virtue of the laws of the State of California, and unto any and all material suppliers, persons, companies, or corporations furnishing materials, provisions, provender or other supplies used in, upon, for or about the performance of the work contemplated to be executed or performed under the contract hereinafter mentioned, and all persons, companies, or corporations renting or hiring teams, or implements of machinery, for or contributing to said work and all persons who perform work or labor upon the same, and all persons who supply both work and materials, and whose claims have not been paid by the contractor, company or corporation in the just and full sum of ONE HUNDRED NINETY THOUSAND SIX HUNDRED AND FOUR 00/100 DOLLARS ($190,604.00), in lawful money of the United States of America (being 100% of the contract price) for the payment whereof well and truly to be made to said CITY and to said persons jointly and severally, the said principal and Surety bind themselves, their successors and assigns, jointly and severally, firmly by these presents.

The condition of the foregoing obligations is such that the above bounden Principal has simultaneously entered into a contract of even date herewith, with the CITY, to do and perform the following work, to-wit:

VAN BUSKIRK COMMUNITY CENTER GYM FLOOR
(PROJECT NO. WC22003)
NOW, THEREFORE, if the above bounden Principal, CONTRACTOR, Company or Corporation or its subcontractor, fail to pay for all materials, provisions, provender, or other supplies, or teams, used in, upon, for or about the performance of the work contracted to be done, or for any work or labor done thereon of any kind, the Surety on

REPLACEMENT
ATTACHMENT A Page 33 of 34 541
this bond will pay the same, in an amount not exceeding the sum specified in this bond, provided that any and all claims hereunder shall be filed and proceedings had in connection therewith as required by the provisions of Division 3, Part 4, Title 15, Chapter 5, Article 1 of the Civil Code of California, provided that in case suit is brought upon this bond, a reasonable attorney's fee shall be awarded by the Court to the prevailing party in said suit; said attorney's fee to be fixed as costs in said suit, and to be included in the judgment therein rendered.

No prepayment or delay in payment and no change, extension, addition or alteration of any provision of said contract or in said plans or specifications agreed to between the said CONTRACTOR and the said CITY and no forbearance on the part of the said CITY shall operate to relieve any surety or sureties from liability on this bond, and consent to make such alterations without further notice to or consent by any such surety is hereby given, and the said sureties hereby waive the provisions of Sections 2819 and 2845 of the Civil Code of the State of California.

SIGNED AND SEALED on .

APPROVED AS TO SURETY: By:

PRINCIPAL
SURETY
APPROVED AS TO FORM & CONTENT:

LORI M. ASUNCION

ACTING CITY ATTORNEY
By:

ATTORNEY-IN-FACT
By:

DEPUTY CITY ATTORNEY

City of Stockton
Legislation Text
File #: 22-0817, Version: 1

ADOPT RESOLUTION TO PURCHASE ONE FIRE ENGINE

RECOMMENDATION
It is recommended that the City Council adopt a resolution to:

1. Approve findings pursuant to Stockton Municipal Code section 3.68.070 in support of an exception to the competitive bidding process.

2. Approve the use of a Cooperative Purchasing Agreement through Sourcewell Contract No. 113021 to provide the City access to preferential pricing of firefighting apparatus from Pierce Manufacturing, Inc.

3. Authorize the City Manager to execute a contract in the amount of $776,401.10 with Pierce Manufacturing, Inc. through affiliated vendor, Golden State Fire Apparatus of Sacramento, CA, to purchase one fire engine.

It is also recommended that the City Manager be authorized to take appropriate and necessary actions to carry out the purpose and intent of this resolution.

Summary
On September 14, 2021, Council approved the use of $78,052,072.00 in American Rescue Plan (ARP) Coronavirus State and Local Fiscal Recovery Funds. The purchase of various fire apparatus and equipment were identified as eligible expenses, including fire engines.

Sourcewell is a public agency based in Minnesota that issues Cooperative Purchasing Agreements to simplify the procurement process for public agencies and take advantage of volume purchasing. Use of a Cooperative Purchasing Agreement streamlines administrative costs and procedures while maintaining the integrity of the competitive bidding process. The specifications for the fire engine available through Sourcewell meet the City’s requirements for this type of equipment.

It is recommended that Council adopt a resolution authorizing the City Manager to execute a Cooperative Purchasing Agreement through Sourcewell, formerly National Joint Powers Alliance (NJPA), for the purchase of one fire engine from Pierce Manufacturing, Inc. through affiliated vendor, Golden State Fire Apparatus of Sacramento, CA, for a total cost of $776,401.10.

City of Stockton Page 1 of 3 Printed on 9/7/2022
powered by Legistar™
543
File #: 22-0817, Version: 1

DISCUSSION
Background
On September 14, 2021, Council approved the use of $78,052,072.00 in ARP Coronavirus State and Local Fiscal Recovery Funds. The purchase of various fire apparatus and equipment were identified as eligible expenses, including fire engines.

The goals and objectives defined an initial purchase of six fire engines, specifically 1500 GPM Pierce Enforcer Pumper Engines and included a second round of purchases that may include additional fire engines, a ladder truck, and/or equipment to support the Fire Department’s operations.

The City’s fleet of heavy fire equipment consists of 17 fire engines and five ladder trucks. The equipment is maintained by the Fleet Division of the Public Works Department. The Stockton Fire Department operates the equipment and responds daily with 12 of the 17 fire engines and three of the five ladder trucks. The remaining units are in reserve status, to be used when any of the daily response units are out of service. The oldest fire engine is a 1994 model, and the newest is a 2018 model.

The City utilizes a 15-year Heavy Fire Vehicle Replacement Plan to provide a sustainable, reliable, and cost-effective fleet of heavy fire equipment in alignment with industry standards. The National Fire Protection Association Standards for Fire Department Apparatus (NFPA 1901) suggests that replacement cycles for busy fire fleets be evaluated based on call load, maintenance costs, safety, and needed technology updates. The industry standard is between 12 to 20 years for first line response units depending on local conditions, community demand, engine hours, miles driven, and maintenance costs.

Present Situation
The department has identified an additional fire engine, a 2005 Pierce Unit E18, that is due for replacement according to the City’s Fleet Replacement Plan.

The Public Works Department recommends the purchase of one fire engine from Pierce Manufacturing, Inc. through affiliated vendor, Golden State Fire Apparatus of Sacramento, CA, for a total cost of $776,401.10. The specifications for the fire engine available through Sourcewell meet the City’s requirements for this type of equipment and is consistent with the recent purchase of six fire engines through Golden State Fire Apparatus of Sacramento, CA.

Sourcewell is a public agency based in Minnesota that serves as a municipal contracting agency to streamline the procurement process for public agencies and takes advantage of volume purchasing.

All Sourcewell contracts have been competitively bid, solicited nationally, reviewed, evaluated by a committee, and recommended to the Sourcewell Board of Directors for consideration of award. The use of these contracts is optional and is available to California State and local government agencies.

The recommended resolution authorizes the City Manager to execute one Cooperative Purchasing Agreement through Sourcewell, formerly NJPA, for a total of $776,401.10 for the purchase of one fire City of Stockton Page 2 of 3 Printed on 9/7/2022
powered by Legistar™
544
File #: 22-0817, Version: 1
engine with Pierce Manufacturing, Inc. through affiliated vendor, Golden State Fire Apparatus of Sacramento, CA.

Findings
Pursuant to Stockton Municipal Code (SMC) section 3.68.070, Council may approve findings which support an exception to the competitive bidding process. These findings include:

1. Sourcewell established a Cooperative Purchasing Agreement for the purchase of one fire engine with Pierce Manufacturing, Inc.

2. The Pierce Manufacturing, Inc. Cooperative Purchasing Agreement was established pursuant to formal competitive bidding processes conducted by Sourcewell on behalf of its governmental members, of which the City is one.

3. Taking advantage of the leveraged procurement agreement negotiated by Sourcewell will save the administrative expense of City staff conducting separate procurements.

4. The specifications for the equipment available through the Sourcewell contract meet the City’s requirements for their equipment type.

FINANCIAL SUMMARY
There is sufficient funding in Project No. MARPA00/WARP101, Account No. ARPA 280-282, to fund the purchase of one fire engine from Pierce Manufacturing, Inc. through Golden State Fire Apparatus in the amount of $776,401.10.

Below is the purchase breakdown:

Unit Price Total $ 773,346.39
Sourcewell Discount $ (36,272.00)
Pre-Payment Discount $ (24,789.44)

9.00% Sales Tax $ 64,105.65
Fees $ 10.50
TOTAL PURCHASE PRICE $ 776,401.10
There is no impact to the City’s General Fund or any other unrestricted fund as a result of taking the recommended actions.

City of Stockton Page 3 of 3 Printed on 9/7/2022
powered by Legistar™
545
Resolution No.

STOCKTON CITY COUNCIL

RESOLUTION APPROVING FINDINGS AND COOPERATIVE PURCHASING

AGREEMENT THROUGH SOURCEWELL FOR THE PURCHASE OF ONE FIRE ENGINE
The purchase of one fire engine is recommended; and
Sourcewell, formerly National Joint Powers Alliance, is a public agency based in Minnesota that serves as a municipal contracting agency. The use of these contracts is optional and is available to California State and local government agencies; and Sourcewell has a contract with Pierce Manufacturing, Inc. for preferential pricing of one fire engine. The specifications for the unit through the Sourcewell contract meet the City’s requirements for their equipment type; and
The Cooperative Purchasing Agreement that includes Golden State Fire Apparatus of Sacramento, CA, and other vendors was established pursuant to formal competitive bidding processes conducted by Sourcewell on behalf of its governmental members, of which the City is one; and
For the purchase of one fire engine, staff recommends utilizing a Sourcewell contract with Pierce Manufacturing, Inc. through affiliated vendor Golden State Fire Apparatus of Sacramento, CA, in the amount of $776,401.10; now, therefore,

BE IT RESOLVED BY THE CITY COUNCIL OF THE CITY OF STOCKTON, AS FOLLOWS:

1. The City Council hereby approves the following findings in support of granting an exception to the competitive bid process pursuant to Stockton Municipal Code section 3.68.070:
a. Sourcewell established a Cooperative Purchasing Agreement with Pierce Manufacturing, Inc. for the purchase of one fire engine. b. The Pierce Manufacturing, Inc. Cooperative Purchasing Agreement was established pursuant to formal competitive bidding processes conducted by Sourcewell on behalf of its governmental members, of which the City is one. c. Taking advantage of the leveraged procurement agreement negotiated by Sourcewell will save the administrative expense of City staff conducting a separate procurement.
546
d. The specifications for the fire engine available through the Sourcewell contract meet the City’s requirements for their equipment type.

2. The City Council hereby authorizes the use of a Cooperative Purchasing Agreement through Sourcewell Contract No. 113021 to provide the City access to preferential pricing of one fire engine from Pierce Manufacturing, Inc.

3. The City Council hereby authorizes the City Manager to execute a contract in the amount of $776,401.10 with Pierce Manufacturing, Inc. through affiliated vendor, Golden State Fire Apparatus of Sacramento, CA, to purchase one fire engine, a copy of which is attached is Exhibit 1 and incorporated by this reference.

4. The City Manager is hereby authorized to take whatever actions are necessary and appropriate to carry out the purpose and intent of this Resolution.

PASSED, APPROVED, and ADOPTED September 13, 2022 .

KEVIN J. LINCOLN II
Mayor of the City of Stockton
ATTEST:

ELIZA R. GARZA, CMC
City Clerk of the City of Stockton
547

COOPERATIVE/PIGGYBACK PURCHASE AGREEMENT
AGREEMENT SUMMARY:

1. Cooperative/Piggyback
Name:

Sourcewell

2. Contractor: Pierce Manufacturing, Inc. & authorized Pierce dealer, Golden State Fire Apparatus, Inc.

3. Cooperative Agency
Agreement Name and
Agreement Number:

Sourcewell, Firefighting Apparatus, #113021-OKC-1

4. Cooperative Agency Initial
Agreement Term:

Start Date: 02/10/2022
End Date: 02/10/2026

5. Cooperative Agency’s
Agreement-Options to
extend:

Agreement may be extended for one additional year.

6. Cooperative Agency
Amended Term:

Start Date: N/A
End Date: 02/10/2026

7. Cooperative Agency
Remaining Options to
Renew:
1 one-year renewal option remaining.

8. City of Stockton
Cooperative Purchase
Agreement Term:

Start Date: upon execution
End Date: 02/10/2026

9. City of Stockton
Cooperative/ Piggyback
Purchase Agreement
Amount:

Not to Exceed $776,401.10 for the term of the
Agreement.

AGREEMENT
The City of Stockton, a California municipal corporation on behalf of itself and its associated entities ("City"), and the above-named Contractor (“Contractor”), do hereby agree that City shall be granted the pricing, terms, and conditions under the above referenced Sourcewell, Firefighting Apparatus, #113021-OKC-1 (“COOP”) as such may be amended from time to time. The COOP and associated documents referenced in the agreement are incorporated herein as Exhibit A to this City Cooperative/Piggyback Purchase Agreement (“Agreement”).

EXHIBIT 1 548
Contractor shall grant such pricing, terms, and conditions to City for all procurements of goods and services, whether taking place on a City purchase order, purchasing card (credit card), or other purchasing modality, whether via telephone, via the Contractor website, or via direct purchase at a Contractor retail location.

1. Agreement Term: The Term of this Agreement shall remain in effect upon execution through 02/10/2026 unless terminated earlier by the City. If the Cooperative/Piggyback Agency extends the COOP with Contractor by a written amendment, the City has the option to extend the term of this Agreement by written amendment not to go beyond the term stated in the COOP fully executed amendment.

2. Insurance and Hold Harmless: In addition to the pricing, terms and conditions stated in the COOP and the associated documents incorporated herein as Exhibit A, Contractor shall, at Contractor’s sole cost and expense and for the full term of the Agreement or any extension thereof, obtain and maintain at least all the insurance requirements listed in attached Exhibit B.

To the fullest extent permitted by law, Contractor shall hold harmless, defend at its own expense, and indemnify the City of Stockton, its officers, employees, agents, and volunteers, against any and all liability, claims, losses, damages, or expenses, including reasonable attorney’s fees, arising from all acts or omissions of contractor or its officers, agents, or employees in rendering services under this contract; excluding, however, such liability, claims, losses, damages, or expenses arising from the City of Stockton’s sole negligence or willful acts. The duty to defend and the duty to indemnify are separate and distinct obligations. The indemnification obligations of this section shall survive the termination of this Agreement.

3. Compensation: City and Contractor do hereby enter into this Agreement for Firefighting Apparatus available in the above-named COOP and associated documents incorporated herein as Exhibit A and referenced in the attached quote Exhibit C. In no way, shall payment to the Contractor during the term of this Agreement exceed $776,401.10 for the purchase of one fire engine. Any person signing this Agreement on behalf of City or Contractor does warrants that he or she has full authority to do so.

4. Governing Law. California law shall govern any legal action pursuant to this Agreement with venue for all claims in the Superior Court of the County of San Joaquin, Stockton Branch or, where applicable, in the Federal District Court of California, Eastern District, Sacramento Division.

This Agreement may be amended only by a written amendment, consistent with the COOP, signed by Contractor and City.

EXHIBIT 1 549
CITY OF STOCKTON PIERCE MANUFACTURING, INC. &

AUTHORIZED PIERCE DEALER,

GOLDEN STATE FIRE
APPARATUS, INC.

By: __________________________
Harry Black, City Manager Signature

____________________________
Print name
ATTEST: Title: ________________________

____________________________ [If Contractor is a corporation, signatures must Eliza R. Garza CMC, City Clerk comply with Corporations Code §313] APPROVED AS TO FORM:

By: __________________________
___________________________ Signature
City Attorney,
__________________________
Print name
Title: _______________________
EXHIBIT 1 550

EXHIBIT A

PAGE INTENTIONALLY LEFT BLANK
EXHIBIT 1 551
Pierce Manufacturing #113021-OKC
Pricing for contract #113021-OKC for Pierce's unpublished options is provided at a 5.5% discount.

Additional discounts may be available for identical multi-unit purchases. Discount varies dependent on the number of identical units, the configuration of the units, and will be handled on as case by case basis.

Authorized Pierce dealers may offer service contracts for preventative maintenance and other services.

Pricing would be quoted on a time and material bases, by the dealer, at the time of request. Pierce offers our dealers the ability to offer/develop custom service/maintenance contracts to Sourcewell members utilizing this contract.

EXHIBIT 1 552

SOURCEWELL

STATE OF MINNESOTA
Member______________ moved the adoption of the following Resolution:

RESOLUTION TO APPROVE SOLICITATION AND/OR RE-SOLICITATION OF CATEGORIES Resolution No. 2021-22
WHEREAS, Sourcewell desires to issue a solicitation, and is seeking permission from the Board to issue a solicitation, for the categories listed on Appendix A, which is attached and incorporated.

WHEREAS, through the Sourcewell Procurement Policy, the Board designated the Chief Procurement Officer to administer Sourcewell’s cooperative purchasing and contracting program; and WHEREAS, the Chief Procurement Officer recommends approval of categories detailed above.

NOW THEREFORE BE IT RESOLVED that the Board of Directors hereby approves the solicitation of categories.

The motion for the adoption of the foregoing resolution was duly seconded by Member ______________ and the following voted in favor: (list names here)
and the following voted against: (list names here or “NONE”) whereupon said resolution was declared duly passed and adopted.

ATTEST:
_________________________________
Clerk to the Board of Directors
DocuSign Envelope ID: CB1B5FE1-6EAF-4F19-BCA5-34042E31634F Wilson, Zylka, Veronen, Nagel, Thomas, Thiel, Arts and Kircher Thiel
Thomas
None
EXHIBIT 1 553

APPENDIX A

SOURCEWELL PROCUREMENT DEPARTMENT
BOARD ITEMS ‐ September 2021

NEW CONTRACTS
Supplier Name Contract Number Solicitation Title
Carrier Global Corporation 070121‐CAR "HVAC Systems and Related Services" HMI Industries, Inc. 070121‐HMI "HVAC Systems and Related Services" Honeywell International, Inc. 070121‐HNY "HVAC Systems and Related Services" Johnson Controls, Inc. 070121‐JHN "HVAC Systems and Related Services" Juice Technologies, Inc. 070121‐JUC "HVAC Systems and Related Services" Siemens Industry, Inc. 070121‐SIE "HVAC Systems and Related Services" 22nd Century Technologies, Inc. 071321‐CEN "IT Managed Service and Staff Augmentation Solutions" CDW Government, LLC 071321‐CDW "IT Managed Service and Staff Augmentation Solutions" Computer Aid, Inc. 071321‐CAI "IT Managed Service and Staff Augmentation Solutions" Infojini, Inc. 071321‐INF "IT Managed Service and Staff Augmentation Solutions" Judge Technical Services 071321‐JDG "IT Managed Service and Staff Augmentation Solutions"

CONTRACT EXTENSIONS
Supplier Name Contract Number Solicitation Title
Alamo Group, Inc. 052417‐AGI
"Roadway Maintenance Equipment with Related
Accessories, Attachments, Materials and Supplies"
NEW ezIQC CONTRACTS
Company Name Contract Number State ‐ Region ‐ Type of Work ezIQC RENEWALS
Company Name Contract Number
PRIDE Industries One, Inc. CA04‐NCC‐GB03‐080719‐PIO
PRIDE Industries One, Inc. CA03‐NCV‐E01‐080719‐PIO
American Chiller Service, Inc. CA03‐NCV‐M03‐080719‐ACH
Staples Construction Company CA03‐NCV‐GB04‐080719‐STA
PUB Construction, Inc. CA08‐SCI‐GB01‐080719‐PUB
PRIDE Industries One, Inc. CA03‐NCV‐GB03‐080719‐PIO
PRIDE Industries One, Inc. CA03‐NCV‐GEP01‐080719‐PIO
Vincor Construction, Inc. CA08‐SCI‐GB02‐080719‐VCI
Mark Scott Construction CA04‐NCC‐GB02‐080719‐MSC
ACCO Engineered Systems, Inc. CA03‐NCV‐M02‐080719‐AES
PRIDE Industries One, Inc. CA03‐NCV‐M01‐080719‐PIO
Rite‐Way Roof Corporation CA08‐SCI‐R01‐080719‐RWR
Aztec Consultants CA04‐NCC‐GB04‐080719‐AZC
PRIDE Industries One, Inc. CA04‐NCC‐E02‐080719‐PIO
Vincor Construction, Inc. CA09‐SDI‐GB02‐080719‐VCI
Sylvester Roofing Co., Inc. CA09‐SDI‐R01‐080719‐SRC
All Source Tile, Inc. CA09‐SDI‐F02‐080719‐AST
PUB Construction, Inc. CA09‐SDI‐F01‐080719‐PUB
G Team Landscape Construction, Inc. CA08‐SCI‐L01‐080719‐GTL Horizons Construction Co. Int'l, Inc. CA08‐SCI‐DA01‐080719‐HCC Sol Construction CA08‐SCI‐GEP02‐080719‐SOL
PRIDE Industries One, Inc. CA08‐SCI‐GB10‐080719‐PIO

CONSENT AGENDA ITEMS
Private Exchange Technology and Services
Used Firefighting Apparatus and Fire Service Vehicle Solutions State of Florida ‐ Indefinite Delivery Indefinite Quantity Construction Underground Infrastructure Inspection and Rehabilitation Equipment with Related Services Requesting Board permission to Re‐Solicit the following categories:

Requesting Board permission to Solicit the following categories:

Firefighting Apparatus and Fire Service Vehicles with Related Equipment, Options, and Services EXHIBIT 1 554
APPENDIX A Continued
PRIDE Industries One, Inc. CA04‐NCC‐GEP01‐080719‐PIO
All Source Coatings, Inc. CA09‐SDI‐P02‐080719‐ASC
Ausonio, Inc. CA04‐NCC‐GB05‐080719‐AUS
Horizons Construction Co. Int'l, Inc. CA08‐SCI‐GB03‐080719‐HCC Angeles Contractor, Inc. CA08‐SCI‐F02‐080719‐ACI
All Source Coatings, Inc. CA09‐SDI‐GB03‐080719‐ASC
US National Corp dba Jimenez Painting Company CA09‐SDI‐P03‐080719‐USN Harry H. Joh Construction, Inc. CA08‐SCI‐E02‐080719‐HJC Gkkworks Construction Services CA08‐SCI‐GB06‐080719‐GKK J & H Engineering General Contracts, Inc. CA08‐SCI‐GEP03‐080719‐JHE Facility Solutions Group CA08‐SCI‐E01‐080719‐FSG
Angeles Contractor, Inc. CA08‐SCI‐GB05‐080719‐ACI
Horizons Construction Co. Int'l, Inc. CA08‐SCI‐GEP01‐080719‐HCC PUB Construction, Inc. CA08‐SCI‐P01‐080719‐PUB
Angeles Contractor, Inc. CA09‐SDI‐GB06‐080719‐ACI
PUB Construction, Inc. CA09‐SDI‐GB01‐080719‐PUB
Harry H. Joh Construction, Inc. CA09‐SDI‐GB05‐080719‐HJC Angeles Contractor, Inc. CA09‐SDI‐F03‐080719‐ACI
Harry H. Joh Construction, Inc. CA08‐SCI‐GB04‐080719‐HJC PUB Construction, Inc. CA08‐SCI‐F01‐080719‐PUB
PUB Construction, Inc. CA09‐SDI‐P01‐080719‐PUB
Harry H. Joh Construction, Inc. CA08‐SCI‐P02‐080719‐HJC LDCo., Inc. CA09‐SDI‐GB04‐080719‐LDC
ezIQC CONTRACT EXTENSIONS
Company Name Contract Number
EXHIBIT 1 555

SOURCEWELL

STATE OF MINNESOTA
Member ____________ moved the adoption of the following Resolution:

RESOLUTION TO RATIFY COOPERATIVE CONTRACTING AWARDS
2/15/2022
Resolution No. 2022-06
WHEREAS, the Sourcewell Board of Directors previously authorized the solicitations for the cooperative categories listed on Appendix A, which is attached and incorporated; and WHEREAS, Sourcewell issued the cooperative contracting solicitations for the authorized categories; and

WHEREAS, through the Sourcewell Procurement Policy, the Board designated the Chief Procurement Officer to administer Sourcewell’s cooperative purchasing and contracting program and to award all competitively solicited contracts, without limitation; and
WHEREAS, the Chief Procurement Officer made the awards listed based on the results of the competitive solicitation process; and
WHEREAS, the Board acknowledges that the awards made by the Chief Procurement Officer are valid and binding; however, based upon some members’ legal requirements the Chief Procurement Official is required to seek subsequent Board ratification of all cooperative purchasing awards.

NOW THEREFORE BE IT RESOLVED by the Board of Directors ratifies the cooperative contracting awards made by the Chief Procurement Officer listed on Appendix A.

The motion for the adoption of the foregoing resolution was duly seconded by Member______________ and the following voted in favor: (list names here)
and the following voted against: (list names here or “NONE”) whereupon said resolution was declared duly passed and adopted.

ATTEST:
_________________________________
Clerk to the Board of Directors










 
 



























EXHIBIT 1 556

APPENDIX A

SOURCEWELL PROCUREMENT DEPARTMENT
BOARD ITEMSͲFebruary 2022

NEW CONTRACTS
Supplier Name Contract Number Solicitation Title
Gold Star Foods, Inc. 111621ͲGSF
"Food Products and Distribution for School Food Authorities with Related Supplies, Technology and Services"
Sysco Corporation 111621ͲSYC
"Food Products and Distribution for School Food Authorities with Related Supplies, Technology and Services"
US Foods, Inc. 111621ͲUSF
"Food Products and Distribution for School Food Authorities with Related Supplies, Technology and Services"
Custom Fire Apparatus, Inc. 113021ͲCSM "Firefighting Apparatus and Fire Service Vehicles" HME, Inc. 113021ͲHME "Firefighting Apparatus and Fire Service Vehicles" MaxiͲMetal Inc. 113021ͲMAX "Firefighting Apparatus and Fire Service Vehicles" Oshkosh Corporation 113021ͲOKC "Firefighting Apparatus and Fire Service Vehicles" P.L. Custom Body and Equipment Co., Inc. 113021ͲPLC "Firefighting Apparatus and Fire Service Vehicles" Rev Group, Inc. 113021ͲRCG "Firefighting Apparatus and Fire Service Vehicles" Rock River Industries, LLC 113021ͲRCK "Firefighting Apparatus and Fire Service Vehicles" Rosenbauer America, LLC 113021ͲRSD "Firefighting Apparatus and Fire Service Vehicles" The Sutphen Corporation 113021ͲSUT "Firefighting Apparatus and Fire Service Vehicles" Redwood Toxicology Laboratory, Inc. 011222ͲRTL "Lab Services and Testing with Related Products and Supplies" Sterling Healthcare Opco, dba Cordant Health
Solutions 011222ͲCDT "Lab Services and Testing with Related Products and Supplies"

CONTRACT EXTENSIONS
Supplier Name Contract Number Solicitation Title
HiͲVac Corporation 122017ͲHVC
"Sewer Vacuum, HydroͲExcavation, and Street Sweeper Equipment with Related Accessories and Supplies"
NiteHawk Sweepers, LLC 122017ͲNHK
"Sewer Vacuum, HydroͲExcavation, and Street Sweeper Equipment with Related Accessories and Supplies"
Schwarze Industries, Inc. 122017ͲSWZ
"Sewer Vacuum, HydroͲExcavation, and Street Sweeper Equipment with Related Accessories and Supplies"
AstroTurf Corporation 060518ͲAST
"Athletic Surfacing with Related Materials, Supplies, Installation and Services"
Shaw Sports Turf 060518ͲSII
"Athletic Surfacing with Related Materials, Supplies, Installation and Services"
NEW ezIQC CONTRACTS
Company Name Contract Number StateͲRegionͲType of Work Staples Construction CAͲR1ͲGB01Ͳ123021ͲSTA CaliforniaͲRegion 1ͲGeneral Building Mesa Energy Systems, Inc. dba EMCOR Services CAͲR1ͲHVAC01Ͳ123021ͲES CaliforniaͲRegion 1ͲHVAC/Mechanical ACCO Engineered Systems, Inc. CAͲR2ͲHVAC01Ͳ123021ͲAES CaliforniaͲRegion 2ͲHVAC/Mechanical T&S Intermodal Maintenance, Inc. DBA T&S West CAͲR3ͲE01Ͳ123021ͲTSW CaliforniaͲRegion 3ͲElectrical ABM Industries. Inc. CAͲR3ͲE02Ͳ123021ͲABM CaliforniaͲRegion 3ͲElectrical T&S Intermodal Maintenance, Inc. DBA T&S West CAͲR3ͲGB01Ͳ123021ͲTSW CaliforniaͲRegion 3ͲGeneral Building North Star Construction and Engineering, Inc. CAͲR3ͲGB02Ͳ123021ͲNSC CaliforniaͲRegion 3ͲGeneral Building North Star Construction and Engineering, Inc. CAͲR3ͲGS01Ͳ123021ͲNSC CaliforniaͲRegion 3ͲGeotechnical Stabilization ABM Industries. Inc. CAͲR3ͲHVAC01Ͳ123021ͲABM CaliforniaͲRegion 3ͲHVAC/Mechanical ACCO Engineered Systems, Inc. CAͲR3ͲHVAC02Ͳ123021ͲAES CaliforniaͲRegion 3ͲHVAC/Mechanical T&S Intermodal Maintenance, Inc. DBA T&S West CAͲR3ͲPAV01Ͳ123021ͲTSW CaliforniaͲRegion 3ͲPaving North Star Construction and Engineering, Inc. CAͲR3ͲPAV02Ͳ123021ͲNSC CaliforniaͲRegion 3ͲPaving Mark Scott Construction, Inc. CAͲR4ͲGB01Ͳ123021ͲMSC CaliforniaͲRegion 4ͲGeneral Building ABM Industries, Inc. CAͲR4ͲHVAC01Ͳ123021ͲABM CaliforniaͲRegion 4ͲHVAC/Mechanical T&S Intermodal Maintenance, Inc. DBA T&S West CAͲR5ͲE01Ͳ123021ͲTSW CaliforniaͲRegion 5ͲElectrical

CONSENT AGENDA ITEMS CONSENT AGENDA ITEMS
Wellness Engagement Program Solutions and Related Services Swimming Pool Renovation and Repair with Related Equipment, Supplies, and Services Requesting Board permission to ReͲSolicit the following categories:

Requesting Board permission to Solicit the following categories:

Indefinite Delivery Indefinite Quantity ConstructionͲMissouri 









 
 


EXHIBIT 1 557
APPENDIX A Continued
T&S Intermodal Maintenance, Inc. DBA T&S West CAͲR5ͲGB01Ͳ123021ͲTSW CaliforniaͲRegion 5ͲGeneral Building Newton Construction & Management, Inc. CAͲR5ͲGB02Ͳ123021ͲNCM CaliforniaͲRegion 5ͲGeneral Building Durham Construction Company, Inc. CAͲR5ͲGB03Ͳ123021ͲDCC CaliforniaͲRegion 5ͲGeneral Building Mark Scott Construction, Inc. CAͲR5ͲGB04Ͳ123021ͲMSC CaliforniaͲRegion 5ͲGeneral Building Mesa Energy Systems, Inc. dba EMCOR Services CAͲR5ͲHVAC01Ͳ123021ͲES CaliforniaͲRegion 5ͲHVAC/Mechanical ABM Industries, Inc. CAͲR5ͲHVAC02Ͳ123021ͲABM CaliforniaͲRegion 5ͲHVAC/Mechanical T&S Intermodal Maintenance, Inc. DBA T&S West CAͲR5ͲPAV01Ͳ123021ͲTSW CaliforniaͲRegion 5ͲPaving ABM Industries, Inc. CAͲR6ͲE01Ͳ123021ͲABM CaliforniaͲRegion 6ͲElectrical Newton Construction & Management, Inc. CAͲR6ͲGB01Ͳ123021ͲNCM CaliforniaͲRegion 6ͲGeneral Building Angeles Contractor, Inc. CAͲR6ͲGB02Ͳ123021ͲACI CaliforniaͲRegion 6ͲGeneral Building ABM Industries, Inc. CAͲR6ͲHVAC01Ͳ123021ͲABM CaliforniaͲRegion 6ͲHVAC/Mechanical ACCO Engineered Systems, Inc. CAͲR6ͲHVAC02Ͳ123021ͲAES CaliforniaͲRegion 6ͲHVAC/Mechanical Angeles Contractor, Inc. CAͲR6ͲPAV01Ͳ123021ͲACI CaliforniaͲRegion 6ͲPaving Newton Construction & Management, Inc. CAͲR7ͲE01Ͳ123021ͲNCM CaliforniaͲRegion 7ͲElectrical Newton Construction & Management, Inc. CAͲR7ͲGB01Ͳ123021ͲNCM CaliforniaͲRegion 7ͲGeneral Building MDJ Management, LLC CAͲR7ͲGB06Ͳ123021ͲMDJ CaliforniaͲRegion 7ͲGeneral Building ACCO Engineered Systems, Inc. CAͲR7ͲHVAC01Ͳ123021ͲAES CaliforniaͲRegion 7ͲHVAC/Mechanical Mesa Energy Systems, Inc. dba EMCOR Services CAͲR7ͲHVAC02Ͳ123021ͲES CaliforniaͲRegion 7ͲHVAC/Mechanical Horizons Construction Company Int'l, Inc. CAͲR7ͲPAV01Ͳ123021ͲHCC CaliforniaͲRegion 7ͲPaving J & H Engineering General Contractors, Inc. CAͲR7ͲPAV02Ͳ123021ͲJHE CaliforniaͲRegion 7ͲPaving ABM Industries, Inc. CAͲR8ͲE01Ͳ123021ͲABM CaliforniaͲRegion 8ͲElectrical Facility Solutions Group CAͲR8ͲE02Ͳ123021ͲFSG CaliforniaͲRegion 8ͲElectrical Pacific Lighting Mgt, Inc. CAͲR8ͲE03Ͳ123021ͲPLM CaliforniaͲRegion 8ͲElectrical Exbon Development, Inc. CAͲR8ͲE04Ͳ123021ͲEXB CaliforniaͲRegion 8ͲElectrical PUB Construction, Inc. CAͲR8ͲF01Ͳ123021ͲPUB CaliforniaͲRegion 8ͲFlooring California Coast Carpet & Flooring CAͲR8ͲF02Ͳ123021ͲCCF CaliforniaͲRegion 8ͲFlooring Angeles Contractor, Inc. CAͲR8ͲF03Ͳ123021ͲACI CaliforniaͲRegion 8ͲFlooring Horizons Construction Company Int'l, Inc. CAͲR8ͲGB01Ͳ123021ͲHCC CaliforniaͲRegion 8ͲGeneral Building Exbon Development, Inc. CAͲR8ͲGB02Ͳ123021ͲEXB CaliforniaͲRegion 8ͲGeneral Building PUB Construction, Inc. CAͲR8ͲGB03Ͳ123021ͲPUB CaliforniaͲRegion 8ͲGeneral Building Harry H. Joh Construction, Inc. CAͲR8ͲGB04Ͳ123021ͲHJC CaliforniaͲRegion 8ͲGeneral Building Vincor Construction, Inc. CAͲR8ͲGB05Ͳ123021ͲVCI CaliforniaͲRegion 8ͲGeneral Building Angeles Contractor, Inc. CAͲR8ͲGB06Ͳ123021ͲACI CaliforniaͲRegion 8ͲGeneral Building Mackone Development, Inc. CAͲR8ͲGB07Ͳ123021ͲMDI CaliforniaͲRegion 8ͲGeneral Building GoodͲMen Roofing & Construction, Inc. CAͲR8ͲGB08Ͳ123021ͲGMR CaliforniaͲRegion 8ͲGeneral Building MDJ Management, LLC CAͲR8ͲGB13Ͳ123021ͲMDJ CaliforniaͲRegion 8ͲGeneral Building ABM Industries, Inc. CAͲR8ͲHVAC01Ͳ123021ͲABM CaliforniaͲRegion 8ͲHVAC/Mechanical ACCO Engineered Systems, Inc. CAͲR8ͲHVAC02Ͳ123021ͲAES CaliforniaͲRegion 8ͲHVAC/Mechanical Exbon Development, Inc. CAͲR8ͲHVAC03Ͳ123021ͲEXB CaliforniaͲRegion 8ͲHVAC/Mechanical Harry H. Joh Construction, Inc. CAͲR8ͲHVAC04Ͳ123021ͲHJC CaliforniaͲRegion 8ͲHVAC/Mechanical PUB Construction, Inc. CAͲR8ͲP01Ͳ123021ͲPUB CaliforniaͲRegion 8ͲPainting Harry H. Joh Construction, Inc. CAͲR8ͲP02Ͳ123021ͲHJC CaliforniaͲRegion 8ͲPainting Angeles Contractor, Inc. CAͲR8ͲP03Ͳ123021ͲACI CaliforniaͲRegion 8ͲPainting Mackone Development, Inc. CAͲR8ͲP04Ͳ123021ͲMDI CaliforniaͲRegion 8ͲPainting Horizons Construction Company Int'l, Inc. CAͲR8ͲPAV01Ͳ123021ͲHCC CaliforniaͲRegion 8ͲPaving Angeles Contractor, Inc. CAͲR8ͲPAV02Ͳ123021ͲACI CaliforniaͲRegion 8ͲPaving Mackone Development, Inc. CAͲR8ͲPAV03Ͳ123021ͲMDI CaliforniaͲRegion 8ͲPaving Bitech Construction Co., Inc. CAͲR8ͲPAV04Ͳ123021ͲBIT CaliforniaͲRegion 8ͲPaving ACCO Engineered Systems, Inc. CAͲR8ͲPLUM01Ͳ123021ͲAES CaliforniaͲRegion 8ͲPlumbing Oscalibur Plumbing, Inc. CAͲR8ͲPLUM02Ͳ123021ͲOPI CaliforniaͲRegion 8ͲPlumbing Angeles Contractor, Inc. CAͲR8ͲRW01Ͳ123021ͲACI CaliforniaͲRegion 8ͲRoofing/Waterproofing Exbon Development, Inc. CAͲR8ͲRW02Ͳ123021ͲEXB CaliforniaͲRegion 8ͲRoofing/Waterproofing GoodͲMen Roofing & Construction, Inc. CAͲR8ͲRW03Ͳ123021ͲGMR CaliforniaͲRegion 8ͲRoofing/Waterproofing ACCO Engineered Systems, Inc. CAͲR8ͲSS01Ͳ123021ͲAES CaliforniaͲRegion 8ͲSanitation Systems ABM Industries, Inc. CAͲR9ͲE01Ͳ123021ͲABM CaliforniaͲRegion 9ͲElectrical Pacific Lighting Mgt, Inc. CAͲR9ͲE02Ͳ123021ͲPLM CaliforniaͲRegion 9ͲElectrical Horizons Construction Company Int'l, Inc. CAͲR9ͲGB01Ͳ123021ͲHCC CaliforniaͲRegion 9ͲGeneral Building PUB Construction, Inc. CAͲR9ͲGB02Ͳ123021ͲPUB CaliforniaͲRegion 9ͲGeneral Building Harry H. Joh Construction, Inc. CAͲR9ͲGB03Ͳ123021ͲHJC CaliforniaͲRegion 9ͲGeneral Building Pacific Building Group CAͲR9ͲGB04Ͳ123021ͲPBG CaliforniaͲRegion 9ͲGeneral Building Vincor Construction, Inc. CAͲR9ͲGB05Ͳ123021ͲVCI CaliforniaͲRegion 9ͲGeneral Building GoodͲMen Roofing & Construction, Inc. CAͲR9ͲGB06Ͳ123021ͲGMR CaliforniaͲRegion 9ͲGeneral Building All Source Coatings, Inc. CAͲR9ͲGB08Ͳ123021ͲASC CaliforniaͲRegion 9ͲGeneral Building GeoStabilization International, LLC CAͲR9ͲGS01Ͳ123021ͲGSI CaliforniaͲRegion 9ͲGeotechnical Stabilization ABM Industries, Inc. CAͲR9ͲHVAC01Ͳ123021ͲABM CaliforniaͲRegion 9ͲHVAC/Mechanical 









 
 


EXHIBIT 1 558
APPENDIX A Continued
ACCO Engineered Systems, Inc. CAͲR9ͲHVAC02Ͳ123021ͲAES CaliforniaͲRegion 9ͲHVAC/Mechanical Harry H. Joh Construction, Inc. CAͲR9ͲHVAC03Ͳ123021ͲHJC CaliforniaͲRegion 9ͲHVAC/Mechanical Mesa Energy Systems, Inc. dba EMCOR Services CAͲR9ͲHVAC04Ͳ123021ͲES CaliforniaͲRegion 9ͲHVAC/Mechanical Horizons Construction Company Int'l, Inc. CAͲR9ͲPAV01Ͳ123021ͲHCC CaliforniaͲRegion 9ͲPaving ACCO Engineered Systems, Inc. CAͲR9ͲPLUM01Ͳ123021ͲAES CaliforniaͲRegion 9ͲPlumbing GoodͲMen Roofing & Construction, Inc. CAͲR9ͲRW01Ͳ123021ͲGMR CaliforniaͲRegion 9ͲRoofing/Waterproofing ezIQC RENEWALS
Company Name Contract Number
Amstar, Inc. TXͲPBͲGCͲ121819ͲAMS
CORE Construction Services of Texas, Inc. TXͲWTͲGCͲ121819ͲCCT TMG Contracting, LLC TXͲCTͲGCͲ121819ͲTCL
Sullivan Contracting Services TXͲCTͲGCͲ121819ͲSUL
Amstar, Inc. TXͲWTͲGCͲ121819ͲAMS
CORE Construction Services of Texas, Inc. TXͲPBͲGCͲ121819ͲCCT Amstar, Inc. TXͲCTͲGCͲ121819ͲAMS
F.H. Paschen, S.N. Nielsen & Associates, LLC TXͲPBͲGCͲ121819ͲFHP Tommy Klein Construction, Inc. TXͲPBͲGCͲ121819ͲTKL
Doyle Electric, LLC TXͲCTͲGCͲ121819ͲDEL
Veliz Company, LLC TXͲPBͲGCͲ121819ͲVCL
RoofConnect Logistics, Inc. TXͲCTͲRͲ121819ͲRCL
Platinum Roofing, Inc. TXͲCTͲRͲ121819ͲPLR
F.H. Paschen, S.N. Nielsen & Associates, LLC TXͲWTͲGCͲ121819ͲFHP JAMCO Ventures, LLC TXͲCTͲGCͲ121819ͲJAM
CORE Construction Services of Texas, Inc. TXͲCTͲGCͲ121819ͲCCT JAMCO Ventures, LLC TXͲCTͲFͲ121819ͲJAM
Veliz Company, LLC TXͲCTͲGCͲ121819ͲVCL
F.H. Paschen, S.N. Nielsen & Associates, LLC TXͲCTͲGCͲ121819ͲFHP Doyle Electric, LLC TXͲCTͲEͲ121819ͲDEL
Veliz Company, LLC TXͲWTͲGCͲ121819ͲVCL
Centennial Contractors Enterprises, Inc. TXͲCTͲGCͲ121819ͲCCE RoofConnect Logistics, Inc. TXͲWTͲRͲ121819ͲRCL
JAMCO Ventures, LLC TXͲCTͲWͲ121819ͲJAM
JAMCO Ventures, LLC TXͲCTͲRCͲ121819ͲJAM
JAMCO Ventures, LLC TXͲCTͲAPCͲ121819ͲJAM
JAMCO Ventures, LLC TXͲCTͲPͲ121819ͲJAM










 
 


EXHIBIT 1 559

COMMENT AND REVIEW
to the
REQUEST FOR PROPOSAL (RFP) #113021
Entitled
Firefighting Apparatus and Fire Service Vehicles
The following advertisement was placed October 12, 2021 in USA Today, in South Carolina’s The State, in The Oklahoman and on the Sourcewell website www.sourcewell-mn.gov, Sourcewell Procurement Portal https://proportal.sourcewell-mn.gov, Biddingo, Merx, The New York State Contract Reporter www.nyscr.ny.gov, PublicPurchase.com, and October 13, 2021 in Oregon’s Daily Journal of Commerce:

Sourcewell, a State of Minnesota local government unit and service cooperative, is requesting proposals for Firefighting Apparatus and Fire Service Vehicles to result in a contracting solution for use by its Participating Entities. Sourcewell Participating Entities include thousands of governmental, higher education, K-12 education, nonprofit, tribal government, and other public agencies located in the United States and Canada. A full copy of the Request for Proposals can be found on the Sourcewell Procurement Portal [https://proportal.sourcewell-mn.gov]. Only proposals submitted through the Sourcewell Procurement Portal will be considered. Proposals are due no later than November 30, 2021, at 4:30 p.m. Central Time, and late proposals will not be considered.

The solicitation process was conducted through the Sourcewell Procurement Portal. The following parties expressed interest in the solicitation by registering for this opportunity within the portal:
10-8 Emergency Vehicle Service Kovatch Mobile Equipment Corp. 11193422 Canada, INC. Kyrish Government Group
Acres Industries, Inc. Laszlo Corporation
Alexis Fire Equipment Company Marion Body Works, Inc.

Allied Restoration MAXIMETAL INC.

Blanchat Mfg., Inc. Metalfab, LTD
BME Fire Trucks, LLC MSA Safety Sales, LLC
Brindlee Mountain Fire Apparatus, LLC North America Fire Equipment Co., Inc.

CAMIONS CARL THIBAULT, INC. O'RIELLY CHEVROLET, INC.

Carrier Truck Centers Oshkosh Airport Products, LLC
CET Fire Pumps MFG P.L. Custom Body and Equipment Co., Inc.

Chemical Containers, Inc. PECS Electromechanical
Commercial Emergency Equipment Pierce Manufacturing (Oshkosh Corporation) Cooperative Services, LLC Rock River Industries, LLC















EXHIBIT 1 560
Sourcewell Page 2 of 5
Custom Fire Apparatus, Inc. Rosenbauer South Dakota, LLC D-Lux Screen Printing Sea Hawk
Danko Emergency Equipment Servco Pacific, Inc.

Dependable Truck & Tank, Limited Skeeter Brush Trucks, LLC Draeger Safety Canada, Ltd. Southern Fire Apparatus, LLC E-ONE, Inc. (REV Group, Inc.) Spartan Fire, LLC
Ed M. Feld Equipment Co., Inc. DBA Feld Fire Spencer Manufacturing, Inc.

EJ Metals, LLC SPI Health and Safety, Inc.

Ferrara Fire Apparatus, Inc. Stainless and Repair, Inc.

Fire & Safety Services, Ltd. Sub Aquatics, Inc.

FIRE AND MARINE, INC. Super Vacuum Manufacturing CO., Inc.

FireStopper USA MD System One Manufacturing, Inc.

First Priority Emergency Vehicles, Inc. The Sutphen Corporation Fisher Tech Services, LLC Tipton Ford
Fort Garry FIre Trucks, Ltd. Toyne, Inc.

Four Guys Stainless Tank & Equipment, Inc. Ty Parker & Son, Inc.

Fouts Brothers, Inc. Unifire, Inc.

Hi-Tech Emergency Vehicle Service, Inc. US Fire Equipment, LLC HME, Incorporated Ward Apparatus, LLC
Holland Pump Company Warren Anderson Ford dba Fritts Ford HUB Fire Engines & Equipment, Ltd. Watts Manufacturing, LLC HydeInfoTech WBM GP., INC.

Intercontinental Truck Body, Ltd. Westvac Industrial, Ltd.

All Proposals remained sealed within the Sourcewell Procurement Portal until the scheduled due date and time. Proposals were electronically opened, and the list of all Proposers was made publicly available on the Sourcewell Procurement Portal, on November 30, 2021, at 4:32:09 pm CT. Proposals were received from the following:

Acres Industries, Inc.

Alexis Fire Equipment Company
BME Fire Trucks, LLC
Brindlee Mountain Fire Apparatus, LLC
CAMIONS CARL THIBAULT, INC.

CET Fire Pumps MFG
Chemical Containers, Inc.

Custom Fire Apparatus, Inc.

Dependable Truck & Tank, Limited
EJ Metals, LLC
FireStopper USA MD
Fort Garry Fire Trucks, Ltd.

Fouts Brothers, Inc.

Hi-Tech Emergency Vehicle Service, Inc.

HME, Inc.

HUB Fire Engines & Equipment, Ltd.

Laszlo Corporation
Marion Body Works, Inc.















EXHIBIT 1 561
Sourcewell Page 3 of 5
MAXIMETAL INC.

Metalfab, LTD
Oshkosh Corporation (Pierce Manufacturing)
P.L. Custom Body and Equipment Co., Inc.

REV Group, Inc. (E-One, Inc.)
Rock River Industries, LLC
Rosenbauer America, LLC (Rosenbauer South Dakota, LLC)
Skeeter Brush Trucks, LLC
Spencer Manufacturing, Inc.

Super Vacuum Manufacturing Co., Inc.

The Sutphen Corporation
Toyne, Inc.

Ty Parker & Son, Inc.

US Fire Equipment, LLC
Ward Apparatus, LLC
Proposals were reviewed by the Proposal Evaluation Committee:

Kim Austin, MBA, CPPB, Procurement Lead Analyst
Stephanie Haataja, CPIM, Procurement Analyst
Craig West, Procurement Analyst
Tom Sharbonno, Procurement Analyst
The findings of the Proposal Evaluation Committee are summarized as follows:

The Proposal Evaluation Committee applied the Sourcewell RFP evaluation criteria and determined that all proposal responses met the scope and mandatory submittal requirements and were evaluated.

Custom Fire Apparatus, Inc., provides a wide variety of fire service vehicles including initial attack/wildland, pumpers, rescue, and mobile water supply/pumper tender firefighting apparatus. They will provide sales and service in the United States and Canada. Their price list includes many common options when customizing base model vehicles. Custom Fire Apparatus, Inc. is offering Sourcewell participating entities a solid discount off list pricing.

HME, Inc., manufactures aerials, pumpers, tankers, and wildland firefighting apparatus. Their sales and dealer network are available to Sourcewell participating entities throughout the United States and Canada. Dealers are available for 24-hour emergency service and mobile repair. HME is offering a considerable discount off MSRP. Prepay and quantity discounts are also available.

MAXIMETAL Inc. offers a product line that includes pumpers, tankers, rescues, command vehicles, and wildland firefighting apparatus. Their sales representatives and dealer network can provide sales and service to all Sourcewell participating entities in the United States and Canada. They are able to offer 24–48-hour critical parts delivery to their customers. MAXIMETAL is offering a competitive discount off list pricing and an additional volume discount for two or more identical units on a single purchase order.

Oshkosh Corporation is offering a wide variety of products including custom and commercial pumper products, aerial products, and emergency response vehicles. They will serve Sourcewell participating entities in the United States and Canada through their regional sales and service model. Oshkosh Corporation is providing a combination 














EXHIBIT 1 562
Sourcewell Page 4 of 5
of line item, percentage, multi-unit, pre-pay and progress payment discounts (as applicable) on their fire apparatus offering.

P.L. Custom Body and Equipment Co., Inc., manufactures custom extreme duty rescue trucks, command centers, hazmat, and other specialty vehicles. Numerous chassis platforms are available to meet varying needs and specifications. They have a sizeable sales force and dealer network throughout the United States. P.L. Custom is a woman-owned entity (WMBE). They proposed a strong discount to Sourcewell participating entities.

REV Group, Inc., is a manufacturer and service provider of fire apparatus that includes pumpers, rescues, tankers, aerials, hazmat, command vehicles, ARFF units, Spartan Chassis, and wildland fire service vehicles. Their sale representatives and robust dealer network offers sales and service to all Sourcewell participating entities in the United States and Canada. They offer leasing, trade-ins, pre-pay discounts and multiple unit discounts. REV Group offers a sizeable discount off their list pricing.

Rock River Industries, LLC, is offering a full line of all-poly tankers, pumpers, tactical tenders, brush trucks, and quick attack vehicles under the Midwest Fire brand name. Midwest Fire has a sales staff able to serve participating entities in the United States and Canada through a direct sales strategy. They provide no cost training on new apparatus during the delivery process and equipment pricing reflects a considerable discount off list.

Rosenbauer America LLC is a manufacturer of aerials, pumpers, tankers, rescue vehicles, wildland, ARFF, and a fully electric fire truck. Rosenbauer also manufacturers their own custom chassis, the Commander, Warrior and Avenger. Their sales force, consisting of 32 dealers in the United States and Canada, is prepared to serve Sourcewell participating entities. Rosenbauer is providing competitive discounts from MSRP.

The Sutphen Corporation is a manufacturer of custom fire apparatus. Their product line includes a variety of specialty fire apparatus including industrial pumpers, heavy rescues, and hazmat units. Sutphen’s offering also includes aerial devices constructed solely of aluminum which reduces weight and improves handling. Their large dealer network spans the United States and Canada. Sutphen Corporation is offering participating entities a notable discount from MSRP.

For these reasons, the Sourcewell Proposal Evaluation Committee recommends award of Sourcewell Contract #113021 to:

Custom Fire Apparatus, Inc. #113021-CSM
HME, Inc. #113021-HME
MAXIMETAL Inc. #113021-MAX
Oshkosh Corporation #113021-PMI
P.L. Custom Body and Equipment Co., Inc. #113021-PLC
Rev Group (E-One, Inc.) #113021-EOI
Rock River Industries #113021-RCK
Rosenbauer America LLC #113021-RSD
The Sutphen Corporation #113021-SUT
The preceding recommendations were approved on February 7, 2022. 














EXHIBIT 1 563
Sourcewell Page 5 of 5
________________________________
Kim Austin, MBA, CPPB, Procurement Lead Analyst
________________________________
Stephanie Haataja, CPIM, Procurement Analyst
________________________________
Craig West, Procurement Analyst
_________________________________
Tom Sharbonno, Procurement Analyst

STATEMENT OF COMPLIANCE
As Chief Procurement Officer for Sourcewell, I have reviewed the recommendation of the Evaluation Committee and the accompanying support materials documenting the process followed for RFP #113021 for Firefighting Apparatus and Fire Service Vehicles.

The committee accepted, deemed responsive, evaluated, and recommended proposals for award. Under authority granted to the Chief Procurement Officer in Sourcewell’s bylaws, the recommendations set forth above are approved.

I hereby certify:

1. Sourcewell is a government agency, created and authorized by Minnesota law to provide cooperative procurement contracts.

2. The procurement process and resulting contracts have been awarded in compliance with the laws of the State of Minnesota (Minnesota Statutes Chapter 471 and Minnesota Statutes Section 123A.21), and in conformity to Sourcewell’s Procurement Policy.

Jeremy Schwartz, CSSBB, CPPO
Chief Procurement Officer















EXHIBIT 1 564
113021-OKC
Rev. 3/2021 1
Solicitation Number: RFP #113021

CONTRACT
This Contract is between Sourcewell, 202 12th Street Northeast, P.O. Box 219, Staples, MN 56479 (Sourcewell) and Oshkosh Corporation, 1917 Four Wheel Dr., Oshkosh, WI 54902 (Supplier), and Supplier’s consolidated subsidiaries as defined in the Proposal.

Sourcewell is a State of Minnesota local government unit and service cooperative created under the laws of the State of Minnesota (Minnesota Statutes Section 123A.21) that offers cooperative procurement solutions to government entities. Participation is open to eligible federal, state/province, and municipal governmental entities, higher education, K-12 education, nonprofit, tribal government, and other public entities located in the United States and Canada.

Sourcewell issued a public solicitation for Firefighting Apparatus and Fire Service Vehicles from which Supplier was awarded a contract.

Supplier desires to contract with Sourcewell to provide equipment, products, or services to Sourcewell and the entities that access Sourcewell’s cooperative purchasing contracts (Participating Entities).

1. TERM OF CONTRACT
A. EFFECTIVE DATE. This Contract is effective upon the date of the final signature below.

B. EXPIRATION DATE AND EXTENSION. This Contract expires February 10, 2026, unless it is cancelled sooner pursuant to Article 22. This Contract may be extended one additional year upon the request of Sourcewell and written agreement by Supplier.

C. SURVIVAL OF TERMS. Notwithstanding any expiration or termination of this Contract, all payment obligations incurred prior to expiration or termination will survive, as will the following: Articles 11 through 14 survive the expiration or cancellation of this Contract. All other rights will cease upon expiration or termination of this Contract.

2. EQUIPMENT, PRODUCTS, OR SERVICES
A. EQUIPMENT, PRODUCTS, OR SERVICES. Supplier will provide the Equipment, Products, or Services as stated in its Proposal submitted under the Solicitation Number listed above. 













 

EXHIBIT 1 565
113021-OKC
Rev. 3/2021 2
Supplier’s Equipment, Products, or Services Proposal (Proposal) is attached and incorporated into this Contract.

All Equipment and Products provided under this Contract must be new and the current model.

Supplier may offer close-out, refurbished, or remounted Equipment or Products if they are clearly indicated in Supplier’s product and pricing list. Unless agreed to by the Participating Entities in advance, Equipment or Products must be delivered as operational to the Participating Entity’s site.

This Contract offers an indefinite quantity of sales, and while substantial volume is anticipated, sales and sales volume are not guaranteed.

B. WARRANTY. Supplier warrants that all Equipment, Products, and Services furnished are free from liens and encumbrances, and are free from defects in design, materials, and workmanship.

In addition, Supplier warrants the Equipment, Products, and Services are suitable for and will perform in accordance with the ordinary use for which they are intended. Supplier’s dealers and distributors must agree to assist the Participating Entity in reaching a resolution in any dispute over warranty terms with the manufacturer. Any manufacturer’s warranty that extends beyond the expiration of the Supplier’s warranty will be passed on to the Participating Entity.

C. DEALERS, DISTRIBUTORS, AND/OR RESELLERS. Upon Contract execution and throughout the Contract term, Supplier must provide to Sourcewell a current means to validate or authenticate Supplier’s authorized dealers, distributors, or resellers relative to the Equipment, Products, and Services offered under this Contract, which will be incorporated into this Contract by reference. It is the Supplier’s responsibility to ensure Sourcewell receives the most current information.

3. PRICING
All Equipment, Products, or Services under this Contract will be priced at or below the price stated in Supplier’s Proposal.

When providing pricing quotes to Participating Entities, all pricing quoted must reflect a Participating Entity’s total cost of acquisition. This means that the quoted cost is for delivered Equipment, Products, and Services that are operational for their intended purpose, and includes all costs to the Participating Entity’s requested delivery location.

Regardless of the payment method chosen by the Participating Entity, the total cost associated with any purchase option of the Equipment, Products, or Services must always be disclosed in the pricing quote to the applicable Participating Entity at the time of purchase.

A. SHIPPING AND SHIPPING COSTS. All delivered Equipment and Products must be properly packaged. Damaged Equipment and Products may be rejected. If the damage is not readily 













 

EXHIBIT 1 566
113021-OKC
Rev. 3/2021 3
apparent at the time of delivery, Supplier must permit the Equipment and Products to be returned within a reasonable time at no cost to Sourcewell or its Participating Entities.

Participating Entities reserve the right to inspect the Equipment and Products at a reasonable time after delivery where circumstances or conditions prevent effective inspection of the Equipment and Products at the time of delivery. In the event of the delivery of nonconforming Equipment and Products, the Participating Entity will notify the Supplier as soon as possible and the Supplier will replace nonconforming Equipment and Products with conforming Equipment and Products that are acceptable to the Participating Entity.

Supplier must arrange for and pay for the return shipment on Equipment and Products that arrive in a defective or inoperable condition.

Sourcewell may declare the Supplier in breach of this Contract if the Supplier intentionally delivers substandard or inferior Equipment or Products.

B. SALES TAX. Each Participating Entity is responsible for supplying the Supplier with valid taxexemption certification(s). When ordering, a Participating Entity must indicate if it is a taxexempt entity.

C. HOT LIST PRICING. At any time during this Contract, Supplier may offer a specific selection of Equipment, Products, or Services at discounts greater than those listed in the Contract.

When Supplier determines it will offer Hot List Pricing, it must be submitted electronically to Sourcewell in a line-item format. Equipment, Products, or Services may be added or removed from the Hot List at any time through a Sourcewell Price and Product Change Form as defined in Article 4 below.

Hot List program and pricing may also be used to discount and liquidate close-out and discontinued Equipment and Products as long as those close-out and discontinued items are clearly identified as such. Current ordering process and administrative fees apply. Hot List Pricing must be published and made available to all Participating Entities.

4. PRODUCT AND PRICING CHANGE REQUESTS
Supplier may request Equipment, Product, or Service changes, additions, or deletions at any time. All requests must be made in writing by submitting a signed Sourcewell Price and Product Change Request Form to the assigned Sourcewell Supplier Development Administrator. This approved form is available from the assigned Sourcewell Supplier Development Administrator.

At a minimum, the request must:
x Identify the applicable Sourcewell contract number;
x Clearly specify the requested change;
x Provide sufficient detail to justify the requested change; 













 

EXHIBIT 1 567
113021-OKC
Rev. 3/2021 4
x Individually list all Equipment, Products, or Services affected by the requested change, along with the requested change (e.g., addition, deletion, price change); and x Include a complete restatement of pricing documentation in Microsoft Excel with the effective date of the modified pricing, or product addition or deletion. The new pricing restatement must include all Equipment, Products, and Services offered, even for those items where pricing remains unchanged.

A fully executed Sourcewell Price and Product Change Request Form will become an amendment to this Contract and will be incorporated by reference.

5. PARTICIPATION, CONTRACT ACCESS, AND PARTICIPATING ENTITY REQUIREMENTS

A. PARTICIPATION. Sourcewell’s cooperative contracts are available and open to public and nonprofit entities across the United States and Canada; such as federal, state/province, municipal, K-12 and higher education, tribal government, and other public entities.

The benefits of this Contract should be available to all Participating Entities that can legally access the Equipment, Products, or Services under this Contract. A Participating Entity’s authority to access this Contract is determined through its cooperative purchasing, interlocal, or joint powers laws. Any entity accessing benefits of this Contract will be considered a Service Member of Sourcewell during such time of access. Supplier understands that a Participating Entity’s use of this Contract is at the Participating Entity’s sole convenience and Participating Entities reserve the right to obtain like Equipment, Products, or Services from any other source.

Supplier is responsible for familiarizing its sales and service forces with Sourcewell contract use eligibility requirements and documentation and will encourage potential participating entities to join Sourcewell. Sourcewell reserves the right to add and remove Participating Entities to its roster during the term of this Contract.

B. PUBLIC FACILITIES. Supplier’s employees may be required to perform work at governmentowned facilities, including schools. Supplier’s employees and agents must conduct themselves in a professional manner while on the premises, and in accordance with Participating Entity policies and procedures, and all applicable laws.

6. PARTICIPATING ENTITY USE AND PURCHASING
A. ORDERS AND PAYMENT. To access the contracted Equipment, Products, or Services under this Contract, a Participating Entity must clearly indicate to Supplier that it intends to access this Contract; however, order flow and procedure will be developed jointly between Sourcewell and Supplier. Typically, a Participating Entity will issue an order directly to Supplier or its authorized subsidiary, distributor, dealer, or reseller. If a Participating Entity issues a purchase order, it may use its own forms, but the purchase order should clearly note the applicable Sourcewell 













 

EXHIBIT 1 568
113021-OKC
Rev. 3/2021 5
contract number. All Participating Entity orders under this Contract must be issued prior to expiration or cancellation of this Contract; however, Supplier performance, Participating Entity payment obligations, and any applicable warranty periods or other Supplier or Participating Entity obligations may extend beyond the term of this Contract.

Supplier’s acceptable forms of payment are included in its attached Proposal. Participating Entities will be solely responsible for payment and Sourcewell will have no liability for any unpaid invoice of any Participating Entity.

B. ADDITIONAL TERMS AND CONDITIONS/PARTICIPATING ADDENDUM. Additional terms and conditions to a purchase order, or other required transaction documentation, may be negotiated between a Participating Entity and Supplier, such as job or industry-specific requirements, legal requirements (e.g., affirmative action or immigration status requirements), or specific local policy requirements. Some Participating Entities may require the use of a Participating Addendum; the terms of which will be negotiated directly between the Participating Entity and the Supplier. Any negotiated additional terms and conditions must never be less favorable to the Participating Entity than what is contained in this Contract.

C. SPECIALIZED SERVICE REQUIREMENTS. In the event that the Participating Entity requires service or specialized performance requirements not addressed in this Contract (such as ecommerce specifications, specialized delivery requirements, or other specifications and requirements), the Participating Entity and the Supplier may enter into a separate, standalone agreement, apart from this Contract. Sourcewell, including its agents and employees, will not be made a party to a claim for breach of such agreement.

D. TERMINATION OF ORDERS. Participating Entities may terminate an order, in whole or in part, immediately upon notice to Supplier in the event of any of the following events:

1. The Participating Entity fails to receive funding or appropriation from its governing body at levels sufficient to pay for the equipment, products, or services to be purchased; or

2. Federal, state, or provincial laws or regulations prohibit the purchase or change the Participating Entity’s requirements.

E. GOVERNING LAW AND VENUE. The governing law and venue for any action related to a Participating Entity’s order will be determined by the Participating Entity making the purchase.

7. CUSTOMER SERVICE
A. PRIMARY ACCOUNT REPRESENTATIVE. Supplier will assign an Account Representative to Sourcewell for this Contract and must provide prompt notice to Sourcewell if that person is changed. The Account Representative will be responsible for:















 

EXHIBIT 1 569
113021-OKC
Rev. 3/2021 6
x Maintenance and management of this Contract;
x Timely response to all Sourcewell and Participating Entity inquiries; and x Business reviews to Sourcewell and Participating Entities, if applicable.

B. BUSINESS REVIEWS. Supplier must perform a minimum of one business review with Sourcewell per contract year. The business review will cover sales to Participating Entities, pricing and contract terms, administrative fees, sales data reports, supply issues, customer issues, and any other necessary information.

8. REPORT ON CONTRACT SALES ACTIVITY AND ADMINISTRATIVE FEE PAYMENT A. CONTRACT SALES ACTIVITY REPORT. Each calendar quarter, Supplier must provide a contract sales activity report (Report) to the Sourcewell Supplier Development Administrator assigned to this Contract. Reports are due no later than 45 days after the end of each calendar quarter. A Report must be provided regardless of the number or amount of sales during that quarter (i.e., if there are no sales, Supplier must submit a report indicating no sales were made).

The Report must contain the following fields:
x Participating Entity Name (e.g., City of Staples Highway Department); x Participating Entity Physical Street Address;
x Participating Entity City;
x Participating Entity State/Province;
x Participating Entity Zip/Postal Code;
x Participating Entity Contact Name;
x Participating Entity Contact Email Address;
x Participating Entity Contact Telephone Number;
x Sourcewell Assigned Entity/Participating Entity Number; x Item Purchased Description;
x Item Purchased Price;
x Sourcewell Administrative Fee Applied; and
x Date Purchase was invoiced/sale was recognized as revenue by Supplier.

B. ADMINISTRATIVE FEE. In consideration for the support and services provided by Sourcewell, the Supplier will pay an administrative fee to Sourcewell on all Equipment, Products, and Services provided to Participating Entities. The Administrative Fee must be included in, and not added to, the pricing. Supplier may not charge Participating Entities more than the contracted price to offset the Administrative Fee.

The Supplier will submit payment to Sourcewell for the percentage of administrative fee stated in the Proposal multiplied by the total sales of all Equipment, Products, and Services purchased 













 

EXHIBIT 1 570
113021-OKC
Rev. 3/2021 7
by Participating Entities under this Contract during each calendar quarter. Payments should note the Supplier’s name and Sourcewell-assigned contract number in the memo; and must be mailed to the address above “Attn: Accounts Receivable” or remitted electronically to Sourcewell’s banking institution per Sourcewell’s Finance department instructions. Payments must be received no later than 45 calendar days after the end of each calendar quarter.

Supplier agrees to cooperate with Sourcewell in auditing transactions under this Contract to ensure that the administrative fee is paid on all items purchased under this Contract.

In the event the Supplier is delinquent in any undisputed administrative fees, Sourcewell reserves the right to cancel this Contract and reject any proposal submitted by the Supplier in any subsequent solicitation. In the event this Contract is cancelled by either party prior to the Contract’s expiration date, the administrative fee payment will be due no more than 30 days from the cancellation date.

9. AUTHORIZED REPRESENTATIVE
Sourcewell's Authorized Representative is its Chief Procurement Officer.

Supplier’s Authorized Representative is the person named in the Supplier’s Proposal. If Supplier’s Authorized Representative changes at any time during this Contract, Supplier must promptly notify Sourcewell in writing.

10. AUDIT, ASSIGNMENT, AMENDMENTS, WAIVER, AND CONTRACT COMPLETE A. AUDIT. Pursuant to Minnesota Statutes Section 16C.05, subdivision 5, the books, records, documents, and accounting procedures and practices relevant to this Agreement are subject to examination by Sourcewell or the Minnesota State Auditor for a minimum of six years from the end of this Contract. This clause extends to Participating Entities as it relates to business conducted by that Participating Entity under this Contract.

B. ASSIGNMENT. Neither party may assign or otherwise transfer its rights or obligations under this Contract without the prior written consent of the other party and a fully executed assignment agreement. Such consent will not be unreasonably withheld. Any prohibited assignment will be invalid.

C. AMENDMENTS. Any amendment to this Contract must be in writing and will not be effective until it has been duly executed by the parties.

D. WAIVER. Failure by either party to take action or assert any right under this Contract will not be deemed a waiver of such right in the event of the continuation or repetition of the circumstances giving rise to such right. Any such waiver must be in writing and signed by the parties.














 

EXHIBIT 1 571
113021-OKC
Rev. 3/2021 8
E. CONTRACT COMPLETE. This Contract represents the complete agreement between the parties. No other understanding regarding this Contract, whether written or oral, may be used to bind either party.For any conflict between the attached Proposal and the terms set out in Articles 1-22 of this Contract, the terms of Articles 1-22 will govern.

F. RELATIONSHIP OF THE PARTIES. The relationship of the parties is one of independent contractors, each free to exercise judgment and discretion with regard to the conduct of their respective businesses. This Contract does not create a partnership, joint venture, or any other relationship such as master-servant, or principal-agent.

11. INDEMNITY AND HOLD HARMLESS

Supplier must indemnify, defend, save, and hold Sourcewell and its Participating Entities, including their agents and employees, harmless from any claims or causes of action, including attorneys’ fees incurred by Sourcewell or its Participating Entities, arising out of any act or omission in the performance of this Contract by the Supplier or its agents or employees; this indemnification includes injury or death to person(s) or property alleged to have been caused by some defect in the Equipment, Products, or Services under this Contract to the extent the Equipment, Product, or Service has been used according to its specifications. Sourcewell’s responsibility will be governed by the State of Minnesota’s Tort Liability Act (Minnesota Statutes Chapter 466) and other applicable law.

12. GOVERNMENT DATA PRACTICES
Supplier and Sourcewell must comply with the Minnesota Government Data Practices Act, Minnesota Statutes Chapter 13, as it applies to all data provided by or provided to Sourcewell under this Contract and as it applies to all data created, collected, received, stored, used, maintained, or disseminated by the Supplier under this Contract.

13. INTELLECTUAL PROPERTY, PUBLICITY, MARKETING, AND ENDORSEMENT A. INTELLECTUAL PROPERTY

1. Grant of License. During the term of this Contract:
a. Sourcewell grants to Supplier a royalty-free, worldwide, non-exclusive right and license to use thetrademark(s) provided to Supplier by Sourcewell in advertising and promotional materials for the purpose of marketing Sourcewell’s relationship with Supplier.
b. Supplier grants to Sourcewell a royalty-free, worldwide, non-exclusive right and license to use Supplier’s trademarks in advertising and promotional materials for the purpose of marketing Supplier’s relationship with Sourcewell.

2. Limited Right of Sublicense. The right and license granted herein includes a limited right of each party to grant sublicenses to their respective subsidiaries, distributors, dealers, 













 

EXHIBIT 1 572
113021-OKC
Rev. 3/2021 9
resellers, marketing representatives, and agents (collectively “Permitted Sublicensees”) in advertising and promotional materials for the purpose of marketing the Parties’ relationship to Participating Entities. Any sublicense granted will be subject to the terms and conditions of this Article. Each party will be responsible for any breach of this Article by any of their respective sublicensees.

3. Use; Quality Control.
a. Neither party may alter the other party’s trademarks from the form provided and must comply with removal requests as to specific uses of its trademarks or logos.
b. Each party agrees to use, and to cause its Permitted Sublicensees to use, the other party’s trademarks only in good faith and in a dignified manner consistent with such party’s use of the trademarks. Upon written notice to the breaching party, the breaching party has 30 days of the date of the written notice to cure the breach or the license will be terminated.

4. As applicable, Supplier agrees to indemnify and hold harmless Sourcewell and its Participating Entities against any and all suits, claims, judgments, and costs instituted or recovered against Sourcewell or Participating Entities by any person on account of the use of any Equipment or Products by Sourcewell or its Participating Entities supplied by Supplier in violation of applicable patent or copyright laws.

5. Termination. Upon the termination of this Contract for any reason, each party, including Permitted Sublicensees, will have 30 days to remove all Trademarks from signage, websites, and the like bearing the other party’s name or logo (excepting Sourcewell’s pre-printed catalog of suppliers which may be used until the next printing). Supplier must return all marketing and promotional materials, including signage, provided by Sourcewell, or dispose of it according to Sourcewell’s written directions.

B. PUBLICITY. Any publicity regarding the subject matter of this Contract must not be released without prior written approval from the Authorized Representatives. Publicity includes notices, informational pamphlets, press releases, research, reports, signs, and similar public notices prepared by or for the Supplier individually or jointly with others, or any subcontractors, with respect to the program, publications, or services provided resulting from this Contract.

C. MARKETING. Any direct advertising, marketing, or offers with Participating Entities must be approved by Sourcewell. Send all approval requests to the Sourcewell Supplier Development Administrator assigned to this Contract.

D. ENDORSEMENT. The Supplier must not claim that Sourcewell endorses its Equipment, Products, or Services.














 

EXHIBIT 1 573
113021-OKC
Rev. 3/2021 10

14. GOVERNING LAW, JURISDICTION, AND VENUE
The substantive and procedural laws of the State of Minnesota will govern this Contract. Venue for all legal proceedings arising out of this Contract, or its breach, must be in the appropriate state court in Todd County, Minnesota or federal court in Fergus Falls, Minnesota.

15. FORCE MAJEURE
Neither party to this Contract will be held responsible for delay or default caused by acts of God or other conditions that are beyond that party’s reasonable control. A party defaulting under this provision must provide the other party prompt written notice of the default.

16. SEVERABILITY
If any provision of this Contract is found by a court of competent jurisdiction to be illegal, unenforceable, or void then both parties will be relieved from all obligations arising from that provision. If the remainder of this Contract is capable of being performed, it will not be affected by such determination or finding and must be fully performed.

17. PERFORMANCE, DEFAULT, AND REMEDIES
A. PERFORMANCE. During the term of this Contract, the parties will monitor performance and address unresolved contract issues as follows:

1. Notification. The parties must promptly notify each other of any known dispute and work in good faith to resolve such dispute within a reasonable period of time. If necessary, Sourcewell and the Supplier will jointly develop a short briefing document that describes the issue(s), relevant impact, and positions of both parties.

2. Escalation. If parties are unable to resolve the issue in a timely manner, as specified above, either Sourcewell or Supplier may escalate the resolution of the issue to a higher level of management. The Supplier will have 30 calendar days to cure an outstanding issue.

3. Performance while Dispute is Pending. Notwithstanding the existence of a dispute, the Supplier must continue without delay to carry out all of its responsibilities under the Contract that are not affected by the dispute. If the Supplier fails to continue without delay to perform its responsibilities under the Contract, in the accomplishment of all undisputed work, the Supplier will bear any additional costs incurred by Sourcewell and/or its Participating Entities as a result of such failure to proceed.

B. DEFAULT AND REMEDIES. Either of the following constitutes cause to declare this Contract, or any Participating Entity order under this Contract, in default:

1. Nonperformance of contractual requirements, or

2. A material breach of any term or condition of this Contract. 













 

EXHIBIT 1 574
113021-OKC
Rev. 3/2021 11
The party claiming default must provide written notice of the default, with 30 calendar days to cure the default. Time allowed for cure will not diminish or eliminate any liability for liquidated or other damages. If the default remains after the opportunity for cure, the non-defaulting party may:
x Exercise any remedy provided by law or equity, or
x Terminate the Contract or any portion thereof, including any orders issued against the Contract.

18. INSURANCE

A. REQUIREMENTS. At its own expense, Supplier must maintain insurance policy(ies) in effect at all times during the performance of this Contract with insurance company(ies) licensed or authorized to do business in the State of Minnesota having an “AM BEST” rating of A- or better, with coverage and limits of insurance not less than the following:

1. Workers’ Compensation and Employer’s Liability.

Workers’ Compensation: As required by any applicable law or regulation.

Employer's Liability Insurance: must be provided in amounts not less than listed below:

Minimum limits:
$500,000 each accident for bodily injury by accident
$500,000 policy limit for bodily injury by disease
$500,000 each employee for bodily injury by disease

2. Commercial General Liability Insurance. Supplier will maintain insurance covering its operations, with coverage on an occurrence basis, and must be subject to terms no less broad than the Insurance Services Office (“ISO”) Commercial General Liability Form CG0001 (2001 or newer edition), or equivalent. At a minimum, coverage must include liability arising from premises, operations, bodily injury and property damage, independent contractors, products-completed operations including construction defect, contractual liability, blanket contractual liability, and personal injury and advertising injury. All required limits, terms and conditions of coverage must be maintained during the term of this Contract.

Minimum Limits:
$1,000,000 each occurrence Bodily Injury and Property Damage $1,000,000 Personal and Advertising Injury
$2,000,000 aggregate for Products-Completed operations
$2,000,000 general aggregate

3. Commercial Automobile Liability Insurance. During the term of this Contract, Supplier will maintain insurance covering all owned, hired, and non-owned automobiles in limits of liability not less than indicated below. The coverage must be subject to terms 













 

EXHIBIT 1 575
113021-OKC
Rev. 3/2021 12
no less broad than ISO Business Auto Coverage Form CA 0001 (2010 edition or newer), or equivalent.

Minimum Limits:
$1,000,000 each accident, combined single limit

4. Umbrella Insurance. During the term of this Contract, Supplier will maintain umbrella coverage over Employer’s Liability, Commercial General Liability, and Commercial Automobile.

Minimum Limits:
$2,000,000
Failure of Supplier to maintain the required insurance will constitute a material breach entitling Sourcewell to immediately terminate this Contract for default.

B. CERTIFICATES OF INSURANCE. Prior to commencing under this Contract, Supplier must furnish to Sourcewell a certificate of insurance, as evidence of the insurance required under this Contract. Prior to expiration of the policy(ies), renewal certificates must be mailed to Sourcewell, 202 12th Street Northeast, P.O. Box 219, Staples, MN 56479 or sent to the Sourcewell Supplier Development Administrator assigned to this Contract. The certificates must be signed by a person authorized by the insurer(s) to bind coverage on their behalf.

Failure to request certificates of insurance by Sourcewell, or failure of Supplier to provide certificates of insurance, in no way limits or relieves Supplier of its duties and responsibilities in this Contract.

C. ADDITIONAL INSURED ENDORSEMENT. Supplier agrees to list Sourcewell and its Participating Entities, including their officers, agents, and employees, as an additional insured under the Supplier’s commercial general liability insurance policy with respect to liability arising out of activities, “operations,” or “work” performed by or on behalf of Supplier, and products and completed operations of Supplier.

D. WAIVER OF SUBROGATION. Omitted.

E. UMBRELLA/EXCESS LIABILITY/SELF-INSURED RETENTION. The limits required by this Contract can be met by either providing a primary policy or in combination with umbrella/excess liability policy(ies), or self-insured retention.

19. COMPLIANCE
A. LAWS AND REGULATIONS. All Equipment, Products, or Services provided under this Contract must comply fully with applicable federal laws and regulations, and with the laws in the states and provinces in which the Equipment, Products, or Services are sold. 













 

EXHIBIT 1 576
113021-OKC
Rev. 3/2021 13
B. LICENSES. Supplier must maintain a valid and current status on all required federal, state/provincial, and local licenses, bonds, and permits required for the operation of the business that the Supplier conducts with Sourcewell and Participating Entities.

20. BANKRUPTCY, DEBARMENT, OR SUSPENSION CERTIFICATION
Supplier certifies and warrants that it is not in bankruptcy or that it has previously disclosed in writing certain information to Sourcewell related to bankruptcy actions. If at any time during this Contract Supplier declares bankruptcy, Supplier must immediately notify Sourcewell in writing.

Supplier certifies and warrants that neither it nor its principals are presently debarred, suspended, proposed for debarment, declared ineligible, or voluntarily excluded from programs operated by the State of Minnesota; the United States federal government or the Canadian government, as applicable; or any Participating Entity. Supplier certifies and warrants that neither it nor its principals have been convicted of a criminal offense related to the subject matter of this Contract. Supplier further warrants that it will provide immediate written notice to Sourcewell if this certification changes at any time.

21. PROVISIONS FOR NON-UNITED STATES FEDERAL ENTITY PROCUREMENTS UNDER

UNITED STATES FEDERAL AWARDS OR OTHER AWARDS
Participating Entities that use United States federal grant or FEMA funds to purchase goods or services from this Contract may be subject to additional requirements including the procurement standards of the Uniform Administrative Requirements, Cost Principles and Audit Requirements for Federal Awards, 2 C.F.R. § 200. Participating Entities may have additional requirements based on specific funding source terms or conditions. Within this Article, all references to “federal” should be interpreted to mean the United States federal government.

The following list only applies when a Participating Entity accesses Supplier’s Equipment, Products, or Services with United States federal funds.

A. EQUAL EMPLOYMENT OPPORTUNITY. Except as otherwise provided under 41 C.F.R. § 60, all contracts that meet the definition of “federally assisted construction contract” in 41 C.F.R. § 60-

1.3 must include the equal opportunity clause provided under 41 C.F.R. §60-1.4(b), in accordance with Executive Order 11246, “Equal Employment Opportunity” (30 FR 12319, 12935, 3 C.F.R. §, 1964-1965 Comp., p. 339), as amended by Executive Order 11375, “Amending Executive Order 11246 Relating to Equal Employment Opportunity,” and implementing regulations at 41 C.F.R. § 60, “Office of Federal Contract Compliance Programs, Equal Employment Opportunity, Department of Labor.” The equal opportunity clause is incorporated herein by reference.














