Agenda packet — Beaumont City Council, July 21, 2026 (part 18 of 20)

SHERWIN
WILLIAMS®

SPECIFICATIONS
Steel*
2 coats Pro Industrial DTM Acrylic
Steel:
1 coat Pro Industrial Pro-Cryl Primer
or Pro Industrial DTM Primer/Finish
or Pro Industrial Kem Bond HS Metal Primer
or Zinc Clad Primer
1-2 coats Pro Industrial DTM Acrylic
Aluminum:
1-2 coats Pro Industrial DTM Acrylic
Aluminum (Water Based Primer):
1 coat Pro Industrial Pro-Cryl Primer
1-2 coats Pro Industrial DTM Acrylic
Concrete Block (CMU):
1 coat Pro Industrial Heavy Duty Block Filler
or Loxon Acrylic Block Surfacer
2 coats Pro Industrial DTM Acrylic
Concrete -Masonry:
1 coat Loxon Concrete & Masonry Primer
or 1 coat Loxon Conditioner
2 coats Pro Industrial DTM Acrylic
Drywall:
1 coat ProMar 200 Zero V.O.C. Primer
1-2 coats Pro Industrial DTM Acrylic
Galvanizing:
2 coats Pro Industrial DTM Acrylic
Pre -Finished Siding: (Baked -on finishes)
1 coat Pro Industrial Bond-Plex Waterbased
Acrylic
or Pro Industrial DTM Bonding Primer
1-2 coats Pro Industrial DTM Acrylic
Wood, exterior:
1 coat Exterior Wood Primer
1-2 coats Pro Industrial DTM Acrylic
Wood, interior:
1 coat Premium Wall & Wood Primer
1-2 coats Pro Industrial DTM Acrylic
*Application of coating on unprimed steel may cause
pinpoint rusting. Safety Colors, Deep Base, and
Ultradeep colors require a prime coat for maximum
durability, adhesion, and corrosion protection.

Zinc Primers — Refer to the zinc technical data
sheet application procedures and performance
tips prior to topcoating.
continued on back

Pro Industrial' DTM
Acrylic Semi -Gloss

SURFACE PREPARATION
WARNING! If you scrape, sand or remove old paint,
you may release lead dust. LEAD IS TOXIC.

EXPOSURE TO LEAD DUST CAN CAUSE

SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE,
ESPECIALLY IN CHILDREN. PREGNANT WOMEN
SHOULD ALSO AVOID EXPOSURE. Wear a
NIOSH-approved respirator to control lead
exposure. Clean up carefully with a HEPA vacuum
and a wet mop. Before you start, find out how to
protect yourself and your family by contacting the
National Lead Information Hotline at 1 -800 -424 -
LEAD or log on to www.epa.gov/lead .

Do not use hydrocarbon solvents for cleaning.

Remove all surface contamination by washing with an
appropriate cleaner, rinse thoroughly and allow to dry.

Existing peeled or checked paint should be scraped
and sanded to a sound surface. Glossy surfaces
should be sanded dull. Stains from water, smoke, ink,
pencil, grease, etc. should be sealed with the
appropriate primer -sealer. Recognize that any surface
preparation short of total removal of the old coating
may compromise the service length of the system.

Iron & Steel - Minimum surface preparation is Hand
Tool Clean per SSPC-SP2. Remove all oil and grease
from surface per SSPC-SP1. For better performance,
use Commercial Blast Cleaning per SSPC-SP6.

Primer recommended for best performance.

Aluminum - Remove all oil, grease, dirt, oxide, and
other foreign material per SSPC-SP1.

Galvanizing - Allow to weather a minimum of six
months prior to coating. Solvent Clean per SSPC-
SP1. When weathering is not possible, or the surface
has been treated with chromates or silicates, first
Solvent Clean per SSPC-SP1 and apply a test patch.

Allow paint to dry at least one week before testing
adhesion. If adhesion is poor, brush blasting per
SSPC-SP16 is necessary to remove these
treatments. Rusty galvanizing requires a minimum of
Hand Tool Cleaning per SSPC-SP2. Prime the area
the same day as cleaned.

Concrete Block - Surface should be thoroughly clean
and dry. Air, material, and surface temperatures must
be at least 55°F (13°C) before filling. Use Pro Industrial Heavy Duty Block Filler or Loxon Acrylic Block
Surfacer. The filler must be thoroughly dry before
topcoating.

Masonry — All masonry must be free of dirt, oil, grease, loose paint, mortar, masonry dust, etc. Clean per SSPC- SP13/Nace 6/ ICRI No. 310.2R, CSP 1-3. Poured,
troweled, or tilt -up concrete, plaster, mortar, etc. must be thoroughly cured at least 30 days at 75°F. Form
release compounds and curing membranes must be
removed by brush blasting. Brick must be allowed to
weather for one year prior to surface preparation and
painting. Prime the area the same day as cleaned.

Weathered masonry and soft or porous cement board
must be brush blasted or power tool cleaned to remove
loosely adhering contamination and to get to a hard, firm surface. Apply one coat Loxon Conditioner, following
label recommendations.

Wood - Surface must be clean, dry, and sound. Prime
with recommended primer. No painting should be done
immediately after a rain or during foggy weather. Knots and pitch streaks must be scraped, sanded and spot
primed before full coat of primer is applied. All nail holes or small openings must be properly caulked. Sand to
remove any loose or deteriorated surface wood and to
obtain a proper surface profile.

SURFACE PREPARATION
Previously Painted Surface - If in sound condition,
clean the surface of all foreign material. Smooth,
hard or glossy coatings and surfaces should be
dulled by abrading the surface. Apply a test area,
allowing paint to dry one week before testing
adhesion. If adhesion is poor, additional abrasion of
the surface and/or removal of the previous coating
may be necessary. Retest surface for adhesion. If
paint is peeling or badly weathered, clean surface
to sound substrate and treat as a new surface as
above. Recognize that any surface preparation
short of total removal of the old coating may
compromise the service length of the system.

Mildew - Clean mildew from the Surface: Mildew
is a fungus that looks like dirt but won't wash off.

Mildew must be removed before painting, or it will
grow through any new coat of paint. To remove
mildew or suspected mildew, scrub surface
before painting with a commercial mildew
remover following manufacturer's safety
instructions.

PERFORMANCE
System Tested: (unless otherwise indicated)
Substrate: Steel
Surface Preparation SSPC-SP10
Finish: 2 coats Pro Industrial DTM Acrylic
B66W03151, 3.0 D.F.T per coat
Adhesion:

Method:

Result:

ASTM D4541
1400 p.s.i.

Corrosion Weathering*:

Method: ASTM D5894, 7 cycles
Result: Rating 10 per ASTM D714 for blistering
Rating 8.5 per ASTM D1654 for corrosion
Direct Impact Resistance:

Method: ASTM D2794
Result: greater than 176 inch pound
Dry Heat Resistance:

Method:

Result:

Flexibility:

Method:

Result:

ASTM D2485
300°F
ASTM D522, 1/8 inch mandrel
Pass
Humidity Resistance*:

Method: ASTM D4585, 2016 hours
Result: Rating 10 per ASTM D714 for blistering
Rating 10 per ASTM D1654 for corrosion
Pencil Hardness:

Method:

Result:
*over Pro Industrial Pro-Cryl Primer.

ASTM D3363
2H
No painting should be done immediately after a rain
or during foggy weather.

Do not paint on wet surfaces.

Check adhesion by applying a test strip to determine
the readiness for painting.

Provides performance comparable to products
formulated in lieu of federal specification: AA50570,
and Paint Specification: SSPC-Paint 24.

SAFETY PRECAUTIONS
Before using, carefully read CAUTIONS on label.

Refer to the Safety Data Sheets (SDS) before
use.

FOR PROFESSIONAL USE ONLY.

Published technical data and instructions are
subject to change without notice. Contact your
Sherwin-Williams representative for additional
technical data and instructions.

CLEANUP INFORMATION
Clean spills, spatters, hands and tools
immediately after use with soap and warm clean
water. After cleaning, flush spray equipment with
compliant cleanup solvent to prevent rusting of
the equipment. Follow manufacturer's safety
recommendations when using solvents.

HOTW 03/16/2026 B66W03151 02 36

FRC, SP
The information and recommendations set forth in this Product Data Sherlpf s t rjpl d by or on behalf of The Sherwin-Williams Company. Such information and recommendations set forth herein are subject to change and pertain7Ptife produc o ere a e time of publication. Consult your Sherwin-Williams representative or visit www.paintdocs.com to obtain the most current version of the PDS and/or an SDS

113.12SGA
Pro IndustrialTM
Waterbased Alkyd Urethane Enamel Semi -Gloss
B53-5150 Series

CHARACTERISTICS
Pro Industrial Waterbased Alkyd Urethane
Enamel is a premium quality interior -exterior
enamel formulated with a urethane modified
alkyd resin system for high performance. It
provides beauty and durability when applied to
interior -exterior surfaces such as properly
prepared drywall, wood, masonry, and metal. It
brings together the convenience and ease of use
of a waterborne coating with the performance and
coating characteristics of a traditional oil -based
enamel.
• Excellent washability, flow and leveling
• Excellent touch up
• Easy application & cleanup
• Resistant to yellowing compared to
traditional alkyds
• Suitable for use in USDA inspected
facilities
For use on properly prepared: Steel,
Galvanized & Aluminum, Drywall, Concrete and
Masonry, and Wood.

Finish:

Color:
50-70 units @ 60°
Most Colors
Recommended Spreading Rate per coat:

Wet mils: 4.0-5.0
Dry mils: 1.3-1.7
Coverage: 320-407 sq. ft. per gallon
Theoretical Coverage: 529 sq. ft. per gallon
@ 1 mil dry
Approximate spreading rates are calculated on volume
solids and do not include any application loss.

Note: Brush or roll application may require multiple coats to achieve maximum film thickness and uniformity of
appearance.

Drying Schedule @ 4M mils wet, @ 50% RH:

Drying and recoat times are temperature, humidity, and
film thickness dependent.
@77°F
To touch 1-2 hours
To recoat 4 hours
Tinting with CCE only:

Base oz. per gallon
Extra White 0-6
Deep Base 4-12
Ultradeep Base 10-14
Strength
SherColor
SherColor
SherColor
Extra White B53W05151
(may vary by color)
V.O.C. (less exempt solvents):
less than 50 grams per litre; 0.42 lbs. per gallon
As per 40 CFR 59.406
Volume Solids: 33 ±2%
Weight Solids: 48 ±2%
Weight per Gallon: 10.64 Ibs
Flash Point: N.A.

Vehicle Type: Urethane Modified Alkyd
Shelf Life: 36 months, unopened

COMPLIANCE
As of 04/01/2025, Complies with:

OTC
OTC Phase II
S.C.A.Q.M.D.

CARB
CARB SCM 2007
CARB SCM 2020
Canada
LEED® v4 & v4.1 Emissions
LEED® v4 & v4.1 V.O.C.

EPD-NSF® Certified
MIR-Manufacturer Inventory
MPI®

APPLICATION
Temperature:
minimum
maximum
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
No
#169
50°F / 10°C
100°F / 37.8°C
air, surface and material
At least 5°F above dew point
Relative humidity: 85% maximum
The following is a guide. Changes in pressures and tip
sizes may be needed for proper spray characteristics.

Always purge spray equipment before use with listed
reducer. Any reduction must be compatible with the
existing environmental and application conditions.

Reducer: Water
Airless Spray:

Pressure
Hose
Tip
Filter
Reduction:
2000 p.s.i.
1/4 inch I.D.
.013-.017 inch
60 mesh
Not recommended
Brush: Use a nylon -polyester brush such as
Purdy® Syntox®.

Roller Cover: Use a 1/4-1/2 inch woven cover
such as Purdy® White Dove".

If specific application equipment is listed above,
equivalent equipment may be substituted.

Apply paint at the recommended film thickness
and spreading rate as indicated. Application of
coating above maximum or below minimum
recommended spreading rate may adversely
affect coating performance.

No painting should be done immediately after a
rain or during foggy weather.

When using spray equipment, use a 50% overlap
with each pass of the gun to avoid holidays, bare
areas, and pinholes. Apply coating evenly while
maintaining a wet edge to prevent lapping.

SHERWIN
WILLIAMS®

SPECIFICATIONS
Steel:
1 coat Pro Industrial Pro-Cryl Primer
2 coats Pro Industrial Waterbased Alkyd Urethane
Aluminum & Galvanizing:
1 coat Pro Industrial Pro-Cryl Primer
2 coats Pro Industrial Waterbased Alkyd Urethane
Concrete Block (CMU):
1 coat Pro Industrial Heavy Duty Block Filler
or Loxon Acrylic Block Surfacer
2 coats Pro Industrial Waterbased Alkyd Urethane
Concrete -Masonry:
1 coat Loxon Concrete & Masonry Primer
or 1 coat Loxon Conditioner
2 coats Pro Industrial Waterbased Alkyd Urethane
Drywall:
1 coat ProMar 200 Zero V.O.C. Primer
2 coats Pro Industrial Waterbased Alkyd Urethane
Wood, exterior:
1 coat Exterior Wood Primer
2 coats Pro Industrial Waterbased Alkyd Urethane
Wood, interior:
1 coat Premium Wall & Wood Primer
2 coats Pro Industrial Waterbased Alkyd Urethane
The systems listed above are representative of the
product's use, other systems may be appropriate.
04/2025
www.sherwin-williams.com

Page 1934 of 2226 ends

continued on back

Pro Industrial'
Waterbased Alkyd Urethane Enamel Semi -Gloss

SURFACE PREPARATION
WARNING! If you scrape, sand or remove old paint,
you may release lead dust. LEAD IS TOXIC.

EXPOSURE TO LEAD DUST CAN CAUSE

Do not use hydrocarbon solvents for cleaning.

Remove all surface contamination by washing with an
appropriate cleaner, rinse thoroughly and allow to dry.

Iron & Steel - Minimum surface preparation is Hand
Tool Clean per SSPC-SP2. Remove all oil and grease
from surface per SSPC-SP1. For better performance,
use Commercial Blast Cleaning per SSPC-SP6.

Primer recommended for best performance.

Aluminum - Remove all oil, grease, dirt, oxide, and
other foreign material per SSPC-SP1. Prime the area
the same day as cleaned.

SURFACE PREPARATION
Previously Painted Surface - If in sound condition,
clean the surface of all foreign material. Smooth, hard or glossy coatings and surfaces should be dulled by
abrading the surface. Apply a test area, allowing paint to dry one week before testing adhesion. If adhesion is poor, additional abrasion of the surface and/or removal of the previous coating may be necessary. Retest
surface for adhesion. If paint is peeling or badly
weathered, clean surface to sound substrate and treat
as a new surface as above. Recognize that any surface
preparation short of total removal of the old coating
may compromise the service length of the system.

Mildew - Clean mildew from the Surface: Mildew is a
fungus that looks like dirt but won't wash off. Mildew
must be removed before painting, or it will grow
through any new coat of paint. To remove mildew or
suspected mildew, scrub surface before painting
with a commercial mildew remover following
manufacturer's safety instructions.

PERFORMANCE
System Tested: (unless otherwise indicated)
Substrate: Steel
Surface Preparation SSPC-SP10
Finish: Pro Industrial Waterbased Alkyd Urethane
@5.0 W.F.T.

Adhesion:

Method:

Result:

Pencil Hardness:

Method:

Result:

ASTM D3359 method B
4B
ASTM D3363
4H
Flexibility:

Method: ASTM D522, 180° bend, 1/8 inch mandrel
Result: Pass
Dry Heat Resistance:

Method:

Result:

Block Resistance:

Method:

Result:

Resistance Yellowing:

Method:

Result:

ASTM D2485
200°F
Lab assessment
Excellent
Lab assessment
Excellent
No painting should be done immediately after a rain
or during foggy weather.

Do not paint on wet surfaces.

Check adhesion by applying a test strip to determine
the readiness for painting.

SAFETY PRECAUTIONS
Before using, carefully read CAUTIONS on label.

Refer to the Safety Data Sheets (SDS) before
use.

FOR PROFESSIONAL USE ONLY.

Published technical data and instructions are
subject to change without notice. Contact your
Sherwin-Williams representative for additional
technical data and instructions.

CLEANUP INFORMATION
Clean spills, spatters, hands, and tools
immediately after use with soap and warm clean
water. After cleaning, flush spray equipment with
compliant cleanup solvent to prevent rusting of
the equipment. Follow manufacturer's safety
recommendations when using solvents.

Danger: Rags, steel wool, other waste soaked
with this product, and sanding residue may
spontaneously catch fire if improperly discarded.

Immediately place rags, steel wool, other waste
soaked with this product, and sanding residue in
a sealed, water -filled, metal container. Dispose of
in accordance with local fire regulation.

HOTW 04/01/2025 B53W05151 06 28

Environmental Data Sheets

Page 1936 of 2226 ends

ENVIRONMENTAL DATA SHEET
(Certified Product Data Sheet)
52 00 [2565]

PRODUCT NUMBER
B51 W620

PRODUCT NAME
ProBlock® Premium AII-Purpose Water -Based Interior/Exterior Primer, White

MANUFACTURER'S NAME

THE SHERWIN-WILLIAMS COMPANY
1 Sherwin Way
Cleveland, OH 44113
Date of Preparation
Apr 13, 2026
This document includes all data required by 40 CFR 63.801(a) for a Certified Product Data Sheet under criteria specified in 40 CFR 63.805(a).

AII data given below are MAXIMUM THEORETICAL VALUES based on the product AS CURRENTLY FORMULATED and rely on information provided to us by our raw material suppliers. Our suppliers often provide an estimated value or range less than a certain upper limit. We calculate MAXIMUM THEORETICAL VALUES using defined values, if provided, or the upper limit reported by our supplier. Additionally, the suppliers' information may include amounts present in the product as unintentional byproducts or impurities. Variations may occur in individual batches due to adjustments made during production.

Hazard Category (for SARA 311.312)
B51 W620 = I Acute I Chronic
Product Weight

10.89 lb/gal
Volatile Ingredients
Chemical / Compound
SARA 302 EHS
CERCLA
HAPS 112
% by Weight
% by Volume
Water
7732-18-5
N
N
N
48 65
Specific Gravity

1.31 FLASH POINT
N.A.

Volatile Organic Compounds - U.S. EPA / Canada
B51 W620
LB/Gal
g/L
Coating Density

10.89 1304
By wt
By vol
Total Volatiles

48.4%

64.9%
Federally exempt solvents
Water

48.3%

64.7%
Non -Organic Volatiles
Ammonium Hydroxide

0.1%

0.2%
Organic Volatiles

0.0%

0.0%
Percent Non -Volatile

51.6%

35.1%
VOC Content
LB/Gal
g/L
Total

0.00 0
Less exempt solvents

0.00 0
Of solids

0.00 Ib/Ib

0.00 kg/kg
By wt
By wt LVP-VOC

0.0%
Maximum Incremental Reactivity (MIR) (per US EPA Aerosol Ctg Rule, MIR Values 2009) 0.00

Page 1937 of 2226 ends

page 1 of 3

B51 W620
Volatile Organic Compounds - California
B51 W620
LB/Gal
g/L
Coating Density

10.89 1304
By wt
By vol
Total Volatiles

48.4%

64.9%
Exempt solvents
Water

48.3%

64.7%
Non -Organic Volatiles
Ammonium Hydroxide

0.1%

0.2%
Organic Volatiles

0.0%

0.0%
Percent Non -Volatile

51.6%

35.1%
VOC Content
LB/Gal
g/L
Total

0.00 0
Less exempt solvents

0.00 0
Of solids

0.00 Ib/Ib

0.00 kg/kg
By wt
By wt LVP-VOC

0.0%
Maximum Incremental Reactivity (MIR) (per California Air Resources Board Aerosol Products Regulation, MIR Values 2010) 0.00 Volatile Organic Compounds - South Coast Air Quality Management District, California, US B51 W620
LB/Gal
g/L
Coating Density

10.89 1304
By wt
By vol
Total Volatiles

48.4%

64.9%
Exempt solvents
Water

48.3%

64.7%
Non -Organic Volatiles
Ammonium Hydroxide

0.1%

0.2%
Organic Volatiles

0.0%

0.0°/0
Percent Non -Volatile

51.6%

35.1%
VOC Content
LB/Gal
g/L
Total

0.00 0
Less exempt solvents

0.00 0
Of solids

0.00 Ib/Ib

0.00 kg/kg
Volatile Organic Compounds - EU Directive 2004/42/EC
B51 W620
By wt
By vol
Total Volatiles

48.4%

64.9%
VOC Content
LB/Gal
g/L
Total

0.00 0

Page 1938 of 2226 ends

page 2 of 3

B51 W620
Volatile Organic Compounds - EU Directive 2010/75/EU
B51 W620
By wt
By vol
Total Volatiles

48.4%

64.9%
VOC Content
LB/Gal
g/L
Total

0.00 0
Volatile Organic Compounds - Mexico
B51W620
LB/Gal
g/L
Coating Density

10.89 1304
By wt
By vol
Total Volatiles

48.4%

64.9%
Exempt solvents
Water

48.3%

64.7%
Non -Organic Volatiles
Ammonium Hydroxide

0.1%

0.2%
Organic Volatiles

0.0%

0.0°/0
Percent Non -Volatile

51.6%

35.1%
VOC Content
LB/Gal
g/L
Total

0.00 0
Less exempt solvents

0.00 0
Of solids

0.00 Ib/Ib

0.00 kg/kg
Hazardous Air Pollutants (Clean Air Act, Section 112(b)) B51W620
LB/Gal
kg/L
Volatile HAPS

0.00 0.000
Of solids

0.00 Ib/Ib

0.00 kg/kg
Air Quality Data
Density of Organic Solvent Blend

6.27 lb/gal
Photochemically Reactive
No
Waste Disposal
Waste from this product is not hazardous as defined under the Resource Conservation and Recovery Act (RCRA) 40 CFR 261.

The addition of any material to this product can change the composition, hazards and risks of the product and may substantially alter the above data. Since conditions of use are outside our control, we make no warranties, express or implied, and assume no liability in connection with any use of this information.

Page 1939 of 2226 ends

page 3 of 3

ENVIRONMENTAL DATA SHEET
(Certified Product Data Sheet)
21 00 [0616]

PRODUCT NUMBER
A82W351

PRODUCT NAME
A-100® Exterior Satin Latex Paint, Extra White

MANUFACTURER'S NAME

THE SHERWIN-WILLIAMS COMPANY
1 Sherwin Way
Cleveland, OH 44113
Date of Preparation
Apr 14, 2026
This document includes all data required by 40 CFR 63.801(a) for a Certified Product Data Sheet under criteria specified in 40 CFR 63.805(a).

All data given below are MAXIMUM THEORETICAL VALUES based on the product AS CURRENTLY FORMULATED and rely on information provided to us by our raw material suppliers. Our suppliers often provide an estimated value or range less than a certain upper limit. We calculate MAXIMUM THEORETICAL VALUES using defined values, if provided, or the upper limit reported by our supplier. Additionally, the suppliers' information may include amounts present in the product as unintentional byproducts or impurities. Variations may occur in individual batches due to adjustments made during production.

Hazard Category (for SARA 311.312)
A82W351 = I Acute I Chronic
Product Weight

9.84 lb/gal
Volatile Ingredients
Chemical / Compound
SARA 302 EHS
CERCLA
HAPS 112
% by Weight
% by Volume
Water
7732-18-5
N
N
N
56 65
Specific Gravity

1.18 FLASH POINT
N.A.

Regulated Compounds
SARA 302 EHS
CERCLA
HAPS 112
by Weight
% by Volume
Zinc (as Zn)
N
Y
N
2 Volatile Organic Compounds - U.S. EPA / Canada
A82W351
LB/Gal
g/L
Coating Density

9.84 1179
By wt
By vol
Total Volatiles

57.1%

67.0%
Federally exempt solvents
Water

55.7%

65.4%
Organic Volatiles

1.3%

1.5%
Percent Non -Volatile

42.9%

33.0%
VOC Content
LB/Gal
g/L
Total

0.12 15
Less exempt solvents

0.36 43
Of solids

0.38 46
Of solids

0.03 Ib/Ib

0.03 kg/kg
By wt
By wt LVP-VOC

0.0%
Maximum Incremental Reactivity (MIR) (per US EPA Aerosol Ctg Rule, MIR Values 2009) 0.02

Page 1940 of 2226 ends

page 1 of 3

A82W351
Volatile Organic Compounds - California
A82W351
LB/Gal
g/L
Coating Density

9.84 1179
By wt
By vol
Total Volatiles

57.1%

67.0%
Exempt solvents
Water

55.7%

65.4%
Organic Volatiles

1.3%

1.5%
Percent Non -Volatile

42.9%

33.0%
VOC Content
LB/Gal
g/L
Total

0.12 15
Less exempt solvents

0.36 43
Of solids

0.38 46
Of solids

0.03 Ib/Ib

0.03 kg/kg
By wt
By wt LVP-VOC

0.0%
Maximum Incremental Reactivity (MIR) (per
California Air Resources Board Aerosol Products Regulation, MIR Values 2010) 0.02 Volatile Organic Compounds
- South Coast Air Quality Management District, California, US A82W351
LB/Gal
g/L
Coating Density

9.84 1179
By wt
By vol
Total Volatiles

57.1%

67.0%
Exempt solvents
Water

55.7%

65.4%
Organic Volatiles

1.3%

1.5%
Percent Non -Volatile

42.9%

33.0%
VOC Content
LB/Gal
g/L
Total

0.12 15
Less exempt solvents

0.36 43
Of solids

0.38 46
Of solids

0.03 Ib/Ib

0.03 kg/kg
Volatile Organic Compounds - EU Directive 2004/42/EC
A82W351
By wt
By vol
Total Volatiles

56.6%

66.4%
VOC Content
LB/Gal
g/L
Total

0.07 9
Volatile Organic Compounds - EU Directive 2010/75/EU
A82W351
By wt
By vol
Total Volatiles

56.6%

66.4%
VOC Content
LB/Gal
g/L
Total

0.07 9

Page 1941 of 2226 ends

page 2 of 3

A82W351
Volatile Organic Compounds - Mexico
A82W351
LB/Gal
g/L
Coating Density

9.84 1179
By wt
By vol
Total Volatiles

57.1%

67.0%
Exempt solvents
Water

55.7%

65.4%
Organic Volatiles

1.3%

1.5%
Percent Non -Volatile

42.9%

33.0%
VOC Content
LB/Gal
g/L
Total

0.12 15
Less exempt solvents

0.36 43
Of solids

0.38 46
Of solids

0.03 Ib/Ib

0.03 kg/kg
Hazardous Air Pollutants (Clean Air Act, Section 112(b)) A82W351
LB/Gal
kg/L
Volatile HAPS

0.00 0.000
Of solids

0.00 Ib/Ib

0.00 kg/kg
Air Quality Data
Density of Organic Solvent Blend

8.37 lb/gal
Photochemically Reactive
No
Waste Disposal
Waste from this product is not hazardous as defined under the Resource Conservation and Recovery Act (RCRA) 40 CFR 261.

Page 1942 of 2226 ends

page 3 of 3

ENVIRONMENTAL DATA SHEET
(Certified Product Data Sheet)
13 00 [0386]

PRODUCT NUMBER
B66W1310

PRODUCT NAME
PRO INDUSTRIALTM PRO-CRYL® Universal Acrylic Primer, Off White

MANUFACTURER'S NAME

THE SHERWIN-WILLIAMS COMPANY
1 Sherwin Way
Cleveland, OH 44113
Date of Preparation
Apr 18, 2026
This document includes all data required by 40 CFR 63.801(a) for a Certified Product Data Sheet under criteria specified in 40 CFR 63.805(a).