 

EXHIBIT 1 577
113021-OKC
Rev. 3/2021 14
B. DAVIS-BACON ACT, AS AMENDED (40 U.S.C. § 3141-3148). When required by federal program legislation, all prime construction contracts in excess of $2,000 awarded by nonfederal entities must include a provision for compliance with the Davis-Bacon Act (40 U.S.C. § 3141-3144, and 3146-3148) as supplemented by Department of Labor regulations (29 C.F.R. § 5, “Labor Standards Provisions Applicable to Contracts Covering Federally Financed and Assisted Construction”). In accordance with the statute, contractors must be required to pay wages to laborers and mechanics at a rate not less than the prevailing wages specified in a wage determination made by the Secretary of Labor. In addition, contractors must be required to pay wages not less than once a week. The non-federal entity must place a copy of the current prevailing wage determination issued by the Department of Labor in each solicitation. The decision to award a contract or subcontract must be conditioned upon the acceptance of the wage determination. The non-federal entity must report all suspected or reported violations to the federal awarding agency. The contracts must also include a provision for compliance with the Copeland “Anti-Kickback” Act (40 U.S.C. § 3145), as supplemented by Department of Labor regulations (29 C.F.R. § 3, “Contractors and Subcontractors on Public Building or Public Work Financed in Whole or in Part by Loans or Grants from the United States”). The Act provides that each contractor or subrecipient must be prohibited from inducing, by any means, any person employed in the construction, completion, or repair of public work, to give up any part of the compensation to which he or she is otherwise entitled. The non-federal entity must report all suspected or reported violations to the federal awarding agency. Supplier must be in compliance with all applicable Davis-Bacon Act provisions.

C. CONTRACT WORK HOURS AND SAFETY STANDARDS ACT (40 U.S.C. § 3701-3708). Where applicable, all contracts awarded by the non-federal entity in excess of $100,000 that involve the employment of mechanics or laborers must include a provision for compliance with 40 U.S.C. §§ 3702 and 3704, as supplemented by Department of Labor regulations (29 C.F.R. § 5).

Under 40 U.S.C. § 3702 of the Act, each contractor must be required to compute the wages of every mechanic and laborer on the basis of a standard work week of 40 hours. Work in excess of the standard work week is permissible provided that the worker is compensated at a rate of not less than one and a half times the basic rate of pay for all hours worked in excess of 40 hours in the work week. The requirements of 40 U.S.C. § 3704 are applicable to construction work and provide that no laborer or mechanic must be required to work in surroundings or under working conditions which are unsanitary, hazardous or dangerous. These requirements do not apply to the purchases of supplies or materials or articles ordinarily available on the open market, or contracts for transportation or transmission of intelligence. This provision is hereby incorporated by reference into this Contract. Supplier certifies that during the term of an award for all contracts by Sourcewell resulting from this procurement process, Supplier must comply with applicable requirements as referenced above.

D. RIGHTS TO INVENTIONS MADE UNDER A CONTRACT OR AGREEMENT. If the federal award meets the definition of “funding agreement” under 37 C.F.R. § 401.2(a) and the recipient or subrecipient wishes to enter into a contract with a small business firm or nonprofit organization regarding the substitution of parties, assignment or performance of experimental, 













 

EXHIBIT 1 578
113021-OKC
Rev. 3/2021 15
developmental, or research work under that “funding agreement,” the recipient or subrecipient must comply with the requirements of 37 C.F.R. § 401, “Rights to Inventions Made by Nonprofit Organizations and Small Business Firms Under Government Grants, Contracts and Cooperative Agreements,” and any implementing regulations issued by the awarding agency. Supplier certifies that during the term of an award for all contracts by Sourcewell resulting from this procurement process, Supplier must comply with applicable requirements as referenced above.

E. CLEAN AIR ACT (42 U.S.C. § 7401-7671Q.) AND THE FEDERAL WATER POLLUTION CONTROL ACT (33 U.S.C. § 1251-1387). Contracts and subgrants of amounts in excess of $150,000 require the non-federal award to agree to comply with all applicable standards, orders or regulations issued pursuant to the Clean Air Act (42 U.S.C. § 7401- 7671q) and the Federal Water Pollution Control Act as amended (33 U.S.C. § 1251- 1387). Violations must be reported to the Federal awarding agency and the Regional Office of the Environmental Protection Agency (EPA).

Supplier certifies that during the term of this Contract will comply with applicable requirements as referenced above.

F. DEBARMENT AND SUSPENSION (EXECUTIVE ORDERS 12549 AND 12689). A contract award (see 2 C.F.R. § 180.220) must not be made to parties listed on the government wide exclusions in the System for Award Management (SAM), in accordance with the OMB guidelines at 2 C.F.R. §180 that implement Executive Orders 12549 (3 C.F.R. § 1986 Comp., p. 189) and 12689 (3 C.F.R. § 1989 Comp., p. 235), “Debarment and Suspension.” SAM Exclusions contains the names of parties debarred, suspended, or otherwise excluded by agencies, as well as parties declared ineligible under statutory or regulatory authority other than Executive Order 12549. Supplier certifies that neither it nor its principals are presently debarred, suspended, proposed for debarment, declared ineligible, or voluntarily excluded from participation by any federal department or agency.

G. BYRD ANTI-LOBBYING AMENDMENT, AS AMENDED (31 U.S.C. § 1352). Suppliers must file any required certifications. Suppliers must not have used federal appropriated funds to pay any person or organization for influencing or attempting to influence an officer or employee of any agency, a member of Congress, officer or employee of Congress, or an employee of a member of Congress in connection with obtaining any federal contract, grant, or any other award covered by 31 U.S.C. § 1352. Suppliers must disclose any lobbying with non-federal funds that takes place in connection with obtaining any federal award. Such disclosures are forwarded from tier to tier up to the non-federal award. Suppliers must file all certifications and disclosures required by, and otherwise comply with, the Byrd Anti-Lobbying Amendment (31 U.S.C. § 1352).

H. RECORD RETENTION REQUIREMENTS. To the extent applicable, Supplier must comply with the record retention requirements detailed in 2 C.F.R. § 200.333. The Supplier further certifies that it will retain all records as required by 2 C.F.R. § 200.333 for a period of 3 years after grantees or subgrantees submit final expenditure reports or quarterly or annual financial reports, as applicable, and all other pending matters are closed. 













 

EXHIBIT 1 579
113021-OKC
Rev. 3/2021 16
I. ENERGY POLICY AND CONSERVATION ACT COMPLIANCE. To the extent applicable, Supplier must comply with the mandatory standards and policies relating to energy efficiency which are contained in the state energy conservation plan issued in compliance with the Energy Policy and Conservation Act.

J. BUY AMERICAN PROVISIONS COMPLIANCE. To the extent applicable, Supplier must comply with all applicable provisions of the Buy American Act. Purchases made in accordance with the Buy American Act must follow the applicable procurement rules calling for free and open competition.

K. ACCESS TO RECORDS (2 C.F.R. § 200.336). Supplier agrees that duly authorized representatives of a federal agency must have access to any books, documents, papers and records of Supplier that are directly pertinent to Supplier’s discharge of its obligations under this Contract for the purpose of making audits, examinations, excerpts, and transcriptions. The right also includes timely and reasonable access to Supplier’s personnel for the purpose of interview and discussion relating to such documents.

L. PROCUREMENT OF RECOVERED MATERIALS (2 C.F.R. § 200.322). A non-federal entity that is a state agency or agency of a political subdivision of a state and its contractors must comply with Section 6002 of the Solid Waste Disposal Act, as amended by the Resource Conservation and Recovery Act. The requirements of Section 6002 include procuring only items designated in guidelines of the Environmental Protection Agency (EPA) at 40 C.F.R. § 247 that contain the highest percentage of recovered materials practicable, consistent with maintaining a satisfactory level of competition, where the purchase price of the item exceeds $10,000 or the value of the quantity acquired during the preceding fiscal year exceeded $10,000; procuring solid waste management services in a manner that maximizes energy and resource recovery; and establishing an affirmative procurement program for procurement of recovered materials identified in the EPA guidelines.

M. FEDERAL SEAL(S), LOGOS, AND FLAGS. The Supplier not use the seal(s), logos, crests, or reproductions of flags or likenesses of Federal agency officials without specific pre-approval.

N. NO OBLIGATION BY FEDERAL GOVERNMENT. The U.S. federal government is not a party to this Contract or any purchase by an Participating Entity and is not subject to any obligations or liabilities to the Participating Entity, Supplier, or any other party pertaining to any matter resulting from the Contract or any purchase by an authorized user.

O. PROGRAM FRAUD AND FALSE OR FRAUDULENT STATEMENTS OR RELATED ACTS. The Contractor acknowledges that 31 U.S.C. 38 (Administrative Remedies for False Claims and Statements) applies to the Supplier’s actions pertaining to this Contract or any purchase by a Participating Entity.














 

EXHIBIT 1 580
113021-OKC
Rev. 3/2021 17
P. FEDERAL DEBT. The Supplier certifies that it is non-delinquent in its repayment of any federal debt. Examples of relevant debt include delinquent payroll and other taxes, audit disallowance, and benefit overpayments.

Q. CONFLICTS OF INTEREST. The Supplier must notify the U.S. Office of General Services, Sourcewell, and Participating Entity as soon as possible if this Contract or any aspect related to the anticipated work under this Contract raises an actual or potential conflict of interest (as described in 2 C.F.R. Part 200). The Supplier must explain the actual or potential conflict in writing in sufficient detail so that the U.S. Office of General Services, Sourcewell, and Participating Entity are able to assess the actual or potential conflict; and provide any additional information as necessary or requested.

R. U.S. EXECUTIVE ORDER 13224. The Supplier, and its subcontractors, must comply with U.S.

Executive Order 13224 and U.S. Laws that prohibit transactions with and provision of resources and support to individuals and organizations associated with terrorism.

S. PROHIBITION ON CERTAIN TELECOMMUNICATIONS AND VIDEO SURVEILLANCE SERVICES OR EQUIPMENT. To the extent applicable, Supplier certifies that during the term of this Contract it will comply with applicable requirements of 2 C.F.R. § 200.216.

T. DOMESTIC PREFERENCES FOR PROCUREMENTS. To the extent applicable, Supplier certifies that during the term of this Contract will comply with applicable requirements of 2 C.F.R. § 200.322.

22. CANCELLATION
Sourcewell or Supplier may cancel this Contract at any time, with or without cause, upon 60 days’ written notice to the other party. However, Sourcewell may cancel this Contract immediately upon discovery of a material defect in any certification made in Supplier’s Proposal. Cancellation of this Contract does not relieve either party of financial, product, or service obligations incurred or accrued prior to cancellation. ** Remainder of page intentionally blank **














 

EXHIBIT 1 581














 









EXHIBIT 1 582
5)3)LUHILJKWLQJ$SSDUDWXVDQG)LUH6HUYLFH9HKLFOHV 9HQGRU'HWDLOV
&RPSDQ\1DPH
3LHUFH0DQXIDFWXULQJ
'RHV\RXUFRPSDQ\FRQGXFW
EXVLQHVVXQGHUDQ\RWKHUQDPH",I
\HVSOHDVHVWDWH

:,6&216,1
$GGUHVV

$PHULFDQ'ULYH
$SSOHWRQ:,

&RQWDFW
0LFKHOOH6ZRNRZVNL
(PDLO
PVZRNRZVNL#SLHUFHPIJFRP
3KRQH


)D[


+67

6XEPLVVLRQ'HWDLOV
&UHDWHG2Q
0RQGD\2FWREHU


6XEPLWWHG2Q
7XHVGD\1RYHPEHU


6XEPLWWHG%\
0LFKHOOH6ZRNRZVNL
(PDLO
PVZRNRZVNL#SLHUFHPIJFRP
7UDQVDFWLRQ
IIIEG
EGEDIG
FE

6XEPLWWHU
V,3$GGUHVV



Bid Number: RFP 113021 Vendor Name: Pierce Manufacturing 













 

EXHIBIT 1 583
6SHFLILFDWLRQV
7DEOH
3URSRVHU,GHQWLW\ $XWKRUL]HG5HSUHVHQWDWLYHV
*HQHUDO,QVWUXFWLRQV
DSSOLHVWRDOO7DEOHV
6RXUFHZHOOSUHIHUVDEULHIEXWWKRURXJKUHVSRQVHWRHDFKTXHVWLRQ'RQRWPHUHO\DWWDFK DGGLWLRQDOGRFXPHQWVWR\RXUUHVSRQVHZLWKRXWDOVRSURYLGLQJDVXEVWDQWLYHUHVSRQVH'RQRWOHDYHDQVZHUVEODQN UHVSRQG³1$´LIWKH
TXHVWLRQGRHVQRWDSSO\WR\RX
SUHIHUDEO\ZLWKDQH[SODQDWLRQ

/LQH
,WHP 4XHVWLRQ 5HVSRQVH

 3URSRVHUௐ/HJDOௐ1DPHௐ
RQHௐOHJDOௐHQWLW\ௐRQO\

ௐௐ

,QௐWKHௐHYHQWௐRIௐDZDUGௐZLOOௐH[HFXWHௐWKHௐ
UHVXOWLQJௐFRQWUDFWௐDVௐ6XSSOLHU

2VKNRVKௐ&RUSRUDWLRQ


 ,GHQWLI\ௐDOOௐVXEVLGLDU\ௐHQWLWLHVௐRIௐWKHௐ3URSRVHUௐ
ZKRVHௐHTXLSPHQWௐSURGXFWVௐRUௐVHUYLFHVௐDUHௐ
LQFOXGHGௐLQௐWKHௐ3URSRVDO
3LHUFHௐ0DQXIDFWXULQJௐ,QFௐ
2VKNRVKௐ$LUSRUWௐ3URGXFWVௐ//& 

 ,GHQWLI\ௐDOOௐDSSOLFDEOHௐDVVXPHGௐQDPHVௐRUௐ'%$ௐ
QDPHVௐRIௐWKHௐ3URSRVHUௐRUௐ3URSRVHU
Vௐ
VXEVLGLDULHVௐLQௐ/LQHௐௐRUௐ/LQHௐௐDERYH
$VௐXVHGௐKHUHLQௐWKHௐ³&RPSDQ\´ௐ³ZH´ௐ³XV´ௐDQGௐ³RXU´ௐUHIHUVௐWRௐ2VKNRVKௐ&RUSRUDWLRQௐ DQGௐLWVௐFRQVROLGDWHGௐVXEVLGLDULHVௐ³2VKNRVK´ௐUHIHUVௐWRௐ2VKNRVKௐ&RUSRUDWLRQௐௐ VXEVLGLDULHVௐ3UDWWௐ ௐ0LOOHUௐ(QJLQHHULQJௐ ௐ)DEULFDWLRQVௐ//&ௐ 3UDWWௐ0LOOHU
ௐ3LHUFHௐ
0DQXIDFWXULQJௐ,QFௐ
3LHUFH
ௐ0F1HLOXVௐ&RPSDQLHVௐ,QFௐ
0F1HLOXV
ௐDQGௐLWVௐௐZKROO\ௐ
RZQHGௐௐVXEVLGLDULHVௐௐ2VKNRVKௐௐ$LUSRUWௐௐ3URGXFWVௐௐ//&ௐௐ $LUSRUWௐௐ3URGXFWV
ௐௐ
.HZDXQHHௐௐ)DEULFDWLRQVௐௐ//&ௐௐ
.HZDXQHHௐ
,07
ௐRUௐDQ\ௐRWKHUௐVXEVLGLDULHVௐௐ2WKHUௐ
DVVXPHௐQDPHVௐKHUHLQௐDUHௐRIWHQௐLGHQWLILHGௐWRௐEHௐ)URQWOLQHௐ&RPPXQLFDWLRQVௐ$5))ௐ $LUSRUWௐௐ3LHUFH


 3URSRVHUௐ3K\VLFDOௐ$GGUHVV
2VKNRVKௐ&RUSRUDWLRQ

ௐ)RXUௐ:KHHOௐ'Uௐ
2VKNRVKௐ:,ௐ

3LHUFHௐ0DQXIDFWXULQJௐ,QF
ௐ$PHULFDQௐ'U
$SSOHWRQௐ:,ௐ

2VKNRVKௐ$LUSRUWௐ3URGXFWVௐ//&
ௐ&RXQW\ௐ5Gௐ2ௐ
1HHQDKௐ:,ௐ



 3URSRVHUௐZHEVLWHௐDGGUHVVௐ
RUௐDGGUHVVHV

ZZZRVKNRVKFRUSFRPௐ
ZZZ3LHUFHPIJFRPௐ
ZZZIURQWOLQHFRPPFRP
ZZZRVKNRVKDLUSRUWFRP


 3URSRVHU
Vௐ$XWKRUL]HGௐ5HSUHVHQWDWLYHௐ
QDPHௐ
WLWOHௐDGGUHVVௐHPDLOௐDGGUHVVௐ ௐSKRQH
ௐ
7KHௐ
UHSUHVHQWDWLYHௐPXVWௐKDYHௐDXWKRULW\ௐWRௐVLJQௐ
WKHௐ³3URSRVHU¶Vௐ$VVXUDQFHௐRIௐ&RPSOLDQFH´ௐRQௐ
EHKDOIௐRIௐWKHௐ3URSRVHUௐDQGௐLQௐWKHௐHYHQWௐRIௐ
DZDUGௐZLOOௐEHௐH[SHFWHGௐWRௐH[HFXWHௐWKHௐ
UHVXOWLQJௐFRQWUDFW

-DPHVௐ:ௐ-RKQVRQ
([HFXWLYHௐ9LFHௐ3UHVLGHQWௐDQGௐ3UHVLGHQWௐ)LUHௐ ௐ(PHUJHQF\ௐ6HJPHQW 3LHUFHௐ0DQXIDFWXULQJௐ,QFௐௐௐௐௐௐௐௐ
ௐ$PHULFDQௐ'ULYH
$SSOHWRQௐ:,ௐௐ
ௐௐௐௐ
(PDLO
ௐMMRKQVRQ#SLHUFHPIJFRP
3KRQH
ௐ

5HIHUௐWRௐDXWKRUL]HGௐVLJQHUVௐIRUௐ2VKNRVKௐ&RUSRUDWLRQௐ3LHUFHௐ0DQXIDFWXULQJௐDQGௐ 2VKNRVKௐ$LUSRUWௐ3URGXFWVௐLQௐDGGLWLRQDOௐGRFXPHQWV


 3URSRVHU
VௐSULPDU\ௐFRQWDFWௐIRUௐWKLVௐSURSRVDOௐ

QDPHௐWLWOHௐDGGUHVVௐHPDLOௐDGGUHVVௐ ௐSKRQH

0LFKHOOHௐ6ZRNRZVNLௐ
6DOHVௐ2SHUDWLRQVௐ0DQDJHUௐ3LHUFHௐ0DQXIDFWXULQJௐ,QF
ௐ$PHULFDQௐ'ULYHௐ$SSOHWRQௐ:,ௐ

(PDLO
ௐPVZRNRZVNL#SLHUFHPIJFRP
3KRQH
ௐௐ



 3URSRVHU
VௐRWKHUௐFRQWDFWVௐIRUௐWKLVௐSURSRVDOௐLIௐ
DQ\ௐ
QDPHௐWLWOHௐDGGUHVVௐHPDLOௐDGGUHVVௐ ௐ
SKRQH

%ULDQQDௐ3URSVRQௐ
6DOHVௐ5HSUHVHQWDWLYHௐ2VKNRVKௐ$LUSRUWௐ3URGXFWVௐ//&ௐ
ௐ&RXQW\ௐ5'ௐ2ௐ
1HHQDKௐ:,ௐ

(PDLO
ௐESURSVRQ#DLUSRUWRVKNRVKFRUSFRP
3KRQH
ௐ

7DEOH
&RPSDQ\,QIRUPDWLRQDQG)LQDQFLDO6WUHQJWK
/LQH
,WHP 4XHVWLRQ 5HVSRQVH

Bid Number: RFP 113021 Vendor Name: Pierce Manufacturing 













 

EXHIBIT 1 584

3URYLGH D EULHI KLVWRU\ RI \RXU FRPSDQ\
LQFOXGLQJௐ\RXUௐFRPSDQ\¶VௐFRUHௐYDOXHVௐ
EXVLQHVVௐSKLORVRSK\ௐDQGௐLQGXVWU\ௐORQJHYLW\ௐ
UHODWHGௐWRௐWKHௐUHTXHVWHGௐHTXLSPHQWௐSURGXFWVௐ
RUௐVHUYLFHV
2VKNRVK &RUSRUDWLRQ 2YHUYLHZ
2VKNRVKௐ&RUSRUDWLRQௐZDVௐIRXQGHGௐLQௐ
ௐGULYHQௐE\ௐDௐEUHDNWKURXJKௐIRXUZKHHOௐ
GULYHௐV\VWHPௐWKDWௐJDYHௐSHRSOHௐWKHௐFRXUDJHௐDQGௐFRQILGHQFHௐWRௐJRௐSODFHVௐWKH\ௐQHYHUௐ WKRXJKWௐWKH\ௐZRXOGௐ7RGD\ௐPRUHௐWKDQௐௐ2VKNRVKௐWHDPௐPHPEHUVௐDUHௐSXWWLQJௐ RYHUௐௐDFWLYHௐSDWHQWHGௐWHFKQRORJLHVௐWRௐZRUNௐVHUYLQJௐGHYHORSLQJௐDQGௐFRQQHFWLQJௐ FRPPXQLWLHVௐDURXQGௐWKHௐZRUOGௐ2VKNRVKௐ&RUSRUDWLRQௐLVௐDௐOHDGLQJௐPDQXIDFWXUHUௐDQGௐ PDUNHWHUௐRIௐDFFHVVௐHTXLSPHQWௐVSHFLDOW\ௐYHKLFOHVௐDQGௐWUXFNௐERGLHVௐIRUௐWKHௐSULPDU\ௐ PDUNHWVௐRIௐDFFHVVௐHTXLSPHQWௐGHIHQVHௐILUHௐ ௐHPHUJHQF\ௐDQGௐPXQLFLSDOௐUHIXVHௐ KDXOLQJௐFRQFUHWHௐSODFHPHQWௐDVௐZHOOௐDVௐDLUSRUWௐVHUYLFHVௐVௐ2VKNRVKௐSURGXFWVௐFDQௐEHௐ IRXQGௐLQௐPRUHௐWKDQௐௐFRXQWULHVௐXQGHUௐWKHௐEUDQGVௐRIௐ-/*Šௐ3LHUFHŠௐ2VKNRVKŠௐ 'HIHQVHௐ0F1HLOXVŠௐ,07Šௐ-HUU'DQŠௐ)URQWOLQHŒௐ2VKNRVKŠௐ$LUSRUWௐ3URGXFWVௐDQGௐ /RQGRQŒௐDQGௐ3UDWWௐ0LOOHUௐ
3LHUFHௐDQGௐ$LUSRUWௐ3URGXFWVௐDUHௐVXEVLGLDULHVௐRIௐ2VKNRVKௐDQGௐDUHௐSDUWௐRIௐWKHௐ)LUHௐ ௐ (PHUJHQF\ௐ6HJPHQWௐRIௐ2VKNRVKௐ:HௐEHOLHYHௐLQௐDGYDQFLQJௐWKHௐZRUOGௐDURXQGௐXVௐ WKURXJKௐEXLOGLQJௐVHUYLQJௐDQGௐSURWHFWLQJௐSHRSOHௐDQGௐFRPPXQLWLHVௐ:HௐDUHௐXQLWHGௐE\ௐ DௐFRPPRQௐSXUSRVH
ௐWRௐPDNHௐDௐGLIIHUHQFHௐLQௐSHRSOH¶VௐOLYHVௐ2XUௐYDOXHVௐDUHௐWKHௐ EHOLHIௐV\VWHPௐWKDWௐKHOSVௐXVௐHQVXUHௐRXUௐEHKDYLRUVௐDUHௐDOLJQHGௐZLWKௐRXUௐSXUSRVHௐDQGௐ GULYHௐXVௐWRௐGRௐJUHDWௐZRUNௐIRUௐJUHDWௐSHRSOHௐ
2VKNRVKௐ&RUHௐ9DOXHV
ௐ
:(ௐ387ௐ3(23/(ௐ),567ௐ
‡ௐ:HௐWUHDWௐSHRSOHௐKRZௐWKH\ௐQHHGௐWRௐEHௐWUHDWHGௐ
‡ௐ:HௐNHHSௐSHRSOHௐVDIHௐZLWKLQௐRXUௐZDOOVௐDQGௐWKRVHௐXVLQJௐRXUௐSURGXFWVௐ ‡ௐ:HௐFDUHௐIRUௐWKHௐHPRWLRQDOௐSK\VLFDOௐDQGௐILQDQFLDOௐZHOOEHLQJௐRIௐRXUௐSHRSOHௐ ‡ௐ:HௐFHOHEUDWHௐZKDWௐPDNHVௐHDFKௐRIௐXVௐXQLTXHௐ
‡ௐ:HௐYDOXHௐRWKHU¶VௐZRUGVௐDQGௐLGHDVௐ
‡ௐ:HௐUHVSHFWௐWKHௐLPSDFWௐZHௐKDYHௐRQௐHDFKௐRWKHU
ௐRQௐWKHௐSHRSOHௐZHௐVHUYHௐDQGௐLQௐ
FRPPXQLWLHVௐDURXQGௐWKHௐZRUOGௐ
:(ௐ'2ௐ7+(ௐ5,*+7ௐ7+,1*ௐ
‡ௐ:HௐGRௐWKHௐULJKWௐWKLQJௐWKHௐULJKWௐZD\ௐIRUௐWKHௐULJKWௐUHDVRQVௐ ‡ௐ:HௐWDNHௐUHVSRQVLELOLW\ௐIRUௐRXUௐDFWLRQVௐ
‡ௐ:HௐVSHDNௐXSௐDQGௐVKDUHௐRXUௐWKRXJKWVௐDQGௐFRQFHUQVௐ
‡ௐ:HௐNHHSௐRXUௐSURPLVHVௐ
‡ௐ:HௐUHVSHFWௐRXUௐHQYLURQPHQW
ௐERWKௐZKHUHௐZHௐZRUNௐDQGௐWKHௐSODQHWௐZHௐUHO\ௐRQௐ
:(ௐ3(56(9(5(
‡ௐ:HௐSXVKௐWKHௐERXQGVௐRIௐWHFKQRORJ\ௐDQGௐHQJLQHHULQJௐWRௐEULQJௐYDOXHௐWRௐRXUௐ FXVWRPHUVௐDQGௐWKRVHௐZKRௐFRXQWௐRQௐXVௐ
‡ௐ:HௐFKDOOHQJHௐWKHௐLPSRVVLEOHௐWRௐPDNHௐDௐGLIIHUHQFHௐHYHU\ௐGD\ௐ ‡ௐ:HௐDUHௐFRXUDJHRXVௐDQGௐVWHDGIDVWௐ
‡ௐ:HௐVWULYHௐWRௐRYHUFRPHௐREVWDFOHVௐDQGௐDFKLHYHௐRXUௐJRDOVௐ :(ௐ$5(ௐ%(77(5ௐ72*(7+(5ௐ
‡ௐ:HௐZHOFRPHௐLGHDVௐGLIIHUHQWௐIURPௐRXUௐRZQௐ
‡ௐ:HௐUHO\ௐRQௐGLYHUVLW\ௐWRௐGULYHௐLQQRYDWLRQௐ
‡ௐ:HௐFUHDWHௐDQௐLQFOXVLYHௐHPSRZHULQJௐHQYLURQPHQWௐIRUௐDOOௐ ‡ௐ:HௐZRUNௐWRJHWKHUௐDFURVVௐJHRJUDSKLHVௐSODWIRUPVௐEXVLQHVVௐXQLWVௐDQGௐIXQFWLRQVௐWRௐ KHOSௐRXUௐFRPSDQ\ௐUHDFKௐLWVௐIXOOHVWௐSRWHQWLDO
%XVLQHVVௐ3KLORVRSK\
ௐ
2XUௐVWUDWHJ\ௐLVௐ³,QQRYDWHௐ6HUYHௐ$GYDQFH´ௐ:HௐLQQRYDWHௐFXVWRPHUௐVROXWLRQVௐE\ௐ FRPELQLQJௐOHDGLQJௐWHFKQRORJ\ௐDQGௐRSHUDWLRQDOௐVWUHQJWKௐWRௐHPSRZHUௐDQGௐSURWHFWௐWKHௐ HYHU\GD\ௐKHURௐ:HௐVHUYHௐDQGௐVXSSRUWௐWKRVHௐZKRௐUHO\ௐRQௐXVௐZLWKௐDௐUHOHQWOHVVௐIRFXVௐ WKURXJKRXWௐWKHௐSURGXFWௐOLIHF\FOHௐ:HௐDGYDQFHௐE\ௐH[SDQGLQJௐLQWRௐQHZௐPDUNHWVௐDQGௐ JHRJUDSKLHVௐWRௐPDNHௐDௐGLIIHUHQFHௐDURXQGௐWKHௐZRUOG
$VௐDௐFRUSRUDWLRQௐRXUௐFXOWXUHௐLVௐRQHௐFRPPLWWHGௐWRௐFRQGXFWLQJௐEXVLQHVVௐZLWKௐLQWHJULW\ௐ LQௐDFFRUGDQFHௐZLWKௐWKHௐKLJKHVWௐHWKLFDOௐVWDQGDUGVௐDQGௐLQௐFRPSOLDQFHௐZLWKௐDSSOLFDEOHௐ ODZVௐDQGௐUHJXODWLRQVௐ7KHௐJXLGHOLQHVௐODZVௐUHJXODWLRQVௐSROLFLHVௐDQGௐSURFHGXUHVௐWKDWௐ JRYHUQௐRXUௐFRQGXFWௐDVௐHPSOR\HHVௐDQGௐFRQWUDFWRUVௐRIௐ2VKNRVKௐ&RUSRUDWLRQௐDUHௐ HPERGLHGௐLQௐRXUௐ&RGHௐRIௐ(WKLFVௐ ௐ6WDQGDUGVௐRIௐ&RQGXFWௐௐ7KHௐ2VKNRVKௐ:D\ௐ %XVLQHVVௐ/RQJHYLW\
ௐ
3LHUFHௐZDVௐIRXQGHGௐLQௐ
ௐDQGௐLVௐWKHௐOHDGLQJௐGRPHVWLFௐGHVLJQHUௐDQGௐPDQXIDFWXUHUௐ RIௐILUHௐDSSDUDWXVௐDVVHPEOHGௐRQௐFXVWRPௐFKDVVLVௐGHVLJQHGௐDQGௐPDQXIDFWXUHGௐWRௐ PHHWௐWKHௐVSHFLDOௐQHHGVௐRIௐILUHILJKWHUVௐ3LHUFHௐDOVRௐGHVLJQVௐDQGௐPDQXIDFWXUHVௐILUHௐ DSSDUDWXVௐDVVHPEOHGௐRQௐFRPPHUFLDOO\ௐDYDLODEOHௐFKDVVLVௐZKLFKௐDUHௐSURGXFHGௐIRUௐ PXOWLSOHௐHQGFXVWRPHUௐDSSOLFDWLRQVௐ3LHUFH¶VௐHQJLQHHULQJௐH[SHUWLVHௐDOORZVௐLWௐWRௐGHVLJQௐ LWVௐYHKLFOHVௐWRௐPHHWௐVWULQJHQWௐLQGXVWU\ௐJXLGHOLQHVௐDQGௐJRYHUQPHQWௐUHJXODWLRQVௐIRUௐ VDIHW\ௐDQGௐHIIHFWLYHQHVVௐ3LHUFHௐSULPDULO\ௐVHUYHVௐGRPHVWLFௐPXQLFLSDOௐFXVWRPHUVௐEXWௐ DOVRௐVHOOVௐILUHௐDSSDUDWXVௐWRௐWKHௐ'R'ௐDLUSRUWVௐXQLYHUVLWLHVௐDQGௐODUJHௐLQGXVWULDOௐ FRPSDQLHVௐDQGௐLQௐLQWHUQDWLRQDOௐPDUNHWVௐ3LHUFH¶VௐKLVWRU\ௐRIௐLQQRYDWLRQௐUHVHDUFKௐDQGௐ GHYHORSPHQWௐLQௐFRQVXOWDWLRQௐZLWKௐILUHILJKWHUVௐKDVௐUHVXOWHGௐLQௐDௐEURDGௐSURGXFWௐOLQHௐWKDWௐ IHDWXUHVௐDௐZLGHௐUDQJHௐRIௐLQQRYDWLYHௐKLJKTXDOLW\ௐFXVWRPௐDQGௐFRPPHUFLDOௐILUHILJKWLQJௐ HTXLSPHQWௐZLWKௐDGYDQFHGௐILUHௐVXSSUHVVLRQௐFDSDELOLWLHVௐ,QௐDQௐHIIRUWௐWRௐEHௐDௐVLQJOH VRXUFHௐVXSSOLHUௐIRUௐLWVௐFXVWRPHUVௐ3LHUFHௐRIIHUVௐDௐIXOOௐOLQHௐRIௐFXVWRPௐDQGௐFRPPHUFLDOௐ ILUHௐDSSDUDWXVௐDQGௐHPHUJHQF\ௐYHKLFOHVௐLQFOXGLQJௐSXPSHUVௐDHULDOௐSODWIRUPௐODGGHUௐ DQG WLOOHU WUXFNV WDQNHUV OLJKW PHGLXP DQG KHDY\GXW\ௐUHVFXH YHKLFOHV ZLOGODQG 

Bid Number: RFP 113021 Vendor Name: Pierce Manufacturing 













 

EXHIBIT 1 585
URXJK WHUUDLQ UHVSRQVH YHKLFOHV PRELOH FRPPDQG DQG FRQWURO FHQWHUV ERPE VTXDG YHKLFOHVௐKD]DUGRXVௐPDWHULDOVௐFRQWUROௐYHKLFOHVௐDQGௐRWKHUௐHPHUJHQF\ௐUHVSRQVHௐYHKLFOHV 5HIHUௐWRௐ3LHUFHௐ7LPHOLQHSGIௐLQௐ)LQDQFLDOௐ6WUHQJWKௐDQGௐ6WDELOLW\ௐIROGHUௐ 2VKNRVKௐ$LUSRUWௐ3URGXFWVௐLVௐDௐOHDGHUௐLQௐWKHௐGHVLJQௐDQGௐVDOHௐRIௐ$5))ௐYHKLFOHVௐWRௐ GRPHVWLFௐDQGௐLQWHUQDWLRQDOௐDLUSRUWVௐ7KHVHௐKLJKO\ௐVSHFLDOL]HGௐYHKLFOHVௐDUHௐUHTXLUHGௐWRௐ EHௐLQௐVHUYLFHௐDWௐPRVWௐDLUSRUWVௐZRUOGZLGHௐWRௐVXSSRUWௐFRPPHUFLDOௐDLUOLQHVௐLQௐWKHௐHYHQWௐ RIௐDQௐHPHUJHQF\ௐௐ2XUௐILUVWௐ$LUFUDIWௐ5HVFXHௐDQGௐ)LUHௐ)LJKWLQJௐ $5))
ௐYHKLFOHௐZDVௐ
GHOLYHUHGௐWRௐWKHௐ86ௐ1DY\ௐLQௐ
ௐௐ
:HௐDUHௐDEOHௐWRௐDWWUDFWௐDQGௐUHWDLQௐQHZௐFXVWRPHUVௐEHFDXVHௐZHௐWDNHௐSULGHௐLQௐDௐ TXDOLW\ௐSURGXFWௐZHௐEXLOGௐDQGௐSURYLGHௐVHFRQGௐWRௐQRQHௐLQௐVHUYLFHௐDQGௐVXSSRUWௐ QDWLRQZLGHௐ:HௐDUHௐWKHௐOHDGLQJௐPDQXIDFWXUHUௐRIௐILUHௐDSSDUDWXVௐEHFDXVHௐRIௐWKLVௐ±ௐRXUௐ OR\DOௐFXVWRPHUV
5HIHUௐWRௐ
ௐ2VKNRVKௐ&RUSRUDWLRQௐௐ$QQXDOௐ5HSRUWSGIௐ
ௐ2VKNRVKௐ6WUDWHJ\ௐ
,QQRYDWHௐ6HUYHௐ$GYDQFHௐ6WUDWHJ\SGIௐ
ௐ7KHB2VKNRVKB:D\B(QJOLVKSGIௐ
ௐ
B6XVWDLQDELOLW\B5HSRUWSGIௐDQGௐ
ௐ(TXDOௐ(PSOR\PHQWௐ2SSRUWXQLW\SGIௐLQௐ
)LQDQFLDOௐ6WUHQJWKௐDQGௐ6WDELOLW\ௐIROGHUௐIRUௐPRUHௐLQIRUPDWLRQ  :KDWௐDUHௐ\RXUௐFRPSDQ\¶VௐH[SHFWDWLRQVௐLQௐWKHௐ
HYHQWௐRIௐDQௐDZDUG"
7KHௐ6RXUFHZHOOௐFRQVRUWLXPௐSURJUDPௐZLOOௐH[WHQGௐDQRWKHUௐDYHQXHௐIRUௐWKHௐILUHௐLQGXVWU\ௐ FXVWRPHUௐEDVHௐWRௐSXUFKDVHௐDௐILUHௐDSSDUDWXVௐHIILFLHQWO\ௐDQGௐHIIHFWLYHO\ௐWKURXJKௐDௐ SURYHQௐSURJUDP
7KHௐ6RXUFHZHOOௐFRQVRUWLXPௐZLOOௐEHௐDௐQDWLRQZLGHௐLQFOXGLQJௐ&DQDGDௐDYHQXHௐWKDWௐLVௐ SURPRWHGௐDFURVVௐWKHௐ3LHUFHௐVDOHVௐIRUFHௐWKDWௐFRQVLVWVௐRIௐௐDXWKRUL]HGௐ3LHUFHௐ 'HDOHUVௐDQGௐWKHLUௐUHVSHFWLYHௐWHDPௐPHPEHUV
7KHௐIXQGDPHQWDOௐH[SHFWDWLRQௐLVௐDURXQGௐHGXFDWLRQௐDQGௐSURPRWLRQௐ7KHௐ3LHUFHௐ'HDOHUௐ QHWZRUNௐDQGௐ$LUSRUWௐ3URGXFWVௐVDOHVௐWHDPௐLVௐH[SHFWHGௐWRௐXQGHUVWDQGௐRXUௐSURGXFWௐDQGௐ WKHௐWRROVௐDYDLODEOHௐWRௐWKHௐFXVWRPHUௐWRௐDFKLHYHௐZKDWௐLVௐLQௐWKHௐEHVWௐLQWHUHVWௐRIௐWKHௐ FXVWRPHU


 'HPRQVWUDWHௐ\RXUௐILQDQFLDOௐVWUHQJWKௐDQGௐ
VWDELOLW\ௐZLWKௐPHDQLQJIXOௐGDWDௐ7KLVௐFRXOGௐ
LQFOXGHௐVXFKௐLWHPVௐDVௐILQDQFLDOௐVWDWHPHQWVௐ
6(&ௐILOLQJVௐFUHGLWௐDQGௐERQGௐUDWLQJVௐOHWWHUVௐ
RIௐFUHGLWௐDQGௐGHWDLOHGௐUHIHUHQFHௐOHWWHUVௐ
8SORDGௐVXSSRUWLQJௐGRFXPHQWVௐ
DVௐDSSOLFDEOH
ௐ
LQௐWKHௐGRFXPHQWௐXSORDGௐVHFWLRQௐRIௐ\RXUௐ
UHVSRQVH
3LHUFHௐ0DQXIDFWXULQJௐ,QFௐDQGௐ2VKNRVKௐ$LUSRUWௐ3URGXFWVௐ//&ௐDUHௐVXEVLGLDULHVௐRIௐ 2VKNRVKௐ&RUSRUDWLRQௐZKLFKௐLVௐDௐSXEOLFO\ௐWUDGHGௐFRPSDQ\ௐ :HௐKDYHௐDWWDFKHGௐRXUௐDQQXDOௐUHSRUWௐ6(&ௐ)LOLQJVௐDORQJௐZLWKௐWKHௐ'XQQௐ ௐ%UDGVWUHHWௐ UHSRUWௐRIWHQௐXVHGௐE\ௐOHQGHUVௐDQGௐLQYHVWRUVௐWRௐGHWHUPLQHௐDௐFRPSDQ\ VௐHOLJLELOLW\ௐIRUௐ
FUHGLWௐ7KLVௐUHSRUWௐDORQJௐZLWKௐDQ\ௐRIௐWKHௐILQDQFLDOௐVWDWHPHQWVௐGHPRQVWUDWHௐ2VKNRVKௐ &RUSRUDWLRQௐDQGௐLWVௐVXEVLGLDULHVௐWRௐEHௐILQDQFLDOO\ௐVRXQGௐ)RUௐDGGLWLRQDOௐLQIRUPDWLRQௐ SOHDVHௐUHIHUௐWRௐWKHௐEHORZௐSDWK
KWWS
LQYHVWRURVKNRVKFRUSRUDWLRQFRPLQYHVWRUVRYHUYLHZௐௐ 2VKNRVKௐ&RUSRUDWLRQௐPDLQWDLQVௐDQௐLQYHVWPHQWௐJUDGHௐFUHGLWௐUDWLQJௐௐ7KHௐUDWLQJௐ DJHQFLHVௐSHULRGLFDOO\ௐXSGDWHௐWKHௐ&RPSDQ\¶VௐFUHGLWௐUDWLQJVௐDVௐHYHQWVௐRUௐFKDQJHVௐLQௐ HFRQRPLFௐFRQGLWLRQVௐRFFXUௐ$VௐRIௐ6HSWHPEHUௐௐௐWKHௐORQJWHUPௐFUHGLWௐUDWLQJVௐ DVVLJQHGௐWRௐWKHௐ&RPSDQ\¶VௐVHQLRUௐGHEWௐVHFXULWLHVௐE\ௐWKHௐFUHGLWௐUDWLQJௐDJHQFLHVௐ HQJDJHGௐE\ௐWKHௐ&RPSDQ\ௐZHUHௐDVௐIROORZV
ௐௐ)LWFKௐ5DWLQJVௐ%%%
ௐ0RRG\¶Vௐ,QYHVWRUௐ
6HUYLFHVௐ,QFௐ%DDD
ௐ6WDQGDUGVௐ ௐ3RRU¶Vௐ%%%ௐௐ
5HIHUௐWRௐௐ2VKNRVKௐ&RUSௐ4ௐDQG)XOO<HDU5HVXOWVSGIௐௐ2VKNRVKௐ &RUSRUDWLRQௐ)RUPௐ.SGIௐௐ' %ௐ)LQDQFHௐ$QDO\WLFVௐ5HSRUWSGIௐௐ%DQNௐRIௐ $PHULFDௐ2VKNRVKௐ5HIHUHQFHSGIௐௐ3LHUFHௐ0DQXIDFWXULQJௐ&HUWLILFDWHௐRIௐ6WDWXVௐ SGIௐDQGௐௐ2VKNRVKௐ$LUSRUWௐ3URGXFWVௐ&HUWLILFDWHௐRIௐ6WDWXVௐ-XO\ௐSGIௐ LQௐ)LQDQFLDOௐ6WUHQJWKௐDQGௐ6WDELOLW\ௐIROGHUௐIRUௐPRUHௐLQIRUPDWLRQ 

Bid Number: RFP 113021 Vendor Name: Pierce Manufacturing 













 

EXHIBIT 1 586
 :KDWௐLVௐ\RXUௐ86ௐPDUNHWௐVKDUHௐIRUௐWKHௐ
VROXWLRQVௐWKDWௐ\RXௐDUHௐSURSRVLQJ"
3LHUFHௐLVௐWKHௐOHDGHUௐLQௐGRPHVWLFௐPDUNHWௐVKDUHௐRIௐILUHௐDSSDUDWXVௐௐ2VKNRVKௐ &RUSRUDWLRQௐLVௐWUDGHGௐRQௐWKHௐ1HZௐ<RUNௐ6WRFNௐ([FKDQJHௐVLQFHௐௐ)LQDQFLDOௐ LQIRUPDWLRQௐFDQௐEHௐREWDLQHGௐE\ௐYLVLWLQJௐWKHௐEHORZௐOLQNௐௐ KWWS
LQYHVWRURVKNRVKFRUSRUDWLRQFRPLQYHVWRUVILQDQFLDOLQIRUPDWLRQDQQXDODQGTXDUWHUO\ UHSRUWVGHIDXOWDVS[ௐௐ
)LUHௐ ௐ(PHUJHQF\ௐVHJPHQWௐ7KURXJKௐ3LHUFHௐWKHௐ&RPSDQ\ௐLVௐWKHௐOHDGLQJௐGRPHVWLFௐ GHVLJQHUௐDQGௐPDQXIDFWXUHUௐRIௐILUHௐDSSDUDWXVௐDVVHPEOHGௐRQௐFXVWRPௐFKDVVLVௐ GHVLJQHGௐDQGௐPDQXIDFWXUHGௐWRௐPHHWௐWKHௐVSHFLDOௐQHHGVௐRIௐILUHILJKWHUVௐ3LHUFHௐDOVRௐ GHVLJQVௐDQGௐPDQXIDFWXUHVௐILUHௐDSSDUDWXVௐDVVHPEOHGௐRQௐFRPPHUFLDOO\ௐDYDLODEOHௐ FKDVVLVௐZKLFKௐDUHௐSURGXFHGௐIRUௐPXOWLSOHௐHQGFXVWRPHUௐDSSOLFDWLRQVௐ3LHUFH¶Vௐ HQJLQHHULQJௐH[SHUWLVHௐDOORZVௐLWௐWRௐGHVLJQௐLWVௐYHKLFOHVௐWRௐPHHWௐVWULQJHQWௐLQGXVWU\ௐ JXLGHOLQHVௐDQGௐJRYHUQPHQWௐUHJXODWLRQVௐIRUௐVDIHW\ௐDQGௐHIIHFWLYHQHVVௐ3LHUFHௐSULPDULO\ௐ VHUYHVௐGRPHVWLFௐPXQLFLSDOௐFXVWRPHUVௐEXWௐDOVRௐVHOOVௐILUHௐDSSDUDWXVௐWRௐWKHௐ'R'ௐ DLUSRUWVௐXQLYHUVLWLHVௐDQGௐODUJHௐLQGXVWULDOௐFRPSDQLHVௐDQGௐLQௐLQWHUQDWLRQDOௐPDUNHWVௐ 3LHUFH¶VௐKLVWRU\ௐRIௐLQQRYDWLRQௐUHVHDUFKௐDQGௐGHYHORSPHQWௐLQௐFRQVXOWDWLRQௐZLWKௐ ILUHILJKWHUVௐKDVௐUHVXOWHGௐLQௐDௐEURDGௐSURGXFWௐOLQHௐWKDWௐIHDWXUHVௐDௐZLGHௐUDQJHௐRIௐ LQQRYDWLYHௐKLJKTXDOLW\ௐFXVWRPௐDQGௐFRPPHUFLDOௐILUHILJKWLQJௐHTXLSPHQWௐZLWKௐDGYDQFHGௐ ILUHௐVXSSUHVVLRQௐFDSDELOLWLHVௐ,QௐDQௐHIIRUWௐWRௐEHௐDௐVLQJOHVRXUFHௐVXSSOLHUௐIRUௐLWVௐ FXVWRPHUVௐ3LHUFHௐRIIHUVௐDௐIXOOௐOLQHௐRIௐFXVWRPௐDQGௐFRPPHUFLDOௐILUHௐDSSDUDWXVௐDQGௐ HPHUJHQF\ௐYHKLFOHVௐLQFOXGLQJௐSXPSHUVௐDHULDOௐSODWIRUPௐODGGHUௐDQG WLOOHUௐWUXFNVௐWDQNHUVௐOLJKWௐPHGLXPௐDQGௐKHDY\GXW\ௐUHVFXHௐYHKLFOHVௐZLOGODQGௐURXJKௐ WHUUDLQௐUHVSRQVHௐYHKLFOHVௐPRELOHௐFRPPDQGௐDQGௐFRQWUROௐFHQWHUVௐERPEௐVTXDGௐ YHKLFOHVௐKD]DUGRXVௐPDWHULDOVௐFRQWUROௐYHKLFOHVௐDQGௐRWKHUௐHPHUJHQF\ௐUHVSRQVHௐYHKLFOHV 7KHௐ&RPSDQ\ௐWKURXJKௐ$LUSRUWௐ3URGXFWVௐLVௐDௐOHDGHUௐLQௐWKHௐGHVLJQௐDQGௐVDOHௐRIௐ $5))ௐYHKLFOHVௐWRௐGRPHVWLFௐDQGௐLQWHUQDWLRQDOௐDLUSRUWVௐ7KHVHௐKLJKO\ௐVSHFLDOL]HGௐ YHKLFOHVௐDUHௐUHTXLUHGௐWRௐEHௐLQௐVHUYLFHௐDWௐPRVWௐDLUSRUWVௐZRUOGZLGHௐWRௐVXSSRUWௐ FRPPHUFLDOௐDLUOLQHVௐLQௐWKHௐHYHQWௐRIௐDQௐHPHUJHQF\ௐ0DQ\ௐRIௐWKHௐODUJHVWௐDLUSRUWVௐLQௐ WKHௐ8QLWHGௐ6WDWHVௐLQFOXGLQJௐ/D*XDUGLDௐ,QWHUQDWLRQDOௐ$LUSRUWௐ-RKQௐ)ௐ.HQQHG\ௐ ,QWHUQDWLRQDOௐ$LUSRUWௐ2¶+DUHௐ,QWHUQDWLRQDOௐ$LUSRUWௐ'HQYHUௐ,QWHUQDWLRQDOௐ$LUSRUWௐ %DOWLPRUH:DVKLQJWRQௐ,QWHUQDWLRQDOௐ$LUSRUWௐ'DOODV)RUWௐ:RUWKௐ,QWHUQDWLRQDOௐ$LUSRUWௐ 7DPSDௐ,QWHUQDWLRQDOௐ$LUSRUWௐ3KLODGHOSKLDௐ,QWHUQDWLRQDOௐ$LUSRUWௐDQGௐ6DQௐ)UDQFLVFRௐ ,QWHUQDWLRQDOௐ$LUSRUWௐDUHௐVHUYHGௐE\ௐWKHௐ&RPSDQ\¶Vௐ$5))ௐYHKLFOHVௐ7KHௐ86ௐ JRYHUQPHQWௐDOVRௐPDLQWDLQVௐDௐIOHHWௐRIௐ$5))ௐYHKLFOHVௐWKDWௐDUHௐXVHGௐWRௐVXSSRUWௐPLOLWDU\ௐ RSHUDWLRQVௐWKURXJKRXWௐWKHௐZRUOGௐ,QWHUQDWLRQDOO\ௐWKHௐ&RPSDQ\¶VௐYHKLFOHVௐVHUYHௐDPRQJௐ RWKHUVௐ%HLMLQJௐ&KLQDௐDQGௐPRUHௐWKDQௐILIW\ௐRWKHUௐDLUSRUWVௐLQௐ&KLQD ௐ6LQJDSRUH
ௐ
,QGRQHVLD
ௐ4XHEHFௐ&DQDGD
ௐ$EXௐ'KDELௐ8$(
ௐDQGௐ%LUPLQJKDPௐ&DUGLIIௐ0DQFKHVWHUௐ
DQGௐ/LYHUSRROௐ8QLWHGௐ.LQJGRPௐ,QௐDGGLWLRQௐWKHௐ&RPSDQ\ௐKDVௐUHFHQWO\ௐGHOLYHUHGௐ $5))ௐYHKLFOHVௐWRௐDLUSRUWVௐLQௐ0H[LFRௐ-DSDQௐ(J\SW
1HSDOௐ,UDTௐDQGௐWKHௐ%ULWLVKௐ9LUJLQௐ,VODQGVௐ7KHௐ&RPSDQ\ௐEHOLHYHVௐWKDWௐWKHௐ SHUIRUPDQFHௐDQGௐUHOLDELOLW\ௐRIௐLWVௐ$5))ௐYHKLFOHVௐFRQWULEXWHௐWRௐWKHௐ&RPSDQ\¶VௐVWURQJௐ SRVLWLRQௐLQௐWKLVௐPDUNHW
7KHௐ&RPSDQ\ௐWKURXJKௐLWVௐ)URQWOLQHௐEUDQGௐLVௐDௐOHDGLQJௐPDQXIDFWXUHUௐV\VWHPௐ GHVLJQHUௐDQGௐLQWHJUDWRUௐRIௐEURDGFDVWௐYHKLFOHVௐLQFOXGLQJௐHOHFWURQLFௐILHOGௐSURGXFWLRQௐ WUDLOHUVௐVDWHOOLWHௐQHZVௐJDWKHULQJௐDQGௐHOHFWURQLFௐQHZVௐJDWKHULQJௐYHKLFOHVௐIRUௐ EURDGFDVWHUVௐDQGௐFRPPDQGௐWUXFNVௐIRUௐORFDOௐDQGௐIHGHUDOௐJRYHUQPHQWVௐDORQJௐZLWKௐ EHLQJௐDௐOHDGLQJௐVXSSOLHUௐRIௐPLOLWDU\ௐVLPXODWRUௐVKHOWHUVௐDQGௐWUDLOHUVௐXQGHUௐWKHௐ2VKNRVKௐ 6SHFLDOW\ௐ9HKLFOHVௐ
269
ௐEUDQGௐ7KHௐ&RPSDQ\¶VௐYHKLFOHVௐKDYHௐEHHQௐXVHGௐZRUOGZLGHௐ WRௐEURDGFDVWௐWKHௐ1)/ௐ6XSHUௐ%RZOௐWKHௐ),)$ௐ:RUOGௐ&XSௐDQGௐWKHௐ2O\PSLFV 

 :KDWௐLVௐ\RXUௐ&DQDGLDQௐPDUNHWௐVKDUHௐIRUௐWKHௐ
VROXWLRQVௐWKDWௐ\RXௐDUHௐSURSRVLQJ"
3LHUFHௐDORQJௐZLWKௐWKHLUௐVWURQJௐGHDOHUௐVDOHVௐDQGௐVHUYLFHௐQHWZRUNௐWKDWௐKDVௐGULYHQௐ LQFUHDVHௐ&DQDGLDQௐPDUNHWௐVKDUHௐ7KHௐ3LHUFHௐ&DQDGLDQௐGHDOHUௐFRQVLVWௐRIௐௐGHDOHUVௐ WKDWௐOHDGௐPXOWLSOHௐVHUYLFHௐORFDWLRQVௐௐ:HௐDOVRௐSDUWQHUௐZLWKௐ0$;,0(7$/ௐ,QFௐ OHYHUDJLQJௐWKHௐ0$;,ௐ6DEHUௐSURJUDPௐVLQFHௐௐDQGௐ86ௐ&RQWHQGHUௐVLQFHௐௐ (DFKௐ'HDOHUௐKDVௐDௐVLJQHGௐGHDOHUௐDJUHHPHQWௐWRௐVHOOௐ3LHUFHௐILUHௐDSSDUDWXVௐLQௐWKHௐ GHVLJQDWHGௐWHUULWRU\ௐDZDUGHGௐWRௐWKHPௐ7KH\ௐDUHௐ3ULPHௐRQௐFRQWUDFWVௐDQGௐDUHௐ VXSSRUWHGௐE\ௐWKHௐௐ3LHUFHௐHPSOR\HHV


 +DVௐ\RXUௐEXVLQHVVௐHYHUௐSHWLWLRQHGௐIRUௐ
EDQNUXSWF\ௐSURWHFWLRQ"ௐ,IௐVRௐH[SODLQௐLQௐGHWDLO
1R 

Bid Number: RFP 113021 Vendor Name: Pierce Manufacturing 













 

EXHIBIT 1 587
 +RZௐLVௐ\RXUௐRUJDQL]DWLRQௐEHVWௐGHVFULEHG
ௐLVௐ
LWௐDௐPDQXIDFWXUHUௐDௐGLVWULEXWRUGHDOHUUHVHOOHUௐ
RUௐDௐVHUYLFHௐSURYLGHU"ௐௐ$QVZHUௐZKLFKHYHUௐ
TXHVWLRQௐ
HLWKHUௐD
ௐRUௐE
ௐMXVWௐEHORZ
ௐEHVWௐ
DSSOLHVௐWRௐ\RXUௐRUJDQL]DWLRQ
D
ௐௐௐௐ,Iௐ\RXUௐFRPSDQ\ௐLVௐEHVWௐGHVFULEHGௐDVௐ
DௐGLVWULEXWRUGHDOHUUHVHOOHUௐ
RUௐVLPLODUௐHQWLW\
ௐ
SURYLGHௐ\RXUௐZULWWHQௐDXWKRUL]DWLRQௐWRௐDFWௐDVௐDௐ
GLVWULEXWRUGHDOHUUHVHOOHUௐIRUௐWKHௐPDQXIDFWXUHUௐ
RIௐWKHௐSURGXFWVௐSURSRVHGௐLQௐWKLVௐ5)3ௐ,Iௐ
DSSOLFDEOHௐLVௐ\RXUௐGHDOHUௐQHWZRUNௐ
LQGHSHQGHQWௐRUௐFRPSDQ\ௐRZQHG"
E
ௐௐௐௐ,Iௐ\RXUௐFRPSDQ\ௐLVௐEHVWௐGHVFULEHGௐDVௐ
DௐPDQXIDFWXUHUௐRUௐVHUYLFHௐSURYLGHUௐGHVFULEHௐ
\RXUௐUHODWLRQVKLSௐZLWKௐ\RXUௐVDOHVௐDQGௐVHUYLFHௐ
IRUFHௐDQGௐZLWKௐ\RXUௐGHDOHUௐQHWZRUNௐLQௐ
GHOLYHULQJௐWKHௐSURGXFWVௐDQGௐVHUYLFHVௐ
SURSRVHGௐLQௐWKLVௐ5)3ௐ$UHௐWKHVHௐLQGLYLGXDOVௐ
\RXUௐHPSOR\HHVௐRUௐWKHௐHPSOR\HHVௐRIௐDௐWKLUGௐ
SDUW\"
3LHUFHௐDQGௐ$LUSRUWௐ3URGXFWVௐDUHௐEHVWௐGHVFULEHGௐDVௐPDQXIDFWXUHUV 3LHUFHௐDQGௐ$LUSRUWௐ3URGXFWVௐDUHௐEHVWௐGHVFULEHGௐDVௐPDQXIDFWXUHUV 7KHௐ3LHUFHௐ'HDOHUௐQHWZRUNௐFRQVLVWVௐRIௐௐ86ௐEDVHGௐ'HDOHUVௐDQGௐௐ&DQDGLDQௐ EDVHGௐ'HDOHUVௐ(DFKௐ'HDOHUௐKDVௐDௐVLJQHGௐGHDOHUௐDJUHHPHQWௐWRௐVHOOௐ3LHUFHௐILUHௐ DSSDUDWXVௐLQௐWKHௐGHVLJQDWHGௐWHUULWRU\ௐDZDUGHGௐWRௐWKHPௐ7KH\ௐDUHௐ3ULPHௐRQௐFRQWUDFWVௐ DQGௐDUHௐVXSSRUWHGௐE\ௐWKHௐௐ3LHUFHௐHPSOR\HHVௐ7KHௐ&RPSDQ\ௐEHOLHYHVௐWKHௐ JHRJUDSKLFௐEUHDGWKௐVL]HௐDQGௐTXDOLW\ௐRIௐLWVௐ3LHUFHௐILUHௐDSSDUDWXVௐVDOHVௐDQGௐVHUYLFHௐ RUJDQL]DWLRQௐDUHௐFRPSHWLWLYHௐDGYDQWDJHVௐLQௐDௐPDUNHWௐFKDUDFWHUL]HGௐE\ௐDௐIHZௐODUJHௐ PDQXIDFWXUHUVௐDQGௐQXPHURXVௐVPDOOௐUHJLRQDOௐFRPSHWLWRUVௐ 3LHUFH¶VௐILUHௐDSSDUDWXVௐLVௐVROGௐWKURXJKௐDQௐH[WHQVLYHௐQHWZRUNௐRIௐLQGHSHQGHQWௐVDOHVௐ DQGௐVHUYLFHௐRUJDQL]DWLRQVௐZLWKௐRYHUௐௐKXQGUHGௐVDOHVௐUHSUHVHQWDWLYHVௐLQௐWKHௐ86ௐ DQGௐ&DQDGDௐZKLFKௐFRPELQHௐEURDGௐJHRJUDSKLFDOௐUHDFKௐZLWKௐKLJKௐIUHTXHQF\ௐRIௐ FRQWDFWௐZLWKௐILUHௐGHSDUWPHQWVௐDQGௐPXQLFLSDOௐJRYHUQPHQWௐRIILFLDOVௐ7KHVHௐVDOHVௐDQGௐ VHUYLFHௐRUJDQL]DWLRQVௐDUHௐVXSSRUWHGௐE\ௐSURGXFWௐDQGௐPDUNHWLQJௐVXSSRUWௐSURIHVVLRQDOVௐ DQGௐFRQWUDFWௐDGPLQLVWUDWRUVௐDWௐ3LHUFHௐௐ7KHௐ&RPSDQ\ௐEHOLHYHVௐKLJKௐIUHTXHQF\ௐRIௐ FRQWDFWௐDQGௐORFDOௐSUHVHQFHௐDUHௐLPSRUWDQWௐWRௐFXOWLYDWHௐPDMRUௐDQGௐW\SLFDOO\ௐLQIUHTXHQWௐ SXUFKDVHVௐLQYROYLQJௐWKHௐFLW\ௐRUௐWRZQௐFRXQFLOௐILUHௐGHSDUWPHQWௐSXUFKDVLQJௐILQDQFHௐDQGௐ PD\RUDOௐRIILFHVௐDPRQJௐRWKHUVௐWKDWௐPD\ௐSDUWLFLSDWHௐLQௐDௐILUHௐDSSDUDWXVௐELGௐDQGௐ VHOHFWLRQௐSURFHVVௐ$IWHUௐWKHௐVDOHௐ3LHUFH¶VௐQDWLRQZLGHௐORFDOௐSDUWVௐDQGௐVHUYLFHௐ FDSDELOLW\ௐLVௐDYDLODEOHௐWRௐKHOSௐPXQLFLSDOLWLHVௐPDLQWDLQௐSHDNௐUHDGLQHVVௐIRUௐWKLVௐYLWDOௐ PXQLFLSDOௐVHUYLFHௐ
2VKNRVKௐ$LUSRUWௐ3URGXFWVௐ
7KHௐ&RPSDQ\ௐPDUNHWVௐLWVௐ2VKNRVKEUDQGHGௐ$5))ௐYHKLFOHVௐWKURXJKௐDௐFRPELQDWLRQௐRIௐ GLUHFWௐVDOHVௐUHSUHVHQWDWLYHVௐGRPHVWLFDOO\ௐDQGௐDQௐH[WHQVLYHௐQHWZRUNௐRIௐUHSUHVHQWDWLYHVௐ DQGௐGLVWULEXWRUVௐLQௐLQWHUQDWLRQDOௐPDUNHWVௐLQFOXGLQJௐ&DQDGDௐ&HUWDLQௐRIௐWKHVHௐ LQWHUQDWLRQDOௐUHSUHVHQWDWLYHVௐDQGௐGLVWULEXWRUVௐDOVRௐKDQGOHௐ3LHUFHௐSURGXFWVௐDQGௐZLOOௐ IROORZௐWKHௐVDPHௐSURFHVVௐDVௐQRWHGௐDERYHௐௐ)RUௐVHUYLFHௐZHௐVXSSRUWௐERWKௐZLWKௐ LQWHUQDOௐVHUYLFHௐVXSSRUWௐZKLFKௐLVௐDYDLODEOHௐௐYLDௐRXUௐVXSSRUWௐOLQHௐDWௐ ௐDQGௐH[WHUQDOௐVDOHVௐUHSUHVHQWDWLYHVௐ
5HIHUௐWRௐௐ3LHUFHௐ$LUSRUWௐ0DQXIDFWXUHUௐ3URGXFWVSGIௐLQௐ&RPSDQ\ௐ,QIRUPDWLRQௐDQGௐ )LQDQFLDOௐ6WUHQJWKௐIROGHUௐIRUௐDQௐRYHUYLHZௐRIௐRXUௐPDQXIDFWXULQJௐFDSDELOLWLHVௐDQGௐ SURGXFWௐRIIHULQJV


Bid Number: RFP 113021 Vendor Name: Pierce Manufacturing 













 

EXHIBIT 1 588
 ,IௐDSSOLFDEOHௐSURYLGHௐDௐGHWDLOHGௐH[SODQDWLRQௐ
RXWOLQLQJௐWKHௐOLFHQVHVௐDQGௐFHUWLILFDWLRQVௐWKDWௐ
DUHௐERWKௐUHTXLUHGௐWRௐEHௐKHOGௐDQGௐDFWXDOO\ௐ
KHOGௐE\ௐ\RXUௐRUJDQL]DWLRQௐ
LQFOXGLQJௐWKLUGௐ
SDUWLHVௐDQGௐVXEFRQWUDFWRUVௐWKDWௐ\RXௐXVH
ௐLQௐ
SXUVXLWௐRIௐWKHௐEXVLQHVVௐFRQWHPSODWHGௐE\ௐWKLVௐ
5)3
3LHUFHௐ0DQXIDFWXULQJௐ,QFௐKROGVௐVWDWHௐOLFHQVLQJௐIRUௐ6DOHVௐ0DQXIDFWXULQJௐ0RWRUௐ 9HKLFOHVௐDQGௐGHDOHUௐOLFHQVHௐXVHGௐDFFRUGDQFHௐWRௐWKHௐVWDWHௐODZVௐ7KHௐ3LHUFHௐ'HDOHUௐ QHWZRUNௐOLFHQVHVௐLQGHSHQGHQWO\ௐKROGVௐDVௐUHTXLUHGௐE\ௐODZௐLQௐWKHௐVWDWHௐLQௐZKLFKௐWKH\ௐ VHOOௐௐ$LUSRUWௐ3URGXFWVௐKROGVௐPDQXIDFWXUHU¶VௐOLFHQVHௐZKHUHௐUHTXLUHGௐௐ :HௐDOVRௐKROGௐRXUௐ9HQGRUVௐDFFRXQWDEOHௐWRௐWKHௐXWPRVWௐVWDQGDUGVௐ%H\RQGௐ,62ௐ FHUWLILFDWLRQVௐDQGௐFRPSOLDQFHௐZHௐUHTXLUHௐRXUௐVXSSO\ௐFKDLQௐRIௐPDMRUௐFRPSRQHQWVௐWRௐ REWDLQௐDௐVFRUHௐRIௐௐRUௐDERYHௐRQௐDௐVXSSOLHUௐTXDOLW\ௐDXGLWௐSHUIRUPHGௐE\ௐ2VKNRVKௐ &RUSRUDWLRQௐVXSSOLHUௐTXDOLW\
,62ௐ

ௐ&HUWLILFDWLRQ
ௐ
3LHUFHௐ0DQXIDFWXULQJௐ,QFௐZDVௐWKHௐILUVWௐVLQJOHVRXUFHௐPDQXIDFWXUHUௐRIௐFXVWRPௐILUHௐ DSSDUDWXVௐLQௐ1RUWKௐ$PHULFDௐWRௐDFKLHYHௐ,62ௐ
ௐFHUWLILFDWLRQௐ3LHUFHௐKDVௐDFKLHYHGௐ
,62ௐ

ௐFHUWLILFDWLRQௐZKLFKௐFRYHUVௐDOOௐDVSHFWVௐRIௐRXUௐEXVLQHVVௐOLIHௐF\FOHௐIURPௐ HQJLQHHULQJௐDQGௐPDQXIDFWXULQJௐWRௐFXVWRPHUௐVHUYLFHௐ
,62ௐ
ௐFHUWLILFDWLRQௐGHPRQVWUDWHVௐDௐFRPSDQ\
VௐFRPPLWPHQWௐWRௐTXDOLW\ௐ7RௐNHHSௐ
WKHLUௐ,62ௐ
ௐUHJLVWHUHGௐVWDWXVௐFRPSDQLHVௐDUHௐUHDXGLWHGௐWZLFHௐSHUௐ\HDUௐWKURXJKௐ WKLUGSDUW\ௐYHULILFDWLRQௐWRௐSURYHௐWKH\ௐDUHௐPDLQWDLQLQJௐJRRGௐSUDFWLFHVௐ,62ௐ ௐ
FHUWLILFDWLRQௐIXUWKHUௐDVVXUHVௐFXVWRPHUVௐWKDWௐDௐIXQGDPHQWDOௐTXDOLW\ௐV\VWHPௐLVௐLQௐSODFHௐ ,W
VௐDௐVROLGௐIRXQGDWLRQௐIRUௐFRQWLQXRXVௐLPSURYHPHQWௐDOZD\VௐVWULYLQJௐWRௐJHWௐHYHQௐEHWWHUௐ $Qௐ,62FHUWLILHGௐPDQXIDFWXUHUௐOLNHௐ3LHUFHௐDFFHSWVௐQRWKLQJௐEXWௐWKHௐEHVWௐIURPௐLWVௐ VXSSOLHUVௐ3LHUFHௐDVNVௐLWVௐVXSSOLHUVௐWRௐPHHWௐPDQ\ௐRIௐWKHௐVDPHௐVWULQJHQWௐTXDOLW\ௐ UHTXLUHPHQWVௐDQGௐZRUNVௐZLWKௐWKHPௐWRௐLPSURYHௐWKHLUௐTXDOLW\ௐV\VWHPVௐDVௐZHOO 5HIHUௐWRௐௐ,62ௐ
ௐ3LHUFHௐ0IJௐDQGௐHQWLWLHVSGIௐLQௐ)LQDQFLDOௐ6WUHQJWKௐDQGௐ 6WDELOLW\ௐIROGHUௐIRUௐFHUWLILFDWHௐ
8/8/&

3LHUFHௐLVௐWKHௐILUVWௐILUHௐDSSDUDWXVௐPDQXIDFWXUHUௐWRௐEHௐERWKௐWKLUGௐSDUW\ௐFHUWLILHGௐWRௐ 1)3$ௐ
ௐHGLWLRQௐDQGௐ8/&ௐOLVWHGௐWRௐ&DQDGDௐ8/&6ௐVWDQGDUG 7KLUGௐ3DUW\ௐ9HKLFOHௐ,QVSHFWLRQௐ3URJUDPௐE\ௐ8QGHUZULWHUVௐ/DERUDWRULHVௐWRௐHQVXUHௐRXUௐ SURGXFWVௐDUHௐௐ1)3$ௐFRPSOLDQWௐWRௐ
ௐVWDQGDUGVௐௐ7KHௐFHUWLILFDWLRQௐLQFOXGHVௐ
DOOௐGHVLJQௐSURGXFWLRQௐRSHUDWLRQDOௐDQGௐSHUIRUPDQFHௐWHVWLQJௐRIௐWKHௐFRPSOHWHௐ DSSDUDWXVௐ$OOௐSURGXFWVௐPXVWௐSDVVௐDOOௐWHVWVௐEHIRUHௐDௐWUXFNௐLVௐUHOHDVHGௐLQWRௐ&DQDGDௐ 7KLVௐFRPPLWPHQWௐWRௐTXDOLW\ௐDSSOLHVௐWRௐWUXFNVௐVROGௐLQௐWKHௐ86ௐDVௐZHOO 5HIHUௐWRௐௐ6DPSOHௐ8/ௐ&HUWVௐ
ௐ3XPSௐ/LQHௐ9ROWDJHௐ$HULDOௐ&HUWSGIௐLQௐ
)LQDQFLDOௐ6WUHQJWKௐDQGௐ6WDELOLW\ௐIROGHUௐIRUௐVDPSOHௐFHUWLILFDWH ,62ௐ
ௐ&HUWLILFDWLRQ
ௐ
2XUௐ1HHQDKௐIDFLOLW\ௐLVௐDOVRௐ,62ௐ
ௐFHUWLILHGௐIRUௐRXUௐ(QYLURQPHQWDOௐ
0DQDJHPHQWௐ6\VWHPௐௐ9DULRXVௐ3LHUFHௐDQGௐ$LUSRUWௐ3URGXFWVௐYHKLFOHVௐDUHௐ PDQXIDFWXUHGௐLQௐWKLVௐVSDFHௐ
5HIHUௐWRௐௐ,62ௐௐ2VKNRVKௐ$LUSRUWௐ3URGXFWVSGIௐLQௐ)LQDQFLDOௐ6WUHQJWKௐDQGௐ 6WDELOLW\ௐIROGHUௐIRUௐFHUWLILFDWH


 3URYLGHௐDOOௐ³6XVSHQVLRQௐRUௐ'HEDUPHQW´ௐ
LQIRUPDWLRQௐWKDWௐKDVௐDSSOLHGௐWRௐ\RXUௐ
RUJDQL]DWLRQௐGXULQJௐWKHௐSDVWௐWHQௐ\HDUV
1HLWKHUௐ2VKNRVKௐ&RUSRUDWLRQௐRUௐVXEVLGLDU\ௐVXFKௐDVௐ3LHUFHௐ0DQXIDFWXULQJௐDQGௐ$LUSRUWௐ 3URGXFWVௐKDYHௐVXVSHQVLRQௐRUௐGHEDUPHQWௐWKDWௐDSSOLHVௐZLWKLQௐWKHௐSDVWௐௐ\HDUV 

7DEOH
,QGXVWU\5HFRJQLWLRQ 0DUNHWSODFH6XFFHVV
/LQH
,WHP 4XHVWLRQ 5HVSRQVH

 'HVFULEHௐDQ\ௐUHOHYDQWௐLQGXVWU\ௐDZDUGVௐRUௐ
UHFRJQLWLRQௐWKDWௐ\RXUௐFRPSDQ\ௐKDVௐUHFHLYHGௐ
LQௐWKHௐSDVWௐILYHௐ\HDUV
2VKNRVKௐ&RUSRUDWLRQௐௐLVௐKRQRUHGௐWRௐEHௐQDPHGௐDQGௐUHFRJQL]HGௐIRUௐWKHௐIROORZLQJௐ DZDUGVௐDQGௐUHFRJQLWLRQVௐ
:RUOG¶Vௐ0RVWௐ(WKLFDOௐ&RPSDQLHVௐLQௐௐௐௐ ௐௐDQGௐௐ
2VKNRVKௐLVௐRQHௐRIௐRQO\ௐௐFRPSDQLHVௐUHSUHVHQWLQJௐௐLQGXVWU\ௐVHFWRUVௐLQௐ ௐ
FRXQWULHVௐRQௐILYHௐFRQWLQHQWVௐQDPHGௐWRௐWKLVௐSUHVWLJLRXVௐOLVWௐ:HௐZHUHௐWKHௐRQO\ௐ FRPSDQ\ௐVHOHFWHGௐLQௐWKHௐ³7UXFNVௐDQGௐ2WKHUௐ9HKLFOHV´ௐFDWHJRU\ௐXQGHUVFRULQJௐRXUௐ FRPPLWPHQWௐWRௐOHDGLQJௐHWKLFDOௐEXVLQHVVௐVWDQGDUGVௐDQGௐSUDFWLFHVௐ7KLVௐDFKLHYHPHQWௐ LVௐRQO\ௐSRVVLEOHௐZLWKௐDௐFRPPLWPHQWௐWRௐVXVWDLQDELOLW\ௐFRQQHFWLQJௐZLWKௐRXUௐ FRPPXQLWLHVௐDQGௐVWURQJௐHWKLFDOௐFXOWXUHௐDQGௐWHDPௐPHPEHUVௐZKRௐEHOLHYHௐLQௐGRLQJௐWKHௐ ULJKWௐWKLQJௐ
/LQN
ௐKWWSV
LQYHVWRUVRVKNRVKFRUSFRPQHZVQHZVGHWDLOV2VKNRVK&RUSRUDWLRQ QDPHGRQHRIWKH:RUOGV0RVW(WKLFDO&RPSDQLHVIRUVL[WKFRQVHFXWLYH\HDUGHIDXOWDVS[ )25781(¶Vௐ:RUOG¶Vௐ0RVWௐ$GPLUHGௐ&RPSDQLHVௐLQௐ
ௐDQGௐௐ2VKNRVKௐ
&RUSRUDWLRQௐLVௐRQHௐRIௐௐFRPSDQLHVௐWRௐDFKLHYHௐWKLVௐKRQRUௐDVௐUDQNHGௐE\ௐLQGXVWU\ௐ SHHUVௐKLJKOLJKWLQJௐVRPHௐRIௐWKHௐPRVWௐUHVSHFWHGௐDQGௐVXFFHVVIXOௐFRPSDQLHVௐIURPௐ DURXQGௐWKHௐZRUOGௐKWWSV
LQYHVWRUVRVKNRVKFRUSFRPQHZVQHZVGHWDLOV2VKNRVK &RUSRUDWLRQQDPHGRQHRIWKH:RUOGV0RVW$GPLUHG&RPSDQLHVE\ )25781(GHIDXOWDVS[
Bid Number: RFP 113021 Vendor Name: Pierce Manufacturing 













 

EXHIBIT 1 589
,QௐௐDQGௐௐWKHௐFRPSDQ\ௐZDVௐDZDUGHGௐRQHௐRIௐ$PHULFD¶Vௐ0RVWௐ5HVSRQVLEOHௐ &RPSDQLHVௐE\ௐ1HZVZHHNௐௐ2VKNRVKௐKDVௐHDUQHGௐWKLVௐDZDUGௐIRUௐWZRௐFRQVHFXWLYHௐ \HDUVௐDQGௐLVௐUDQNHGௐ
ௐRXWௐRIௐ

ௐFRPSDQLHVௐRQௐWKHௐOLVWௐ$PHULFD¶Vௐ0RVWௐ
5HVSRQVLEOHௐ&RPSDQLHVௐZHUHௐGHILQHGௐEDVHGௐRQௐNH\ௐSHUIRUPDQFHௐLQGLFDWRUVௐDURXQGௐ HQYLURQPHQWDOௐVRFLDOௐDQGௐFRUSRUDWHௐJRYHUQDQFHௐDUHDVௐௐ)RUௐPRUHௐLQIRௐSOHDVHௐUHIHUௐ WRௐWKHௐOLQNௐEHORZ
ௐKWWSV
ZZZRVKNRVKFRUSFRPHQQHZVPRVWUHVSRQVLEOH

QHZVZHHN
2VKNRVKௐ&RUSRUDWLRQௐZDVௐQDPHGௐDௐ0LOLWDU\ௐ)ULHQGO\ௐ&RPSDQ\ௐLQௐௐௐ ௐ
ௐDQGௐௐ%HLQJௐQDPHGௐDௐ0LOLWDU\ௐ)ULHQGO\ௐ&RPSDQ\ௐKLJKOLJKWVௐRXUௐ FRPPLWPHQWௐWRௐFDULQJௐIRUௐRXUௐWHDPௐPHPEHUௐDQGௐKDYLQJௐDௐFXOWXUHௐZKHUHௐYHWHUDQVௐ FDQௐWKULYHௐௐ3OHDVHௐUHIHUHQFHௐWKHௐOLQNௐIRUௐDGGLWLRQDOௐGHWDLO ௐ
KWWSV
ZZZRVKNRVKFRUSFRPHQQHZVௐ
2VKNRVKௐ&RUSRUDWLRQௐKDVௐEHHQௐOLVWHGௐRQௐWKHௐ'RZௐ-RQHVௐ6XVWDLQDELOLW\ௐ:RUOGௐ,QGH[ௐ LQௐ
ௐௐDQGௐௐ3OHDVHௐUHYLHZௐWKHௐOLQNௐEHORZௐIRUௐDGGLWLRQDOௐLQIRௐ KWWSV
LQYHVWRUVRVKNRVKFRUSFRPQHZVQHZVGHWDLOV2VKNRVK&RUSRUDWLRQ1DPHG WRWKH'RZ-RQHV6XVWDLQDELOLW\:RUOG,QGH[IRU6HFRQG&RQVHFXWLYH<HDUGHIDXOWDVS[ 2VKNRVKௐ&RUSRUDWLRQௐௐLVௐKRQRUHGௐWRௐEHௐQDPHGௐDQGௐUHFRJQL]HGௐIRUௐWKHௐIROORZLQJௐ DZDUGVௐDQGௐUHFRJQLWLRQVௐ
:RUOG¶Vௐ0RVWௐ(WKLFDOௐ&RPSDQLHVௐLQௐௐௐௐ ௐௐDQGௐௐ
2VKNRVKௐLVௐRQHௐRIௐRQO\ௐௐFRPSDQLHVௐUHSUHVHQWLQJௐௐLQGXVWU\ௐVHFWRUVௐLQௐ ௐ
FRXQWULHVௐRQௐILYHௐFRQWLQHQWVௐQDPHGௐWRௐWKLVௐSUHVWLJLRXVௐOLVWௐ:HௐZHUHௐWKHௐRQO\ௐ FRPSDQ\ௐVHOHFWHGௐLQௐWKHௐ³7UXFNVௐDQGௐ2WKHUௐ9HKLFOHV´ௐFDWHJRU\ௐXQGHUVFRULQJௐRXUௐ FRPPLWPHQWௐWRௐOHDGLQJௐHWKLFDOௐEXVLQHVVௐVWDQGDUGVௐDQGௐSUDFWLFHVௐ7KLVௐDFKLHYHPHQWௐ LVௐRQO\ௐSRVVLEOHௐZLWKௐDௐFRPPLWPHQWௐWRௐVXVWDLQDELOLW\ௐFRQQHFWLQJௐZLWKௐRXUௐ FRPPXQLWLHVௐDQGௐVWURQJௐHWKLFDOௐFXOWXUHௐDQGௐWHDPௐPHPEHUVௐZKRௐEHOLHYHௐLQௐGRLQJௐWKHௐ ULJKWௐWKLQJௐ
/LQN
ௐKWWSV
LQYHVWRUVRVKNRVKFRUSFRPQHZVQHZVGHWDLOV2VKNRVK&RUSRUDWLRQ QDPHGRQHRIWKH:RUOGV0RVW(WKLFDO&RPSDQLHVIRUVL[WKFRQVHFXWLYH\HDUGHIDXOWDVS[ )25781(¶Vௐ:RUOG¶Vௐ0RVWௐ$GPLUHGௐ&RPSDQLHVௐLQௐ
ௐDQGௐௐ2VKNRVKௐ
&RUSRUDWLRQௐLVௐRQHௐRIௐௐFRPSDQLHVௐWRௐDFKLHYHௐWKLVௐKRQRUௐDVௐUDQNHGௐE\ௐLQGXVWU\ௐ SHHUVௐKLJKOLJKWLQJௐVRPHௐRIௐWKHௐPRVWௐUHVSHFWHGௐDQGௐVXFFHVVIXOௐFRPSDQLHVௐIURPௐ DURXQGௐWKHௐZRUOGௐKWWSV
LQYHVWRUVRVKNRVKFRUSFRPQHZVQHZVGHWDLOV2VKNRVK &RUSRUDWLRQQDPHGRQHRIWKH:RUOGV0RVW$GPLUHG&RPSDQLHVE\ )25781(GHIDXOWDVS[
,QௐௐDQGௐௐWKHௐFRPSDQ\ௐZDVௐDZDUGHGௐRQHௐRIௐ$PHULFD¶Vௐ0RVWௐ5HVSRQVLEOHௐ &RPSDQLHVௐE\ௐ1HZVZHHNௐௐ2VKNRVKௐKDVௐHDUQHGௐWKLVௐDZDUGௐIRUௐWZRௐFRQVHFXWLYHௐ \HDUVௐDQGௐLVௐUDQNHGௐ
ௐRXWௐRIௐ