Hazard Category (for SARA 311.312)
B66W1310 = I Acute I Chronic
Product Weight

10.09 lb/gal
Volatile Ingredients
Chemical / Compound
SARA 302 EHS
CERCLA
HAPS 112
% by Weight
% by Volume
Water
7732-18-5
N
N
N
49 59
Specific Gravity

1.21 FLASH POINT
N.A.

Volatile Organic Compounds - U.S. EPA / Canada
B66W1310
LB/Gal
g/L
Coating Density

10.09 1209
By wt
By vol
Total Volatiles

50.4%

61.5%
Federally exempt solvents
Water

48.9%

59.3%
Non -Organic Volatiles
Ammonium Hydroxide

0.2%

0.2%
Organic Volatiles

1.3%

1.8%
Percent Non -Volatile

49.6%

38.5%
VOC Content
LB/Gal
g/L
Total

0.13 15
Less exempt solvents

0.32 39
Of solids

0.34 41
Of solids

0.02 Ib/Ib

0.02 kg/kg
By wt
By wt LVP-VOC

0.3%
Maximum Incremental Reactivity (MIR) (per US EPA Aerosol Ctg Rule, MIR Values 2009) 0.02

Page 1943 of 2226 ends

page 1 of 3

B66W1310
Volatile Organic Compounds - California
B66W1310
LB/Gal
g/L
Coating Density

10.09 1209
By wt
By vol
Total Volatiles

50.4%

61.5%
Exempt solvents
Water

48.9%

59.3%
Non -Organic Volatiles
Ammonium Hydroxide

0.2%

0.2%
Organic Volatiles

1.4%

1.9%
Percent Non -Volatile

49.6%

38.5%
VOC Content
LB/Gal
g/L
Total

0.14 17
Less exempt solvents

0.34 41
Of solids

0.36 44
Of solids

0.02 Ib/Ib

0.02 kg/kg
By wt
By wt LVP-VOC

0.4%
Maximum Incremental Reactivity (MIR) (per California Air Resources Board Aerosol Products Regulation, MIR Values 2010) 0.02 Volatile Organic Compounds - South Coast Air Quality Management District, California, US B66W1310
LB/Gal
g/L
Coating Density

10.09 1209
By wt
By vol
Total Volatiles

50.4%

61.5%
Exempt solvents
Water

48.9%

59.3%
Non -Organic Volatiles
Ammonium Hydroxide

0.2%

0.2%
Organic Volatiles

1.4%

1.9%
Percent Non -Volatile

49.6%

38.5%
VOC Content
LB/Gal
g/L
Total

0.14 17
Less exempt solvents

0.34 41
Of solids

0.36 44
Of solids

0.02 Ib/Ib

0.02 kg/kg
Volatile Organic Compounds - EU Directive 2004/42/EC
B66W1310
By wt
By vol
Total Volatiles

50.4%

61.4%
VOC Content
LB/Gal
g/L
Total

0.13 16

Page 1944 of 2226 ends

page 2 of 3

B66W1310
Volatile Organic Compounds - EU Directive 2010/75/EU
B66W1310
By wt
By vol
Total Volatiles

49.4%

60.2%
VOC Content
LB/Gal
g/L
Total

0.03 4
Volatile Organic Compounds - Mexico
B66W1310
LB/Gal
g/L
Coating Density

10.09 1209
By wt
By vol
Total Volatiles

50.4%

61.5%
Exempt solvents
Water

48.9%

59.3%
Non -Organic Volatiles
Ammonium Hydroxide

0.2%

0.2%
Organic Volatiles

1.4%

1.9%
Percent Non -Volatile

49.6%

38.5%
VOC Content
LB/Gal
g/L
Total

0.14 17
Less exempt solvents

0.34 41
Of solids

0.36 44
Of solids

0.02 Ib/Ib

0.02 kg/kg
Hazardous Air Pollutants (Clean Air Act, Section 112(b)) B66W1310
LB/Gal
kg/L
Volatile HAPS

0.00 0.000
Of solids

0.00 Ib/Ib

0.00 kg/kg
Air Quality Data
Density of Organic Solvent Blend

7.22 lb/gal
Photochemically Reactive
No
Waste Disposal
Waste from this product is not hazardous as defined under the Resource Conservation and Recovery Act (RCRA) 40 CFR 261.

Page 1945 of 2226 ends

page 3 of 3

ENVIRONMENTAL DATA SHEET
(Certified Product Data Sheet)
35 00 [3205]

PRODUCT NUMBER
B66W1151

PRODUCT NAME
PRO INDUSTRIALTM DTM Acrylic Semi -Gloss, Extra White

MANUFACTURER'S NAME

Hazard Category (for SARA 311.312)
B66W1151 = I Chronic
Product Weight

10.20 lb/gal
Volatile Ingredients
Chemical / Compound
SARA 302 EHS
CERCLA
HAPS 112
% by Weight
% by Volume
Trimethylpentanediol Isobutyrate
25265-77-4
N
N
N
1 2
Water
7732-18-5
N
N
N
48 60
Specific Gravity

1.23 FLASH POINT
N.A.

Volatile Organic Compounds - U.S. EPA / Canada
B66W1151
LB/Gal
g/L
Coating Density

10.20 1222
By wt
By vol
Total Volatiles

49.1%

62.1%
Federally exempt solvents
Water

47.8%

60.3%
Organic Volatiles

1.2%

1.6%
Percent Non -Volatile

50.9%

37.9%
VOC Content
LB/Gal
g/L
Total

0.12 14
Less exempt solvents

0.31 37
Of solids

0.32 39
Of solids

0.02 Ib/Ib

0.02 kg/kg
By wt
By wt LVP-VOC

0.0%
Maximum Incremental Reactivity (MIR) (per US EPA Aerosol Ctg Rule, MIR Values 2009) 0.01

Page 1946 of 2226 ends

page 1 of 3

B66W1151
Volatile Organic Compounds - California
B66W1151
LB/Gal
g/L
Coating Density

10.20 1222
By wt
By vol
Total Volatiles

49.1%

62.1%
Exempt solvents
Water

47.8%

60.3%
Organic Volatiles

1.2%

1.6%
Percent Non -Volatile

50.9%

37.9%
VOC Content
LB/Gal
g/L
Total

0.12 14
Less exempt solvents

0.31 37
Of solids

0.32 39
Of solids

0.02 Ib/Ib

0.02 kg/kg
By wt
By wt LVP-VOC

0.0%
Maximum Incremental Reactivity (MIR) (per
California Air Resources Board Aerosol Products Regulation, MIR Values 2010) 0.01 Volatile Organic Compounds
- South Coast Air Quality Management District, California, US B66W1151
LB/Gal
g/L
Coating Density

10.20 1222
By wt
By vol
Total Volatiles

49.1%

62.1%
Exempt solvents
Water

47.8%

60.3%
Organic Volatiles

1.2%

1.6%
Percent Non -Volatile

50.9%

37.9%
VOC Content
LB/Gal
g/L
Total

0.12 14
Less exempt solvents

0.31 37
Of solids

0.32 39
Of solids

0.02 Ib/Ib

0.02 kg/kg
Volatile Organic Compounds - EU Directive 2004/42/EC
B66W1151
By wt
By vol
Total Volatiles

47.9%

60.6%
VOC Content
LB/Gal
g/L
Total

0.00 0
Volatile Organic Compounds - EU Directive 2010/75/EU
B66W1151
By wt
By vol
Total Volatiles

47.9%

60.5%
VOC Content
LB/Gal
g/L
Total

0.00 0

Page 1947 of 2226 ends

page 2 of 3

B66W1151
Volatile Organic Compounds - Mexico
B66W1151
LB/Gal
g/L
Coating Density

10.20 1222
By wt
By vol
Total Volatiles

49.1%

62.1%
Exempt solvents
Water

47.8%

60.3%
Organic Volatiles

1.2%

1.6%
Percent Non -Volatile

50.9%

37.9%
VOC Content
LB/Gal
g/L
Total

0.12 14
Less exempt solvents

0.31 37
Of solids

0.32 39
Of solids

0.02 Ib/Ib

0.02 kg/kg
Hazardous Air Pollutants (Clean Air Act, Section 112(b)) B66W1151
LB/Gal
kg/L
Volatile HAPS

0.00 0.000
Of solids

0.00 Ib/Ib

0.00 kg/kg
Air Quality Data
Density of Organic Solvent Blend

7.75 lb/gal
Photochemically Reactive
No
Waste Disposal
Waste from this product is not hazardous as defined under the Resource Conservation and Recovery Act (RCRA) 40 CFR 261.

Page 1948 of 2226 ends

page 3 of 3

ENVIRONMENTAL DATA SHEET
(Certified Product Data Sheet)
1100 [3645]

PRODUCT NUMBER
B53W5151

PRODUCT NAME
PRO INDUSTRIALTM Waterbased Alkyd Urethane Semi -Gloss, Extra White

MANUFACTURER'S NAME

Hazard Category (for SARA 311.312)
B53W5151 = I Chronic
Product Weight

10.69 lb/gal
Volatile Ingredients
Chemical / Compound
SARA 302 EHS
CERCLA
HAPS 112
% by Weight
% by Volume
Water
7732-18-5
N
N
N
50 66
Specific Gravity

1.29 FLASH POINT
N.A.

Volatile Organic Compounds - U.S. EPA / Canada
B53W5151
LB/Gal
g/L
Coating Density

10.69 1281
By wt
By vol
Total Volatiles

51.3%

67.2%
Federally exempt solvents
Water

50.3%

65.8%
2 -Amino -2 -Methyl -1-
Propanol

0.1%

0.2%
Organic Volatiles

0.8%

1.2%
Percent Non -Volatile

48.7%

32.8%
VOC Content
LB/Gal
g/L
Total

0.08 9
Less exempt solvents

0.23 28
Of solids

0.24 29
Of solids

0.01 Ib/Ib

0.01 kg/kg
By wt
By wt LVP-VOC

0.4%
Maximum Incremental Reactivity (MIR) (per US EPA Aerosol Ctg Rule, MIR Values 2009) 0.09

Page 1949 of 2226 ends

page 1 of 3

B53W5151
Volatile Organic Compounds - California
B53W5151
LB/Gal
g/L
Coating Density

10.69 1281
By wt
By vol
Total Volatiles

51.3%

67.2%
Exempt solvents
Water

50.3%

65.8%
Organic Volatiles

0.9%

1.4%
Percent Non -Volatile

48.7%

32.8%
VOC Content
LB/Gal
g/L
Total

0.09 11
Less exempt solvents

0.27 33
Of solids

0.28 34
Of solids

0.01 Ib/Ib

0.01 kg/kg
By wt
By wt LVP-VOC

0.5%
Maximum Incremental Reactivity (MIR) (per
California Air Resources Board Aerosol Products Regulation, MIR Values 2010) 0.02 Volatile Organic Compounds
- South Coast Air Quality Management District, California, US B53W5151
LB/Gal
g/L
Coating Density

10.69 1281
By wt
By vol
Total Volatiles

51.3%

67.2%
Exempt solvents
Water

50.3%

65.8%
Organic Volatiles

0.9%

1.4%
Percent Non -Volatile

48.7%

32.8%
VOC Content
LB/Gal
g/L
Total

0.09 11
Less exempt solvents

0.27 33
Of solids

0.28 34
Of solids

0.01 Ib/Ib

0.01 kg/kg
Volatile Organic Compounds - EU Directive 2004/42/EC
B53W5151
By wt
By vol
Total Volatiles

51.4%

67.3%
VOC Content
LB/Gal
g/L
Total

0.11 13
Volatile Organic Compounds - EU Directive 2010/75/EU
B53W5151
By wt
By vol
Total Volatiles

51.3%

67.2%
VOC Content
LB/Gal
g/L
Total

0.09 11

Page 1950 of 2226 ends

page 2 of 3

B53W5151
Volatile Organic Compounds - Mexico
B53W5151
LB/Gal
g/L
Coating Density

10.69 1281
By wt
By vol
Total Volatiles

51.3%

67.2%
Exempt solvents
Water

50.3%

65.8%
Organic Volatiles

0.9%

1.4%
Percent Non -Volatile

48.7%

32.8%
VOC Content
LB/Gal
g/L
Total

0.09 11
Less exempt solvents

0.27 33
Of solids

0.28 34
Of solids

0.01 Ib/Ib

0.01 kg/kg
Hazardous Air Pollutants (Clean Air Act, Section 112(b)) B53W5151
LB/Gal
kg/L
Volatile HAPS

0.00 0.000
Of solids

0.00 Ib/Ib

0.00 kg/kg
Air Quality Data
Density of Organic Solvent Blend

6.97 lb/gal
Photochemically Reactive
No
Waste Disposal
Waste from this product is not hazardous as defined under the Resource Conservation and Recovery Act (RCRA) 40 CFR 261.

Page 1951 of 2226 ends

page 3 of 3

Safety Data Sheets

Page 1952 of 2226 ends

SAFETY DATA SHEET
According to 29 CFR 1910.1200
B51 W620
Section 1. Identification
Product name
Product code
Other means of
identification
: ProBlock® Premium All -Purpose Water -Based Interior/Exterior Primer White
: B51 W620
: Not available.

Product type : Liquid.

Relevant identified uses of the substance or mixture and uses advised against Paint or paint related material.

Manufacturer
Emergency telephone
number of the company
Product Information
Telephone Number
Transportation Emergency
Telephone Number
: THE SHERWIN-WILLIAMS COMPANY
101 W. Prospect Avenue
Cleveland, OH 44115
: US / Canada: (800) 424-9300
Mexico: SETIQ 800-00-214-00 / 55-5559-1588 Available 24 hours and 365 days a year : US / Canada: 1-800-474-3794
Mexico: Not Available
US / Canada: (800) 424-9300
Mexico: SETIQ 800-00-214-00 / 55-5559-1588 Available 24 hours and 365 days a year Section 2. Hazards identification
OSHAIHCS status
Classification of the
substance or mixture
GHS label elements
Hazard pictograms
Signal word
Hazard statements
Precautionary statements
General
Prevention
Response
Storage
: This material is considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200).
: CARCINOGENICITY - Category 1B
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) - Category 1 : Danger
: May cause cancer.

Causes damage to organs through prolonged or repeated exposure. (lungs) Keep out of reach of children. If medical advice is needed, have product container or label at hand.

Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Wear protective gloves, protective clothing and eye or face protection. Do not breathe vapor. Do not eat, drink or smoke when using this product.

Wash thoroughly after handling.

IF exposed or concerned: Get medical advice or attention.

Store locked up. Page 1953 of 2226
Date of issue/Date of revision : 5/2/2026 Date of previous issue : 11/4/2025 Version : 24.02 1/13

Section 2. Hazards identification
Disposal
Supplemental label
elements
Hazards not otherwise
classified
Hazards identified when
used
: Dispose of contents and container in accordance with all local, regional, national and international regulations.

WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

This product contains a TSCA regulated chemical. See Section 15 of the US SDS for details.

Please refer to the SDS for additional information. Keep out of reach of children. Do not transfer contents to other containers for storage.
: None known.
: No known significant effects or critical hazards.

Section 3. Composition/information on ingredients
Substance/mixture : Mixture
Other means of : Not available.
identification
CAS number/other identifiers
Ingredient name
% by weight
Identifiers
Titanium Dioxide
≥10 - ≤25
13463-67-7
Talc
≤10
14807-96-6
Attapulgite Clay
≤1
12174-11-7
Any concentration shown as a range is to protect confidentiality or is due to batch variation.

There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are classified and hence require reporting in this section.

Occupational exposure limits, if available, are listed in Section 8.

Section 4. First aid measures
Description of necessary first aid measures
Eye contact
Inhalation
Skin contact
Ingestion
: Immediately flush eyes with plenty of water, occasionally lifting the upper and lower eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10 minutes. Get medical attention.
: Remove victim to fresh air and keep at rest in a position comfortable for breathing. If not breathing, if breathing is irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. Get medical attention. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway.

Loosen tight clothing such as a collar, tie, belt or waistband. In case of inhalation of decomposition products in a fire, symptoms may be delayed. The exposed person may need to be kept under medical surveillance for 48 hours. : Flush contaminated skin with plenty of water. Remove contaminated clothing and shoes. Wash contaminated clothing thoroughly with water before removing it, or wear gloves. Continue to rinse for at least 10 minutes. Get medical attention. Wash clothing before reuse. Clean shoes thoroughly before reuse.
: Wash out mouth with water. Remove dentures if any. If material has been swallowed and the exposed person is conscious, give small quantities of water to drink. Stop if the exposed person feels sick as vomiting may be dangerous. Do not induce vomiting unless directed to do so by medical personnel. If vomiting occurs, the head should be kept low so that vomit does not enter the lungs. Get medical attention. Never give anything by mouth to an unconscious person. If unconscious, place in recovery position and get medical fitagktori 964€0114a26Maintain an open airway. Loosen tight clothing Date of issue/Date of revision : 5/2/2026 Date of previous issue : 11/4/2025 Version :24.02 2/13

Section 4. First aid measures
such as a collar, tie, belt or waistband.

Most important symptoms/effects, acute and delayed
Potential acute health effects
Eye contact
Inhalation
Skin contact
Ingestion
: No known significant effects
: No known significant effects
: No known significant effects
: No known significant effects
Over -exposure signs/symptoms
Eye contact
Inhalation
Skin contact
Ingestion
No specific data.

No specific data.

No specific data.
or critical hazards.
or critical hazards.
or critical hazards.
or critical hazards.

Indication of immediate medical attention and special treatment needed, if necessary Notes to physician
Specific treatments
Protection of first-aiders
: In case of inhalation of decomposition products in a fire, symptoms may be delayed.

The exposed person may need to be kept under medical surveillance for 48 hours.

No specific treatment.

No action shall be taken involving any personal risk or without suitable training. If it is suspected that fumes are still present, the rescuer should wear an appropriate mask or self-contained breathing apparatus. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. Wash contaminated clothing thoroughly with water before removing it, or wear gloves.

See toxicological information (Section 11)
Section 5. Fire -fighting measures
Extinguishing media
Suitable extinguishing
media
Unsuitable extinguishing
media
Specific hazards arising
from the chemical
Hazardous thermal
decomposition products
: Use an extinguishing agent suitable for the surrounding fire. : None known.
: In a fire or if heated, a pressure increase will occur and the container may burst. : Decomposition products may include the following materials:
carbon dioxide
carbon monoxide
nitrogen oxides
metal oxide/oxides
Special protective actions .
for fire-fighters
Special protective
equipment for fire-fighters
Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a fire. No action shall be taken involving any personal risk or without suitable training.

Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face -piece operated in positive pressure mode.

Page 1955 of 2226 ends

Date of issue/Date of revision : 5/2/2026 Date of previous issue : 11/4/2025 Version :24.02 3/13

Section 6. Accidental release measures
Personal precautions, protective equipment and emergency procedures For non -emergency
personnel
: No action shall be taken involving any personal risk or without suitable training.

Evacuate surrounding areas. Keep unnecessary and unprotected personnel from entering. Do not touch or walk through spilled material. Avoid breathing vapor or mist.

Provide adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment.

For emergency responders : If specialized clothing is required to deal with the spillage, take note of any information in Section 8 on suitable and unsuitable materials. See also the information in "For non - emergency personnel".

Environmental precautions
: This product contains a TSCA regulated chemical. See Section 15 of the US SDS for details.

Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities if the product has caused environmental pollution (sewers, waterways, soil or air).

Methods and materials for containment and cleaning up
Small spill
Large spill
: Stop leak if without risk. Move containers from spill area. Absorb with an inert material and place in an appropriate waste disposal container. Dispose of via a licensed waste disposal contractor.
: Stop leak if without risk. Move containers from spill area. Approach release from upwind. Prevent entry into sewers, water courses, basements or confined areas. Wash spillages into an effluent treatment plant or proceed as follows. Dispose of via a licensed waste disposal contractor. Contaminated absorbent material may pose the same hazard as the spilled product. Contain and collect spillage with non-combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in container for disposal according to local regulations.

Section 7. Handling and storage
Precautions for safe handling
Protective measures
Advice on general
occupational hygiene
: Put on appropriate personal protective equipment (see Section 8). Avoid exposure - obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Do not get in eyes or on skin or clothing. Do not breathe vapor or mist. Do not ingest. If during normal use the material presents a respiratory hazard, use only with adequate ventilation or wear appropriate respirator. Keep in the original container or an approved alternative made from a compatible material, kept tightly closed when not in use. Empty containers retain product residue and can be hazardous. Do not reuse container.
: Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment before entering eating areas. See also Section 8 for additional information on hygiene measures.

Conditions for safe storage, : Store in accordance with local regulations. Store in original container protected from including any direct sunlight in a dry, cool and well -ventilated area, away from incompatible materials incompatibilities (see Section 10) and food and drink. Store locked up. Keep container tightly closed and sealed until ready for use. Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabeled containers.

Use appropriate containment to avoid environmental contamination. See Section 10 for incompatible materials before handling or use.

Page 1956 of 2226 ends

Date of issue/Date of revision : 5/2/2026 Date of previous issue : 11/4/2025 Version :24.02 4/13

Section 8. Exposure controls/personal protection
Control parameters
Occupational exposure limits(OSHA United States)
Ingredient name
CAS #
Exposure limits
Titanium Dioxide
13463-67-7
ACGIH TLV (United States, 1/2025) A3.

TWA 8 hours: 2.5 mg/m3. Form: respirable
fraction, finescale particles.

NIOSH REL (United States, 10/2020) NIA.

OSHA PEL (United States, 5/2018)
TWA 8 hours: 15 mg/m3. Form: Total dust.

Talc
14807-96-6
ACGIH TLV (United States, 1/2025) A4.

TWA 8 hours: 2 mg/m3. Form: Respirable
fraction.

NIOSH REL (United States, 10/2020)
TWA 10 hours: 2 mg/m3. Form: Respirable
fraction.

Attapulgite Clay
12174-11-7
None.

Occupational exposure limits (Canada)
Ingredient name
CAS #
Exposure limits
talc (none asbestiform)
14807-96-6
CA Saskatchewan Provincial (Canada, N
4/2021)
TWA 8 hours: 2 mg/m3. Form: respirable
fraction.

CA British Columbia Provincial (Canada,
6/2025)
TWA 8 hours: 2 mg/m3. Form: respirable.

Notes: the value is for particulate matter
containing no asbestos and less than 1%
crystalline silica.

CA Ontario Provincial (Canada, 6/2019)
TWA 8 hours: 2 mg/m3. Form: respirable
particulate matter.

TWA 8 hours: 2 fibers/cm3.

CA Quebec Provincial (Canada, 2/2024)
TWAEV 8 hours: 2 mg/m3. Form: respirable
aerosol fraction.

CA Alberta Provincial (Canada, 3/2023)
OEL 8 hours: 2 mg/m3. Form: respirable
particulate.

Fibres -Natural Mineral Fibres, Attapulgite
12174-11-7
CA Quebec Provincial (Canada, 2/2024)
[Attapulgite] C1.

TWAEV 8 hours: 1 fibers/cm3. Form:

RESPIRABLE FIBRES (other than respirable
asbestos fibres) : Objects, other than
respirable asbestos fibres, longer than 5 pm,
having a diameter of less than 3 µm and a
ratio of length to diameter of more than 3 : 1..

Occupational exposure limits (Mexico)
None.

Biological exposure indices (United States)
No exposure indices known.

Biological exposure indices (Canada) Page 1957 of 2226
Date of issue/Date of revision : 5/2/2026 Date of previous issue : 11/4/2025 Version :24.02 5/13

Section 8. Exposure controls/personal protection
No exposure indices known.

Biological exposure indices (Mexico)
No exposure indices known.

Appropriate engineering
controls
Environmental exposure
controls
Individual protection measures
Hygiene measures
Eye/face protection
Skin protection
Hand protection
Body protection
Other skin protection
Respiratory protection
If user operations generate dust, fumes, gas, vapor or mist, use process enclosures, local exhaust ventilation or other engineering controls to keep worker exposure to airborne contaminants below any recommended or statutory limits.

This product contains a TSCA regulated chemical. See Section 15 of the US SDS for details.

Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at the end of the working period.

Appropriate techniques should be used to remove potentially contaminated clothing.

Wash contaminated clothing before reusing. Ensure that eyewash stations and safety showers are close to the workstation location.
: Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid exposure to liquid splashes, mists, gases or dusts. If contact is possible, the following protection should be worn, unless the assessment indicates a higher degree of protection: safety glasses with side - shields.
: Chemical -resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical products if a risk assessment indicates this is necessary. Considering the parameters specified by the glove manufacturer, check during use that the gloves are still retaining their protective properties. It should be noted that the time to breakthrough for any glove material may be different for different glove manufacturers. In the case of mixtures, consisting of several substances, the protection time of the gloves cannot be accurately estimated. : Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product.
: Appropriate footwear and any additional skin protection measures should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product.
: Based on the hazard and potential for exposure, select a respirator that meets the appropriate standard or certification. Respirators must be used according to a respiratory protection program to ensure proper fitting, training, and other important aspects of use.

Section 9. Physical and chemical properties
The conditions of measurement of all properties are at standard temperature and pressure unless otherwise indicated.

Appearance
Physical state
Color
Odor
Odor threshold
pH
Liquid.

White.

Not available.

8.8

Page 1958 of 2226 ends

Date of issue/Date of revision : 5/2/2026 Date of previous issue : 11/4/2025 Version :24.02 6/13

Section 9. Physical and chemical properties
Melting point/freezing point
Boiling point or initial
boiling point and boiling
range
Flash point
Evaporation rate
Flammability
Lower and upper explosion
limit/flammability limit
Vapor pressure
Relative vapor density
Relative density
Density
Solubility(ies)
: Not available.
: 100°C (212°F)
: Closed cup: Not applicable.
: 0.09 (butyl acetate = 1)
: Not available.
: Not available.
: 2.3 kPa (17.5 mm Hg)
: 1 [Air= 1]
: 1.31
: 1.3 g/cm3
Media
Result
cold water
Partially soluble
Partition coefficient: n-
octanol/water
Auto -ignition temperature
Decomposition temperature
Viscosity
Molecular weight
Particle characteristics
Median particle size
Heat of combustion
: Not applicable.
: Not available.
: Not available.
: Dynamic (room temperature): Not available.

Kinematic (room temperature): Not available.

Kinematic (40°C (104°F)): >20.5 mm2/s (>20.5 cSt)
: Not applicable.
: Not applicable.
: 0.165 kJ/g
Section 10. Stability and reactivity
Reactivity
Chemical stability
Possibility of hazardous
reactions
Conditions to avoid
Incompatible materials
Hazardous decomposition
products
: No specific test data related to reactivity available for this product or its ingredients. : The product is stable.
: Under normal conditions of storage and use, hazardous reactions will not occur. : No specific data.
: No specific data.
: Under normal conditions of storage and use, hazardous decomposition products should not be produced.

Page 1959 of 2226 ends

Date of issue/Date of revision : 5/2/2026 Date of previous issue : 11/4/2025 Version :24.02 7/13

Section 11. Toxicological information
Information on toxicological effects
Acute toxicity
Not available.

Conclusion/Summary [Product] : Not available.

Skin corrosion/irritation
Product/ingredient name
Titanium Dioxide
Talc
Conclusion/Summary [Product]
Serious eye damage/eye irritation
Not available.

Conclusion/Summary [Product]
Respiratory corrosion/irritation
Not available.

Conclusion/Summary [Product]
Respiratory or skin sensitization
Not available.

Skin
Conclusion/Summary [Product]
Respiratory
Conclusion/Summary [Product]
Germ cell mutagenicity
Not available.

Conclusion/Summary [Product]
Carcinogenicity
Not available.

Result
Human - Skin - Mild irritant
Duration of treatment/exposure: 72 hours
Amount/concentration applied: 300 ug I
Human - Skin - Mild irritant
Duration of treatment/exposure: 72 hours
Amount/concentration applied: 300 ug I
: Not available.
: Not available.
: Not available.
: Not available.
: Not available.
: Not available.

Conclusion/Summary [Product]
: Not available.

Page 1960 of 2226 ends

Date of issue/Date of revision : 5/2/2026 Date of previous issue : 11/4/2025 Version :24.02 8/13

Section 11. Toxicological information
Classification
Product/ingredient name
OSHA
IARC
NTP
Titanium Dioxide
Talc
Attapulgite Clay
-
-
-
2B
2A
2B
-
-
-
Reproductive toxicity
Not available.

Conclusion/Summary [Product] : Not available.

Specific target organ toxicity (single exposure)
Not available.

Specific target organ toxicity (repeated exposure)
Product/ingredient name
Talc
Aspiration hazard
Not available.

Information on the likely routes of exposure
Not available.

Potential acute health effects
Eye contact
Inhalation
Skin contact
Ingestion
Result

SPECIFIC TARGET ORGAN TOXICITY (REPEATED
EXPOSURE) (lungs) (inhalation) - Category 1
: No known significant effects or critical hazards.
: No known significant effects or critical hazards.
: No known significant effects or critical hazards.
: No known significant effects or critical hazards.

Symptoms reiatea to the pnysicai, cnemicai ana toxicological cnaracteristics Eye contact
Inhalation
Skin contact
Ingestion
: No specific data.
: No specific data.
: No specific data.
: No specific data.

Delayed and immediate effects and also chronic effects from short and long term exposure Short term exposure
Potential immediate : Not available.
effects
Potential delayed effects : Not available.

Long term exposure
Potential immediate : Not available.
effects
Potential delayed effects : Not available. Page 1961 of 2226 Date of issue/Date of revision : 5/2/2026 Date of previous issue : 11/4/2025 Version : 24.02 9/13

Section 11. Toxicological information
Potential chronic health effects
Not available.

Conclusion/Summary [Product] : Not available.

General
Carcinogenicity
Mutagenicity
Reproductive toxicity
: Causes damage to organs through prolonged or repeated exposure. : May cause cancer. Risk of cancer depends on duration and level of exposure. : No known significant effects or critical hazards.
: No known significant effects or critical hazards.

Numerical measures of toxicity
Acute toxicity estimates
N/A
Section 12. Ecological information
Toxicity
Product/ingredient name
Titanium Dioxide
Result
Acute - LC50 - Marine water
Fish - Mummichog - Fundulus heteroclitus
>1000 mg/I [96 hours]
Effect: Mortality
Conclusion/Summary [Product] : Not available.

Persistence and degradability
Not available.

Conclusion/Summary [Product] : Not available.

Bioaccumulative potential
Not available.

Mobility in soil
Soil/Water partition
coefficient
: Not available.

Other adverse effects
No known significant effects or critical hazards.

Page 1962 of 2226 ends

Date of issue/Date of revision : 5/2/2026 Date of previous issue : 11/4/2025 Version :24.02 10/13

Section 13. Disposal considerations
Disposal methods
: This product contains a TSCA regulated chemical. See Section 15 of the US SDS for details.

The generation of waste should be avoided or minimized wherever possible. Disposal of this product, solutions and any by-products should at all times comply with the requirements of environmental protection and waste disposal legislation and any regional local authority requirements. Dispose of surplus and non -recyclable products via a licensed waste disposal contractor. Waste should not be disposed of untreated to the sewer unless fully compliant with the requirements of all authorities with jurisdiction.

Waste packaging should be recycled. Incineration or landfill should only be considered when recycling is not feasible. This material and its container must be disposed of in a safe way. Care should be taken when handling emptied containers that have not been cleaned or rinsed out. Empty containers or liners may retain some product residues.

Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers.

Section 14. Transport information
DOT
Classification
TDG
Classification
Mexico
Classification
IATA
IMDG
UN number
Not regulated.

Not regulated.

UN proper
shipping name
-
-
-
-
-
Transport
hazard class(es)
-
-
-
-
-
Packing group
-
-
-
-
-
Environmental
hazards
No.

No.

Additional
information
-
-
-
-
-
Special precautions for user :

Multi -modal shipping descriptions are provided for informational purposes and do not consider container sizes. The presence of a shipping description for a particular mode of transport (sea, air, etc.), does not indicate that the product is packaged suitably for that mode of transport. All packaging must be reviewed for suitability prior to shipment, and compliance with the applicable regulations is the sole responsibility of the person offering the product for transport. People loading and unloading dangerous goods must be trained on all of the risks deriving from the substances and on all actions in case of emergency situations.

Transport in bulk according : Not available.
to IMO instruments
Proper shipping name : Not available.

Page 1963 of 2226 ends

Date of issue/Date of revision : 5/2/2026 Date of previous issue : 11/4/2025 Version :24.02 11/13

Section 15. Regulatory information
U.S. Federal regulations
: TSCA 5(a)2 final significant new use rules: Sodium Nitrite List name Name on list Notes
TSCA 5(a)2 - Sodium Nitrite 40 CFR 721.4740
Final significant (Nitrites of
new use rules Alkali Metals
(Group IA
elements))
California Prop. 65
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

International regulations
Montreal Protocol
Not listed.

Stockholm Convention on Persistent Organic Pollutants
Not listed.

International lists
: Australia inventory (AIIC): Not determined.

China inventory (IECSC): Not determined.

Japan inventory (CSCL): Not determined.

Japan inventory (ISHL): Not determined.

Korea inventory (KECI): Not determined.

New Zealand Inventory of Chemicals (NZIoC): Not determined.

Philippines inventory (PICCS): Not determined.

Taiwan Chemical Substances Inventory (TCSI): Not determined.

Thailand inventory: Not determined.

Turkey inventory: Not determined.

Vietnam inventory: Not determined.

Section 16. Other information
Hazardous Material Information System (U.S.A.)
Flammability
3 0
0 The customer is responsible for determining the PPE code for this material. For more information on HMIS® Personal Protective Equipment (PPE) codes, consult the HMIS® Implementation Manual.

Caution: HMIS® ratings are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4 representing significant hazards or risks. Although HMIS® ratings and the associated label are not required on SDSs or products leaving a facility under 29 CFR 1910.1200, the preparer may choose to provide them. HMIS® ratings are to be used with a fully implemented HMIS® program. HMIS® is a registered trademark and service mark of the American Coatings Association, Inc.

Procedure used to derive the classification
Classification
Justification
CARCINOGENICITY - Category 1B
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) - Category 1 Calculation method
Calculation method
History
Date of printing
: 5/2/2026
Date of issue/Date of : 5/2/2026
revision

Page 1964 of 2226 ends

Date of issue/Date of revision : 5/2/2026 Date of previous issue : 11/4/2025 Version :24.02 12/13

Section 16. Other information
Date of previous issue
Version
Key to abbreviations
11/4/2025
: 24.02
: ATE = Acute Toxicity Estimate
BCF = Bioconcentration Factor
GHS = Globally Harmonized System of Classification and Labelling of Chemicals IATA = International Air Transport Association
IBC = Intermediate Bulk Container
IMDG = International Maritime Dangerous Goods
LogPow = logarithm of the octanol/water partition coefficient MARPOL = International Convention for the Prevention of Pollution From Ships, 1973 as modified by the Protocol of 1978. ("Marpol" = marine pollution) N/A = Not available
SGG = Segregation Group
UN = United Nations
V Indicates information that has changed from previously issued version.

Notice to reader
It is recommended that each customer or recipient of this Safety Data Sheet (SDS) study it carefully and consult resources, as necessary or appropriate, to become aware of and understand the data contained in this SDS and any hazards associated with the product. This information is provided in good faith and believed to be accurate as of the effective date herein. However, no warranty, express or implied, is given. The information presented here applies only to the product as shipped. The addition of any material can change the composition, hazards and risks of the product. Products shall not be repackaged, modified, or tinted except as specifically instructed by the manufacturer, including but not limited to the incorporation of products not specified by the manufacturer, or the use or addition of products in proportions not specified by the manufacturer. Regulatory requirements are subject to change and may differ between various locations and jurisdictions. The customer/buyer/user is responsible to ensure that his activities comply with all country, federal, state, provincial or local laws. The conditions for use of the product are not under the control of the manufacturer; the customer/buyer/user is responsible to determine the conditions necessary for the safe use of this product. The customer/buyer/user should not use the product for any purpose other than the purpose shown in the applicable section of this SDS without first referring to the supplier and obtaining written handling instructions. Due to the proliferation of sources for information such as manufacturer -specific SDS, the manufacturer cannot be responsible for SDSs obtained from any other source.

Page 1965 of 2226 ends

Date of issue/Date of revision : 5/2/2026 Date of previous issue : 11/4/2025 Version : 24.02 13/13

SAFETY DATA SHEET
According to 29 CFR 1910.1200
A82W351
Section 1. Identification
Product name
Product code
Other means of
identification
: A-100® Exterior Satin Latex Paint
Extra White
: A82W351
: Not available.

Product type : Liquid.

Relevant identified uses of the substance or mixture and uses advised against Paint or paint related material.

Manufacturer
Emergency telephone
number of the company
Product Information
Telephone Number
Transportation Emergency
Telephone Number
: THE SHERWIN-WILLIAMS COMPANY
101 W. Prospect Avenue
Cleveland, OH 44115
: US / Canada: (800) 424-9300
Mexico: SETIQ 800-00-214-00 / 55-5559-1588 Available 24 hours and 365 days a year : US / Canada: 1-800-474-3794
Mexico: Not Available
US / Canada: (800) 424-9300
Mexico: SETIQ 800-00-214-00 / 55-5559-1588 Available 24 hours and 365 days a year Section 2. Hazards identification
OSHAIHCS status
Classification of the
substance or mixture
GHS label elements
Hazard pictograms
Signal word
Hazard statements
Precautionary statements
General
Prevention
Response
Storage
Disposal
: This material is considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200).
: CARCINOGENICITY - Category 2
: Warning
: Suspected of causing cancer.

Keep out of reach of children. If medical advice is needed, have product container or label at hand.

Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Wear protective gloves, protective clothing and eye or face protection.

IF exposed or concerned: Get medical advice or attention.

Store locked up.

Dispose of conte s and,pRptainoerr5�cordance with all local, regional, national and a��s international reg . L
Date of issue/Date of revision : 5/2/2026 Date of previous issue : 3/4/2026 Version :7.01 1/14

Section 2. Hazards identification
Supplemental label
elements
Hazards not otherwise
classified
Hazards identified when
used
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

Section 3. Composition/information on ingredients
Substance/mixture
Other means of
identification
CAS number/other identifiers
: Mixture
: Not available.

Ingredient name
% by weight
Identifiers
Titanium Dioxide
≥10 - ≤25
13463-67-7
Zinc Oxide
≤3
1314-13-2
Attapulgite Clay
≤1
12174-11-7
Any concentration shown as a range is to protect confidentiality or is due to batch variation.

There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are classified and hence require reporting in this section.

Occupational exposure limits, if available, are listed in Section 8.

Loosen tight clothing such as a collar, tie, belt or waistband. : Flush contaminated skin with plenty of water. Remove contaminated clothing and shoes. Continue to rinse for at least 10 minutes. Get medical attention. Wash clothing before reuse. Clean shoes thoroughly before reuse.
: Wash out mouth with water. Remove dentures if any. If material has been swallowed and the exposed person is conscious, give small quantities of water to drink. Stop if the exposed person feels sick as vomiting may be dangerous. Do not induce vomiting unless directed to do so by medical personnel. If vomiting occurs, the head should be kept low so that vomit does not enter the lungs. Get medical attention. Never give anything by mouth to an unconscious person. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband.

Most important symptoms/effects, acute and delayed
Potential acute health effects
Eye contact : No known significant effects or critical hazards.

Inhalation : No known signific3P.$fdc ar@fit Pazards.

Date of issue/Date of revision : 5/2/2026 Date of previous issue : 3/4/2026 Version :7.01 2/14

Section 4. First aid measures
Skin contact
Ingestion
: No known significant effects or critical hazards.
: No known significant effects or critical hazards.

Over -exposure signs/symptoms
Eye contact
Inhalation
Skin contact
Ingestion
No specific data.

No specific data.

Indication of immediate medical attention and special treatment needed, if necessary Notes to physician
Specific treatments
Protection of first-aiders
Treat symptomatically. Contact poison treatment specialist immediately if large quantities have been ingested or inhaled.

No specific treatment.

No action shall be taken involving any personal risk or without suitable training. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation.

See toxicological information (Section 11)
Section 5. Fire -fighting measures
Extinguishing media
Suitable extinguishing
media
Unsuitable extinguishing
media
Specific hazards arising
from the chemical
Hazardous thermal
decomposition products
: Use an extinguishing agent suitable for the surrounding fire. : None known.
: In a fire or if heated, a pressure increase will occur and the container may burst. : Decomposition products may include the following materials:
carbon dioxide
carbon monoxide
metal oxide/oxides
Special protective actions .
for fire-fighters
Special protective
equipment for fire-fighters
Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a fire. No action shall be taken involving any personal risk or without suitable training.

Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face -piece operated in positive pressure mode.

Section 6. Accidental release measures
Personal precautions, protective equipment and emergency procedures For non -emergency
personnel
For emergency responders :

No action shall be taken involving any personal risk or without suitable training.

Evacuate surrounding areas. Keep unnecessary and unprotected personnel from entering. Do not touch or walk through spilled material. Avoid breathing vapor or mist.

Provide adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment.

If specialized clothing is required to deal with the spillage, take note of any information in Section 8 on suitable and unsuitable materials. See also the information in "For non - emergency personnel".

Environmental precautions

Page 1968 of 2226 ends

Date of issue/Date of revision : 5/2/2026 Date of previous issue : 3/4/2026 Version :7.01 3/14

Section 6. Accidental release measures
Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities if the product has caused environmental pollution (sewers, waterways, soil or air).

Section 7. Handling and storage
Precautions for safe handling
Protective measures
Advice on general
occupational hygiene
: Put on appropriate personal protective equipment (see Section 8). Avoid exposure - obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Do not get in eyes or on skin or clothing. Do not ingest.

Avoid breathing vapor or mist. If during normal use the material presents a respiratory hazard, use only with adequate ventilation or wear appropriate respirator. Keep in the original container or an approved alternative made from a compatible material, kept tightly closed when not in use. Empty containers retain product residue and can be hazardous. Do not reuse container.
: Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment before entering eating areas. See also Section 8 for additional information on hygiene measures.

Use appropriate containment to avoid environmental contamination. See Section 10 for incompatible materials before handling or use.

Section 8. Exposure controls/personal protection
Control parameters
Occupational exposure Iimits(OSHA United States)
Ingredient name
CAS #
Exposure limits
Titanium Dioxide
13463-67-7
ACGIH TLV (United States, 1/2025) A3.

TWA 8 hours: 2.5 mg/m3. Form: respirable
fraction, finescale particles.

NIOSH REL (United States, 10/2020) NIA.

OSHA PEL (United States, 5/2018)
TWA 8 hours: 15 mg/m3. Form: Total dust.

Zinc Oxide
1314-13-2
ACGIH TLV (United States, 1/2025)
TWA 8 hours: 2 mg/m3. Form: Respirable
fraction.

Page
1969 of 2226
STEL 15 minutes: 10 mg/m3. Form:
ate of issue/Date of revision
: 5/2/2026
Date of previous issue
: 3/4/2026
Version :7.01
4/14

Section 8. Exposure controls/personal protection
Attapulgite Clay
12174-11-7
Respirable fraction.

NIOSH REL (United States, 10/2020)
TWA 10 hours: 5 mg/m3. Form: Dust and
fumes.

STEL 15 minutes: 10 mg/m3. Form: Fume.

CEIL: 15 mg/m3. Form: Dust.

OSHA PEL (United States, 5/2018)
TWA 8 hours: 15 mg/m3. Form: Total dust.

TWA 8 hours: 5 mg/m3. Form: Respirable
fraction.

TWA 8 hours: 5 mg/m3. Form: Fume.

None.

Occupational exposure limits (Canada)
Ingredient name
CAS #
Exposure limits
Zinc Oxide
1314-13-2
CA Saskatchewan Provincial (Canada,
4/2021)
STEL 15 minutes: 10 mg/m3. Form:
respirable dust and fume.

TWA 8 hours: 2 mg/m3. Form: respirable
dust and fume.

CA British Columbia Provincial (Canada,
6/2025)
TWA 8 hours: 2 mg/m3. Form: respirable.

STEL 15 minutes: 10 mg/m3. Form:
respirable.

CA Ontario Provincial (Canada, 6/2019)
TWA 8 hours: 2 mg/m3. Form: respirable
particulate matter.

STEL 15 minutes: 10 mg/m3. Form:
respirable particulate matter.

CA Quebec Provincial (Canada, 2/2024)
TWAEV 8 hours: 2 mg/m3. Form: respirable
aerosol fraction.

STEV 15 minutes: 10 mg/m3. Form:
respirable aerosol fraction.

CA Alberta Provincial (Canada, 3/2023)
OEL 8 hours: 2 mg/m3. Form: respirable.

OEL 15 minutes: 10 mg/m3. Form:
respirable.

Fibres -Natural Mineral Fibres, Attapulgite
12174-11-7
CA Quebec Provincial (Canada, 2/2024)
[Attapulgite] C1.

TWAEV 8 hours: 1 fibers/cm3. Form:

Occupational exposure limits (Mexico)

Page 1970 of 2226 ends

Date of issue/Date of revision : 5/2/2026 Date of previous issue : 3/4/2026 Version :7.01 5/14

Section 8. Exposure controls/personal protection
Ingredient name
CAS #
Exposure limits
Zinc Oxide
1314-13-2
NOM-010-STPS-2014 (Mexico, 4/2016)
TWA 8 hours: 2 mg/m3. Form: Respirable
fraction.

STEL 15 minutes: 10 mg/m3. Form:

Respirable fraction.

Biological exposure indices (United States)
No exposure indices known.

Biological exposure indices (Canada)
No exposure indices known.

Biological exposure indices (Mexico)
No exposure indices known.

Appropriate engineering
controls
Environmental exposure
controls
: If user operations generate dust, fumes, gas, vapor or mist, use process enclosures, local exhaust ventilation or other engineering controls to keep worker exposure to airborne contaminants below any recommended or statutory limits. : Emissions from ventilation or work process equipment should be checked to ensure they comply with the requirements of environmental protection legislation. In some cases, fume scrubbers, filters or engineering modifications to the process equipment will be necessary to reduce emissions to acceptable levels.

Individual protection measures
Hygiene measures
Eye/face protection
Skin protection
Hand protection
Body protection
Other skin protection
Respiratory protection
: Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at the end of the working period.

Appropriate techniques should be used to remove potentially contaminated clothing.

Page 1971 of 2226 ends

Date of issue/Date of revision : 5/2/2026 Date of previous issue : 3/4/2026 Version :7.01 6/14

Section 9. Physical and chemical properties
The conditions of measurement of all properties are at standard temperature and pressure unless otherwise indicated.

Appearance
Physical state
Color
Odor
Odor threshold
pH
Melting point/freezing point
Boiling point or initial
boiling point and boiling
range
Flash point
Evaporation rate
Flammability
Lower and upper explosion
limit/flammability limit
Vapor pressure
Relative vapor density
Relative density
Density
Solubility(ies)
Liquid.

White.

Not available.

9.1 Not available.
100°C (212°F)
: Closed cup: Not applicable.
: 0.09 (butyl acetate = 1)
: Not available.
: Not available.
: 2.3 kPa (17.5 mm Hg)
: 1 [Air= 1]
: 1.18
: 1.17 g/cm3
Media
Result
cold water
Partially soluble
Partition coefficient: n-
octanol/water
Auto -ignition temperature
Decomposition temperature
Viscosity
Molecular weight
Particle characteristics
Median particle size
Heat of combustion
: Not applicable.
: Not available.
: Not available.
: Dynamic (room temperature): Not available.

Kinematic (room temperature): Not available.

Kinematic (40°C (104°F)): >20.5 mm2/s (>20.5 cSt)
: Not applicable.
: Not applicable.
: 0.671 kJ/g
Section 10. Stability and reactivity
Reactivity
Chemical stability
Possibility of hazardous
reactions
Conditions to avoid
: No specific test data related to reactivity available for this product or its ingredients. : The product is stable.
: Under normal conditions of storage and use, hazardous reactions will not occur. : No specific data.

Page 1972 of 2226 ends

Date of issue/Date of revision : 5/2/2026 Date of previous issue : 3/4/2026 Version :7.01 7/14

Section 10. Stability and reactivity
Incompatible materials
: No specific data.

Hazardous decomposition : Under normal conditions of storage and use, hazardous decomposition products should not be produced.
products
Section 11. Toxicological information
Information on toxicological effects
Acute toxicity
Not available.

Conclusion/Summary [Product] : Not available.

Skin corrosion/irritation
Product/ingredient name
Titanium Dioxide
Zinc Oxide
Conclusion/Summary [Product]
Serious eye damage/eye irritation
Product/ingredient name
Zinc Oxide
Conclusion/Summary [Product]
Respiratory corrosion/irritation
Not available.

Conclusion/Summary [Product]
Respiratory or skin sensitization
Not available.

Skin
Conclusion/Summary [Product]
Respiratory
Conclusion/Summary [Product]
Germ cell mutagenicity
Not available.

Result
Human - Skin - Mild irritant
Duration of treatment/exposure: 72 hours
Amount/concentration applied: 300 ug I
Rabbit - Skin - Mild irritant
Duration of treatment/exposure: 24 hours
Amount/concentration applied: 500 mg
: Not available.

Result
Rabbit - Eyes - Mild irritant
Duration of treatment/exposure: 24 hours
Amount/concentration applied: 500 mg
: Not available.
: Not available.
: Not available.
: Not available.

Page 1973 of 2226 ends

Date of issue/Date of revision : 5/2/2026 Date of previous issue : 3/4/2026 Version :7.01 8/14

Section 11. Toxicological information
Conclusion/Summary [Product] : Not available.

Carcinogenicity
Not available.

Conclusion/Summary [Product] : Not available.

Classification
Product/ingredient name
OSHA
IARC
NTP
Titanium Dioxide
Attapulgite Clay
-
-
2B
2B
-
-
Reproductive toxicity
Not available.

Conclusion/Summary [Product] : Not available.

Specific target organ toxicity (single exposure)
Not available.

Specific target organ toxicity (repeated exposure)
Not available.

Aspiration hazard
Not available.

Information on the likely routes of exposure
Not available.

Potential acute health effects
Eye contact
Inhalation
Skin contact
Ingestion
: No known significant effects or critical hazards.
: No known significant effects or critical hazards.
: No known significant effects or critical hazards.
: No known significant effects or critical hazards.

Symptoms related to the physical, chemical and toxicological characteristics Eye contact
Inhalation
Skin contact
Ingestion
: No specific data.
: No specific data.
: No specific data.
: No specific data.

Delayed and immediate effects and also chronic effects from short and long term exposure Short term exposure
Potential immediate : Not available.
effects Page 1974 of 2226
Date of issue/Date of revision : 5/2/2026 Date of previous issue : 3/4/2026 Version :7.01 9/14

Section 11. Toxicological information
Potential delayed effects
Long term exposure
Potential immediate : Not available.
effects
Potential delayed effects : Not available.

Potential chronic health effects
Not available.
: Not available.

Conclusion/Summary [Product] : Not available.

General : No known significant effects or critical hazards.

Carcinogenicity : Suspected of causing cancer. Risk of cancer depends on duration and level of exposure.

Mutagenicity : No known significant effects or critical hazards.

Reproductive toxicity : No known significant effects or critical hazards.

Numerical measures of toxicity
Acute toxicity estimates
N/A
Section 12. Ecological information
Toxicity
Product/ingredient name
Titanium Dioxide
Zinc Oxide
Result
Acute - LC50 - Marine water
Fish - Mummichog - Fundulus heteroclitus
>1000 mg/I [96 hours]
Effect: Mortality
Acute - LC50 - Fresh water
Daphnia - Water flea - Daphnia magna - Neonate
Age: <24 hours
98 pg/I [48 hours]
Effect: Mortality
Acute - LC50 - Fresh water
US EPA
Fish - Rainbow trout,donaldson trout - Oncorhynchus mykiss Weight: 0.78 g

1.1 ppm [96 hours]
Effect: Mortality
Acute - IC50 - Fresh water
Algae - Green algae - Raphidocelis subcapitata - Exponential growth phase
46 pg/l [72 hours]
Effect: Population
Conclusion/Summary [Product] : Not available.

Persistence and degradability
Not available.

Page 1975 of 2226 ends

Date of issue/Date of revision : 5/2/2026 Date of previous issue : 3/4/2026 Version :7.01 10/14

Section 12. Ecological information
Conclusion/Summary [Product]
Bioaccumulative potential
: Not available.

Product/ingredient name
LogP0„,
BCF
Potential
Zinc Oxide
-
28960
High
Mobility in soil
Soil/Water partition
coefficient
: Not available.

Other adverse effects
No known significant effects or critical hazards.

Section 13. Disposal considerations
Disposal methods
: The generation of waste should be avoided or minimized wherever possible. Disposal of this product, solutions and any by-products should at all times comply with the requirements of environmental protection and waste disposal legislation and any regional local authority requirements. Dispose of surplus and non -recyclable products via a licensed waste disposal contractor. Waste should not be disposed of untreated to the sewer unless fully compliant with the requirements of all authorities with jurisdiction.

Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers.

Section 14. Transport information
DOT
Classification
TDG
Classification
Mexico
Classification
IATA
IMDG
UN number
Not regulated.

Not regulated.

UN3082
UN3082
UN proper
shipping name
-
-
-

ENVIRONMENTALLY

HAZARDOUS

SUBSTANCE,
LIQUID, N.O.S.
(Diuron, Zinc
Oxide)

ENVIRONMENTALLY

HAZARDOUS

SUBSTANCE,
LIQUID, N.O.S.
(Diuron, Zinc
Oxide). Marine
pollutant (Zinc
Oxide)
Transport
hazard class(es)
-
-
-
9 t
9 Packing group
-
- -
'
I II
in

Page 976 of 2226 ends

Date of issue/Date of revision
: 5/2/2026
Date of previous issue
: 3/4/2026
Version :7.01
11/14

Section 14. Transport information
Environmental
hazards
No.

No.

Yes.

Additional
-
-
-
This product is
This product is not
information
not regulated as
regulated as a
a dangerous
good when
transported in
sizes of ≤5 L or
≤5 kg, provided
the packagings
meet the general
provisions of

5.0.2.4.1,

5.0.2.6.1.1 and
dangerous good
when transported
in sizes of ≤5 L or
≤5 kg, provided
the packagings
meet the general
provisions of

4.1.1.1, 4.1.1.2
and 4.1.1.4 to

4.1.1.8. 5.0.2.8.