ௐFRPSDQLHVௐRQௐWKHௐOLVWௐ$PHULFD¶Vௐ0RVWௐ
5HVSRQVLEOHௐ&RPSDQLHVௐZHUHௐGHILQHGௐEDVHGௐRQௐNH\ௐSHUIRUPDQFHௐLQGLFDWRUVௐDURXQGௐ HQYLURQPHQWDOௐVRFLDOௐDQGௐFRUSRUDWHௐJRYHUQDQFHௐDUHDVௐௐ)RUௐPRUHௐLQIRௐSOHDVHௐUHIHUௐ WRௐWKHௐOLQNௐEHORZ
ௐKWWSV
ZZZRVKNRVKFRUSFRPHQQHZVPRVWUHVSRQVLEOH

QHZVZHHN
2VKNRVKௐ&RUSRUDWLRQௐZDVௐQDPHGௐDௐ0LOLWDU\ௐ)ULHQGO\ௐ&RPSDQ\ௐLQௐௐௐ ௐ
ௐDQGௐௐ%HLQJௐQDPHGௐDௐ0LOLWDU\ௐ)ULHQGO\ௐ&RPSDQ\ௐKLJKOLJKWVௐRXUௐ FRPPLWPHQWௐWRௐFDULQJௐIRUௐRXUௐWHDPௐPHPEHUௐDQGௐKDYLQJௐDௐFXOWXUHௐZKHUHௐYHWHUDQVௐ FDQௐWKULYHௐௐ3OHDVHௐUHIHUHQFHௐWKHௐOLQNௐIRUௐDGGLWLRQDOௐGHWDLO ௐ
KWWSV
ZZZRVKNRVKFRUSFRPHQQHZVௐ
2VKNRVKௐ&RUSRUDWLRQௐKDVௐEHHQௐOLVWHGௐRQௐWKHௐ'RZௐ-RQHVௐ6XVWDLQDELOLW\ௐ:RUOGௐ,QGH[ௐ LQௐ
ௐௐDQGௐௐ3OHDVHௐUHYLHZௐWKHௐOLQNௐEHORZௐIRUௐDGGLWLRQDOௐLQIRௐ KWWSV
LQYHVWRUVRVKNRVKFRUSFRPQHZVQHZVGHWDLOV2VKNRVK&RUSRUDWLRQ1DPHG WRWKH'RZ-RQHV6XVWDLQDELOLW\:RUOG,QGH[IRU6HFRQG&RQVHFXWLYH<HDUGHIDXOWDVS[ 2VKNRVKௐZDVௐQDPHGௐRQHௐRIௐWKHௐ³:RUOG¶Vௐ%HVWௐ(PSOR\HUV´ௐE\ௐ)RUEHVௐLQௐௐ7KHௐ ௐUHVXOWVௐLQFOXGHGௐௐPXOWLQDWLRQDOௐDQGௐODUJHௐFRUSRUDWLRQVௐDFURVVௐௐFRXQWULHVௐ 2VKNRVKௐLVௐUDQNHGௐௐRXWௐRIௐ
3OHDVHௐUHIHUௐWRௐWKHௐOLQN
ௐKWWSV
ZZZRVKNRVKFRUSFRPHQQHZVIRUEHV
2VKNRVKௐLVௐRQHௐRIௐ%DUURQ¶Vௐௐ0RVWௐ6XVWDLQDEOHௐ&RPSDQLHVௐIRUௐWKHௐ\HDUVௐ ௐ
ௐDQGௐௐ3OHDVHௐUHYLHZௐWKHௐOLQNௐIRUௐDGGLWLRQDOௐLQIRUPDWLRQௐ KWWSV
LQYHVWRUVRVKNRVKFRUSFRPQHZVQHZVGHWDLOV2VKNRVK&RUSRUDWLRQVIRFXV RQVXVWDLQDELOLW\HDUQVUHFRJQLWLRQIURP%DUURQVDQG63*OREDOGHIDXOWDVS[ 3LHUFH¶VௐIRFXVௐRQௐHQHUJ\ௐHIILFLHQF\ௐLVௐIRFXVHGௐRQௐEHLQJௐJRRGௐVWHZDUGVௐRIௐFRPSDQ\ௐ UHVRXUFHVௐEXGJHWVௐDQGௐWKHௐFRPSDQ\¶VௐHFRORJLFDOௐIRRWSULQWௐ7KLVௐHDUQHGௐWKHPௐWKHௐ UHFRJQLWLRQௐIRUௐ)RFXVௐRQௐ(QHUJ\ௐௐ(QHUJ\ௐ(IILFLHQF\ௐ([FHOOHQFHௐ$ZDUG KWWSV
ZZZSLHUFHPIJFRPSLHUFHEORJSLHUFHUHFRJQL]HGZLWKIRFXVRQHQHUJ\H[FHOOHQFH DZDUG


Bid Number: RFP 113021 Vendor Name: Pierce Manufacturing 













 

EXHIBIT 1 590
3LHUFH DOVR $FKLHYHG 758(
7RWDO 5HVRXUFH 8VH DQG (IILFLHQF\
=HUR :DVWH
&HUWLILFDWLRQௐDWௐWKHௐ*ROGௐOHYHOௐ758(ௐFHUWLILFDWLRQௐLVௐDGPLQLVWHUHGௐE\ௐ*UHHQௐ %XVLQHVVௐ&HUWLILFDWLRQௐ,QFௐ
*%&,
ௐDQௐRUJDQL]DWLRQௐWKDWௐLQGHSHQGHQWO\ௐUHFRJQL]HVௐ
H[FHOOHQFHௐLQௐJUHHQௐEXVLQHVVௐLQGXVWU\ௐSHUIRUPDQFHௐDQGௐSUDFWLFHௐJOREDOO\ ௐ6WHUOLQJௐ0DQXIDFWXULQJௐ%XVLQHVVௐ([FHOOHQFHௐ$ZDUGௐௐ)ORULGDௐIDFLOLW\ௐKDVௐEHHQௐ DZDUGHGௐWKHௐௐ6WHUOLQJௐ0DQXIDFWXULQJௐ%XVLQHVVௐ([FHOOHQFHௐ$ZDUGௐDWௐWKHௐ*ROGௐ /HYHOௐ7KLVௐDZDUGௐZHQWௐRXWௐWRௐWKHௐFRPSDQ\ௐWKDWௐZDVௐIRXQGௐWRௐEHௐDௐKLJKௐSHUIRUPLQJௐ PDQXIDFWXUHUௐLQௐVHYHQௐFDWHJRULHVௐ3LHUFHௐ%UDGHQWRQௐGHPRQVWUDWHGௐRXWVWDQGLQJௐ OHDGHUVKLSௐDQGௐPDQDJHPHQWௐV\VWHPVௐWRௐPHHWௐWKHௐQHHGௐRIௐFXVWRPHUVௐDQGௐ VWDNHKROGHUVௐKWWSV
ZZZIDFHERRNFRP3LHUFHSRVWV

3LHUFHௐZDVௐDZDUGHGௐWKHௐ³$ERYHௐDQGௐ%H\RQGௐ$ZDUG´ௐE\ௐ(6*5ௐ$XJXVWௐRIௐௐ 3LHUFHௐZDVௐௐRIௐௐODUJHௐFRPSDQLHVௐLQௐ:LVFRQVLQௐUHFRJQL]HGௐIRUௐWKHLUௐRXWVWDQGLQJௐ VXSSRUWௐRIௐRXUௐ*XDUGௐDQGௐ5HVHUYHௐIRUFHVௐ
2VKNRVKௐ&RUSRUDWLRQௐKDVௐEHHQௐQDPHGௐRQHௐRIௐWKHௐ³%HVWௐ0DQDJHGௐ&RPSDQLHV´ௐE\ௐ WKHௐ:DOOௐ6WUHHWௐ-RXUQDOௐLQௐௐDQGௐ
ௐௐ3OHDVHௐYLVLWௐWKHௐOLQNௐIRUௐDGGLWLRQDOௐ
GHWDLO
ௐKWWSV
ZZZEXVLQHVVZLUHFRPQHZVKRPH


HQ2VKNRVK
&RUSRUDWLRQ1DPHG2QHRIWKH(
&%HVW0DQDJHG&RPSDQLHVRI

(
'E\WKH:DOO6WUHHW-RXUQDO
,62ௐ
ௐ(QYLURQPHQWDOௐ0DQDJHPHQWௐ6\VWHP
7RௐIXUWKHUௐVROLGLI\ௐDQGௐVWDQGDUGL]HௐRXUௐHQYLURQPHQWDOௐSHUIRUPDQFHௐ3LHUFHௐ 0DQXIDFWXULQJௐDQGௐWKHௐ$LUSRUWௐ3URGXFWVௐ*URXSௐDUHௐLQௐWKHௐILUVWௐGRPHVWLFDOO\ௐௐRIௐ IRUPDOL]LQJௐDQௐ(QYLURQPHQWDOௐ0DQDJHPHQWௐ6\VWHPௐIRUௐRXUௐ1HHQDKௐPDQXIDFWXULQJௐ IDFLOLW\ௐLQௐDFFRUGDQFHௐZLWKௐ,62ௐ
ௐIRUௐDOOௐRIௐ2VKNRVKௐ&RUSRUDWLRQௐ
5HFRJQL]HGௐE\ௐ5REHFR6$0ௐZLWKௐWKHௐ,QGXVWU\ௐ0RYHUௐ$ZDUGௐIRUௐFULWLFDOௐVWHSVௐWDNHQௐ WRௐSURSHOௐFRUSRUDWHௐVXVWDLQDELOLW\ௐE\ௐPHDVXULQJௐLPSDFWௐDQGௐGLVFORVLQJௐUHVXOWVௐ 2VKNRVKௐ&RUSRUDWLRQௐKDVௐDFKLHYHGௐPDQ\ௐDZDUGVௐWKURXJKRXWௐWKHௐ\HDUVௐ0DQ\ௐRIௐWKHௐ DZDUGVௐKLJKOLJKWௐVSHFLILFௐVXEVLGLDULHVௐVXFKௐDVௐ3LHUFHௐDQGௐ$LUSRUWௐ3URGXFWVௐ7KHUHௐ DUHௐPDQ\ௐPRUHௐWKDWௐKDYHௐQRWௐEHHQௐLQFRUSRUDWHGௐEXWௐDUHௐLQFRUSRUDWHGௐRQௐRXUௐ ZHEVLWHVௐ:HௐDUHௐSURXGௐDQGௐZRUNௐKDUGௐWRௐPDLQWDLQௐWKHVHௐDFKLHYHPHQWVௐ 5HIHUௐWRௐௐ758(ௐ&(576,'ௐSGIௐLQௐ$GGLWLRQDOௐ'RFXPHQWVௐIROGHUௐIRUௐ FHUWLILFDWH

:KDWௐSHUFHQWDJHௐRIௐ\RXUௐVDOHVௐDUHௐWRௐWKHௐ
JRYHUQPHQWDOௐVHFWRUௐLQௐWKHௐSDVWௐWKUHHௐ\HDUV
2VKNRVKௐKDVௐJUHDWௐUHODWLRQVKLSௐZLWKௐYDULRXVௐJRYHUQPHQWDOௐVHFWRUVௐWKURXJKRXWௐWKHௐ RUJDQL]DWLRQௐ:HௐDUHௐDௐSXEOLFO\ௐWUDGHGௐFRPSDQ\ௐWKHUHIRUHௐWKHௐLQIRUPDWLRQௐDYDLODEOHௐ GRHVௐQRWௐLQFOXGHௐVSHFLILFௐVDOHVௐGHWDLO


 :KDWௐSHUFHQWDJHௐRIௐ\RXUௐVDOHVௐDUHௐWRௐWKHௐ
HGXFDWLRQௐVHFWRUௐLQௐWKHௐSDVWௐWKUHHௐ\HDUV
3LHUFHௐDQGௐ$LUSRUWௐRQௐRFFDVLRQௐZLOOௐVHOOௐWRௐHGXFDWLRQௐVHFWRUVௐVXFKௐDVௐ8QLYHUVLWLHVௐ &ROOHJHVௐ+LJKௐ6FKRROVௐRUௐ)LUHௐVFKRROVௐௐ7KHௐPDUNHWௐIRUௐRXUௐSURGXFWௐLQௐWKLVௐJURXSௐ LVௐOLPLWHG


 /LVWௐDQ\ௐVWDWHௐSURYLQFLDOௐRUௐFRRSHUDWLYHௐ
SXUFKDVLQJௐFRQWUDFWVௐWKDWௐ\RXௐKROGௐ:KDWௐLVௐ
WKHௐDQQXDOௐVDOHVௐYROXPHௐIRUௐHDFKௐRIௐWKHVHௐ
FRQWUDFWVௐRYHUௐWKHௐSDVWௐWKUHHௐ\HDUV"
3LHUFHௐ0DQXIDFWXULQJௐSDUWLFLSDWHVௐLQௐQDWLRQZLGHௐDQGௐVWDWHOHYHOௐFRQWUDFWVௐ$OOௐ SURJUDPVௐDUHௐDOLJQHGௐWRௐRIIHUௐWKHௐEHVWௐVROXWLRQVௐRQௐDௐFRQVLVWHQWௐSODWIRUPௐ&RQWUDFWVௐ ZLWKௐDQௐDVWHULVNௐ

ௐDOVRௐKDYHௐFRQWUDFWVௐKHOGௐE\ௐ$LUSRUWௐ3URGXFWVௐ
ௐௐௐௐ6RXUFHZHOO
ௐ
ௐௐௐௐ+*$&
ௐ
ௐௐௐௐ1$632ௐ9DOXHௐ3RLQWௐ
ௐௐௐௐ133*RY
ௐௐௐௐ/DPDV
ௐௐௐௐ%X\%RDUG
ௐௐௐௐ)ORULGDௐ6KHUULII¶V
ௐௐௐௐ2KLRௐ6WDWHௐ

ௐௐௐௐ&RVWDUV


 /LVWௐDQ\ௐ*6$ௐFRQWUDFWVௐRUௐ6WDQGLQJௐ2IIHUVௐ
DQGௐ6XSSO\ௐ$UUDQJHPHQWVௐ
626$
ௐWKDWௐ\RXௐ
KROGௐ:KDWௐLVௐWKHௐDQQXDOௐVDOHVௐYROXPHௐIRUௐ
HDFKௐRIௐWKHVHௐFRQWUDFWVௐRYHUௐWKHௐSDVWௐWKUHHௐ
\HDUV"
&XUUHQWௐ*6$ௐ
*HQHUDOௐ6HUYLFHVௐ$GPLQLVWUDWLRQ
ௐFRQWUDFWௐLVௐ*6)'$


7DEOH
5HIHUHQFHV7HVWLPRQLDOV
/LQH,WHP6XSSO\UHIHUHQFHLQIRUPDWLRQIURPWKUHHFXVWRPHUVZKRDUHHOLJLEOHWREH6RXUFHZHOOSDUWLFLSDWLQJHQWLWLHV (QWLW\1DPH
&RQWDFW1DPH
3KRQH1XPEHU

.QR[YLOOHௐ)LUHௐ'HSDUWPHQW %REE\ௐ3DOPHU 
 

+RZHOOௐ)LUHௐ'LVWULFWௐ /RXLVௐ0HPPROR,,, 
 

&ODUNௐ&RXQW\ 5LFFDUGRௐ7HU]R  

7DPSDௐ,QWHUQDWLRQDOௐ$LUSRUW 2UHQௐ+DQVRQ 
Bid Number: RFP 113021 Vendor Name: Pierce Manufacturing 













 

EXHIBIT 1 591
7DEOH
7RS)LYH*RYHUQPHQWRU(GXFDWLRQ&XVWRPHUV
/LQH,WHP3URYLGHDOLVWRI\RXUWRSILYHJRYHUQPHQWHGXFDWLRQRUQRQSURILWFXVWRPHUV HQWLW\QDPHLVRSWLRQDO
LQFOXGLQJHQWLW\
W\SHWKHVWDWHRUSURYLQFHWKHHQWLW\LVORFDWHGLQVFRSHRIWKHSURMHFW V
VL]HRIWUDQVDFWLRQ
V
DQGGROODUYROXPHVIURPWKHSDVWWKUHH
\HDUV
(QWLW\1DPH (QWLW\7\SH
6WDWH
3URYLQFH
6FRSHRI:RUN
6L]HRI7UDQVDFWLRQV
'ROODU9ROXPH3DVW7KUHH<HDUV

86ௐ$UP\ *RYHUQPHQW 'LVWULFWRI
&ROXPELD'&
3XPSHUVௐUHVFXHVௐDHULDOV 1$ 1$ 

86ௐ$LUௐ)RUFH *RYHUQPHQW 'LVWULFWRI
&ROXPELD'&
3XPSHUVௐUHVFXHVௐDHULDOV 1$ 1$ 

%XUHDXௐRIௐ
/DQGௐ
0DQDJHPHQW
*RYHUQPHQW 'LVWULFWRI
&ROXPELD'&
:LOGODQGௐSXPSHUV 1$ 1$


86ௐ1DY\ *RYHUQPHQW 'LVWULFWRI
&ROXPELD'&
3XPSHUVௐUHVFXHVௐDHULDOV 1$ 1$ 

86ௐ0DULQHௐ
&RUSV
*RYHUQPHQW 'LVWULFWRI
&ROXPELD'&
3XPSHUVௐUHVFXHVௐDHULDOV 1$ 1$ 

7DEOH
$ELOLW\WR6HOODQG'HOLYHU6HUYLFH
'HVFULEH\RXUFRPSDQ\¶VFDSDELOLW\WRPHHWWKHQHHGVRI6RXUFHZHOOSDUWLFLSDWLQJHQWLWLHVDFURVVWKH86DQG&DQDGDDVDSSOLFDEOH <RXUUHVSRQVHVKRXOGDGGUHVVLQGHWDLODWOHDVWWKHIROORZLQJDUHDV ORFDWLRQVRI\RXUQHWZRUNRIVDOHVDQGVHUYLFHSURYLGHUVWKHQXPEHU RIZRUNHUV
IXOOWLPHHTXLYDOHQWV
LQYROYHGLQHDFKVHFWRUZKHWKHUWKHVHZRUNHUVDUH\RXUGLUHFWHPSOR\HHV RUHPSOR\HHVRIDWKLUG
SDUW\
DQGDQ\RYHUODSEHWZHHQWKHVDOHVDQGVHUYLFHIXQFWLRQV /LQH
,WHP 4XHVWLRQ 5HVSRQVH

 6DOHVௐIRUFH 3LHUFHௐ0DQXIDFWXULQJௐKDVௐDQௐLQVLGHௐVDOHVௐIRUFHௐWKDWௐPDQDJHVௐDௐJLYHQௐWHUULWRU\ௐ7KHௐ VXSSRUWௐFDQௐUDQJHௐIURPௐGHDOHUVௐFXVWRPHUௐUHTXHVWௐWUDGHௐVKRZVௐZDUUDQWLHVௐVSHFLILFVௐ VXSSRUWௐZLWKLQௐWKHௐELGVௐPDQDJLQJௐWKHௐVDOHௐDQGௐFRQILJXUDWLRQௐ7KHௐLQVLGHௐVDOHVௐIRONVௐ ZRUNௐZLWKௐLQWHUQDOௐ3LHUFHௐFRQWDFWVௐௐWRௐHQVXUHௐDௐVXFFHVVIXOௐEXLOGௐDQGௐGHOLYHU\ௐWRௐRXUௐ SUHIHUUHGௐGHDOHUௐQHWZRUN
7KHௐ2VKNRVKௐ$LUSRUWௐ3URGXFWVௐVDOHVௐIRUFHௐFRQVLVWVௐRIௐௐUHJLRQDOௐVDOHVௐPDQDJHUVௐZKRௐ DUHௐGLUHFWௐHPSOR\HHVௐRIௐ2VKNRVKௐ$LUSRUWௐ3URGXFWVௐௐ2XUௐVDOHVௐWHDPௐLVௐFRPPLWWHGௐWRௐ WKHௐIXOOௐFXVWRPHUௐOLIHF\FOHௐIURPௐLQLWLDOௐFRQWDFWௐWKURXJKRXWௐWKHௐYHKLFOHௐOLIHௐௐ,QௐDGGLWLRQௐ RXUௐLQWHUQDOௐVDOHVௐPDQDJHUVௐFRRUGLQDWHௐZLWKௐRXUௐ&DQDGLDQௐGHDOHUVKLSௐWRௐVXSSRUWௐWKHௐ FXVWRPHUௐUHODWLRQVKLS
5HIHUௐWRௐௐௐௐ'LUHFWRU\ௐௐ3LHUFHௐ'HDOHUVKLSௐ7HUULWRULHVௐ0DSSGIௐௐௐ 3LHUFHௐ$XWKRUL]HGௐ'HDOHUBB/LVWLQJSGIௐௐ$5))ௐ560ௐ0DSௐ1RYௐSGIௐ DQGௐௐ3LHUFHௐDQGௐ$LUSRUWௐ,QWHUQDOௐ&RQWDFWVௐ2UJௐ&KDUWSGIௐLQௐWKHௐ$GGLWLRQDOௐ 'RFXPHQWVௐIROGHUௐIRUௐPRUHௐLQIRUPDWLRQ


 'HDOHUௐQHWZRUNௐRUௐRWKHUௐGLVWULEXWLRQௐ
PHWKRGV
3LHUFHௐSURGXFWௐLVௐVROGௐYLDௐWKHௐDXWKRUL]HGௐ3LHUFHௐ'HDOHUௐQHWZRUNௐRIௐௐVDOHVௐ UHSUHVHQWDWLYHVௐWKDWௐDUHௐORFDWHGௐDFURVVௐWKHௐ86ௐDQGௐ&DQDGDௐDQGௐDUHௐEDFNHGௐE\ௐWKHௐ 3LHUFHௐIDFWRU\ௐVXSSRUWௐRIௐௐHPSOR\HHVௐWRௐDVVLVWௐZLWKௐSURGXFWௐTXDOLW\ௐDQGௐ VHUYLFHௐ,QௐDGGLWLRQௐWKHௐVDOHVௐIRUFHௐLVௐFRPSULVHGௐRIௐOHJDF\ௐWHQXUHௐDVௐZHOOௐDVௐQHZௐ JHQHUDWLRQVௐ0DQ\ௐRIௐRXUௐVDOHVௐUHSUHVHQWDWLYHVௐFDPHௐIURPௐRUௐDUHௐVWLOOௐSDUWௐRIௐWKHௐILUHௐ LQGXVWU\ௐLQௐVRPHௐZD\
7KHUHௐDUHௐ'HDOHUVௐORFDWHGௐDFURVVௐWKHௐ86ௐDQGௐ&DQDGDௐWKDWௐKDYHௐEHHQௐDVVLJQHGௐ WHUULWRU\ௐWRௐSURYLGHௐ6DOHVௐ6HUYLFHௐDQGௐDIWHUPDUNHWௐVXSSRUWௐௐௐGD\VௐRIௐWKHௐ\HDU 7KHௐGHDOHUௐQHWZRUNௐKDVௐLQYHVWHGௐLQௐRQௐKDQGௐLQYHQWRU\ௐDVௐZHOOௐDVௐWKHௐIDFWRU\ௐDQGௐ GHGLFDWHGௐDIWHUPDUNHWௐLQYHQWRU\ௐDYDLODEOHௐRQOLQHௐIRUௐWKHPௐWRௐXWLOL]HௐDQGௐGURSௐVKLSௐWRௐ WKHௐHQGௐFXVWRPHU¶VௐORFDWLRQ
$VௐSUHYLRXVO\ௐPHQWLRQHGௐZHௐDOVRௐSDUWQHUௐZLWKௐ0$;,0(7$/ௐWRௐVXSSRUWௐRXUௐ&DQDGLDQௐ FXVWRPHUVௐE\ௐEHLQJௐDௐGLVWULEXWRUௐIRUௐ0$;,0(7$/ௐSURGXFWVௐ 2VKNRVKௐ$LUSRUWௐ3URGXFWVௐVHOOVௐGLUHFWௐGRPHVWLFDOO\ௐDQGௐSDUWQHUVௐZLWKௐGHDOHUௐ RUJDQL]DWLRQVௐLQWHUQDWLRQDOO\ௐLQFOXGLQJௐ&DQDGDௐௐ
5HIHUௐWRௐௐௐௐ'LUHFWRU\ௐௐ3LHUFHௐ'HDOHUVKLSௐ7HUULWRULHVௐ0DSSGIௐDQGௐௐௐ 3LHUFHௐ$XWKRUL]HGௐ'HDOHUBB/LVWLQJSGIௐLQௐWKHௐ$GGLWLRQDOௐ'RFXPHQWVௐIROGHUௐIRUௐ PRUHௐLQIRUPDWLRQ


Bid Number: RFP 113021 Vendor Name: Pierce Manufacturing 













 

EXHIBIT 1 592
 6HUYLFHௐIRUFH 3LHUFHௐDQGௐLWVௐGHDOHUௐQHWZRUNௐRIIHUௐDௐZLGHௐYDULHW\ௐRIௐ$IWHUPDUNHWௐVHUYLFHVௐWRௐKHOSௐ FXVWRPHUVௐPDLQWDLQௐWKHLUௐ3LHUFHௐEUDQGHGௐILUHௐDSSDUDWXVௐௐVHUYLFHௐFHQWHUVௐ WKURXJKRXWௐ1RUWKௐ$PHULFDௐDUHௐGHGLFDWHGௐWRௐVHUYLFLQJௐ3LHUFHௐDSSDUDWXVௐWKUXௐLWVௐLQGXVWU\ OHDGLQJௐLQGHSHQGHQWO\ௐRZQHGௐ ௐPDQDJHGௐGHDOHUௐQHWZRUNௐௐ8QLWHGௐ6WDWHVௐ ௐௐ &DQDGLDQௐGHDOHUVKLSVௐVXSSRUWௐRXUௐZLGHௐDUUD\ௐRIௐVHUYLFHௐFHQWHUVௐ3LHUFHௐDXWKRUL]HGௐ VHUYLFHௐFHQWHUVௐRIIHU

‡ௐ'HGLFDWHGௐ6HUYLFHௐ3URIHVVLRQDOV
‡ௐ1HDUO\ௐௐPRELOHௐVHUYLFHௐYHKLFOHVௐVWUDWHJLFDOO\ௐORFDWHGௐWKURXJKRXWௐ1RUWKௐ$PHULFD ‡ௐ2IIHUௐVFKHGXOHGௐ ௐXQVFKHGXOHGௐPDLQWHQDQFHௐVHUYLFHV
‡ௐௐDFFHVVௐWRௐ3LHUFHௐ7HFKQLFDOௐ6XSSRUWௐ+RW/LQHௐ
‡ௐ$ELOLW\ௐWRௐH[HFXWHௐZDUUDQW\UHODWHGௐUHSDLUVௐLQௐDFFRUGDQFHௐZLWKௐWKHௐ3LHUFHௐOLPLWHGௐ ZDUUDQW\ௐVWDWHPHQW
3LHUFHௐDOVRௐRIIHUVௐDௐIXOOௐOLQHௐRIௐVSDUHௐSDUWVௐDYDLODEOHௐIRUௐSXUFKDVHௐWKUXௐLWVௐGHGLFDWHGௐ GHDOHUௐQHWZRUNௐ7KHௐVSDUHௐSDUWVௐZDUHKRXVHௐORFDWHGௐLQௐ$SSOHWRQௐ:LVFRQVLQௐERDVWVௐ RYHUௐௐVTௐIWௐRIௐVWRUDJHௐVSDFHௐDOOௐRIௐZKLFKௐVXSSRUWVௐ3LHUFHௐILUHௐDSSDUDWXVௐ .H\ௐIDFWVௐDERXWௐWKHௐZDUHKRXVHௐLQFOXGH

‡ௐ'HGLFDWHGௐDQGௐFRPPLWWHGௐRQKDQGௐVSDUHௐSDUWVௐLQYHQWRU\ ‡ௐ0DQDJHPHQWௐRIௐRYHUௐௐXQLTXHௐVSDUHௐSDUWௐQXPEHUVௐ LQYHQWRU\ௐPLQPD[ௐ
SULFLQJௐFRXQWU\ௐRIௐRULJLQௐHWF

‡ௐ6DPHGD\ௐ ௐQH[WGD\ௐVKLSSLQJௐVHUYLFHVௐIURPௐ836ௐ)HG([ௐDQGௐ;32 ‡ௐௐZHEVLWHௐWRௐORFDWHௐDQGௐFKHFNௐSULFLQJௐ ௐDYDLODELOLW\ௐRIௐVSDUHௐSDUWVௐE\ௐDXWKRUL]HGௐ GHDOHU
‡ௐ7HQVௐRIௐWKRXVDQGVௐRIௐGLJLWDOௐSKRWRJUDSKVௐ ௐ'ௐDUWZRUNௐRIௐUHSODFHPHQWௐSDUWVௐIRUௐ IDVWௐ ௐHDV\ௐLGHQWLILFDWLRQ
3LHUFHௐRIIHUVௐDௐFRPSOHWHௐVHWௐRIௐWUDLQLQJௐFODVVHVௐIRUௐERWKௐRSHUDWRUVௐ ௐPDLQWDLQHUVௐWRௐ NHHSௐ\RXUௐ3LHUFHௐDSSDUDWXVௐUXQQLQJௐDWௐSHDNௐSHUIRUPDQFH ‡ௐ5HJLRQDOௐ ௐ&RUSRUDWHௐWUDLQLQJௐHYHQWVௐKHOGௐWKURXJKRXWௐWKHௐFDOHQGDUௐ\HDU ‡ௐ,QVWUXFWRUVௐZLWKௐRYHUௐௐFRPELQHGௐ\HDUVௐRIௐ3LHUFHௐ ௐLQGXVWU\ௐH[SHUWLVH ‡ௐ,QQRYDWLYHௐ7UDLQLQJௐ7UXFN
ௐNH\ௐWHFKQRORJ\ௐPRXQWHGௐRQௐVWDQGDORQHௐWUXFNௐWRௐVLPXODWHௐ DQ\ௐNH\ௐV\VWHP
‡ௐ7HFKQRORJ\ௐWUDLQLQJௐRQௐNH\ௐFRPSRQHQWVௐVXFKௐDVௐ3LHUFHௐ8OWLPDWHௐ&RQILJXUDWLRQௐ

38&Œ
ௐZDWHUௐSXPSVௐ7$.ŠௐLQGHSHQGHQWௐVXVSHQVLRQௐV\VWHPVௐ+XVN\Œௐ)RDPௐ V\VWHPVௐDQGௐ&RPPDQGௐ=RQHŒௐ,,,
‡ௐ2SHUDWLRQௐRYHUYLHZௐRIௐIRDPௐ ௐDHULDOௐGHYLFHV
$WWDFKHGௐ\RXௐZLOOௐILQGௐDௐVXPPDU\ௐSHUௐDXWKRUL]HGௐGHDOHUௐPRELOHௐYHKLFOHVௐDQGௐ DFNQRZOHGJPHQWௐRIௐVHUYLFHௐWHFKQLFLDQVௐDORQJௐZLWKௐGHDOHUௐFRQWDFWௐDQGௐWKHௐWHUULWRU\ௐWKH\ௐ FRYHU
2VKNRVKௐ$LUSRUWௐ3URGXFWVௐHPSOR\VௐIXOOௐWLPHௐ)LHOGௐ6HUYLFHௐ5HSUHVHQWDWLYHVௐWRௐSURYLGHௐ YHKLFOHௐLQVHUYLFHௐWUDLQLQJௐDQGௐVHUYLFHௐZRUNௐௐ:HௐDOVRௐUHO\ௐRQௐVXSSRUWௐIURPௐ RUJDQL]DWLRQVௐDFURVVௐWKHௐ86ௐDQGௐKDYHௐVHUYLFHௐSURYLGHUௐDJUHHPHQWVௐWRௐSURYLGHௐORFDOௐ VXSSRUWௐWRௐRXUௐFXVWRPHUVௐDVௐZHOOௐௐ,QௐDGGLWLRQௐZHௐDUHௐVXSSRUWHGௐWKURXJKௐ2VKNRVKௐ &RUSRUDWLRQ¶VௐWUDLQLQJௐFHQWHUௐWRௐSURYLGHௐZRUOGFODVVௐPDLQWHQDQFHௐDQGௐRSHUDWLRQVௐ WUDLQLQJௐௐ7KHVHௐWUDLQLQJVௐDUHௐGHVLJQHGௐVSHFLILFDOO\ௐIRUௐRXUௐ$5))ௐSURGXFWVௐDQGௐDUHௐ DYDLODEOHௐWRௐRXUௐGHDOHUVௐDQGௐFXVWRPHUVௐDOLNHௐௐ
5HIHUௐWRௐௐௐௐ'LUHFWRU\ௐௐ3LHUFHௐ'HDOHUVKLSௐ7HUULWRULHVௐ0DSSGIௐௐ3LHUFHௐ 'HDOHUௐ6HUYLFHௐ ௐ6DOHVௐ&RYHUDJHSGIௐDQGௐௐ$5))ௐ6HUYLFHௐ3URYLGHUVௐ0DSSGIௐ LQௐWKHௐ$GGLWLRQDOௐ'RFXPHQWVௐIROGHUௐIRUௐPRUHௐLQIRUPDWLRQ 

 'HVFULEHௐWKHௐRUGHULQJௐSURFHVVௐ,IௐRUGHUVௐ
ZLOOௐEHௐKDQGOHGௐE\ௐGLVWULEXWRUVௐGHDOHUVௐRUௐ
RWKHUVௐH[SODLQௐWKHௐUHVSHFWLYHௐUROHVௐRIௐWKHௐ
3URSRVHUௐDQGௐRWKHUV
:KHQௐWKHௐFXVWRPHUௐZRUNVௐZLWKௐWKHௐ3LHUFHௐDXWKRUL]HGௐGHDOHUௐWKH\ௐZLOOௐDFFHSWௐDOOௐ SXUFKDVHௐRUGHUV
ௐKRZHYHUௐHYHU\ௐVDOHௐLVௐFRQILJXUHGௐLQௐWKHௐ3LHUFHௐFXVWRPL]HGௐWUXFNௐ FRQILJXUDWRUௐ3XOVHௐ7KLVௐVDOHVௐWRROௐLQFOXGHVௐWKHௐFRUUHVSRQGLQJௐFRRSHUDWLYHௐ SURFXUHPHQWௐRSWLRQௐDSSOLFDEOHௐWRௐWKHௐVDOHௐ7KLVௐRSWLRQௐLVௐXVHGௐWRௐJHQHUDWHௐPRQWKO\ௐ DXGLWVௐWKDWௐ3LHUFHௐSHUIRUPVௐZLWKௐWKHLUௐGHDOHUௐQHWZRUNௐDVௐZHOOௐDVௐJHQHUDWHௐWKHௐ TXDUWHUO\ௐUHTXLUHGௐUHSRUWVௐVHQWௐGLUHFWௐWRௐWKHௐFRQWUDFWLQJௐDJHQF\ௐௐ7KHௐDXWKRUL]HGௐ 'HDOHUௐQHWZRUNௐXWLOL]HVௐWKHௐFXVWRPL]HGௐDSSDUDWXVௐVSHFLILFDWLRQௐVRIWZDUHௐ 38/6(
ௐWRௐ
FRQILJXUHௐWRௐWKHௐFXVWRPHU¶VௐH[SHFWDWLRQVௐDQGௐLVௐXVHGௐLQWHUQDOO\ௐWKURXJKRXWௐWKHௐVXSSO\ௐ FKDLQௐRIௐWKHௐRUGHUௐIURPௐERRNLQJௐWKHௐRUGHUௐWRௐHQJLQHHUௐWKHௐILQDOௐSURGXFWௐ7KHௐWRROௐLVௐ VXSSRUWHGௐZLWKௐLQWHUQDOௐFRPPXQLFDWLRQௐWRROVௐVXFKௐDVௐZRUNIORZௐ&RPPXQLFDWLRQௐ&HQWUDOௐ RQOLQHௐVFKHGXOLQJௐ%XLOGௐ6WDWXVௐDQGௐDௐFRPSOHWHௐ7UXFNௐ/LEUDU\ௐ7KLVௐSURYLGHVௐRXUௐ 'HDOHUௐQHWZRUNௐDௐGLUHFWௐOLQNௐWRௐWKHௐIDFWRU\ௐWRௐDFFXUDWHO\ௐFRPPXQLFDWHௐGHWDLOVௐWRௐWKHௐ HQGௐXVHUௐௐ
$LUSRUWௐ3URGXFWVௐZLOOௐEHௐWKHௐSULPDU\ௐSRLQWௐRIௐFRQWDFWௐIRUௐVDOHVௐLQTXLULHVௐH[FHSWௐZKHUHௐ ZHௐKDYHௐDQௐDXWKRUL]HGௐGHDOHUௐௐ:LWKௐFRPSOH[LW\ௐRIௐ$5))ௐYHKLFOHVௐRXUௐWHDPௐZLOOௐZRUNௐ GLUHFWO\ௐZLWKௐWKHௐFXVWRPHUௐWRௐFXVWRPL]HௐWKHLUௐWUXFNௐFRQILJXUDWLRQௐXVLQJௐWKHௐEDVHௐYHKLFOHௐ DVௐDௐVWDUWLQJௐSRLQWௐ2SWLRQVௐZLOOௐEHௐDGGHGௐWRௐWKHௐEDVHௐSULFHௐZLWKௐWKHௐ6RXUFHZHOOௐ GLVFRXQWௐௐ7KLVௐTXRWDWLRQௐZLOOௐEHௐXVHGௐE\ௐWKHௐFXVWRPHUௐWRௐLVVXHௐDௐSXUFKDVHௐRUGHUௐRUௐ FRQWUDFWௐZKLFKௐZLOOௐEHௐUHYLHZHGௐE\ௐ$LUSRUWௐ3URGXFWVௐDQGௐDFFHSWHGௐ$LUSRUWௐ3URGXFWVௐ ZLOOௐWKHQௐEHௐUHVSRQVLEOHௐIRUௐPDQXIDFWXUHௐRIௐWKHௐYHKLFOH 


'HVFULEHௐLQௐGHWDLOௐWKHௐSURFHVVௐDQGௐ
SURFHGXUHௐRIௐ\RXUௐFXVWRPHUௐVHUYLFHௐ
SURJUDPௐLIௐDSSOLFDEOHௐௐ,QFOXGHௐ\RXUௐ
UHVSRQVHWLPHௐFDSDELOLWLHVௐDQGௐ
FRPPLWPHQWV DV ZHOO DV DQ\ௐLQFHQWLYHV
$)7(50$5.(7ௐ3,(5&(ௐ02'(/
3LHUFHௐVHUYLFHௐDIWHUௐWKHௐVDOHௐLVௐZKHUHௐZHௐWUXO\ௐDUHௐVHWௐDSDUWௐIURPௐRWKHUVௐ7KHௐ3LHUFHௐ 'HDOHUௐQHWZRUNௐVSDQVௐDFURVVௐWKHௐ86ௐDQGௐ&DQDGDௐDQGௐHDFKௐKDYHௐPDGHௐLQYHVWPHQWௐ LQௐIDFLOLWLHVௐLQYHQWRU\ௐVWDIIௐDQGௐWUDLQLQJௐ7KHௐ'HDOHUௐLVௐWKHௐILUVWௐSRLQWௐRIௐFRQWDFWௐIRUௐ WKH FXVWRPHU KRZHYHU DOO FXVWRPHUV FDQ DFFHVV 3LHUFHSDUWVFRP WR DLG LQ DQ\ௐ Bid Number: RFP 113021 Vendor Name: Pierce Manufacturing 













 

EXHIBIT 1 593
WKDW KHOS \RXU SURYLGHUV PHHW \RXU VWDWHG
VHUYLFHௐJRDOVௐRUௐSURPLVHV
VHUYLFH QHHGV WKH\ PD\ KDYH
7($0ௐ0(0%(56
3LHUFHௐ6HUYLFHௐ%ULJDGH
$QௐDUP\ௐRIௐௐVHUYLFHௐWHFKQLFLDQVௐDFURVVௐWKHௐ86ௐDQGௐ&DQDGDௐ &HUWLILHGௐ0DVWHUௐ7HFKQLFLDQV
:HௐVSHFLILFDOO\ௐFUHDWHGௐWKHௐ3LHUFHௐ&HUWLILHGௐ0DVWHUௐ7HFKQLFLDQௐSURJUDPௐWRௐHQVXUHௐWKDWௐ RXUௐ6HUYLFHௐ%ULJDGHௐSURIHVVLRQDOVௐSRVVHVVௐWKHௐKLJKHVWௐOHYHOௐRIௐSURILFLHQF\ௐZLWKௐ WRGD\¶VௐVRSKLVWLFDWHGௐHPHUJHQF\ௐYHKLFOHVௐLQFOXGLQJௐQRQ3LHUFHௐDSSDUDWXV 7KHௐ5LJKWௐ$WWLWXGHௐDQGௐWKHௐ5LJKWௐ7RROV
2XUௐWHDPௐPHPEHUVௐWDNHௐSULGHௐLQௐJRLQJௐKRPHௐDWௐWKHௐHQGௐRIௐHDFKௐGD\ௐNQRZLQJௐWKH\ௐ PDGHௐDௐGLIIHUHQFHௐ7KHௐPRELOHௐWUDLQLQJௐXQLWௐWDNHVௐ&XVWRPHUௐ6HUYLFHௐWUDLQLQJௐWRௐ DQRWKHUௐOHYHOௐDQGௐEULQJVௐWUDLQLQJௐWRௐWKHௐFXVWRPHUௐ7KLVௐPRELOHௐXQLWௐKDVௐEXLOWLQௐWUDLQLQJௐ WRROVௐDQGௐSURSVௐWKDWௐDUHௐFRQILJXUDEOHௐWRௐWKHௐWUDLQLQJௐQHHGVௐRIௐRXUௐFXVWRPHUVௐ,WௐDOORZVௐ WKHௐWHFKQLFLDQௐWRௐWURXEOHVKRRWௐGLVPDQWOHௐDQGௐPRVWௐLPSRUWDQWO\ௐSURYLGHௐWKHௐKDQGVRQௐ WUDLQLQJௐFXVWRPHUVௐDVNௐIRU
,19(1725<
$VௐWKHௐPDQXIDFWXUHUௐIDFLOLWLHVௐDUHௐDYDLODEOHௐLQௐ$SSOHWRQௐ:,ௐ:H\DXZHJDௐ:,ௐDQGௐ %UDGHQWRQௐ)/ௐ7KHVHௐIDFLOLWLHVௐDUHௐHTXLSSHGௐZLWKௐIDFWRU\ௐSHUVRQQHOௐDQGௐFRPPLWWHGௐ KHDOWK\ௐVWRFNௐRIௐLQYHQWRU\ௐGHGLFDWHGௐWRௐVHUYLFHௐDQGௐUHSODFHPHQWௐSDUWVௐWRௐHQVXUHௐTXLFNௐ UHVSRQVHௐDQGௐPLQLPL]HௐGRZQௐWLPH
)XUWKHUPRUHௐ3LHUFHௐ0DQXIDFWXULQJௐ,QFௐKRXVHVௐLQYHQWRU\ௐLQௐDௐGHGLFDWHGௐIDFLOLW\ௐZLWKௐDௐ GHGLFDWHGௐVKLSSLQJௐDUHDௐWKDWௐHQVXUHVௐVHUYLFHௐSDUWVௐDUHௐJLYHQௐSULRULW\ௐDQGௐH[WHQGVௐDௐ FXVWRPL]HGௐ3LHUFHௐDIWHUPDUNHWௐZHEVLWHௐIRUௐDXWKRUL]HGௐ'HDOHUVௐWRௐFRQGXFWௐEXVLQHVVௐLQௐ UHDOWLPH
)$&725<ௐ+2856ௐ2)ௐ23(5$7,21ௐ
3LHUFHௐ0DQXIDFWXULQJௐ,QFௐDQGௐ2VKNRVKௐ$LUSRUWௐSURGXFWVௐDOVRௐPDLQWDLQVௐDௐௐKRXUௐௐ GD\ௐDௐZHHNௐWROOௐIUHHௐHPHUJHQF\ௐKRWௐOLQHௐDQGௐHPSOR\VௐDௐVWDIIௐRIௐGHGLFDWHGௐLQGLYLGXDOVௐ WRௐWURXEOHVKRRWLQJௐDQGௐSDUWVௐVXSSRUWௐ3LHUFHௐ&XVWRPHUௐ6HUYLFHௐFRUHௐKRXUVௐRIௐ RSHUDWLRQௐDUHௐ0RQGD\ௐ±ௐ)ULGD\ௐ
ௐDPௐ±ௐ
ௐSPௐ&67ௐ:HௐDOVRௐKDYHௐ3LHUFHௐ
IDFWRU\ௐWHFKQLFLDQVௐRQௐFDOOௐIRUௐDIWHUKRXUVௐVXSSRUWௐDYDLODEOHௐௐKRXUVௐDௐGD\ௐVHYHQௐ GD\VௐDௐZHHN
352%/(0ௐ,'(17,),&$7,21ௐ ௐ5(62/87,21ௐ
$VௐSURGXFWௐRUௐVHUYLFHௐLVVXHVௐDUHௐLGHQWLILHGௐE\ௐWKHௐFXVWRPHUௐWKH\ௐDUHௐWRௐFRQWDFWௐWKHLUௐ ORFDOௐ3LHUFHௐDXWKRUL]HGௐGHDOHUௐVLQFHௐWKH\ௐDUHௐWKHௐFXVWRPHU¶VௐILUVWௐSRLQWௐRIௐFRQWDFWௐ$OOௐ LVVXHVௐDUHௐGRFXPHQWHGௐUHVROYHGௐDQGௐDUFKLYHGௐIRUௐIXWXUHௐUHIHUHQFHௐE\ௐWKHௐORFDOௐ GHDOHUVKLSௐ,IௐWKHUHௐLVௐDQௐLVVXHௐWKDWௐQHHGVௐHOHYDWHGௐDVVLVWDQFHௐWKHௐGHDOHUVKLSௐZLOOௐ FRQWDFWௐWKHௐ3LHUFHௐFXVWRPHUௐVHUYLFHௐDFFRXQWௐUHSUHVHQWDWLYHௐIRUௐDVVLVWDQFHௐ 3DUWVௐLGHQWLILFDWLRQௐLVௐSURYLGHGௐWRௐERWKௐWKHௐGHDOHUௐDQGௐWKHௐ)LUHௐ'HSDUWPHQWௐWKURXJKௐ DQௐRQOLQHௐZHEEDVHGௐDSSOLFDWLRQௐIRUௐWKHௐVSHFLILFௐWUXFNௐ$FFHVVௐZLOOௐEHௐJUDQWHGௐXVLQJௐ WKHௐVSHFLILFௐ9,1ௐQXPEHUௐRIௐWKHௐYHKLFOHௐDQGௐWKHௐRQOLQHௐZHEௐDSSOLFDWLRQௐSURYLGHVௐWKHௐ DELOLW\ௐWRௐYLHZௐFRPSOHWHௐELOOVௐRIௐPDWHULDOVௐGLJLWDOௐSKRWRJUDSKVௐSDUWVௐGUDZLQJVௐ DVVHPEO\ௐGUDZLQJVௐDQGௐDFFHVVௐWRௐDOOௐFXUUHQWௐRSHUDWLRQௐPDLQWHQDQFHௐDQGௐVHUYLFHௐ SXEOLFDWLRQVௐ7KHௐHQGௐXVHUௐFDQௐDFFHVVௐWKLVௐLQIRUPDWLRQௐYLDௐWKHௐ*XHVWௐ/RJLQ 7(&+1,&$/ௐ6(59,&(ௐ6833257
%RWKௐ3LHUFHௐDQGௐWKHLUௐDXWKRUL]HGௐ'HDOHUVௐFDQௐSURYLGHௐERWKௐLQKRXVHௐDQGௐRQVLWHௐ VHUYLFHௐIRUௐWKHௐDSSDUDWXVௐDORQJௐZLWKௐWUDLQLQJௐSHUௐUHTXHVWௐ5HSODFHPHQWௐSDUWVௐDQGௐ YDULRXVௐOHYHOVௐRIௐVHUYLFHௐDIWHUௐGHOLYHU\ௐDUHௐDYDLODEOHௐIURPௐ\RXUௐORFDOௐ3LHUFHௐDXWKRUL]HGௐ GHDOHUௐLQFOXGLQJௐEXWௐQRWௐOLPLWHGௐWRௐWKRVHௐVKRZQௐEHORZ

6(59,&(

:DUUDQW\ௐUHSDLUௐIRUௐ3LHUFHௐSURGXFWௐOLQHௐIRUௐDOOௐLWHPVௐH[FHSWௐIRUௐWKRVHௐWKDWௐPXVWௐEHௐ KDQGOHGௐGLUHFWO\ௐE\ௐDQௐDXWKRUL]HGௐFRPSRQHQWௐPDQXIDFWXUHௐVXFKௐDVௐHQJLQHௐDQGௐ WUDQVPLVVLRQ
'LUHFWௐDFFHVVௐWRௐ3LHUFHௐWHFKQLFDOௐVXSSRUW
5RXWLQHௐSUHYHQWDWLYHௐPDLQWHQDQFH
$QQXDOௐDHULDOௐODGGHUௐWHVWLQJ
3XPSௐWHVWLQJ
*URXQGௐODGGHUௐWHVWLQJ
1)3$ௐ
ௐDQQXDOௐLQVSHFWLRQVௐPDLQWHQDQFHௐDQGௐWHVWLQJ
5HSDLUVௐIURPௐVPDOOௐPLQRUௐLVVXHVௐWRௐPDMRUௐRYHUKDXOVௐDQGௐPDQ\ௐRWKHUௐVHUYLFHV 'HDOHUௐUHSDLUௐVHUYLFHVௐH[WHQGௐWRௐPRVWௐRWKHUௐILUHௐDQGௐHPHUJHQF\ௐUHVFXHௐSURGXFWௐOLQHVௐ LQௐDGGLWLRQௐWRௐ3LHUFHௐ0DQXIDFWXULQJ
6HUYLFHௐSURYLGHGௐE\ௐ(97ௐ$6(ௐ3LHUFHௐDQGௐLQGXVWU\ௐVSHFLILFௐFHUWLILHGௐWHFKQLFLDQV $OOௐ3LHUFHௐDXWKRUL]HGௐVDOHVௐDQGௐVHUYLFHௐGHDOHUVௐKDYHௐDFFHVVௐWRௐ3LHUFH¶VௐH[WHQVLYHௐ OHYHOௐRIௐWHFKQLFDOௐDQGௐFXVWRPHUௐVHUYLFHௐVXSSRUWௐVWDII
3$576

3LHUFH DXWKRUL]HG GHDOHUV PDLQWDLQ D ODUJH DVVRUWPHQW RIௐSURGXFWV VXSSOLHG ZLWK ILUH 

Bid Number: RFP 113021 Vendor Name: Pierce Manufacturing 













 

EXHIBIT 1 594
DSSDUDWXV
,QFOXGLQJௐEXWௐQRWௐOLPLWHGௐWRௐWKHௐPRVWௐFRPPRQO\ௐUHTXLUHGௐSDUWVௐDQGௐFRPSRQHQWVௐ UHTXLUHGௐIRUௐDSSDUDWXVௐUHSDLUௐௐ7KLVௐOHYHOௐRIௐLQYHQWRU\ௐHQDEOHVௐ³RXWௐRIௐVHUYLFH´ௐWLPHௐWRௐ EHௐNHSWௐWRௐDௐEDUHௐPLQLPXP
$OOௐ3LHUFHௐDXWKRUL]HGௐVDOHVௐDQGௐVHUYLFHௐGHDOHUVௐKDYHௐDFFHVVௐWRௐ3LHUFH¶VௐH[WHQVLYHௐ OHYHOௐRIௐUHSODFHPHQWௐSDUWVௐLQYHQWRU\ௐZKLFKௐLVௐPRUHௐWKDQௐ0ௐDVௐZHOOௐDVௐDQ\ௐ3LHUFHௐ UHTXLUHGௐIDEULFDWLRQௐVHUYLFHV
2VKNRVKௐ$LUSRUWௐ3URGXFWVௐSDUWQHUVௐZLWKௐ3LHUFHௐ0DQXIDFWXULQJ VௐLQWHUQDOௐFXVWRPHUௐ
VXSSRUWௐWHDPௐWRௐSURYLGHௐWKHௐVDPHௐVXSHULRUௐVHUYLFHௐIRUௐPXQLFLSDOௐSURGXFWVௐZLWKௐWKHௐ VPDOOHUௐVFDOHௐRIௐ$5))ௐSURGXFWVௐ:HௐPDLQWDLQௐDௐௐKRXUௐௐGD\ௐDௐZHHNௐWROOௐIUHHௐ HPHUJHQF\ௐKRWௐOLQHௐZLWKௐFRUHௐKRXUVௐRIௐRSHUDWLRQௐEHLQJௐ0RQGD\ௐWKURXJKௐ)ULGD\ௐ ௐ
DPௐ±ௐ
ௐSPௐ&67ௐ:HௐDOVRௐKDYHௐ3LHUFHௐIDFWRU\ௐWHFKQLFLDQVௐRQௐFDOOௐIRUௐDIWHUKRXUVௐ VXSSRUWௐDYDLODEOHௐௐKRXUVௐDௐGD\ௐVHYHQௐGD\VௐDௐZHHNௐYLDௐRXUௐVHUYLFHௐVXSSRUWௐOLQHௐ 
 'HVFULEHௐ\RXUௐDELOLW\ௐDQGௐZLOOLQJQHVVௐWRௐ
SURYLGHௐ\RXUௐSURGXFWVௐDQGௐVHUYLFHVௐWRௐ
6RXUFHZHOOௐSDUWLFLSDWLQJௐHQWLWLHVௐLQௐWKHௐ
8QLWHGௐ6WDWHV
3LHUFHௐ0DQXIDFWXULQJௐ,QFௐKDVௐௐ86ௐEDVHGௐDXWKRUL]HGௐGHDOHUVௐHDFKௐZKLFKௐKDVௐDQௐ HVWDEOLVKHVௐVDOHVௐDQGௐVHUYLFHௐLQIUDVWUXFWXUHௐWRௐVXSSRUWௐWKHௐVDOHௐRIௐRXUௐZKROHௐJRRGVௐ IURPௐWLPHௐRIௐVDOHௐWKURXJKௐLWVௐOLIHF\FOHௐ
:HௐDUHௐFRPPLWWHGௐWRௐVXSSRUWௐWKHௐFXVWRPHUௐE\ௐHGXFDWLQJௐWKHPௐLQௐDOOௐSRVVLEOHௐDYHQXHௐ WRௐHQVXUHௐWKH\ௐNQRZௐWKHௐEHQHILWVௐRIௐ6RXUFHZHOOௐ
3LHUFHௐZLOOௐEHௐDEOHௐWRௐVXSSRUWௐWKHௐHQWLUHௐ86ௐLQFOXGLQJௐ+DZDLLௐDQGௐ$ODVNDௐDORQJௐZLWKௐ &DQDGDௐUHJLRQVௐ2XUௐHVWDEOLVKHGௐGHDOHUௐQHWZRUNௐLQFOXGHVௐDVVLJQPHQWௐIRUௐWKHVHௐ WHUULWRULHV
$LUSRUWௐ3URGXFWVௐLVௐDEOHௐDQGௐZLOOLQJௐWRௐSURYLGHௐRXUௐSURGXFWVௐDQGௐVHUYLFHVௐWRௐ SDUWLFLSDWLQJௐHQWLWLHVௐLQௐWKHௐ8QLWHGௐ6WDWHV


 'HVFULEHௐ\RXUௐDELOLW\ௐDQGௐZLOOLQJQHVVௐWRௐ
SURYLGHௐ\RXUௐSURGXFWVௐDQGௐVHUYLFHVௐWRௐ
6RXUFHZHOOௐSDUWLFLSDWLQJௐHQWLWLHVௐLQௐ&DQDGD
3LHUFHௐ0DQXIDFWXULQJௐ,QFௐKDVௐௐ86ௐEDVHGௐDXWKRUL]HGௐGHDOHUVௐHDFKௐZKLFKௐKDVௐDQௐ HVWDEOLVKHVௐVDOHVௐDQGௐVHUYLFHௐLQIUDVWUXFWXUHௐWRௐVXSSRUWௐWKHௐVDOHௐRIௐRXUௐZKROHௐJRRGVௐ IURPௐWLPHௐRIௐVDOHௐWKURXJKௐLWVௐOLIHF\FOHௐௐ3LHUFHௐ0DQXIDFWXULQJௐ,QFௐKDVௐWKUHHௐ'HDOHUVௐ WKDWௐFRYHUௐWKHௐ&DQDGLDQௐWHUULWRULHVௐ±ௐ&RPPHUFLDOௐ(PHUJHQF\ௐ(TXLSPHQWௐ6DIHW\ௐ 6RXUFHௐDQGௐ/ௐ¶$UVHQDO
&RPPHUFLDOௐ(PHUJHQF\ௐ(TXLSPHQWௐLVௐWKHௐODUJHVWௐRIௐWKRVHௐH[FOXVLYHௐGHDOHUVௐ7KH\ௐ FRYHUௐ:HVWHUQௐ&DQDGDௐ
%&ௐ$%ௐ6.ௐ0%
ௐ2QWDULRௐDVௐZHOOௐDVௐWKHௐ1RUWKHUQௐ
7HUULWRULHVௐ
<7ௐ1:7ௐ17

3LHUFHௐEUDQGVௐWKHௐ0$;,ௐ6DEHUௐFXVWRPFKDVVLVௐILUHௐDSSDUDWXVௐZKLFKௐDUHௐDOVRௐ PDUNHWHGௐLQௐ&DQDGDௐ3LHUFHௐLVௐRXUௐDXWKRUL]HGௐGHDOHUVௐDUHௐLQௐH[FOXVLYHௐSURGXFWௐ SDUWQHUVKLSௐVLQFHௐௐZLWKௐ0$;,0(7$/ௐ3LHUFHௐLVௐFRPPLWWHGௐWRௐJURZLQJௐWKHௐPDUNHWௐ LQௐ&DQDGDௐZKLOHௐDOVRௐSURYLGLQJௐVHUYLFHௐVXSSRUWௐ
$LUSRUWௐ3URGXFWVௐZLOOௐZRUNௐLQௐFRQMXQFWLRQௐZLWKௐRXUௐDXWKRUL]HGௐGHDOHU V
ௐDQGௐWRJHWKHUௐ
ZHௐDUHௐDEOHௐDQGௐZLOOLQJௐWRௐSURYLGHௐRXUௐSURGXFWVௐDQGௐVHUYLFHVௐWRௐSDUWLFLSDWLQJௐHQWLWLHVௐ LQௐ&DQDGD


 ,GHQWLI\ௐDQ\ௐJHRJUDSKLFௐDUHDVௐRIௐWKHௐ8QLWHGௐ
6WDWHVௐRUௐ&DQDGDௐWKDWௐ\RXௐZLOOௐ127ௐEHௐ
IXOO\ௐVHUYLQJௐWKURXJKௐWKHௐSURSRVHGௐFRQWUDFW
7KHUHௐDUHௐQRௐJHRJUDSKLFௐDUHDVௐLQௐWKHௐ86ௐRUௐ&DQDGDௐWKDWௐZHௐZLOOௐQRWௐEHௐIXOO\ௐ VHUYLFLQJௐWKURXJKௐWKHௐSURSRVHGௐFRQWUDFWௐ
3LHUFHௐDQGௐ$LUSRUWௐ3URGXFWVௐDUHௐSURXGௐWRௐSURYLGHௐH[FHOOHQWௐFRYHUDJHௐDFURVVௐWKHௐ QDWLRQௐ7KHUHௐDUHௐQRௐDUHDVௐWKURXJKRXWௐ86ௐRUௐ&DQDGDௐWKDWௐZHௐDUHௐQRWௐDEOHௐWRௐIXOO\ௐ VXSSRUWௐHLWKHUௐWKURXJKௐRXUௐGHDOHUௐQHWZRUNௐRUௐGLUHFWௐFRYHUDJHௐWKURXJKௐFRYHUDJH 

 ,GHQWLI\ௐDQ\ௐ6RXUFHZHOOௐSDUWLFLSDWLQJௐHQWLW\ௐ
VHFWRUVௐ
LHௐJRYHUQPHQWௐHGXFDWLRQௐQRWIRU
SURILW
ௐWKDWௐ\RXௐZLOOௐ127ௐEHௐIXOO\ௐVHUYLQJௐ
WKURXJKௐWKHௐSURSRVHGௐFRQWUDFWௐ([SODLQௐLQௐ
GHWDLOௐ)RUௐH[DPSOHௐGRHVௐ\RXUௐFRPSDQ\ௐ
KDYHௐRQO\ௐDௐUHJLRQDOௐSUHVHQFHௐRUௐGRௐRWKHUௐ
FRRSHUDWLYHௐSXUFKDVLQJௐFRQWUDFWVௐOLPLWௐ\RXUௐ
DELOLW\ௐWRௐSURPRWHௐDQRWKHUௐFRQWUDFW"
7KHUHௐDUHௐQRௐGHILQHGௐVHFWRUVௐWKDWௐ3LHUFHௐRUௐ$LUSRUWௐ3URGXFWVௐZRXOGௐQRWௐEHௐZLOOLQJௐ DQGௐDEOHௐWRௐVHOOௐWRௐDQGௐH[WHQGௐWKHௐDIWHUௐWKHௐVDOHௐVHUYLFHௐDQGௐVXSSRUWௐZHௐSULGHௐ RXUVHOYHVௐRQ


 'HILQHௐDQ\ௐVSHFLILFௐFRQWUDFWௐUHTXLUHPHQWVௐ
RUௐUHVWULFWLRQVௐWKDWௐZRXOGௐDSSO\ௐWRௐRXUௐ
SDUWLFLSDWLQJௐHQWLWLHVௐLQௐ+DZDLLௐDQGௐ$ODVNDௐ
DQGௐLQௐ86ௐ7HUULWRULHV
3LHUFHௐDQGௐ$LUSRUWௐ3URGXFWVௐLVௐQRWௐDZDUHௐRIௐDQ\ௐVSHFLILFௐFRQWUDFWௐUHTXLUHPHQWVௐRUௐ UHVWULFWLRQVௐWKDWௐDSSO\ௐWRௐPHPEHUVௐ7KRVHௐWHUULWRULHVௐGHWHUPLQHௐZKDWௐFRQWUDFWVௐWKH\ௐ VXSSRUWௐDQGௐDOORZௐWRௐEHௐXVHG 

Bid Number: RFP 113021 Vendor Name: Pierce Manufacturing 













 

EXHIBIT 1 595
7DEOH
0DUNHWLQJ3ODQ
/LQH
,WHP 4XHVWLRQ 5HVSRQVH

 'HVFULEHௐ\RXUௐPDUNHWLQJௐVWUDWHJ\ௐIRUௐ
SURPRWLQJௐWKLVௐFRQWUDFWௐRSSRUWXQLW\ௐௐ
8SORDGௐUHSUHVHQWDWLYHௐVDPSOHVௐRIௐ\RXUௐ
PDUNHWLQJௐPDWHULDOVௐ
LIௐDSSOLFDEOH
ௐLQௐ
WKHௐGRFXPHQWௐXSORDGௐVHFWLRQௐRIௐ\RXUௐ
UHVSRQVH
7KHௐPDUNHWLQJௐVWUDWHJ\ௐZHௐKDYHௐWDNHQௐZLWKௐDOOௐWKHௐDZDUGVௐKDVௐEHJXQௐZLWKௐPDUNHWLQJௐWRௐ RXUௐVDOHVௐIRUFHௐ7KHௐLQLWLDOௐODXQFKௐSURYLGHVௐWKHௐVDOHVௐWHDP

‡ௐ2YHUYLHZௐRIௐWKHௐFRQWUDFWௐDQGௐZKDWௐGLIIHUHQWLDWHVௐLWௐIURPௐWKHௐRWKHUV ‡ௐ7UDLQLQJௐDQGௐXSGDWLQJௐLQWHUQDOௐ8VHUௐ*XLGH+DQGERRN
‡ௐ$GGLQJௐWKHௐFRQWUDFWௐRSWLRQௐWRௐRXUௐFXVWRPௐWUXFNௐFRQILJXUDWRUௐ3XOVH ‡ௐ$GGLQJௐWKHௐFRQWUDFWௐWRௐWKHௐLQWHUQDOௐFRPPXQLFDWLRQௐSRUWDO ‡ௐ8SGDWHௐZZZSLHUFHPIJFRPௐDQGௐZZZRVKNRVKDLUSRUWFRPௐZHEVLWHௐZLWKௐWKHௐDGGLWLRQௐRIௐWKHௐ QHZௐFRQWUDFW
‡ௐ'HYHORSௐDௐIO\HUௐRUௐ)$4ௐWRௐSURYLGHௐVDOHVௐUHSVௐDQGௐFXVWRPHUVௐDVௐDௐWDNHDZD\ ‡ௐ,QFOXGLQJௐDௐ6RXUFHZHOOௐSXUFKDVHGௐWUXFNௐDWௐ3LHUFHௐVKRZVௐ7KHௐ6RXUFHZHOOௐFRQVRUWLXPௐORJRௐ LVௐQRWHGௐRQௐWKHௐFRQILJXUDWLRQௐWKDWௐLVௐGLVSOD\HGௐRQௐWKHௐWUXFNௐ 5HIHUௐWRௐௐ3LHUFHௐ([DPSOHௐ0DUNHWLQJSGIௐLQௐWKHௐ0DUNHWLQJௐ3ODQ6DPSOHVௐIROGHU $GGLWLRQDOௐPDUNHWLQJௐEURFKXUHVௐDYDLODEOHௐLQௐWKHௐ0DUNHWLQJௐ3ODQ6DPSOHVௐIROGHUௐ3OHDVHௐ UHIHUௐWRௐWKHVHௐILOHVௐIRUௐFXUUHQWௐUHSUHVHQWDWLYHௐPDWHULDO 

 'HVFULEHௐ\RXUௐXVHௐRIௐWHFKQRORJ\ௐDQGௐ
GLJLWDOௐGDWDௐ
HJௐVRFLDOௐPHGLDௐ
PHWDGDWDௐXVDJH
ௐWRௐHQKDQFHௐ
PDUNHWLQJௐHIIHFWLYHQHVV
3LHUFHௐKDVௐDௐGHGLFDWHGௐPDUNHWLQJௐWHDPௐWKDWௐPDQDJHVௐRXUௐZHEVLWHௐDQGௐVRFLDOௐPHGLD ௐZHௐ
DOVRௐKDYHௐௐ'HDOHUVௐWKDWௐKDYHௐHVWDEOLVKHGௐZHEVLWHVௐDQGௐXWLOL]HௐVRFLDOௐPHGLDௐSODWIRUPVௐ VXFKௐDVௐWZLWWHUௐ,QVWDJUDPௐDQGௐ)DFHERRNௐWRௐVKDUHௐPHVVDJLQJௐ:HௐDUHௐDEOHௐWRௐWUDFNௐ HQJDJHPHQWௐDQGௐPHWDGDWDௐRQௐRXUௐIROORZHUVௐWKURXJKௐWKHVHௐSODWIRUPVௐௐ1RWௐRQO\ௐLVௐRXUௐ PDUNHWLQJௐWHDPௐZHOOௐYHUVHGௐLQௐORRNLQJௐDWௐLQGXVWU\ௐWUHQGVௐZHௐDOVRௐSDUWQHUௐZLWKௐH[WHUQDOௐ RUJDQL]DWLRQVௐIRUௐDௐPRUHௐUREXVWௐDSSURDFKௐWRௐWHFKQRORJ\ௐௐ %RWKௐ3LHUFHௐDQGௐ$LUSRUWௐ3URGXFWV¶ௐZHEVLWHVௐZLOOௐLQFOXGHௐDZDUGௐDQGௐKDYHௐDௐGLUHFWௐOLQNௐWRௐ WKHௐ6RXUFHZHOOௐZHEVLWHௐZHUHௐIDFWVௐDQGௐLQIRUPDWLRQௐFDQௐEHௐREWDLQHG $LUSRUWௐ3URGXFWVௐDOVRௐXWLOL]HVௐ6KRZSDGௐIRUௐRUJDQL]DWLRQௐDQGௐGLVWULEXWLRQௐRIௐPDUNHWLQJௐ PDWHULDOௐZKLFKௐLVௐDYDLODEOHௐWRௐRXUௐGRPHVWLFௐDQGௐLQWHUQDWLRQDOௐVDOHVௐWHDPௐௐ7KLVௐWRROௐDOORZVௐ XVௐWRௐVKDUHௐLQIRUPDWLRQௐDFURVVௐWKHௐJOREHௐLQFOXGLQJௐLQIRUPDWLRQௐRQௐDYDLODEOHௐSXUFKDVLQJௐ FRQVRUWLXPVௐ7KLVௐWRROௐDOORZVௐXVHUVௐWRௐWUDFNௐFXVWRPHUௐHQJDJHPHQWௐZLWKௐWKHௐPDWHULDO 

 ,Qௐ\RXUௐYLHZௐZKDWௐLVௐ6RXUFHZHOO¶VௐUROHௐ
LQௐSURPRWLQJௐFRQWUDFWVௐDULVLQJௐRXWௐRIௐ
WKLVௐ5)3"ௐ+RZௐZLOOௐ\RXௐLQWHJUDWHௐDௐ
6RXUFHZHOODZDUGHGௐFRQWUDFWௐLQWRௐ\RXUௐ
VDOHVௐSURFHVV"
6RXUFHZHOO¶VௐUROHௐLQௐSURPRWLQJௐWKHௐ)LUHௐ$SSDUDWXVௐFRQWUDFWௐLVௐSULPDULO\ௐDFFHVVLELOLW\ௐWRௐ FXVWRPHUVௐDQGRUௐWKHLUௐSURFXUHPHQWௐRIILFLDOVௐ
6RXUFHZHOO¶ௐVௐUROHௐLVௐWRௐEHௐSDUWQHUௐZLWKௐWKHௐDZDUGHGௐYHQGRUVௐDQGௐXQGHUVWDQGௐWKHௐSURGXFWௐ RQௐWKHௐFRQWUDFWௐVRௐWKDWௐDVௐDௐMRLQWௐHIIRUWௐHQGௐXVHUVௐFDQௐEHௐLQIRUPHGௐDQGௐHGXFDWHGௐRQௐ FRRSHUDWLYHௐSURFXUHPHQWௐDQGௐKRZௐWKLVௐFRQWUDFWௐEHVWௐILWVௐWKHPௐ7KLVௐPD\ௐLQFOXGHௐWUDLQLQJௐ FUHDWLRQௐQHWZRUNLQJௐDWௐDௐVSHFLILFௐVKRZௐRUௐGHDOHUௐORFDWLRQௐ &RRSHUDWLYHௐSURFXUHPHQWௐQHHGVௐWRௐIROGௐLQWRௐWKHௐVDOHVௐSURFHVVௐVKRUWO\ௐDIWHUௐLQWURGXFWLRQVௐ$ௐ 6DOHVௐUHSUHVHQWDWLYHௐVKRXOGௐXQGHUVWDQGௐZKDWௐSURJUDPVௐWKHௐFXVWRPHUௐKDVௐEHHQௐDௐSDUWௐRIௐ DQGRUௐZKDWௐWKH\ௐNQRZௐDERXWௐFRRSHUDWLYHௐSURFXUHPHQWௐSURJUDPVௐDYDLODEOHௐ7KDWௐEDVLFௐ XQGHUVWDQGLQJௐLVௐDௐPXVWௐKDYHௐIURPௐWKHௐRQVHWௐ
7KLVௐSURJUDPௐZRQ¶WௐGHWHUPLQHௐZKDWௐDSSDUDWXVௐWKH\ௐEX\ௐRUௐZKDWௐFXVWRPL]DWLRQௐWKH\ௐFDQௐ KDYHௐ±ௐWKLVௐSURJUDPௐSURYLGHVௐWKHPௐWKHௐDYHQXHௐWRௐJHWௐZKDWௐWKH\ௐQHHGௐWKURXJKௐDQௐHIILFLHQWௐ SURFXUHPHQWௐSURFHVVௐ
)RUௐWKHௐ$LUSRUWௐGLUHFWௐVDOHVௐWHDPௐDOOௐRSSRUWXQLWLHVௐWKDWௐDUHௐQRWௐFRPSHWLWLYHO\ௐELGௐZLOOௐEHௐ SURYLGHGௐLQIRUPDWLRQௐRQௐWKHௐ6RXUFHZHOOௐFRQWUDFWௐDVௐDQௐDYHQXHௐIRUௐSXUFKDVH 

 $UHௐ\RXUௐSURGXFWVௐRUௐVHUYLFHVௐ
DYDLODEOHௐWKURXJKௐDQௐHSURFXUHPHQWௐ
RUGHULQJௐSURFHVV"ௐ,IௐVRௐGHVFULEHௐ\RXUௐ
HSURFXUHPHQWௐV\VWHPௐDQGௐKRZௐ
JRYHUQPHQWDOௐDQGௐHGXFDWLRQDOௐ
FXVWRPHUVௐKDYHௐXVHGௐLW
:HௐGRௐQRWௐRIIHUௐDQௐHSURFXUHPHQWௐRUGHULQJௐSURFHVVௐGXHௐWRௐWKHௐFRPSOH[LW\ௐRIௐRXUௐSURGXFWௐ :HௐKDYHௐGHWHUPLQHGௐWKLVௐSODWIRUPௐGRHVௐQRWௐILWௐLQௐRXUௐEXVLQHVVௐPRGHO 

7DEOH
9DOXH$GGHG$WWULEXWHV
/LQH
,WHP 4XHVWLRQ 5HVSRQVH

Bid Number: RFP 113021 Vendor Name: Pierce Manufacturing 













 

EXHIBIT 1 596

'HVFULEHௐDQ\ௐSURGXFWௐHTXLSPHQWௐ
PDLQWHQDQFHௐRUௐRSHUDWRUௐWUDLQLQJௐ
SURJUDPVௐWKDWௐ\RXௐRIIHUௐWRௐ
6RXUFHZHOOௐSDUWLFLSDWLQJௐHQWLWLHVௐ
,QFOXGHௐGHWDLOVௐVXFKௐDVௐZKHWKHUௐ
WUDLQLQJௐLVௐVWDQGDUGௐRUௐRSWLRQDOௐ
ZKRௐSURYLGHVௐWUDLQLQJௐDQGௐDQ\ௐ
FRVWVௐWKDWௐDSSO\
7UDLQLQJௐLVௐRIIHUHGௐLQௐVHYHUDOௐGLIIHUHQWௐZD\V

‡ௐ$ௐFXVWRPHUௐFDQௐUHTXHVWௐIDFWRU\ௐSHUVRQQHOௐWRௐSURYLGHௐWUDLQLQJௐDQGௐLWௐZLOOௐEHௐDGGHGௐWRௐWKHௐ VDOHௐRUௐDYDLODEOHௐDWௐDௐODWHUௐGDWH
‡ௐ7KHௐGHDOHUௐPD\ௐKDYHௐDௐWUDLQLQJௐSURJUDPௐWRௐRIIHUௐWKDWௐLQWURGXFHVௐWKHௐFXVWRPHUௐWRௐWKHௐ GHDOHU¶VௐVXSSRUWௐWHDP
‡ௐ7KHௐFXVWRPHUௐPD\ௐFKRRVHௐWRௐDWWHQGௐUHJLRQDOௐWUDLQLQJௐFODVVHVௐRIIHUHGௐWKURXJKRXWௐWKHௐ\HDU $OOௐFXVWRPHUVௐUHFHLYHௐDௐ'HOLYHU\ௐ2ULHQWDWLRQௐFODVVௐSULRUௐWRௐSODFLQJௐWKHௐDSSDUDWXVௐLQௐVHUYLFHௐ 2WKHUௐWUDLQLQJௐLVௐRIWHQௐFXVWRPL]HGௐWRௐWKHௐFXVWRPHU¶VௐQHHGVௐDQGௐVFKHGXOHGௐDURXQGௐWKHLUௐ FDOHQGDUVௐ)DFWRU\ௐDQGRUௐ'HDOHUௐWUDLQLQJௐPD\ௐLQFOXGHௐ2SHUDWLRQௐ0DLQWHQDQFHௐ)RDPௐ WUDLQLQJௐ$HULDOௐWUDLQLQJௐ&XVWRPHUௐ0HFKDQLFVௐRUௐFXVWRPL]DEOH 2QVLWHௐWUDLQLQJௐGXULQJௐYHKLFOHௐLQVHUYLFHௐLVௐVWDQGDUGௐௐ7KLVௐSURYLGHVௐDௐEDVLFௐYHKLFOHௐ RSHUDWLRQVௐDQGௐPDLQWHQDQFHௐRYHUYLHZௐௐ7KLVௐWUDLQLQJௐLVௐFRQVLVWHQWௐZLWKௐLQGXVWU\ௐVWDQGDUGVௐௐ 5HIHUௐWRௐ
ௐ3LHUFHௐ7UDLQLQJௐ2IIHULQJVSGIௐLQௐ$GGLWLRQDOௐ'RFXPHQWVௐIRUௐPRUHௐLQIRUPDWLRQௐRQௐ 3LHUFHௐWUDLQLQJௐ
:HௐDOVRௐRIIHUௐDGGLWLRQDOௐWUDLQLQJௐWKURXJKௐRXUௐ2VKNRVKௐ3URGXFWௐ7UDLQLQJௐ&HQWHUௐௐ:HௐKDYHௐ WZRௐULJRURXVௐFRXUVHVௐIRFXVHGௐRQௐWKHௐYHKLFOHVௐFKDVVLVௐDQGௐILUHILJKWLQJௐV\VWHPVௐௐ7KHௐFRVWௐRIௐ DGGLWLRQDOௐPDLQWHQDQFHௐRUௐRSHUDWLRQVௐFRXUVHVௐDUHௐQRWௐLQFOXGHGௐDQGௐVFKHGXOHௐDQGௐSULFLQJௐLVௐ DYDLODEOHௐRQௐRXUௐWUDLQLQJௐZHEVLWHௐ6SHFLDOL]HGௐWUDLQLQJௐFDQௐDOVRௐEHௐUHTXHVWHGௐDQGௐZLOOௐEHௐ TXRWHGௐDWௐWLPHௐRIௐUHTXHVW
KWWSV
RVKNRVKFRUSRUDWLRQFVRGFRP/06FDWDORJ:HOFRPHDVS[ 5HIHUௐWRௐ
ௐ6WULNHUௐ&KDVVLVௐDQGௐ)LUHILJKWLQJௐ0DLQWHQDQFHௐ7UDLQLQJௐ2XWOLQHSGIௐLQௐ$GGLWLRQDOௐ ,QIRUPDWLRQௐIROGHUௐIRUௐ$5))ௐWUDLQLQJௐRXWOLQH


Bid Number: RFP 113021 Vendor Name: Pierce Manufacturing 













 

EXHIBIT 1 597
 'HVFULEHௐDQ\ௐWHFKQRORJLFDOௐ
DGYDQFHVௐWKDWௐ\RXUௐSURSRVHGௐ
SURGXFWVௐRUௐVHUYLFHVௐRIIHU
2VKNRVKௐ&RUSRUDWLRQௐDௐOHDGHUௐLQௐLQQRYDWLRQௐDQGௐHDFKௐRIௐRXUௐSURGXFWVௐDQGௐWHFKQRORJLHVௐLVௐ GHVLJQHGௐZLWKௐFXVWRPHUVௐDQGௐHQGXVHUVௐLQௐPLQGௐLQFOXGLQJௐDGYDQFHVௐLQௐHOHFWULILFDWLRQௐ DXWRQRP\ௐDQGௐDFWLYHௐVDIHW\ௐDQGௐLQWHOOLJHQWௐSURGXFWVௐ/HYHUDJLQJௐWKHௐODWHVWௐLQௐWHFKQRORJ\ௐIRUௐ WRGD\ௐDQGௐWRPRUURZௐDFURVVௐWKHௐGLIIHUHQWௐPDUNHWVௐZHௐVHUYHௐGLIIHUHQWLDWHVௐXVௐDQGௐKHOSVௐXVௐ UHPDLQௐPDUNHWௐOHDGHUVௐDQGௐVWD\ௐDKHDGௐRIௐWKHௐFRPSHWLWLRQௐ$GYDQFLQJௐRXUௐFRPSDQ\ௐLQWRௐQHZௐ PDUNHWVௐDQGௐFDWHJRULHVௐZLOOௐVXSSRUWௐFRQWLQXHGௐJURZWKௐIRUௐWKHௐFRPSDQ\ 7KURXJKௐWKLVௐFRQWUDFWௐZHௐRIIHUௐQXPHURXVௐSURSULHWDU\ௐIHDWXUHVௐWKDWௐVWDQGRXWௐIURPௐRWKHUVௐDQGௐ QRWௐOLPLWHGௐWR