Emergency
schedules F -A, S-
F
Special precautions for user :

Transport in bulk according : Not available.
to IMO instruments
Proper shipping name
: Not available.

Section 15. Regulatory information
U.S. Federal regulations
California Prop. 65
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

International regulations
Montreal Protocol
Not listed.

Stockholm Convention on Persistent Organic Pollutants
Not listed.

International lists
: Australia inventory (AIIC): Not determined.

China inventory (IECSC): Not determined.

Japan inventory (CSCL): Not determined.

Japan inventory (ISHL): Not determined.

Korea inventory (KECI): Not determined.

New Zealand Inventory of Chemicals (NZIoC): Not determined.

Philippines it ggr, gryelFS,pk determined.

Date of issue/Date of revision : 5/2/2026 Date of previous issue : 3/4/2026 Version :7.01 12/14

Section 15. Regulatory information
Taiwan Chemical Substances Inventory (TCSI): Not determined.

Thailand inventory: Not determined.

Turkey inventory: Not determined.

Vietnam inventory: Not determined.

Section 16. Other information
Hazardous Material Information System (U.S.A.)
The customer is responsible for determining the PPE code for this material. For more information on HMIS® Personal Protective Equipment (PPE) codes, consult the HMIS® Implementation Manual.

Procedure used to derive the classification
Classification
Justification
CARCINOGENICITY - Category 2
Calculation method
History
Date of printing
Date of issue/Date of
revision
Date of previous issue
Version
Key to abbreviations
: 5/2/2026
: 5/2/2026
: 3/4/2026
: 7.01
: ATE = Acute Toxicity Estimate
BCF = Bioconcentration Factor
GHS = Globally Harmonized System of Classification and Labelling of Chemicals IATA = International Air Transport Association
IBC = Intermediate Bulk Container
IMDG = International Maritime Dangerous Goods
LogPow = logarithm of the octanol/water partition coefficient MARPOL = International Convention for the Prevention of Pollution From Ships, 1973 as modified by the Protocol of 1978. ("Marpol" = marine pollution) N/A = Not available
SGG = Segregation Group
UN = United Nations
V Indicates information that has changed from previously issued version.

Section 16. Other information
responsible to ensure that his activities comply with all country, federal, state, provincial or local laws. The conditions for use of the product are not under the control of the manufacturer; the customer/buyer/user is responsible to determine the conditions necessary for the safe use of this product. The customer/buyer/user should not use the product for any purpose other than the purpose shown in the applicable section of this SDS without first referring to the supplier and obtaining written handling instructions. Due to the proliferation of sources for information such as manufacturer -specific SDS, the manufacturer cannot be responsible for SDSs obtained from any other source.

Page 1979 of 2226 ends

Date of issue/Date of revision : 5/2/2026 Date of previous issue : 3/4/2026 Version :7.01 14/14

SAFETY DATA SHEET
According to 29 CFR 1910.1200
B66W1310
Section 1. Identification
Product name
Product code
Other means of
identification
Product type : Liquid.
: PRO INDUSTRIALTM PRO-CRYL® Universal Acrylic Primer
Off White
: B66W1310
: Not available.

Relevant identified uses of the substance or mixture and uses advised against Paint or paint related material.

Manufacturer
Emergency telephone
number of the company
Product Information
Telephone Number
: THE SHERWIN-WILLIAMS COMPANY
101 W. Prospect Avenue
Cleveland, OH 44115
: US / Canada: (800) 424-9300
Mexico: SETIQ 800-00-214-00 / 55-5559-1588 Available 24 hours and 365 days a year : US / Canada: (800) 524-5979
Mexico: Not Available
Transportation Emergency : US / Canada: (800) 424-9300
Telephone Number Mexico: SETIQ 800-00-214-00 / 55-5559-1588 Available 24 hours and 365 days a year Section 2. Hazards identification
OSHA/HCS status
Classification of the
substance or mixture
GHS label elements
Hazard pictograms
Signal word
Hazard statements
Precautionary statements
Prevention
: This material is considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200).
: SKIN CORROSION/IRRITATION - Category 2
SERIOUS EYE DAMAGE/ EYE IRRITATION - Category 2A
SKIN SENSITIZATION - Category 1
CARCINOGENICITY - Category 1A
: Danger
: Causes skin irritation.

May cause an allergic skin reaction.

Causes serious eye irritation.

May cause cancer.
: Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Wear protective gloves, protective clothing and eye or face protection. Avoid breathirw,ovapor. Wash thoroughly after handling. Contaminated work clothing muENiiPb144WAIZagf the workplace.

Date of issue/Date of revision : 2/7/2026 Date of previous issue : 8/16/2025 Version :30 1/15

Section 2. Hazards identification
Response
Storage
Disposal
Supplemental label
elements
Hazards not otherwise
classified
Hazards identified when
used
: IF exposed or concerned: Get medical advice or attention. IF ON SKIN: Wash with plenty of water. If skin irritation or rash occurs: Get medical advice or attention. Take off contaminated clothing and wash it before reuse. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice or attention. : Store locked up.
: Dispose of contents and container in accordance with all local, regional, national and international regulations.

WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. FOR INDUSTRIAL USE ONLY.

Adequate ventilation required when sanding or abrading the dried film. If Adequate ventilation cannot be provided wear an approved particulate respirator (NIOSH approved). Follow respirator manufacturer's directions for respirator use. DELAYED EFFECTS FROM LONG TERM OVEREXPOSURE. Abrading or sanding of the dry film may release Crystalline Silica which has been shown to cause lung damage and cancer under long term exposure.

This product contains a TSCA regulated chemical. See Section 15 of the US SDS for details.

Section 3. Composition/information on ingredients
Substance/mixture
Other means of
identification
CAS number/other identifiers
: Mixture
: Not available.

Ingredient name
% by weight
Identifiers
Calcium Carbonate
≥10 - <20
1317-65-3
Titanium Dioxide
≤10
13463-67-7
Polypropylene glycol alkyl phenyl ether
≤1
9064-13-5
Light Aliphatic Hydrocarbon
≤0.3
64742-47-8
Cristobalite, respirable powder
≤0.3
14464-46-1
Any concentration shown as a range is to protect confidentiality or is due to batch variation.

There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are classified and hence require reporting in this section.

Occupational exposure limits, if available, are listed in Section 8.

Section 4. First aid measures
Description of necessary first aid measures
Eye contact
: Immediately flush eyes with plenty of water, occasionally lifting the upper and lower eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10 minutes. Get medical attention.

Page 1981 of 2226 ends

Date of issue/Date of revision : 2/7/2026 Date of previous issue : 8/16/2025 Version :30 2/15

Section 4. First aid measures
Inhalation
Skin contact
Ingestion
Remove victim to fresh air and keep at rest in a position comfortable for breathing. If not breathing, if breathing is irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. Get medical attention. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway.

Loosen tight clothing such as a collar, tie, belt or waistband. : Wash with plenty of soap and water. Remove contaminated clothing and shoes. Wash contaminated clothing thoroughly with water before removing it, or wear gloves.

Continue to rinse for at least 10 minutes. Get medical attention. In the event of any complaints or symptoms, avoid further exposure. Wash clothing before reuse. Clean shoes thoroughly before reuse.
: Wash out mouth with water. Remove dentures if any. If material has been swallowed and the exposed person is conscious, give small quantities of water to drink. Stop if the exposed person feels sick as vomiting may be dangerous. Do not induce vomiting unless directed to do so by medical personnel. If vomiting occurs, the head should be kept low so that vomit does not enter the lungs. Get medical attention. Never give anything by mouth to an unconscious person. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband.

Most important symptoms/effects, acute and delayed
Potential acute health effects
Eye contact : Causes serious eye irritation.

Inhalation
Skin contact
Ingestion
: No known significant effects or critical hazards.
: Causes skin irritation. May cause an allergic skin reaction. : No known significant effects or critical hazards.

Over -exposure signs/symptoms
Eye contact
Inhalation
Skin contact
Ingestion
: Adverse symptoms may include the following:
pain or irritation
watering
redness
: No specific data.
: Adverse symptoms may include the following:
irritation
redness
: No specific data.

Indication of immediate medical attention and special treatment needed, if necessary Notes to physician
Specific treatments
Protection of first-aiders
: Treat symptomatically. Contact poison treatment specialist immediately if large quantities have been ingested or inhaled.
: No specific treatment.
: No action shall be taken involving any personal risk or without suitable training. If it is suspected that fumes are still present, the rescuer should wear an appropriate mask or self-contained breathing apparatus. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. Wash contaminated clothing thoroughly with water before removing it, or wear gloves.

See toxicological information (Section 11)

Page 1982 of 2226 ends

Date of issue/Date of revision : 2/7/2026 Date of previous issue : 8/16/2025 Version :30 3/15

Section 5. Fire -fighting measures
Extinguishing media
Suitable extinguishing
media
Unsuitable extinguishing
media
Specific hazards arising
from the chemical
Hazardous thermal
decomposition products
: Use an extinguishing agent suitable for the surrounding fire. : None known.
: In a fire or if heated, a pressure increase will occur and the container may burst. : Decomposition products may include the following materials:
carbon dioxide
carbon monoxide
metal oxide/oxides
Special protective actions .
for fire-fighters
Special protective
equipment for fire-fighters
Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a fire. No action shall be taken involving any personal risk or without suitable training.

Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face -piece operated in positive pressure mode.

Section 6. Accidental release measures
Personal precautions, protective equipment and emergency procedures For non -emergency : No action shall be taken involving any personal risk or without suitable training. personnel Evacuate surrounding areas. Keep unnecessary and unprotected personnel from entering. Do not touch or walk through spilled material. Avoid breathing vapor or mist.

Provide adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment.

Environmental precautions : This product contains a TSCA regulated chemical. See Section 15 of the US SDS for details.

Methods and materials for containment and cleaning up
Small spill
Large spill
Stop leak if without risk. Move containers from spill area. Absorb with an inert material and place in an appropriate waste disposal container. Dispose of via a licensed waste disposal contractor.

Stop leak if without risk. Move containers from spill area. Approach release from upwind. Prevent entry into sewers, water courses, basements or confined areas. Wash spillages into an effluent treatment plant or proceed as follows. Dispose of via a licensed waste disposal contractor. Contaminated absorbent material may pose the same hazard as the spilled product. Contain and collect spillage with non-combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in container for disposal according to local regulations.

Page 1983 of 2226 ends

Date of issue/Date of revision : 2/7/2026 Date of previous issue : 8/16/2025 Version :30 4/15

Section 7. Handling and storage
Precautions for safe handling
Protective measures
Advice on general
occupational hygiene
: Put on appropriate personal protective equipment (see Section 8). Persons with a history of skin sensitization problems should not be employed in any process in which this product is used. Avoid exposure - obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Do not get in eyes or on skin or clothing. Do not ingest. Avoid breathing vapor or mist. If during normal use the material presents a respiratory hazard, use only with adequate ventilation or wear appropriate respirator. Keep in the original container or an approved alternative made from a compatible material, kept tightly closed when not in use. Empty containers retain product residue and can be hazardous. Do not reuse container. : Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment before entering eating areas. See also Section 8 for additional information on hygiene measures.

Use appropriate containment to avoid environmental contamination. See Section 10 for incompatible materials before handling or use.

Section 8. Exposure controls/personal protection
Control parameters
Occupational exposure limits(OSHA United States)
Ingredient name
CAS #
Exposure limits
Calcium Carbonate
1317-65-3
NIOSH REL (United States, 10/2020)
[calcium carbonate]
TWA 10 hours: 10 mg/m3. Form: Total.

TWA 10 hours: 5 mg/m3. Form: Respirable
fraction.

OSHA PEL (United States, 5/2018)
TWA 8 hours: 15 mg/m3. Form: Total dust.

TWA 8 hours: 5 mg/m3. Form: Respirable
fraction.

Titanium Dioxide
13463-67-7
ACGIH TLV (United States, 1/2025) A3.

TWA 8 hours: 2.5 mg/m3. Form: respirable
fraction, finescale particles.

NIOSH REL (United States, 10/2020) NIA.

OSHA PEL (United States, 5/2018)
TWA 8 hours: 15 mg/m3. Form: Total dust.

Polypropylene glycol alkyl phenyl ether
9064-13-5
None.

Light Aliphatic Hydrocarbon
64742-47-8
ACGIH TLV (United States, 1/2025)
[Kerosene] A3. Absorbed through skin.

TWA 8 hours: 200 mg/m3 (as total
hydrocarbon vapor).

Cristobalite, respirable powder
14464-46-1
ACGIH TLV (United States, 1/2025) [Silica,
crystalline] A2.

TWA 8 hours: 0.025 mg/m3. Form:

Respirable fraction.

NIOSH REL (United States, 10/2020)
Page
1984 of 2226
[SILICA, CRYSTALLINE] NIA.

TWA 10 hours: 0.05 mg/m3. Form:
ate of issue/Date of revision
: 2/7/2026
Date of previous issue
: 8/16/2025
Version :30
5/15

Section 8. Exposure controls/personal protection
respirable dust.

OSHA PEL (United States, 5/2018) [Silica,
crystalline]
TWA 8 hours: 50 pg/m3. Form: Respirable
dust.

OSHA PEL Z3 (United States, 6/2016)
TWA 8 hours: 250 / 2 x (%SiO2+5) mppcf.

Form: Respirable.

TWA 8 hours: 10 / 2 x (%SiO2+2) ►mg/m3.

Form: Respirable.

TWA 8 hours: 30 / 2 x (%SiO2+2) mg/m3.

Form: Total dust.

Occupational exposure limits (Canada)
Ingredient name
CAS #
Exposure limits
Petroleum refining, hydrotreated light distillate
64742-47-8
CA British Columbia Provincial (Canada,?
6/2025) [kerosene/jet fuels] Absorbed
through skin.

TWA 8 hours: 200 mg/m3 (as total
hydrocarbon vapour). Notes: Application
restricted to conditions in which there are
negligible aerosol exposures.

CA Ontario Provincial (Canada, 6/2019)
Absorbed through skin.

TWA 8 hours: 200 mg/m3 (as total
hydrocarbon vapour).

CA Quebec Provincial (Canada, 2/2024)
[kerosene] C3. Absorbed through skin.

TWAEV 8 hours: 200 mg/m3.

CA Alberta Provincial (Canada, 3/2023)
[Kerosene/Jet fuels] Absorbed through skin.

OEL 8 hours: 200 mg/m3 (as total
hydrocarbon vapour).

Cristobalite
14464-46-1
CA Saskatchewan Provincial (Canada,
4/2021)
TWA 8 hours: 0.05 mg/m3. Form: respirable
fraction.

CA British Columbia Provincial (Canada,
6/2025) [silica, crystalline - alpha quartz
and cristobalite] Carc 2A, Carc 1.

TWA 8 hours: 0.025 mg/m3. Form:
respirable.

CA Ontario Provincial (Canada, 6/2019)
TWA 8 hours: 0.05 mg/m3. Form: respirable
particulate matter.

CA Quebec Provincial (Canada, 2/2024)
TWAEV 8 hours: 0.05 mg/m3. Form:
respirable aerosol fraction.

CA Alberta Provincial (Canada, 3/2023) A2.

OEL 8 hours: 0.025 mg/m3. Form:
respirable particulate.

Occupational exposure limits (Mexico)
None.

Page 1985 of 2226 ends

Date of issue/Date of revision : 2/7/2026 Date of previous issue : 8/16/2025 Version :30 6/15

Section 8. Exposure controls/personal protection
Biological exposure indices
No exposure indices known.

Biological exposure indices
No exposure indices known.

Appropriate engineering
controls
Environmental exposure
controls
(United States)
(Canada)
(Mexico)
Individual protection measures
Hygiene measures
Eye/face protection
Skin protection
Hand protection
Body protection
Other skin protection
Respiratory protection
If user operations generate dust, fumes, gas, vapor or mist, use process enclosures, local exhaust ventilation or other engineering controls to keep worker exposure to airborne contaminants below any recommended or statutory limits.

This product contains a TSCA regulated chemical. See Section 15 of the US SDS for details.

Emissions from ventilation or work process equipment should be checked to ensure they comply with the requirements of environmental protection legislation. In some cases, fume scrubbers, filters or engineering modifications to the process equipment will be necessary to reduce emissions to acceptable levels. : Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at the end of the working period.

Appropriate techniques should be used to remove potentially contaminated clothing.

Contaminated work clothing should not be allowed out of the workplace. Wash contaminated clothing before reusing. Ensure that eyewash stations and safety showers are close to the workstation location.
: Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid exposure to liquid splashes, mists, gases or dusts. If contact is possible, the following protection should be worn, unless the assessment indicates a higher degree of protection: chemical splash goggles. : Chemical -resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical products if a risk assessment indicates this is necessary. Considering the parameters specified by the glove manufacturer, check during use that the gloves are still retaining their protective properties. It should be noted that the time to breakthrough for any glove material may be different for different glove manufacturers. In the case of mixtures, consisting of several substances, the protection time of the gloves cannot be accurately estimated. : Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product.
: Appropriate footwear and any additional skin protection measures should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product.
: Based on the hazard and potential for exposure, select a respirator that meets the appropriate standard or certification. Respirators must be used according to a respiratory protection program to ensure proper fitting, training, and other important aspects of use.

Page 1986 of 2226 ends

Date of issue/Date of revision : 2/7/2026 Date of previous issue : 8/16/2025 Version :30 7/15

Section 9. Physical and chemical properties
The conditions of measurement of all properties are at standard temperature and pressure unless otherwise indicated.

White.

Not available.

9.1 Not available.
100°C (212°F)
: Closed cup: Not applicable.
: 0.09 (butyl acetate = 1)
: Not available.
: Not available.
: 2.3 kPa (17.5 mm Hg)
: 1 [Air= 1]
: 1.21
: 1.2 g/cm3
Media
Result
cold water
Partially soluble
Partition coefficient: n-
octanol/water
Auto -ignition temperature
Decomposition temperature
Viscosity
Molecular weight
Particle characteristics
Median particle size
Heat of combustion
: Not applicable.
: Not available.
: Not available.
: Dynamic (room temperature): Not available.

Kinematic (room temperature): Not available.

Kinematic (40°C (104°F)): >20.5 mm2/s (>20.5 cSt)
: Not applicable.
: Not applicable.
: 1.216 kJ/g
Section 10. Stability and reactivity
Reactivity
Chemical stability
Possibility of hazardous
reactions
Conditions to avoid
: No specific test data related to reactivity available for this product or its ingredients. : The product is stable.
: Under normal conditions of storage and use, hazardous reactions will not occur. : No specific data.

Page 1987 of 2226 ends

Date of issue/Date of revision : 2/7/2026 Date of previous issue : 8/16/2025 Version :30 8/15

Section 10. Stability and reactivity
Incompatible materials
: No specific data.

Conclusion/Summary [Product] : Not available.

Skin corrosion/irritation
Product/ingredient name
Titanium Dioxide
Conclusion/Summary [Product]
Serious eye damage/eye irritation
Not available.

Conclusion/Summary [Product]
Respiratory corrosion/irritation
Not available.

Conclusion/Summary [Product]
Respiratory or skin sensitization
Not available.

Skin
Conclusion/Summary [Product]
Respiratory
Conclusion/Summary [Product]
Germ cell mutagenicity
Not available.

Conclusion/Summary [Product]
Result
Human - Skin - Mild irritant
Duration of treatment/exposure: 72 hours
Amount/concentration applied: 300 ug I
: Not available.
: Not available.
: Not available.
: Not available.
: Not available.
: Not available.

Carcinogenicity
Not available.

Page 1988 of 2226 ends

Date of issue/Date of revision : 2/7/2026 Date of previous issue : 8/16/2025 Version :30 9/15

Section 11. Toxicological information
Conclusion/Summary [Product] : Not available.

Classification
Product/ingredient name
OSHA
IARC
NTP
Titanium Dioxide
Cristobalite, respirable
powder
-
+
2B
1 -
Known to be a human carcinogen.

Reproductive toxicity
Not available.

Conclusion/Summary [Product] : Not available.

Specific target organ toxicity (single exposure)
Product/ingredient name
Calcium Carbonate
Specific target organ toxicity (repeated exposure)
Product/ingredient name
Cristobalite, respirable powder
Aspiration hazard
Product/ingredient name
Light Aliphatic Hydrocarbon
Information on the likely routes of exposure
Not available.

Result

SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE)
(Respiratory tract irritation) - Category 3
Result

SPECIFIC TARGET ORGAN TOXICITY (REPEATED
EXPOSURE) (respiratory tract) (inhalation) - Category 1 Result
ASPIRATION HAZARD - Category 1
Potential acute health effects
Eye contact : Causes serious eye irritation.

Inhalation : No known significant effects or critical hazards.

Skin contact : Causes skin irritation. May cause an allergic skin reaction.

Ingestion : No known significant effects or critical hazards.

Symptoms related to the physical, chemical and toxicological characteristics Eye contact
Inhalation
Skin contact
Ingestion
: Adverse symptoms may include the following:
pain or irritation
watering
redness
: No specific data.
: Adverse symptoms may include the following:
irritation
redness
: No specific data.

Page 1989 of 2226 ends

Date of issue/Date of revision : 2/7/2026 Date of previous issue : 8/16/2025 Version :30 10/15

Section 11. Toxicological information
Delayed and immediate effects and also chronic effects from short and long term exposure Short term exposure
Potential immediate : Not available.
effects
Potential delayed effects : Not available.

Long term exposure
Potential immediate
effects
Potential delayed effects : Not available.

Potential chronic health effects
Not available.
: Not available.

Conclusion/Summary [Product] : Not available.

General : Once sensitized, a severe allergic reaction may occur when subsequently exposed to very low levels.

Carcinogenicity : May cause cancer. Risk of cancer depends on duration and level of exposure.

Mutagenicity : No known significant effects or critical hazards.

Reproductive toxicity : No known significant effects or critical hazards.

Numerical measures of toxicity
Acute toxicity estimates
N/A
Section 12. Ecological information
Toxicity
Product/ingredient name
Titanium Dioxide
Light Aliphatic Hydrocarbon
Result
Acute - LC50 - Marine water
Fish - Mummichog - Fundulus heteroclitus
>1000 mg/I [96 hours]
Effect: Mortality
Acute - LC50 - Fresh water
Fish - Bluegill - Lepomis macrochirus
Size: 35 to 75 mm
2200 µg/I [4 days]
Effect: Mortality
Conclusion/Summary [Product] : Not available.

Persistence and degradability
Not available.

Conclusion/Summary [Product] : Not available.

Bioaccumulative potential
Not available.

Page 1990 of 2226 ends

Date of issue/Date of revision : 2/7/2026 Date of previous issue : 8/16/2025 Version :30 11/15

Section 12. Ecological information
Mobility in soil
Soil/Water partition
coefficient
: Not available.

Other adverse effects
No known significant effects or critical hazards.

Section 13. Disposal considerations
Disposal methods
: This product contains a TSCA regulated chemical. See Section 15 of the US SDS for details.

Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers.

Section 14. Transport information
DOT
Classification
TDG
Classification
Mexico
Classification
IATA
IMDG
UN number
Not regulated.

Not regulated.

UN proper
shipping name
-
-
-
-
-
Transport
hazard class(es)
-
-
-
-
-
Packing group
-
-
-
-
-
Environmental
hazards
No.

No.

Additional
information
-
-
-
-
-

Page 1991 of 2226 ends

Date of issue/Date of revision : 2/7/2026 Date of previous issue : 8/16/2025 Version :30 12/15

Section 14. Transport information
Special precautions for user :

Transport in bulk according : Not available.
to IMO instruments
Proper shipping name
: Not available.

Section 15. Regulatory information
U.S. Federal regulations
: TSCA 5(a)2 final significant new use rules: Sodium Nitrite List name Name on list Notes
TSCA 5(a)2 -
Final significant
new use rules
Sodium Nitrite
(Nitrites of
Alkali Metals
(Group IA
elements))
40 CFR 721.4740
California Prop. 65
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

International regulations
Montreal Protocol
Not listed.

Stockholm Convention on Persistent Organic Pollutants
Not listed.

International lists
: Australia inventory (AIIC): Not determined.

China inventory (IECSC): Not determined.

Japan inventory (CSCL): Not determined.

Japan inventory (ISHL): Not determined.

Korea inventory (KECI): Not determined.

New Zealand Inventory of Chemicals (NZIoC): Not determined.

Philippines inventory (PICCS): Not determined.

Taiwan Chemical Substances Inventory (TCSI): Not determined.

Thailand inventory: Not determined.

Turkey inventory: Not determined.

Vietnam inventory: Not determined.

Section 16. Other information
Hazardous Material Information System (U.S.A.)
Flammability
2 0
0 The customer is responsible for determining the PPE code for this material. For more information on HMIS® Personal Protective Equipment (PPE) codes, consult the HMIS® Implementation Manual.

Page 1992 of 2226 ends

Date of issue/Date of revision : 2/7/2026 Date of previous issue : 8/16/2025 Version :30 13/15

Section 16. Other information
Caution: HMIS® ratings are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4 representing significant hazards or risks. Although HMIS® ratings and the associated label are not required on SDSs or products leaving a facility under 29 CFR 1910.1200, the preparer may choose to provide them. HMIS® ratings are to be used with a fully implemented HMIS® program. HMIS® is a registered trademark and service mark of the American Coatings Association, Inc.

Procedure used to derive the classification
Classification
Justification
SKIN CORROSION/IRRITATION - Category 2
SERIOUS EYE DAMAGE/ EYE IRRITATION - Category 2A
SKIN SENSITIZATION - Category 1
CARCINOGENICITY - Category 1A
Calculation method
Calculation method
Calculation method
Calculation method
History
Date of printing
Date of issue/Date of
revision
: 2/7/2026
: 2/7/2026
Date of previous issue : 8/16/2025
Version : 30
Key to abbreviations : ATE = Acute Toxicity Estimate
BCF = Bioconcentration Factor
GHS = Globally Harmonized System of Classification and Labelling of Chemicals IATA = International Air Transport Association
IBC = Intermediate Bulk Container
IMDG = International Maritime Dangerous Goods
LogPow = logarithm of the octanol/water partition coefficient MARPOL = International Convention for the Prevention of Pollution From Ships, 1973 as modified by the Protocol of 1978. ("Marpol" = marine pollution) N/A = Not available
SGG = Segregation Group
UN = United Nations
P Indicates information that has changed from previously issued version.

Page 1993 of 2226 ends

Date of issue/Date of revision : 2/7/2026 Date of previous issue : 8/16/2025 Version :30 14/15

Page 1994 of 2226 ends

Date of issue/Date of revision : 2/7/2026 Date of previous issue : 8/16/2025 Version :30 15/15

SAFETY DATA SHEET
According to 29 CFR 1910.1200
B66W1151
Section 1. Identification
Product name
Product code
Other means of
identification
: PRO INDUSTRIALTM DTM Acrylic Semi -Gloss
Extra White
: B66W1151
: Not available.

Product type : Liquid.

Relevant identified uses of the substance or mixture and uses advised against Paint or paint related material.

Manufacturer
Emergency telephone
number of the company
Product Information
Telephone Number
: THE SHERWIN-WILLIAMS COMPANY
101 W. Prospect Avenue
Cleveland, OH 44115
: US / Canada: (800) 424-9300
Mexico: SETIQ 800-00-214-00 / 55-5559-1588 Available 24 hours and 365 days a year : US / Canada: (800) 524-5979
Mexico: Not Available
Transportation Emergency : US / Canada: (800) 424-9300
Telephone Number Mexico: SETIQ 800-00-214-00 / 55-5559-1588 Available 24 hours and 365 days a year Section 2. Hazards identification
OSHA/HCS status
Classification of the
substance or mixture
GHS label elements
Hazard pictograms
Signal word
Hazard statements
Precautionary statements
Prevention
Response
Storage
Disposal
: This material is considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200).
: CARCINOGENICITY - Category 1A
: Danger
: May cause cancer.
: Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Wear protective gloves, protective clothing and eye or face protection.
: IF exposed or concerned: Get medical advice or attention. : Store locked up.
: Dispose of contents and container in accordance with all local, regional, national and international regulations.

Page 1995 of 2226 ends

Date of issue/Date of revision
: 4/11/2026 Date of previous issue : 3/11/2026
Version : 33.01 1/14

This product contains a TSCA regulated chemical. See Section 15 of the US SDS for details.

Section 3. Composition/information on ingredients
Substance/mixture : Mixture
Other means of : Not available.
identification
CAS number/other identifiers
Ingredient name
% by weight
Identifiers
Titanium Dioxide
≥10 - ≤25
13463-67-7
Attapulgite Clay
≤0.3
12174-11-7
Benzophenone
≤0.3
119-61-9
Cristobalite, respirable powder
≤0.3
14464-46-1
Any concentration shown as a range is to protect confidentiality or is due to batch variation.

There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are classified and hence require reporting in this section.

Occupational exposure limits, if available, are listed in Section 8.

Section 4. First aid measures
Description of necessary first aid measures
Eye contact
Inhalation
Skin contact
: Immediately flush eyes with plenty of water, occasionally lifting the upper and lower eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10 minutes. Get medical attention.
: Remove victim to fresh air and keep at rest in a position comfortable for breathing. If not breathing, if breathing is irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. Get medical attention. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway.

Loosen tight clothing such as a collar, tie, belt or waistband. : Flush contaminated skin with plenty of water. Remove contaminated clothing and shoes. Wash contaminated clothing thoroughly with water before removing it, or wear gloves. Continue to rinse for at least 10 minutes. Get medical attention. Wash clothing before reuse. Clean shoes thoroughly before reuse.

Page 1996 of 2226 ends

Date of issue/Date of revision
: 4/11/2026 Date of previous issue : 3/11/2026
Version :33.01 2/14

Section 4. First aid measures
Ingestion
: Wash out mouth with water. Remove dentures if any. If material has been swallowed and the exposed person is conscious, give small quantities of water to drink. Stop if the exposed person feels sick as vomiting may be dangerous. Do not induce vomiting unless directed to do so by medical personnel. If vomiting occurs, the head should be kept low so that vomit does not enter the lungs. Get medical attention. Never give anything by mouth to an unconscious person. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband.

Most important symptoms/effects, acute and delayed
Potential acute health effects
Eye contact
Inhalation
Skin contact
Ingestion
: No known significant effects or critical hazards.
: No known significant effects or critical hazards.
: No known significant effects or critical hazards.
: No known significant effects or critical hazards.

Over -exposure signs/symptoms
Eye contact
Inhalation
Skin contact
Ingestion
: No specific data.
: No specific data.
: No specific data.
: No specific data.

See toxicological information (Section 11)
Section 5. Fire -fighting measures
Extinguishing media
Suitable extinguishing
media
Unsuitable extinguishing
media
Specific hazards arising
from the chemical
Hazardous thermal
decomposition products
Special protective actions
for fire-fighters
: Use an extinguishing agent suitable for the surrounding fire. : None known.
: In a fire or if heated, a pressure increase will occur and the container may burst. : Decomposition products may include the following materials:
carbon dioxide
carbon monoxide
metal oxide/oxides
: Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a fire. No action shall be taken involving any personal risk or without suitable training. Page 1997 of 2226
Date of issue/Date of revision
: 4/11/2026 Date of previous issue : 3/11/2026
Version :33.01 3/14

Section 5. Fire -fighting measures
Special protective
equipment for fire-fighters
: Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face -piece operated in positive pressure mode.

Evacuate surrounding areas. Keep unnecessary and unprotected personnel from entering. Do not touch or walk through spilled material. Avoid breathing vapor or mist.

Provide adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment.

Environmental precautions
: This product contains a TSCA regulated chemical. See Section 15 of the US SDS for details.

Section 7. Handling and storage
Precautions for safe handling
Protective measures
Advice on general
occupational hygiene
: Put on appropriate personal protective equipment (see Section 8). Avoid exposure - obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Do not get in eyes or on skin or clothing. Do not ingest.

Page 1998 of 2226 ends

Date of issue/Date of revision
: 4/11/2026 Date of previous issue : 3/11/2026
Version :33.01 4/14

Section 7. Handling and storage
Conditions for safe storage, :
including any
incompatibilities
Store in accordance with local regulations. Store in original container protected from direct sunlight in a dry, cool and well -ventilated area, away from incompatible materials (see Section 10) and food and drink. Store locked up. Keep container tightly closed and sealed until ready for use. Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabeled containers.

Use appropriate containment to avoid environmental contamination. See Section 10 for incompatible materials before handling or use.

TWA 8 hours: 2.5 mg/m3. Form: respirable
fraction, finescale particles.

NIOSH REL (United States, 10/2020) NIA.

OSHA PEL (United States, 5/2018)
TWA 8 hours: 15 mg/m3. Form: Total dust.

Attapulgite Clay
12174-11-7
None.

Benzophenone
119-61-9
OARS WEEL (United States, 6/2025)
TWA 8 hours: 0.5 mg/m3.

Cristobalite, respirable powder
14464-46-1
ACGIH TLV (United States, 1/2025) [Silica,
crystalline] A2.

TWA 8 hours: 0.025 mg/m3. Form:

Respirable fraction.

NIOSH REL (United States, 10/2020)
[SILICA, CRYSTALLINE] NIA.

TWA 10 hours: 0.05 mg/m3. Form:
respirable dust.

OSHA PEL (United States, 5/2018) [Silica,
crystalline]
TWA 8 hours: 50 µg/m3. Form: Respirable
dust.

OSHA PEL Z3 (United States, 6/2016)
TWA 8 hours: 250 / 2 x (%SiO2+5) mppcf.

Form: Respirable.

TWA 8 hours: 10 / 2 x (%SiO2+2) mg/m3.

Form: Respirable.

TWA 8 hours: 30 / 2 x (%SiO2+2) mg/m3.

Form: Total dust.

Occupational exposure limits (Canada)
Ingredient name
CAS #
Exposure limits
Fibres -Natural Mineral Fibres, Attapulgite
12174-11-7
CA Quebec Provincial (Canada, 2/2024)
[Attapulgite] C1.

TWAEV 8 hours: 1 fibers/cm3. Form:

Benzophenone
119-61-9
CA British Columbia Provincial (Canada,
6/2025) Carc 2B.

Cristobalite Page
114.4694-o46-121226
CA Saskatchewan Provincial (Canada,
ate of issue/Date of revision
: 4/11/2026
Date of previous issue
: 3/11/2026
Version :33.01
5/14

Section 8. Exposure controls/personal protection
4/2021)
TWA 8 hours: 0.05 mg/m3. Form: respirable
fraction.

CA British Columbia Provincial (Canada,
6/2025) [silica, crystalline - alpha quartz
and cristobalite] Carc 2A, Carc 1.

TWA 8 hours: 0.025 mg/m3. Form:
respirable.

CA Ontario Provincial (Canada, 6/2019)
TWA 8 hours: 0.05 mg/m3. Form: respirable
particulate matter.

CA Quebec Provincial (Canada, 2/2024)
TWAEV 8 hours: 0.05 mg/m3. Form:
respirable aerosol fraction.

CA Alberta Provincial (Canada, 3/2023) A2.

OEL 8 hours: 0.025 mg/m3. Form:
respirable particulate.

Occupational exposure limits (Mexico)
None.

Biological exposure indices (United States)
No exposure indices known.

Biological exposure indices (Canada)
No exposure indices known.

Biological exposure indices (Mexico)
No exposure indices known.

Appropriate engineering
controls
Environmental exposure
controls
Individual protection measures
Hygiene measures
Eye/face protection
Skin protection
If user operations generate dust, fumes, gas, vapor or mist, use process enclosures, local exhaust ventilation or other engineering controls to keep worker exposure to airborne contaminants below any recommended or statutory limits.

This product contains a TSCA regulated chemical. See Section 15 of the US SDS for details.

Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at the end of the working period.

Appropriate techniques should be used to remove potentially contaminated clothing.

Page 2000 of 2226 ends

Date of issue/Date of revision
: 4/11/2026 Date of previous issue : 3/11/2026
Version :33.01 6/14

Section 8. Exposure controls/personal protection
Hand protection
Body protection
Other skin protection
Respiratory protection
Chemical -resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical products if a risk assessment indicates this is necessary. Considering the parameters specified by the glove manufacturer, check during use that the gloves are still retaining their protective properties. It should be noted that the time to breakthrough for any glove material may be different for different glove manufacturers. In the case of mixtures, consisting of several substances, the protection time of the gloves cannot be accurately estimated.

Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product.

Appropriate footwear and any additional skin protection measures should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product.

Based on the hazard and potential for exposure, select a respirator that meets the appropriate standard or certification. Respirators must be used according to a respiratory protection program to ensure proper fitting, training, and other important aspects of use.

Section 9. Physical and chemical properties
The conditions of measurement of all properties are at standard temperature and pressure unless otherwise indicated.

Appearance
Physical state
Color
Odor
Odor threshold
pH
Melting point/freezing point .

Boiling point or initial
boiling point and boiling
range
Flash point
Evaporation rate
Flammability
Lower and upper explosion .
limit/flammability limit
Vapor pressure
Relative vapor density
Relative density
Density
Solubility(ies)
Liquid.

White.

Not available.

Not available.
9 Not available.
100°C (212°F)
Closed cup: Not applicable.

0.09 (butyl acetate = 1)
Not available.

Lower: 0.6%
Upper: 4.2%

2.3 kPa (17.5 mm Hg)
1 [Air= 1]

1.22 1.22 g/cm3
Media
Result
cold water
Partially soluble
Partition coefficient: n-
octanol/water
: Not applicable.

Auto -ignition temperature .

Decomposition temperature :

Viscosity
Not available.

Not available.

Dynamic (room temperature): Not available.

Kinematic (40°C pe 2)T ilabl0.

Kinematic (40°C ( ). 0. (>20.5 cSt)
Date of issue/Date of revision
: 4/11/2026 Date of previous issue : 3/11/2026
Version :33.01 7/14

Section 9. Physical and chemical properties
Molecular weight
Particle characteristics
Median particle size
Heat of combustion
: Not applicable.
: Not applicable.
: 0.831 kJ/g
Section 10. Stability and reactivity
Reactivity
Chemical stability
Possibility of hazardous
reactions
: No specific test data related to reactivity available for this product or its ingredients. : The product is stable.
: Under normal conditions of storage and use, hazardous reactions will not occur.

Conditions to avoid : No specific data.

Incompatible materials : No specific data.

Hazardous decomposition
products
: Under normal conditions of storage and use, hazardous decomposition products should not be produced.

Section 11. Toxicological information
Information on toxicological effects
Acute toxicity
Product/ingredient name
Benzophenone
Conclusion/Summary [Product]
Skin corrosion/irritation
Product/ingredient name
Titanium Dioxide
Conclusion/Summary [Product]
Serious eye damage/eye irritation
Not available.

Conclusion/Summary [Product]
Respiratory corrosion/irritation
Not available.

Result
Rat - Oral - LD50
>10 g/kg
Rabbit - Dermal - LD50
3535 mg/kg
: Not available.

Result
Human - Skin - Mild irritant
Duration of treatment/exposure: 72 hours
Amount/concentration applied: 300 ug I
: Not available.
: Not available.

Page 2002 of 2226 ends

Date of issue/Date of revision : 4/11/2026 Date of previous issue : 3/11/2026 Version :33.01 8/14

Section 11. Toxicological information
Conclusion/Summary [Product]
Respiratory or skin sensitization
Not available.
: Not available.

Skin
Conclusion/Summary [Product] : Not available.

Respiratory
Conclusion/Summary [Product] : Not available.

Germ cell mutagenicity
Not available.

Conclusion/Summary [Product] : Not available.

Carcinogenicity
Not available.

Conclusion/Summary [Product] : Not available.

Classification
Product/ingredient name
OSHA
IARC
NTP
Titanium Dioxide
Attapulgite Clay
Benzophenone
Cristobalite, respirable
powder
-
-
-
+
2B
2B
2B
1 -
-
-
Known to be a human carcinogen.

Reproductive toxicity
Not available.

Conclusion/Summary [Product] : Not available.

Specific target organ toxicity (single exposure)
Not available.

Specific target organ toxicity (repeated exposure)
Product/ingredient name
Benzophenone
Cristobalite, respirable powder
Aspiration hazard
Not available.

Result

SPECIFIC TARGET ORGAN TOXICITY (REPEATED
EXPOSURE) - Category 2

SPECIFIC TARGET ORGAN TOXICITY (REPEATED
EXPOSURE) (respiratory tract) (inhalation) - Category 1

Page 2003 of 2226 ends

Date of issue/Date of revision
: 4/11/2026 Date of previous issue : 3/11/2026
Version :33.01 9/14

Section 11. Toxicological information
Information on the likely routes of exposure
Not available.

Potential acute health effects
Eye contact
Inhalation
Skin contact
Ingestion
No known significant effects or critical hazards.

No known significant effects or critical hazards.

Symptoms related to the physical, chemical and toxicological characteristics Eye contact
Inhalation
Skin contact
Ingestion
No specific data.

No specific data.

Delayed and immediate effects and also chronic effects from short and long term exposure Short term exposure
Potential immediate
effects
Potential delayed effects .

Long term exposure
Potential immediate
effects
Potential delayed effects .

Potential chronic health effects
Not available.

Not available.

Conclusion/Summary [Product] : Not available.

General
Carcinogenicity
Mutagenicity
Reproductive toxicity
: No known significant effects or critical hazards.
: May cause cancer. Risk of cancer depends on duration and level of exposure. : No known significant effects or critical hazards.
: No known significant effects or critical hazards.

Numerical measures of toxicity
Acute toxicity estimates
Product/ingredient name
Oral (mg/
kg)
Dermal
(mg/kg)
Inhalation
(gases)
(ppm)
Inhalation
(vapors)
(mg/I)
Inhalation
(dusts
and mists)
(mg/I)
Benzophenone
500
3535
N/A
N/A
N/A

Page 2004 of 2226 ends

Date of issue/Date of revision
: 4/11/2026 Date of previous issue : 3/11/2026
Version :33.01 10/14

Section 12. Ecological information
Toxicity
Product/ingredient name
Titanium Dioxide
Benzophenone
Result
Acute - LC50 - Marine water
Fish - Mummichog - Fundulus heteroclitus
>1000 mg/I [96 hours]
Effect: Mortality
Acute - LC50 - Fresh water
Fish - Fathead minnow - Pimephales promelas - Larvae
Aqe: <24 hours

10.89 mg/I [96 hours]
Effect: Mortality
Chronic - NOEC - Fresh water
Fish - Fathead minnow - Pimephales promelas - Embryo
Aqe: <24 hours

1.03 mg/I [32 days]
Effect: Growth
Conclusion/Summary [Product] : Not available.

Persistence and degradability
Not available.

Conclusion/Summary [Product] : Not available.

Bioaccumulative potential
Product/ingredient name
LogPow
BCF
Potential
Benzophenone
-

12.02 Low
Mobility in soil
Soil/Water partition
coefficient
: Not available.

Other adverse effects
No known significant effects or critical hazards.

Section 13. Disposal considerations
Disposal methods
: This product contains a TSCA regulated chemical. See Section 15 of the US SDS for details.

Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers.

Page 2005 of 2226 ends

Date of issue/Date of revision
: 4/11/2026 Date of previous issue : 3/11/2026
Version :33.01 11/14

Section 14. Transport information
DOT
Classification
TDG
Classification
Mexico
Classification
IATA
IMDG
UN number
Not regulated.

Not regulated.

UN proper
shipping name
-
-
-
-
-
Transport
hazard class(es)
-
-
-
-
-
Packing group
-
-
-
-
-
Environmental
hazards
No.

No.

Additional
information
-
-
-
-
-
Special precautions for user :

Transport in bulk according : Not available.
to IMO instruments
Proper shipping name
: Not available.

Section 15. Regulatory information
U.S. Federal regulations
: TSCA 5(a)2 final significant new use rules: Sodium Nitrite List name Name on list Notes
TSCA 5(a)2 - Sodium Nitrite 40 CFR 721.4740
Final significant (Nitrites of
new use rules Alkali Metals
(Group IA
elements))
TSCA 5(e) substance consent order: Fluoropolymer
List name Name on list Notes
TSCA 5(e) - Partially
Substances fluorinated
consent order alcohol,
reaction
products with
phosphorus
oxide (P2O5),
ammonium
salts
(PR Page 20)06 of 2226
Date of issue/Date of revision
: 4/11/2026 Date of previous issue : 3/11/2026
Version :33.01 12/14

Section 15. Regulatory information
California Prop. 65
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

International regulations
Montreal Protocol
Not listed.

Stockholm Convention on Persistent Organic Pollutants
Not listed.

International lists
: Australia inventory (AIIC): Not determined.

China inventory (IECSC): Not determined.

Japan inventory (CSCL): Not determined.

Japan inventory (ISHL): Not determined.

Korea inventory (KECI): Not determined.

New Zealand Inventory of Chemicals (NZIoC): Not determined.

Philippines inventory (PICCS): Not determined.

Taiwan Chemical Substances Inventory (TCSI): Not determined.

Thailand inventory: Not determined.

Turkey inventory: Not determined.

Vietnam inventory: Not determined.

Section 16. Other information
Hazardous Material Information System (U.S.A.)
* 0
0 0
Flammability
The customer is responsible for determining the PPE code for this material. For more information on HMIS® Personal Protective Equipment (PPE) codes, consult the HMIS® Implementation Manual.

Procedure used to derive the classification
Classification
Justification
CARCINOGENICITY - Category 1A
Calculation method
History
Date of printing
Date of issue/Date of
revision
: 4/11/2026
: 4/11/2026
Date of previous issue : 3/11/2026
Version : 33.01

Page 2007 of 2226 ends

Date of issue/Date of revision
: 4/11/2026 Date of previous issue : 3/11/2026
Version :33.01 13/14

Section 16. Other information
Key to abbreviations
: ATE = Acute Toxicity Estimate
BCF = Bioconcentration Factor
GHS = Globally Harmonized System of Classification and Labelling of Chemicals IATA = International Air Transport Association
IBC = Intermediate Bulk Container
IMDG = International Maritime Dangerous Goods
LogPow = logarithm of the octanol/water partition coefficient MARPOL = International Convention for the Prevention of Pollution From Ships, 1973 as modified by the Protocol of 1978. ("Marpol" = marine pollution) N/A = Not available
SGG = Segregation Group
UN = United Nations
17 Indicates information that has changed from previously issued version.

Page 2008 of 2226 ends

Date of issue/Date of revision
: 4/11/2026 Date of previous issue : 3/11/2026
Version :33.01 14/14

SAFETY DATA SHEET
According to 29 CFR 1910.1200
B53W5151
Section 1. Identification
Product name
Product code
Other means of
identification
: PRO INDUSTRIALTM Waterbased Alkyd Urethane Semi -Gloss Extra White
: B53W5151
: Not available.

Product type : Liquid.

Relevant identified uses of the substance or mixture and uses advised against Paint or paint related material.

Manufacturer
Emergency telephone
number of the company
Product Information
Telephone Number
: THE SHERWIN-WILLIAMS COMPANY
101 W. Prospect Avenue
Cleveland, OH 44115
: US / Canada: (800) 424-9300
Mexico: SETIQ 800-00-214-00 / 55-5559-1588 Available 24 hours and 365 days a year : US / Canada: (800) 524-5979
Mexico: Not Available
Transportation Emergency : US / Canada: (800) 424-9300
Telephone Number Mexico: SETIQ 800-00-214-00 / 55-5559-1588 Available 24 hours and 365 days a year Section 2. Hazards identification
OSHA/HCS status
Classification of the
substance or mixture
GHS label elements
Hazard pictograms
Signal word
Hazard statements
Precautionary statements
Prevention
Response
Storage
Disposal
: This material is considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200).
: CARCINOGENICITY - Category 2
TOXIC TO REPRODUCTION - Category 2
: Warning
: Suspected of causing cancer.

Suspected of damaging fertility or the unborn child.

Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Wear protective gloves, protective clothing and eye or face protection.

IF exposed or concerned: Get medical advice or attention.

Store locked up.

Dispose of contents and container in accordance with all local, regional, national and international reguR33 t :.2009 of 2226
Date of issue/Date of revision
: 4/11/2026 Date of previous issue : 12/30/2025
Version :6.02 1/14

This product contains a TSCA regulated chemical. See Section 15 of the US SDS for details.

Section 3. Composition/information on ingredients
Substance/mixture
Other means of
identification
CAS number/other identifiers
: Mixture
: Not available.

Ingredient name
% by weight
Identifiers
Titanium Dioxide
≥10 - ≤25
13463-67-7
Attapulgite Clay
≤1
12174-11-7
2-Ethyl-2-(hydroxymethyl)-1,3-propanediol
≤0.3
77-99-6
Any concentration shown as a range is to protect confidentiality or is due to batch variation.

There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are classified and hence require reporting in this section.

Occupational exposure limits, if available, are listed in Section 8.

Section 4. First aid measures
Description of necessary first aid measures
Eye contact
Inhalation
Skin contact
Ingestion
Immediately flush eyes with plenty of water, occasionally lifting the upper and lower eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10 minutes. Get medical attention.

Remove victim to fresh air and keep at rest in a position comfortable for breathing. If not breathing, if breathing is irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. Get medical attention. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway.

Loosen tight clothing such as a collar, tie, belt or waistband.

Flush contaminated skin with plenty of water. Remove contaminated clothing and shoes. Continue to rinse for at least 10 minutes. Get medical attention. Wash clothing before reuse. Clean shoes thoroughly before reuse.

Wash out mouth with water. Remove dentures if any. If material has been swallowed and the exposed person is conscious, give small quantities of water to drink. Stop if the exposed person feels sick as vomiting may be dangerous. Do not induce vomiting unless directed to do so by medical personnel. If vomiting occurs, the head should be kept low so that vomit does not enter the lungs. Get medical attention. Never give anything by mouth to an unconscious person. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband.

Most important symptoms/effects, acute and delayed
Potential acute health effects

Page 2010 of 2226 ends

Date of issue/Date of revision
: 4/11/2026 Date of previous issue : 12/30/2025
Version :6.02 2/14

Section 4. First aid measures
Eye contact
Inhalation
Skin contact
Ingestion
: No known significant effects
: No known significant effects
: No known significant effects
: No known significant effects
Over -exposure signs/symptoms
Eye contact
Inhalation
Skin contact
Ingestion
or critical hazards.
or critical hazards.
or critical hazards.
or critical hazards.
: No specific data.
: Adverse symptoms may include the following:
reduced fetal weight
increase in fetal deaths
skeletal malformations
: Adverse symptoms may include the following:
reduced fetal weight
increase in fetal deaths
skeletal malformations
: Adverse symptoms may include the following:
reduced fetal weight
increase in fetal deaths
skeletal malformations
Indication of immediate medical attention and special treatment needed, if necessary Notes to physician
Specific treatments
Protection of first-aiders
: Treat symptomatically. Contact poison treatment specialist immediately if large quantities have been ingested or inhaled.

No specific treatment.
: No action shall be taken involving any personal risk or without suitable training. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation.

See toxicological information (Section 11)
Section 5. Fire -fighting measures
Extinguishing media
Suitable extinguishing
media
Unsuitable extinguishing
media
Specific hazards arising
from the chemical
Hazardous thermal
decomposition products
Special protective actions
for fire-fighters
Special protective
equipment for fire-fighters
: Use an extinguishing agent suitable for the surrounding fire. : None known.
: In a fire or if heated, a pressure increase will occur and the container may burst. : Decomposition products may include the following materials:
metal oxide/oxides
Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a fire. No action shall be taken involving any personal risk or without suitable training.

Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face -piece operated in positive pressure mode.

Page 2011 of 2226 ends

Date of issue/Date of revision : 4/11/2026 Date of previous issue : 12/30/2025
Version :6.02 3/14

Evacuate surrounding areas. Keep unnecessary and unprotected personnel from entering. Do not touch or walk through spilled material. Avoid breathing vapor or mist.

Provide adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment.

Environmental precautions
: This product contains a TSCA regulated chemical. See Section 15 of the US SDS for details.

Section 7. Handling and storage
Precautions for safe handling
Protective measures
Advice on general
occupational hygiene
: Put on appropriate personal protective equipment (see Section 8). Avoid exposure - obtain special instructions before use. Avoid exposure during pregnancy. Do not handle until all safety precautions have been read and understood. Do not get in eyes or on skin or clothing. Do not ingest. Avoid breathing vapor or mist. If during normal use the material presents a respiratory hazard, use only with adequate ventilation or wear appropriate respirator. Keep in the original container or an approved alternative made from a compatible material, kept tightly closed when not in use. Empty containers retain product residue and can be hazardous. Do not reuse container. : Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment before entering eating areas. See also Section 8 for additional information on hygiene measures.

Use appropriate containment to avoid environmental contamination. See Section 10 for incompatible materials before handling or use.

Page 2012 of 2226 ends

Date of issue/Date of revision
: 4/11/2026 Date of previous issue : 12/30/2025
Version :6.02 4/14

TWA 8 hours: 2.5 mg/m3. Form: respirable
fraction, finescale particles.

NIOSH REL (United States, 10/2020) NIA.

OSHA PEL (United States, 5/2018)
TWA 8 hours: 15 mg/m3. Form: Total dust.

Attapulgite Clay
12174-11-7
None.
2-Ethyl-2-(hydroxymethyl)-1,3-propanediol
77-99-6
ACGIH TLV (United States, 1/2025)
TWA 8 hours: 0.5 ppm. Form: Inhalable
fraction and vapor.

Occupational exposure limits (Canada)
Ingredient name
CAS #
Exposure limits
Fibres -Natural Mineral Fibres, Attapulgite
12174-11-7
CA Quebec Provincial (Canada, 2/2024) a
[Attapulgite] C1.

TWAEV 8 hours: 1 fibers/cm'. Form:

RESPIRABLE FIBRES (other than respirable
asbestos fibres) : Objects, other than
respirable asbestos fibres, longer than 5 pm,
having a diameter of less than 3 pm and a
ratio of length to diameter of more than 3 : 1..
2-Ethyl-2-(hydroxymethyl)-1,3-propanediol
77-99-6
CA British Columbia Provincial (Canada,
6/2025) Repr. Notes: No British Columbia
exposure limit at this time
Occupational exposure limits (Mexico)
Ingredient name
CAS #
Exposure limits
2-Ethyl-2-(hydroxymethyl)-1,3-propanediol
77-99-6
ACGIH TLV (United States, 1/2025) 7
TWA 8 hours: 0.5 ppm. Form: Inhalable
fraction and vapor.

Biological exposure indices (United States)
No exposure indices known.

Biological exposure indices (Canada)
No exposure indices known.

Biological exposure indices (Mexico)
No exposure indices known.

Appropriate engineering
controls
Environmental exposure
controls
If user operations generate dust, fumes, gas, vapor or mist, use process enclosures, local exhaust ventilation or other engineering controls to keep worker exposure to airborne contaminants below any recommended or statutory limits.