‡ௐ(OHFWULFௐ9HKLFOHVௐௐ3LHUFHௐ0DQXIDFWXULQJௐDQGௐ2VKNRVKௐ$LUSRUWௐ3URGXFWVௐKDYHௐLQWURGXFHGௐ WKHௐ9ROWHUUDŒௐSODWIRUPௐRIௐHOHFWULFௐYHKLFOHVௐIRUௐWKHௐILUHௐDQGௐHPHUJHQF\ௐPDUNHWௐZLWKௐWKHௐILUVWௐ PXQLFLSDOௐWUXFNௐDOUHDG\ௐLQௐVHUYLFHௐZLWKௐWKHௐ&LW\ௐRIௐ0DGLVRQௐ:LVFRQVLQௐௐ7KHௐ6WULNHUŠௐ 9ROWHUUDௐSHUIRUPDQFHௐK\EULGௐ$LUFUDIWௐ5HVFXHௐDQGௐ)LUHௐ)LJKWLQJௐ $5))
ௐYHKLFOHௐLVௐDYDLODEOHௐ
IRUௐGHPRQVWUDWLRQௐDVௐDYDLODEOHௐDWௐFXVWRPHUௐORFDWLRQVௐ 5HIHUௐWRௐௐ9ROWHUUDௐ3UHVVௐ5HOHDVHSGIௐLQௐ$GGLWLRQDOௐ'RFXPHQWVௐIROGHUௐIRUௐPRUHௐ LQIRUPDWLRQௐ
‡ௐ,GOHௐ5HGXFWLRQௐ7HFKQRORJ\ௐ
,57
ௐௐௐ3RZHUௐ1)3$ௐ
ௐUHTXLUHGௐGHYLFHVௐXVHUGHILQHGௐ
PLVVLRQௐFULWLFDOௐRQVFHQHௐORDGVௐDQGௐ+9$&ௐFOLPDWHௐFRQWUROௐZLWKௐWKHௐPDLQௐFKDVVLVௐHQJLQHௐ VKXWௐGRZQௐIRUௐRQHௐKRXUௐRIௐUXQௐWLPHௐDWௐௐDPSVௐ)HDWXULQJௐEXLOWLQௐVDIHW\ௐLQWHUORFNVௐDQGௐ 3LHUFHௐ&RPPDQGௐ=RQHŒௐDXWRVWDUWௐIRUௐEDWWHU\ௐSRZHUௐPRQLWRULQJௐDQGௐHQJLQHௐUHVWDUWௐ GHSDUWPHQWVௐFDQௐZRUNௐPRUHௐVDIHO\ௐDQGௐHIILFLHQWO\ௐZLWKRXWௐDௐVHFRQGௐWKRXJKWௐ3LHUFHௐ,GOHௐ 5HGXFWLRQௐ7HFKQRORJ\ௐLVௐDQௐRSWLRQௐRQௐQHZௐDSSDUDWXVௐDQGௐDVௐDQௐDIWHUPDUNHWௐVROXWLRQ 5HIHUௐWRௐௐ3LHUFH0DQXIDFWXULQJ,GOH5HGXFWLRQ7HFKQRORJ\SGIௐLQௐ$GGLWLRQDOௐ 'RFXPHQWVௐIROGHUௐIRUௐPRUHௐLQIRUPDWLRQௐ
‡ௐ$VFHQGDQWŠௐFODVVௐRIௐDHULDOௐSURGXFWVௐ±ௐ3LHUFHௐSDWHQWHGௐGHVLJQௐWKDWௐRIIHUVௐ ௐRIௐYHUWLFDOௐ
UHDFKௐDQGௐ
ௐRIௐKRUL]RQWDOௐUHDFK
ௐUDWHGௐDWௐDௐௐOEௐ
GU\
ௐௐௐOEௐ
ZHW
ௐWLSௐORDGௐFDSDFLW\ௐ
ZLWKௐDQௐDGGLWLRQDOௐௐOEௐHTXLSPHQWௐDOORZDQFH
ௐIORZௐXSௐWRௐௐJSPௐDQGௐLVௐFDSDEOHௐRIௐDௐ
VWRUHௐIURQWௐEOLW]ௐIHDWXUHௐDVௐVWDQGDUG
‡ௐ3XOVHௐௐ&XVWRPL]HGௐLQKRXVHௐWUXFNௐFRQILJXUDWRUௐWKDWௐDOORZVௐXVௐWRௐEXLOGௐWRௐWKHௐFXVWRPHU¶Vௐ OHYHOௐRIௐFXVWRPL]DWLRQ
‡ௐ7$.Šௐ6XVSHQVLRQௐ±ௐRIIHUVௐVKRUWHUௐVWRSSLQJௐGLVWDQFHௐQRௐEUDNHௐVWHHUௐLPSURYHGௐULGHௐ TXDOLW\ௐDQGௐSURYHQௐWHFKQRORJ\ௐXVHGௐE\ௐWKHௐ86ௐPLOLWDU\ ‡ௐ&RPPDQGௐ=RQHŒௐ,,,ௐHOHFWURQLFVௐ±ௐSURYLGHVௐYHKLFOHௐUHOLDELOLW\ௐHDV\ௐVHUYLFHDELOLW\ௐ\Uௐ VWDQGDUGௐZDUUDQW\
‡ௐ3LHUFHௐ8OWLPDWHௐ&RQILJXUDWLRQௐ
38&Œ
ௐௐ(OLPLQDWHVௐWKHௐSXPSKRXVHௐVRௐ\RXௐFDQௐEXLOGௐ\RXUௐ
DSSDUDWXVௐDURXQGௐ\RXUௐQHHGVௐDQGௐQRWௐWKHௐSXPSௐ,WௐPLQLPL]HVௐYHKLFXODUௐVSDFHௐXVHGௐIRUௐILUHௐ VXSSUHVVLRQௐDQGௐPD[LPL]HVௐVSDFHௐIRUௐHTXLSPHQWௐZKLOHௐVWLOOௐSURYLGLQJௐELJௐSXPSௐIRDPௐDQGௐ &$)6ௐFDSDELOLWLHV
‡ௐ+XVN\ŒௐIRDPௐV\VWHPVௐௐ+\GUDXOLFௐGULYHௐSRZHUHG
ௐ6LQJOHௐSRLQWௐGLUHFWௐLQMHFWLRQௐIORZEDVHGௐ
V\VWHPௐXVLQJௐGLJLWDOௐWHFKQRORJ\ௐWRௐLQGLFDWHௐSXPSௐSRVLWLRQௐDQGௐDௐIORZௐPHWHU ௐDௐEXLOWLQௐIOXVKௐ
V\VWHPௐHTXLSSHGௐZLWKௐDQௐDX[LOLDU\ௐIRDPௐSLFNXS
ௐDௐIRDPௐWDQNௐUHILOOௐV\VWHPௐLVௐDYDLODEOHௐWRௐILOOௐ
WKHௐIRDPௐWDQN
V
ௐIURPௐWKHௐJURXQGௐ
‡ௐ6QR]]OHŠௐ+5(7ௐ±ௐ7KHௐ6QR]]OHௐ+LJKௐ5HDFKௐ([WHQGLEOHௐ7XUUHWௐLVௐDYDLODEOHௐLVௐDௐௐIWௐRUௐௐ IWௐFRQILJXUDWLRQௐௐ2XUௐ+5(7ௐLVௐDYDLODEOHௐRQௐWKHௐ2VKNRVKௐ6WULNHUௐ[ௐ[ௐDQGௐ[ௐ ‡ௐ(FRௐ()3Œௐ)RDPௐ0HDVXUHPHQWௐ6\VWHPௐ±ௐ0HDVXUHௐIRDPௐSHUFHQWDJHVௐIURPௐHYHU\ௐ GLVFKDUJHௐRQௐWKHௐYHKLFOHௐZLWKRXWௐXVLQJௐIRDPௐRQௐWKHௐ2VKNRVKௐ6WULNHUௐYHKLFOHVௐௐ(FRௐ()3ௐ PHDVXUHVௐERWKௐWKHௐVROXWLRQௐDQGௐIRDPௐIORZVௐRQௐWKHௐYHKLFOHௐDQGௐHYHQௐDUFKLYHVௐWKHௐWHVWLQJௐ GDWDௐZLWKௐDௐWLPHௐDQGௐGDWHௐVWDPSௐIRUௐWKUHHௐ\HDUVௐ
5HIHUௐWRௐௐ(FRௐ()3ௐ%URFKXUHSGIௐLQௐ$GGLWLRQDOௐ'RFXPHQWVௐIROGHUௐIRUௐPRUHௐLQIRUPDWLRQௐ 7KHௐ&RPSDQ\¶VௐDGYDQFHGௐGHVLJQௐDQGௐHQJLQHHULQJௐFDSDELOLWLHVௐKDYHௐFRQWULEXWHGௐWRௐWKHௐ GHYHORSPHQWௐRIௐLQQRYDWLYHௐDQGRUௐSURSULHWDU\ௐVHYHUHGXW\ௐFRPSRQHQWVௐWKDWௐHQKDQFHௐYHKLFOHௐ SHUIRUPDQFHௐUHGXFHௐPDQXIDFWXULQJௐFRVWVௐDQGௐVWUHQJWKHQௐFXVWRPHUௐUHODWLRQVKLSVௐ7KHௐ &RPSDQ\¶VௐDGYDQFHGௐGHVLJQௐDQGௐHQJLQHHULQJௐFDSDELOLWLHVௐKDYHௐDOVRௐDOORZHGௐLWௐWRௐLQWHJUDWHௐ PDQ\ௐRIௐWKHVHௐFRPSRQHQWVௐDFURVVௐYDULRXV
VHJPHQWVௐDQGௐSURGXFWௐOLQHVௐZKLFKௐHQKDQFHVௐLWVௐDELOLW\ௐWRௐFRPSHWHௐIRUௐQHZௐEXVLQHVVௐDQGௐ UHGXFHVௐLWVௐFRVWVௐWRௐPDQXIDFWXUHௐLWVௐSURGXFWVௐFRPSDUHGௐWRௐPDQXIDFWXUHUVௐZKRௐVLPSO\ௐ DVVHPEOHௐSXUFKDVHGௐFRPSRQHQWVௐ7KHௐ&RPSDQ\ௐKDVௐEHHQௐDௐVXSSOLHUௐRIௐHOHFWULFSRZHUHGௐ SURGXFWVௐIRUௐPRUHௐWKDQௐௐ\HDUVௐDQGௐUHFHQWO\ௐODXQFKHGௐVHYHUDOௐQHZௐSURGXFWVௐWKDWௐOHYHUDJHௐ ]HURௐHPLVVLRQVௐHOHFWULILFDWLRQௐIRUௐPRELOLW\ௐDFURVVௐDOOௐVHJPHQWV 

Bid Number: RFP 113021 Vendor Name: Pierce Manufacturing 













 

EXHIBIT 1 598
 'HVFULEHௐDQ\ௐ³JUHHQ´ௐLQLWLDWLYHVௐ
WKDWௐUHODWHௐWRௐ\RXUௐFRPSDQ\ௐRUௐWRௐ
\RXUௐSURGXFWVௐRUௐVHUYLFHVௐDQGௐ
LQFOXGHௐDௐOLVWௐRIௐWKHௐFHUWLI\LQJௐ
DJHQF\ௐIRUௐHDFK
2VKNRVKௐ&RUSRUDWLRQௐLQFOXGLQJௐ3LHUFHௐDQGௐLWVௐVLVWHUௐVHJPHQWVௐKDYHௐ(QYLURQPHQWDOௐ3ROLFLHVௐ ௐ3URFHGXUHVௐLQFOXGLQJௐEXWௐQRWௐOLPLWHGௐWRௐDQௐ(QYLURQPHQWDOௐ3URWHFWLRQௐ3ROLF\ௐDQGௐDQௐ (QHUJ\ௐ0DQDJHPHQWௐ3ROLF\ௐ3OHDVHௐUHIHUௐWRௐRXUௐUHVSRQVHௐLQௐTXHVWLRQௐௐRQௐRXUௐUHFHQWௐ DZDUGௐDFKLHYHPHQWVௐDVௐZHOOௐௐ
5HIHUௐWRௐ
ௐB6XVWDLQDELOLW\B5HSRUWSGIௐLQௐWKHௐ)LQDQFLDOௐ6WUHQJWKௐDQGௐ6WDELOLW\ௐIROGHUௐ 3LHUFHௐ6XVWDLQDELOLW\ௐ(IIRUWVௐ
6XVWDLQDELOLW\ௐLVௐGHILQHGௐDVௐ³PHHWLQJௐWKHௐQHHGVௐRIௐWKHௐSUHVHQWௐZLWKRXWௐFRPSURPLVLQJௐWKHௐ DELOLW\ௐRIௐIXWXUHௐJHQHUDWLRQVௐWRௐPHHWௐWKHLUௐRZQௐQHHGV´ௐௐ3LHUFHௐLVௐFRQWLQXRXVO\ௐLPSURYLQJௐKRZௐ ZHௐPDNHௐDQGௐGLVWULEXWHௐSURGXFWVௐ,W¶VௐDERXWௐUHGXFLQJௐWKHௐHQYLURQPHQWDOௐLPSDFWௐRIௐRXUௐ SURGXFWVௐDQGௐSURGXFWLRQௐLPSURYLQJௐZRUNSODFHௐFRQGLWLRQVௐUHGXFLQJௐFRVWVௐLQFUHDVLQJௐYDOXHௐ DQGௐEHLQJௐDFWLYHௐLQௐRXUௐFRPPXQLWLHV
3LHUFHௐKDVௐHVWDEOLVKHGௐZDVWHௐDQGௐHQHUJ\ௐ.H\ௐ3HUIRUPDQFHௐ,QGLFDWRUVௐ .3,V
ௐDQGௐDUHௐ
GHYHORSLQJௐDQGௐLPSOHPHQWLQJௐSODQVௐWRௐPHHWௐWKHVHௐJRDOVௐPRQWKௐRYHUௐPRQWKௐௐ.3,VௐDUHௐ WUDFNHGௐUHFRUGHGௐDQGௐVKDUHGௐPRQWKO\ௐZLWKௐWKHௐWHDPVௐDQGௐRXUௐVLVWHUௐVHJPHQWVௐLQFOXGLQJௐ &RUSRUDWHௐ
2VKNRVKௐ&RUSRUDWLRQௐFRQGXFWVௐLQWHUQDOௐHQYLURQPHQWDOௐDXGLWVௐXVLQJௐDௐWKLUGSDUW\ௐHQYLURQPHQWDOௐ DXGLWLQJௐWRROௐ7KHVHௐDXGLWVௐDUHௐFRPSOHWHGௐRQௐDOOௐVLWHVௐRQௐDௐURWDWLQJௐEDVLVௐ(DFKௐIDFLOLW\ௐLVௐ DXGLWHGௐDWௐOHDVWௐRQFHௐHYHU\ௐWKUHHௐ\HDUVௐௐ
3LHUFHௐLVௐDQௐDFWLYHௐPHPEHUௐRIௐWKHௐ'RZௐ-RQHVௐ6XVWDLQDELOLW\ௐ,QGH[ௐ '-6,

7KHௐ'RZௐ-RQHVௐ6XVWDLQDELOLW\ௐ,QGLFHVௐ
'-6,
ௐODXQFKHGௐLQௐ

ௐDUHௐDௐIDPLO\ௐRIௐLQGLFHVௐ
HYDOXDWLQJௐWKHௐVXVWDLQDELOLW\ௐSHUIRUPDQFHௐRIௐWKHௐODUJHVWௐௐFRPSDQLHVௐOLVWHGௐRQௐWKHௐ'RZௐ -RQHVௐ*OREDOௐ7RWDOௐ6WRFNௐ0DUNHWௐ,QGH[
'HSDUWPHQWௐRIௐ(QHUJ\¶Vௐ%HWWHUௐ%XLOGLQJVௐ%HWWHUௐ3ODQWVௐ3URJUDP 3LHUFHௐDORQJௐZLWKௐWKHௐRWKHUௐ2VKNRVKௐVHJPHQWVௐGHPRQVWUDWHௐRXUௐFRPPLWPHQWௐWRௐLPSURYLQJௐ HQHUJ\ௐSHUIRUPDQFHௐE\ௐVLJQLQJௐDௐYROXQWDU\ௐSOHGJHௐWRௐUHGXFHௐRXUௐHQHUJ\ௐLQWHQVLW\ௐE\ௐௐ RYHUௐDௐWHQ\HDUௐSHULRGௐZLWKௐWKHௐ86ௐ'HSDUWPHQWௐRIௐ(QHUJ\¶Vௐ%HWWHUௐ%XLOGLQJVௐ%HWWHUௐ3ODQWVௐ 3URJUDPௐ/HDGLQJௐPDQXIDFWXUHUVௐDQGௐLQGXVWULDOVFDOHௐHQHUJ\ௐXVLQJௐRUJDQL]DWLRQVௐLPSOHPHQWௐ FRVWHIIHFWLYHௐHQHUJ\ௐHIILFLHQF\ௐLPSURYHPHQWVௐWKDWௐVDYHௐHQHUJ\ௐDQGௐLPSURYHௐFRPSHWLWLYHQHVV ,62ௐ
ௐ(QYLURQPHQWDOௐ0DQDJHPHQWௐ6\VWHP
7RௐIXUWKHUௐVROLGLI\ௐDQGௐVWDQGDUGL]HௐRXUௐHQYLURQPHQWDOௐSHUIRUPDQFHௐ3LHUFHௐ0DQXIDFWXULQJௐDQGௐ WKHௐ$LUSRUWௐ3URGXFWVௐ*URXSௐDUHௐLQௐWKHௐSURFHVVௐRIௐIRUPDOL]LQJௐDQௐ(QYLURQPHQWDOௐ0DQDJHPHQWௐ 6\VWHPௐIRUௐRXUௐ1HHQDKௐPDQXIDFWXULQJௐIDFLOLW\ௐLQௐDFFRUGDQFHௐZLWKௐ,62ௐ ௐ
5HIHUௐWRௐௐ,62ௐௐ2VKNRVKௐ$LUSRUWௐ3URGXFWVSGIௐLQௐ)LQDQFLDOௐ6WUHQJWKௐDQGௐ6WDELOLW\ௐ IROGHUௐௐ
&RPPXQLW\ௐ±ௐ*RRGZLOO
3LHUFHௐZRUNVௐZLWKௐWKHௐORFDOௐ*RRGZLOOௐLQௐPDQ\ௐGLIIHUHQWௐIDFHWVௐ2QHௐLVௐWKHௐUHXVHௐRIௐRXUௐVDIHW\ௐ JODVVHVௐ2XUௐIULHQGVௐDWௐ*RRGZLOOௐFOHDQௐDQGௐUHSDFNDJHௐWKHௐJODVVHVௐIRUௐUHXVHௐDWௐRXUௐIDFLOLWLHVௐ ,WௐLVௐDௐFRVWௐVDYLQJVௐEXWௐPRVWௐLPSRUWDQWO\ௐLWௐLVௐKHOSLQJௐRXUௐFRPPXQLW\ௐDQGௐUHGXFLQJௐZDVWHௐWRௐ ODQGILOO


Bid Number: RFP 113021 Vendor Name: Pierce Manufacturing 













 

EXHIBIT 1 599
 ,GHQWLI\ௐDQ\ௐWKLUGSDUW\ௐLVVXHGௐHFR
ODEHOVௐUDWLQJVௐRUௐFHUWLILFDWLRQVௐWKDWௐ
\RXUௐFRPSDQ\ௐKDVௐUHFHLYHGௐIRUௐ
WKHௐHTXLSPHQWௐRUௐSURGXFWVௐ
LQFOXGHGௐLQௐ\RXUௐ3URSRVDOௐUHODWHGௐ
WRௐHQHUJ\ௐHIILFLHQF\ௐRUௐ
FRQVHUYDWLRQௐOLIHF\FOHௐGHVLJQௐ

FUDGOHWRFUDGOH
ௐRUௐRWKHUௐ
JUHHQVXVWDLQDELOLW\ௐIDFWRUV
3LHUFHௐ0DQXIDFWXULQJௐKDVௐUHFHLYHGௐFHUWLILFDWLRQVௐDQGௐDZDUGVௐWRZDUGVௐRXUௐFRPPLWPHQWௐWRௐ HQHUJ\ௐHIILFLHQF\ௐFRQVHUYDWLRQௐDQGௐVXVWDLQDELOLW\ௐௐ$OOௐFHUWLILFDWLRQVௐDQGௐDZDUGVௐDUHௐGULYHQௐ WKURXJKௐ.H\ௐSHUIRUPDQFHௐ,QGLFDWRUVௐ
.3,V
ௐDXGLWLQJௐDQGௐFRQWLQXRXVௐSHUIRUPDQFHௐWKURXJKRXWௐ
WKHௐ3LHUFHௐIDPLO\ௐDQGௐ2VKNRVKௐ&RUSRUDWLRQௐௐ&HUWLILFDWLRQVௐDQGௐDZDUGVௐDUHௐDWWDFKHGௐDQGௐ OLQNHGௐIRUௐUHIHUHQFHௐௐ
&(57,),&$7,216

,62ௐ
ௐ&HUWLILFDWLRQ
2XUௐ1HHQDKௐ:,ௐIDFLOLW\ௐKDVௐUHFHLYHGௐWKHௐ,62ௐ
ௐFHUWLILFDWLRQௐGHPRQVWUDWLQJௐRXUௐ
VWURQJௐFRPPLWPHQWௐWRௐSHUIRUPDQFHௐLPSOHPHQWDWLRQௐRIௐDௐZRUOGFODVVௐHQYLURQPHQWDOௐ PDQDJHPHQWௐV\VWHPௐDQGௐFRPSOHWLRQௐRIௐDௐULJRURXVௐWKLUGSDUW\ௐHYDOXDWLRQ 758(ௐ=HURௐ:DVWHௐ&HUWLILFDWLRQ
7KHௐ7RWDOௐ5HVRXUFHௐ8VHௐDQGௐ(IILFLHQF\ௐ
758(
ௐ=HURௐ:DVWHௐFHUWLILFDWLRQௐSURJUDPௐ
DGPLQLVWHUHGௐE\ௐ*UHHQௐ%XVLQHVVௐ&HUWLILFDWLRQௐ,QFௐSURYLGHVௐULJRURXVௐWKLUGSDUW\ௐFHUWLILFDWLRQௐ IRUௐ]HURௐZDVWHௐJRDOVௐ)DFLOLWLHVௐHDUQௐFUHGLWVௐWRZDUGௐFHUWLILFDWLRQௐIRUௐDFWLYLWLHVௐLQௐUHGHVLJQLQJௐ SURFHVVHVௐUHGXFLQJௐZDVWHௐUHXVLQJௐPDWHULDOVௐDQGௐILQGLQJௐVROXWLRQVௐRWKHUௐWKDQௐODQGILOOௐIRUௐ ZDVWHௐ2XUௐ1HHQDKௐ:,ௐIDFLOLW\ௐKDVௐDFKLHYHGௐ758(ௐFHUWLILFDWLRQௐDWௐWKHௐ*ROGௐ/HYHO $:$5'6

7KHௐDGYDQFHVௐ3LHUFHௐKDVௐPDGHௐLQௐVXVWDLQDEOHௐSUDFWLFHVௐWKXVௐIDUௐKDYHௐEHHQௐUHFRJQL]HGௐE\ௐ QXPHURXVௐDJHQFLHVௐERWKௐJRYHUQPHQWDOௐDQGௐSULYDWHௐ$GGLWLRQDOO\ௐZHௐKDYHௐREWDLQHGௐ FHUWLILFDWLRQVௐDQGௐMRLQHGௐSURJUDPVௐZKLFKௐVHUYHௐDVௐSOHGJHVௐWRௐRXUௐFRQWLQXRXVௐLPSURYHPHQWௐLQௐ VXVWDLQDELOLW\ௐDQGௐHQYLURQPHQWDOௐVWHZDUGVKLSௐ7KHௐPDMRULW\ௐRIௐWKHௐDZDUGVௐUHIHUHQFHGௐEHORZௐ \RXௐZLOOௐDOVRௐILQGௐLQௐWKHௐWDEOHௐௐTXHVWLRQௐ
(QHUJ\ௐ(IILFLHQF\ௐ([FHOOHQFHௐ$ZDUG
7KHௐ(QHUJ\ௐ(IILFLHQF\ௐ([FHOOHQFHௐ$ZDUGௐUHFRJQL]HVௐEXVLQHVVௐSDUWLFLSDQWVௐRIௐ)RFXVௐRQௐ (QHUJ\ௐ:LVFRQVLQ¶VௐVWDWHZLGHௐHQHUJ\ௐHIILFLHQF\ௐDQGௐUHQHZDEOHௐUHVRXUFHVௐSURJUDPௐZKRௐ KDYHௐGHPRQVWUDWHGௐDQௐRXWVWDQGLQJௐFRPPLWPHQWௐWRௐUHGXFLQJௐHQHUJ\ௐZDVWHௐE\ௐLPSOHPHQWLQJௐ HQHUJ\VDYLQJௐXSJUDGHVௐLQௐWKHLUௐIDFLOLWLHVௐDQGௐRSHUDWLRQVௐ,Qௐௐ3LHUFHௐZDVௐKRQRUHGௐZLWKௐ WKLVௐDZDUGௐIRUௐRXUௐHIIRUWVௐLQௐUHGXFLQJௐHQHUJ\ௐLQௐRXUௐSURGXFWVௐDQGௐSURGXFWLRQ :LVFRQVLQௐ5HF\FOLQJௐ([FHOOHQFHௐ$ZDUG
7KHௐ'HSDUWPHQWௐRIௐ1DWXUDOௐ5HVRXUFHVௐUHFRJQL]HVௐRXWVWDQGLQJௐUHF\FOLQJௐDQGௐZDVWHௐ PLQLPL]DWLRQௐHIIRUWVௐWKURXJKௐLWVௐDQQXDOௐ5HF\FOLQJௐ([FHOOHQFHௐ$ZDUGௐSURJUDPௐ3LHUFHௐUHFHLYHGௐ WKHௐ2YHUDOOௐ3URJUDPௐ$ZDUGௐLQௐௐIRUௐRXUௐGLYHUVHௐDQGௐH[WHQVLYHௐZDVWHௐUHGXFWLRQௐHIIRUWV *5((1ௐௐ6867$,1$%,/,7<

'RZௐ-RQHVௐ6XVWDLQDELOLW\ௐ,QGH[
2XUௐVXVWDLQDELOLW\ௐHIIRUWVௐKDYHௐEHHQௐUHFRJQL]HGௐWKURXJKௐRXUௐLQFOXVLRQௐRQௐWKHௐ'RZௐ-RQHVௐ 6XVWDLQDELOLW\ௐ:RUOGௐ,QGH[ௐ
'-6,
ௐ7KHௐ'-6,ௐLVௐDௐIDPLO\ௐRIௐEHVWLQFODVVௐEHQFKPDUNVௐZKLFKௐ WUDFNௐWKHௐVWRFNௐSHUIRUPDQFHௐRIௐWKHௐZRUOG¶VௐOHDGLQJௐFRPSDQLHVௐLQௐWHUPVௐRIௐHFRQRPLFௐ HQYLURQPHQWDOௐDQGௐVRFLDOௐFULWHULDௐௐPDUNHGௐWKHௐWKLUGௐFRQVHFXWLYHௐ\HDUௐZHௐZHUHௐQDPHGௐ WRௐWKHௐ,QGH[ௐKLJKOLJKWLQJௐRXUௐFRPPLWPHQWௐWRௐVXVWDLQDEOHௐEXVLQHVVௐSUDFWLFHV :RUOG¶Vௐ0RVWௐ(WKLFDOௐ&RPSDQLHV
,QௐௐZHௐFHOHEUDWHGௐRXUௐVL[WKௐFRQVHFXWLYHௐ\HDUௐEHLQJௐQDPHGௐRQHௐRIௐWKHௐ:RUOG¶Vௐ0RVWௐ (WKLFDOௐ&RPSDQLHVௐE\ௐ(WKLVSKHUHŒௐ7KHௐDVVHVVPHQWௐFRQVLGHUVௐRYHUௐௐGDWDௐSRLQWVௐRQௐ FXOWXUHௐHQYLURQPHQWDOௐDQGௐVRFLDOௐSUDFWLFHVௐHWKLFVௐDQGௐFRPSOLDQFHௐDFWLYLWLHVௐGLYHUVLW\ௐDQGௐ LQFOXVLRQௐDQGௐLQLWLDWLYHVௐWRௐVXSSRUWௐDௐVWURQJௐYDOXHௐFKDLQ *UHHQௐ0DVWHUV
7KHௐ*UHHQௐ0DVWHUVௐ3URJUDPௐLVௐDQௐDVVHVVPHQWௐDQGௐUHFRJQLWLRQௐSURJUDPௐIRUௐ:LVFRQVLQௐ EXVLQHVVHVௐLQWHUHVWHGௐLQௐLPSURYLQJௐDQGௐEHLQJௐUHFRJQL]HGௐIRUௐWKHLUௐVXVWDLQDELOLW\ௐLQLWLDWLYHVௐ ௐPDUNHGௐWKHௐVHYHQWKௐFRQVHFXWLYHௐ\HDUௐZHௐZHUHௐGHHPHGௐDௐ*UHHQௐ0DVWHUௐLQGLFDWLQJௐ WKDWௐZHௐDUHௐLQௐWKHௐWRSௐௐRIௐFRPSDQLHVௐHYDOXDWHG


 'HVFULEHௐDQ\ௐ:RPHQௐRUௐ0LQRULW\ௐ
%XVLQHVVௐ(QWLW\ௐ
:0%(
ௐ6PDOOௐ
%XVLQHVVௐ(QWLW\ௐ
6%(
ௐRUௐYHWHUDQௐ
RZQHGௐEXVLQHVVௐFHUWLILFDWLRQVௐWKDWௐ
\RXUௐFRPSDQ\ௐRUௐKXEௐSDUWQHUVௐ
KDYHௐREWDLQHGௐ8SORDGௐ
GRFXPHQWDWLRQௐRIௐFHUWLILFDWLRQௐ
DVௐ

DSSOLFDEOH
ௐLQௐWKHௐGRFXPHQWௐ
XSORDGௐVHFWLRQௐRIௐ\RXUௐUHVSRQVH
2VKNRVKௐ&RUSRUDWLRQௐLVௐDௐODUJHௐSXEOLFO\ௐWUDGHGௐFRPSDQ\ௐDQGௐGRHVௐQRWௐTXDOLI\ௐIRUௐGLYHUVLW\ௐ FHUWLILFDWLRQVௐ+RZHYHUௐௐDVௐDQௐRUJDQL]DWLRQௐ2VKNRVKௐLVௐDௐPHPEHUௐRIௐ1DWLRQDOௐ0LQRULW\ௐ 6XSSOLHUௐ'HYHORSPHQWௐ&RXQFLOௐ
106'&
ௐௐ$Wௐ2VKNRVKௐ&RUSRUDWLRQௐZHௐDUHௐDERXWௐEXLOGLQJௐ
SURWHFWLQJௐDQGௐVHUYLQJௐFRPPXQLWLHVௐWKURXJKRXWௐWKHௐJOREHௐ:HௐDUHௐFRPPLWWHGௐWRௐZRUNLQJௐZLWKௐ DௐGLYHUVHௐVXSSO\ௐEDVHௐWKDWௐLVௐUHSUHVHQWDWLYHௐRIௐRXUௐFXVWRPHUVௐDQGௐWKHௐFRPPXQLWLHVௐZHௐVHUYH 5HIHUௐWRௐௐ2VKNRVKௐ6XSSOLHUௐ'LYHUVLW\SGIௐLQௐ$GGLWLRQDOௐ'RFXPHQWVௐIRUௐPRUHௐLQIRUPDWLRQ 

 :KDWௐXQLTXHௐDWWULEXWHVௐGRHVௐ\RXUௐ
FRPSDQ\ௐ\RXUௐSURGXFWVௐRUௐ\RXUௐ
VHUYLFHVௐRIIHUௐWRௐ6RXUFHZHOOௐ
SDUWLFLSDWLQJௐHQWLWLHV"ௐ:KDWௐPDNHVௐ
\RXUௐSURSRVHGௐVROXWLRQVௐXQLTXHௐLQௐ
\RXUௐLQGXVWU\ௐDVௐLWௐDSSOLHVௐWRௐ
6RXUFHZHOOௐSDUWLFLSDWLQJௐHQWLWLHV"
2VKNRVKௐ&RUSRUDWLRQௐLVௐDௐWUXVWHGௐSDUWQHUௐZLWKௐRYHUௐௐ\HDUVௐLQௐEXVLQHVVௐIRFXVHGௐRQௐ LQQRYDWLRQௐZLWKௐWKHௐFXVWRPHUௐLQௐPLQGௐ:LWKௐRXUௐZRUNௐLQௐHOHFWULILFDWLRQௐDQGௐLQWHOOLJHQWௐSURGXFWVௐ ZHௐZLOOௐFRQWLQXHௐWRௐOHDGௐLQௐWKHௐVSHFLDOW\ௐWUXFNௐPDQXIDFWXULQJௐPDUNHWௐௐ2XUௐFXVWRPHUVௐEHQHILWௐ IURPௐWKHௐVL]HௐDQGௐVFDOHௐRIௐDௐODUJHௐRUJDQL]DWLRQௐ\HWௐUHFHLYHௐIRFXVHGௐDWWHQWLRQௐIURPௐRXUௐ VXEVLGLDULHVௐDQGௐWKHLUௐUHVSHFWLYHௐGHDOHUVKLSVௐ
3LHUFHௐLVௐDௐOHDGLQJௐPDQXIDFWXUHUௐRIௐFXVWRPL]HGௐILUHௐDSSDUDWXVௐZLWKௐDௐGHDOHUௐQHWZRUNௐVHFRQGௐ WRௐQRQHௐ7KHௐORQJHYLW\ௐVWDELOLW\ௐDQGௐIDPLO\ௐWUDGLWLRQௐLQௐWKHௐILUHௐLQGXVWU\ௐWKDWௐLVௐWKUHDGHGௐ WKURXJKRXWௐRXUௐGHDOHUௐQHWZRUNௐVHWVௐXVௐDSDUWௐIURPௐRWKHUVௐ2XUௐSDUWQHUVKLSௐZLWKௐWKHௐRWKHUௐ VHJPHQWVௐZLWKLQௐWKHௐ2VKNRVKௐ&RUSRUDWLRQௐDQGௐWKHௐEDFNLQJௐRIௐRXUௐSDUHQWௐFRPSDQ\ௐ2VKNRVKௐ &RUSRUDWLRQௐOHYHUDJHVௐLQQRYDWLRQௐDQGௐILQDQFLDOௐVWUHQJWKௐ 3LHUFHௐXQGHUVWDQGVௐWKHௐFXVWRPHU¶VௐQHHGVௐDQGௐSURYLGHVௐWKHௐGHWDLOௐWKHௐFRPPLWPHQWௐDQGௐWKHௐ IROORZௐWKURXJKௐORQJௐDIWHUௐWKHௐDSSDUDWXVௐLVௐGHOLYHUHGௐ
2VKNRVKௐ$LUSRUWௐ3URGXFWVௐFRPSOHWHVௐWKHௐIXOOௐSURGXFWVௐVXSSRUWHGௐE\ௐWKLVௐFRQWUDFWௐWKURXJKௐLWVௐ 2VKNRVKௐ6WULNHUௐ$5))ௐௐ$LUSRUWௐ3URGXFWVௐLVௐGHGLFDWHGௐWRௐOHDGLQJௐWKHௐZD\ௐLQௐWHFKQRORJ\ௐ SURGXFWௐVXSSRUWௐDQGௐFXVWRPHUௐVHUYLFHௐLQௐWKHௐ$5))ௐPDUNHW 

Bid Number: RFP 113021 Vendor Name: Pierce Manufacturing 













 

EXHIBIT 1 600
7DEOH

:DUUDQW\
'HVFULEHLQGHWDLO\RXUPDQXIDFWXUHUZDUUDQW\SURJUDPLQFOXGLQJFRQGLWLRQVDQGUHTXLUHPHQWVWRTXDOLI\FODLPVSURFHGXUH DQGRYHUDOOVWUXFWXUH<RXPD\XSORDGUHSUHVHQWDWLYHVDPSOHVRI\RXUZDUUDQW\PDWHULDOV LIDSSOLFDEOH
LQWKHGRFXPHQW
XSORDGVHFWLRQRI\RXUUHVSRQVHLQDGGLWLRQWRUHVSRQGLQJWRWKHTXHVWLRQVEHORZ /LQH
,WHP 4XHVWLRQ 5HVSRQVH

 'Rௐ\RXUௐZDUUDQWLHVௐFRYHUௐDOOௐSURGXFWVௐSDUWVௐDQGௐ
ODERU"
<HVௐ2XUௐRQH\HDUௐEXPSHUௐWRௐEXPSHUௐZDUUDQW\ௐFRYHUVௐDOOௐSURGXFWௐSDUWVௐDQGௐ ODERUௐ3LHUFHௐWKHௐ³PDQXIDFWXUHU´ௐZDUUDQWVௐHDFKௐQHZO\ௐPDQXIDFWXUHGௐILUHௐ DSSDUDWXVௐWRௐWKHௐRULJLQDOௐHQGௐXVHUSXUFKDVHUௐRIௐVSHFLILHGௐSHULRGVௐVWDWHGௐ EHORZௐIURPௐWKHௐGDWHௐRIௐGHOLYHU\
7KHௐVWDQGDUGௐ&DEௐ ௐFKDVVLVௐZDUUDQW\ௐSURYLGHVௐDௐRQH\HDUௐZDUUDQW\ௐWKDWௐ ZDUUDQWVௐDJDLQVWௐGHIHFWVௐLQௐSURGXFWௐZRUNPDQVKLSௐDQGRUௐGHVLJQௐ7KLVௐ ZDUUDQW\ௐVKDOOௐDSSO\ௐSURYLGHGௐWKHௐYHKLFOHௐLVௐSURSHUO\ௐPDLQWDLQHG 1RWKLQJௐFRQWDLQHGௐLQௐWKLVௐZDUUDQW\ௐVKDOOௐPDNHௐWKHௐ0DQXIDFWXUHUௐOLDEOHௐEH\RQGௐ WKHௐH[SUHVVௐOLPLWDWLRQVௐKHUHRIௐIRUௐORVVௐLQMXU\ௐRUௐGDPDJHௐRIௐDQ\ௐNLQGௐWRௐDQ\ௐ SHUVRQௐRUௐHQWLW\ௐUHVXOWLQJௐGHIHFWௐRUௐIDLOXUHௐRIௐWKHௐSURGXFWௐ H[FHSWௐDVௐFRYHUHGௐ
E\ௐ3URGXFWௐOLDELOLW\ௐLQVXUDQFH
ௐ
5HIHUௐWRௐௐ:$ௐௐ3LHUFHௐௐ\HDUSGIௐDQGௐௐ2VKNRVKௐௐ <HDUௐ%DVLFௐ9HKLFOHௐ:DUUDQW\SGIௐLQௐWKHௐ:DUUDQW\ௐIROGHUௐIRUௐRXUௐVWDQGDUGௐௐ \HDUௐZDUUDQW\ௐ
7KHௐ0DQXIDFWXUHU¶VௐZDUUDQW\ௐVKDOOௐQRWௐDSSO\ௐWRௐWKHௐIROORZLQJ

‡ௐ:HDUௐLWHPV
‡ௐ1RUPDOௐDGMXVWPHQWVௐDQGௐPDLQWHQDQFHௐVHUYLFHV
‡ௐ)DLOXUHVௐUHVXOWLQJௐIURPௐWKHௐSURGXFWௐEHLQJௐRSHUDWHGௐLQௐDௐPDQQHUௐQRWௐLQௐ DFFRUGDQFHௐZLWKௐWKHௐRSHUDWLRQௐPDQXDOௐRUௐIRUௐDௐSXUSRVHௐQRWௐUHFRPPHQGHGௐ E\ௐWKHௐ0DQXIDFWXUHU
‡ௐ$Q\ௐSURGXFWௐZKLFKௐVKDOOௐKDYHௐEHHQௐUHSDLUHGௐPRGLILHGௐRUௐDOWHUHGௐLQௐDQ\ௐ ZD\ௐWRௐKDYHௐEHHQௐDGYHUVHO\ௐDIIHFWHGௐWKHௐXQLW¶VௐVWDELOLW\ௐRUௐUHOLDELOLW\ ‡ௐ,WHPVௐVXEMHFWHGௐWRௐPLVXVHௐQHJOLJHQFHௐDFFLGHQWௐRUௐLPSURSHUௐPDLQWHQDQFH ‡ௐ/RVVௐRIௐWLPHௐRUௐXVHௐRIௐWKHௐSURGXFWௐLQFRQYHQLHQFHௐRUௐRWKHUௐLQFLGHQWDOௐ H[SHQVHV
7KHௐDXWKRUL]HGௐ3LHUFHௐGHDOHUௐPDQDJHVௐDOOௐZDUUDQW\ௐLVVXHVௐRQௐEHKDOIௐRIௐWKHௐ HQGௐFXVWRPHUௐ7KHௐ3LHUFHௐGHDOHUௐXWLOL]HVௐDQௐRQOLQHௐFODLPௐILOLQJௐV\VWHPௐNQRZQௐ DVௐ2QHௐ:DUUDQW\ௐIRUௐFODLPௐSURFHVVLQJௐ3UHDSSURYDOௐIRUௐDௐFODLPௐRUௐUHTXHVWௐ IRUௐFUHGLWௐ
SRVWௐFRUUHFWLRQௐFODLP
ௐFDQௐEHௐILOHGௐYLDௐWKHௐ2QHௐ:DUUDQW\ௐV\VWHPௐ
LQௐWKHௐHYHQWௐDௐZDUUDQWDEOHௐIDLOXUHௐLVௐIRXQGௐ
$OOௐ6WDQGDUGௐDQGௐ([WHQGHGௐ:DUUDQW\ௐFODLPVௐDUHௐVXEMHFWௐWRௐVSHFLILFௐ6WDQGDUGௐ DQGௐ([WHQGHGௐ:DUUDQW\ௐJXLGHOLQHVௐ6SHFLILFௐZDUUDQWLHVௐH[LVWௐIRUௐSDUWLFXODUௐ PDNHVௐPRGHOVௐFKDVVLVௐRSWLRQVௐHWFௐIRUௐ3LHUFHௐSURGXFWVௐ6SHFLILFௐZDUUDQW\ௐ EXOOHWLQVௐDUHௐSURYLGHGௐDWௐWLPHௐRIௐVDOHௐWRௐWKHௐHQGௐFXVWRPHUௐ 5HIHUௐWRௐDௐVDPSOLQJௐRIௐRXUௐRWKHUௐZDUUDQW\ௐVWDWHPHQWVௐDQGௐPDQXIDFWXUHUV ௐ
VWDWHPHQWVௐRQௐHQJLQHVௐWUDQVPLVVLRQVௐZDWHUௐSXPSௐHWFௐLQௐWKHௐ:DUUDQW\ௐ IROGHUௐௐ$ௐVXPPDU\ௐRIௐZDUUDQW\ௐLVௐDOVRௐDYDLODEOHௐௐ:DUUDQW\ௐ2YHUYLHZSGI 

 'Rௐ\RXUௐZDUUDQWLHVௐLPSRVHௐXVDJHௐUHVWULFWLRQVௐRUௐ
RWKHUௐOLPLWDWLRQVௐWKDWௐDGYHUVHO\ௐDIIHFWௐFRYHUDJH"
:HௐGRௐKDYHௐVRPHௐEDVHௐDQGௐH[WHQGHGௐZDUUDQWLHVௐWKDWௐKDYHௐPLOHDJHௐ OLPLWDWLRQVௐVHWௐWRௐWKHPௐ/LPLWDWLRQVௐYDULHVௐEDVHGௐRQௐWKHௐRSWLRQVௐRIௐWKHௐ YHKLFOHௐ
([DPSOHVௐRIௐEDVHௐZDUUDQWLHVௐDUHௐRXUௐVWUXFWXUDOௐZDUUDQWLHVௐZKLFKௐFDUU\ௐDௐ PLOHௐOLPLWௐௐ
([WHQGHGௐZDUUDQWLHVௐFDUU\ௐYDULRXVௐPLOHDJHௐOLPLWVௐEDVHGௐRQௐWKHௐVSHFLILFௐ FRYHUDJHௐ
3DLQWௐZDUUDQWLHVௐDUHௐSURUDWHGௐEDVHGௐRQௐDJHௐRIௐWKHௐXQLW 

 'Rௐ\RXUௐZDUUDQWLHVௐFRYHUௐWKHௐH[SHQVHௐRIௐ
WHFKQLFLDQV¶ௐWUDYHOௐWLPHௐDQGௐPLOHDJHௐWRௐSHUIRUPௐ
ZDUUDQW\ௐUHSDLUV"
:HௐSULGHௐRXUVHOYHVௐZLWKௐWKHௐFRYHUDJHௐZHௐKDYHௐDFURVVௐWKHௐQDWLRQௐ7KHUHௐDUHௐ QRௐDUHDVௐWKDWௐZHௐGRௐQRWௐKDYHௐFRYHUDJHௐWKURXJKRXWௐ86ௐRUௐ&DQDGDௐ:DUUDQW\ௐ LVௐPDQDJHGௐWKURXJKௐRXUௐ3LHUFHௐDXWKRUL]HGௐGHDOHUVௐDQGௐGHDOHUௐWUDYHOௐ H[SHQVHVௐDUHௐFRYHUHGௐSHUௐRXUௐHVWDEOLVKHGௐLQWHUQDOௐ2QHௐ:DUUDQW\ௐJXLGHOLQHVௐௐ $LUSRUWௐ3URGXFWVௐZDUUDQW\ௐLVௐPDQDJHGௐWKURXJKௐDXWKRUL]HGௐVHUYLFH UHSUHVHQWDWLYHVௐRUௐRXUௐLQWHUQDOௐUHVRXUFHVௐ7UDYHOௐH[SHQVHVௐDUHௐFRYHUHGௐSHUௐ RXUௐHVWDEOLVKHGௐLQWHUQDOௐRQHௐ:DUUDQW\ௐJXLGHOLQHV


 $UHௐWKHUHௐDQ\ௐJHRJUDSKLFௐUHJLRQVௐRIௐWKHௐ8QLWHGௐ
6WDWHVௐRUௐ&DQDGDௐ
DVௐDSSOLFDEOH
ௐIRUௐZKLFKௐ\RXௐ
FDQQRWௐSURYLGHௐDௐFHUWLILHGௐWHFKQLFLDQௐWRௐSHUIRUPௐ
ZDUUDQW\ௐUHSDLUV"ௐௐ+RZௐZLOOௐ6RXUFHZHOOௐ
SDUWLFLSDWLQJௐHQWLWLHVௐLQௐWKHVHௐUHJLRQVௐEHௐSURYLGHGௐ
VHUYLFHௐIRUௐZDUUDQW\ௐUHSDLU"
3LHUFHௐSULGHVௐWKHPVHOYHVௐLQௐWKHௐFRYHUDJHௐZHௐKDYHௐDFURVVௐWKHௐQDWLRQௐ3LHUFHௐ UHTXLUHVௐDௐFHUWLILHGௐWHFKQLFLDQௐIRUௐHDFKௐDUHDௐ7KHUHIRUHௐZHௐDUHௐWRௐVXSSRUWௐDOOௐ UHJLRQVௐWKURXJKRXWௐ86ௐRUௐ&DQDGDௐ$LUSRUWௐ3URGXFWVௐZLOOௐSURYLGHௐVHUYLFHௐ WKURXJKௐLQWHUQDOௐRUௐH[WHUQDOௐVHUYLFHௐUHSUHVHQWDWLYHV 

Bid Number: RFP 113021 Vendor Name: Pierce Manufacturing 













 

EXHIBIT 1 601

:LOOௐ\RXௐFRYHUௐZDUUDQW\ௐVHUYLFHௐIRUௐLWHPVௐPDGHௐE\ௐ
RWKHUௐPDQXIDFWXUHUVௐWKDWௐDUHௐSDUWௐRIௐ\RXUௐSURSRVDOௐ
RUௐDUHௐWKHVHௐZDUUDQWLHVௐLVVXHVௐW\SLFDOO\ௐSDVVHGௐRQௐ
WRௐWKHௐRULJLQDOௐHTXLSPHQWௐPDQXIDFWXUHU"
0DMRUௐFRPSRQHQWVௐLQVWDOOHGௐEXWௐQRWௐPDQXIDFWXUHGௐE\ௐ3LHUFHௐRUௐ$LUSRUWௐ 3URGXFWVௐDUHௐFRYHUHGௐXQGHUௐRULJLQDOௐHTXLSPHQWௐPDQXIDFWXUHU¶VௐZDUUDQWLHVௐ SDVVHGௐWKURXJKௐWRௐHQGௐXVHUFXVWRPHUௐௐ7KHVHௐLQFOXGHௐEXWௐDUHௐQRWௐOLPLWHGௐWRௐ HQJLQHௐWUDQVPLVVLRQௐZDWHUௐSXPSௐ$%6ௐDQGௐD[OHVௐௐ
&RPSRQHQWௐ:DUUDQWLHVௐ
,QௐVRPHௐFDVHVௐVXSSOLHUVௐZLOOௐRIIHUௐZDUUDQWLHVௐEH\RQGௐWKHௐ3LHUFHௐRUௐ$LUSRUWௐ 3URGXFWVௐRQH\HDUௐZDUUDQW\ௐ:DUUDQWLHVௐSURYLGHGௐE\ௐLQGLYLGXDOௐVXSSOLHUVௐRWKHUௐ WKDQௐ3LHUFHௐRUௐ$LUSRUWௐ3URGXFWVௐDSSO\ௐDIWHUௐWKHௐRQH\HDUௐYHKLFOHௐZDUUDQW\ௐ 7KHௐDGPLQLVWUDWLRQௐRIௐLQGLYLGXDOௐVXSSOLHUௐZDUUDQWLHVௐSHUௐWKHௐVXSSOLHUௐDUHௐWRௐ EHௐDGGUHVVHGௐGLUHFWO\ௐZLWKௐWKHௐVXSSOLHUௐWKHPVHOYHV


 :KDWௐDUHௐ\RXUௐSURSRVHGௐH[FKDQJHௐDQGௐUHWXUQௐ
SURJUDPVௐDQGௐSROLFLHV"
3LHUFHௐRIIHUVௐDௐUHWXUQH[FKDQJHௐSURJUDPௐIRUௐDIWHUPDUNHWௐSDUWVௐRQO\ௐWRௐWKHௐ SXUFKDVHUௐ
3LHUFHௐGHDOHU
ௐDQGௐWKHௐGHDOHUௐPD\ௐH[WHQGௐWKLVௐDQGௐRWKHUௐWHUPVௐ
DQGௐFRQGLWLRQVௐWRௐWKHௐHQGௐFXVWRPHU
$IWHUPDUNHWௐ3DUWVௐ:DUUDQW\
3LHUFHௐDQGௐ$LUSRUWௐ3URGXFWVௐZDUUDQWVௐWKHௐSXUFKDVHUௐWKDWௐWKHௐSDUWVௐVROGௐE\ௐ DIWHUPDUNHWௐEHௐIUHHௐIURPௐGHIHFWVௐLQௐSURGXFWௐDQGௐZRUNPDQVKLSௐIRUௐWKHௐSHULRGௐ RIௐVL[ௐPRQWKVௐIURPௐWKHௐGHOLYHU\ௐRIௐWKHௐSURGXFWௐ7KLVௐ3DUWVௐ:DUUDQW\ௐGRHVௐQRWௐ LQFOXGHௐIUHLJKWௐODERUௐWUDYHOௐRUௐPDUNXSௐ,WௐLVௐDௐSDUWௐZDUUDQW\ௐRQO\ௐ 5HWXUQௐRIௐ'HIHFWLYHௐ3DUWV
,IௐSDUWVௐXVHGௐLQௐWKHௐUHSDLUௐRIௐDQௐDSSDUDWXVௐDUHௐUHTXLUHGௐWRௐEHௐUHWXUQHGௐWRௐ 3LHUFHௐ'HDOHUVௐZLOOௐUHFHLYHௐQRWLILFDWLRQௐ'HDOHUVௐKDYHௐXSௐWRௐௐGD\VௐWRௐ UHWXUQௐWKHௐGHIHFWLYHௐFRPSRQHQWௐRUௐWKHௐZDUUDQW\ௐFODLPௐZLOOௐEHௐUHMHFWHG 

 'HVFULEHௐDQ\ௐVHUYLFHௐFRQWUDFWௐRSWLRQVௐIRUௐWKHௐ
LWHPVௐLQFOXGHGௐLQௐ\RXUௐSURSRVDO
$XWKRUL]HGௐ3LHUFHௐGHDOHUVௐPD\ௐRIIHUௐVHUYLFHௐFRQWUDFWVௐIRUௐSUHYHQWDWLYHௐ PDLQWHQDQFHௐSXUSRVHV
1RௐVHUYLFHௐFRQWUDFWVௐDUHௐLQFOXGHGௐLQௐWKLVௐSURSRVDO


7DEOH
3D\PHQW7HUPVDQG)LQDQFLQJ2SWLRQV
/LQH
,WHP 4XHVWLRQ 5HVSRQVH

 'HVFULEHௐ\RXUௐSD\PHQWௐWHUPVௐDQGௐDFFHSWHGௐSD\PHQWௐ
PHWKRGV
$OOௐVDOHVௐRIௐ3LHUFHௐDSSDUDWXVௐDUHௐVROGௐWKURXJKௐWKHௐDXWKRUL]HGௐ3LHUFHௐ GHDOHUVௐ3D\PHQWௐWHUPVௐDUHௐ&DVKௐRQௐ'HOLYHU\ௐ
&2'
ௐRUௐSUHSD\PHQW
XQOHVVௐRWKHUZLVHௐDJUHHGௐXSRQௐE\ௐWKHௐ3LHUFHௐGHDOHU
2VKNRVKௐ$LUSRUWௐ3URGXFWV¶ௐVWDQGDUGௐSD\PHQWௐWHUPVௐDUHௐQHWௐௐGD\Vௐ DIWHUௐGHOLYHU\ௐRIௐYHKLFOHௐௐ$FFHSWHGௐSD\PHQWௐPHWKRGVௐLQFOXGHௐFKHFNௐ DQGௐZLUHௐWUDQVIHU


 'HVFULEHௐDQ\ௐOHDVLQJௐRUௐILQDQFLQJௐRSWLRQVௐDYDLODEOHௐIRUௐXVHௐ E\ௐHGXFDWLRQDOௐRUௐJRYHUQPHQWDOௐHQWLWLHV
7KHௐVDPHௐORJLFௐEHKLQGௐRXUௐFXVWRPௐFKDVVLVௐDSSOLHVௐWRௐRXUௐILQDQFLDOௐ

VHUYLFHV
ௐ7DLORUௐWKHௐSURGXFWௐWRௐWKHௐGHSDUWPHQWௐQRWௐWKHௐRWKHUௐZD\ௐ DURXQGௐ7KHௐ&RPSDQ\ௐRIIHUVௐWZRௐWRௐILIWHHQ\HDUௐPXQLFLSDOௐOHDVH ILQDQFLQJௐSURJUDPVௐWRௐLWVௐ)LUHௐ ௐ(PHUJHQF\ௐVHJPHQWௐFXVWRPHUVௐLQ WKHௐ86ௐWKURXJKௐWKH
3LHUFHௐ)LQDQFLDOௐ6ROXWLRQVௐSURJUDPௐSURYLGHGௐE\ௐ31&ௐ(TXLSPHQWௐ )LQDQFHௐ3URJUDPVௐLQFOXGHௐFRPSHWLWLYHௐOHDVHௐILQDQFLQJௐUDWHVௐ FUHDWLYHௐDQGௐIOH[LEOH
ILQDQFHௐDUUDQJHPHQWVௐDQGௐWKHௐHDVHௐRIௐRQHVWRSௐVKRSSLQJௐIRUௐ FXVWRPHUV¶ௐHTXLSPHQWௐDQGௐILQDQFLQJௐ7KHௐ&RPSDQ\ௐH[HFXWHVௐWKHௐ OHDVHௐILQDQFLQJ
WUDQVDFWLRQVௐWKURXJKௐDௐFREUDQGHGௐDUUDQJHPHQWௐZLWKௐDQௐLQGHSHQGHQWௐ WKLUGSDUW\ௐILQDQFHௐFRPSDQ\ௐ7KHௐ&RPSDQ\ௐW\SLFDOO\ௐSURYLGHVௐFUHGLWௐ VXSSRUWௐLQ
FRQQHFWLRQௐZLWKௐWKHVHௐILQDQFLQJௐDQGௐOHDVLQJௐDUUDQJHPHQWVௐ:LWKௐ LQGXVWU\OHDGLQJௐWD[H[HPSWௐUDWHVௐ]HURௐGRFXPHQWDWLRQௐIHHVௐIOH[LEOHௐ SD\PHQWௐSODQVௐDQGௐTXLFNௐDSSURYDOVௐWKDWௐFDQௐE\SDVVௐYRWHUௐ UHIHUHQGXPVௐZHௐPDNHௐLWௐHDV\ௐWRௐJHWௐEHKLQGௐWKHௐZKHHOௐRIௐ\RXUௐQHZௐ 3LHUFH
5HIHUௐWRௐௐ3LHUFHௐ)LQDQFLDOௐ6ROXWLRQVௐ7HVWLPRQLDOVSGIௐDQGௐௐ )LQDQFLDOB6ROXWLRQVSGIௐLQௐWKHௐ$GGLWLRQDOௐ'RFXPHQWVௐIROGHU 

 'HVFULEHௐDQ\ௐVWDQGDUGௐWUDQVDFWLRQௐGRFXPHQWVௐWKDWௐ\RXௐ SURSRVHௐWRௐXVHௐLQௐFRQQHFWLRQௐZLWKௐDQௐDZDUGHGௐFRQWUDFWௐ

RUGHUௐIRUPVௐWHUPVௐDQGௐFRQGLWLRQVௐVHUYLFHௐOHYHOௐ
DJUHHPHQWVௐHWF
ௐ8SORDGௐDௐVDPSOHௐRIௐHDFKௐ
DVௐ

DSSOLFDEOH
ௐLQௐWKHௐGRFXPHQWௐXSORDGௐVHFWLRQௐRIௐ\RXUௐ
UHVSRQVH
3LHUFHௐKDVௐDௐYDULDWLRQௐRIௐVWDQGDUGௐZDUUDQW\ௐGRFXPHQWVௐ6DPSOHௐ GRFXPHQWVௐDUHௐLQFOXGHGௐLQௐWKHௐZDUUDQW\ௐGRFXPHQWௐXSORDGVௐ 1RௐVWDQGDUGௐWUDQVDFWLRQௐGRFXPHQWVௐDUHௐEHLQJௐUHTXHVWHGௐWRௐXVHௐLQ FRQQHFWLRQௐZLWKௐDQௐDZDUGHGௐFRQWUDFWௐ
1RௐVHUYLFHௐFRQWUDFWVௐDUHௐLQFOXGHGௐLQௐWKLVௐSURSRVDOௐ$XWKRUL]HGௐ3LHUFHௐ GHDOHUVௐPD\ௐRIIHUௐVHUYLFHௐFRQWUDFWVௐIRUௐSUHYHQWDWLYHௐPDLQWHQDQFHௐ SXUSRVHV


 'Rௐ\RXௐDFFHSWௐWKHௐ3FDUGௐSURFXUHPHQWௐDQGௐSD\PHQWௐ
SURFHVV"ௐ,IௐVRௐLVௐWKHUHௐDQ\ௐDGGLWLRQDOௐFRVWௐWRௐ6RXUFHZHOOௐ SDUWLFLSDWLQJௐHQWLWLHVௐIRUௐXVLQJௐWKLVௐSURFHVV"
3LHUFHௐ$LUSRUWௐ3URGXFWVௐDQGௐWKHLUௐLQGHSHQGHQWௐGHDOHUVௐGRௐQRWௐILQGௐ WKDWௐ3FDUGௐSURFXUHPHQWௐDQGௐSD\PHQWௐIHDVLEOHௐGXHௐWRௐWKHௐVL]HௐDQGௐ EXLOGௐFRPSOH[LW\ௐRIௐRXUௐSURGXFWV


7DEOH
3ULFLQJDQG'HOLYHU\
Bid Number: RFP 113021 Vendor Name: Pierce Manufacturing 













 

EXHIBIT 1 602
3URYLGHGHWDLOHGSULFLQJLQIRUPDWLRQLQWKHTXHVWLRQVWKDWIROORZEHORZ.HHSLQPLQGWKDWUHDVRQDEOHSULFHDQGSURGXFWDGMXVWPHQWVFDQ EHPDGHGXULQJWKHWHUPRIDQDZDUGHG&RQWUDFWDVGHVFULEHGLQWKH5)3WKHWHPSODWH&RQWUDFWDQGWKH6RXUFHZHOO3ULFHDQG3URGXFW &KDQJH5HTXHVW)RUP
/LQH
,WHP 4XHVWLRQ 5HVSRQVH

 'HVFULEHௐ\RXUௐSULFLQJௐPRGHOௐ
HJௐOLQHLWHPௐGLVFRXQWVௐRUௐ
SURGXFWFDWHJRU\ௐGLVFRXQWV
ௐ3URYLGHௐGHWDLOHGௐSULFLQJௐGDWDௐ

LQFOXGLQJௐVWDQGDUGௐRUௐOLVWௐSULFLQJௐDQGௐWKHௐ6RXUFHZHOOௐ
GLVFRXQWHGௐSULFH
ௐRQௐDOOௐRIௐWKHௐLWHPVௐWKDWௐ\RXௐZDQWௐ
6RXUFHZHOOௐWRௐFRQVLGHUௐDVௐSDUWௐRIௐ\RXUௐ5)3ௐUHVSRQVHௐ,Iௐ DSSOLFDEOHௐSURYLGHௐDௐ6.8ௐIRUௐHDFKௐLWHPௐLQௐ\RXUௐSURSRVDOௐ 8SORDGௐ\RXUௐSULFLQJௐPDWHULDOVௐ
LIௐDSSOLFDEOH
ௐLQௐWKHௐ
GRFXPHQWௐXSORDGௐVHFWLRQௐRIௐ\RXUௐUHVSRQVH
&RPELQDWLRQௐRIௐOLQHௐLWHPௐDQGௐSHUFHQWDJHௐGLVFRXQWௐDUHௐSURYLGHGௐLQௐ DQௐDWWDFKHGௐ3')ௐGRFXPHQWௐLGHQWLILHGௐDVௐIROORZV
‡ௐ3URGXFWௐ&DWHJRU\
‡ௐ,GHQWLILFDWLRQௐ,'
‡ௐ3URGXFWௐ'HVFULSWLRQ
‡ௐ/LVWௐ3ULFH
‡ௐ3HUFHQWDJHௐRIIௐSHUௐSURGXFW
‡ௐ/LQHௐ,WHPௐ
&RQWUDFW
ௐ3ULFH
7KHௐ3HUFHQWDJHௐ'LVFRXQWௐLWHPVௐDUHௐDOVRௐDSSOLFDEOHௐWRௐWKHௐ XQSXEOLVKHGௐRSWLRQVௐDGGHGௐWRௐWKHௐSXEOLVKHGௐEDVHௐVSHFLILFDWLRQௐZLWKௐ DௐVWDQGDUGௐGLVFRXQWௐRIIௐRIௐ/LVWௐFRQWLQJHQWௐRQௐWKHௐSURGXFW 

 4XDQWLI\ௐWKHௐSULFLQJௐGLVFRXQWௐUHSUHVHQWHGௐE\ௐWKHௐSULFLQJௐ SURSRVDOௐLQௐWKLVௐUHVSRQVHௐ)RUௐH[DPSOHௐLIௐWKHௐSULFLQJௐLQௐ \RXUௐUHVSRQVHௐUHSUHVHQWVௐDௐSHUFHQWDJHௐGLVFRXQWௐIURPௐ
0653ௐRUௐOLVWௐVWDWHௐWKHௐSHUFHQWDJHௐRUௐSHUFHQWDJHௐUDQJH 7KHௐSULFLQJௐSUHVHQWHGௐLQௐWKLVௐSURSRVDOௐUHSUHVHQWVௐDௐௐGLVFRXQWௐ IURPௐ3LHUFH¶VௐOLVWௐSULFHௐIRUௐXQSXEOLVKHGௐRSWLRQV
$5))ௐSURGXFWVௐ
$LUSRUWௐ3URGXFWV
ௐUHSUHVHQWVௐDௐௐGLVFRXQWௐRIIௐRIௐ
OLVWௐSULFH


 'HVFULEHௐDQ\ௐTXDQWLW\ௐRUௐYROXPHௐGLVFRXQWVௐRUௐUHEDWHௐ SURJUDPVௐWKDWௐ\RXௐRIIHU
0XOWL8QLWௐ3XUFKDVHௐ'LVFRXQW
ௐௐ
$GGLWLRQDOௐGLVFRXQWVௐPD\ௐEHௐDYDLODEOHௐIRUௐLGHQWLFDOௐPXOWLXQLWௐ SXUFKDVHVௐௐ'LVFRXQWௐYDULHVௐGHSHQGHQWௐXSRQௐWKHௐQXPEHUௐRIௐLGHQWLFDOௐ XQLWVௐWKHௐFRQILJXUDWLRQௐRIௐWKHௐXQLWVௐDQGௐZLOOௐEHௐKDQGOHGௐRQௐDௐFDVH E\FDVHௐEDVLV
3UH3D\PHQWௐ'LVFRXQW
'LVFRXQWௐDPRXQWௐYDULHVௐGHSHQGHQWௐXSRQௐDSSDUDWXVௐSULFHௐGHOLYHU\ VFKHGXOHௐH[WHQWௐRIௐSUHSD\PHQWௐDQGௐDSSOLFDEOHௐUDWHௐௐ,IௐHOHFWHGௐ SD\PHQWௐIRUௐWKHௐHQWLUHௐFRQWUDFWௐDPRXQWௐLVௐGXHௐZLWKLQௐWKLUW\ௐ 
ௐGD\Vௐ
RIௐFRQWUDFWௐH[HFXWLRQௐ7KLVௐGHGXFWLRQௐLVௐLQௐDGGLWLRQௐWRௐDOOௐRWKHUௐ GLVFRXQWVௐOLVWHGௐDERYHௐ,IௐWKLVௐRSWLRQௐLVௐHOHFWHGௐILQDOௐSD\PHQWௐIRUௐ DQ\ௐFKDQJHVௐSURFHVVHGௐGXULQJௐPDQXIDFWXULQJௐLVௐGXHௐSULRUௐWRௐWKHௐXQLWௐ OHDYLQJௐWKHௐIDFWRU\ௐIRUௐGHOLYHU\
3D\PHQWௐ ௐSULFLQJௐRSWLRQV

&KDVVLVௐ3URJUHVVௐ3D\PHQWௐ'LVFRXQW
ௐ'LVFRXQWௐRIௐDSSUR[LPDWHO\ௐ
RIௐWKHௐFXVWRPௐFKDVVLVௐSULFHௐLVௐRIIHUHGௐLIௐDௐFKDVVLVௐSURJUHVVௐ SD\PHQWௐLVௐPDGHௐWKUHHௐ

ௐPRQWKVௐSULRUௐWRௐWKHௐ5)3ௐ
UHDG\ௐIRUௐSLFNௐ
XSௐIURPௐWKHௐIDFWRU\
ௐGDWHௐௐ([DPSOH
ௐௐ&KDVVLVௐSURJUHVVௐSD\PHQWௐLQௐ
WKHௐDPRXQWௐRIௐௐFRXOGௐHDUQௐDௐGLVFRXQWௐRIௐ

ௐௐ
7KLVௐGLVFRXQWௐLVௐQRWௐDYDLODEOHௐIRUௐ&RPPHUFLDOௐFKDVVLVௐSURGXFWV $HULDOௐ'HYLFHௐ3URJUHVVௐ3D\PHQWௐ'LVFRXQW
ௐ'LVFRXQWௐRIௐ
DSSUR[LPDWHO\ௐௐRIௐWKHௐDHULDOௐGHYLFHௐSULFHௐLVௐRIIHUHGௐLIௐDQௐDHULDOௐ GHYLFHௐSURJUHVVௐSD\PHQWௐLVௐPDGHௐWZRௐ

ௐPRQWKVௐSULRUௐWRௐWKHௐ5)3

UHDG\ௐIRUௐSLFNௐXSௐIURPௐWKHௐIDFWRU\
ௐGDWHௐௐ([DPSOH
ௐௐ$HULDOௐGHYLFHௐ
SURJUHVVௐSD\PHQWௐLQௐWKHௐDPRXQWௐRIௐௐFRXOGௐHDUQௐDௐ GLVFRXQWௐRIௐ





3URSRVHௐDௐPHWKRGௐRIௐIDFLOLWDWLQJௐ³VRXUFHG´ௐSURGXFWVௐRUௐ UHODWHGௐVHUYLFHVௐZKLFKௐPD\ௐEHௐUHIHUUHGௐWRௐDVௐ³RSHQௐ
PDUNHW´ௐLWHPVௐRUௐ³QRQVWDQGDUGௐRSWLRQV´ௐ)RUௐH[DPSOHௐ\RXௐ PD\ௐVXSSO\ௐVXFKௐLWHPVௐ³DWௐFRVW´ௐRUௐ³DWௐFRVWௐSOXVௐDௐ
SHUFHQWDJH´ௐRUௐ\RXௐPD\ௐVXSSO\ௐDௐTXRWHௐIRUௐHDFKௐVXFKௐ
UHTXHVW
6RXUFHGௐRUௐRSHQௐPDUNHWௐLWHPVௐPD\ௐEHௐSURYLGHGௐE\ௐWKHௐ3LHUFHௐ DXWKRUL]HGௐGHDOHUௐDQGௐZRXOGௐEHௐTXRWHGௐDWௐWLPHௐRIௐUHTXHVW 

Bid Number: RFP 113021 Vendor Name: Pierce Manufacturing 













 

EXHIBIT 1 603
 ,GHQWLI\ௐDQ\ௐHOHPHQWௐRIௐWKHௐWRWDOௐFRVWௐRIௐDFTXLVLWLRQௐWKDWௐLV 127ௐLQFOXGHGௐLQௐWKHௐSULFLQJௐVXEPLWWHGௐZLWKௐ\RXUௐUHVSRQVHௐ 7KLVௐLQFOXGHVௐDOOௐDGGLWLRQDOௐFKDUJHVௐDVVRFLDWHGௐZLWKௐDௐ SXUFKDVHௐWKDWௐDUHௐQRWௐGLUHFWO\ௐLGHQWLILHGௐDVௐIUHLJKWௐRUௐ VKLSSLQJௐFKDUJHVௐ)RUௐH[DPSOHௐOLVWௐFRVWVௐIRUௐLWHPVௐOLNHௐSUH GHOLYHU\ௐLQVSHFWLRQௐLQVWDOODWLRQௐVHWௐXSௐPDQGDWRU\ௐWUDLQLQJௐ RUௐLQLWLDOௐLQVSHFWLRQௐ,GHQWLI\ௐDQ\ௐSDUWLHVௐWKDWௐLPSRVHௐVXFKௐ FRVWVௐDQGௐWKHLUௐUHODWLRQVKLSௐWRௐWKHௐ3URSRVHU
3UH'HOLYHU\ௐ([SHQVHV
'HDOHUௐSURYLGHGௐRSWLRQVௐFDQௐEHௐDGGHGௐWRௐWKHௐDSSDUDWXVௐFRQWUDFWௐ XSRQௐUHTXHVWௐDQGௐZLOOௐEHௐKDQGOHGௐE\ௐWKHௐ3LHUFHௐDXWKRUL]HGௐGHDOHUௐௐ 'HDOHUௐSURYLGHGௐRSWLRQVௐFDQௐYDU\ௐGHSHQGLQJௐXSRQௐWKHௐFXVWRPHU¶Vௐ UHTXHVWௐDQGௐFDQௐLQFOXGHௐEXWௐDUHௐQRWௐOLPLWHGௐWRௐWKHௐLWHPVௐOLVWHG EHORZௐௐ3ULFLQJௐZLOOௐEHௐSURYLGHGௐWRௐHDFKௐFXVWRPHUௐXSRQௐUHTXHVWௐDQGௐ YDULHVௐE\ௐGHDOHUVKLSௐDQGௐFXVWRPHUௐORFDWLRQ
ௐௐௐௐ)DFWRU\ௐLQVSHFWLRQௐWULSV
ௐௐௐௐ:HHNO\ௐFRQVWUXFWLRQௐSKRWRௐSURJUHVVௐUHSRUWVௐ
ௐௐௐௐ2ULHQWDWLRQௐ'9'ௐVSHFLILFௐWRௐ\RXUௐDSSDUDWXV
ௐௐௐௐ/RRVHௐ(TXLSPHQW
ௐௐௐௐ(QJLQHௐDQGௐRUௐWUDQVPLVVLRQௐGLDJQRVWLFௐVRIWZDUH
ௐௐௐௐ/RRVHௐHTXLSPHQWௐ
RSHQௐPDUNHWௐLWHPV
ௐVXFKௐDVௐEXWௐQRWௐOLPLWHG
WRௐPRQLWRUVௐKRVHௐLQWHUFRPௐV\VWHPௐUDGLRௐHTXLSPHQWௐDQGௐUHVFXH WRROVௐDQGௐHTXLSPHQW
ௐௐௐௐ3UHGHOLYHU\ௐVHUYLFHௐFRQVLVWLQJௐRIௐEDVLFௐIOXLGVௐDQGௐILOWHUV ௐௐௐௐ&XVWRPௐIDEULFDWLRQௐIRUௐWRROௐPRXQWLQJௐDQGௐFRPPXQLFDWLRQௐ HTXLSPHQWௐ
ௐௐௐௐ2WKHUௐLWHPVௐDVௐUHTXHVWHGௐE\ௐFXVWRPHUௐDQGௐGHHPHGௐVRXUFHGௐ RUௐRSHQௐPDUNHW
ௐௐௐௐ'HOLYHU\ௐ
ௐௐௐௐ6DOHVௐDQGௐRWKHUௐWD[HVௐOLFHQVHௐKDQGOLQJௐRUௐWLWOHௐIHHVௐDUHௐDOVRௐ QRWௐLQFOXGHG


 ,IௐIUHLJKWௐGHOLYHU\ௐRUௐVKLSSLQJௐLVௐDQௐDGGLWLRQDOௐFRVWௐWRௐWKHௐ 6RXUFHZHOOௐSDUWLFLSDWLQJௐHQWLW\ௐGHVFULEHௐLQௐGHWDLOௐWKHௐ FRPSOHWHௐIUHLJKWௐVKLSSLQJௐDQGௐGHOLYHU\ௐSURJUDP
7UDQVSRUWDWLRQௐ([SHQVHV
3ULFHVௐTXRWHGௐLQௐ5)3ௐௐDUHௐ)2%ௐ0DQXIDFWXUHU¶VௐIDFLOLW\ௐௐ 7UDQVSRUWDWLRQௐRIௐWKHௐDSSDUDWXVௐIURPௐWKHௐIDFWRU\ௐWRௐWKHௐFXVWRPHU¶Vௐ IDFLOLW\ௐFDQௐEHௐDGGHGௐWRௐWKHௐFRQWUDFWௐௐ,QௐPRVWௐFDVHVௐWKHௐDSSDUDWXVௐ LVௐGHOLYHUHGௐWRௐWKHௐ3LHUFHௐDXWKRUL]HGௐGHDOHUௐIDFLOLW\ௐLQௐWKHௐDUHDௐIRUௐDௐ 3UH'HOLYHU\ௐLQVSHFWLRQௐDQGௐWKHௐLQVWDOODWLRQௐRIௐDQ\ௐGHDOHUௐSURYLGHGௐ RSWLRQVௐLIௐDSSOLFDEOHௐௐ,IௐWKHUHௐLVௐQRWௐDௐ3LHUFHௐDXWKRUL]HGௐGHDOHUௐ IDFLOLW\ௐQHDUௐWKHௐFXVWRPHUௐORFDWLRQௐWKHௐDSSDUDWXVௐPD\ௐEHௐGHOLYHUHGௐ GLUHFWO\ௐWRௐWKHௐIDFLOLW\ௐௐ7KHௐFRVWௐIRUௐWKLVௐWUDQVSRUWDWLRQௐYDULHVௐ GHSHQGHQWௐXSRQௐWKHௐW\SHௐRIௐDSSDUDWXVௐDQGௐWKHௐSUR[LPLW\ௐRIௐ\RXUௐ IDFLOLW\ௐWRௐWKHௐORFDWLRQௐRIௐWKHௐPDQXIDFWXUHU¶VௐIDFLOLW\ௐௐ'HOLYHU\ௐLVௐ FRQGXFWHGௐLQௐDFFRUGDQFHௐZLWKௐ'27ௐUHJXODWLRQVௐௐ'HOLYHU\ௐFKDUJHV FDQௐYDU\ௐEDVHGௐRQௐWKHௐORJLVWLFௐRUௐVKLSSLQJௐORFDWLRQௐDQGௐ UHTXLUHPHQWVௐIRUௐH[DPSOHௐPRUHௐLIௐIODWEHGௐEDUJHௐRUௐFRQWDLQHUௐVKLSௐ WUDQVSRUWௐLVௐUHTXLUHG


 6SHFLILFDOO\ௐGHVFULEHௐIUHLJKWௐVKLSSLQJௐDQGௐGHOLYHU\ௐWHUPVௐRUௐ SURJUDPVௐDYDLODEOHௐIRUௐ$ODVNDௐ+DZDLLௐ&DQDGDௐRUௐDQ\ௐ
RIIVKRUHௐGHOLYHU\
6KLSSLQJௐDQGௐ'HOLYHU\ௐSURJUDPVௐIRUௐDUHDVௐVXFKௐDVௐ$ODVNDௐ+DZDLLௐ RUௐDQ\ௐRIIVKRUHௐGHOLYHU\ௐUHTXLUHVௐFRRUGLQDWLRQௐRIௐGLIIHUHQWௐWUDQVLWௐ PHWKRGVௐ0RVWௐRIWHQௐWKHௐDSSDUDWXVௐLVௐIODWEHGௐWRௐWKHௐSRUWௐGHVWLQDWLRQௐ SUHSDUHGௐIRUௐRFHDQௐWUDQVLWௐDQGௐWUDYHOௐWRௐILQDOௐGHVWLQDWLRQௐ UROORQUROOௐ
RIIௐYHVVHOௐLVௐSUHIHUUHG
ௐ7KLVௐXQLTXHௐVKLSSLQJௐDQGௐGHOLYHU\ௐ
UHTXLUHPHQWVௐDUHௐSULFHGௐRQௐDௐFDVHE\FDVHௐEDVLVௐDVௐUHTXLUHG 6KLSSLQJௐZLWKLQௐWKHௐFRQWLJXRXVௐ86ௐVWDWHVௐDQGௐ&DQDGDௐVKLSSLQJௐLVௐ FDOFXODWHGௐXVLQJௐQXPHURXVௐIDFWRUVௐLQFOXGLQJௐEXWௐQRWௐOLPLWHGௐWRௐWKHௐ W\SHௐRIௐDSSDUDWXVௐZKLFKௐLPSDFWVௐSHUPLWVௐDVௐZHOOௐDVௐWKHௐGLVWDQFHௐWRௐ GHVWLQDWLRQௐ6KLSSLQJௐH[SHQVHVௐDUHௐQRWௐLQFOXGHGௐLQௐWKHௐEDVHௐ VSHFLILFDWLRQVௐFRVW


 'HVFULEHௐDQ\ௐXQLTXHௐGLVWULEXWLRQௐDQGRUௐGHOLYHU\ௐPHWKRGVௐRUௐ RSWLRQVௐRIIHUHGௐLQௐ\RXUௐSURSRVDO
)RUௐ$5))ௐYHKLFOHVௐGXHௐWRௐVL]HௐDQGௐZHLJKWௐUHVWULFWLRQVௐDOOௐWUXFNVௐZLOOௐ EHௐWUDQVSRUWHGௐYLDௐORZER\ௐRUௐIODWEHGௐௐ$OOௐUHTXLUHGௐOLFHQVHVௐDQGௐ SHUPLWVௐZLOOௐEHௐREWDLQHGௐSULRUௐWRௐVKLSPHQW


7DEOH
3ULFLQJ2IIHUHG
/LQH
,WHP 7KH3ULFLQJ2IIHUHGLQWKLV3URSRVDOLV

&RPPHQWV
 EWKHVDPHDVWKH3URSRVHUW\SLFDOO\RIIHUVWR*32VFRRSHUDWLYHSURFXUHPHQWRUJDQL]DWLRQVRUVWDWHSXUFKDVLQJ GHSDUWPHQWV
3LHUFHௐZLOOௐQRWௐIDYRUௐRQHௐ
*32ௐRYHUௐDQRWKHUௐ7KHUHIRUH
SULFLQJௐPRGHOௐLVௐFRQVLVWHQWௐ
DFURVVௐDOO
Bid Number: RFP 113021 Vendor Name: Pierce Manufacturing 













 

EXHIBIT 1 604
7DEOH
$XGLWDQG$GPLQLVWUDWLYH)HH
/LQH
,WHP 4XHVWLRQ 5HVSRQVH

 6SHFLILFDOO\ௐGHVFULEHௐDQ\ௐVHOIDXGLWௐSURFHVVௐRUௐSURJUDPௐWKDWௐ\RXௐ SODQௐWRௐHPSOR\ௐWRௐYHULI\ௐFRPSOLDQFHௐZLWKௐ\RXUௐSURSRVHGௐ&RQWUDFW ZLWKௐ6RXUFHZHOOௐ7KLVௐSURFHVVௐLQFOXGHVௐHQVXULQJௐWKDWௐ6RXUFHZHOO SDUWLFLSDWLQJௐHQWLWLHVௐREWDLQௐWKHௐSURSHUௐSULFLQJௐWKDWௐWKHௐ9HQGRUௐ UHSRUWVௐDOOௐVDOHVௐXQGHUௐWKHௐ&RQWUDFWௐHDFKௐTXDUWHUௐDQGௐWKDWௐWKH 9HQGRUௐUHPLWVௐWKHௐSURSHUௐDGPLQLVWUDWLYHௐIHHௐWRௐ6RXUFHZHOOௐ3URYLGHௐ VXIILFLHQWௐGHWDLOௐWRௐVXSSRUWௐ\RXUௐDELOLW\ௐWRௐUHSRUWௐTXDUWHUO\ௐVDOHVௐWRௐ 6RXUFHZHOOௐDVௐGHVFULEHGௐLQௐWKHௐ&RQWUDFWௐWHPSODWH
3LHUFHௐWDNHVௐSULGHௐLQௐXSKROGLQJௐWKHௐLQWHJULW\ௐRIௐWKHௐSURJUDPVௐ DQGௐFRQWUDFWVௐZHௐSDUWLFLSDWHௐLQௐ
6\VWHPௐVRIWZDUHௐFKDQJHVௐKDYHௐEHHQௐEXLOWௐWRௐIDFLOLWDWHௐWKHௐ LQIRUPDWLRQௐJDWKHUHGௐWKURXJKRXWௐDQ\ௐRIௐRXUௐSURJUDPVௐWRௐ HIILFLHQWO\ௐUXQௐUHSRUWVௐRQௐGHPDQGௐ7KHVHௐUHSRUWVௐDUHௐUXQௐDWௐDௐ PLQLPXPௐPRQWKO\ௐIRUௐLQWHUQDOௐDXGLWௐSXUSRVHVௐDQGௐTXDUWHUO\ௐIRUௐ FRQWUDFWௐUHTXLUHPHQWV
$OOௐEDVHௐVSHFLILFDWLRQVௐDQGௐDGGLWLRQDOௐXSJUDGHௐRSWLRQVௐKDYHௐ EHHQௐFUHDWHGௐLQௐRXUௐFXVWRPL]HGௐWUXFNௐFRQILJXUDWRUௐWRROௐ 38/6(ௐVRௐWKDWௐDௐ'HDOHUௐFDQௐFRS\ௐWKDWௐEDVHௐVSHFLILFDWLRQௐWRௐ FRQILUPௐOLQHLWHPௐSULFLQJௐ$Q\ௐFKDQJHVௐPDGHௐWRௐWKHௐEDVHௐ VSHFLILFDWLRQௐLVௐWKHQௐFRQWUROOHGௐDQGௐFDSWXUHGௐLQௐDௐ&KDQJHௐ 5HSRUWௐWKDWௐFDQௐEHௐYDOLGDWHGௐWRௐKRQRUௐWKHௐ3HUFHQWDJHௐ
'LVFRXQWௐRQௐRSWLRQVௐDGGHG
7KHௐSURFHVVௐ
VHHௐDGGLWLRQDOௐGRFXPHQWV
ௐRXWOLQHௐVKRZVௐWKDWௐ
3LHUFHௐKDVௐDௐFORVHGORRSௐSURFHVVௐWKDWௐSURYLGHௐFKHFNVௐDQGௐ EDODQFHVௐIRUௐDOOௐLQYROYHG
2XUௐUHSRUWLQJௐFDSDELOLWLHVௐIRUௐRWKHUௐFRQWUDFWVௐKDYHௐEHHQௐ QRWHGௐWRௐEHௐWLPHO\ௐWKRURXJKௐDQGௐDFFXUDWHௐ7KHௐYROXPHௐRIௐ VDOHVௐXQGHUௐRXUௐFRQVRUWLXPௐSURJUDPVௐUHTXLUHVௐ3LHUFHௐWRௐ KDYHௐDௐZHOOGHILQHGௐDQGௐHIILFLHQWௐSURFHVV
$ZDUGHGௐFRQWUDFWVௐDUHௐDXGLWHGௐRQௐSURGXFWௐFRVWௐODERUௐ
HIILFLHQFLHVௐSURGXFWௐPDUJLQௐDQGௐFXVWRPHUௐVDWLVIDFWLRQ 5HIHUௐWRௐ7DEOHௐௐ4XHVWLRQௐௐ$XGLWௐDQGௐ$GPLQLVWUDWLYHௐ )HHSGIௐLQௐ3ULFLQJௐIROGHU


 ,Iௐ\RXௐDUHௐDZDUGHGௐDௐFRQWUDFWௐSURYLGHௐDௐIHZௐH[DPSOHVௐRIௐLQWHUQDOௐ PHWULFVௐWKDWௐZLOOௐEHௐWUDFNHGௐWRௐPHDVXUHௐZKHWKHUௐ\RXௐDUHௐKDYLQJௐ VXFFHVVௐZLWKௐWKHௐFRQWUDFW
2QௐDௐPRQWKO\ௐEDVLVௐ3LHUFHௐZLOOௐSURYLGHௐWKHௐSHUFHQWDJHௐRIௐ 6RXUFHZHOOௐRUGHUVௐWRௐHDFKௐDXWKRUL]HGௐGHDOHUௐLQௐZKLFKௐWKH\ௐ FDQௐFRPSDUHௐWRௐWKHௐSULRUௐ\HDUௐWKLVௐLVௐSURYLGHGௐLQௐWKHLUௐ PRQWKO\ௐGDVKERDUGV


 ,GHQWLI\ௐDௐSURSRVHGௐDGPLQLVWUDWLYHௐIHHௐWKDWௐ\RXௐZLOOௐSD\ௐWRௐ 6RXUFHZHOOௐIRUௐIDFLOLWDWLQJௐPDQDJLQJௐDQGௐSURPRWLQJௐWKHௐ6RXUFHZHOOௐ &RQWUDFWௐLQௐWKHௐHYHQWௐWKDWௐ\RXௐDUHௐDZDUGHGௐDௐ&RQWUDFWௐௐ7KLVௐIHHௐ LVௐW\SLFDOO\ௐFDOFXODWHGௐDVௐDௐSHUFHQWDJHௐRIௐ9HQGRU¶VௐVDOHVௐXQGHUௐWKHௐ &RQWUDFWௐRUௐDVௐDௐSHUXQLWௐIHH
ௐLWௐLVௐQRWௐDௐOLQHLWHPௐDGGLWLRQௐWRௐWKHௐ
0HPEHU¶VௐFRVWௐRIௐJRRGVௐ
6HHௐWKHௐ5)3ௐDQGௐWHPSODWHௐ&RQWUDFWௐIRUௐ
DGGLWLRQDOௐGHWDLOV

7KHௐ$GPLQLVWUDWLYHௐ)HHௐWKDWௐ3LHUFHௐZLOOௐSD\ௐWRௐ6RXUFHZHOOௐIRUௐ WKLVௐSURSRVHGௐFRQWUDFWௐLVௐDOLJQHGௐZLWKௐWKHௐRWKHUௐFRQWUDFWVௐ DZDUGHGௐWRௐ3LHUFHௐWRௐFUHDWHௐDOLJQPHQWௐDQGௐFRQVLVWHQF\ௐ7KDWௐ IHHௐZLOOௐEHௐDௐIODWௐௐ86'ௐSHUௐFXVWRPHUௐSXUFKDVHௐ
RUGHUௐRUௐVHSDUDWHௐFRQWUDFW


Bid Number: RFP 113021 Vendor Name: Pierce Manufacturing 













 

EXHIBIT 1 605
7DEOH$
'HSWKDQG%UHDGWKRI2IIHUHG(TXLSPHQW3URGXFWVDQG6HUYLFHV /LQH
,WHP 4XHVWLRQ 5HVSRQVH

 3URYLGHௐDௐGHWDLOHGௐGHVFULSWLRQௐRIௐWKHௐ
HTXLSPHQWௐSURGXFWVௐDQGௐVHUYLFHVௐWKDWௐ\RXௐ
DUHௐRIIHULQJௐLQௐ\RXUௐSURSRVDO
3LHUFHௐLVௐRIIHULQJௐDQௐDUUD\ௐRIௐILUHௐDSSDUDWXVௐWRௐPHHWௐWKHௐFXVWRPHU¶VௐQHHGVௐDFURVVௐ WKHௐ86ௐDQGௐ&DQDGDௐLQFOXGLQJௐ+DZDLLௐDQGௐ$ODVND
$XWKRUL]HGௐ3LHUFHௐGHDOHUVௐPD\ௐRIIHUௐVHUYLFHௐFRQWUDFWVௐIRUௐSUHYHQWDWLYHௐPDLQWHQDQFHௐ SXUSRVHVௐௐ2XUௐSURGXFWௐSRUWIROLRௐLQFOXGHVௐWKHௐLQGXVWU\ௐVWDQGDUGௐFDWHJRULHV ௐ&XVWRPௐ
DQGௐ&RPPHUFLDOௐ3XPSHUௐSURGXFWVௐ$HULDOௐSURGXFWVௐ&RPPDQGௐ$5))ௐ5HVFXHௐ SURGXFWVௐ7DQNHUௐSURGXFWVௐDQGௐ6SHFLDOW\ௐYHKLFOHV
&86720ௐ$1'ௐ&200(5&,$/ௐ3803(5ௐ352'8&76
3XPSHUௐSURGXFWVௐLQFOXGHௐFRPPHUFLDOௐDQGௐFXVWRPௐFKDVVLVௐZLWKௐYDU\LQJௐERG\ௐVL]HVௐ SXPSௐUDWHVௐZDWHUௐWDQNௐFDSDFLW\ௐDQGௐSXPSௐPRGXOHௐVW\OHௐ $(5,$/ௐ352'8&76
$HULDOௐSURGXFWVௐLQFOXGHௐODGGHUVௐSODWIRUPVௐDQGௐWLOOHUVௐ7KHVHௐSURYLGHௐODGGHUௐOHQJWKVௐ UDQJLQJௐIURPௐ¶ௐ±ௐ¶ௐ6HOHFWLRQVௐZLOOௐLQFOXGHௐYDULRXVௐD[OHௐFRQILJXUDWLRQVௐSXPSLQJௐ UDWHVௐODGGHUௐVW\OHVௐDQGௐPDWHULDO
(0(5*(1&<ௐ5(63216(ௐ9(+,&/(6ௐௐௐ'HVLJQHGௐWRௐVXSSRUWௐWKHௐGHPDQGVௐRIௐ HPHUJHQF\ௐUHVSRQVHௐ0DQ\ௐPRGHOVௐIDOOௐXQGHUௐWKLVௐFDWHJRU\ௐVXFKௐDVௐODUJHௐPRELOHௐ FRPPDQGௐPLGVL]HௐFRPPDQGௐYHKLFOHௐVPDOOௐPRELOHௐFRPPDQGௐDQGௐFUXௐPRELOHௐ FRPPDQGௐYHKLFOHௐ
5(6&8(ௐ352'8&76
5HVFXHௐSURGXFWVௐZLOOௐLQFOXGHௐFRPPHUFLDOௐDQGௐFXVWRPௐFKDVVLVௐRIIHULQJVௐDORQJௐZLWKௐDௐ ZDONLQௐRUௐQRQZDONLQௐVW\OHௐ
7KHௐFRQILJXUDWLRQௐFDSDELOLWLHVௐYDU\ௐEXWௐLQFOXGHVௐFDSDFLW\ௐWRௐLQWHJUDWHௐFRPSOH[ௐ$ௐ9ௐ QHWZRUNௐDQGௐUDGLRௐV\VWHPVௐDLUௐWRROௐV\VWHPVௐEUHDWKLQJௐDLUௐV\VWHPVௐZLWKௐ FRPSUHVVRUVௐK\GUDXOLFௐUHVFXHௐWRROௐV\VWHPVௐDQGௐZLQFKLQJௐFDSDELOLWLHVௐFUHZௐVHDWLQJௐ ZLWKௐVWRUDJHௐDQGௐFXVWRPௐIDEULFDWHGௐVKHOYHVௐDQGௐWUD\V
7$1.(5ௐ352'8&7
7DQNHUௐSURGXFWVௐRIIHUௐDௐGXDOௐUROHௐRIௐZDWHUௐWUDQVSRUWௐDQGௐRQWKHVSRWௐILUHILJKWLQJௐ 3LHUFHௐRIIHUVௐ(OOLSWLFDOௐWDQNHUVௐ7DQNHU3XPSHUௐPRGHOVௐ'U\ௐVLGHௐDQGௐ:HWௐVLGHௐVW\OHVௐ WRௐFKRRVHௐIURPௐ(DFKௐWDQNHUௐLVௐFXVWRPௐGHVLJQHGௐWRௐDFFRPPRGDWHௐWKHௐILUHௐ GHSDUWPHQW¶VௐZDWHUௐIRDPௐDQGௐHTXLSPHQWௐVWRUDJHௐQHHGVௐ3LHUFHௐ7DQNHUVௐIHDWXUHௐ VROLGௐOLJKWZHLJKWௐFRUURVLRQIUHHௐSRO\SURS\OHQHௐWDQNVௐ7KHௐWDQNVௐDUHௐIRUPILWWHGௐ VSHFLILFDOO\ௐIRUௐ3LHUFHௐYHKLFOHVௐDQGௐFRPHௐZLWKௐDௐOLIHWLPHௐZDUUDQW\ 63(&,$/7<ௐ9(+,&/(6
6SHFLDOW\ௐYHKLFOHVௐDUHௐWKRVHௐXQLTXHௐYHKLFOHVௐWKDWௐKDYHௐDௐSXUSRVHௐLQௐZKLFKௐMXVWௐRQHௐ PD\ௐEHௐQHHGHGௐ6SHFLDOW\ௐYHKLFOHVௐPD\ௐUDQJHௐIURPௐDௐPLQLௐSXPSHUௐWRௐDௐ:LOGODQGௐ 7\SHௐ,,,ௐYHKLFOHௐRUௐDௐ,QGXVWULDOௐ)LUHௐ)LJKWLQJௐ9HKLFOHௐ 0D[L0HWDOௐ3DUWQHUVKLSௐ
0$;,0(7$/ௐ352'8&76ௐௐDUHௐGLVWULEXWHGௐLQௐWKHௐ86$ௐWKURXJKௐ3,(5&(ௐ 0$18)$&785,1*ௐDQGௐWKHௐGHDOHUௐQHWZRUNௐXQGHUௐWKHௐEUDQGௐQDPHௐ³&217(1'(5ௐ%<ௐ 0$;,0(7$/ௐ7KHௐ³&RQWHQGHUௐE\ௐ0$;,0(7$/´ௐSURGXFWௐOLQHௐZLOOௐEHௐVXEPLWWHGௐE\ௐ 0$;,0(7$/ௐIRUௐFRQVLGHUDWLRQௐ
$LUFUDIWௐ5HVFXHௐDQGௐ)LUHௐ)LJKWLQJௐ9HKLFOHVௐ
$5))
ௐ±ௐ$LUSRUWௐ3URGXFWVௐRIIHUVௐWKHௐ
2VKNRVKௐ6WULNHUௐ[ௐ[ௐDQGௐ[ௐDORQJௐZLWKௐWKHௐ6WLQJHUௐ4ௐ5,9ௐ 5DSLGௐ,QWHUYHQWLRQௐ
9HKLFOH
ௐௐ7KHௐ$5))ௐYHKLFOHௐZLOOௐEHௐHTXLSSHGௐWRௐPHHWௐ1)3$ௐௐUHTXLUHPHQWVௐZLWKௐ RSWLRQDOௐHTXLSPHQWௐDQGௐFRQILJXUDWLRQVௐWRௐPHHWௐLQGLYLGXDOௐDLUSRUWௐQHHGV 


:LWKLQௐWKLVௐ5)3ௐFDWHJRU\ௐWKHUHௐPD\ௐEHௐ
VXEFDWHJRULHVௐRIௐVROXWLRQVௐ/LVWௐVXEFDWHJRU\ௐ
WLWOHVௐWKDWௐEHVWௐGHVFULEHௐ\RXUௐSURGXFWVௐDQGௐ
VHUYLFHV
3OHDVHௐVHHௐTXHVWLRQௐௐVXEFDWHJRULHVௐDVௐWKH\ௐDUHௐGHVFULEHGௐ7KHUHௐLVௐDOVRௐ OLWHUDWXUHௐLQFOXGHGௐWRௐSURYLGHௐWKHௐEUHDWKௐRIௐSURGXFWVௐZHௐVHOOௐVHUYLFHௐDQGௐVXSSRUWௐ 1RௐVHUYLFHௐFRQWUDFWVௐDUHௐLQFOXGHGௐLQௐWKLVௐSURSRVDOௐ([DPSOHௐEHORZௐRIௐVXEFDWHJRULHVௐ &DWHJRU\ௐௐ(PHUJHQF\ௐ5HVSRQVHௐ9HKLFOHVௐௐ$5))ௐ$HULDOௐ3XPSHUௐ5HVFXHௐ7DQNHUௐ 6SHFLDOW\ௐ
6XEFDWHJRU\ௐௐ/DGGHUௐ3XPSHUVௐ:DONௐ,Qௐ3XPSHUௐ7DQNHUௐ:LOGODQGௐ3ODWIRUPVௐ 5HVFXHௐ3XPSHUௐ1RQௐ:DON,Qௐௐ'U\VLGHௐ7DQNHUௐ0LQL3XPSHUௐ&RPPDQG 

Bid Number: RFP 113021 Vendor Name: Pierce Manufacturing 













 

EXHIBIT 1 606
7DEOH%
'HSWKDQG%UHDGWKRI2IIHUHG(TXLSPHQW3URGXFWVDQG6HUYLFHV ,QGLFDWHEHORZLIWKHOLVWHGW\SHVRUFODVVHVRIHTXLSPHQWSURGXFWVDQGVHUYLFHVDUHRIIHUHGZLWKLQ\RXUSURSRVDO3URYLGHDGGLWLRQDO FRPPHQWVLQWKHWH[WER[SURYLGHGDVQHFHVVDU\
/LQH,WHP &DWHJRU\RU7\SH 2IIHUHG
&RPPHQWV
 )LUHILJKWLQJௐDSSDUDWXVௐDQGௐVHUYLFHௐYHKLFOHVௐRIௐDOOௐ W\SHVௐVXFKௐDV
ௐSXPSHUHQJLQHௐLQLWLDOௐDWWDFNௐ
PRELOHௐZDWHUௐVXSSO\ௐDHULDOௐTXLQWௐVSHFLDOௐVHUYLFHௐ
PRELOHௐIRDPௐFRPPDQGௐDQGௐFRPPXQLFDWLRQVௐDQGௐ
SXUSRVHEXLOWௐILUHILJKWLQJௐRUௐUHVFXHௐWUDLOHUV
<HV
1R
)URQWOLQHௐOHDGVௐVHUYLFHௐRQௐௐFRPPDQGௐ
DQGௐFRPPXQLFDWLRQV


 :LOGODQGௐILUHௐDSSDUDWXVௐRIௐDOOௐW\SHVௐVXFKௐDV
ௐILUHௐ
VXSSUHVVLRQௐHTXLSPHQWௐPRELOHௐZDWHUௐVXSSO\ௐDQGௐ
FUHZௐFDUULHUV
<HV
1R
1$


 $LUFUDIWௐUHVFXHௐDQGௐILUHILJKWLQJௐYHKLFOHV <HV
1R
2VKNRVKௐ$LUSRUWௐ3URGXFWV 

 3XUSRVHEXLOWௐFKDVVLVௐDQGௐYHKLFOHௐFRPSRQHQWVௐIRUௐ
ILUHILJKWLQJௐDSSDUDWXVௐDQGௐILUHௐVHUYLFHௐYHKLFOHV
<HV
1R
3LHUFHௐKDVௐDௐYDULHW\ௐRIௐFXVWRPௐEXLOWௐ
FKDVVLVௐWKDWௐ\RXௐZLOOௐILQGௐZLWKLQௐWKHௐ

GRFXPHQWV


 (TXLSPHQWௐRSWLRQVௐDFFHVVRULHVௐDQGௐVXSSOLHVௐ
FRPSOHPHQWDU\ௐRUௐLQFLGHQWDOௐWRௐWKHௐSXUFKDVHௐRIௐDௐ
WXUQNH\ௐRUௐFRPSOHWHௐXQLWௐRIௐWKHௐW\SHVௐGHVFULEHGௐLQௐ
/LQHVௐௐDERYH
<HV
1R
&DQௐEHௐRSHQௐVRXUFHௐ2IIHULQJௐLVௐRQO\ௐ
LQௐFRQMXQFWLRQௐZLWKௐDௐQHZௐRUGHU
 6HUYLFHVௐUHODWHGௐWRௐWKHௐRIIHULQJௐRIௐWKHௐVROXWLRQVௐ
GHVFULEHGௐLQௐ/LQHVௐௐLQFOXGLQJௐLQVWDOODWLRQௐ
FXVWRPL]DWLRQௐUHPRXQWௐUHIXUELVKPHQWௐLQVSHFWLRQௐ
UHSDLUௐPDLQWHQDQFHௐWUDLQLQJௐDQGௐVXSSRUW
<HV
1R
:HௐDUHௐUHTXLUHGௐWRௐSURYLGHௐWUDLQLQJௐ
RIௐRXUௐYHKLFOHௐSHUௐFRPSOLDQFHௐZLWKௐ
1)3$ௐ:HௐGRௐSURYLGHௐRSWLRQVௐZLWKLQௐ
RXUௐSURSRVDOVௐIRUௐWKLVௐDQGௐH[WHQGHGௐ
GXUDWLRQVௐWKDWௐKDYHௐDGGHGௐFRVWௐ
DVVRFLDWHG


Bid Number: RFP 113021 Vendor Name: Pierce Manufacturing 













 

EXHIBIT 1 607
7DEOH
,QGXVWU\6SHFLILF4XHVWLRQV
/LQH
,WHP 4XHVWLRQ 5HVSRQVH

 'HVFULEHௐDYDLODEOHௐVHUYLFHௐDQGௐUHSDLUௐ
RSWLRQVௐIRUௐWKHௐHTXLSPHQWௐDQGௐSURGXFWVௐ
RIIHUHGௐLQௐ\RXUௐSURSRVDO
3LHUFHௐ0DVWHUௐ7HFKQLFLDQௐ3URJUDPௐ
7KHௐ3LHUFHௐ0DVWHUௐ7HFKQLFLDQௐ3URJUDPௐLVௐIRFXVHGௐRQௐUHFRJQL]LQJௐVHUYLFHௐWHFKQLFLDQVௐ WKURXJKRXWௐWKHௐGHDOHUௐQHWZRUNௐIRUௐWKHLUௐNQRZOHGJHௐDQGௐDELOLW\ௐWRௐSURYLGHௐH[SHUWௐ VHUYLFHௐRQௐ3LHUFHௐDSSDUDWXVௐ:LWKௐWKLVௐWLHUHGௐOHYHOௐSURJUDPௐDௐWHFKQLFLDQௐFDQௐZRUNௐ WKHLUௐZD\ௐXSௐIURPௐKDYLQJௐRQHௐFHUWLILFDWLRQௐWRௐWKHௐOHYHOௐRIௐ0DVWHUௐ7HFKQLFLDQௐ$FWLYHௐ SDUWLFLSDWLRQௐLQௐWKHௐ$6(ௐ ௐ(97ௐSURJUDPVௐLVௐHQFRXUDJHGௐ$ௐ3LHUFHௐ0DVWHUௐ 7HFKQLFLDQௐPXVWௐVXFFHVVIXOO\ௐFRPSOHWHௐWKHௐGHILQHGௐFRUHௐFODVVHVௐGHGLFDWHGௐWRௐ H[FOXVLYHௐ3LHUFHௐSURGXFWVௐ$ௐFXPXODWLYHௐILQDOௐH[DPௐLVௐWDNHQௐXSRQௐFRPSOHWLRQௐRIௐWKHௐ FRUHௐFODVVHVௐWRௐREWDLQௐDௐ3LHUFHௐ0DVWHUௐ7HFKQLFLDQௐVWDWXVௐ3LHUFHௐKDVௐRYHUௐDௐௐ 0DVWHUௐ7HFKQLFLDQVௐFHUWLILHG


 'HVFULEHௐDYDLODEOHௐUHPRXQWௐRUௐUHIXUELVKLQJௐ
VHUYLFHVௐLQFOXGHGௐZLWKLQௐ\RXUௐSURSRVDOௐWKHௐ
SULFLQJௐPHWKRGௐIRUௐVXFKௐVHUYLFHVௐDQGௐDQ\ௐ
UHODWHGௐRUGHUௐSURFHVVHV
5HPRXQWௐDQGௐUHIXUELVKHGௐVHUYLFHVௐDUHௐRIIHUHGௐKRZHYHUௐHDFKௐMREௐLVௐTXRWHGௐ LQGHSHQGHQWO\ௐIURPௐRQHௐDQRWKHUௐ7KLVௐLVௐUHTXLUHGௐGXHௐWRௐWKHௐFRPSOH[LW\ௐWRௐUHIXUEௐRUௐ UHPRXQWௐ5HIXUEௐDQGௐUHPRXQWௐSULFLQJௐZLOOௐQRWௐEHௐSDUWௐRIௐWKLVௐVXEPLVVLRQௐKRZHYHUௐ SULFLQJௐFDQௐYDU\ௐGHSHQGLQJௐRQௐWKHௐUHSDLUௐRUௐVHUYLFHௐQHHGHG  'HVFULEHௐ\RXUௐFRPSOLDQFHௐZLWKௐ86ௐ
VWDQGDUGVௐIRUௐWKHௐHTXLSPHQWௐDQGௐSURGXFWVௐ
RIIHUHGௐLQௐ\RXUௐSURSRVDOௐLQFOXGLQJௐ
DSSOLFDEOHௐIHGHUDOௐDQGௐVWDWHௐUHTXLUHPHQWV
3LHUFHௐILUHௐDSSDUDWXVௐDUHௐEXLOWௐZLWKௐSULGHௐDQGௐGHGLFDWLRQௐWRௐDௐSURGXFWௐWKDWௐKHOSVௐ VDYHௐOLYHVௐ:HௐKDYHௐPDQ\ௐLQWHUQDOௐTXDOLW\ௐFKHFNௐSRLQWVௐWKURXJKRXWௐWKHௐEXLOGௐSURFHVVௐ DQGௐEHIRUHௐWKHௐILUHௐDSSDUDWXVௐFDQௐEHௐGHOLYHUHGௐLWௐPXVWௐJRௐWKURXJKௐWKLUGௐSDUW\ௐWHVWLQJௐ E\ௐ8QGHUZULWHUVௐ/DERUDWRULHVௐ
8/

3LHUFHௐFRQWUDFWVௐZLWKௐ8QGHUZULWHU¶Vௐ/DERUDWRULHVௐWRௐLQVSHFWௐ3LHUFHௐDSSDUDWXVௐIRUௐ FRPSOLDQFHௐWRௐ1)3$ௐVWDQGDUGVௐ(YHU\ௐ1)3$ௐ
ௐDSSDUDWXVௐPDQXIDFWXUHGௐLQௐWKHௐ
$SSOHWRQௐIDFLOLW\ௐLVௐUHYLHZHGௐE\ௐDௐ8/ௐFHUWLILHGௐLQVSHFWRUௐDIWHUௐLWௐLVௐFRPSOHWHG (DFKௐDSSDUDWXVௐLVௐVXEMHFWHGௐWRௐDௐYLVXDOௐLQVSHFWLRQௐRIௐFRQVWUXFWLRQௐDQGௐLQVWDOOHGௐ FRPSRQHQWVௐVXFKௐDVௐFKDVVLVௐGULYLQJௐDQGௐFUHZௐFRPSDUWPHQWVௐERG\ௐFRPSDUWPHQWVௐ VWHSVௐZDUQLQJௐOLJKWVௐUHIOHFWLYHௐWULPௐZDUQLQJௐDQGௐLQVWUXFWLRQDOௐODEHOVௐHWFௐ7KHௐ LQVSHFWLRQௐFKHFNOLVWௐEDVHGௐRQௐDSSDUDWXVௐW\SHௐPD\ௐKDYHௐRYHUௐௐLWHPVௐWRௐFKHFN 2QFHௐWKHௐ8/ௐLQVSHFWLRQௐLVௐFRPSOHWHௐDௐFHUWLILFDWLRQௐRIௐ1)3$ௐFRPSOLDQFHௐLVௐSURYLGHGௐ WRௐWKHௐFXVWRPHUௐXSRQௐGHOLYHU\ௐRIௐWKHLUௐILUHௐDSSDUDWXV
2VKNRVKௐ$5))ௐSURGXFWVௐFRPSO\ௐZLWKௐODWHVWௐHGLWLRQௐRIௐ1)3$ௐௐDQGௐWKHௐ)HGHUDOௐ $YLDWLRQௐ$GPLQLVWUDWLRQௐ$GYLVRU\ௐ&LUFXODUௐ
$&
ௐ(

'HVFULEHௐ\RXUௐFRPSOLDQFHௐZLWKௐ&DQDGLDQௐ
VWDQGDUGVௐIRUௐWKHௐHTXLSPHQWௐDQGௐSURGXFWVௐ
RIIHUHGௐLQௐ\RXUௐSURSRVDOௐLQFOXGLQJௐ
DSSOLFDEOHௐIHGHUDOௐDQGௐSURYLQFLDOௐ
UHTXLUHPHQWV
&(57,),('
ௐ8/8/&
1)3$ௐ
ௐ8/ௐ&HUWLILFDWLRQௐ ௐ8/ௐ&DQDGDௐ
8/&
ௐ&HUWLILFDWLRQ
3LHUFHௐLVௐWKHௐILUVWௐILUHௐDSSDUDWXVௐPDQXIDFWXUHUௐWRௐEHௐERWKௐUGௐSDUW\ௐFHUWLILHGௐWRௐ1)3$ௐ 

ௐHGLWLRQௐDQGௐ8/&ௐOLVWHGௐWRௐ&DQDGDௐ8/&6ௐVWDQGDUGௐE\ௐ 8QGHUZULWHUVௐ/DERUDWRULHVௐ6WDJHVௐRIௐWHVWLQJௐLQFOXGHௐURDGௐSXPSௐZHLJKWௐEUDNHௐ SHUIRUPDQFHௐDQGௐDHULDOௐDSSOLFDWLRQௐ$OOௐSURGXFWVௐPXVWௐSDVVௐDOOௐWHVWVௐEHIRUHௐDௐWUXFNௐLVௐ UHOHDVHGௐLQWRௐ&DQDGDௐ7KLVௐFRPPLWPHQWௐWRௐTXDOLW\ௐDSSOLHVௐWRௐWUXFNVௐVROGௐLQௐWKHௐ86ௐ DVௐZHOO
ௐ$OOௐFKDVVLV¶ௐFRPSO\ௐZLWKௐ&DQDGLDQௐ0RWRUௐ9HKLFOHௐ6DIHW\ௐ6WDQGDUGVௐ&0966ௐ 2VKNRVKௐ$5))ௐSURGXFWVௐFRPSO\ௐZLWKௐODWHVWௐHGLWLRQௐRIௐ1)3$ௐௐDQGௐWKHௐ)HGHUDOௐ $YLDWLRQௐ$GPLQLVWUDWLRQௐ$GYLVRU\ௐ&LUFXODUௐ
$&
ௐ(ௐ:HௐZLOOௐZRUNௐZLWKௐWKHௐ
FXVWRPHUௐRQௐVSHFLILFௐ&DQDGLDQௐUHTXLUHPHQWVௐWRௐHQVXUHௐFRPSOLDQFHௐDVௐQHHGHG Bid Number: RFP 113021 Vendor Name: Pierce Manufacturing 













 

EXHIBIT 1 608
Bid Number: RFP 113021 Vendor Name: Pierce Manufacturing Exceptions to Terms, Conditions, or Specifications Form Only those Proposer Exceptions to Terms, Conditions, or Specifications that have been accepted by Sourcewell have been incorporated into the contract text.

Documents
Ensure your submission document(s) conforms to the following:

1. Documents in PDF format are preferred. Documents in Word, Excel, or compatible formats may also be provided.

2. Documents should NOT have a security password, as Sourcewell may not be able to open the file. It is your sole responsibility to ensure that the uploaded document(s) are not either defective, corrupted or blank and that the documents can be opened and viewed by Sourcewell.

3. Sourcewell may reject any response where any document(s) cannot be opened and viewed by Sourcewell.

4. If you need to upload more than one (1) document for a single item, you should combine the documents into one zipped file. If the zipped file contains more than one (1) document, ensure each document is named, in relation to the submission format item responding to. For example, if responding to the Marketing Plan category save the document as "Marketing Plan." Pricing - Table 12. Pricing.zip - Tuesday November 30, 2021 15:16:30 Financial Strength and Stability - Table 2. Financial Strength and Stability.zip - Tuesday November 30, 2021 14:31:23 Marketing Plan/Samples - Table 7. Marketing Plan.Samples.zip - Tuesday November 30, 2021 13:40:24 WMBE/MBE/SBE or Related Certificates (optional)
Warranty Information - Table 9. Warranty Information.zip - Tuesday November 30, 2021 13:41:02 Standard Transaction Document Samples - SALES_TEMPLATE_Sales Proposal Order Form .pdf - Tuesday November 30, 2021 13:43:12
Upload Additional Document - Additional Documents.zip - Tuesday November 30, 2021 16:02:10 













 

EXHIBIT 1 609
$GGHQGD7HUPVDQG&RQGLWLRQV
352326(5$)),'$9,7$1'$6685$1&(2)&203/,$1&(
,FHUWLI\WKDW,DPWKHDXWKRUL]HGUHSUHVHQWDWLYHRIWKH3URSRVHUVXEPLWWLQJWKHIRUHJRLQJ3URSRVDOZLWKWKHOHJDODXWKRULW\WRELQGWKH 3URSRVHUWRWKLV$IILGDYLWDQG$VVXUDQFHRI&RPSOLDQFH

 7KH3URSRVHULVVXEPLWWLQJWKLV3URSRVDOXQGHULWVIXOODQGFRPSOHWHOHJDOQDPHDQGWKH3URSRVHUOHJDOO\H[LVWVLQJRRGVWDQGLQJLQ WKHMXULVGLFWLRQRILWVUHVLGHQFH
 7KH3URSRVHUZDUUDQWVWKDWWKHLQIRUPDWLRQSURYLGHGLQWKLV3URSRVDOLVWUXHFRUUHFWDQGUHOLDEOHIRUSXUSRVHVRIHYDOXDWLRQIRU FRQWUDFWDZDUG
 7KH3URSRVHULQFOXGLQJDQ\SHUVRQDVVLVWLQJZLWKWKHFUHDWLRQRIWKLV3URSRVDOKDVDUULYHGDWWKLV3URSRVDOLQGHSHQGHQWO\DQGWKH 3URSRVDOKDVEHHQFUHDWHGZLWKRXWFROOXGLQJZLWKDQ\RWKHUSHUVRQFRPSDQ\RUSDUWLHVWKDWKDYHRUZLOOVXEPLWDSURSRVDOXQGHU WKLVVROLFLWDWLRQ
DQGWKH3URSRVDOKDVLQDOOUHVSHFWVEHHQFUHDWHGIDLUO\ZLWKRXWDQ\IUDXGRUGLVKRQHVW\7KH3URSRVHUKDVQRW GLUHFWO\RULQGLUHFWO\HQWHUHGLQWRDQ\DJUHHPHQWRUDUUDQJHPHQWZLWKDQ\SHUVRQRUEXVLQHVVLQDQHIIRUWWRLQIOXHQFHDQ\SDUWRI WKLVVROLFLWDWLRQRURSHUDWLRQVRIDUHVXOWLQJFRQWUDFW DQGWKH3URSRVHUKDVQRWWDNHQDQ\DFWLRQLQUHVWUDLQWRIIUHHWUDGHRU FRPSHWLWLYHQHVVLQFRQQHFWLRQZLWKWKLVVROLFLWDWLRQ$GGLWLRQDOO\LI3URSRVHUKDVZRUNHGZLWKDFRQVXOWDQWRQWKH3URSRVDOWKH FRQVXOWDQW
DQLQGLYLGXDORUDFRPSDQ\
KDVQRWDVVLVWHGDQ\RWKHUHQWLW\WKDWKDVVXEPLWWHGRUZLOOVXEPLWDSURSRVDOIRUWKLV VROLFLWDWLRQ
 7RWKHEHVWRILWVNQRZOHGJHDQGEHOLHIDQGH[FHSWDVRWKHUZLVHGLVFORVHGLQWKH3URSRVDOWKHUHDUHQRUHOHYDQWIDFWVRU FLUFXPVWDQFHVZKLFKFRXOGJLYHULVHWRDQRUJDQL]DWLRQDOFRQIOLFWRILQWHUHVW$QRUJDQL]DWLRQDOFRQIOLFWRILQWHUHVWH[LVWVZKHQD YHQGRUKDVDQXQIDLUFRPSHWLWLYHDGYDQWDJHRUWKHYHQGRU¶VREMHFWLYLW\LQSHUIRUPLQJWKHFRQWUDFWLVRUPLJKWEHLPSDLUHG  7KHFRQWHQWVRIWKH3URSRVDOKDYHQRWEHHQFRPPXQLFDWHGE\WKH3URSRVHURULWVHPSOR\HHVRUDJHQWVWRDQ\SHUVRQQRWDQ HPSOR\HHRUOHJDOO\DXWKRUL]HGDJHQWRIWKH3URSRVHUDQGZLOOQRWEHFRPPXQLFDWHGWRDQ\VXFKSHUVRQVSULRUWR'XH'DWHRIWKLV VROLFLWDWLRQ
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

 7KH3URSRVHUZLOOFRPSO\ZLWKDOODSSOLFDEOHSURYLVLRQVRIIHGHUDOVWDWHDQGORFDOODZVUHJXODWLRQVUXOHVDQGRUGHUV  7KH3URSRVHUXQGHUVWDQGVWKDW6RXUFHZHOOZLOOUHMHFW5)3SURSRVDOVWKDWDUHPDUNHGFRQILGHQWLDO RUQRQSXEOLFHWF
HLWKHU
VXEVWDQWLDOO\RULQWKHLUHQWLUHW\8QGHU0LQQHVRWD6WDWXWHV6HFWLRQ VXEGLYLVLRQDOOSURSRVDOVDUHFRQVLGHUHGQRQSXEOLF GDWDXQWLOWKHHYDOXDWLRQLVFRPSOHWHDQGD&RQWUDFWLVDZDUGHG$WWKDWSRLQWSURSRVDOVEHFRPHSXEOLFGDWD0LQQHVRWD6WDWXWHV 6HFWLRQSHUPLWVRQO\FHUWDLQQDUURZO\GHILQHGGDWDWREHFRQVLGHUHGDWUDGHVHFUHWDQGWKXVQRQSXEOLFGDWDXQGHU 0LQQHVRWD
V'DWD3UDFWLFHV$FW
 3URSRVHULWVHPSOR\HHVDJHQWVDQGVXEFRQWUDFWRUVDUHQRW

 ,QFOXGHGRQWKH³6SHFLDOO\'HVLJQDWHG1DWLRQDOVDQG%ORFNHG3HUVRQV´OLVWPDLQWDLQHGE\WKH2IILFHRI)RUHLJQ$VVHWV&RQWURO RIWKH8QLWHG6WDWHV'HSDUWPHQWRIWKH7UHDVXU\IRXQGDW KWWSV
ZZZWUHDVXU\JRYRIDFGRZQORDGVVGQOLVWSGI

 ,QFOXGHGRQWKHJRYHUQPHQWZLGHH[FOXVLRQVOLVWVLQWKH8QLWHG6WDWHV6\VWHPIRU$ZDUG0DQDJHPHQWIRXQGDW

KWWSV
VDPJRY6$0
RU
 3UHVHQWO\GHEDUUHGVXVSHQGHGSURSRVHGIRUGHEDUPHQWGHFODUHGLQHOLJLEOHRUYROXQWDULO\H[FOXGHGIURPSURJUDPVRSHUDWHG Bid Number: RFP 113021 Vendor Name: Pierce Manufacturing 













 

EXHIBIT 1 610
E\WKH6WDWHRI0LQQHVRWD
WKH8QLWHG6WDWHVIHGHUDOJRYHUQPHQWRUWKH&DQDGLDQJRYHUQPHQWDVDSSOLFDEOH RUDQ\
3DUWLFLSDWLQJ(QWLW\9HQGRUFHUWLILHVDQGZDUUDQWVWKDWQHLWKHULWQRULWVSULQFLSDOVKDYHEHHQFRQYLFWHGRIDFULPLQDORIIHQVH UHODWHGWRWKHVXEMHFWPDWWHURIWKLVVROLFLWDWLRQ
%\FKHFNLQJWKLVER[,DFNQRZOHGJHWKDW,DPERXQGE\WKHWHUPVRIWKH3URSRVHU¶V$IILGDYLWKDYHWKHOHJDODXWKRULW\WRVXEPLWWKLV 3URSRVDORQEHKDOIRIWKH3URSRVHUDQGWKDWWKLVHOHFWURQLFDFNQRZOHGJPHQWKDVWKHVDPHOHJDOHIIHFWYDOLGLW\DQGHQIRUFHDELOLW\DVLI, KDGKDQGVLJQHGWKH3URSRVDO7KLVVLJQDWXUHZLOOQRWEHGHQLHGVXFKOHJDOHIIHFWYDOLGLW\RUHQIRUFHDELOLW\VROHO\EHFDXVHDQHOHFWURQLF VLJQDWXUHRUHOHFWURQLFUHFRUGZDVXVHGLQLWVIRUPDWLRQ0LFKHOOH6ZRNRZVNL6DOHV2SHUDWLRQV0DQDJHU2VKNRVK&RUSRUDWLRQ 3LHUFH0DQXIDFWXULQJ2VKNRVK$LUSRUW3URGXFWV
7KH3URSRVHUGHFODUHVWKDWWKHUHLVDQDFWXDORUSRWHQWLDO&RQIOLFWRI,QWHUHVWUHODWLQJWRWKHSUHSDUDWLRQRILWVVXEPLVVLRQDQGRUWKH 3URSRVHUIRUHVHHVDQDFWXDORUSRWHQWLDO&RQIOLFWRI,QWHUHVWLQSHUIRUPLQJWKHFRQWUDFWXDOREOLJDWLRQVFRQWHPSODWHGLQWKHELG <HV 1R
7KH%LGGHUDFNQRZOHGJHVDQGDJUHHVWKDWWKHDGGHQGXPDGGHQGDEHORZIRUPSDUWRIWKH%LG'RFXPHQW &KHFNWKHER[LQWKHFROXPQ,KDYHUHYLHZHGWKLVDGGHQGXPEHORZWRDFNQRZOHGJHHDFKRIWKHDGGHQGD )LOH1DPH
,KDYHUHYLHZHGWKH
EHORZDGGHQGXPDQG
DWWDFKPHQWV
LI

DSSOLFDEOH

3DJHV
$GGHQGXPBB)LUHB$SSDUDWXVB5)3B
6DW1RYHPEHU
30 
$GGHQGXPBB)LUHB$SSDUDWXVB5)3B
7KX1RYHPEHU

30 
$GGHQGXPBB)LUHB$SSDUDWXVB5)3B
)UL2FWREHU


$0 
$GGHQGXPBB)LUHB$SSDUDWXVB5)3B
)UL2FWREHU


$0 
Bid Number: RFP 113021 Vendor Name: Pierce Manufacturing 













 

EXHIBIT 1 611
The
New York State
Contract Reporter
This document printed
Monday, 10/11/2021
NYS' official source of contracting opportunities
Bringing business and government together
Contracting Opportunity
* * * This ad has not been published. It has been reviewed and pending publication. * * * Title: Firefighting Apparatus and Fire Service Vehicles Agency: Sourcewell
Division: Procurement Department
Contract Number: 113021
Contract Term: 4 years, with potential 1 year extension Date of Issue: 10/12/2021
Due Date/Time: 11/30/2021 4:30 PM
Central Time
County(ies): All NYS counties
Classification: Safety & Security - Commodities
Opportunity Type: General
Entered By: Chris Robinson
Description: Sourcewell, a State of Minnesota local government unit and service cooperative, is requesting proposals for Firefighting Apparatus and Fire Service Vehicles to result in a contracting solution for use by its Participating Entities.  Sourcewell Participating Entities include thousands of governmental, higher education, K-12 education, nonprofit, tribal government, and other public agencies located in the United States and Canada. A full copy of the Request for Proposals can be found on the Sourcewell Procurement Portal [https://proportal .sourcewell-mn.gov]. Only proposals submitted through the Sourcewell Procurement Portal will be considered.

Proposals are due no later than November 30, 2021, at 4:30 p.m. Central Time, and late proposals will not be considered.

Service-Disabled Veteran-Owned Set Aside: No
1 of 2
EXHIBIT 1 612
Contact Information
Primary contact: Sourcewell
Procurement Department
Chris Robinson
Procurement Manager
202 12th Street NE
P.O. Box 219
Staples, MN 56479
United States
Ph: 218-895-4168
[email protected]
Submit to contact: Sourcewell
Procurement Department
Chris Robinson
Procurement Manager
202 12th Street NE
P.O. Box 219
Staples, MN 56479
United States
Ph: 218-895-4168
[email protected]
© 2021, Empire State Development http://www.esd.ny.gov/ 2 of 2
EXHIBIT 1 613
EXHIBIT 1 614
EXHIBIT 1 615
Adportal Self Service Advertising Confirmation https://placelegal.mcclatchy.com/legals/columbia/home/confirmation.htm... 1 of 1 10/7/2021, 9:26 AM
EXHIBIT 1 616
SPORTS USA TODAY ❚ TUESDAY, OCTOBER 12, 2021 ❚ 5C
GET NOTICED! [email protected]

HEALTH/FITNESS
If you or a loved one has
been diagnosed with
ovarian cancer after using
talcum based products
you may be entitled to
significant compensation
800-208-3526
TALCUM
POWDER

SETTLEMENT
Place your ad in USA TODAY
Marketplace! Call: 800-397-0070
ELIMINATE your
overwhelming debt
We can help if your total
debt is $10,000 or more!
Avoid bankruptcy today and
start over completely debt-free.
800-825-1306
THE CALL IS FREE.

CREDIT CARD DEBT

MEDICAL DEBT

PERSONAL LOANS

FINANCIAL

FINANCIAL

IMPROVE

YOUR CREDIT
SCORE
Are you getting hit
with high interest rates
because of a low credit
score? Improve it today!
800-852-4931
FREE Consultation
FREE Credit Evaluation

HAVE YOU BEEN

CLASSIFIED AS A HIGH

RISK DRIVER DUE TO DUI,

DWI OR TICKETS FOR
AGGRESSIVE DRIVING?
THE CALL & QUOTE ARE FREE.
800-509-9315
Serenity is here
to help by making SR-22
insurance easy to get and
affordable for everyone.

ANNOUNCEMENTS
A Garden Observed:

Cultivating A Life
by Melanie Boyer
Enchanting 220 page
coffee-table devotional filled
with garden photography
Available on Amazon
A Garden Observed:

Cultivating A Life
by Melanie Boyer
Enchanting 220 page
coffee-table devotional filled
with garden photography
Available on Amazon
d:
e
er
ge
d
hy
on

BOOKS / PUBLICATIONS

MARKETPLACE
To view more Classified listings,
visit: classifieds.usatoday.com

BUSINESS PRIVATE MORTGAGE INVESTORS
WANTED (20% RETURN IN 120
DAYS) Vx 100% Self Sustainable
Intelligent Homes JUST IMAGINE

NEVER HAVING A POWER BILL,

A HEATING BILL,A WATER BILL,AN
INTERNET BILL or even a CELL
PHONE BILL!!! INVESTMENT
OPPORTUNITY Please go to the
below facebook link to watch our video
https://www.facebook.com/story.
php?story_fbid=35763229276
2102&id=109613270897340
We pay 20% return for putting up the
capital to build the homes where the
private mortgage investor owns the home
until our buyer pays them out in less
than 120 days! PH or TXT 249-525-7238
or [email protected]

BEAUTIFUL TENNESSEE

VALLEY FARM
60ac Brick (2011) Home 4,300 sf
Lake, River, Original Log cabin
$2.2M Near Chattanooga.
www.TennesseeValleyFarm.com
Call: 423-987-1570

REAL ESTATE

MARKETPLACE

BUSINESS

OPPORTUNITES

SUCCESSFUL

ADVERTISEMENTS
start with

USA TODAY
Marketplace
1-800-397-0070
Notice to Bidders
Region 14 ESC (the “Lead Agency”), on behalf of National Cooperative Purchasing Alliance (NCPA) and public agencies in all 50 states, that elect to access the Master Agreement is soliciting proposals to enter into Master Agreements for:
• AI Contract Review Software and Contract Organization Services #23-21
• Control Room Console Solutions #24-21
• Cyber-Security Solutions, Malware, Ransomware Protection, Other Related Products and Services #34-21
• Digital Healthcare Diagnostic Testing and Related Products and Services #25-21
• Digital Healthcare Guidance – Pharmacy #26-21
• Digital Healthcare Guidance – Surgical Consulting #27-21 • Electrical Power System and Electronics Systems Protection Consulting and related Products and Services #28-21
• HVAC Equipment, Installation, Service, Building Control Systems & Related Products and Services #32-21
• Medical Supplies and Related Goods and Services #29-21 • Parking and Mobility Consulting #31-21
• Playground Equipment, Outdoor Fitness Equipment, Site Furnishings, Surfacing and Related Products/Services #35-21 • Public Sector Operations, and Financial Management
Software and Consulting Services #30-21
• Vehicle Wash Systems and Related Services #33-21
Due Thursday, November 18, 2021 at 2:00 pm CST
Responses shall be received electronically no later than the submittal deadline via our online Bonfire portal at ncpa.bonfirehub.com.

To request a copy of specifications, please visit
NCPA’s website www.ncpa.us.

Sourcewell, a State of Minnesota local government unit and service cooperative, is requesting proposals for Firefighting Apparatus and Fire Service Vehicles to result in a
contracting solution for use by its Participating Entities.

Sourcewell Participating Entities include thousands of
governmental, higher education, K-12 education,
nonprofit, tribal government, and other public agencies located in the United States and Canada.

A full copy of the Request for Proposals can be
found on the Sourcewell Procurement Portal
https://proportal.sourcewell-mn.gov.

Only proposals submitted through the Sourcewell
Procurement Portal will be considered.

Proposals are due no later than November 30, 2021, at 4:30pm Central Time, and late proposals will not be considered

NOTICES

PUBLIC NOTICE

PUBLIC NOTICE
Week 5 in the NFL was a wild one.

Three of the early-window games –
not counting the Falcons topping the
Jets in the really early window in London – came down to electric finishes.

And the Packers, Patriots and Vikings
won their games on field goals at or near
the end of regulation or in overtime, on a
day in which placekickers struggled at
historic levels.

We also saw an upstart team with a
rookie coach, the Chargers, outlast another powerful AFC opponent in the Browns in what could end up being a potential playoff preview. The same went for a rematch of last year’s AFC championship game, though this time it was the Bills who prevailed over the Chiefs in
convincing fashion.

Elsewhere, a rough week got tougher
for embattled Jaguars coach Urban
Meyer, who saw his team drop to 0-5.

The Week 5 winners and losers:

WINNERS
The (AFC West favorite?) Chargers
In the track meet that was a 47-42
victory, the Chargers outslugged a worthy contender in the AFC, the Browns.

Questions about defensive lapses
abound for both teams, but that the
Chargers had to battle back from a 14-
point, third-quarter deficit shows how
far Los Angeles (4-1) has come in Brandon Staley’s first season as head coach.

First, let’s highlight what the Chargers did do well on defense. One of the main reasons Los Angeles was able to
keep the deficit manageable was because in three of Cleveland’s first five trips inside the red zone, it clamped
down and forced the Browns to settle for
two short field goals and forced one
turnover on downs. But quarterback
Justin Herbert is quickly becoming one
of the young star passers in the entire
NFL. Herbert is on a historic pace in his
young career, bolstered by his 26 of 43
performance against the Browns for 398
yards with four touchdowns. He also
added a rushing score. He could be on a
track to insert himself in the MVP conversation. More important, with the Chiefs looking vulnerable – especially
on defense – the Chargers could even
threaten for the division crown.

Not only offense in Arizona
A team coached by Kliff Kingsbury always was going to have dynamic playmakers on offense. But the Cardinals have remained the lone undefeated
team in the NFL also because of a really
talented and efficient defense. Going up
against a dynamic athlete and passer in
49ers rookie Trey Lance, who was making his first career start, the Cardinals prevailed 17-10.

Arizona was excellent in high-leverage situations. The Cardinals limited the 49ers to 3 of 11 conversions on third
downs, kept the Niners out of the end
zone in their only goal-to-go scenario of
the game and stopped San Francisco on
fourth downs on four out of five tries.

According to Elias Sports Bureau, it was
the only time in at least the last 40 seasons that a team recorded four fourthdown stops in a game. The Cardinals will start to have a target on their backs,
but having a now-improved defense
makes this team that much more dangerous because it won’t be incumbent on quarterback Kyler Murray and the
Arizona offense to carry the team.

The losing Lions
Yes, they fell in heartbreak, again.

And players and coaches in the NFL almost never want to hear about silver linings. But what rookie coach Dan Campbell is doing in Detroit, getting his team to punch above its weight and nearly
pull off two improbable upsets in two
weeks, should be admired. The Lions
lost to the Vikings 19-17 on a crushing
game-winning field goal after Detroit
had battled back from a 10-point deficit
with a little more than five minutes left
to play. This came one week after the Lions lost (also 19-17) when Ravens kicker Justin Tucker set an NFL record with a
66-yard, game-winning field goal.

In both cases, the Lions gave up big
passing plays to put their opponents
near field goal range. Those are issues
the team needs to clean up. This Lions
roster is still young and has a lot of
holes. Jared Goff is not a long-term answer at quarterback. But Detroit ranks second in third-down defense (27.78%)
and has become a high-effort team.

That has kept it in these games. If
Campbell can keep developing the talent the Lions have and if the Lions improve their roster over the next couple of seasons, Detroit could be a team to
watch in the near future.

LOSERS
Kickers
The NFL, when it changed its rule in
2015 to push back the extra point, wanted the play to have more drama. In Week 5, the league got its wish. There were 12
missed extra points before Monday’s
game. Extra points weren’t the only
kicking struggle. There have also been
12 missed field goals. This shouldn’t
necessarily be chalked up to any bigpicture issues or problematic trend; every now and then, a week comes by where this just seems to happen. This
one, however, was the worst kicking
performance since the rule change.

What makes this case interesting,
though, is that weather typically plays a
factor in poor kicking. This week, games
were not affected by inclement weather.

In particular, the Packers’ 25-22 overtime victory against the Bengals offered a study of kicking comedy. At one point,
Mason Crosby of the Packers and Evan
McPherson of the Bengals combined for
five consecutive missed field goal kicks
in a stretch of fewer than eight minutes
of game time – and it happened in the
fourth quarter and overtime. And, if
there were a missed extra point in Monday’s game between the Colts and Ravens, it will set a record for the most combined missed extra points across the entire league in a week.

Urban Meyer
With each passing day, Urban Meyer
is showing that the head coaching job of
the Jaguars is too big for him. It wasn’t
so much that the Jaguars lost to the AFC
South rival Titans 37-19. It was the effort
they showed. Early in the third quarter,
with Tennessee holding an 11-point lead,
the Jaguars defense did not look interested in tackling Titans running back Derrick Henry on a 9-yard TD rush.

It’s no surprise that effort was an issue. This entire week was shrouded in controversy over Meyer’s decision to
stay in Ohio after a loss to the Bengals,
missing the team flight. He was later
filmed at a bar, where a woman who was
not his wife danced on him. It would be
natural for players to question his commitment.

After the incident in Ohio, owner
Shad Khan issued a strong statement
and said Meyer “must regain our trust
and respect.” Yet Meyer has repeatedly
failed to hold himself accountable and
routinely blames others for mistakes,
even his players. After Sunday’s loss, reporters asked him about a 4th-and-1 call and why Trevor Lawrence didn’t keep it
on a quarterback sneak. Meyer said
Lawrence was “not quite comfortable
with that yet” and added “I don’t micromanage who is in the game.” Minutes later, Lawrence disagreed and said that
while it wasn’t something they had done
in a game yet, that he was “comfortable.” This team has had bouts of mental mistakes and communications issues,
careless penalties, carelessness with
the ball. And it all falls on Meyer.

Brian Flores and Chris Grier
Memories of Miami’s surprise 10-win
season in coach Brian Flores’ second
season with the Dolphins feel so long
ago. And after the defending Super Bowl
champion Buccaneers throttled the Dolphins 45-17, both Flores and general manager Chris Grier have some signifi-
cant questions to answer. The Tampa
Bay roster is better than Miami’s. It
might be the best in the entire league.

But Flores, a coach with a specialty on
defense, spent 15 seasons on the Patriots coaching staff, each of those when Tom Brady played in New England. He
should have at least a decent idea of
how to fluster Brady.

Instead, Brady completed 30 of 41
passes for 411 yards with four TDs. The
Bucs failed to convert only three of their
11 third-down attempts. And Tampa Bay
gained 558 yards of total offense in what
was simply a defensive collapse for Miami (1-4). While Grier has hit on some of his recent draft picks, his inability to fix
holes at running back, linebacker, offensive line and quarterback are concerning. Though second-year passer Tua Tagovailoa has been sidelined with broken ribs, Grier will always have to face questions of how Miami passed on Justin Herbert, who has been a revelation for
the Chargers and was taken one pick after Tagovailoa was. It’s too early for a total cleaning house, but if more performances like this follow, that time may be quickly nearing.

The Panthers as NFC disruptors
They had a hot start to the season,
but after consecutive losses Carolina
has regressed to the mean. Granted, last
week’s defeat came against a powerful
Cowboys team and both have been with
star running back Christian McCaffrey
sidelined. But Carolina (3-2) blew a 12-
point lead it held in the second quarter
and squandered several chances to extend their lead in a disappointing 21-18 loss against the Eagles.

Carolina’s defense held its end of the
bargain early in the game. Other than
the three first downs the unit gave up on
Philadelphia’s end-of-half drive in the
second quarter, the Panthers had allowed the Eagles to move the chains just twice in their other 10 possessions to
start the game. The Panthers defense
constantly put the offense in great field
position, but Carolina stalled when it
got into plus territory. Quarterback Sam
Darnold has now thrown five interceptions in the last two weeks after tossing three against the Eagles. Though there
were other shortcomings, his inability
to move the ball when Philly brought
pressure doomed the Panthers. The
special teams unit allowing the Eagles
to block a punt with four minutes left in
the game set up the game-winning
touchdown. But don’t lose sight of the
throw Darnold missed to receiver Robby
Anderson on third down. These are the
games Carolina needs to win to be a
contender in the conference. This loss
shows the Panthers still have some
work to do to get there.

NFL WEEK 5 WINNERS AND LOSERS
Chargers bolting up, Jaguars spiraling
Lorenzo Reyes

USA TODAY
First-year NFL head coach Urban Meyer’s Jaguars fell to 0-5 on Sunday and Jacksonville has lost 20 consecutive games. BOB SELF/THE FLORIDA TIMES-UNION EXHIBIT 1 617
EXHIBIT 1
618
EXHIBIT 1
619
EXHIBIT 1
620
EXHIBIT 1
621
EXHIBIT 1
622
Notice
Basic Information
Details
Dates
Contact Information
Pre-Bidding Events
Bid Submission Process
Estimated Contract Value (CAD) $800,000,000.00 (Not shown to suppliers) Reference Number 0000210048
Issuing Organization Sourcewell
Owner Organization
Solicitation Type RFP - Request for Proposal (Formal)
Solicitation Number 113021
Title Firefighting Apparatus and Fire Service Vehicles
Source ID PP.CO.USA.868485
Location All of Canada, All of Canada
Purchase Type Duration:4 years
Description Sourcewell, a State of Minnesota local government unit and service cooperative, is requesting proposals for Firefighting Apparatus and Fire Service Vehicles to result in a contracting solution for use by its Participating Entities. Sourcewell Participating Entities include thousands of governmental, higher education, K-12 education, nonprofit, tribal government, and other public agencies located in the United States and Canada. A full copy of the Request for Proposals can be found on the Sourcewell Procurement Portal [https://proportal.sourcewell-mn.gov]. Only proposals submitted through the Sourcewell Procurement Portal will be considered. Proposals are due no later than November 30, 2021, at 4:30 p.m. Central Time, and late proposals will not be considered.

Publication Manual publication
Question Acceptance Deadline 2021/11/19 05:30:00 PM EST Questions are submitted online No
Bid Intent Not Available
Closing Date 2021/11/30 05:30:00 PM EST
Prebid Conference 2021/11/02 11:00:00 AM EDT
Procurement Department
218-894-1930
[email protected]
Event Type Prebid Conference
Attendance Recommended
Event date 2021/11/02 11:00:00 AM EDT
Location Online Conference
Event Note Login information will be emailed two business days prior to the event.

Bid Submission Type Electronic Bid Submission
Pricing In attached document
Pricing In attached document
Bid Documents List
Item Name Description Mandatory
Bid Documents Documents defining the proposal Yes
113021 - Firefighting Apparatus and Fire Service Vehicles 2021/10/12 09:26:56 AM EDT Page 1 of2
EXHIBIT 1 623
Categories
Selected Categories
GSIN Categories (8)
G Goods
Goods
N42 Firefighting, Rescue, And Safety Equipment
Firefighting, Rescue, And Safety Equipment
N4210P FIREFIGHTING EQUIPMENT - COMPLETE FIRE TRUCKS AND TRAILERS ONLY

FIREFIGHTING EQUIPMENT - COMPLETE FIRE TRUCKS AND TRAILERS ONLY N4210K PUMPING EQUIPMENT, PORTABLE (FIREFIGHTING, GROUND)

PUMPING EQUIPMENT, PORTABLE (FIREFIGHTING, GROUND)
N42 Fire Fighting Equipment
Fire Fighting Equipment
N4210 FIRE FIGHTING EQUIPMENT

FIRE FIGHTING EQUIPMENT
N4210W FIREFIGHTING EQUIPMENT, SPECIAL, CUSTOMER OR SYSTEMS ENGINEERED PRODUCTS

FIREFIGHTING EQUIPMENT, SPECIAL, CUSTOMER OR SYSTEMS ENGINEERED PRODUCTS N4210B GROUND FIRE FIGHTING EQUIPMENT

GROUND FIRE FIGHTING EQUIPMENT
N4200 FIREFIGHTING, RESCUE AND SAFETY EQUIPMENT
Firefighting, rescue and safety equipment
N4210PD TRUCK, FIREFIGHTING

TRUCK, FIREFIGHTING
MERX Category (1)
G Goods
Goods
G14 Fire Fighting, Security and Safety Equipment
Fire Fighting, Security and Safety Equipment
UNSPSC Category (1)
25000000 Commercial and Military and Private Vehicles and their Accessories and Components 25100000 Motor vehicles
25101700 Safety and rescue vehicles
113021 - Firefighting Apparatus and Fire Service Vehicles 2021/10/12 09:26:56 AM EDT Page 2 of2
EXHIBIT 1 624
Acres Industries, Inc.

Alexis Fire Equipment
Company BME Fire Trucks, LLC
Brindlee Mountain Fire
Apparatus, LLC

CAMIONS CARL THIBAULT,
INC. CET Fire Pumps MFG Chemical Containers, Inc.

Custom Fire Apparatus,
Inc.

Dependable Truck & Tank,
Limited EJ Metals, LLC EͲONE, Inc. FireStopper USA MD Fort Garry FIre Trucks, Ltd. Fouts Brothers, Inc.

HiͲTech Emergency
Vehicle Service, Inc. HME, Incorporated
HUB Fire Engines &
Equipment, Ltd.

Possible Points
Conformance to Terms/
Conditions to Include
Documentation 50 38 41 36 41 38 40 33 43 35 40 43 28 42 37 39 43 36 Pricing 400 333 299 298 278 311 315 305 320 265 325 319 263 271 310 306 319 260 Financial, Industry and
Marketplace Successes 75 52 57 52 59 55 56 55 60 51 55 65 27 61 59 61 60 52 Bidder's Ability to Sell/
Service Contract Nationally 100 64 77 71 80 71 75 67 75 67 72 88 34 79 71 72 77 65 Bidder's Marketing Plan 50 35 42 34 39 37 42 34 44 38 35 39 34 43 38 38 40 35 Value Added Attributes 75 56 50 42 51 56 56 44 60 44 57 60 51 65 57 58 58 57 Warranty Coverages and
Information 50 43 43 40 41 43 40 36 38 40 39 44 37 45 42 42 42 39 Selection and Variety of
Products and Services Offered 200 158 156 140 163 164 151 145 169 146 157 180 116 169 156 151 165 151 Total Points 1,000 779 765 713 752 775 775 719 809 686 780 838 590 775 770 767 804 695 Rank Order 14202622161625 73013 433161819 829
Laszlo Corporation Marion Body Works, Inc. MAXIMETAL, INC. Metalfab, LTD P.L. Custom Body and
Equipment Co., Inc. Pierce Manufacturing Rock River Industries, LLC Rosenbauer South
Dakota, LLC Skeeter Brush Trucks, LLC
Spencer Manufacturing,
Inc.

Super Vacuum
Manufacturing CO, Inc. The Sutphen Corporation Toyne, Inc. Ty Parker & Son, Inc. US Fire Equipment, LLC Ward Apparatus, LLC Possible Points
Conformance to Terms/
Conditions to IncludeDocumentation 50 28 40 44 34 44 45 43 44 39 39 44 44 41 33 31 41 Pricing 400 253 303 318 301 334 321 324 300 275 271 271 323 311 245 334 270 Financial, Industry and
Marketplace Successes 75 41 61 63 49 64 65 59 64 57 54 62 62 61 47 53 55 Bidder's Ability to Sell/
Service Contract Nationally 100 60 72 85 67 80 90 73 87 72 70 86 87 79 66 68 74 Bidder's Marketing Plan 50 33 41 45 35 43 44 41 44 36 33 45 44 40 34 34 38 Value Added Attributes 75 52 59 64 45 63 65 58 58 43 49 60 63 52 43 49 53 Warranty Coverages andInformation 50 39 43 43 37 44 43 42 44 42 41 44 44 42 33 39 42 Selection and Variety of
Products and Services Offered 200 110 165 169 141 168 179 162 179 148 170 173 176 166 120 154 158 Total Points 1,000 616 784 831 709 840 852 802 820 712 727 785 843 792 621 762 731 Rank Order 32 12 528 3 1 9 627 24 11 210 31 21 23
___________________________________________ ________________________________________ _____________________________ _________________________________ Kim Austin, MBA, CPPB, Procurement Lead Analyst Stephanie Haataja, CPIM, Procurement Analyst Craig West, Procurement Analyst Tom Sharbonno, Procurement Analyst Proposal Evaluation
Firefighting Apparatus and Fire Service Vehicles RFP #113021 






 




EXHIBIT 1
625
Proposal Opening Record
Date of opening:November 30, 2021
Sourcewell posted Request for Proposal #113021, for the procurement of Firefighting Apparatus and Fire Service Vehicles, on the Sourcewell Procurement Portal [proportal.sourcewellͲmn.gov] on Tuesday, October 12, 2021, and the solicitation remained in an open status within the portal until November 30, 2021, at 4:30 pm CT. The RFP required that all proposals be submitted through the Sourcewell Procurement Portal no later than 4:30 pm CT on November 30, 2021, the date and time specified in the Solicitation Schedule.

The undersigned certify that all responses received on Request for Proposal #113021 were submitted through the Sourcewell Procurement Portal, and that each Proposer’s response material was digitally sealed upon submission and remained inaccessible until the due date and time specified in the Solicitation Schedule.

Responses were received from the following:

Acres Industries, Inc.ͲSubmitted 11/30/21 at 12:48:29 PM Alexis Fire Equipment CompanyͲSubmitted 11/30/21 at 4:27:23 PM BME Fire Trucks, LLCͲSubmitted 11/30/21 at 9:37:36 AM Brindlee Mountain Fire Apparatus, LLCͲSubmitted 11/30/21 at 12:59:24 PM CAMIONS CARL THIBAULT, INC.ͲSubmitted 11/21/21 at 3:03:05 PM CET Fire Pumps MFGͲSubmitted 11/30/21 at 3:18:40 PM
Chemical Containers, Inc.ͲSubmitted 11/22/21 at 8:59:01 AM Custom Fire Apparatus, Inc.ͲSubmitted 11/29/21 at 4:20:32 PM Dependable Truck & Tank, LimitedͲSubmitted 11/30/21 at 1:30:44 PM EJ Metals, LLCͲSubmitted 11/30/21 at 12:29:54 PM
EͲONE, Inc.ͲSubmitted 11/30/21 at 4:23:32 PM
FireStopper USA MDͲSubmitted 11/22/21 at 11:37:18 AM
Fort Garry Fire Trucks, Ltd.ͲSubmitted 11/29/21 at 11:48:34 AM Fouts Brothers, Inc.ͲSubmitted 11/30/21 at 10:27:18 AM HiͲTech Emergency Vehicle Service, Inc.ͲSubmitted 11/30/21 at 3:51:27 PM HME, IncorporatedͲSubmitted 11/29/21 at 2:42:09 PM
HUB Fire Engines & Equipment, Ltd.ͲSubmitted 11/30/21 at 10:50:26 AM Laszlo CorporationͲSubmitted 11/30/21/at 12:55:22 PM
Marion Body Works, Inc.ͲSubmitted 11/23/21 at 9:03:20 AM MAXIMETAL, INC.ͲSubmitted 11/27/21 at 8:17:02 AM
Metalfab, LTDͲSubmitted 11/29/21 at 11:44:08 AM
P.L. Custom Body and Equipment Co., Inc.ͲSubmitted 11/29/21 at 3:15:41 PM Pierce ManufacturingͲSubmitted 11/30/21 at 4:18:31 PM Rock River Industries, LLCͲSubmitted 11/29/21 at 11:40:39 AM Rosenbauer South Dakota, LLCͲSubmitted 11/30/21 at 8:35:18 AM 





 

 


EXHIBIT 1 626
Skeeter Brush Trucks, LLCͲSubmitted 11/30/21 at 12:29:14 PM Spencer Manufacturing, Inc.ͲSubmitted 11/30/21 at 2:53:05 PM Super Vacuum Manufacturing CO., Inc.ͲSubmitted 11/30/21 at 2:46:11 PM The Sutphen CorporationͲSubmitted 11/30/21 at 12:43:06 PM Toyne, Inc.ͲSubmitted 11/29/21 at 1:19:30 PM
Ty Parker & Son, Inc.ͲSubmitted 11/30/21 at 2:14:55 PM US Fire Equipment, LLCͲSubmitted 11/30/21 at 9:12:36 AM Ward Apparatus, LLCͲSubmitted 11/29/21 at 4:19:07 PM
The Proposals were opened electronically, and a list of all Proposers was made publicly available in the Sourcewell Procurement Portal, on November 30, 2021, at 4:32:09 PM CT. All responsive proposals were then submitted for review by the Sourcewell Evaluation Committee. ___________________________________________________________________________ James Voelker, CPCM, CFCM, Procurement Lead AnalystCarol Jackson, Procurement Analyst 





 

 


EXHIBIT 1 627
RFP #113021

REQUEST FOR PROPOSALS
for
Firefighting Apparatus and Fire Service Vehicles
Proposal Due Date: November 30, 2021, 4:30 p.m., Central Time Sourcewell, a State of Minnesota local government unit and service cooperative, is requesting proposals for Firefighting Apparatus and Fire Service Vehicles to result in a contracting solution for use by its Participating Entities. Sourcewell Participating Entities include thousands of governmental, higher education, K-12 education, nonprofit, tribal government, and other public agencies located in the United States and Canada. A full copy of the Request for Proposals can be found on the Sourcewell Procurement Portal [https://proportal.sourcewell-mn.gov]. Only proposals submitted through the Sourcewell Procurement Portal will be considered. Proposals are due no later than November 30, 2021, at 4:30 p.m. Central Time, and late proposals will not be considered.

Solicitation Schedule
Public Notice of RFP Published: October 12, 2021
Pre-proposal Conference: November 2, 2021, 10:00 a.m., Central Time Question Submission Deadline: November 19, 2021, 4:30 p.m., Central Time Proposal Due Date: November 30, 2021, 4:30 p.m., Central Time Late responses will not be considered.

Opening: November 30, 2021, 6:30 p.m., Central Time
See RFP Section V.G. “Opening”
EXHIBIT 1 628
I. ABOUT SOURCEWELL
A. SOURCEWELL

Sourcewell is a State of Minnesota local government unit and service cooperative created under the laws of the State of Minnesota (Minnesota Statutes Section 123A.21) that facilitates a competitive public solicitation and contract award process for the benefit of its 50,000+ participating entities across the United States and Canada. Sourcewell’s solicitation process complies with State of Minnesota law and policies, conforms to Canadian trade agreements, and results in cooperative purchasing solutions from which Sourcewell’s Participating Entities procure equipment, products, and services.

Cooperative purchasing provides participating entities and suppliers increased administrative efficiencies and the power of combined purchasing volume that result in overall cost savings. At times, Sourcewell also partners with other purchasing cooperatives to combine the purchasing volume of their membership into a single solicitation and contract expanding the reach of contracted suppliers’ potential pool of end users.

Sourcewell uses a website-based platform, the Sourcewell Procurement Portal, through which all proposals to this RFP must be submitted.

B. USE OF RESULTING CONTRACTS
In the United States, Sourcewell’s contracts are available for use by:
• Federal and state government entities1;
• Cities, towns, and counties/parishes;
• Education service cooperatives;
• K-12 and higher education entities;
• Tribal government entities;
• Some nonprofit entities; and
• Other public entities.

In Canada, Sourcewell’s contracts are available for use by:
• Provincial and territorial government departments, ministries, agencies, boards, councils, committees, commissions, and similar agencies; • Regional, local, district, and other forms of municipal government, municipal organizations, school boards, and publicly-funded academic, health, and social service entities referred to as MASH sector (this should be construed to include but not be 1 Pursuant to HAR §3-128-2, the State of Hawaii, Department of Accounting and General Services, State Procurement Office, on behalf of the State of Hawaii and participating jurisdictions, has provided notice of its Intent to Participate in the solicitation as a participating entity.

EXHIBIT 1 629
limited to the Cities of Calgary, Edmonton, Toronto, Ottawa, and Winnipeg), as well as any corporation or entity owned or controlled by one or more of the preceding entities; • Crown corporations, government enterprises, and other entities that are owned or controlled by these entities through ownership interest; • Members of the Rural Municipalities of Alberta (RMA) and their represented Associations: MASH (municipalities, academic institutions, schools and hospitals) and MUSH (municipalities, universities, schools and hospitals) sectors, and other governmental agencies eligible to use the Sourcewell contracts. MASH and MUSH sector refers to regional, local, district or other forms of municipal government, school boards, publicly-funded academic, health and social service entities, as well as any corporation or entity owned or controlled by one or more of the preceding entities, including but not limited to represented associations, Saskatchewan Association of Rural Municipalities ("SARM"), Association of Manitoba Municipalities ("AMM"), Local Authorities Services/Association of Municipalities Ontario ("LAS/AMO", excluding the cities of Toronto and Ottawa), Nova Scotia Federation of Municipalities (“NSFM”), Federation of Prince Edward Island Municipalities (“FPEIM”), Municipalities Newfoundland Labrador (“MNL”), Union of New Brunswick Municipalities (“UNBM”), North West Territories Association of Communities ("NWTAC") and their members.

RMA Participants may include all not-for-profit agencies for Canadian provinces and territories.

For a listing of current United States and Canadian Participating Entities visit Sourcewell’s website (note: there is a tab for each country): https://www.sourcewell-mn.gov/sourcewell-forvendors/agency-locator.

Participating Entities typically access contracted equipment, products, or services through a purchase order issued directly to the contracted supplier. A Participating Entity may request additional terms or conditions related to a purchase. Use of Sourcewell contracts is voluntary and Participating Entities retain the right to obtain similar equipment, products, or services from other sources.

To meet Participating Entities’ needs, Sourcewell broadly publishes public notice of all solicitation opportunities, including this RFP. In the United States each state-level procurement department receives notice for possible re-posting.

Proof of publication will be available at the conclusion of the solicitation process.

EXHIBIT 1 630
II. SOLICITATION DETAILS
A. SOLUTIONS-BASED SOLICITATION
This RFP and contract award process is a solutions-based solicitation; meaning that Sourcewell is seeking equipment, products, or services that meet the general requirements of the scope of this RFP and that are commonly desired or are required by law or industry standards.

B. REQUESTED EQUIPMENT, PRODUCTS, OR SERVICES
It is expected that proposers will offer a wide array of equipment, products, or services at lower prices and with better value than what they would ordinarily offer to a single government entity, a school district, or a regional cooperative.

1. Sourcewell is seeking proposals for Firefighting Apparatus and Fire Service Vehicles, including:
a. New, remount, or refurbished:
i. Firefighting apparatus and service vehicles, of all types, such as: pumper/engine, initial attack, mobile water supply, aerial, quint, special service, mobile foam, command and communications, and purpose-built firefighting or rescue trailers; ii. Wildland fire apparatus, of all types, such as: fire suppression equipment, mobile water supply, and crew carriers; and,
iii. Aircraft rescue and firefighting vehicles.
b. Purpose-built chassis and vehicle components for firefighting apparatus and fire service vehicles;
c. Equipment, options, accessories, and supplies complementary or incidental to the purchase of a turnkey or complete unit of the types described in Sections 1. a. i. – iii. above.
d. Services related to the offering of the solutions described in Sections 1. a. - c. above, including installation, customization, remount, refurbishment, inspection, repair, maintenance, training, and support.

2. This solicitation does not include those equipment, products, or services covered under categories included in contracts currently maintained by Sourcewell:
a. Health & Safety, Medical, Surgical, and First Aid Related Equipment, Supplies, Accessories, and Services (RFP #061417);
b. Trailers with Related Equipment, Accessories, and Services (RFP #121918), with the limited exception of the purpose-built firefighting or rescue trailers identified in Section

1. a. i. above;
c. Firefighting Personal Protective Equipment, Apparel, and Accessories, with Related Cleaning and Maintenance Equipment (RFP #032620);
EXHIBIT 1 631
d. Firefighting Equipment and Rescue Tools with Related Supplies and Accessories (RFP #040220), with the limited exception of the equipment, options, accessories, and supplies identified in Section 1. c. above;
e. Class 4-8 Chassis with Related Equipment, Accessories, and Services (RFP #060920), with the limited exception of the purpose-built chassis identified in Section 1. b. above; f. Public Safety Communications Technology and Hardware Solutions (RFP #042021); g. Automobiles, SUVs, Vans, and Light Trucks with Related Equipment and Accessories (RFP #091521); and,
h. Ambulance and Emergency Medical Service Vehicles (RFP #110921).

Generally, the solutions for Participating Entities are turn-key solutions, providing a combination of equipment, products and services, delivery, and installation to a properly operating status. However, equipment or products only solutions may be appropriate for situations where Participating Entities possess the ability, either in-house or through local thirdparty contractors, to properly install and bring to operation the equipment or products being proposed.

Sourcewell prefers suppliers that provide a sole source of responsibility for the equipment, products, and services provided under a resulting contract. If proposer is including the equipment, products, and services of its subsidiary entities, the proposer must also identify all included subsidiaries in its proposal. If proposer requires the use of distributors, dealers, resellers, or subcontractors to provide the equipment, products, or services, the proposal must address how the equipment, products or services will be provided to Participating Entities, and describe the network of distributors, dealers, resellers, and/or subcontractors that will be available to serve Participating Entities under a resulting contract.

Sourcewell desires the broadest possible selection of equipment, products, and services being proposed over the largest possible geographic area and to the largest possible cross-section of Sourcewell current and future Participating Entities.

C. REQUIREMENTS
It is expected that proposers have knowledge of all applicable industry standards, laws, and regulations and possess an ability to market and distribute the equipment, products, or services to Participating Entities.

1. Safety Requirements. All items proposed must comply with current applicable safety or regulatory standards or codes.

2. Deviation from Industry Standard. Deviations from industry standards must be identified with an explanation of how the equipment, products, and services will provide equivalent function, coverage, performance, and/or related services.

EXHIBIT 1 632

3. New Equipment and Products. Proposed equipment and products must be for new, current model; however, proposer may offer certain close-out equipment or products if it is specifically noted in the Pricing proposal.

4. Delivered and operational. Unless clearly noted in the proposal, equipment and products must be delivered to the Participating Entity as operational.

5. Warranty. All equipment, products, supplies, and services must be covered by a warranty that is the industry standard or better.

D. ANTICIPATED CONTRACT TERM
Sourcewell anticipates that the term of any resulting contract(s) will be four years, with an optional one-year extension that may be offered based on the best interests of Sourcewell and its Participating Entities.

E. ESTIMATED CONTRACT VALUE AND USAGE
Based on past volume of similar contracts, the estimated annual value of all transactions from contracts resulting from this RFP are anticipated to be USD $200 Million; therefore, proposers are expected to propose volume pricing. Sourcewell anticipates considerable activity under the contract(s) awarded from this RFP; however, sales and sales volume from any resulting contract are not guaranteed.

F. MARKETING PLAN
Proposer’s sales force will be the primary source of communication with Participating Entities.

The proposer’s Marketing Plan should demonstrate proposer’s ability to deploy a sales force or dealer network to Participating Entities, as well as proposer’s sales and service capabilities. It is expected that proposer will promote and market any contract award.

G. ADDITIONAL CONSIDERATIONS

1. Contracts will be awarded to proposers able to best meet the need of Participating Entities. Proposers should submit their complete line of equipment, products, or services that are applicable to the scope of this RFP.

2. Proposers should include all relevant information in its proposal, since Sourcewell cannot consider information that is not included in the proposal. Sourcewell reserves the right to verify proposer’s information and may request clarification from a proposer, including samples of the proposed equipment or products.

3. Depending upon the responses received in a given category, Sourcewell may need to organize responses into subcategories in order to provide the broadest coverage of the requested equipment, products, or services to Participating Entities. Awards may be based on a subcategory.

EXHIBIT 1 633

4. A proposer’s documented negative past performance with Sourcewell or its Participating Entities occurring under a previously awarded Sourcewell contract may be considered in the evaluation of a proposal.

III. PRICING
A. REQUIREMENTS
All proposed pricing must be:

1. Either Line-Item Pricing or Percentage Discount from Catalog Pricing, or a combination of these:
a. Line-item Pricing is pricing based on each individual product or services. Each line must indicate the proposer’s published “List Price,” as well as the “Contract Price.” b. Percentage Discount from Catalog or Category is based on a percentage discount from a catalog or list price, defined as a published Manufacturer’s Suggested Retail Price (MSRP) for the products or services. Individualized percentage discounts can be applied to any number of defined product groupings. Proposers will be responsible for providing and maintaining current published MSRP with Sourcewell, and this pricing must be included in its proposal and provided throughout the term of any Contract resulting from this RFP.

2. The proposer’s not to exceed price. A not to exceed price is the highest price for which equipment, products, or services may be billed to a Participating Entity. However, it is permissible for suppliers to sell at a price that is lower than the contracted price.

3. Stated in U.S. and Canadian dollars (as applicable).

4. Clearly understandable, complete, and fully describe the total cost of acquisition (e.g., the cost of the proposed equipment, products, and services delivered and operational for its intended purpose in the Participating Entity’s location).

Proposers should clearly identify any costs that are NOT included in the proposed product or service pricing. This may include items such as installation, set up, mandatory training, or initial inspection. Include identification of any parties that impose such costs and their relationship to the proposer. Additionally, proposers should clearly describe any unique distribution and/or delivery methods or options offered in the proposal.

B. ADMINISTRATIVE FEES
Proposers are expected to pay to Sourcewell an administrative fee in exchange for Sourcewell facilitating the resulting contracts. The administrative fee is normally calculated as a percentage of the total sales to Participating Entitiesfor all contracted equipment, products, or services made during a calendar quarter, and is typically one percent (1%) to two percent (2%). In some categories, a flat fee may be an acceptable alternative.

EXHIBIT 1 634
IV. CONTRACT
Proposers awarded a contract will be required to execute a contract with Sourcewell (see attached template). Only those modifications the proposer indicates in its proposal will be available for discussion. Much of the language in the Contract reflects Minnesota legal requirements and cannot be altered. Numerous and/or onerous exceptions that contradict Minnesota law may result in the proposal being disqualified from further review and evaluation.

To request a modification to the template Contract, a proposer must submit the Exceptions to Terms, Conditions, or Specifications table with its proposal. Only those exceptions noted at the time of the proposal submission will be considered.

Exceptions must:

1. Clearly identify the affected article and section.

2. Clearly note the requested modification; and as applicable, provide requested alternative language.

Unclear requests will be automatically denied.

Only those exceptions that have been accepted by Sourcewell will be included in the contract document provided to the awarded supplier for signature.

If a proposer receives a contract award resulting from this solicitation it will have up to 30 days to sign and return the contract. After that time, at Sourcewell’s sole discretion, the contract award may be revoked.