This product contains a TSCA regulated chemical. See Section 15 of the US SDS for details.

Page 2013 of 2226 ends

Date of issue/Date of revision
: 4/11/2026 Date of previous issue : 12/30/2025
Version :6.02 5/14

Section 8. Exposure controls/personal protection
Individual protection measures
Hygiene measures
Eye/face protection
Skin protection
Hand protection
: Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at the end of the working period.

Appropriate techniques should be used to remove potentially contaminated clothing.

Body protection : Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product.

Other skin protection : Appropriate footwear and any additional skin protection measures should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product.

Respiratory protection : Based on the hazard and potential for exposure, select a respirator that meets the appropriate standard or certification. Respirators must be used according to a respiratory protection program to ensure proper fitting, training, and other important aspects of use.

Section 9. Physical and chemical properties
The conditions of measurement of all properties are at standard temperature and pressure unless otherwise indicated.

Appearance
Physical state
Color
: Liquid.
: White.

Odor : Not available.

Odor threshold : Not available.
pH : 9
Melting point/freezing point : Not available.

Boiling point or initial : 100°C (212°F)
boiling point and boiling
range
Flash point : Closed cup: Not applicable.

Evaporation rate : 0.09 (butyl acetate = 1)
Flammability : Not available.

Lower and upper explosion : Not available.
limit/flammability limit
Vapor pressure
Relative vapor density
Relative density
: 2.3 kPa (17.5 mm Hg)
: 1 [Air= 1]
: 1.28

Page 2014 of 2226 ends

Date of issue/Date of revision
: 4/11/2026 Date of previous issue : 12/30/2025
Version :6.02 6/14

Section 9. Physical and chemical properties
Density
Solubility(ies)
: 1.28 g/cm3
Media
Result
cold water
Partially soluble
Partition coefficient: n-
octanol/water
Auto -ignition temperature
Decomposition temperature
Viscosity
Molecular weight
Particle characteristics
Median particle size
Heat of combustion
: Not applicable.
: Not available.
: Not available.
: Dynamic (room temperature): Not available.

Kinematic (room temperature): Not available.

Kinematic (40°C (104°F)): >20.5 mm2/s (>20.5 cSt)
: Not applicable.
: Not applicable.
: 0.431 kJ/g
Section 10. Stability and reactivity
Reactivity
Chemical stability
Possibility of hazardous
reactions
Conditions to avoid
Incompatible materials
Hazardous decomposition
products
: No specific test data related to reactivity available for this product or its ingredients. : The product is stable.
: Under normal conditions of storage and use, hazardous reactions will not occur. : No specific data.
: No specific data.
: Under normal conditions of storage and use, hazardous decomposition products should not be produced.

Section 11. Toxicological information
Information on toxicological effects
Acute toxicity
Product/ingredient name
2-Ethyl-2-(hydroxymethyl)-1,3-propanediol
Result
Rat - Oral - LD50
14000 mg/kg
Conclusion/Summary [Product] : Not available.

Skin corrosion/irritation
Product/ingredient name
Titanium Dioxide
Result
Human - Skin - Mild irritant
Duration of treatment/exposure: 72 hours
Amount/concentration applied: 300 ug I
Conclusion/Summary [Product]
Not a we2015 of 2226
Date of issue/Date of revision : 4/11/2026 Date of previous issue : 12/30/2025 Version :6.02 7/14

Section 11. Toxicological information
Serious eye damage/eye irritation
Not available.

Conclusion/Summary [Product] : Not available.

Respiratory corrosion/irritation
Not available.

Conclusion/Summary [Product] : Not available.

Respiratory or skin sensitization
Not available.

Skin
Conclusion/Summary [Product] : Not available.

Respiratory
Conclusion/Summary [Product] : Not available.

Germ cell mutagenicity
Not available.

Conclusion/Summary [Product] : Not available.

Carcinogenicity
Not available.

Conclusion/Summary [Product] : Not available.

Classification
Product/ingredient name
OSHA
IARC
NTP
Titanium Dioxide
Attapulgite Clay
-
-
2B
2B
-
-
Reproductive toxicity
Not available.

Conclusion/Summary [Product] : Not available.

Specific target organ toxicity (single exposure)
Not available.

Specific target organ toxicity (repeated exposure)
Not available.

Page 2016 of 2226 ends

Date of issue/Date of revision
: 4/11/2026 Date of previous issue : 12/30/2025
Version :6.02 8/14

Section 11. Toxicological information
Aspiration hazard
Not available.

Information on the likely routes of exposure
Not available.

Symptoms related to the physical, chemical and toxicological characteristics Eye contact
Inhalation
Skin contact
Ingestion
: No specific data.
: Adverse symptoms may include the following:
reduced fetal weight
increase in fetal deaths
skeletal malformations
: Adverse symptoms may include the following:
reduced fetal weight
increase in fetal deaths
skeletal malformations
: Adverse symptoms may include the following:
reduced fetal weight
increase in fetal deaths
skeletal malformations
Delayed and immediate effects and also chronic effects from short and long term exposure Short term exposure
Potential immediate : Not available.
effects
Potential delayed effects : Not available.

Long term exposure
Potential immediate : Not available.
effects
Potential delayed effects : Not available.

Potential chronic health effects
Not available.

Conclusion/Summary [Product] : Not available.

General : No known significant effects or critical hazards.

Carcinogenicity : Suspected of causing cancer. Risk of cancer depends on duration and level of exposure.

Mutagenicity : No known significant effects or critical hazards.

Reproductive toxicity : Suspected of damaging fertility or the unborn child.

Numerical measures of toxicity

Page 2017 of 2226 ends

Date of issue/Date of revision
: 4/11/2026 Date of previous issue : 12/30/2025
Version :6.02 9/14

Section 11. Toxicological information
Acute toxicity estimates
Product/ingredient name
Oral (mg/
kg)
Dermal
(mg/kg)
Inhalation
(gases)
(ppm)
Inhalation
(vapors)
(mg/I)
Inhalation
(dusts
and mists)
(mg/I)
2-Ethyl-2-(hydroxymethyl)-1,3-propanediol
14000
N/A
N/A
N/A
N/A
Section 12. Ecological information
Toxicity
Product/ingredient name
Titanium Dioxide
2-Ethyl-2-(hydroxymethyl)-1,3-propanediol
Result
Acute - LC50 - Marine water
Fish - Mummichog - Fundulus heteroclitus
>1000 mg/I [96 hours]
Effect: Mortality
Acute - EC50 - Fresh water
Daphnia - Water flea - Daphnia magna
Age: 1 to 3 days
13 gll [48 hours]
Effect: Intoxication
Acute - LC50 - Marine water
Fish - Sheepshead minnow - Cyprinodon variegatus

14.4 g/I [96 hours]
Effect: Mortality
Conclusion/Summary [Product] : Not available.

Persistence and degradability
Not available.

Conclusion/Summary [Product] : Not available.

Bioaccumulative potential
N
Product/ingredient name
LogP0W
BCF
Potential
2-Ethyl-2-(hydroxymethyl)
-1,3-propanediol
-
<1 [OECD 305 C]
Low
Mobility in soil
Soil/Water partition
coefficient
: Not available.

Other adverse effects
No known significant effects or critical hazards.

Page 2018 of 2226 ends

Date of issue/Date of revision
: 4/11/2026 Date of previous issue : 12/30/2025
Version :6.02 10/14

Section 13. Disposal considerations
Disposal methods
: This product contains a TSCA regulated chemical. See Section 15 of the US SDS for details.

Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers.

Section 14. Transport information
DOT
Classification
TDG
Classification
Mexico
Classification
IATA
IMDG
UN number
Not regulated.

Not regulated.

UN proper
shipping name
-
-
-
-
-
Transport
hazard class(es)
-
-
-
-
-
Packing group
-
-
-
-
-
Environmental
hazards
No.

No.

Additional
information
-
-
-
-
-
Special precautions for user :

Transport in bulk according : Not available.
to IMO instruments
Proper shipping name : Not available.

Page 2019 of 2226 ends

Date of issue/Date of revision
: 4/11/2026 Date of previous issue : 12/30/2025
Version : 6.02 11/14

Section 15. Regulatory information
U.S. Federal regulations
: TSCA 5(a)2 final significant new use rules: Sodium Nitrite; Chlorodiazocarboxylate List name Name on list Notes
40 CFR 721.4740
TSCA 5(a)2 -
Final significant
new use rules
Sodium Nitrite
(Nitrites of
Alkali Metals
(Group IA
elements))
TSCA 5(a)2 - Iron(1+), chloro 40 CFR 721.10414
Final significant [rel-
new use rules 1,5-dimethyl
(1 R,2S,4R,5S)
- 9,9-dihydroxy-
3-methyl-2,4-di
(2-pyridinyl-.
kappa. N)-7-[
(2-pyridinyl-.
kappa.N)methyl]
- 3,7-diazabicyclo
[3.3.1]nonane-
1,5-dicarboxylate-
.kappa.N3,.
kappa.N7]-,
chloride (1:1),
(OC-6-63)-
TSCA 5(e) substance consent order: Chlorodiazocarboxylate List name Name on list Notes
TSCA 5(e) - Iron(1+), chloro
Substances [rel-
consent order 1,5-dimethyl
(1 R,2S,4R,5S)
- 9,9-dihydroxy-
3-methyl-2,4-di
(2-pyridinyl-.
kappa.N)-7-[
(2-pyridinyl-.
kappa.N)methyl]
-3,7-diazabicyclo
[3.3.1 ]nonane-
1,5-dicarboxylate-
.kappa.N3,.
kappa.N7]-,
chloride (1:1),
(OC-6-63)-
N
California Prop. 65
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

International regulations
Montreal Protocol
Not listed.

Stockholm Convention on Persistent Organic Pollutants
Not listed.

International lists
: Australia inventory (AIIC): Not determined.

China inventory (IECSC): Not determined.

Japan inventory (CSCL): Not determined.

Japan inventory (ISHL): Not determined.

Korea inventory (KECI): Not determined.

New Zealand Inventory of Chemicals (NZIoC): Not determined.

Philippines inventory (PICCS): Not determined.

Taiwan Chemical Substances Inventory (TCSI): Not determined.

Thailand invepage MM0ISfr228.

Date of issue/Date of revision
: 4/11/2026 Date of previous issue : 12/30/2025
Version :6.02 12/14

Section 15. Regulatory information
Turkey inventory: Not determined.

Vietnam inventory: Not determined.

Section 16. Other information
Hazardous Material Information System (U.S.A.)
* 0
0 0
Flammability
Physical hazards
The customer is responsible for determining the PPE code for this material. For more information on HMIS® Personal Protective Equipment (PPE) codes, consult the HMIS® Implementation Manual.

Procedure used to derive the classification
Classification
Justification
CARCINOGENICITY - Category 2
TOXIC TO REPRODUCTION - Category 2
Calculation method
Calculation method
History
Date of printing
Date of issue/Date of
revision
: 4/11/2026
: 4/11/2026
Date of previous issue : 12/30/2025
Version : 6.02
Key to abbreviations : ATE = Acute Toxicity Estimate
BCF = Bioconcentration Factor
GHS = Globally Harmonized System of Classification and Labelling of Chemicals IATA = International Air Transport Association
IBC = Intermediate Bulk Container
IMDG = International Maritime Dangerous Goods
LogPow = logarithm of the octanol/water partition coefficient MARPOL = International Convention for the Prevention of Pollution From Ships, 1973 as modified by the Protocol of 1978. ("Marpol" = marine pollution) N/A = Not available
SGG = Segregation Group
UN = United Nations
17 Indicates information that has changed from previously issued version.

Notice to reader
It is recommended that each customer or recipient of this Safety Data Sheet (SDS) study it carefully and consult resources, as necessary or appropriate, to become aware of and understand the data contained in this SDS and any hazards associated with the product. This information is provided in good faith and believed to be accurate as of the effective date herein. However, no warranty, express or implied, is given. The information presented here applies only to the product as shipped. The addition of any material can change the composition, hazards and risks of the product. Products shall not be repackaged, modified, or tinted except as specifically instructed by the manufacturer, including but not limited to the incorporation of products not specified by the manufacturer, or the use or addition of products in proportions not specified by the manufacturer. Regulatory requirements are subject to change and may differ between various locations and jurisdictions. The customer/buyer/user is responsible to ensure that his activities comply with Innc,.9tent e.j eral, state, provincial or local laws. The conditions for use of the product are not under tI & tf 6II o4 6, nufacturer; the customer/buyer/user is Date of issue/Date of revision : 4/11/2026 Date of previous issue : 12/30/2025 Version : 6.02 13/14

Section 16. Other information
responsible to determine the conditions necessary for the safe use of this product. The customer/buyer/user should not use the product for any purpose other than the purpose shown in the applicable section of this SDS without first referring to the supplier and obtaining written handling instructions. Due to the proliferation of sources for information such as manufacturer -specific SDS, the manufacturer cannot be responsible for SDSs obtained from any other source.

Page 2022 of 2226 ends

Date of issue/Date of revision
: 4/11/2026 Date of previous issue : 12/30/2025
Version :6.02 14/14

Page 2023 of 2226 ends

CITY OF BEAUMONT

PUBLIC WORKS AGREEMENT
This PUBLIC WORKS AGREEMENT ("Agreement") is made and effective July 21, 2026 by and between the City of Beaumont, a municipal corporation ("CITY"), and Kodiak Painting Inc., ("CONTRACTOR"), a California Corporation. In consideration of the mutual covenants and conditions set forth herein, the parties agree as follows:

I. SCOPE OF WORK
The CONTRACTOR shall perform within the time set forth in Article 2 of this Agreement and shall furnish all labor, materials, equipment, tools, utility services, and transportation and perform and complete all work required in connection with the City -Wide Facility Painting (hereinafter "Project"). CONTRACTOR's Bid, dated May 14, 2026, is attached hereto as Exhibit A and incorporated herein by this reference. The Scope of Work for the Project is set forth in the Invitation. In the event that any terms of the Bid are different from the Invitation for Bids, the Invitation for Bids shall control. Any additional terms in the Bid that purport to bind the City to any additional terms not contained in this Agreement and related attachments shall not be binding on the City.

By entering into this Agreement, CONTRACTOR acknowledges that there may be other contractors on the site whose work will be coordinated with that of its own. CONTRACTOR expressly warrants and agrees that it will cooperate with other contractors and will do nothing to delay, hinder, or interfere with the work of other separate contractors, the CITY, the Construction Manager, the Engineer, or utilities. CONTRACTOR also expressly agrees that, in the event its work is hindered, delayed, interfered with, or otherwise affected by a separate contractor, its sole remedy will be a direct action against the separate contractor. To the extent allowed by law, the CONTRACTOR will have no remedy, and hereby expressly waives any remedy against the CITY, the Construction Manager (if any), and the Engineer on account of delay, hindrance, interference or other events.

II. TIME FOR PROJECT COMPLETION
All of CONTRACTOR's work on the Project shall be completed within durations established for the individual activities. All work shall commence ten (10) calendar days after receiving a written Notice of Award from the CITY or Construction Manager, if a Construction Manager is employed by CITY on the Project. CONTRACTOR shall refer to the invitations for bids, and Project Plans and Specifications, all of which, as set forth below, are incorporated herein by reference, for contractual obligations regarding individual activity durations.

III. THE CONTRACT SUM

Page 1 of 13 ends

Page 2024 of 2226 ends

The CITY shall pay to the CONTRACTOR for the performance of this Agreement, subject to any additions and deductions provided in the Project documents, the sum of Seventy -Three Thousand Dollars and No Cents ($73,000.00).

IV. PROGRESS PAYMENTS
Based upon Applications for Payment submitted to the Engineer by the CONTRACTOR and Certificates for Payment issued by the Engineer, the CITY shall make progress payments on account of the Contract Sum to the CONTRACTOR as provided in the General Conditions, which are fully incorporated into this Agreement by this reference.

This Agreement is subject to the provisions of Article 1.7 (commencing at Section 20104.50) of Division 2, Part 3 of the Public Contract Code regarding prompt payment of contractors by local governments. Article 1.7 mandates certain procedures for the payment of undisputed and properly submitted payment requests within 30 days after receipt, for the review of payment requests, for notice to Contractor of improper payment requests, and provides for the payment of interest on progress payment requests which are not timely made in accordance with that Article. This Agreement hereby incorporates the provisions of Article 1.7 as though fully set forth herein.

V. INDEMNITY, DEFENSE AND HOLD HARMLESS AGREEMENT
CONTRACTOR shall indemnify, defend with legal counsel approved by CITY, and hold harmless CITY, its officers, officials, employees and volunteers from and against all liability, loss, damage, expense, cost (including without limitation reasonable legal counsel fees, expert fees and all other costs and fees of litigation) of every nature arising out of or in connection with CONTRACTOR's negligence, recklessness or willful misconduct in the performance of work hereunder or its failure to comply with any of its obligations contained in this Agreement, except such loss or damage which is caused by the sole or active negligence or willful misconduct of the CITY. Should conflict of interest principles preclude a single legal counsel from representing both CITY and CONTRACTOR, or should CITY otherwise find CONTRACTOR's legal counsel unacceptable, then CONTRACTOR shall reimburse the CITY its costs of defense, including without limitation reasonable legal counsels fees, expert fees and all other costs and fees of litigation. The CONTRACTOR shall promptly pay any final judgment rendered against the CITY (and its officers, officials, employees and volunteers) with respect to claims determined by a trier of fact to have been the result of the CONTRACTOR's negligent, reckless or wrongful performance. It is expressly understood and agreed that the foregoing provisions are intended to be as broad and inclusive as is permitted by the law of the State of California and will survive termination of this Agreement.

Page 2 of 13 ends

Page 2025 of 2226 ends

CONTRACTOR obligations under this section apply regardless of whether or not such claim, charge, damage, demand, action, proceeding, loss, stop notice, cost, expense, judgment, civil fine or penalty, or liability was caused in part or contributed to by an Indemnitee. However, without affecting the rights of CITY under any provision of this agreement, CONTRACTOR shall not be required to indemnify and hold harmless CITY for liability attributable to the active negligence of CITY, provided such active negligence is determined by agreement between the parties or by the findings of a court of competent jurisdiction. In instances where CITY is shown to have been actively negligent and where CITY active negligence accounts for only a percentage of the liability involved, the obligation of CONTRACTOR will be for that entire portion or percentage of liability not attributable to the active negligence of CITY.

VI. PREVAILING WAGES
A. Contractor shall comply with all applicable laws and regulations relating to prevailing wages. Wage rates for this Project shall be in accordance with the "General Wage Determination Made By the Director of Industrial Relations Pursuant To California Labor Code, Part 7, Chapter 1, Article 2, Sections 1770, 1773 and 1773.1", for Riverside County. Wage rates shall conform with those posted at Beaumont City Hall and the Project site.

B. The following Labor Code sections are hereby referenced and made a part of this Agreement:

1. Section 1775 - Penalty for Failure to Comply with Prevailing Wage Rates.

2. Section 1777.4 - Apprenticeship Requirements.

3. Section 1777.5 - Apprenticeship Requirements.

4. Section 1813 - Penalty for Failure to Pay Overtime.

5. Sections 1810 and 1811 - Working Hour Restrictions.

6. Section 1775 - Payroll Records.

7. Section 1773.8 - Travel and Subsistence Pay.

VII. RECORD AUDIT
In accordance with Government Code, Section 8546.7, records of both the CITY and the CONTRACTOR shall be subject to examination and audit by the Auditor General for a period of three (3) years after final payment.

VIII. FINAL PAYMENT
Final payment, constituting the entire unpaid balance of the Agreement Sum, shall be paid by the CITY to the CONTRACTOR no sooner than thirty-five (35) days after a Notice of Completion has been recorded, unless otherwise stipulated

Page 3 of 13 ends

Page 2026 of 2226 ends

in the Notice of Completion, provided the work has then been completed, the Agreement fully performed, and a final Certificate for Payment has been issued by the Engineer.

IX. CONTRACTOR'S FAILURE TO PROCURE COMPLETION OF PROJECT In the event CONTRACTOR fails to furnish tools, equipment, or labor in the necessary quantity or quality, or fails to prosecute the work or any part thereof contemplated by this Agreement in a diligent and workmanlike manner, and if the CONTRACTOR for a period of three (3) calendar days after receipt of written demand from CITY or its designated representative to do so, fails to furnish tools, equipment, or labor in the necessary quantity or quality, and to prosecute its work and all parts thereof in a diligent and workmanlike manner, or after commencing to do so within said three (3) calendar days, fails to continue to do so; then the CITY may exclude the CONTRACTOR from the premises, or any portion thereof, and take possession of said premises or any portion thereof, together with all material and equipment thereon, and may complete the work contemplated by this Agreement or any portion of said work, either by furnishing the tools, equipment, labor or material necessary, or by letting the unfinished portion of said work, or the portion taken over by the CITY to another contractor or by a combination of such methods. In any event, the procuring of the completion of said work, or the portion thereof taken over by the CITY, shall be a charge against the CONTRACTOR, and may be deducted from any money due or becoming due to CONTRACTOR from the CITY, or the CONTRACTOR shall pay the CITY the amount of said charge, or the portion thereof unsatisfied. The sureties, provided for under this Agreement shall become liable for payment should CONTRACTOR fail to pay in full any said cost incurred by the CITY.

X. INSURANCE
Prior to the beginning of and throughout the duration of the Project, CONTRACTOR and its subcontractors shall maintain insurance in conformance with the requirements set forth below. Attached hereto as Exhibit D are copies of Certificates of Insurance and the waiver of subrogation endorsement as required by Section 6.B.1. CONTRACTOR will use existing coverage to comply with these requirements. If that existing coverage does not meet the requirements set forth herein, CONTRACTOR agrees to amend, supplement or endorse the existing coverage to do so.

CONTRACTOR acknowledges that the insurance coverage and policy limits set forth in this section constitute the minimum amount of coverage required. Any insurance proceeds available to CONTRACTOR or its subcontractors in excess of the limits and coverage identified in this Agreement and which is applicable to a given loss, claim or demand, will be equally available to CITY.

A. Types of Insurance

Page 4 of 13 ends

Page 2027 of 2226 ends

Without limiting CONTRACTOR's indemnification of CITY, and prior to commencement of Work, CONTRACTOR shall obtain, provide and maintain at its own expense during the term of this Agreement, policies of insurance of the type and amounts described below and in a form satisfactory to CITY:

1. General liability insurance. CONTRACTOR shall maintain commercial general liability insurance with coverage at least as broad as Insurance Services Office form CG 00 01, in an amount not less than $1,000,000 per occurrence, $2,000,000 general aggregate, for bodily injury, personal injury, and property damage, and a $2,000,000 completed operations aggregate. The policy must include contractual liability that has not been amended. Any endorsement restricting standard ISO "insured contract" language will not be accepted.

2. Automobile liability insurance. CONTRACTOR shall maintain automobile insurance at least as broad as Insurance Services Office form CA 00 01 covering bodily injury and property damage for all activities of the CONTRACTOR arising out of or in connection with Work to be performed under this Agreement, including coverage for any owned, hired, non -owned or rented vehicles, in an amount not less than $1,000,000 combined single limit for each accident.

3. Umbrella or excess liability insurance. If CONTRACTOR is using umbrella coverage to meet part of its liability insurance requirements under Paragraph 1 of this Section, CONTRACTOR shall obtain and maintain an umbrella or excess liability insurance that will provide bodily injury, personal injury, completed operations and property damage liability coverage at least as broad as the primary coverages set forth above, including commercial general liability and employer's liability. Such policy or policies shall include the following terms and conditions:
• A drop down feature requiring the policy to respond in the event that any primary insurance that would otherwise have applied proves to be uncollectable in whole or in part for any reason; • Pay on behalf of wording as opposed to reimbursement; • Concurrency of effective dates with primary policies; • Policies shall "follow form" to the underlying primary policies; and
• Insureds under primary policies shall also be insureds under the umbrella or excess policies.

4. Workers' compensation insurance. CONTRACTOR shall maintain Workers' Compensation Insurance (Statutory Limits) and Employer's Liability Insurance (with limits of at least $1,000,000) for

Page 5 of 13 ends

Page 2028 of 2226 ends

CONTRACTOR's employees in accordance with the laws of the State of California, Section 3700 of the Labor Code. In addition, CONTRACTOR shall require each subcontractor to similarly maintain Workers' Compensation Insurance and Employer's Liability Insurance in accordance with the laws of the State of California, Section 3700 for all of the subcontractor's employees.

CONTRACTOR shall submit to CITY, along with the certificate of insurance, a Waiver of Subrogation endorsement in favor of CITY, its officers, agents, employees and volunteers.

5. Pollution liability insurance. Environmental Impairment Liability Insurance shall be written on a CONTRACTOR's Pollution Liability form or other form acceptable to CITY providing coverage for liability arising out of sudden, accidental and gradual pollution and remediation. The policy limit shall be no less than $1,000,000 dollars per claim and in the aggregate. All activities contemplated in this Agreement shall be specifically scheduled on the policy as "covered operations." The policy shall provide coverage for the hauling of waste from the project site to the final disposal location, including non -owned disposal sites.

Products/completed operations coverage shall extend a minimum of three (3) years after project completion. Coverage shall be included on behalf of the insured for covered claims arising out of the actions of independent contractors.

If the insured is using subcontractors, the Policy must include work performed "by or on behalf" of the insured. Policy shall contain no language that would invalidate or remove the insurer's duty to defend or indemnify for claims or suits expressly excluded from coverage. Policy shall specifically provide for a duty to defend on the part of the insurer. The CITY, its officials, officers, agents, and employees, shall be included as insureds under the policy.

6. Builder's risk insurance. Upon commencement of construction and with approval of CITY, CONTRACTOR shall obtain and maintain builder's risk insurance for the entire duration of the Project until only the CITY has an insurable interest. The Builder's Risk coverage shall include the coverages as specified below.

The named insureds shall be CONTRACTOR and CITY, including its officers, officials, employees, and agents. All Subcontractors (excluding those solely responsible for design Work) of any tier and suppliers shall be included as additional insureds as their interests may appear. CONTRACTOR shall not be required to maintain property insurance for any portion of the Project following transfer of control thereof to CITY. The policy shall contain a provision that all proceeds

Page 6 of 13 ends

Page 2029 of 2226 ends

from the builder's risk policy shall be made payable to the CITY. The CITY will act as a fiduciary for all other interests in the Project.

Policy shall be provided for replacement value on an "all risk" basis for the completed value of the project. There shall be no coinsurance penalty or provisional limit provision in any such policy. Policy must include: (1) coverage for any ensuing loss from faulty workmanship, Nonconforming Work, omission or deficiency in design or specifications; (2) coverage against machinery accidents and operational testing; (3) coverage for removal of debris, and insuring the buildings, structures, machinery, equipment, materials, facilities, fixtures and all other properties constituting a part of the Project; (4) Ordinance or law coverage for contingent rebuilding, demolition, and increased costs of construction; (5) transit coverage (unless insured by the supplier or receiving contractor), with sub -limits sufficient to insure the full replacement value of any key equipment item; (6) Ocean marine cargo coverage insuring any Project materials or supplies, if applicable; (7) coverage with sub -limits sufficient to insure the full replacement value of any property or equipment stored either on or off the Site or any staging area. Such insurance shall be on a form acceptable to CITY to ensure adequacy of terms and sublimits and shall be submitted to the CITY prior to commencement of construction.

B. Other provisions or requirements

1. Proof of insurance. CONTRACTOR shall provide certificates of insurance to CITY as evidence of the insurance coverage required herein, along with a waiver of subrogation endorsement for workers' compensation. Insurance certificates and endorsements must be approved by CITY's risk manager prior to commencement of performance. Current certification of insurance shall be kept on file with CITY at all times during the term of this contract. CITY reserves the right to require complete, certified copies of all required insurance policies, at any time.

2. Duration of coverage. CONTRACTOR shall procure and maintain for the duration of the contract insurance against claims for injuries to persons or damages to property, which may arise from or in connection with the performance of the Work hereunder by CONTRACTOR, his agents, representatives, employees or
subcontractors. CONTRACTOR must maintain general liability and umbrella or excess liability insurance for as long as there is a statutory exposure to completed operations claims. CITY and its officers, officials, employees, and agents shall continue as additional insureds under such policies.

Page 7 of 13 ends

Page 2030 of 2226 ends

3. Primary/noncontributing. Coverage provided by CONTRACTOR shall be primary and any insurance or self-insurance procured or maintained by CITY shall not be required to contribute with it. The limits of insurance required herein may be satisfied by a combination of primary and umbrella or excess insurance. Any umbrella or excess insurance shall contain or be endorsed to contain a provision that such coverage shall also apply on a primary and non-contributory basis for the benefit of CITY before the CITY's own insurance or self-insurance shall be called upon to protect it as a named insured.

4. CITY's rights of enforcement. In the event any policy of insurance required under this Agreement does not comply with these requirements or is canceled and not replaced, CITY has the right but not the duty to obtain the insurance it deems necessary and any premium paid by CITY will be promptly reimbursed by CONTRACTOR or CITY will withhold amounts sufficient to pay premium from CONTRACTOR payments. In the alternative, CITY may cancel this Agreement.

5. Acceptable insurers. All insurance policies shall be issued by an insurance company currently authorized by the Insurance Commissioner to transact business of insurance or is on the List of Approved Surplus Line Insurers in the State of California, with an assigned policyholders' Rating of A- (or higher) and Financial Size Category Class VII (or larger) in accordance with the latest edition of Best's Key Rating Guide, unless otherwise approved by the CITY's risk manager.

6. Waiver of subrogation. All insurance coverage maintained or procured pursuant to this agreement shall be endorsed to waive subrogation against CITY, its elected or appointed officers, agents, officials, employees and volunteers or shall specifically allow CONTRACTOR or others providing insurance evidence in compliance with these specifications to waive their right of recovery prior to a loss.

CONTRACTOR hereby waives its own right of recovery against CITY, and shall require similar written express waivers and insurance clauses from each of its subconsultants.

7. Enforcement of contract provisions (non estoppel).

CONTRACTOR acknowledges and agrees that any actual or alleged failure on the part of the CITY to inform CONTRACTOR of non- compliance with any requirement imposes no additional obligations on the CITY nor does it waive any rights hereunder.

8. Requirements not limiting. Requirements of specific coverage features or limits contained in this Section are not intended as a

Page 8 of 13 ends

Page 2031 of 2226 ends

limitation on coverage, limits or other requirements, or a waiver of any coverage normally provided by any insurance. Specific reference to a given coverage feature is for purposes of clarification only as it pertains to a given issue and is not intended by any party or insured to be all inclusive, or to the exclusion of other coverage, or a waiver of any type.

If the CONTRACTOR maintains higher limits than the minimums shown above, the CITY requires and shall be entitled to coverage for the higher limits maintained by the CONTRACTOR. Any available insurance proceeds in excess of the specified minimum limits of insurance and coverage shall be available to the CITY.

9. Notice of cancellation. CONTRACTOR agrees to oblige its insurance agent or broker and insurers to provide to CITY with a thirty (30) day notice of cancellation (except for nonpayment for which a ten (10) day notice is required) or nonrenewal of coverage for each required coverage.

10.Additional insured status. General liability policies shall provide or be endorsed to provide that CITY and its officers, officials, employees, agents, and volunteers shall be additional insureds under such policies. This provision shall also apply to any excess/umbrella liability policies.

11. Prohibition of undisclosed coverage limitations. None of the coverages required herein will be in compliance with these requirements if they include any limiting endorsement of any kind that has not been first submitted to CITY and approved of in writing.

12.Separation of insureds. A severability of interests provision must apply for all additional insureds ensuring that CONTRACTOR's insurance shall apply separately to each insured against whom claim is made or suit is brought, except with respect to the insurer's limits of liability. The policy(ies) shall not contain any cross -liability exclusions.

13. Pass through clause. CONTRACTOR agrees to ensure that its subconsultants, subcontractors, and any other party involved with the project who is brought onto or involved in the project by CONTRACTOR, provide the same minimum insurance coverage and endorsements required of CONTRACTOR. CONTRACTOR agrees to monitor and review all such coverage and assumes all responsibility for ensuring that such coverage is provided in conformity with the requirements of this section. CONTRACTOR agrees that upon request, all agreements with consultants, subcontractors, and others engaged in the project will be submitted to CITY for review.

Page 9 of 13 ends

Page 2032 of 2226 ends

14.CITY's right to revise requirements. The CITY reserves the right at any time during the term of the contract to change the amounts and types of insurance required by giving the CONTRACTOR a ninety (90) day advance written notice of such change. If such change results in substantial additional cost to the CONTRACTOR, the CITY and CONTRACTOR may renegotiate CONTRACTOR's compensation.

15.Self-insured retentions. Any self -insured retentions must be declared to and approved by CITY. CITY reserves the right to require that self - insured retentions be eliminated, lowered, or replaced by a deductible.

Self-insurance will not be considered to comply with these specifications unless approved by CITY.

16.Timely notice of claims. CONTRACTOR shall give CITY prompt and timely notice of claims made or suits instituted that arise out of or result from CONTRACTOR's performance under this Agreement, and that involve or may involve coverage under any of the required liability policies.

17.Additional insurance. CONTRACTOR shall also procure and maintain, at its own cost and expense, any additional kinds of insurance, which in its own judgment may be necessary for its proper protection and prosecution of the Work.

XI. CONTRACTOR'S LICENSE
CONTRACTOR must possess at the time of commencing work and throughout the Project duration, a Contractor's License, issued by the State of California, which is current and in good standing. CONTRACTOR shall ensure that any subcontractor working on the Project possesses at the time of commencing work and throughout the Project duration, a Contractor's License, issued by the State of California, which is current and in good standing.

XII. REGISTRATION REQUIREMENTS
A. Pursuant to Section 1771.1(a) of the Labor Code:
"A contractor or subcontractor shall not be qualified to bid on, be listed in a bid proposal, subject to the requirements of Section 4104 of the Public Contract Code, or engage in the performance of any contract for public work, as defined in this chapter, unless currently registered and qualified to perform public work pursuant to Section 1725.5. It is not a violation of this section for an unregistered contractor to submit a bid that is authorized by Section 7029.1 of the Business and Professions Code or by Section 10164 or 20103.5 of the Public Contract

Page 10 of 13 ends

Page 2033 of 2226 ends

Code, provided the contractor is registered to perform public work pursuant to Section 1725.5 at the time the contract is awarded."
B. CONTRACTOR must be registered with the Department of Industrial Relations (DIR) of the State of California in order to be eligible to work on public works projects. CONTRACTOR must ensure registration with the DIR that is active and in good standing.

C. No contractor or subcontractor may be listed on a bid proposal for a public works project unless registered with the Department of Industrial Relations pursuant to Labor Code section 1725.5 [with limited exceptions from this requirement for bid purposes only under Labor Code section 1771.1(a)].

No contractor or subcontractor may be awarded a contract for public work on a public works project (awarded on or after April 1, 2015) unless registered with the Department of Industrial Relations pursuant to Labor Code section 1725.5.

This project is subject to compliance monitoring and enforcement by the Department of Industrial Relations.

D. The CONTRACTOR is not subject to public works requirements (including registration with the DIR) if the public works project is under $1,000, unless the CITY knows that the same CONTRACTOR will be awarded total project costs in excess of $1,000 for a given year.

XIII. CORPORATION IN GOOD STANDING
If CONTRACTOR is a corporation, the undersigned hereby represents and warrants that the corporation is duly incorporated and in good standing in the State of California, and that David Van Dyke whose title is President is authorized to act for and bind the corporation.

XIV. PROVISIONS REQUIRED BY LAW
Each and every provision of law and clause required by law to be inserted in this Agreement shall be deemed to be inserted herein and the Agreement shall be read and enforced as though it were included herein, and if through mistake or otherwise any such provision is not inserted, or is not currently inserted, then upon application of either party the Agreement shall forthwith be physically amended to make such insertion or correction.

XV. SUBSURFACE HAZARDOUS MATERIALS
A. In the event trenches or other excavations extend deeper than four (4) feet below the surface, the CONTRACTOR shall promptly, and before the following conditions are disturbed, notify the CITY in writing of any:

Page 11 of 13 ends

Page 2034 of 2226 ends

1. Material that the CONTRACTOR believes may be material that is hazardous waste, as defined in Section 25117 of the Health and Safety Code that is required to be removed to a Class I, Class II or Class I I I disposal site in accordance with the provisions of existing law.

2. Subsurface or latent physical conditions at the site differing from those indicated.

3. Unknown physical conditions at the site of any unusual nature, different materially from those ordinarily encountered and generally recognized as inherent in the Work or the character provided for in the CONTRACT.

B. Upon receipt of said notification the CITY will investigate the conditions, and if it finds that the conditions do materially so differ, or do involve hazardous waste, and cause a decrease or increase in the CONTRACTOR's cost of or the time required for performance of any part of the work, the CITY will issue a change order under the procedures described in the General Conditions.

C. In the event that a dispute arises between the CITY and the CONTRACTOR whether the conditions materially differ, or involve hazardous waste or cause a decrease or increase in the CONTRACTOR's cost of or time required for performance of any part of the work, the CONTRACTOR shall not be excused from any scheduled completion date provided for by the Agreement, but shall proceed with all work to be performed under the Agreement. The CONTRACTOR shall retain any and all rights provided either by Agreement or by law which pertain to the resolution of disputes and protests between the contracting parties.

XVI. COMPONENT PARTS OF THE CONTRACT
This Agreement entered into consists of the following CONTRACT DOCUMENTS, all of which are component parts of the Agreement as if herein set out in full or attached hereto:
❑Notice Inviting Bids
❑Scope of Work Summary
❑Information for Bidders
❑Bid Form
❑Non -Collusion Affidavit
❑Site Visit Certification
❑Faithful Performance Bond
❑Labor and Materials Payment
Bond
❑General and Supplemental
Conditions
❑Special Conditions
❑Project Construction Schedule
❑Proposed Subcontractors
❑ Bid Bond
❑Information Required of Bidder
❑Construction Services Agreement
❑Certificate Regarding Worker's
❑Compensation

Page 12 of 13 ends

Page 2035 of 2226 ends

❑ Drug -free Workplace Certification
❑ Plans and Specifications
Addenda
❑ Drawings
Change Orders
▪ Shop Drawing Transmittals
▪ Contractor's Certificate Regarding
❑Non -Asbestos Containing
Materials
All of the above -named CONTRACT DOCUMENTS are intended to be complementary. Work required by one of the above -named CONTRACT DOCUMENTS and not by others shall be done as if required by all.

XVII. ENTIRE CONTRACT
This Agreement constitutes the entire contract of the parties. No other agreements or contracts, whether oral or written, pertaining to the work to be performed, exists between the parties. This Agreement can be modified only by an amendment in writing, signed by both parties.
[Signatures on following page.]

Page 13 of 13 ends

Page 2036 of 2226 ends

SIGNATURE PAGE TO

CITY OF BEAUMONT

PUBLIC WORKS AGREEMENT
CITY: CONTRACTOR:

CITY OF BEAUMONT KODIAK PAINTING, INC.

By:

Print Name: Jason Morton
Chris Boatman, City Manager Title: President

Page 20 ends

CITY OF BEAUMONT

PUBLIC WORKS AGREEMENT
EXHIBIT "A"
CITY'S FEBRUARY 9, 2023

INVITATION FOR BIDS
15

Page 2038 of 2226 ends

BEAUMONT

CALIFORNIA
INVITATION FOR BID:

City -Wide Facility Painting

CRITICAL BID DATES, TIMES, & LOCATIONS
Bid Published: April 28, 2026
Mandatory Pre -Bid Meeting:

Questions Due Date:

Bids Must Be Received By:

Place Of Bid Submission:

Place of Bid Bond Submission:

Bid Opening Date:

Bid Opening Location:

May 12, 2026 @ 9:00 A.M.
at 514 California Ave, Beaumont CA
May 19, 2026 @ 11:00 A.M.

May 28, 2026@ 11:00 A.M.
https://vendors.planetbids.com/portal/66785/bo/bo-detail/141388 Beaumont City Hall, Attn: Purchasing,
550 E Sixth Street, Beaumont, CA 92223
May 28, 2026 @ 11:15 A.M
https://vendors.planetbids.com/portal/66785/bo/bo-detail/141388 CONTACT:

Barbara Mason
Purchasing Manager
[email protected]
IFB AVAILABLE:
https://vendors.planetbids.com/portal/66785/bo/bo-detail/141388 or https://www.beaumontca.gov/949/Bids-and- RFPs

Page 2039 of 2226 ends

City of Beaumont Invitation
for Bid
-CALIFORNIA-
City-wide Facility
Painting Services

CITY OF BEAUMONT

CALIFORNIA
Community Services Department
FOR:

City-wide Facility Painting

Page 2040 of 2226 ends

City of Beaumont Invitation
for Bid BEAUMONT
-CALIFORNIA-
City-wide Facility
Painting Services
Table of Contents
NOTICE INVITING BIDS 4
INSTRUCTIONS TO BIDDERS 6
BID FORM 13
BASE BID 14
BID SCHEDULE 14
BID CERTIFICATION 16
CONTRACTOR'S CERTIFICATE REGARDING WORKERS' COMPENSATION 17 BID BOND 18
PAYMENT BOND 19
DESIGNATION OF SUBCONTRACTORS 25
INFORMATION REQUIRED OF BIDDERS 28
NON -COLLUSION AFFIDAVIT 36

APPENDIX A - PUBLIC WORKS AGREEMENT
APPENDIX B - Project Scope and Specifications
APPENDIX C — Police Station Images
APPENDIX D — Police Station Annex Images
APPENDIX E — Albert Chatigny Recreation Center Images

Page 2041 of 2226 ends

City of Beaumont Invitation
for Bid
-CALIFORNIA-
City-wide Facility
Painting Services

NOTICE INVITING BIDS
The City of Beaumont, Community Services Department ("City") is soliciting bids for:

CITY WIDE FACILITY PAINTING
BID SCHEDULES:

Bid Published:

Pre -Bid Meeting:

April 28, 2026
May 12, 2026 @ 9:00 A.M.
at 514 California Ave., Beaumont, CA 92223
Questions Due By: May 19, 2026 @ 11:00 A.M.

Bid must be received by: May 28, 2026 @ 11:00 A.M.550 E. Sixth Street Beaumont, CA 92223
Place of Bid Submission:

Bid Bond Submission Location"
Bid Opening Date:

ANTICIPATED CONTRACT AWARD:

ANTICIPATED NOTICE TO PROCEED:
https://vendors.planetbids.com/portal/66785/bo/b
o-detail/141 388
550 E. Sixth Street (City Hall)
Beaumont, CA 92223
May 28, 2026 @ 11:15 A.M
July 21, 2026
July 28, 2026
Bids received after February 26, 2025, at 11:OOam will not be accepted. Bids shall be valid for 90 calendar days after the Bid opening date. Bids must be submitted on the City's Bid Forms. Bids must be prepared on the approved Bid forms and in the manner prescribed in the Instructions to Bidders. Bids must be submitted with the following subject:

BID FOR CITY WIDE FACILITY PAINTING
LOCATION OF WORK:

The work is to be completed at four locations.

1. 660 Orange Avenue, Beaumont CA (Police Station)

2. 1588 E 8t" St, Beaumont CA (Police Station Annex)

3. 1310 Oak Valley Parkway, Beaumont CA (Albert Chatigny Community Recreation Center)
4

Page 2042 of 2226 ends

City of Beaumont Invitation
for Bid
-CALIFORNIA-
City-wide Facility
Painting Services
DESCRIPTION OF WORK:

The proposed work shall be performed in accordance with the Contract and the scope outlined in this Invitation for Bids.

The Project includes, without limitation, furnishing all necessary labor, materials, equipment and other incidental and appurtenant Work necessary to satisfactorily complete the Project, consists of and includes the exterior painting of three facilities and interior painting of one facility. The scope of work is organized by facility and includes detailed requirements for surface preparation, priming, and painting. The Project is more specifically described in the Contract Documents. This Work will be performed in strict conformance with the Contract Documents, permits from regulatory agencies with jurisdiction, and applicable regulations. The quantity of Work to be performed and materials to be furnished are approximations only, being given as a basis for the comparison of Bids. Actual quantities of Work to be performed may vary at the discretion of the Community Services Director.

CONTRACT LENGTH:

The work for this contract shall not exceed 75 calendar days. Contract time shall commence upon issuance of the Notice to Proceed from the City. If the work is not completed as stated in the Contract Documents, there will be liquidated damages in a sum of $500 per calendar day. This contract shall be in effect until completion and acceptance of all work.

PRE -BID MEETING AND SITE VISIT:

A mandatory pre -bid meeting will be held at the time and place stated in the Bid Schedule.

No allowances for cost adjustments will be made if a Bidder fails to adequately examine the Project site before submitting a Bid.

AWARD OF CONTRACT:

The City shall award the Contract for the Project to the lowest responsive, responsible Bidder as determined from the base Bid. The City reserves the right to reject any or all Bids or to waive any irregularities or informalities in any Bids or in the Bid process.

CONTRACT DOCUMENTS AND SPECIFICATION:

Copies of the Contract Documents and Specifications are available for inspection at no cost to the Bidder at City Hall. The documents can also be downloaded from the City's Website: https://beaumontca.gov/949/Bids-and-RFPs and https://vendors.planetbids.com/portal/66785/bo/bo-detail/141388 and reviewed at no cost.

BID AND BIDDER:

A Bid Bond in favor of the City in an amount not less than ten percent (10%) of the submitted Total Bid Price is required for this project. Bid Bonds must be delivered to Beaumont City Hall, Attn: Purchasing, 550 E Sixth Street, Beaumont, CA 92223 on or before the bid due date.

Each Bid shall be accompanied by the security referred to in the Contract Documents, the non -collusion affidavit, the list of proposed subcontractors, and all additional documentation required by the Instructions to Bidders.
5

Page 2043 of 2226 ends

City of Beaumont Invitation
for Bid
-CALIFORNIA-
City-wide Facility
Painting Services
Each bid shall be accompanied by the security referred to in the Contract Documents, the non -collusion affidavit, the list of proposed subcontractors, and all additional documentation required by the Instructions to Bidders.

The successful bidder will be required to furnish the City with a Performance Bond equal to 100% of the successful bid, and a Payment (Labor and Materials) Bond equal to 100% of the successful bid, prior to execution of the Contract. All bonds are to be secured from a surety that meets all of the State of California bonding requirements, as defined in Code of Civil Procedure Section 995.120, and is admitted by the State of California.

Each bidder and their subcontractors shall be a licensed contractor pursuant to the Business and Professions Code and shall be licensed in the following appropriate classification(s) of contractor's license(s) for the work bid upon, and must maintain the license(s) throughout the duration of the Contract. The bidder shall have the following license:
• California Class "C-33" license
6

Page 2044 of 2226 ends

City of Beaumont Invitation
for Bid
-CALIFORNIA-

INSTRUCTIONS TO BIDDERS
City-wide Facility
Painting Services
AVAILABILITY OF CONTRACT DOCUMENTS:

Bids must be submitted electronically on the City's electronic bid platform Planetbids on the Bid Forms which are a part of the Bid Package for the Project.

EXAMINATION OF CONTRACT DOCUMENTS:

The City has made copies of the Contract Documents available, as indicated above.

Bidders shall be solely responsible for examining the Project Site and the Contract Documents, including any Addenda issued during the bidding period, and for informing itself with respect to local labor availability, means of transportation, necessity for security, laws and codes, local permit requirements, wage scales, local tax structure, contractors' licensing requirements, availability of required insurance, and other factors that could affect the Work. Bidders are responsible for consulting the standards referenced in the Contract. Failure of Bidder to examine and inform itself shall be at its sole risk, and no relief for error or omission will be given except as required under State law.

INTERPRETATION OF CONTRACT DOCUMENTS
Discrepancies in, and/or omissions from the Plans, Specifications or other Contract Documents or questions as to their meaning shall be submitted as a question on the Planetbids bid platform for an interpretation or correction to the City by the deadline stated herein. Any interpretation of the Contract Documents will be made only by written addenda through the Planetbids platform. The City will not be responsible for any explanations or interpretations provided in any other manner. No person is authorized to make any oral interpretation of any provision in the Contract Documents to any bidder, and no bidder should rely on any such oral interpretation. Bids shall include complete compensation for all items that are noted in the Contract Documents as the responsibility of the Contractor.

INSPECTION OF SITE:

Each prospective bidder is responsible for fully acquainting itself with the conditions of the Project Site (which may include more than one site), as well as those relating to the construction and labor of the Project, to fully understand the facilities, difficulties and restrictions which may impact the cost or effort required to complete the Project.

ADDENDA:

The City reserves the right to revise the Contract Documents prior to the bid opening date.

Revisions, if any, shall be made by written Addenda posted on Planetbids website. All addenda issued by the City shall be included in the bid and made part of the Contract Documents. Pursuant to Public Contract Code Section 4104.5, if the City issues an Addendum which includes material changes to the Project less than 72 hours prior to the deadline for submission of bids, the City will extend the deadline for submission of bids.

The City may determine, in its sole discretion, whether an Addendum warrants postponement of the bid submission date. Copies of Addenda will only be furnished using vendors. clanetbids.com.
7

Page 2045 of 2226 ends

City of Beaumont Invitation
for Bid

BEAUMONT
-CALIFORNIA-
Please Note: Bidders are responsible for ensuring that they have received any and all Addenda. To this end, each bidder should contact the Director of Community Services to verify that he has received all Addenda issued, if any, prior to the bid opening.

City-wide Facility
Painting Services

ALTERNATE BIDS
If alternate bid items are called for in the Contract Documents, the lowest bid will be determined on the basis of the base bid only. However, the City may choose to award the contract on the basis of the base bid alone or the base bid and any alternate or combination of alternates. The time required for completion of the alternate bid items has been factored into the Contract duration and no additional Contract time will be awarded for any of the alternate bid items. The City may elect to include one or more of the alternate bid items, or to otherwise remove certain work from the Project scope of work, accordingly each Bidder must ensure that each bid item contains a proportionate share of profit, overhead and other costs or expenses which will be incurred by the Bidder.

COMPLETION OF BID FORMS
Bids shall only be prepared using copies of the Bid Forms which are included in the Contract Documents. The use of substitute bid forms other than clear and correct photocopies of those provided by the City will not be permitted. Bids shall be executed by an authorized signatory as described in these Instructions to Bidders. In addition, Bidders shall fill in all blank spaces (including inserting "N/A" where applicable) and initial all interlineations, alterations, or erasures to the Bid Forms. Bidders shall neither delete, modify, nor supplement the printed matter on the Bid Forms nor make substitutions thereon. Deviations in the bid form may result in the bid being deemed non- responsive.

MODIFICATIONS OF BIDS:

Each Bidder shall submit its Bid in strict conformity with the requirements of the Contract Documents. Unauthorized additions, modifications, revisions, conditions, limitations, exclusions or provisions attached to a Bid may render it non -responsive and may cause its rejection. Bidders shall neither delete, modify, nor supplement the printed matter on the Bid Forms, nor make substitutions thereon. Oral, telephonic and electronic modifications will not be considered, unless the Notice Inviting Bids authorizes the submission of electronic bids and modifications thereto and such modifications are made in accordance with the Notice Inviting Bids.

DESIGNATION OF SUBCONTRACTORS:

Pursuant to the funding regulation, the Bidders must designate the name and location of each subcontractor who will perform work or render services in an amount in excess of one-half of 1 percent of the prime contractor's total bid as well as the portion of work each such subcontractor will perform on the form provided herein by the City. No additional time will be provided to bidders to submit any of the requested information in the Designation of Subcontractor form.

LICENSING REQUIREMENTS:

Pursuant to Section 7028.15 of the Business and Professions Code and Section 3300 of 8

Page 2046 of 2226 ends

City of Beaumont Invitation
for Bid
-CALIFORNIA-
City-wide Facility
Painting Services
the Public Contract Code, all bidders must possess proper licenses for performance of this Contract. Subcontractors must possess the appropriate licenses for each specialty subcontracted. Pursuant to Section 7028.5 of the Business and Professions Code, the City shall consider any bid submitted by a contractor not currently licensed in accordance with state law and pursuant to the requirements found in the Contract Documents to be nonresponsive, and the City shall reject the Bid. The City shall have the right to request, and Bidders shall provide within five (5) calendar days, evidence satisfactory to the City of all valid license(s) currently held by that Bidder and each of the Bidder's subcontractors, before awarding the Contract. Please also note that, pursuant to Public Contract Code Section 20676, sellers of "mined material" must be on an approved list of sellers published pursuant to Public Resources Code Section 2717(b) in order to supply mined material for this Contract.

REGISTRATION WITH THE DEPARTMENT OF INDUSTRIAL RELATIONS. In accordance with Labor Code Sections 1725.5 and 1771.1, no contractor or subcontractor shall be qualified to bid on, be listed in a bid proposal, subject to the requirements of Section 4104 of the Public Contract Code, or engage in the performance of any contract for public work, unless currently registered Bid Package, City-wide Facility Painting Project, and qualified to perform public work pursuant to Section 1725.5 [with limited exceptions for bid purposes only under Labor Code Section 1771.1(a)] PREVAILING WAGES. In accordance with Labor Code Section 1770 et seq., the Project is a "public work." The selected Bidder (Contractor) and any Subcontractors shall pay wages in accordance with the determination of the Director of the Department of Industrial Relations ("DIR") regarding the prevailing rate of per diem wages. Copies of those rates are on file with the Director of Public Works and are available to any interested party upon request. The Contractor shall post a copy of the DIR's determination of the prevailing rate of per diem wages at each job site. This Project is subject to compliance monitoring and enforcement by the DIR.

LICENSES. Each Bidder shall possess a valid Class C-33 Contractor's license issued by the California State Contractors License Board at the time of the Bid submission, unless this Project has any federal funding, in which case the successful Bidder must possess such a license at the time of Contract award. The successful Contractor must also possess a current City business license.

RETENTION SUBSTITUTION. Five percent (5%) of any progress payment will be withheld as retention. In accordance with Public Contract Code Section 22300, and at the request and expense of the Contractor, securities equivalent to the amount withheld may be deposited with the City or with a State or federally chartered bank as escrow agent, which shall then pay such moneys to the Contractor. Upon satisfactory completion of the Project, the securities shall be Bid Package, City Wide Facility Painting Project. Alternatively, the Contractor may request that the City make payments of earned retentions directly to an escrow agent at the Contractor's expense. No such substitutions shall be accepted until all related documents are approved by the City Attorney.

SIGNING OF BIDS:

All Bids submitted shall be executed by the Bidder or its authorized representative.