V. RFP PROCESS
A. PRE-PROPOSAL CONFERENCE
Sourcewell will hold an optional, non-mandatory pre-proposal conference via webcast on the date and time noted in the Solicitation Schedule for this RFP and on the Sourcewell Procurement Portal. The purpose of this conference is to allow potential proposers to ask questions regarding this RFP and Sourcewell’s competitive contracting process. Information about the webcast will be sent to all entities that have registered for this solicitation opportunity through their Sourcewell Procurement Portal Supplier Account. Pre-proposal conference attendance is optional.

B. QUESTIONS REGARDING THIS RFP AND ORAL COMMUNICATION
All questions regarding this RFP must be submitted through the Sourcewell Procurement Portal.

The deadline for submission of questions is found in the Solicitation Schedule and on the Sourcewell Procurement Portal. Answers to questions will be issued through an addendum to EXHIBIT 1 635
this RFP. Repetitive questions will be summarized into a single answer and identifying information will be removed from the submitted questions.

All questions, whether specific to a proposer or generally related to the RFP, must be submitted using this process. Do not contact individual Sourcewell staff to ask questions or request information as this may disqualify the proposer from responding to this RFP. Sourcewell will not respond to questions submitted after the deadline.

C. ADDENDA
Sourcewell may modify this RFP at any time prior to the proposal due date by issuing an addendum. Addenda issued by Sourcewell become a part of the RFP and will be delivered to potential proposers through the Sourcewell Procurement Portal. Sourcewell accepts no liability in connection with the delivery of any addenda.

Before a proposal will be accepted through the Sourcewell Procurement Portal, all addenda, if any, must be acknowledged by the proposer by checking the box for each addendum. It is the responsibility of the proposer to check for any addenda that may have been issued up to the solicitation due date and time.

If an addendum is issued after a proposer submitted its proposal, the Sourcewell Procurement Portal will WITHDRAW the submission and change the proposer’s proposal status to INCOMPLETE. The proposer can view this status change in the “MY BIDS” section of the Sourcewell Procurement Portal Supplier Account. The proposer is solely responsible to check the “MY BIDS” section of the Sourcewell Procurement Portal Supplier Account periodically after submitting its proposal (and up to the Proposal Due Date). If the proposer’s proposal status has changed to INCOMPLETE, the proposer is solely responsible to:
i) make any required adjustments to its proposal;
ii) acknowledge the addenda; and
iii) ensure the re-submitted proposal is received through the Sourcewell Procurement Portal no later than the Proposal Due Date and time shown in the Solicitation Schedule above.

D. PROPOSAL SUBMISSION
Proposer’s complete proposal must be submitted through the Sourcewell Procurement Portal no later than the date and time specified in the Solicitation Schedule. Any other form of proposal submission, whether electronic, paper, or otherwise, will not be considered by Sourcewell. Late proposals will not be considered. It is the proposer’s sole responsibility to ensure that the proposal is received on time.

It is recommended that proposers allow sufficient time to upload the proposal and to resolve any issues that may arise. The time and date that a proposal is received by Sourcewell is solely determined by the Sourcewell Procurement Portal web clock.

EXHIBIT 1 636
In the event of problems with the Sourcewell Procurement Portal, follow the instructions for technical support posted in the portal. It may take up to 24 hours to respond to certain issues.

Upon successful submission of a proposal, the Sourcewell Procurement Portal will automatically generate a confirmation email to the proposer. If the proposer does not receive a confirmation email, contact Sourcewell’s support provider at [email protected].

To ensure receipt of the latest information and updates via email regarding this solicitation, or if the proposer has obtained this solicitation document from a third party, the onus is on the proposer to create a Sourcewell Procurement Portal Supplier Account and register for this solicitation opportunity.

Within the Sourcewell Procurement Portal, all proposals must be digitally acknowledged by an authorized representative of the proposer attesting that the information contained in in the proposal is true and accurate. By submitting a proposal, proposer warrants that the information provided is true, correct, and reliable for purposes of evaluation for potential contract award.

The submission of inaccurate, misleading, or false information is grounds for disqualification from a contract award and may subject the proposer to remedies available by law.

E. GENERAL PROPOSAL REQUIREMENTS
Proposals must be:
• In substantial compliance with the requirements of this RFP or it will be considered nonresponsive and be rejected.
• Complete. A proposal will be rejected if it is conditional or incomplete. • Submitted in English.
• Valid and irrevocable for 90 days following the Proposal Due Date.

Any and all costs incurred in responding to this RFP will be borne by the proposer.

F. PROPOSAL WITHDRAWAL
Prior to the proposal deadline, a proposer may withdraw its proposal.

G. OPENING
The Opening of proposals will be conducted electronically through the Sourcewell Procurement Portal. A list of all proposers will be made publicly available in the Sourcewell Procurement Portal after the Proposal Due Date, but no later than the Opening time listed in the Solicitation Schedule.

EXHIBIT 1 637
To view the list of proposers, verify that the Sourcewell Procurement Portal opportunities list search is set to “All” or “Closed.” The solicitation status will automatically change to “Closed” after the Proposal Due Date and Time.

VI. EVALUATION AND AWARD
A. EVALUATION
It is the intent of Sourcewell to award one or more contracts to responsive and responsible proposers offering the best overall quality, selection of equipment, products, and services, and price that meet the commonly requested specifications of Sourcewell and its Participating Entities. The award(s) will be limited to the number of proposers that Sourcewell determines is necessary to meet the needs of its Participating Entities. Factors to be considered in determining the number of contracts to be awarded in any category may include the following:
• The number of and geographic location of:
o Proposers necessary to offer a comprehensive selection of equipment, products, or services for Participating Entities’ use.
o A proposer’s sales and service network to assure availability of product supply and coverage to meet Participating Entities’ anticipated needs. • Total evaluation scores.
• The attributes of proposers, and their equipment, products, or services, to assist Participating Entities achieve environmental and social requirements, preferences, and goals.

Information submitted as part of a proposal should be as specific as possible when responding to the RFP. Do not assume Sourcewell has any knowledge about a specific supplier or product.

B. AWARD(S)
Award(s) will be made to the proposer(s) whose proposal conforms to all conditions and requirements of the RFP, and consistent with the award criteria defined in this RFP.

Sourcewell may request written clarification of a proposal at any time during the evaluation process.

Proposal evaluation will be based on the following scoring criteria and the Sourcewell Evaluator Scoring Guide (a copy is available in the Sourcewell Procurement Portal):

Conformance to RFP Requirements 50
Financial Viability and Marketplace Success 75
Ability to Sell and Deliver Service 100
Marketing Plan 50
Value Added Attributes 75
EXHIBIT 1 638
Warranty 50
Depth and Breadth of Offered Equipment, Products, or Services 200 Pricing 400
TOTAL POINTS 1000
C. PROTESTS OF AWARDS
Any protest made under this RFP by a proposer must be in writing, addressed to Sourcewell’s Executive Director, and delivered to the Sourcewell office located at 202 12th Street NE, P.O.

Box 219, Staples, MN 56479. All documents that comprise the complete protest package must be received no later than 10 calendar days’ following Sourcewell’s notice of contract award(s) or non-award and must be time stamped by Sourcewell no later than 4:30 p.m., Central Time. A protest must allege a procedural, technical, or legal defect, with supporting documentation. A protest that merely requests a re-evaluation of a proposal’s content will not be entertained A protest must include the following items:
• The name, address, and telephone number of the protester; • Identification of the solicitation by RFP number;
• A precise statement of the relevant facts;
• Identification of the alleged procedural, technical, or legal defect; • Analysis of the basis for the protest;
• Any additional supporting documentation;
• The original signature of the protester or its representative; and • Protest bond in the amount of $20,000 (except where prohibited by law or treaty).

Protests that do not address these elements will not be reviewed.

D. RIGHTS RESERVED
This RFP does not commit Sourcewell to award any contract, and a proposal may be rejected if it is nonresponsive, conditional, incomplete, conflicting, or misleading. Proposals that contain false statements or do not support an attribute or condition stated by the proposer may be rejected.

Sourcewell reserves the right to:
• Modify or cancel this RFP at any time;
• Reject any and all proposals received;
• Reject proposals that do not comply with the provisions of this RFP; • Select, for contracts or for discussion, a proposal other than that with the lowest cost; • Independently verify any information provided in a proposal; • Disqualify any proposer that does not meet the requirements of this RFP, is debarred or suspended by the United States or Canada, State of Minnesota, Participating Entity’s EXHIBIT 1 639
state or province; has an officer, or other key personnel, who have been charged with a serious crime; or is bankrupt, insolvent, or where bankruptcy or insolvency are a reasonable prospect;
• Waive or modify any informalities, irregularities, or inconsistencies in the proposals received;
• Clarify any part of a proposal and discuss any aspect of the proposal with any proposer; and negotiate with more than one proposer;
• Award a contract if only one responsive proposal is received if it is in the best interest of Participating Entities; and
• Award a contract to one or more proposers if it is in the best interest of Participating Entities.

E. DISPOSITION OF PROPOSALS
All materials submitted in response to this RFP will become property of Sourcewell and will become public record in accordance with Minnesota Statutes Section 13.591, after negotiations are complete. Sourcewell considers that negotiations are complete upon execution of a resulting contract. It is the proposer’s responsibility to clearly identify any data submitted that it considers to be protected. Proposer must also include a justification for the classification citing the applicable Minnesota law. Sourcewell may reject proposals that are marked confidential or nonpublic, either substantially or in their entirety.

Sourcewell will not consider the prices submitted by the proposer to be confidential, proprietary, or trade secret materials. Financial information, including financial statements, provided by a proposer is not considered trade secret under the statutory definition.

EXHIBIT 1 640
10/20/2021
Addendum No. 1
Solicitation Number: RFP 113021
Solicitation Name: Firefighting Apparatus and Fire Service Vehicles Consider the following Question and Answer to be part of the above-titled solicitation documents. The remainder of the documents remain unchanged.

Question 1:

Is the PDF in the zipped file on the bid details page supposed to be editable? Answer 1:

No, the file is not designed for edits by a proposer. Refer to RFP Section IV. – Contract, for additional detail related to the Sourcewell template contract posted to the bid details page for this solicitation.

End of Addendum
Acknowledgement of this Addendum to RFP 113021 posted to the Sourcewell Procurement Portal on 10/20/2021 is required at the time of proposal submittal.

EXHIBIT 1 641
10/29/2021
Addendum No. 2
Solicitation Number: RFP 113021
Solicitation Name: Firefighting Apparatus and Fire Service Vehicles Consider the following Question and Answer to be part of the above-titled solicitation documents. The remainder of the documents remain unchanged.

Question 1:

Are we required to have a vehicle dealer license in the state of Minnesota in order to be an awarded supplier?
Answer 1:

It is left to the discretion of each proposer to determine the licensures and supporting documentation necessary to best demonstrate their ability to serve Sourcewell and Sourcewell participating entities and to satisfy all requirements included in the RFP, contract template, and the Sourcewell Procurement Portal questionnaire tables.

End of Addendum
Acknowledgement of this Addendum to RFP 113021 posted to the Sourcewell Procurement Portal on 10/29/2021, is required at the time of proposal submittal.

EXHIBIT 1 642
11/11/2021
Addendum No. 3
Solicitation Number: RFP 113021
Solicitation Name: Firefighting Apparatus and Fire Service Vehicles Consider the following Question and Answer to be part of the above-titled solicitation documents. The remainder of the documents remain unchanged.

Question 1:

In regard to the administrative fee, what percentage amount is assessed on each opportunity to be paid to Sourcewell? Or is it a one-time fee per acquisition? Answer 1:

Refer to RFP Section III. B. – Administrative Fees, for directions on proposing an administrative fee. It is left to the discretion of each proposer to determine and propose an administrative fee that is consistent with its business and its industry.

End of Addendum
Acknowledgement of this Addendum to RFP 113021 posted to the Sourcewell Procurement Portal on 11/11/2021, is required at the time of proposal submittal.

EXHIBIT 1 643
11/20/2021
Addendum No. 4
Solicitation Number: RFP 113021
Solicitation Name: Firefighting Apparatus and Fire Service Vehicles Consider the following Questions and Answers to be part of the above-titled solicitation documents. The remainder of the documents remain unchanged.

Question 1:

The RFP states Sourcewell is seeking proposals for new, remount or refurbished. Is Sourcewell looking for us to acknowledge we offer remount or refurb or are we expected to provide pricing?
Answer 1:

In the competitive process, Sourcewell will not advise a proposer on the content of the proposal. It is left to the discretion of each proposer to determine how to best articulate its offering of equipment, products, and services, propose the pricing approach that aligns with its business methods, and satisfy all requirements of the RFP.

Question 2:

Line items #1 - 3 of the Portal questionnaire tables address legal entity and subsidiary or assumed names. Clarify whether the subsidiary names will be the brand visible to the participating entity for an awarded supplier.

Answer 2:

Determinations related to the identification of an awarded supplier’s contract on the Sourcewell website, and in related communications to participating entities, will be made after the competitive process is complete in consultation with an awarded supplier.

EXHIBIT 1 644
Question 3:

Section 18 Insurance - Network Security and Privacy Liability Insurance – The entity under this response has had to provide cyber liability what is the significance to this requirement?
Answer 3:

Refer to RFP Section IV. – Contract for additional detail related to the Sourcewell template contract. An awarded vendor will be expected to carry the insurance coverages as stated in the contract upon execution. A request for modification to the Sourcewell contract template may only be submitted with a proposal. To request a modification to the template Contract terms, conditions, or specifications, a proposer must complete and submit the Exceptions to Terms, Conditions, or Specifications table, which is found as the final Table of Step 1 in the proposal submission process within the Sourcewell Procurement Portal.

Question 4:

Section D Waiver of Subrogation- How does this apply to this RFP? Answer 4:

Refer to Answer 3 above.

Question 5:

Is delivery required to be included in pricing or are we able to provide pricing and state that delivery is not included.

Answer 5:

Refer to Answer 1 above.

Question 6:

Section 2B of the template contract states that Supplier warrants all Equipment, Products and Services. Is it required or is it an option to include service? If service is not included in pricing is additional information necessary? Answer 6:

Refer to Answer 1 above.

EXHIBIT 1 645
Question 7:

Template contract section 3. A. - Shipping and Shipping Cost – states that a Supplier must arrange for and pay for the return shipment on equipment and products that arrive in a defective or inoperable condition. Would this incorporate supplier or subcontractor?
Answer 7:

In the competitive process, Sourcewell will not advise a proposer on the content of the proposal. It is left to the discretion of each proposer to determine how to best articulate its ability to serve Sourcewell participating entities.

Question 8:

Line Item 24 in questionnaire table 5 includes a request for size of transaction? What is this referring to is this a unit quantity?
Answer 8:

It is left to the discretion of each proposer to determine the information necessary to best demonstrate their marketplace success and satisfy all the requirements included in the questionnaire tables.

Question 9:

Is an Entity/Subsidiary allowed to list a product on Sourcewell product list that is sold and distributed by the Entity/Subsidiary, but is produced by a contract manufacturer? Answer 9:

The Sourcewell RFP is an open and competitive solicitation process. A proposer is allowed to propose the entire line of equipment, products, and services falling within the requested equipment, products, or services of the subject solicitation. Proposals are evaluated based on the criteria stated in the RFP.

Question 10:

In Table 11, because of some supplier’s difficulties to confirm pricing, can we list a product and confirm the price only after the awarding?
EXHIBIT 1 646
Answer 10:

It is left to the discretion of each proposer to determine and propose the pricing approach that aligns with its business methods and satisfies all the requirements of RFP Article III - Pricing. Proposals are evaluated based on the criteria stated in the RFP.

Question 11:

If a supplier is successful with this RFP, the contract would be between the supplier and Sourcewell. If the supplier as an independent dealer network, do the Participating Entities have the obligations to contract with the supplier or can they contract directly with the dealer which in turn the dealer contract with the supplier? Answer 11:

Refer to RFP Section II. B. – Requested Equipment, Products, or Services – “… If proposer requires the use of distributors, dealers, resellers, or subcontractors to provide the equipment, products, or services, the proposal must address how the equipment, products or services will be provided to Participating Entities, and describe the network of distributors, dealers, resellers, and/or subcontractors that will be available to serve Participating Entities under a resulting contract.”
Question 12:

Does the contract allow a line-item surcharge vs as part of the quote vs having it included in publish base pricing? Surcharges can fluctuate so looking to understand if there will be flexibility with the new contract.

Answer 12:

Refer to Answer 10 above.

Question 13:

Can a vendor be awarded contracts from different Sourcewell RFPs? Answer 13:

Each Sourcewell opportunity represents a separate and distinct open and competitive solicitation. The outcome of an earlier solicitation, including a contract award, has no bearing on the evaluation of a proposer’s subsequent proposal.

Question 14:

In regards to table 2, item 11: If financial statements are provided to Sourcewell for the proposal do those statements in turn become public knowledge? EXHIBIT 1 647
Answer 14:

Refer to RFP Section VI. E. – Disposition of Proposals related to the treatment of materials submitted in response to the RFP.

Question 15:

Pricing is very volatile currently with component shortages. Pricing for each model and options offered within our current quoting system could significantly fluctuate by the time this proposal is reviewed. Would offering a percentage off our current quoting MSRP be acceptable with a few examples at the time of this bid? Answer 15:

Refer to Answer 10 above.

End of Addendum
Acknowledgement of this Addendum to RFP 113021 posted to the Sourcewell Procurement Portal on 11/20/2021, is required at the time of proposal submittal.

EXHIBIT 1 648

EXHIBIT B

INSURANCE REQUIREMENTS

NOT APPLICABLE
EXHIBIT 1 649

EXHIBIT C

PAGE INTENTIONALLY LEFT BLANK
EXHIBIT 1 650
August 20, 2022
Mr. Brandon Doolan, Operations Chief
City of Stockton Fire Department
400 E. Main Street
Stockton, CA 95202
Dear Chief Doolan:

I am enclosing our proposal for one (1) new Pierce Manufacturing Inc. 1500 GPM Pumper. Based on your department’s input, we have selected the Pierce Enforcer chassis on which to base this proposal. Some of the noteworthy features you will find include:
 450 horsepower Cummins L9 motor with an Allison EVS 3000 transmission  1,500 GPM Waterous single stage pump with 700-gallon water tank  Pierce Husky 3 single agent foam system with refill and draft features  All emergency lighting is LED
The cost of the unit described in this proposal is contingent upon the city making a 100% prepayment (or entering into a lease purchase agreement) at time of contract signing. Lease purchase options are available upon request (a lease purchase option would allow the district to take advantage of the 100% pre-payment pricing).

The total price shown includes California Sales Tax at the rate of 9.00% and includes one (1) factory inspection trip as outlined in the specification. Price is based on delivery F.O.B. to the City of Stockton Fire Department at the address shown above.

If the city elects to purchase the proposed apparatus and would like to sign a contract, please let me know right away and I will have one drafted and send it to you for signing. Or if the city prefers to purchase the proposed apparatus with a Purchase Order (PO), please address it to the following:

Golden State Fire Apparatus Inc.
7400 Reese Road
Sacramento, CA 95828
This quote will be valid until September 30, 2022.

We appreciate the opportunity to submit this information and look forward to going over any questions you might have. Let me know if there is anything else I can do and feel free to give me a call anytime. My cell number is (209) 613-3809 and thank you again.

Sincerely,
Ryan Wright
President
EXHIBIT 1 651

PRODUCT

PROPOSAL
Exhibit “A”
Bid #716
EXHIBIT 1 652

PROPOSAL PREPARED FOR
City of Stockton Fire Department
Pierce Manufacturing, Inc.

Enforcer 1500 GPM Pumper
Sourcewell contract #113021-PMI,
ID #259
August 8, 2022

SALES CONSULTANT
Ryan Wright
Golden State Fire Apparatus, Inc.
7400 Reese Road
Sacramento, CA 95828
209.613.3809 Cell
[email protected]

PARTS, SERVICE & SUPPORT
Golden State Emergency Vehicle Service, Inc.
7400 Reese Road
Sacramento, CA 95828
916.330.1638 Office
[email protected]
EXHIBIT 1 653
PROPOSAL PREPARED FOR:

City of Stockton Fire Department
400 E. Main Street
Stockton, CA 95202
We hereby propose and agree to furnish, after your acceptance of this proposal and the proper execution by the CITY OF STOCKTON, hereinafter called “Customer” and an officer of Golden State Fire Apparatus, Inc., hereinafter called “GSFA”, the following fire apparatus and equipment, hereinafter called “Product”:

PROPOSAL SUMMARY
This proposal includes the following items in accordance with the specifications hereto attached:
 Fire apparatus and equipment described herein
 Delivery to GSFA service center in Sacramento
 Pre-delivery inspection/services by GSFA
 Final delivery from service center to Customer
 Demonstration and familiarization of the Product

PRODUCT COMPLETION
Product shall be built in accordance with the specifications hereto attached, delays due to acts of God, strikes, war, or intentional conflict, failures to obtain chassis, materials, unusual weather conditions or other causes beyond GSFA’s control not preventing, within approximately 495 to 525 CALENDAR DAYS after receipt of this order and the acceptance thereof at our Sacramento, California office. Within thirty (30) calendar days after receipt of this order and acceptance thereof, GSFA shall submit to Customer a production schedule including tentative pre-construction conference, final inspection and final delivery dates.

DELIVERY LOCATION
Product shall be shipped in accordance with the specifications hereto attached and be delivered to you at STOCKTON, CALIFORNIA. Proof of insurance must be demonstrated by the Customer to GSFA prior to transferring of the Product(s).

Submitted Date: August 8, 2022
Proposal Number: 90808-22
Expiration
Date:

September 30,
2022
Sales Consultant: Ryan Wright
# Description Unit Price
A One (1) Pierce Manufacturing, Inc. Enforcer 1500 GPM Pumper 773,346.39 B Discount for Sourcewell contract #113021-PMI, ID #259 (36,272.00) C Pre-Payment Discount for 100% Payment at Time of Order (24,789.44) SUBTOTAL 712,284.95

9.00% State Sales Tax 64,105.65
California Tire Fee 10.50
GRAND TOTAL 776,401.10
EXHIBIT 1 654

ACCEPTING THIS PROPOSAL
In the event Customer wishes to purchase the Product described in this Proposal and the attached specifications, then, prior to the expiration date listed on page 2 of this Proposal, Customer shall sign and return this Proposal. Thereafter, GSFA and Customer will endeavor to enter into a purchase agreement incorporating this Proposal and including additional terms (a “Purchase Agreement”). If Customer returns a signed copy of this Proposal alone, GSFA will send Customer its form of Purchase Agreement for Customer’s review and signature. If Customer desires to use its standard form of purchase order as the Purchase Agreement, then Customer should return a signed copy of this Proposal along with a copy of such purchase order. All purchase orders shall be made out to GSFA. GSFA will review such purchase order and contact the Customer regarding any required revisions. Only upon a full execution of a Purchase Agreement shall GSFA and Customer be obligated to purchase and sell the Product set forth in this Proposal.

TERMS AND CONDITIONS
The following Terms and Conditions are hereby made part of this Proposal:

1. Payment Terms (100% Pre-Payment at Time of Order) –
Customer shall pay the amount listed on page one of this Proposal, which includes: (i) the total price for the Product (the “Purchase Price”), (ii) the estimated state sales tax on the Product, and (iii) the California tire fee (together with the Purchase Price and estimated state sales tax, the “Grand Total”) within fifteen (15) calendar days from the date on which the Purchase Agreement is fully executed. The proposed delivery timeframe for the Product, which is outlined on page one of this Proposal, shall not begin until full payment of the Grand Total is received. In the event Customer does not pay GSFA the Grand Total in the timeframe set forth in this Section 1, GSFA may, in its sole discretion, cancel the Purchase Agreement entered into between the parties.

2. Multiple Unit Purchase – If the Purchase Price includes pricing for multiple units, the price stated on this Proposal shall only be valid if the quantity of Products being proposed are purchased at the same time, pursuant to the same Purchase Agreement.

3. Stock / Demo Units – If applicable, any stock/demo units, including those identified by this Proposal, are available for sale on an as-is, first-come and first served-basis. Regardless of this Proposal, the first Customer to enter into a Purchase Agreement identifying any such stock/demo unites shall obtain said units.

4. Order Changes – The Customer may request that GSFA
incorporate a change to the Product or the Specifications for the Product by delivering a written change order to GSFA, which shall include a description of the proposed change sufficient to permit GSFA to evaluate the feasibility of such change (a “Change Order”). GSFA will provide Customer a written response (a “Response”) stating (i) whether GSFA will accommodate such Change Order (which GSFA may decide in its sole and absolute discretion) and (ii) the terms of the modification to the order, including any increase or decrease in the Purchase Price resulting from such Change Order, and any effect on production
scheduling or Delivery resulting from such Change Order.

Customer shall have seven (7) days after receipt of the Response to notify GSFA as to whether Customer desires to make the changes GSFA has approved in the Response. In the event Customer counter-signs GSFA’s Response, Customer shall pay the increase (or be refunded the decrease) in the Purchase Price prior to final delivery to Customer location.

5. Force Majeure – GSFA shall not be responsible nor deemed to be in default on account of delays in performance due to causes which are beyond GSFA’s and manufacturer’s control and which make GSFA’s performance impracticable, including but not limited to wars, insurrections, strikes, riots, fires, storms, floods, other acts of nature, explosions, earthquakes, accidents, any act of government, delays in transportation, inability to obtain necessary labor supplies or manufacturing facilities, allocation regulations or orders affecting materials, equipment, facilities or completed products, failure to obtain any required license or certificates, acts of God or the public enemy or terrorism, failure of transportation, epidemics, quarantine restrictions, failure of vendors (due to causes similar to those within the scope of this clause) to perform their contracts or labor troubles causing cessation, slowdown, or interruption of work.

6. Cancellation/Termination – In the event Customer and GSFA enter into a Purchase Agreement and Customer thereafter cancels or terminates the Purchase Agreement, GSFA will charge a cancellation fee as follows: (a) 10% of the Purchase Price after order is accepted and entered by GSFA; (b) 20% of the Purchase Price after completion of the pre-construction phase of the order process; and (c) 50% of the Purchase Price after the requisition of any materials or commencement of any manufacturing or assembly of the Product by either GSFA or the manufacturer of the Product. The tier of cancellation fee applicable to any cancellation shall be in the sole and absolute discretion of GSFA.

7. State Sales Tax – Customer shall be responsible for the cost of state sales tax associated with, or attributable to the Product.

The taxes owed by Customer for the Product is subject to adjustment for the applicable state sales tax rate in effect when the Product is delivered to the Customer. Therefore, the sales tax will be increased or decreased at the time of delivery if a change in the sales tax rate has occurred, in which case Customer shall pay GSFA (or be refunded by GSFA) the applicable change in sales tax.

8. Proposal Expiration – After the Expiration Date shown on page one of this Proposal, Customer shall require GSFA’s written consent to accept this Proposal.

9. Governing Law – This Proposal is to be governed by and under the laws of the state of California.

Thank you for providing Golden State Fire Apparatus, Inc. with the opportunity to provide this proposal. If you have any questions regarding the options presented or need additional options, please contact me.

Sincerely, I, _______________________________________________________________authorized representative of CITY OF STOCKTON agrees to purchase the proposed Product(s) and agree to the terms and conditions of this proposal and the specifications hereto attached.

Ryan Wright SIGNATURE: __________________________________________________________________________ Golden State Fire Apparatus, Inc.

TITLE: _________________________________________________ DATE: ____________________ EXHIBIT 1 655

PRODUCT

SPECIFICATIONS
Exhibit “B”
Bid #716
EXHIBIT 1 656
Proposal Details Report
OptionCode Type Option ProposalText
0766611 Boiler Plates, Pumper Golden State Fire Apparatus Inc is pleased to submit a proposal to Stockton Fire Department for a Pierce® triple combination pumper per your request for quotation. The following paragraphs will describe in detail the apparatus, construction methods, and equipment proposed. This proposal will indicate size, type, model and make of components parts and equipment, providing proof of compliance with each and every item (except where noted) in the departments advertised specifications.

PIERCE MANUFACTURING was founded in 1913. Since then we have been building bodies with one philosophy, "BUILD THE FINEST". Our skilled craftsmen take pride in their work, which is reflected, in the final product. We have been building fire apparatus since the early "forties" giving Pierce Manufacturing over 75 years of experience in the fire apparatus market. Pierce Manufacturing has built and put into service more than 62,500 apparatus, including more than 33,900 on Pierce custom chassis designed and built specifically for fire and emergency applications. Our Appleton, Wisconsin facility has over 870,000 total square feet of floor space situated on approximately 105 acres of land. Our Bradenton, Florida facility has 300,000 square feet of floor space situated on approximately 38 acres of land.

Our beliefs in high ethical standards are carried through in all of our commitments and to everyone with whom we do business. Honesty, Integrity, Accountability and Citizenship are global tenets by which we all live and work. Consequently, we neither engage in, nor have we ever been convicted of price fixing, bid rigging, or collusion in any domestic or international fire apparatus market.

Pierce has only one brand of fire apparatus "Pierce", ensuring you are receiving top of the line product that meets your specification.

In accordance with the current edition of NFPA 1901 standards, this proposal will specify whether the fire department, manufacturer, or apparatus dealership will provide required loose equipment.

Images and illustrative material in this proposal are as accurate as known at the time of publication, but are subject to change without notice. Images and illustrative material is for reference only, and may include optional equipment and accessories and may not include all standard equipment.

GENERAL DESIGN AND CONSTRUCTION
To control quality, ensure compatibility, and provide a single source for service and warranty, the custom cab, chassis, pump module and body will be entirely designed, assembled/welded and painted in Pierce owned manufacturing facilities. This includes, but not limited to the cab weldment, the pumphouse module assembly, the chassis assembly, the body and the electrical system.

QUALITY AND WORKMANSHIP
Pierce has set the pace for quality and workmanship in the fire apparatus field. Our tradition of building the highest quality units with craftsmen second to none has been the rule right from the beginning and we demonstrate that ongoing commitment by: Ensuring all steel welding follows American Welding Society D1.1-2004 recommendations for structural steel welding. All aluminum welding follows American Welding society and ANSI D1.2-2003 requirements for structural welding of aluminum. All sheet metal welding follows American welding Society B2.1-2000 requirements for structural welding of sheet metal. Our flux core arc welding uses alloy rods, type 7000 and is performed to American Welding Society standards A5.20-E70T1. Furthermore, all employees classified as welders are tested and certified to meet the American welding Society codes upon hire and every three (3) years thereafter. Pierce also employs and American Welding Society certified welding inspector in plant during working hours to monitor weld quality.

Pierce Manufacturing operates a Quality Management System under the requirements of ISO 9001. These standards sponsored by the International Organization for Standardization (ISO) specify the quality systems that are established by the manufacturer for design, manufacture, installation and service. A copy of the certificate of compliance is included with this proposal.

In addition to the Quality Management system, we also employ a Quality Achievement Supplier program to insure the vendors and suppliers that we utilize meet the high standards we demand.

That is just part of our overall "Quality at the Source" program at Pierce.

To demonstrate the quality of our products and services, a list of at least twenty five (25) fire departments/municipalities that have purchased vehicles for a second time is provided.

DELIVERY
The apparatus will be delivered under its own power to insure proper break-in of all components while the apparatus is still under warranty. A qualified delivery representative shall deliver the apparatus and remain for a sufficient length of time to instruct personnel in proper operation, care and maintenance of the equipment delivered.

MANUAL AND SERVICE INFORMATION
At time of delivery, complete operation and maintenance manuals covering the apparatus will be provided. A permanent plate will be mounted in the driver's compartment specifying the quantity and type of fluids required including engine oil, engine coolant, transmission, pump transmission lubrication, pump primer and drive axle.

SAFETY VIDEO
At the time of delivery Pierce will also provide one (1) 39-minute, professionally produced apparatus safety video, in DVD format. This video will address key safety considerations for personnel to follow when they are driving, operating, and maintaining the apparatus, including the following: vehicle pre-trip inspection, chassis operation, pump operation, aerial operation, and safety during maintenance.

PERFORMANCE TESTS
A road test will be conducted with the apparatus fully loaded and a continuous run of no less than ten (10) miles. During that time the apparatus will show no loss of power nor will it overheat. The 8/8/2022
Customer: Stockton FD Bid Number: 716
Representative Wright, Ryan Job Number:

Requirements Manager: Organization: Golden State Fire Apparatus, Inc Description: Stockton FD (38685 DUPLICAT
Chassis: Enforcer Chassis
Body: Pumper, Medium, Aluminum, 2nd Gen
Bid #: 716 1
EXHIBIT 1 657
transmission drive shaft or shafts and the axles will run quietly and be free of abnormal vibration or noise. The apparatus when fully loaded will not have less than 25 percent nor more than 50 percent on the front axle, and not less than 50 percent nor more than 75 percent on the rear axle.

The apparatus will meet NFPA 1901 acceleration and braking requirements.

SERVICE AND WARRANTY SUPPORT
Pierce dealership support will be provided by Golden State Emergency Vehicle Service Inc by operating a Pierce authorized service center. The service center will have factory-trained mechanics on staff versed in Pierce fire apparatus. The service facility will be located within fifty (50) miles of the fire department.

In addition to the dealership, Pierce has service facilities located in both, Weyauwega, Wisconsin and Bradenton, Florida. Pierce also maintains a dedicated parts facility of over 100,000 square feet in Appleton, Wisconsin. The parts facility stocks in excess of $5,000,000 in parts dedicated to service and replacement parts. The parts facility employs a staff dedicated solely for the distribution and shipment of service and replacement parts.

Service parts for the apparatus being proposed can be found via Pierceparts.com which, is an interactive online tool that delivers information regarding your specific apparatus as well as the opportunity to register for training classes.

As a Pierce customer you have the ability to view the complete bill of materials for your specific apparatus, including assembly drawings, piece part drawings, and beneficial parts notations. You will also have the ability to search the complete Pierce item master through a parts search function which offers all Pierce SKU's and descriptions offered on all Pierce apparatus. Published component catalogs, which include proprietary systems along with an extensive operators manual library is available for easy reference.

Pierce Manufacturing maintains a dedicated service and warranty staff of over 35 personnel, dedicated to customer support, which also maintains a 24 hour 7 day a week toll free hot line, four (4) on staff EVTs, and offers hands-on repair and maintenance training classes multiple times a year.

LIABILITY
The successful bidder will defend any and all suits and assume all liability for the use of any patented process including any device or article forming a part of the apparatus or any appliance furnished under the contract.

INSURANCE PROVIDED BY BIDDER

COMMERCIAL GENERAL LIABILITY INSURANCE
The successful bidder will, during the performance of the contract and for three (3) years following acceptance of the product, keep in force at least the following minimum limits of commercial general liability insurance:

Each Occurrence $1,000,000
Products/Completed Operations Aggregate $1,000,000
Personal and Advertising Injury $1,000,000
General Aggregate $2,000,000
Coverage will be written on a Commercial General Liability form. The policy will be written on an occurrence form and will include Contractual Liability coverage for bodily injury and property damage subject to the terms and conditions of the policy.

The policy will include Owner as an additional insured when required by written contract.

COMMERCIAL AUTOMOBILE LIABILITY INSURANCE
The successful bidder will, during the performance of the contract, keep in force at least the following minimum limits of commercial automobile liability insurance and coverage will be written on a Commercial Automobile liability form:

Each Accident Combined Single Limit: $1,000,000

UMBRELLA/EXCESS LIABILITY INSURANCE
The successful bidder will, during the performance of the contract and for three (3) years following acceptance of the product, keep in force at least the following minimum limits of umbrella liability insurance:

Aggregate: $3,000,000
Each Occurrence: $3,000,000
The umbrella policy will be written on an occurrence basis and at a minimum provide excess to the bidder's General Liability and Automobile Liability policies.

The required limits can be provided by one (1) or more policies provided all other insurance requirements are met.

Coverage will be provided by a carrier(s) rated A- or better by A.M. Best.

All policies will provide a 30-day notice of cancellation to the named insured. The Certificate of Insurance will provide the following cancellation clause: Should any of the above described polices be cancelled before the expiration date thereof, notice will be delivered in accordance with the policy provisions.

Bidder agrees to furnish owner with a current Certificate of Insurance with the coverages listed above along with the bid. The certificate will show the purchaser as certificate holder.

INSURANCE PROVIDED BY MANUFACTURER

PRODUCT LIABILITY INSURANCE
The manufacturer will, during the performance of the contract and for three (3) years following acceptance of the product, keep in force at least the following minimum limits of Product Liability insurance:

Each Occurrence $1,000,000
Products/Completed Operations Aggregate $1,000,000
Coverage will be written on a Commercial General Liability form. The policy will be written on an occurrence form. The manufacturer's policy will include the owner as additional insured when required by written contract between the Owner and a Pierce authorized dealer.

UMBRELLA/EXCESS LIABILITY INSURANCE
The manufacturer will, during the performance of the contract and for three (3) years following acceptance of the product, keep in force at least the following minimum limits of umbrella liability insurance:

Bid #: 716 2
EXHIBIT 1 658
Each Occurrence: $25,000,000
Aggregate: $25,000,000
The umbrella policy will be written on an occurrence basis and provide excess to the manufacturer's General Liability/Products policies.

The required limits can be provided by one (1) or more policies provided all other insurance requirements are met.

Coverage will be provided by a carrier(s) rated A- or better by A.M. Best.

All policies will provide a 30-day notice of cancellation to the named insured. The Certificate of Insurance will provide the following cancellation clause: Should any of the above described polices be cancelled before the expiration date thereof, notice will be delivered in accordance with the policy provisions.

Manufacturer agrees to furnish owner with a current Certificate of Insurance with the coverages listed above along with the bid. The certificate will show the purchaser as the certificate holder.
0661794 Single Source Compliance SINGLE SOURCE MANUFACTURER Pierce Manufacturing, Inc. provides an integrated approach to the design and manufacture of our products that delivers superior apparatus and a dedicated support team. From our facilities, the chassis, cab weldment, cab, pumphouse (including the sheet metal enclosure, valve controls, piping and operators panel) and body will be entirely designed, tested, and hand assembled to the customer's exact specifications. The electrical system either hardwired or multiplexed, will be both designed and integrated by Pierce Manufacturing. The warranties relative to these major components (excluding component warranties such as engine, transmission, axles, pump, etc.) will be provided by Pierce as a single source manufacturer. Pierce's single source solution adds value by providing a fully engineered product that offers durability, reliability, maintainability, performance, and a high level of quality.
0584456 Manufacture Location, Appleton,
Wisconsin
Your apparatus will be manufactured in Appleton, Wisconsin. 0584452 RFP Location: Appleton, Wisconsin
0588609 Vehicle Destination, US
0788859 SP Fast Track Template Truck SPECIAL INSTRUCTIONS 475 / 16 SP's at time of booking
0610784 Comply NFPA 1901 Changes
Effective Jan 1, 2016, With
Exceptions
NFPA 2016 STANDARDS
This unit will comply with the NFPA standards effective January 1, 2016, except for fire department directed exceptions. These exceptions will be set forth in the Statement of Exceptions.

Certification of slip resistance of all stepping, standing and walking surfaces will be supplied with delivery of the apparatus.

All horizontal surfaces designated as a standing or walking surface that are greater than 48.00" above the ground must be defined by a 1.00" wide line along its outside perimeter. Perimeter markings and designated access paths to destination points will be identified on the customer approval print and are shown as approximate. Actual location(s) will be determined based on materials used and actual conditions at final build. Access paths may pass through hose storage areas and opening or removal of covers or restraints may be required. Access paths may require the operation of devices and equipment such as the aerial device or ladder rack.

A plate that is highly visible to the driver while seated will be provided. This plate will show the overall height, length, and gross vehicle weight rating.

The manufacturer will have programs in place for training, proficiency testing and performance for any staff involved with certifications.

An official of the company will designate, in writing, who is qualified to witness and certify test results.
0533347 Pumper/Pumper with Aerial Device
Fire Apparatus
0588611 Vehicle Certification, Pumper
Bid #: 716 3
EXHIBIT 1 659
0661778 Agency, Apparatus Certification,
Pumper/Tanker, U.L.

NFPA COMPLIANCY
Apparatus proposed by the bidder will meet the applicable requirements of the National Fire Protection Association (NFPA) as stated in current edition at time of contract execution. Fire department's specifications that differ from NFPA specifications will be indicated in the proposal as "non-NFPA".

PUMP TEST
Underwriters Laboratory (UL) will test, approved, and certify the pump. The test results and the pump manufacturer's certification of hydrostatic test; the engine manufacturer's certified brake horsepower curve; and the pump manufacturer's record of pump construction details will be forwarded to the Fire Department.

GENERATOR TEST
If the unit has a generator, Underwriters Laboratory (UL) will test, approved, and certify the generator. The test results will be provided to the Fire Department at the time of delivery.

BREATHING AIR TEST
If the unit has breathing air, Pierce Manufacturing will draw an air sample from the air system and have the sample certified that the air quality meets the requirements of NFPA 1989, Standard on Breathing Air Quality for Fire and Emergency Services Respiratory Protection. 0891947 Certification, Vehicle Inspection
Program, NFPA 1901

VEHICLE INSPECTION PROGRAM CERTIFICATION
To assure the vehicle is built to current NFPA 1901 standards, the apparatus, in its entirety, will be third-party, independent, audit-certified through Underwriters Laboratory (UL) that it is built and complies to all applicable standards in the current edition. The certification includes: all design, production, operational, and performance testing of not only the apparatus, but those components that are installed on the apparatus.

A placard will be affixed in the driver's side area stating the third party agency, the date, the standard and the certificate number of the whole vehicle audit. 0000000 STF GSFA, Final Insp, ATW Factory,
Premium Airport, 3 Days and 2 nights

FINAL INSPECTION FACTORY TRIP
A final inspection trip to the manufacturing facility will be provided for four (4) Customer representative(s). The intent of this trip is to ensure that the apparatus is built to specification and to detect any deficiencies that require correction. The final inspection trip will have a duration of three (3) days and two (2) nights and be scheduled at times mutually agreed upon between Golden State Fire Apparatus (GSFA). and the Customer. Costs for airfare, lodging, meals and ground transportation while at the manufacturers location will be the responsibility of GSFA. Air travel will be from one of the following airports: Oakland, Redding, Eureka, Fresno or Reno.

Costs such as Customer ground transportation in California, Customer airport parking, Customer luggage fees and Customer incidentals while traveling to the factory will be the responsibility of the Customer. Flight reservations are non-refundable and in the event of a cancellation after booking, the Customer will be responsible for all costs associated with this cancellation, which may include not only the original ticket cost but also any change or cancellation fees imposed by the airline and/ or travel agency. Flight reservations are also non-transferable. 0799172 FLEET CUSTOMER
0766110 Consortium, Sourcewell
0537375 Unit of Measure, US Gallons
0030006 Bid Bond Not Requested BID BOND NOT REQUESTED
A bid bond will not be included. If requested, the following will apply:

All bidders will provide a bid bond as security for the bid in the form of a 5% bid bond to accompany their bid. This bid bond will be issued by a Surety Company who is listed on the U.S.

Treasury Departments list of acceptable sureties as published in Department Circular 570. The bid bond will be issued by an authorized representative of the Surety Company and will be accompanied by a certified power of attorney dated on or before the date of bid. The bid bond will include language, which assures that the bidder/principal will give a bond or bonds as may be specified in the bidding or contract documents, with good and sufficient surety for the faithful performance of the contract, including the Basic One (1) Year Limited Warranty, and for the prompt payment of labor and material furnished in the prosecution of the contract.

Notwithstanding any document or assertion to the contrary, any surety bond related to the sale of a vehicle will apply only to the Basic One (1) Year Limited Warranty for such vehicle. Any surety bond related to the sale of a vehicle will not apply to any other warranties that are included within this bid (OEM or otherwise) or to the warranties (if any) of any third party of any part, component, attachment or accessory that is incorporated into or attached to the vehicle. In the event of any contradiction or inconsistency between this provision and any other document or assertion, this provision will prevail.

Bid #: 716 4
EXHIBIT 1 660
0582800 Performance Bond, 100% with 25%
Warranty Bond, 1 Yr, and Payment
Bond
PERFORMANCE BOND, 1 YEAR
The successful bidder will furnish a Performance and Payment bond (Bond) equal to 100 percent of the total contract amount within 30 days of the notice of award. Such Bond will be in a form acceptable to the Owner and issued by a surety company included within the Department of Treasury's Listing of Approved Sureties (Department Circular 570) with a minimum A.M. Best Financial Strength Rating of A and Size Category of XV. In the event of a bond issued by a surety of a lesser Size Category, a minimum Financial Strength rating of A+ is required.

Bidder and Bidder's surety agree that the Bond issued hereunder, whether expressly stated or not, also includes the surety's guarantee of the vehicle manufacturer's Basic One (1) Year Limited Warranty period included within this proposal. Owner agrees that the penal amount of this bond will be simultaneously amended to 25 percent of the total contract amount upon satisfactory acceptance and delivery of the vehicle(s) included herein. Notwithstanding anything contained within this contract to the contrary, the surety's liability for any warranties of any type will not exceed one (1) year from the date of such satisfactory acceptance and delivery, or the actual Basic One (1) Year Limited Warranty period, whichever is shorter. 0000007 Approval Drawing APPROVAL DRAWING
A drawing of the proposed apparatus will be prepared and provided to the purchaser for approval before construction begins. The Pierce sales representative will also be provided with a copy of the same drawing. The finalized and approved drawing will become part of the contract documents. This drawing will indicate the chassis make and model, location of the lights, siren, horns, compartments, major components, etc.

A "revised" approval drawing of the apparatus will be prepared and submitted by Pierce to the purchaser showing any changes made to the approval drawing. 0002928 Electrical Diagrams ELECTRICAL WIRING DIAGRAMS
Two (2) electrical wiring diagrams, prepared for the model of chassis and body, will be provided. 0649754 Enforcer Chassis ENFORCER CHASSIS
The Pierce Enforcer™ is the custom chassis developed exclusively for the fire service. Chassis provided will be a new, tilt-type custom fire apparatus. The chassis will be manufactured in the apparatus body builder's facility eliminating any split responsibility. The chassis will be designed and manufactured for heavy-duty service, with adequate strength, capacity for the intended load to be sustained, and the type of service required. The chassis will be the manufacturer's first line tilt cab.
0523786 Angle of Approach ANGLE OF APPROACH
The angle of approach will be 10 degrees degrees. This will be effective with the truck in a loaded state.
0523787 Angle of Departure ANGLE OF DEPARTURE
The angle of departure will be 10 degrees degrees. This will be effective with the truck in a loaded state.
0000110 Wheelbase WHEELBASE
The wheelbase of the vehicle will be 193.50".
0000070 GVW Rating GVW RATING
The gross vehicle weight rating will be 42,000 lbs.
0649713 Frame Rails, 10.25" x 3.50" x .375",
Saber FR/Enf
FRAME
The chassis frame will be built with two (2) steel channels bolted to five (5) cross members or more, depending on other options of the apparatus. The side rails will be heat-treated steel measuring 10.25" x 3.50" x 0.375".

Each rail will have a section modulus of 16.00 cubic inches, yield strength of 120,000 psi, and a resisting bending moment (rbm) of 1,921,069 inch-pounds. 0648354 Frame Liner, Internal "C", 9.38" x

3.13" x .25", Saber FR/Enf, 26" Qval

FRAME REINFORCEMENT
A full-length mainframe "C" liner will be provided.

The liner will be an internal "C" design, heat-treated steel measuring 9.38" x 3.13" x 0.25". Each reinforcement member will have a section modulus of 3.90 cubic inches, yield strength of 120,000 psi and resisting bending moment (rbm) of 938,762 in-lb. 0637708 Axle, Front, Meritor FL-941, 18,000
lb, Saber FR/Enforcer

FRONT AXLE
The front axle will be a reverse "I" beam type with inclined king pins. It will be a Meritor™ axle, Model FL-941, with a rated capacity of 18,000 lb.

Bid #: 716 5
EXHIBIT 1 661
0637879 Suspension, Front, Standens, Taper
Leaf, 18,000 lb, Saber FR/Enforcer

FRONT SUSPENSION
The front springs will be a Standens, three (3)-leaf, taper leaf design, 54.00" long x 4.00" wide, with a ground rating of 18,000 lb.

The two (2) top leaves will wrap the forward spring hanger pin. The top leaf will also wrap the rear spring hanger pin. Both the front and rear eyes will be Berlin style wraps that will place the eyes in the horizontal plane within the main leaf. This will reduce bending stress from acceleration and braking.

A steel encased rubber bushing will be used in the spring eye. The steel encased rubber bushing will be maintenance free and require no lubrication.
0000321 Shock Absorbers on Front Axle,
Monroe Magnum 65, Saber/Enforcer

SHOCK ABSORBERS
To provide a smoother ride, the front axle will be furnished with heavy-duty telescoping shock absorbers.
0000322 Oil Seals, Front Axle FRONT OIL SEALS
Oil seals with viewing window will be provided on the front axle. 0771369 Tires, Front, Michelin, X WORKS Z,
315/80R22.50, LRL, Fire Service
Speed Rating

FRONT TIRES
Front tires will be Michelin 315/80R22.50 radials, load range L, X® WORKS™ Z, rated for 18,180 lb maximum axle load and 75 mph maximum speed.
0019575 Wheels, Front, Alcoa, 22.50" x 9.00",
Aluminum, Hub Pilot
The tires will be mounted on Alcoa 22.50" x 9.00" polished aluminum disc wheels with a ten (10) stud, 11.25" bolt circle.
0530458 Axle, Rear, Meritor RS24-160, 24,000
lb, Saber/Enforcer

REAR AXLE
The rear axle will be a Meritor™, Model RS-24-160, with a capacity of 24,000 lb. 0544253 Top Speed of Vehicle, 68 MPH TOP SPEED OF VEHICLE A rear axle ratio will be furnished to allow the vehicle to reach a top speed of 68 mph. 0555350 Suspen, Rear, Hendrickson FMX 242
EX, Air Ride, 24,000 lb

REAR SUSPENSION
Rear suspension will be a Hendrickson FMX 242 EX, air ride with a ground rating of 24,000 lb.

The suspension will have the following features:
- Heavy-duty shock absorbers to protect air springs from overextension - Heavy-duty torque rods and bushings
- Premium, heavy-duty rubber bushings require no lubrication - Integrated stabilizer design results in greater stability - Low spring rate air springs for excellent ride quality - Dual height control valves to maintain level vehicle from side to side 0000485 Oil Seals, Rear Axle REAR OIL SEALS
Oil seals will be provided on the rear axle(s).
0539392 Plug, Rear Axle Drain, Magnetic REAR AXLE DRAIN PLUG The rear axle drain plug will be magnetic.
0031836 Tires, Rear, Michelin, XZE*,
12R22.50, 16 ply, Single

REAR TIRES
Rear tires will be four (4) Michelin 12R22.50 radials, 16 ply "all position" XZE* tread, rated for 27,120 lb maximum axle load and 75 mph maximum speed.
0019625 Wheels, Rear, Alcoa, 22.50" x 8.25",
Aluminum, Hub Pilot, Single
The tires will be mounted on Alcoa 22.50" x 8.25" polished aluminum disc wheels with a ten (10) stud 11.25" bolt circle.
0568081 Tire Balancing, Counteract Beads TIRE BALANCE
All tires will be balanced with Counteract balancing beads. The beads will be inserted into the tire and eliminate the need for wheel weights.
0620570 Tire Pressure Monitoring,
RealWheels, AirSecure, Valve Cap,
Single Axle

TIRE PRESSURE MANAGEMENT
There will be a RealWheels LED AirSecure™ tire alert pressure management system provided, that will monitor each tire's pressure. A sensor will be provided on the valve stem of each tire for a total of six (6) tires.

The sensor will calibrate to the tire pressure when installed on the valve stem for pressures between 10 and 200 psi. The sensor will activate an integral battery operated LED when the pressure of that tire drops 5 to 8 psi.

Removing the cap from the sensor will indicate the functionality of the sensor and battery. If the sensor and battery are in working condition, the LED will immediately start to flash.

Bid #: 716 6
EXHIBIT 1 662
0003245 Axle Hub Covers w/center hole, S/S,
Front Axle

FRONT HUB COVERS
Stainless steel hub covers will be provided on the front axle. An oil level viewing window will be provided.
0001960 Axle Hub Covers, Rear, S/S, High
Hat (Pair)

REAR HUB COVERS
A pair of stainless steel high hat hub covers will be provided on rear axle hubs. 0052332 Covers, Lug Nut, Stainless Steel LUG NUT COVERS Stainless steel lug nut covers will be installed on all lug nuts. 0002046 Mud Flap, Front and Rear, No Logo MUD FLAPS
Mud flaps will be installed behind the front and rear wheels. The mud flaps will be black. 0646362 Chocks, Wheel, Worden HWGY- SB,
Super Gripper

WHEEL CHOCKS
There will be one (1) pair of Worden Safety Products, Model HWGY-SB, wheel chocks provided.

Heavy Duty, large molded aluminum wheel chock with solid bottom, yellow powder coat finish. 0544690 Mounting Brackets, Chocks, Provided
by Fire Department
Wheel Chock Brackets Provided by Fire Department
The wheel chock brackets are not on the apparatus as manufactured. The fire department will provide and install the wheel chock brackets.
0010670 ABS Wabco Brake System, Single
rear axle

ANTI-LOCK BRAKE SYSTEM
The vehicle will be equipped with a Meritor WABCO 4S4M, anti-lock braking system. The ABS will provide a 4-channel anti-lock braking control on both the front and rear wheels. A digitally controlled system that utilizes microprocessor technology will control the anti-lock braking system.

Each wheel will be monitored by the system. When any particular wheel begins to lockup, a signal will be sent to the control unit. This control unit then will reduce the braking of that wheel for a fraction of a second and then reapply the brake. This anti-lock brake system will eliminate the lockup of any wheel thus helping to prevent the apparatus from skidding out of control. 0508676 Brakes, Meritor, EX225, 17", Disc
Plus, Front
BRAKES
The service brake system will be full air type by Meritor™.

Front brakes will be Model EX225 Disc Plus, disc type with automatic pad wear adjustment and

17.00" ventilated rotors for improved stopping distance. 0000730 Brakes, Meritor, Cam, Rear, 16.50 x

7.00"
The rear brakes will be Meritor™ 16.50" x 7.00" cam operated with automatic slack adjusters.

Dust shields will be provided.
0020784 Air Compressor, Brake,
Cummins/Wabco 18.7 CFM

BRAKE SYSTEM AIR COMPRESSOR
The air compressor will be a Cummins/WABCO with 18.7 cubic feet per minute output. 0644232 Brake Reservoirs, 4,272 Cubic Inch
Minimum Capacity, Saber
FR/Enforcer

BRAKE SYSTEM
The brake system will include:

Brake treadle valve
Heated automatic moisture ejector on air dryer
Total air system minimum capacity of 4,272 cubic inches Two (2) air pressure gauges with a red warning light and an audible alarm, that activates when air pressure falls below 60 psi
Spring set parking brake system
Parking brake operated by a push-pull style control valve A parking "brake on" indicator light on instrument panel Park brake relay/inversion and anti-compounding valve, in conjunction with a double check valve system, with an automatic spring brake application at 40 psi A pressure protection valve to prevent all air operated accessories from drawing air from the air system when the system pressure drops below 80 psi (550 kPa) 1/4 turn drain valves on each air tank
The air tank will be primed and painted to meet a minimum 750 hour salt spray test.

To reduce the effects of corrosion, the air tank will be mounted with stainless steel brackets. 0568012 Air Dryer, Wabco System Saver
1200, Heater, 2010

BRAKE SYSTEM AIR DRYER
The air dryer will be WABCO System Saver 1200 with spin-on coalescing filter cartridge and 100 watt heater.
0000790 Brake Lines, Nylon BRAKE LINES
Color-coded nylon brake lines will be provided. The lines will be wrapped in a heat protective loom in the chassis areas that are subject to excessive heat.

Bid #: 716 7
EXHIBIT 1 663
0020851 Not Required, Air Inlet

0014130 Air Tank, Additional for Extra Air Horn
Capacity

ADDITIONAL AIR TANK FOR AIR HORN
An additional air tank with 1,454 cubic inch displacement will be provided to increase the capacity of the air system. This tank will be dedicated for air horn use.

The air tank will be primed and painted to meet a minimum 750 hour salt spray test. To reduce the effects of corrosion, the air tank will be mounted with stainless steel brackets.

The output flow of the engine air compressor varies with engine rpm. Full compressor output is only achieved at governed engine speed. Engine speed may be limited by generators, pumps and other PTO driven options.
0630460 Moisture Ejector, Manual, Remote
Mounted, Enforcer/Saber FR

MANUAL MOISTURE EJECTOR(S)
Manual moisture ejectors for a single axle pumper reservoir capacity will be installed in the brake system.

The moisture ejector(s) will be remote mounted on the left side of vehicle, as close to the edge of vehicle as possible.

A loop will be provided at the moisture ejector, to allow for ease of pulling the drain.

Each moisture ejector will have a label directly under the ejector, stating air tank drain.

Nylon tubing, 0.38" diameter, will be routed from the air tank to the moisture ejector. The nylon tubing will be covered with protective split loom.

The moisture ejector(s) will be provided on the under the LS3 compartment (one for "wet tank", one for "primary tank". one for "secondary tank", and one for "air horn tank") reservoir(s). 0736437 Engine, Cummins L9, 450 hp, 1250
lb-ft, W/OBD, EPA 2021, Saber
FR/Enforcer
ENGINE
The chassis will be powered by an electronically controlled engine as described below:

Make:

Cummins
Model:

L9
Power:
450 hp at 2100 rpm
Torque:
1250 lb-ft at 1400 rpm
Governed Speed:
2200 rpm
Emissions Level:

EPA 2021
Fuel:

Diesel
Cylinders:

Six (6)
Displacement:
543 cubic inches (8.9L)
Starter:

Delco 39MT™
Fuel Filters:

Spin-on style primary filter with water separator and water-in-fuel sensor. Secondary spin-on style filter.

The engine will include On-board diagnostics (OBD), which provides self diagnostic and reporting. The system will give the owner or repair technician access to state of health information for various vehicle sub systems. The system will monitor vehicle systems, engine and after treatment. The system will illuminate a malfunction indicator light on the dash console if a problem is detected.
0001244 High Idle w/Electronic Engine,
Custom

HIGH IDLE
A high idle switch will be provided, inside the cab, on the instrument panel, that will automatically maintain a preset engine rpm. A switch will be installed, at the cab instrument panel, for activation/deactivation.

The high idle will be operational only when the parking brake is on and the truck transmission is in neutral. A green indicator light will be provided, adjacent to the switch. The light will illuminate when the above conditions are met. The light will be labeled "OK to Engage High Idle." 0687994 Engine Brake, Jacobs Compression
Brake, Cummins Engine

ENGINE BRAKE
A Jacobs® engine brake is to be installed with the controls located on the instrument panel within easy reach of the driver.

The driver will be able to turn the engine brake system on/off and have a high, medium and low setting.

The engine brake will activate when the system is on and the throttle is released.

The high setting of the brake application will activate and work simultaneously with the variable geometry turbo (VGT) provided on the engine.

The engine brake will be installed in such a manner that when the engine brake is slowing the vehicle the brake lights are activated.

The ABS system will automatically disengage the auxiliary braking device, when required. 0644227 Clutch, Fan, Air Actuated, Saber
FR/Enforcer

CLUTCH FAN
A fan clutch will be provided. The fan clutch will be automatic when the pump transmission is in "Road" position, and constantly engaged when in "Pump" position.

Bid #: 716 8
EXHIBIT 1 664
0644573 Air Intake, Water & Ember Screen,
Saber FR/Enforcer

ENGINE AIR INTAKE
The engine air intake will be located above the engine cooling package. It will draw fresh air from the front of the apparatus through the radiator grille.

The ember separator is designed to prevent road dirt and recirculating hot air from entering the engine.

The ember separator will be easily accessible by tilting the cab. 0794761 Exhaust System, 4", 2017 L9 Engine,
Horizontal, Right Side

EXHAUST SYSTEM
The exhaust system will be stainless steel from the turbo to the engine's aftertreatment device, and will be 4.00" in diameter. The exhaust system will include a single module aftertreatment device to meet current EPA standards. An insulation wrap will be provided on all exhaust pipes between the turbo and aftertreatment device to minimize the heat loss to the aftertreatment device . The exhaust will terminate horizontally ahead of the right side rear wheels. A tailpipe diffuser will be provided to reduce the temperature of the exhaust as it exits. Heat deflector shields will be provided to isolate chassis and body components from the heat of the tailpipe diffuser.
0788765 Radiator, Saber FR/Enforcer RADIATOR
The radiator and the complete cooling system will meet or exceed NFPA and engine manufacturer cooling system standards.

For maximum corrosion resistance and cooling performance, the entire radiator core will be constructed using long life aluminum alloy. The radiator core will consist of aluminum fins, having a serpentine design, brazed to aluminum tubes.

The radiator core will have a minimum front area of 1060 square inches.

Supply tank will be made of heavy duty glass-reinforced nylon and the return tank will be mode of aluminum. Both tanks will be crimped onto the core assembly using header tabs and a compression gasket to complete the radiator core assembly. There will be a full steel frame around the inserts to enhance cooling system durability and reliability.

The radiator will be compatible with commercial antifreeze solutions.

The radiator assembly will be isolated from the chassis frame rails with rubber isolators to prevent the development of leaks caused by twisting or straining when the apparatus operates over uneven terrain.

The radiator will include a de-aeration/expansion tank. For visual coolant level inspection, the radiator will have a built-in sight glass. The radiator will be equipped with a 15 psi pressure relief cap.

A drain port will be located at the lowest point of the cooling system and/or the bottom of the radiator to permit complete flushing of the coolant from the system.

Shields or baffles will be provided to prevent recirculation of hot air to the inlet side of the radiator. 0001090 Cooling Hoses, Rubber COOLANT LINES
Gates, or Goodyear, rubber hose will be used for all engine coolant lines installed by Pierce Manufacturing.

Hose clamps will be stainless steel constant torque type to prevent coolant leakage. They will expand and contract according to coolant system temperature thereby keeping a constant clamping pressure on the hose.
0021126 Fuel Tank, 50 Gallon, Left Side Fill FUEL TANK
A 50 gallon fuel tank will be provided and mounted at the rear of the chassis. The tank will be constructed of 12-gauge, hot rolled steel. It will be equipped with swash partitions and a vent. To eliminate the effects of corrosion, the fuel tank will be mounted with stainless steel straps.

A .75" drain plug will be located in a low point of the tank for drainage.

A fill inlet will be located on the left hand side of the body and is covered with a hinged, spring loaded, stainless steel door that is marked "Ultra Low Sulfur - Diesel Fuel Only".

A .50" diameter vent will be installed from tank top to just below fuel fill inlet.

The fuel tank will meet all FHWA 393.67 requirements including a fill capacity of 95 percent of tank volume.
0001129 Lines, Fuel All fuel lines will be provided as recommended by the engine manufacturer. 0723696 DEF Tank, 8.0 Gallon, LS Fill, Rear of
Rear Axle, Triple Door

DIESEL EXHAUST FLUID TANK
An 8.0 gallon diesel exhaust fluid (DEF) tank will be provided and mounted in the driver's side body rearward of the rear axle.

A 0.50" drain plug will be provided in a low point of the tank for drainage.

A fill inlet will be provided and marked "Diesel Exhaust Fluid Only". The fill inlet will be located adjacent to the engine fuel inlet behind a triple, brushed stainless steel door on the left side of the vehicle. The fuel door will be held closed by flush lift and turn latch.

The tank will meet the engine manufacturers requirement for 10 percent expansion space in the event of tank freezing.

The tank will include an integrated heater unit that utilizes engine coolant to thaw the DEF in the event of freezing.
0723716 Fuel Priming Pump, Electronic,
Automatic, Cummins, No Swt Req'd

FUEL PRIMING PUMP
A Cummins automatic electronic fuel priming pump will be integrated as part of the engine.

Bid #: 716 9
EXHIBIT 1 665
0552607 Shutoff Valves (2), Fuel Line @ Filter

FUEL SHUTOFF
A shutoff valve will be installed in the fuel line, on both sides of the fuel filter. 0553019 Cooler, Engine Fuel, Imp/Vel,
AXT/Qtm/Sab/DCF/SFR/Enf

FUEL COOLER
An air to fuel cooler will be installed in the engine fuel return line. 0645743 Fuel/Water Separator, Racor
690R1210, 10 Micron, Heater, IATS,
ISL9

FUEL/WATER SEPARATOR
In addition to the standard fuel filters, a Racor 690R1210, 10 micron fuel/water separator with heater will be provided.
0887559 Trans, Allison 6th Gen, 3000 EVS P,
w/Prognostics, Imp/Vel/SFR/Enf

TRANSMISSION
An Allison 6th generation, Model EVS 3000P, electronic torque converting automatic transmission will be provided.

The transmission will be equipped with prognostics to monitor oil life, filter life, and transmission health. A wrench icon on the shift selector's digital display will indicate when service is due.

Two (2) PTO openings will be located on both sides of converter housing (positions 4 o'clock and 8 o'clock) as viewed from the rear.

A transmission temperature gauge with red light and audible alarm will be installed on the cab dash.
0625329 Transmission, Shifter, 5-Spd, Push
Button, 3000 EVS

TRANSMISSION SHIFTER
A five (5)-speed push button shift module will be mounted to right of driver on console. Shift position indicator will be indirectly lit for after dark operation.

The transmission ratio will be:
1st

3.49 to 1.00
2nd

1.86 to 1.00
3rd

1.41 to 1.00
4th

1.00 to 1.00
5th

0.75 to 1.00
R

5.03 to 1.00
0684459 Transmission Oil Cooler, Modine,
External

TRANSMISSION COOLER
A Modine plate and fin transmission oil cooler will be provided using engine coolant to control the transmission oil temperature.
0559012 Program, Transmission, Shift To
Neutral, With Prk Brk

TRANSMISSION PROGRAM
The transmission will shift to neutral when parking brake is set. 0801878 Fluid, 3000 Series Trans, Allison
Approved TES-668 Synthetic, IPOS,
Custom

TRANSMISSION FLUID
The transmission will be provided with TranSynd, or other Allison approved TES-668 heavy duty synthetic transmission fluid.
0001370 Driveline, Spicer 1710 DRIVELINE
Drivelines will be a heavy-duty metal tube and be equipped with Spicer® 1710 universal joints.

The shafts will be dynamically balanced before installation.

A splined slip joint will be provided in each driveshaft where the driveline design requires it. The slip joint will be coated with Glidecoat® or equivalent. 0635294 Steering, Single Gear, TRW TAS-85,
w/tilt, Pump w/ Cooler, Saber
FR/Enforcer

STEERING
Steering gear will be provided with integral heavy-duty power steering. For reduced system temperatures, the power steering will incorporate an air to oil cooler and Vickers® V 20NF hydraulic pump with integral pressure and flow control. All power steering lines will have wire braded lines with crimped fittings.

A tilt and telescopic steering column will be provided to improve fit for a broader range of driver configurations.
0605356 Steering Wheel, 4 Spoke without
Controls, Saber FR/Enforcer

STEERING WHEEL
The steering wheel will be 18.00" in diameter, have tilting and telescoping capabilities, and a 4- spoke design.

Bid #: 716 10
EXHIBIT 1 666
0550144 Logo/Emblem, on Horn Button LOGO AND CUSTOMER DESIGNATION ON HORN BUTTON The steering wheel will have an emblem containing the Pierce logo and customer name. The emblem will have three (3) rows of text for the customer's department name. There will be a maximum of eight (8) characters in the first row, 11 characters in the second row and 11 characters in the third row.

The first row of text will be: Stockton
The second row of text will be: Fire
The third row of text will be: Department
0624298 Bumper, 16" Extended, Saber
FR/Enforcer
BUMPER
A one (1) piece, ten (10) gauge, 304-2B type polished stainless steel bumper, minimum of 10.00" high, will be attached to a bolted modular extension frame constructed of 50,000 psi tensile steel "C" channel mounted directly behind it to provide adequate support strength.

The bumper will be extended 16.00" from front face of cab.

Gravel Pan
A gravel pan, constructed of bright aluminum treadplate, will be furnished between the bumper and cab face. The gravel pan will be properly supported from the underside to prevent flexing and vibration of the aluminum treadplate.
0640199 Tray, Hose, Center, 16" Bumper,
Outside Air Horns

CENTER HOSE TRAY
A hose tray, constructed of aluminum, will be placed in the center of the bumper extension.

The tray will have a capacity of 100' of 1.75" double jacket cotton-polyester hose.

Black rubber grating will be provided at the bottom of the tray. Drain holes are also provided. 0633479 Hose Restraint, Bumper Tray, Velcro
Straps, Pair
Center Hose Tray Restraint
There will be one (1) pair of hose tray restraint straps located over the center mounted tray.

The restraints will be a pair of 2.00" wide black nylon straps with Velcro® fasteners provided. The strap(s) will be used to secure the hose in the tray.
0614646 No Lift & Tow Package, Imp/Vel, AXT,
SFR/Enf
0002270 Tow Hooks, Chrome TOW HOOKS
Two (2) chromed steel tow hooks will be installed under the bumper and attached to the front frame members. The tow hooks will be designed and positioned to allow up to a 6,000 lb straight horizontal pull in line with the centerline of the vehicle. The tow hooks will not be used for lifting of the apparatus.
0645453 Travel Stop, Front Outlet Swivel,
Location

SWIVEL STOP
Installed on the front bumper extension will be a stainless steel rod to limit the travel of the front outlet swivel. The travel stop will be installed to keep it from hitting the left side front discharge.

One (1) stainless steel rod will be threaded into the bumper deck.

Bid #: 716 11
EXHIBIT 1 667
0625650 Cab, Enforcer, 7000 CAB
The Enforcer cab will be designed specifically for the fire service and manufactured by the chassis builder.

The cab will be built by the apparatus manufacturer in a facility located on the manufacturer's premises.

For reasons of structural integrity and enhanced occupant protection, the cab will be a heavy duty design, constructed to the following minimal standards.

The cab will have 12 main vertical structural members located in the A-pillar (front cab corner posts), B-pillar (side center posts), C-pillar (rear corner posts), and rear wall areas. The A-pillar will be constructed of solid A356-T5 aluminum castings. The B-pillar and C-pillar will be constructed from 0.13" wall extrusions. The rear wall will be constructed of two (2) 2.00" x 2.00" outer aluminum extrusions and two (2) 2.00" x 1.00" inner aluminum extrusions. All main vertical structural members will run from the floor to 4.625" x 3.864" x 0.090" thick roof extrusions to provide a cage-like structure with the A-pillar and roof extrusions being welded into a 0.25" thick corner casting at each of the front corners of the roof assembly.

The front of the cab will be constructed of a 0.13" firewall plate, covered with a 0.090" front skin (for a total thickness of 0.22"), and reinforced with a full width x 0.50" thick cross-cab support located just below the windshield and fully welded to the engine tunnel. The cross-cab support will run the full width of the cab and weld to each A-pillar, the 0.13" firewall plate, and the front skin.

The cab floors will be constructed of 0.125" thick aluminum plate and reinforced at the firewall with an additional 0.25" thick cross-floor support providing a total thickness of 0.375" of structural material at the front floor area. The front floor area will also be supported with two (2) triangular

0.30" wall extrusions that also provides the mounting point for the cab lift. This tubing will run from the floor wireway of the cab to the engine tunnel side plates, creating the structure to support the forces created when lifting the cab.

The cab will be 96.00" wide (outside door skin to outside door skin) to maintain maximum maneuverability.

The overall height (from the cab roof to the ground) of approximately 99.00". The overall height listed will be calculated based on a truck configuration with the lowest suspension weight rating, the smallest diameter tires for the suspension, no water weight, no loose equipment weight, and no personnel weight. Larger tires, wheels, and suspension will increase the overall height listed.

The floor to ceiling height inside the crew cab will be 54.50" in the center and outboard positions.

The crew cab floor will measure 46.00" from the rear wall to the back side of the rear facing seat risers.

The medium block engine tunnel, at the rearward highest point (knee level), will measure 61.50" to the rear wall. The big block engine tunnel will measure 51.50" to the rear wall.

The crew cab will be a totally enclosed design with the interior area completely open to improve visibility and verbal communication between the occupants.

The cab will be a full tilt cab style.

A 3-point cab mount system with rubber isolators will improve ride quality by isolating chassis vibrations from the cab.

CAB ROOF DRIP RAIL
For enhanced protection from inclement weather, a drip rail will be furnished on the sides of the cab. The drip rail will be painted to match the cab roof, and bonded to the sides of the cab. The drip rail will extend the full length of the cab roof.

INTERIOR CAB INSULATION
The cab will include 1.00" insulation in the ceiling, 1.50" insulation in the side walls, and 2.00" insulation in the rear wall to maximize acoustic absorption and thermal insulation.

FENDER LINERS
Full circular inner fender liners in the wheel wells will be provided.

PANORAMIC WINDSHIELD
A one (1)-piece safety glass windshield will be provided with over 2,775 square inches of clear viewing area. The windshield will be full width and will provide the occupants with a panoramic view. The windshield will consist of three (3) layers: outer light, middle safety laminate, and inner light. The outer light layer will provide superior chip resistance. The middle safety laminate layer will prevent the windshield glass pieces from detaching in the event of breakage. The inner light will provide yet another chip resistant layer. The cab windshield will be bonded to the aluminum windshield frame using a urethane adhesive. A custom frit pattern will be applied on the outside perimeter of the windshield for a finished automotive appearance.

WINDSHIELD WIPERS
Three (3) electric windshield wipers with washer will be provided that meet FMVSS and SAE requirements.

The washer reservoir will be able to be filled without raising the cab. 0647919 Engine Tunnel, ISL, Saber
FR/Enforcer

ENGINE TUNNEL
Engine hood side walls will be constructed of 0.375" aluminum. The top will be constructed of

0.125" aluminum and will be tapered at the top to allow for more driver and passenger elbow room.

The engine hood will be insulated for protection from heat and sound. The noise insulation keeps the dBA level within the limits stated in the current NFPA 1901 standards.

The engine tunnel will be no higher than 17.00" off the crew cab floor. 0633594 Rear Wall, Interior, Adjustable
Seating

INTERIOR CREW CAB REAR WALL ADJUSTABLE SEATING (PATENT PENDING) The interior rear wall of the crew cab will have mounting holes every 2.75" to allow for adjustability of the forward facing crew cab seating along the rear wall. Seats will be adjustable with use of simple hand tools allowing departments flexibility of their seating arrangement should their department needs change.
0632103 Rear Wall, Exterior, Cab, Saber
FR/Enforcer

CAB REAR WALL EXTERIOR COVERING
The exterior surface of the rear wall of the cab will be overlaid with brushed stainless steel except for areas that are not typically visible when the cab is lowered.

Bid #: 716 12
EXHIBIT 1 668
0639727 Cab Lift, Elec/Hyd, Manual Override,
Saber FR/Enforcer

CAB LIFT
A hydraulic cab lift system will be provided consisting of an electric powered hydraulic pump, dual lift cylinders, and necessary hoses and valves.

Hydraulic pump will have a manual override for backup in the event of electrical failure.

Lift controls will be located on the right side pump panel or front area of the body in a convenient location.

The cab will be capable of tilting 43 degrees to accommodate engine maintenance and removal.

The cab will be locked down by a 2-point normally closed spring loaded hook type latch that fully engages after the cab has been lowered. The system will be hydraulically actuated to release the normally closed locks when the cab lift control is in the raised position and cab lift system is under pressure. When the cab is completely lowered and system pressure has been relieved, the spring loaded latch mechanisms will return to the normally closed and locked position.

The hydraulic cylinders will be equipped with a velocity fuse that protects the cab from accidentally descending when the control is located in the tilt position.

For increased safety, a redundant mechanical stay arm will be provided that must be manually put in place on the left side between the chassis and cab frame when the cab is in the raised position. This device will be manually stowed to its original position before the cab can be lowered.

Cab Lift Interlock
The cab lift system will be interlocked to the parking brake. The cab tilt mechanism will be active only when the parking brake is set and the ignition switch is in the on position. If the parking brake is released, the cab tilt mechanism will be disabled. 0695930 Grille, Bright Finished, Front of Cab,
Enforcer
GRILLE
A bright finished aluminum mesh grille screen, inserted behind a bright finished grille surround, will be provided on the front center of the cab.
0002224 Scuffplates, S/S At Cab Door Jambs,
4-Door Cab

DOOR JAMB SCUFFPLATES
All cab door jambs will be furnished with a brushed stainless steel scuffplate, mounted on the striker side of the jamb.
0647932 Not Required, Trim, S/S Band, Across
Cab Face, AXT/Dash
CF/Saber/Enforcer
0087357 Molding, Chrome on Side of Cab SIDE OF CAB MOLDING Chrome molding will be provided on both sides of cab.
0521669 Mirrors, Retrac, West Coast Style,
Htd/Rmt, w/Htd/Rmt Convex

MIRRORS
A Retrac, Model 613423, dual vision, motorized, west coast style mirror, with chrome finish, will be mounted on each side of the front cab door with spring loaded retractable arms. The flat glass and convex glass will be heated and adjustable with remote control within reach of the driver. 0648171 Door, Half-Height, Saber FR/Enforcer
4-Door Cab, Level Roof
DOORS
To enhance entry and egress to the cab, the forward cab door openings will be a minimum of

37.50" wide x 63.37" high. The crew cab doors will be located on the sides of the cab and will be constructed in the same manner as the forward cab doors. The crew cab door openings will be a minimum of 34.30" wide x 63.37" high.

The forward cab and crew cab doors will be constructed of extruded aluminum with a nominal material thickness of 0.093". The exterior door skins will be constructed from 0.090" aluminum.

A customized, vertical, pull-down type door handle will be provided on the exterior of each cab door. The finish of the door handle will be chrome/black. The exterior handle will be designed specifically for the fire service to prevent accidental activation, and will provide 4.00" wide x 2.00" deep hand clearance for ease of use with heavy gloved hands.

Each door will also be provided with an interior flush, open style paddle handle that will be readily operable from fore and aft positions, and be designed to prevent accidental activation. The interior handles will provide 4.00" wide x 1.25" deep hand clearance for ease of use with heavy gloved hands.

The cab doors will be provided with both interior (rotary knob) and exterior (keyed) locks exceeding FMVSS standards. The keys will be Model 751. The locks will be capable of activating when the doors are open or closed. The doors will remain locked if locks are activated when the doors are opened, then closed.

A full length, heavy duty, stainless steel, piano-type hinge with a 0.38" pin and 11 gauge leaf will be provided on all cab doors. There will be double automotive-type rubber seals around the perimeter of the door framing and door edges to ensure a weather-tight fit.

A chrome handle will be provided on the inside of each cab door for ease of entry.

A red webbed grab handle will be installed on the crew cab door stop strap. The grab handles will be securely mounted.

The bottom cab step at each cab door location will be located below the cab doors and will be exposed to the exterior of the cab.
0655543 Door Panel, Brushed Stainless Steel,
Saber/Enforcer 4-Door Cab
Door Panels
The inner cab door panels will be constructed out of brushed stainless steel.

Bid #: 716 13
EXHIBIT 1 669
0630636 Controls, Electric Roll-Up Windows,
4dr, 4 Driver Controls, Saber
FR/Enforcer

ELECTRIC OPERATED CAB DOOR WINDOWS
All four (4) cab doors will be equipped with electric operated windows with one (1) flush mounted automotive style switch on each door. The driver's door will have four (4) switches, one (1) to control each door window.

Each switch will allow intermittent or auto down operation for ease of use. Auto down operation will be actuated by holding the window down switch for approximately 1 second. 0638310 Steps, 4-Door Cab, Saber
FR/Enforcer

CAB STEPS
The forward cab and crew cab access steps will be a full size two (2) step design to provide largest possible stepping surfaces for safe ingress and egress. The bottom steps will be designed with a grip pattern punched into bright aluminum treadplate material to provide support, slip resistance, and drainage. The bottom steps will be a bolt-in design to minimize repair costs should they need to be replaced. The forward cab steps will be a minimum 25.00" wide, and the crew cab steps will be 21.65" wide with a 10.00" minimum depth. The inside cab steps will not exceed 16.50" in height.

The vertical surfaces of the step well will be aluminum treadplate. 0770194 Handrail, Exterior, Knurled, Alum, 4-
Door Cab

CAB EXTERIOR HANDRAILS
A 1.25" diameter slip-resistant, knurled aluminum handrail will be provided adjacent to each cab and crew cab door opening to assist during cab ingress and egress. 0892638 Lights, Cab & Crw Cab Acs Stps,
P25, LED w/Bezel, 6lts

STEP LIGHTS
There will be six (6) white LED step lights with chrome housing installed for cab and crew cab access steps.

One (1) light for the left access steps.

Two (2) lights for the left side crew cab access steps.

Two (2) lights for the right side crew cab access steps.

One (1) light for the right side access step.

In order to ensure exceptional illumination, each light will provide a minimum of 25 foot-candles (fc) covering an entire 15" x 15" square placed ten (10) inches below the light and a minimum of

1.5 fc covering an entire 30" x 30" square at the same ten (10) inch distance below the light.

The lights will be activated when the battery switch is on and the adjacent door is opened. 0002141 Fenders, s/s on cab - Saber/Enforcer FENDER CROWNS Stainless steel fender crowns will be installed at the cab wheel openings. 0630508 Window, Side of C/C, Fixed,
Passenger Side Only, Saber
FR/Enforcer

CREW CAB WINDOW
One (1) fixed window with tinted glass will be provided on the passenger side of the cab, to the rear of the front cab door. The window will be sized to enhance light penetration into the cab interior and will measure 18.70" wide x 23.75" high. There will be no window provided on the driver side of the cab.
0621136 Compt, Storage, 12.75 W x 24 H x 15
D, (1) Ea Side C/C, Dbl Pan, 70"
SFR/Enf

STORAGE COMPARTMENTS
Provided on each side of the cab, to the rear of the crew cab access doors, will be a storage compartment. The compartments will be approximately 12.75" wide x 24.00" high x 15.00" deep.

There will be two (2) double pan doors painted to match the cab exterior with a non-locking DRing latch, one (1) on each side of the cab. A chain for each exterior door will be used as a doorstop. The clear door opening will be 10.50" wide x 22.50" high.

The compartment interior will be painted to match the cab interior.

Compartment Lights
There will be two (2) white Amdor, LED strip lights provided, one (1) each hinged side of compartment door openings.
0618351 Glove Box, Front of Officer, Saber
FR/Enforcer

GLOVE BOX
A glove box with a drop-down door will be installed above the recessed area of the dash panel in front of the officer's position. The glove box will be 31.00" wide at the top and 24.75" at the bottom x 5.50" high x 6.25" deep. The clear door opening will be 14.25" wide x 3.95" high. 0894089 Dash, Heavy Duty Metal, Enforcer CAB DASH
The driver side dash, switch panel located to the right of the driver, and center console will be constructed of aluminum and painted fire smoke gray.