Bidders may be asked to provide evidence in the form of an authenticated resolution of its Board of Directors or a Power of Attorney evidencing the capacity of the person signing the Bid to bind the Bidder to each Bid and to any Contract arising therefrom. If a Bidder 9

Page 2047 of 2226 ends

City of Beaumont Invitation
for Bid
-CALIFORNIA-
City-wide Facility
Painting Services
is a joint venture or partnership, it may be asked to submit an authenticated Power of Attorney executed by each joint venturer or partner appointing and designating one of the joint venturers or partners as a management sponsor to execute the Bid on behalf of Bidder. Only that joint venturer or partner shall execute the Bid. The Power of Attorney shall also: (1) authorize that particular joint venturer or partner to act for and bind Bidder in all matters relating to the Bid; and (2) provide that each venturer or partner shall jointly and severally liable for any and all of the duties and obligations of Bidder assumed under the Bid and under any Contract arising therefrom. The Bid shall be executed by the designated joint venturer or partner on behalf of the joint venture or partnership in its legal name.

BID GUARANTEE (BOND):

Each bid shall be accompanied by: (a) cash; (b) a certified check made payable to the City; (c) a cashier's check made payable to the City; or (d) a bid bond payable to the City executed by the bidder as principal and surety as obligor in an amount not less than 10% of the maximum amount of the bid. Personal sureties and unregistered surety companies are unacceptable. The surety insurer shall be California admitted surety insurer, as defined in Code of Civil Procedure Section 995.120. The cash, check or bid bond shall be given as a guarantee that the bidder shall execute the Contract if it be awarded to the bidder, shall provide the payment and performance bonds and insurance certificates and endorsements as required herein within ten (10) calendar days after notification of the award of the Contract to the bidder. Failure to provide the required documents may result in forfeiture of the bidder's bid deposit or bond to the City and the City may award the Contract to the next lowest responsive, responsible bidder, or may call for new bids.

SUBMISSION OF BIDS:

Once the Bid and supporting documents have been completed and signed as set forth herein, and uploaded to Planetbids. No oral or telephonic bids will be considered. No forms transmitted via facsimile, or any other electronic means will be considered unless specifically authorized by City as provided herein.

DELIVERY AND OPENING OF BIDS
Bids Bids will be received by the City via Planetbids as denoted in the Notice Inviting Bids up to the date and time shown therein. It is the Bidder's sole responsibility to ensure that its Bid is received as specified. Bids may be submitted earlier than the dates(s) and time(s) indicated.

Bids will be released electronically at the date and time stated in the Notice Inviting Bids The City may in its sole discretion, elect to postpone the opening of the submitted Bids.

City reserves the right to reject any or all Bids and to waive any informality or irregularity in any Bid. In the event of a discrepancy between the written amount of the Bid Price and the numerical amount of the Bid Price, the written amount shall govern.

WITHDRAWAL OF BID:

Prior to bid opening, a Bid may be withdrawn by the Bidder only by means of a written request signed by the Bidder or its properly authorized representative.

BASIS OF AWARD; BALANCED BIDS:
10

Page 2048 of 2226 ends

City of Beaumont Invitation
for Bid BEAUMONT
-CALIFORNIA-
City-wide Facility
Painting Services
The City shall award the Contract to the lowest responsive, responsible Bidder submitting a responsive Bid. The City may reject any Bid which, in its opinion when compared to other bids received or to the City's internal estimates, does not accurately reflect the cost to perform the Work. The City may reject as non -responsive any bid which unevenly weights or allocates costs, including but not limited to overhead and profit to one or more particular bid items.

DISQUALIFICATION OF BIDDERS; INTEREST IN MORE THAN ONE BID:

No bidder shall be allowed to make, submit or be interested in more than one bid.

However, a person, firm, corporation or other entity that has submitted a subBid to a bidder, or that has quoted prices of materials to a bidder, is not thereby disqualified from submitting a subBid or quoting prices to other bidders submitting a bid to the City. No person, firm, corporation, or other entity may submit subBid to a bidder, or quote prices of materials to a bidder, when also submitting a prime bid on the same Project.

INSURANCE REQUIREMENTS:

The successful bidder shall procure the insurance in the form and in the amount specified in the Contract Documents.

AWARD PROCESS:

Once all Bids are opened and reviewed to determine the lowest responsive and responsible Bidder, the City Council may award the contract. The apparent successful Bidder should begin to prepare the following documents: (1) the Performance Bond; (2) the Payment (Labor and Materials) Bond; and (3) the required insurance certificates and endorsements. Once the City notifies the Bidder of the award, the Bidder will have ten (10) consecutive calendar days from the date of this notification to execute the Contract and supply the City with all of the required documents and certifications. Regardless whether the Bidder supplies the required documents and certifications in a timely manner, the Contract time will begin to run ten (10) calendar days from the date of the notification.

Once the City receives all of the properly drafted and executed documents and certifications from the Bidder, the City shall issue a Notice to Proceed to that Bidder.

FILING OF BID PROTESTS
Bidders may file a "protest" of a Bid with the City Engineer. In order for a Bidder's protest to be considered valid, the protest must:
• Be filed in writing within five (5) calendar days after the bid opening date; • Clearly identify the specific irregularity or accusation; • Clearly identify the specific City staff determination or recommendation being protested;
• Specify, in detail, the grounds of the protest and the facts supporting the protest; and
• Include all relevant, supporting documentation with the protest at time of filing.

If the protest does not comply with each of these requirements, it will be rejected as invalid. If the protest is valid, the City Engineer, or other designated City staff member, shall review the basis of the protest and all relevant information. The City Engineer will 11

Page 2049 of 2226 ends

City of Beaumont Invitation
for Bid BEAUMONT
-CALIFORNIA_provide a written decision to the protestor. The protestor may then appeal the decision of the City Engineer to the City Manager.

City-wide Facility
Painting Services
WORKERS COMPENSATION:

Each bidder shall submit the Contractor's Certificate Regarding Workers' Compensation form.

SUBSTITUTION OF SECURITY:

The Contract Documents call for monthly progress payments based upon the percentage of the work completed. The City will retain five percent (5%) of each progress payment as provided by the Contract Documents. At the request and expense of the successful Bidder, the City will substitute securities for the amount so retained in accordance with Public Contract Code Section 22300.

PREVAILING WAGES:

Pursuant to Section 1773 of the Labor Code, the general prevailing wage rates, including the per diem wages applicable to the work, and for holiday and overtime work, including employer payments for health and welfare, pension, vacation, and similar purposes, in the County of Riverside in which the work is to be done, have been determined by the Director of the Department of Industrial Relations, State of California. These wages are set forth in the General Prevailing Wage Rates for this project, available from the California Department of Industrial Relations' Internet web site at www.dir.ca.gov . Future effective prevailing wage rates which have been predetermined and are on file with the California Department of Industrial Relations, are referenced but not printed in the general prevailing wage rates. Pursuant to SB 854, which amended the Prevailing Wage Laws, this Contract is subject to compliance monitoring and enforcement by the DIR. Beginning March 1, 2015, with very limited exceptions, no contractor or subcontractor may be listed on a bid Bid for this Contract unless registered with the DIR pursuant to Labor Code section 1725.5. Beginning April 1, 2015, no contractor or subcontractor may be awarded this Contract unless registered with the DIR pursuant to Labor Code section 1725.5. The DIR registration number for each contractor and subcontractor must be identified on the bid Bid - failure to identify this number could result in the bid being rejected as non- responsive. It is each bidder's responsibility to ensure that they have fully complied with SB 854. The City will report all necessary contracts to the DIR as required by the Prevailing Wage Laws.

DEPARMENT OF CONTRACTORS AND SUBCONTRACTORS:

In accordance with the provisions of the Labor Code, contractors or subcontractors may not perform work on a public works project with a subcontractor who is ineligible to perform work on a public project pursuant to Section 1777.1 or Section 1777.7 of the Labor Code. Any contract on a public works project entered between a contractor and a debarred subcontractor is void as a matter of law. A debarred subcontractor may not receive any public money for performing work as a subcontractor on a public works contract. Any public money that is paid to a debarred subcontractor by the Contractor for the Project shall be returned to the City. The Contractor shall be responsible for the payment of wages to workers of a debarred subcontractor who has been allowed to work on the Project.
12

Page 2050 of 2226 ends

City of Beaumont Invitation
for Bid

BEAUMONT
-CALIFORNIA-
City-wide Facility
Painting Services
PERFORMANCE AND PAYMENT BOND REQUIREMENTS:

Within the time specified in the Contract Documents, the Bidder to whom a Contract is awarded shall deliver to the City four identical counterparts of the Performance Bond and Payment (Labor and Materials) Bond in the form supplied by the City and included in the Contract Documents. Failure to do so may, in the sole discretion of City, result in the forfeiture of the Bid Guarantee. The surety supplying the bond must be an admitted surety insurer, as defined in Code of Civil Procedure Section 995.120, authorized to do business as such in the State of California and satisfactory to the City. The Performance Bond and the Payment (Labor and Materials) Bond shall be for one hundred percent (100%) of the Total Bid Price.

REQUEST FOR SUBSTITUTIONS
The successful bidder shall comply with the substitution request provisions set forth in the Special Conditions, including any deadlines for substitution requests which may occur prior to the bid opening date.

SALES AND OTHER APPLICABLE TAXES, PERMITS, LICENSES AND FEES Contractor and its subcontractors performing work under this Contract will be required to pay California sales tax and other applicable taxes, and to pay for permits, licenses and fees required by the agencies with authority in the jurisdiction in which the work will be located, unless otherwise expressly provided by the Contract Documents.

EXECUTION OF CONTRACT
As required herein the Bidder to whom an award is made shall execute the Contract in the amount determined by the Contract Documents. The City may require appropriate evidence that the persons executing the Contract are duly empowered to do so.

END OF INSTRUCTIONS TO BIDDERS
13

Page 2051 of 2226 ends

City of Beaumont Invitation
for Bid

BEAUMONT
-CALIFORNIA-

BID FORM
NAME OF BIDDER:

City-wide Facility
Painting Services
The undersigned, hereby declare that we have carefully examined the location of the proposed Work, and have read and examined the Contract Documents, including all plans, specifications, and all addenda, if any, for the following Project:

City-wide Facility Painting
We hereby propose to furnish all labor, materials, equipment, tools, transportation, and services, and to discharge all duties and obligations necessary and required to perform and complete the Project for the following BASE BID TOTAL BID PRICE:

BASE
BID

BASE BID PRICE
(IN WRITTEN FORM)

BID PRICE
(IN NUMBERS)
Base Bid:

TOTAL

BID PRICE
In case of discrepancy between the written price and the numerical price, the written price shall prevail.
14

Page 2052 of 2226 ends

City of Beaumont Invitation
for Bid

BEAUMONT
-CALIFORNIA-

BASE BID

BID SCHEDULE
City-wide Facility Painting
City-wide Facility
Painting Services
ITEM
NO.

DESCRIPTION OF ITEMS
EST.

QUANTITY/UN IT

TOTAL COST
(FIGURES)
1 Police Station Exterior Paint
1 Lump
Sum
2 Police Station Annex Exterior Paint
1 Lump
Sum
3 Albert Chatigny Recreation Center
Exterior Paint
1 Lump
Sum
Total Cost
15

Page 2053 of 2226 ends

City of Beaumont Invitation
for Bid
-CALIFORNIA-
City-wide Facility
Painting Services
Items include references to specification sections where applicable. Contractor shall verify section and all specifications for bid item. Listed items and references are not intended to provide a complete list of all work included. All specifications and contract documents shall be considered when bidding.

In case of discrepancy between the unit price and the item cost set forth for a unit basis item, the unit price shall prevail and, shall be utilized as the basis for determining the lowest responsive, responsible bidder. However, if the amount set forth as a unit price is ambiguous, unintelligible or uncertain for any cause, or is omitted, or is the same amount as the entry in the "Item Cost" column, then the amount set forth in the "Item Cost" column for the item shall prevail and shall be divided by the estimated quantity for the item and the price thus obtained shall be the unit price. Final payment shall be determined by the Engineer from measured quantities of work performed based upon the unit price.

In case of discrepancy between the written price and the numerical price, the written price shall prevail.
16

Page 2054 of 2226 ends

City of Beaumont Invitation
for Bid

BEAUMONT
-CALIFORNIA-

BID CERTIFICATION
City-wide Facility Painting
City-wide Facility
Painting Services
Bidder certifies that it is licensed in accordance with the law providing for the registration of Contractors,
License No.

Expiration Date
Class of license
If the bidder is a joint venture, each member of the joint venture must include the above information.

The undersigned acknowledges receipt, understanding and full consideration of the following addenda to the Contract Documents:

1. Addenda No. thru

2. Attached is the required bid security in the amount of not less than 10% of the Total Bid Price.

3. Attached is the fully executed Non -Collusion Affidavit form.

4. Attached is the completed Designation of Subcontractors form.

5. Attached is the completed Bidder Information Form.

6. Attached is the completed Contractor's Certificate Regarding Workers' Compensation form.

Bidder acknowledges and understands that, pursuant to Public Contract Code Section 20676, sellers of "mined material" must be on an approved list of sellers published pursuant to Public Resources Code Section 2717(b) in order to supply mined material for this Contract.

I hereby certify under penalty of perjury under the laws of the State of California, that all of the information submitted in connection with this Bid and all of the representations made herein are true and correct.

Name of Bidder
Signature
Name and Title
Dated
17

Page 2055 of 2226 ends

City of Beaumont
Request for Bid

BEAUMONT
-CALIFORNIA-

IRAN CONTRACTING ACT CERTIFICATION
City-wide Facility Painting
As required by California Public Contract Code Section 2204, the Contractor certifies subject to penalty for perjury that the option checked below relating to the Contractor's status in regard to the Iran Contracting Act of 2010 (Public Contract Code Section 2200 et seq.) is true and correct:
❑ The Contractor is not:
(1) identified on the current list of person and entities engaged in investment activities in Iran prepared by the California Department of General Services in accordance with subdivision (b) of Public Contract Code Section 2203; or (2) a financial instruction that extends, for 45 days or more, credit in the amount of $20,000,000 or more to any other person or entity identified on the current list of persons and entities engaging in investment activities in Iran prepared by the California Department of General Services in accordance with subdivision (b) of Public Contract Code Section 2203, if that person or entity uses or will use the credit to provide goods or services in the energy sector in Iran. ❑ The City has exempted the Contractor from the requirements of the Iran Contracting Act of 2010 after making a public finding that, absent the exemption, the City will be unable to obtain the goods and/or services to be provided pursuant to the Contract.
❑ The amount of the Contract payable to the Contractor for the Project does not exceed $1,000,000.

Signature:

Printed Name:

Title:

Firm Name:

Date:

Note: In accordance with Public Contract Code Section 2205, false certification of this form shall be reported to the California Attorney General and may result in civil penalties equal to the greater of $250,000 or twice the Contract amount, termination of the Contract and/or ineligibility to bid on contracts for three years.

Page 2056 of 2226 ends

City of Beaumont
Request for Bid

BEAUMONT
-CALIFORNIA-

FLEET COMPLIANCE CERTIFICATION
City-wide Facility Painting
Bidder hereby acknowledges that they have reviewed the California Air Resources Board's policies, rules and regulations and are familiar with the requirements of Title 13, California Code of Regulations, Division 3, Chapter 9, effective on January 1, 2024 (the "Regulation"). Bidder hereby certifies, subject to penalty for perjury, that the option checked below relating to the Bidder's fleet, and/or that of their subcontractor(s) ("Fleet") is true and correct:
❑ The Fleet is subject to the requirements of the Regulation, and the appropriate Certificate(s) of Reported Compliance have been attached hereto. ❑ The Fleet is exempt from the Regulation under section 2449.1(f)(2), and a signed description of the subject vehicles, and reasoning for exemption has been attached hereto.
❑ Bidder and/or their subcontractor is unable to procure R99 or R100 renewable diesel fuel as defined in the Regulation pursuant to section 2449.1(f)(3). Bidder shall keep detailed records describing the normal refueling methods, their attempts to procure renewable diesel fuel and proof that shows they were not able to procure renewable diesel (i.e. third party correspondence or vendor bids).
❑ The Fleet is exempt from the requirements of the Regulation pursuant to section 2449(i)(4) because this Project has been deemed an Emergency, as defined under section 2449(c)(18). Bidder shall only operate the exempted vehicles in the emergency situation and records of the exempted vehicles must be maintained, pursuant to section 2449(i)(4).
❑ The Fleet does not fall under the Regulation or are otherwise exempted and a detailed reasoning is attached hereto.

Firm Name:

Signature:

Printed Name:

Title:

Date:

Page 2057 of 2226 ends

City of Beaumont
Request for Bid

BEAUMONT
-CALIFORNIA-
City-wide Facility Painting

CONTRACTOR'S CERTIFICATE REGARDING

WORKERS' COMPENSATION
City-wide Facility Painting
I am aware of the provisions of Section 3700 of the Labor Code which require every employer to be insured against liability for workers' compensation or to undertake self- insurance in accordance with the provisions of that code, and I will comply with such provisions before commencing the performance of the work of this Contract.

Name of Bidder
Signature
Name and Title
Dated

Page 2058 of 2226 ends

City of Beaumont
Request for Bid
The makers of this bond are,

BEAUMONT
-CALIFORNIA-

BID BOND
City-wide Facility Painting
City-wide Facility Painting
as Principal, and
, as Surety
and are held and firmly bound unto the City of Beaumont, hereinafter called the City, in the penal sum of TEN PERCENT (10%) OF THE TOTAL BID PRICE of the Principal submitted to CITY for the work described below, for the payment of which sum in lawful money of the United States, well and truly to be made, we bind ourselves, our heirs, executors, administrators, successors and assigns, jointly and severally, firmly by these presents.

THE CONDITION OF THIS OBLIGATION IS SUCH that whereas the Principal has submitted the accompanying bid dated , 2025, for
City-wide Facility Painting
If the Principal does not withdraw its bid within the time specified in the Contract Documents; and if the Principal is awarded the Contract and provides all documents to the City as required by the Contract Documents; then this obligation shall be null and void. Otherwise, this bond will remain in full force and effect.

Surety, for value received, hereby stipulates and agrees that no change, extension of time, alteration or addition to the terms of the Contract Documents shall in affect its obligation under this bond, and Surety does hereby waive notice of any such changes.

In the event a lawsuit is brought upon this bond by the City and judgment is recovered, the Surety shall pay all litigation expenses incurred by the City in such suit, including reasonable attorneys' fees, court costs, expert witness fees and expenses.

Page 2059 of 2226 ends

City of Beaumont
Request for Bid
;:=,.;',

BE MONT
-CALIFORNIA-
City-wide
IN WITNESS WHEREOF, the above -bound parties have executed this instrument under their several seals this day of , 2025, the name and
corporate seal of each corporation.
(Corporate Seal)
Principal
By
Title
(Corporate Seal) Surety
By
Attorney -in -Fact
(Attach Attorney -in -Fact Certificate) Title
22

Page 2060 of 2226 ends

City of Beaumont
Request for Bid

BEAUMONT
-CALIFORNIA-
City-wide Facility Painting

STATE OF CALIFORNIA )
) ss.

CITY OF )
On this day of , in the year 2025, before me,
, a Notary Public in and for said state, personally
appeared , known to me to be the person
whose name is subscribed to the within instrument as the Attorney -In -Fact of the (Surety) acknowledged to me that he subscribed the name of the (Surety) thereto and his own name as Attorney -In -
Fact.

Notary Public in and for said State
(SEAL)
Commission expires:

NOTE: A copy of the Power -of -Attorney to local representatives of the bonding company must be attached hereto.

Page 2061 of 2226 ends

City of Beaumont
Request for Bid

BEAUMONT
-CALIFORNIA-

PAYMENT BOND
KNOW ALL MEN BY THESE PRESENTS That
City-wide Facility Painting
WHEREAS, the City of Beaumont (hereinafter designated as the "City"), by action taken or a resolution passed , 20 has awarded to hereinafter designated as the "Principal," a contract for the work described as follows:
(the
"Project"); and
WHEREAS, said Principal is required to furnish a bond in connection with said contract; providing that if said Principal or any of its Subcontractors shall fail to pay for any materials, provisions, provender, equipment, or other supplies used in, upon, for or about the performance of the work contracted to be done, or for any work or labor done thereon of any kind, or for amounts due under the Unemployment Insurance Code or for any amounts required to be deducted, withheld, and paid over to the Employment Development Department from the wages of employees of said Principal and its Subcontractors with respect to such work or labor the Surety on this bond will pay for the same to the extent hereinafter set forth.

NOW THEREFORE, we, the Principal and as Surety, are held and firmly bound unto the City in the penal sum of Dollars ($ ) lawful money of the United States of America, for the payment of which sum well and truly to be made, we bind ourselves, our heirs, executors, administrators, successors and assigns, jointly and severally, firmly by these presents.

THE CONDITION OF THIS OBLIGATION IS SUCH that if said Principal, his or its subcontractors, heirs, executors, administrators, successors or assigns, shall fail to pay any of the persons named in Section 3181 of the Civil Code, fail to pay for any materials, provisions or other supplies, used in, upon, for or about the performance of the work contracted to be done, or for any work or labor thereon of any kind, or amounts due under the Unemployment Insurance Code with respect to work or labor performed under the contract, or for any amounts required to be deducted, withheld, and paid over to the Employment Development Department or Franchise Tax Board from the wages of employees of the contractor and his subcontractors pursuant to Section 18663 of the Revenue and Taxation Code, with respect to such work and labor the Surety or Sureties will pay for the same, in an amount not exceeding the sum herein above specified, and also, in case suit is brought upon this bond, all litigation expenses incurred by the City in such suit, including reasonable attorneys' fees, court costs, expert witness fees and investigation expenses.

This bond shall inure to the benefit of any of the persons named in Section 3181 of the Civil Code so as to give a right of action to such persons or their assigns in any suit brought upon this bond.

It is further stipulated and agreed that the Surety on this bond shall not be exonerated or released from the obligation of this bond by any change, extension of time for performance, addition, alteration or modification in, to, or of any contract, plans, specifications, or agreement pertaining or relating to any scheme or work of improvement herein above described, or pertaining or relating to the furnishing of labor, materials, or equipment therefore, nor by any change or modification of any terms of payment or extension of the time for any payment pertaining or relating to any scheme or work of improvement herein above described, nor by any rescission or attempted rescission or attempted rescission of the contract, agreement or bond, nor by any conditions precedent or subsequent in the bond attempting to limit the right of recovery of claimants otherwise entitled to recover under any such contract or agreement or under the bond, nor by any fraud practiced by any person other than the claimant seeking to recover on the bond and that this bond be construed most strongly against the Surety and in favor of all persons for whose benefit such bond is given, and under no circumstances shall Surety be released from liability to those for whose benefit such bond has been given, by reason of any

Page 2062 of 2226 ends

City of Beaumont
Request for Bid

BEAUMONT
-CALIFORNIA-
breach of contract between the owner or City and original contractor or on the part of any obligee named in such bond, but the sole conditions of recovery shall be that claimant is a person described in Section 3110 or 3112 of the Civil Code, and has not been paid the full amount of his claim and that Surety does hereby waive notice of any such change, extension of time, addition, alteration or modification herein mentioned.

IN WITNESS WHEREOF, two (2) identical counterparts of this instrument, each of which shall for all purposes be deemed unoriginal thereof, have been duly executed by the Principal and Surety above named, on the day of 20 the name and corporate seal of each corporate party being hereto affixed and these presents duly signed by its undersigned representative pursuant to authority of its governing body.
(Corporate Seal of Principal,
if corporation) Principal (Property Name of Contractor) City-wide Facility Painting
(Seal of Surety)
By
By
(Signature of Contractor)
Surety
Attorney in Fact
(Attached Attorney -In -Fact Certificate and Required Acknowledgements) *Note: Appropriate Notarial Acknowledgments of Execution by Contractor and +surety and a power of Attorney MUST BE ATTACHED.

Page 2063 of 2226 ends

City-wide Facility Painting
City of Beaumont
Request for Bid

BEAUMONT
-CALIFORNIA

DESIGNATION OF SUBCONTRACTORS
City-wide Facility Painting
In compliance with the Subletting and Subcontracting Fair Practices Act of the Public Contract Code of the State of California, each bidder shall set forth below: the name, the location of the place of business, the California contractor license number, and public works contractor registration number issued of each subcontractor who will perform work or labor or render service to the prime contractor in or about the construction of the work or improvement, or a subcontractor licensed by the State of California who, under subcontract to the prime contractor, specially fabricates and installs a portion of the work or improvement according to detailed drawings contained in the plans and specifications, in an amount in excess of one-half of 1 percent of the prime contractor's total bid.

Portion of the
Work
Subcontractor
Location of
Business
License
Number.

Public Works
Contractor
Registration
Number
% of
Work
26

Page 2064 of 2226 ends

City of Beaumont
Request for Bid

BEAUMONT
-CALIFORNIA-
City-wide Facility Painting
Portion of the
Work
Subcontractor
Location of
Business
License
Number.

Public Works
Contractor
Registration
Number
% of
Work
27

Page 2065 of 2226 ends

City of Beaumont
Request for Bid

BEAUMONT
-CALIFORNIA-
City-wide Facility Painting
Portion of the
Work
Subcontractor
Location of
Business
License
Number.

Public Works
Contractor
Registration
Number
% of
Work
Name of Bidder
Signature
Name and Title
Dated
28

Page 2066 of 2226 ends

City-wide Facility Painting
City of Beaumont
Request for bid

BEAUMONT
-CALIFORNIA-

INFORMATION REQUIRED OF BIDDERS
City-wide Facility Painting
A. INFORMATION ABOUT BIDDER
[**Indicate not applicable ("N/A") where appropriate.**] NOTE: Where Bidder is a joint venture, pages shall be duplicated and information provided for all parties to the joint venture.

1.0 Name of Bidder:

2.0 Type, if Entity:

3.0 Bidder Address:

Facsimile Number Telephone Number

4.0 License Information:

License No.

Class of License Expiration Date
DIR Registration No.

5.0 How many years has Bidder's organization been in business as a Contractor?

6.0 How many years has Bidder's organization been in business under its present name?

5.1 Under what other or former names has Bidder's organization operated?

Page 2067 of 2226 ends

City of Beaumont
Request for bid
;:=,.;',

BE MONT
-CALIFORNIA-
City-wide

7.0 If Bidder's organization is a corporation, answer the following:

7.1 Date of Incorporation:

7.2 State of Incorporation:

7.3 President's Name:

7.4 Vice -President's Name(s):

7.5 Secretary's Name:

7.6 Treasurer's Name:

8.0 If an individual or a partnership, answer the following:

8.1 Date of Organization:

8.2 Name and address of all partners (state whether general or limited partnership):

9.0 If other than a corporation or partnership, describe organization and name principals:

10.0 List other states in which Bidder's organization is legally qualified to do business. 30

Page 2068 of 2226 ends

City-wide Facility Painting
City of Beaumont
Request for bid

BEAUMONT
-CALIFORNIA-

11.0 What type of work does the Bidder normally perform with its own forces?

12.0 Has Bidder ever failed to complete any work awarded to it? If so, note when, where, and why:

13.0 Within the last five years, has any officer or partner of Bidder's organization ever been an officer or partner of another organization when it failed to complete a contract? If so, attach a separate sheet of explanation:

14.0 List Trade References:

15.0 List Bank References (Bank and Branch Address):

Page 2069 of 2226 ends

Beaumont City CouncilJuly 21, 2026

Beaumont City Council
July 21, 2026