The officer side dash will be a flat top design with an upper beveled edge to provide easy maintenance and will be constructed out of aluminum and painted to match the cab interior.

The instrument gauge cluster will be surrounded with a high impact ABS plastic contoured to the same shape of the instrument gauge cluster.

Bid #: 716 14
EXHIBIT 1 670
0722652 SP Work Surface, 1/4" Alum, Full Eng
Tnl, Flat, Sp Lwr Rr, Lip, Encl
Sides/Frt, Enf

WORK SURFACE ON ENGINE TUNNEL
There will be a work surface provided on the engine tunnel. The work surface will cover the entire engine tunnel and follow the width of the engine tunnel. It will be constructed of 0.25" aluminum.

The beginning of the work surface will start 6.00" behind the instrument panel for accessibility to switch panels. The front and sides of the work surface will flange down to enclosure the area below. The work surface will be flat from the front of the engine tunnel to 20.00" from the rear edge of the engine tunnel. At this point, the work surface will flange down 90 degrees and then extend to the rear of the engine tunnel, following the contour of the tunnel. The lower rear portion of the tunnel will be provided with a 4.00" lip on three (3) sides.

The mounting surface will be painted to match the cab interior. 0664465 Bracket, Air Bottle, Hands-Free II AIR BOTTLE HOLDERS There will be one (1) Gen II Hands-Free bracket(s) provided in the crew cab. For efficiency and convenience, the bracket will include an automatic spring clamp that allows the user to store the SCBA bottle by simply pushing it into the bracket. For protection of all occupants in the cab, in the event of an accident, the inertial components within the clamp will constrain the SCBA bottle for up to a 9G force (dynamic sled test), which meets NFPA standard.

The bracket(s) will be located mounted to option #664484. 0664484 Bracket, 45 Degrees, To Mount Air
Bottle Bracket, Wall Mounted, Crew
Cab

BRACKET TO MOUNT SCBA HOLDER
There will be one (1) bracket(s) provided for mounting air bottle brackets. Each bracket will be mounted on a 45 degree angle mounting plate located in the crew cab. Each mounting bracket will be designed to hold one (1) Ziamatic SCBA holder.

The bracket(s) will be mounted DS.
0750824 Cab Interior, Vinyl Headliner, Saber
FR/Enforcer, CARE

CAB INTERIOR
The cab interior will be constructed of primarily metal (painted aluminum) to withstand the severe duty cycles of the fire service.

The engine tunnel will be padded and covered, on the top and sides, with dark silver gray 36 ounce leather grain vinyl resistant to oil, grease, and mildew.

For durability and ease of maintenance, the cab interior side walls will be painted aluminum. The rear wall will be painted aluminum.

The headliner will be installed in both forward and rear cab sections. Headliner material will be vinyl. A sound barrier will be part of its composition. Material will be installed on an aluminum sheet and securely fastened to interior cab ceiling.

The forward portion of the cab headliner will permit easy access for service of electrical wiring or other maintenance needs.

All wiring will be placed in metal raceways.

CAB INTERIOR UPHOLSTERY
The cab interior upholstery will be 36 oz dark silver gray vinyl. 0753903 Cab Interior, Paint Color, Saber
FR/Enforcer

CAB INTERIOR PAINT
The cab interior metal surfaces, excluding the rear heater panels, will be painted fire smoke gray, vinyl texture paint.

The rear heater panels will be painted black, vinyl textured paint. 0012101 Floor, Aluminum Treadplate, Cab &
Crew Cab, Saber/Enforcer, CARE

CAB FLOOR
The cab and crew cab flooring will be constructed with bright aluminum treadplate.

Bid #: 716 15
EXHIBIT 1 671
0722696 HVAC, Enforcer, CARE DEFROST/AIR CONDITIONING SYSTEM A ceiling mounted combination heater, defroster and air conditioning system will be installed in the cab above the engine tunnel area.

Cab Defroster
A 54,000 BTU heater-defroster unit with 690 SCFM of air flow will be provided inside the cab. The heater-defrost will be installed in the forward portion of the cab ceiling. Air outlets will be strategically located in the cab header extrusion per the following:

One (1) adjustable will be directed towards the left side cab window One (1) adjustable will be directed towards the right side cab window Six (6) fixed outlets will be directed at the windshield The defroster will be capable of clearing 98 percent of the windshield and side glass when tested under conditions where the cab has been cold soaked at 0 degrees Fahrenheit for 10 hours, and a 2 ounce per square inch layer of frost/ice has been able to build up on the exterior windshield.

The defroster system will meet or exceed SAE J382 requirements.

Cab/Crew Auxiliary Heater
There will be one (1) 31,000 BTU auxiliary heater with 560 SCFM of air flow provided in each outboard rear facing seat risers with a dual scroll blower. An aluminum plenum incorporated into the cab structure used to transfer heat to the forward positions.

Air Conditioning
A condenser will be a 59,644 BTU output that meets and exceeds the performance specification will be mounted on the radiator.

The air conditioning system will be capable of cooling the average cab temperature from 100 degrees Fahrenheit to 75 degrees Fahrenheit at 50 percent relative humidity within 30 minutes.

The cooling performance test will be run only after the cab has been heat soaked at 100 degrees Fahrenheit for a minimum of 4 hours.

The evaporator unit will be installed in the rear portion of the cab ceiling over the engine tunnel.

The evaporator will include one (1) high performance heating core, one (1) high performance cooling core with (1) plenum directed to the front and one (1) plenum directed to the rear of the cab. The rear plenum will be covered with a metal cover painted to match the cab interior.

The evaporator unit will have a 52,000 BTU at 690 SCFM rating that meets and exceeds the performance specifications.

Adjustable air outlets will be strategically located on the forward plenum cover per the following:

Four (4) will be directed towards the seating position on the left side of the cab Four (4) will be directed towards the seating position on the right side of the cab Adjustable air outlets will be strategically located on the rear plenum cover per the following:

Minimum of five (5) will be directed towards crew cab area A high efficiency particulate air (HEPA) filter will be included for the system. Access to the filter cover will be secured with four (4) screws.

The air conditioner refrigerant will be R-134A and will be installed by a certified technician.

Climate Control
An automotive style controller will be provided to control the heat and air conditioning system within the cab. The controller will have three (3) functional knobs for fan speed, temperature, and air flow distribution (front to rear) control.

The system will control the temperature of the cab and crew cab automatically by pushing the center of the fan speed control knob. Rotate the center temperature control knob to set the cab and crew cab temperature.

The AC system will be manually activated by pushing the center of the temperature control knob.

Pushing the center of the air flow distribution knob will engage the AC for max defrost, setting the fan speeds to 100 percent and directing all air flow to the overhead forward position.

The system controller will be located within panel position #12.

Gravity Drain Tubes
Two (2) condensate drain tubes will be provided for the air conditioning evaporator. The drip pan will have two (2) drain tubes plumbed separately to allow for the condensate to exit the drip pan.

No pumps will be provided.
0639675 Sun Visor, Smoked Lexan, AXT,
Imp/Vel, Saber FR/Enforcer

SUN VISORS
Two (2) smoked Lexan™ sun visors will be provided. The sun visors will be located above the windshield with one (1) mounted on each side of the cab.

There will be no retention bracket provided to help secure each sun visor in the stowed position. 0622887 Grab Handles, Driver Door Post,
Officer Door Post Low, Saber
FR/Enforcer

GRAB HANDLE
A black rubber covered grab handle will be mounted on the door post of the driver and officer's side cab door to assist in entering the cab. The officer's side grab handle will be mounted on the lower portion of the door post. The grab handle will be securely mounted to the post area between the door and windshield.
0793781 Lights, Engine Compt, Custom, Auto
Sw, TecNiq E18-LC00-1 LED

ENGINE COMPARTMENT LIGHTS
There will be two (2) TecNiq, part number E18-LC00-1, 800 lumens 2.50" high x 4.50" long 12 volt DC, light(s) with white LEDs installed under the cab to be used as engine compartment illumination.

These light(s) will be activated automatically when the battery switch is on and the cab is raised. 0631830 Fluid Check Access, Saber
FR/Enforcer, Arrow XT

ACCESS TO ENGINE DIPSTICKS
For access to the engine oil and transmission fluid dipsticks, there will be a door on the engine tunnel, inside the crew cab. The door will be on the rear wall of the engine tunnel, on the vertical surface.

The engine oil dipstick will allow for checking only. The transmission dipstick will allow for both checking and filling.

The door will have a rubber seal for thermal and acoustic insulation. One (1) flush lift and turn latch will be provided on the access door.

Bid #: 716 16
EXHIBIT 1 672
0599959 Straps, Velcro, Map Box, Custom
Chassis

VELCRO STRAP(S) FOR MAP BOX
There will be one (1) Velcro® strap(s) installed at final inspection. 0758719 SP Box, Open from Top, Custom
Chassis, Dividers, Cup, Bin, 3.75" H x
11"W x 20"L

OPEN TOP STORAGE BIN
An open top bin with dividers, will be installed TBD at final inspection (similar to job 36054 01-02).

The bin will be 3.75" high x 11.00" wide x 20.00" long.

The front 3.00" will be a solid surface for mounting of equipment and will be 3.00" high. The middle 10.50" length of the bin will be open with a divider splitting the area into two (2) equal spaces each 5.50" wide; the sides of this area will be 2.00" high. The next 2.00" will be left open for storage. The space will be 3.75" high x 11.00" wide x 2.00" long.

The remaining space will provide a cutout for two (2) cup holders, one on each side. The area will be sealed from the other compartments. A bin will be provided in the space between the cup holders. The bin will be 2.75" wide x 3.75" long.

The bin will be constructed of .125" aluminum and will be painted to match the cab interior. 0002501 Map box, 4 bin/30 Deg Slant, Custom
Chassis

MAP BOX
A map box with four (4) bins, open from top, will be installed inside vertical wall of the left side rear facing compartment (match job 36054 01-02). SEE PHOTO. The map box will be divided into four (4) bins, each being 12.50" wide x 2.25" high x 12.00" deep. Each bin will slant 30 degrees from horizontal. The map box will be constructed of .125" aluminum and will be painted to match the cab interior.
0583039 Not Required, Side Roll and Frontal
Impact Protection
0622619 Seating Capacity, 4 Seats

SEATING CAPACITY
The seating capacity in the cab will be four (4).
0795902 Seat, Driver, USSC, Valor, P1A, Air
Ride, R-Back, Saber FR/Enforcer

DRIVER SEAT
A USSC Valor air suspension R-back seat will be provided in the cab for the driver. For increased convenience, the seat will include a manual control to adjust the horizontal position. To provide flexibility for multiple driver configurations, the seat will have a reclining back, adjustable from 15 degrees back to 45 degrees forward.

The seat will be furnished with a 3-point, shoulder type seat belt.

There will be no additional contaminant mitigation vinyl covers shipped loose with the seat. 0795051 Seat, Officer, USSC, Valor, P1A, Air
Ride, SCBA, Saber FR/Enforcer

OFFICER SEAT
A USSC, P1A, SCBA air suspension seat will be provided in the cab for the officer. For optimal comfort, the seat will be provided with 17.00" deep cushion. For increased convenience, the seat will include a manual control to adjust the height (3.00" travel) and horizontal position (4.25" travel).

The seat back will be an SCBA back style with a 5 degree fixed recline angle. The SCBA cavity will be adjustable from front to rear in 0.75" increments to accommodate different sized SCBA cylinders. Moving the SCBA cavity will be accomplished by unbolting, relocating, and re-bolting it in the desired location.

The seat will be furnished with a 3-point, shoulder type seat belt.

Shipped loose with the seat will be no additional contaminant mitigation vinyl covers. 0002517 Not Required, Radio Compartment
0771202 Cabinet, Rear Facing, LS, 23 W x 39
H x 26.75 D, Lap, SFR/Enf

REAR FACING LEFT SIDE CABINET
A rear facing cabinet will be provided in the crew cab at the left side outboard position.

The cabinet will be 23.00" wide x 39.00" high x 26.75" deep with one (1) lap door hinged on the outbard side, panted to match the cab interior with two (2) non-locking lever latches. The interior clear door opening of the cabinet will be 20.50" wide x 36.50" high.

The cabinet will include two (2) infinitely adjustable shelves with a 1.25" up-turned lipwith a dual action finish.

The cabinet will include louvers provided on the right side of the cabinet for ventilation, louvers provided on the door of the cabinet for ventilation and louvers provided on the back side of the cabinet for ventilation.

The cabinet will be constructed of smooth aluminum and painted to match the cab interior.

Cabinet Light
There will be one (1) white Amdor LED strip light installed on the left side of the interior cabinet door opening. The lights will be controlled by an automatic door switch. 0102783 Not Required, Seat, Rr Facing C/C,
Center
Bid #: 716 17
EXHIBIT 1 673
0795803 SP Seat, Rear Facing C/C, PS Outboard,
USSC, Valor, SCBA, 17" Bottom,
Saber FR/Enf

REAR FACING PASSENGER SIDE OUTBOARD SEAT
There will be one (1) rear facing, USSC Valor, SCBA seat provided at the passenger side outboard position in the crew cab. For optimal comfort, the seat will be provided with 17.00" deep cushion.

The seat back will be an SCBA back style with 5 degree fixed recline angle. The SCBA cavity will be adjustable from front to rear in 1.00" increments, to accommodate different sized SCBA cylinders. Moving the SCBA cavity will be accomplished by unbolting, relocating, and re-bolting it in the desired location.

The seat will be furnished with a 3-point, shoulder type seat belt. 0108189 Not Required, Seat, Forward Facing
C/C, DS Outboard
0740984 SP Seat, Forward Facing C/C, Center,
(1) USSC, Valor, SCBA, 95 D, 17"
Btm, SFR/Enf

FORWARD FACING CENTER SEAT
There will be one (1) forward facing, USSC Valor seat provided at the center position in the crew cab. For optimal comfort, the seat will be provided with a 17.00" deep foam cushion.

The seat back will be an SCBA style with 95 degree back. The SCBA cavity will be adjustable from front to rear in 0.75" increments, to accommodate different sized SCBA cylinders. Moving the SCBA cavity will be accomplished by unbolting, relocating, and re-bolting it in the desired location.

The seat will be furnished with a 3-point, shoulder type seat belt. 0108190 Not Required, Seat, Forward Facing
C/C, PS Outboard
0625186 Upholstery, Seats In Cab, All
VALORTechXD (Cordura), USSC

SEAT UPHOLSTERY
All seat upholstery will be gray, sewn with red stitching, VALORTechXD anti-microbial material. 0543991 Bracket, Air Bottle, Hands-Free II,
Cab Seats

AIR BOTTLE HOLDERS
All SCBA type seats in the cab will have a "Hands-Free" auto clamp style bracket in its backrest.

For efficiency and convenience, the bracket will include an automatic spring clamp that allows the occupant to store the SCBA bottle by simply pushing it into the seat back. For protection of all occupants in the cab, in the event of an accident, the inertial components within the clamp will constrain the SCBA bottle in the seat and will exceed the NFPA standard of 9G.

There will be a quantity of three (3) SCBA brackets.
0603866 Seat Belt, Dual Retractor,
ReadyReach, Saber FR/Enforcer

SEAT BELTS
All cab and tiller cab (if applicable) seating positions will have red seat belts. To provide quick, easy use for occupants wearing bunker gear, the female buckle and seat belt webbing length will meet or exceed the current edition of NFPA 1901 and CAN/ULC - S515 standards.

The 3-point shoulder type seat belts will include height adjustment. This adjustment will optimize the belts effectiveness and comfort for the seated firefighter. The 3-point shoulder type seat belts will be furnished with dual automatic retractors that will provide ease of operation in the normal seating position.

The 3-point shoulder type belts will also include the ReadyReach D-loop assembly to the shoulder belt system. The ReadyReach feature adds an extender arm to the D-loop location placing the D-loop in a closer, easier to reach location.

Any flip up seats will include a 3-point shoulder type belts only.

To ensure safe operation, the seats will be equipped with seat belt sensors in the seat cushion and belt receptacle that will activate an alarm indicating a seat is occupied but not buckled. 0602464 Helmet Storage, Provided by Fire
Department, NFPA 2016

HELMET STORAGE PROVIDED BY FIRE DEPARTMENT
NFPA 1901, 2016 edition, section 14.1.7.4.1 requires a location for helmet storage be provided.

There is no helmet storage on the apparatus as manufactured. The fire department will provide a location for storage of helmets.
0600601 Lights, Dome, FRP Dual LED 4 Lts,
Non-MUX

CAB DOME LIGHTS
There will be four (4) dual LED dome lights with black bezels provided. Two (2) lights will be mounted above the inside shoulder of the driver and officer and two (2) lights will be installed and located, one (1) on each side of the crew cab.

The color of the LED's will be red and white.

The white LED's will be controlled by the door switches.

The color LED's will be controlled by the lens switch.

In order to ensure exceptional illumination, each white LED dome light will provide a minimum of

10.1 foot-candles (fc) covering an entire 20.00" x 20.00" square seating position when mounted

40.00" above the seat.
0602635 Portable Hand Light, Provided by
Dealer, Pumper NFPA 2016
Classification

PORTABLE HAND LIGHTS, PROVIDED BY DEALER
NFPA 1901, 2016 edition, section 5.9.4 requires two portable hand lights mounted in brackets fastened to the apparatus.

The hand lights are not on the apparatus as manufactured. The dealer will provide and mount these hand lights.
0644187 Cab Instruments, Black Gauges, CAB INSTRUMENTATION Bid #: 716 18
EXHIBIT 1 674
Black Bezels, Saber FR/Enforcer The cab instrument panel will include gauges, telltale indicator lamps, control switches, alarms, and a diagnostic panel. The function of the instrument panel controls and switches will be identified by a label adjacent to each item. Actuation of the headlight switch will illuminate the labels in low light conditions. Telltale indicator lamps will not be illuminated unless necessary. The cab instruments and controls will be conveniently located within the forward cab section, forward of the driver. The gauge assembly and switch panels are designed to be removable for ease of service and low cost of ownership.

Gauges
The gauge panel will include the following ten (10) black faced gauges with black bezels to monitor vehicle performance:

Voltmeter gauge (volts):

Low volts (11.8 VDC)
Amber telltale light on indicator light display with steady tone alarm High volts (15.5 VDC)
Amber telltale light on indicator light display with steady tone alarm Engine Tachometer (RPM)
Speedometer MPH (Major Scale), KM/H (Minor Scale)
Fuel level gauge (Empty - Full in fractions):

Low fuel (1/8 full)
Amber indicator light in gauge dial with steady tone alarm Engine Oil pressure Gauge (PSI):

Low oil pressure to activate engine warning lights and alarms Red indicator light in gauge dial with steady tone alarm Front Air Pressure Gauges (PSI):

Low air pressure to activate warning lights and alarm
Red indicator light in gauge dial with steady tone alarm Rear Air Pressure Gauges (PSI):

Low air pressure to activate warning lights and alarm
Red indicator light in gauge dial with steady tone alarm Transmission Oil Temperature Gauge (Fahrenheit):

High transmission oil temperature activates warning lights and alarm Amber indicator light in gauge dial with steady tone alarm Engine Coolant Temperature Gauge (Fahrenheit):

High engine temperature activates an engine warning light and alarms Red indicator light in gauge dial with steady tone alarm Diesel Exhaust Fluid Level Gauge (Empty - Full in fractions):

Low fluid (1/8 full)
Amber indicator light in gauge dial
Indicator Lamps
To promote safety, the following telltale indicator lamps will be located on the instrument panel in clear view of the driver. The indicator lamps will be "dead-front" design that is only visible when active. The colored indicator lights will have descriptive text or symbols.

The following amber telltale lamps will be present:

Low coolant
Trac cntl (traction control) (where applicable)
Check engine
Check trans (check transmission)
Air rest (air restriction)
DPF (engine diesel particulate filter regeneration)
HET (engine high exhaust temperature) (where applicable) ABS (antilock brake system)
MIL (engine emissions system malfunction indicator lamp) (where applicable) Regen inhibit (engine emissions regeneration inhibit) (where applicable) Side roll fault (where applicable)
Front air bag fault (where applicable)
Aux brake overheat (auxiliary brake overheat) (where applicable) The following red telltale lamps will be present:

Ladder rack down
Parking brake
Stop engine
The following green telltale lamps will be present:

Left turn
Right turn
Battery on
Ignition
Aux brake (auxiliary brake engaged) (where applicable)
The following blue telltale lamps will be present:

High beam
Alarms
Audible steady tone warning alarm: A steady audible tone alarm will be provided whenever a warning condition is active.

Indicator Lamp and Alarm Prove-Out
A system will be provided which automatically tests telltale indicator lights and alarms located on the cab instrument panel. Telltale indicators and alarms will perform prove-out for 3 to 5 seconds when the ignition switch is moved to the on position with the battery switch on.

Control Switches
For ease of use, the following controls will be provided immediately adjacent to the cab instrument panel within easy reach of the driver. All switches will have backlit labels for low light applications.

Headlight/Parking light switch: A three (3)-position maintained rocker switch will be provided. The first switch position will deactivate all parking and headlights. The second switch position will activate the parking lights. The third switch will activate the headlights.

Panel back lighting intensity control switch: A three (3)-position momentary rocker switch will be provided. Pressing the top half of the switch, "Panel Up" increases the panel back lighting intensity and pressing the bottom half of the switch, "Panel Down" decreases the panel back lighting intensity. Pressing the half or bottom half of the switch several times will allow back lighting intensity to be gradually varied from minimum to maximum intensity level for ease of use.

Ignition switch: A three (3)-position maintained/momentary rocker switch will be provided. The first Bid #: 716 19
EXHIBIT 1 675
switch position will turn off and deactivate vehicle ignition. The second switch position will activate vehicle ignition and will perform prove-out on the telltale indicators and alarms for 3 to 5 seconds after the switch is turned on. A green indicator lamp is activated with vehicle ignition. The third momentary position will temporarily silence all active cab alarms. An alarm "chirp" may continue as long as alarm condition exists. Switching ignition to off position will terminate the alarm silence feature and reset function of cab alarm system.

Engine start switch: A two (2)-position momentary rocker switch will be provided. The first switch position is the default switch position. The second switch position will activate the vehicle's engine. The switch actuator is designed to prevent accidental activation.

Hazard switch will be provided on the instrument panel or on the steering column.

Heater, defrost, and air conditioning control panel.

Turn signal arm: A self-canceling turn signal with high beam headlight controls.

Windshield wiper control will have high, low, and intermittent modes.

Parking brake control: An air actuated push/pull park brake control.

Chassis horn control: Activation of the chassis horn control will be provided through the center of the steering wheel.

High idle engagement switch: A maintained rocker switch with integral indicator lamp will be provided. The switch will activate and deactivate the high idle function. The "OK To Engage High Idle" indicator lamp must be active for the high idle function to engage. A green indicator lamp integral to the high idle engagement switch will indicate when the high idle function is engaged. "OK To Engage High Idle" indicator lamp: A green indicator light will be provided next to the high idle activation switch to indicate that the interlocks have been met to allow high idle engagement.

Emergency switching will be controlled by multiple individual warning light switches for various groups or areas of emergency warning lights. An Emergency Master switch provided on the instrument panel that enables or disables all individual warning light switches is included.

An additional "Emergency Master" button will be provided on the lower left hand corner of the gauge panel to allow convenient control of the "Emergency Master" system from inside the driver's door when standing on the ground.

Custom Switch Panels
The design of cab instrumentation will allow for emergency lighting and other switches to be placed within easy reach of the operator thus improving safety. There will be positions for up to four (4) switch panels in the lower instrument console and up to six (6) switch panels in the overhead visor console. All switches have backlit labels for low light conditions.

Diagnostic Panel
A diagnostic panel will be provided and accessible while standing on the ground.

The panel will be located inside the driver's side door left of the steering column.

The diagnostic panel will allow diagnostic tools such as computers to connect to various vehicle systems for improved troubleshooting providing a lower cost of ownership. Diagnostic switches will allow ABS systems to provide blink codes should a problem exist.

The diagnostic panel will include the following:

ENGINE/TRANSMISSION/ABS J1939 Diagnostic Port
ABS Diagnostic Switch and Indicator - The switch and amber indicator will allow access to diagnostic mode and display of standard ABS system fault blink codes that may be generated by the ABS system
DPF REGEN (Diesel Particulate Filter Regeneration Switch) (where applicable) will be provided to request regeneration of the engine emission system. An amber indicator will be provided on top of the switch that will illuminate in a "CHECK ENGINE" condition
REGEN INHIBIT (Diesel Particulate Filter Regeneration Inhibit Switch) (where applicable) will be provided that will request that regeneration be temporarily prevented. A green indicator will be provided on top of the Regen Inhibit switch that will illuminate when the Regen Inhibit feature is active. Regen Inhibit will be disabled upon cycling of the ignition switch to the off state.
0002544 Air Restriction Indicator - Pierce
Chassis

AIR RESTRICTION INDICATOR
A high air restriction warning indicator light (electronic) will be provided. 0673123 Light, Do Not Move Apparatus, Wln
3SR00FRR LED
"DO NOT MOVE APPARATUS" INDICATOR
A Whelen Model 3SR00FRR flashing red LED indicator light with a Whelen, Model 3FLANGEC chrome surface mount flange located in the driving compartment, will be illuminated automatically per the current NFPA requirements. The light will be labeled "Do Not Move Apparatus If Light Is On".

The same circuit that activates the Do Not Move Apparatus indicator will activate a pulsing alarm when the parking brake is released.
0637359 Not Required, Door Open Indicator
w/Do Not Move Truck Light,
Enf/Saber FR
0632738 Switching, Cab Instrument Lower
Console & Overhead, Rocker,
Enforcer

SWITCH PANELS
The built-in switch panels will be located in the lower console or overhead console of the cab.

Switches will be rocker type with an indicator light, of which is an integral part of the switch. 0802940 Wiper Control, 2-Speed with
Intermittent, Saber FR/Enforcer

WIPER CONTROL
Wiper control will consist of a two (2)-speed windshield wiper control with intermittent feature and windshield washer controls. The control will be located above the ignition switch.

Bid #: 716 20
EXHIBIT 1 676
0797189 Wiring, Spare, 4.8 A 12V DC, USB
Termination Blue Sea 1045 1st

SPARE CIRCUIT
There will be one (1) dual USB fast charge socket mounts installed on the apparatus.

The above wires will have the following features:

The positive wire will be connected directly to the battery power.

The negative wire will be connected to ground.

Wires will be protected to 4.8 amps at 12 volts DC.

The USB socket mount will be switch panel #13.

Termination will be a Blue Sea Systems part number 1045 dual USB charger socket.

Wires will be sized to 125% of the protection.

This circuit(s) may be load managed when the parking brake is applied. 0787001 Wiring, Spare, 4.8 A 12V DC, USB
Termination Blue Sea 1045 2nd

SPARE CIRCUIT
There will be one (1) dual USB fast charge socket mounts installed on the apparatus.

The above wires will have the following features:

The positive wire will be connected directly to the battery power.

The negative wire will be connected to ground.

Wires will be protected to 4.8 amps at 12 volts DC.

The USB socket mount will be left side rear most corner of work surface (option 0722652) that is on top of the engine tunnel per job 36054 01-02 (SEE PHOTO - SFD 03).

Termination will be a Blue Sea Systems part number 1045 dual USB charger socket.

Wires will be sized to 125% of the protection.

This circuit(s) may be load managed when the parking brake is applied. 0897539 SP Wiring, Spare, 37.5 A 12V DC, Cust
Install Radio, 30A Isolated, 7.5A Ign &
Grnd

CUSTOMER SUPPLIED RADIO WIRING
There will be one (1) 12 volt combination wiring leads of which each will include one (1) isolated battery, one (1) ignition and one (1) negative ground for use with customer provided and installed radio equipment.

Each lead will be routed to the left side rear facing compartment (option 0771803). Leave 4' of wires coiled up with an 18.00" long pigtail. The leads will be clearly marked in a coil and terminate with butt splices.

A breaker rated for 30 amps will be provided for circuit protection of the isolated battery lead with 10 gauge wire.

A breaker rated for 7.5 amps will be provided for circuit protection of the ignition lead.

A 10 gauge negative ground will be provided.

The wires will be colored coded as follows:

White for isolated battery
Yellow for ignition
Black for negative ground
0585913 Wiring, Spare, 20 A 12V DC, 6 Circuit
Fuse Block, Blue Sea 5025 2nd

SPARE CIRCUIT
There will be one (1) pair of wires, including a positive and a negative, installed on the apparatus.

The above wires will have the following features:

The positive wire will be connected directly to the battery power.

The negative wire will be connected to ground.

Wires will be protected to 20 amps at 12 volts DC.

Power and ground will terminate on the backside vertical surface of the LS rear facing compartment, inboard towards the engine tunnel down low for easy access.

Termination will be to a Blue Sea System, Model 5025, 6 circuit with negative bus bar. The terminal block will include a cover with circuit labels.

Wires will be sized to 125% of the protection.

This circuit(s) may be load managed when the parking brake is set. 0585914 Wiring, Spare, 20 A 12V DC, 6 Circuit
Fuse Block, Blue Sea 5025 1st

SPARE CIRCUIT
There will be one (1) pair of wires, including a positive and a negative, installed on the apparatus.

The above wires will have the following features:

The positive wire will be connected directly to the battery power.

The negative wire will be connected to ground.

Wires will be protected to 20 amps at 12 volts DC.

Power and ground will terminate RUN WIRES ONLY to RS1 on the left inside wall, upper back corner. Leave 5' of extra wire coiled up, final location TBD @ final inspection.

Termination will be to a Blue Sea System, Model 5025, 6 circuit with negative bus bar. The terminal block will include a cover with circuit labels.

Wires will be sized to 125% of the protection.

This circuit(s) may be load managed when the parking brake is set. 0547328 Wiring, Spare, 20 A 12V DC, Switch
Feature 1st

SPARE CIRCUIT
There will be one (1) pair of wires, including a positive and a negative, installed on the apparatus.

The above wires will have the following features:

The positive wire will be connected directly to the battery power.

The negative wire will be connected to ground.

Wires will be protected to 20 amps at 12 volts DC.

Power and ground will terminate switch panel #9, position #4 labeled "KNOX". Terminate wire behind left side of switch panel #13 w/ 24" of slack.

Termination will be with heat shrinkable butt splicing.

The circuits selected above will be controlled by a switch in the following locations:
a switch in the driver's side switch panel
no additional switch location
Wires will be sized to 125% of the protection.

This circuit(s) may be load managed when the parking brake is set.

Bid #: 716 21
EXHIBIT 1 677
0547505 Wiring, Spare, 10 A 12V DC 1st SPARE CIRCUIT
There will be four (4) pair of wires, including a positive and a negative, installed on the apparatus.

The above wires will have the following features:

The positive wire will be connected directly to the battery power.

The negative wire will be connected to ground.

Wires will be protected to 10 amps at 12 volts DC.

Power and ground will terminate (1) each under the slanted portion outboard of the driver and officer's seat, (1) under the center forward facing seat base and (1) to the back of the engine tunnel (these will be used for dealer installed flashlights).

Termination will be with heat shrinkable butt splicing.

Wires will be sized to 125 percent of the protection.

This circuit(s) may be load managed when the parking brake is applied. 0548006 Wiring, Spare, 15 A 12V DC 2nd SPARE CIRCUIT
There will be one (1) pair of wires, including a positive and a negative, installed on the apparatus.

The above wires will have the following features:

The positive wire will be connected directly to the battery power.

The negative wire will be connected to ground.

Wires will be protected to 15 amps at 12 volts DC.

Power and ground will terminate switch panel #13.

Termination will be with 15 amp, power point plug with rubber cover.

Wires will be sized to 125 percent of the protection.

This circuit(s) may be load managed when the parking brake is set. 0655679 Remote Control, Wired,
Programmable 3 Button

PROGRAMMABLE REMOTE CONTROL
There will be a wired remote control integrated into the switch panel overhead panel location A, next to the SBMS display. The remote will have three (3) individually programmable buttons for most garage door openers, and gate operators as well as the capability of controlling many lighting and security systems.
0763646 Vehicle Information Center, LCD On
Gauge Cluster Only, Sab/Enf

INFORMATION CENTER
There will be a LCD display integral to the cab gauge panel provided that will display the following information:

Total distance
Trip distance
Total hours
Trip hours
PTO "A" hours
PTO "B" hours
0734854 Collision Mitigation, Not Requested
0610240 Vehicle Data Recorder w/Seat Belt
Monitor

VEHICLE DATA RECORDER
There will be a vehicle data recorder (VDR) capable of reading and storing vehicle information provided.

The information stored on the VDR can be downloaded through a USB port mounted in a convenient location determined by cab model. A USB cable can be used to connect the VDR to a laptop to retrieve required information. The program to download the information from the VDR will be available to download on-line.

The vehicle data recorder will be capable of recording the following data via hardwired and/or CAN inputs:

Vehicle Speed - MPH
Acceleration - MPH/sec
Deceleration - MPH/sec
Engine Speed - RPM
Engine Throttle Position - % of Full Throttle
ABS Event - On/Off
Seat Occupied Status - Yes/No by Position
Seat Belt Buckled Status - Yes/No by Position
Master Optical Warning Device Switch - On/Off
Time - 24 Hour Time
Date - Year/Month/Day
Seat Belt Monitoring System
A seat belt monitoring system (SBMS) will be provided. The SBMS will be capable of monitoring up to 10 seating positions indicating the status of each seat position per the following:

Seat Occupied & Buckled = Green LED indicator illuminated Seat Occupied & Unbuckled = Red LED indicator with audible alarm No Occupant & Buckled = Red LED indicator with audible alarm No Occupant & Unbuckled = No indicator and no alarm
The SBMS will include an audible alarm that will warn that an unbuckled occupant condition exists and the parking brake is released, or the transmission is not in park. 0781806 Display, Seat Belt Monitor, Cab
Overhead, Moved to LS Overhead
Panel

SEAT BELT DISPLAY IN CAB
The seat belt display in the cab will be located in the left side overhead switch panel per the switch panel layouts. An extension harness will be provided to allow the display to be relocated from the standard center location.

Bid #: 716 22
EXHIBIT 1 678
0890272 SP Intercom, David Clark, 4-Pos, 2-
Radio, (D,O,RPTT), 2C, U3805

INTERCOM SYSTEM
There will be a four (4) position David Clark, Model U3800, intercom system with single radio interface capability at the driver and officer positions and remote radio push to talk buttons located DRIVER: right of the PIC on the vertical surface. OFFICER: left of officer on vertical surface (both location per job 35227 01-03) SEE PHOTOS - SFD 05 & 06. Two (2) crew cab at one (1) rear facing seat and one (1) foward facing seat seats will have intercom only capability.

The following components will be provided:

One (1) U3805 Radio Cord Junction Module
Two (2) U3815 Radio interface modules (Driver, Officer) Two (2) Remote Push To Talk Button Kits
One (1) U3800 Master station (1 Crew)
One (1) U3801 Remote headset intercom station (1 Crew)
One (1) C3820 Power cord
All necessary station cables and connectors
0637058 David Clark Universal Radio
Interfaces Included with Single/Dual
System

RADIO / INTERCOM INTERFACE INCLUDED
All radio interfaced stations will have universal radio interfaces installed. The interface wiring will be routed within the cab to the left side rear facing compartment (option 0771803) . 0616382 Install Customer Provided
GPS/Multimode Antenna(s)

GPS / MULTIMODE ANTENNA INSTALLATION
There will be two (2) customer supplied GPS / Multimode antenna(s) with stud mount for thick roof material to be installed on the roof. The antenna coax cable(s) will be run per the packing list / instructions provided to the third party installer.

Specific shipping requirements will be followed. The GPS / Multimode antenna will be sent to the apparatus manufacturers preferred installer prior to cab fabrication. 0653533 Camera, Pierce, 7" LCD, Rear
Camera Only

VEHICLE CAMERA SYSTEM
There will be a color vehicle camera system provided with the following:

One (1) camera located at the rear of the apparatus, pointing rearward, displayed automatically with the vehicle in reverse.

The camera image will be displayed on a 7.00" LCD display located in view of the driver in the custom dash, per instrument panel layout. The display will include manual camera activation capability and audio from the active camera.

The following components will be included:

One (1) MO700136DC, display
One (1) SV-CW134639CAI, camera
All necessary cables
0523921 Recess, Rear Vision Camera RECESS REAR CAMERA
A rear camera recess will be provided in the center at the rear .

Bid #: 716 23
EXHIBIT 1 679
0624241 Electrical Power/Signal Protection &
Control, Enforcer

ELECTRICAL POWER CONTROL SYSTEM
A compartment will be provided in or under the cab to house the vehicle's electrical power and signal circuit protection and control components. The power and signal protection and control compartment will contain circuit protection devices and power control devices. Power and signal protection and control components will be protected against corrosion, excessive heat, excessive vibration, physical damage and water spray.

Serviceable components will be readily accessible.

Circuit protection devices, which conform to SAE standard, will be utilized to protect each circuit.

All circuit protection devices will be sized to prevent wire and component damage when subjected to extreme current overload. General protection circuit breakers will be Type-I automatic reset (continuously resetting) and conform to SAE J553 or J258. When required, automotive type fuses conforming to SAE J554, J1284, J1888 or J2077 will be utilized to protect electronic equipment.

Power control relays and solenoids will have a direct current (dc) rating of 125 percent of the maximum current for which the circuit is protected.

Visual status indicators will be supplied to identify control safety interlocks and vehicle status. In addition to visual status indicators, audible alarms designed to provide early warning of problems before they become critical will be used.

Voltage Monitor System
A voltage monitor system will be provided to indicate the status of each battery system connected to the vehicle's electrical load. The monitor system will provide visual and audio warning when the system voltage is above or below optimum levels.

Power and Ground Studs
Spare circuits will be provided in the primary distribution center for two-way radio equipment.

The spare circuits will consist of the following:

One (1) 12-volt DC, 30 amp battery direct spare
One (1) 12-volt DC ground and un-fused switched battery stud located in or adjacent to the power distribution center
EMI/RFI Protection
The electrical system proposed will include means to control undesired electromagnetic and radio frequency emissions. State of the art electrical system design and components will be used to ensure radiated and conducted EMI (electromagnetic interference) and RFI (radio frequency interference) emissions are suppressed at their source.

The apparatus proposed will have the ability to operate in the electromagnetic environment typically found in fire ground operations. The contractor will be able to demonstrate the EMI and RFI testing has been done on similar apparatus and certifies that the vehicle proposed meets SAE J551 requirements.

EMI/RFI susceptibility will be controlled by applying immune circuit designs, shielding, twisted pair wiring and filtering. The electrical system will be designed for full compatibility with low level control signals and high powered two-way radio communication systems. Harness and cable routing will be given careful attention to minimize the potential for conducting and radiated EMIRFI susceptibility. 0624256 Electrical System, Enforcer Hard
Wired

ELECTRICAL
All 12-volt electrical equipment installed by Pierce Manufacturing will conform to modern automotive practices. All wiring will be high temperature crosslink type. Wiring will be run, in loom or conduit, where exposed and have grommets where wire passes through sheet metal.

Automatic reset circuit breakers will be provided which conform to SAE Standards. Wiring will be color, function and number coded. Function and number codes will be continuously imprinted on all wiring harness conductors at 2.00" intervals. Exterior exposed wire connectors will be positive locking, and environmentally sealed to withstand elements such as temperature extremes, moisture and automotive fluids.

Electrical wiring and equipment will be installed utilizing the following guidelines:

All holes made in the roof will be caulked with silicon. Large fender washers, liberally caulked, will be used when fastening equipment to the underside of the cab roof.

Any electrical component that is installed in an exposed area will be mounted in a manner that will not allow moisture to accumulate in it. Exposed area will be defined as any location outside of the cab or body.

Electrical components designed to be removed for maintenance will not be fastened with nuts and bolts. Metal screws will be used in mounting these devices. Also, a coil of wire will be provided behind the appliance to allow them to be pulled away from mounting area for inspection and service work.

Corrosion preventative compound will be applied to all terminal plugs located outside of the cab or body. All non-waterproof connections will have this compound in the plug to prevent corrosion and for easy separation (of the plug).

All lights that have their sockets in a weather exposed area will have corrosion preventative compound added to the socket terminal area.

All electrical terminals in exposed areas will have silicon (1890) applied completely over the metal portion of the terminal.

All lights and reflectors, required to comply with Federal Motor Vehicle Safety Standard #108, will be furnished. Rear identification lights will be recessed mounted for protection.

Lights and wiring mounted in the rear bulkheads will be protected from damage by installing a false bulkhead inside the rear compartments.

An operational test will be conducted to ensure that any equipment that is permanently attached to the electrical system is properly connected and in working order.

The results of the tests will be recorded and provided to the purchaser at time of delivery.

Bid #: 716 24
EXHIBIT 1 680
0079196 Batteries, (4) Exide Grp 31, 950 CCA
ea, (1) Iso Bat, Threaded Stud

BATTERY SYSTEM
Four (4) 12 volt, Exide, Model 31S950X3W, group 31 batteries that include the following features will be provided:
950 CCA, cold cranking amps
190 amp reserve capacity
High cycle
Rating of 3800 CCA at 0 degrees Fahrenheit
760 minutes of reserve capacity
Threaded stainless steel studs
Each battery case will be a black polypropylene material with a vertically ribbed container for increased vibration resistance. The cover will be manifold vented with a central venting location to allow a 45 degree tilt capacity.

The inside of each battery will consist of a "maintenance free" grid construction with poly wrapped separators and a flooded epoxy bottom anchoring for maximum vibration resistance.

ISOLATED BATTERY
One (1) 12 volt, Exide, Model 31S950X3W, battery will be provided for voltage sensitive components. A battery isolator appropriately suited for the battery capacity will be supplied. 0008621 Battery System, Single Start, All
Custom Chassis

BATTERY SYSTEM
There will be a single starting system with an ignition switch and starter button provided and located on the cab instrument panel.

MASTER BATTERY SWITCH
There will be a master battery switch provided within the cab within easy reach of the driver to activate the battery system.

An indicator light will be provided on the instrument panel to notify the driver of the status of the battery system.
0002698 Battery Compartment,
Saber/Enforcer

BATTERY COMPARTMENTS
Batteries will be placed on non-corrosive mats and stored in well ventilated compartments located under the cab.

Heavy-duty, 2/0 gauge, color coded battery cables will be provided. Battery terminal connections will be coated with anti-corrosion compound.

Battery solenoid terminal connections will be encapsulated with semi-permanent rubberized compound.

JUMPER STUDS
One (1) set of battery jumper studs with plastic color-coded covers will be included on the battery compartments.
0756292 Charger, Sngl Sys, Kussmaul, 1200
PLC, 091-187-12-Remote, Ind Fet
40Amp

BATTERY CHARGER
There will be a Kussmaul™ 1200 PLC, product code 091-187-12-Remote (Gen 2), 40 amp battery charger provided with bar graph indicator.

The battery charger will be wired to the AC shoreline inlet through a receptacle adjacent to the battery charger.
0688318 Location, Charger, Cab Behind Driver
Seat, On the EMS Compt Vertical
Wall
Battery charger will be located in the cab behind the driver seat, on the vertical wall of the EMS compartment.
0536099 Location, Bat Chrg Ind, Driver's Step
Area
The battery charger indicator will be located in the driver's step area. 0016848 Shoreline, 20A 120V, Kussmaul Auto
Eject 091-20WP-120

KUSSMAUL AUTO EJECT FOR SHORELINE
There will be one (1) Kussmaul Model 091-20WP-120, 20 amp 120 volt AC shoreline inlet(s) provided to operate the dedicated 120 volt AC circuits on the apparatus.

The shoreline inlet(s) will include red weatherproof flip up cover(s).

There will be a release solenoid wired to the vehicle's starter to eject the AC connector when the engine is starting.

The shoreline(s) will be connected to battery charger.

There will be a mating connector body supplied with the loose equipment.

There will be a label installed near the inlet(s) that state the following:

Line Voltage
Current Ratting (amps)
Phase
Frequency
0026800 Shoreline Location

The shoreline receptacle will be located in the driver side lower step well of cab. 0121711 Alternator, 320 amp, Leece-Neville
4962PA, Sgl Sys

ALTERNATOR
A Leece-Neville, Model 4962PA, alternator will be provided. It will have a rated output current of 320 amps, as measured by SAE method J56. The alternator will feature an integral, self diagnostic regulator and rectifier. The alternator will be connected to the power and ground distribution system with heavy-duty cables sized to carry the full rated alternator output.

Bid #: 716 25
EXHIBIT 1 681
0644176 Load Manager, Integrated In
Electrical System, Saber FR/Enforcer

ELECTRONIC LOAD MANAGEMENT
An electronic load management (ELM) system that monitors the vehicles 12-volt electrical system, and automatically reduces the electrical load in the event of a low voltage condition and by doing so, ensures the integrity of the electrical system.

The ELM will monitor the vehicle's voltage while at the scene (parking brake applied). It will sequentially shut down individual electrical loads when the system voltage drops below a preset value. Two (2) separate electrical loads will be controlled by the load manager. The ELM will sequentially re-energize electrical loads as the system voltage recovers. 0780484 Headlights, Rect LED, HiViz FT-4X6-
4KIT, AXT/DCF/Enf/Imp/Sab/Vel

HEADLIGHTS
There will be a HiViz part number FT-4X6-4KIT, that includes four (4) 4.00" high x 6.00" long rectangular LED lights with parking lamp illumination around the outside of the lamps mounted in the front quad style, chrome housing on each side of the cab grille:
the outside lamp on each side will contain a part number FT-4X6-HL with low beam LEDs the inside lamp on each side will contain a part number FT-4X6-H with high beam LEDs the lights will be controlled through the headlight switch 0802935 Light, Directional, Wln M62T* LED,
Cmn Bzl, Above Headlights, Sab/Enf

FRONT DIRECTIONALS
The front directional's will be Whelen®, Model M62T, 4.31" high x 6.75" wide x 1.37" deep directional lights with amber LEDs. The lens color(s) to be the same as the LEDs. The directional's will be housed in the same common bezel as the front warning light and will be located above the headlights. The housing to be polished and the trim shall be chrome.

The flash pattern of the directional lights will be Steady On (Arrow). 0620054 Light, Directional/Marker,
Intermediate, Weldon 9186-8580-29
LED 2lts

INTERMEDIATE LIGHT
There will be two (2) Weldon, Model 9186-8580-29, amber LED turn signal marker lights furnished, one (1) each side, in the rear fender panel. The light will double as a turn signal and marker light.
0647802 Lights, Clearance/Marker/ID, Front,
P25 LED 5 Lts, Saber FR/Enforcer

CAB CLEARANCE/MARKER/ID LIGHTS
There will be five (5) amber LED lights provided to indicate the presence and overall width of the vehicle in the following locations:

Three (3) amber LED identification lights will be installed in the center of the cab above the windshield.

Two (2) amber LED clearance lights will be installed, one (1) on each outboard side of the cab above the windshield.
0647899 Lights, Directional/Marker, Cab Front
Side, Weldon 9186-8580-29 LED,
Sab/Enf

FRONT CAB SIDE DIRECTIONAL/MARKER LIGHTS
There will be two (2) Weldon, Model 9186-8580-29, amber LED lights installed front of the cab door, one (1) on each side of the cab.

The lights will activate as marker lights with the headlight switch and directional lights with the corresponding directional circuit.
0088869 Lights, Clearance/Marker/ID, Rear,
Truck-Lite 26250R LED 7Lts

REAR CLEARANCE/MARKER/ID LIGHTING
There will be three (3) Truck-Lite®, Model 26250R, LED lights used as identification lights located at the rear of the apparatus per the following:

As close as practical to the vertical centerline
Centers spaced not less than 6.00" or more than 12.00" apart Red in color
All at the same height
There will be two (2) Truck-Lite, Model 26250R, LED lights installed at the rear of the apparatus used as clearance lights located at the rear of the apparatus per the following:

To indicate the overall width of the vehicle
One (1) each side of the vertical centerline
As near the top as practical
Red in color
To be visible from the rear
All at the same height
There will be two (2) Truck-Lite, Model 26250R, LED lights installed on the side of the apparatus as marker lights as close to the rear as practical per the following:

To indicate the overall length of the vehicle
One (1) each side of the vertical centerline
As near the top as practical
Red in color
To be visible from the side
All at the same height
There will be two (2) red reflectors located on the rear of the truck facing to the rear. One (1) each side, as far to the outside as practical, at a minimum of 15.00", but no more than 60.00", above the ground.

There will be two (2) red reflectors located on the side of the truck facing to the side. One (1) each side, as far to the rear as practical, at a minimum of 15.00", but no more than 60.00", above the ground.

Per FMVSS 108 and CMVSS 108 requirements.

Bid #: 716 26
EXHIBIT 1 682
0804514 Lights, Tail, Wln M62BTT* Red
Stop/Tail & M62T* Amber Dir Arw For
Hsg

REAR FMVSS LIGHTING
The rear stop/tail and directional lighting included in the rear tail light housing will include the following:

Two (2) Whelen®, Model M62BTT, 4.30" high x 6.70" wide x 1.40" deep brake/tail lights with red LEDs
Two (2) Whelen, Model M62T, 4.30" high x 6.70" wide x 1.40" deep directional lights with amber LEDs. The directional lights will be set to Steady On (Arrow) flash pattern.

The lens color(s) to be clear.
0561471 Lights, Backup, Wln M6BUW, LED,
For Tail Lt Housing
There will be two (2) Whelen Model M6BUW, LED backup lights provided in the tail light housing. 0664481 Bracket, License Plate & Light, P25
LED

LICENSE PLATE BRACKET
There will be one (1) license plate bracket mounted on the rear of the body.

A white LED light will illuminate the license plate. A stainless steel light shield will be provided over the light that will direct illumination downward, preventing white light to the rear. 0556842 Bezels, Wln, (2) M6 Chrome Pierce,
For mtg (4) Wln M6 lights

LIGHTING BEZEL
There will be two (2) Whelen, Model M6FCV4P, four (4) place chromed ABS housings with Pierce logos provided for the rear M6 series stop/tail, directional, back up, scene lights or warning lights. 0589905 Alarm, Back-up Warning, PRECO
1040

BACK-UP ALARM
A PRECO, Model 1040, solid-state electronic audible back-up alarm that actuates when the truck is shifted into reverse will be provided. The device will sound at 60 pulses per minute and automatically adjust its volume to maintain a minimum ten (10) dBA above surrounding environmental noise levels.
0626588 Lights, Perimeter Cab, TecNiq T10-
LC00-1 15" LED 4Dr

CAB PERIMETER SCENE LIGHTS
There will be four (4) TecNiq, Model T10-LC00-1, 15.00" lights with white LEDs and 45 degree stainless steel brackets provided per the following:
one (1) under the driver's side cab access step
one (1) under the passenger's side cab access step
one (1) under the passenger's side crew cab access step one (1) under the driver's side crew cab access step
The lights will be activated when the battery switch is on, when the respective door is open and by the same control selected for the body perimeter lights. 0617901 Lights, Perimeter Pump House,
TecNiq T10-LC00-1 15" LED 2lts

PUMP HOUSE PERIMETER LIGHTS
There will be two (2) TecNiq, Model T10-LC00-1, 15.00" white 12 volt DC LED weatherproof strip lights provided under the pump panel running boards, one (1) each side.

The lights will be controlled by the same means as the body perimeter lights. 0626579 Lights, Perimeter Body, TecNiq T10-
LC00-1 15" LED 2lts, Rear Step

BODY PERIMETER SCENE LIGHTS
There will be two (2) TecNiq, Model T10-LC00-1, 15.00" 12 volt DC LED strip lights provided at the rear step area of the body, one (1) each side shining to the rear.

The perimeter scene lights will be activated when the parking brake is applied. 0566799 Lights, Step, P25 LED 4lts, Ign, Prk
Brk Activated

STEP LIGHTS
There will be four (4) white LED, step lights provided. One (1) step light will be provided on each side, on the front compartment face and two (2) step lights at the rear to illuminate the tailboard.

In order to ensure exceptional illumination, each light will provide a minimum of 25 foot-candles (fc) covering an entire 15" x 15" square placed ten (10) inches below the light and a minimum of

1.5 fc covering an entire 30" x 30" square at the same ten (10) inch distance below the light.

These step lights will be actuated when the ignition switch is on and the parking brake is set.

All other steps on the apparatus will be illuminated per the current edition of NFPA 1901. 0618301 Light, Visor, FRC, 12V SPA851-Q15-
*, LED 1st
12 VOLT LIGHTING
There will be one (1) Fire Research, Model SPA851-Q15-*, 12 volt LED floodlight(s) provided on the front visor, centered.

The housing(s) painted parts of this light assembly to be white with a white bezel.

The light(s) will be controlled in the following way:
a switch at the driver's side switch panel
a switch at the pump operator's panel
no additional switch location
These lights may be load managed when the parking brake is applied.

Bid #: 716 27
EXHIBIT 1 683
0772035 Lights, FRC, SPA***-Q15, 15,000
Lum, 12 VDC, 2nd
12 VOLT DC SCENE LIGHTS
There will be one (1) Fire Research Model SPA***-Q15, 15,000 lumens 12 volt DC powered lights with white LEDs installed on the apparatus located on the cab, right side rear of cab positioned so the light head faces out and is just above the cab roof.

The light(s) will be installed on vertical surface mount push-up pole(s) and to be connected to the Do Not Move Truck Indicator circuit.

The painted parts of this light assembly to be white with a white bezel.

The lights will be activated by a switch at the driver's side switch panel and by a switch at the left side pump panel.

The light(s) may be load managed when the parking brake is applied. 0772040 Lights, FRC, SPA***-Q15, 15,000
Lum, 12 VDC, 1st
12 VOLT DC SCENE LIGHTS
There will be one (1) Fire Research Model SPA***-Q15, 15,000 lumens 12 volt DC powered lights with white LEDs installed on the apparatus located on the cab, left side rear of cab positioned so the light head faces out and is just above the cab roof.

The light(s) will be installed on vertical surface mount push-up pole(s) and to be connected to the Do Not Move Truck Indicator circuit.

The painted parts of this light assembly to be white with a white bezel.

The lights will be activated by a switch at the driver's side switch panel and by a switch at the left side pump panel.

The light(s) may be load managed when the parking brake is applied. 0532358 Not Required, Deck Lights, Other
Hose Bed & Rear Lighting

0768474 Lights, Hose Bed, Below Alum Cvr,
Amdor AY-LB-12HW040, 40" LED 4lts

LIGHTS BELOW HOSE BED COVER
There will be four (4) Amdor Model AY-LB-12HW040, 700 lumens, 40.00" white LED lights provided to illuminate the hose bed area.

Two (2) LED light strips will be installed on the driver's side hose bed cover 30.00" from the front and rear of the hose bed, as close to the hinge as practical.

Two (2) LED light strips will be installed on the passenger's side hose bed cover 30.00" from the front and rear of the hose bed, as close to the hinge as practical.

The lights will be activated when the battery switch is on, and when the hosebed cover is raised. 0645677 Lights, Not Required, Rear Work, Alt.
12 Volt Lights At Rear Body
0787447 Lights, Walk Surf, Dual LED Light
Strips, Cargo Area, Bdy Stp Lt

WALKING SURFACE LIGHTS
There will be white 12 volt DC LED light strips with stainless steel protective cover, provided to light the cargo area.

One (1) light strip will be installed the entire length of the driver's side of the cargo area.

One (1) light strip will be installed the entire length of the passenger's side of the cargo area.

The light will be activated when the body step lights are on. 0060115 Pumper, Medium, Aluminum, 2nd
Gen
0554271 Body Skirt Height, 20"

Bid #: 716 28
EXHIBIT 1 684
0024469 SP Tank, Water, 700 Gallon, Poly, Med,
New York Style

WATER TANK
Booster tank will have a capacity of 700 gallons and be constructed of polypropylene plastic by United Plastic Fabricating, Incorporated.

The tank will be forward of the hosebed, to achieve a very low hosebed area to the rear of the water tank.

Tank joints and seams will be nitrogen welded inside and out.

Tank will be baffled in accordance with NFPA Bulletin 1901 requirements.

Baffles will have vent openings at both the top and bottom to permit movement of air and water between compartments.

Longitudinal partitions will be constructed of .38" polypropylene plastic and will extend from the bottom of the tank through the top cover to allow for positive welding.

Transverse partitions will extend from 4.00" off the bottom of the tank to the underside of the top cover.

All partitions will interlock and will be welded to the tank bottom and sides.

Tank top will be constructed of .50" polypropylene. It will be recessed .38" and will be welded to the tank sides and the longitudinal partitions.

Tank top will be sufficiently supported to keep it rigid during fast filling conditions.

Construction will include 2.00" polypropylene dowels spaced no more than 30.00" apart and welded to the transverse partitions. Two (2) of the dowels will be drilled and tapped (.50" diameter, 13.00" deep) to accommodate lifting eyes.

A sump that will be sized dependent on the tank to pump plumbing will be provided at the bottom of the water tank.

Sump will include a drain plug and the tank outlet.

Tank will be installed in a fabricated cradle assembly constructed of structural steel.

Sufficient crossmembers will be provided to properly support bottom of tank. Crossmembers will be constructed of steel bar channel or rectangular tubing.

Tank will "float" in cradle to avoid torsional stress caused by chassis frame flexing. Rubber cushions, .50" thick x 3.00" wide, will be placed on all horizontal surfaces that the tank rests on.

Stops or other provision will be provided to prevent an empty tank from bouncing excessively while moving vehicle.

Mounting system will be approved by the tank manufacturer. 0003405 Overflow, 4.00" Water Tank, Poly

Fill tower will be constructed of .50" polypropylene and will be a minimum of 8.00" wide x 14.00" long.

Fill tower will be furnished with a .25" thick polypropylene screen and a hinged cover.

An overflow pipe, constructed of 4.00" schedule 40 polypropylene, will be installed approximately halfway down the fill tower and extend through the water tank and exit to the rear of the rear axle. 0028104 Foam Cell Required
0023412 Drain, Tank - 1.50" TANK DRAIN
A 1.50" tank drain will be installed with a 1.50" ball valve located underneath the left front compartment and properly labeled.
0662467 Modified Poly Tank, Raised Tee, One
Side
0084432 Modified Poly Tank, Ext'd Over Rear
Compt
The water tank will be extended to the rear of the truck, over the rear compartment. 0553725 Restraint, Water Tank, Heavy Duty,
Special Type Tank, 4x4, or Export

WATER TANK RESTRAINT
A heavy-duty water tank restraint will be provided.
0003429 Not Required, Direct Tank Fill

0003424 Not Required, Dump Valve

0048710 Not Required, Jet Assist

0030007 Not Required, Dump Valve Chute

0514778 Not Required, Switch, Tank Dump
Master
Bid #: 716 29
EXHIBIT 1 685
0556223 Hose Bed, Aluminum, Pumper, New
York Style, Fill In Blank Height,
Painted

HOSE BED
The hose bed will be fabricated of 0.125"-5052 aluminum with a nominal 38,000 psi tensile strength.

The hose bed will be as low as practical.

Upper and rear edges of side panels will have a double break for rigidity.

Any area of the outboard hose bed wall that extends past the end of the hose bed floor will be covered with brushed stainless steel to prevent damage to painted surface when hose is removed.

Flooring of the hose bed will be removable aluminum grating with the top surface corrugated to aid in hose aeration. The grating slats will be a minimum of 0.50" x 4.50" with spacing between slats for hose ventilation.

A cross divider will be provided at the front of the hose bed before the tank transitions from the lower section to the upper section. The divider will run from the top of the side sheet down below the hose bed grating.

The hose bed floor will be MAXIMUM of 6'-6.00" (78.00") UNLOADED" from the ground when the truck is fully loaded.
0723549 Painted Hose Bed

The hose bed interior walls will be painted to match the lower body color. 0003481 Hose Bed Capacity, Special

Hose bed will accommodate (DS to PS): 800' x 5.00" | 500' x 2.50" | 500' x 2.50". Hosebed dimensions are to be 68.00" wide x 109.00" deep to cross divider x 22.00" high (hosebed floor to top of side sheet). LAYOUT HOSEBED TO DIMENSIONS STATED, NOT TO HOSE CAPACITY!. 0680455 Divider, Hose Bed, .25" Unpainted,
(6) Bolts

HOSE BED DIVIDER
Two (2) hosebed dividers will be furnished for separating hose.

Each divider will be constructed of a .25" brushed aluminum sheet.

Partition will be fully adjustable by sliding in tracks, located at the front and rear of the hose bed.

Divider will be held in place by tightening six (6) bolts in (3) locations. Two (2) bolts at the front of the divider, two (2) bolts at the back of the divider and two (2) bolts in the middle of the divider.

Acorn nuts will be installed on all bolts in the hose bed which have exposed threads.

Flat surfaces will be sanded for uniform appearance, or constructed of brushed aluminum. 0010133 Cross-Divider, Hose Bed

A cross-divider will be provided just behind the fill tower. The divider will be bolted to the side sheet.
0581892 Divider, Hose Bed, .25" Sheet,
Unpainted, Permanent

There will be one (1) additional hose bed dividers furnished.

Each divider will be constructed of a .25" brushed aluminum sheet.

Partition will be permanently installed and located above the ladder storage and attached to backboard trough. To run full length of hose bed and connect to cross divider.

Acorn nuts will be installed on all bolts in the hose bed which have exposed threads.

Flat surfaces will be sanded for uniform appearance or constructed of brushed aluminum. 0729492 Cover, Hose Bed, Alum Treadplate,
Bolted T-Bar, Electric Actuated

HOSE BED COVER ELECTRIC ACTUATOR
A two (2) section hose bed cover, constructed of .125" bright aluminum treadplate will be furnished. The cover will be hinged with full length stainless steel piano hinge. The sides will be slanted down with the center of the cover supported by a modular stationary bridgework support.

The covers will not over lap.

The cover will be reinforced so that it can support the weight of a man walking on the cover.

A pneumatic gas spring assist will be installed at the front of the covers to help support and stabilize the cover throughout its range of motion.

If access to water tank fill tower is blocked by the hose bed cover, then a hinged door will be provided in it so that tank may be filled without raising cover doors.

Chrome grab handles and two (2) (one (1) each side) electric linear actuator with brake cylinders will be provided to assist in opening and closing the cover. A rubber-covered momentary toggle switch will be provided for each actuator that controls the opening and closing of the covers. Each switch will be located at the rear body of the body at the left side. Additional locks on top of the cover are not required to secure the cover in the nested position.

A cross divider will be provided directly behind the actuators, at the front of the hose bed, to support the actuators and provide a clean appearance.

A handrail will be provided at the rear, in the center of the support, to assist in climbing up the back of the truck.

The hose bed cover will be connected to the Do Not Move Truck indicator. The light will be activated if the cover is not in the stowed position and the parking brake is released. 0587696 Hose Restraint, Hose Bed,One Piece
Vinyl Flap,Strap Fastener,Hose Bed
Frame,Rear

HOSEBED RESTRAINT REAR
There will be a red vinyl flap installed at the rear of the hosebed. The flap will be attached to the top hosebed frame with quarter turn fasteners. The flap will have straps that loop through footman loops at the bottom of the hosebed and fasten with spring clip and hook fasteners and chain.

Bid #: 716 30
EXHIBIT 1 686
0013512 Running Boards, 12.75" Deep

RUNNING BOARDS
Running boards will be fabricated of .125" bright aluminum treadplate.

Each running board will be supported by a welded 2.00" square tubing and channel assembly, which will be bolted to the pump compartment substructure.

Running boards will be 12.75" deep and spaced .50" away from the pump panel.

A splash guard will be provided above the running board treadplate. 0678630 SP Tailboard, T-Shaped, 20" & 4" (NonStep) Deep, Ang Corners TAILBOARD The tailboard will also be constructed of .125" bright aluminum treadplate and spaced .50" from the body, as well as supported by a structural steel assembly.

The tailboard area will be 20.00" deep in the center area and 4.00" deep to the rear of the side compartments. The tailboard will be T-shaped. The 4.00" extension to the rear of the side compartments will be angled up to prevent this area from being used as a stepping surface.

The outboard sides of the tailboard will be angled at 45 degrees beginning at the point where the body meets the tailboard at the forward outboard edge angling rearward to the rear edge of the tailboard.

The exterior side will be flanged down and in for increased rigidity of tailboard structure. 0690037 Wall, Rear, Smooth Aluminum/Body
Material

REAR WALL, SMOOTH ALUMINUM/BODY MATERIAL
The rear facing surfaces of the center rear wall will be smooth aluminum.

The bulkheads, the surface to the rear of the side body compartments, will be smooth and the same material as the body.

Any inboard facing surfaces below the height of the hosebed will be aluminum diamondplate. 0889214 Tow Eyes, w/Tow Bar, 2G Pumper

REAR TOW EYES
Two (2) tow eyes, which are an integral part of the body mounting substructure, will be installed below the rear of the truck.

The tow eyes will be of adequate strength to allow the truck to be pulled from the eyes.

REAR TOW BAR
One (1) tow bar will be installed under the tailboard, 3.00" forward from the rear of the tailboard.

With air ride suspension and a 65 gallon fuel tank, the tow bar will be located .50" further rearward than normal when there is this combination of options.

The tow bar assembly will be designed and positioned to allow up to a 30-degree upward angled pull of 17,000 lb, or a 20,000 lb straight horizontal pull in line with the centerline of the vehicle.

The tow bar design will have been tested and evaluated using finite element analysis techniques. 0590926 Hose Restraint, Running Board,
Velcro Straps

RUNNING BOARD HOSE RESTRAINT
A pair of 2.00" wide black nylon straps with Velcro fasteners will be provided for each hose tray to secure the hose during travel. There will be Two (2) hose trays located one (1) in each side running board.
0014123 Tray, Hose, Running Board, Special
Capacity, FITB

HOSE TRAY
Two (2) hose trays will be recessed one (1) in each side running board.

Capacity of the tray will be 48"L x 9"W x 9"D.

Rubber matting will be installed on the floor of the tray to provide proper ventilation. Drain holes will be provided.

Bid #: 716 31
EXHIBIT 1 687
0895820 Construction, Compt, Alum, 2G
Pumper

COMPARTMENTATION
Body and compartments will be fabricated of 0.125", 5052-H32 aluminum.

Side compartments will be an integral assembly with the rear fenders.

Circular fender liners will be provided for prevention of rust pockets and ease of maintenance.

Side compartment flooring will be of the sweep out design with the floor higher than the compartment door lip.

The side compartment door opening will be framed by flanging the edges in 1.75" and bending out again 0.75" to form an angle.

Drip protection will be provided above the doors by means of bright aluminum extrusion, formed bright aluminum treadplate or polished stainless steel.

The top of the compartment will be covered with bright aluminum treadplate rolled over the edges on the front, rear and outward side. These covers will have the corners welded.

Side compartment covers will be separate from the compartment tops.

Front facing compartment walls will be covered with bright aluminum treadplate.

All screws and bolts which protrude into a compartment will have acorn nuts on the ends to prevent injury.

UNDERBODY SUPPORT SYSTEM
Due to the severe loading requirements of this pumper a method of body and compartment support suitable for the intended load will be provided.

The backbone of the support system will be the chassis frame rails which is the strongest component of the chassis and is designed for sustaining maximum loads.

Forward to the rear axle, the support system will include "L"-shaped support members bolted to the chassis frame rails. These welded support members will include vertical formed channels, horizontal structural channels, and support gussets. These parts extend from the chassis frame outward underneath the body.

Rearward to the rear axle, the body support system will include two rearward facing "L"-shaped support members bolted to the chassis frame rails. These support members will be connected to the two body supporting crossmembers forming a boxed foundation for the rear body support system.

Steel upper platform decks will be mounted on the top of these support members to create a floating substructure which will result in a 500 lb equipment support rating per lower compartment.

All structural components of this system will be made from high strength 50K steel plate material or structural steel componentry. The steel frames as well as the steel vertical angles will be treated with an epoxy E-coat to provide resistance to corrosion and chemicals as standard.

The floating substructure will be separated from the horizontal members with neoprene elastomer isolators. These isolators will reduce the natural flex stress of the chassis from being transmitted to the body.

Isolators will have a broad load range, proven viability in vehicular applications, be of a fail-safe design and allow for all necessary movement in three (3) transitional and rotational modes.

The neoprene isolators will be installed in a pattern which assimilates a three (3)-point mounting pattern to reduce the natural flex of the chassis being transmitted to the body.

A design with body compartments hanging on the chassis in an unsupported fashion will not be acceptable.

AGGRESSIVE WALKING SURFACE
All exterior surfaces designated as stepping, standing, and walking areas will comply with the required average slip resistance of the current NFPA standards.

LOUVERS
Louvers will be stamped into compartment walls to provide the proper airflow inside the body compartments and to prevent water from dripping into the compartment. Where these louvers are provided, they will be formed into the metal and not added to the compartment as a separate plate.

TESTING OF BODY DESIGN
Body structural analysis will be fully tested. Proven engineering and test techniques such as finite element analysis, strain gauging, and model analysis will be performed with special attention given to fatigue, life and structural integrity of the body and substructure.

Body will be tested while loaded to its greatest in-service weight.

The criteria used during the testing procedure will include:

Raising opposite corners of the vehicle tires 9.00" to simulate the twisting a truck may experience when driving over a curb.

Making a 90 degree turn, while driving at 20 mph to simulate aggressive driving conditions.

Driving the vehicle at 35 mph on a washboard road.

Driving the vehicle at 55 mph on a smooth road.

Accelerating the vehicle fully, until reaching the approximate speed of 45 mph on rough pavement.

Evidence of actual testing techniques will be made available upon request.

Bid #: 716 32
EXHIBIT 1 688
0083610 LS 152" Lap, Full Height Front &
Rear

LEFT SIDE COMPARTMENTATION
The left side compartmentation will consist of three lap door compartments.

A full height, vertically hinged, single door compartment ahead of the rear wheels will be provided. The interior dimensions of this compartment will be 34.50" wide x 66.63" high x 25.88" deep in the lower 25.00" of the compartment and 12.00" deep in the remaining upper portion. The clear door opening will be a minimum of 28.63" wide x 61.88" high.

A horizontally hinged, single lift-up door compartment over the rear wheels will be provided. The interior dimensions of this compartment will be 66.50" wide x 32.88" high x 12.00" deep. The clear door opening will be a minimum of 59.25" wide x 27.00" high.

A full height, vertically hinged, double door compartment behind the rear wheels will be provided.The interior dimensions of this compartment will be 47.75" wide x 67.63" high x

12.00" deep. A section of this compartment will be 25.88" deep for the first 31.50" width x

26.00" height directly behind the rear wheels. The clear door opening will be a minimum of

43.50" wide x 62.88" high.

The interior height of the compartments will be measured from the compartment floor to the ceiling. The depth of the compartments will be measured from the back wall to the inside of the door frame.

Closing of the doors will not require releasing, unlocking, or unlatching any mechanism and will easily be accomplished with one hand.

The vertically hinged doors will be furnished with a positive door holder.

The lift-up door will be furnished with two gas-charged cylinders to assist in the opening of the door and to maintain the door in an open position. There will be a field adjustable, three-position bracket mounted on the vertical side door opening that will allow the door to be held open at 87°, 90°, or 93°.
0063624 RS 152" Lap, Full Height Front &
Rear, FDLER

RIGHT SIDE COMPARTMENTATION
The right side compartmentation will consist of three lap door compartments.

A full height, vertically hinged, single door compartment ahead of the rear wheels will be provided. The interior dimensions of this compartment will be 34.50" wide x 66.63" high x 25.88" deep in the lower 25.00" of the compartment and 12.00" deep in the remaining upper portion. The clear door opening will be a minimum of 28.63" wide x 61.88" high.

A horizontally hinged, single lift-up door compartment over the rear wheels will be provided. The interior dimensions of this compartment will be 66.50" wide x 32.88" high x 12.00" deep. The clear door opening will be a minimum of 59.25" wide x 27.00" high.

A full height, vertically hinged, double door compartment behind the rear wheels will be provided.The interior dimensions of this compartment will be 47.75" wide x 67.63" high x

25.88" deep in the lower 26.00" of the compartment and 12.00" deep in the remaining upper portion. The clear door opening will be a minimum of 43.50" wide x 62.88" high.

The interior height of the compartments will be measured from the compartment floor to the ceiling. The depth of the compartments will be measured from the back wall to the inside of the door frame.

Closing of the doors will not require releasing, unlocking, or unlatching any mechanism and will easily be accomplished with one hand.

The vertically hinged doors will be furnished with a positive door holder.

The lift-up door will be furnished with two gas-charged cylinders to assist in the opening of the door and to maintain the door in an open position. There will be a field adjustable, three-position bracket mounted on the vertical side door opening that will allow the door to be held open at 87°, 90°, or 93°.
0063911 Doors, Lap w/ "D" Handles - Side
Compartments

SIDE COMPARTMENT DOORS
All hinged compartment doors will be lap style with double panel construction and will be a minimum of 1.50" thick. The doors will be made out of the same material as the body. To provide additional door strength a "C" section reinforcement will be installed between the outer and interior panels.

Doors will be provided with a closed cell rubber gasket around the surface that laps onto the body. A second heavy-duty automotive rubber molding with a hollow core will be installed on the door framing that seals onto the interior panel, to ensure a weather resisting compartment.

All compartment doors will have polished stainless steel continuous hinge with a pin diameter of .25" that is bolted or screwed on with stainless steel fasteners. (Hinges which are welded on will not be acceptable.)
All door locking mechanisms will be fully enclosed within the door panels to prevent fouling of the lock in the event equipment inside shifts into the lock area.

Doors will be latched with recessed, polished stainless steel "D" ring handles and FMVSS approved door locking mechanisms.

To prevent corrosion caused by dissimilar metals, compartment door handles will not be attached to outer door panel with screws. A rubber gasket will be provided between the "D" ring handle and the door.
0013671 Compt, Rear, Rollup, 30.75" FF,

25.88" D

REAR COMPARTMENTATION
A roll-up door compartment above the rear tailboard will be provided.

The interior dimensions of this compartment will be 40.00" wide x 33.63" high x 25.88" deep. The spool of the rollup door at the top of the compartment takes up some usable space. The depth of the compartment will be calculated with the compartment door closed.

A louvered, removable access panel will be furnished on the back wall of the compartment.

The rear compartment will be open into the rear side compartments.

The clear door opening of this compartment will be a minimum of 33.25" wide x 23.88" high.

Closing of the door will not require releasing, unlocking, or unlatching any mechanism and will easily be accomplished with one hand.

Bid #: 716 33
EXHIBIT 1 689
0594003 Door, Amdor, Rollup, Rear
Compartment

ROLLUP REAR COMPARTMENT DOOR
The rear compartment will have a rollup door.

The door will be double faced, aluminum construction, painted one (1) color to match the upper portion of the body and manufactured by AMDOR™ brand rollup doors.

The door will be constructed using 1.00" extruded double wall aluminum slats which will feature a flat smooth interior surface to provide maximum protection against equipment hang-up. The slats will be connected with a structural driven ball and socket hinge designed to provide maximum curtain diaphragm strength. Mounting and adjusting the curtain will be done with a clip system that connects the curtain to the balancer drum allowing for easy tension adjustment without tools.

The slats will be mounted in reusable slat shoes with positive snap-lock securement.

Each slat will incorporate weather tight recessed dual durometer seals. One (1) fin will be designed to locate the seal within the extrusion. The second will serve as a wiping seal which will also allow for compression to prevent water ingression.

The door will be mounted in a one (1)-piece aluminum side frame with recessed side seals to minimize seal damage during equipment deployment. All seals including side frames, top gutters and bottom panel are to be manufactured utilizing non-marring materials.

Bottom panel flange of rollup door will be equipped with two (2) cut-outs to allow for easier access with gloved hands.

A polished stainless steel lift bar with locking key latches to be provided for each roll-up door. The keys to be Model 1250 for all compartment doors. The lift bar will be located at the bottom of door with striker latches installed at the base of the side frames. Side frame mounted door strikers will include support beneath the stainless steel lift bar to prevent door curtain bounce, improve bottom seal life expectancy and to avoid false door ajar signals.

All injection molded rollup door wear components will be constructed of Type 6 Nylon.

The door will have a 3.00 inch diameter balancer/tensioner drum to assist in lifting the door.

The header for the rollup door assembly will not exceed 4.00".

A heavy-duty magnetic switch will be used for control of open compartment door warning lights. 0554992 Body Modification, 5" Reduced Depth
Rear Compt

BODY MODIFICATION FROM STANDARD
The following body modifications will be required for the installation of a single axle air ride suspension:
- Rear compartment will be 5.00" shorter in depth.
- Special water tank mounting required if applicable.
0010414 Keyed Locks for Latches, Lap Doors,
Key Style 1250

KEYED LOCK(S)
There will be six (6) compartment doors furnished with a keyed lock. The compartmentation to have a keyed lock will be LS1, LS2, LS3, RS1, RS2 and RS3. 0731558 Pull Strap for Liftup Doors

LIFTUP DOOR PULL STRAPS
two (2) compartment doors will be provided with pull straps. The pull straps will be 12.00" long and black in color.

The straps will be installed directly to the inside of the liftup door.

The liftup door compartments to have these straps will be LS2 and RS2. 0003919 Reverse Hinge Compartment Door REVERSE HINGED DOOR The one (1) compartment door, located LS3, will have the hinge at the rear of the door. 0659353 Lights, Compt, Amdor AY-9220 LED,
Dual Lt Strip

COMPARTMENT LIGHTING
There will be seven (7) compartments with Amdor, Model AY-9220, white 12 volt DC LED compartment light strips. The lights will be mounted with mechanical fasteners.

There will be two (2) strip lights installed vertically in each compartment opening per the latest NFPA requirements.

The lights will be activated when the battery switch is on and the respective compartment door is opened.
0687135 Shelf Tracks, Unpainted

MOUNTING TRACKS
There will be five (5) sets of tracks for mounting shelf(s) in LS1, LS2, LS3, RS1 and RS3. These tracks will be installed vertically to support the adjustable shelf(s), and will be full height of the compartment. The tracks will be unpainted with a natural finish. 0600350 Shelves, Adj, 500 lb Capacity, Full
Width/Depth, Predefined Locations

ADJUSTABLE SHELVES
There will be nine (9) shelves with a capacity of 500 lb provided.

The shelf construction will consist of .188" aluminum with a dual action finish with 2.00" sides.

Each shelf will be infinitely adjustable by means of a threaded fastener, which slides in a track.

The shelves will be held in place by .12" thick stamped plated brackets and bolts.

The location(s) will be in RS3 in the upper third, in RS3 in the upper third, in RS1 in the upper third, in RS1 in the upper third, in LS2 centered between the floor and ceiling, in LS3 in the lower third, in LS3 in the upper third, in LS1 in the upper third and in LS3 at the depth transition point.

Bid #: 716 34
EXHIBIT 1 690
0709690 Tray, 250 lb Slide-out, 2" Sides - Adj.

Height, Predefined Locations

SLIDE-OUT ADJUSTABLE HEIGHT TRAY
There will be one (1) slide-out tray provided.

Each tray will have 2.00" high sides and a minimum capacity rating of 250 lb in the extended position.

Each tray will be constructed of aluminum with a dual action finish.

Each tray will be mounted on a pair of side mounted slides. The slide mechanisms will have ball bearings for ease of operation and years of dependable service. The slides will be mounted to shelf tracks to allow the tray to be adjustable up and down within the designated mounting location.

An automatic lock will be provided for both the in and out tray positions. The lock trip mechanism will be located at the front of the tray and will be easily operated with a gloved hand.

The location(s) will be in B1 centered between the floor and ceiling 0647045 Tray, Floor Mounted, Slide-Out, Full
Width/Full Depth, 500lb, 2.00" Sides,
2G

SLIDE-OUT FLOOR MOUNTED TRAY
There will be one (1) floor mounted slide-out tray(s) with 2.00" sides provided LS3. Each tray will be rated for up to 500lb in the extended position. The tray(s) will be constructed of a minimum .13" aluminum. The finish will be unpainted aluminum with a DA finish.

The trays will be designed for maximum compartment width and depth.

There will be two undermount-roller bearing type slides rated at 250lb each provided. The pair of slides will have a safety factor rating of 2.

To ensure years of dependable service, the slides will be coated with a finish that is tested to withstand a minimum of 1,000 hours of salt spray per ASTM B117.

To ensure years of easy operation, the slides will require no more than a 50lb force for push-in or pull-out movement when fully loaded after having been subjected to a 40 hour vibration (shaker) test under full load. The vibration drive file will have been generated from accelerometer data collected from a heavy truck chassis driven over rough gravel roads in an unloaded condition.

Proof of compliance will be provided upon request.

Automatic locks will be provided for both the "in" and "out" positions. The trip mechanism for the locks will be located at the front of the tray for ease of use with a gloved hand. 0595085 Toolboard, Swing-out, Alum, .188",
Pac Trac

SWING OUT TOOLBOARD
A swing out aluminum toolboard will be provided.

It will be a minimum of .188" thick aluminum.

Pac Trac tool mount material will be provided on both sides of the toolboard.

A 1.00" x 1.00" aluminum tube frame will be welded to the edge of the pegboard.

The board will be mounted on a pivoting device at the front of the compartment on the top and bottom to allow easy movement in and out of the compartment. The maximum tool load will be 400 pounds.

The board will have positive lock in the stowed and extended position.

The board will be mounted on adjustable tracks from front to back within the compartment.

There will be One (1) toolboard(s) provided and installed RS2. 0726441 Partition, Trans Rear Compt

PARTITION, TRANSVERSE REAR COMPARTMENT
Two (2) partitions will be bolted in place to separate the left and right side rear compartments from the rear tailboard compartment. The partition will be body material with a dual action finish. 0890103 SP Tray, 1" Sides, Fixed Floor Mount,
S/S, Unpainted, No Front Lip

FLOOR MOUNTED FIXED TRAY
There will be one (1) fixed floor mount tray with 1.00" sides and rear. There will be no front lip.

A capacity rating will not be available on this tray due to reduced side height being less than

2.00".

Tray location will be RS3.

The tray will be bolted to the floor of the compartment for a permanent mount. The tray will be constructed of stainless steel and unpainted.
0003934 Dust Filter, Compt Louvers

COMPARTMENT DUST FILTERS
A total of five (5) body compartment louvers will have a removable dust filter installed to restrict road dirt from easily entering the compartment and will be installed LS1, LS3, RS1, RS3 and B1. 0797957 Pac Trac, Installed on Compt Wall,
Back Wall Only

EQUIPMENT MOUNTING SYSTEM
Pac Trac equipment mounting system will be installed on the back wall of one (1) compartment (s), RS2.
0004016 Rub Rail, Aluminum Extruded, Side of
Body

RUB RAIL
Bottom edge of the side compartments will be trimmed with a bright aluminum extruded rub rail.

Trim will be 2.12" high with 1.38" flanges turned outward for rigidity.

The rub rails will not be an integral part of the body construction, which allows replacement in the event of damage.

Bid #: 716 35
EXHIBIT 1 691
0784811 Fender Crowns, Rear, Stainless,
w/Removable Liner

BODY FENDER CROWNS
Polished stainless steel fender crowns will be provided around the rear wheel openings with a dielectric barrier will be provided between the fender crown and the fender sheet metal to prevent corrosion.

The fender crowns will be held in place with stainless steel screws that thread directly into a composite nut and not directly into the parent body sheet metal to eliminate dissimilar metals contact and greatly reduce the chance for corrosion. Rubber welting will be provided between the body and crown.

BODY FENDER LINER
A painted to match the lower body color fender liner will be provided. The liners will be removable to aid in the maintenance of rear suspension components. 0602346 Hose, Hard Suction, Provided by
Dealer, Pumper NFPA 2016
Classification

HARD SUCTION HOSE PROVIDED BY DEALER
NFPA 1901, 2016 edition, section 5.8.2 requires a minimum of 20 ft of suction hose or 15 ft of supply hose.

Hose is not on the apparatus as manufactured. The dealer will provide suction or supply hose.

There will be Two (2) lengths of 10' long x6.00" diameter hose provided and equipped with a Long Handle Female and Rocker Lug Male couplings provided on the ends. The brand will be Kochek. 0004095 Troughs, H.S.H., (1) Each Side, Steel

HOSE TROUGHS
Hard suction hose will be carried in two (2) V-shaped troughs, one (1) each side, and held in place by chrome plated, quarter turn, spring loaded clamps.

Troughs will be constructed of steel and painted job color. 0626229 Handrails, Side Pump Panels, Per
Print

HANDRAILS
The handrails will be 1.25" diameter knurled aluminum to provide a positive gripping surface.

Chrome plated end stanchions will support the handrail. Plastic gaskets will be used between end stanchions and any painted surfaces.

Drain holes will be provided in the bottom of all vertically mounted handrails.

Handrails will be provided to meet NFPA 1901 section 15.8 requirements. The handrails will be installed as noted on the sales drawing.
0025450 Handrails, Rear Bulkhead

One (1) vertical handrail will be located on each rear bulkhead. 0004146 Handrail, Rear, Below Hose Bed, Full
Width

HANDRAIL
One (1) full width horizontal handrail will be provided below the hose bed at the rear of the apparatus.
0004150 Handrail, Extra - 15-20" Long

ADDITIONAL HANDRAIL
Two (2) handrails will be mounted on top of the left side sheet forward and on top of the right side sheet forward.
0636301 Compt, Extinguisher (2) Fender
Panel, Triangular Door

EXTINGUISHER/AIR BOTTLE/ STORAGE (Triangular)
A total of two (2) extinguisher/air bottle/storage compartments will be provided on the right side forward and aft of the rear wheels. The triangular shaped compartment will be sized to fit a 8.00" diameter extinguisher in the lower area and a 8.00" diameter extinguisher in the upper area. The compartment will be approximately 25.50" deep. A partition will be provided to separate the compartment. Also inside the compartment, black Dura-Surf friction reducing material will be provided. The compartment will be furnished with a drain hole. A brushed stainless steel, triangular shaped door with a chrome plated flush lift & turn latch will be provided to contain the air bottles. A dielectric barrier will be provided between the door hinge, hinge fasteners and the body sheet metal.

AIR BOTTLE COMPARTMENT STRAP
A strap will be provided in the air bottle compartment(s) to help contain the bottles when the vehicle is parked on an incline. The strap will wrap around the neck and attach to the wall of the compartment.
0654143 Compt, Air Bottle, Single,Tri Door
(DEF/Fuel), Fender Panel
AIR BOTTLE STORAGE (Single)
A quantity of one air bottle compartment, approximately 7.50" wide x 7.50" tall x 26.00" deep, will be provided on the driver side rearward of the rear wheels. The triangular door will cover the air bottle opening, the DEF tank access, and fuel fill. The compartment will be square with angled corners. A brushed stainless steel door with a chrome plated flush lift & turn latch will be provided to contain the air bottle. A dielectric barrier will be provided between the door hinge, hinge fasteners and the body sheet metal.

Inside the compartment, black Dura-Surf friction reducing material will be provided.

AIR BOTTLE COMPARTMENT STRAP
A strap will be provided in the air bottle compartment to help contain the air bottle when the vehicle is parked on an incline. The strap will wrap around the neck and attach to the wall of the compartment.

Bid #: 716 36
EXHIBIT 1 692
0657522 Compt, Air Bottle, Triple, Fender
Panel
AIR BOTTLE STORAGE (Triple)
A quantity of one (1) air bottle compartment designed to hold (3) air bottles up to 7.25" in diameter x 26.00" deep will be provided on the left side forward of the rear wheels. A brushed stainless steel door with a chrome plated flush lift & turn latch will be provided to contain the air bottle. A dielectric barrier will be provided between the door hinge, hinge fasteners and the body sheet metal.

Inside the compartment, black Dura-Surf friction reducing material will be provided.

AIR BOTTLE COMPARTMENT STRAP
A strap will be provided in the air bottle compartment(s) to help contain the air bottles when the vehicle is parked on an incline. The strap will wrap around the neck and attach to the wall of the compartment.
0004225 Ladder, 24' Duo-Safety 900A 2-
Section

EXTENSION LADDER
There will be a 24' two-section aluminum Duo-Safety Series 900-A extension ladder provided. 0004230 Ladder, 14' Duo-Safety 775A Roof ROOF LADDER
There will be a 14' aluminum Duo-Safety Series 775-A roof ladder provided. 0730790 SP Ladders Btwn Tank & S.Sht, RS,
Ext'd Rr, Encl'd Complete, RPH,
Vinyl, Spcl Mnt

LADDER STORAGE
The ladders will be stored between the water tank and the right side compartments.

The ladders will extend into the pump compartment just to the rear of the water pump discharges.

The ladder storage area will be enclosed as practical by means of sheet metal to protect the ladders from road dirt. The ladders that extend into the pump house will also be enclosed with vinyl. A black rubber boot will be provided to enclosed the ladders in the gap between the pump house and the body.

Each ladder will be stored vertically in a separate stainless steel storage trough. Each stainless steel trough will be lined with Dura-Surf nylon slides.

The ladders will be mounted with the fly section pointed inboard towards the water tank.

A bright aluminum treadplate enclosure will be provided at the rear of the body to properly contain the ladders This enclosure will extend to the rear of the side body compartments.

The enclosure will also include a vertically hinged smooth aluminum door with a D-handle latch to access the ladders.
0733387 Ladder, 10' Duo-Safety Folding 585A

FOLDING LADDER
One (1) 10.00' aluminum, Series 585-A, Duo-Safety folding ladder will be installed. 0733796 Trough, Folding Ladder, Ladder
Storage Btwn Tank & S.Sht

FOLDING LADDER STORAGE
There will be storage designated left side for folding ladders stored between the side sheet in a stainless steel trough in the ladder storage compartment. 0899052 SP Compt w/Strap, Backboard, Vertical
in Hose Bed, Mounted to Side Sheet

BACKBOARD STORAGE
A compartment for one (1) backboard will be provided in the hose bed. The compartment will be mounted to the right side sheet. The compartment will be made of the same material as the body and finished to match the hosebed side sheets.

The compartment will be sized for a backboard 72.00" long x 16.00" wide x 2.00" high. A Velcro® strap will be provided at the rear of the compartment to restrain the backboard. 0567897 Pike Pole, 8' Fire Hooks Unlimited,
New York Roof Hook, Steel, Pry End,
RH-8
8' PIKE POLE
There will be two (2) Fire Hooks Unlimited, New York Hook , 8' long roof hook with steel shaft and chisel (pry) end provided LS long handle tool compartment. 0724980 Tube, Pike Pole 8' or Longer, Thru
Body Long Tool Storage

PIKE POLE STORAGE
There will be storage designated left side for Two (2) pike poles 8' or longer pike poles stored in a tube with a 1.38" notch, to accommodate a New York style pike pole for the head of a pike pole.

This will be located thru- body in the long tool storage compartment. 0549137 Not Required, Pike Pole, 6'

0733065 Not Required

0672603 SP Compt, Below Tank Tee, Long
Handled Tools

COMPARTMENT FOR LONG HANDLED TOOLS
There will be one (1)compartment(s) provided on the left side ABOVE both rear 2.50" discharges side at the rear of the truck below the water tank tee. The compartment will be sized to hold long handled tools. The compartment will be (1) 10' folding ladder and (2) 8' NY Hooks .

At the rear of the compartment will be a smooth aluminum door with a D-handle latch.

Bid #: 716 37
EXHIBIT 1 693
0751594 SP Steps, Folding, Front of Body, Cargo
Bed Access, Cast Products SP6610
w/LED,Logo

FOLDING STEPS FRONT OF BODY
Cast Products, model SP6610, folding steps will be provided full height on the left side and right side body compartments to provide access to the cargo bed. Steps will be spaced evenly on the sales drawing. Actual quantity may vary due to pump panel interferences but will meet the NFPA required maximum stepping height.

The steps will incorporate an LED light to illuminate the stepping surface.

The steps can be used as a hand hold with an opening wide enough for a gloved hand.

The Pierce logo will be provided in the underside of the step. 0792626 SP Steps, Folding, Cast Products, Model
SP6610, LED Lighted, Rear Body,
Pierce Logo

REAR ACCESS STEP
Cast Product, model SP6610, lighted folding steps will be provided at the rear. The step platform will be 6.70" wide by 8.70" deep with a handhold provided at the front of the step. LED lights will be provided above and below the step surface. The Pierce logo will be provided in the underside of the step.
0015500 Pump House, Side Control, 54"

PUMP COMPARTMENT
The pump compartment will be separate from the hose body and compartments so that each may flex independently of the other. It will be a fabricated assembly of steel tubing, angles and channels which supports both the fire pump and the side running boards.

The pump compartment will be mounted on the chassis frame rails with rubber biscuits in a four point pattern to allow for chassis frame twist.

The pump compartment, pump, plumbing and gauge panels will be removable from the chassis in a single assembly.

PUMP MOUNTING
The pump will be mounted to a substructure which will be mounted to the chassis frame rail using rubber isolators. The mounting will allow the chassis frame rails to flex independently without damage to the fire pump.

PUMP CONTROL PANELS (Side Control)
All pump controls and gauges will be located at the left side of the apparatus and properly marked.

The control panels will be 54.00" wide.

Polished stainless steel trim collars will be installed around all inlets and outlets.

All push/pull valve controls will have 1/4 turn locking control rods with polished chrome plated zinc tee handles. Guides for the push/pull control rods will be chrome plated zinc castings securely mounted to the pump panel. Push/pull valve controls will be capable of locking in any position.

The control rods will pull straight out of the panel and will be equipped with universal joints to eliminate binding.

The identification tag for each valve control will be recessed in the face of the tee handle.

All discharge outlets will have color coded identification tags, with each discharge having its own unique color. Color coding will include the labeling of the outlet and the drain for each corresponding discharge.

All line pressure gauges will be mounted in individual chrome plated castings with the identification tag recessed in the casting below the gauge. All remaining identification tags will be mounted on the pump panel in chrome plated bezels. Mounting of the castings and identification bezels will be done with a threaded peg cast on the back side of the bezel or screws. screws.
0037731 Pump House Structure, Raised,
Included with Ladder Storage

0762418 SP Lighting, Amdor AY-LB-12HW020,
20", Cargo Area Only, PP Lts Swt

CARGO AREA LIGHTING
There will be two (2) Amdor®, Model AY-LB-12HW020, 350 lumen, 20" long, white LED light stick (s) provided below the body flange of the cargo area. These lights will be activated by the panel light switch located on the pump panel. in the cargo area to illuminate the hose reels during reloading
0618741 Blister, Side Sheet Above Pump
House, Location

CARGO SIDE SHEET BLISTER
There will be a total of two (2) cargo side sheet(s) blistered out. The location will be on the left and right side. The blister(s) will allow additional room in the cargo compartment for installation of booster reels.
0797005 Pump, Waterous, CXC20, 1500
GPM, Single Stage, Midship Split
Shaft
PUMP
Fire pump will be a Waterous CXC20, 1500 gpm, single (1) stage centrifugal type. The pump will be an end suction, pedestal mount, single inlet type.

Pump will be the class "A" type.

Pump will deliver the percentage of rated discharge at pressures indicated below:
100 percent of rated capacity at 150 psi net pump pressure. 70 percent of rated capacity at 200 psi net pump pressure. 50 percent of rated capacity at 250 psi net pump pressure.

Pump body will be close-grained gray iron, bronze fitted.

Impeller shaft will be stainless steel, accurately ground to size. It will be supported by oil or grease lubricated, anti-friction ball bearings for rigid precise support.

Bearings will be protected from water and sediment by suitable stuffing boxes, slinger rings, and oil seals. No special or sleeve type bearings will be used.

Bid #: 716 38
EXHIBIT 1 694
0004482 Seal, Mechanical, Waterous

Pump will be equipped with a self-adjusting, maintenance-free, mechanical shaft seal.

The mechanical seal will consist of a flat, highly polished, spring fed carbon ring that rotates with the impeller shaft. The carbon ring will press against a highly polished stainless steel stationary ring that is sealed within the pump body.

In addition, a throttling ring will be pressed into the steel chamber cover, providing a very small clearance around the rotating shaft in the event of a mechanical seal failure. The pump performance will not deteriorate, nor will the pump lose prime, while drafting if the seal fails during pump operation.

Wear rings will be bronze and easily replaceable to restore original pump efficiency and eliminate the need to replace the entire pump casing due to wear. 0559769 Trans, Pump, Waterous C20 Series

PUMP TRANSMISSION
The pump transmission will be made of a three (3) piece, aluminum, horizontally split casing.

Power transfer to pump will be through a high strength Morse HY-VO silent drive chain. By the use of a chain rather than gears, 50% of the sprocket will be accepting or transmitting torque, compared to two (2) or three (3) teeth doing all the work.

Drive shafts will be 2.35" diameter hardened and ground alloy steel and supported by ball bearings. The case will be designed to eliminate the need for water cooling. 0635600 Pumping Mode, Stationary Only

PUMPING MODE
An interlock system will be provided to ensure that the pump drive system components are properly engaged so that the apparatus can be safely operated. The interlock system will be designed to allow stationary pumping only.
0605125 Pump Shift, Air w/o Manual Override,
Split Shaft, Interlocked, Waterous

AIR PUMP SHIFT
Pump shift engagement will be made by a two (2) position sliding collar, actuated pneumatically (by air pressure), with a three (3) position air control switch located in the cab.

Two (2) indicator lights will be provided adjacent to the pump shift inside the cab. One (1) green light will indicate the pump shift has been completed and be labeled "pump engaged". The second green light will indicate when the pump has been engaged, and that the chassis transmission is in pump gear. This indicator light will be labeled "OK to pump".

The pump shift will be interlocked to prevent the pump from being shifted out of gear when the chassis transmission is in gear to meet NFPA requirements.

The pump shift control in the cab will be illuminated to meet NFPA requirements. 0003148 Transmission Lock-up, EVS TRANSMISSION LOCK-UP
The direct gear transmission lock-up for the fire pump operation will engage automatically when the pump shift control in the cab is activated.
0004547 Auxiliary Cooling System

AUXILIARY COOLING SYSTEM
A supplementary heat exchange cooling system will be provided to allow the use of water from the discharge side of the pump for cooling the engine water. The heat exchanger will be a separate unit. It will be installed in the pump or engine compartment with the control located on the pump operator's control panel. The exchanger will be plumbed to the master drain valve. 0014486 Not Required, Transfer Valve, Single
Stage Pump
0746508 Valve(s), Relief Intake, Trident Air
Max, Control Location

INTAKE RELIEF VALVE
One (1) Trident Air Max intake relief valve(s) will be installed on the suction side of the pump preset at 125 psig.

The relief valve will have a working range of 50 PSI to 350 PSI.

The outlet will terminate below the frame rails with a 2.50" National Standard hose thread adapter and will have a "do not cap" warning tag.

One (1) adjustable air regulator and pressure indicating gauge will be located on a common bezel behind the right side pump panel with a stainless steel access door to control the intake valve(s). 0004525 Valve, Pump Relief w/ Indicator
Lights, Waterous

RELIEF VALVE
A Waterous adjustable relief valve, specially designed for fire service, will be provided.

Valve will be positive, quick acting, and include an instantaneous on/off control. When in the off position, the relief valve will functionally be removed from the system. When turned back to the on position, the relief valve will again monitor and maintain the previous pressure setting.

Control for adjusting pressure will be elliptical shaped for positive grip.

An easily removable pilot valve strainer will be provided and be accessible from the pump operator's panel.

Two (2) indicator lights will be furnished, showing the position of the relief valve (amber for open and green for closed).
0072153 Primer, Trident, Air Prime, Air
Operated

PRIMING PUMP
The priming pump will be a Trident Emergency Products compressed air powered, high efficiency, multistage venturi based AirPrime System, conforming to standards outlined in the current edition of NFPA 1901.

All wetted metallic parts of the priming system are to be of brass and stainless steel construction.

One (1) priming control will open the priming valve and start the pump primer.

Bid #: 716 39
EXHIBIT 1 695
0048201 Drain, Class 1 Multi-Port, IPO Std
Pump Drain

PUMP DRAIN
A Class 1 multi port pump drain will be used in place of the standard pump drain. 0504715 Line, 0.375" Recirculating, Water
Tank

RECIRCULATING LINE
A 3/8" line will be run from the discharge side of the main pump to the water tank to help keep the pump cool when water is not being discharged. This line will be designed to circulate water from the pump back to the tank when the recirculating valve is open. This water circulation will help to maintain the pump water temperature at a safe level. The recirculation valve will be located on the left pump operator's panel.
0658368 Thermal Relief Valve, OPM, w/Red
Warning Light, Waterous Pump

THERMAL RELIEF VALVE
A Waterous Overheat Protection Manager (OPM) will be included on the pump that monitors pump water temperature and opens to relieve water to cool the pump when the temperature of the pump water exceeds 140 Degrees F (60 C) and a red warning light that is triggered when the water in the pump reaches 180 F (82 C).

The warning light will act as an additional protection device if the temperature in the pump keeps rising after the valve opens. The warning light with a test switch will be mounted on the pump operator panel.

The discharge line will be plumbed to ground.
0780364 Manuals, Pump, (2) Total, Electronic
Copies

PUMP MANUALS
There will be a total of two (2) pump manuals provided by the pump manufacturer and furnished with the apparatus. The manuals will be provided by the pump manufacturer in the form of two (2) electronic copies. Each manual will cover pump operation, maintenance, and parts. 0603129 Plumbing, Stainless Steel and Hose,
Single Stage Pump

PLUMBING, STAINLESS STEEL AND HOSE
All inlet and outlet lines will be plumbed with either stainless steel pipe, flexible polypropylene tubing or synthetic rubber hose reinforced with hi-tensile polyester braid. All hose's will be equipped with brass or stainless steel couplings. All stainless steel hard plumbing will be a minimum of a schedule 10 wall thickness.

Where vibration or chassis flexing may damage or loosen piping or where a coupling is required for servicing, the piping will be equipped with victaulic or rubber couplings.

Plumbing manifold bodies will be ductile cast iron or stainless steel.

All piping lines are to be drained through a master drain valve or will be equipped with individual drain valves. All drain lines will be extended with a hose to drain below the chassis frame.

All water carrying gauge lines will be of flexible polypropylene tubing.

All piping, hose and fittings will have a minimum of a 500 PSI hydrodynamic pressure rating. 0795135 Plumbing, Stainless Steel, w/Foam
System

FOAM SYSTEM PLUMBING
All piping that is in contact with the foam concentrate or foam/water solution will be stainless steel. The fittings will be stainless steel or brass. Cast iron pump manifolds will be allowed. 0004645 Inlets, 6.00" - 1250 GPM or Larger
Pump

MAIN PUMP INLETS
A 6.00" pump manifold inlet will be provided on each side of the vehicle. The suction inlets will include removable die cast zinc screens that are designed to provide cathodic protection for the pump, thus reducing corrosion in the pump.
0014650 Pump Suction Tube(s), Short, All

SHORT SUCTION TUBE(S)
The suction tube(s) on the water pump will have short suction tube(s) installed to allow for installation of adapters, elbows or intake valves without excessive overhang. 0699096 Not Required, Cap, Main Pump Inlet,
Included w/Storz Adapter
0084610 Valves, Akron 8000 series- All

VALVES
All ball valves will be Akron® Brass. The Akron valves will be the 8000 series heavy-duty style with a stainless steel ball and a simple two-seat design. No lubrication or regular maintenance is required on the valve.

Valves will have a ten (10) year warranty.
0004686 Valve, Inlet(s) Recess Behind Panel,
Side Cntrl
The location of the valve for the two (2) inlets will be behind the pump panel. 0004700 Control, Inlet, at Valve

INLET CONTROL
The side auxiliary inlet(s) will incorporate a quarter-turn ball valve with the control located at the inlet valve. The valve operating mechanism will indicate the position of the valve.

Bid #: 716 40
EXHIBIT 1 696
0004660 Inlet (1), Left Side, 2.50"

LEFT SIDE INLET
There will be one (1) auxiliary inlet with a 2.50" valve at the left side pump panel, terminating with a 2.50" (F) National Standard hose thread adapter.

The auxiliary inlet will be provided with a strainer, chrome swivel and plug. 0723551 Inlet (1), Right Side, 2.50"

RIGHT SIDE INLET
There will be one (1) auxiliary inlet with a 2.50" valve at the right side pump panel, terminating with a 2.50" (F) National Standard hose thread adapter.

The auxiliary inlet will be provided with a strainer, chrome swivel and plug. 0034720 Anode, Zinc, Pair, Pump Inlets

ANODE, INLET
A pair of sacrificial zinc anodes will be provided in the water pump inlets to protect the pump from corrosion.
0092569 No Rear Inlet (Large Dia) Requested

0064116 No Rear Inlet Actuation Required

0092696 Not Required, Cap, Rear Inlet

0009648 No Rear Intake Relief Valve Required
on Rear Inlet
0092568 No Rear Auxiliary Inlet Requested

0723049 Valve, .75" Bleeder, Aux. Side Inlet,
"T" Swing Handle

INLET BLEEDER VALVE
A 0.75" bleeder valve will be provided for each side gated inlet.

The valves will be located behind the panel with a "T" swing style handle control extended to the outside of the panel.

The handles will be chrome plated and provide a visual indication of valve position. The swing handle will provide an ergonomic position for operating the valve without twisting the wrist and provides excellent leverage.

The water discharged by the bleeders will be routed below the chassis frame rails. 0029043 Tank to Pump, (1) 3.00" Valve, 3.00"
Plumbing

TANK TO PUMP
The booster tank will be connected to the intake side of the pump with stainless steel piping and a quarter turn 3.00" full flow line valve with the control remotely located at the operator's panel.

Tank to pump line will run straight (no elbows) from the pump into the front face of the water tank and angle down into the tank sump. A rubber coupling will be included in this line to prevent damage from vibration or chassis flexing.

A check valve will be provided in the tank to pump supply line to prevent the possibility of "back filling" the water tank.
0004905 Outlet, Tank Fill, 1.50"

TANK REFILL
A 1.50" combination tank refill and pump re-circulation line will be provided, using a quarter-turn full flow ball valve controlled from the pump operator's panel. 0062133 Control, Outlets, Manual, Pierce HW
if applicable

DISCHARGE OUTLET CONTROLS
The discharge outlets will incorporate a quarter-turn ball valve with the control located at the pump operator's panel. The valve operating mechanism will indicate the position of the valve.

If a handwheel control valve is used, the control will be a minimum of a 3.9" diameter stainless steel handwheel with a dial position indicator built in to the center of the handwheel.

Any 3.00 inch or larger discharge valve will be a slow-operating valve in accordance with NFPA

16.7.5.3. 0004940 Outlet, Left Side, 2.50"

LEFT SIDE DISCHARGE OUTLETS
There will be Two (2) discharge outlets with a 2.50" valve on the left side of the apparatus, terminating with a 2.50" (M) National Standard hose thread adapter. 0005091 Elbow, Left Side Outlets, 45 Degree,

2.50" FNST x 2.50" MNST, VLH

LEFT SIDE OUTLET ELBOWS
The 2.50" discharge outlets located on the left side pump panel will be furnished with a 2.50" (F) National Standard hose thread x 2.50" (M) National Standard hose thread, chrome plated, 45 degree elbow.

The elbow will be Pierce VLH, which incorporates an exclusive thread design to automatically relieve stored pressure in the line when disconnected.

Bid #: 716 41
EXHIBIT 1 697
0092570 Not Required, Outlets, Left Side
Additional
0035094 Not Required, Elbow, Left Side
Outlets, Additional
0004945 Outlet, Right Side, 2.50"

RIGHT SIDE DISCHARGE OUTLETS
There will be One (1) discharge outlet with a 2.50" valve on the right side of the apparatus, terminating with a 2.50" (M) National Standard hose thread adapter. 0025091 Elbow, Right Side Outlets, 45
Degree, 2.50" FNST x 2.50" MNST,
VLH

RIGHT SIDE OUTLET ELBOWS
The 2.50" discharge outlets located on the right side pump panel will be furnished with a 2.50" (F) National Standard hose thread x 2.50" (M) National Standard hose thread, chrome plated, 45 degree elbow.

The elbow will be Pierce VLH, which incorporates an exclusive thread design to automatically relieve stored pressure in the line when disconnected.
0092571 Not Required, Outlets, Right Side
Additional
0089584 Not Required, Elbow, Right Side
Outlets, Additional
0005047 Outlet, 4" w/4" Right, Handwheel

LARGE DIAMETER DISCHARGE OUTLET
There will be a 4.00" discharge outlet with a 4.00" Akron valve installed on the right side of the apparatus, terminating with a 4.00" (M) National Standard hose thread adapter. This discharge outlet will be actuated with a handwheel control at the pump operator's control panel.

An indicator will be provided to show when the valve is in the closed position. 0005097 Elbow, Large Dia Outlet, 30 Deg,

4.00" FNST x 5.00" Storz

LARGE DIAMETER OUTLET ELBOWS
The 4.00" outlet(s) will be furnished with one (1) 4.00" (F) National Standard hose thread x 5.00" Storz elbow adapter with Storz cap.
0649939 Outlet, Front, 1.50" w/2" Plumbing

FRONT DISCHARGE OUTLET
There will be one (1) 1.50" discharge outlet piped to the front of the apparatus and located on the top of the left side of the front bumper.

Plumbing will consist of 2.00" piping and flexible hose with a 2.00" ball valve with control at the pump operator's panel. A fabricated weldment made of stainless steel pipe will be used in the plumbing where appropriate. The piping will terminate with a 1.50" NST with 90 degree stainless steel swivel.

There will be automatic drains provided at all low points of the piping. 0004995 Outlet, Rear, 2.50"

REAR DISCHARGE OUTLET
There will be Two (2) discharge outlets piped to the rear of the hose bed, left side, installed so proper clearance is provided for spanner wrenches or adapters. Plumbing will consist of 2.50" piping along with a 2.50" full flow ball valve with the control from the pump operator's panel. 0045091 Elbow, Rear Outlets, 45 Degree,

2.50" FNST x 2.50" MNST, VLH

REAR OUTLET ELBOWS
The 2.50" discharge outlets located at the rear of the apparatus will be furnished with a 2.50" (F) National Standard hose thread x 2.50" (M) National Standard hose thread, chrome plated, 45 degree elbow.

The elbow will be Pierce VLH, which incorporates an exclusive thread design to automatically relieve stored pressure in the line when disconnected.
0092574 Not Required, Outlet, Rear, Additional

0085695 Not Required, Elbow, Rear Outlets,
Large, Additional
0092573 Not Required, Outlet, Hose
Bed/Running Board Tray

0752097 Caps/Plugs for 1.00" to 3.00"
Discharges/Inlets, Chain

DISCHARGE CAPS/ INLET PLUGS
Chrome plated, rocker lug, caps with chain will be furnished for all discharge outlets 1.00" thru

3.00" in size, besides the pre-connected hose outlets.

Chrome plated, rocker lug, plugs with chain will be furnished for all auxiliary inlets 1.00" thru 3.00" in size.

The caps and plugs will incorporate a thread design to automatically relieve stored pressure in the line when disconnected.

Bid #: 716 42
EXHIBIT 1 698
0723042 Valve, 0.75" Bleeder, Discharges, "T"
Swing Handle

OUTLET BLEEDER VALVE
A 0.75" bleeder valve will be provided for each outlet 1.50" or larger. Automatic drain valves are acceptable with some outlets if deemed appropriate with the application.

The valves will be located behind the panel with a T swing style handle control extended to the outside of the side pump panel.

The handles will be chrome plated and provide a visual indication of valve position.

The T swing handle will provide an ergonomic position for operating the valve without twisting the wrist and provides excellent leverage.

Bleeders will be located at the bottom of the pump panel. They will be properly labeled identifying the discharge they are plumbed in to.

The water discharged by the bleeders will be routed below the chassis frame rails. 0005080 Reducer, 2.50" FNST x 1.50" MNST,
w/Cap

REDUCER
There will be three (3) adapters with 2.50" FNST x 1.50" MNST threads and a 1.50" chrome plated cap installed on both left side and one right side 2.5" discharges. 0091106 Outlet, 3.00" Deluge w/TFT Extend-aGun XG18, Handwheel DELUGE RISER A 3.00" deluge riser will be installed above the pump in such a manner that a monitor can be mounted and used effectively. Piping will be rigidly braced and installed securely so no movement develops when the line is charged. The riser will be gated and controlled at the pump operator's panel with a handwheel control.

TELESCOPIC PIPING
The deluge riser piping will include a 18.00" Task Force Model XG18 Extend-A-Gun extension.

This extension will be telescopic to allow the deluge gun to be raised 18.00" increasing the range of operation.

A position sensor will be provided on the telescopic piping that will activate the "do not move vehicle" light inside the cab when the monitor is in the raised position. 0095958 Deluge Outlet, Special
Height/Location

DELUGE OUTLET SPECIAL INSTRUCTIONS
The deluge gun outlet will be located no taller than the hose reels when in the retracted position. 0770359 No Monitor Requested,
Customer/Dealer Furnished and
Installed

MONITOR
A customer/dealer supplied and installed make and model TFT XFC-52 monitor will be properly installed on the deluge riser.
0029304 No Nozzle Req'd

0046857 Deluge Mount, For TFT Crossfire
Monitor, TFT Manual Extend-A-Gun
Only
The deluge riser Extend-a-Gun will have provisions for direct mounting a Task Force Tips CrossFire monitor.
0723726 Speedlay Module Not Required

0722432 Hose Restraint Not Required, No
Speedlay Module
0723395 Speedlays, Not Required

0723394 Speedlays, Not Required

0029210 Crosslays Sngl Sheet, (2+) 1.50",
Spl. Cap/Arrangement
CROSSLAY HOSE BEDS, 1.50"
Two (2) crosslays with 1.50" outlets will be provided. Each bed to be capable of carrying 200' x

1.75" D.J. hose. CLEAR INSIDE DIMENSION OF EACH CROSSLAY TO BE 10.50" WIDE X

18.00" HIGH - NO EXCEPTIONS and will be plumbed with 2.00" i.d. pipe and gated with a 2.00" quarter turn ball valve.

Outlets to be equipped with a 1.50" National Standard hose thread 90 degree swivel located in the hose bed so that hose may be removed from either side of apparatus.

The crosslay controls will be at the pump operator's panel.

The center crosslay dividers will be fabricated of .25" aluminum and will provide adjustment from side to side. The divider will be unpainted with a brushed finish.

Vertical scuffplates, constructed of stainless steel, will be provided at the front and rear ends of the bed on each side of vehicle.

Crosslay bed flooring will consist of removable perforated brushed aluminum. 0029196 Not Required, 2.50" Crosslay

Bid #: 716 43
EXHIBIT 1 699
0590942 Hose Restraint, Crosslay/Deadlay, 1"
Heavy Nylon Web, Strap Fasteners,
Each Side

CROSSLAY/DEADLAY HOSE RESTRAINT
A black 1.00" nylon webbing design with 2.00" box pattern will be provided across each end of two (2) crosslay/deadlay(s) to secure the hose during travel. The webbing will be permanently attached at the top of the crosslay/deadlay opening(s). 1.00" web straps will loop through footman loops located at the opposite end of the permanently attached webbing. The straps will attach with a pair of velcro straps fasteners.
0029260 Not Required, Speedlays

0750536 Hose Restr, Spdly, Not Required, No
Spdly
0590877 Hose Restraint, Crosslay/Deadlay,
Aluminum Treadplate, Top Only

CROSSLAY/DEADLAY HOSE RESTRAINT
An aluminum treadplate cover, hinged at the front will be installed over the top of the crosslay/deadlay(s). It will include a latch at each end of the cover to hold it securely in place, a chrome grab handle at each end for opening and closing the cover and a foam rubber gasket where the cover comes into contact to a painted surface. The cover will be provided with no stay arm device hold open device.
0895329 SP Crosslays, 17.00" Lower Than
Standard - w/Raised PH

CROSSLAY 17.00" LOWER THAN STANDARD
The crosslays will be lowered 17.00" from standard with a raised pumphouse. 0790990 SP Reel, Booster, Two (2) - Over Pump,
Steel, No Rollers

BOOSTER HOSE REELS
Two (2) Hannay electric rewind booster hose reels will be installed over the pump in a recessed open compartment, one (1) each side.

The exterior finish of the reel will be painted job color matching the lower body.

The discharge controls will be provided at the pump operator's panel. Plumbing to the reels will consist of 1.50" Aeroquip hose and a 1.50" valves.
0581287 Switches, Reel Rewind - Two
Reels/Two Switches, 70 Amp

Reel motors will be protected from overload with 70 amp automatic reset circuit breakers.

Electric rewind control will be two (2) chrome buttons, one (1) mounted on each pump panel adjacent to hose reel.
0606182 SP Hose, Booster - (2) Reels W/200' of

1.00"/800 PSI (100 + 100)
Booster hose, 1.00" diameter and 200 feet long, with chrome plated Barway, or equal couplings will be provided on each reel. The 200 feet of hose will be provided in two (2) 100 feet lengths.

Working pressure of the booster hose will be a minimum of 800 psi. 0005244 Capacity, Hose Reel 200' of 1" Capacity of the hose reel will be 200 feet of 1.00" booster hose. 0007428 Nozzle for Booster Reel Not Req'd

0515688 Gauge, Hose Reel, (Match Panel
Gauges)

PRESSURE GAUGE
There will be a pressure gauge provided for two (2) hose reel(s). The gauge will be located per the pump panel drawings. The gauge will match the discharge outlet gauges. 0025028 Cutout for Reel Access, W/ Roller
Assembly

HOSEREEL ACCESS
A quantity of two (2) cutout(s) will be provided in the one (1) each side for the hose reel(s). These cutout(s) will allow access to the hose and provide a window to view the reel. Stainless steel rollers with nylon bushings will be mounted horizontally and vertically around the cutout. 0085328 Nozzle Cup, Zico w/Bracket NOZZLE CUP AND BRACKET A Zico nozzle cup and chrome plated mounting bracket will be provided for storage of the booster reel nozzle.

There will be two (2) provided. The nozzle cup(s) will have a 3-1/2" inside diameter and will be located KEEP LOOSE, location TBD at final inspection.
0095358 Foam Sys, Husky 12, Single Agent

FOAM PROPORTIONER
A Pierce Husky™ 12 foam proportioning system will be provided that is an on demand, automatic proportioning, single point, direct injection system suitable for all types of Class A and B foam concentrates, including the high viscosity (6000 cps), alcohol resistant Class B foams. Operation will be based on direct measurement of water flow, and remain consistent within the specified flows and pressures. The system will automatically balance and proportion foam solution at rates from .1 percent to 9.9 percent regardless of variations in water pressure and flow, up to the maximum rated capacity of the foam concentrate pump.

The design of the system will allow operation from draft, hydrant, or relay operation. This will provide a versatile system to meet the demands at a fire scene.

System Capacity
The system will have the ability to deliver the following minimum foam solution flow rates that Bid #: 716 44
EXHIBIT 1 700
meet or exceed NFPA requirements at a pump rating of 250 psi. 200 gpm @ 6 percent
400 gpm @ 3 percent
1200 gpm @ 1 percent
The foam concentrate setting may be adjusted in .1 percent increments from .1 percent to 9.9 percent. Typical settings are .3 percent, .5 percent and 1.0 percent (The maximum capacity will be limited to the plumbing and water pump capacity).

Control System
The system will be equipped with a digital electronic control display located on the pump operators panel. Push button controls will be integrated into the panel to turn the system on/off, control the foam percentage, direct which foam to use on a multi-tank system, and to set the operation modes (automatic, manual, draft, calibration, or flush).

The percent of injection will have presets for Class A or Class B foam. These presets can be changed at the fire department as desired. The percent of injection will be able to be easily changed at the scene to adjust to changing demands.

In order to minimize the use of abbreviations and interpretations, system information will be displayed on the panel by way of .50 tall LEDs that total 14 characters (two (2) lines of seven (7) each). System on and foam pump on indicator lights will also be included. Information displayed will include mode of operation (automatic, manual, draft, calibration, or flush), foam supply selected (Class A or Class B), water total, foam total, foam percentage, remaining gallons, and time remaining.

The control display will direct a microprocessor, which receives input from the systems water flow meter while also monitoring the position of the foam concentrate pump. The microprocessor will compare the values of the water flow versus the position/rate of the foam pump, to ensure the proportion rate is accurate. One (1) check valve will be installed in the plumbing to prevent foam from contaminating the water pump.

Low Level Foam Tank
The control head will display a warning message when the foam tank in use is below a quarter tank.

Hydraulic Drive System
The foam concentrate pump will be powered by a hydraulic drive system, which is automatically activated, whenever the vehicle water pump is engaged. A large parasitic electric load used to power the foam pump can cause an overload of the chassis electrical system.

Hydraulic oil cooler will be provided to automatically prevent overheating of the hydraulic oil, which is detrimental to system components. The oil/water cooler will be designed to allow continuous system operation without allowing hydraulic oil temperature to exceed the oil specifications.

The hydraulic oil reservoir will be of four (4) gallons minimum capacity and will also be of sufficient size to minimize foaming and be located to facilitate checking oil level or adding oil without spillage or the need to remove access panels.

Foam Concentrate Pump
The foam concentrate pump will be of positive displacement, self-priming; linear actuated design, driven by the hydraulic motor. The pump will be constructed of brass body; chrome plated stainless steel shaft, with a stainless steel piston. In order to increase longevity of the pump, no aluminum will be present in its construction.

A relief system will be provided which is designed to protect the drive system components and prevent over pressuring the foam concentrate pump
The foam concentrate pump will have minimum capacity for 12 gpm with all types of foam concentrates with a viscosity at or below 6000 cps including protein, fluoroprotein, AFFF, FFFP, or AR-AFFF. The system will deliver only the amount of foam concentrate flow required, without recirculating foam back to the storage tank. Recirculating foam concentrate back to the storage tank can cause agitation and premature foaming of the concentrate, which can result in system failure. The foam concentrate pump will be self-priming and have the ability to draw foam concentrate from external supplies such as drums or pails.

External Foam Concentrate Connection
An external foam pick-up will be provided to enable use of a foam agent that is not stored on the vehicle. The external foam pick-up will be designed to allow continued operation after the onboard foam tank is empty. The external foam pick-up will be designed to allow use with training foam or colored water for training purposes.

Panel Mounted Strainer / External Pick-Up Connection
A bronze body strainer / connector unit will be provided. The unit will be mounted to the pump panel. The external foam pick-up will be one (1) 1.00" male connection with chrome-plated cap integrated to a 2.00" strainer cleanout cap. A check valve will be installed in the pick-up portion of the cleanout cap. A basket style stainless steel screen will be installed in the body of the strainer / connector unit. Removal of the 2.00" cleanout cap will be all that is required to gain access to and remove the stainless steel basket screen. The strainer / connector unit will be ahead of the foam concentrate pump inlet port to insure that all agents reaching the foam pump has been strained.

Pick-Up Hose
A 1.00" flexible hose with an end for insertion into foam containers will be provided. The hose will be supplied with a 1.00" female swivel NST thread swivel connector. The hose will be shipped loose.

Discharges
The foam system will be plumbed to six (6) discharges. The discharges capable of dispensing foam will be #1 crosslay, #2 crosslay, #5 rear discharge, #7 rear discharge and both booster reels.

System Electrical Load
The foam proportioning will not impose an electrical load on the vehicle electrical system any greater than five (5) amps at 12VDC.

Foam Supply Valve
An electric valve will be used for the foam supply valve. The foam supply valve will be controlled at the foam system control head for ease of operation. The supply valve will be electric, remote controlled, to eliminate air pockets in the foam tank supply hose.

Maintenance Message
A message will be displayed on the control head to advise when system maintenance needs to be performed. The message will display interval for cleaning the foam strainer, cleaning for the water strainers, and changing the hydraulic oil.

Flush System
Bid #: 716 45
EXHIBIT 1 701
The system will be designed such that a flush mode will be provided to allow the system to flush all foam concentrate with clear water. The flush circuit control logic will ensure the foam tank supply valve is closed prior to opening the flush valve. The flush valve will be operated at the foam system control head for ease of operation. The valve will be electrically controlled and located as close to the foam tank supply valve as possible. A manual flush drain valve will be labeled and located under the left side running board.
0012126 Not Required, CAF Compressor

0561708 Not Required, Refill, Foam Tank
0031896 Demonstration, Foam System, Dealer
Provided
0022539 Foam Cell, 20 Gallon, Reduce Water

FOAM TANK
The foam tank will be an integral portion of the polypropylene water tank. The cell will have a capacity of 20 gallons of foam with the intended use of Class A foam. The foam cell will reduce the capacity of the water tank. The foam cell will have a screen in the fill dome and a breather in the lid.
0505016 Drain, 1.00", Foam Tank #1, Husky
12 Foam System

FOAM TANK DRAIN
A system of 1.00" foam tank drains will be provided, integrated into the foam systems strainer and tank to foam pump valve management system. The tank to pump hoses running from the tank(s) to the panel mounted strainer will 1.00" diameter. The foam system controller will have a mode that allows for a given foam valve to be opened at will. Flow of foam from the tank valve to the strainer will be usable as a tank drain mode.

An adaptor will be supplied, that allows the 1.00" foam intake screen to assembly to be used as a drain outlet. The standard supplied 1.00" foam pick up hose will be attached to the screen assembly by way of the adapter. The drain mode will allow the operator to open and close the tank valve as required from the control head, to drain foam and re-fill foam containers through the connected hose, without foam spillage beneath the vehicle. 0091079 Not Required, Foam Tank #2

0091112 Not Required, Foam Tank #2 Drain

Bid #: 716 46
EXHIBIT 1 702
0738111 Approval Dwg, All Pump Panel(s),
Includes Color And Label Tags,
FLEET
The following drawing(s) will be provided for approval by the customer. The drawing(s) will be made to match No Similar Pierce Truck similar Pierce job number.

PUMP OPERATOR'S PANEL DRAWING
A detailed drawing to scale of the pump operator's panel will be provided for the customer to review. The drawing will include all of the gauges, controls, switching, etc.., located on the pump operator's panel. The customer will be allowed to make changes and/or mark-ups to this approval drawing. The fire apparatus manufacturer will make revisions (If needed) to the drawing per the customer changes and/or mark-ups as long as the changes are physically possible within a specific product line.

The finalized and signed customer approved pump operator's panel drawing will become part of the contract documents.

Due to the way drain(s), bleeder(s), operational/maintenance tag(s) and NFPA required warning tag(s) are placed on pump panel(s), these items will NOT be shown on any pump panel approval drawing(s). These item(s) will be placed on pump panel(s) at the fire apparatus manufacturer discretion.

REMAINING PUMP PANEL(S)
Detailed drawing(s) to scale of the remaining pump panel(s) will be provided for the customer to review. The drawing(s) will include all of the gauges, controls, switching, etc.., located on the pump panel(s). The customer will be allowed to make changes and/or mark-ups to these approval drawing(s). The fire apparatus manufacturer will make revisions (If needed) to the drawing(s) per the customer changes and/or mark-ups as long as the changes are physically possible within a specific product line.

The finalized and signed customer approved pump panel drawing(s) will become part of the contract documents.

Due to the way drain(s), bleeder(s), operational/maintenance tag(s) and NFPA required warning tag(s) are placed on pump panel(s), these items will NOT be shown on any pump panel approval drawing(s). These item(s) will be placed on pump panel(s) at the fire apparatus manufacturer discretion.

COLOR CODED TAGS
A detailed drawing/chart of the colors used on all of the inlet(s) and outlet(s) will be provided for the customer to review. The customer will be allowed to make changes and/or mark-ups to this approval drawing/chart. The fire apparatus manufacturer will make revisions (If needed) to the drawing per the customer changes and/or mark-ups as long as the changes are physically possible within a specific product line.

The finalized and signed customer approved drawing/chart of the colors will become part of the contract documents.

SPECIAL TEXT/VERBIAGE TAGS
A detailed drawing/chart of the text/verbiage used on all of the inlet(s) and outlet(s) will be provided for the customer to review. The customer will be allowed to make changes and/or markups to this approval drawing/chart. The fire apparatus manufacturer will make revisions (If needed) to the drawing per the customer changes and/or mark-ups as long as the changes are physically possible within a specific product line.

The finalized and signed customer approved drawing/chart of the text/verbiage will become part of the contract documents.
0035570 Pump Panel Configuration, No Match
Required

PUMP PANEL CONFIGURATION
The pump panel configuration will be neat and orderly.
0005525 Material, Pump Panels, Side Control
Brushed Stainless

PUMP AND GAUGE PANEL
The pump and gauge panels will be constructed of stainless steel with a brushed finish. A polished aluminum trim molding will be provided on both sides of the pump panel. 0721776 Panel, Pump Access - Right Side,
Hinged, Side Control

PUMP ACCESS
Right Side Panel
The right side pump panel will be hinged along the rearward edge.

Panel Fastener
The right side hinged panel will be secured using a chrome flush lift and turn latch .

The right side lower (drain bank) and all left side panel will be secured using screws. 0583824 Light, Pump Compt, Wln 3SC0CDCR
LED White

PUMP COMPARTMENT LIGHT
There will be one (1) Whelen®, Model 3SC0CDCR, 3.00" white 12 volt DC LED light(s) with Whelen, Model 3FLANGEC, flange(s) installed in the pump compartment.

There will be a switch accessible through a door on the pump panel included with this installation. 0005599 Gauges, Engine - Pump Panel

PUMP PANEL GAUGES AND CONTROLS
The following will be provided on the pump and gauge panels in a neat and orderly fashion:
- Engine Oil Pressure Gauge: With visual and audible warning - Engine Water Temperature Gauge: With visual and audible warning - Tachometer: Electric
- Master Pump Drain Control
- Voltmeter
Bid #: 716 47
EXHIBIT 1 703
0737730 Throttle, Engine, FRC, Infinity Pro,
ETA400 Series

ENGINE THROTTLE
A Fire Research (FRC) InfinityPRO model ETA400 series remote engine throttle will be installed on the pump operator's panel. The case and control knob will be machined from anodized aluminum, waterproof, and have dimensions not to exceed 2.50" diameter and 4.375" deep. The control knob will be 2.00" in diameter with a serrated grip, no mechanical stops, and have a red idle push button in the center.

The remote engine throttle will set the engine RPM to idle when the pump engaged interlock signal is recognized regardless of the control knob position. It will use optical technology to detect the direction and speed of the control knob when it is rotated.

The control knob will programmed to be used in the clockwise rotation to increase engine speed and counterclockwise to decrease engine speed.
0742051 Indicator Light @ Pump Panel,
Throttle Ready, Green

THROTTLE READY GREEN INDICATOR LIGHT
There will be a green indicator light with label installed on the pump operators panel that is activated when the pump is in Throttle Ready mode.
0007541 Indicator Lights @ Pump Panel,
Electronic Engines
- Check Transmission Warning Indicator Light
- Stop Engine Warning Indicator Light
- Check Engine Warning Indicator Light.
0745568 Indicator Light, Pump Panel, Ok To
Pump, Green

OK TO PUMP INDICATOR LIGHT
There will be a green indicator light installed on the pump operators panel that is activated when the pump is in Ok To Pump mode.
0069390 Control, Air Horn At Pmp Pnl, Red
Button

AIR HORN BUTTON
An air horn control button will be provided at the pump operator's control panel. This button will be red in color and properly labeled and put within easy reach of the operator. 0560441 Grille, Speaker Louvered S/S, Each

STAINLESS STEEL SPEAKER GRILLE
There will be one (1) polished stainless steel grille/s, for a radio speaker/s, provided and installed per the pump panel drawing on the pump panel.

The grille will be constructed with automotive type louvers, so rain and road splash are deflected.

The speaker size will be for a Motorola Remote-Mount, Water-Resistant Speaker part #HSN4040A.
0009666 Pump Master Gauge Panel Mounted
@ Angle

ANGLED GAUGE PANEL
The pump master gauge panel will be mounted at an angle downward to improve visibility of the gauges.
0005690 Gauges, 6.00" Master, Class 1, 30"-0
-600psi

VACUUM AND PRESSURE GAUGES
The pump vacuum and pressure gauges will be liquid filled and manufactured by Class 1 Incorporated ©.

The gauges will be a minimum of 6.00" in diameter and will have white faces with black lettering, with a pressure range of 30.00"-0-600#.

The pump pressure and vacuum gauges will be installed adjacent to each other at the pump operator's control panel.

Test port connections will be provided at the pump operator's panel. One will be connected to the intake side of the pump, and the other to the discharge manifold of the pump. They will have 0.25 in. standard pipe thread connections and polished stainless steel plugs. They will be marked with a label.
0511105 Gauge, 3.00" Pressure, Class 1,
Special

PRESSURE GAUGES
The individual "line" pressure gauges for the discharges will be interlube filled and manufactured by Class 1©.

The gauges will be a minimum of 3.00" in diameter and will have white faces with black markings.

Gauge construction will include a Zytel nylon case with adhesive mounting gasket and threaded retaining nut.

Gauges will have a pressure rating of 0-400 psi.

The individual pressure gauge will be installed as close to the outlet control as practical.

This gauge will include a 10 year warranty against leakage, pointer defect, and defective bourdon tube.

Bid #: 716 48
EXHIBIT 1 704
0757359 Gauge, Water Level, Class 1,
Remote Module Driver

WATER LEVEL GAUGE
There will be an electronic water level gauge provided on the operator's panel that registers water level by means of five (5) colored LED lights. The lights will be durable, ultra-bright five (5) LED design viewable through 180 degrees. The water level indicators will be as follows:
100 percent = Green
75 percent = Yellow
50 percent = Yellow
25 percent = Yellow
Refill = Red
The light will flash when the level drops below the given level indicator to provide an eighth of a tank indication. To further alert the pump operator, the lights will flash sequentially when the water tank is empty.

The level measurement will be based on the sensing of head pressure of the fluid in the tank.

The display will be constructed of a solid plastic material with a chrome plated die cast bezel to reduce vibrations that can cause broken wires and loose electronic components. The encapsulated design will provide complete protection from water and environmental elements. An industrial pressure transducer will be mounted to the outside of the tank. The field calibratable display measures head pressure to accurately show the tank level.

There will be a Hale part number 106877, 4-light driver module included with this installation to power additional water level gauges.

The system(s) will be energized when pump is in gear.
0750438 Water Level Gauge, Wln PSTANK2,
LED 1-Light, 4-Level

WATER LEVEL GAUGE
There will be two (2) additional water level indicator(s), Whelen®, Model PSTANK2, LED module with black trim, installed one (1) each side, forward and up high on the body side sheet post.

This light module(s) will include four (4) colored levels, and function similar to the water level indicator located at the operators panel:

First green module indicates a full water level
Second blue module indicates a water level above 3/4 full Third amber module indicates a water level above 1/2 full Last red module indicates a water level above 1/4 full and empty Above 1/4 this light will be steady burning
At empty this light will be flashing
The flash rate will be determined by the main water level tank sensor.

This module will be activated when the pump is in gear. 0062992 Gauge, Foam Level, (1) Tank, Class
1, GAAAR 5lt

FOAM LEVEL GAUGE
An electronic foam level gauge will be provided on the operator's panel that registers foam level by means of five (5) colored LED lights. The lights will be durable, ultra-bright five (5) LED design viewable through 180 degrees. The foam level indicators will be as follows:
100 percent = Green
75 percent = Yellow
50 percent = Yellow
25 percent = Yellow
Refill = Red
The light will flash when the level drops below the given level indicator to provide an eighth of a tank indication. To further alert the pump operator, the lights will flash sequentially when the foam tank is empty.

The level measurement will be based on the sensing of head pressure of the fluid in the tank.

The display will be constructed of a solid plastic material with a chrome plated die cast bezel to reduce vibrations that can cause broken wires and loose electronic components. The encapsulated design will provide complete protection from foam and environmental elements. An industrial pressure transducer will be mounted to the outside of the tank. The display will be able to be calibrated in the field and will measure head pressure to accurately show the tank level. 0656224 Light Shield/Step 8", S/S Undr Crs,
LED w/P25 LED Step Light

STEP/LIGHT SHIELD
There will be a polished, 16 gauge stainless steel light shield installed under the crosslays. This shield will be properly reinforced to support the crosslay hose weight.

There will be 12 volt DC white LED light(s) installed under the stainless steel light shield.

These lights will be activated when the battery switch is on and the pump panel light switch is on.

There will be an aluminum treadplate stepping surface no less than 8.00" deep and properly reinforced to support a man's weight, installed over the pump operators main panel.

There will be 12 volt DC white LED lights installed under the step to illuminate the controls, switches, essential instructions, gauges, and instruments necessary for the operation of the apparatus. These lights will be activated by the pump panel light switch. Additional lights will be included every 18.00" depending on the size of the pump house.

One (1) pump panel light will come on when the pump is in ok to pump mode.

There will be a light activated above the pump panel light switch when the parking brake is set.

This is to afford the operator some illumination when first approaching the control panel.

There will be one (1) white LED, step light provided above this step. In order to ensure exceptional illumination, each step light will provide a minimum of 25 foot-candles (fc) covering an entire 15" x 15" square placed ten (10) inches below the light and a minimum of 1.5 fc covering an entire 30" x 30" square at the same ten (10) inch distance below the light. The step light will be activated by the pump panel light switch.

Bid #: 716 49
EXHIBIT 1 705
0622038 Light Shield/Step 8" & S/S Under
Xlays, LED, PS, P25 LED Stp Lt

ADDITIONAL STEP/LIGHT SHIELD
There will be a polished, 16 gauge stainless steel light shield installed under the crosslays. This shield will be properly reinforced to support the crosslay hose weight.

There will be two (2) 12 volt DC white LED light(s) installed under the stainless steel light shield.

These lights will be activated when the battery switch is on and the pump panel light switch is on.

There will be an aluminum treadplate stepping surface no less than 8.00" deep and properly reinforced to support a man's weight, installed over the pump panel.

There will be 12 volt DC white LED lights installed under the step to illuminate the controls, switches, essential instructions, gauges, and instruments necessary for the operation of the apparatus. These lights will be activated by the pump panel light switch. Additional lights will be included every 18.00" depending on the size of the pump house.

There will be one (1) white LED, step light provided above this step. In order to ensure exceptional illumination, each step light will provide a minimum of 25 foot-candles (fc) covering an entire 15" x 15" square placed ten (10) inches below the light and a minimum of 1.5 fc covering an entire 30" x 30" square at the same ten (10) inch distance below the light. The step light will be activated by the pump panel light switch.
0606694 Air Horns, (2) Hadley, 6" Round,
eTone, In Bumper

AIR HORN SYSTEM
Two (2) Hadley®, eTone, chrome air horns will be recessed in the front bumper. The air horn system will be piped to the air brake system wet tank utilizing 0.38" tubing. A pressure protection valve will be installed to prevent the loss of air in the brake system. 0606835 Location, Air Horns, Bumper, Each
Side, Outside Frame, Outboard (Pos
#1 & #7)
Air Horn Location
The air horns will be located on each side of the bumper, towards the outside. 0757092 Control, Air Horn, Multi Select

Air Horn Control
The air horn(s) will be activated by the following:
0757081 Control, Air Horn, Ft Sw, LS

Left side foot switch
0723391 Control, Air Horn, Chrome Push
Button Sw, RS
Right side chrome push button switch
0605454 Siren, Wln 295SDA1, 100 or 200
Watt Traf Dir Lt Cnt

ELECTRONIC SIREN
There will be a Whelen®, Model 295SDA1, electronic siren with noise canceling microphone and traffic directing light control provided.

This siren to be activated when the battery switch is on. 0692039 Location, Electronic Siren, Center
Console Electronic siren head will be located in the center console. 0076156 Control, Elec Siren, Head Only The electronic siren will be controlled on the siren head only. No horn button or foot switches will be provided.
0601306 Speaker, (1) Wln, SA315P, w/Pierce
Polished Stainless Steel Grille, 100
watt

SPEAKER
There will be one (1) Whelen®, Model SA315P, black nylon composite, 100-watt, speaker with through bumper mounting brackets and polished stainless steel grille provided. The speaker will be connected to the siren amplifier.
0601552 Location, Speaker, Frt Bumper,
Recessed, Right Side, Outside
Frame,Inbrd (Pos 2)
The speaker will be recessed in the right side of the front bumper, just outside of the frame rail. 0895281 Siren, Federal Q2B, Littelfuse 24213
Sol

AUXILIARY MECHANICAL SIREN
There will be a Federal Signal Model Q2B mechanical siren furnished and installed in the front of the apparatus.

The Q2B siren will be chrome finish.

The siren will have a 2-gauge cable connected to a Littelfuse part number 24213 power solenoid that is connected by a 2-gauge cable ran battery direct to the primary chassis batteries and will be labeled Q2B+ at the battery. The power solenoid will only be enabled when the emergency master switch is on.

The siren will have a 2-gauge ground wire connected to the chassis battery stud. The cable will be labeled Q2B- at the battery.

When the chassis battery switch is on, and the emergency master switch is on, the Q2B siren will be activated by the following:
0006097 Location of Siren, Recessed in
Bumper
The mechanical siren will be recessed in the front bumper on the left side. The siren will be properly supported using the bumper framework.

Bid #: 716 50
EXHIBIT 1 706
0748305 Control, Mech Siren, Multi Select

MECHANICAL SIREN CONTROL
The mechanical siren will be activated by the following:
0748282 Control Mech Siren, Ft Sw LS

Left side foot switch.
0737437 Sw, Siren Brake, Momentary Red,
Pnl 9, Saber FR/Enf
A momentary red switch will be included in switch panel #9 to activate the siren brake. 0746353 Not Required, Warning Lights
Intensity
0778949 Lightbar, Wln, Freedom IV-Q, 72",
RRRRWsrROptRsrWRRRR

FRONT ZONE UPPER WARNING LIGHTS
There will be one (1) 72.00" Whelen® Freedom™ IV LED lightbar mounted on the cab roof.

The lightbar will include the following:

One (1) red flashing LED module in the left side end position.

One (1) red flashing LED module in the left side front corner position.

One (1) red flashing LED module in the left side first front position.

One (1) red flashing LED module in the left side second front position.

One (1) white flashing LED module in the left side third front position.

One (1) red steady burn LED module in the left side fourth front position.

One (1) red flashing LED module in the left side fifth front position.

One (1) 795 LED traffic light controller sent to national standard high priority in the center positions.

One (1) red flashing LED module in the right side fifth front position.

One (1) red steady burn LED module in the right side fourth front position.

One (1) white flashing LED module in the right side third front position.

One (1) red flashing LED module in the right side second front position.

One (1) red flashing LED module in the right side first front position.

One (1) red flashing LED module in the right side front corner position.

One (1) red flashing LED module in the right side end position.

There will be clear lenses included on the lightbar.

The following switches may be installed in the cab on the switch panel to control the lightbar:
a switch to control the flashing LED modules.
the traffic light controller with the emergency master switch only. no momentary switch to activate the traffic light controller.

The two (2) white flashing LED modules and the traffic light controller will be disabled when the parking brake is applied.

The six (6) red flashing LED modules in the front positions may be load managed when the parking brake is applied.
0540384 Lights, Front Zone, Wln M6*C LED,
Clear Lens, in Common Bzl

LIGHTS, FRONT ZONE LOWER
Two (2) Whelen model M6*C LED flashing warning lights will be installed on the cab face above the headlights, in a common bezel with the directional lights.

The driver's side front warning light to be red.

The passenger's side front warning light to be red.

Both lights will include a clear lens.

There will be a switch located in the cab on the switch panel to control the lights. 0063971 Daytime Running Lights, Headlights,
AXT/Saber/Enforcer (Low Beam)

DAYTIME RUNNING LIGHTS (HEADLIGHTS)
The headlights will include a feature for daytime running lights which will be automatically activated when the parking brake is released. The daytime running light feature will be deactivated when the primary headlight switch is turned on, when other headlight options are activated or when the parking brake is set. The running lights will be wired through the low beam head lights.
0653937 Flasher, Headlight Alternating

HEADLIGHT FLASHER
The high beam headlights will flash alternately between the left and right side.

There will be a switch installed in the cab on the switch panel to control the high beam flash. This switch will be live when the battery switch and the emergency master switches are on.

The flashing will automatically cancel when the hi-beam headlight switch is activated or when the parking brake is set.
0540679 Lights, Side Zone Lower, Wln M6*C
LED, Clear Lens 2pr

SIDE ZONE LOWER LIGHTING
There will be four (4) Whelen®, Model M6*C, flashing LED warning lights with chrome trim installed per the following:

Two (2) lights, one (1) each side on the bumper extension. The side front lights to be red.

Two (2) lights, one (1) each side above rear wheels. The side rear lights to be red.

The lights will include a clear lenses.

There will be a switch in the cab on the switch panel to control the lights.

Bid #: 716 51
EXHIBIT 1 707
0895974 Lights, Door Interior Flash, 4 Dr Cab,
Wln 3S*00F*R, 3" Round

INTERIOR CAB DOOR WARNING LIGHTS
There will be four (4) Whelen® Model 3S*00F*R, 3.00" round deep flashing LED warning lights with grommet mounting.

One (1) light(s) to include red flashing LED's on the left side cab door One (1) light(s) to include red flashing LED's on the right side cab door.

One (1) light(s) to include red flashing LED's on the right side crew cab door.

One (1) light(s) to include red flashing LED's on the left side crew cab door.

The lens color(s) to be the same as the LEDs.

Each light will be located in the door pan as low and far to the outside as practical..

Each light will be activated when the battery switch is on, respective door is opened and the EMaster is on. 0895609 Connectors, Door Interior Flash, All
Cabs, Butt Splice

ELECTRICAL CONNECTORS FOR WARNING LIGHTS
The lights will be installed with an insulated crimped factory butt splice connection. 0672937 Lights, Side, Wln WIONSMC* LED,
Chrome Flange, Mounted In Rub
Rail, 1st

SIDE WARNING LIGHTS
There will be four (4) Whelen, Model WIONSMC* LED light(s) provided and located in the body rub rails one (1) each under the following compartments: LS1, LS3, RS1 and RS3. The lights will NOT be mounted with the rubber gasket behind the light which will allow the light(s) to fit in the rub rails.

The color of each light will be red LED with a clear lens.

Each light will be provided with a chrome plated ABS flange.

The light(s) will be activated with the side warning switch. 0564655 Lights, Rear Zn Lwr, Wln M6*C LED,
Clear Lens, For Tail Lt Housing

REAR ZONE LOWER LIGHTING
There will be two (2) Whelen®, Model M6*C, LED flashing warning lights located at the rear of the apparatus.

The driver's side rear light to be red
The passenger's side rear light to be red
Both lights will include a lens that is clear.

There will be a switch located in the cab on the switch panel to control the lights. 0898358 Lights, Rear/Side Up Zone, Wln M9**
M9V2** M9V2** M9** 4lts
WARNING LIGHTS (Rear and Side upper zones)
There will be four (4) Whelen LED lights with chrome trim provided at the rear of the apparatus.

One (1) Model M9**, 6.50" high x 10.37" long x 1.37" deep flashing LED warning light installed on the driver's side, side of the apparatus as high and close to the rear as practical. The side rear upper light(s) on the driver's side to be red.

One (1) Model M9V2**, 6.50" high x 10.38" long x 2.63" deep flashing LED warning light with white scene LEDs installed on the driver's side, rear of the apparatus as high and close to the outside as practical. The rear upper light(s) on the driver's side to be red.

One (1) Model M9V2**, 6.50" high x 10.38" long x 2.63" deep flashing LED warning light with white scene LEDs installed on the passenger's side, rear of the apparatus as high and close to the outside as practical. The rear upper light(s) on the passenger's side to be red.

One (1) Model M9**, 6.50" high x 10.37" long x 1.37" deep flashing LED warning light installed on the passenger's side, side of the apparatus as high and close to the rear as practical.The side rear upper light(s) on the passenger's side to be red.

The flashing warning lights will include a lens that is clear. The scene lights will include a clear lens.

There will be a switch in the cab on the switch panel to control the flashing warning lights.

The scene LEDs will be controlled by a switch at the driver's side switch panel and by a switch at the left side pump panel.

The scene LEDs may be load managed when the parking brake is applied. 0006551 Not Required, Lights, Rear Upper
Zone Blocking
0537807 Mtg, Rear Warn Lts, Side Sheets &
On Rear Bulkheads

REAR LIGHT MOUNTING
The rear warning lights will be mounted on the rear side sheet flange and rear bulkhead of the body as high as possible with all wiring totally enclosed. 0897967 SP Light, Traffic Directing, Wln TAL65,

36.00" Long, TACTL5, Len Color
Feature

TRAFFIC DIRECTING LIGHT
There will be one (1) Whelen®, Model TAL65, 36.00" long x 2.87" high x 2.25" deep, amber LED traffic directing light installed at the rear of the apparatus. The warning light lens color(s) to be clear
The Whelen, Model TACTL5, control head will be included with this installation.

The controller will be energized when the battery switch is on.

The auxiliary flash to be activated when the emergency master switch is on. 0529278 Location, Traf Dir Lt, Surface Mount

This traffic directing light will be surface mounted at the rear of the apparatus. 0530282 Location, Traf Dir Lt Controller,
Overhead Switch Panel DS Right
End
The traffic directing light control head will be located in the driver side overhead switch panel in the right panel position.

Bid #: 716 52
EXHIBIT 1 708
0779722 Receptacle, 15/20A 120V 3-Pr 3-Wr,
NEMA 5-20R SB Dup, 1st, Interior
Body
120 VOLT RECEPTACLE
There will be two (2), 15/20 amp 120 volt AC three (3) wire straight blade duplex receptacle(s) with interior stainless steel wall plate(s), installed RUN WIRES ONLY to RS1 and RS3 on the left inside wall, upper back corner. Leave 5' of extra wire coiled up, final location TBD @ final inspection. The NEMA configuration for the receptacle(s) will be 5-20R.

The receptacle(s) will be powered from the shoreline inlet.

There will be a label installed near the receptacle(s) that state the following:

Line Voltage
Current Ratting (amps)
Phase
Frequency
0519934 Not Required, Brand, Hydraulic Tool
System
0649753 Not Required, PTO Driven Hydraulic
Tool System
0007150 Bag of Nuts and Bolts

LOOSE EQUIPMENT
The following equipment will be furnished with the completed unit:

One (1) bag of chrome, stainless steel, or cadmium plated screws, nuts, bolts and washers, as used in the construction of the unit.
0602516 NFPA Required Loose Equipment,
Pumper, NFPA 2016, Provided by
Fire Department

NFPA REQUIRED LOOSE EQUIPMENT PROVIDED BY FIRE DEPARTMENT The following loose equipment as outlined in NFPA 1901, 2016 edition, section 5.9.3 and 5.9.4 will be provided by the fire department.
800 ft (60 m) of 2.50" (65 mm) or larger fire hose.
400 ft (120 m) of 1.50" (38 mm), 1.75" (45 mm), or 2.00" (52 mm) fire hose.

One (1) handline nozzle, 200 gpm (750 L/min) minimum.

Two (2) handline nozzles, 95 gpm (360 L/min) minimum.

One (1) smoothbore of combination nozzle with 2.50" shutoff that flows a minimum of 250 gpm.

One (1) SCBA complying with NFPA 1981 for each assigned seating position, but not fewer than four (4), mounted in brackets fastened to the apparatus or stored in containers supplied by the SCBA manufacturer.

One (1) spare SCBA cylinder for each SCBA carried, each mounted in a bracket fastened to the apparatus or stored in a specially designed storage space(s).

One (1) first aid kit.

Four (4) combination spanner wrenches.

Two (2) hydrant wrenches.

One (1) double female 2.50" (65 mm) adapter with National Hose threads.

One (1) double male 2.50" (65 mm) adapter with National Hose threads.

One (1) rubber mallet, for use on suction hose connections.

Two (2) salvage covers each a minimum size of 12 ft x 14 ft (3.7 m x 4.3 m).

One (1) traffic vest for each seating position, each vest to comply with ANSI/ISEA 207, Standard for High Visibility Public Safety Vests, and have a five-point breakaway feature that includes two (2) at the shoulders, two (2) at the sides, and one (1) at the front.

Five (5) fluorescent orange traffic cones not less than 28.00" (711 mm) in height, each equipped with a 6.00" (152 mm) retro-reflective white band no more than 4.00" (152 mm) from the top of the cone, and an additional 4.00" (102 mm) retro-reflective white band 2.00" (51 mm) below the

6.00" (152 mm) band.

Five (5) illuminated warning devices such as highway flares, unless the five (5) fluorescent orange traffic cones have illuminating capabilities.

One (1) automatic external defibrillator (AED).

Four (4) ladder belts meeting the requirements of NFPA 1983, Standard on Fire Service Life Safety Rope and System Components (if equipped with an aerial device).

If the supply hose carried does not use sexless couplings, an additional double female adapter and double male adapter, sized to fit the supply hose carried, will be carried mounted in brackets fastened to the apparatus.

If none of the pump intakes are valved, a hose appliance that is equipped with one or more gated intakes with female swivel connection(s) compatible with the supply hose used on one side and a swivel connection with pump intake threads on the other side will be carried. Any intake connection larger than 3.00" (75 mm) will include a pressure relief device that meets the requirements of 16.6.6.

If the apparatus does not have a 2.50" National Hose (NH) intake, an adapter from 2.50" NH female to a pump intake will be carried, mounted in a bracket fastened to the apparatus if not already mounted directly to the intake.

If the supply hose carried has other than 2.50" National Hose (NH) threads, adapters will be carried to allow feeding the supply hose from a 2.50" NH thread male discharge and to allow the hose to connect to a 2.50" NH female intake, mounted in brackets fastened to the apparatus if not already mounted directly to the discharge or intake.
0519913 Not Required, Soft Suction Hose

SOFT SUCTION HOSE
There will be no soft suction hose provided.
0602389 Strainer, Provided by Dealer, Pumper
NFPA 2016 Classification

STRAINER PROVIDED BY DEALER
NFPA 1901, 2016 edition, section 5.8.2.1.1 requires a suction strainer when suction hose is provided.

The strainer is not on the apparatus as manufactured. The dealer will provide the suction strainer.

Bid #: 716 53
EXHIBIT 1 709
0602538 Extinguisher, Dry Chemical, Pumper
NFPA 2016 Class, Provided by Fire
Department

DRY CHEMICAL EXTINGUISHER PROVIDED BY FIRE DEPARTMENT
NFPA 1901, 2016 edition, section 5.9.4 requires one (1) approved dry chemical portable fire extinguisher with a minimum 80-B:C rating mounted in a bracket fastened to the apparatus.

The extinguisher is not on the apparatus as manufactured. The fire department will provide and mount the extinguisher.
0602360 Extinguisher, 2.5 Gal. Pressurized
Water, Pumper NFPA 2016,Provided
by Fire Dept

WATER EXTINGUISHER PROVIDED BY FIRE DEPARTMENT
NFPA 1901, 2016 edition, section 5.9.4 requires one (1) 2.5 gallon or larger water extinguisher mounted in a bracket fastened to the apparatus.

The extinguisher is not on the apparatus as manufactured. The fire department will provide and mount the extinguisher.
0602679 Axe, Flathead, Pumper NFPA 2016
Classification, Provided by Fire
Department

FLATHEAD AXE PROVIDED BY FIRE DEPARTMENT
NFPA 1901, 2016 edition, Section 5.9.4 requires one (1) flathead axe mounted in a bracket fastened to the apparatus.

The axe is not on the apparatus as manufactured. The fire department will provide and mount the axe.
0602667 Axe, Pickhead, Pumper NFPA 2016
Classification, Provided by Fire
Department

PICKHEAD AXE PROVIDED BY FIRE DEPARTMENT
NFPA 1901, 2016 edition, Section 5.9.4 requires one (1) pickhead axe mounted in a bracket fastened to the apparatus.

The axe is not on the apparatus as manufactured. The fire department will provide and mount the axe.

Bid #: 716 54
EXHIBIT 1 710
0741569 Paint Process / Environmental
Requirements, Appleton

PAINT PROCESS
The exterior custom cab and body painting procedure will consist of a seven (7) step finishing process as follows:

Manual Surface Preparation - All exposed metal surfaces on the custom cab and body will be thoroughly cleaned and prepared for painting. Imperfections on the exterior surfaces will be removed and sanded to a smooth finish. Exterior seams will be sealed before painting. Exterior surfaces that will not be painted include; chrome plating, polished stainless steel, anodized aluminum and bright aluminum treadplate.

Chemical Cleaning and Pretreatment - All surfaces will be chemically cleaned to remove dirt, oil, grease, and metal oxides to ensure the subsequent coatings bond well. The aluminum surfaces will be properly cleaned and treated using a high pressure, high temperature 4 step Acid Etch process. The steel and stainless surfaces will be properly cleaned and treated using a high temperature 3 step process specifically designed for steel or stainless. The chemical treatment converts the metal surface to a passive condition to help prevent corrosion.

Surfacer Primer - The Surfacer Primer will be applied to a chemically treated metal surface to provide a strong corrosion protective basecoat. A minimum thickness of 2 mils of Surfacer Primer is applied to surfaces that require a Critical aesthetic finish. The Surfacer Primer is a twocomponent high solids urethane that has excellent sanding properties and an extra smooth finish when sanded.

Finish Sanding - The Surfacer Primer will be sanded with a fine grit abrasive to achieve an ultrasmooth finish. This sanding process is critical to produce the smooth mirror like finish in the topcoat.

Sealer Primer - The Sealer Primer is applied prior to the Basecoat in all areas that have not been previously primed with the Surfacer Primer. The Sealer Primer is a two-component high solids urethane that goes on smooth and provides excellent gloss hold out when topcoated.

Basecoat Paint - Two coats of a high performance, two component high solids polyurethane basecoat will be applied. The Basecoat will be applied to a thickness that will achieve the proper color match. The Basecoat will be used in conjunction with a urethane clear coat to provide protection from the environment.

Clear Coat - Two (2) coats of Clear Coat will be applied over the Basecoat color. The Clear Coat is a two-component high solids urethane that provides superior gloss and durability to the exterior surfaces. Lap style and roll-up doors will be Clear Coated to match the body. Paint warranty for the roll-up doors will be provided by the roll-up door manufacturer.

After the cab and body are painted, the color will be verified to make sure that it matches the color standard. Electronic color measuring equipment will be used to compare the color sample to the color standard entered into the computer. Color specifications will be used to determine the color match. A Delta E reading will be used to determine a good color match within each family color.

All removable items such as brackets, compartment doors, door hinges, and trim will be removed and painted separately if required, to ensure paint behind all mounted items. Body assemblies that cannot be finish painted after assembly will be finish painted before assembly.

The paint finish quality levels for critical areas of the apparatus (cab front and sides, body sides and doors, and boom lettering panels) are to meet or exceed Cadillac/General Motors GMW15777 global paint requirements. Orange peel levels are to meet or exceed the #6 A.C.T.standard in critical areas. The manufacture's written paint standards will be available upon request.

Environmental Impact
Contractor will meet or exceed all current state regulations concerning paint operations. Pollution control will include measures to protect the atmosphere, water and soil. Controls will include the following conditions:

Topcoats and primers will be chrome and lead free.

Metal treatment chemicals will be chrome free. The wastewater generated in the metal treatment process will be treated on-site to remove any other heavy metals.

Particulate emission collection from sanding operations will have a 99.99 percent efficiency factor.

Particulate emissions from painting operations will be collected by a dry filter or water wash process. If the dry filter is used, it will have an efficiency rating of 98 percent. Water wash systems will be 99.97 percent efficient
Water from water wash booths will be reused. Solids will be removed on a continual basis to keep the water clean.

Paint wastes are disposed of in an environmentally safe manner.

Empty metal paint containers will be recycled to recover the metal.

Solvents used in clean-up operations will be recycled on-site or sent off-site for distillation and returned for reuse.

Additionally, the finished apparatus will not be manufactured with or contain products that have ozone depleting substances. Contractor will, upon demand, present evidence that the manufacturing facility meets the above conditions and that it is in compliance with his state EPA rules and regulations.
0709567 Paint, Single Color, Enforcer

CAB PAINT
The cab will be painted #219 Red.
0709845 Paint, Single Color, Body

BODY PAINT
The body will be painted to match the lower section of the cab.

Bid #: 716 55
EXHIBIT 1 711
0646901 Paint Chassis Frame Assy, With
Liner, E-Coat, Standard

PAINT CHASSIS FRAME ASSEMBLY
The chassis frame assembly will be finished with a single system black top coat before the installation of the cab and body, and before installation of the engine and transmission assembly, air brake lines, electrical wire harnesses, etc.

Components that are included with the chassis frame assembly that will be painted are:

Frame rails
Frame liners
Cross members
Axles
Suspensions
Steering gear
Battery boxes
Bumper extension weldment
Frame extensions
Body mounting angles
Rear Body support substructure (front and rear)
Pump house substructure
Air tanks
Steel fuel tank
Castings
Individual piece parts used in chassis and body assembly Components treated with epoxy E-coat protection prior to paint:

Two (2) C-channel frame rails
Two (2) frame liners
The E-coat process will meet the technical properties shown. 0693797 No Paint Required, Aluminum Front
Wheels
0693792 No Paint Required, Aluminum Rear
Wheels
0733739 Paint, Axle Hubs

AXLE HUB PAINT
All axle hubs will be painted to match lower job color. 0007234 Compartment, Unpainted, D/A
Finished

COMPARTMENT INTERIOR FINISH
The interior of the compartments will be dual action finished and not painted. 0544074 Reflective Band, 4"

REFLECTIVE BAND
A 4.00" black reflective band will be provided across the front of the vehicle and along the sides of the body.
0007356 Reflective across Cab Face

The reflective band provided on the cab face will be at the headlight level. 0602763 Stripe, Chevron, Rear, Reflective,
Non-NFPA 2016 Colors, Pumper

REAR CHEVRON STRIPING
There will be alternating chevron striping located on the rear-facing vertical surface of the apparatus. The rear surface, excluding the rear compartment door, will be covered.

The colors will be ruby red and black reflective.

Each stripe will be 6.00" in width.

This will meet the requirements of NFPA 1901, 2016 edition, which states that 50 percent of the rear surface will be covered with chevron striping.

NFPA 1901, 2016 edition, Section 15.9.3.2.1 requires each stripe in the chevron to be a single color alternating between red and either yellow, fluorescent yellow, or fluorescent yellow green.

Use of the red and yellow color is endorsed by the International Association of Fire Chiefs. The fire apparatus purchaser will realize that by requesting an exception to this aspect of NFPA 1901, this fire apparatus will not contribute to the national standardization initiative. Per the purchaser's specification, this apparatus will not be compliant to NFPA 1901 standards in this regard. 0065687 Stripe, Reflective, Cab Doors Interior

CAB DOOR REFLECTIVE STRIPE
A 6.00" x 16.00" black reflective stripe will be provided across the interior of each cab door. The stripe will be located approximately 1.00" up from the bottom, on the door panel.

This stripe will meet the NFPA 1901 requirement.
0594559 Lettering Specifications, (Sign Gold
Process)

LETTERING
The lettering will be 22 karat gold vinyl.
0685908 Lettering, Sign Gold, 4.00", (61-80)

LETTERING
Sixty-one (61) to eighty (80) Sign Gold lettering, 4.00" high, with outline and shade will be provided.

Bid #: 716 56
EXHIBIT 1 712
0686007 Lettering, Reflective, 7.00", Each

LETTERING
There will be reflective lettering, 7.00" high, with outline and shade provided. There will be four (4) letters provided.
0655896 Sign Kit, Painted, Holder and Insert,
Each

SIGN KIT FOR LETTERING/NUMERALS
four (4) painted stainless steel plate(s) and holder(s) will be provided for department lettering.

They will be mounted at final inspection and 12"W x 10"H in size. 0017268 Decals, Customer furnished, Pierce
installed, Per Pair

DECAL INSTALLATION
There will be one (1) pair of decals furnished by the fire department and applied by the apparatus manufacturer.
0772003 Manual, Fire Apparatus Parts, USB
Flash Drive, Custom

FIRE APPARATUS PARTS MANUAL
There will be one (1) custom parts manual(s) in USB flash drive format for the complete fire apparatus provided.

The manual(s) will contain the following:

Job number
Part numbers with full descriptions
Table of contents
Parts section sorted in functional groups reflecting a major system, component, or assembly Parts section sorted in alphabetical order
Instructions on how to locate parts
Each manual will be specifically written for the chassis and body model being purchased. It will not be a generic manual for a multitude of different chassis and bodies.

Service Parts Internet Site
The service parts information included in these manuals are also available on the Pierce website.

The website offers additional functions and features not contained in this manual, such as digital photographs and line drawings of select items. The website also features electronic search tools to assist in locating parts quickly.
0772037 Manual, Chassis Service, USB Flash
Drive, Custom

CHASSIS SERVICE MANUALS
There will be one (1) chassis service manuals on USB flash drives containing parts and service information on major components provided with the completed unit.

The manual will contain the following sections:

Job number
Table of contents
Troubleshooting
Front Axle/Suspension
Brakes
Engine
Tires
Wheels
Cab
Electrical, DC
Air Systems
Plumbing
Appendix
The manual will be specifically written for the chassis model being purchased. It will not be a generic manual for a multitude of different chassis and bodies. 0773381 Manual, Chassis Operation, (1) USB
Flash Drive, Custom

CHASSIS OPERATION MANUAL
The chassis operation manual will be provided on one (1) USB flash drive. 0030008 Warranty, Basic, 1 Year, Apparatus,
WA0008
ONE (1) YEAR MATERIAL AND WORKMANSHIP
A Pierce basic apparatus limited warranty certificate, WA0008, is included with this proposal. 0696698 Warranty, Engine, Cummins, 5 Year,
WA0181

ENGINE WARRANTY
A Cummins five (5) year limited engine warranty will be provided. A limited warranty certificate, WA0181, is included with this proposal.
0684952 Warranty, Steering Gear, TRW Ross
TAS, 1 Year WA0202